From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Vinod Koul <vkoul@kernel.org>
Cc: Mark Brown <broonie@kernel.org>,
linux-arm-msm@vger.kernel.org, Andy Gross <agross@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH 4/4] regulator: qcom-rpmh: Update PMIC modes for PMIC5
Date: Fri, 9 Aug 2019 11:00:14 -0700 [thread overview]
Message-ID: <20190809180014.GP26807@tuxbook-pro> (raw)
In-Reply-To: <20190809073616.1235-4-vkoul@kernel.org>
On Fri 09 Aug 00:36 PDT 2019, Vinod Koul wrote:
> Add the PMIC5 modes and use them pmic5 ldo and smps
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> drivers/regulator/qcom-rpmh-regulator.c | 52 +++++++++++++++++++++----
> 1 file changed, 45 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
> index 391ed844a251..db6c085da65e 100644
> --- a/drivers/regulator/qcom-rpmh-regulator.c
> +++ b/drivers/regulator/qcom-rpmh-regulator.c
> @@ -50,6 +50,20 @@ enum rpmh_regulator_type {
> #define PMIC4_BOB_MODE_AUTO 2
> #define PMIC4_BOB_MODE_PWM 3
>
> +#define PMIC5_LDO_MODE_RETENTION 3
> +#define PMIC5_LDO_MODE_LPM 4
> +#define PMIC5_LDO_MODE_HPM 7
> +
> +#define PMIC5_SMPS_MODE_RETENTION 3
> +#define PMIC5_SMPS_MODE_PFM 4
> +#define PMIC5_SMPS_MODE_AUTO 6
> +#define PMIC5_SMPS_MODE_PWM 7
> +
> +#define PMIC5_BOB_MODE_PASS 2
> +#define PMIC5_BOB_MODE_PFM 4
> +#define PMIC5_BOB_MODE_AUTO 6
> +#define PMIC5_BOB_MODE_PWM 7
> +
> /**
> * struct rpmh_vreg_hw_data - RPMh regulator hardware configurations
> * @regulator_type: RPMh accelerator type used to manage this
> @@ -488,6 +502,14 @@ static const int pmic_mode_map_pmic4_ldo[REGULATOR_MODE_STANDBY + 1] = {
> [REGULATOR_MODE_FAST] = -EINVAL,
> };
>
> +static const int pmic_mode_map_pmic5_ldo[REGULATOR_MODE_STANDBY + 1] = {
> + [REGULATOR_MODE_INVALID] = -EINVAL,
> + [REGULATOR_MODE_STANDBY] = PMIC5_LDO_MODE_RETENTION,
> + [REGULATOR_MODE_IDLE] = PMIC5_LDO_MODE_LPM,
> + [REGULATOR_MODE_NORMAL] = PMIC5_LDO_MODE_HPM,
> + [REGULATOR_MODE_FAST] = -EINVAL,
> +};
> +
> static unsigned int rpmh_regulator_pmic4_ldo_of_map_mode(unsigned int rpmh_mode)
> {
> unsigned int mode;
> @@ -518,6 +540,14 @@ static const int pmic_mode_map_pmic4_smps[REGULATOR_MODE_STANDBY + 1] = {
> [REGULATOR_MODE_FAST] = PMIC4_SMPS_MODE_PWM,
> };
>
> +static const int pmic_mode_map_pmic5_smps[REGULATOR_MODE_STANDBY + 1] = {
> + [REGULATOR_MODE_INVALID] = -EINVAL,
> + [REGULATOR_MODE_STANDBY] = PMIC5_SMPS_MODE_RETENTION,
> + [REGULATOR_MODE_IDLE] = PMIC5_SMPS_MODE_PFM,
> + [REGULATOR_MODE_NORMAL] = PMIC5_SMPS_MODE_AUTO,
> + [REGULATOR_MODE_FAST] = PMIC5_SMPS_MODE_PWM,
> +};
> +
> static unsigned int
> rpmh_regulator_pmic4_smps_of_map_mode(unsigned int rpmh_mode)
> {
> @@ -552,6 +582,14 @@ static const int pmic_mode_map_pmic4_bob[REGULATOR_MODE_STANDBY + 1] = {
> [REGULATOR_MODE_FAST] = PMIC4_BOB_MODE_PWM,
> };
>
> +static const int pmic_mode_map_pmic5_bob[REGULATOR_MODE_STANDBY + 1] = {
> + [REGULATOR_MODE_INVALID] = -EINVAL,
> + [REGULATOR_MODE_STANDBY] = -EINVAL,
> + [REGULATOR_MODE_IDLE] = PMIC5_BOB_MODE_PFM,
> + [REGULATOR_MODE_NORMAL] = PMIC5_BOB_MODE_AUTO,
> + [REGULATOR_MODE_FAST] = PMIC5_BOB_MODE_PWM,
> +};
> +
> static unsigned int rpmh_regulator_pmic4_bob_of_map_mode(unsigned int rpmh_mode)
> {
> unsigned int mode;
> @@ -643,7 +681,7 @@ static const struct rpmh_vreg_hw_data pmic5_pldo = {
> .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
> .n_voltages = 256,
> .hpm_min_load_uA = 10000,
> - .pmic_mode_map = pmic_mode_map_pmic4_ldo,
> + .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> };
>
> @@ -653,7 +691,7 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
> .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
> .n_voltages = 63,
> .hpm_min_load_uA = 10000,
> - .pmic_mode_map = pmic_mode_map_pmic4_ldo,
> + .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> };
>
> @@ -663,7 +701,7 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = {
> .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
> .n_voltages = 124,
> .hpm_min_load_uA = 30000,
> - .pmic_mode_map = pmic_mode_map_pmic4_ldo,
> + .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> };
>
> @@ -672,7 +710,7 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
> .ops = &rpmh_regulator_vrm_ops,
> .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> .n_voltages = 216,
> - .pmic_mode_map = pmic_mode_map_pmic4_smps,
> + .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> };
>
> @@ -681,7 +719,7 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
> .ops = &rpmh_regulator_vrm_ops,
> .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
> .n_voltages = 264,
> - .pmic_mode_map = pmic_mode_map_pmic4_smps,
> + .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> };
>
> @@ -690,7 +728,7 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
> .ops = &rpmh_regulator_vrm_ops,
> .voltage_range = REGULATOR_LINEAR_RANGE(2800000, 0, 4, 1600),
> .n_voltages = 5,
> - .pmic_mode_map = pmic_mode_map_pmic4_smps,
> + .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> };
>
> @@ -699,7 +737,7 @@ static const struct rpmh_vreg_hw_data pmic5_bob = {
> .ops = &rpmh_regulator_vrm_bypass_ops,
> .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 135, 32000),
> .n_voltages = 136,
> - .pmic_mode_map = pmic_mode_map_pmic4_bob,
> + .pmic_mode_map = pmic_mode_map_pmic5_bob,
> .of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
> };
>
> --
> 2.20.1
>
next prev parent reply other threads:[~2019-08-09 17:58 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-09 7:36 [PATCH 1/4] regulator: dt-bindings: Sort the compatibles and nodes Vinod Koul
2019-08-09 7:36 ` [PATCH 2/4] regulator: qcom-rpmh: Sort the compatibles Vinod Koul
2019-08-09 12:31 ` Applied "regulator: qcom-rpmh: Sort the compatibles" to the regulator tree Mark Brown
2019-08-09 17:02 ` [PATCH 2/4] regulator: qcom-rpmh: Sort the compatibles Bjorn Andersson
2019-08-09 7:36 ` [PATCH 3/4] regulator: qcom-rpmh: Fix pmic5_bob voltage count Vinod Koul
2019-08-09 12:31 ` Applied "regulator: qcom-rpmh: Fix pmic5_bob voltage count" to the regulator tree Mark Brown
2019-08-09 17:03 ` [PATCH 3/4] regulator: qcom-rpmh: Fix pmic5_bob voltage count Bjorn Andersson
2019-08-09 7:36 ` [PATCH 4/4] regulator: qcom-rpmh: Update PMIC modes for PMIC5 Vinod Koul
2019-08-09 12:31 ` Applied "regulator: qcom-rpmh: Update PMIC modes for PMIC5" to the regulator tree Mark Brown
2019-08-09 18:00 ` Bjorn Andersson [this message]
2019-08-09 12:31 ` Applied "regulator: dt-bindings: Sort the compatibles and nodes" " Mark Brown
2019-08-09 17:01 ` [PATCH 1/4] regulator: dt-bindings: Sort the compatibles and nodes Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190809180014.GP26807@tuxbook-pro \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).