linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v7 00/12] Multiple fixes in PCIe qcom driver
@ 2020-06-15 21:05 Ansuel Smith
  2020-06-15 21:05 ` [PATCH v7 01/12] PCI: qcom: Add missing ipq806x clocks in PCIe driver Ansuel Smith
                   ` (14 more replies)
  0 siblings, 15 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:05 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Andy Gross, Bjorn Andersson,
	Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

This contains multiple fix for PCIe qcom driver.
Some optional reset and clocks were missing.
Fix a problem with no PARF programming that cause kernel lock on load.
Add support to force gen 1 speed if needed. (due to hardware limitation)
Add ipq8064 rev 2 support that use a different tx termination offset.

v7:
* Rework GEN1 patch

v6:
* Replace custom define
* Move define not used in 07 to 08

v5:
* Split PCI: qcom: Add ipq8064 rev2 variant and set tx term offset

v4:
* Fix grammar error across all patch subject
* Use bulk api for clks
* Program PARF only in ipq8064 SoC
* Program tx term only in ipq8064 SoC
* Drop configurable tx-dempth rx-eq
* Make added clk optional

v3:
* Fix check reported by checkpatch --strict
* Rename force_gen1 to gen

v2:
* Drop iATU programming (already done in pcie init)
* Use max-link-speed instead of force-gen1 custom definition
* Drop MRRS to 256B (Can't find a realy reason why this was suggested)
* Introduce a new variant for different revision of ipq8064

Abhishek Sahu (1):
  PCI: qcom: Change duplicate PCI reset to phy reset

Ansuel Smith (10):
  PCI: qcom: Add missing ipq806x clocks in PCIe driver
  dt-bindings: PCI: qcom: Add missing clks
  PCI: qcom: Add missing reset for ipq806x
  dt-bindings: PCI: qcom: Add ext reset
  PCI: qcom: Use bulk clk api and assert on error
  PCI: qcom: Define some PARF params needed for ipq8064 SoC
  PCI: qcom: Add support for tx term offset for rev 2.1.0
  PCI: qcom: Add ipq8064 rev2 variant
  dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant
  PCI: qcom: Replace define with standard value

Sham Muthayyan (1):
  PCI: qcom: Support pci speed set for ipq806x

 .../devicetree/bindings/pci/qcom,pcie.txt     |  15 +-
 drivers/pci/controller/dwc/pcie-qcom.c        | 186 +++++++++++-------
 2 files changed, 128 insertions(+), 73 deletions(-)

-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 01/12] PCI: qcom: Add missing ipq806x clocks in PCIe driver
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
@ 2020-06-15 21:05 ` Ansuel Smith
  2020-06-15 21:05 ` [PATCH v7 02/12] dt-bindings: PCI: qcom: Add missing clks Ansuel Smith
                   ` (13 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:05 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Sham Muthayyan, Rob Herring,
	Andy Gross, Bjorn Andersson, Bjorn Helgaas, Mark Rutland,
	Stanimir Varbanov, Lorenzo Pieralisi, Andrew Murray,
	Philipp Zabel, linux-arm-msm, linux-pci, devicetree,
	linux-kernel

Aux and Ref clk are missing in PCIe qcom driver. Add support for this
optional clks for ipq8064/apq8064 SoC.

Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 38 ++++++++++++++++++++++----
 1 file changed, 33 insertions(+), 5 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 5ea527a6bd9f..4bf93ab8c7a7 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -88,6 +88,8 @@ struct qcom_pcie_resources_2_1_0 {
 	struct clk *iface_clk;
 	struct clk *core_clk;
 	struct clk *phy_clk;
+	struct clk *aux_clk;
+	struct clk *ref_clk;
 	struct reset_control *pci_reset;
 	struct reset_control *axi_reset;
 	struct reset_control *ahb_reset;
@@ -246,6 +248,14 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
 	if (IS_ERR(res->phy_clk))
 		return PTR_ERR(res->phy_clk);
 
+	res->aux_clk = devm_clk_get_optional(dev, "aux");
+	if (IS_ERR(res->aux_clk))
+		return PTR_ERR(res->aux_clk);
+
+	res->ref_clk = devm_clk_get_optional(dev, "ref");
+	if (IS_ERR(res->ref_clk))
+		return PTR_ERR(res->ref_clk);
+
 	res->pci_reset = devm_reset_control_get_exclusive(dev, "pci");
 	if (IS_ERR(res->pci_reset))
 		return PTR_ERR(res->pci_reset);
@@ -278,6 +288,8 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
 	clk_disable_unprepare(res->iface_clk);
 	clk_disable_unprepare(res->core_clk);
 	clk_disable_unprepare(res->phy_clk);
+	clk_disable_unprepare(res->aux_clk);
+	clk_disable_unprepare(res->ref_clk);
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
 }
 
@@ -307,16 +319,28 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 		goto err_assert_ahb;
 	}
 
+	ret = clk_prepare_enable(res->core_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable core clock\n");
+		goto err_clk_core;
+	}
+
 	ret = clk_prepare_enable(res->phy_clk);
 	if (ret) {
 		dev_err(dev, "cannot prepare/enable phy clock\n");
 		goto err_clk_phy;
 	}
 
-	ret = clk_prepare_enable(res->core_clk);
+	ret = clk_prepare_enable(res->aux_clk);
 	if (ret) {
-		dev_err(dev, "cannot prepare/enable core clock\n");
-		goto err_clk_core;
+		dev_err(dev, "cannot prepare/enable aux clock\n");
+		goto err_clk_aux;
+	}
+
+	ret = clk_prepare_enable(res->ref_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable ref clock\n");
+		goto err_clk_ref;
 	}
 
 	ret = reset_control_deassert(res->ahb_reset);
@@ -372,10 +396,14 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 	return 0;
 
 err_deassert_ahb:
-	clk_disable_unprepare(res->core_clk);
-err_clk_core:
+	clk_disable_unprepare(res->ref_clk);
+err_clk_ref:
+	clk_disable_unprepare(res->aux_clk);
+err_clk_aux:
 	clk_disable_unprepare(res->phy_clk);
 err_clk_phy:
+	clk_disable_unprepare(res->core_clk);
+err_clk_core:
 	clk_disable_unprepare(res->iface_clk);
 err_assert_ahb:
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 02/12] dt-bindings: PCI: qcom: Add missing clks
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
  2020-06-15 21:05 ` [PATCH v7 01/12] PCI: qcom: Add missing ipq806x clocks in PCIe driver Ansuel Smith
@ 2020-06-15 21:05 ` Ansuel Smith
  2020-06-15 21:05 ` [PATCH v7 03/12] PCI: qcom: Change duplicate PCI reset to phy reset Ansuel Smith
                   ` (12 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:05 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Rob Herring, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Document missing clks used in ipq8064 SoC.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/pci/qcom,pcie.txt | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
index 981b4de12807..becdbdc0fffa 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
@@ -90,6 +90,8 @@
 	Definition: Should contain the following entries
 			- "core"	Clocks the pcie hw block
 			- "phy"		Clocks the pcie PHY block
+			- "aux" 	Clocks the pcie AUX block
+			- "ref" 	Clocks the pcie ref block
 - clock-names:
 	Usage: required for apq8084/ipq4019
 	Value type: <stringlist>
@@ -277,8 +279,10 @@
 				<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 		clocks = <&gcc PCIE_A_CLK>,
 			 <&gcc PCIE_H_CLK>,
-			 <&gcc PCIE_PHY_CLK>;
-		clock-names = "core", "iface", "phy";
+			 <&gcc PCIE_PHY_CLK>,
+			 <&gcc PCIE_AUX_CLK>,
+			 <&gcc PCIE_ALT_REF_CLK>;
+		clock-names = "core", "iface", "phy", "aux", "ref";
 		resets = <&gcc PCIE_ACLK_RESET>,
 			 <&gcc PCIE_HCLK_RESET>,
 			 <&gcc PCIE_POR_RESET>,
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 03/12] PCI: qcom: Change duplicate PCI reset to phy reset
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
  2020-06-15 21:05 ` [PATCH v7 01/12] PCI: qcom: Add missing ipq806x clocks in PCIe driver Ansuel Smith
  2020-06-15 21:05 ` [PATCH v7 02/12] dt-bindings: PCI: qcom: Add missing clks Ansuel Smith
@ 2020-06-15 21:05 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 04/12] PCI: qcom: Add missing reset for ipq806x Ansuel Smith
                   ` (11 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:05 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Abhishek Sahu, Ansuel Smith, Rob Herring, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

From: Abhishek Sahu <absahu@codeaurora.org>

The deinit issues reset_control_assert for PCI twice and does not contain
phy reset.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 4bf93ab8c7a7..4512c2c5f61c 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -280,14 +280,14 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
 {
 	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
 
+	clk_disable_unprepare(res->phy_clk);
 	reset_control_assert(res->pci_reset);
 	reset_control_assert(res->axi_reset);
 	reset_control_assert(res->ahb_reset);
 	reset_control_assert(res->por_reset);
-	reset_control_assert(res->pci_reset);
+	reset_control_assert(res->phy_reset);
 	clk_disable_unprepare(res->iface_clk);
 	clk_disable_unprepare(res->core_clk);
-	clk_disable_unprepare(res->phy_clk);
 	clk_disable_unprepare(res->aux_clk);
 	clk_disable_unprepare(res->ref_clk);
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
@@ -325,12 +325,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 		goto err_clk_core;
 	}
 
-	ret = clk_prepare_enable(res->phy_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable phy clock\n");
-		goto err_clk_phy;
-	}
-
 	ret = clk_prepare_enable(res->aux_clk);
 	if (ret) {
 		dev_err(dev, "cannot prepare/enable aux clock\n");
@@ -383,6 +377,12 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 		return ret;
 	}
 
+	ret = clk_prepare_enable(res->phy_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable phy clock\n");
+		goto err_deassert_ahb;
+	}
+
 	/* wait for clock acquisition */
 	usleep_range(1000, 1500);
 
@@ -400,8 +400,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 err_clk_ref:
 	clk_disable_unprepare(res->aux_clk);
 err_clk_aux:
-	clk_disable_unprepare(res->phy_clk);
-err_clk_phy:
 	clk_disable_unprepare(res->core_clk);
 err_clk_core:
 	clk_disable_unprepare(res->iface_clk);
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 04/12] PCI: qcom: Add missing reset for ipq806x
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (2 preceding siblings ...)
  2020-06-15 21:05 ` [PATCH v7 03/12] PCI: qcom: Change duplicate PCI reset to phy reset Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 05/12] dt-bindings: PCI: qcom: Add ext reset Ansuel Smith
                   ` (10 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Sham Muthayyan, stable, Rob Herring,
	Philipp Zabel, Andy Gross, Bjorn Andersson, Bjorn Helgaas,
	Mark Rutland, Stanimir Varbanov, Lorenzo Pieralisi,
	Andrew Murray, linux-arm-msm, linux-pci, devicetree,
	linux-kernel

Add missing ext reset used by ipq8064 SoC in PCIe qcom driver.

Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 4512c2c5f61c..4dab5ef630cc 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -95,6 +95,7 @@ struct qcom_pcie_resources_2_1_0 {
 	struct reset_control *ahb_reset;
 	struct reset_control *por_reset;
 	struct reset_control *phy_reset;
+	struct reset_control *ext_reset;
 	struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY];
 };
 
@@ -272,6 +273,10 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
 	if (IS_ERR(res->por_reset))
 		return PTR_ERR(res->por_reset);
 
+	res->ext_reset = devm_reset_control_get_optional_exclusive(dev, "ext");
+	if (IS_ERR(res->ext_reset))
+		return PTR_ERR(res->ext_reset);
+
 	res->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
 	return PTR_ERR_OR_ZERO(res->phy_reset);
 }
@@ -285,6 +290,7 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
 	reset_control_assert(res->axi_reset);
 	reset_control_assert(res->ahb_reset);
 	reset_control_assert(res->por_reset);
+	reset_control_assert(res->ext_reset);
 	reset_control_assert(res->phy_reset);
 	clk_disable_unprepare(res->iface_clk);
 	clk_disable_unprepare(res->core_clk);
@@ -343,6 +349,12 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 		goto err_deassert_ahb;
 	}
 
+	ret = reset_control_deassert(res->ext_reset);
+	if (ret) {
+		dev_err(dev, "cannot deassert ext reset\n");
+		goto err_deassert_ahb;
+	}
+
 	/* enable PCIe clocks and resets */
 	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
 	val &= ~BIT(0);
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 05/12] dt-bindings: PCI: qcom: Add ext reset
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (3 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 04/12] PCI: qcom: Add missing reset for ipq806x Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 06/12] PCI: qcom: Use bulk clk api and assert on error Ansuel Smith
                   ` (9 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Rob Herring, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Document ext reset used in ipq8064 SoC by qcom PCIe driver.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/pci/qcom,pcie.txt | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
index becdbdc0fffa..6efcef040741 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
@@ -179,6 +179,7 @@
 			- "pwr"			PWR reset
 			- "ahb"			AHB reset
 			- "phy_ahb"		PHY AHB reset
+			- "ext"			EXT reset
 
 - reset-names:
 	Usage: required for ipq8074
@@ -287,8 +288,9 @@
 			 <&gcc PCIE_HCLK_RESET>,
 			 <&gcc PCIE_POR_RESET>,
 			 <&gcc PCIE_PCI_RESET>,
-			 <&gcc PCIE_PHY_RESET>;
-		reset-names = "axi", "ahb", "por", "pci", "phy";
+			 <&gcc PCIE_PHY_RESET>,
+			 <&gcc PCIE_EXT_RESET>;
+		reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
 		pinctrl-0 = <&pcie_pins_default>;
 		pinctrl-names = "default";
 	};
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 06/12] PCI: qcom: Use bulk clk api and assert on error
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (4 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 05/12] dt-bindings: PCI: qcom: Add ext reset Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 07/12] PCI: qcom: Define some PARF params needed for ipq8064 SoC Ansuel Smith
                   ` (8 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Rob Herring, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Rework 2.1.0 revision to use bulk clk api and fix missing assert on
reset_control_deassert error.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 131 +++++++++----------------
 1 file changed, 46 insertions(+), 85 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 4dab5ef630cc..f2ea1ab6f584 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -84,12 +84,9 @@
 #define DEVICE_TYPE_RC				0x4
 
 #define QCOM_PCIE_2_1_0_MAX_SUPPLY	3
+#define QCOM_PCIE_2_1_0_MAX_CLOCKS	5
 struct qcom_pcie_resources_2_1_0 {
-	struct clk *iface_clk;
-	struct clk *core_clk;
-	struct clk *phy_clk;
-	struct clk *aux_clk;
-	struct clk *ref_clk;
+	struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
 	struct reset_control *pci_reset;
 	struct reset_control *axi_reset;
 	struct reset_control *ahb_reset;
@@ -237,25 +234,21 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
 	if (ret)
 		return ret;
 
-	res->iface_clk = devm_clk_get(dev, "iface");
-	if (IS_ERR(res->iface_clk))
-		return PTR_ERR(res->iface_clk);
-
-	res->core_clk = devm_clk_get(dev, "core");
-	if (IS_ERR(res->core_clk))
-		return PTR_ERR(res->core_clk);
-
-	res->phy_clk = devm_clk_get(dev, "phy");
-	if (IS_ERR(res->phy_clk))
-		return PTR_ERR(res->phy_clk);
+	res->clks[0].id = "iface";
+	res->clks[1].id = "core";
+	res->clks[2].id = "phy";
+	res->clks[3].id = "aux";
+	res->clks[4].id = "ref";
 
-	res->aux_clk = devm_clk_get_optional(dev, "aux");
-	if (IS_ERR(res->aux_clk))
-		return PTR_ERR(res->aux_clk);
+	/* iface, core, phy are required */
+	ret = devm_clk_bulk_get(dev, 3, res->clks);
+	if (ret < 0)
+		return ret;
 
-	res->ref_clk = devm_clk_get_optional(dev, "ref");
-	if (IS_ERR(res->ref_clk))
-		return PTR_ERR(res->ref_clk);
+	/* aux, ref are optional */
+	ret = devm_clk_bulk_get_optional(dev, 2, res->clks + 3);
+	if (ret < 0)
+		return ret;
 
 	res->pci_reset = devm_reset_control_get_exclusive(dev, "pci");
 	if (IS_ERR(res->pci_reset))
@@ -285,17 +278,13 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
 {
 	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
 
-	clk_disable_unprepare(res->phy_clk);
+	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
 	reset_control_assert(res->pci_reset);
 	reset_control_assert(res->axi_reset);
 	reset_control_assert(res->ahb_reset);
 	reset_control_assert(res->por_reset);
 	reset_control_assert(res->ext_reset);
 	reset_control_assert(res->phy_reset);
-	clk_disable_unprepare(res->iface_clk);
-	clk_disable_unprepare(res->core_clk);
-	clk_disable_unprepare(res->aux_clk);
-	clk_disable_unprepare(res->ref_clk);
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
 }
 
@@ -313,36 +302,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 		return ret;
 	}
 
-	ret = reset_control_assert(res->ahb_reset);
-	if (ret) {
-		dev_err(dev, "cannot assert ahb reset\n");
-		goto err_assert_ahb;
-	}
-
-	ret = clk_prepare_enable(res->iface_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable iface clock\n");
-		goto err_assert_ahb;
-	}
-
-	ret = clk_prepare_enable(res->core_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable core clock\n");
-		goto err_clk_core;
-	}
-
-	ret = clk_prepare_enable(res->aux_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable aux clock\n");
-		goto err_clk_aux;
-	}
-
-	ret = clk_prepare_enable(res->ref_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable ref clock\n");
-		goto err_clk_ref;
-	}
-
 	ret = reset_control_deassert(res->ahb_reset);
 	if (ret) {
 		dev_err(dev, "cannot deassert ahb reset\n");
@@ -352,48 +311,46 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 	ret = reset_control_deassert(res->ext_reset);
 	if (ret) {
 		dev_err(dev, "cannot deassert ext reset\n");
-		goto err_deassert_ahb;
+		goto err_deassert_ext;
 	}
 
-	/* enable PCIe clocks and resets */
-	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
-	val &= ~BIT(0);
-	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
-
-	/* enable external reference clock */
-	val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK);
-	val |= BIT(16);
-	writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK);
-
 	ret = reset_control_deassert(res->phy_reset);
 	if (ret) {
 		dev_err(dev, "cannot deassert phy reset\n");
-		return ret;
+		goto err_deassert_phy;
 	}
 
 	ret = reset_control_deassert(res->pci_reset);
 	if (ret) {
 		dev_err(dev, "cannot deassert pci reset\n");
-		return ret;
+		goto err_deassert_pci;
 	}
 
 	ret = reset_control_deassert(res->por_reset);
 	if (ret) {
 		dev_err(dev, "cannot deassert por reset\n");
-		return ret;
+		goto err_deassert_por;
 	}
 
 	ret = reset_control_deassert(res->axi_reset);
 	if (ret) {
 		dev_err(dev, "cannot deassert axi reset\n");
-		return ret;
+		goto err_deassert_axi;
 	}
 
-	ret = clk_prepare_enable(res->phy_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable phy clock\n");
-		goto err_deassert_ahb;
-	}
+	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	if (ret)
+		goto err_clks;
+
+	/* enable PCIe clocks and resets */
+	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
+	val &= ~BIT(0);
+	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+
+	/* enable external reference clock */
+	val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK);
+	val |= BIT(16);
+	writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK);
 
 	/* wait for clock acquisition */
 	usleep_range(1000, 1500);
@@ -407,15 +364,19 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 
 	return 0;
 
+err_clks:
+	reset_control_assert(res->axi_reset);
+err_deassert_axi:
+	reset_control_assert(res->por_reset);
+err_deassert_por:
+	reset_control_assert(res->pci_reset);
+err_deassert_pci:
+	reset_control_assert(res->phy_reset);
+err_deassert_phy:
+	reset_control_assert(res->ext_reset);
+err_deassert_ext:
+	reset_control_assert(res->ahb_reset);
 err_deassert_ahb:
-	clk_disable_unprepare(res->ref_clk);
-err_clk_ref:
-	clk_disable_unprepare(res->aux_clk);
-err_clk_aux:
-	clk_disable_unprepare(res->core_clk);
-err_clk_core:
-	clk_disable_unprepare(res->iface_clk);
-err_assert_ahb:
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
 
 	return ret;
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 07/12] PCI: qcom: Define some PARF params needed for ipq8064 SoC
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (5 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 06/12] PCI: qcom: Use bulk clk api and assert on error Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 08/12] PCI: qcom: Add support for tx term offset for rev 2.1.0 Ansuel Smith
                   ` (7 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, stable, Rob Herring, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Set some specific value for Tx De-Emphasis, Tx Swing and Rx equalization
needed on some ipq8064 based device (Netgear R7800 for example). Without
this the system locks on kernel load.

Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index f2ea1ab6f584..85313493d51b 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -77,6 +77,18 @@
 #define DBI_RO_WR_EN				1
 
 #define PERST_DELAY_US				1000
+/* PARF registers */
+#define PCIE20_PARF_PCS_DEEMPH			0x34
+#define PCS_DEEMPH_TX_DEEMPH_GEN1(x)		((x) << 16)
+#define PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(x)	((x) << 8)
+#define PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(x)	((x) << 0)
+
+#define PCIE20_PARF_PCS_SWING			0x38
+#define PCS_SWING_TX_SWING_FULL(x)		((x) << 8)
+#define PCS_SWING_TX_SWING_LOW(x)		((x) << 0)
+
+#define PCIE20_PARF_CONFIG_BITS		0x50
+#define PHY_RX0_EQ(x)				((x) << 24)
 
 #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE	0x358
 #define SLV_ADDR_SPACE_SZ			0x10000000
@@ -293,6 +305,7 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
+	struct device_node *node = dev->of_node;
 	u32 val;
 	int ret;
 
@@ -347,6 +360,17 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 	val &= ~BIT(0);
 	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
 
+	if (of_device_is_compatible(node, "qcom,pcie-ipq8064")) {
+		writel(PCS_DEEMPH_TX_DEEMPH_GEN1(24) |
+			       PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(24) |
+			       PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(34),
+		       pcie->parf + PCIE20_PARF_PCS_DEEMPH);
+		writel(PCS_SWING_TX_SWING_FULL(120) |
+			       PCS_SWING_TX_SWING_LOW(120),
+		       pcie->parf + PCIE20_PARF_PCS_SWING);
+		writel(PHY_RX0_EQ(4), pcie->parf + PCIE20_PARF_CONFIG_BITS);
+	}
+
 	/* enable external reference clock */
 	val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK);
 	val |= BIT(16);
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 08/12] PCI: qcom: Add support for tx term offset for rev 2.1.0
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (6 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 07/12] PCI: qcom: Define some PARF params needed for ipq8064 SoC Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 09/12] PCI: qcom: Add ipq8064 rev2 variant Ansuel Smith
                   ` (6 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Sham Muthayyan, stable, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Add tx term offset support to pcie qcom driver need in some revision of
the ipq806x SoC. Ipq8064 needs tx term offset set to 7.

Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v4.5+
---
 drivers/pci/controller/dwc/pcie-qcom.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 85313493d51b..2cd6d1456210 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -45,7 +45,13 @@
 #define PCIE_CAP_CPL_TIMEOUT_DISABLE		0x10
 
 #define PCIE20_PARF_PHY_CTRL			0x40
+#define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK	GENMASK(20, 16)
+#define PHY_CTRL_PHY_TX0_TERM_OFFSET(x)		((x) << 16)
+
 #define PCIE20_PARF_PHY_REFCLK			0x4C
+#define PHY_REFCLK_SSP_EN			BIT(16)
+#define PHY_REFCLK_USE_PAD			BIT(12)
+
 #define PCIE20_PARF_DBI_BASE_ADDR		0x168
 #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE		0x16C
 #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL	0x174
@@ -371,9 +377,18 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 		writel(PHY_RX0_EQ(4), pcie->parf + PCIE20_PARF_CONFIG_BITS);
 	}
 
+	if (of_device_is_compatible(node, "qcom,pcie-ipq8064")) {
+		/* set TX termination offset */
+		val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
+		val &= ~PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK;
+		val |= PHY_CTRL_PHY_TX0_TERM_OFFSET(7);
+		writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+	}
+
 	/* enable external reference clock */
 	val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK);
-	val |= BIT(16);
+	val &= ~PHY_REFCLK_USE_PAD;
+	val |= PHY_REFCLK_SSP_EN;
 	writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK);
 
 	/* wait for clock acquisition */
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 09/12] PCI: qcom: Add ipq8064 rev2 variant
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (7 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 08/12] PCI: qcom: Add support for tx term offset for rev 2.1.0 Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 10/12] dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant Ansuel Smith
                   ` (5 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Andy Gross, Bjorn Andersson,
	Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Ipq8064-v2 have tx term offset set to 0. Introduce this variant to permit
different offset based on the revision.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 2cd6d1456210..259b627bf890 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -366,7 +366,8 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 	val &= ~BIT(0);
 	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
 
-	if (of_device_is_compatible(node, "qcom,pcie-ipq8064")) {
+	if (of_device_is_compatible(node, "qcom,pcie-ipq8064") ||
+	    of_device_is_compatible(node, "qcom,pcie-ipq8064-v2")) {
 		writel(PCS_DEEMPH_TX_DEEMPH_GEN1(24) |
 			       PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(24) |
 			       PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(34),
@@ -1464,6 +1465,7 @@ static int qcom_pcie_probe(struct platform_device *pdev)
 static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-apq8084", .data = &ops_1_0_0 },
 	{ .compatible = "qcom,pcie-ipq8064", .data = &ops_2_1_0 },
+	{ .compatible = "qcom,pcie-ipq8064-v2", .data = &ops_2_1_0 },
 	{ .compatible = "qcom,pcie-apq8064", .data = &ops_2_1_0 },
 	{ .compatible = "qcom,pcie-msm8996", .data = &ops_2_3_2 },
 	{ .compatible = "qcom,pcie-ipq8074", .data = &ops_2_3_3 },
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 10/12] dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (8 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 09/12] PCI: qcom: Add ipq8064 rev2 variant Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 11/12] PCI: qcom: Support pci speed set for ipq806x Ansuel Smith
                   ` (4 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Rob Herring, Andy Gross,
	Bjorn Andersson, Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Document qcom,pcie-ipq8064-v2 needed to use different phy_tx0_term_offset.
In ipq8064 phy_tx0_term_offset is 7. In ipq8064 v2 other SoC it's set to 0
by default.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/pci/qcom,pcie.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
index 6efcef040741..02bc81bb8b2d 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
@@ -5,6 +5,7 @@
 	Value type: <stringlist>
 	Definition: Value should contain
 			- "qcom,pcie-ipq8064" for ipq8064
+			- "qcom,pcie-ipq8064-v2" for ipq8064 rev 2 or ipq8065
 			- "qcom,pcie-apq8064" for apq8064
 			- "qcom,pcie-apq8084" for apq8084
 			- "qcom,pcie-msm8996" for msm8996 or apq8096
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 11/12] PCI: qcom: Support pci speed set for ipq806x
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (9 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 10/12] dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-15 21:06 ` [PATCH v7 12/12] PCI: qcom: Replace define with standard value Ansuel Smith
                   ` (3 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Sham Muthayyan, Ansuel Smith, Rob Herring,
	Andy Gross, Bjorn Andersson, Bjorn Helgaas, Mark Rutland,
	Stanimir Varbanov, Lorenzo Pieralisi, Andrew Murray,
	Philipp Zabel, linux-arm-msm, linux-pci, devicetree,
	linux-kernel

From: Sham Muthayyan <smuthayy@codeaurora.org>

Some SoC based on ipq8064/5 needs to be limited to pci GEN1 speed due to
some hardware limitations. Add support for speed setting defined by the
max-link-speed binding. If not defined the max speed is set to GEN2 by
default.

Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 259b627bf890..c40921589122 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -27,6 +27,7 @@
 #include <linux/slab.h>
 #include <linux/types.h>
 
+#include "../../pci.h"
 #include "pcie-designware.h"
 
 #define PCIE20_PARF_SYS_CTRL			0x00
@@ -99,6 +100,8 @@
 #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE	0x358
 #define SLV_ADDR_SPACE_SZ			0x10000000
 
+#define PCIE20_LNK_CONTROL2_LINK_STATUS2	0xa0
+
 #define DEVICE_TYPE_RC				0x4
 
 #define QCOM_PCIE_2_1_0_MAX_SUPPLY	3
@@ -195,6 +198,7 @@ struct qcom_pcie {
 	struct phy *phy;
 	struct gpio_desc *reset;
 	const struct qcom_pcie_ops *ops;
+	int gen;
 };
 
 #define to_qcom_pcie(x)		dev_get_drvdata((x)->dev)
@@ -395,6 +399,11 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 	/* wait for clock acquisition */
 	usleep_range(1000, 1500);
 
+	if (pcie->gen == 1) {
+		val = readl(pci->dbi_base + PCIE20_LNK_CONTROL2_LINK_STATUS2);
+		val |= PCI_EXP_LNKSTA_CLS_2_5GB;
+		writel(val, pci->dbi_base + PCIE20_LNK_CONTROL2_LINK_STATUS2);
+	}
 
 	/* Set the Max TLP size to 2K, instead of using default of 4K */
 	writel(CFG_REMOTE_RD_REQ_BRIDGE_SIZE_2K,
@@ -1397,6 +1406,10 @@ static int qcom_pcie_probe(struct platform_device *pdev)
 		goto err_pm_runtime_put;
 	}
 
+	pcie->gen = of_pci_get_max_link_speed(pdev->dev.of_node);
+	if (pcie->gen < 0)
+		pcie->gen = 2;
+
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "parf");
 	pcie->parf = devm_ioremap_resource(dev, res);
 	if (IS_ERR(pcie->parf)) {
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v7 12/12] PCI: qcom: Replace define with standard value
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (10 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 11/12] PCI: qcom: Support pci speed set for ipq806x Ansuel Smith
@ 2020-06-15 21:06 ` Ansuel Smith
  2020-06-25 23:37 ` [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Stanimir Varbanov
                   ` (2 subsequent siblings)
  14 siblings, 0 replies; 17+ messages in thread
From: Ansuel Smith @ 2020-06-15 21:06 UTC (permalink / raw)
  To: Rob Herring
  Cc: Vinod Koul, Ansuel Smith, Andy Gross, Bjorn Andersson,
	Bjorn Helgaas, Mark Rutland, Stanimir Varbanov,
	Lorenzo Pieralisi, Andrew Murray, Philipp Zabel, linux-arm-msm,
	linux-pci, devicetree, linux-kernel

Lots of define are actually already defined in pci_regs.h, directly use
the standard defines.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 15 +++++----------
 1 file changed, 5 insertions(+), 10 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index c40921589122..a23d3d886479 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -40,11 +40,6 @@
 #define L23_CLK_RMV_DIS				BIT(2)
 #define L1_CLK_RMV_DIS				BIT(1)
 
-#define PCIE20_COMMAND_STATUS			0x04
-#define CMD_BME_VAL				0x4
-#define PCIE20_DEVICE_CONTROL2_STATUS2		0x98
-#define PCIE_CAP_CPL_TIMEOUT_DISABLE		0x10
-
 #define PCIE20_PARF_PHY_CTRL			0x40
 #define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK	GENMASK(20, 16)
 #define PHY_CTRL_PHY_TX0_TERM_OFFSET(x)		((x) << 16)
@@ -73,8 +68,8 @@
 #define CFG_BRIDGE_SB_INIT			BIT(0)
 
 #define PCIE20_CAP				0x70
-#define PCIE20_CAP_LINK_CAPABILITIES		(PCIE20_CAP + 0xC)
-#define PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT	(BIT(10) | BIT(11))
+#define PCIE20_DEVICE_CONTROL2_STATUS2		(PCIE20_CAP + PCI_EXP_DEVCTL2)
+#define PCIE20_CAP_LINK_CAPABILITIES		(PCIE20_CAP + PCI_EXP_LNKCAP)
 #define PCIE20_CAP_LINK_1			(PCIE20_CAP + 0x14)
 #define PCIE_CAP_LINK1_VAL			0x2FD7F
 
@@ -1095,15 +1090,15 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
 		pcie->parf + PCIE20_PARF_SYS_CTRL);
 	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
 
-	writel(CMD_BME_VAL, pci->dbi_base + PCIE20_COMMAND_STATUS);
+	writel(PCI_COMMAND_MASTER, pci->dbi_base + PCI_COMMAND);
 	writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG);
 	writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + PCIE20_CAP_LINK_1);
 
 	val = readl(pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES);
-	val &= ~PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT;
+	val &= ~PCI_EXP_LNKCAP_ASPMS;
 	writel(val, pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES);
 
-	writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base +
+	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base +
 		PCIE20_DEVICE_CONTROL2_STATUS2);
 
 	return 0;
-- 
2.27.0.rc0


^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v7 00/12] Multiple fixes in PCIe qcom driver
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (11 preceding siblings ...)
  2020-06-15 21:06 ` [PATCH v7 12/12] PCI: qcom: Replace define with standard value Ansuel Smith
@ 2020-06-25 23:37 ` Stanimir Varbanov
  2020-07-07 14:05 ` Lorenzo Pieralisi
  2020-07-07 15:15 ` Lorenzo Pieralisi
  14 siblings, 0 replies; 17+ messages in thread
From: Stanimir Varbanov @ 2020-06-25 23:37 UTC (permalink / raw)
  To: Ansuel Smith, Rob Herring
  Cc: Vinod Koul, Andy Gross, Bjorn Andersson, Bjorn Helgaas,
	Mark Rutland, Lorenzo Pieralisi, Andrew Murray, Philipp Zabel,
	linux-arm-msm, linux-pci, devicetree, linux-kernel

Hi Ansuel,

Thank you for the patience.

On 6/16/20 12:05 AM, Ansuel Smith wrote:
> This contains multiple fix for PCIe qcom driver.
> Some optional reset and clocks were missing.
> Fix a problem with no PARF programming that cause kernel lock on load.
> Add support to force gen 1 speed if needed. (due to hardware limitation)
> Add ipq8064 rev 2 support that use a different tx termination offset.
> 
> v7:
> * Rework GEN1 patch
> 
> v6:
> * Replace custom define
> * Move define not used in 07 to 08
> 
> v5:
> * Split PCI: qcom: Add ipq8064 rev2 variant and set tx term offset
> 
> v4:
> * Fix grammar error across all patch subject
> * Use bulk api for clks
> * Program PARF only in ipq8064 SoC
> * Program tx term only in ipq8064 SoC
> * Drop configurable tx-dempth rx-eq
> * Make added clk optional
> 
> v3:
> * Fix check reported by checkpatch --strict
> * Rename force_gen1 to gen
> 
> v2:
> * Drop iATU programming (already done in pcie init)
> * Use max-link-speed instead of force-gen1 custom definition
> * Drop MRRS to 256B (Can't find a realy reason why this was suggested)
> * Introduce a new variant for different revision of ipq8064
> 
> Abhishek Sahu (1):
>   PCI: qcom: Change duplicate PCI reset to phy reset
> 
> Ansuel Smith (10):
>   PCI: qcom: Add missing ipq806x clocks in PCIe driver
>   dt-bindings: PCI: qcom: Add missing clks
>   PCI: qcom: Add missing reset for ipq806x
>   dt-bindings: PCI: qcom: Add ext reset
>   PCI: qcom: Use bulk clk api and assert on error
>   PCI: qcom: Define some PARF params needed for ipq8064 SoC
>   PCI: qcom: Add support for tx term offset for rev 2.1.0
>   PCI: qcom: Add ipq8064 rev2 variant
>   dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant
>   PCI: qcom: Replace define with standard value
> 
> Sham Muthayyan (1):
>   PCI: qcom: Support pci speed set for ipq806x
> 
>  .../devicetree/bindings/pci/qcom,pcie.txt     |  15 +-
>  drivers/pci/controller/dwc/pcie-qcom.c        | 186 +++++++++++-------
>  2 files changed, 128 insertions(+), 73 deletions(-)
> 

For the whole set:

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>

-- 
regards,
Stan

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v7 00/12] Multiple fixes in PCIe qcom driver
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (12 preceding siblings ...)
  2020-06-25 23:37 ` [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Stanimir Varbanov
@ 2020-07-07 14:05 ` Lorenzo Pieralisi
  2020-07-07 14:57   ` Stanimir Varbanov
  2020-07-07 15:15 ` Lorenzo Pieralisi
  14 siblings, 1 reply; 17+ messages in thread
From: Lorenzo Pieralisi @ 2020-07-07 14:05 UTC (permalink / raw)
  To: Ansuel Smith
  Cc: Rob Herring, Vinod Koul, Andy Gross, Bjorn Andersson,
	Bjorn Helgaas, Mark Rutland, Stanimir Varbanov, Andrew Murray,
	Philipp Zabel, linux-arm-msm, linux-pci, devicetree,
	linux-kernel

On Mon, Jun 15, 2020 at 11:05:56PM +0200, Ansuel Smith wrote:
> This contains multiple fix for PCIe qcom driver.
> Some optional reset and clocks were missing.
> Fix a problem with no PARF programming that cause kernel lock on load.
> Add support to force gen 1 speed if needed. (due to hardware limitation)
> Add ipq8064 rev 2 support that use a different tx termination offset.
> 
> v7:
> * Rework GEN1 patch
> 
> v6:
> * Replace custom define
> * Move define not used in 07 to 08
> 
> v5:
> * Split PCI: qcom: Add ipq8064 rev2 variant and set tx term offset
> 
> v4:
> * Fix grammar error across all patch subject
> * Use bulk api for clks
> * Program PARF only in ipq8064 SoC
> * Program tx term only in ipq8064 SoC
> * Drop configurable tx-dempth rx-eq
> * Make added clk optional
> 
> v3:
> * Fix check reported by checkpatch --strict
> * Rename force_gen1 to gen
> 
> v2:
> * Drop iATU programming (already done in pcie init)
> * Use max-link-speed instead of force-gen1 custom definition
> * Drop MRRS to 256B (Can't find a realy reason why this was suggested)
> * Introduce a new variant for different revision of ipq8064
> 
> Abhishek Sahu (1):
>   PCI: qcom: Change duplicate PCI reset to phy reset
> 
> Ansuel Smith (10):
>   PCI: qcom: Add missing ipq806x clocks in PCIe driver
>   dt-bindings: PCI: qcom: Add missing clks
>   PCI: qcom: Add missing reset for ipq806x
>   dt-bindings: PCI: qcom: Add ext reset
>   PCI: qcom: Use bulk clk api and assert on error
>   PCI: qcom: Define some PARF params needed for ipq8064 SoC
>   PCI: qcom: Add support for tx term offset for rev 2.1.0
>   PCI: qcom: Add ipq8064 rev2 variant
>   dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant
>   PCI: qcom: Replace define with standard value
> 
> Sham Muthayyan (1):
>   PCI: qcom: Support pci speed set for ipq806x
> 
>  .../devicetree/bindings/pci/qcom,pcie.txt     |  15 +-
>  drivers/pci/controller/dwc/pcie-qcom.c        | 186 +++++++++++-------
>  2 files changed, 128 insertions(+), 73 deletions(-)

ACK missing on patches 8,9,12 please let me know how to proceed,
thanks.

Lorenzo

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v7 00/12] Multiple fixes in PCIe qcom driver
  2020-07-07 14:05 ` Lorenzo Pieralisi
@ 2020-07-07 14:57   ` Stanimir Varbanov
  0 siblings, 0 replies; 17+ messages in thread
From: Stanimir Varbanov @ 2020-07-07 14:57 UTC (permalink / raw)
  To: Lorenzo Pieralisi, Ansuel Smith
  Cc: Rob Herring, Vinod Koul, Andy Gross, Bjorn Andersson,
	Bjorn Helgaas, Mark Rutland, Andrew Murray, Philipp Zabel,
	linux-arm-msm, linux-pci, devicetree, linux-kernel

Hi Lorenzo,

On 7/7/20 5:05 PM, Lorenzo Pieralisi wrote:
> On Mon, Jun 15, 2020 at 11:05:56PM +0200, Ansuel Smith wrote:
>> This contains multiple fix for PCIe qcom driver.
>> Some optional reset and clocks were missing.
>> Fix a problem with no PARF programming that cause kernel lock on load.
>> Add support to force gen 1 speed if needed. (due to hardware limitation)
>> Add ipq8064 rev 2 support that use a different tx termination offset.
>>
>> v7:
>> * Rework GEN1 patch
>>
>> v6:
>> * Replace custom define
>> * Move define not used in 07 to 08
>>
>> v5:
>> * Split PCI: qcom: Add ipq8064 rev2 variant and set tx term offset
>>
>> v4:
>> * Fix grammar error across all patch subject
>> * Use bulk api for clks
>> * Program PARF only in ipq8064 SoC
>> * Program tx term only in ipq8064 SoC
>> * Drop configurable tx-dempth rx-eq
>> * Make added clk optional
>>
>> v3:
>> * Fix check reported by checkpatch --strict
>> * Rename force_gen1 to gen
>>
>> v2:
>> * Drop iATU programming (already done in pcie init)
>> * Use max-link-speed instead of force-gen1 custom definition
>> * Drop MRRS to 256B (Can't find a realy reason why this was suggested)
>> * Introduce a new variant for different revision of ipq8064
>>
>> Abhishek Sahu (1):
>>   PCI: qcom: Change duplicate PCI reset to phy reset
>>
>> Ansuel Smith (10):
>>   PCI: qcom: Add missing ipq806x clocks in PCIe driver
>>   dt-bindings: PCI: qcom: Add missing clks
>>   PCI: qcom: Add missing reset for ipq806x
>>   dt-bindings: PCI: qcom: Add ext reset
>>   PCI: qcom: Use bulk clk api and assert on error
>>   PCI: qcom: Define some PARF params needed for ipq8064 SoC
>>   PCI: qcom: Add support for tx term offset for rev 2.1.0
>>   PCI: qcom: Add ipq8064 rev2 variant
>>   dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant
>>   PCI: qcom: Replace define with standard value
>>
>> Sham Muthayyan (1):
>>   PCI: qcom: Support pci speed set for ipq806x
>>
>>  .../devicetree/bindings/pci/qcom,pcie.txt     |  15 +-
>>  drivers/pci/controller/dwc/pcie-qcom.c        | 186 +++++++++++-------
>>  2 files changed, 128 insertions(+), 73 deletions(-)
> 
> ACK missing on patches 8,9,12 please let me know how to proceed,
> thanks.

You could use my acked-by for them:

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>

> 
> Lorenzo
> 

-- 
regards,
Stan

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v7 00/12] Multiple fixes in PCIe qcom driver
  2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
                   ` (13 preceding siblings ...)
  2020-07-07 14:05 ` Lorenzo Pieralisi
@ 2020-07-07 15:15 ` Lorenzo Pieralisi
  14 siblings, 0 replies; 17+ messages in thread
From: Lorenzo Pieralisi @ 2020-07-07 15:15 UTC (permalink / raw)
  To: Ansuel Smith
  Cc: Rob Herring, Vinod Koul, Andy Gross, Bjorn Andersson,
	Bjorn Helgaas, Mark Rutland, Stanimir Varbanov, Andrew Murray,
	Philipp Zabel, linux-arm-msm, linux-pci, devicetree,
	linux-kernel

On Mon, Jun 15, 2020 at 11:05:56PM +0200, Ansuel Smith wrote:
> This contains multiple fix for PCIe qcom driver.
> Some optional reset and clocks were missing.
> Fix a problem with no PARF programming that cause kernel lock on load.
> Add support to force gen 1 speed if needed. (due to hardware limitation)
> Add ipq8064 rev 2 support that use a different tx termination offset.
> 
> v7:
> * Rework GEN1 patch
> 
> v6:
> * Replace custom define
> * Move define not used in 07 to 08
> 
> v5:
> * Split PCI: qcom: Add ipq8064 rev2 variant and set tx term offset
> 
> v4:
> * Fix grammar error across all patch subject
> * Use bulk api for clks
> * Program PARF only in ipq8064 SoC
> * Program tx term only in ipq8064 SoC
> * Drop configurable tx-dempth rx-eq
> * Make added clk optional
> 
> v3:
> * Fix check reported by checkpatch --strict
> * Rename force_gen1 to gen
> 
> v2:
> * Drop iATU programming (already done in pcie init)
> * Use max-link-speed instead of force-gen1 custom definition
> * Drop MRRS to 256B (Can't find a realy reason why this was suggested)
> * Introduce a new variant for different revision of ipq8064
> 
> Abhishek Sahu (1):
>   PCI: qcom: Change duplicate PCI reset to phy reset
> 
> Ansuel Smith (10):
>   PCI: qcom: Add missing ipq806x clocks in PCIe driver
>   dt-bindings: PCI: qcom: Add missing clks
>   PCI: qcom: Add missing reset for ipq806x
>   dt-bindings: PCI: qcom: Add ext reset
>   PCI: qcom: Use bulk clk api and assert on error
>   PCI: qcom: Define some PARF params needed for ipq8064 SoC
>   PCI: qcom: Add support for tx term offset for rev 2.1.0
>   PCI: qcom: Add ipq8064 rev2 variant
>   dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant
>   PCI: qcom: Replace define with standard value
> 
> Sham Muthayyan (1):
>   PCI: qcom: Support pci speed set for ipq806x
> 
>  .../devicetree/bindings/pci/qcom,pcie.txt     |  15 +-
>  drivers/pci/controller/dwc/pcie-qcom.c        | 186 +++++++++++-------
>  2 files changed, 128 insertions(+), 73 deletions(-)

Applied to pci/dwc for v5.9, thanks.

Lorenzo

^ permalink raw reply	[flat|nested] 17+ messages in thread

end of thread, other threads:[~2020-07-07 15:15 UTC | newest]

Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-15 21:05 [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Ansuel Smith
2020-06-15 21:05 ` [PATCH v7 01/12] PCI: qcom: Add missing ipq806x clocks in PCIe driver Ansuel Smith
2020-06-15 21:05 ` [PATCH v7 02/12] dt-bindings: PCI: qcom: Add missing clks Ansuel Smith
2020-06-15 21:05 ` [PATCH v7 03/12] PCI: qcom: Change duplicate PCI reset to phy reset Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 04/12] PCI: qcom: Add missing reset for ipq806x Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 05/12] dt-bindings: PCI: qcom: Add ext reset Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 06/12] PCI: qcom: Use bulk clk api and assert on error Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 07/12] PCI: qcom: Define some PARF params needed for ipq8064 SoC Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 08/12] PCI: qcom: Add support for tx term offset for rev 2.1.0 Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 09/12] PCI: qcom: Add ipq8064 rev2 variant Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 10/12] dt-bindings: PCI: qcom: Add ipq8064 rev 2 variant Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 11/12] PCI: qcom: Support pci speed set for ipq806x Ansuel Smith
2020-06-15 21:06 ` [PATCH v7 12/12] PCI: qcom: Replace define with standard value Ansuel Smith
2020-06-25 23:37 ` [PATCH v7 00/12] Multiple fixes in PCIe qcom driver Stanimir Varbanov
2020-07-07 14:05 ` Lorenzo Pieralisi
2020-07-07 14:57   ` Stanimir Varbanov
2020-07-07 15:15 ` Lorenzo Pieralisi

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).