From: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
To: lee.jones@linaro.org, broonie@kernel.org,
linus.walleij@linaro.org, gnurou@gmail.com,
cw00.choi@samsung.com
Cc: myungjoo.ham@samsung.com, devicetree@vger.kernel.org,
alsa-devel@alsa-project.org, patches@opensource.wolfsonmicro.com,
linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
ckeepax@opensource.wolfsonmicro.com
Subject: [PATCH v3 8/8] Documentation: Add WM8998/WM1814 device tree bindings
Date: Fri, 1 May 2015 16:15:19 +0100 [thread overview]
Message-ID: <1430493319-23808-9-git-send-email-rf@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1430493319-23808-1-git-send-email-rf@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
---
Documentation/devicetree/bindings/mfd/arizona.txt | 13 +++++++++----
1 files changed, 9 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
index 7665aa9..64fa3b2 100644
--- a/Documentation/devicetree/bindings/mfd/arizona.txt
+++ b/Documentation/devicetree/bindings/mfd/arizona.txt
@@ -10,6 +10,9 @@ Required properties:
"wlf,wm5110"
"wlf,wm8280"
"wlf,wm8997"
+ "wlf,wm8998"
+ "wlf,wm1814"
+
- reg : I2C slave address when connected using I2C, chip select number when
using SPI.
@@ -31,10 +34,10 @@ Required properties:
as covered in Documentation/devicetree/bindings/regulator/regulator.txt
- DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102,
- wm5110, wm8280)
+ wm5110, wm8280, wm8998, wm1814)
- SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102,
- wm5110, wm8280)
+ wm5110, wm8280, wm8998, wm1814)
- SPKVDD-supply : Speaker driver power supply (wm8997)
@@ -53,8 +56,10 @@ Optional properties:
of input signals. Valid values are 0 (Differential), 1 (Single-ended) and
2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default.
If present, values must be specified less than or equal to the number of
- input singals. If values less than the number of input signals, elements
- that has not been specifed are set to 0 by default.
+ input signals. If values less than the number of input signals, elements
+ that have not been specified are set to 0 by default. Entries are:
+ <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997)
+ <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814)
- wlf,dmic-ref : DMIC reference voltage source for each input, can be
selected from either MICVDD or one of the MICBIAS's, defines
--
1.7.2.5
next prev parent reply other threads:[~2015-05-01 15:16 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-01 15:15 [PATCH v3 0/8] Add support for Wolfson WM8998 and WM1814 codecs Richard Fitzgerald
2015-05-01 15:15 ` [PATCH v3 1/8] mfd: arizona: Split INx_MODE into two fields Richard Fitzgerald
2015-05-13 12:28 ` Lee Jones
2015-05-01 15:15 ` [PATCH v3 2/8] ASoC: arizona: add defines for single-input gain control Richard Fitzgerald
2015-05-01 15:15 ` [PATCH v3 3/8] mfd: arizona: Add support for WM8998 and WM1814 Richard Fitzgerald
2015-05-02 9:58 ` Paul Bolle
2015-05-04 9:11 ` Richard Fitzgerald
2015-05-04 10:44 ` Paul Bolle
2015-05-07 8:52 ` Lee Jones
2015-05-08 9:11 ` Richard Fitzgerald
2015-05-01 15:15 ` [PATCH v3 4/8] gpio: arizona: add " Richard Fitzgerald
2015-05-01 15:15 ` [PATCH v3 5/8] regulator: " Richard Fitzgerald
2015-05-01 15:15 ` [PATCH v3 6/8] extcon: arizona: Add " Richard Fitzgerald
2015-05-01 15:15 ` [PATCH v3 7/8] ASoC: wm8998: Initial WM8998 codec driver Richard Fitzgerald
2015-05-04 11:39 ` Mark Brown
2015-05-05 9:24 ` Richard Fitzgerald
2015-05-05 10:53 ` Mark Brown
2015-05-05 13:31 ` Richard Fitzgerald
2015-05-05 21:59 ` Mark Brown
2015-05-06 9:24 ` Richard Fitzgerald
2015-05-06 11:48 ` Mark Brown
2015-05-06 12:21 ` Richard Fitzgerald
2015-05-06 12:34 ` Mark Brown
2015-05-01 15:15 ` Richard Fitzgerald [this message]
2015-05-13 12:29 ` [PATCH v3 8/8] Documentation: Add WM8998/WM1814 device tree bindings Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1430493319-23808-9-git-send-email-rf@opensource.wolfsonmicro.com \
--to=rf@opensource.wolfsonmicro.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=ckeepax@opensource.wolfsonmicro.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=gnurou@gmail.com \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
--cc=patches@opensource.wolfsonmicro.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).