From: Yu Chen <chenyu56@huawei.com>
To: <linux-usb@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Cc: <john.stultz@linaro.org>, <suzhuangluan@hisilicon.com>,
<kongfei@hisilicon.com>, <liuyu712@hisilicon.com>,
<wanghu17@hisilicon.com>, <butao@hisilicon.com>,
<chenyao11@huawei.com>, <fangshengzhou@hisilicon.com>,
<lipengcheng8@huawei.com>, <songxiaowei@hisilicon.com>,
<xuyiping@hisilicon.com>, <xuyoujun4@huawei.com>,
<yudongbin@hisilicon.com>, <zangleigang@hisilicon.com>,
Yu Chen <chenyu56@huawei.com>,
Andy Shevchenko <andy.shevchenko@gmail.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
"David S. Miller" <davem@davemloft.net>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>,
Andrew Morton <akpm@linux-foundation.org>,
"Arnd Bergmann" <arnd@arndb.de>, Shawn Guo <shawnguo@kernel.org>,
Pengcheng Li <lpc.li@hisilicon.com>,
Jianguo Sun <sunjianguo1@huawei.com>,
Masahiro Yamada <yamada.masahiro@socionext.com>,
Jiancheng Xue <xuejiancheng@hisilicon.com>,
Binghui Wang <wangbinghui@hisilicon.com>
Subject: [PATCH v6 07/13] phy: Add usb phy support for hi3660 Soc of Hisilicon
Date: Sat, 20 Apr 2019 14:40:13 +0800 [thread overview]
Message-ID: <20190420064019.57522-8-chenyu56@huawei.com> (raw)
In-Reply-To: <20190420064019.57522-1-chenyu56@huawei.com>
This driver handles usb phy power on and shutdown for hi3660 Soc of
Hisilicon.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Pengcheng Li <lpc.li@hisilicon.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jiancheng Xue <xuejiancheng@hisilicon.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
---
v1:
* Remove unused code and add comment for time delay as suggested by
Kishon Vijay Abraham I.
v2:
* Fix license declaration.
* Remove redundant parens.
* Remove unused member variables in struct hi3660_priv.
v4:
* Add comments for HI3660_USB_DEFAULT_PHY_PARAM.
* Add margin for usleep_range.
* Get regmap of otg_bc from parent's of_node.
---
---
MAINTAINERS | 8 ++
drivers/phy/hisilicon/Kconfig | 10 ++
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3660-usb3.c | 233 ++++++++++++++++++++++++++++++++
4 files changed, 252 insertions(+)
create mode 100644 drivers/phy/hisilicon/phy-hi3660-usb3.c
diff --git a/MAINTAINERS b/MAINTAINERS
index d18b4d62cc21..d2c161e7a085 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16084,6 +16084,14 @@ L: linux-usb@vger.kernel.org
S: Maintained
F: drivers/usb/roles/intel-xhci-usb-role-switch.c
+USB IP DRIVER FOR HISILICON KIRIN
+M: Yu Chen <chenyu56@huawei.com>
+M: Binghui Wang <wangbinghui@hisilicon.com>
+L: linux-usb@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/phy/phy-hi3660-usb3.txt
+F: drivers/phy/hisilicon/phy-hi3660-usb3.c
+
USB ISP116X DRIVER
M: Olav Kongas <ok@artecdesign.ee>
L: linux-usb@vger.kernel.org
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index b40ee54a1a50..3c142f08987c 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -12,6 +12,16 @@ config PHY_HI6220_USB
To compile this driver as a module, choose M here.
+config PHY_HI3660_USB
+ tristate "hi3660 USB PHY support"
+ depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HISILICON HI3660 USB PHY.
+
+ To compile this driver as a module, choose M here.
+
config PHY_HISTB_COMBPHY
tristate "HiSilicon STB SoCs COMBPHY support"
depends on (ARCH_HISI && ARM64) || COMPILE_TEST
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index f662a4fe18d8..75ba64e2faf8 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -1,4 +1,5 @@
obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
+obj-$(CONFIG_PHY_HI3660_USB) += phy-hi3660-usb3.o
obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o
obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
diff --git a/drivers/phy/hisilicon/phy-hi3660-usb3.c b/drivers/phy/hisilicon/phy-hi3660-usb3.c
new file mode 100644
index 000000000000..cc0af2c044d0
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi3660-usb3.c
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Phy provider for USB 3.0 controller on HiSilicon 3660 platform
+ *
+ * Copyright (C) 2017-2018 Hilisicon Electronics Co., Ltd.
+ * http://www.huawei.com
+ *
+ * Authors: Yu Chen <chenyu56@huawei.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define PERI_CRG_CLK_EN4 0x40
+#define PERI_CRG_CLK_DIS4 0x44
+#define GT_CLK_USB3OTG_REF BIT(0)
+#define GT_ACLK_USB3OTG BIT(1)
+
+#define PERI_CRG_RSTEN4 0x90
+#define PERI_CRG_RSTDIS4 0x94
+#define IP_RST_USB3OTGPHY_POR BIT(3)
+#define IP_RST_USB3OTG BIT(5)
+
+#define PERI_CRG_ISODIS 0x148
+#define USB_REFCLK_ISO_EN BIT(25)
+
+#define PCTRL_PERI_CTRL3 0x10
+#define PCTRL_PERI_CTRL3_MSK_START 16
+#define USB_TCXO_EN BIT(1)
+
+#define PCTRL_PERI_CTRL24 0x64
+#define SC_CLK_USB3PHY_3MUX1_SEL BIT(25)
+
+#define USBOTG3_CTRL0 0x00
+#define SC_USB3PHY_ABB_GT_EN BIT(15)
+
+#define USBOTG3_CTRL2 0x08
+#define USBOTG3CTRL2_POWERDOWN_HSP BIT(0)
+#define USBOTG3CTRL2_POWERDOWN_SSP BIT(1)
+
+#define USBOTG3_CTRL3 0x0C
+#define USBOTG3_CTRL3_VBUSVLDEXT BIT(6)
+#define USBOTG3_CTRL3_VBUSVLDEXTSEL BIT(5)
+
+#define USBOTG3_CTRL4 0x10
+
+#define USBOTG3_CTRL7 0x1c
+#define REF_SSP_EN BIT(16)
+
+/* This value config the default txtune parameter of the usb 2.0 phy */
+#define HI3660_USB_DEFAULT_PHY_PARAM 0x1c466e3
+
+struct hi3660_priv {
+ struct device *dev;
+ struct regmap *peri_crg;
+ struct regmap *pctrl;
+ struct regmap *otg_bc;
+ u32 eye_diagram_param;
+};
+
+static int hi3660_phy_init(struct phy *phy)
+{
+ struct hi3660_priv *priv = phy_get_drvdata(phy);
+ u32 val, mask;
+ int ret;
+
+ /* usb refclk iso disable */
+ ret = regmap_write(priv->peri_crg, PERI_CRG_ISODIS, USB_REFCLK_ISO_EN);
+ if (ret)
+ goto out;
+
+ /* enable usb_tcxo_en */
+ val = USB_TCXO_EN | (USB_TCXO_EN << PCTRL_PERI_CTRL3_MSK_START);
+ ret = regmap_write(priv->pctrl, PCTRL_PERI_CTRL3, val);
+ if (ret)
+ goto out;
+
+ /* assert phy */
+ val = IP_RST_USB3OTGPHY_POR | IP_RST_USB3OTG;
+ ret = regmap_write(priv->peri_crg, PERI_CRG_RSTEN4, val);
+ if (ret)
+ goto out;
+
+ /* enable phy ref clk */
+ val = SC_USB3PHY_ABB_GT_EN;
+ mask = val;
+ ret = regmap_update_bits(priv->otg_bc, USBOTG3_CTRL0, mask, val);
+ if (ret)
+ goto out;
+
+ val = REF_SSP_EN;
+ mask = val;
+ ret = regmap_update_bits(priv->otg_bc, USBOTG3_CTRL7, mask, val);
+ if (ret)
+ goto out;
+
+ /* exit from IDDQ mode */
+ mask = USBOTG3CTRL2_POWERDOWN_HSP | USBOTG3CTRL2_POWERDOWN_SSP;
+ ret = regmap_update_bits(priv->otg_bc, USBOTG3_CTRL2, mask, 0);
+ if (ret)
+ goto out;
+
+ /* delay for exit from IDDQ mode */
+ usleep_range(100, 120);
+
+ /* deassert phy */
+ val = IP_RST_USB3OTGPHY_POR | IP_RST_USB3OTG;
+ ret = regmap_write(priv->peri_crg, PERI_CRG_RSTDIS4, val);
+ if (ret)
+ goto out;
+
+ /* delay for phy deasserted */
+ usleep_range(10000, 15000);
+
+ /* fake vbus valid signal */
+ val = USBOTG3_CTRL3_VBUSVLDEXT | USBOTG3_CTRL3_VBUSVLDEXTSEL;
+ mask = val;
+ ret = regmap_update_bits(priv->otg_bc, USBOTG3_CTRL3, mask, val);
+ if (ret)
+ goto out;
+
+ /* delay for vbus valid */
+ usleep_range(100, 120);
+
+ ret = regmap_write(priv->otg_bc, USBOTG3_CTRL4,
+ priv->eye_diagram_param);
+ if (ret)
+ goto out;
+
+ return 0;
+out:
+ dev_err(priv->dev, "failed to init phy ret: %d\n", ret);
+ return ret;
+}
+
+static int hi3660_phy_exit(struct phy *phy)
+{
+ struct hi3660_priv *priv = phy_get_drvdata(phy);
+ u32 val;
+ int ret;
+
+ /* assert phy */
+ val = IP_RST_USB3OTGPHY_POR;
+ ret = regmap_write(priv->peri_crg, PERI_CRG_RSTEN4, val);
+ if (ret)
+ goto out;
+
+ /* disable usb_tcxo_en */
+ val = USB_TCXO_EN << PCTRL_PERI_CTRL3_MSK_START;
+ ret = regmap_write(priv->pctrl, PCTRL_PERI_CTRL3, val);
+ if (ret)
+ goto out;
+
+ return 0;
+out:
+ dev_err(priv->dev, "failed to exit phy ret: %d\n", ret);
+ return ret;
+}
+
+static struct phy_ops hi3660_phy_ops = {
+ .init = hi3660_phy_init,
+ .exit = hi3660_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int hi3660_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct phy *phy;
+ struct hi3660_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = dev;
+ priv->peri_crg = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "hisilicon,pericrg-syscon");
+ if (IS_ERR(priv->peri_crg)) {
+ dev_err(dev, "no hisilicon,pericrg-syscon\n");
+ return PTR_ERR(priv->peri_crg);
+ }
+
+ priv->pctrl = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "hisilicon,pctrl-syscon");
+ if (IS_ERR(priv->pctrl)) {
+ dev_err(dev, "no hisilicon,pctrl-syscon\n");
+ return PTR_ERR(priv->pctrl);
+ }
+
+ /* node of hi3660 phy is a sub-node of usb3_otg_bc */
+ priv->otg_bc = syscon_node_to_regmap(dev->parent->of_node);
+ if (IS_ERR(priv->otg_bc)) {
+ dev_err(dev, "no hisilicon,usb3-otg-bc-syscon\n");
+ return PTR_ERR(priv->otg_bc);
+ }
+
+ if (of_property_read_u32(dev->of_node, "hisilicon,eye-diagram-param",
+ &(priv->eye_diagram_param)))
+ priv->eye_diagram_param = HI3660_USB_DEFAULT_PHY_PARAM;
+
+ phy = devm_phy_create(dev, NULL, &hi3660_phy_ops);
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
+
+ phy_set_drvdata(phy, priv);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi3660_phy_of_match[] = {
+ {.compatible = "hisilicon,hi3660-usb-phy",},
+ { }
+};
+MODULE_DEVICE_TABLE(of, hi3660_phy_of_match);
+
+static struct platform_driver hi3660_phy_driver = {
+ .probe = hi3660_phy_probe,
+ .driver = {
+ .name = "hi3660-usb-phy",
+ .of_match_table = hi3660_phy_of_match,
+ }
+};
+module_platform_driver(hi3660_phy_driver);
+
+MODULE_AUTHOR("Yu Chen <chenyu56@huawei.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Hilisicon Hi3660 USB3 PHY Driver");
--
2.15.0-rc2
next prev parent reply other threads:[~2019-04-20 6:41 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-20 6:40 [PATCH v6 00/13] Add support for usb on Hikey960 Yu Chen
2019-04-20 6:40 ` [PATCH v6 01/13] dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY Yu Chen
2019-04-20 6:40 ` [PATCH v6 02/13] dt-bindings: misc: Add bindings for HiSilicon usb hub and data role switch functionality on HiKey960 Yu Chen
2019-04-25 21:35 ` Rob Herring
2019-04-30 6:07 ` Chen Yu
2019-05-01 16:27 ` Rob Herring
2019-04-20 6:40 ` [PATCH v6 03/13] usb: dwc3: dwc3-of-simple: Add support for dwc3 of Hisilicon Soc Platform Yu Chen
2019-04-25 21:36 ` Rob Herring
2019-04-20 6:40 ` [PATCH v6 04/13] usb: dwc3: Add splitdisable quirk for Hisilicon Kirin Soc Yu Chen
2020-09-07 13:06 ` Mauro Carvalho Chehab
2020-09-07 14:04 ` Felipe Balbi
2020-09-07 14:50 ` Mauro Carvalho Chehab
2020-09-08 6:09 ` Felipe Balbi
2020-09-08 6:49 ` Mauro Carvalho Chehab
2020-09-08 17:40 ` Thinh Nguyen
2020-09-08 6:42 ` Mauro Carvalho Chehab
2019-04-20 6:40 ` [PATCH v6 05/13] usb: dwc3: Execute GCTL Core Soft Reset while switch mdoe " Yu Chen
2019-04-20 6:40 ` [PATCH v6 06/13] usb: dwc3: Increase timeout for CmdAct cleared by device controller Yu Chen
2019-04-20 6:40 ` Yu Chen [this message]
2019-04-20 6:40 ` [PATCH v6 08/13] usb: roles: Introduce stubs for the exiting functions in role.h Yu Chen
2019-04-20 6:40 ` [PATCH v6 09/13] usb: roles: Add usb role switch notifier Yu Chen
2019-04-20 6:40 ` [PATCH v6 10/13] usb: dwc3: Registering a role switch in the DRD code Yu Chen
2019-04-20 6:40 ` [PATCH v6 11/13] hikey960: Support usb functionality of Hikey960 Yu Chen
2019-04-20 6:40 ` [PATCH v6 12/13] usb: gadget: Add configfs attribuite for controling match_existing_only Yu Chen
2019-04-20 6:40 ` [PATCH v6 13/13] dts: hi3660: Add support for usb on Hikey960 Yu Chen
2019-04-25 22:00 ` Rob Herring
2019-04-30 7:15 ` Chen Yu
2019-05-02 5:44 ` shufan_lee(李書帆)
2019-04-29 15:42 ` [PATCH v6 00/13] " Valentin Schneider
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190420064019.57522-8-chenyu56@huawei.com \
--to=chenyu56@huawei.com \
--cc=akpm@linux-foundation.org \
--cc=andy.shevchenko@gmail.com \
--cc=arnd@arndb.de \
--cc=butao@hisilicon.com \
--cc=chenyao11@huawei.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=fangshengzhou@hisilicon.com \
--cc=gregkh@linuxfoundation.org \
--cc=john.stultz@linaro.org \
--cc=kishon@ti.com \
--cc=kongfei@hisilicon.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=lipengcheng8@huawei.com \
--cc=liuyu712@hisilicon.com \
--cc=lpc.li@hisilicon.com \
--cc=mchehab+samsung@kernel.org \
--cc=shawnguo@kernel.org \
--cc=songxiaowei@hisilicon.com \
--cc=sunjianguo1@huawei.com \
--cc=suzhuangluan@hisilicon.com \
--cc=wangbinghui@hisilicon.com \
--cc=wanghu17@hisilicon.com \
--cc=xuejiancheng@hisilicon.com \
--cc=xuyiping@hisilicon.com \
--cc=xuyoujun4@huawei.com \
--cc=yamada.masahiro@socionext.com \
--cc=yudongbin@hisilicon.com \
--cc=zangleigang@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).