From: Bhupesh Sharma <bhupesh.sharma@linaro.org>
To: linux-arm-msm@vger.kernel.org
Cc: bhupesh.sharma@linaro.org,
Linus Walleij <linus.walleij@linaro.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Andy Gross <agross@kernel.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-gpio@vger.kernel.org, bhupesh.linux@gmail.com
Subject: [PATCH 4/8] regulator: qcom-rpmh: Add new regulator types found on SA8155p adp board
Date: Mon, 7 Jun 2021 17:08:36 +0530 [thread overview]
Message-ID: <20210607113840.15435-5-bhupesh.sharma@linaro.org> (raw)
In-Reply-To: <20210607113840.15435-1-bhupesh.sharma@linaro.org>
SA8155p-adp board has two new regulator types - pmm8155au_1 and
pmm8155au_2.
The output power management circuits in these regulators include:
- FTS510 smps,
- HFS510 smps, and
- LDO510 linear regulators
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: bhupesh.linux@gmail.com
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
drivers/regulator/qcom-rpmh-regulator.c | 72 +++++++++++++++++++++++++
1 file changed, 72 insertions(+)
diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
index 22fec370fa61..d0a3c6527568 100644
--- a/drivers/regulator/qcom-rpmh-regulator.c
+++ b/drivers/regulator/qcom-rpmh-regulator.c
@@ -883,6 +883,70 @@ static const struct rpmh_vreg_init_data pm8150l_vreg_data[] = {
{},
};
+static const struct rpmh_vreg_init_data pmm8155au_1_vreg_data[] = {
+ RPMH_VREG("smps1", "smp%s1", &pmic5_ftsmps510, "vdd-s1"),
+ RPMH_VREG("smps2", "smp%s2", &pmic5_ftsmps510, "vdd-s2"),
+ RPMH_VREG("smps3", "smp%s3", &pmic5_ftsmps510, "vdd-s3"),
+ RPMH_VREG("smps4", "smp%s4", &pmic5_hfsmps510, "vdd-s4"),
+ RPMH_VREG("smps5", "smp%s5", &pmic5_hfsmps510, "vdd-s5"),
+ RPMH_VREG("smps6", "smp%s6", &pmic5_ftsmps510, "vdd-s6"),
+ RPMH_VREG("smps7", "smp%s7", &pmic5_ftsmps510, "vdd-s7"),
+ RPMH_VREG("smps8", "smp%s8", &pmic5_ftsmps510, "vdd-s8"),
+ RPMH_VREG("smps9", "smp%s9", &pmic5_ftsmps510, "vdd-s9"),
+ RPMH_VREG("smps10", "smp%s10", &pmic5_ftsmps510, "vdd-s10"),
+ RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo, "vdd-l1-l8-l11"),
+ RPMH_VREG("ldo2", "ldo%s2", &pmic5_pldo, "vdd-l2-l10"),
+ RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ RPMH_VREG("ldo4", "ldo%s4", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ RPMH_VREG("ldo5", "ldo%s5", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ RPMH_VREG("ldo6", "ldo%s6", &pmic5_nldo, "vdd-l6-l9"),
+ RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo8", "ldo%s8", &pmic5_nldo, "vdd-l1-l8-l11"),
+ RPMH_VREG("ldo9", "ldo%s9", &pmic5_nldo, "vdd-l6-l9"),
+ RPMH_VREG("ldo10", "ldo%s10", &pmic5_pldo, "vdd-l2-l10"),
+ RPMH_VREG("ldo11", "ldo%s11", &pmic5_nldo, "vdd-l1-l8-l11"),
+ RPMH_VREG("ldo12", "ldo%s12", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo13", "ldo%s13", &pmic5_pldo, "vdd-l13-l16-l17"),
+ RPMH_VREG("ldo14", "ldo%s14", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo15", "ldo%s15", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo16", "ldo%s16", &pmic5_pldo, "vdd-l13-l16-l17"),
+ RPMH_VREG("ldo17", "ldo%s17", &pmic5_pldo, "vdd-l13-l16-l17"),
+ RPMH_VREG("ldo18", "ldo%s18", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ {},
+};
+
+static const struct rpmh_vreg_init_data pmm8155au_2_vreg_data[] = {
+ RPMH_VREG("smps1", "smp%s1", &pmic5_ftsmps510, "vdd-s1"),
+ RPMH_VREG("smps2", "smp%s2", &pmic5_ftsmps510, "vdd-s2"),
+ RPMH_VREG("smps3", "smp%s3", &pmic5_ftsmps510, "vdd-s3"),
+ RPMH_VREG("smps4", "smp%s4", &pmic5_hfsmps510, "vdd-s4"),
+ RPMH_VREG("smps5", "smp%s5", &pmic5_hfsmps510, "vdd-s5"),
+ RPMH_VREG("smps6", "smp%s6", &pmic5_ftsmps510, "vdd-s6"),
+ RPMH_VREG("smps7", "smp%s7", &pmic5_ftsmps510, "vdd-s7"),
+ RPMH_VREG("smps8", "smp%s8", &pmic5_ftsmps510, "vdd-s8"),
+ RPMH_VREG("smps9", "smp%s9", &pmic5_ftsmps510, "vdd-s9"),
+ RPMH_VREG("smps10", "smp%s10", &pmic5_ftsmps510, "vdd-s10"),
+ RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo, "vdd-l1-l8-l11"),
+ RPMH_VREG("ldo2", "ldo%s2", &pmic5_pldo, "vdd-l2-l10"),
+ RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ RPMH_VREG("ldo4", "ldo%s4", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ RPMH_VREG("ldo5", "ldo%s5", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ RPMH_VREG("ldo6", "ldo%s6", &pmic5_nldo, "vdd-l6-l9"),
+ RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo8", "ldo%s8", &pmic5_nldo, "vdd-l1-l8-l11"),
+ RPMH_VREG("ldo9", "ldo%s9", &pmic5_nldo, "vdd-l6-l9"),
+ RPMH_VREG("ldo10", "ldo%s10", &pmic5_pldo, "vdd-l2-l10"),
+ RPMH_VREG("ldo11", "ldo%s11", &pmic5_nldo, "vdd-l1-l8-l11"),
+ RPMH_VREG("ldo12", "ldo%s12", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo13", "ldo%s13", &pmic5_pldo, "vdd-l13-l16-l17"),
+ RPMH_VREG("ldo14", "ldo%s14", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo15", "ldo%s15", &pmic5_pldo_lv, "vdd-l7-l12-l14-l15"),
+ RPMH_VREG("ldo16", "ldo%s16", &pmic5_pldo, "vdd-l13-l16-l17"),
+ RPMH_VREG("ldo17", "ldo%s17", &pmic5_pldo, "vdd-l13-l16-l17"),
+ RPMH_VREG("ldo18", "ldo%s18", &pmic5_nldo, "vdd-l3-l4-l5-l18"),
+ {},
+};
+
static const struct rpmh_vreg_init_data pm8350_vreg_data[] = {
RPMH_VREG("smps1", "smp%s1", &pmic5_ftsmps510, "vdd-s1"),
RPMH_VREG("smps2", "smp%s2", &pmic5_ftsmps510, "vdd-s2"),
@@ -1143,6 +1207,14 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = {
.compatible = "qcom,pm8150l-rpmh-regulators",
.data = pm8150l_vreg_data,
},
+ {
+ .compatible = "qcom,pmm8155au-1-rpmh-regulators",
+ .data = pmm8155au_1_vreg_data,
+ },
+ {
+ .compatible = "qcom,pmm8155au-2-rpmh-regulators",
+ .data = pmm8155au_2_vreg_data,
+ },
{
.compatible = "qcom,pm8350-rpmh-regulators",
.data = pm8350_vreg_data,
--
2.31.1
next prev parent reply other threads:[~2021-06-07 11:40 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-07 11:38 [PATCH 0/8] arm64: dts: qcom: Add SA8155p-adp board DTS Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 1/8] dt-bindings: qcom: rpmh-regulator: Add compatible for SA8155p-adp board pmics Bhupesh Sharma
2021-06-11 2:48 ` Bjorn Andersson
2021-06-14 8:05 ` Bhupesh Sharma
2021-06-14 16:28 ` Bjorn Andersson
2021-06-15 4:43 ` Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 2/8] dt-bindings: pinctrl: qcom,pmic-gpio: Add compatible for SA8155p-adp Bhupesh Sharma
2021-06-11 2:51 ` Bjorn Andersson
2021-06-14 8:13 ` Bhupesh Sharma
2021-06-14 16:09 ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 3/8] dt-bindings: arm: qcom: Add compatible for SA8155p-adp board Bhupesh Sharma
2021-06-11 2:59 ` Bjorn Andersson
2021-06-14 8:14 ` Bhupesh Sharma
2021-06-07 11:38 ` Bhupesh Sharma [this message]
2021-06-07 12:09 ` [PATCH 4/8] regulator: qcom-rpmh: Add new regulator types found on SA8155p adp board Andy Shevchenko
2021-06-07 12:30 ` Bhupesh Sharma
2021-06-14 16:17 ` Bjorn Andersson
2021-06-15 4:47 ` Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 5/8] pinctrl: qcom/pinctrl-spmi-gpio: Add compatibles for pmic-gpios on SA8155p-adp Bhupesh Sharma
2021-06-11 3:00 ` Bjorn Andersson
2021-06-14 8:30 ` Bhupesh Sharma
2021-06-14 16:12 ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 6/8] arm64: dts: qcom: pmm8155au_1: Add base dts file Bhupesh Sharma
2021-06-11 3:12 ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 7/8] arm64: dts: qcom: pmm8155au_2: " Bhupesh Sharma
2021-06-11 3:13 ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 8/8] arm64: dts: qcom: sa8155p-adp: " Bhupesh Sharma
2021-06-07 15:22 ` Vinod Koul
2021-06-07 21:22 ` Bhupesh Sharma
2021-06-11 2:25 ` Bjorn Andersson
2021-06-14 8:19 ` Bhupesh Sharma
2021-06-15 4:41 ` Bhupesh Sharma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210607113840.15435-5-bhupesh.sharma@linaro.org \
--to=bhupesh.sharma@linaro.org \
--cc=agross@kernel.org \
--cc=bhupesh.linux@gmail.com \
--cc=bjorn.andersson@linaro.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).