Re: [PATCH 08/15] ARM/arm64: sunxi: Move H3/H5 syscon label over to soc-specific nodes

[Paul Kocialkowski <paul.kocialkowski@bootlin.com>]

Hi,

Le vendredi 16 novembre 2018 à 17:47 +0800, Chen-Yu Tsai a écrit :
> On Fri, Nov 16, 2018 at 5:39 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
> > On Thu, Nov 15, 2018 at 03:50:06PM +0100, Paul Kocialkowski wrote:
> > > Now that we have specific nodes for the H3 and H5 system-controller
> > > that allow proper access to the EMAC clock configuration register,
> > > we no longer need a common dummy syscon node.
> > > 
> > > Switch the syscon label over to each platform's dtsi file.
> > > 
> > > Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
> > > ---
> > >  arch/arm/boot/dts/sun8i-h3.dtsi              | 2 +-
> > >  arch/arm/boot/dts/sunxi-h3-h5.dtsi           | 6 ------
> > >  arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 2 +-
> > >  3 files changed, 2 insertions(+), 8 deletions(-)
> > > 
> > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> > > index 7157d954fb8c..b337a9282783 100644
> > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> > > @@ -134,7 +134,7 @@
> > >       };
> > > 
> > >       soc {
> > > -             system-control@1c00000 {
> > > +             syscon: system-control@1c00000 {
> > >                       compatible = "allwinner,sun8i-h3-system-control";
> > >                       reg = <0x01c00000 0x1000>;
> > >                       #address-cells = <1>;
> > > diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> > > index 4b1530ebe427..9175ff0fb59a 100644
> > > --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> > > +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> > > @@ -152,12 +152,6 @@
> > >                       };
> > >               };
> > > 
> > > -             syscon: syscon@1c00000 {
> > > -                     compatible = "allwinner,sun8i-h3-system-controller",
> > > -                             "syscon";
> > > -                     reg = <0x01c00000 0x1000>;
> > > -             };
> > > -
> > 
> > You're also dropping the syscon compatible there. But I'm not sure how
> > it could work with the H3 EMAC driver that would overwrite the
> > compatible already.
> 
> I assume you are referring to the previous patch? The node names are not
> the same, hence the previous patch is adding another node for the system
> controller, and this patch removes the old one with the "syscon" compatible.
> 
> We already patched the EMAC driver to support the new SRAM controller based
> regmap, so other than making people unhappy about having to update their
> DT, I don't think there would be any problems. This also means H3 in -next
> currently has _two_ syscon nodes.

Yes, the point is indeed to only have a single node per platform (in
the platform dtsi) instead of two (one in the common h3-h5 dtsi and one
in the platform dtsi).

I guess updating the dt is not even a hard requirement after this
series: things will keep working with the dummy syscon node for giving
the EMAC driver access to the syscon registers.

Cheers,

Paul