* [PATCH 0/3] Driver for UCS1002
@ 2019-04-17 8:44 Andrey Smirnov
2019-04-17 8:44 ` [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant Andrey Smirnov
` (2 more replies)
0 siblings, 3 replies; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-17 8:44 UTC (permalink / raw)
To: linux-pm
Cc: Andrey Smirnov, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Sebastian Reichel, linux-kernel
Everyone:
This small series adds a driver for UCS1002 Programmable USB Port
Power Controller with Charger Emulation. See [page] for product page
and [datasheet] for device dataseet. Hopefully each individual patch
is self explanatory.
Feedback is welcome!
Thanks,
Andrey Smirnov
[page] https://www.microchip.com/wwwproducts/en/UCS1002-2
[datasheet] https://ww1.microchip.com/downloads/en/DeviceDoc/UCS1002-2%20Data%20Sheet.pdf
Andrey Smirnov (3):
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
.../power/supply/microchip,ucs1002.txt | 26 +
drivers/power/supply/Kconfig | 9 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/power_supply_sysfs.c | 2 +-
drivers/power/supply/ucs1002_power.c | 639 ++++++++++++++++++
include/linux/power_supply.h | 1 +
6 files changed, 677 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt
create mode 100644 drivers/power/supply/ucs1002_power.c
--
2.20.1
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
2019-04-17 8:44 [PATCH 0/3] Driver for UCS1002 Andrey Smirnov
@ 2019-04-17 8:44 ` Andrey Smirnov
2019-04-26 16:12 ` Guenter Roeck
2019-04-17 8:44 ` [PATCH 2/3] power: supply: Add driver for Microchip UCS1002 Andrey Smirnov
2019-04-17 8:44 ` [PATCH 3/3] dt-bindings: power: supply: Add bindings " Andrey Smirnov
2 siblings, 1 reply; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-17 8:44 UTC (permalink / raw)
To: linux-pm
Cc: Andrey Smirnov, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Sebastian Reichel, linux-kernel
Add POWER_SUPPLY_HEALTH_OVERCURRENT constant in order to allow
singalling overcurrent condition via power supply health information.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Health <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
---
drivers/power/supply/power_supply_sysfs.c | 2 +-
include/linux/power_supply.h | 1 +
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/power/supply/power_supply_sysfs.c b/drivers/power/supply/power_supply_sysfs.c
index 5e91946731fd..464f4e837601 100644
--- a/drivers/power/supply/power_supply_sysfs.c
+++ b/drivers/power/supply/power_supply_sysfs.c
@@ -62,7 +62,7 @@ static const char * const power_supply_charge_type_text[] = {
static const char * const power_supply_health_text[] = {
"Unknown", "Good", "Overheat", "Dead", "Over voltage",
"Unspecified failure", "Cold", "Watchdog timer expire",
- "Safety timer expire"
+ "Safety timer expire", "Over current"
};
static const char * const power_supply_technology_text[] = {
diff --git a/include/linux/power_supply.h b/include/linux/power_supply.h
index 2f9c201a54d1..bdab14c7ca4d 100644
--- a/include/linux/power_supply.h
+++ b/include/linux/power_supply.h
@@ -57,6 +57,7 @@ enum {
POWER_SUPPLY_HEALTH_COLD,
POWER_SUPPLY_HEALTH_WATCHDOG_TIMER_EXPIRE,
POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE,
+ POWER_SUPPLY_HEALTH_OVERCURRENT,
};
enum {
--
2.20.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-17 8:44 [PATCH 0/3] Driver for UCS1002 Andrey Smirnov
2019-04-17 8:44 ` [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant Andrey Smirnov
@ 2019-04-17 8:44 ` Andrey Smirnov
2019-04-26 14:43 ` Lucas Stach
` (2 more replies)
2019-04-17 8:44 ` [PATCH 3/3] dt-bindings: power: supply: Add bindings " Andrey Smirnov
2 siblings, 3 replies; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-17 8:44 UTC (permalink / raw)
To: linux-pm
Cc: Andrey Smirnov, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Sebastian Reichel, linux-kernel
Add driver for Microchip UCS1002 Programmable USB Port Power
Controller with Charger Emulation. The driver exposed a power supply
device to control/monitor various parameter of the device as well as a
regulator to allow controlling VBUS line.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Health <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
---
drivers/power/supply/Kconfig | 9 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/ucs1002_power.c | 639 +++++++++++++++++++++++++++
3 files changed, 649 insertions(+)
create mode 100644 drivers/power/supply/ucs1002_power.c
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index e901b9879e7e..c614c8a196f3 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
Say Y here to enable support for fuel gauge with SC27XX
PMIC chips.
+config CHARGER_UCS1002
+ tristate "Microchip UCS1002 USB Port Power Controller"
+ depends on I2C
+ depends on OF
+ select REGMAP_I2C
+ help
+ Say Y to enable support for Microchip UCS1002 Programmable
+ USB Port Power Controller with Charger Emulation.
+
endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index b731c2a9b695..c56803a9e4fe 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
+obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c
new file mode 100644
index 000000000000..b0b81d62e003
--- /dev/null
+++ b/drivers/power/supply/ucs1002_power.c
@@ -0,0 +1,639 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for UCS1002 Programmable USB Port Power Controller
+ *
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+#include <linux/freezer.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+/* UCS1002 Registers */
+#define UCS1002_REG_CURRENT_MEASUREMENT 0x00
+
+/*
+ * The Total Accumulated Charge registers store the total accumulated
+ * charge delivered from the VS source to a portable device. The total
+ * value is calculated using four registers, from 01h to 04h. The bit
+ * weighting of the registers is given in mA/hrs.
+ */
+#define UCS1002_REG_TOTAL_ACC_CHARGE 0x01
+
+/* Other Status Register */
+#define UCS1002_REG_OTHER_STATUS 0x0f
+# define F_ADET_PIN BIT(4)
+# define F_CHG_ACT BIT(3)
+
+/* Interrupt Status */
+#define UCS1002_REG_INTERRUPT_STATUS 0x10
+# define F_DISCHARGE_ERR BIT(6)
+# define F_RESET BIT(5)
+# define F_MIN_KEEP_OUT BIT(4)
+# define F_TSD BIT(3)
+# define F_OVER_VOLT BIT(2)
+# define F_BACK_VOLT BIT(1)
+# define F_OVER_ILIM BIT(0)
+
+/* Pin Status Register */
+#define UCS1002_REG_PIN_STATUS 0x14
+# define UCS1002_PWR_STATE_MASK 0x03
+# define F_PWR_EN_PIN BIT(6)
+# define F_M2_PIN BIT(5)
+# define F_M1_PIN BIT(4)
+# define F_EM_EN_PIN BIT(3)
+# define F_SEL_PIN BIT(2)
+# define F_ACTIVE_MODE_MASK GENMASK(5, 3)
+# define F_ACTIVE_MODE_PASSTHROUGH F_M2_PIN
+# define F_ACTIVE_MODE_DEDICATED F_EM_EN_PIN
+# define F_ACTIVE_MODE_BC12_DCP (F_M2_PIN | F_EM_EN_PIN)
+# define F_ACTIVE_MODE_BC12_SDP F_M1_PIN
+# define F_ACTIVE_MODE_BC12_CDP (F_M1_PIN | F_M2_PIN | F_EM_EN_PIN)
+
+/* General Configuration Register */
+#define UCS1002_REG_GENERAL_CFG 0x15
+# define F_RATION_EN BIT(3)
+
+/* Emulation Configuration Register */
+#define UCS1002_REG_EMU_CFG 0x16
+
+/* Switch Configuration Register */
+#define UCS1002_REG_SWITCH_CFG 0x17
+# define F_PIN_IGNORE BIT(7)
+# define F_EM_EN_SET BIT(5)
+# define F_M2_SET BIT(4)
+# define F_M1_SET BIT(3)
+# define F_S0_SET BIT(2)
+# define F_PWR_EN_SET BIT(1)
+# define F_LATCH_SET BIT(0)
+# define V_SET_ACTIVE_MODE_MASK GENMASK(5, 3)
+# define V_SET_ACTIVE_MODE_PASSTHROUGH F_M2_SET
+# define V_SET_ACTIVE_MODE_DEDICATED F_EM_EN_SET
+# define V_SET_ACTIVE_MODE_BC12_DCP (F_M2_SET | F_EM_EN_SET)
+# define V_SET_ACTIVE_MODE_BC12_SDP F_M1_SET
+# define V_SET_ACTIVE_MODE_BC12_CDP (F_M1_SET | F_M2_SET | F_EM_EN_SET)
+
+/* Current Limit Register */
+#define UCS1002_REG_ILIMIT 0x19
+# define UCS1002_ILIM_SW_MASK GENMASK(3, 0)
+
+/* Product ID */
+#define UCS1002_REG_PRODUCT_ID 0xfd
+# define UCS1002_PRODUCT_ID 0x4e
+
+/* Manufacture name */
+#define UCS1002_MANUFACTURER "SMSC"
+
+struct ucs1002_info {
+ struct power_supply *charger;
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct regulator_desc *regulator_descriptor;
+ bool present;
+};
+
+static enum power_supply_property ucs1002_props[] = {
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_CHARGE_NOW,
+ POWER_SUPPLY_PROP_CURRENT_NOW,
+ POWER_SUPPLY_PROP_CURRENT_MAX,
+ POWER_SUPPLY_PROP_PRESENT, /* the presence of PED */
+ POWER_SUPPLY_PROP_MANUFACTURER,
+ POWER_SUPPLY_PROP_USB_TYPE,
+ POWER_SUPPLY_PROP_HEALTH,
+};
+
+static int ucs1002_get_online(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®);
+ if (ret)
+ return ret;
+
+ val->intval = !!(reg & F_CHG_ACT);
+
+ return 0;
+}
+
+static int ucs1002_get_charge(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ /*
+ * To fit within 32 bits some values are rounded (uA/h)
+ *
+ * For Total Accumulated Charge Middle Low Byte register, addr
+ * 03h, byte 2
+ *
+ * B0: 0.01084 mA/h rounded to 11 uA/h
+ * B1: 0.02169 mA/h rounded to 22 uA/h
+ * B2: 0.04340 mA/h rounded to 43 uA/h
+ * B3: 0.08676 mA/h rounded to 87 uA/h
+ * B4: 0.17350 mA/h rounded to 173 uÁ/h
+ *
+ * For Total Accumulated Charge Low Byte register, addr 04h,
+ * byte 3
+ *
+ * B6: 0.00271 mA/h rounded to 3 uA/h
+ * B7: 0.005422 mA/h rounded to 5 uA/h
+ */
+ static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
+ 0, 0, 0, 0, 0, 0, 3, 5,
+
+ 11, 22, 43, 87, 173, 347, 694, 1388,
+
+ 2776, 5552, 11105, 22210, 44420, 88840, 177700, 355400,
+
+ 710700, 1421000, 2843000, 5685000, 11371000, 22742000,
+ 45484000, 90968000,
+ };
+ unsigned long total_acc_charger;
+ unsigned int reg;
+ int i, ret;
+
+ ret = regmap_bulk_read(info->regmap, UCS1002_REG_TOTAL_ACC_CHARGE,
+ ®, sizeof(u32));
+ if (ret)
+ return ret;
+
+ total_acc_charger = be32_to_cpu(reg);
+ val->intval = 0;
+
+ for_each_set_bit(i, &total_acc_charger, ARRAY_SIZE(bit_weights_uAh))
+ val->intval += bit_weights_uAh[i];
+
+ return 0;
+}
+
+static int ucs1002_get_current(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ /*
+ * The Current Measurement register stores the measured
+ * current value delivered to the portable device. The range
+ * is from 9.76 mA to 2.5 A.
+ */
+ static const int bit_weights_uA[BITS_PER_TYPE(u8)] = {
+ 9760, 19500, 39000, 78100, 156200, 312300, 624600, 1249300,
+ };
+ unsigned long current_measurement;
+ unsigned int reg;
+ int i, ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_CURRENT_MEASUREMENT, ®);
+ if (ret)
+ return ret;
+
+ current_measurement = reg;
+ val->intval = 0;
+
+ for_each_set_bit(i, ¤t_measurement, ARRAY_SIZE(bit_weights_uA))
+ val->intval += bit_weights_uA[i];
+
+ return 0;
+}
+
+/*
+ * The Current Limit register stores the maximum current used by the
+ * port switch. The range is from 500mA to 2.5 A.
+ */
+static const u32 ucs1002_current_limit_uA[] = {
+ 500000, 900000, 1000000, 1200000, 1500000, 1800000, 2000000, 2500000,
+};
+
+static int ucs1002_get_max_current(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
+ if (ret)
+ return ret;
+
+ val->intval = ucs1002_current_limit_uA[reg & UCS1002_ILIM_SW_MASK];
+
+ return 0;
+}
+
+static int ucs1002_set_max_current(struct ucs1002_info *info, u32 val)
+{
+ unsigned int reg;
+ int ret, idx;
+
+ for (idx = 0; idx < ARRAY_SIZE(ucs1002_current_limit_uA); idx++) {
+ if (val == ucs1002_current_limit_uA[idx])
+ break;
+ }
+
+ if (idx == ARRAY_SIZE(ucs1002_current_limit_uA)) {
+ dev_err(&info->client->dev,
+ "%d is an invalid max current value\n", val);
+ return -EINVAL;
+ }
+
+ ret = regmap_write(info->regmap, UCS1002_REG_ILIMIT, idx);
+ if (ret)
+ return ret;
+ /*
+ * Any current limit setting exceeding the one set via ILIM
+ * pin will be rejected, so we read out freshly changed limit
+ * to make sure that it took effect.
+ */
+ ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
+ if (ret)
+ return ret;
+
+ if (reg != idx)
+ return -EINVAL;
+
+ return 0;
+}
+
+static enum power_supply_usb_type ucs1002_usb_types[] = {
+ POWER_SUPPLY_USB_TYPE_PD,
+ POWER_SUPPLY_USB_TYPE_SDP,
+ POWER_SUPPLY_USB_TYPE_DCP,
+ POWER_SUPPLY_USB_TYPE_CDP,
+ POWER_SUPPLY_USB_TYPE_UNKNOWN,
+};
+
+static int ucs1002_set_usb_type(struct ucs1002_info *info, int val)
+{
+ unsigned int mode;
+
+ if (val >= ARRAY_SIZE(ucs1002_usb_types))
+ return -EINVAL;
+
+ switch (ucs1002_usb_types[val]) {
+ case POWER_SUPPLY_USB_TYPE_PD:
+ mode = V_SET_ACTIVE_MODE_DEDICATED;
+ break;
+ case POWER_SUPPLY_USB_TYPE_SDP:
+ mode = V_SET_ACTIVE_MODE_BC12_SDP;
+ break;
+ case POWER_SUPPLY_USB_TYPE_DCP:
+ mode = V_SET_ACTIVE_MODE_BC12_DCP;
+ break;
+ case POWER_SUPPLY_USB_TYPE_CDP:
+ mode = V_SET_ACTIVE_MODE_BC12_CDP;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
+ V_SET_ACTIVE_MODE_MASK, mode);
+}
+
+static int ucs1002_get_usb_type(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ enum power_supply_usb_type type;
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®);
+ if (ret)
+ return ret;
+
+ switch (reg & F_ACTIVE_MODE_MASK) {
+ default:
+ type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
+ break;
+ case F_ACTIVE_MODE_DEDICATED:
+ type = POWER_SUPPLY_USB_TYPE_PD;
+ break;
+ case F_ACTIVE_MODE_BC12_SDP:
+ type = POWER_SUPPLY_USB_TYPE_SDP;
+ break;
+ case F_ACTIVE_MODE_BC12_DCP:
+ type = POWER_SUPPLY_USB_TYPE_DCP;
+ break;
+ case F_ACTIVE_MODE_BC12_CDP:
+ type = POWER_SUPPLY_USB_TYPE_CDP;
+ break;
+ };
+
+ val->intval = type;
+
+ return 0;
+}
+
+static int ucs1002_get_health(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ unsigned int reg;
+ int ret, health;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_INTERRUPT_STATUS, ®);
+ if (ret)
+ return ret;
+
+ if (reg & F_TSD)
+ health = POWER_SUPPLY_HEALTH_OVERHEAT;
+ else if (reg & (F_OVER_VOLT | F_BACK_VOLT))
+ health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ else if (reg & F_OVER_ILIM)
+ health = POWER_SUPPLY_HEALTH_OVERCURRENT;
+ else if (reg & (F_DISCHARGE_ERR | F_MIN_KEEP_OUT))
+ health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+ else
+ health = POWER_SUPPLY_HEALTH_GOOD;
+
+ val->intval = health;
+
+ return 0;
+}
+
+static int ucs1002_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct ucs1002_info *info = power_supply_get_drvdata(psy);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_ONLINE:
+ return ucs1002_get_online(info, val);
+ case POWER_SUPPLY_PROP_CHARGE_NOW:
+ return ucs1002_get_charge(info, val);
+ case POWER_SUPPLY_PROP_CURRENT_NOW:
+ return ucs1002_get_current(info, val);
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ return ucs1002_get_max_current(info, val);
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ return ucs1002_get_usb_type(info, val);
+ case POWER_SUPPLY_PROP_HEALTH:
+ return ucs1002_get_health(info, val);
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = info->present;
+ return 0;
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = UCS1002_MANUFACTURER;
+ return 0;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int ucs1002_set_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ const union power_supply_propval *val)
+{
+ struct ucs1002_info *info = power_supply_get_drvdata(psy);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ return ucs1002_set_max_current(info, val->intval);
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ return ucs1002_set_usb_type(info, val->intval);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int ucs1002_property_is_writeable(struct power_supply *psy,
+ enum power_supply_property psp)
+{
+ switch (psp) {
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct power_supply_desc ucs1002_charger_desc = {
+ .name = "ucs1002",
+ .type = POWER_SUPPLY_TYPE_USB,
+ .usb_types = ucs1002_usb_types,
+ .num_usb_types = ARRAY_SIZE(ucs1002_usb_types),
+ .get_property = ucs1002_get_property,
+ .set_property = ucs1002_set_property,
+ .property_is_writeable = ucs1002_property_is_writeable,
+ .properties = ucs1002_props,
+ .num_properties = ARRAY_SIZE(ucs1002_props),
+};
+
+static irqreturn_t ucs1002_charger_irq(int irq, void *data)
+{
+ int ret, regval;
+ bool present;
+ struct ucs1002_info *info = data;
+
+ present = info->present;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®val);
+ if (ret)
+ return IRQ_HANDLED;
+
+ /* update attached status */
+ info->present = (regval & F_ADET_PIN) ? true : false;
+
+ /* notify the change */
+ if (present != info->present)
+ power_supply_changed(info->charger);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t ucs1002_alert_irq(int irq, void *data)
+{
+ struct ucs1002_info *info = data;
+
+ power_supply_changed(info->charger);
+
+ return IRQ_HANDLED;
+}
+
+static const struct regulator_ops ucs1002_regulator_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+};
+
+static const struct regulator_desc ucs1002_regulator_descriptor = {
+ .name = "ucs1002-vbus",
+ .ops = &ucs1002_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .enable_reg = UCS1002_REG_SWITCH_CFG,
+ .enable_mask = F_PWR_EN_SET,
+ .enable_val = F_PWR_EN_SET,
+ .fixed_uV = 5000000,
+ .n_voltages = 1,
+};
+
+static int ucs1002_probe(struct i2c_client *client,
+ const struct i2c_device_id *dev_id)
+{
+ struct device *dev = &client->dev;
+ struct power_supply_config charger_config = {};
+ const struct regmap_config regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ };
+ struct regulator_config regulator_config = {};
+ int irq_a_det, irq_alert, ret;
+ struct regulator_dev *rdev;
+ struct ucs1002_info *info;
+ unsigned int regval;
+
+ info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ info->regmap = devm_regmap_init_i2c(client, ®map_config);
+ if (IS_ERR(info->regmap)) {
+ ret = PTR_ERR(info->regmap);
+ dev_err(dev, "regmap initialization failed: %d\n", ret);
+ return ret;
+ }
+
+ info->client = client;
+
+ irq_a_det = of_irq_get_byname(dev->of_node, "a_det");
+ irq_alert = of_irq_get_byname(dev->of_node, "alert");
+
+ charger_config.of_node = dev->of_node;
+ charger_config.drv_data = info;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_PRODUCT_ID, ®val);
+ if (ret)
+ return ret;
+
+ if (regval != UCS1002_PRODUCT_ID) {
+ dev_err(dev,
+ "Product ID does not match (0x%02x != 0x%02x)\n",
+ regval, UCS1002_PRODUCT_ID);
+ return -ENODEV;
+ }
+
+ dev_info(dev, "registered with product id 0x%02x\n", regval);
+
+ /* Enable charge rationing by default */
+ ret = regmap_update_bits(info->regmap, UCS1002_REG_GENERAL_CFG,
+ F_RATION_EN, F_RATION_EN);
+ if (ret)
+ return ret;
+
+ dev_dbg(dev, "set active mode selection through i2c\n");
+ /*
+ * Ignore the M1, M2, PWR_EN, and EM_EN pin states. Set active
+ * mode selection to Dedicated Charger Emulation Cycle.
+ *
+ * #M1 #M2 EM_EN
+ * 0 0 1 - Dedicated Charger Emulation Cycle
+ *
+ */
+ ret = regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
+ F_PIN_IGNORE | F_EM_EN_SET | F_M2_SET |
+ F_M1_SET, F_PIN_IGNORE | F_EM_EN_SET);
+ if (ret)
+ return ret;
+ /*
+ * Be safe and set initial current limit to 500mA
+ */
+ ret = ucs1002_set_max_current(info, 500000);
+ if (ret) {
+ dev_err(dev, "Failed to read max current default\n");
+ return ret;
+ }
+
+ info->charger = devm_power_supply_register(dev, &ucs1002_charger_desc,
+ &charger_config);
+ if (IS_ERR(info->charger)) {
+ dev_err(dev, "failed to register power supply\n");
+ return PTR_ERR(info->charger);
+ }
+
+ ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®val);
+ if (ret)
+ return ret;
+
+ info->regulator_descriptor =
+ devm_kmemdup(dev, &ucs1002_regulator_descriptor,
+ sizeof(ucs1002_regulator_descriptor),
+ GFP_KERNEL);
+ info->regulator_descriptor->enable_is_inverted = !(regval & F_SEL_PIN);
+
+ regulator_config.dev = dev;
+ regulator_config.of_node = dev->of_node;
+ regulator_config.regmap = info->regmap;
+
+ rdev = devm_regulator_register(dev, info->regulator_descriptor,
+ ®ulator_config);
+ if (IS_ERR(rdev)) {
+ dev_err(dev, "failed to register VBUS regulator\n");
+ return PTR_ERR(rdev);
+ }
+
+ if (irq_a_det > 0) {
+ ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
+ ucs1002_charger_irq,
+ IRQF_TRIGGER_FALLING |
+ IRQF_TRIGGER_RISING |
+ IRQF_ONESHOT,
+ "ucs1002-a_det", info);
+ if (ret) {
+ dev_err(dev, "failed to request A_DET threaded irq\n");
+ return ret;
+ }
+ }
+
+ if (irq_alert > 0) {
+ ret = devm_request_threaded_irq(dev, irq_alert, NULL,
+ ucs1002_alert_irq,
+ IRQF_TRIGGER_FALLING |
+ IRQF_TRIGGER_RISING |
+ IRQF_ONESHOT,
+ "ucs1002-alert", info);
+ if (ret) {
+ dev_err(dev, "failed to request ALERT threaded irq\n");
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id ucs1002_of_match[] = {
+ { .compatible = "microchip,ucs1002", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ucs1002_of_match);
+#endif
+
+static const struct i2c_device_id ucs1002_ids[] = {
+ {"ucs1002", 0},
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(i2c, ucs1002_ids);
+
+static struct i2c_driver ucs1002_driver = {
+ .driver = {
+ .name = "ucs1002",
+ .of_match_table = of_match_ptr(ucs1002_of_match),
+ },
+ .probe = ucs1002_probe,
+};
+module_i2c_driver(ucs1002_driver);
+
+MODULE_DESCRIPTION("Microchip UCS1002 Programmable USB Port Power Controller");
+MODULE_AUTHOR("Enric Balletbo Serra <enric.balletbo@collabora.com>");
+MODULE_AUTHOR("Andrey Smirnov <andrew.smirnov@gmail.com>");
+MODULE_LICENSE("GPL v2");
--
2.20.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 3/3] dt-bindings: power: supply: Add bindings for Microchip UCS1002
2019-04-17 8:44 [PATCH 0/3] Driver for UCS1002 Andrey Smirnov
2019-04-17 8:44 ` [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant Andrey Smirnov
2019-04-17 8:44 ` [PATCH 2/3] power: supply: Add driver for Microchip UCS1002 Andrey Smirnov
@ 2019-04-17 8:44 ` Andrey Smirnov
2019-04-17 19:05 ` Fabio Estevam
2 siblings, 1 reply; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-17 8:44 UTC (permalink / raw)
To: linux-pm
Cc: Andrey Smirnov, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Rob Herring, devicetree, Sebastian Reichel,
linux-kernel
Add bindings for Microchip UCS1002 Programmable USB Port Power
Controller with Charger Emulation.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Health <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
---
.../power/supply/microchip,ucs1002.txt | 26 +++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt
diff --git a/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt
new file mode 100644
index 000000000000..bef5be47d73e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt
@@ -0,0 +1,26 @@
+Microchip UCS1002 USB Port Power Controller
+
+Required properties:
+- compatible : Should be "microchip,ucs1002";
+- reg : I2C slave address
+
+Optional properties:
+- interrupts-extended : A list of interrupts lines present (could be either
+ corresponding to A_DET# pin, ALERT# pin, or both)
+- interrupt-names : A list of interrupt names. Should contain (if
+ present):
+ - "a_det" for line connected to A_DET# pin
+ - "alert" for line connected to ALERT# pin
+Example:
+
+&i2c3 {
+ charger@32 {
+ compatible = "microchip,ucs1002";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ucs1002_pins>;
+ reg = <0x32>;
+ interrupts-extended = <&gpio5 2 IRQ_TYPE_NONE>,
+ <&gpio3 21 IRQ_TYPE_NONE>;
+ interrupt-names = "a_det", "alert";
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH 3/3] dt-bindings: power: supply: Add bindings for Microchip UCS1002
2019-04-17 8:44 ` [PATCH 3/3] dt-bindings: power: supply: Add bindings " Andrey Smirnov
@ 2019-04-17 19:05 ` Fabio Estevam
0 siblings, 0 replies; 13+ messages in thread
From: Fabio Estevam @ 2019-04-17 19:05 UTC (permalink / raw)
To: Andrey Smirnov
Cc: linux-pm, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Rob Herring,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Sebastian Reichel, linux-kernel
Hi Andrey,
On Wed, Apr 17, 2019 at 5:46 AM Andrey Smirnov <andrew.smirnov@gmail.com> wrote:
>
> Add bindings for Microchip UCS1002 Programmable USB Port Power
> Controller with Charger Emulation.
>
> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> Cc: Chris Health <cphealy@gmail.com>
It seems there is a typo in Chris' last name.
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-17 8:44 ` [PATCH 2/3] power: supply: Add driver for Microchip UCS1002 Andrey Smirnov
@ 2019-04-26 14:43 ` Lucas Stach
2019-04-28 22:24 ` Andrey Smirnov
2019-04-26 16:10 ` Guenter Roeck
2019-04-26 16:51 ` Enric Balletbo Serra
2 siblings, 1 reply; 13+ messages in thread
From: Lucas Stach @ 2019-04-26 14:43 UTC (permalink / raw)
To: Andrey Smirnov, linux-pm
Cc: Chris Health, Fabio Estevam, Guenter Roeck, Sebastian Reichel,
linux-kernel
Hi Andrey,
Am Mittwoch, den 17.04.2019, 01:44 -0700 schrieb Andrey Smirnov:
> Add driver for Microchip UCS1002 Programmable USB Port Power
> Controller with Charger Emulation. The driver exposed a power supply
> device to control/monitor various parameter of the device as well as a
> regulator to allow controlling VBUS line.
>
> > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> > Cc: Chris Health <cphealy@gmail.com>
> > Cc: Lucas Stach <l.stach@pengutronix.de>
> > Cc: Fabio Estevam <fabio.estevam@nxp.com>
> > Cc: Guenter Roeck <linux@roeck-us.net>
> > Cc: Sebastian Reichel <sre@kernel.org>
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-pm@vger.kernel.org
> ---
[...]
> + if (irq_a_det > 0) {
> > + ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
> > + ucs1002_charger_irq,
> > + IRQF_TRIGGER_FALLING |
> > + IRQF_TRIGGER_RISING |
> > + IRQF_ONESHOT,
> > + "ucs1002-a_det", info);
> > + if (ret) {
> > + dev_err(dev, "failed to request A_DET threaded irq\n");
> > + return ret;
> > + }
> > + }
> +
> > + if (irq_alert > 0) {
> > + ret = devm_request_threaded_irq(dev, irq_alert, NULL,
> > + ucs1002_alert_irq,
> > + IRQF_TRIGGER_FALLING |
> > + IRQF_TRIGGER_RISING |
> > + IRQF_ONESHOT,
> > + "ucs1002-alert", info);
> > + if (ret) {
> > + dev_err(dev, "failed to request ALERT threaded irq\n");
> > + return ret;
> > + }
> > + }
Any reason to explicitly set the IRQ trigger type here? Normally I
would expect this to be set via the DT interrupt specifier.
Regards,
Lucas
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-17 8:44 ` [PATCH 2/3] power: supply: Add driver for Microchip UCS1002 Andrey Smirnov
2019-04-26 14:43 ` Lucas Stach
@ 2019-04-26 16:10 ` Guenter Roeck
2019-04-27 0:16 ` Andrey Smirnov
2019-04-26 16:51 ` Enric Balletbo Serra
2 siblings, 1 reply; 13+ messages in thread
From: Guenter Roeck @ 2019-04-26 16:10 UTC (permalink / raw)
To: Andrey Smirnov
Cc: linux-pm, Chris Health, Lucas Stach, Fabio Estevam,
Sebastian Reichel, linux-kernel
On Wed, Apr 17, 2019 at 01:44:56AM -0700, Andrey Smirnov wrote:
> Add driver for Microchip UCS1002 Programmable USB Port Power
> Controller with Charger Emulation. The driver exposed a power supply
> device to control/monitor various parameter of the device as well as a
> regulator to allow controlling VBUS line.
>
> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> Cc: Chris Health <cphealy@gmail.com>
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Guenter Roeck <linux@roeck-us.net>
> Cc: Sebastian Reichel <sre@kernel.org>
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-pm@vger.kernel.org
> ---
> drivers/power/supply/Kconfig | 9 +
> drivers/power/supply/Makefile | 1 +
> drivers/power/supply/ucs1002_power.c | 639 +++++++++++++++++++++++++++
> 3 files changed, 649 insertions(+)
> create mode 100644 drivers/power/supply/ucs1002_power.c
>
> diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
> index e901b9879e7e..c614c8a196f3 100644
> --- a/drivers/power/supply/Kconfig
> +++ b/drivers/power/supply/Kconfig
> @@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
> Say Y here to enable support for fuel gauge with SC27XX
> PMIC chips.
>
> +config CHARGER_UCS1002
> + tristate "Microchip UCS1002 USB Port Power Controller"
> + depends on I2C
> + depends on OF
> + select REGMAP_I2C
> + help
> + Say Y to enable support for Microchip UCS1002 Programmable
> + USB Port Power Controller with Charger Emulation.
> +
> endif # POWER_SUPPLY
> diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
> index b731c2a9b695..c56803a9e4fe 100644
> --- a/drivers/power/supply/Makefile
> +++ b/drivers/power/supply/Makefile
> @@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
> obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
> obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
> obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
> +obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
> diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c
> new file mode 100644
> index 000000000000..b0b81d62e003
> --- /dev/null
> +++ b/drivers/power/supply/ucs1002_power.c
> @@ -0,0 +1,639 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Driver for UCS1002 Programmable USB Port Power Controller
> + *
> + * Copyright (C) 2019 Zodiac Inflight Innovations
> + */
> +#include <linux/freezer.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/kthread.h>
> +#include <linux/device.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/power_supply.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/of_regulator.h>
> +
You probably want to include linux/bits.h as well.
> +/* UCS1002 Registers */
> +#define UCS1002_REG_CURRENT_MEASUREMENT 0x00
> +
> +/*
> + * The Total Accumulated Charge registers store the total accumulated
> + * charge delivered from the VS source to a portable device. The total
> + * value is calculated using four registers, from 01h to 04h. The bit
> + * weighting of the registers is given in mA/hrs.
> + */
> +#define UCS1002_REG_TOTAL_ACC_CHARGE 0x01
> +
> +/* Other Status Register */
> +#define UCS1002_REG_OTHER_STATUS 0x0f
> +# define F_ADET_PIN BIT(4)
> +# define F_CHG_ACT BIT(3)
> +
> +/* Interrupt Status */
> +#define UCS1002_REG_INTERRUPT_STATUS 0x10
> +# define F_DISCHARGE_ERR BIT(6)
> +# define F_RESET BIT(5)
> +# define F_MIN_KEEP_OUT BIT(4)
> +# define F_TSD BIT(3)
> +# define F_OVER_VOLT BIT(2)
> +# define F_BACK_VOLT BIT(1)
> +# define F_OVER_ILIM BIT(0)
> +
> +/* Pin Status Register */
> +#define UCS1002_REG_PIN_STATUS 0x14
> +# define UCS1002_PWR_STATE_MASK 0x03
> +# define F_PWR_EN_PIN BIT(6)
> +# define F_M2_PIN BIT(5)
> +# define F_M1_PIN BIT(4)
> +# define F_EM_EN_PIN BIT(3)
> +# define F_SEL_PIN BIT(2)
> +# define F_ACTIVE_MODE_MASK GENMASK(5, 3)
> +# define F_ACTIVE_MODE_PASSTHROUGH F_M2_PIN
> +# define F_ACTIVE_MODE_DEDICATED F_EM_EN_PIN
> +# define F_ACTIVE_MODE_BC12_DCP (F_M2_PIN | F_EM_EN_PIN)
> +# define F_ACTIVE_MODE_BC12_SDP F_M1_PIN
> +# define F_ACTIVE_MODE_BC12_CDP (F_M1_PIN | F_M2_PIN | F_EM_EN_PIN)
> +
> +/* General Configuration Register */
> +#define UCS1002_REG_GENERAL_CFG 0x15
> +# define F_RATION_EN BIT(3)
> +
> +/* Emulation Configuration Register */
> +#define UCS1002_REG_EMU_CFG 0x16
> +
> +/* Switch Configuration Register */
> +#define UCS1002_REG_SWITCH_CFG 0x17
> +# define F_PIN_IGNORE BIT(7)
> +# define F_EM_EN_SET BIT(5)
> +# define F_M2_SET BIT(4)
> +# define F_M1_SET BIT(3)
> +# define F_S0_SET BIT(2)
> +# define F_PWR_EN_SET BIT(1)
> +# define F_LATCH_SET BIT(0)
> +# define V_SET_ACTIVE_MODE_MASK GENMASK(5, 3)
> +# define V_SET_ACTIVE_MODE_PASSTHROUGH F_M2_SET
> +# define V_SET_ACTIVE_MODE_DEDICATED F_EM_EN_SET
> +# define V_SET_ACTIVE_MODE_BC12_DCP (F_M2_SET | F_EM_EN_SET)
> +# define V_SET_ACTIVE_MODE_BC12_SDP F_M1_SET
> +# define V_SET_ACTIVE_MODE_BC12_CDP (F_M1_SET | F_M2_SET | F_EM_EN_SET)
> +
> +/* Current Limit Register */
> +#define UCS1002_REG_ILIMIT 0x19
> +# define UCS1002_ILIM_SW_MASK GENMASK(3, 0)
> +
> +/* Product ID */
> +#define UCS1002_REG_PRODUCT_ID 0xfd
> +# define UCS1002_PRODUCT_ID 0x4e
> +
> +/* Manufacture name */
> +#define UCS1002_MANUFACTURER "SMSC"
> +
> +struct ucs1002_info {
> + struct power_supply *charger;
> + struct i2c_client *client;
> + struct regmap *regmap;
> + struct regulator_desc *regulator_descriptor;
> + bool present;
> +};
> +
> +static enum power_supply_property ucs1002_props[] = {
> + POWER_SUPPLY_PROP_ONLINE,
> + POWER_SUPPLY_PROP_CHARGE_NOW,
> + POWER_SUPPLY_PROP_CURRENT_NOW,
> + POWER_SUPPLY_PROP_CURRENT_MAX,
> + POWER_SUPPLY_PROP_PRESENT, /* the presence of PED */
> + POWER_SUPPLY_PROP_MANUFACTURER,
> + POWER_SUPPLY_PROP_USB_TYPE,
> + POWER_SUPPLY_PROP_HEALTH,
> +};
> +
> +static int ucs1002_get_online(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®);
> + if (ret)
> + return ret;
> +
> + val->intval = !!(reg & F_CHG_ACT);
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_charge(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + /*
> + * To fit within 32 bits some values are rounded (uA/h)
> + *
> + * For Total Accumulated Charge Middle Low Byte register, addr
> + * 03h, byte 2
> + *
> + * B0: 0.01084 mA/h rounded to 11 uA/h
> + * B1: 0.02169 mA/h rounded to 22 uA/h
> + * B2: 0.04340 mA/h rounded to 43 uA/h
> + * B3: 0.08676 mA/h rounded to 87 uA/h
> + * B4: 0.17350 mA/h rounded to 173 uÁ/h
> + *
> + * For Total Accumulated Charge Low Byte register, addr 04h,
> + * byte 3
> + *
> + * B6: 0.00271 mA/h rounded to 3 uA/h
> + * B7: 0.005422 mA/h rounded to 5 uA/h
> + */
> + static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
> + 0, 0, 0, 0, 0, 0, 3, 5,
> +
> + 11, 22, 43, 87, 173, 347, 694, 1388,
> +
> + 2776, 5552, 11105, 22210, 44420, 88840, 177700, 355400,
> +
> + 710700, 1421000, 2843000, 5685000, 11371000, 22742000,
> + 45484000, 90968000,
> + };
> + unsigned long total_acc_charger;
> + unsigned int reg;
> + int i, ret;
> +
> + ret = regmap_bulk_read(info->regmap, UCS1002_REG_TOTAL_ACC_CHARGE,
> + ®, sizeof(u32));
> + if (ret)
> + return ret;
> +
> + total_acc_charger = be32_to_cpu(reg);
> + val->intval = 0;
> +
> + for_each_set_bit(i, &total_acc_charger, ARRAY_SIZE(bit_weights_uAh))
> + val->intval += bit_weights_uAh[i];
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_current(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + /*
> + * The Current Measurement register stores the measured
> + * current value delivered to the portable device. The range
> + * is from 9.76 mA to 2.5 A.
> + */
> + static const int bit_weights_uA[BITS_PER_TYPE(u8)] = {
> + 9760, 19500, 39000, 78100, 156200, 312300, 624600, 1249300,
> + };
> + unsigned long current_measurement;
> + unsigned int reg;
> + int i, ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_CURRENT_MEASUREMENT, ®);
> + if (ret)
> + return ret;
> +
> + current_measurement = reg;
> + val->intval = 0;
> +
> + for_each_set_bit(i, ¤t_measurement, ARRAY_SIZE(bit_weights_uA))
> + val->intval += bit_weights_uA[i];
> +
> + return 0;
> +}
> +
> +/*
> + * The Current Limit register stores the maximum current used by the
> + * port switch. The range is from 500mA to 2.5 A.
> + */
> +static const u32 ucs1002_current_limit_uA[] = {
> + 500000, 900000, 1000000, 1200000, 1500000, 1800000, 2000000, 2500000,
> +};
> +
> +static int ucs1002_get_max_current(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> + if (ret)
> + return ret;
> +
> + val->intval = ucs1002_current_limit_uA[reg & UCS1002_ILIM_SW_MASK];
> +
> + return 0;
> +}
> +
> +static int ucs1002_set_max_current(struct ucs1002_info *info, u32 val)
> +{
> + unsigned int reg;
> + int ret, idx;
> +
> + for (idx = 0; idx < ARRAY_SIZE(ucs1002_current_limit_uA); idx++) {
> + if (val == ucs1002_current_limit_uA[idx])
> + break;
> + }
> +
> + if (idx == ARRAY_SIZE(ucs1002_current_limit_uA)) {
> + dev_err(&info->client->dev,
> + "%d is an invalid max current value\n", val);
Here the error message is displayed as result of an attempt to set the current
limit, which presumably can happen from userspace. This is inconsistent with
the error returns below. I am not sure I understand why this would warrant an
error log, but exceeding the limit set with the ILIM pin doesn't. I would
suggest to drop this error message.
> + return -EINVAL;
> + }
> +
> + ret = regmap_write(info->regmap, UCS1002_REG_ILIMIT, idx);
> + if (ret)
> + return ret;
> + /*
> + * Any current limit setting exceeding the one set via ILIM
> + * pin will be rejected, so we read out freshly changed limit
> + * to make sure that it took effect.
> + */
> + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> + if (ret)
> + return ret;
> +
> + if (reg != idx)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static enum power_supply_usb_type ucs1002_usb_types[] = {
> + POWER_SUPPLY_USB_TYPE_PD,
> + POWER_SUPPLY_USB_TYPE_SDP,
> + POWER_SUPPLY_USB_TYPE_DCP,
> + POWER_SUPPLY_USB_TYPE_CDP,
> + POWER_SUPPLY_USB_TYPE_UNKNOWN,
> +};
> +
> +static int ucs1002_set_usb_type(struct ucs1002_info *info, int val)
> +{
> + unsigned int mode;
> +
> + if (val >= ARRAY_SIZE(ucs1002_usb_types))
> + return -EINVAL;
> +
> + switch (ucs1002_usb_types[val]) {
> + case POWER_SUPPLY_USB_TYPE_PD:
> + mode = V_SET_ACTIVE_MODE_DEDICATED;
> + break;
> + case POWER_SUPPLY_USB_TYPE_SDP:
> + mode = V_SET_ACTIVE_MODE_BC12_SDP;
> + break;
> + case POWER_SUPPLY_USB_TYPE_DCP:
> + mode = V_SET_ACTIVE_MODE_BC12_DCP;
> + break;
> + case POWER_SUPPLY_USB_TYPE_CDP:
> + mode = V_SET_ACTIVE_MODE_BC12_CDP;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> + V_SET_ACTIVE_MODE_MASK, mode);
> +}
> +
> +static int ucs1002_get_usb_type(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + enum power_supply_usb_type type;
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®);
> + if (ret)
> + return ret;
> +
> + switch (reg & F_ACTIVE_MODE_MASK) {
> + default:
> + type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
> + break;
> + case F_ACTIVE_MODE_DEDICATED:
> + type = POWER_SUPPLY_USB_TYPE_PD;
> + break;
> + case F_ACTIVE_MODE_BC12_SDP:
> + type = POWER_SUPPLY_USB_TYPE_SDP;
> + break;
> + case F_ACTIVE_MODE_BC12_DCP:
> + type = POWER_SUPPLY_USB_TYPE_DCP;
> + break;
> + case F_ACTIVE_MODE_BC12_CDP:
> + type = POWER_SUPPLY_USB_TYPE_CDP;
> + break;
> + };
> +
> + val->intval = type;
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_health(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + unsigned int reg;
> + int ret, health;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_INTERRUPT_STATUS, ®);
> + if (ret)
> + return ret;
> +
> + if (reg & F_TSD)
> + health = POWER_SUPPLY_HEALTH_OVERHEAT;
> + else if (reg & (F_OVER_VOLT | F_BACK_VOLT))
> + health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> + else if (reg & F_OVER_ILIM)
> + health = POWER_SUPPLY_HEALTH_OVERCURRENT;
> + else if (reg & (F_DISCHARGE_ERR | F_MIN_KEEP_OUT))
> + health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> + else
> + health = POWER_SUPPLY_HEALTH_GOOD;
> +
> + val->intval = health;
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_property(struct power_supply *psy,
> + enum power_supply_property psp,
> + union power_supply_propval *val)
> +{
> + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_ONLINE:
> + return ucs1002_get_online(info, val);
> + case POWER_SUPPLY_PROP_CHARGE_NOW:
> + return ucs1002_get_charge(info, val);
> + case POWER_SUPPLY_PROP_CURRENT_NOW:
> + return ucs1002_get_current(info, val);
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + return ucs1002_get_max_current(info, val);
> + case POWER_SUPPLY_PROP_USB_TYPE:
> + return ucs1002_get_usb_type(info, val);
> + case POWER_SUPPLY_PROP_HEALTH:
> + return ucs1002_get_health(info, val);
> + case POWER_SUPPLY_PROP_PRESENT:
> + val->intval = info->present;
> + return 0;
> + case POWER_SUPPLY_PROP_MANUFACTURER:
> + val->strval = UCS1002_MANUFACTURER;
> + return 0;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int ucs1002_set_property(struct power_supply *psy,
> + enum power_supply_property psp,
> + const union power_supply_propval *val)
> +{
> + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + return ucs1002_set_max_current(info, val->intval);
> + case POWER_SUPPLY_PROP_USB_TYPE:
> + return ucs1002_set_usb_type(info, val->intval);
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int ucs1002_property_is_writeable(struct power_supply *psy,
> + enum power_supply_property psp)
> +{
> + switch (psp) {
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + case POWER_SUPPLY_PROP_USB_TYPE:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static const struct power_supply_desc ucs1002_charger_desc = {
> + .name = "ucs1002",
> + .type = POWER_SUPPLY_TYPE_USB,
> + .usb_types = ucs1002_usb_types,
> + .num_usb_types = ARRAY_SIZE(ucs1002_usb_types),
> + .get_property = ucs1002_get_property,
> + .set_property = ucs1002_set_property,
> + .property_is_writeable = ucs1002_property_is_writeable,
> + .properties = ucs1002_props,
> + .num_properties = ARRAY_SIZE(ucs1002_props),
> +};
> +
> +static irqreturn_t ucs1002_charger_irq(int irq, void *data)
> +{
> + int ret, regval;
> + bool present;
> + struct ucs1002_info *info = data;
> +
> + present = info->present;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®val);
> + if (ret)
> + return IRQ_HANDLED;
> +
> + /* update attached status */
> + info->present = (regval & F_ADET_PIN) ? true : false;
!!(regval & F_ADET_PIN);
would do.
> +
> + /* notify the change */
> + if (present != info->present)
> + power_supply_changed(info->charger);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t ucs1002_alert_irq(int irq, void *data)
> +{
> + struct ucs1002_info *info = data;
> +
> + power_supply_changed(info->charger);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static const struct regulator_ops ucs1002_regulator_ops = {
> + .is_enabled = regulator_is_enabled_regmap,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> +};
> +
> +static const struct regulator_desc ucs1002_regulator_descriptor = {
> + .name = "ucs1002-vbus",
> + .ops = &ucs1002_regulator_ops,
> + .type = REGULATOR_VOLTAGE,
> + .owner = THIS_MODULE,
> + .enable_reg = UCS1002_REG_SWITCH_CFG,
> + .enable_mask = F_PWR_EN_SET,
> + .enable_val = F_PWR_EN_SET,
> + .fixed_uV = 5000000,
> + .n_voltages = 1,
> +};
> +
> +static int ucs1002_probe(struct i2c_client *client,
> + const struct i2c_device_id *dev_id)
> +{
> + struct device *dev = &client->dev;
> + struct power_supply_config charger_config = {};
> + const struct regmap_config regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + };
> + struct regulator_config regulator_config = {};
> + int irq_a_det, irq_alert, ret;
> + struct regulator_dev *rdev;
> + struct ucs1002_info *info;
> + unsigned int regval;
> +
> + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> + if (!info)
> + return -ENOMEM;
> +
> + info->regmap = devm_regmap_init_i2c(client, ®map_config);
> + if (IS_ERR(info->regmap)) {
> + ret = PTR_ERR(info->regmap);
> + dev_err(dev, "regmap initialization failed: %d\n", ret);
> + return ret;
> + }
> +
> + info->client = client;
> +
> + irq_a_det = of_irq_get_byname(dev->of_node, "a_det");
> + irq_alert = of_irq_get_byname(dev->of_node, "alert");
> +
> + charger_config.of_node = dev->of_node;
> + charger_config.drv_data = info;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_PRODUCT_ID, ®val);
> + if (ret)
> + return ret;
Silent error ?
> +
> + if (regval != UCS1002_PRODUCT_ID) {
> + dev_err(dev,
> + "Product ID does not match (0x%02x != 0x%02x)\n",
> + regval, UCS1002_PRODUCT_ID);
> + return -ENODEV;
> + }
> +
> + dev_info(dev, "registered with product id 0x%02x\n", regval);
> +
Does that add any value ? After all, the displayed value is known to be
UCS1002_PRODUCT_ID. It is also not really registered yet at this point.
> + /* Enable charge rationing by default */
> + ret = regmap_update_bits(info->regmap, UCS1002_REG_GENERAL_CFG,
> + F_RATION_EN, F_RATION_EN);
> + if (ret)
> + return ret;
Another silent error ? Seems odd, especially since we just above
already claimed that the device was registered.
> +
> + dev_dbg(dev, "set active mode selection through i2c\n");
> + /*
> + * Ignore the M1, M2, PWR_EN, and EM_EN pin states. Set active
> + * mode selection to Dedicated Charger Emulation Cycle.
> + *
> + * #M1 #M2 EM_EN
> + * 0 0 1 - Dedicated Charger Emulation Cycle
> + *
> + */
> + ret = regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> + F_PIN_IGNORE | F_EM_EN_SET | F_M2_SET |
> + F_M1_SET, F_PIN_IGNORE | F_EM_EN_SET);
> + if (ret)
> + return ret;
And another one.
> + /*
> + * Be safe and set initial current limit to 500mA
> + */
> + ret = ucs1002_set_max_current(info, 500000);
> + if (ret) {
> + dev_err(dev, "Failed to read max current default\n");
read ?
> + return ret;
> + }
> +
> + info->charger = devm_power_supply_register(dev, &ucs1002_charger_desc,
> + &charger_config);
> + if (IS_ERR(info->charger)) {
> + dev_err(dev, "failed to register power supply\n");
> + return PTR_ERR(info->charger);
> + }
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®val);
> + if (ret)
> + return ret;
> +
> + info->regulator_descriptor =
> + devm_kmemdup(dev, &ucs1002_regulator_descriptor,
> + sizeof(ucs1002_regulator_descriptor),
> + GFP_KERNEL);
What if devm_kmemdup() returns NULL ?
> + info->regulator_descriptor->enable_is_inverted = !(regval & F_SEL_PIN);
> +
> + regulator_config.dev = dev;
> + regulator_config.of_node = dev->of_node;
> + regulator_config.regmap = info->regmap;
> +
> + rdev = devm_regulator_register(dev, info->regulator_descriptor,
> + ®ulator_config);
> + if (IS_ERR(rdev)) {
> + dev_err(dev, "failed to register VBUS regulator\n");
> + return PTR_ERR(rdev);
> + }
> +
> + if (irq_a_det > 0) {
> + ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
> + ucs1002_charger_irq,
> + IRQF_TRIGGER_FALLING |
> + IRQF_TRIGGER_RISING |
> + IRQF_ONESHOT,
> + "ucs1002-a_det", info);
> + if (ret) {
> + dev_err(dev, "failed to request A_DET threaded irq\n");
> + return ret;
> + }
> + }
> +
> + if (irq_alert > 0) {
> + ret = devm_request_threaded_irq(dev, irq_alert, NULL,
> + ucs1002_alert_irq,
> + IRQF_TRIGGER_FALLING |
> + IRQF_TRIGGER_RISING |
> + IRQF_ONESHOT,
> + "ucs1002-alert", info);
> + if (ret) {
> + dev_err(dev, "failed to request ALERT threaded irq\n");
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +#if IS_ENABLED(CONFIG_OF)
> +static const struct of_device_id ucs1002_of_match[] = {
> + { .compatible = "microchip,ucs1002", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, ucs1002_of_match);
> +#endif
> +
> +static const struct i2c_device_id ucs1002_ids[] = {
> + {"ucs1002", 0},
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(i2c, ucs1002_ids);
> +
> +static struct i2c_driver ucs1002_driver = {
> + .driver = {
> + .name = "ucs1002",
> + .of_match_table = of_match_ptr(ucs1002_of_match),
> + },
> + .probe = ucs1002_probe,
> +};
> +module_i2c_driver(ucs1002_driver);
> +
> +MODULE_DESCRIPTION("Microchip UCS1002 Programmable USB Port Power Controller");
> +MODULE_AUTHOR("Enric Balletbo Serra <enric.balletbo@collabora.com>");
> +MODULE_AUTHOR("Andrey Smirnov <andrew.smirnov@gmail.com>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
2019-04-17 8:44 ` [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant Andrey Smirnov
@ 2019-04-26 16:12 ` Guenter Roeck
0 siblings, 0 replies; 13+ messages in thread
From: Guenter Roeck @ 2019-04-26 16:12 UTC (permalink / raw)
To: Andrey Smirnov
Cc: linux-pm, Chris Health, Lucas Stach, Fabio Estevam,
Sebastian Reichel, linux-kernel
On Wed, Apr 17, 2019 at 01:44:55AM -0700, Andrey Smirnov wrote:
> Add POWER_SUPPLY_HEALTH_OVERCURRENT constant in order to allow
> singalling overcurrent condition via power supply health information.
>
> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> Cc: Chris Health <cphealy@gmail.com>
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Guenter Roeck <linux@roeck-us.net>
> Cc: Sebastian Reichel <sre@kernel.org>
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-pm@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> drivers/power/supply/power_supply_sysfs.c | 2 +-
> include/linux/power_supply.h | 1 +
> 2 files changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/power/supply/power_supply_sysfs.c b/drivers/power/supply/power_supply_sysfs.c
> index 5e91946731fd..464f4e837601 100644
> --- a/drivers/power/supply/power_supply_sysfs.c
> +++ b/drivers/power/supply/power_supply_sysfs.c
> @@ -62,7 +62,7 @@ static const char * const power_supply_charge_type_text[] = {
> static const char * const power_supply_health_text[] = {
> "Unknown", "Good", "Overheat", "Dead", "Over voltage",
> "Unspecified failure", "Cold", "Watchdog timer expire",
> - "Safety timer expire"
> + "Safety timer expire", "Over current"
> };
>
> static const char * const power_supply_technology_text[] = {
> diff --git a/include/linux/power_supply.h b/include/linux/power_supply.h
> index 2f9c201a54d1..bdab14c7ca4d 100644
> --- a/include/linux/power_supply.h
> +++ b/include/linux/power_supply.h
> @@ -57,6 +57,7 @@ enum {
> POWER_SUPPLY_HEALTH_COLD,
> POWER_SUPPLY_HEALTH_WATCHDOG_TIMER_EXPIRE,
> POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE,
> + POWER_SUPPLY_HEALTH_OVERCURRENT,
> };
>
> enum {
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-17 8:44 ` [PATCH 2/3] power: supply: Add driver for Microchip UCS1002 Andrey Smirnov
2019-04-26 14:43 ` Lucas Stach
2019-04-26 16:10 ` Guenter Roeck
@ 2019-04-26 16:51 ` Enric Balletbo Serra
2019-04-26 17:04 ` Guenter Roeck
2019-04-27 0:29 ` Andrey Smirnov
2 siblings, 2 replies; 13+ messages in thread
From: Enric Balletbo Serra @ 2019-04-26 16:51 UTC (permalink / raw)
To: Andrey Smirnov
Cc: Linux PM list, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Sebastian Reichel, linux-kernel
Hi Andrey,
Many thanks to push this upstream. Actually this the fifth version [1]
of this patchset. I think that is interesting for the maintainers
maintain the history and the changelog.
[1] https://lkml.org/lkml/2016/3/14/233
Missatge de Andrey Smirnov <andrew.smirnov@gmail.com> del dia dc., 17
d’abr. 2019 a les 10:46:
>
> Add driver for Microchip UCS1002 Programmable USB Port Power
> Controller with Charger Emulation. The driver exposed a power supply
> device to control/monitor various parameter of the device as well as a
> regulator to allow controlling VBUS line.
>
> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> Cc: Chris Health <cphealy@gmail.com>
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Guenter Roeck <linux@roeck-us.net>
> Cc: Sebastian Reichel <sre@kernel.org>
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-pm@vger.kernel.org
> ---
> drivers/power/supply/Kconfig | 9 +
> drivers/power/supply/Makefile | 1 +
> drivers/power/supply/ucs1002_power.c | 639 +++++++++++++++++++++++++++
> 3 files changed, 649 insertions(+)
> create mode 100644 drivers/power/supply/ucs1002_power.c
>
> diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
> index e901b9879e7e..c614c8a196f3 100644
> --- a/drivers/power/supply/Kconfig
> +++ b/drivers/power/supply/Kconfig
> @@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
> Say Y here to enable support for fuel gauge with SC27XX
> PMIC chips.
>
> +config CHARGER_UCS1002
> + tristate "Microchip UCS1002 USB Port Power Controller"
> + depends on I2C
> + depends on OF
> + select REGMAP_I2C
> + help
> + Say Y to enable support for Microchip UCS1002 Programmable
> + USB Port Power Controller with Charger Emulation.
> +
> endif # POWER_SUPPLY
> diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
> index b731c2a9b695..c56803a9e4fe 100644
> --- a/drivers/power/supply/Makefile
> +++ b/drivers/power/supply/Makefile
> @@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
> obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
> obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
> obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
> +obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
> diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c
> new file mode 100644
> index 000000000000..b0b81d62e003
> --- /dev/null
> +++ b/drivers/power/supply/ucs1002_power.c
> @@ -0,0 +1,639 @@
> +// SPDX-License-Identifier: GPL-2.0+
There is a license mismatch, or this should be GPL-2.0 or
MODULE_LICENCE should GPL.
> +/*
> + * Driver for UCS1002 Programmable USB Port Power Controller
> + *
> + * Copyright (C) 2019 Zodiac Inflight Innovations
> + */
> +#include <linux/freezer.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/kthread.h>
> +#include <linux/device.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/power_supply.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/of_regulator.h>
> +
> +/* UCS1002 Registers */
> +#define UCS1002_REG_CURRENT_MEASUREMENT 0x00
> +
> +/*
> + * The Total Accumulated Charge registers store the total accumulated
> + * charge delivered from the VS source to a portable device. The total
> + * value is calculated using four registers, from 01h to 04h. The bit
> + * weighting of the registers is given in mA/hrs.
> + */
> +#define UCS1002_REG_TOTAL_ACC_CHARGE 0x01
> +
> +/* Other Status Register */
> +#define UCS1002_REG_OTHER_STATUS 0x0f
> +# define F_ADET_PIN BIT(4)
> +# define F_CHG_ACT BIT(3)
> +
> +/* Interrupt Status */
> +#define UCS1002_REG_INTERRUPT_STATUS 0x10
> +# define F_DISCHARGE_ERR BIT(6)
> +# define F_RESET BIT(5)
> +# define F_MIN_KEEP_OUT BIT(4)
> +# define F_TSD BIT(3)
> +# define F_OVER_VOLT BIT(2)
> +# define F_BACK_VOLT BIT(1)
> +# define F_OVER_ILIM BIT(0)
> +
> +/* Pin Status Register */
> +#define UCS1002_REG_PIN_STATUS 0x14
> +# define UCS1002_PWR_STATE_MASK 0x03
> +# define F_PWR_EN_PIN BIT(6)
> +# define F_M2_PIN BIT(5)
> +# define F_M1_PIN BIT(4)
> +# define F_EM_EN_PIN BIT(3)
> +# define F_SEL_PIN BIT(2)
> +# define F_ACTIVE_MODE_MASK GENMASK(5, 3)
> +# define F_ACTIVE_MODE_PASSTHROUGH F_M2_PIN
> +# define F_ACTIVE_MODE_DEDICATED F_EM_EN_PIN
> +# define F_ACTIVE_MODE_BC12_DCP (F_M2_PIN | F_EM_EN_PIN)
> +# define F_ACTIVE_MODE_BC12_SDP F_M1_PIN
> +# define F_ACTIVE_MODE_BC12_CDP (F_M1_PIN | F_M2_PIN | F_EM_EN_PIN)
> +
> +/* General Configuration Register */
> +#define UCS1002_REG_GENERAL_CFG 0x15
> +# define F_RATION_EN BIT(3)
> +
> +/* Emulation Configuration Register */
> +#define UCS1002_REG_EMU_CFG 0x16
> +
> +/* Switch Configuration Register */
> +#define UCS1002_REG_SWITCH_CFG 0x17
> +# define F_PIN_IGNORE BIT(7)
> +# define F_EM_EN_SET BIT(5)
> +# define F_M2_SET BIT(4)
> +# define F_M1_SET BIT(3)
> +# define F_S0_SET BIT(2)
> +# define F_PWR_EN_SET BIT(1)
> +# define F_LATCH_SET BIT(0)
> +# define V_SET_ACTIVE_MODE_MASK GENMASK(5, 3)
> +# define V_SET_ACTIVE_MODE_PASSTHROUGH F_M2_SET
> +# define V_SET_ACTIVE_MODE_DEDICATED F_EM_EN_SET
> +# define V_SET_ACTIVE_MODE_BC12_DCP (F_M2_SET | F_EM_EN_SET)
> +# define V_SET_ACTIVE_MODE_BC12_SDP F_M1_SET
> +# define V_SET_ACTIVE_MODE_BC12_CDP (F_M1_SET | F_M2_SET | F_EM_EN_SET)
> +
> +/* Current Limit Register */
> +#define UCS1002_REG_ILIMIT 0x19
> +# define UCS1002_ILIM_SW_MASK GENMASK(3, 0)
> +
> +/* Product ID */
> +#define UCS1002_REG_PRODUCT_ID 0xfd
> +# define UCS1002_PRODUCT_ID 0x4e
> +
> +/* Manufacture name */
> +#define UCS1002_MANUFACTURER "SMSC"
> +
> +struct ucs1002_info {
> + struct power_supply *charger;
> + struct i2c_client *client;
> + struct regmap *regmap;
> + struct regulator_desc *regulator_descriptor;
> + bool present;
> +};
> +
> +static enum power_supply_property ucs1002_props[] = {
> + POWER_SUPPLY_PROP_ONLINE,
> + POWER_SUPPLY_PROP_CHARGE_NOW,
> + POWER_SUPPLY_PROP_CURRENT_NOW,
> + POWER_SUPPLY_PROP_CURRENT_MAX,
> + POWER_SUPPLY_PROP_PRESENT, /* the presence of PED */
> + POWER_SUPPLY_PROP_MANUFACTURER,
> + POWER_SUPPLY_PROP_USB_TYPE,
> + POWER_SUPPLY_PROP_HEALTH,
> +};
> +
> +static int ucs1002_get_online(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®);
> + if (ret)
> + return ret;
> +
> + val->intval = !!(reg & F_CHG_ACT);
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_charge(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + /*
> + * To fit within 32 bits some values are rounded (uA/h)
> + *
> + * For Total Accumulated Charge Middle Low Byte register, addr
> + * 03h, byte 2
> + *
> + * B0: 0.01084 mA/h rounded to 11 uA/h
> + * B1: 0.02169 mA/h rounded to 22 uA/h
> + * B2: 0.04340 mA/h rounded to 43 uA/h
> + * B3: 0.08676 mA/h rounded to 87 uA/h
> + * B4: 0.17350 mA/h rounded to 173 uÁ/h
> + *
> + * For Total Accumulated Charge Low Byte register, addr 04h,
> + * byte 3
> + *
> + * B6: 0.00271 mA/h rounded to 3 uA/h
> + * B7: 0.005422 mA/h rounded to 5 uA/h
> + */
> + static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
> + 0, 0, 0, 0, 0, 0, 3, 5,
> +
nit: I personally don't like these empty lines here.
> + 11, 22, 43, 87, 173, 347, 694, 1388,
> +
> + 2776, 5552, 11105, 22210, 44420, 88840, 177700, 355400,
> +
> + 710700, 1421000, 2843000, 5685000, 11371000, 22742000,
> + 45484000, 90968000,
> + };
> + unsigned long total_acc_charger;
> + unsigned int reg;
> + int i, ret;
> +
> + ret = regmap_bulk_read(info->regmap, UCS1002_REG_TOTAL_ACC_CHARGE,
> + ®, sizeof(u32));
> + if (ret)
> + return ret;
> +
> + total_acc_charger = be32_to_cpu(reg);
> + val->intval = 0;
> +
> + for_each_set_bit(i, &total_acc_charger, ARRAY_SIZE(bit_weights_uAh))
> + val->intval += bit_weights_uAh[i];
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_current(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + /*
> + * The Current Measurement register stores the measured
> + * current value delivered to the portable device. The range
> + * is from 9.76 mA to 2.5 A.
> + */
> + static const int bit_weights_uA[BITS_PER_TYPE(u8)] = {
> + 9760, 19500, 39000, 78100, 156200, 312300, 624600, 1249300,
> + };
> + unsigned long current_measurement;
> + unsigned int reg;
> + int i, ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_CURRENT_MEASUREMENT, ®);
> + if (ret)
> + return ret;
> +
> + current_measurement = reg;
> + val->intval = 0;
> +
> + for_each_set_bit(i, ¤t_measurement, ARRAY_SIZE(bit_weights_uA))
> + val->intval += bit_weights_uA[i];
> +
> + return 0;
> +}
> +
> +/*
> + * The Current Limit register stores the maximum current used by the
> + * port switch. The range is from 500mA to 2.5 A.
> + */
> +static const u32 ucs1002_current_limit_uA[] = {
> + 500000, 900000, 1000000, 1200000, 1500000, 1800000, 2000000, 2500000,
> +};
> +
> +static int ucs1002_get_max_current(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> + if (ret)
> + return ret;
> +
> + val->intval = ucs1002_current_limit_uA[reg & UCS1002_ILIM_SW_MASK];
> +
> + return 0;
> +}
> +
> +static int ucs1002_set_max_current(struct ucs1002_info *info, u32 val)
> +{
> + unsigned int reg;
> + int ret, idx;
> +
> + for (idx = 0; idx < ARRAY_SIZE(ucs1002_current_limit_uA); idx++) {
> + if (val == ucs1002_current_limit_uA[idx])
> + break;
> + }
> +
> + if (idx == ARRAY_SIZE(ucs1002_current_limit_uA)) {
> + dev_err(&info->client->dev,
> + "%d is an invalid max current value\n", val);
> + return -EINVAL;
> + }
> +
> + ret = regmap_write(info->regmap, UCS1002_REG_ILIMIT, idx);
> + if (ret)
> + return ret;
> + /*
> + * Any current limit setting exceeding the one set via ILIM
> + * pin will be rejected, so we read out freshly changed limit
> + * to make sure that it took effect.
> + */
> + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> + if (ret)
> + return ret;
> +
> + if (reg != idx)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static enum power_supply_usb_type ucs1002_usb_types[] = {
> + POWER_SUPPLY_USB_TYPE_PD,
> + POWER_SUPPLY_USB_TYPE_SDP,
> + POWER_SUPPLY_USB_TYPE_DCP,
> + POWER_SUPPLY_USB_TYPE_CDP,
> + POWER_SUPPLY_USB_TYPE_UNKNOWN,
> +};
> +
> +static int ucs1002_set_usb_type(struct ucs1002_info *info, int val)
> +{
> + unsigned int mode;
> +
> + if (val >= ARRAY_SIZE(ucs1002_usb_types))
> + return -EINVAL;
> +
> + switch (ucs1002_usb_types[val]) {
> + case POWER_SUPPLY_USB_TYPE_PD:
> + mode = V_SET_ACTIVE_MODE_DEDICATED;
> + break;
> + case POWER_SUPPLY_USB_TYPE_SDP:
> + mode = V_SET_ACTIVE_MODE_BC12_SDP;
> + break;
> + case POWER_SUPPLY_USB_TYPE_DCP:
> + mode = V_SET_ACTIVE_MODE_BC12_DCP;
> + break;
> + case POWER_SUPPLY_USB_TYPE_CDP:
> + mode = V_SET_ACTIVE_MODE_BC12_CDP;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> + V_SET_ACTIVE_MODE_MASK, mode);
> +}
> +
> +static int ucs1002_get_usb_type(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + enum power_supply_usb_type type;
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®);
> + if (ret)
> + return ret;
> +
> + switch (reg & F_ACTIVE_MODE_MASK) {
> + default:
> + type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
> + break;
> + case F_ACTIVE_MODE_DEDICATED:
> + type = POWER_SUPPLY_USB_TYPE_PD;
> + break;
> + case F_ACTIVE_MODE_BC12_SDP:
> + type = POWER_SUPPLY_USB_TYPE_SDP;
> + break;
> + case F_ACTIVE_MODE_BC12_DCP:
> + type = POWER_SUPPLY_USB_TYPE_DCP;
> + break;
> + case F_ACTIVE_MODE_BC12_CDP:
> + type = POWER_SUPPLY_USB_TYPE_CDP;
> + break;
> + };
> +
> + val->intval = type;
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_health(struct ucs1002_info *info,
> + union power_supply_propval *val)
> +{
> + unsigned int reg;
> + int ret, health;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_INTERRUPT_STATUS, ®);
> + if (ret)
> + return ret;
> +
> + if (reg & F_TSD)
> + health = POWER_SUPPLY_HEALTH_OVERHEAT;
> + else if (reg & (F_OVER_VOLT | F_BACK_VOLT))
> + health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> + else if (reg & F_OVER_ILIM)
> + health = POWER_SUPPLY_HEALTH_OVERCURRENT;
> + else if (reg & (F_DISCHARGE_ERR | F_MIN_KEEP_OUT))
> + health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> + else
> + health = POWER_SUPPLY_HEALTH_GOOD;
> +
> + val->intval = health;
> +
> + return 0;
> +}
> +
> +static int ucs1002_get_property(struct power_supply *psy,
> + enum power_supply_property psp,
> + union power_supply_propval *val)
> +{
> + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_ONLINE:
> + return ucs1002_get_online(info, val);
> + case POWER_SUPPLY_PROP_CHARGE_NOW:
> + return ucs1002_get_charge(info, val);
> + case POWER_SUPPLY_PROP_CURRENT_NOW:
> + return ucs1002_get_current(info, val);
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + return ucs1002_get_max_current(info, val);
> + case POWER_SUPPLY_PROP_USB_TYPE:
> + return ucs1002_get_usb_type(info, val);
> + case POWER_SUPPLY_PROP_HEALTH:
> + return ucs1002_get_health(info, val);
> + case POWER_SUPPLY_PROP_PRESENT:
> + val->intval = info->present;
> + return 0;
> + case POWER_SUPPLY_PROP_MANUFACTURER:
> + val->strval = UCS1002_MANUFACTURER;
> + return 0;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int ucs1002_set_property(struct power_supply *psy,
> + enum power_supply_property psp,
> + const union power_supply_propval *val)
> +{
> + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + return ucs1002_set_max_current(info, val->intval);
> + case POWER_SUPPLY_PROP_USB_TYPE:
> + return ucs1002_set_usb_type(info, val->intval);
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int ucs1002_property_is_writeable(struct power_supply *psy,
> + enum power_supply_property psp)
> +{
> + switch (psp) {
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + case POWER_SUPPLY_PROP_USB_TYPE:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static const struct power_supply_desc ucs1002_charger_desc = {
> + .name = "ucs1002",
> + .type = POWER_SUPPLY_TYPE_USB,
> + .usb_types = ucs1002_usb_types,
> + .num_usb_types = ARRAY_SIZE(ucs1002_usb_types),
> + .get_property = ucs1002_get_property,
> + .set_property = ucs1002_set_property,
> + .property_is_writeable = ucs1002_property_is_writeable,
> + .properties = ucs1002_props,
> + .num_properties = ARRAY_SIZE(ucs1002_props),
> +};
> +
> +static irqreturn_t ucs1002_charger_irq(int irq, void *data)
> +{
> + int ret, regval;
> + bool present;
> + struct ucs1002_info *info = data;
> +
> + present = info->present;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®val);
> + if (ret)
> + return IRQ_HANDLED;
> +
> + /* update attached status */
> + info->present = (regval & F_ADET_PIN) ? true : false;
> +
> + /* notify the change */
> + if (present != info->present)
> + power_supply_changed(info->charger);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t ucs1002_alert_irq(int irq, void *data)
> +{
> + struct ucs1002_info *info = data;
> +
> + power_supply_changed(info->charger);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static const struct regulator_ops ucs1002_regulator_ops = {
> + .is_enabled = regulator_is_enabled_regmap,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> +};
> +
> +static const struct regulator_desc ucs1002_regulator_descriptor = {
> + .name = "ucs1002-vbus",
> + .ops = &ucs1002_regulator_ops,
> + .type = REGULATOR_VOLTAGE,
> + .owner = THIS_MODULE,
> + .enable_reg = UCS1002_REG_SWITCH_CFG,
> + .enable_mask = F_PWR_EN_SET,
> + .enable_val = F_PWR_EN_SET,
> + .fixed_uV = 5000000,
> + .n_voltages = 1,
> +};
> +
> +static int ucs1002_probe(struct i2c_client *client,
> + const struct i2c_device_id *dev_id)
> +{
> + struct device *dev = &client->dev;
> + struct power_supply_config charger_config = {};
> + const struct regmap_config regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + };
> + struct regulator_config regulator_config = {};
> + int irq_a_det, irq_alert, ret;
> + struct regulator_dev *rdev;
> + struct ucs1002_info *info;
> + unsigned int regval;
> +
> + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> + if (!info)
> + return -ENOMEM;
> +
> + info->regmap = devm_regmap_init_i2c(client, ®map_config);
> + if (IS_ERR(info->regmap)) {
> + ret = PTR_ERR(info->regmap);
> + dev_err(dev, "regmap initialization failed: %d\n", ret);
> + return ret;
> + }
> +
> + info->client = client;
> +
> + irq_a_det = of_irq_get_byname(dev->of_node, "a_det");
> + irq_alert = of_irq_get_byname(dev->of_node, "alert");
> +
> + charger_config.of_node = dev->of_node;
> + charger_config.drv_data = info;
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_PRODUCT_ID, ®val);
> + if (ret)
> + return ret;
> +
> + if (regval != UCS1002_PRODUCT_ID) {
> + dev_err(dev,
> + "Product ID does not match (0x%02x != 0x%02x)\n",
> + regval, UCS1002_PRODUCT_ID);
> + return -ENODEV;
> + }
> +
> + dev_info(dev, "registered with product id 0x%02x\n", regval);
> +
> + /* Enable charge rationing by default */
> + ret = regmap_update_bits(info->regmap, UCS1002_REG_GENERAL_CFG,
> + F_RATION_EN, F_RATION_EN);
> + if (ret)
> + return ret;
> +
> + dev_dbg(dev, "set active mode selection through i2c\n");
> + /*
> + * Ignore the M1, M2, PWR_EN, and EM_EN pin states. Set active
> + * mode selection to Dedicated Charger Emulation Cycle.
> + *
> + * #M1 #M2 EM_EN
> + * 0 0 1 - Dedicated Charger Emulation Cycle
> + *
> + */
> + ret = regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> + F_PIN_IGNORE | F_EM_EN_SET | F_M2_SET |
> + F_M1_SET, F_PIN_IGNORE | F_EM_EN_SET);
> + if (ret)
> + return ret;
> + /*
> + * Be safe and set initial current limit to 500mA
> + */
> + ret = ucs1002_set_max_current(info, 500000);
> + if (ret) {
> + dev_err(dev, "Failed to read max current default\n");
> + return ret;
> + }
> +
> + info->charger = devm_power_supply_register(dev, &ucs1002_charger_desc,
> + &charger_config);
> + if (IS_ERR(info->charger)) {
> + dev_err(dev, "failed to register power supply\n");
> + return PTR_ERR(info->charger);
> + }
> +
> + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®val);
> + if (ret)
> + return ret;
> +
> + info->regulator_descriptor =
> + devm_kmemdup(dev, &ucs1002_regulator_descriptor,
> + sizeof(ucs1002_regulator_descriptor),
> + GFP_KERNEL);
> + info->regulator_descriptor->enable_is_inverted = !(regval & F_SEL_PIN);
> +
> + regulator_config.dev = dev;
> + regulator_config.of_node = dev->of_node;
> + regulator_config.regmap = info->regmap;
> +
> + rdev = devm_regulator_register(dev, info->regulator_descriptor,
> + ®ulator_config);
> + if (IS_ERR(rdev)) {
> + dev_err(dev, "failed to register VBUS regulator\n");
> + return PTR_ERR(rdev);
> + }
> +
> + if (irq_a_det > 0) {
> + ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
> + ucs1002_charger_irq,
> + IRQF_TRIGGER_FALLING |
> + IRQF_TRIGGER_RISING |
> + IRQF_ONESHOT,
> + "ucs1002-a_det", info);
> + if (ret) {
> + dev_err(dev, "failed to request A_DET threaded irq\n");
> + return ret;
> + }
> + }
> +
> + if (irq_alert > 0) {
> + ret = devm_request_threaded_irq(dev, irq_alert, NULL,
> + ucs1002_alert_irq,
> + IRQF_TRIGGER_FALLING |
> + IRQF_TRIGGER_RISING |
> + IRQF_ONESHOT,
> + "ucs1002-alert", info);
> + if (ret) {
> + dev_err(dev, "failed to request ALERT threaded irq\n");
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +#if IS_ENABLED(CONFIG_OF)
This driver is DT only, this if is not needed.
> +static const struct of_device_id ucs1002_of_match[] = {
> + { .compatible = "microchip,ucs1002", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, ucs1002_of_match);
> +#endif
> +
> +static const struct i2c_device_id ucs1002_ids[] = {
> + {"ucs1002", 0},
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(i2c, ucs1002_ids);
> +
> +static struct i2c_driver ucs1002_driver = {
> + .driver = {
> + .name = "ucs1002",
> + .of_match_table = of_match_ptr(ucs1002_of_match),
No need to use of_match_ptr, is DT-only.
> + },
> + .probe = ucs1002_probe,
> +};
> +module_i2c_driver(ucs1002_driver);
> +
> +MODULE_DESCRIPTION("Microchip UCS1002 Programmable USB Port Power Controller");
> +MODULE_AUTHOR("Enric Balletbo Serra <enric.balletbo@collabora.com>");
I'm not sure how much differs this patch from the one I sent 3 years
ago ... but if i'm the author or co-author you should add the
signed-off-by.
[1] https://lkml.org/lkml/2016/3/14/233
[2] https://www.spinics.net/lists/devicetree/msg122745.html
> +MODULE_AUTHOR("Andrey Smirnov <andrew.smirnov@gmail.com>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-26 16:51 ` Enric Balletbo Serra
@ 2019-04-26 17:04 ` Guenter Roeck
2019-04-27 0:29 ` Andrey Smirnov
1 sibling, 0 replies; 13+ messages in thread
From: Guenter Roeck @ 2019-04-26 17:04 UTC (permalink / raw)
To: Enric Balletbo Serra
Cc: Andrey Smirnov, Linux PM list, Chris Health, Lucas Stach,
Fabio Estevam, Sebastian Reichel, linux-kernel
On Fri, Apr 26, 2019 at 06:51:51PM +0200, Enric Balletbo Serra wrote:
> Hi Andrey,
>
> Many thanks to push this upstream. Actually this the fifth version [1]
> of this patchset. I think that is interesting for the maintainers
> maintain the history and the changelog.
>
> [1] https://lkml.org/lkml/2016/3/14/233
>
> Missatge de Andrey Smirnov <andrew.smirnov@gmail.com> del dia dc., 17
> d’abr. 2019 a les 10:46:
> >
> > Add driver for Microchip UCS1002 Programmable USB Port Power
> > Controller with Charger Emulation. The driver exposed a power supply
> > device to control/monitor various parameter of the device as well as a
> > regulator to allow controlling VBUS line.
> >
> > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> > Cc: Chris Health <cphealy@gmail.com>
> > Cc: Lucas Stach <l.stach@pengutronix.de>
> > Cc: Fabio Estevam <fabio.estevam@nxp.com>
> > Cc: Guenter Roeck <linux@roeck-us.net>
> > Cc: Sebastian Reichel <sre@kernel.org>
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-pm@vger.kernel.org
> > ---
...
> > + static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
> > + 0, 0, 0, 0, 0, 0, 3, 5,
> > +
>
> nit: I personally don't like these empty lines here.
>
I stumbled over those as well, but then I realized that they
split up the 32 bit into bytes, so it does make some sense.
Guenter
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-26 16:10 ` Guenter Roeck
@ 2019-04-27 0:16 ` Andrey Smirnov
0 siblings, 0 replies; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-27 0:16 UTC (permalink / raw)
To: Guenter Roeck
Cc: linux-pm, Chris Health, Lucas Stach, Fabio Estevam,
Sebastian Reichel, linux-kernel
On Fri, Apr 26, 2019 at 9:10 AM Guenter Roeck <linux@roeck-us.net> wrote:
>
> On Wed, Apr 17, 2019 at 01:44:56AM -0700, Andrey Smirnov wrote:
> > Add driver for Microchip UCS1002 Programmable USB Port Power
> > Controller with Charger Emulation. The driver exposed a power supply
> > device to control/monitor various parameter of the device as well as a
> > regulator to allow controlling VBUS line.
> >
> > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> > Cc: Chris Health <cphealy@gmail.com>
> > Cc: Lucas Stach <l.stach@pengutronix.de>
> > Cc: Fabio Estevam <fabio.estevam@nxp.com>
> > Cc: Guenter Roeck <linux@roeck-us.net>
> > Cc: Sebastian Reichel <sre@kernel.org>
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-pm@vger.kernel.org
> > ---
> > drivers/power/supply/Kconfig | 9 +
> > drivers/power/supply/Makefile | 1 +
> > drivers/power/supply/ucs1002_power.c | 639 +++++++++++++++++++++++++++
> > 3 files changed, 649 insertions(+)
> > create mode 100644 drivers/power/supply/ucs1002_power.c
> >
> > diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
> > index e901b9879e7e..c614c8a196f3 100644
> > --- a/drivers/power/supply/Kconfig
> > +++ b/drivers/power/supply/Kconfig
> > @@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
> > Say Y here to enable support for fuel gauge with SC27XX
> > PMIC chips.
> >
> > +config CHARGER_UCS1002
> > + tristate "Microchip UCS1002 USB Port Power Controller"
> > + depends on I2C
> > + depends on OF
> > + select REGMAP_I2C
> > + help
> > + Say Y to enable support for Microchip UCS1002 Programmable
> > + USB Port Power Controller with Charger Emulation.
> > +
> > endif # POWER_SUPPLY
> > diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
> > index b731c2a9b695..c56803a9e4fe 100644
> > --- a/drivers/power/supply/Makefile
> > +++ b/drivers/power/supply/Makefile
> > @@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
> > obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
> > obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
> > obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
> > +obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
> > diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c
> > new file mode 100644
> > index 000000000000..b0b81d62e003
> > --- /dev/null
> > +++ b/drivers/power/supply/ucs1002_power.c
> > @@ -0,0 +1,639 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Driver for UCS1002 Programmable USB Port Power Controller
> > + *
> > + * Copyright (C) 2019 Zodiac Inflight Innovations
> > + */
> > +#include <linux/freezer.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/i2c.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/kthread.h>
> > +#include <linux/device.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/power_supply.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/driver.h>
> > +#include <linux/regulator/of_regulator.h>
> > +
> You probably want to include linux/bits.h as well.
Sure, will do in v2.
>
> > +/* UCS1002 Registers */
> > +#define UCS1002_REG_CURRENT_MEASUREMENT 0x00
> > +
> > +/*
> > + * The Total Accumulated Charge registers store the total accumulated
> > + * charge delivered from the VS source to a portable device. The total
> > + * value is calculated using four registers, from 01h to 04h. The bit
> > + * weighting of the registers is given in mA/hrs.
> > + */
> > +#define UCS1002_REG_TOTAL_ACC_CHARGE 0x01
> > +
> > +/* Other Status Register */
> > +#define UCS1002_REG_OTHER_STATUS 0x0f
> > +# define F_ADET_PIN BIT(4)
> > +# define F_CHG_ACT BIT(3)
> > +
> > +/* Interrupt Status */
> > +#define UCS1002_REG_INTERRUPT_STATUS 0x10
> > +# define F_DISCHARGE_ERR BIT(6)
> > +# define F_RESET BIT(5)
> > +# define F_MIN_KEEP_OUT BIT(4)
> > +# define F_TSD BIT(3)
> > +# define F_OVER_VOLT BIT(2)
> > +# define F_BACK_VOLT BIT(1)
> > +# define F_OVER_ILIM BIT(0)
> > +
> > +/* Pin Status Register */
> > +#define UCS1002_REG_PIN_STATUS 0x14
> > +# define UCS1002_PWR_STATE_MASK 0x03
> > +# define F_PWR_EN_PIN BIT(6)
> > +# define F_M2_PIN BIT(5)
> > +# define F_M1_PIN BIT(4)
> > +# define F_EM_EN_PIN BIT(3)
> > +# define F_SEL_PIN BIT(2)
> > +# define F_ACTIVE_MODE_MASK GENMASK(5, 3)
> > +# define F_ACTIVE_MODE_PASSTHROUGH F_M2_PIN
> > +# define F_ACTIVE_MODE_DEDICATED F_EM_EN_PIN
> > +# define F_ACTIVE_MODE_BC12_DCP (F_M2_PIN | F_EM_EN_PIN)
> > +# define F_ACTIVE_MODE_BC12_SDP F_M1_PIN
> > +# define F_ACTIVE_MODE_BC12_CDP (F_M1_PIN | F_M2_PIN | F_EM_EN_PIN)
> > +
> > +/* General Configuration Register */
> > +#define UCS1002_REG_GENERAL_CFG 0x15
> > +# define F_RATION_EN BIT(3)
> > +
> > +/* Emulation Configuration Register */
> > +#define UCS1002_REG_EMU_CFG 0x16
> > +
> > +/* Switch Configuration Register */
> > +#define UCS1002_REG_SWITCH_CFG 0x17
> > +# define F_PIN_IGNORE BIT(7)
> > +# define F_EM_EN_SET BIT(5)
> > +# define F_M2_SET BIT(4)
> > +# define F_M1_SET BIT(3)
> > +# define F_S0_SET BIT(2)
> > +# define F_PWR_EN_SET BIT(1)
> > +# define F_LATCH_SET BIT(0)
> > +# define V_SET_ACTIVE_MODE_MASK GENMASK(5, 3)
> > +# define V_SET_ACTIVE_MODE_PASSTHROUGH F_M2_SET
> > +# define V_SET_ACTIVE_MODE_DEDICATED F_EM_EN_SET
> > +# define V_SET_ACTIVE_MODE_BC12_DCP (F_M2_SET | F_EM_EN_SET)
> > +# define V_SET_ACTIVE_MODE_BC12_SDP F_M1_SET
> > +# define V_SET_ACTIVE_MODE_BC12_CDP (F_M1_SET | F_M2_SET | F_EM_EN_SET)
> > +
> > +/* Current Limit Register */
> > +#define UCS1002_REG_ILIMIT 0x19
> > +# define UCS1002_ILIM_SW_MASK GENMASK(3, 0)
> > +
> > +/* Product ID */
> > +#define UCS1002_REG_PRODUCT_ID 0xfd
> > +# define UCS1002_PRODUCT_ID 0x4e
> > +
> > +/* Manufacture name */
> > +#define UCS1002_MANUFACTURER "SMSC"
> > +
> > +struct ucs1002_info {
> > + struct power_supply *charger;
> > + struct i2c_client *client;
> > + struct regmap *regmap;
> > + struct regulator_desc *regulator_descriptor;
> > + bool present;
> > +};
> > +
> > +static enum power_supply_property ucs1002_props[] = {
> > + POWER_SUPPLY_PROP_ONLINE,
> > + POWER_SUPPLY_PROP_CHARGE_NOW,
> > + POWER_SUPPLY_PROP_CURRENT_NOW,
> > + POWER_SUPPLY_PROP_CURRENT_MAX,
> > + POWER_SUPPLY_PROP_PRESENT, /* the presence of PED */
> > + POWER_SUPPLY_PROP_MANUFACTURER,
> > + POWER_SUPPLY_PROP_USB_TYPE,
> > + POWER_SUPPLY_PROP_HEALTH,
> > +};
> > +
> > +static int ucs1002_get_online(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®);
> > + if (ret)
> > + return ret;
> > +
> > + val->intval = !!(reg & F_CHG_ACT);
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_charge(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + /*
> > + * To fit within 32 bits some values are rounded (uA/h)
> > + *
> > + * For Total Accumulated Charge Middle Low Byte register, addr
> > + * 03h, byte 2
> > + *
> > + * B0: 0.01084 mA/h rounded to 11 uA/h
> > + * B1: 0.02169 mA/h rounded to 22 uA/h
> > + * B2: 0.04340 mA/h rounded to 43 uA/h
> > + * B3: 0.08676 mA/h rounded to 87 uA/h
> > + * B4: 0.17350 mA/h rounded to 173 uÁ/h
> > + *
> > + * For Total Accumulated Charge Low Byte register, addr 04h,
> > + * byte 3
> > + *
> > + * B6: 0.00271 mA/h rounded to 3 uA/h
> > + * B7: 0.005422 mA/h rounded to 5 uA/h
> > + */
> > + static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
> > + 0, 0, 0, 0, 0, 0, 3, 5,
> > +
> > + 11, 22, 43, 87, 173, 347, 694, 1388,
> > +
> > + 2776, 5552, 11105, 22210, 44420, 88840, 177700, 355400,
> > +
> > + 710700, 1421000, 2843000, 5685000, 11371000, 22742000,
> > + 45484000, 90968000,
> > + };
> > + unsigned long total_acc_charger;
> > + unsigned int reg;
> > + int i, ret;
> > +
> > + ret = regmap_bulk_read(info->regmap, UCS1002_REG_TOTAL_ACC_CHARGE,
> > + ®, sizeof(u32));
> > + if (ret)
> > + return ret;
> > +
> > + total_acc_charger = be32_to_cpu(reg);
> > + val->intval = 0;
> > +
> > + for_each_set_bit(i, &total_acc_charger, ARRAY_SIZE(bit_weights_uAh))
> > + val->intval += bit_weights_uAh[i];
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_current(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + /*
> > + * The Current Measurement register stores the measured
> > + * current value delivered to the portable device. The range
> > + * is from 9.76 mA to 2.5 A.
> > + */
> > + static const int bit_weights_uA[BITS_PER_TYPE(u8)] = {
> > + 9760, 19500, 39000, 78100, 156200, 312300, 624600, 1249300,
> > + };
> > + unsigned long current_measurement;
> > + unsigned int reg;
> > + int i, ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_CURRENT_MEASUREMENT, ®);
> > + if (ret)
> > + return ret;
> > +
> > + current_measurement = reg;
> > + val->intval = 0;
> > +
> > + for_each_set_bit(i, ¤t_measurement, ARRAY_SIZE(bit_weights_uA))
> > + val->intval += bit_weights_uA[i];
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * The Current Limit register stores the maximum current used by the
> > + * port switch. The range is from 500mA to 2.5 A.
> > + */
> > +static const u32 ucs1002_current_limit_uA[] = {
> > + 500000, 900000, 1000000, 1200000, 1500000, 1800000, 2000000, 2500000,
> > +};
> > +
> > +static int ucs1002_get_max_current(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> > + if (ret)
> > + return ret;
> > +
> > + val->intval = ucs1002_current_limit_uA[reg & UCS1002_ILIM_SW_MASK];
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_set_max_current(struct ucs1002_info *info, u32 val)
> > +{
> > + unsigned int reg;
> > + int ret, idx;
> > +
> > + for (idx = 0; idx < ARRAY_SIZE(ucs1002_current_limit_uA); idx++) {
> > + if (val == ucs1002_current_limit_uA[idx])
> > + break;
> > + }
> > +
> > + if (idx == ARRAY_SIZE(ucs1002_current_limit_uA)) {
> > + dev_err(&info->client->dev,
> > + "%d is an invalid max current value\n", val);
>
> Here the error message is displayed as result of an attempt to set the current
> limit, which presumably can happen from userspace. This is inconsistent with
> the error returns below. I am not sure I understand why this would warrant an
> error log, but exceeding the limit set with the ILIM pin doesn't. I would
> suggest to drop this error message.
>
OK, will do in v2.
> > + return -EINVAL;
> > + }
> > +
> > + ret = regmap_write(info->regmap, UCS1002_REG_ILIMIT, idx);
> > + if (ret)
> > + return ret;
> > + /*
> > + * Any current limit setting exceeding the one set via ILIM
> > + * pin will be rejected, so we read out freshly changed limit
> > + * to make sure that it took effect.
> > + */
> > + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> > + if (ret)
> > + return ret;
> > +
> > + if (reg != idx)
> > + return -EINVAL;
> > +
> > + return 0;
> > +}
> > +
> > +static enum power_supply_usb_type ucs1002_usb_types[] = {
> > + POWER_SUPPLY_USB_TYPE_PD,
> > + POWER_SUPPLY_USB_TYPE_SDP,
> > + POWER_SUPPLY_USB_TYPE_DCP,
> > + POWER_SUPPLY_USB_TYPE_CDP,
> > + POWER_SUPPLY_USB_TYPE_UNKNOWN,
> > +};
> > +
> > +static int ucs1002_set_usb_type(struct ucs1002_info *info, int val)
> > +{
> > + unsigned int mode;
> > +
> > + if (val >= ARRAY_SIZE(ucs1002_usb_types))
> > + return -EINVAL;
> > +
> > + switch (ucs1002_usb_types[val]) {
> > + case POWER_SUPPLY_USB_TYPE_PD:
> > + mode = V_SET_ACTIVE_MODE_DEDICATED;
> > + break;
> > + case POWER_SUPPLY_USB_TYPE_SDP:
> > + mode = V_SET_ACTIVE_MODE_BC12_SDP;
> > + break;
> > + case POWER_SUPPLY_USB_TYPE_DCP:
> > + mode = V_SET_ACTIVE_MODE_BC12_DCP;
> > + break;
> > + case POWER_SUPPLY_USB_TYPE_CDP:
> > + mode = V_SET_ACTIVE_MODE_BC12_CDP;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> > + V_SET_ACTIVE_MODE_MASK, mode);
> > +}
> > +
> > +static int ucs1002_get_usb_type(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + enum power_supply_usb_type type;
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®);
> > + if (ret)
> > + return ret;
> > +
> > + switch (reg & F_ACTIVE_MODE_MASK) {
> > + default:
> > + type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
> > + break;
> > + case F_ACTIVE_MODE_DEDICATED:
> > + type = POWER_SUPPLY_USB_TYPE_PD;
> > + break;
> > + case F_ACTIVE_MODE_BC12_SDP:
> > + type = POWER_SUPPLY_USB_TYPE_SDP;
> > + break;
> > + case F_ACTIVE_MODE_BC12_DCP:
> > + type = POWER_SUPPLY_USB_TYPE_DCP;
> > + break;
> > + case F_ACTIVE_MODE_BC12_CDP:
> > + type = POWER_SUPPLY_USB_TYPE_CDP;
> > + break;
> > + };
> > +
> > + val->intval = type;
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_health(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + unsigned int reg;
> > + int ret, health;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_INTERRUPT_STATUS, ®);
> > + if (ret)
> > + return ret;
> > +
> > + if (reg & F_TSD)
> > + health = POWER_SUPPLY_HEALTH_OVERHEAT;
> > + else if (reg & (F_OVER_VOLT | F_BACK_VOLT))
> > + health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> > + else if (reg & F_OVER_ILIM)
> > + health = POWER_SUPPLY_HEALTH_OVERCURRENT;
> > + else if (reg & (F_DISCHARGE_ERR | F_MIN_KEEP_OUT))
> > + health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> > + else
> > + health = POWER_SUPPLY_HEALTH_GOOD;
> > +
> > + val->intval = health;
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_property(struct power_supply *psy,
> > + enum power_supply_property psp,
> > + union power_supply_propval *val)
> > +{
> > + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> > +
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_ONLINE:
> > + return ucs1002_get_online(info, val);
> > + case POWER_SUPPLY_PROP_CHARGE_NOW:
> > + return ucs1002_get_charge(info, val);
> > + case POWER_SUPPLY_PROP_CURRENT_NOW:
> > + return ucs1002_get_current(info, val);
> > + case POWER_SUPPLY_PROP_CURRENT_MAX:
> > + return ucs1002_get_max_current(info, val);
> > + case POWER_SUPPLY_PROP_USB_TYPE:
> > + return ucs1002_get_usb_type(info, val);
> > + case POWER_SUPPLY_PROP_HEALTH:
> > + return ucs1002_get_health(info, val);
> > + case POWER_SUPPLY_PROP_PRESENT:
> > + val->intval = info->present;
> > + return 0;
> > + case POWER_SUPPLY_PROP_MANUFACTURER:
> > + val->strval = UCS1002_MANUFACTURER;
> > + return 0;
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int ucs1002_set_property(struct power_supply *psy,
> > + enum power_supply_property psp,
> > + const union power_supply_propval *val)
> > +{
> > + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> > +
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_CURRENT_MAX:
> > + return ucs1002_set_max_current(info, val->intval);
> > + case POWER_SUPPLY_PROP_USB_TYPE:
> > + return ucs1002_set_usb_type(info, val->intval);
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int ucs1002_property_is_writeable(struct power_supply *psy,
> > + enum power_supply_property psp)
> > +{
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_CURRENT_MAX:
> > + case POWER_SUPPLY_PROP_USB_TYPE:
> > + return true;
> > + default:
> > + return false;
> > + }
> > +}
> > +
> > +static const struct power_supply_desc ucs1002_charger_desc = {
> > + .name = "ucs1002",
> > + .type = POWER_SUPPLY_TYPE_USB,
> > + .usb_types = ucs1002_usb_types,
> > + .num_usb_types = ARRAY_SIZE(ucs1002_usb_types),
> > + .get_property = ucs1002_get_property,
> > + .set_property = ucs1002_set_property,
> > + .property_is_writeable = ucs1002_property_is_writeable,
> > + .properties = ucs1002_props,
> > + .num_properties = ARRAY_SIZE(ucs1002_props),
> > +};
> > +
> > +static irqreturn_t ucs1002_charger_irq(int irq, void *data)
> > +{
> > + int ret, regval;
> > + bool present;
> > + struct ucs1002_info *info = data;
> > +
> > + present = info->present;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®val);
> > + if (ret)
> > + return IRQ_HANDLED;
> > +
> > + /* update attached status */
> > + info->present = (regval & F_ADET_PIN) ? true : false;
>
> !!(regval & F_ADET_PIN);
>
> would do.
>
Yeah, missed this one.
> > +
> > + /* notify the change */
> > + if (present != info->present)
> > + power_supply_changed(info->charger);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static irqreturn_t ucs1002_alert_irq(int irq, void *data)
> > +{
> > + struct ucs1002_info *info = data;
> > +
> > + power_supply_changed(info->charger);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static const struct regulator_ops ucs1002_regulator_ops = {
> > + .is_enabled = regulator_is_enabled_regmap,
> > + .enable = regulator_enable_regmap,
> > + .disable = regulator_disable_regmap,
> > +};
> > +
> > +static const struct regulator_desc ucs1002_regulator_descriptor = {
> > + .name = "ucs1002-vbus",
> > + .ops = &ucs1002_regulator_ops,
> > + .type = REGULATOR_VOLTAGE,
> > + .owner = THIS_MODULE,
> > + .enable_reg = UCS1002_REG_SWITCH_CFG,
> > + .enable_mask = F_PWR_EN_SET,
> > + .enable_val = F_PWR_EN_SET,
> > + .fixed_uV = 5000000,
> > + .n_voltages = 1,
> > +};
> > +
> > +static int ucs1002_probe(struct i2c_client *client,
> > + const struct i2c_device_id *dev_id)
> > +{
> > + struct device *dev = &client->dev;
> > + struct power_supply_config charger_config = {};
> > + const struct regmap_config regmap_config = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + };
> > + struct regulator_config regulator_config = {};
> > + int irq_a_det, irq_alert, ret;
> > + struct regulator_dev *rdev;
> > + struct ucs1002_info *info;
> > + unsigned int regval;
> > +
> > + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> > + if (!info)
> > + return -ENOMEM;
> > +
> > + info->regmap = devm_regmap_init_i2c(client, ®map_config);
> > + if (IS_ERR(info->regmap)) {
> > + ret = PTR_ERR(info->regmap);
> > + dev_err(dev, "regmap initialization failed: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + info->client = client;
> > +
> > + irq_a_det = of_irq_get_byname(dev->of_node, "a_det");
> > + irq_alert = of_irq_get_byname(dev->of_node, "alert");
> > +
> > + charger_config.of_node = dev->of_node;
> > + charger_config.drv_data = info;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_PRODUCT_ID, ®val);
> > + if (ret)
> > + return ret;
>
> Silent error ?
>
Will add some logging in v2.
> > +
> > + if (regval != UCS1002_PRODUCT_ID) {
> > + dev_err(dev,
> > + "Product ID does not match (0x%02x != 0x%02x)\n",
> > + regval, UCS1002_PRODUCT_ID);
> > + return -ENODEV;
> > + }
> > +
> > + dev_info(dev, "registered with product id 0x%02x\n", regval);
> > +
> Does that add any value ? After all, the displayed value is known to be
> UCS1002_PRODUCT_ID. It is also not really registered yet at this point.
>
I'll drop that message in v2.
> > + /* Enable charge rationing by default */
> > + ret = regmap_update_bits(info->regmap, UCS1002_REG_GENERAL_CFG,
> > + F_RATION_EN, F_RATION_EN);
> > + if (ret)
> > + return ret;
>
> Another silent error ? Seems odd, especially since we just above
> already claimed that the device was registered.
>
Will add logging in v2.
> > +
> > + dev_dbg(dev, "set active mode selection through i2c\n");
> > + /*
> > + * Ignore the M1, M2, PWR_EN, and EM_EN pin states. Set active
> > + * mode selection to Dedicated Charger Emulation Cycle.
> > + *
> > + * #M1 #M2 EM_EN
> > + * 0 0 1 - Dedicated Charger Emulation Cycle
> > + *
> > + */
> > + ret = regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> > + F_PIN_IGNORE | F_EM_EN_SET | F_M2_SET |
> > + F_M1_SET, F_PIN_IGNORE | F_EM_EN_SET);
> > + if (ret)
> > + return ret;
>
> And another one.
>
Ditto.
> > + /*
> > + * Be safe and set initial current limit to 500mA
> > + */
> > + ret = ucs1002_set_max_current(info, 500000);
> > + if (ret) {
> > + dev_err(dev, "Failed to read max current default\n");
>
> read ?
>
Ugh, my bad, will fix the message.
> > + return ret;
> > + }
> > +
> > + info->charger = devm_power_supply_register(dev, &ucs1002_charger_desc,
> > + &charger_config);
> > + if (IS_ERR(info->charger)) {
> > + dev_err(dev, "failed to register power supply\n");
> > + return PTR_ERR(info->charger);
> > + }
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®val);
> > + if (ret)
> > + return ret;
> > +
> > + info->regulator_descriptor =
> > + devm_kmemdup(dev, &ucs1002_regulator_descriptor,
> > + sizeof(ucs1002_regulator_descriptor),
> > + GFP_KERNEL);
>
> What if devm_kmemdup() returns NULL ?
>
Currently, just sadness. Will add a check for this in v2.
Thanks,
Andrey Smirnov
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-26 16:51 ` Enric Balletbo Serra
2019-04-26 17:04 ` Guenter Roeck
@ 2019-04-27 0:29 ` Andrey Smirnov
1 sibling, 0 replies; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-27 0:29 UTC (permalink / raw)
To: Enric Balletbo Serra
Cc: Linux PM list, Chris Health, Lucas Stach, Fabio Estevam,
Guenter Roeck, Sebastian Reichel, linux-kernel
On Fri, Apr 26, 2019 at 9:52 AM Enric Balletbo Serra
<eballetbo@gmail.com> wrote:
>
> Hi Andrey,
>
> Many thanks to push this upstream. Actually this the fifth version [1]
> of this patchset. I think that is interesting for the maintainers
> maintain the history and the changelog.
>
> [1] https://lkml.org/lkml/2016/3/14/233
I probably won't change the version numbering of the series at this
point, but I'll definitely add the link above to the cover letter.
>
> Missatge de Andrey Smirnov <andrew.smirnov@gmail.com> del dia dc., 17
> d’abr. 2019 a les 10:46:
> >
> > Add driver for Microchip UCS1002 Programmable USB Port Power
> > Controller with Charger Emulation. The driver exposed a power supply
> > device to control/monitor various parameter of the device as well as a
> > regulator to allow controlling VBUS line.
> >
> > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> > Cc: Chris Health <cphealy@gmail.com>
> > Cc: Lucas Stach <l.stach@pengutronix.de>
> > Cc: Fabio Estevam <fabio.estevam@nxp.com>
> > Cc: Guenter Roeck <linux@roeck-us.net>
> > Cc: Sebastian Reichel <sre@kernel.org>
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-pm@vger.kernel.org
> > ---
> > drivers/power/supply/Kconfig | 9 +
> > drivers/power/supply/Makefile | 1 +
> > drivers/power/supply/ucs1002_power.c | 639 +++++++++++++++++++++++++++
> > 3 files changed, 649 insertions(+)
> > create mode 100644 drivers/power/supply/ucs1002_power.c
> >
> > diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
> > index e901b9879e7e..c614c8a196f3 100644
> > --- a/drivers/power/supply/Kconfig
> > +++ b/drivers/power/supply/Kconfig
> > @@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
> > Say Y here to enable support for fuel gauge with SC27XX
> > PMIC chips.
> >
> > +config CHARGER_UCS1002
> > + tristate "Microchip UCS1002 USB Port Power Controller"
> > + depends on I2C
> > + depends on OF
> > + select REGMAP_I2C
> > + help
> > + Say Y to enable support for Microchip UCS1002 Programmable
> > + USB Port Power Controller with Charger Emulation.
> > +
> > endif # POWER_SUPPLY
> > diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
> > index b731c2a9b695..c56803a9e4fe 100644
> > --- a/drivers/power/supply/Makefile
> > +++ b/drivers/power/supply/Makefile
> > @@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
> > obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
> > obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
> > obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
> > +obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
> > diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c
> > new file mode 100644
> > index 000000000000..b0b81d62e003
> > --- /dev/null
> > +++ b/drivers/power/supply/ucs1002_power.c
> > @@ -0,0 +1,639 @@
> > +// SPDX-License-Identifier: GPL-2.0+
>
> There is a license mismatch, or this should be GPL-2.0 or
> MODULE_LICENCE should GPL.
>
OK, will change MODULE_LICENSE to GPL in v2.
> > +/*
> > + * Driver for UCS1002 Programmable USB Port Power Controller
> > + *
> > + * Copyright (C) 2019 Zodiac Inflight Innovations
> > + */
> > +#include <linux/freezer.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/i2c.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/kthread.h>
> > +#include <linux/device.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/power_supply.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/driver.h>
> > +#include <linux/regulator/of_regulator.h>
> > +
> > +/* UCS1002 Registers */
> > +#define UCS1002_REG_CURRENT_MEASUREMENT 0x00
> > +
> > +/*
> > + * The Total Accumulated Charge registers store the total accumulated
> > + * charge delivered from the VS source to a portable device. The total
> > + * value is calculated using four registers, from 01h to 04h. The bit
> > + * weighting of the registers is given in mA/hrs.
> > + */
> > +#define UCS1002_REG_TOTAL_ACC_CHARGE 0x01
> > +
> > +/* Other Status Register */
> > +#define UCS1002_REG_OTHER_STATUS 0x0f
> > +# define F_ADET_PIN BIT(4)
> > +# define F_CHG_ACT BIT(3)
> > +
> > +/* Interrupt Status */
> > +#define UCS1002_REG_INTERRUPT_STATUS 0x10
> > +# define F_DISCHARGE_ERR BIT(6)
> > +# define F_RESET BIT(5)
> > +# define F_MIN_KEEP_OUT BIT(4)
> > +# define F_TSD BIT(3)
> > +# define F_OVER_VOLT BIT(2)
> > +# define F_BACK_VOLT BIT(1)
> > +# define F_OVER_ILIM BIT(0)
> > +
> > +/* Pin Status Register */
> > +#define UCS1002_REG_PIN_STATUS 0x14
> > +# define UCS1002_PWR_STATE_MASK 0x03
> > +# define F_PWR_EN_PIN BIT(6)
> > +# define F_M2_PIN BIT(5)
> > +# define F_M1_PIN BIT(4)
> > +# define F_EM_EN_PIN BIT(3)
> > +# define F_SEL_PIN BIT(2)
> > +# define F_ACTIVE_MODE_MASK GENMASK(5, 3)
> > +# define F_ACTIVE_MODE_PASSTHROUGH F_M2_PIN
> > +# define F_ACTIVE_MODE_DEDICATED F_EM_EN_PIN
> > +# define F_ACTIVE_MODE_BC12_DCP (F_M2_PIN | F_EM_EN_PIN)
> > +# define F_ACTIVE_MODE_BC12_SDP F_M1_PIN
> > +# define F_ACTIVE_MODE_BC12_CDP (F_M1_PIN | F_M2_PIN | F_EM_EN_PIN)
> > +
> > +/* General Configuration Register */
> > +#define UCS1002_REG_GENERAL_CFG 0x15
> > +# define F_RATION_EN BIT(3)
> > +
> > +/* Emulation Configuration Register */
> > +#define UCS1002_REG_EMU_CFG 0x16
> > +
> > +/* Switch Configuration Register */
> > +#define UCS1002_REG_SWITCH_CFG 0x17
> > +# define F_PIN_IGNORE BIT(7)
> > +# define F_EM_EN_SET BIT(5)
> > +# define F_M2_SET BIT(4)
> > +# define F_M1_SET BIT(3)
> > +# define F_S0_SET BIT(2)
> > +# define F_PWR_EN_SET BIT(1)
> > +# define F_LATCH_SET BIT(0)
> > +# define V_SET_ACTIVE_MODE_MASK GENMASK(5, 3)
> > +# define V_SET_ACTIVE_MODE_PASSTHROUGH F_M2_SET
> > +# define V_SET_ACTIVE_MODE_DEDICATED F_EM_EN_SET
> > +# define V_SET_ACTIVE_MODE_BC12_DCP (F_M2_SET | F_EM_EN_SET)
> > +# define V_SET_ACTIVE_MODE_BC12_SDP F_M1_SET
> > +# define V_SET_ACTIVE_MODE_BC12_CDP (F_M1_SET | F_M2_SET | F_EM_EN_SET)
> > +
> > +/* Current Limit Register */
> > +#define UCS1002_REG_ILIMIT 0x19
> > +# define UCS1002_ILIM_SW_MASK GENMASK(3, 0)
> > +
> > +/* Product ID */
> > +#define UCS1002_REG_PRODUCT_ID 0xfd
> > +# define UCS1002_PRODUCT_ID 0x4e
> > +
> > +/* Manufacture name */
> > +#define UCS1002_MANUFACTURER "SMSC"
> > +
> > +struct ucs1002_info {
> > + struct power_supply *charger;
> > + struct i2c_client *client;
> > + struct regmap *regmap;
> > + struct regulator_desc *regulator_descriptor;
> > + bool present;
> > +};
> > +
> > +static enum power_supply_property ucs1002_props[] = {
> > + POWER_SUPPLY_PROP_ONLINE,
> > + POWER_SUPPLY_PROP_CHARGE_NOW,
> > + POWER_SUPPLY_PROP_CURRENT_NOW,
> > + POWER_SUPPLY_PROP_CURRENT_MAX,
> > + POWER_SUPPLY_PROP_PRESENT, /* the presence of PED */
> > + POWER_SUPPLY_PROP_MANUFACTURER,
> > + POWER_SUPPLY_PROP_USB_TYPE,
> > + POWER_SUPPLY_PROP_HEALTH,
> > +};
> > +
> > +static int ucs1002_get_online(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®);
> > + if (ret)
> > + return ret;
> > +
> > + val->intval = !!(reg & F_CHG_ACT);
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_charge(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + /*
> > + * To fit within 32 bits some values are rounded (uA/h)
> > + *
> > + * For Total Accumulated Charge Middle Low Byte register, addr
> > + * 03h, byte 2
> > + *
> > + * B0: 0.01084 mA/h rounded to 11 uA/h
> > + * B1: 0.02169 mA/h rounded to 22 uA/h
> > + * B2: 0.04340 mA/h rounded to 43 uA/h
> > + * B3: 0.08676 mA/h rounded to 87 uA/h
> > + * B4: 0.17350 mA/h rounded to 173 uÁ/h
> > + *
> > + * For Total Accumulated Charge Low Byte register, addr 04h,
> > + * byte 3
> > + *
> > + * B6: 0.00271 mA/h rounded to 3 uA/h
> > + * B7: 0.005422 mA/h rounded to 5 uA/h
> > + */
> > + static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
> > + 0, 0, 0, 0, 0, 0, 3, 5,
> > +
>
> nit: I personally don't like these empty lines here.
>
I'll add comments to clarify that those represent individual bytes to
replace the empty lines.
> > + 11, 22, 43, 87, 173, 347, 694, 1388,
> > +
> > + 2776, 5552, 11105, 22210, 44420, 88840, 177700, 355400,
> > +
> > + 710700, 1421000, 2843000, 5685000, 11371000, 22742000,
> > + 45484000, 90968000,
> > + };
> > + unsigned long total_acc_charger;
> > + unsigned int reg;
> > + int i, ret;
> > +
> > + ret = regmap_bulk_read(info->regmap, UCS1002_REG_TOTAL_ACC_CHARGE,
> > + ®, sizeof(u32));
> > + if (ret)
> > + return ret;
> > +
> > + total_acc_charger = be32_to_cpu(reg);
> > + val->intval = 0;
> > +
> > + for_each_set_bit(i, &total_acc_charger, ARRAY_SIZE(bit_weights_uAh))
> > + val->intval += bit_weights_uAh[i];
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_current(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + /*
> > + * The Current Measurement register stores the measured
> > + * current value delivered to the portable device. The range
> > + * is from 9.76 mA to 2.5 A.
> > + */
> > + static const int bit_weights_uA[BITS_PER_TYPE(u8)] = {
> > + 9760, 19500, 39000, 78100, 156200, 312300, 624600, 1249300,
> > + };
> > + unsigned long current_measurement;
> > + unsigned int reg;
> > + int i, ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_CURRENT_MEASUREMENT, ®);
> > + if (ret)
> > + return ret;
> > +
> > + current_measurement = reg;
> > + val->intval = 0;
> > +
> > + for_each_set_bit(i, ¤t_measurement, ARRAY_SIZE(bit_weights_uA))
> > + val->intval += bit_weights_uA[i];
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * The Current Limit register stores the maximum current used by the
> > + * port switch. The range is from 500mA to 2.5 A.
> > + */
> > +static const u32 ucs1002_current_limit_uA[] = {
> > + 500000, 900000, 1000000, 1200000, 1500000, 1800000, 2000000, 2500000,
> > +};
> > +
> > +static int ucs1002_get_max_current(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> > + if (ret)
> > + return ret;
> > +
> > + val->intval = ucs1002_current_limit_uA[reg & UCS1002_ILIM_SW_MASK];
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_set_max_current(struct ucs1002_info *info, u32 val)
> > +{
> > + unsigned int reg;
> > + int ret, idx;
> > +
> > + for (idx = 0; idx < ARRAY_SIZE(ucs1002_current_limit_uA); idx++) {
> > + if (val == ucs1002_current_limit_uA[idx])
> > + break;
> > + }
> > +
> > + if (idx == ARRAY_SIZE(ucs1002_current_limit_uA)) {
> > + dev_err(&info->client->dev,
> > + "%d is an invalid max current value\n", val);
> > + return -EINVAL;
> > + }
> > +
> > + ret = regmap_write(info->regmap, UCS1002_REG_ILIMIT, idx);
> > + if (ret)
> > + return ret;
> > + /*
> > + * Any current limit setting exceeding the one set via ILIM
> > + * pin will be rejected, so we read out freshly changed limit
> > + * to make sure that it took effect.
> > + */
> > + ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
> > + if (ret)
> > + return ret;
> > +
> > + if (reg != idx)
> > + return -EINVAL;
> > +
> > + return 0;
> > +}
> > +
> > +static enum power_supply_usb_type ucs1002_usb_types[] = {
> > + POWER_SUPPLY_USB_TYPE_PD,
> > + POWER_SUPPLY_USB_TYPE_SDP,
> > + POWER_SUPPLY_USB_TYPE_DCP,
> > + POWER_SUPPLY_USB_TYPE_CDP,
> > + POWER_SUPPLY_USB_TYPE_UNKNOWN,
> > +};
> > +
> > +static int ucs1002_set_usb_type(struct ucs1002_info *info, int val)
> > +{
> > + unsigned int mode;
> > +
> > + if (val >= ARRAY_SIZE(ucs1002_usb_types))
> > + return -EINVAL;
> > +
> > + switch (ucs1002_usb_types[val]) {
> > + case POWER_SUPPLY_USB_TYPE_PD:
> > + mode = V_SET_ACTIVE_MODE_DEDICATED;
> > + break;
> > + case POWER_SUPPLY_USB_TYPE_SDP:
> > + mode = V_SET_ACTIVE_MODE_BC12_SDP;
> > + break;
> > + case POWER_SUPPLY_USB_TYPE_DCP:
> > + mode = V_SET_ACTIVE_MODE_BC12_DCP;
> > + break;
> > + case POWER_SUPPLY_USB_TYPE_CDP:
> > + mode = V_SET_ACTIVE_MODE_BC12_CDP;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> > + V_SET_ACTIVE_MODE_MASK, mode);
> > +}
> > +
> > +static int ucs1002_get_usb_type(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + enum power_supply_usb_type type;
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®);
> > + if (ret)
> > + return ret;
> > +
> > + switch (reg & F_ACTIVE_MODE_MASK) {
> > + default:
> > + type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
> > + break;
> > + case F_ACTIVE_MODE_DEDICATED:
> > + type = POWER_SUPPLY_USB_TYPE_PD;
> > + break;
> > + case F_ACTIVE_MODE_BC12_SDP:
> > + type = POWER_SUPPLY_USB_TYPE_SDP;
> > + break;
> > + case F_ACTIVE_MODE_BC12_DCP:
> > + type = POWER_SUPPLY_USB_TYPE_DCP;
> > + break;
> > + case F_ACTIVE_MODE_BC12_CDP:
> > + type = POWER_SUPPLY_USB_TYPE_CDP;
> > + break;
> > + };
> > +
> > + val->intval = type;
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_health(struct ucs1002_info *info,
> > + union power_supply_propval *val)
> > +{
> > + unsigned int reg;
> > + int ret, health;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_INTERRUPT_STATUS, ®);
> > + if (ret)
> > + return ret;
> > +
> > + if (reg & F_TSD)
> > + health = POWER_SUPPLY_HEALTH_OVERHEAT;
> > + else if (reg & (F_OVER_VOLT | F_BACK_VOLT))
> > + health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> > + else if (reg & F_OVER_ILIM)
> > + health = POWER_SUPPLY_HEALTH_OVERCURRENT;
> > + else if (reg & (F_DISCHARGE_ERR | F_MIN_KEEP_OUT))
> > + health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> > + else
> > + health = POWER_SUPPLY_HEALTH_GOOD;
> > +
> > + val->intval = health;
> > +
> > + return 0;
> > +}
> > +
> > +static int ucs1002_get_property(struct power_supply *psy,
> > + enum power_supply_property psp,
> > + union power_supply_propval *val)
> > +{
> > + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> > +
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_ONLINE:
> > + return ucs1002_get_online(info, val);
> > + case POWER_SUPPLY_PROP_CHARGE_NOW:
> > + return ucs1002_get_charge(info, val);
> > + case POWER_SUPPLY_PROP_CURRENT_NOW:
> > + return ucs1002_get_current(info, val);
> > + case POWER_SUPPLY_PROP_CURRENT_MAX:
> > + return ucs1002_get_max_current(info, val);
> > + case POWER_SUPPLY_PROP_USB_TYPE:
> > + return ucs1002_get_usb_type(info, val);
> > + case POWER_SUPPLY_PROP_HEALTH:
> > + return ucs1002_get_health(info, val);
> > + case POWER_SUPPLY_PROP_PRESENT:
> > + val->intval = info->present;
> > + return 0;
> > + case POWER_SUPPLY_PROP_MANUFACTURER:
> > + val->strval = UCS1002_MANUFACTURER;
> > + return 0;
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int ucs1002_set_property(struct power_supply *psy,
> > + enum power_supply_property psp,
> > + const union power_supply_propval *val)
> > +{
> > + struct ucs1002_info *info = power_supply_get_drvdata(psy);
> > +
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_CURRENT_MAX:
> > + return ucs1002_set_max_current(info, val->intval);
> > + case POWER_SUPPLY_PROP_USB_TYPE:
> > + return ucs1002_set_usb_type(info, val->intval);
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int ucs1002_property_is_writeable(struct power_supply *psy,
> > + enum power_supply_property psp)
> > +{
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_CURRENT_MAX:
> > + case POWER_SUPPLY_PROP_USB_TYPE:
> > + return true;
> > + default:
> > + return false;
> > + }
> > +}
> > +
> > +static const struct power_supply_desc ucs1002_charger_desc = {
> > + .name = "ucs1002",
> > + .type = POWER_SUPPLY_TYPE_USB,
> > + .usb_types = ucs1002_usb_types,
> > + .num_usb_types = ARRAY_SIZE(ucs1002_usb_types),
> > + .get_property = ucs1002_get_property,
> > + .set_property = ucs1002_set_property,
> > + .property_is_writeable = ucs1002_property_is_writeable,
> > + .properties = ucs1002_props,
> > + .num_properties = ARRAY_SIZE(ucs1002_props),
> > +};
> > +
> > +static irqreturn_t ucs1002_charger_irq(int irq, void *data)
> > +{
> > + int ret, regval;
> > + bool present;
> > + struct ucs1002_info *info = data;
> > +
> > + present = info->present;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®val);
> > + if (ret)
> > + return IRQ_HANDLED;
> > +
> > + /* update attached status */
> > + info->present = (regval & F_ADET_PIN) ? true : false;
> > +
> > + /* notify the change */
> > + if (present != info->present)
> > + power_supply_changed(info->charger);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static irqreturn_t ucs1002_alert_irq(int irq, void *data)
> > +{
> > + struct ucs1002_info *info = data;
> > +
> > + power_supply_changed(info->charger);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static const struct regulator_ops ucs1002_regulator_ops = {
> > + .is_enabled = regulator_is_enabled_regmap,
> > + .enable = regulator_enable_regmap,
> > + .disable = regulator_disable_regmap,
> > +};
> > +
> > +static const struct regulator_desc ucs1002_regulator_descriptor = {
> > + .name = "ucs1002-vbus",
> > + .ops = &ucs1002_regulator_ops,
> > + .type = REGULATOR_VOLTAGE,
> > + .owner = THIS_MODULE,
> > + .enable_reg = UCS1002_REG_SWITCH_CFG,
> > + .enable_mask = F_PWR_EN_SET,
> > + .enable_val = F_PWR_EN_SET,
> > + .fixed_uV = 5000000,
> > + .n_voltages = 1,
> > +};
> > +
> > +static int ucs1002_probe(struct i2c_client *client,
> > + const struct i2c_device_id *dev_id)
> > +{
> > + struct device *dev = &client->dev;
> > + struct power_supply_config charger_config = {};
> > + const struct regmap_config regmap_config = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + };
> > + struct regulator_config regulator_config = {};
> > + int irq_a_det, irq_alert, ret;
> > + struct regulator_dev *rdev;
> > + struct ucs1002_info *info;
> > + unsigned int regval;
> > +
> > + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> > + if (!info)
> > + return -ENOMEM;
> > +
> > + info->regmap = devm_regmap_init_i2c(client, ®map_config);
> > + if (IS_ERR(info->regmap)) {
> > + ret = PTR_ERR(info->regmap);
> > + dev_err(dev, "regmap initialization failed: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + info->client = client;
> > +
> > + irq_a_det = of_irq_get_byname(dev->of_node, "a_det");
> > + irq_alert = of_irq_get_byname(dev->of_node, "alert");
> > +
> > + charger_config.of_node = dev->of_node;
> > + charger_config.drv_data = info;
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_PRODUCT_ID, ®val);
> > + if (ret)
> > + return ret;
> > +
> > + if (regval != UCS1002_PRODUCT_ID) {
> > + dev_err(dev,
> > + "Product ID does not match (0x%02x != 0x%02x)\n",
> > + regval, UCS1002_PRODUCT_ID);
> > + return -ENODEV;
> > + }
> > +
> > + dev_info(dev, "registered with product id 0x%02x\n", regval);
> > +
> > + /* Enable charge rationing by default */
> > + ret = regmap_update_bits(info->regmap, UCS1002_REG_GENERAL_CFG,
> > + F_RATION_EN, F_RATION_EN);
> > + if (ret)
> > + return ret;
> > +
> > + dev_dbg(dev, "set active mode selection through i2c\n");
> > + /*
> > + * Ignore the M1, M2, PWR_EN, and EM_EN pin states. Set active
> > + * mode selection to Dedicated Charger Emulation Cycle.
> > + *
> > + * #M1 #M2 EM_EN
> > + * 0 0 1 - Dedicated Charger Emulation Cycle
> > + *
> > + */
> > + ret = regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
> > + F_PIN_IGNORE | F_EM_EN_SET | F_M2_SET |
> > + F_M1_SET, F_PIN_IGNORE | F_EM_EN_SET);
> > + if (ret)
> > + return ret;
> > + /*
> > + * Be safe and set initial current limit to 500mA
> > + */
> > + ret = ucs1002_set_max_current(info, 500000);
> > + if (ret) {
> > + dev_err(dev, "Failed to read max current default\n");
> > + return ret;
> > + }
> > +
> > + info->charger = devm_power_supply_register(dev, &ucs1002_charger_desc,
> > + &charger_config);
> > + if (IS_ERR(info->charger)) {
> > + dev_err(dev, "failed to register power supply\n");
> > + return PTR_ERR(info->charger);
> > + }
> > +
> > + ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®val);
> > + if (ret)
> > + return ret;
> > +
> > + info->regulator_descriptor =
> > + devm_kmemdup(dev, &ucs1002_regulator_descriptor,
> > + sizeof(ucs1002_regulator_descriptor),
> > + GFP_KERNEL);
> > + info->regulator_descriptor->enable_is_inverted = !(regval & F_SEL_PIN);
> > +
> > + regulator_config.dev = dev;
> > + regulator_config.of_node = dev->of_node;
> > + regulator_config.regmap = info->regmap;
> > +
> > + rdev = devm_regulator_register(dev, info->regulator_descriptor,
> > + ®ulator_config);
> > + if (IS_ERR(rdev)) {
> > + dev_err(dev, "failed to register VBUS regulator\n");
> > + return PTR_ERR(rdev);
> > + }
> > +
> > + if (irq_a_det > 0) {
> > + ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
> > + ucs1002_charger_irq,
> > + IRQF_TRIGGER_FALLING |
> > + IRQF_TRIGGER_RISING |
> > + IRQF_ONESHOT,
> > + "ucs1002-a_det", info);
> > + if (ret) {
> > + dev_err(dev, "failed to request A_DET threaded irq\n");
> > + return ret;
> > + }
> > + }
> > +
> > + if (irq_alert > 0) {
> > + ret = devm_request_threaded_irq(dev, irq_alert, NULL,
> > + ucs1002_alert_irq,
> > + IRQF_TRIGGER_FALLING |
> > + IRQF_TRIGGER_RISING |
> > + IRQF_ONESHOT,
> > + "ucs1002-alert", info);
> > + if (ret) {
> > + dev_err(dev, "failed to request ALERT threaded irq\n");
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +#if IS_ENABLED(CONFIG_OF)
>
> This driver is DT only, this if is not needed.
>
Missed this, will drop in v2.
> > +static const struct of_device_id ucs1002_of_match[] = {
> > + { .compatible = "microchip,ucs1002", },
> > + { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, ucs1002_of_match);
> > +#endif
> > +
> > +static const struct i2c_device_id ucs1002_ids[] = {
> > + {"ucs1002", 0},
> > + { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(i2c, ucs1002_ids);
> > +
> > +static struct i2c_driver ucs1002_driver = {
> > + .driver = {
> > + .name = "ucs1002",
> > + .of_match_table = of_match_ptr(ucs1002_of_match),
>
> No need to use of_match_ptr, is DT-only.
>
Ditto.
> > + },
> > + .probe = ucs1002_probe,
> > +};
> > +module_i2c_driver(ucs1002_driver);
> > +
> > +MODULE_DESCRIPTION("Microchip UCS1002 Programmable USB Port Power Controller");
> > +MODULE_AUTHOR("Enric Balletbo Serra <enric.balletbo@collabora.com>");
>
> I'm not sure how much differs this patch from the one I sent 3 years
> ago ... but if i'm the author or co-author you should add the
> signed-off-by.
>
> [1] https://lkml.org/lkml/2016/3/14/233
> [2] https://www.spinics.net/lists/devicetree/msg122745.html
>
Yeah, you're right. Will add in v2.
Thanks,
Andrey Smirnov
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-26 14:43 ` Lucas Stach
@ 2019-04-28 22:24 ` Andrey Smirnov
0 siblings, 0 replies; 13+ messages in thread
From: Andrey Smirnov @ 2019-04-28 22:24 UTC (permalink / raw)
To: Lucas Stach
Cc: Linux PM list, Chris Health, Fabio Estevam, Guenter Roeck,
Sebastian Reichel, linux-kernel
On Fri, Apr 26, 2019 at 7:43 AM Lucas Stach <l.stach@pengutronix.de> wrote:
>
> Hi Andrey,
>
> Am Mittwoch, den 17.04.2019, 01:44 -0700 schrieb Andrey Smirnov:
> > Add driver for Microchip UCS1002 Programmable USB Port Power
> > Controller with Charger Emulation. The driver exposed a power supply
> > device to control/monitor various parameter of the device as well as a
> > regulator to allow controlling VBUS line.
> >
> > > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
> > > Cc: Chris Health <cphealy@gmail.com>
> > > Cc: Lucas Stach <l.stach@pengutronix.de>
> > > Cc: Fabio Estevam <fabio.estevam@nxp.com>
> > > Cc: Guenter Roeck <linux@roeck-us.net>
> > > Cc: Sebastian Reichel <sre@kernel.org>
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-pm@vger.kernel.org
> > ---
> [...]
> > + if (irq_a_det > 0) {
> > > + ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
> > > + ucs1002_charger_irq,
> > > + IRQF_TRIGGER_FALLING |
> > > + IRQF_TRIGGER_RISING |
> > > + IRQF_ONESHOT,
> > > + "ucs1002-a_det", info);
> > > + if (ret) {
> > > + dev_err(dev, "failed to request A_DET threaded irq\n");
> > > + return ret;
> > > + }
> > > + }
> > +
> > > + if (irq_alert > 0) {
> > > + ret = devm_request_threaded_irq(dev, irq_alert, NULL,
> > > + ucs1002_alert_irq,
> > > + IRQF_TRIGGER_FALLING |
> > > + IRQF_TRIGGER_RISING |
> > > + IRQF_ONESHOT,
> > > + "ucs1002-alert", info);
> > > + if (ret) {
> > > + dev_err(dev, "failed to request ALERT threaded irq\n");
> > > + return ret;
> > > + }
> > > + }
>
> Any reason to explicitly set the IRQ trigger type here? Normally I
> would expect this to be set via the DT interrupt specifier.
>
Don't have a particular reason. I'll move it to DT.
Thanks,
Andrey Smirnov
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2019-04-28 22:24 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-04-17 8:44 [PATCH 0/3] Driver for UCS1002 Andrey Smirnov
2019-04-17 8:44 ` [PATCH 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant Andrey Smirnov
2019-04-26 16:12 ` Guenter Roeck
2019-04-17 8:44 ` [PATCH 2/3] power: supply: Add driver for Microchip UCS1002 Andrey Smirnov
2019-04-26 14:43 ` Lucas Stach
2019-04-28 22:24 ` Andrey Smirnov
2019-04-26 16:10 ` Guenter Roeck
2019-04-27 0:16 ` Andrey Smirnov
2019-04-26 16:51 ` Enric Balletbo Serra
2019-04-26 17:04 ` Guenter Roeck
2019-04-27 0:29 ` Andrey Smirnov
2019-04-17 8:44 ` [PATCH 3/3] dt-bindings: power: supply: Add bindings " Andrey Smirnov
2019-04-17 19:05 ` Fabio Estevam
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).