From: Rob Herring <robh@kernel.org>
To: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: "David S . Miller" <davem@davemloft.net>,
Allan Nielsen <Allan.Nielsen@microsemi.com>,
razvan.stefanescu@nxp.com, po.liu@nxp.com,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-mips@linux-mips.org
Subject: Re: [PATCH net-next 4/8] dt-bindings: net: add DT bindings for Microsemi Ocelot Switch
Date: Mon, 26 Mar 2018 17:25:26 -0500 [thread overview]
Message-ID: <20180326222526.gwflhl4m5bawdh7f@rob-hp-laptop> (raw)
In-Reply-To: <20180323201117.8416-5-alexandre.belloni@bootlin.com>
On Fri, Mar 23, 2018 at 09:11:13PM +0100, Alexandre Belloni wrote:
> DT bindings for the Ethernet switch found on Microsemi Ocelot platforms.
>
> Cc: Rob Herring <robh+dt@kernel.org>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
> ---
> .../devicetree/bindings/net/mscc-ocelot.txt | 62 ++++++++++++++++++++++
> 1 file changed, 62 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/mscc-ocelot.txt
>
> diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt
> new file mode 100644
> index 000000000000..ee092a85b5a0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt
> @@ -0,0 +1,62 @@
> +Microsemi Ocelot network Switch
> +===============================
> +
> +The Microsemi Ocelot network switch can be found on Microsemi SoCs (VSC7513,
> +VSC7514)
What's the difference in these SoCs? You should probably have the
part#'s in the compatible string.
> +
> +Required properties:
> +- compatible: Should be "mscc,ocelot-switch"
> +- reg: Must contain an (offset, length) pair of the register set for each
> + entry in reg-names.
> +- reg-names: Must include the following entries:
> + - "sys"
> + - "rew"
> + - "qs"
> + - "hsio"
> + - "qsys"
> + - "ana"
> + - "portX" with X from 0 to the number of last port index available on that
> + switch
> +- interrupts: Should contain the switch interrupts for frame extraction and
> + frame injection
> +- interrupt-names: should contain the interrupt names: "xtr", "inj"
> +
> +Example:
> +
> + switch@1010000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "mscc,ocelot-switch";
> + reg = <0x1010000 0x10000>,
> + <0x1030000 0x10000>,
> + <0x1080000 0x100>,
> + <0x10d0000 0x10000>,
> + <0x11e0000 0x100>,
> + <0x11f0000 0x100>,
> + <0x1200000 0x100>,
> + <0x1210000 0x100>,
> + <0x1220000 0x100>,
> + <0x1230000 0x100>,
> + <0x1240000 0x100>,
> + <0x1250000 0x100>,
> + <0x1260000 0x100>,
> + <0x1270000 0x100>,
> + <0x1280000 0x100>,
> + <0x1800000 0x80000>,
> + <0x1880000 0x10000>;
> + reg-names = "sys", "rew", "qs", "hsio", "port0",
> + "port1", "port2", "port3", "port4", "port5",
> + "port6", "port7", "port8", "port9", "port10",
> + "qsys", "ana";
> + interrupts = <21 22>;
> + interrupt-names = "xtr", "inj";
> +
> + port0: port@0 {
> + reg = <0>;
> + phy-handle = <&phy0>;
> + };
> + port1: port@1 {
> + reg = <1>;
> + phy-handle = <&phy1>;
> + };
> + };
> --
> 2.16.2
>
next prev parent reply other threads:[~2018-03-26 22:25 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-03-23 20:11 [PATCH net-next 0/8] Microsemi Ocelot switch support Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 1/8] net: phy: Add initial support for Microsemi Ocelot internal PHYs Alexandre Belloni
2018-03-23 20:29 ` Andrew Lunn
2018-03-23 21:08 ` Florian Fainelli
2018-03-28 16:18 ` Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 2/8] dt-bindings: net: add DT bindings for Microsemi MIIM Alexandre Belloni
2018-03-23 21:46 ` Florian Fainelli
2018-03-23 20:11 ` [PATCH net-next 3/8] net: mscc: Add MDIO driver Alexandre Belloni
2018-03-23 20:49 ` Andrew Lunn
2018-03-29 14:05 ` Alexandre Belloni
2018-03-29 14:40 ` Andrew Lunn
2018-03-29 14:53 ` Alexandre Belloni
2018-03-29 14:57 ` Andrew Lunn
2018-03-23 21:51 ` Florian Fainelli
2018-03-29 14:14 ` Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 4/8] dt-bindings: net: add DT bindings for Microsemi Ocelot Switch Alexandre Belloni
2018-03-23 21:01 ` Andrew Lunn
2018-03-23 21:11 ` Florian Fainelli
2018-03-26 22:25 ` Rob Herring
2018-03-26 22:50 ` Andrew Lunn
2018-03-27 0:34 ` Rob Herring
2018-03-26 22:25 ` Rob Herring [this message]
2018-03-23 20:11 ` [PATCH net-next 5/8] net: mscc: Add initial Ocelot switch support Alexandre Belloni
2018-03-23 21:25 ` Andrew Lunn
2018-03-23 21:41 ` Florian Fainelli
2018-03-30 12:45 ` Alexandre Belloni
2018-03-30 13:54 ` Andrew Lunn
2018-03-30 14:16 ` Alexandre Belloni
2018-03-30 14:50 ` Andrew Lunn
2018-03-31 22:47 ` Florian Fainelli
2018-04-24 18:52 ` Alexandre Belloni
2018-03-26 19:13 ` kbuild test robot
2018-03-30 7:02 ` Razvan Stefanescu
2018-03-23 20:11 ` [PATCH net-next 6/8] MIPS: mscc: Add switch to ocelot Alexandre Belloni
2018-03-23 21:17 ` Florian Fainelli
2018-03-23 21:22 ` Alexandre Belloni
2018-03-23 21:33 ` Andrew Lunn
2018-03-23 21:44 ` Florian Fainelli
2018-03-23 22:06 ` Andrew Lunn
2018-03-23 22:11 ` Florian Fainelli
2018-03-24 14:48 ` Andrew Lunn
2018-03-23 20:11 ` [PATCH net-next 7/8] MIPS: mscc: connect phys to ports on ocelot_pcb123 Alexandre Belloni
2018-03-23 20:11 ` [PATCH net-next 8/8] MAINTAINERS: Add entry for Microsemi Ethernet switches Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180326222526.gwflhl4m5bawdh7f@rob-hp-laptop \
--to=robh@kernel.org \
--cc=Allan.Nielsen@microsemi.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=netdev@vger.kernel.org \
--cc=po.liu@nxp.com \
--cc=razvan.stefanescu@nxp.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).