* [PATCH v4 0/2] mfd: max597x: Add support for max597x
@ 2022-11-01 16:53 Naresh Solanki
2022-11-01 16:53 ` [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978 Naresh Solanki
2022-11-01 16:53 ` [PATCH v4 2/2] mfd: max597x: Add support " Naresh Solanki
0 siblings, 2 replies; 5+ messages in thread
From: Naresh Solanki @ 2022-11-01 16:53 UTC (permalink / raw)
To: linux-kernel, devicetree; +Cc: Naresh Solanki
max597x is multifunction device with hot swap controller, fault
protection & upto four indication leds.
max5978 has single hot swap controller whereas max5970 has two hot swap
controllers.
Changes in V4:
- Add NULL entry for of_device_id
- Memory allocation check
Changes in V3:
- Address code review comment
Changes in V2:
- Update depends in Kconfig.
Marcello Sylvester Bauer (1):
dt-bindings: mfd: Add bindings for MAX5970 and MAX5978
Patrick Rudolph (1):
mfd: max597x: Add support for MAX5970 and MAX5978
.../devicetree/bindings/mfd/max5970.yaml | 164 ++++++++++++++++++
drivers/mfd/Kconfig | 12 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/max597x.c | 92 ++++++++++
include/linux/mfd/max597x.h | 103 +++++++++++
5 files changed, 372 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/max5970.yaml
create mode 100644 drivers/mfd/max597x.c
create mode 100644 include/linux/mfd/max597x.h
base-commit: 6b780408be034213edfb5946889882cb29f8f159
--
2.37.3
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978
2022-11-01 16:53 [PATCH v4 0/2] mfd: max597x: Add support for max597x Naresh Solanki
@ 2022-11-01 16:53 ` Naresh Solanki
2022-11-02 2:26 ` Rob Herring
2022-11-02 17:19 ` Krzysztof Kozlowski
2022-11-01 16:53 ` [PATCH v4 2/2] mfd: max597x: Add support " Naresh Solanki
1 sibling, 2 replies; 5+ messages in thread
From: Naresh Solanki @ 2022-11-01 16:53 UTC (permalink / raw)
To: linux-kernel, devicetree, Lee Jones, Rob Herring,
Krzysztof Kozlowski, Patrick Rudolph
Cc: Marcello Sylvester Bauer, Naresh Solanki
From: Marcello Sylvester Bauer <sylv@sylv.io>
The MAX597x is a hot swap controller with configurable fault protection.
It also has 10bit ADC for current & voltage measurements.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
---
.../devicetree/bindings/mfd/max5970.yaml | 164 ++++++++++++++++++
1 file changed, 164 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/max5970.yaml
diff --git a/Documentation/devicetree/bindings/mfd/max5970.yaml b/Documentation/devicetree/bindings/mfd/max5970.yaml
new file mode 100644
index 000000000000..a0cc6a7543b5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max5970.yaml
@@ -0,0 +1,164 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/max5970.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Regulator driver for MAX5970 smart switch from Maxim Integrated.
+
+maintainers:
+ - Patrick Rudolph <patrick.rudolph@9elements.com>
+
+description: |
+ The smart switch provides no output regulation, but independent fault protection
+ and voltage and current sensing.
+ Programming is done through I2C bus.
+
+ Datasheets:
+ https://datasheets.maximintegrated.com/en/ds/MAX5970.pdf
+ https://datasheets.maximintegrated.com/en/ds/MAX5978.pdf
+
+properties:
+ compatible:
+ enum:
+ - maxim,max5970
+ - maxim,max5978
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ leds:
+ type: object
+ description:
+ Properties for single channel.
+
+ patternProperties:
+ "^led@[0-3]$":
+ $ref: /schemas/leds/common.yaml#
+ type: object
+
+ additionalProperties: true
+
+ vss1-supply:
+ description: Supply of the first channel.
+
+ "#io-channel-cells":
+ const: 1
+
+ regulators:
+ type: object
+ description:
+ Properties for single channel.
+
+ patternProperties:
+ "^(sw[0-1])$":
+ $ref: /schemas/regulator/regulator.yaml#
+ type: object
+
+ shunt-resistor-micro-ohms:
+ description: |
+ The value of curent sense resistor in microohms.
+ Must be specified for each channel.
+
+ additionalProperties: true
+
+required:
+ - compatible
+ - reg
+ - regulators
+ - vss1-supply
+
+allOf:
+ - $ref: /schemas/regulator/regulator.yaml#
+ - if:
+ properties:
+ compatible:
+ enum:
+ - maxim,max5970
+ then:
+ properties:
+ vss2-supply:
+ description: Supply of the second channel.
+
+ io-channels:
+ items:
+ - description: voltage first channel
+ - description: current first channel
+ - description: voltage second channel
+ - description: current second channel
+ description: |
+ Voltage and current for first and second channel.
+ required:
+ - vss2-supply
+
+ else:
+ properties:
+ io-channels:
+ items:
+ - description: voltage first channel
+ - description: current first channel
+ description: |
+ Voltage and current for first channel.
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ led@0 {
+ reg = <0>;
+ label = "led0";
+ default-state = "on";
+ };
+ led@1 {
+ reg = <1>;
+ label = "led1";
+ default-state = "on";
+ };
+ };
+ regulator@3a {
+ reg = <0x3a>;
+ vss1-supply = <&p3v3>;
+ compatible = "maxim,max5978";
+
+ regulators {
+ sw0_ref_0: SW0 {
+ regulator-compatible = "SW0";
+ shunt-resistor-micro-ohms = <12000>;
+ };
+ };
+ };
+ };
+
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ regulator@3a {
+ reg = <0x3a>;
+ vss1-supply = <&p3v3>;
+ vss2-supply = <&p5v>;
+ compatible = "maxim,max5970";
+
+ regulators {
+ sw0_ref_1: SW0 {
+ regulator-compatible = "SW0";
+ shunt-resistor-micro-ohms = <12000>;
+ };
+ sw1_ref_1: SW1 {
+ regulator-compatible = "SW1";
+ shunt-resistor-micro-ohms = <10000>;
+ };
+ };
+ };
+ };
+...
--
2.37.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v4 2/2] mfd: max597x: Add support for MAX5970 and MAX5978
2022-11-01 16:53 [PATCH v4 0/2] mfd: max597x: Add support for max597x Naresh Solanki
2022-11-01 16:53 ` [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978 Naresh Solanki
@ 2022-11-01 16:53 ` Naresh Solanki
1 sibling, 0 replies; 5+ messages in thread
From: Naresh Solanki @ 2022-11-01 16:53 UTC (permalink / raw)
To: linux-kernel, devicetree, Lee Jones
Cc: Patrick Rudolph, Marcello Sylvester Bauer, Naresh Solanki
From: Patrick Rudolph <patrick.rudolph@9elements.com>
Implement a regulator driver with IRQ support for fault management.
Written against documentation [1] and [2] and tested on real hardware.
Every channel has its own regulator supplies nammed 'vss1-supply' and
'vss2-supply'. The regulator supply is used to determine the output
voltage, as the smart switch provides no output regulation.
The driver requires the 'shunt-resistor-micro-ohms' property to be
present in Device Tree to properly calculate current related
values.
Datasheet links:
1: https://datasheets.maximintegrated.com/en/ds/MAX5970.pdf
2: https://datasheets.maximintegrated.com/en/ds/MAX5978.pdf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
---
drivers/mfd/Kconfig | 12 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/max597x.c | 92 ++++++++++++++++++++++++++++++++
include/linux/mfd/max597x.h | 103 ++++++++++++++++++++++++++++++++++++
4 files changed, 208 insertions(+)
create mode 100644 drivers/mfd/max597x.c
create mode 100644 include/linux/mfd/max597x.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8b93856de432..416fe7986b7b 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -253,6 +253,18 @@ config MFD_MADERA_SPI
Support for the Cirrus Logic Madera platform audio SoC
core functionality controlled via SPI.
+config MFD_MAX597X
+ tristate "Maxim 597x Power Switch and Monitor"
+ depends on I2C
+ depends on OF
+ select MFD_CORE
+ select REGMAP_I2C
+ help
+ This driver controls a Maxim 5970/5978 switch via I2C bus.
+ The MAX5970/5978 is a smart switch with no output regulation, but
+ fault protection and voltage and current monitoring capabilities.
+ Also it supports upto 4 indication LEDs.
+
config MFD_CS47L15
bool "Cirrus Logic CS47L15"
select PINCTRL_CS47L15
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 7ed3ef4a698c..819d711fa748 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -161,6 +161,7 @@ obj-$(CONFIG_MFD_DA9063) += da9063.o
obj-$(CONFIG_MFD_DA9150) += da9150-core.o
obj-$(CONFIG_MFD_MAX14577) += max14577.o
+obj-$(CONFIG_MFD_MAX597X) += max597x.o
obj-$(CONFIG_MFD_MAX77620) += max77620.o
obj-$(CONFIG_MFD_MAX77650) += max77650.o
obj-$(CONFIG_MFD_MAX77686) += max77686.o
diff --git a/drivers/mfd/max597x.c b/drivers/mfd/max597x.c
new file mode 100644
index 000000000000..2c64edb6b6dd
--- /dev/null
+++ b/drivers/mfd/max597x.c
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Maxim MAX5970/MAX5978 MFD Driver
+ *
+ * Copyright (c) 2022 9elements GmbH
+ *
+ * Author: Patrick Rudolph <patrick.rudolph@9elements.com>
+ */
+
+#include <linux/i2c.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/max597x.h>
+#include <linux/regmap.h>
+
+static const struct regmap_config max597x_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX_REGISTERS,
+};
+
+static const struct mfd_cell max597x_cells[] = {
+ { .name = "max597x-regulator", },
+ { .name = "max597x-iio", },
+ { .name = "max597x-led", },
+};
+
+static int max597x_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
+{
+ struct max597x_data *ddata;
+ enum max597x_chip_type chip = id->driver_data;
+
+ ddata = devm_kzalloc(&i2c->dev, sizeof(*ddata), GFP_KERNEL);
+ if (!ddata)
+ return -ENOMEM;
+
+ /* Initialize num of switch based on chip type for later use by regulator
+ * & iio cells
+ */
+ switch (chip) {
+ case MAX597x_TYPE_MAX5970:
+ ddata->num_switches = MAX5970_NUM_SWITCHES;
+ break;
+ case MAX597x_TYPE_MAX5978:
+ ddata->num_switches = MAX5978_NUM_SWITCHES;
+ break;
+ }
+
+ ddata->regmap = devm_regmap_init_i2c(i2c, &max597x_regmap_config);
+ if (IS_ERR(ddata->regmap)) {
+ dev_err(&i2c->dev, "Failed to initialise regmap");
+ return -EINVAL;
+ }
+
+ /* IRQ used by regulator cell */
+ ddata->irq = i2c->irq;
+ ddata->dev = &i2c->dev;
+ i2c_set_clientdata(i2c, ddata);
+
+ return devm_mfd_add_devices(ddata->dev, PLATFORM_DEVID_AUTO,
+ max597x_cells, ARRAY_SIZE(max597x_cells),
+ NULL, 0, NULL);
+}
+
+static const struct i2c_device_id max597x_table[] = {
+ { .name = "max5970", MAX597x_TYPE_MAX5970 },
+ { .name = "max5978", MAX597x_TYPE_MAX5978 },
+};
+
+MODULE_DEVICE_TABLE(i2c, max597x_table);
+
+static const struct of_device_id max597x_of_match[] = {
+ { .compatible = "maxim,max5970", .data = (void *)MAX597x_TYPE_MAX5970 },
+ { .compatible = "maxim,max5978", .data = (void *)MAX597x_TYPE_MAX5978 },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, max597x_of_match);
+
+static struct i2c_driver max597x_driver = {
+ .id_table = max597x_table,
+ .driver = {
+ .name = "max597x",
+ .of_match_table = of_match_ptr(max597x_of_match),
+ },
+ .probe = max597x_probe,
+};
+
+module_i2c_driver(max597x_driver);
+
+MODULE_AUTHOR("Patrick Rudolph <patrick.rudolph@9elements.com>");
+MODULE_DESCRIPTION("MAX597X Power Switch and Monitor");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/max597x.h b/include/linux/mfd/max597x.h
new file mode 100644
index 000000000000..f88a57f0e4f2
--- /dev/null
+++ b/include/linux/mfd/max597x.h
@@ -0,0 +1,103 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Maxim MAX5970/MAX5978 MFD Driver
+ *
+ * Copyright (c) 2022 9elements GmbH
+ *
+ * Author: Patrick Rudolph <patrick.rudolph@9elements.com>
+ */
+
+#ifndef MFD_MAX597X_H
+#define MFD_MAX597X_H
+
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+/* Number of switch based on chip variant */
+#define MAX5970_NUM_SWITCHES 2
+#define MAX5978_NUM_SWITCHES 1
+/* Both chip variant have 4 indication LEDs used by LED cell */
+#define MAX597X_NUM_LEDS 4
+
+enum max597x_chip_type {
+ MAX597x_TYPE_MAX5978 = 1,
+ MAX597x_TYPE_MAX5970,
+};
+
+#define MAX5970_REG_CURRENT_L(ch) (0x01 + (ch) * 4)
+#define MAX5970_REG_CURRENT_H(ch) (0x00 + (ch) * 4)
+#define MAX5970_REG_VOLTAGE_L(ch) (0x03 + (ch) * 4)
+#define MAX5970_REG_VOLTAGE_H(ch) (0x02 + (ch) * 4)
+#define MAX5970_REG_MON_RANGE 0x18
+#define MAX5970_MON_MASK 0x3
+#define MAX5970_MON(reg, ch) (((reg) >> ((ch) * 2)) & MAX5970_MON_MASK)
+#define MAX5970_MON_MAX_RANGE_UV 16000000
+
+#define MAX5970_REG_CH_UV_WARN_H(ch) (0x1A + (ch) * 10)
+#define MAX5970_REG_CH_UV_WARN_L(ch) (0x1B + (ch) * 10)
+#define MAX5970_REG_CH_UV_CRIT_H(ch) (0x1C + (ch) * 10)
+#define MAX5970_REG_CH_UV_CRIT_L(ch) (0x1D + (ch) * 10)
+#define MAX5970_REG_CH_OV_WARN_H(ch) (0x1E + (ch) * 10)
+#define MAX5970_REG_CH_OV_WARN_L(ch) (0x1F + (ch) * 10)
+#define MAX5970_REG_CH_OV_CRIT_H(ch) (0x20 + (ch) * 10)
+#define MAX5970_REG_CH_OV_CRIT_L(ch) (0x21 + (ch) * 10)
+
+#define MAX5970_VAL2REG_H(x) (((x) >> 2) & 0xFF)
+#define MAX5970_VAL2REG_L(x) ((x) & 0x3)
+
+#define MAX5970_REG_DAC_FAST(ch) (0x2E + (ch))
+
+#define MAX5970_FAST2SLOW_RATIO 200
+
+#define MAX5970_REG_STATUS0 0x31
+#define MAX5970_CB_IFAULTF(ch) (1 << (ch))
+#define MAX5970_CB_IFAULTS(ch) (1 << ((ch) + 4))
+
+#define MAX5970_REG_STATUS1 0x32
+#define STATUS1_PROT_MASK 0x3
+#define STATUS1_PROT(reg) \
+ (((reg) >> 6) & STATUS1_PROT_MASK)
+#define STATUS1_PROT_SHUTDOWN 0
+#define STATUS1_PROT_CLEAR_PG 1
+#define STATUS1_PROT_ALERT_ONLY 2
+
+#define MAX5970_REG_STATUS2 0x33
+#define MAX5970_IRNG_MASK 0x3
+#define MAX5970_IRNG(reg, ch) \
+ (((reg) >> ((ch) * 2)) & MAX5970_IRNG_MASK)
+
+#define MAX5970_REG_STATUS3 0x34
+#define MAX5970_STATUS3_ALERT BIT(4)
+#define MAX5970_STATUS3_PG(ch) BIT(ch)
+
+#define MAX5970_REG_FAULT0 0x35
+#define UV_STATUS_WARN(ch) BIT(ch)
+#define UV_STATUS_CRIT(ch) BIT(ch + 4)
+
+#define MAX5970_REG_FAULT1 0x36
+#define OV_STATUS_WARN(ch) BIT(ch)
+#define OV_STATUS_CRIT(ch) BIT(ch + 4)
+
+#define MAX5970_REG_FAULT2 0x37
+#define OC_STATUS_WARN(ch) BIT(ch)
+
+#define MAX5970_REG_CHXEN 0x3b
+#define CHXEN(ch) (3 << (ch * 2))
+
+#define MAX5970_REG_LED_FLASH 0x43
+
+#define MAX_REGISTERS 0x49
+#define ADC_MASK 0x3FF
+
+struct max597x_data {
+ struct device *dev;
+ int irq;
+ int num_switches;
+ struct regmap *regmap;
+ /* Chip specific parameters needed by regulator & iio cells */
+ u32 irng[MAX5970_NUM_SWITCHES];
+ u32 mon_rng[MAX5970_NUM_SWITCHES];
+ u32 shunt_micro_ohms[MAX5970_NUM_SWITCHES];
+};
+
+#endif /* _MAX597X_H */
--
2.37.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978
2022-11-01 16:53 ` [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978 Naresh Solanki
@ 2022-11-02 2:26 ` Rob Herring
2022-11-02 17:19 ` Krzysztof Kozlowski
1 sibling, 0 replies; 5+ messages in thread
From: Rob Herring @ 2022-11-02 2:26 UTC (permalink / raw)
To: Naresh Solanki
Cc: devicetree, Patrick Rudolph, Rob Herring, Krzysztof Kozlowski,
Marcello Sylvester Bauer, linux-kernel, Naresh Solanki,
Lee Jones
On Tue, 01 Nov 2022 17:53:43 +0100, Naresh Solanki wrote:
> From: Marcello Sylvester Bauer <sylv@sylv.io>
>
> The MAX597x is a hot swap controller with configurable fault protection.
> It also has 10bit ADC for current & voltage measurements.
>
> Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
> Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
> Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
> ---
> .../devicetree/bindings/mfd/max5970.yaml | 164 ++++++++++++++++++
> 1 file changed, 164 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/max5970.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/mfd/max5970.example.dts:21.22-34.19: Warning (i2c_bus_reg): /example-0/i2c/leds: missing or empty reg property
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/max5970.example.dtb: regulator@3a: 'vss2-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/max5970.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978
2022-11-01 16:53 ` [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978 Naresh Solanki
2022-11-02 2:26 ` Rob Herring
@ 2022-11-02 17:19 ` Krzysztof Kozlowski
1 sibling, 0 replies; 5+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-02 17:19 UTC (permalink / raw)
To: Naresh Solanki, linux-kernel, devicetree, Lee Jones, Rob Herring,
Krzysztof Kozlowski, Patrick Rudolph
Cc: Marcello Sylvester Bauer
On 01/11/2022 12:53, Naresh Solanki wrote:
> From: Marcello Sylvester Bauer <sylv@sylv.io>
>
> The MAX597x is a hot swap controller with configurable fault protection.
> It also has 10bit ADC for current & voltage measurements.
>
> Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
> Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
> Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
> ---
> .../devicetree/bindings/mfd/max5970.yaml | 164 ++++++++++++++++++
> 1 file changed, 164 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/max5970.yaml
>
> diff --git a/Documentation/devicetree/bindings/mfd/max5970.yaml b/Documentation/devicetree/bindings/mfd/max5970.yaml
> new file mode 100644
> index 000000000000..a0cc6a7543b5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/max5970.yaml
Filename: missing vendor prefix.
> @@ -0,0 +1,164 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/max5970.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Regulator driver for MAX5970 smart switch from Maxim Integrated.
Drop "driver"
> +
> +maintainers:
> + - Patrick Rudolph <patrick.rudolph@9elements.com>
> +
> +description: |
> + The smart switch provides no output regulation, but independent fault protection
> + and voltage and current sensing.
> + Programming is done through I2C bus.
> +
> + Datasheets:
> + https://datasheets.maximintegrated.com/en/ds/MAX5970.pdf
> + https://datasheets.maximintegrated.com/en/ds/MAX5978.pdf
> +
> +properties:
> + compatible:
> + enum:
> + - maxim,max5970
> + - maxim,max5978
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + leds:
> + type: object
> + description:
> + Properties for single channel.
> +
> + patternProperties:
> + "^led@[0-3]$":
> + $ref: /schemas/leds/common.yaml#
> + type: object
> +
> + additionalProperties: true
This should be rather: false
> +
> + vss1-supply:
> + description: Supply of the first channel.
> +
> + "#io-channel-cells":
> + const: 1
> +
> + regulators:
> + type: object
> + description:
> + Properties for single channel.
> +
> + patternProperties:
> + "^(sw[0-1])$":
> + $ref: /schemas/regulator/regulator.yaml#
> + type: object
> +
> + shunt-resistor-micro-ohms:
> + description: |
> + The value of curent sense resistor in microohms.
> + Must be specified for each channel.
> +
> + additionalProperties: true
> +
> +required:
> + - compatible
> + - reg
> + - regulators
> + - vss1-supply
> +
> +allOf:
> + - $ref: /schemas/regulator/regulator.yaml#
> + - if:
> + properties:
> + compatible:
> + enum:
> + - maxim,max5970
> + then:
> + properties:
> + vss2-supply:
> + description: Supply of the second channel.
> +
> + io-channels:
> + items:
> + - description: voltage first channel
> + - description: current first channel
> + - description: voltage second channel
> + - description: current second channel
> + description: |
> + Voltage and current for first and second channel.
> + required:
> + - vss2-supply
> +
> + else:
> + properties:
> + io-channels:
> + items:
> + - description: voltage first channel
> + - description: current first channel
> + description: |
> + Voltage and current for first channel.
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
Use 4 spaces for example indentation.
> + leds {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + led@0 {
> + reg = <0>;
> + label = "led0";
> + default-state = "on";
> + };
> + led@1 {
> + reg = <1>;
> + label = "led1";
> + default-state = "on";
> + };
> + };
What is this example about? It does not match your bindings.
> + regulator@3a {
> + reg = <0x3a>;
> + vss1-supply = <&p3v3>;
> + compatible = "maxim,max5978";
> +
> + regulators {
> + sw0_ref_0: SW0 {
Does not look like you tested the bindings. Please run `make
dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
> + regulator-compatible = "SW0";
> + shunt-resistor-micro-ohms = <12000>;
> + };
> + };
> + };
> + };
> +
> + - |
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + regulator@3a {
> + reg = <0x3a>;
> + vss1-supply = <&p3v3>;
> + vss2-supply = <&p5v>;
> + compatible = "maxim,max5970";
Compatible is first, then reg, then the rest.
> +
> + regulators {
> + sw0_ref_1: SW0 {
> + regulator-compatible = "SW0";
> + shunt-resistor-micro-ohms = <12000>;
> + };
> + sw1_ref_1: SW1 {
> + regulator-compatible = "SW1";
> + shunt-resistor-micro-ohms = <10000>;
> + };
> + };
> + };
> + };
> +...
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2022-11-02 17:19 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-01 16:53 [PATCH v4 0/2] mfd: max597x: Add support for max597x Naresh Solanki
2022-11-01 16:53 ` [PATCH v4 1/2] dt-bindings: mfd: Add bindings for MAX5970 and MAX5978 Naresh Solanki
2022-11-02 2:26 ` Rob Herring
2022-11-02 17:19 ` Krzysztof Kozlowski
2022-11-01 16:53 ` [PATCH v4 2/2] mfd: max597x: Add support " Naresh Solanki
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).