linux-rtc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dan Murphy <dmurphy@ti.com>
To: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>,
	<mazziesaccount@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Bartosz Golaszewski <bgolaszewski@baylibre.com>,
	Jacek Anaszewski <jacek.anaszewski@gmail.com>,
	Pavel Machek <pavel@ucw.cz>,
	Alessandro Zummo <a.zummo@towertech.it>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-clk@vger.kernel.org>, <linux-gpio@vger.kernel.org>,
	<linux-leds@vger.kernel.org>, <linux-rtc@vger.kernel.org>
Subject: Re: [RFC PATCH 12/13] dt-bindings: mfd: Document ROHM BD71282 bindings
Date: Thu, 17 Oct 2019 09:18:15 -0500	[thread overview]
Message-ID: <1d2bc596-0329-d090-2e8d-037c8cad0585@ti.com> (raw)
In-Reply-To: <05841ff33ea166bc6934456a492adc3c67a90670.1571302099.git.matti.vaittinen@fi.rohmeurope.com>

Matt

On 10/17/19 4:55 AM, Matti Vaittinen wrote:
> ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
> a real-time clock (RTC), 3 GPO/regulator control pins, HALL input pin
> and a 32.768 kHz clock gate.
>
> Document the dt bindings drivers are using.

This should be patch 1 of X


> Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
> ---
>   .../bindings/mfd/rohm,bd71828-pmic.txt        | 180 ++++++++++++++++++
>   1 file changed, 180 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
> new file mode 100644
> index 000000000000..125efa9f3de0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
> @@ -0,0 +1,180 @@
> +* ROHM BD71828 Power Management Integrated Circuit bindings
> +
> +BD71828GW is a single-chip power management IC for battery-powered portable
> +devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA single-cell
> +linear charger. Also included is a Coulomb counter, a real-time clock (RTC),
> +and a 32.768 kHz clock gate.
> +
> +Required properties:
> + - compatible			: Should be "rohm,bd71828".
> + - reg				: I2C slave address.
> + - interrupt-parent		: Phandle to the parent interrupt controller.
> + - interrupts			: The interrupt line the device is connected to.
> + - clocks			: The parent clock connected to PMIC.
> + - #clock-cells			: Should be 0.
> + - regulators			: List of child nodes that specify the
> +				  regulators. Please see
> +				  ../regulator/rohm,bd71828-regulator.txt
> + - gpio-controller		: To indicate BD71828 acts as a GPIO controller.
> + - #gpio-cells			: Should be 2. The first cell is the pin number
> +				  and the second cell is used to specify flags.
> +				  See ../gpio/gpio.txt for more information.
> +
> +The BD71828 RUN state is divided into 4 configurable run-levels named RUN0,
> +RUN1, RUN2 and RUN3. Bucks 1, 2, 6 and 7 can be either controlled individually
> +via I2C, or some/all of them can be bound to run-levels and controlled as a
> +group. If bucks are controlled individually these run-levels are ignored. See
> +../regulator/rohm,bd71828-regulator.txt for how to define regulator voltages
> +for run-levels. Run-levels can be changed by I2C or GPIO depending on PMIC's OTP
> +configuration.
> +
> +Optional properties:
> +- clock-output-names		: Should contain name for output clock.
> +- rohm,dvs-vsel-gpios		: GPIOs used to control PMIC run-levels. Should
> +				  describe two GPIOs. (See run-level control in
> +				  data-sheet). If this property is omitted but
> +				  some bucks are marked to be controlled by
> +				  run-levels - then OTP option allowing
> +				  run-level control via I2C is assumed.
> +- gpio-reserved-ranges		: Usage of GPIO pins can be changed via OTP.
> +				  This property can be used to mark the pins
> +				  which should not be configured for GPIO.
> +				  Please see the ../gpio/gpio.txt for more
> +				  information.
> +
> +Example:
> +
> +        /* external oscillator node */
> +        osc: oscillator {
> +                compatible = "fixed-clock";
> +                #clock-cells = <1>;
> +                clock-frequency  = <32768>;
> +                clock-output-names = "osc";
> +        };
> +
> +	pmic: pmic@4b {
> +		compatible = "rohm,bd71828";
> +		reg = <0x4b>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <29 GPIO_ACTIVE_LOW>;
> +		clocks = <&osc 0>;
> +		#clock-cells = <0>;
> +		clock-output-names = "bd71828-32k-out";
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		ngpios = <4>;
> +		gpio-reserved-ranges = <0 1 2 1>;
> +		gpio-line-names = "EPDEN";
> +		rohm,dvs-vsel-gpios = <&gpio1 12 0>,
> +				      <&gpio1 13 0>;
> +		regulators {
> +			buck1: BUCK1 {
> +				regulator-name = "buck1";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <2000000>;
> +				regulator-ramp-delay = <2500>;
> +				rohm,dvs-runlvl-ctrl;
> +				rohm,dvs-runlevel0-voltage = <500000>;
> +				rohm,dvs-runlevel1-voltage = <506250>;
> +				rohm,dvs-runlevel2-voltage = <512500>;
> +				rohm,dvs-runlevel3-voltage = <518750>;
> +				regulator-boot-on;
> +			};
> +			buck2: BUCK2 {
> +				regulator-name = "buck2";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <2000000>;
> +				regulator-ramp-delay = <2500>;
> +				rohm,dvs-runlvl-ctrl;
> +				rohm,dvs-runlevel0-voltage = <500000>;
> +				rohm,dvs-runlevel1-voltage = <506250>;
> +				rohm,dvs-runlevel2-voltage = <512500>;
> +				rohm,dvs-runlevel3-voltage = <518750>;
> +				regulator-boot-on;
> +			};
> +			buck3: BUCK3 {
> +				regulator-name = "buck3";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <2000000>;
> +				regulator-boot-on;
> +			};
> +			buck4: BUCK4 {
> +				regulator-name = "buck4";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +			};
> +			buck5: BUCK5 {
> +				regulator-name = "buck5";
> +				regulator-min-microvolt = <2500000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +			buck6: BUCK6 {
> +				regulator-name = "buck6";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <2000000>;
> +				regulator-ramp-delay = <2500>;
> +				rohm,dvs-runlvl-ctrl;
> +				rohm,dvs-runlevel0-voltage = <500000>;
> +				rohm,dvs-runlevel1-voltage = <506250>;
> +				rohm,dvs-runlevel2-voltage = <512500>;
> +				rohm,dvs-runlevel3-voltage = <518750>;
> +				regulator-boot-on;
> +			};
> +			buck7: BUCK7 {
> +				regulator-name = "buck7";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <2000000>;
> +				regulator-ramp-delay = <2500>;
> +				rohm,dvs-runlvl-ctrl;
> +				rohm,dvs-runlevel0-voltage = <500000>;
> +				rohm,dvs-runlevel1-voltage = <506250>;
> +				rohm,dvs-runlevel2-voltage = <512500>;
> +				rohm,dvs-runlevel3-voltage = <518750>;
> +				regulator-boot-on;
> +			};
> +			ldo1: LDO1 {
> +				regulator-name = "ldo1";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +			ldo2: LDO2 {
> +				regulator-name = "ldo2";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +			ldo3: LDO3 {
> +				regulator-name = "ldo3";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +			ldo4: LDO4 {
> +				regulator-name = "ldo4";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +			ldo5: LDO5 {
> +				regulator-name = "ldo5";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +			ldo6: LDO6 {
> +				regulator-name = "ldo6";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +			};
> +			ldo7_reg: LDO7 {
> +				regulator-name = "ldo7";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +			};
> +		};
> +	};

  reply	other threads:[~2019-10-17 14:19 UTC|newest]

Thread overview: 43+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-17  9:40 [RFC PATCH 00/13] Support ROHM BD71828 PMIC Matti Vaittinen
2019-10-17  9:41 ` [RFC PATCH 01/13] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-10-17  9:42 ` [RFC PATCH 02/13] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-10-17  9:43 ` [RFC PATCH 03/13] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-10-17  9:44 ` [RFC PATCH 04/13] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2019-10-17  9:44 ` [RFC PATCH 05/13] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-10-17  9:48 ` [RFC PATCH 06/13] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-10-17  9:50 ` [RFC PATCH 07/13] regulator: bd71828: enhanced run-level support Matti Vaittinen
2019-10-17  9:51 ` [RFC PATCH 08/13] regulator: bd71828: Support in-kernel APIs to change run-level Matti Vaittinen
2019-10-17  9:52 ` [RFC PATCH 09/13] mfd: rtc: support RTC on ROHM BD71828 with BD70528 driver Matti Vaittinen
2019-10-17 10:12   ` Alexandre Belloni
2019-10-17 10:36     ` Vaittinen, Matti
2019-10-17 10:48       ` Alexandre Belloni
2019-10-21  5:29         ` Vaittinen, Matti
2019-10-23 10:27         ` Vaittinen, Matti
2019-10-29 13:50           ` Alexandre Belloni
2019-10-29 14:08             ` Vaittinen, Matti
2019-10-17  9:53 ` [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-10-17 12:45   ` Bartosz Golaszewski
2019-10-21  7:00     ` Vaittinen, Matti
2019-10-21 14:36       ` Bartosz Golaszewski
2019-10-21 14:56         ` Vaittinen, Matti
2019-10-22 13:19         ` Vaittinen, Matti
2019-10-17  9:53 ` [RFC PATCH 11/13] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen
2019-10-17 14:04   ` Dan Murphy
2019-10-17 14:28     ` Alexandre Belloni
2019-10-21  8:00     ` Vaittinen, Matti
2019-10-21 19:09       ` Jacek Anaszewski
2019-10-22 12:40         ` Vaittinen, Matti
2019-10-22 17:40           ` Jacek Anaszewski
2019-10-23  8:37             ` Vaittinen, Matti
2019-10-23 21:59               ` Jacek Anaszewski
2019-10-24  8:15                 ` Vaittinen, Matti
2019-10-24 22:04                   ` Jacek Anaszewski
2019-10-25  7:07                     ` Vaittinen, Matti
2019-10-25 13:24                       ` Rob Herring
2019-10-25 14:37                         ` Vaittinen, Matti
2019-10-25 15:47                           ` Rob Herring
2019-10-29 13:29                             ` Vaittinen, Matti
2019-10-17  9:55 ` [RFC PATCH 12/13] dt-bindings: mfd: Document ROHM BD71282 bindings Matti Vaittinen
2019-10-17 14:18   ` Dan Murphy [this message]
2019-10-21  8:03     ` Vaittinen, Matti
2019-10-17  9:57 ` [RFC PATCH 13/13] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1d2bc596-0329-d090-2e8d-037c8cad0585@ti.com \
    --to=dmurphy@ti.com \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=matti.vaittinen@fi.rohmeurope.com \
    --cc=mazziesaccount@gmail.com \
    --cc=mturquette@baylibre.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).