From: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: "David S . Miller" <davem@davemloft.net>
Cc: Allan Nielsen <Allan.Nielsen@microsemi.com>,
razvan.stefanescu@nxp.com, po.liu@nxp.com,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-mips@linux-mips.org,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Rob Herring <robh+dt@kernel.org>
Subject: [PATCH net-next 4/8] dt-bindings: net: add DT bindings for Microsemi Ocelot Switch
Date: Fri, 23 Mar 2018 21:11:13 +0100 [thread overview]
Message-ID: <20180323201117.8416-5-alexandre.belloni@bootlin.com> (raw)
In-Reply-To: <20180323201117.8416-1-alexandre.belloni@bootlin.com>
DT bindings for the Ethernet switch found on Microsemi Ocelot platforms.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
.../devicetree/bindings/net/mscc-ocelot.txt | 62 ++++++++++++++++++++++
1 file changed, 62 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/mscc-ocelot.txt
diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt
new file mode 100644
index 000000000000..ee092a85b5a0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt
@@ -0,0 +1,62 @@
+Microsemi Ocelot network Switch
+===============================
+
+The Microsemi Ocelot network switch can be found on Microsemi SoCs (VSC7513,
+VSC7514)
+
+Required properties:
+- compatible: Should be "mscc,ocelot-switch"
+- reg: Must contain an (offset, length) pair of the register set for each
+ entry in reg-names.
+- reg-names: Must include the following entries:
+ - "sys"
+ - "rew"
+ - "qs"
+ - "hsio"
+ - "qsys"
+ - "ana"
+ - "portX" with X from 0 to the number of last port index available on that
+ switch
+- interrupts: Should contain the switch interrupts for frame extraction and
+ frame injection
+- interrupt-names: should contain the interrupt names: "xtr", "inj"
+
+Example:
+
+ switch@1010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "mscc,ocelot-switch";
+ reg = <0x1010000 0x10000>,
+ <0x1030000 0x10000>,
+ <0x1080000 0x100>,
+ <0x10d0000 0x10000>,
+ <0x11e0000 0x100>,
+ <0x11f0000 0x100>,
+ <0x1200000 0x100>,
+ <0x1210000 0x100>,
+ <0x1220000 0x100>,
+ <0x1230000 0x100>,
+ <0x1240000 0x100>,
+ <0x1250000 0x100>,
+ <0x1260000 0x100>,
+ <0x1270000 0x100>,
+ <0x1280000 0x100>,
+ <0x1800000 0x80000>,
+ <0x1880000 0x10000>;
+ reg-names = "sys", "rew", "qs", "hsio", "port0",
+ "port1", "port2", "port3", "port4", "port5",
+ "port6", "port7", "port8", "port9", "port10",
+ "qsys", "ana";
+ interrupts = <21 22>;
+ interrupt-names = "xtr", "inj";
+
+ port0: port@0 {
+ reg = <0>;
+ phy-handle = <&phy0>;
+ };
+ port1: port@1 {
+ reg = <1>;
+ phy-handle = <&phy1>;
+ };
+ };
--
2.16.2
next prev parent reply other threads:[~2018-03-23 20:14 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-03-23 20:11 [PATCH net-next 0/8] Microsemi Ocelot switch support Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 1/8] net: phy: Add initial support for Microsemi Ocelot internal PHYs Alexandre Belloni
2018-03-23 20:29 ` Andrew Lunn
2018-03-23 21:08 ` Florian Fainelli
2018-03-28 16:18 ` Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 2/8] dt-bindings: net: add DT bindings for Microsemi MIIM Alexandre Belloni
2018-03-23 21:46 ` Florian Fainelli
2018-03-23 20:11 ` [PATCH net-next 3/8] net: mscc: Add MDIO driver Alexandre Belloni
2018-03-23 20:49 ` Andrew Lunn
2018-03-29 14:05 ` Alexandre Belloni
2018-03-29 14:40 ` Andrew Lunn
2018-03-29 14:53 ` Alexandre Belloni
2018-03-29 14:57 ` Andrew Lunn
2018-03-23 21:51 ` Florian Fainelli
2018-03-29 14:14 ` Alexandre Belloni
2018-03-23 20:11 ` Alexandre Belloni [this message]
2018-03-23 21:01 ` [PATCH net-next 4/8] dt-bindings: net: add DT bindings for Microsemi Ocelot Switch Andrew Lunn
2018-03-23 21:11 ` Florian Fainelli
2018-03-26 22:25 ` Rob Herring
2018-03-26 22:50 ` Andrew Lunn
2018-03-27 0:34 ` Rob Herring
2018-03-26 22:25 ` Rob Herring
2018-03-23 20:11 ` [PATCH net-next 5/8] net: mscc: Add initial Ocelot switch support Alexandre Belloni
2018-03-23 21:25 ` Andrew Lunn
2018-03-23 21:41 ` Florian Fainelli
2018-03-30 12:45 ` Alexandre Belloni
2018-03-30 13:54 ` Andrew Lunn
2018-03-30 14:16 ` Alexandre Belloni
2018-03-30 14:50 ` Andrew Lunn
2018-03-31 22:47 ` Florian Fainelli
2018-04-24 18:52 ` Alexandre Belloni
2018-03-26 19:13 ` kbuild test robot
2018-03-30 7:02 ` Razvan Stefanescu
2018-03-23 20:11 ` [PATCH net-next 6/8] MIPS: mscc: Add switch to ocelot Alexandre Belloni
2018-03-23 21:17 ` Florian Fainelli
2018-03-23 21:22 ` Alexandre Belloni
2018-03-23 21:33 ` Andrew Lunn
2018-03-23 21:44 ` Florian Fainelli
2018-03-23 22:06 ` Andrew Lunn
2018-03-23 22:11 ` Florian Fainelli
2018-03-24 14:48 ` Andrew Lunn
2018-03-23 20:11 ` [PATCH net-next 7/8] MIPS: mscc: connect phys to ports on ocelot_pcb123 Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 8/8] MAINTAINERS: Add entry for Microsemi Ethernet switches Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180323201117.8416-5-alexandre.belloni@bootlin.com \
--to=alexandre.belloni@bootlin.com \
--cc=Allan.Nielsen@microsemi.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=netdev@vger.kernel.org \
--cc=po.liu@nxp.com \
--cc=razvan.stefanescu@nxp.com \
--cc=robh+dt@kernel.org \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).