Linux-mtd Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support
@ 2020-02-11 13:33 Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 1/9] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
                   ` (8 more replies)
  0 siblings, 9 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

Hi,

This series adds support for octal DTR flashes in the spi-nor framework,
and then adds hooks for the Cypress Semper flash which is an xSPI
compliant Octal DTR flash.

The Cadence QSPI controller driver is also updated to run in Octal DTR
mode.

Tested on TI J721e EVM with 1-bit ECC on the Cypress flash.

This series depends on [0].

[0] https://patchwork.kernel.org/patch/11355593/

Pratyush Yadav (9):
  spi: spi-mem: allow specifying whether an op is DTR or not
  spi: spi-mem: allow specifying a command's extension
  spi: cadence-quadspi: Add support for octal DTR flashes
  mtd: spi-nor: add support for DTR protocol
  mtd: spi-nor: get command opcode extension type from BFPT
  mtd: spi-nor: parse xSPI Profile 1.0 table
  mtd: spi-nor: use dummy cycle and address width info from SFDP
  mtd: spi-nor: enable octal DTR mode when possible
  mtd: spi-nor: add support for Cypress Semper flash

 drivers/mtd/spi-nor/spi-nor.c     | 595 +++++++++++++++++++++++++++---
 drivers/spi/spi-cadence-quadspi.c | 262 +++++++++++--
 drivers/spi/spi-mem.c             |  48 +++
 include/linux/mtd/spi-nor.h       |  55 ++-
 include/linux/spi/spi-mem.h       |  32 ++
 include/linux/spi/spi.h           |   2 +
 6 files changed, 890 insertions(+), 104 deletions(-)

--
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 1/9] spi: spi-mem: allow specifying whether an op is DTR or not
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 2/9] spi: spi-mem: allow specifying a command's extension Pratyush Yadav
                   ` (7 subsequent siblings)
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

Each phase is given a separate 'is_dtr' field so mixed protocols like
4S-4D-4D can be supported.

Also add the mode bits SPI_RX_DTR and SPI_TX_DTR so controllers can
specify whether they support DTR modes or not.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/spi/spi-mem.c       | 25 +++++++++++++++++++++++++
 include/linux/spi/spi-mem.h |  8 ++++++++
 include/linux/spi/spi.h     |  2 ++
 3 files changed, 35 insertions(+)

diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index e5a46f0eb93b..8c52ecc41a0e 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c
@@ -99,6 +99,17 @@ void spi_controller_dma_unmap_mem_op_data(struct spi_controller *ctlr,
 }
 EXPORT_SYMBOL_GPL(spi_controller_dma_unmap_mem_op_data);
 
+static int spi_check_dtr_req(struct spi_mem *mem, bool is_dtr, bool tx)
+{
+	u32 mode = mem->spi->mode;
+
+	if (is_dtr &&
+	    ((tx && (mode & SPI_TX_DTR)) || (!tx && (mode & SPI_RX_DTR))))
+			return 0;
+
+	return -ENOTSUPP;
+}
+
 static int spi_check_buswidth_req(struct spi_mem *mem, u8 buswidth, bool tx)
 {
 	u32 mode = mem->spi->mode;
@@ -154,6 +165,20 @@ bool spi_mem_default_supports_op(struct spi_mem *mem,
 				   op->data.dir == SPI_MEM_DATA_OUT))
 		return false;
 
+	if (op->cmd.is_dtr && spi_check_dtr_req(mem, op->cmd.is_dtr, true))
+		return false;
+
+	if (op->addr.is_dtr && spi_check_dtr_req(mem, op->addr.is_dtr, true))
+		return false;
+
+	if (op->dummy.is_dtr && spi_check_dtr_req(mem, op->dummy.is_dtr, true))
+		return false;
+
+	if (op->data.dir != SPI_MEM_NO_DATA &&
+	    spi_check_dtr_req(mem, op->data.is_dtr,
+			      op->data.dir == SPI_MEM_DATA_OUT))
+		return false;
+
 	return true;
 }
 EXPORT_SYMBOL_GPL(spi_mem_default_supports_op);
diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index af9ff2f0f1b2..4669082b4e3b 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h
@@ -71,6 +71,7 @@ enum spi_mem_data_dir {
  * struct spi_mem_op - describes a SPI memory operation
  * @cmd.buswidth: number of IO lines used to transmit the command
  * @cmd.opcode: operation opcode
+ * @cmd.is_dtr: whether the command opcode should be sent in DTR mode or not
  * @addr.nbytes: number of address bytes to send. Can be zero if the operation
  *		 does not need to send an address
  * @addr.buswidth: number of IO lines used to transmit the address cycles
@@ -78,10 +79,13 @@ enum spi_mem_data_dir {
  *	      Note that only @addr.nbytes are taken into account in this
  *	      address value, so users should make sure the value fits in the
  *	      assigned number of bytes.
+ * @addr.is_dtr: whether the address should be sent in DTR mode or not
  * @dummy.nbytes: number of dummy bytes to send after an opcode or address. Can
  *		  be zero if the operation does not require dummy bytes
  * @dummy.buswidth: number of IO lanes used to transmit the dummy bytes
+ * @dummy.is_dtr: whether the dummy bytes should be sent in DTR mode or not
  * @data.buswidth: number of IO lanes used to send/receive the data
+ * @data.is_dtr: whether the data should be sent in DTR mode or not
  * @data.dir: direction of the transfer
  * @data.nbytes: number of data bytes to send/receive. Can be zero if the
  *		 operation does not involve transferring data
@@ -92,21 +96,25 @@ struct spi_mem_op {
 	struct {
 		u8 buswidth;
 		u8 opcode;
+		bool is_dtr;
 	} cmd;
 
 	struct {
 		u8 nbytes;
 		u8 buswidth;
 		u64 val;
+		bool is_dtr;
 	} addr;
 
 	struct {
 		u8 nbytes;
 		u8 buswidth;
+		bool is_dtr;
 	} dummy;
 
 	struct {
 		u8 buswidth;
+		bool is_dtr;
 		enum spi_mem_data_dir dir;
 		unsigned int nbytes;
 		union {
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 6d16ba01ff5a..bf1108318389 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -183,6 +183,8 @@ struct spi_device {
 #define	SPI_TX_OCTAL	0x2000			/* transmit with 8 wires */
 #define	SPI_RX_OCTAL	0x4000			/* receive with 8 wires */
 #define	SPI_3WIRE_HIZ	0x8000			/* high impedance turnaround */
+#define SPI_RX_DTR	0x10000			/* receive in DTR mode */
+#define SPI_TX_DTR	0x20000			/* transmit in DTR mode */
 	int			irq;
 	void			*controller_state;
 	void			*controller_data;
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 2/9] spi: spi-mem: allow specifying a command's extension
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 1/9] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 3/9] spi: cadence-quadspi: Add support for octal DTR flashes Pratyush Yadav
                   ` (6 subsequent siblings)
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/spi/spi-mem.c       | 23 +++++++++++++++++++++++
 include/linux/spi/spi-mem.h | 24 ++++++++++++++++++++++++
 2 files changed, 47 insertions(+)

diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index 8c52ecc41a0e..fdae50d80715 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c
@@ -464,6 +464,29 @@ int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
 }
 EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size);
 
+int spi_mem_get_cmd_ext(const struct spi_mem_op *op, u8 *ext)
+{
+	switch (op->cmd.ext_type) {
+	case SPI_MEM_EXT_INVERT:
+		*ext = ~op->cmd.opcode;
+		break;
+
+	case SPI_MEM_EXT_REPEAT:
+		*ext = op->cmd.opcode;
+		break;
+
+	case SPI_MEM_EXT_HEX:
+		*ext = op->cmd.ext;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(spi_mem_get_cmd_ext);
+
 static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc *desc,
 				      u64 offs, size_t len, void *buf)
 {
diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index 4669082b4e3b..06ccab17e4d0 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h
@@ -67,11 +67,31 @@ enum spi_mem_data_dir {
 	SPI_MEM_DATA_OUT,
 };
 
+/**
+ * enum spi_mem_cmd_ext - describes the command opcode extension in DTR mode
+ * @SPI_MEM_EXT_NONE: no extension. This is the default, and is used in Legacy
+ *		      SPI mode
+ * @SPI_MEM_EXT_REPEAT: the extension is same as the opcode
+ * @SPI_MEM_EXT_INVERT: the extension is the bitwise inverse of the opcode
+ * @SPI_MEM_EXT_HEX: the extension is any hex value. The command and opcode
+ *		     combine to form a 16-bit opcode.
+ */
+enum spi_mem_cmd_ext {
+	SPI_MEM_EXT_NONE = 0,
+	SPI_MEM_EXT_REPEAT,
+	SPI_MEM_EXT_INVERT,
+	SPI_MEM_EXT_HEX,
+};
+
 /**
  * struct spi_mem_op - describes a SPI memory operation
  * @cmd.buswidth: number of IO lines used to transmit the command
  * @cmd.opcode: operation opcode
  * @cmd.is_dtr: whether the command opcode should be sent in DTR mode or not
+ * @cmd.ext_type: type of the command opcode extension in DTR mode
+ * @cmd.ext: value of the command opcode extension in DTR mode. It is
+ *	     only set when 'ext_type' is 'SPI_MEM_EXT_HEX'. In all other
+ *	     cases, the extension can be directly derived from the opcode.
  * @addr.nbytes: number of address bytes to send. Can be zero if the operation
  *		 does not need to send an address
  * @addr.buswidth: number of IO lines used to transmit the address cycles
@@ -97,6 +117,8 @@ struct spi_mem_op {
 		u8 buswidth;
 		u8 opcode;
 		bool is_dtr;
+		enum spi_mem_cmd_ext ext_type;
+		u8 ext;
 	} cmd;
 
 	struct {
@@ -361,6 +383,8 @@ int spi_mem_driver_register_with_owner(struct spi_mem_driver *drv,
 
 void spi_mem_driver_unregister(struct spi_mem_driver *drv);
 
+int spi_mem_get_cmd_ext(const struct spi_mem_op *op, u8 *ext);
+
 #define spi_mem_driver_register(__drv)                                  \
 	spi_mem_driver_register_with_owner(__drv, THIS_MODULE)
 
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 3/9] spi: cadence-quadspi: Add support for octal DTR flashes
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 1/9] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 2/9] spi: spi-mem: allow specifying a command's extension Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 4/9] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
                   ` (5 subsequent siblings)
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

Set up opcode extension and enable/disable DTR mode based on whether the
command is DTR or not.

xSPI flashes can have a 4-byte dummy address associated with some
commands like the Read Status Register command in octal DTR mode. Since
the flash does not support sending the dummy address, we can not use
automatic write completion polling in DTR mode. Further, no write
completion polling makes it impossible to use DAC mode for DTR writes.
In that mode, the controller does not know beforehand how long a write
will be and so it can de-assert Chip Select (CS#) at any time. Once CS#
is de-assert, the flash will go into burning phase. But since the
controller does not do write completion polling, it does not know when
the flash is busy and might send in writes while the flash is not ready.

So, disable write completion polling and make writes go through indirect
mode for DTR writes and let spi-mem take care of polling the SR.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
This patch depends on https://patchwork.kernel.org/patch/11355593/

 drivers/spi/spi-cadence-quadspi.c | 261 ++++++++++++++++++++++++++----
 1 file changed, 228 insertions(+), 33 deletions(-)

diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 000f01c18c87..0536566e0275 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -52,6 +52,7 @@ struct cqspi_flash_pdata {
 	u8		inst_width;
 	u8		addr_width;
 	u8		data_width;
+	bool		is_dtr;
 	u8		cs;
 	bool		registered;
 };
@@ -111,6 +112,8 @@ struct cqspi_driver_platdata {
 #define CQSPI_REG_CONFIG_CHIPSELECT_LSB		10
 #define CQSPI_REG_CONFIG_DMA_MASK		BIT(15)
 #define CQSPI_REG_CONFIG_BAUD_LSB		19
+#define CQSPI_REG_CONFIG_DTR_PROTO		BIT(24)
+#define CQSPI_REG_CONFIG_DUAL_OPCODE		BIT(30)
 #define CQSPI_REG_CONFIG_IDLE_LSB		31
 #define CQSPI_REG_CONFIG_CHIPSELECT_MASK	0xF
 #define CQSPI_REG_CONFIG_BAUD_MASK		0xF
@@ -217,6 +220,14 @@ struct cqspi_driver_platdata {
 #define CQSPI_REG_CMDWRITEDATALOWER		0xA8
 #define CQSPI_REG_CMDWRITEDATAUPPER		0xAC

+#define CQSPI_REG_POLLING_STATUS		0xB0
+#define CQSPI_REG_POLLING_STATUS_DUMMY_LSB	16
+
+#define CQSPI_REG_OP_EXT_LOWER			0xE0
+#define CQSPI_REG_OP_EXT_READ_LSB		24
+#define CQSPI_REG_OP_EXT_WRITE_LSB		16
+#define CQSPI_REG_OP_EXT_STIG_LSB		0
+
 /* Interrupt status bits */
 #define CQSPI_REG_IRQ_MODE_ERR			BIT(0)
 #define CQSPI_REG_IRQ_UNDERFLOW			BIT(1)
@@ -291,6 +302,69 @@ static unsigned int cqspi_calc_rdreg(struct cqspi_flash_pdata *f_pdata)
 	return rdreg;
 }

+static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata,
+			      const struct spi_mem_op *op)
+{
+	f_pdata->inst_width = CQSPI_INST_TYPE_SINGLE;
+	f_pdata->addr_width = CQSPI_INST_TYPE_SINGLE;
+	f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
+	f_pdata->is_dtr = op->data.is_dtr && op->cmd.is_dtr && op->addr.is_dtr;
+
+	switch (op->data.buswidth) {
+	case 0:
+		break;
+	case 1:
+		f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
+		break;
+	case 2:
+		f_pdata->data_width = CQSPI_INST_TYPE_DUAL;
+		break;
+	case 4:
+		f_pdata->data_width = CQSPI_INST_TYPE_QUAD;
+		break;
+	case 8:
+		f_pdata->data_width = CQSPI_INST_TYPE_OCTAL;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* Right now we only support 8-8-8 DTR mode. */
+	if (f_pdata->is_dtr) {
+		switch (op->cmd.buswidth) {
+		case 0:
+			break;
+		case 8:
+			f_pdata->inst_width = CQSPI_INST_TYPE_OCTAL;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		switch (op->addr.buswidth) {
+		case 0:
+			break;
+		case 8:
+			f_pdata->addr_width = CQSPI_INST_TYPE_OCTAL;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		switch (op->data.buswidth) {
+		case 0:
+			break;
+		case 8:
+			f_pdata->data_width = CQSPI_INST_TYPE_OCTAL;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
 static int cqspi_wait_idle(struct cqspi_st *cqspi)
 {
 	const unsigned int poll_idle_retry = 3;
@@ -348,6 +422,52 @@ static int cqspi_exec_flash_cmd(struct cqspi_st *cqspi, unsigned int reg)
 	return cqspi_wait_idle(cqspi);
 }

+static int cqspi_setup_opcode_ext(struct cqspi_flash_pdata *f_pdata,
+				  const struct spi_mem_op *op,
+				  unsigned int shift)
+{
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	void __iomem *reg_base = cqspi->iobase;
+	int ret;
+	unsigned int reg;
+	u8 ext;
+
+	ret = spi_mem_get_cmd_ext(op, &ext);
+	if (ret)
+		return ret;
+	reg = readl(reg_base + CQSPI_REG_OP_EXT_LOWER);
+	reg &= ~(0xff << shift);
+	reg |= ext << shift;
+	writel(reg, reg_base + CQSPI_REG_OP_EXT_LOWER);
+
+	return 0;
+}
+
+static int cqspi_enable_dtr(struct cqspi_flash_pdata *f_pdata, bool enable)
+{
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	void __iomem *reg_base = cqspi->iobase;
+	unsigned int reg;
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+
+	/*
+	 * We enable dual byte opcode here. The callers have to set up the
+	 * extension opcode based on which type of operation it is.
+	 */
+	if (enable) {
+		reg |= CQSPI_REG_CONFIG_DTR_PROTO;
+		reg |= CQSPI_REG_CONFIG_DUAL_OPCODE;
+	} else {
+		reg &= ~CQSPI_REG_CONFIG_DTR_PROTO;
+		reg &= ~CQSPI_REG_CONFIG_DUAL_OPCODE;
+	}
+
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+
+	return cqspi_wait_idle(cqspi);
+}
+
 static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata,
 			      const struct spi_mem_op *op)
 {
@@ -361,6 +481,14 @@ static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata,
 	size_t read_len;
 	int status;

+	status = cqspi_set_protocol(f_pdata, op);
+	if (status)
+		return status;
+
+	status = cqspi_enable_dtr(f_pdata, f_pdata->is_dtr);
+	if (status)
+		return status;
+
 	if (!n_rx || n_rx > CQSPI_STIG_DATA_LEN_MAX || !rxbuf) {
 		dev_err(&cqspi->pdev->dev,
 			"Invalid input argument, len %zu rxbuf 0x%p\n",
@@ -368,6 +496,14 @@ static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata,
 		return -EINVAL;
 	}

+	/* Set up the command opcode extension. */
+	if (f_pdata->is_dtr) {
+		status = cqspi_setup_opcode_ext(f_pdata, op,
+						CQSPI_REG_OP_EXT_STIG_LSB);
+		if (status)
+			return status;
+	}
+
 	reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;

 	rdreg = cqspi_calc_rdreg(f_pdata);
@@ -410,6 +546,15 @@ static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata,
 	unsigned int reg;
 	unsigned int data;
 	size_t write_len;
+	int ret;
+
+	ret = cqspi_set_protocol(f_pdata, op);
+	if (ret)
+		return ret;
+
+	ret = cqspi_enable_dtr(f_pdata, f_pdata->is_dtr);
+	if (ret)
+		return ret;

 	if (n_tx > CQSPI_STIG_DATA_LEN_MAX || (n_tx && !txbuf)) {
 		dev_err(&cqspi->pdev->dev,
@@ -418,6 +563,17 @@ static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata,
 		return -EINVAL;
 	}

+	reg = cqspi_calc_rdreg(f_pdata);
+	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
+
+	/* Set up the command opcode extension. */
+	if (f_pdata->is_dtr) {
+		ret = cqspi_setup_opcode_ext(f_pdata, op,
+					     CQSPI_REG_OP_EXT_STIG_LSB);
+		if (ret)
+			return ret;
+	}
+
 	reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;

 	if (op->addr.nbytes) {
@@ -456,16 +612,32 @@ static int cqspi_read_setup(struct cqspi_flash_pdata *f_pdata,
 	void __iomem *reg_base = cqspi->iobase;
 	unsigned int dummy_clk = 0;
 	unsigned int reg;
+	int ret;
+
+	ret = cqspi_enable_dtr(f_pdata, f_pdata->is_dtr);
+	if (ret)
+		return ret;
+
+	/* Set up the command opcode extension. */
+	if (f_pdata->is_dtr) {
+		ret = cqspi_setup_opcode_ext(f_pdata, op,
+					     CQSPI_REG_OP_EXT_READ_LSB);
+		if (ret)
+			return ret;
+	}

 	reg = op->cmd.opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB;
 	reg |= cqspi_calc_rdreg(f_pdata);

 	/* Setup dummy clock cycles */
-	dummy_clk = op->dummy.nbytes * 8;
+	dummy_clk = op->dummy.nbytes * (8 / op->dummy.buswidth);
+	if (f_pdata->is_dtr)
+		dummy_clk /= 2;
+
 	if (dummy_clk > CQSPI_DUMMY_CLKS_MAX)
 		dummy_clk = CQSPI_DUMMY_CLKS_MAX;

-	if (dummy_clk / 8)
+	if (dummy_clk)
 		reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
 		       << CQSPI_REG_RD_INSTR_DUMMY_LSB;

@@ -575,15 +747,42 @@ static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata,
 			     const struct spi_mem_op *op)
 {
 	unsigned int reg;
+	int ret;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *reg_base = cqspi->iobase;

+	ret = cqspi_enable_dtr(f_pdata, f_pdata->is_dtr);
+	if (ret)
+		return ret;
+
 	/* Set opcode. */
 	reg = op->cmd.opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB;
+	reg |= f_pdata->data_width << CQSPI_REG_WR_INSTR_TYPE_DATA_LSB;
+	reg |= f_pdata->addr_width << CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB;
 	writel(reg, reg_base + CQSPI_REG_WR_INSTR);
 	reg = cqspi_calc_rdreg(f_pdata);
 	writel(reg, reg_base + CQSPI_REG_RD_INSTR);

+	/* Set up the command opcode extension. */
+	if (f_pdata->is_dtr) {
+		ret = cqspi_setup_opcode_ext(f_pdata, op,
+					     CQSPI_REG_OP_EXT_WRITE_LSB);
+		if (ret)
+			return ret;
+
+		/*
+		 * Some flashes like the cypress Semper flash expect a 4-byte
+		 * dummy address with the Read SR command in DTR mode, but this
+		 * controller does not support sending address with the Read SR
+		 * command. So, disable write completion polling on the
+		 * controller's side. spi-nor will take care of polling the
+		 * status register.
+		 */
+		reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+		reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
+		writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+	}
+
 	reg = readl(reg_base + CQSPI_REG_SIZE);
 	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
 	reg |= (op->addr.nbytes - 1);
@@ -833,35 +1032,6 @@ static void cqspi_configure(struct cqspi_flash_pdata *f_pdata,
 		cqspi_controller_enable(cqspi, 1);
 }

-static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata,
-			      const struct spi_mem_op *op)
-{
-	f_pdata->inst_width = CQSPI_INST_TYPE_SINGLE;
-	f_pdata->addr_width = CQSPI_INST_TYPE_SINGLE;
-	f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
-
-	if (op->data.dir == SPI_MEM_DATA_IN) {
-		switch (op->data.buswidth) {
-		case 1:
-			f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
-			break;
-		case 2:
-			f_pdata->data_width = CQSPI_INST_TYPE_DUAL;
-			break;
-		case 4:
-			f_pdata->data_width = CQSPI_INST_TYPE_QUAD;
-			break;
-		case 8:
-			f_pdata->data_width = CQSPI_INST_TYPE_OCTAL;
-			break;
-		default:
-			return -EINVAL;
-		}
-	}
-
-	return 0;
-}
-
 static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata,
 			   const struct spi_mem_op *op)
 {
@@ -879,7 +1049,16 @@ static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata,
 	if (ret)
 		return ret;

-	if (cqspi->use_dac_mode && ((to + len) <= cqspi->ahb_size)) {
+	/*
+	 * Some flashes like the Cypress Semper flash expect a dummy 4-byte
+	 * address (all 0s) with the read status register command in DTR mode.
+	 * But this controller does not support sending dummy address bytes to
+	 * the flash when it is polling the write completion register in DTR
+	 * mode. So, we can not use direct mode when in DTR mode for writing
+	 * data.
+	 */
+	if (!f_pdata->is_dtr && cqspi->use_dac_mode
+	    && ((to + len) <= cqspi->ahb_size)) {
 		memcpy_toio(cqspi->ahb_base + to, buf, len);
 		return cqspi_wait_idle(cqspi);
 	}
@@ -1006,6 +1185,20 @@ static int cqspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
 	return ret;
 }

+static bool cqspi_supports_mem_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op)
+{
+	bool all_true, all_false;
+
+	all_true = op->cmd.is_dtr && op->addr.is_dtr && op->dummy.is_dtr &&
+		   op->data.is_dtr;
+	all_false = !op->cmd.is_dtr && !op->addr.is_dtr && !op->dummy.is_dtr &&
+		    !op->data.is_dtr;
+
+	/* Mixed DTR modes not supported. */
+	return all_true || all_false;
+}
+
 static int cqspi_of_get_flash_pdata(struct platform_device *pdev,
 				    struct cqspi_flash_pdata *f_pdata,
 				    struct device_node *np)
@@ -1136,6 +1329,7 @@ static int cqspi_request_mmap_dma(struct cqspi_st *cqspi)

 static const struct spi_controller_mem_ops cqspi_mem_ops = {
 	.exec_op = cqspi_exec_mem_op,
+	.supports_op = cqspi_supports_mem_op,
 };

 static int cqspi_setup_flash(struct cqspi_st *cqspi)
@@ -1187,7 +1381,8 @@ static int cqspi_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "spi_alloc_master failed\n");
 		return -ENOMEM;
 	}
-	master->mode_bits = SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL;
+	master->mode_bits = SPI_RX_OCTAL | SPI_TX_OCTAL | SPI_RX_QUAD |
+			    SPI_TX_DUAL | SPI_RX_DUAL | SPI_RX_DTR | SPI_TX_DTR;
 	master->mem_ops = &cqspi_mem_ops;
 	master->dev.of_node = pdev->dev.of_node;

--
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 4/9] mtd: spi-nor: add support for DTR protocol
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
                   ` (2 preceding siblings ...)
  2020-02-11 13:33 ` [PATCH 3/9] spi: cadence-quadspi: Add support for octal DTR flashes Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 5/9] mtd: spi-nor: get command opcode extension type from BFPT Pratyush Yadav
                   ` (4 subsequent siblings)
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.

Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 245 ++++++++++++++++++++++++++--------
 include/linux/mtd/spi-nor.h   |  34 +++--
 2 files changed, 213 insertions(+), 66 deletions(-)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 4fc632ec18fe..371e56f3cdab 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -238,6 +238,7 @@ struct flash_info {
 					 * status register. Must be used with
 					 * SPI_NOR_HAS_TB.
 					 */
+#define SPI_NOR_OCTAL_DTR_READ	BIT(18)	/* Flash supports octal DTR Read. */
 
 	/* Part specific fixup hooks. */
 	const struct spi_nor_fixups *fixups;
@@ -245,6 +246,46 @@ struct flash_info {
 
 #define JEDEC_MFR(info)	((info)->id[0])
 
+/**
+ * spi_nor_spimem_setup_op() - Set up common properties of a spi-mem op.
+ * @nor:		pointer to a 'struct spi_nor'
+ * @op:			pointer to the 'struct spi_mem_op' whose properties
+ *			need to be initialized.
+ * @proto:		the protocol from which the properties need to be set.
+ */
+static void spi_nor_spimem_setup_op(const struct spi_nor *nor,
+				    struct spi_mem_op *op,
+				    const enum spi_nor_protocol proto)
+{
+
+	op->cmd.buswidth = spi_nor_get_protocol_inst_nbits(proto);
+
+	if (op->addr.nbytes)
+		op->addr.buswidth = spi_nor_get_protocol_addr_nbits(proto);
+
+	if (op->dummy.nbytes)
+		op->dummy.buswidth = spi_nor_get_protocol_addr_nbits(proto);
+
+	if (op->data.buf.in || op->data.buf.out)
+		op->data.buswidth = spi_nor_get_protocol_data_nbits(proto);
+
+	if (spi_nor_protocol_is_dtr(proto)) {
+		/*
+		 * spi-mem supports mixed DTR modes, but right now we can only
+		 * have all phases either DTR or STR. IOW, spi-mem can have
+		 * something like 4S-4D-4D, but spi-nor can't. So, set all 4
+		 * phases to either DTR or STR.
+		 */
+		op->cmd.is_dtr = op->addr.is_dtr = op->dummy.is_dtr
+			       = op->data.is_dtr = true;
+
+		/* 2 bytes per clock cycle in DTR mode. */
+		op->dummy.nbytes *= 2;
+
+		op->cmd.ext_type = nor->cmd_ext;
+	}
+}
+
 /**
  * spi_nor_spimem_xfer_data() - helper function to read/write data to
  *                              flash's memory region
@@ -316,14 +357,12 @@ static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from,
 			   SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
 			   SPI_MEM_OP_DATA_IN(len, buf, 1));
 
-	/* get transfer protocols. */
-	op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
-	op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
-	op.dummy.buswidth = op.addr.buswidth;
-	op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+	spi_nor_spimem_setup_op(nor, &op, nor->read_proto);
 
 	/* convert the dummy cycles to the number of bytes */
 	op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+	if (spi_nor_protocol_is_dtr(nor->read_proto))
+		op.dummy.nbytes *= 2;
 
 	return spi_nor_spimem_xfer_data(nor, &op);
 }
@@ -365,13 +404,11 @@ static ssize_t spi_nor_spimem_write_data(struct spi_nor *nor, loff_t to,
 			   SPI_MEM_OP_NO_DUMMY,
 			   SPI_MEM_OP_DATA_OUT(len, buf, 1));
 
-	op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
-	op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
-	op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
-
 	if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
 		op.addr.nbytes = 0;
 
+	spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+
 	return spi_nor_spimem_xfer_data(nor, &op);
 }
 
@@ -410,10 +447,16 @@ static int spi_nor_write_enable(struct spi_nor *nor)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_WREN,
-						     NULL, 0);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_WREN,
+							     NULL, 0);
 	}
 
 	if (ret)
@@ -439,10 +482,16 @@ static int spi_nor_write_disable(struct spi_nor *nor)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_WRDI,
-						     NULL, 0);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_WRDI,
+							     NULL, 0);
 	}
 
 	if (ret)
@@ -501,10 +550,15 @@ static int spi_nor_read_fsr(struct spi_nor *nor, u8 *fsr)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_IN(1, fsr, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDFSR,
-						    fsr, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDFSR,
+							    fsr, 1);
 	}
 
 	if (ret)
@@ -533,9 +587,15 @@ static int spi_nor_read_cr(struct spi_nor *nor, u8 *cr)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_IN(1, cr, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDCR, cr, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDCR,
+							    cr, 1);
 	}
 
 	if (ret)
@@ -566,12 +626,17 @@ static int macronix_set_4byte(struct spi_nor *nor, bool enable)
 				  SPI_MEM_OP_NO_DUMMY,
 				  SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor,
-						     enable ? SPINOR_OP_EN4B :
-							      SPINOR_OP_EX4B,
-						     NULL, 0);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+						enable ? SPINOR_OP_EN4B :
+							 SPINOR_OP_EX4B,
+						NULL, 0);
 	}
 
 	if (ret)
@@ -624,10 +689,15 @@ static int spansion_set_4byte(struct spi_nor *nor, bool enable)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_BRWR,
-						     nor->bouncebuf, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor, SPINOR_OP_BRWR,
+							     nor->bouncebuf, 1);
 	}
 
 	if (ret)
@@ -656,10 +726,16 @@ static int spi_nor_write_ear(struct spi_nor *nor, u8 ear)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_WREAR,
-						     nor->bouncebuf, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_WREAR,
+							     nor->bouncebuf, 1);
 	}
 
 	if (ret)
@@ -719,10 +795,16 @@ static int spi_nor_xread_sr(struct spi_nor *nor, u8 *sr)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_IN(1, sr, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->read_reg(nor, SPINOR_OP_XRDSR,
-						    sr, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->read_reg(nor,
+							    SPINOR_OP_XRDSR,
+							    sr, 1);
 	}
 
 	if (ret)
@@ -764,10 +846,16 @@ static void spi_nor_clear_sr(struct spi_nor *nor)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_CLSR,
-						     NULL, 0);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_CLSR,
+							     NULL, 0);
 	}
 
 	if (ret)
@@ -817,10 +905,16 @@ static void spi_nor_clear_fsr(struct spi_nor *nor)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_CLFSR,
-						     NULL, 0);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_CLFSR,
+							     NULL, 0);
 	}
 
 	if (ret)
@@ -950,10 +1044,16 @@ static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_OUT(len, sr, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_WRSR,
-						     sr, len);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_WRSR,
+							     sr, len);
 	}
 
 	if (ret) {
@@ -1152,10 +1252,16 @@ static int spi_nor_write_sr2(struct spi_nor *nor, const u8 *sr2)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_OUT(1, sr2, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_WRSR2,
-						     sr2, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_WRSR2,
+							     sr2, 1);
 	}
 
 	if (ret) {
@@ -1186,10 +1292,16 @@ static int spi_nor_read_sr2(struct spi_nor *nor, u8 *sr2)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_IN(1, sr2, 1));
 
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDSR2,
-						    sr2, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->read_reg(nor,
+							    SPINOR_OP_RDSR2,
+							    sr2, 1);
 	}
 
 	if (ret)
@@ -1217,10 +1329,16 @@ static int spi_nor_erase_chip(struct spi_nor *nor)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->write_reg(nor, SPINOR_OP_CHIP_ERASE,
-						     NULL, 0);
+		if (spi_nor_protocol_is_dtr(nor->write_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->write_reg(nor,
+							     SPINOR_OP_CHIP_ERASE,
+							     NULL, 0);
 	}
 
 	if (ret)
@@ -1379,7 +1497,11 @@ static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
+		spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+
 		return spi_mem_exec_op(nor->spimem, &op);
+	} else if (spi_nor_protocol_is_dtr(nor->write_proto)) {
+		return -ENOTSUPP;
 	} else if (nor->controller_ops->erase) {
 		return nor->controller_ops->erase(nor, addr);
 	}
@@ -3045,6 +3167,7 @@ static int spi_nor_hwcaps_read2cmd(u32 hwcaps)
 		{ SNOR_HWCAPS_READ_1_8_8,	SNOR_CMD_READ_1_8_8 },
 		{ SNOR_HWCAPS_READ_8_8_8,	SNOR_CMD_READ_8_8_8 },
 		{ SNOR_HWCAPS_READ_1_8_8_DTR,	SNOR_CMD_READ_1_8_8_DTR },
+		{ SNOR_HWCAPS_READ_8_8_8_DTR,	SNOR_CMD_READ_8_8_8_DTR },
 	};
 
 	return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd,
@@ -3061,6 +3184,7 @@ static int spi_nor_hwcaps_pp2cmd(u32 hwcaps)
 		{ SNOR_HWCAPS_PP_1_1_8,		SNOR_CMD_PP_1_1_8 },
 		{ SNOR_HWCAPS_PP_1_8_8,		SNOR_CMD_PP_1_8_8 },
 		{ SNOR_HWCAPS_PP_8_8_8,		SNOR_CMD_PP_8_8_8 },
+		{ SNOR_HWCAPS_PP_8_8_8_DTR,	SNOR_CMD_PP_8_8_8_DTR },
 	};
 
 	return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd,
@@ -3184,13 +3308,11 @@ static int spi_nor_spimem_check_readop(struct spi_nor *nor,
 					  SPI_MEM_OP_DUMMY(0, 1),
 					  SPI_MEM_OP_DATA_IN(0, NULL, 1));
 
-	op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(read->proto);
-	op.addr.buswidth = spi_nor_get_protocol_addr_nbits(read->proto);
-	op.data.buswidth = spi_nor_get_protocol_data_nbits(read->proto);
-	op.dummy.buswidth = op.addr.buswidth;
 	op.dummy.nbytes = (read->num_mode_clocks + read->num_wait_states) *
 			  op.dummy.buswidth / 8;
 
+	spi_nor_spimem_setup_op(nor, &op, nor->read_proto);
+
 	return spi_nor_spimem_check_op(nor, &op);
 }
 
@@ -3210,9 +3332,7 @@ static int spi_nor_spimem_check_pp(struct spi_nor *nor,
 					  SPI_MEM_OP_NO_DUMMY,
 					  SPI_MEM_OP_DATA_OUT(0, NULL, 1));
 
-	op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(pp->proto);
-	op.addr.buswidth = spi_nor_get_protocol_addr_nbits(pp->proto);
-	op.data.buswidth = spi_nor_get_protocol_data_nbits(pp->proto);
+	spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
 
 	return spi_nor_spimem_check_op(nor, &op);
 }
@@ -3230,11 +3350,10 @@ spi_nor_spimem_adjust_hwcaps(struct spi_nor *nor, u32 *hwcaps)
 	struct spi_nor_flash_parameter *params =  &nor->params;
 	unsigned int cap;
 
-	/* DTR modes are not supported yet, mask them all. */
-	*hwcaps &= ~SNOR_HWCAPS_DTR;
-
-	/* X-X-X modes are not supported yet, mask them all. */
-	*hwcaps &= ~SNOR_HWCAPS_X_X_X;
+	/* 2-2-2 and 4-4-4 modes are not supported yet, mask them all. */
+	*hwcaps &= ~(SNOR_HWCAPS_READ_2_2_2 |	\
+		     SNOR_HWCAPS_READ_4_4_4 |	\
+		     SNOR_HWCAPS_PP_4_4_4);
 
 	for (cap = 0; cap < sizeof(*hwcaps) * BITS_PER_BYTE; cap++) {
 		int rdidx, ppidx;
@@ -4240,9 +4359,16 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
 	}
 
 	/* 4BAIT is the only SFDP table that indicates page program support. */
-	if (pp_hwcaps & SNOR_HWCAPS_PP)
+	if (pp_hwcaps & SNOR_HWCAPS_PP) {
 		spi_nor_set_pp_settings(&params_pp[SNOR_CMD_PP],
 					SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
+		/*
+		 * Since xSPI Page Program opcode is backward compatible with
+		 * Legacy SPI, use Legacy SPI opcode there as well.
+		 */
+		spi_nor_set_pp_settings(&params_pp[SNOR_CMD_PP_8_8_8_DTR],
+					SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
+	}
 	if (pp_hwcaps & SNOR_HWCAPS_PP_1_1_4)
 		spi_nor_set_pp_settings(&params_pp[SNOR_CMD_PP_1_1_4],
 					SPINOR_OP_PP_1_1_4_4B,
@@ -4797,6 +4923,13 @@ static void spi_nor_info_init_params(struct spi_nor *nor)
 	spi_nor_set_pp_settings(&params->page_programs[SNOR_CMD_PP],
 				SPINOR_OP_PP, SNOR_PROTO_1_1_1);
 
+	/*
+	 * Since xSPI Page Program opcode is backward compatible with
+	 * Legacy SPI, use Legacy SPI opcode there as well.
+	 */
+	spi_nor_set_pp_settings(&params->page_programs[SNOR_CMD_PP_8_8_8_DTR],
+				SPINOR_OP_PP, SNOR_PROTO_8_8_8_DTR);
+
 	/*
 	 * Sector Erase settings. Sort Erase Types in ascending order, with the
 	 * smallest erase size starting at BIT(0).
@@ -4924,7 +5057,8 @@ static void spi_nor_init_params(struct spi_nor *nor)
 
 	spi_nor_manufacturer_init_params(nor);
 
-	if ((nor->info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)) &&
+	if ((nor->info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+				 SPI_NOR_OCTAL_READ | SPI_NOR_OCTAL_DTR_READ)) &&
 	    !(nor->info->flags & SPI_NOR_SKIP_SFDP))
 		spi_nor_sfdp_init_params(nor);
 
@@ -4984,7 +5118,9 @@ static int spi_nor_init(struct spi_nor *nor)
 		return err;
 	}
 
-	if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES)) {
+	if (nor->addr_width == 4 &&
+	    !(nor->info->flags & SPI_NOR_OCTAL_DTR_READ) &&
+	    !(nor->flags & SNOR_F_4B_OPCODES)) {
 		/*
 		 * If the RESET# pin isn't hooked up properly, or the system
 		 * otherwise doesn't perform a reset command in the boot
@@ -5038,6 +5174,9 @@ static int spi_nor_set_addr_width(struct spi_nor *nor)
 {
 	if (nor->addr_width) {
 		/* already configured from SFDP */
+	} else if (spi_nor_protocol_is_dtr(nor->read_proto)) {
+		 /* Always use 4-byte addresses in DTR mode. */
+		nor->addr_width = 4;
 	} else if (nor->info->addr_width) {
 		nor->addr_width = nor->info->addr_width;
 	} else if (nor->mtd.size > 0x1000000) {
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 5abd91cc6dfa..364f37276d78 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -195,6 +195,7 @@ enum spi_nor_protocol {
 	SNOR_PROTO_1_2_2_DTR = SNOR_PROTO_DTR(1, 2, 2),
 	SNOR_PROTO_1_4_4_DTR = SNOR_PROTO_DTR(1, 4, 4),
 	SNOR_PROTO_1_8_8_DTR = SNOR_PROTO_DTR(1, 8, 8),
+	SNOR_PROTO_8_8_8_DTR = SNOR_PROTO_DTR(8, 8, 8),
 };
 
 static inline bool spi_nor_protocol_is_dtr(enum spi_nor_protocol proto)
@@ -345,7 +346,7 @@ struct spi_nor_hwcaps {
  * then Quad SPI protocols before Dual SPI protocols, Fast Read and lastly
  * (Slow) Read.
  */
-#define SNOR_HWCAPS_READ_MASK		GENMASK(14, 0)
+#define SNOR_HWCAPS_READ_MASK		GENMASK(15, 0)
 #define SNOR_HWCAPS_READ		BIT(0)
 #define SNOR_HWCAPS_READ_FAST		BIT(1)
 #define SNOR_HWCAPS_READ_1_1_1_DTR	BIT(2)
@@ -362,11 +363,12 @@ struct spi_nor_hwcaps {
 #define SNOR_HWCAPS_READ_4_4_4		BIT(9)
 #define SNOR_HWCAPS_READ_1_4_4_DTR	BIT(10)
 
-#define SNOR_HWCAPS_READ_OCTAL		GENMASK(14, 11)
+#define SNOR_HWCAPS_READ_OCTAL		GENMASK(15, 11)
 #define SNOR_HWCAPS_READ_1_1_8		BIT(11)
 #define SNOR_HWCAPS_READ_1_8_8		BIT(12)
 #define SNOR_HWCAPS_READ_8_8_8		BIT(13)
 #define SNOR_HWCAPS_READ_1_8_8_DTR	BIT(14)
+#define SNOR_HWCAPS_READ_8_8_8_DTR	BIT(15)
 
 /*
  * Page Program capabilities.
@@ -377,18 +379,19 @@ struct spi_nor_hwcaps {
  * JEDEC/SFDP standard to define them. Also at this moment no SPI flash memory
  * implements such commands.
  */
-#define SNOR_HWCAPS_PP_MASK	GENMASK(22, 16)
-#define SNOR_HWCAPS_PP		BIT(16)
+#define SNOR_HWCAPS_PP_MASK		GENMASK(23, 16)
+#define SNOR_HWCAPS_PP			BIT(16)
 
-#define SNOR_HWCAPS_PP_QUAD	GENMASK(19, 17)
-#define SNOR_HWCAPS_PP_1_1_4	BIT(17)
-#define SNOR_HWCAPS_PP_1_4_4	BIT(18)
-#define SNOR_HWCAPS_PP_4_4_4	BIT(19)
+#define SNOR_HWCAPS_PP_QUAD		GENMASK(19, 17)
+#define SNOR_HWCAPS_PP_1_1_4		BIT(17)
+#define SNOR_HWCAPS_PP_1_4_4		BIT(18)
+#define SNOR_HWCAPS_PP_4_4_4		BIT(19)
 
-#define SNOR_HWCAPS_PP_OCTAL	GENMASK(22, 20)
-#define SNOR_HWCAPS_PP_1_1_8	BIT(20)
-#define SNOR_HWCAPS_PP_1_8_8	BIT(21)
-#define SNOR_HWCAPS_PP_8_8_8	BIT(22)
+#define SNOR_HWCAPS_PP_OCTAL		GENMASK(23, 20)
+#define SNOR_HWCAPS_PP_1_1_8		BIT(20)
+#define SNOR_HWCAPS_PP_1_8_8		BIT(21)
+#define SNOR_HWCAPS_PP_8_8_8		BIT(22)
+#define SNOR_HWCAPS_PP_8_8_8_DTR	BIT(23)
 
 #define SNOR_HWCAPS_X_X_X	(SNOR_HWCAPS_READ_2_2_2 |	\
 				 SNOR_HWCAPS_READ_4_4_4 |	\
@@ -399,7 +402,8 @@ struct spi_nor_hwcaps {
 #define SNOR_HWCAPS_DTR		(SNOR_HWCAPS_READ_1_1_1_DTR |	\
 				 SNOR_HWCAPS_READ_1_2_2_DTR |	\
 				 SNOR_HWCAPS_READ_1_4_4_DTR |	\
-				 SNOR_HWCAPS_READ_1_8_8_DTR)
+				 SNOR_HWCAPS_READ_1_8_8_DTR |	\
+				 SNOR_HWCAPS_READ_8_8_8_DTR)
 
 #define SNOR_HWCAPS_ALL		(SNOR_HWCAPS_READ_MASK |	\
 				 SNOR_HWCAPS_PP_MASK)
@@ -438,6 +442,7 @@ enum spi_nor_read_command_index {
 	SNOR_CMD_READ_1_8_8,
 	SNOR_CMD_READ_8_8_8,
 	SNOR_CMD_READ_1_8_8_DTR,
+	SNOR_CMD_READ_8_8_8_DTR,
 
 	SNOR_CMD_READ_MAX
 };
@@ -454,6 +459,7 @@ enum spi_nor_pp_command_index {
 	SNOR_CMD_PP_1_1_8,
 	SNOR_CMD_PP_1_8_8,
 	SNOR_CMD_PP_8_8_8,
+	SNOR_CMD_PP_8_8_8_DTR,
 
 	SNOR_CMD_PP_MAX
 };
@@ -570,6 +576,7 @@ struct flash_info;
  * @program_opcode:	the program opcode
  * @sst_write_second:	used by the SST write operation
  * @flags:		flag options for the current SPI-NOR (SNOR_F_*)
+ * @cmd_ext:		the command opcode extension for DTR mode.
  * @read_proto:		the SPI protocol for read operations
  * @write_proto:	the SPI protocol for write operations
  * @reg_proto		the SPI protocol for read_reg/write_reg/erase operations
@@ -599,6 +606,7 @@ struct spi_nor {
 	enum spi_nor_protocol	reg_proto;
 	bool			sst_write_second;
 	u32			flags;
+	enum spi_mem_cmd_ext	cmd_ext;
 
 	const struct spi_nor_controller_ops *controller_ops;
 
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 5/9] mtd: spi-nor: get command opcode extension type from BFPT
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
                   ` (3 preceding siblings ...)
  2020-02-11 13:33 ` [PATCH 4/9] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 6/9] mtd: spi-nor: parse xSPI Profile 1.0 table Pratyush Yadav
                   ` (3 subsequent siblings)
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.

As of JESD216D.01, BFPT is 20 DWORDs, so update the table size to
reflect that.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 30 +++++++++++++++++++++++++++---
 1 file changed, 27 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 371e56f3cdab..ff0b25754939 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -79,11 +79,11 @@ struct sfdp_header {
 /* Basic Flash Parameter Table */
 
 /*
- * JESD216 rev B defines a Basic Flash Parameter Table of 16 DWORDs.
- * They are indexed from 1 but C arrays are indexed from 0.
+ * JESD216 rev D defines a Basic Flash Parameter Table of 20 DWORDs. They are
+ * indexed from 1 but C arrays are indexed from 0.
  */
 #define BFPT_DWORD(i)		((i) - 1)
-#define BFPT_DWORD_MAX		16
+#define BFPT_DWORD_MAX		20
 
 /* The first version of JESD216 defined only 9 DWORDs. */
 #define BFPT_DWORD_MAX_JESD216			9
@@ -148,6 +148,12 @@ struct sfdp_header {
 #define BFPT_DWORD15_QER_SR2_BIT1_NO_RD		(0x4UL << 20)
 #define BFPT_DWORD15_QER_SR2_BIT1		(0x5UL << 20) /* Spansion */
 
+#define BFPT_DWORD18_CMD_EXT_MASK		GENMASK(30, 29)
+#define BFPT_DWORD18_CMD_EXT_REP		(0x0UL << 29) /* Repeat */
+#define BFPT_DWORD18_CMD_EXT_INV		(0x1UL << 29) /* Invert */
+#define BFPT_DWORD18_CMD_EXT_RES		(0x2UL << 29) /* Reserved */
+#define BFPT_DWORD18_CMD_EXT_16B		(0x3UL << 29) /* 16-bit opcode */
+
 struct sfdp_bfpt {
 	u32	dwords[BFPT_DWORD_MAX];
 };
@@ -3867,6 +3873,24 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
 		return -EINVAL;
 	}
 
+	/* 8D-8D-8D command extension. */
+	switch (bfpt.dwords[BFPT_DWORD(18)] & BFPT_DWORD18_CMD_EXT_MASK) {
+	case BFPT_DWORD18_CMD_EXT_REP:
+		nor->cmd_ext = SPI_MEM_EXT_REPEAT;
+		break;
+
+	case BFPT_DWORD18_CMD_EXT_INV:
+		nor->cmd_ext = SPI_MEM_EXT_INVERT;
+		break;
+
+	case BFPT_DWORD18_CMD_EXT_RES:
+		return -EINVAL;
+
+	case BFPT_DWORD18_CMD_EXT_16B:
+		dev_err(nor->dev, "16-bit opcodes not supported\n");
+		return -ENOTSUPP;
+	}
+
 	return spi_nor_post_bfpt_fixups(nor, bfpt_header, &bfpt, params);
 }
 
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 6/9] mtd: spi-nor: parse xSPI Profile 1.0 table
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
                   ` (4 preceding siblings ...)
  2020-02-11 13:33 ` [PATCH 5/9] mtd: spi-nor: get command opcode extension type from BFPT Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 7/9] mtd: spi-nor: use dummy cycle and address width info from SFDP Pratyush Yadav
                   ` (2 subsequent siblings)
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
the number of dummy cycles needed for a Read Status Register command,
and the number of address bytes needed for a Read Status Register
command.

The default dummy cycles for a fast octal DTR read are set to 20. Since
there is no simple way of determining the dummy cycles needed for the
fast read command, flashes that use a different value should update it
in their flash-specific hooks.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 80 +++++++++++++++++++++++++++++++++++
 include/linux/mtd/spi-nor.h   |  5 +++
 2 files changed, 85 insertions(+)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index ff0b25754939..eefde5abff8a 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -16,6 +16,7 @@
 #include <linux/sizes.h>
 #include <linux/slab.h>
 #include <linux/sort.h>
+#include <linux/bitfield.h>
 
 #include <linux/mtd/mtd.h>
 #include <linux/of_platform.h>
@@ -58,12 +59,14 @@ struct sfdp_parameter_header {
 #define SFDP_BFPT_ID		0xff00	/* Basic Flash Parameter Table */
 #define SFDP_SECTOR_MAP_ID	0xff81	/* Sector Map Table */
 #define SFDP_4BAIT_ID		0xff84  /* 4-byte Address Instruction Table */
+#define SFDP_PROFILE1_ID	0xff05	/* xSPI Profile 1.0 table. */
 
 #define SFDP_SIGNATURE		0x50444653U
 #define SFDP_JESD216_MAJOR	1
 #define SFDP_JESD216_MINOR	0
 #define SFDP_JESD216A_MINOR	5
 #define SFDP_JESD216B_MINOR	6
+#define SFDP_JESD216D_MINOR	8
 
 struct sfdp_header {
 	u32		signature; /* Ox50444653U <=> "SFDP" */
@@ -158,6 +161,11 @@ struct sfdp_bfpt {
 	u32	dwords[BFPT_DWORD_MAX];
 };
 
+/* xSPI Profile 1.0 table (from JESD216D.01). */
+#define PROFILE1_DWORD1_RD_FAST_CMD		GENMASK(15, 8)
+#define PROFILE1_DWORD1_RDSR_DUMMY		BIT(28)
+#define PROFILE1_DWORD1_RDSR_ADDR_BYTES		BIT(29)
+
 /**
  * struct spi_nor_fixups - SPI NOR fixup hooks
  * @default_init: called after default flash parameters init. Used to tweak
@@ -4426,6 +4434,74 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
 	return ret;
 }
 
+/**
+ * spi_nor_parse_profile1() - parse the xSPI Profile 1.0 table
+ * @nor:		pointer to a 'struct spi_nor'
+ * @param_header:	pointer to the 'struct sfdp_parameter_header' describing
+ *			the 4-Byte Address Instruction Table length and version.
+ * @params:		pointer to the 'struct spi_nor_flash_parameter' to be.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_profile1(struct spi_nor *nor,
+				  const struct sfdp_parameter_header *profile1_header,
+				  struct spi_nor_flash_parameter *params)
+{
+	u32 *table, opcode, addr;
+	size_t len;
+	int ret, i;
+
+	len = profile1_header->length * sizeof(*table);
+	table = kmalloc(len, GFP_KERNEL);
+	if (!table)
+		return -ENOMEM;
+
+	addr = SFDP_PARAM_HEADER_PTP(profile1_header);
+	ret = spi_nor_read_sfdp(nor, addr, len, table);
+	if (ret)
+		goto out;
+
+	/* Fix endianness of the table DWORDs. */
+	for (i = 0; i < profile1_header->length; i++)
+		table[i] = le32_to_cpu(table[i]);
+
+	/* Get 8D-8D-8D fast read opcode and dummy cycles. */
+	opcode = FIELD_GET(PROFILE1_DWORD1_RD_FAST_CMD, table[0]);
+
+	/*
+	 * Update the fast read settings. We set the default dummy cycles to 20
+	 * here. Flashes can change this value if they need to when enabling
+	 * octal mode.
+	 */
+	params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+	spi_nor_set_read_settings(&params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, 20, opcode,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	/*
+	 * Since the flash supports xSPI DTR reads, it should also support DTR
+	 * Page Program opcodes.
+	 */
+	params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR;
+
+	/*
+	 * Set the Read Status Register dummy cycles and dummy address bytes.
+	 */
+	if (table[0] & PROFILE1_DWORD1_RDSR_DUMMY)
+		params->rdsr_dummy = 8;
+	else
+		params->rdsr_dummy = 4;
+
+	if (table[0] & PROFILE1_DWORD1_RDSR_ADDR_BYTES)
+		params->rdsr_addr_nbytes = 4;
+	else
+		params->rdsr_addr_nbytes = 0;
+
+out:
+	kfree(table);
+	return ret;
+}
+
 /**
  * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
  * @nor:		pointer to a 'struct spi_nor'
@@ -4527,6 +4603,10 @@ static int spi_nor_parse_sfdp(struct spi_nor *nor,
 			err = spi_nor_parse_4bait(nor, param_header, params);
 			break;
 
+		case SFDP_PROFILE1_ID:
+			err = spi_nor_parse_profile1(nor, param_header, params);
+			break;
+
 		default:
 			break;
 		}
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 364f37276d78..f54dbd0f86ab 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -515,6 +515,9 @@ struct spi_nor_locking_ops {
  *
  * @size:		the flash memory density in bytes.
  * @page_size:		the page size of the SPI NOR flash memory.
+ * @rdsr_dummy:		dummy cycles needed for Read Status Register command.
+ * @rdsr_addr_nbytes:	dummy address bytes needed for Read Status Register
+ *			command.
  * @hwcaps:		describes the read and page program hardware
  *			capabilities.
  * @reads:		read capabilities ordered by priority: the higher index
@@ -537,6 +540,8 @@ struct spi_nor_locking_ops {
 struct spi_nor_flash_parameter {
 	u64				size;
 	u32				page_size;
+	u8				rdsr_dummy;
+	u8				rdsr_addr_nbytes;
 
 	struct spi_nor_hwcaps		hwcaps;
 	struct spi_nor_read_command	reads[SNOR_CMD_READ_MAX];
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 7/9] mtd: spi-nor: use dummy cycle and address width info from SFDP
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
                   ` (5 preceding siblings ...)
  2020-02-11 13:33 ` [PATCH 6/9] mtd: spi-nor: parse xSPI Profile 1.0 table Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 8/9] mtd: spi-nor: enable octal DTR mode when possible Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash Pratyush Yadav
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in octal DTR mode.
Use that information to send the correct Read SR command.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index eefde5abff8a..8c5d7bfa4f16 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -525,6 +525,8 @@ static int spi_nor_write_disable(struct spi_nor *nor)
 static int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
 {
 	int ret;
+	u8 addr_bytes = nor->params.rdsr_addr_nbytes;
+	u8 dummy = nor->params.rdsr_dummy;
 
 	if (nor->spimem) {
 		struct spi_mem_op op =
@@ -533,10 +535,21 @@ static int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_IN(1, sr, 1));
 
+		if (spi_nor_protocol_is_dtr(nor->reg_proto)) {
+			op.addr.nbytes = addr_bytes;
+			op.addr.val = 0;
+			op.dummy.nbytes = dummy;
+		}
+
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDSR,
-						    sr, 1);
+		if (spi_nor_protocol_is_dtr(nor->reg_proto))
+			ret = -ENOTSUPP;
+		else
+			ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDSR,
+							    sr, 1);
 	}
 
 	if (ret)
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 8/9] mtd: spi-nor: enable octal DTR mode when possible
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
                   ` (6 preceding siblings ...)
  2020-02-11 13:33 ` [PATCH 7/9] mtd: spi-nor: use dummy cycle and address width info from SFDP Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-11 13:33 ` [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash Pratyush Yadav
  8 siblings, 0 replies; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 31 +++++++++++++++++++++++++++++++
 include/linux/mtd/spi-nor.h   |  2 ++
 2 files changed, 33 insertions(+)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 8c5d7bfa4f16..78e3475fa2a9 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -5184,6 +5184,31 @@ static void spi_nor_init_params(struct spi_nor *nor)
 	spi_nor_late_init_params(nor);
 }
 
+/** spi_nor_octal_dtr_enable() - enable Octal DTR I/O if needed
+ * @nor:                 pointer to a 'struct spi_nor'
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_octal_dtr_enable(struct spi_nor *nor)
+{
+	int ret;
+
+	if (!nor->params.octal_dtr_enable)
+		return 0;
+
+	if (!(spi_nor_get_protocol_width(nor->read_proto) == 8 ||
+	      spi_nor_get_protocol_width(nor->write_proto) == 8))
+		return 0;
+
+	ret = nor->params.octal_dtr_enable(nor);
+	if (ret)
+		return ret;
+
+	nor->reg_proto = SNOR_PROTO_8_8_8_DTR;
+
+	return 0;
+}
+
 /**
  * spi_nor_quad_enable() - enable Quad I/O if needed.
  * @nor:                pointer to a 'struct spi_nor'
@@ -5223,6 +5248,12 @@ static int spi_nor_init(struct spi_nor *nor)
 {
 	int err;
 
+	err = spi_nor_octal_dtr_enable(nor);
+	if (err) {
+		dev_dbg(nor->dev, "octal mode not supported\n");
+		return err;
+	}
+
 	err = spi_nor_quad_enable(nor);
 	if (err) {
 		dev_dbg(nor->dev, "quad mode not supported\n");
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index f54dbd0f86ab..c653f6713cfc 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -526,6 +526,7 @@ struct spi_nor_locking_ops {
  *                      higher index in the array, the higher priority.
  * @erase_map:		the erase map parsed from the SFDP Sector Map Parameter
  *                      Table.
+ * @octal_dtr_enable:	enables SPI NOR octal DTR mode.
  * @quad_enable:	enables SPI NOR quad mode.
  * @set_4byte:		puts the SPI NOR in 4 byte addressing mode.
  * @convert_addr:	converts an absolute address into something the flash
@@ -549,6 +550,7 @@ struct spi_nor_flash_parameter {
 
 	struct spi_nor_erase_map        erase_map;
 
+	int (*octal_dtr_enable)(struct spi_nor *nor);
 	int (*quad_enable)(struct spi_nor *nor);
 	int (*set_4byte)(struct spi_nor *nor, bool enable);
 	u32 (*convert_addr)(struct spi_nor *nor, u32 addr);
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash
  2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
                   ` (7 preceding siblings ...)
  2020-02-11 13:33 ` [PATCH 8/9] mtd: spi-nor: enable octal DTR mode when possible Pratyush Yadav
@ 2020-02-11 13:33 ` Pratyush Yadav
  2020-02-13 10:36   ` [EXT] " Kuldeep Singh
  8 siblings, 1 reply; 11+ messages in thread
From: Pratyush Yadav @ 2020-02-11 13:33 UTC (permalink / raw)
  To: Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown
  Cc: Sekhar Nori, linux-mtd, linux-kernel, Pratyush Yadav, linux-spi

The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.

The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.

The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 192 ++++++++++++++++++++++++++++++++++
 include/linux/mtd/spi-nor.h   |  14 +++
 2 files changed, 206 insertions(+)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 78e3475fa2a9..367e3d0f65aa 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -260,6 +260,12 @@ struct flash_info {
 
 #define JEDEC_MFR(info)	((info)->id[0])
 
+/* Forward declarations that will be used by s28hs512t_setup(). */
+static int spi_nor_default_setup(struct spi_nor *nor,
+				 const struct spi_nor_hwcaps *hwcaps);
+static void spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
+				    u8 opcode, enum spi_nor_protocol proto);
+
 /**
  * spi_nor_spimem_setup_op() - Set up common properties of a spi-mem op.
  * @nor:		pointer to a 'struct spi_nor'
@@ -2241,6 +2247,65 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 	return ret;
 }
 
+/**
+ * spi_nor_cypress_octal_enable() - Enable octal DTR mode on Cypress flashes.
+ * @nor:		pointer to a 'struct spi_nor'
+ *
+ * This also sets the memory access latency cycles to 20, which is the default
+ * in the spi-nor framework.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_cypress_octal_enable(struct spi_nor *nor)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	/* Use 20 dummy cycles for memory array reads. */
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_8_20;
+	op = (struct spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR2V, 1),
+			SPI_MEM_OP_NO_DUMMY,
+			SPI_MEM_OP_DATA_OUT(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev,
+			 "failed to set default memory latency value: %d\n",
+			 ret);
+		return ret;
+	}
+	ret = spi_nor_wait_till_ready(nor);
+	if (ret)
+		return ret;
+
+	nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].num_wait_states = 20;
+	nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].num_mode_clocks = 0;
+
+	/* Set the octal and DTR enable bits. */
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
+	op = (struct spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR5V, 1),
+			SPI_MEM_OP_NO_DUMMY,
+			SPI_MEM_OP_DATA_OUT(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev, "Failed to enable octal DTR mode\n");
+		return ret;
+	}
+
+	return 0;
+}
+
 /**
  * spi_nor_sr1_bit6_quad_enable() - Set the Quad Enable BIT(6) in the Status
  * Register 1.
@@ -2453,6 +2518,130 @@ static struct spi_nor_fixups gd25q256_fixups = {
 	.default_init = gd25q256_default_init,
 };
 
+static int s28hs512t_setup(struct spi_nor *nor,
+			    const struct spi_nor_hwcaps *hwcaps)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	if (!nor->spimem) {
+		dev_err(nor->dev,
+			"operation not supported for non-spimem drivers\n");
+		return -ENOTSUPP;
+	}
+
+	/*
+	 * This Cypress flash also supports hybrid sector sizes. Make sure
+	 * uniform sector mode is selected. This is done by setting the bit
+	 * CFR3N[3].
+	 */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3N, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_IN(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	/* Set the uniform sector mode bit. */
+	*buf |= SPINOR_REG_CYPRESS_CFR3N_UNISECT;
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3N, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_err(nor->dev, "Failed to change to uniform sector mode\n");
+		return ret;
+	}
+
+	ret = spi_nor_wait_till_ready(nor);
+	if (ret)
+		return ret;
+
+	return spi_nor_default_setup(nor, hwcaps);
+}
+
+static void s28hs512t_default_init(struct spi_nor *nor)
+{
+	nor->params.octal_dtr_enable = spi_nor_cypress_octal_enable;
+	nor->params.setup = s28hs512t_setup;
+}
+
+static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/*
+	 * On older versions of the flash the xSPI Profile 1.0 table has the
+	 * 8D-8D-8D Fast Read opcode as 0x00. But it actually should be 0xEE.
+	 */
+	if (nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].opcode == 0)
+		nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].opcode =
+			SPINOR_OP_CYPRESS_RD_FAST;
+
+	/* This flash is also missing the 4-byte Page Program opcode bit. */
+	spi_nor_set_pp_settings(&nor->params.page_programs[SNOR_CMD_PP],
+				SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
+	/*
+	 * Since xSPI Page Program opcode is backward compatible with
+	 * Legacy SPI, use Legacy SPI opcode there as well.
+	 */
+	spi_nor_set_pp_settings(&nor->params.page_programs[SNOR_CMD_PP_8_8_8_DTR],
+				SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
+
+	/*
+	 * The xSPI Profile 1.0 table advertises the number of additional
+	 * address bytes needed for Read Status Register command as 0 but the
+	 * actual value for that is 4.
+	 */
+	nor->params.rdsr_addr_nbytes = 4;
+}
+
+static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
+				     const struct sfdp_parameter_header *bfpt_header,
+				     const struct sfdp_bfpt *bfpt,
+				     struct spi_nor_flash_parameter *params)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	/*
+	 * The BFPT table advertises a 512B page size but the page size is
+	 * actually configurable (with the default being 256B). Read from
+	 * CFR3V[4] and set the correct size.
+	 */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_IN(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (*buf & SPINOR_REG_CYPRESS_CFR3V_PGSZ)
+		params->page_size = 512;
+	else
+		params->page_size = 256;
+
+	return 0;
+}
+
+static struct spi_nor_fixups s28hs512t_fixups = {
+	.default_init = s28hs512t_default_init,
+	.post_sfdp = s28hs512t_post_sfdp_fixup,
+	.post_bfpt = s28hs512t_post_bfpt_fixup,
+};
+
 /* NOTE: double check command sets and memory organization when you add
  * more nor chips.  This current list focusses on newer chips, which
  * have been converging on command sets which including JEDEC ID.
@@ -2715,6 +2904,9 @@ static const struct flash_info spi_nor_ids[] = {
 	{ "s25fl064l",  INFO(0x016017,      0,  64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ "s25fl128l",  INFO(0x016018,      0,  64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ "s25fl256l",  INFO(0x016019,      0,  64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+	{ "s28hs512t",  INFO(0x345b1a,      0, 256 * 1024, 256, SECT_4K | SPI_NOR_OCTAL_DTR_READ)
+		.fixups = &s28hs512t_fixups,
+	},
 
 	/* SST -- large erase sizes are "overlays", "sectors" are 4K */
 	{ "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K | SST_WRITE) },
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index c653f6713cfc..e765272fc0f4 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -150,6 +150,20 @@
 #define SR2_QUAD_EN_BIT1	BIT(1)
 #define SR2_QUAD_EN_BIT7	BIT(7)
 
+/* For Cypress flash. */
+#define SPINOR_OP_RD_ANY_REG			0x65	/* Read any register */
+#define SPINOR_OP_WR_ANY_REG			0x71	/* Write any register */
+#define SPINOR_REG_CYPRESS_CFR2V		0x00800003
+#define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_8_20	0x8
+#define SPINOR_REG_CYPRESS_CFR3N		0x00000004
+#define SPINOR_REG_CYPRESS_CFR3V		0x00800004
+#define SPINOR_REG_CYPRESS_CFR3V_PGSZ		BIT(4) /* Page size. */
+#define SPINOR_REG_CYPRESS_CFR3N_UNISECT	BIT(3) /* Uniform sector mode */
+#define SPINOR_REG_CYPRESS_CFR4V		0x00800005
+#define SPINOR_REG_CYPRESS_CFR5V		0x00800006
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN	0x3
+#define SPINOR_OP_CYPRESS_RD_FAST		0xee
+
 /* Supported SPI protocols */
 #define SNOR_PROTO_INST_MASK	GENMASK(23, 16)
 #define SNOR_PROTO_INST_SHIFT	16
-- 
2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

* RE: [EXT] [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash
  2020-02-11 13:33 ` [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash Pratyush Yadav
@ 2020-02-13 10:36   ` " Kuldeep Singh
  0 siblings, 0 replies; 11+ messages in thread
From: Kuldeep Singh @ 2020-02-13 10:36 UTC (permalink / raw)
  To: Pratyush Yadav, Tudor Ambarus, Miquel Raynal, Richard Weinberger,
	Vignesh Raghavendra, Mark Brown, alexander.sverdlin
  Cc: Sekhar Nori, linux-mtd, linux-kernel, linux-spi

+Alexander

Hi Tudor, Vignesh, Pratyush,

> -----Original Message-----
> From: linux-kernel-owner@vger.kernel.org <linux-kernel-
> owner@vger.kernel.org> On Behalf Of Pratyush Yadav
> Sent: Tuesday, February 11, 2020 7:04 PM
> To: Tudor Ambarus <tudor.ambarus@microchip.com>; Miquel Raynal
> <miquel.raynal@bootlin.com>; Richard Weinberger <richard@nod.at>;
> Vignesh Raghavendra <vigneshr@ti.com>; Mark Brown
> <broonie@kernel.org>
> Cc: linux-mtd@lists.infradead.org; linux-kernel@vger.kernel.org; linux-
> spi@vger.kernel.org; Sekhar Nori <nsekhar@ti.com>; Pratyush Yadav
> <p.yadav@ti.com>
> Subject: [EXT] [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper
> flash
> 
> Caution: EXT Email
> 
> The Cypress Semper flash is an xSPI compliant octal DTR flash. Add support
> for using it in octal DTR mode.
> 
> The flash by default boots in a hybrid sector mode. Switch to uniform sector
> mode on boot. Use the default 20 dummy cycles for a read fast command.
> 
> The SFDP programming on some older versions of the flash was incorrect.
> Fixes for that are included in the fixup hooks.
> 
> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> ---
>  drivers/mtd/spi-nor/spi-nor.c | 192
> ++++++++++++++++++++++++++++++++++
>  include/linux/mtd/spi-nor.h   |  14 +++
>  2 files changed, 206 insertions(+)
> 
> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> index 78e3475fa2a9..367e3d0f65aa 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c
> @@ -260,6 +260,12 @@ struct flash_info {
> 
>  #define JEDEC_MFR(info)        ((info)->id[0])
> 
> +/* Forward declarations that will be used by s28hs512t_setup(). */
> +static int spi_nor_default_setup(struct spi_nor *nor,
> +                                const struct spi_nor_hwcaps *hwcaps);
> +static void spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
> +                                   u8 opcode, enum spi_nor_protocol
> +proto);
> +
>  /**
>   * spi_nor_spimem_setup_op() - Set up common properties of a spi-mem
> op.
>   * @nor:               pointer to a 'struct spi_nor'
> @@ -2241,6 +2247,65 @@ static int spi_nor_is_locked(struct mtd_info
> *mtd, loff_t ofs, uint64_t len)
>         return ret;
>  }
> 
> +/**
> + * spi_nor_cypress_octal_enable() - Enable octal DTR mode on Cypress
> flashes.
> + * @nor:               pointer to a 'struct spi_nor'
> + *
> + * This also sets the memory access latency cycles to 20, which is the
> +default
> + * in the spi-nor framework.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +static int spi_nor_cypress_octal_enable(struct spi_nor *nor) {
> +       struct spi_mem_op op;
> +       u8 *buf = nor->bouncebuf;
> +       u8 addr_width = 3;
> +       int ret;
> +
> +       /* Use 20 dummy cycles for memory array reads. */
> +       ret = spi_nor_write_enable(nor);
> +       if (ret)
> +               return ret;
> +
> +       *buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_8_20;
> +       op = (struct
> spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG,
> 1),
> +                       SPI_MEM_OP_ADDR(addr_width,
> SPINOR_REG_CYPRESS_CFR2V, 1),
> +                       SPI_MEM_OP_NO_DUMMY,
> +                       SPI_MEM_OP_DATA_OUT(1, buf, 1));
> +       ret = spi_mem_exec_op(nor->spimem, &op);
> +       if (ret) {
> +               dev_warn(nor->dev,
> +                        "failed to set default memory latency value: %d\n",
> +                        ret);
> +               return ret;
> +       }
> +       ret = spi_nor_wait_till_ready(nor);
> +       if (ret)
> +               return ret;
> +
> +       nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].num_wait_states
> = 20;
> +       nor-
> >params.reads[SNOR_CMD_READ_8_8_8_DTR].num_mode_clocks = 0;
> +
> +       /* Set the octal and DTR enable bits. */
> +       ret = spi_nor_write_enable(nor);
> +       if (ret)
> +               return ret;
> +
> +       *buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
> +       op = (struct
> spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG,
> 1),
> +                       SPI_MEM_OP_ADDR(addr_width,
> SPINOR_REG_CYPRESS_CFR5V, 1),
> +                       SPI_MEM_OP_NO_DUMMY,
> +                       SPI_MEM_OP_DATA_OUT(1, buf, 1));
> +       ret = spi_mem_exec_op(nor->spimem, &op);
> +       if (ret) {
> +               dev_warn(nor->dev, "Failed to enable octal DTR mode\n");
> +               return ret;
> +       }
> +
> +       return 0;
> +}
> +
>  /**
>   * spi_nor_sr1_bit6_quad_enable() - Set the Quad Enable BIT(6) in the
> Status
>   * Register 1.
> @@ -2453,6 +2518,130 @@ static struct spi_nor_fixups gd25q256_fixups =
> {
>         .default_init = gd25q256_default_init,  };
> 
> +static int s28hs512t_setup(struct spi_nor *nor,
> +                           const struct spi_nor_hwcaps *hwcaps) {
> +       struct spi_mem_op op;
> +       u8 *buf = nor->bouncebuf;
> +       u8 addr_width = 3;
> +       int ret;
> +
> +       if (!nor->spimem) {
> +               dev_err(nor->dev,
> +                       "operation not supported for non-spimem drivers\n");
> +               return -ENOTSUPP;
> +       }
> +
> +       /*
> +        * This Cypress flash also supports hybrid sector sizes. Make sure
> +        * uniform sector mode is selected. This is done by setting the bit
> +        * CFR3N[3].
> +        */
> +       op = (struct spi_mem_op)
> +               SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
> +                          SPI_MEM_OP_ADDR(addr_width,
> SPINOR_REG_CYPRESS_CFR3N, 1),
> +                          SPI_MEM_OP_NO_DUMMY,
> +                          SPI_MEM_OP_DATA_IN(1, buf, 1));
> +       ret = spi_mem_exec_op(nor->spimem, &op);
> +       if (ret)
> +               return ret;
> +
> +       ret = spi_nor_write_enable(nor);
> +       if (ret)
> +               return ret;
> +
> +       /* Set the uniform sector mode bit. */
> +       *buf |= SPINOR_REG_CYPRESS_CFR3N_UNISECT;
> +       op = (struct spi_mem_op)
> +               SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
> +                          SPI_MEM_OP_ADDR(addr_width,
> SPINOR_REG_CYPRESS_CFR3N, 1),
> +                          SPI_MEM_OP_NO_DUMMY,
> +                          SPI_MEM_OP_DATA_OUT(1, buf, 1));
> +       ret = spi_mem_exec_op(nor->spimem, &op);
> +       if (ret) {
> +               dev_err(nor->dev, "Failed to change to uniform sector mode\n");
> +               return ret;
> +       }
> +
> +       ret = spi_nor_wait_till_ready(nor);
> +       if (ret)
> +               return ret;
> +
> +       return spi_nor_default_setup(nor, hwcaps); }
> +
> +static void s28hs512t_default_init(struct spi_nor *nor) {
> +       nor->params.octal_dtr_enable = spi_nor_cypress_octal_enable;
> +       nor->params.setup = s28hs512t_setup; }
> +
> +static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor) {
> +       /*
> +        * On older versions of the flash the xSPI Profile 1.0 table has the
> +        * 8D-8D-8D Fast Read opcode as 0x00. But it actually should be 0xEE.
> +        */
> +       if (nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].opcode == 0)
> +               nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].opcode =
> +                       SPINOR_OP_CYPRESS_RD_FAST;
> +
> +       /* This flash is also missing the 4-byte Page Program opcode bit. */
> +       spi_nor_set_pp_settings(&nor-
> >params.page_programs[SNOR_CMD_PP],
> +                               SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
> +       /*
> +        * Since xSPI Page Program opcode is backward compatible with
> +        * Legacy SPI, use Legacy SPI opcode there as well.
> +        */
> +       spi_nor_set_pp_settings(&nor-
> >params.page_programs[SNOR_CMD_PP_8_8_8_DTR],
> +                               SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
> +
> +       /*
> +        * The xSPI Profile 1.0 table advertises the number of additional
> +        * address bytes needed for Read Status Register command as 0 but
> the
> +        * actual value for that is 4.
> +        */
> +       nor->params.rdsr_addr_nbytes = 4; }
> +
> +static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
> +                                    const struct sfdp_parameter_header *bfpt_header,
> +                                    const struct sfdp_bfpt *bfpt,
> +                                    struct spi_nor_flash_parameter
> +*params) {
> +       struct spi_mem_op op;
> +       u8 *buf = nor->bouncebuf;
> +       u8 addr_width = 3;
> +       int ret;
> +
> +       /*
> +        * The BFPT table advertises a 512B page size but the page size is
> +        * actually configurable (with the default being 256B). Read from
> +        * CFR3V[4] and set the correct size.
> +        */
> +       op = (struct spi_mem_op)
> +               SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
> +                          SPI_MEM_OP_ADDR(addr_width,
> SPINOR_REG_CYPRESS_CFR3V, 1),
> +                          SPI_MEM_OP_NO_DUMMY,
> +                          SPI_MEM_OP_DATA_IN(1, buf, 1));
> +       ret = spi_mem_exec_op(nor->spimem, &op);
> +       if (ret)
> +               return ret;
> +
> +       if (*buf & SPINOR_REG_CYPRESS_CFR3V_PGSZ)
> +               params->page_size = 512;
> +       else
> +               params->page_size = 256;
> +
> +       return 0;
> +}
> +
> +static struct spi_nor_fixups s28hs512t_fixups = {
> +       .default_init = s28hs512t_default_init,
> +       .post_sfdp = s28hs512t_post_sfdp_fixup,
> +       .post_bfpt = s28hs512t_post_bfpt_fixup, };

As of now, s25fs512s flash also require post_bfpt_fixup proposed in this patch.
On other thread[1], Alexander was also trying to resolve the same issue.
Since s28hs512t is a hyperflash and require other fixups compared to s25fs512s flash. I have a suggestion to make.

Let's make s28hs512t_ post_bfpt_fixup more generic "spansion_post_bfpt_fixup" and use that fixup for s25fs512s.
A generic name will be better as this bfpt_fixup is needed for other spansion flashes as well and not only for s28hs512t.
Please let me know your views.

Also, please see proposed diff output on top of this patch.

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index b557c67..75da26c 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -2455,7 +2455,7 @@ static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor)
        nor->params.rdsr_addr_nbytes = 4;
 }
 
-static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
+static int spansion_post_bfpt_fixup(struct spi_nor *nor,
                                     const struct sfdp_parameter_header *bfpt_header,
                                     const struct sfdp_bfpt *bfpt,
                                     struct spi_nor_flash_parameter *params)
@@ -2490,7 +2490,11 @@ static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
 static struct spi_nor_fixups s28hs512t_fixups = {
        .default_init = s28hs512t_default_init,
        .post_sfdp = s28hs512t_post_sfdp_fixup,
-       .post_bfpt = s28hs512t_post_bfpt_fixup,
+       .post_bfpt = spansion_post_bfpt_fixup,
+};
+
+static struct spi_nor_fixups s25fs512s_fixups = {
+       .post_bfpt = spansion_post_bfpt_fixup,
 };
 
 /* NOTE: double check command sets and memory organization when you add
@@ -2732,7 +2736,8 @@ static const struct flash_info spi_nor_ids[] = {
        { "s25fl512s",  INFO6(0x010220, 0x4d0080, 256 * 1024, 256,
                        SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
                        SPI_NOR_HAS_LOCK | USE_CLSR) },
-       { "s25fs512s",  INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+       { "s25fs512s",  INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR)
+                       .fixups = &s25fs512s_fixups, },
        { "s70fl01gs",  INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) },
        { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024,  64, 0) },
        { "s25sl12801", INFO(0x012018, 0x0301,  64 * 1024, 256, 0) },

Thanks 
Kuldeep

[1] https://patchwork.ozlabs.org/patch/1233915/

> +
>  /* NOTE: double check command sets and memory organization when you
> add
>   * more nor chips.  This current list focusses on newer chips, which
>   * have been converging on command sets which including JEDEC ID.
> @@ -2715,6 +2904,9 @@ static const struct flash_info spi_nor_ids[] = {
>         { "s25fl064l",  INFO(0x016017,      0,  64 * 1024, 128, SECT_4K |
> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
>         { "s25fl128l",  INFO(0x016018,      0,  64 * 1024, 256, SECT_4K |
> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
>         { "s25fl256l",  INFO(0x016019,      0,  64 * 1024, 512, SECT_4K |
> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
> +       { "s28hs512t",  INFO(0x345b1a,      0, 256 * 1024, 256, SECT_4K |
> SPI_NOR_OCTAL_DTR_READ)
> +               .fixups = &s28hs512t_fixups,
> +       },
> 
>         /* SST -- large erase sizes are "overlays", "sectors" are 4K */
>         { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K |
> SST_WRITE) }, diff --git a/include/linux/mtd/spi-nor.h
> b/include/linux/mtd/spi-nor.h index c653f6713cfc..e765272fc0f4 100644
> --- a/include/linux/mtd/spi-nor.h
> +++ b/include/linux/mtd/spi-nor.h
> @@ -150,6 +150,20 @@
>  #define SR2_QUAD_EN_BIT1       BIT(1)
>  #define SR2_QUAD_EN_BIT7       BIT(7)
> 
> +/* For Cypress flash. */
> +#define SPINOR_OP_RD_ANY_REG                   0x65    /* Read any register
> */
> +#define SPINOR_OP_WR_ANY_REG                   0x71    /* Write any register
> */
> +#define SPINOR_REG_CYPRESS_CFR2V               0x00800003
> +#define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_8_20   0x8
> +#define SPINOR_REG_CYPRESS_CFR3N               0x00000004
> +#define SPINOR_REG_CYPRESS_CFR3V               0x00800004
> +#define SPINOR_REG_CYPRESS_CFR3V_PGSZ          BIT(4) /* Page size. */
> +#define SPINOR_REG_CYPRESS_CFR3N_UNISECT       BIT(3) /* Uniform
> sector mode */
> +#define SPINOR_REG_CYPRESS_CFR4V               0x00800005
> +#define SPINOR_REG_CYPRESS_CFR5V               0x00800006
> +#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN    0x3
> +#define SPINOR_OP_CYPRESS_RD_FAST              0xee
> +
>  /* Supported SPI protocols */
>  #define SNOR_PROTO_INST_MASK   GENMASK(23, 16)
>  #define SNOR_PROTO_INST_SHIFT  16
> --
> 2.25.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, back to index

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
2020-02-11 13:33 ` [PATCH 1/9] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
2020-02-11 13:33 ` [PATCH 2/9] spi: spi-mem: allow specifying a command's extension Pratyush Yadav
2020-02-11 13:33 ` [PATCH 3/9] spi: cadence-quadspi: Add support for octal DTR flashes Pratyush Yadav
2020-02-11 13:33 ` [PATCH 4/9] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
2020-02-11 13:33 ` [PATCH 5/9] mtd: spi-nor: get command opcode extension type from BFPT Pratyush Yadav
2020-02-11 13:33 ` [PATCH 6/9] mtd: spi-nor: parse xSPI Profile 1.0 table Pratyush Yadav
2020-02-11 13:33 ` [PATCH 7/9] mtd: spi-nor: use dummy cycle and address width info from SFDP Pratyush Yadav
2020-02-11 13:33 ` [PATCH 8/9] mtd: spi-nor: enable octal DTR mode when possible Pratyush Yadav
2020-02-11 13:33 ` [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash Pratyush Yadav
2020-02-13 10:36   ` [EXT] " Kuldeep Singh

Linux-mtd Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-mtd/0 linux-mtd/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-mtd linux-mtd/ https://lore.kernel.org/linux-mtd \
		linux-mtd@lists.infradead.org
	public-inbox-index linux-mtd

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-mtd


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git