* Re: [PATCH V5 3/3] ARM: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel [not found] ` <20191016135147.7743-3-aford173@gmail.com> @ 2019-10-21 17:19 ` Tony Lindgren 0 siblings, 0 replies; 7+ messages in thread From: Tony Lindgren @ 2019-10-21 17:19 UTC (permalink / raw) To: Adam Ford Cc: dri-devel, linux-omap, Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Tomi Valkeinen, Sebastian Reichel, Laurent Pinchart, devicetree, linux-kernel * Adam Ford <aford173@gmail.com> [191016 06:53]: > With the removal of the panel-dpi from the omap drivers, the > LCD no longer works. This patch points the device tree to > a newly created panel named "logicpd,type28" > > Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") > > Signed-off-by: Adam Ford <aford173@gmail.com> > Acked-by: Sam Ravnborg <sam@ravnborg.org> > --- > V5: No Change > V4: No Change > V3: No change > V2: Remove legacy 'label' from binding I'm picking this patch into omap-for-v5.5/dt thanks. Regards, Tony > diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts > index 07ac99b9cda6..cdb89b3e2a9b 100644 > --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts > +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts > @@ -11,22 +11,6 @@ > #include "logicpd-torpedo-37xx-devkit.dts" > > &lcd0 { > - > - label = "28"; > - > - panel-timing { > - clock-frequency = <9000000>; > - hactive = <480>; > - vactive = <272>; > - hfront-porch = <3>; > - hback-porch = <2>; > - hsync-len = <42>; > - vback-porch = <3>; > - vfront-porch = <2>; > - vsync-len = <11>; > - hsync-active = <1>; > - vsync-active = <1>; > - de-active = <1>; > - pixelclk-active = <0>; > - }; > + /* To make it work, set CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 */ > + compatible = "logicpd,type28"; > }; > -- > 2.17.1 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support [not found] <20191016135147.7743-1-aford173@gmail.com> [not found] ` <20191016135147.7743-3-aford173@gmail.com> @ 2019-10-30 14:44 ` Adam Ford 2019-11-01 7:57 ` Laurent Pinchart [not found] ` <20191016135147.7743-2-aford173@gmail.com> 2019-11-30 22:16 ` [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support Sam Ravnborg 3 siblings, 1 reply; 7+ messages in thread From: Adam Ford @ 2019-10-30 14:44 UTC (permalink / raw) To: dri-devel Cc: Linux-OMAP, Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Sebastian Reichel, Tomi Valkeinen, Laurent Pinchart, devicetree, Linux Kernel Mailing List On Wed, Oct 16, 2019 at 8:52 AM Adam Ford <aford173@gmail.com> wrote: > > Previously, there was an omap panel-dpi driver that would > read generic timings from the device tree and set the display > timing accordingly. This driver was removed so the screen > no longer functions. This patch modifies the panel-simple > file to setup the timings to the same values previously used. > > Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") > Will this be able to make it into linux-next for the 5.5 merge window? I believe Tony has picked up the device tree portion in his omap tree, but I haven't seen any notifications on this series on whether or not it's being applied. I also don't know which tree I need to look if it's already been applied. This fixes a regression introduced a while ago where the driver I was using for the display was removed. thank you, adam > Signed-off-by: Adam Ford <aford173@gmail.com> > Reviewed-by: Sam Ravnborg <sam@ravnborg.org> > --- > V5: No Change > V4: No Change > V3: No Change > V2: No Change > > diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c > index 5d487686d25c..72f69709f349 100644 > --- a/drivers/gpu/drm/panel/panel-simple.c > +++ b/drivers/gpu/drm/panel/panel-simple.c > @@ -2061,6 +2061,40 @@ static const struct drm_display_mode mitsubishi_aa070mc01_mode = { > .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC, > }; > > +static const struct drm_display_mode logicpd_type_28_mode = { > + .clock = 9000, > + .hdisplay = 480, > + .hsync_start = 480 + 3, > + .hsync_end = 480 + 3 + 42, > + .htotal = 480 + 3 + 42 + 2, > + > + .vdisplay = 272, > + .vsync_start = 272 + 2, > + .vsync_end = 272 + 2 + 11, > + .vtotal = 272 + 2 + 11 + 3, > + .vrefresh = 60, > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > +}; > + > +static const struct panel_desc logicpd_type_28 = { > + .modes = &logicpd_type_28_mode, > + .num_modes = 1, > + .bpc = 8, > + .size = { > + .width = 105, > + .height = 67, > + }, > + .delay = { > + .prepare = 200, > + .enable = 200, > + .unprepare = 200, > + .disable = 200, > + }, > + .bus_format = MEDIA_BUS_FMT_RGB888_1X24, > + .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE | > + DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE, > +}; > + > static const struct panel_desc mitsubishi_aa070mc01 = { > .modes = &mitsubishi_aa070mc01_mode, > .num_modes = 1, > @@ -3287,6 +3321,9 @@ static const struct of_device_id platform_of_match[] = { > }, { > .compatible = "lg,lp129qe", > .data = &lg_lp129qe, > + }, { > + .compatible = "logicpd,type28", > + .data = &logicpd_type_28, > }, { > .compatible = "mitsubishi,aa070mc01-ca1", > .data = &mitsubishi_aa070mc01, > -- > 2.17.1 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support 2019-10-30 14:44 ` [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support Adam Ford @ 2019-11-01 7:57 ` Laurent Pinchart 2019-11-11 13:19 ` Adam Ford 0 siblings, 1 reply; 7+ messages in thread From: Laurent Pinchart @ 2019-11-01 7:57 UTC (permalink / raw) To: Adam Ford, Sam Ravnborg Cc: dri-devel, Linux-OMAP, Thierry Reding, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Sebastian Reichel, Tomi Valkeinen, devicetree, Linux Kernel Mailing List On Wed, Oct 30, 2019 at 09:44:20AM -0500, Adam Ford wrote: > On Wed, Oct 16, 2019 at 8:52 AM Adam Ford <aford173@gmail.com> wrote: > > > > Previously, there was an omap panel-dpi driver that would > > read generic timings from the device tree and set the display > > timing accordingly. This driver was removed so the screen > > no longer functions. This patch modifies the panel-simple > > file to setup the timings to the same values previously used. > > > > Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") > > Will this be able to make it into linux-next for the 5.5 merge window? > I believe Tony has picked up the device tree portion in his omap > tree, but I haven't seen any notifications on this series on whether > or not it's being applied. I also don't know which tree I need to > look if it's already been applied. > > This fixes a regression introduced a while ago where the driver I was > using for the display was removed. Sam, would you be able to pick this up ? > > Signed-off-by: Adam Ford <aford173@gmail.com> > > Reviewed-by: Sam Ravnborg <sam@ravnborg.org> > > --- > > V5: No Change > > V4: No Change > > V3: No Change > > V2: No Change > > > > diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c > > index 5d487686d25c..72f69709f349 100644 > > --- a/drivers/gpu/drm/panel/panel-simple.c > > +++ b/drivers/gpu/drm/panel/panel-simple.c > > @@ -2061,6 +2061,40 @@ static const struct drm_display_mode mitsubishi_aa070mc01_mode = { > > .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC, > > }; > > > > +static const struct drm_display_mode logicpd_type_28_mode = { > > + .clock = 9000, > > + .hdisplay = 480, > > + .hsync_start = 480 + 3, > > + .hsync_end = 480 + 3 + 42, > > + .htotal = 480 + 3 + 42 + 2, > > + > > + .vdisplay = 272, > > + .vsync_start = 272 + 2, > > + .vsync_end = 272 + 2 + 11, > > + .vtotal = 272 + 2 + 11 + 3, > > + .vrefresh = 60, > > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > > +}; > > + > > +static const struct panel_desc logicpd_type_28 = { > > + .modes = &logicpd_type_28_mode, > > + .num_modes = 1, > > + .bpc = 8, > > + .size = { > > + .width = 105, > > + .height = 67, > > + }, > > + .delay = { > > + .prepare = 200, > > + .enable = 200, > > + .unprepare = 200, > > + .disable = 200, > > + }, > > + .bus_format = MEDIA_BUS_FMT_RGB888_1X24, > > + .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE | > > + DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE, > > +}; > > + > > static const struct panel_desc mitsubishi_aa070mc01 = { > > .modes = &mitsubishi_aa070mc01_mode, > > .num_modes = 1, > > @@ -3287,6 +3321,9 @@ static const struct of_device_id platform_of_match[] = { > > }, { > > .compatible = "lg,lp129qe", > > .data = &lg_lp129qe, > > + }, { > > + .compatible = "logicpd,type28", > > + .data = &logicpd_type_28, > > }, { > > .compatible = "mitsubishi,aa070mc01-ca1", > > .data = &mitsubishi_aa070mc01, -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support 2019-11-01 7:57 ` Laurent Pinchart @ 2019-11-11 13:19 ` Adam Ford 2019-11-24 11:17 ` Adam Ford 0 siblings, 1 reply; 7+ messages in thread From: Adam Ford @ 2019-11-11 13:19 UTC (permalink / raw) To: Laurent Pinchart Cc: Sam Ravnborg, dri-devel, Linux-OMAP, Thierry Reding, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Sebastian Reichel, Tomi Valkeinen, devicetree, Linux Kernel Mailing List On Fri, Nov 1, 2019 at 2:57 AM Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote: > > On Wed, Oct 30, 2019 at 09:44:20AM -0500, Adam Ford wrote: > > On Wed, Oct 16, 2019 at 8:52 AM Adam Ford <aford173@gmail.com> wrote: > > > > > > Previously, there was an omap panel-dpi driver that would > > > read generic timings from the device tree and set the display > > > timing accordingly. This driver was removed so the screen > > > no longer functions. This patch modifies the panel-simple > > > file to setup the timings to the same values previously used. > > > > > > Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") > > > > Will this be able to make it into linux-next for the 5.5 merge window? > > I believe Tony has picked up the device tree portion in his omap > > tree, but I haven't seen any notifications on this series on whether > > or not it's being applied. I also don't know which tree I need to > > look if it's already been applied. > > > > This fixes a regression introduced a while ago where the driver I was > > using for the display was removed. > > Sam, would you be able to pick this up ? Gentle nudge with the merge window approaching. Thank you, adam > > > > Signed-off-by: Adam Ford <aford173@gmail.com> > > > Reviewed-by: Sam Ravnborg <sam@ravnborg.org> > > > --- > > > V5: No Change > > > V4: No Change > > > V3: No Change > > > V2: No Change > > > > > > diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c > > > index 5d487686d25c..72f69709f349 100644 > > > --- a/drivers/gpu/drm/panel/panel-simple.c > > > +++ b/drivers/gpu/drm/panel/panel-simple.c > > > @@ -2061,6 +2061,40 @@ static const struct drm_display_mode mitsubishi_aa070mc01_mode = { > > > .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC, > > > }; > > > > > > +static const struct drm_display_mode logicpd_type_28_mode = { > > > + .clock = 9000, > > > + .hdisplay = 480, > > > + .hsync_start = 480 + 3, > > > + .hsync_end = 480 + 3 + 42, > > > + .htotal = 480 + 3 + 42 + 2, > > > + > > > + .vdisplay = 272, > > > + .vsync_start = 272 + 2, > > > + .vsync_end = 272 + 2 + 11, > > > + .vtotal = 272 + 2 + 11 + 3, > > > + .vrefresh = 60, > > > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > > > +}; > > > + > > > +static const struct panel_desc logicpd_type_28 = { > > > + .modes = &logicpd_type_28_mode, > > > + .num_modes = 1, > > > + .bpc = 8, > > > + .size = { > > > + .width = 105, > > > + .height = 67, > > > + }, > > > + .delay = { > > > + .prepare = 200, > > > + .enable = 200, > > > + .unprepare = 200, > > > + .disable = 200, > > > + }, > > > + .bus_format = MEDIA_BUS_FMT_RGB888_1X24, > > > + .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE | > > > + DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE, > > > +}; > > > + > > > static const struct panel_desc mitsubishi_aa070mc01 = { > > > .modes = &mitsubishi_aa070mc01_mode, > > > .num_modes = 1, > > > @@ -3287,6 +3321,9 @@ static const struct of_device_id platform_of_match[] = { > > > }, { > > > .compatible = "lg,lp129qe", > > > .data = &lg_lp129qe, > > > + }, { > > > + .compatible = "logicpd,type28", > > > + .data = &logicpd_type_28, > > > }, { > > > .compatible = "mitsubishi,aa070mc01-ca1", > > > .data = &mitsubishi_aa070mc01, > > -- > Regards, > > Laurent Pinchart ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support 2019-11-11 13:19 ` Adam Ford @ 2019-11-24 11:17 ` Adam Ford 0 siblings, 0 replies; 7+ messages in thread From: Adam Ford @ 2019-11-24 11:17 UTC (permalink / raw) To: Laurent Pinchart Cc: Sam Ravnborg, dri-devel, Linux-OMAP, Thierry Reding, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Sebastian Reichel, Tomi Valkeinen, devicetree, Linux Kernel Mailing List On Mon, Nov 11, 2019 at 7:19 AM Adam Ford <aford173@gmail.com> wrote: > > On Fri, Nov 1, 2019 at 2:57 AM Laurent Pinchart > <laurent.pinchart@ideasonboard.com> wrote: > > > > On Wed, Oct 30, 2019 at 09:44:20AM -0500, Adam Ford wrote: > > > On Wed, Oct 16, 2019 at 8:52 AM Adam Ford <aford173@gmail.com> wrote: > > > > > > > > Previously, there was an omap panel-dpi driver that would > > > > read generic timings from the device tree and set the display > > > > timing accordingly. This driver was removed so the screen > > > > no longer functions. This patch modifies the panel-simple > > > > file to setup the timings to the same values previously used. > > > > > > > > Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") > > > > > > Will this be able to make it into linux-next for the 5.5 merge window? > > > I believe Tony has picked up the device tree portion in his omap > > > tree, but I haven't seen any notifications on this series on whether > > > or not it's being applied. I also don't know which tree I need to > > > look if it's already been applied. > > > > > > This fixes a regression introduced a while ago where the driver I was > > > using for the display was removed. > > > > Sam, would you be able to pick this up ? > Sam, > Gentle nudge with the merge window approaching. Is it too late for 5.5? :-( adam > > Thank you, > > adam > > > > > > > Signed-off-by: Adam Ford <aford173@gmail.com> > > > > Reviewed-by: Sam Ravnborg <sam@ravnborg.org> > > > > --- > > > > V5: No Change > > > > V4: No Change > > > > V3: No Change > > > > V2: No Change > > > > > > > > diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c > > > > index 5d487686d25c..72f69709f349 100644 > > > > --- a/drivers/gpu/drm/panel/panel-simple.c > > > > +++ b/drivers/gpu/drm/panel/panel-simple.c > > > > @@ -2061,6 +2061,40 @@ static const struct drm_display_mode mitsubishi_aa070mc01_mode = { > > > > .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC, > > > > }; > > > > > > > > +static const struct drm_display_mode logicpd_type_28_mode = { > > > > + .clock = 9000, > > > > + .hdisplay = 480, > > > > + .hsync_start = 480 + 3, > > > > + .hsync_end = 480 + 3 + 42, > > > > + .htotal = 480 + 3 + 42 + 2, > > > > + > > > > + .vdisplay = 272, > > > > + .vsync_start = 272 + 2, > > > > + .vsync_end = 272 + 2 + 11, > > > > + .vtotal = 272 + 2 + 11 + 3, > > > > + .vrefresh = 60, > > > > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC, > > > > +}; > > > > + > > > > +static const struct panel_desc logicpd_type_28 = { > > > > + .modes = &logicpd_type_28_mode, > > > > + .num_modes = 1, > > > > + .bpc = 8, > > > > + .size = { > > > > + .width = 105, > > > > + .height = 67, > > > > + }, > > > > + .delay = { > > > > + .prepare = 200, > > > > + .enable = 200, > > > > + .unprepare = 200, > > > > + .disable = 200, > > > > + }, > > > > + .bus_format = MEDIA_BUS_FMT_RGB888_1X24, > > > > + .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE | > > > > + DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE, > > > > +}; > > > > + > > > > static const struct panel_desc mitsubishi_aa070mc01 = { > > > > .modes = &mitsubishi_aa070mc01_mode, > > > > .num_modes = 1, > > > > @@ -3287,6 +3321,9 @@ static const struct of_device_id platform_of_match[] = { > > > > }, { > > > > .compatible = "lg,lp129qe", > > > > .data = &lg_lp129qe, > > > > + }, { > > > > + .compatible = "logicpd,type28", > > > > + .data = &logicpd_type_28, > > > > }, { > > > > .compatible = "mitsubishi,aa070mc01-ca1", > > > > .data = &mitsubishi_aa070mc01, > > > > -- > > Regards, > > > > Laurent Pinchart ^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <20191016135147.7743-2-aford173@gmail.com>]
* Re: [PATCH V5 2/3] dt-bindings: Add Logic PD Type 28 display panel [not found] ` <20191016135147.7743-2-aford173@gmail.com> @ 2019-11-30 22:15 ` Sam Ravnborg 0 siblings, 0 replies; 7+ messages in thread From: Sam Ravnborg @ 2019-11-30 22:15 UTC (permalink / raw) To: Adam Ford Cc: dri-devel, linux-omap, Thierry Reding, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Sebastian Reichel, Laurent Pinchart, Tomi Valkeinen, devicetree, linux-kernel Hi Adam. On Wed, Oct 16, 2019 at 08:51:46AM -0500, Adam Ford wrote: > This patch adds documentation of device tree bindings for the WVGA panel > Logic PD Type 28 display. > > Signed-off-by: Adam Ford <aford173@gmail.com> > --- > V5: Replace GPIO_ACTIVE_HIGH with 0 to fix make dt_binding_check -k > V4: Update per Rob H's suggestions and copy other panel yaml example from 5.4-rc1 > V3: Correct build errors from 'make dt_binding_check' > V2: Use YAML instead of TXT for binding > Applied to drm-misc-next. It was applied before the driver changes so we had bindings for the driver changes when applied. Sam ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support [not found] <20191016135147.7743-1-aford173@gmail.com> ` (2 preceding siblings ...) [not found] ` <20191016135147.7743-2-aford173@gmail.com> @ 2019-11-30 22:16 ` Sam Ravnborg 3 siblings, 0 replies; 7+ messages in thread From: Sam Ravnborg @ 2019-11-30 22:16 UTC (permalink / raw) To: Adam Ford Cc: dri-devel, linux-omap, Thierry Reding, David Airlie, Daniel Vetter, Rob Herring, Mark Rutland, Sebastian Reichel, Tomi Valkeinen, Laurent Pinchart, devicetree, linux-kernel Hi Adam. On Wed, Oct 16, 2019 at 08:51:45AM -0500, Adam Ford wrote: > Previously, there was an omap panel-dpi driver that would > read generic timings from the device tree and set the display > timing accordingly. This driver was removed so the screen > no longer functions. This patch modifies the panel-simple > file to setup the timings to the same values previously used. > > Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") > > Signed-off-by: Adam Ford <aford173@gmail.com> > Reviewed-by: Sam Ravnborg <sam@ravnborg.org> > --- > V5: No Change > V4: No Change > V3: No Change > V2: No Change Applied to drm-misc-next. Sorry for the delay - has been absent for a while. Sam ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-11-30 22:16 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- [not found] <20191016135147.7743-1-aford173@gmail.com> [not found] ` <20191016135147.7743-3-aford173@gmail.com> 2019-10-21 17:19 ` [PATCH V5 3/3] ARM: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel Tony Lindgren 2019-10-30 14:44 ` [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support Adam Ford 2019-11-01 7:57 ` Laurent Pinchart 2019-11-11 13:19 ` Adam Ford 2019-11-24 11:17 ` Adam Ford [not found] ` <20191016135147.7743-2-aford173@gmail.com> 2019-11-30 22:15 ` [PATCH V5 2/3] dt-bindings: Add Logic PD Type 28 display panel Sam Ravnborg 2019-11-30 22:16 ` [PATCH V5 1/3] drm/panel: simple: Add Logic PD Type 28 display support Sam Ravnborg
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).