[PATCH 0/3] arm64: dts: qcom: msm8916-acer-a1-724: Add initial device tree

[PATCH 0/3] arm64: dts: qcom: msm8916-acer-a1-724: Add initial device tree

[Lin, Meng-Bo]

Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
in 2014.

Note: The original firmware from Acer can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
didn't set up (firmware) secure boot.

Add a device tree for with initial support for:

- GPIO keys
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators
- Bosch BMC150 accelerometer/magnetometer

[PATCH 1/3] dt-bindings: qcom: Document bindings for new msm8916-acer-a7-724 device

[Lin, Meng-Bo]

Document the new acer,a1-724 device tree bindings used in its device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 463509f0f23a..83f6748979a9 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -180,6 +180,7 @@ properties:
 
       - items:
           - enum:
+              - acer,a1-724
               - alcatel,idol347
               - asus,z00l
               - huawei,g7
-- 
2.30.2

[PATCH 3/3] arm64: dts: qcom: msm8916-acer-a1-724: Add accelerometer/magnetometer

[Lin, Meng-Bo]

Iconia Talk S uses a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
---
 .../boot/dts/qcom/msm8916-acer-a1-724.dts     | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
index acd909551a75..3461a39ee866 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -6,6 +6,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 /*
  * NOTE: The original firmware from Acer can only boot 32-bit kernels.
@@ -51,6 +52,35 @@ usb_id: usb-id {
 	};
 };
 
+&blsp_i2c2 {
+	status = "okay";
+
+	accelerometer@10 {
+		compatible = "bosch,bmc150_accel";
+		reg = <0x10>;
+		interrupt-parent = <&msmgpio>;
+		interrupts = <115 IRQ_TYPE_EDGE_RISING>;
+
+		vdd-supply = <&pm8916_l17>;
+		vddio-supply = <&pm8916_l6>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default>;
+
+		mount-matrix = "0", "-1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "1";
+	};
+
+	magnetometer@12 {
+		compatible = "bosch,bmc150_magn";
+		reg = <0x12>;
+
+		vdd-supply = <&pm8916_l17>;
+		vddio-supply = <&pm8916_l6>;
+	};
+};
+
 &blsp1_uart2 {
 	status = "okay";
 };
@@ -199,6 +229,14 @@ l18 {
 };
 
 &msmgpio {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio115";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	gpio_keys_default: gpio-keys-default-state {
 		pins = "gpio107";
 		function = "gpio";
-- 
2.30.2

[PATCH 2/3] arm64: dts: qcom: msm8916-acer-a1-724: Add initial device tree

[Lin, Meng-Bo]

Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
in 2014.

Note: The original firmware from Acer can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
didn't set up (firmware) secure boot.

Add a device tree for with initial support for:

- GPIO keys
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/msm8916-acer-a1-724.dts     | 217 ++++++++++++++++++
 2 files changed, 218 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index afe496a93f94..f38a20074013 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c2.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-acer-a1-724.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-alcatel-idol347.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-asus-z00l.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-huawei-g7.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
new file mode 100644
index 000000000000..acd909551a75
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/*
+ * NOTE: The original firmware from Acer can only boot 32-bit kernels.
+ * To boot this device tree using arm64 it is necessary to flash 64-bit
+ * TZ/HYP firmware (e.g. taken from the DragonBoard 410c).
+ * See https://wiki.postmarketos.org/wiki/Acer_Iconia_Talk_S_(acer-a1-724)
+ * for suggested installation instructions.
+ */
+
+/ {
+	model = "Acer Iconia Talk S A1-724";
+	compatible = "acer,a1-724", "qcom,msm8916";
+	chassis-type = "tablet";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		label = "GPIO Buttons";
+
+		button-volume-up {
+			label = "Volume Up";
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	usb_id: usb-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_id_default>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&pm8916_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pm8916_vib {
+	status = "okay";
+};
+
+&pronto {
+	status = "okay";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+
+	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>;
+};
+
+&usb {
+	status = "okay";
+	extcon = <&usb_id>, <&usb_id>;
+};
+
+&usb_hs_phy {
+	extcon = <&usb_id>;
+};
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1300000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2100000>;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l16 {
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l17 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
+
+&msmgpio {
+	gpio_keys_default: gpio-keys-default-state {
+		pins = "gpio107";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	usb_id_default: usb-id-default-state {
+		pins = "gpio110";
+		function = "gpio";
+
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+};
-- 
2.30.2

Re: [PATCH 1/3] dt-bindings: qcom: Document bindings for new msm8916-acer-a7-724 device

[Krzysztof Kozlowski]

On 19/11/2022 20:48, Lin, Meng-Bo wrote:
> Document the new acer,a1-724 device tree bindings used in its device tree.
> 
> Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>

Same comments as for your other binding patch

Best regards,
Krzysztof

Re: [PATCH 3/3] arm64: dts: qcom: msm8916-acer-a1-724: Add accelerometer/magnetometer

[Konrad Dybcio]

On 19.11.2022 20:48, Lin, Meng-Bo wrote:
> Iconia Talk S uses a Bosch BMC150 accelerometer/magnetometer combo.
> The chip provides two separate I2C devices for the accelerometer
> and magnetometer that are already supported by the bmc150-accel
> and bmc150-magn driver.
> 
> Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  .../boot/dts/qcom/msm8916-acer-a1-724.dts     | 38 +++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> index acd909551a75..3461a39ee866 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> +++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> @@ -6,6 +6,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  /*
>   * NOTE: The original firmware from Acer can only boot 32-bit kernels.
> @@ -51,6 +52,35 @@ usb_id: usb-id {
>  	};
>  };
>  
> +&blsp_i2c2 {
> +	status = "okay";
> +
> +	accelerometer@10 {
> +		compatible = "bosch,bmc150_accel";
> +		reg = <0x10>;
> +		interrupt-parent = <&msmgpio>;
> +		interrupts = <115 IRQ_TYPE_EDGE_RISING>;
> +
> +		vdd-supply = <&pm8916_l17>;
> +		vddio-supply = <&pm8916_l6>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&accel_int_default>;
> +
> +		mount-matrix = "0", "-1", "0",
> +			       "-1", "0", "0",
> +			       "0", "0", "1";
> +	};
> +
> +	magnetometer@12 {
> +		compatible = "bosch,bmc150_magn";
> +		reg = <0x12>;
> +
> +		vdd-supply = <&pm8916_l17>;
> +		vddio-supply = <&pm8916_l6>;
> +	};
> +};
> +
>  &blsp1_uart2 {
>  	status = "okay";
>  };
> @@ -199,6 +229,14 @@ l18 {
>  };
>  
>  &msmgpio {
> +	accel_int_default: accel-int-default-state {
> +		pins = "gpio115";
> +		function = "gpio";
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
>  	gpio_keys_default: gpio-keys-default-state {
>  		pins = "gpio107";
>  		function = "gpio";

Re: [PATCH 2/3] arm64: dts: qcom: msm8916-acer-a1-724: Add initial device tree

[Konrad Dybcio]

On 19.11.2022 20:48, Lin, Meng-Bo wrote:
> Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
> in 2014.
> 
> Note: The original firmware from Acer can only boot 32-bit kernels.
> To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
> with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
> didn't set up (firmware) secure boot.
> 
> Add a device tree for with initial support for:
> 
> - GPIO keys
> - pm8916-vibrator
> - SDHCI (internal and external storage)
> - USB Device Mode
> - UART
> - WCNSS (WiFi/BT)
> - Regulators
> 
> Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/msm8916-acer-a1-724.dts     | 217 ++++++++++++++++++
>  2 files changed, 218 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index afe496a93f94..f38a20074013 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c1.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c2.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-acer-a1-724.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-alcatel-idol347.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-asus-z00l.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-huawei-g7.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> new file mode 100644
> index 000000000000..acd909551a75
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> @@ -0,0 +1,217 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/dts-v1/;
> +
> +#include "msm8916-pm8916.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/*
> + * NOTE: The original firmware from Acer can only boot 32-bit kernels.
> + * To boot this device tree using arm64 it is necessary to flash 64-bit
> + * TZ/HYP firmware (e.g. taken from the DragonBoard 410c).
> + * See https://wiki.postmarketos.org/wiki/Acer_Iconia_Talk_S_(acer-a1-724)
> + * for suggested installation instructions.
> + */
> +
> +/ {
> +	model = "Acer Iconia Talk S A1-724";
> +	compatible = "acer,a1-724", "qcom,msm8916";
> +	chassis-type = "tablet";
> +
> +	aliases {
> +		serial0 = &blsp1_uart2;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gpio_keys_default>;
> +
> +		label = "GPIO Buttons";
> +
> +		button-volume-up {
> +			label = "Volume Up";
> +			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +		};
> +	};
> +
> +	usb_id: usb-id {
> +		compatible = "linux,extcon-usb-gpio";
> +		id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_id_default>;
> +	};
> +};
> +
> +&blsp1_uart2 {
> +	status = "okay";
> +};
> +
> +&pm8916_resin {
> +	status = "okay";
> +	linux,code = <KEY_VOLUMEDOWN>;
> +};
> +
> +&pm8916_vib {
> +	status = "okay";
> +};
> +
> +&pronto {
> +	status = "okay";
> +};
> +
> +&sdhc_1 {
> +	status = "okay";
status last, please.

> +
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
> +	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
> +};
> +
> +&sdhc_2 {
> +	status = "okay";
> +
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
> +	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
> +
> +	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&usb {
> +	status = "okay";
> +	extcon = <&usb_id>, <&usb_id>;
> +};
> +
> +&usb_hs_phy {
> +	extcon = <&usb_id>;
> +};
These usb references are not sorted alphabetically.

> +
> +&smd_rpm_regulators {
> +	vdd_l1_l2_l3-supply = <&pm8916_s3>;
> +	vdd_l4_l5_l6-supply = <&pm8916_s4>;
> +	vdd_l7-supply = <&pm8916_s4>;
> +
> +	s3 {
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1300000>;
> +	};
> +
> +	s4 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <2100000>;
> +	};
> +
> +	l1 {
> +		regulator-min-microvolt = <1225000>;
> +		regulator-max-microvolt = <1225000>;
> +	};
> +
> +	l2 {
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +	};
> +
> +	l4 {
> +		regulator-min-microvolt = <2050000>;
> +		regulator-max-microvolt = <2050000>;
> +	};
> +
> +	l5 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	l6 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	l7 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	l8 {
> +		regulator-min-microvolt = <2850000>;
> +		regulator-max-microvolt = <2900000>;
> +	};
> +
> +	l9 {
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l10 {
> +		regulator-min-microvolt = <2700000>;
> +		regulator-max-microvolt = <2800000>;
> +	};
> +
> +	l11 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <2950000>;
> +		regulator-allow-set-load;
> +		regulator-system-load = <200000>;
Please swap these last two properties.

Looks good otherwise.

Konrad
> +	};
> +
> +	l12 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <2950000>;
> +	};
> +
> +	l13 {
> +		regulator-min-microvolt = <3075000>;
> +		regulator-max-microvolt = <3075000>;
> +	};
> +
> +	l14 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l15 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l16 {
> +		regulator-min-microvolt = <2900000>;
> +		regulator-max-microvolt = <2900000>;
> +	};
> +
> +	l17 {
> +		regulator-min-microvolt = <2850000>;
> +		regulator-max-microvolt = <2850000>;
> +	};
> +
> +	l18 {
> +		regulator-min-microvolt = <2700000>;
> +		regulator-max-microvolt = <2700000>;
> +	};
> +};
> +
> +&msmgpio {
> +	gpio_keys_default: gpio-keys-default-state {
> +		pins = "gpio107";
> +		function = "gpio";
> +
> +		drive-strength = <2>;
> +		bias-pull-up;
> +	};
> +
> +	usb_id_default: usb-id-default-state {
> +		pins = "gpio110";
> +		function = "gpio";
> +
> +		drive-strength = <8>;
> +		bias-pull-up;
> +	};
> +};