[PATCH 1/3] devicetree: mfd: Add binding for the TI LM3533

[PATCH 1/3] devicetree: mfd: Add binding for the TI LM3533

[Bjorn Andersson]

Add the binding for the Texas Instruments LM3533 lighting power
solution.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
 Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
 1 file changed, 183 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt

diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
new file mode 100644
index 000000000000..3cc41695a544
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
@@ -0,0 +1,183 @@
+Texas Instruments LM3533 binding
+
+This binding describes the Texas Instruments LM3533, a lighting power solution
+for smartphone handsets. The common properties are described directly in the
+node, while each individual component are described in an optional subnode.
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be:
+		    "ti,lm3533"
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: i2c address of the LM3533 chip
+
+- ti,hwen-gpios:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: reference to gpio pin connected to the HWEN input; as
+		    specified in "gpio/gpio.txt"
+
+- ti,als-supply:
+	Usage: optional
+	Value type: <prop-encoded-array>
+	Definition: reference to regulator powering the V_als input; as
+		    specified in "regulator/regulator.txt"
+
+- ti,boost-freq:
+	Usage: required
+	Value type: <u32>
+	Definition: switch-frequency of the boost converter, must be either:
+		    500000 or 1000000
+
+- ti,boost-ovp:
+	Usage: required
+	Value type: <u32>
+	Definition: over voltage protection limit, must be one of: 16, 24, 32
+		    or 40
+
+- #address-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 1
+
+- #size-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 0
+
+= ALS SUBNODE
+The als subnode must be named "als", it carries the als related properties.
+
+- ti,als-resistance:
+	Usage: required (unless ti,pwm-mode is specified)
+	Value type: <u32>
+	Definition: specifies the resistor value (R_als), in Ohm. Valid values
+		    ranges from 200kOhm to 1574Ohm.
+
+- ti,pwm-mode:
+	Usage: optional
+	Value type: <empty>
+	Definition: specifies, if present, that the als should operate in pwm
+		    mode - rather than analog mode
+
+= BACKLIGHT NODES
+Backlight subnodes must be named "backlight", they carry the backlight related
+properties.
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies which of the two backlights this node corresponds
+		    to
+
+- default-brightness:
+	Usage: optional
+	Value type: <32>
+	Definition: specifies the default brightness for the backlight, in
+		    units of brightness [0-255]
+
+- label:
+	Usage: required
+	Value type: <string>
+	Definition: specifies a name of this backlight
+
+- led-max-microamp:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies the max current for this backlight, in uA, as
+		    described in "leds/common.txt"
+
+- ti,pwm-zones:
+	Usage: optional
+	Value type: <u32 list>
+	Definition: lists the ALS zones to be PWM controlled for this backlight,
+		    the values in the list are in the range [0 - 4]
+
+= LED NODES
+LED subnodes must be named "led", they carry the LED related properties.
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies which of the four LEDs this node corresponds to
+
+- linux,default-trigger:
+	Usage: optional
+	Value type: <string>
+	Definition: specifies the default trigger for the LED, as described in
+		    "leds/common.txt"
+
+- label:
+	Usage: required
+	Value type: <string>
+	Definition: specifies a name of this LED, as described in
+		    "leds/common.txt"
+
+- led-max-microamp:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies the max current for this LED, in uA, as described
+		    in "leds/common.txt"
+
+- ti,pwm-zones:
+	Usage: optional
+	Value type: <u32 list>
+	Definition: lists the ALS zones to be PWM controlled for this LED, the
+		    values in the list are in the range [0 - 4]
+
+= EXAMPLE
+
+i2c@12460000 {
+	compatible = "qcom,i2c-qup-v1.1.1";
+	...
+
+	lm3533@36 {
+		compatible = "ti,lm3533";
+		reg = <0x36>;
+
+		ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
+		ti,als-supply = <&pm8921_l11>;
+
+		ti,boost-freq = <500000>;
+		ti,boost-ovp = <24>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		als {
+			ti,als-resistance = <200000>;
+		};
+
+		backlight@0 {
+			reg = <0>;
+			label = "backlight";
+
+			led-max-microamp = <20200>;
+		};
+
+		led@0 {
+			reg = <0>;
+			label = "red";
+
+			led-max-microamp = <5000>;
+		};
+
+		led@1 {
+			reg = <1>;
+			label = "green";
+
+			led-max-microamp = <5000>;
+		};
+
+		led@2 {
+			reg = <2>;
+			label = "blue";
+
+			led-max-microamp = <5000>;
+		};
+	};
+
-- 
2.4.2

[PATCH 2/3] iio: light: lm3533-als: Print error message on invalid resistance

[Bjorn Andersson]

Print an error message to indicate that invalid configuration data was
provided in the platform_data, rather than just aborting initialization.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---

This patch can be picked independently of the other 2, but included in the
series for "completeness".

 drivers/iio/light/lm3533-als.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c
index 076bc46fad03..e56937c40a18 100644
--- a/drivers/iio/light/lm3533-als.c
+++ b/drivers/iio/light/lm3533-als.c
@@ -743,8 +743,10 @@ static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val)
 {
 	int ret;
 
-	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX)
+	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) {
+		dev_err(&als->pdev->dev, "invalid resistor value\n");
 		return -EINVAL;
+	};
 
 	ret = lm3533_write(als->lm3533, LM3533_REG_ALS_RESISTOR_SELECT, val);
 	if (ret) {
-- 
2.4.2

Re: [PATCH 2/3] iio: light: lm3533-als: Print error message on invalid resistance

[Joe Perches]

On Sun, 2015-10-25 at 11:09 -0700, Bjorn Andersson wrote:
> Print an error message to indicate that invalid configuration data was
> provided in the platform_data, rather than just aborting initialization.

Perhaps it'd be nicer to show the 3 values.

> diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c
[]
> @@ -743,8 +743,10 @@ static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val)
>  {
>  	int ret;
>  
> -	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX)
> +	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) {
> +		dev_err(&als->pdev->dev, "invalid resistor value\n");
>  		return -EINVAL;
> +	};
>  
>  	ret = lm3533_write(als->lm3533, LM3533_REG_ALS_RESISTOR_SELECT, val);
>  	if (ret) {

Re: [PATCH 2/3] iio: light: lm3533-als: Print error message on invalid resistance

[Bjorn Andersson]

On Tue 27 Oct 12:18 PDT 2015, Joe Perches wrote:

> On Sun, 2015-10-25 at 11:09 -0700, Bjorn Andersson wrote:
> > Print an error message to indicate that invalid configuration data was
> > provided in the platform_data, rather than just aborting initialization.
> 
> Perhaps it'd be nicer to show the 3 values.
> 

I do agree that it would be helpful to hint the developer about the
expected range. The problem I see here though is that, in the case of
devicetree we've now moved from resistance to a register value.

E.g. specifying 500kOhm in dt would make this piece complain about a
resistance of 0 being invalid and I would have to read the code and/or
datasheet anyways to find the valid range.


The reason I did not put this error print in the dt parser was that I
did not want to replicate the resistor limits and I figured it would be
useful for platform_data users as well. But if this is going to be
informative I think I need to move it.

So would you be okay with not improving the message? Or would you like
me to just move it into the code in patch 1 - and leave the
platform_data case as it was (with a silent failure)?

> > diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c
> []
> > @@ -743,8 +743,10 @@ static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val)
> >  {
> >  	int ret;
> >  
> > -	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX)
> > +	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) {
> > +		dev_err(&als->pdev->dev, "invalid resistor value\n");
> >  		return -EINVAL;
> > +	};
> >  

Regards,
Bjorn

Re: [PATCH 2/3] iio: light: lm3533-als: Print error message on invalid resistance

[Joe Perches]

On Wed, 2015-10-28 at 11:37 -0700, Bjorn Andersson wrote:
> On Tue 27 Oct 12:18 PDT 2015, Joe Perches wrote:
> > On Sun, 2015-10-25 at 11:09 -0700, Bjorn Andersson wrote:
> > > Print an error message to indicate that invalid configuration data was
> > > provided in the platform_data, rather than just aborting initialization.
> > Perhaps it'd be nicer to show the 3 values.
> I do agree that it would be helpful to hint the developer about the
> expected range. The problem I see here though is that, in the case of
> devicetree we've now moved from resistance to a register value.
[]
> So would you be okay with not improving the message? Or would you like
> me to just move it into the code in patch 1 - and leave the
> platform_data case as it was (with a silent failure)?
[]
> > > diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c
> > []
> > > @@ -743,8 +743,10 @@ static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val)
> > >  {
> > >  	int ret;
> > >  
> > > -	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX)
> > > +	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) {
> > > +		dev_err(&als->pdev->dev, "invalid resistor value\n");
> > >  		return -EINVAL;
> > > +	};
> > >  

What I suggested was just a trivial proposal.
Whatever you do is fine with me.

[PATCH 3/3] mfd: lm3533: Support initialization from Device Tree

[Bjorn Andersson]

Implement Device Tree parsing functions to support initialization of the
lm3533 drivers.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
 drivers/mfd/lm3533-core.c | 265 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 265 insertions(+)

diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c
index 5abcbb2e8849..acdb3d580277 100644
--- a/drivers/mfd/lm3533-core.c
+++ b/drivers/mfd/lm3533-core.c
@@ -18,6 +18,7 @@
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/mfd/core.h>
+#include <linux/of_gpio.h>
 #include <linux/regmap.h>
 #include <linux/seq_file.h>
 #include <linux/slab.h>
@@ -25,6 +26,8 @@
 
 #include <linux/mfd/lm3533.h>
 
+#define LM3533_DEFAULT_BRIGHTNESS	200
 
 #define LM3533_BOOST_OVP_MASK		0x06
 #define LM3533_BOOST_OVP_SHIFT		1
@@ -588,10 +591,266 @@ static const struct regmap_config regmap_config = {
 	.precious_reg	= lm3533_precious_register,
 };
 
+static int lm3533_of_parse_enum(struct device_node *node,
+				const char *propname,
+				const unsigned *match, size_t num_matches)
+{
+	size_t i;
+	int ret;
+	u32 val;
+
+	ret = of_property_read_u32(node, propname, &val);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < num_matches; i++) {
+		if (val == match[i])
+			return i;
+	}
+
+	return -EINVAL;
+}
+
+static int lm3533_of_parse_pwm_zones(struct device_node *node)
+{
+	const char *propname = "ti,pwm-zones";
+	u32 zones[5];
+	int count;
+	int ret;
+	int i;
+
+	count = of_property_count_u32_elems(node, propname);
+	if (count == -EINVAL)
+		return 0;
+	if (count <= 0)
+		return count;
+	if (count >= ARRAY_SIZE(zones))
+		return -EINVAL;
+
+	ret = of_property_read_u32_array(node, propname, zones, count);
+	if (ret < 0)
+		return ret;
+
+	/* Enable pwm input, and enable the selected zones */
+	ret = BIT(0);
+	for (i = 0; i < count; i++)
+		ret |= BIT(zones[i] + 1);
+
+	return ret;
+}
+
+static int lm3533_of_parse_als_node(struct device *dev,
+				    struct device_node *node,
+				    struct lm3533_platform_data *pdata)
+{
+	struct lm3533_als_platform_data *als_pdata;
+	int ret;
+	u32 val;
+
+	als_pdata = devm_kzalloc(dev,
+				 sizeof(struct lm3533_als_platform_data),
+				 GFP_KERNEL);
+	if (!als_pdata)
+		return -ENOMEM;
+
+	als_pdata->pwm_mode = of_property_read_bool(node, "ti,pwm-mode");
+
+	ret = of_property_read_u32(node, "ti,als-resistance", &val);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "unable to read ti,als-resistance");
+		return ret;
+	}
+
+	/* Leave at high-Z, if the property was omitted or specified as 0 */
+	if (!ret && val != 0)
+		als_pdata->r_select = 200000 / val;
+
+	pdata->als = als_pdata;
+
+	return 0;
+}
+
+static int lm3533_of_parse_bl_node(struct device *dev,
+				   struct device_node *node,
+				   struct lm3533_platform_data *pdata)
+{
+	struct lm3533_bl_platform_data *bl_pdata;
+	int ret;
+	u32 reg;
+	u32 val;
+
+	ret = of_property_read_u32(node, "reg", &reg);
+	if (ret < 0 || reg >= ARRAY_SIZE(lm3533_bl_devs)) {
+		dev_err(dev, "invalid reg property\n");
+		return ret;
+	}
+
+	bl_pdata = &pdata->backlights[reg];
+
+	/* Increment num_backlights if we're filling a new space */
+	if (reg + 1 > pdata->num_backlights)
+		pdata->num_backlights = reg + 1;
+
+	ret = of_property_read_string(node, "label",
+				      (const char **)&bl_pdata->name);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse label\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "led-max-microamp", &val);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse led-max-microamp\n");
+		return ret;
+	}
+	bl_pdata->max_current = val;
+
+	val = LM3533_DEFAULT_BRIGHTNESS;
+	ret = of_property_read_u32(node, "default-brightness", &val);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "unable to parse default-brightness\n");
+		return ret;
+	}
+	bl_pdata->default_brightness = val;
+
+	ret = lm3533_of_parse_pwm_zones(node);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,pwm-zones\n");
+		return ret;
+	}
+	bl_pdata->pwm = ret;
+
+	return 0;
+}
+
+static int lm3533_of_parse_led_node(struct device *dev,
+				    struct device_node *node,
+				    struct lm3533_platform_data *pdata)
+{
+	struct lm3533_led_platform_data *led_pdata;
+	int ret;
+	u32 reg;
+	u32 val;
+
+	ret = of_property_read_u32(node, "reg", &reg);
+	if (ret < 0 || reg >= ARRAY_SIZE(lm3533_led_devs)) {
+		dev_err(dev, "invalid reg property\n");
+		return ret;
+	}
+
+	led_pdata = &pdata->leds[reg];
+
+	/* Increment num_leds if we're filling a new space */
+	if (reg + 1 > pdata->num_leds)
+		pdata->num_leds = reg + 1;
+
+	ret = of_property_read_string(node, "label",
+				      (const char **)&led_pdata->name);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse label\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "led-max-microamp", &val);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse led-max-microamp\n");
+		return ret;
+	}
+	led_pdata->max_current = val;
+
+	ret = of_property_read_string(node, "linux,default-trigger",
+				      &led_pdata->default_trigger);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "unable to parse default-trigger\n");
+		return ret;
+	}
+
+	ret = lm3533_of_parse_pwm_zones(node);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,pwm-zones\n");
+		return ret;
+	}
+	led_pdata->pwm = ret;
+
+	return 0;
+}
+
+static int lm3533_pdata_from_of_node(struct device *dev)
+{
+	struct lm3533_platform_data *pdata;
+	struct device_node *node;
+	int ret;
+	const unsigned freqs[] = {
+		[LM3533_BOOST_FREQ_500KHZ] = 500000,
+		[LM3533_BOOST_FREQ_1000KHZ] = 1000000,
+	};
+	const unsigned ovps[] = {
+		[LM3533_BOOST_OVP_16V] = 16,
+		[LM3533_BOOST_OVP_24V] = 24,
+		[LM3533_BOOST_OVP_32V] = 32,
+		[LM3533_BOOST_OVP_40V] = 40,
+	};
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->backlights = devm_kcalloc(dev,
+					 ARRAY_SIZE(lm3533_bl_devs),
+					 sizeof(struct lm3533_bl_platform_data),
+					 GFP_KERNEL);
+	if (!pdata->backlights)
+		return -ENOMEM;
+
+	pdata->leds = devm_kcalloc(dev,
+				   ARRAY_SIZE(lm3533_led_devs),
+				   sizeof(struct lm3533_led_platform_data),
+				   GFP_KERNEL);
+	if (!pdata->leds)
+		return -ENOMEM;
+
+	pdata->gpio_hwen = of_get_named_gpio(dev->of_node, "ti,hwen-gpios", 0);
+	if (pdata->gpio_hwen < 0)
+		return pdata->gpio_hwen;
+
+	ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-freq", freqs, 2);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,boost-freq\n");
+		return ret;
+	}
+	pdata->boost_freq = ret;
+
+	ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-ovp", ovps, 4);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,boost-ovp\n");
+		return ret;
+	}
+	pdata->boost_ovp = ret;
+
+	for_each_child_of_node(dev->of_node, node) {
+		if (!of_node_cmp(node->name, "als"))
+			ret = lm3533_of_parse_als_node(dev, node, pdata);
+		else if (!of_node_cmp(node->name, "backlight"))
+			ret = lm3533_of_parse_bl_node(dev, node, pdata);
+		else if (!of_node_cmp(node->name, "led"))
+			ret = lm3533_of_parse_led_node(dev, node, pdata);
+
+		if (ret < 0) {
+			of_node_put(node);
+			return ret;
+		}
+	}
+
+	dev->platform_data = pdata;
+
+	return 0;
+}
+
 static int lm3533_i2c_probe(struct i2c_client *i2c,
 					const struct i2c_device_id *id)
 {
 	struct lm3533 *lm3533;
+	int ret;
 
 	dev_dbg(&i2c->dev, "%s\n", __func__);
 
@@ -608,6 +867,12 @@ static int lm3533_i2c_probe(struct i2c_client *i2c,
 	lm3533->dev = &i2c->dev;
 	lm3533->irq = i2c->irq;
 
+	if (i2c->dev.of_node) {
+		ret = lm3533_pdata_from_of_node(lm3533->dev);
+		if (ret < 0)
+			return ret;
+	}
+
 	return lm3533_device_init(lm3533);
 }
 
-- 
2.4.2

Re: [PATCH 1/3] devicetree: mfd: Add binding for the TI LM3533

[Rob Herring]

On Sun, Oct 25, 2015 at 1:09 PM, Bjorn Andersson
<bjorn.andersson@sonymobile.com> wrote:
> Add the binding for the Texas Instruments LM3533 lighting power
> solution.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
>  Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
>  1 file changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
> new file mode 100644
> index 000000000000..3cc41695a544
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
> @@ -0,0 +1,183 @@
> +Texas Instruments LM3533 binding
> +
> +This binding describes the Texas Instruments LM3533, a lighting power solution
> +for smartphone handsets. The common properties are described directly in the
> +node, while each individual component are described in an optional subnode.
> +
> +- compatible:
> +       Usage: required
> +       Value type: <stringlist>
> +       Definition: must be:
> +                   "ti,lm3533"
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: i2c address of the LM3533 chip
> +
> +- ti,hwen-gpios:
> +       Usage: required
> +       Value type: <prop-encoded-array>
> +       Definition: reference to gpio pin connected to the HWEN input; as
> +                   specified in "gpio/gpio.txt"
> +
> +- ti,als-supply:
> +       Usage: optional
> +       Value type: <prop-encoded-array>
> +       Definition: reference to regulator powering the V_als input; as
> +                   specified in "regulator/regulator.txt"
> +
> +- ti,boost-freq:

Append "-hz".

> +       Usage: required
> +       Value type: <u32>
> +       Definition: switch-frequency of the boost converter, must be either:
> +                   500000 or 1000000
> +
> +- ti,boost-ovp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: over voltage protection limit, must be one of: 16, 24, 32
> +                   or 40
> +
> +- #address-cells:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: must be 1
> +
> +- #size-cells:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: must be 0
> +
> += ALS SUBNODE
> +The als subnode must be named "als", it carries the als related properties.
> +
> +- ti,als-resistance:
> +       Usage: required (unless ti,pwm-mode is specified)
> +       Value type: <u32>
> +       Definition: specifies the resistor value (R_als), in Ohm. Valid values
> +                   ranges from 200kOhm to 1574Ohm.

So append "-kohm"?

> +
> +- ti,pwm-mode:
> +       Usage: optional
> +       Value type: <empty>
> +       Definition: specifies, if present, that the als should operate in pwm
> +                   mode - rather than analog mode
> +
> += BACKLIGHT NODES
> +Backlight subnodes must be named "backlight", they carry the backlight related
> +properties.
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies which of the two backlights this node corresponds
> +                   to
> +
> +- default-brightness:
> +       Usage: optional
> +       Value type: <32>
> +       Definition: specifies the default brightness for the backlight, in
> +                   units of brightness [0-255]
> +
> +- label:
> +       Usage: required
> +       Value type: <string>
> +       Definition: specifies a name of this backlight
> +
> +- led-max-microamp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies the max current for this backlight, in uA, as
> +                   described in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +       Usage: optional
> +       Value type: <u32 list>
> +       Definition: lists the ALS zones to be PWM controlled for this backlight,
> +                   the values in the list are in the range [0 - 4]
> +
> += LED NODES
> +LED subnodes must be named "led", they carry the LED related properties.
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies which of the four LEDs this node corresponds to
> +
> +- linux,default-trigger:
> +       Usage: optional
> +       Value type: <string>
> +       Definition: specifies the default trigger for the LED, as described in
> +                   "leds/common.txt"
> +
> +- label:
> +       Usage: required
> +       Value type: <string>
> +       Definition: specifies a name of this LED, as described in
> +                   "leds/common.txt"
> +
> +- led-max-microamp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies the max current for this LED, in uA, as described
> +                   in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +       Usage: optional
> +       Value type: <u32 list>
> +       Definition: lists the ALS zones to be PWM controlled for this LED, the
> +                   values in the list are in the range [0 - 4]
> +
> += EXAMPLE
> +
> +i2c@12460000 {
> +       compatible = "qcom,i2c-qup-v1.1.1";
> +       ...
> +
> +       lm3533@36 {
> +               compatible = "ti,lm3533";
> +               reg = <0x36>;
> +
> +               ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
> +               ti,als-supply = <&pm8921_l11>;
> +
> +               ti,boost-freq = <500000>;
> +               ti,boost-ovp = <24>;
> +
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               als {
> +                       ti,als-resistance = <200000>;
> +               };
> +
> +               backlight@0 {
> +                       reg = <0>;
> +                       label = "backlight";
> +
> +                       led-max-microamp = <20200>;
> +               };
> +
> +               led@0 {
> +                       reg = <0>;
> +                       label = "red";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +
> +               led@1 {
> +                       reg = <1>;
> +                       label = "green";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +
> +               led@2 {
> +                       reg = <2>;
> +                       label = "blue";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +       };
> +
> --
> 2.4.2
>

[PATCH v2 1/3] devicetree: mfd: Add binding for the TI LM3533

[Bjorn Andersson]

Add the binding for the Texas Instruments LM3533 lighting power
solution.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---

Changes since v1:
- Added unit to boost-freq and als-resistance (as the frequency now comes with
  a unit specifier I changed it to be expressed in kHz)

 Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
 1 file changed, 183 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt

diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
new file mode 100644
index 000000000000..399df39ec7e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
@@ -0,0 +1,183 @@
+Texas Instruments LM3533 binding
+
+This binding describes the Texas Instruments LM3533, a lighting power solution
+for smartphone handsets. The common properties are described directly in the
+node, while each individual component are described in an optional subnode.
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be:
+		    "ti,lm3533"
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: i2c address of the LM3533 chip
+
+- ti,hwen-gpios:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: reference to gpio pin connected to the HWEN input; as
+		    specified in "gpio/gpio.txt"
+
+- ti,als-supply:
+	Usage: optional
+	Value type: <prop-encoded-array>
+	Definition: reference to regulator powering the V_als input; as
+		    specified in "regulator/regulator.txt"
+
+- ti,boost-freq-khz:
+	Usage: required
+	Value type: <u32>
+	Definition: switch-frequency of the boost converter, must be either:
+		    500 or 1000
+
+- ti,boost-ovp:
+	Usage: required
+	Value type: <u32>
+	Definition: over voltage protection limit, must be one of: 16, 24, 32
+		    or 40
+
+- #address-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 1
+
+- #size-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 0
+
+= ALS SUBNODE
+The als subnode must be named "als", it carries the als related properties.
+
+- ti,als-resistance-ohm:
+	Usage: required (unless ti,pwm-mode is specified)
+	Value type: <u32>
+	Definition: specifies the resistor value (R_als), in Ohm. Valid values
+		    ranges from 200kOhm to 1574Ohm.
+
+- ti,pwm-mode:
+	Usage: optional
+	Value type: <empty>
+	Definition: specifies, if present, that the als should operate in pwm
+		    mode - rather than analog mode
+
+= BACKLIGHT NODES
+Backlight subnodes must be named "backlight", they carry the backlight related
+properties.
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies which of the two backlights this node corresponds
+		    to
+
+- default-brightness:
+	Usage: optional
+	Value type: <32>
+	Definition: specifies the default brightness for the backlight, in
+		    units of brightness [0-255]
+
+- label:
+	Usage: required
+	Value type: <string>
+	Definition: specifies a name of this backlight
+
+- led-max-microamp:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies the max current for this backlight, in uA, as
+		    described in "leds/common.txt"
+
+- ti,pwm-zones:
+	Usage: optional
+	Value type: <u32 list>
+	Definition: lists the ALS zones to be PWM controlled for this backlight,
+		    the values in the list are in the range [0 - 4]
+
+= LED NODES
+LED subnodes must be named "led", they carry the LED related properties.
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies which of the four LEDs this node corresponds to
+
+- linux,default-trigger:
+	Usage: optional
+	Value type: <string>
+	Definition: specifies the default trigger for the LED, as described in
+		    "leds/common.txt"
+
+- label:
+	Usage: required
+	Value type: <string>
+	Definition: specifies a name of this LED, as described in
+		    "leds/common.txt"
+
+- led-max-microamp:
+	Usage: required
+	Value type: <u32>
+	Definition: specifies the max current for this LED, in uA, as described
+		    in "leds/common.txt"
+
+- ti,pwm-zones:
+	Usage: optional
+	Value type: <u32 list>
+	Definition: lists the ALS zones to be PWM controlled for this LED, the
+		    values in the list are in the range [0 - 4]
+
+= EXAMPLE
+
+i2c@12460000 {
+	compatible = "qcom,i2c-qup-v1.1.1";
+	...
+
+	lm3533@36 {
+		compatible = "ti,lm3533";
+		reg = <0x36>;
+
+		ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
+		ti,als-supply = <&pm8921_l11>;
+
+		ti,boost-freq = <500000>;
+		ti,boost-ovp = <24>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		als {
+			ti,als-resistance = <200000>;
+		};
+
+		backlight@0 {
+			reg = <0>;
+			label = "backlight";
+
+			led-max-microamp = <20200>;
+		};
+
+		led@0 {
+			reg = <0>;
+			label = "red";
+
+			led-max-microamp = <5000>;
+		};
+
+		led@1 {
+			reg = <1>;
+			label = "green";
+
+			led-max-microamp = <5000>;
+		};
+
+		led@2 {
+			reg = <2>;
+			label = "blue";
+
+			led-max-microamp = <5000>;
+		};
+	};
+
-- 
2.4.2

[PATCH v2 2/3] iio: light: lm3533-als: Print error message on invalid resistance

[Bjorn Andersson]

Print an error message to indicate that invalid configuration data was
provided in the platform_data, rather than just aborting initialization.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---

This patch can be picked independently of the other 2, but included in the
series for "completeness".

No changes since v1 in this patch.

 drivers/iio/light/lm3533-als.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c
index 076bc46fad03..e56937c40a18 100644
--- a/drivers/iio/light/lm3533-als.c
+++ b/drivers/iio/light/lm3533-als.c
@@ -743,8 +743,10 @@ static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val)
 {
 	int ret;
 
-	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX)
+	if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) {
+		dev_err(&als->pdev->dev, "invalid resistor value\n");
 		return -EINVAL;
+	};
 
 	ret = lm3533_write(als->lm3533, LM3533_REG_ALS_RESISTOR_SELECT, val);
 	if (ret) {
-- 
2.4.2

[PATCH v2 3/3] mfd: lm3533: Support initialization from Device Tree

[Bjorn Andersson]

Implement Device Tree parsing functions to support initialization of the
lm3533 drivers.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---

Changes since v1:
- Added units to bost-freq and als resistance

 drivers/mfd/lm3533-core.c | 264 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 264 insertions(+)

diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c
index 5abcbb2e8849..9f0fb362ee76 100644
--- a/drivers/mfd/lm3533-core.c
+++ b/drivers/mfd/lm3533-core.c
@@ -18,6 +18,7 @@
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/mfd/core.h>
+#include <linux/of_gpio.h>
 #include <linux/regmap.h>
 #include <linux/seq_file.h>
 #include <linux/slab.h>
@@ -25,6 +26,7 @@
 
 #include <linux/mfd/lm3533.h>
 
+#define LM3533_DEFAULT_BRIGHTNESS	200
 
 #define LM3533_BOOST_OVP_MASK		0x06
 #define LM3533_BOOST_OVP_SHIFT		1
@@ -588,10 +590,266 @@ static const struct regmap_config regmap_config = {
 	.precious_reg	= lm3533_precious_register,
 };
 
+static int lm3533_of_parse_enum(struct device_node *node,
+				const char *propname,
+				const unsigned *match, size_t num_matches)
+{
+	size_t i;
+	int ret;
+	u32 val;
+
+	ret = of_property_read_u32(node, propname, &val);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < num_matches; i++) {
+		if (val == match[i])
+			return i;
+	}
+
+	return -EINVAL;
+}
+
+static int lm3533_of_parse_pwm_zones(struct device_node *node)
+{
+	const char *propname = "ti,pwm-zones";
+	u32 zones[5];
+	int count;
+	int ret;
+	int i;
+
+	count = of_property_count_u32_elems(node, propname);
+	if (count == -EINVAL)
+		return 0;
+	if (count <= 0)
+		return count;
+	if (count >= ARRAY_SIZE(zones))
+		return -EINVAL;
+
+	ret = of_property_read_u32_array(node, propname, zones, count);
+	if (ret < 0)
+		return ret;
+
+	/* Enable pwm input, and enable the selected zones */
+	ret = BIT(0);
+	for (i = 0; i < count; i++)
+		ret |= BIT(zones[i] + 1);
+
+	return ret;
+}
+
+static int lm3533_of_parse_als_node(struct device *dev,
+				    struct device_node *node,
+				    struct lm3533_platform_data *pdata)
+{
+	struct lm3533_als_platform_data *als_pdata;
+	int ret;
+	u32 val;
+
+	als_pdata = devm_kzalloc(dev,
+				 sizeof(struct lm3533_als_platform_data),
+				 GFP_KERNEL);
+	if (!als_pdata)
+		return -ENOMEM;
+
+	als_pdata->pwm_mode = of_property_read_bool(node, "ti,pwm-mode");
+
+	ret = of_property_read_u32(node, "ti,als-resistance-ohm", &val);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "unable to read ti,als-resistance-ohm");
+		return ret;
+	}
+
+	/* Leave at high-Z, if the property was omitted or specified as 0 */
+	if (!ret && val != 0)
+		als_pdata->r_select = 200000 / val;
+
+	pdata->als = als_pdata;
+
+	return 0;
+}
+
+static int lm3533_of_parse_bl_node(struct device *dev,
+				   struct device_node *node,
+				   struct lm3533_platform_data *pdata)
+{
+	struct lm3533_bl_platform_data *bl_pdata;
+	int ret;
+	u32 reg;
+	u32 val;
+
+	ret = of_property_read_u32(node, "reg", &reg);
+	if (ret < 0 || reg >= ARRAY_SIZE(lm3533_bl_devs)) {
+		dev_err(dev, "invalid reg property\n");
+		return ret;
+	}
+
+	bl_pdata = &pdata->backlights[reg];
+
+	/* Increment num_backlights if we're filling a new space */
+	if (reg + 1 > pdata->num_backlights)
+		pdata->num_backlights = reg + 1;
+
+	ret = of_property_read_string(node, "label",
+				      (const char **)&bl_pdata->name);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse label\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "led-max-microamp", &val);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse led-max-microamp\n");
+		return ret;
+	}
+	bl_pdata->max_current = val;
+
+	val = LM3533_DEFAULT_BRIGHTNESS;
+	ret = of_property_read_u32(node, "default-brightness", &val);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "unable to parse default-brightness\n");
+		return ret;
+	}
+	bl_pdata->default_brightness = val;
+
+	ret = lm3533_of_parse_pwm_zones(node);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,pwm-zones\n");
+		return ret;
+	}
+	bl_pdata->pwm = ret;
+
+	return 0;
+}
+
+static int lm3533_of_parse_led_node(struct device *dev,
+				    struct device_node *node,
+				    struct lm3533_platform_data *pdata)
+{
+	struct lm3533_led_platform_data *led_pdata;
+	int ret;
+	u32 reg;
+	u32 val;
+
+	ret = of_property_read_u32(node, "reg", &reg);
+	if (ret < 0 || reg >= ARRAY_SIZE(lm3533_led_devs)) {
+		dev_err(dev, "invalid reg property\n");
+		return ret;
+	}
+
+	led_pdata = &pdata->leds[reg];
+
+	/* Increment num_leds if we're filling a new space */
+	if (reg + 1 > pdata->num_leds)
+		pdata->num_leds = reg + 1;
+
+	ret = of_property_read_string(node, "label",
+				      (const char **)&led_pdata->name);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse label\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "led-max-microamp", &val);
+	if (ret < 0) {
+		dev_err(dev, "unable to parse led-max-microamp\n");
+		return ret;
+	}
+	led_pdata->max_current = val;
+
+	ret = of_property_read_string(node, "linux,default-trigger",
+				      &led_pdata->default_trigger);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "unable to parse default-trigger\n");
+		return ret;
+	}
+
+	ret = lm3533_of_parse_pwm_zones(node);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,pwm-zones\n");
+		return ret;
+	}
+	led_pdata->pwm = ret;
+
+	return 0;
+}
+
+static int lm3533_pdata_from_of_node(struct device *dev)
+{
+	struct lm3533_platform_data *pdata;
+	struct device_node *node;
+	int ret;
+	const unsigned freqs[] = {
+		[LM3533_BOOST_FREQ_500KHZ] = 500,
+		[LM3533_BOOST_FREQ_1000KHZ] = 1000,
+	};
+	const unsigned ovps[] = {
+		[LM3533_BOOST_OVP_16V] = 16,
+		[LM3533_BOOST_OVP_24V] = 24,
+		[LM3533_BOOST_OVP_32V] = 32,
+		[LM3533_BOOST_OVP_40V] = 40,
+	};
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->backlights = devm_kcalloc(dev,
+					 ARRAY_SIZE(lm3533_bl_devs),
+					 sizeof(struct lm3533_bl_platform_data),
+					 GFP_KERNEL);
+	if (!pdata->backlights)
+		return -ENOMEM;
+
+	pdata->leds = devm_kcalloc(dev,
+				   ARRAY_SIZE(lm3533_led_devs),
+				   sizeof(struct lm3533_led_platform_data),
+				   GFP_KERNEL);
+	if (!pdata->leds)
+		return -ENOMEM;
+
+	pdata->gpio_hwen = of_get_named_gpio(dev->of_node, "ti,hwen-gpios", 0);
+	if (pdata->gpio_hwen < 0)
+		return pdata->gpio_hwen;
+
+	ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-freq-khz", freqs, 2);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,boost-freq-khz\n");
+		return ret;
+	}
+	pdata->boost_freq = ret;
+
+	ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-ovp", ovps, 4);
+	if (ret < 0) {
+		dev_err(dev, "failed to parse ti,boost-ovp\n");
+		return ret;
+	}
+	pdata->boost_ovp = ret;
+
+	for_each_child_of_node(dev->of_node, node) {
+		if (!of_node_cmp(node->name, "als"))
+			ret = lm3533_of_parse_als_node(dev, node, pdata);
+		else if (!of_node_cmp(node->name, "backlight"))
+			ret = lm3533_of_parse_bl_node(dev, node, pdata);
+		else if (!of_node_cmp(node->name, "led"))
+			ret = lm3533_of_parse_led_node(dev, node, pdata);
+
+		if (ret < 0) {
+			of_node_put(node);
+			return ret;
+		}
+	}
+
+	dev->platform_data = pdata;
+
+	return 0;
+}
+
 static int lm3533_i2c_probe(struct i2c_client *i2c,
 					const struct i2c_device_id *id)
 {
 	struct lm3533 *lm3533;
+	int ret;
 
 	dev_dbg(&i2c->dev, "%s\n", __func__);
 
@@ -608,6 +866,12 @@ static int lm3533_i2c_probe(struct i2c_client *i2c,
 	lm3533->dev = &i2c->dev;
 	lm3533->irq = i2c->irq;
 
+	if (i2c->dev.of_node) {
+		ret = lm3533_pdata_from_of_node(lm3533->dev);
+		if (ret < 0)
+			return ret;
+	}
+
 	return lm3533_device_init(lm3533);
 }
 
-- 
2.4.2

Re: [PATCH v2 3/3] mfd: lm3533: Support initialization from Device Tree

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 2617 bytes --]

Hi Bjorn,

[auto build test WARNING on ljones-mfd/for-mfd-next -- if it's inappropriate base, please suggest rules for selecting the more suitable base]

url:    https://github.com/0day-ci/linux/commits/Bjorn-Andersson/devicetree-mfd-Add-binding-for-the-TI-LM3533/20151028-003248
config: x86_64-randconfig-x012-201543 (attached as .config)
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All warnings (new ones prefixed by >>):

   In file included from include/uapi/linux/stddef.h:1:0,
                    from include/linux/stddef.h:4,
                    from include/uapi/linux/posix_types.h:4,
                    from include/uapi/linux/types.h:13,
                    from include/linux/types.h:5,
                    from include/linux/list.h:4,
                    from include/linux/module.h:9,
                    from drivers/mfd/lm3533-core.c:14:
   drivers/mfd/lm3533-core.c: In function 'lm3533_pdata_from_of_node':
   drivers/mfd/lm3533-core.c:830:8: error: implicit declaration of function 'of_node_cmp' [-Werror=implicit-function-declaration]
      if (!of_node_cmp(node->name, "als"))
           ^
   include/linux/compiler.h:147:28: note: in definition of macro '__trace_if'
     if (__builtin_constant_p((cond)) ? !!(cond) :   \
                               ^
>> drivers/mfd/lm3533-core.c:830:3: note: in expansion of macro 'if'
      if (!of_node_cmp(node->name, "als"))
      ^
   cc1: some warnings being treated as errors

vim +/if +830 drivers/mfd/lm3533-core.c

   814	
   815		ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-freq-khz", freqs, 2);
   816		if (ret < 0) {
   817			dev_err(dev, "failed to parse ti,boost-freq-khz\n");
   818			return ret;
   819		}
   820		pdata->boost_freq = ret;
   821	
   822		ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-ovp", ovps, 4);
   823		if (ret < 0) {
   824			dev_err(dev, "failed to parse ti,boost-ovp\n");
   825			return ret;
   826		}
   827		pdata->boost_ovp = ret;
   828	
   829		for_each_child_of_node(dev->of_node, node) {
 > 830			if (!of_node_cmp(node->name, "als"))
   831				ret = lm3533_of_parse_als_node(dev, node, pdata);
   832			else if (!of_node_cmp(node->name, "backlight"))
   833				ret = lm3533_of_parse_bl_node(dev, node, pdata);
   834			else if (!of_node_cmp(node->name, "led"))
   835				ret = lm3533_of_parse_led_node(dev, node, pdata);
   836	
   837			if (ret < 0) {
   838				of_node_put(node);

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 19618 bytes --]

Re: [PATCH v2 3/3] mfd: lm3533: Support initialization from Device Tree

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 1389 bytes --]

Hi Bjorn,

[auto build test ERROR on ljones-mfd/for-mfd-next -- if it's inappropriate base, please suggest rules for selecting the more suitable base]

url:    https://github.com/0day-ci/linux/commits/Bjorn-Andersson/devicetree-mfd-Add-binding-for-the-TI-LM3533/20151028-003248
config: x86_64-randconfig-x019-201543 (attached as .config)
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All errors (new ones prefixed by >>):

   drivers/mfd/lm3533-core.c: In function 'lm3533_pdata_from_of_node':
>> drivers/mfd/lm3533-core.c:830:8: error: implicit declaration of function 'of_node_cmp' [-Werror=implicit-function-declaration]
      if (!of_node_cmp(node->name, "als"))
           ^
   cc1: some warnings being treated as errors

vim +/of_node_cmp +830 drivers/mfd/lm3533-core.c

   824			dev_err(dev, "failed to parse ti,boost-ovp\n");
   825			return ret;
   826		}
   827		pdata->boost_ovp = ret;
   828	
   829		for_each_child_of_node(dev->of_node, node) {
 > 830			if (!of_node_cmp(node->name, "als"))
   831				ret = lm3533_of_parse_als_node(dev, node, pdata);
   832			else if (!of_node_cmp(node->name, "backlight"))
   833				ret = lm3533_of_parse_bl_node(dev, node, pdata);

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 25708 bytes --]

Re: [PATCH v2 3/3] mfd: lm3533: Support initialization from Device Tree

[Lee Jones]

On Tue, 27 Oct 2015, Bjorn Andersson wrote:

> Implement Device Tree parsing functions to support initialization of the
> lm3533 drivers.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
> 
> Changes since v1:
> - Added units to bost-freq and als resistance
> 
>  drivers/mfd/lm3533-core.c | 264 ++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 264 insertions(+)

I assume you plan on fixing the build robot's complains? 

> diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c
> index 5abcbb2e8849..9f0fb362ee76 100644
> --- a/drivers/mfd/lm3533-core.c
> +++ b/drivers/mfd/lm3533-core.c
> @@ -18,6 +18,7 @@
>  #include <linux/gpio.h>
>  #include <linux/i2c.h>
>  #include <linux/mfd/core.h>
> +#include <linux/of_gpio.h>
>  #include <linux/regmap.h>
>  #include <linux/seq_file.h>
>  #include <linux/slab.h>
> @@ -25,6 +26,7 @@
>  
>  #include <linux/mfd/lm3533.h>
>  
> +#define LM3533_DEFAULT_BRIGHTNESS	200
>  
>  #define LM3533_BOOST_OVP_MASK		0x06
>  #define LM3533_BOOST_OVP_SHIFT		1
> @@ -588,10 +590,266 @@ static const struct regmap_config regmap_config = {
>  	.precious_reg	= lm3533_precious_register,
>  };
>  
> +static int lm3533_of_parse_enum(struct device_node *node,
> +				const char *propname,
> +				const unsigned *match, size_t num_matches)
> +{
> +	size_t i;
> +	int ret;
> +	u32 val;
> +
> +	ret = of_property_read_u32(node, propname, &val);
> +	if (ret < 0)
> +		return ret;
> +
> +	for (i = 0; i < num_matches; i++) {
> +		if (val == match[i])
> +			return i;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int lm3533_of_parse_pwm_zones(struct device_node *node)
> +{
> +	const char *propname = "ti,pwm-zones";
> +	u32 zones[5];
> +	int count;
> +	int ret;
> +	int i;
> +
> +	count = of_property_count_u32_elems(node, propname);
> +	if (count == -EINVAL)
> +		return 0;
> +	if (count <= 0)
> +		return count;
> +	if (count >= ARRAY_SIZE(zones))
> +		return -EINVAL;
> +
> +	ret = of_property_read_u32_array(node, propname, zones, count);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Enable pwm input, and enable the selected zones */
> +	ret = BIT(0);
> +	for (i = 0; i < count; i++)
> +		ret |= BIT(zones[i] + 1);
> +
> +	return ret;
> +}
> +
> +static int lm3533_of_parse_als_node(struct device *dev,
> +				    struct device_node *node,
> +				    struct lm3533_platform_data *pdata)
> +{
> +	struct lm3533_als_platform_data *als_pdata;
> +	int ret;
> +	u32 val;
> +
> +	als_pdata = devm_kzalloc(dev,
> +				 sizeof(struct lm3533_als_platform_data),
> +				 GFP_KERNEL);
> +	if (!als_pdata)
> +		return -ENOMEM;
> +
> +	als_pdata->pwm_mode = of_property_read_bool(node, "ti,pwm-mode");
> +
> +	ret = of_property_read_u32(node, "ti,als-resistance-ohm", &val);
> +	if (ret < 0 && ret != -EINVAL) {
> +		dev_err(dev, "unable to read ti,als-resistance-ohm");
> +		return ret;
> +	}
> +
> +	/* Leave at high-Z, if the property was omitted or specified as 0 */
> +	if (!ret && val != 0)
> +		als_pdata->r_select = 200000 / val;
> +
> +	pdata->als = als_pdata;
> +
> +	return 0;
> +}
> +
> +static int lm3533_of_parse_bl_node(struct device *dev,
> +				   struct device_node *node,
> +				   struct lm3533_platform_data *pdata)
> +{
> +	struct lm3533_bl_platform_data *bl_pdata;
> +	int ret;
> +	u32 reg;
> +	u32 val;
> +
> +	ret = of_property_read_u32(node, "reg", &reg);
> +	if (ret < 0 || reg >= ARRAY_SIZE(lm3533_bl_devs)) {
> +		dev_err(dev, "invalid reg property\n");
> +		return ret;
> +	}
> +
> +	bl_pdata = &pdata->backlights[reg];
> +
> +	/* Increment num_backlights if we're filling a new space */
> +	if (reg + 1 > pdata->num_backlights)
> +		pdata->num_backlights = reg + 1;
> +
> +	ret = of_property_read_string(node, "label",
> +				      (const char **)&bl_pdata->name);
> +	if (ret < 0) {
> +		dev_err(dev, "unable to parse label\n");
> +		return ret;
> +	}
> +
> +	ret = of_property_read_u32(node, "led-max-microamp", &val);
> +	if (ret < 0) {
> +		dev_err(dev, "unable to parse led-max-microamp\n");
> +		return ret;
> +	}
> +	bl_pdata->max_current = val;
> +
> +	val = LM3533_DEFAULT_BRIGHTNESS;
> +	ret = of_property_read_u32(node, "default-brightness", &val);
> +	if (ret < 0 && ret != -EINVAL) {
> +		dev_err(dev, "unable to parse default-brightness\n");
> +		return ret;
> +	}
> +	bl_pdata->default_brightness = val;
> +
> +	ret = lm3533_of_parse_pwm_zones(node);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to parse ti,pwm-zones\n");
> +		return ret;
> +	}
> +	bl_pdata->pwm = ret;
> +
> +	return 0;
> +}
> +
> +static int lm3533_of_parse_led_node(struct device *dev,
> +				    struct device_node *node,
> +				    struct lm3533_platform_data *pdata)
> +{
> +	struct lm3533_led_platform_data *led_pdata;
> +	int ret;
> +	u32 reg;
> +	u32 val;
> +
> +	ret = of_property_read_u32(node, "reg", &reg);
> +	if (ret < 0 || reg >= ARRAY_SIZE(lm3533_led_devs)) {
> +		dev_err(dev, "invalid reg property\n");
> +		return ret;
> +	}
> +
> +	led_pdata = &pdata->leds[reg];
> +
> +	/* Increment num_leds if we're filling a new space */
> +	if (reg + 1 > pdata->num_leds)
> +		pdata->num_leds = reg + 1;
> +
> +	ret = of_property_read_string(node, "label",
> +				      (const char **)&led_pdata->name);
> +	if (ret < 0) {
> +		dev_err(dev, "unable to parse label\n");
> +		return ret;
> +	}
> +
> +	ret = of_property_read_u32(node, "led-max-microamp", &val);
> +	if (ret < 0) {
> +		dev_err(dev, "unable to parse led-max-microamp\n");
> +		return ret;
> +	}
> +	led_pdata->max_current = val;
> +
> +	ret = of_property_read_string(node, "linux,default-trigger",
> +				      &led_pdata->default_trigger);
> +	if (ret < 0 && ret != -EINVAL) {
> +		dev_err(dev, "unable to parse default-trigger\n");
> +		return ret;
> +	}
> +
> +	ret = lm3533_of_parse_pwm_zones(node);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to parse ti,pwm-zones\n");
> +		return ret;
> +	}
> +	led_pdata->pwm = ret;
> +
> +	return 0;
> +}
> +
> +static int lm3533_pdata_from_of_node(struct device *dev)
> +{
> +	struct lm3533_platform_data *pdata;
> +	struct device_node *node;
> +	int ret;
> +	const unsigned freqs[] = {
> +		[LM3533_BOOST_FREQ_500KHZ] = 500,
> +		[LM3533_BOOST_FREQ_1000KHZ] = 1000,
> +	};
> +	const unsigned ovps[] = {
> +		[LM3533_BOOST_OVP_16V] = 16,
> +		[LM3533_BOOST_OVP_24V] = 24,
> +		[LM3533_BOOST_OVP_32V] = 32,
> +		[LM3533_BOOST_OVP_40V] = 40,
> +	};
> +
> +	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
> +	if (!pdata)
> +		return -ENOMEM;
> +
> +	pdata->backlights = devm_kcalloc(dev,
> +					 ARRAY_SIZE(lm3533_bl_devs),
> +					 sizeof(struct lm3533_bl_platform_data),
> +					 GFP_KERNEL);
> +	if (!pdata->backlights)
> +		return -ENOMEM;
> +
> +	pdata->leds = devm_kcalloc(dev,
> +				   ARRAY_SIZE(lm3533_led_devs),
> +				   sizeof(struct lm3533_led_platform_data),
> +				   GFP_KERNEL);
> +	if (!pdata->leds)
> +		return -ENOMEM;
> +
> +	pdata->gpio_hwen = of_get_named_gpio(dev->of_node, "ti,hwen-gpios", 0);
> +	if (pdata->gpio_hwen < 0)
> +		return pdata->gpio_hwen;
> +
> +	ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-freq-khz", freqs, 2);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to parse ti,boost-freq-khz\n");
> +		return ret;
> +	}
> +	pdata->boost_freq = ret;
> +
> +	ret = lm3533_of_parse_enum(dev->of_node, "ti,boost-ovp", ovps, 4);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to parse ti,boost-ovp\n");
> +		return ret;
> +	}
> +	pdata->boost_ovp = ret;
> +
> +	for_each_child_of_node(dev->of_node, node) {
> +		if (!of_node_cmp(node->name, "als"))
> +			ret = lm3533_of_parse_als_node(dev, node, pdata);
> +		else if (!of_node_cmp(node->name, "backlight"))
> +			ret = lm3533_of_parse_bl_node(dev, node, pdata);
> +		else if (!of_node_cmp(node->name, "led"))
> +			ret = lm3533_of_parse_led_node(dev, node, pdata);
> +
> +		if (ret < 0) {
> +			of_node_put(node);
> +			return ret;
> +		}
> +	}
> +
> +	dev->platform_data = pdata;
> +
> +	return 0;
> +}
> +
>  static int lm3533_i2c_probe(struct i2c_client *i2c,
>  					const struct i2c_device_id *id)
>  {
>  	struct lm3533 *lm3533;
> +	int ret;
>  
>  	dev_dbg(&i2c->dev, "%s\n", __func__);
>  
> @@ -608,6 +866,12 @@ static int lm3533_i2c_probe(struct i2c_client *i2c,
>  	lm3533->dev = &i2c->dev;
>  	lm3533->irq = i2c->irq;
>  
> +	if (i2c->dev.of_node) {
> +		ret = lm3533_pdata_from_of_node(lm3533->dev);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
>  	return lm3533_device_init(lm3533);
>  }
>  

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v2 3/3] mfd: lm3533: Support initialization from Device Tree

[Joe Perches]

On Wed, 2015-10-28 at 11:40 +0000, Lee Jones wrote:
> On Tue, 27 Oct 2015, Bjorn Andersson wrote:
> > Implement Device Tree parsing functions to support initialization of the
> > lm3533 drivers.
[]
> > Changes since v1:
> > - Added units to bost-freq and als resistance
[]
> I assume you plan on fixing the build robot's complains? 

[ then +15 kb of useless quoted stuff ]

Please remember to trim your replies.

Re: [PATCH v2 3/3] mfd: lm3533: Support initialization from Device Tree

[Bjorn Andersson]

On Wed 28 Oct 04:40 PDT 2015, Lee Jones wrote:

> On Tue, 27 Oct 2015, Bjorn Andersson wrote:
> 
> > Implement Device Tree parsing functions to support initialization of the
> > lm3533 drivers.
> > 
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > ---
> > 
> > Changes since v1:
> > - Added units to bost-freq and als resistance
> > 
> >  drivers/mfd/lm3533-core.c | 264 ++++++++++++++++++++++++++++++++++++++++++++++
> >  1 file changed, 264 insertions(+)
> 
> I assume you plan on fixing the build robot's complains? 
> 

I do, unfortunately I didn't get those on v1 :/


Just trying to conclude if I should move the logic from patch 2 into
this patch before resending.

Regards,
Bjorn

Re: [PATCH v2 1/3] devicetree: mfd: Add binding for the TI LM3533

[Rob Herring]

On Tue, Oct 27, 2015 at 11:29 AM, Bjorn Andersson
<bjorn.andersson@sonymobile.com> wrote:
> Add the binding for the Texas Instruments LM3533 lighting power
> solution.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

Acked-by: Rob Herring <robh@kernel.org>

> ---
>
> Changes since v1:
> - Added unit to boost-freq and als-resistance (as the frequency now comes with
>   a unit specifier I changed it to be expressed in kHz)
>
>  Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
>  1 file changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
> new file mode 100644
> index 000000000000..399df39ec7e7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
> @@ -0,0 +1,183 @@
> +Texas Instruments LM3533 binding
> +
> +This binding describes the Texas Instruments LM3533, a lighting power solution
> +for smartphone handsets. The common properties are described directly in the
> +node, while each individual component are described in an optional subnode.
> +
> +- compatible:
> +       Usage: required
> +       Value type: <stringlist>
> +       Definition: must be:
> +                   "ti,lm3533"
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: i2c address of the LM3533 chip
> +
> +- ti,hwen-gpios:
> +       Usage: required
> +       Value type: <prop-encoded-array>
> +       Definition: reference to gpio pin connected to the HWEN input; as
> +                   specified in "gpio/gpio.txt"
> +
> +- ti,als-supply:
> +       Usage: optional
> +       Value type: <prop-encoded-array>
> +       Definition: reference to regulator powering the V_als input; as
> +                   specified in "regulator/regulator.txt"
> +
> +- ti,boost-freq-khz:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: switch-frequency of the boost converter, must be either:
> +                   500 or 1000
> +
> +- ti,boost-ovp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: over voltage protection limit, must be one of: 16, 24, 32
> +                   or 40
> +
> +- #address-cells:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: must be 1
> +
> +- #size-cells:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: must be 0
> +
> += ALS SUBNODE
> +The als subnode must be named "als", it carries the als related properties.
> +
> +- ti,als-resistance-ohm:
> +       Usage: required (unless ti,pwm-mode is specified)
> +       Value type: <u32>
> +       Definition: specifies the resistor value (R_als), in Ohm. Valid values
> +                   ranges from 200kOhm to 1574Ohm.
> +
> +- ti,pwm-mode:
> +       Usage: optional
> +       Value type: <empty>
> +       Definition: specifies, if present, that the als should operate in pwm
> +                   mode - rather than analog mode
> +
> += BACKLIGHT NODES
> +Backlight subnodes must be named "backlight", they carry the backlight related
> +properties.
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies which of the two backlights this node corresponds
> +                   to
> +
> +- default-brightness:
> +       Usage: optional
> +       Value type: <32>
> +       Definition: specifies the default brightness for the backlight, in
> +                   units of brightness [0-255]
> +
> +- label:
> +       Usage: required
> +       Value type: <string>
> +       Definition: specifies a name of this backlight
> +
> +- led-max-microamp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies the max current for this backlight, in uA, as
> +                   described in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +       Usage: optional
> +       Value type: <u32 list>
> +       Definition: lists the ALS zones to be PWM controlled for this backlight,
> +                   the values in the list are in the range [0 - 4]
> +
> += LED NODES
> +LED subnodes must be named "led", they carry the LED related properties.
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies which of the four LEDs this node corresponds to
> +
> +- linux,default-trigger:
> +       Usage: optional
> +       Value type: <string>
> +       Definition: specifies the default trigger for the LED, as described in
> +                   "leds/common.txt"
> +
> +- label:
> +       Usage: required
> +       Value type: <string>
> +       Definition: specifies a name of this LED, as described in
> +                   "leds/common.txt"
> +
> +- led-max-microamp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies the max current for this LED, in uA, as described
> +                   in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +       Usage: optional
> +       Value type: <u32 list>
> +       Definition: lists the ALS zones to be PWM controlled for this LED, the
> +                   values in the list are in the range [0 - 4]
> +
> += EXAMPLE
> +
> +i2c@12460000 {
> +       compatible = "qcom,i2c-qup-v1.1.1";
> +       ...
> +
> +       lm3533@36 {
> +               compatible = "ti,lm3533";
> +               reg = <0x36>;
> +
> +               ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
> +               ti,als-supply = <&pm8921_l11>;
> +
> +               ti,boost-freq = <500000>;
> +               ti,boost-ovp = <24>;
> +
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               als {
> +                       ti,als-resistance = <200000>;
> +               };
> +
> +               backlight@0 {
> +                       reg = <0>;
> +                       label = "backlight";
> +
> +                       led-max-microamp = <20200>;
> +               };
> +
> +               led@0 {
> +                       reg = <0>;
> +                       label = "red";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +
> +               led@1 {
> +                       reg = <1>;
> +                       label = "green";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +
> +               led@2 {
> +                       reg = <2>;
> +                       label = "blue";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +       };
> +
> --
> 2.4.2
>

Re: [PATCH v2 1/3] devicetree: mfd: Add binding for the TI LM3533

[Lee Jones]

On Tue, 27 Oct 2015, Bjorn Andersson wrote:

> Add the binding for the Texas Instruments LM3533 lighting power
> solution.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
> 
> Changes since v1:
> - Added unit to boost-freq and als-resistance (as the frequency now comes with
>   a unit specifier I changed it to be expressed in kHz)
> 
>  Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
>  1 file changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
> new file mode 100644
> index 000000000000..399df39ec7e7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
> @@ -0,0 +1,183 @@
> +Texas Instruments LM3533 binding
> +
> +This binding describes the Texas Instruments LM3533, a lighting power solution
> +for smartphone handsets. The common properties are described directly in the
> +node, while each individual component are described in an optional subnode.
> +
> +- compatible:
> +	Usage: required
> +	Value type: <stringlist>
> +	Definition: must be:
> +		    "ti,lm3533"
> +
> +- reg:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: i2c address of the LM3533 chip
> +
> +- ti,hwen-gpios:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: reference to gpio pin connected to the HWEN input; as
> +		    specified in "gpio/gpio.txt"

Why have you made this a vendor binding?

*-gpios is a generic property.

> +- ti,als-supply:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: reference to regulator powering the V_als input; as
> +		    specified in "regulator/regulator.txt"

Same goes for *-supply.

> +- ti,boost-freq-khz:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: switch-frequency of the boost converter, must be either:
> +		    500 or 1000

Quite a few vendors are using 'boost' now.

Perhaps we need to create a set of generic bindings.

Also, we usually measure DT bindings in HZ, not kHz.

> +- ti,boost-ovp:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: over voltage protection limit, must be one of: 16, 24, 32
> +		    or 40

Is this in volts?  If so, it should be microvolts.

> +- #address-cells:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be 1
> +
> +- #size-cells:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be 0
> +
> += ALS SUBNODE
> +The als subnode must be named "als", it carries the als related properties.

Perfect time to tell us what ALS is/means.

> +- ti,als-resistance-ohm:
> +	Usage: required (unless ti,pwm-mode is specified)
> +	Value type: <u32>
> +	Definition: specifies the resistor value (R_als), in Ohm. Valid values
> +		    ranges from 200kOhm to 1574Ohm.

Might be worth specifying the values which you are actually going to
use here i.e. "200kOhm" is not a valid u32.

> +- ti,pwm-mode:
> +	Usage: optional
> +	Value type: <empty>
> +	Definition: specifies, if present, that the als should operate in pwm

Suggest s/pwm/PWM/

> +		    mode - rather than analog mode
> +
> += BACKLIGHT NODES
> +Backlight subnodes must be named "backlight", they carry the backlight related
> +properties.
> +
> +- reg:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: specifies which of the two backlights this node corresponds
> +		    to
> +
> +- default-brightness:
> +	Usage: optional
> +	Value type: <32>
> +	Definition: specifies the default brightness for the backlight, in
> +		    units of brightness [0-255]
> +
> +- label:
> +	Usage: required
> +	Value type: <string>
> +	Definition: specifies a name of this backlight
> +
> +- led-max-microamp:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: specifies the max current for this backlight, in uA, as
> +		    described in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +	Usage: optional
> +	Value type: <u32 list>
> +	Definition: lists the ALS zones to be PWM controlled for this backlight,
> +		    the values in the list are in the range [0 - 4]
> +

It's usually a good idea to point to where all of the aforementioned
generic properties are documented.  I personally like the format
(See: ../<subsystem>/<binding>.txt)

> += LED NODES
> +LED subnodes must be named "led", they carry the LED related properties.
> +
> +- reg:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: specifies which of the four LEDs this node corresponds to
> +
> +- linux,default-trigger:
> +	Usage: optional
> +	Value type: <string>
> +	Definition: specifies the default trigger for the LED, as described in
> +		    "leds/common.txt"

No such file.  I think you mean "../leds/common/txt".

> +- label:
> +	Usage: required
> +	Value type: <string>
> +	Definition: specifies a name of this LED, as described in
> +		    "leds/common.txt"
> +
> +- led-max-microamp:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: specifies the max current for this LED, in uA, as described
> +		    in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +	Usage: optional
> +	Value type: <u32 list>
> +	Definition: lists the ALS zones to be PWM controlled for this LED, the
> +		    values in the list are in the range [0 - 4]
> +
> += EXAMPLE
> +
> +i2c@12460000 {
> +	compatible = "qcom,i2c-qup-v1.1.1";
> +	...
> +
> +	lm3533@36 {
> +		compatible = "ti,lm3533";
> +		reg = <0x36>;
> +
> +		ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
> +		ti,als-supply = <&pm8921_l11>;
> +
> +		ti,boost-freq = <500000>;
> +		ti,boost-ovp = <24>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		als {
> +			ti,als-resistance = <200000>;
> +		};
> +
> +		backlight@0 {
> +			reg = <0>;
> +			label = "backlight";
> +
> +			led-max-microamp = <20200>;
> +		};
> +
> +		led@0 {
> +			reg = <0>;
> +			label = "red";
> +
> +			led-max-microamp = <5000>;
> +		};
> +
> +		led@1 {
> +			reg = <1>;
> +			label = "green";
> +
> +			led-max-microamp = <5000>;
> +		};
> +
> +		led@2 {
> +			reg = <2>;
> +			label = "blue";
> +
> +			led-max-microamp = <5000>;
> +		};
> +	};
> +

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v2 1/3] devicetree: mfd: Add binding for the TI LM3533

[Bjorn Andersson]

On Fri 30 Oct 11:42 PDT 2015, Lee Jones wrote:

Rob, please see the discussion regarding ti,boost-freq-khz below. Should
we both specify unit at the same time as we use standard units? (This is
not the first time I have to change this back and forth)

> On Tue, 27 Oct 2015, Bjorn Andersson wrote:
> 
[..]
> > +- ti,hwen-gpios:
> > +	Usage: required
> > +	Value type: <prop-encoded-array>
> > +	Definition: reference to gpio pin connected to the HWEN input; as
> > +		    specified in "gpio/gpio.txt"
> 
> Why have you made this a vendor binding?
> 
> *-gpios is a generic property.
> 

Because the hwen gpio is a ti lm3533 specific thing, but I get what
you're saying. Will drop the prefix.

> > +- ti,als-supply:
> > +	Usage: optional
> > +	Value type: <prop-encoded-array>
> > +	Definition: reference to regulator powering the V_als input; as
> > +		    specified in "regulator/regulator.txt"
> 
> Same goes for *-supply.
> 

Same here

> > +- ti,boost-freq-khz:
> > +	Usage: required
> > +	Value type: <u32>
> > +	Definition: switch-frequency of the boost converter, must be either:
> > +		    500 or 1000
> 
> Quite a few vendors are using 'boost' now.
> 

The ti,boost-low-freq from the bq25890 binding is the only other
property I can find that describes the same thing. So I'm not sure I
follow you here.

> Perhaps we need to create a set of generic bindings.
> 
> Also, we usually measure DT bindings in HZ, not kHz.
> 

I thought we had defined frequencies to be in HZ and HZ only, but then
Rob's comment that I need to actually specify the unit doesn't make any
sense.

Do we want these properties in a standard unit or do we want them
specifying the unit? Having both seems excessive.

> > +- ti,boost-ovp:
> > +	Usage: required
> > +	Value type: <u32>
> > +	Definition: over voltage protection limit, must be one of: 16, 24, 32
> > +		    or 40
> 
> Is this in volts?  If so, it should be microvolts.
> 

Okay, will update.

[..]
> > += ALS SUBNODE
> > +The als subnode must be named "als", it carries the als related properties.
> 
> Perfect time to tell us what ALS is/means.
> 

You're right, I'll expand this.

> > +- ti,als-resistance-ohm:
> > +	Usage: required (unless ti,pwm-mode is specified)
> > +	Value type: <u32>
> > +	Definition: specifies the resistor value (R_als), in Ohm. Valid values
> > +		    ranges from 200kOhm to 1574Ohm.
> 
> Might be worth specifying the values which you are actually going to
> use here i.e. "200kOhm" is not a valid u32.
> 

I'll drop the units.

> > +- ti,pwm-mode:
> > +	Usage: optional
> > +	Value type: <empty>
> > +	Definition: specifies, if present, that the als should operate in pwm
> 
> Suggest s/pwm/PWM/
> 

OK

[..]
> > +- ti,pwm-zones:
> > +	Usage: optional
> > +	Value type: <u32 list>
> > +	Definition: lists the ALS zones to be PWM controlled for this backlight,
> > +		    the values in the list are in the range [0 - 4]
> > +
> 
> It's usually a good idea to point to where all of the aforementioned
> generic properties are documented.  I personally like the format
> (See: ../<subsystem>/<binding>.txt)
> 

OK

> > += LED NODES

Regards,
Bjorn

Re: [PATCH v2 1/3] devicetree: mfd: Add binding for the TI LM3533

[Rob Herring]

On Fri, Oct 30, 2015 at 2:41 PM, Bjorn Andersson
<bjorn.andersson@sonymobile.com> wrote:
> On Fri 30 Oct 11:42 PDT 2015, Lee Jones wrote:
>
> Rob, please see the discussion regarding ti,boost-freq-khz below. Should
> we both specify unit at the same time as we use standard units? (This is
> not the first time I have to change this back and forth)
>
>> On Tue, 27 Oct 2015, Bjorn Andersson wrote:
>>
> [..]
>> > +- ti,hwen-gpios:
>> > +   Usage: required
>> > +   Value type: <prop-encoded-array>
>> > +   Definition: reference to gpio pin connected to the HWEN input; as
>> > +               specified in "gpio/gpio.txt"
>>
>> Why have you made this a vendor binding?
>>
>> *-gpios is a generic property.
>>
>
> Because the hwen gpio is a ti lm3533 specific thing, but I get what
> you're saying. Will drop the prefix.

Actually, that is fine. -gpios is common, but the rest is specific to
a binding. But if it is a common function, then a common name would be
fine. Enable gpios are common for example.

>> > +- ti,als-supply:
>> > +   Usage: optional
>> > +   Value type: <prop-encoded-array>
>> > +   Definition: reference to regulator powering the V_als input; as
>> > +               specified in "regulator/regulator.txt"
>>
>> Same goes for *-supply.
>>
>
> Same here
>
>> > +- ti,boost-freq-khz:
>> > +   Usage: required
>> > +   Value type: <u32>
>> > +   Definition: switch-frequency of the boost converter, must be either:
>> > +               500 or 1000
>>
>> Quite a few vendors are using 'boost' now.
>>
>
> The ti,boost-low-freq from the bq25890 binding is the only other
> property I can find that describes the same thing. So I'm not sure I
> follow you here.
>
>> Perhaps we need to create a set of generic bindings.
>>
>> Also, we usually measure DT bindings in HZ, not kHz.

Surprisingly, there are not enough examples to draw much conclusion.

> I thought we had defined frequencies to be in HZ and HZ only, but then
> Rob's comment that I need to actually specify the unit doesn't make any
> sense.

I don't think we decided, but let's decide now. Go with Hz.

Really, I first prefer the property name has units and second having
standardized units. But if there is a common property without units, I
prefer that even more.

> Do we want these properties in a standard unit or do we want them
> specifying the unit? Having both seems excessive.

You mean "freq" would imply the units? No, we want the actual units in
the property.

Rob

Re: [PATCH v2 1/3] devicetree: mfd: Add binding for the TI LM3533

[Bjorn Andersson]

On Fri 30 Oct 13:18 PDT 2015, Rob Herring wrote:

> On Fri, Oct 30, 2015 at 2:41 PM, Bjorn Andersson
> <bjorn.andersson@sonymobile.com> wrote:
> > On Fri 30 Oct 11:42 PDT 2015, Lee Jones wrote:
> >
> > Rob, please see the discussion regarding ti,boost-freq-khz below. Should
> > we both specify unit at the same time as we use standard units? (This is
> > not the first time I have to change this back and forth)
> >
> >> On Tue, 27 Oct 2015, Bjorn Andersson wrote:
> >>
[..]
> > The ti,boost-low-freq from the bq25890 binding is the only other
> > property I can find that describes the same thing. So I'm not sure I
> > follow you here.
> >
> >> Perhaps we need to create a set of generic bindings.
> >>
> >> Also, we usually measure DT bindings in HZ, not kHz.
> 
> Surprisingly, there are not enough examples to draw much conclusion.
> 
> > I thought we had defined frequencies to be in HZ and HZ only, but then
> > Rob's comment that I need to actually specify the unit doesn't make any
> > sense.
> 
> I don't think we decided, but let's decide now. Go with Hz.
> 

+1

> Really, I first prefer the property name has units and second having
> standardized units. But if there is a common property without units, I
> prefer that even more.
> 

You can find this property in a variety of hardware, but I don't think
it would make much sense to define this single property in a common
place today.

This seems to be the first case where we specify the unit on one of
these properties though.

> > Do we want these properties in a standard unit or do we want them
> > specifying the unit? Having both seems excessive.
> 
> You mean "freq" would imply the units? No, we want the actual units in
> the property.
> 

You're right, frequency can be measured in other units than Hz, I can't
think of one that would be applicable here though.

Either way, I'll slap on a unit to the property name - Hz that is...

Thanks for your input.

Regards,
Bjorn