[PATCH v5 00/22] Restructure RPM SMD ICC

[PATCH v5 00/22] Restructure RPM SMD ICC

[Konrad Dybcio]

This series reshuffles things around, moving the management of SMD RPM
bus clocks to the interconnect framework where they belong. This helps
us solve a couple of issues:

1. We can work towards unused clk cleanup of RPMCC without worrying
   about it killing some NoC bus, resulting in the SoC dying.
   Deasserting actually unused RPM clocks (among other things) will
   let us achieve "true SoC-wide power collapse states", also known as
   VDD_LOW and VDD_MIN.

2. We no longer have to keep tons of quirky bus clock ifs in the icc
   driver. You either have a RPM clock and call "rpm set rate" or you
   have a single non-RPM clock (like AHB_CLK_SRC) or you don't have any.

3. There's less overhead - instead of going through layers and layers of
   the CCF, ratesetting comes down to calling max() and sending a single
   RPM message. ICC is very very dynamic so that's a big plus.

The clocks still need to be vaguely described in the clk-smd-rpm driver,
as it gives them an initial kickoff, before actually telling RPM to
enable DVFS scaling.  After RPM receives that command, all clocks that
have not been assigned a rate are considered unused and are shut down
in hardware, leading to the same issue as described in point 1.

We can consider marking them __initconst in the future, but this series
is very fat even without that..

Apart from that, it squashes a couple of bugs that really need fixing..

--- MERGING STRATEGY ---
If Stephen and Georgi agree, it would be best to take all of this through
the qcom tree, as it touches on heavily intertwined components and
introduces compile-time dependencies between icc and clk drivers.

Tested on SM6375 (OOT), MSM8998 (OOT), MSM8996.

MSM8974 conversion to common code and modernization will be handled separately.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Changes in v5:
- Pass RPM context id to qcom_icc_rpm_set_bus_rate()
- Fix min_t call cutting off bits 32-63 in set() path
- Pick up tags
- Link to v4: https://lore.kernel.org/r/20230526-topic-smd_icc-v4-0-5ba82b6fbba2@linaro.org

Changes in v4:
- Only set clk rate on a context if necessary
- Mention qcom,icc.h is not the correct header in "Control bus rpmcc form icc"
- Fix the bindings (BIT vs 1<<)
- Fix one more wrong use of qcom,icc.h in "Fix bucket numer" and uninclude it
- Drop "Allow negative QoS offset" (will be handled separately)
- Export icc clocks descriptions to unbreak =m builds
- Pick up tags
- Link to v3: https://lore.kernel.org/r/20230526-topic-smd_icc-v3-0-5fb7d39b874f@linaro.org

Changes in v3:
- Use devm_clk_get_optional and only get() the clock once
- Drop unnecessary NULL-checks for qp->bus_clk
- Handle ARM32 CCF limitations, add an explicit comment about them
- Use Stephan's alternative rpmcc readiness check
- Fix one more wrong usage of QCOM_ICC_NUM_BUCKETS in icc-rpm.h
- Introduce new dt-bindings for icc rpm tags
- Mention the rpm tags situation in the commit message of
  "Fix bucket number"
- Pick up tags
- Link to v2: https://lore.kernel.org/r/20230526-topic-smd_icc-v2-0-e5934b07d813@linaro.org

Changes in v2:
- Sort entries properly in "Add missing headers in icc-rpm.h"
- Fix the check for no clocks on a given provider
- Replace "Divide clk rate by src node bus width" with a proper fix
- Add "Set correct bandwidth through RPM bw req"
- Split "Add QCOM_SMD_RPM_STATE_NUM" into 2 logical changes
- Move "Separate out interconnect bus clocks" a bit later in the series
- Link to v1: https://lore.kernel.org/r/20230526-topic-smd_icc-v1-0-1bf8e6663c4e@linaro.org

---
Konrad Dybcio (21):
      dt-bindings: interconnect: Add Qcom RPM ICC bindings
      soc: qcom: smd-rpm: Add QCOM_SMD_RPM_STATE_NUM
      soc: qcom: smd-rpm: Use tabs for defines
      clk: qcom: smd-rpm: Move some RPM resources to the common header
      interconnect: qcom: icc-rpm: Introduce keep_alive
      interconnect: qcom: Fold smd-rpm.h into icc-rpm.h
      interconnect: qcom: smd-rpm: Add rpmcc handling skeleton code
      interconnect: qcom: Add missing headers in icc-rpm.h
      interconnect: qcom: Define RPM bus clocks
      interconnect: qcom: sdm660: Hook up RPM bus clk definitions
      interconnect: qcom: msm8996: Hook up RPM bus clk definitions
      interconnect: qcom: qcs404: Hook up RPM bus clk definitions
      interconnect: qcom: msm8939: Hook up RPM bus clk definitions
      interconnect: qcom: msm8916: Hook up RPM bus clk definitions
      interconnect: qcom: qcm2290: Hook up RPM bus clk definitions
      interconnect: qcom: icc-rpm: Control bus rpmcc from icc
      clk: qcom: smd-rpm: Separate out interconnect bus clocks
      interconnect: qcom: icc-rpm: Fix bucket number
      interconnect: qcom: icc-rpm: Set bandwidth on both contexts
      interconnect: qcom: icc-rpm: Set correct bandwidth through RPM bw req
      interconnect: qcom: icc-rpm: Fix bandwidth calculations

Stephan Gerhold (1):
      soc: qcom: smd-rpm: Move icc_smd_rpm registration to clk-smd-rpm

 drivers/clk/qcom/clk-smd-rpm.c                  | 312 +++++++++++-------------
 drivers/interconnect/qcom/Makefile              |   2 +-
 drivers/interconnect/qcom/icc-rpm-clocks.c      |  77 ++++++
 drivers/interconnect/qcom/icc-rpm.c             | 219 +++++++++--------
 drivers/interconnect/qcom/icc-rpm.h             |  55 ++++-
 drivers/interconnect/qcom/msm8916.c             |   4 +-
 drivers/interconnect/qcom/msm8939.c             |   5 +-
 drivers/interconnect/qcom/msm8974.c             |   2 +-
 drivers/interconnect/qcom/msm8996.c             |   9 +-
 drivers/interconnect/qcom/qcm2290.c             |   7 +-
 drivers/interconnect/qcom/qcs404.c              |   4 +-
 drivers/interconnect/qcom/sdm660.c              |   7 +-
 drivers/interconnect/qcom/smd-rpm.c             |  23 +-
 drivers/interconnect/qcom/smd-rpm.h             |  15 --
 drivers/soc/qcom/smd-rpm.c                      |  17 +-
 include/dt-bindings/interconnect/qcom,rpm-icc.h |  13 +
 include/linux/soc/qcom/smd-rpm.h                |  20 +-
 17 files changed, 454 insertions(+), 337 deletions(-)
---
base-commit: 1f6ce8392d6ff486af5ca96df9ded5882c4b6977
change-id: 20230526-topic-smd_icc-b8213948a5ed

Best regards,
-- 
Konrad Dybcio <konrad.dybcio@linaro.org>

[PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Konrad Dybcio]

The SMD RPM interconnect driver requires different icc tags to the
RPMh driver. Add bindings to reflect that.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 include/dt-bindings/interconnect/qcom,rpm-icc.h | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/include/dt-bindings/interconnect/qcom,rpm-icc.h b/include/dt-bindings/interconnect/qcom,rpm-icc.h
new file mode 100644
index 000000000000..2cd56f91e5c5
--- /dev/null
+++ b/include/dt-bindings/interconnect/qcom,rpm-icc.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
+#define __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
+
+#define RPM_ACTIVE_TAG		(1 << 0)
+#define RPM_SLEEP_TAG		(1 << 1)
+#define RPM_ALWAYS_TAG		(RPM_ACTIVE_TAG | RPM_SLEEP_TAG)
+
+#endif

-- 
2.41.0

Re: [PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Krzysztof Kozlowski]

On 14/06/2023 12:22, Konrad Dybcio wrote:
> The SMD RPM interconnect driver requires different icc tags to the
> RPMh driver. Add bindings to reflect that.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  include/dt-bindings/interconnect/qcom,rpm-icc.h | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/include/dt-bindings/interconnect/qcom,rpm-icc.h b/include/dt-bindings/interconnect/qcom,rpm-icc.h
> new file mode 100644
> index 000000000000..2cd56f91e5c5
> --- /dev/null
> +++ b/include/dt-bindings/interconnect/qcom,rpm-icc.h
> @@ -0,0 +1,13 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
> +/*
> + * Copyright (c) 2023, Linaro Limited
> + */
> +
> +#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
> +#define __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
> +
> +#define RPM_ACTIVE_TAG		(1 << 0)
> +#define RPM_SLEEP_TAG		(1 << 1)
> +#define RPM_ALWAYS_TAG		(RPM_ACTIVE_TAG | RPM_SLEEP_TAG)

Where are these used? I don't see any DTS in your patchset. Did you send
it separately?

Best regards,
Krzysztof

Re: [PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Konrad Dybcio]

On 14.06.2023 18:43, Krzysztof Kozlowski wrote:
> On 14/06/2023 12:22, Konrad Dybcio wrote:
>> The SMD RPM interconnect driver requires different icc tags to the
>> RPMh driver. Add bindings to reflect that.
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>>  include/dt-bindings/interconnect/qcom,rpm-icc.h | 13 +++++++++++++
>>  1 file changed, 13 insertions(+)
>>
>> diff --git a/include/dt-bindings/interconnect/qcom,rpm-icc.h b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>> new file mode 100644
>> index 000000000000..2cd56f91e5c5
>> --- /dev/null
>> +++ b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>> @@ -0,0 +1,13 @@
>> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
>> +/*
>> + * Copyright (c) 2023, Linaro Limited
>> + */
>> +
>> +#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>> +#define __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>> +
>> +#define RPM_ACTIVE_TAG		(1 << 0)
>> +#define RPM_SLEEP_TAG		(1 << 1)
>> +#define RPM_ALWAYS_TAG		(RPM_ACTIVE_TAG | RPM_SLEEP_TAG)
> 
> Where are these used? I don't see any DTS in your patchset. Did you send
> it separately?
In the driver for now, e.g. patch 19. DTS can only come after the
driver is fixed or things will explode!

Konrad
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Krzysztof Kozlowski]

On 14/06/2023 18:43, Konrad Dybcio wrote:
> On 14.06.2023 18:43, Krzysztof Kozlowski wrote:
>> On 14/06/2023 12:22, Konrad Dybcio wrote:
>>> The SMD RPM interconnect driver requires different icc tags to the
>>> RPMh driver. Add bindings to reflect that.
>>>
>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>> ---
>>>  include/dt-bindings/interconnect/qcom,rpm-icc.h | 13 +++++++++++++
>>>  1 file changed, 13 insertions(+)
>>>
>>> diff --git a/include/dt-bindings/interconnect/qcom,rpm-icc.h b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>>> new file mode 100644
>>> index 000000000000..2cd56f91e5c5
>>> --- /dev/null
>>> +++ b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>>> @@ -0,0 +1,13 @@
>>> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
>>> +/*
>>> + * Copyright (c) 2023, Linaro Limited
>>> + */
>>> +
>>> +#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>>> +#define __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>>> +
>>> +#define RPM_ACTIVE_TAG		(1 << 0)
>>> +#define RPM_SLEEP_TAG		(1 << 1)
>>> +#define RPM_ALWAYS_TAG		(RPM_ACTIVE_TAG | RPM_SLEEP_TAG)
>>
>> Where are these used? I don't see any DTS in your patchset. Did you send
>> it separately?
> In the driver for now, e.g. patch 19. DTS can only come after the
> driver is fixed or things will explode!

You reference it in patch 19, but I still do not see the constants being
used.

Best regards,
Krzysztof

Re: [PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Konrad Dybcio]

On 14.06.2023 18:47, Krzysztof Kozlowski wrote:
> On 14/06/2023 18:43, Konrad Dybcio wrote:
>> On 14.06.2023 18:43, Krzysztof Kozlowski wrote:
>>> On 14/06/2023 12:22, Konrad Dybcio wrote:
>>>> The SMD RPM interconnect driver requires different icc tags to the
>>>> RPMh driver. Add bindings to reflect that.
>>>>
>>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>>> ---
>>>>  include/dt-bindings/interconnect/qcom,rpm-icc.h | 13 +++++++++++++
>>>>  1 file changed, 13 insertions(+)
>>>>
>>>> diff --git a/include/dt-bindings/interconnect/qcom,rpm-icc.h b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>>>> new file mode 100644
>>>> index 000000000000..2cd56f91e5c5
>>>> --- /dev/null
>>>> +++ b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>>>> @@ -0,0 +1,13 @@
>>>> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
>>>> +/*
>>>> + * Copyright (c) 2023, Linaro Limited
>>>> + */
>>>> +
>>>> +#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>>>> +#define __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>>>> +
>>>> +#define RPM_ACTIVE_TAG		(1 << 0)
>>>> +#define RPM_SLEEP_TAG		(1 << 1)
>>>> +#define RPM_ALWAYS_TAG		(RPM_ACTIVE_TAG | RPM_SLEEP_TAG)
>>>
>>> Where are these used? I don't see any DTS in your patchset. Did you send
>>> it separately?
>> In the driver for now, e.g. patch 19. DTS can only come after the
>> driver is fixed or things will explode!
> 
> You reference it in patch 19, but I still do not see the constants being
> used.

Fragment of P19:

 	if (!tag)
-		tag = QCOM_ICC_TAG_ALWAYS;
+		tag = RPM_ALWAYS_TAG;
 

Konrad
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Krzysztof Kozlowski]

On 14/06/2023 18:48, Konrad Dybcio wrote:
> On 14.06.2023 18:47, Krzysztof Kozlowski wrote:
>> On 14/06/2023 18:43, Konrad Dybcio wrote:
>>> On 14.06.2023 18:43, Krzysztof Kozlowski wrote:
>>>> On 14/06/2023 12:22, Konrad Dybcio wrote:
>>>>> The SMD RPM interconnect driver requires different icc tags to the
>>>>> RPMh driver. Add bindings to reflect that.
>>>>>
>>>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>>>> ---
>>>>>  include/dt-bindings/interconnect/qcom,rpm-icc.h | 13 +++++++++++++
>>>>>  1 file changed, 13 insertions(+)
>>>>>
>>>>> diff --git a/include/dt-bindings/interconnect/qcom,rpm-icc.h b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>>>>> new file mode 100644
>>>>> index 000000000000..2cd56f91e5c5
>>>>> --- /dev/null
>>>>> +++ b/include/dt-bindings/interconnect/qcom,rpm-icc.h
>>>>> @@ -0,0 +1,13 @@
>>>>> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
>>>>> +/*
>>>>> + * Copyright (c) 2023, Linaro Limited
>>>>> + */
>>>>> +
>>>>> +#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>>>>> +#define __DT_BINDINGS_INTERCONNECT_QCOM_RPM_ICC_H
>>>>> +
>>>>> +#define RPM_ACTIVE_TAG		(1 << 0)
>>>>> +#define RPM_SLEEP_TAG		(1 << 1)
>>>>> +#define RPM_ALWAYS_TAG		(RPM_ACTIVE_TAG | RPM_SLEEP_TAG)
>>>>
>>>> Where are these used? I don't see any DTS in your patchset. Did you send
>>>> it separately?
>>> In the driver for now, e.g. patch 19. DTS can only come after the
>>> driver is fixed or things will explode!
>>
>> You reference it in patch 19, but I still do not see the constants being
>> used.
> 
> Fragment of P19:
> 
>  	if (!tag)
> -		tag = QCOM_ICC_TAG_ALWAYS;
> +		tag = RPM_ALWAYS_TAG;

Now I see, thanks:)

Best regards,
Krzysztof

Re: [PATCH v5 01/22] dt-bindings: interconnect: Add Qcom RPM ICC bindings

[Krzysztof Kozlowski]

On 14/06/2023 12:22, Konrad Dybcio wrote:
> The SMD RPM interconnect driver requires different icc tags to the
> RPMh driver. Add bindings to reflect that.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

[PATCH v5 02/22] soc: qcom: smd-rpm: Add QCOM_SMD_RPM_STATE_NUM

[Konrad Dybcio]

Add a preprocessor define to indicate the number of RPM contexts/states.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 include/linux/soc/qcom/smd-rpm.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/include/linux/soc/qcom/smd-rpm.h b/include/linux/soc/qcom/smd-rpm.h
index 2990f425fdef..e468f94fa323 100644
--- a/include/linux/soc/qcom/smd-rpm.h
+++ b/include/linux/soc/qcom/smd-rpm.h
@@ -6,6 +6,7 @@ struct qcom_smd_rpm;
 
 #define QCOM_SMD_RPM_ACTIVE_STATE        0
 #define QCOM_SMD_RPM_SLEEP_STATE         1
+#define QCOM_SMD_RPM_STATE_NUM		2
 
 /*
  * Constants used for addressing resources in the RPM.

-- 
2.41.0

[PATCH v5 03/22] soc: qcom: smd-rpm: Use tabs for defines

[Konrad Dybcio]

Use tabs for defines to make things spaced consistently.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 include/linux/soc/qcom/smd-rpm.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/include/linux/soc/qcom/smd-rpm.h b/include/linux/soc/qcom/smd-rpm.h
index e468f94fa323..99499e4b080e 100644
--- a/include/linux/soc/qcom/smd-rpm.h
+++ b/include/linux/soc/qcom/smd-rpm.h
@@ -4,8 +4,8 @@
 
 struct qcom_smd_rpm;
 
-#define QCOM_SMD_RPM_ACTIVE_STATE        0
-#define QCOM_SMD_RPM_SLEEP_STATE         1
+#define QCOM_SMD_RPM_ACTIVE_STATE	0
+#define QCOM_SMD_RPM_SLEEP_STATE	1
 #define QCOM_SMD_RPM_STATE_NUM		2
 
 /*

-- 
2.41.0

[PATCH v5 04/22] clk: qcom: smd-rpm: Move some RPM resources to the common header

[Konrad Dybcio]

In preparation for handling the bus clocks in the icc driver, carve out
some defines and a struct definition to the common rpm header.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/clk/qcom/clk-smd-rpm.c   | 13 -------------
 include/linux/soc/qcom/smd-rpm.h | 15 +++++++++++++++
 2 files changed, 15 insertions(+), 13 deletions(-)

diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c
index e4de74b68797..937cb1515968 100644
--- a/drivers/clk/qcom/clk-smd-rpm.c
+++ b/drivers/clk/qcom/clk-smd-rpm.c
@@ -18,13 +18,6 @@
 
 #include <dt-bindings/clock/qcom,rpmcc.h>
 
-#define QCOM_RPM_KEY_SOFTWARE_ENABLE			0x6e657773
-#define QCOM_RPM_KEY_PIN_CTRL_CLK_BUFFER_ENABLE_KEY	0x62636370
-#define QCOM_RPM_SMD_KEY_RATE				0x007a484b
-#define QCOM_RPM_SMD_KEY_ENABLE				0x62616e45
-#define QCOM_RPM_SMD_KEY_STATE				0x54415453
-#define QCOM_RPM_SCALING_ENABLE_ID			0x2
-
 #define __DEFINE_CLK_SMD_RPM_PREFIX(_prefix, _name, _active,		      \
 				    type, r_id, key)			      \
 	static struct clk_smd_rpm clk_smd_rpm_##_prefix##_active;	      \
@@ -171,12 +164,6 @@ struct clk_smd_rpm {
 	unsigned long rate;
 };
 
-struct clk_smd_rpm_req {
-	__le32 key;
-	__le32 nbytes;
-	__le32 value;
-};
-
 struct rpm_smd_clk_desc {
 	struct clk_smd_rpm **clks;
 	size_t num_clks;
diff --git a/include/linux/soc/qcom/smd-rpm.h b/include/linux/soc/qcom/smd-rpm.h
index 99499e4b080e..8190878645f9 100644
--- a/include/linux/soc/qcom/smd-rpm.h
+++ b/include/linux/soc/qcom/smd-rpm.h
@@ -2,6 +2,8 @@
 #ifndef __QCOM_SMD_RPM_H__
 #define __QCOM_SMD_RPM_H__
 
+#include <linux/types.h>
+
 struct qcom_smd_rpm;
 
 #define QCOM_SMD_RPM_ACTIVE_STATE	0
@@ -45,6 +47,19 @@ struct qcom_smd_rpm;
 #define QCOM_SMD_RPM_PKA_CLK	0x616b70
 #define QCOM_SMD_RPM_MCFG_CLK	0x6766636d
 
+#define QCOM_RPM_KEY_SOFTWARE_ENABLE			0x6e657773
+#define QCOM_RPM_KEY_PIN_CTRL_CLK_BUFFER_ENABLE_KEY	0x62636370
+#define QCOM_RPM_SMD_KEY_RATE				0x007a484b
+#define QCOM_RPM_SMD_KEY_ENABLE				0x62616e45
+#define QCOM_RPM_SMD_KEY_STATE				0x54415453
+#define QCOM_RPM_SCALING_ENABLE_ID			0x2
+
+struct clk_smd_rpm_req {
+	__le32 key;
+	__le32 nbytes;
+	__le32 value;
+};
+
 int qcom_rpm_smd_write(struct qcom_smd_rpm *rpm,
 		       int state,
 		       u32 resource_type, u32 resource_id,

-- 
2.41.0

[PATCH v5 05/22] soc: qcom: smd-rpm: Move icc_smd_rpm registration to clk-smd-rpm

[Konrad Dybcio]

From: Stephan Gerhold <stephan@gerhold.net>

icc_smd_rpm will do bus clock votes itself rather than taking the
unnecessary detour through the clock subsystem. However, it can only
do that after the clocks have been handed off and scaling has been
enabled in the RPM in clk-smd-rpm.

Move the icc_smd_rpm registration from smd-rpm.c to clk-smd-rpm.c
to avoid any possible races. icc_smd_rpm gets the driver data from
the smd-rpm device, so still register the platform device on the
smd-rpm parent device.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Konrad: remove unrelated cleanups]
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/clk/qcom/clk-smd-rpm.c | 21 +++++++++++++++++++++
 drivers/soc/qcom/smd-rpm.c     | 17 +----------------
 2 files changed, 22 insertions(+), 16 deletions(-)

diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c
index 937cb1515968..6e7f0438e8b8 100644
--- a/drivers/clk/qcom/clk-smd-rpm.c
+++ b/drivers/clk/qcom/clk-smd-rpm.c
@@ -1289,12 +1289,20 @@ static struct clk_hw *qcom_smdrpm_clk_hw_get(struct of_phandle_args *clkspec,
 	return desc->clks[idx] ? &desc->clks[idx]->hw : ERR_PTR(-ENOENT);
 }
 
+static void rpm_smd_unregister_icc(void *data)
+{
+	struct platform_device *icc_pdev = data;
+
+	platform_device_unregister(icc_pdev);
+}
+
 static int rpm_smd_clk_probe(struct platform_device *pdev)
 {
 	int ret;
 	size_t num_clks, i;
 	struct clk_smd_rpm **rpm_smd_clks;
 	const struct rpm_smd_clk_desc *desc;
+	struct platform_device *icc_pdev;
 
 	rpmcc_smd_rpm = dev_get_drvdata(pdev->dev.parent);
 	if (!rpmcc_smd_rpm) {
@@ -1344,6 +1352,19 @@ static int rpm_smd_clk_probe(struct platform_device *pdev)
 	if (ret)
 		goto err;
 
+	icc_pdev = platform_device_register_data(pdev->dev.parent,
+						 "icc_smd_rpm", -1, NULL, 0);
+	if (IS_ERR(icc_pdev)) {
+		dev_err(&pdev->dev, "Failed to register icc_smd_rpm device: %pE\n",
+			icc_pdev);
+		/* No need to unregister clocks because of this */
+	} else {
+		ret = devm_add_action_or_reset(&pdev->dev, rpm_smd_unregister_icc,
+					       icc_pdev);
+		if (ret)
+			goto err;
+	}
+
 	return 0;
 err:
 	dev_err(&pdev->dev, "Error registering SMD clock driver (%d)\n", ret);
diff --git a/drivers/soc/qcom/smd-rpm.c b/drivers/soc/qcom/smd-rpm.c
index 0c1aa809cc4e..577f1f25ab10 100644
--- a/drivers/soc/qcom/smd-rpm.c
+++ b/drivers/soc/qcom/smd-rpm.c
@@ -19,7 +19,6 @@
 /**
  * struct qcom_smd_rpm - state of the rpm device driver
  * @rpm_channel:	reference to the smd channel
- * @icc:		interconnect proxy device
  * @dev:		rpm device
  * @ack:		completion for acks
  * @lock:		mutual exclusion around the send/complete pair
@@ -27,7 +26,6 @@
  */
 struct qcom_smd_rpm {
 	struct rpmsg_endpoint *rpm_channel;
-	struct platform_device *icc;
 	struct device *dev;
 
 	struct completion ack;
@@ -197,7 +195,6 @@ static int qcom_smd_rpm_callback(struct rpmsg_device *rpdev,
 static int qcom_smd_rpm_probe(struct rpmsg_device *rpdev)
 {
 	struct qcom_smd_rpm *rpm;
-	int ret;
 
 	rpm = devm_kzalloc(&rpdev->dev, sizeof(*rpm), GFP_KERNEL);
 	if (!rpm)
@@ -210,23 +207,11 @@ static int qcom_smd_rpm_probe(struct rpmsg_device *rpdev)
 	rpm->rpm_channel = rpdev->ept;
 	dev_set_drvdata(&rpdev->dev, rpm);
 
-	rpm->icc = platform_device_register_data(&rpdev->dev, "icc_smd_rpm", -1,
-						 NULL, 0);
-	if (IS_ERR(rpm->icc))
-		return PTR_ERR(rpm->icc);
-
-	ret = of_platform_populate(rpdev->dev.of_node, NULL, NULL, &rpdev->dev);
-	if (ret)
-		platform_device_unregister(rpm->icc);
-
-	return ret;
+	return of_platform_populate(rpdev->dev.of_node, NULL, NULL, &rpdev->dev);
 }
 
 static void qcom_smd_rpm_remove(struct rpmsg_device *rpdev)
 {
-	struct qcom_smd_rpm *rpm = dev_get_drvdata(&rpdev->dev);
-
-	platform_device_unregister(rpm->icc);
 	of_platform_depopulate(&rpdev->dev);
 }
 

-- 
2.41.0

[PATCH v5 06/22] interconnect: qcom: icc-rpm: Introduce keep_alive

[Konrad Dybcio]

The downstream kernel employs the concept of "keeping the bus alive"
by voting for the minimum (XO/19.2MHz) rate at all times on certain
(well, most) buses. This is a very important thing to have, as if we
either have a lackluster/wrong DT that doesn't specify a (high enough)
vote on a certain bus, we may lose access to the entire bus altogether.
This is very apparent when we only start introducing interconnect
support on a given platform and haven't yet introduced voting on all
peripherals.

The same can happen if we only have a single driver casting a vote on
a certain bus and that driver exits/crashes/suspends.

The keepalive vote is limited to the ACTIVE bucket, as keeping a
permanent vote on the SLEEP one could prevent the platform from properly
entering low power mode states.

Introduce the very same concept, with a slight twist: the vendor
kernel checks whether the rate is zero before setting the minimum
vote, but that's rather silly, as in doing so we're at the mercy
of CCF. Instead, explicitly clamp the rates to always be >= 19.2 MHz
for providers with keep_alive=true.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c | 10 ++++++++++
 drivers/interconnect/qcom/icc-rpm.h |  3 +++
 2 files changed, 13 insertions(+)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index 6acc7686ed38..863e8ba1daa2 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -50,6 +50,8 @@
 #define NOC_QOS_MODE_FIXED_VAL		0x0
 #define NOC_QOS_MODE_BYPASS_VAL		0x2
 
+#define ICC_BUS_CLK_MIN_RATE		19200000ULL
+
 static int qcom_icc_set_qnoc_qos(struct icc_node *src)
 {
 	struct icc_provider *provider = src->provider;
@@ -380,6 +382,13 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 		do_div(rate, src_qn->buswidth);
 		rate = min_t(u64, rate, LONG_MAX);
 
+		/*
+		 * Downstream checks whether the requested rate is zero, but it makes little sense
+		 * to vote for a value that's below the lower threshold, so let's not do so.
+		 */
+		if (bucket == QCOM_ICC_BUCKET_WAKE && qp->keep_alive)
+			rate = max(ICC_BUS_CLK_MIN_RATE, rate);
+
 		if (qp->bus_clk_rate[i] == rate)
 			continue;
 
@@ -453,6 +462,7 @@ int qnoc_probe(struct platform_device *pdev)
 	for (i = 0; i < qp->num_bus_clks; i++)
 		qp->bus_clks[i].id = bus_clocks[i];
 
+	qp->keep_alive = desc->keep_alive;
 	qp->type = desc->type;
 	qp->qos_offset = desc->qos_offset;
 
diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index ee705edf19dd..d2c04c400cad 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -33,6 +33,7 @@ enum qcom_icc_type {
  * @bus_clk_rate: bus clock rate in Hz
  * @bus_clks: the clk_bulk_data table of bus clocks
  * @intf_clks: a clk_bulk_data array of interface clocks
+ * @keep_alive: whether to always keep a minimum vote on the bus clocks
  * @is_on: whether the bus is powered on
  */
 struct qcom_icc_provider {
@@ -45,6 +46,7 @@ struct qcom_icc_provider {
 	u64 bus_clk_rate[NUM_BUS_CLKS];
 	struct clk_bulk_data bus_clks[NUM_BUS_CLKS];
 	struct clk_bulk_data *intf_clks;
+	bool keep_alive;
 	bool is_on;
 };
 
@@ -102,6 +104,7 @@ struct qcom_icc_desc {
 	const char * const *bus_clocks;
 	const char * const *intf_clocks;
 	size_t num_intf_clocks;
+	bool keep_alive;
 	bool no_clk_scaling;
 	enum qcom_icc_type type;
 	const struct regmap_config *regmap_cfg;

-- 
2.41.0

[PATCH v5 07/22] interconnect: qcom: Fold smd-rpm.h into icc-rpm.h

[Konrad Dybcio]

smd-rpm.h is not very useful as-is and both files are always included
anyway.. Combine them.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c |  1 -
 drivers/interconnect/qcom/icc-rpm.h |  5 +++++
 drivers/interconnect/qcom/msm8916.c |  1 -
 drivers/interconnect/qcom/msm8939.c |  1 -
 drivers/interconnect/qcom/msm8974.c |  2 +-
 drivers/interconnect/qcom/msm8996.c |  1 -
 drivers/interconnect/qcom/qcm2290.c |  1 -
 drivers/interconnect/qcom/qcs404.c  |  1 -
 drivers/interconnect/qcom/sdm660.c  |  1 -
 drivers/interconnect/qcom/smd-rpm.c |  2 +-
 drivers/interconnect/qcom/smd-rpm.h | 15 ---------------
 11 files changed, 7 insertions(+), 24 deletions(-)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index 863e8ba1daa2..b8ecf9538ab9 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -14,7 +14,6 @@
 #include <linux/regmap.h>
 #include <linux/slab.h>
 
-#include "smd-rpm.h"
 #include "icc-common.h"
 #include "icc-rpm.h"
 
diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index d2c04c400cad..9ec90e13bfbd 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -6,6 +6,8 @@
 #ifndef __DRIVERS_INTERCONNECT_QCOM_ICC_RPM_H
 #define __DRIVERS_INTERCONNECT_QCOM_ICC_RPM_H
 
+#include <linux/soc/qcom/smd-rpm.h>
+
 #include <dt-bindings/interconnect/qcom,icc.h>
 
 #define RPM_BUS_MASTER_REQ	0x73616d62
@@ -121,4 +123,7 @@ enum qos_mode {
 int qnoc_probe(struct platform_device *pdev);
 int qnoc_remove(struct platform_device *pdev);
 
+bool qcom_icc_rpm_smd_available(void);
+int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val);
+
 #endif
diff --git a/drivers/interconnect/qcom/msm8916.c b/drivers/interconnect/qcom/msm8916.c
index 5c4ba2f37c8e..196b05879896 100644
--- a/drivers/interconnect/qcom/msm8916.c
+++ b/drivers/interconnect/qcom/msm8916.c
@@ -15,7 +15,6 @@
 
 #include <dt-bindings/interconnect/qcom,msm8916.h>
 
-#include "smd-rpm.h"
 #include "icc-rpm.h"
 
 enum {
diff --git a/drivers/interconnect/qcom/msm8939.c b/drivers/interconnect/qcom/msm8939.c
index caf0aefad668..639566dce45a 100644
--- a/drivers/interconnect/qcom/msm8939.c
+++ b/drivers/interconnect/qcom/msm8939.c
@@ -16,7 +16,6 @@
 
 #include <dt-bindings/interconnect/qcom,msm8939.h>
 
-#include "smd-rpm.h"
 #include "icc-rpm.h"
 
 enum {
diff --git a/drivers/interconnect/qcom/msm8974.c b/drivers/interconnect/qcom/msm8974.c
index 1828deaca443..968162213d40 100644
--- a/drivers/interconnect/qcom/msm8974.c
+++ b/drivers/interconnect/qcom/msm8974.c
@@ -38,7 +38,7 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 
-#include "smd-rpm.h"
+#include "icc-rpm.h"
 
 enum {
 	MSM8974_BIMC_MAS_AMPSS_M0 = 1,
diff --git a/drivers/interconnect/qcom/msm8996.c b/drivers/interconnect/qcom/msm8996.c
index 20340fb62fe6..1f7e88a37acd 100644
--- a/drivers/interconnect/qcom/msm8996.c
+++ b/drivers/interconnect/qcom/msm8996.c
@@ -18,7 +18,6 @@
 #include <dt-bindings/interconnect/qcom,msm8996.h>
 
 #include "icc-rpm.h"
-#include "smd-rpm.h"
 #include "msm8996.h"
 
 static const char * const mm_intf_clocks[] = {
diff --git a/drivers/interconnect/qcom/qcm2290.c b/drivers/interconnect/qcom/qcm2290.c
index a29cdb4fac03..cb636e67a5a4 100644
--- a/drivers/interconnect/qcom/qcm2290.c
+++ b/drivers/interconnect/qcom/qcm2290.c
@@ -19,7 +19,6 @@
 #include <linux/slab.h>
 
 #include "icc-rpm.h"
-#include "smd-rpm.h"
 
 enum {
 	QCM2290_MASTER_APPSS_PROC = 1,
diff --git a/drivers/interconnect/qcom/qcs404.c b/drivers/interconnect/qcom/qcs404.c
index fae155344332..938283ddd0e3 100644
--- a/drivers/interconnect/qcom/qcs404.c
+++ b/drivers/interconnect/qcom/qcs404.c
@@ -13,7 +13,6 @@
 #include <linux/of_device.h>
 
 
-#include "smd-rpm.h"
 #include "icc-rpm.h"
 
 enum {
diff --git a/drivers/interconnect/qcom/sdm660.c b/drivers/interconnect/qcom/sdm660.c
index 7ffaf70d62d3..003fc7d110a7 100644
--- a/drivers/interconnect/qcom/sdm660.c
+++ b/drivers/interconnect/qcom/sdm660.c
@@ -17,7 +17,6 @@
 #include <linux/slab.h>
 
 #include "icc-rpm.h"
-#include "smd-rpm.h"
 
 enum {
 	SDM660_MASTER_IPA = 1,
diff --git a/drivers/interconnect/qcom/smd-rpm.c b/drivers/interconnect/qcom/smd-rpm.c
index dc8ff8d133a9..b0183262ba66 100644
--- a/drivers/interconnect/qcom/smd-rpm.c
+++ b/drivers/interconnect/qcom/smd-rpm.c
@@ -13,7 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/soc/qcom/smd-rpm.h>
 
-#include "smd-rpm.h"
+#include "icc-rpm.h"
 
 #define RPM_KEY_BW		0x00007762
 
diff --git a/drivers/interconnect/qcom/smd-rpm.h b/drivers/interconnect/qcom/smd-rpm.h
deleted file mode 100644
index ca9d0327b8ac..000000000000
--- a/drivers/interconnect/qcom/smd-rpm.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2019, Linaro Ltd.
- * Author: Georgi Djakov <georgi.djakov@linaro.org>
- */
-
-#ifndef __DRIVERS_INTERCONNECT_QCOM_SMD_RPM_H
-#define __DRIVERS_INTERCONNECT_QCOM_SMD_RPM_H
-
-#include <linux/soc/qcom/smd-rpm.h>
-
-bool qcom_icc_rpm_smd_available(void);
-int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val);
-
-#endif

-- 
2.41.0

[PATCH v5 08/22] interconnect: qcom: smd-rpm: Add rpmcc handling skeleton code

[Konrad Dybcio]

Introduce qcom_icc_rpm_set_bus_rate() in preparation for handling RPM
clock resources within the interconnect framework. This lets us greatly
simplify all of the code handling, as setting the rate comes down to:

u32 rate_khz = max(clk.sleep_rate, clk.active_rate, clk_a.active_rate)
write_to_rpm(clock.description, rate_khz);

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.h | 15 +++++++++++++++
 drivers/interconnect/qcom/smd-rpm.c | 21 +++++++++++++++++++++
 2 files changed, 36 insertions(+)

diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index 9ec90e13bfbd..d857fb1efb75 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -22,6 +22,18 @@ enum qcom_icc_type {
 	QCOM_ICC_QNOC,
 };
 
+/**
+ * struct rpm_clk_resource - RPM bus clock resource
+ * @resource_type: RPM resource type of the clock resource
+ * @clock_id: index of the clock resource of a specific resource type
+ * @branch: whether the resource represents a branch clock
+*/
+struct rpm_clk_resource {
+	u32 resource_type;
+	u32 clock_id;
+	bool branch;
+};
+
 #define NUM_BUS_CLKS	2
 
 /**
@@ -47,6 +59,7 @@ struct qcom_icc_provider {
 	unsigned int qos_offset;
 	u64 bus_clk_rate[NUM_BUS_CLKS];
 	struct clk_bulk_data bus_clks[NUM_BUS_CLKS];
+	const struct rpm_clk_resource *bus_clk_desc;
 	struct clk_bulk_data *intf_clks;
 	bool keep_alive;
 	bool is_on;
@@ -104,6 +117,7 @@ struct qcom_icc_desc {
 	struct qcom_icc_node * const *nodes;
 	size_t num_nodes;
 	const char * const *bus_clocks;
+	const struct rpm_clk_resource *bus_clk_desc;
 	const char * const *intf_clocks;
 	size_t num_intf_clocks;
 	bool keep_alive;
@@ -125,5 +139,6 @@ int qnoc_remove(struct platform_device *pdev);
 
 bool qcom_icc_rpm_smd_available(void);
 int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val);
+int qcom_icc_rpm_set_bus_rate(const struct rpm_clk_resource *clk, int rsc_type, u32 rate);
 
 #endif
diff --git a/drivers/interconnect/qcom/smd-rpm.c b/drivers/interconnect/qcom/smd-rpm.c
index b0183262ba66..b06374340eeb 100644
--- a/drivers/interconnect/qcom/smd-rpm.c
+++ b/drivers/interconnect/qcom/smd-rpm.c
@@ -16,6 +16,7 @@
 #include "icc-rpm.h"
 
 #define RPM_KEY_BW		0x00007762
+#define QCOM_RPM_SMD_KEY_RATE	0x007a484b
 
 static struct qcom_smd_rpm *icc_smd_rpm;
 
@@ -44,6 +45,26 @@ int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val)
 }
 EXPORT_SYMBOL_GPL(qcom_icc_rpm_smd_send);
 
+int qcom_icc_rpm_set_bus_rate(const struct rpm_clk_resource *clk, int rsc_type, u32 rate)
+{
+	struct clk_smd_rpm_req req = {
+		.key = cpu_to_le32(QCOM_RPM_SMD_KEY_RATE),
+		.nbytes = cpu_to_le32(sizeof(u32)),
+	};
+
+	/* Branch clocks are only on/off */
+	if (clk->branch)
+		rate = !!rate;
+
+	req.value = cpu_to_le32(rate);
+	return qcom_rpm_smd_write(icc_smd_rpm,
+				  rsc_type,
+				  clk->resource_type,
+				  clk->clock_id,
+				  &req, sizeof(req));
+}
+EXPORT_SYMBOL_GPL(qcom_icc_rpm_set_bus_rate);
+
 static int qcom_icc_rpm_smd_remove(struct platform_device *pdev)
 {
 	icc_smd_rpm = NULL;

-- 
2.41.0

Re: [PATCH v5 08/22] interconnect: qcom: smd-rpm: Add rpmcc handling skeleton code

[Stephan Gerhold]

On Wed, Jun 14, 2023 at 12:22:19PM +0200, Konrad Dybcio wrote:
> Introduce qcom_icc_rpm_set_bus_rate() in preparation for handling RPM
> clock resources within the interconnect framework. This lets us greatly
> simplify all of the code handling, as setting the rate comes down to:
> 
> u32 rate_khz = max(clk.sleep_rate, clk.active_rate, clk_a.active_rate)
> write_to_rpm(clock.description, rate_khz);
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  drivers/interconnect/qcom/icc-rpm.h | 15 +++++++++++++++
>  drivers/interconnect/qcom/smd-rpm.c | 21 +++++++++++++++++++++
>  2 files changed, 36 insertions(+)
> 
> diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
> index 9ec90e13bfbd..d857fb1efb75 100644
> --- a/drivers/interconnect/qcom/icc-rpm.h
> +++ b/drivers/interconnect/qcom/icc-rpm.h
> @@ -22,6 +22,18 @@ enum qcom_icc_type {
>  	QCOM_ICC_QNOC,
>  };
>  
> +/**
> + * struct rpm_clk_resource - RPM bus clock resource
> + * @resource_type: RPM resource type of the clock resource
> + * @clock_id: index of the clock resource of a specific resource type
> + * @branch: whether the resource represents a branch clock
> +*/
> +struct rpm_clk_resource {
> +	u32 resource_type;
> +	u32 clock_id;
> +	bool branch;
> +};
> +
>  #define NUM_BUS_CLKS	2
>  
>  /**
> @@ -47,6 +59,7 @@ struct qcom_icc_provider {
>  	unsigned int qos_offset;
>  	u64 bus_clk_rate[NUM_BUS_CLKS];
>  	struct clk_bulk_data bus_clks[NUM_BUS_CLKS];
> +	const struct rpm_clk_resource *bus_clk_desc;
>  	struct clk_bulk_data *intf_clks;
>  	bool keep_alive;
>  	bool is_on;
> @@ -104,6 +117,7 @@ struct qcom_icc_desc {
>  	struct qcom_icc_node * const *nodes;
>  	size_t num_nodes;
>  	const char * const *bus_clocks;
> +	const struct rpm_clk_resource *bus_clk_desc;
>  	const char * const *intf_clocks;
>  	size_t num_intf_clocks;
>  	bool keep_alive;
> @@ -125,5 +139,6 @@ int qnoc_remove(struct platform_device *pdev);
>  
>  bool qcom_icc_rpm_smd_available(void);
>  int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val);
> +int qcom_icc_rpm_set_bus_rate(const struct rpm_clk_resource *clk, int rsc_type, u32 rate);
>  
>  #endif
> diff --git a/drivers/interconnect/qcom/smd-rpm.c b/drivers/interconnect/qcom/smd-rpm.c
> index b0183262ba66..b06374340eeb 100644
> --- a/drivers/interconnect/qcom/smd-rpm.c
> +++ b/drivers/interconnect/qcom/smd-rpm.c
> @@ -16,6 +16,7 @@
>  #include "icc-rpm.h"
>  
>  #define RPM_KEY_BW		0x00007762
> +#define QCOM_RPM_SMD_KEY_RATE	0x007a484b
>  
>  static struct qcom_smd_rpm *icc_smd_rpm;
>  
> @@ -44,6 +45,26 @@ int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val)
>  }
>  EXPORT_SYMBOL_GPL(qcom_icc_rpm_smd_send);
>  
> +int qcom_icc_rpm_set_bus_rate(const struct rpm_clk_resource *clk, int rsc_type, u32 rate)
> +{
> +	struct clk_smd_rpm_req req = {
> +		.key = cpu_to_le32(QCOM_RPM_SMD_KEY_RATE),
> +		.nbytes = cpu_to_le32(sizeof(u32)),
> +	};
> +
> +	/* Branch clocks are only on/off */
> +	if (clk->branch)
> +		rate = !!rate;
> +
> +	req.value = cpu_to_le32(rate);
> +	return qcom_rpm_smd_write(icc_smd_rpm,
> +				  rsc_type,
> +				  clk->resource_type,

Sorry to have more minor comments but as you can see here the resource
type is taken from the rpm_clk_resource. The parameter that you are
describing as "rsc_type" is actually the "ctx" in the other function. :')

If you fix this feel free to add my:

Reviewed-by: Stephan Gerhold <stephan@gerhold.net>

Thanks,
Stephan

Re: [PATCH v5 08/22] interconnect: qcom: smd-rpm: Add rpmcc handling skeleton code

[Konrad Dybcio]

On 14.06.2023 16:47, Stephan Gerhold wrote:
> On Wed, Jun 14, 2023 at 12:22:19PM +0200, Konrad Dybcio wrote:
>> Introduce qcom_icc_rpm_set_bus_rate() in preparation for handling RPM
>> clock resources within the interconnect framework. This lets us greatly
>> simplify all of the code handling, as setting the rate comes down to:
>>
>> u32 rate_khz = max(clk.sleep_rate, clk.active_rate, clk_a.active_rate)
>> write_to_rpm(clock.description, rate_khz);
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>>  drivers/interconnect/qcom/icc-rpm.h | 15 +++++++++++++++
>>  drivers/interconnect/qcom/smd-rpm.c | 21 +++++++++++++++++++++
>>  2 files changed, 36 insertions(+)
>>
>> diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
>> index 9ec90e13bfbd..d857fb1efb75 100644
>> --- a/drivers/interconnect/qcom/icc-rpm.h
>> +++ b/drivers/interconnect/qcom/icc-rpm.h
>> @@ -22,6 +22,18 @@ enum qcom_icc_type {
>>  	QCOM_ICC_QNOC,
>>  };
>>  
>> +/**
>> + * struct rpm_clk_resource - RPM bus clock resource
>> + * @resource_type: RPM resource type of the clock resource
>> + * @clock_id: index of the clock resource of a specific resource type
>> + * @branch: whether the resource represents a branch clock
>> +*/
>> +struct rpm_clk_resource {
>> +	u32 resource_type;
>> +	u32 clock_id;
>> +	bool branch;
>> +};
>> +
>>  #define NUM_BUS_CLKS	2
>>  
>>  /**
>> @@ -47,6 +59,7 @@ struct qcom_icc_provider {
>>  	unsigned int qos_offset;
>>  	u64 bus_clk_rate[NUM_BUS_CLKS];
>>  	struct clk_bulk_data bus_clks[NUM_BUS_CLKS];
>> +	const struct rpm_clk_resource *bus_clk_desc;
>>  	struct clk_bulk_data *intf_clks;
>>  	bool keep_alive;
>>  	bool is_on;
>> @@ -104,6 +117,7 @@ struct qcom_icc_desc {
>>  	struct qcom_icc_node * const *nodes;
>>  	size_t num_nodes;
>>  	const char * const *bus_clocks;
>> +	const struct rpm_clk_resource *bus_clk_desc;
>>  	const char * const *intf_clocks;
>>  	size_t num_intf_clocks;
>>  	bool keep_alive;
>> @@ -125,5 +139,6 @@ int qnoc_remove(struct platform_device *pdev);
>>  
>>  bool qcom_icc_rpm_smd_available(void);
>>  int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val);
>> +int qcom_icc_rpm_set_bus_rate(const struct rpm_clk_resource *clk, int rsc_type, u32 rate);
>>  
>>  #endif
>> diff --git a/drivers/interconnect/qcom/smd-rpm.c b/drivers/interconnect/qcom/smd-rpm.c
>> index b0183262ba66..b06374340eeb 100644
>> --- a/drivers/interconnect/qcom/smd-rpm.c
>> +++ b/drivers/interconnect/qcom/smd-rpm.c
>> @@ -16,6 +16,7 @@
>>  #include "icc-rpm.h"
>>  
>>  #define RPM_KEY_BW		0x00007762
>> +#define QCOM_RPM_SMD_KEY_RATE	0x007a484b
>>  
>>  static struct qcom_smd_rpm *icc_smd_rpm;
>>  
>> @@ -44,6 +45,26 @@ int qcom_icc_rpm_smd_send(int ctx, int rsc_type, int id, u32 val)
>>  }
>>  EXPORT_SYMBOL_GPL(qcom_icc_rpm_smd_send);
>>  
>> +int qcom_icc_rpm_set_bus_rate(const struct rpm_clk_resource *clk, int rsc_type, u32 rate)
>> +{
>> +	struct clk_smd_rpm_req req = {
>> +		.key = cpu_to_le32(QCOM_RPM_SMD_KEY_RATE),
>> +		.nbytes = cpu_to_le32(sizeof(u32)),
>> +	};
>> +
>> +	/* Branch clocks are only on/off */
>> +	if (clk->branch)
>> +		rate = !!rate;
>> +
>> +	req.value = cpu_to_le32(rate);
>> +	return qcom_rpm_smd_write(icc_smd_rpm,
>> +				  rsc_type,
>> +				  clk->resource_type,
> 
> Sorry to have more minor comments but as you can see here the resource
> type is taken from the rpm_clk_resource. The parameter that you are
> describing as "rsc_type" is actually the "ctx" in the other function. :')
Meh I fixed it too fast.. thanks

Konrad
> 
> If you fix this feel free to add my:
> 
> Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
> 
> Thanks,
> Stephan

[PATCH v5 09/22] interconnect: qcom: Add missing headers in icc-rpm.h

[Konrad Dybcio]

Currently the header does not provide all the required dependencies.
Fix it.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index d857fb1efb75..0355e0250ccc 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -6,6 +6,8 @@
 #ifndef __DRIVERS_INTERCONNECT_QCOM_ICC_RPM_H
 #define __DRIVERS_INTERCONNECT_QCOM_ICC_RPM_H
 
+#include <linux/interconnect-provider.h>
+#include <linux/platform_device.h>
 #include <linux/soc/qcom/smd-rpm.h>
 
 #include <dt-bindings/interconnect/qcom,icc.h>

-- 
2.41.0

[PATCH v5 10/22] interconnect: qcom: Define RPM bus clocks

[Konrad Dybcio]

Add the definitions for RPM bus clocks that will be used by many
different platforms.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/Makefile         |  2 +-
 drivers/interconnect/qcom/icc-rpm-clocks.c | 77 ++++++++++++++++++++++++++++++
 drivers/interconnect/qcom/icc-rpm.h        | 13 +++++
 3 files changed, 91 insertions(+), 1 deletion(-)

diff --git a/drivers/interconnect/qcom/Makefile b/drivers/interconnect/qcom/Makefile
index ab988926433c..80d9d2da95d1 100644
--- a/drivers/interconnect/qcom/Makefile
+++ b/drivers/interconnect/qcom/Makefile
@@ -29,7 +29,7 @@ qnoc-sm8250-objs			:= sm8250.o
 qnoc-sm8350-objs			:= sm8350.o
 qnoc-sm8450-objs			:= sm8450.o
 qnoc-sm8550-objs			:= sm8550.o
-icc-smd-rpm-objs			:= smd-rpm.o icc-rpm.o
+icc-smd-rpm-objs			:= smd-rpm.o icc-rpm.o icc-rpm-clocks.o
 
 obj-$(CONFIG_INTERCONNECT_QCOM_BCM_VOTER) += icc-bcm-voter.o
 obj-$(CONFIG_INTERCONNECT_QCOM_MSM8916) += qnoc-msm8916.o
diff --git a/drivers/interconnect/qcom/icc-rpm-clocks.c b/drivers/interconnect/qcom/icc-rpm-clocks.c
new file mode 100644
index 000000000000..63c82a91bbc7
--- /dev/null
+++ b/drivers/interconnect/qcom/icc-rpm-clocks.c
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2023 Linaro Ltd
+ */
+
+#include <linux/soc/qcom/smd-rpm.h>
+
+#include "icc-rpm.h"
+
+const struct rpm_clk_resource aggre1_clk = {
+	.resource_type = QCOM_SMD_RPM_AGGR_CLK,
+	.clock_id = 1,
+};
+EXPORT_SYMBOL_GPL(aggre1_clk);
+
+const struct rpm_clk_resource aggre2_clk = {
+	.resource_type = QCOM_SMD_RPM_AGGR_CLK,
+	.clock_id = 2,
+};
+EXPORT_SYMBOL_GPL(aggre2_clk);
+
+const struct rpm_clk_resource bimc_clk = {
+	.resource_type = QCOM_SMD_RPM_MEM_CLK,
+	.clock_id = 0,
+};
+EXPORT_SYMBOL_GPL(bimc_clk);
+
+const struct rpm_clk_resource bus_0_clk = {
+	.resource_type = QCOM_SMD_RPM_BUS_CLK,
+	.clock_id = 0,
+};
+EXPORT_SYMBOL_GPL(bus_0_clk);
+
+const struct rpm_clk_resource bus_1_clk = {
+	.resource_type = QCOM_SMD_RPM_BUS_CLK,
+	.clock_id = 1,
+};
+EXPORT_SYMBOL_GPL(bus_1_clk);
+
+const struct rpm_clk_resource bus_2_clk = {
+	.resource_type = QCOM_SMD_RPM_BUS_CLK,
+	.clock_id = 2,
+};
+EXPORT_SYMBOL_GPL(bus_2_clk);
+
+const struct rpm_clk_resource mmaxi_0_clk = {
+	.resource_type = QCOM_SMD_RPM_MMAXI_CLK,
+	.clock_id = 0,
+};
+EXPORT_SYMBOL_GPL(mmaxi_0_clk);
+
+const struct rpm_clk_resource mmaxi_1_clk = {
+	.resource_type = QCOM_SMD_RPM_MMAXI_CLK,
+	.clock_id = 1,
+};
+EXPORT_SYMBOL_GPL(mmaxi_1_clk);
+
+const struct rpm_clk_resource qup_clk = {
+	.resource_type = QCOM_SMD_RPM_QUP_CLK,
+	.clock_id = 0,
+};
+EXPORT_SYMBOL_GPL(qup_clk);
+
+/* Branch clocks */
+const struct rpm_clk_resource aggre1_branch_clk = {
+	.resource_type = QCOM_SMD_RPM_AGGR_CLK,
+	.clock_id = 1,
+	.branch = true,
+};
+EXPORT_SYMBOL_GPL(aggre1_branch_clk);
+
+const struct rpm_clk_resource aggre2_branch_clk = {
+	.resource_type = QCOM_SMD_RPM_AGGR_CLK,
+	.clock_id = 2,
+	.branch = true,
+};
+EXPORT_SYMBOL_GPL(aggre2_branch_clk);
diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index 0355e0250ccc..692d91c248d9 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -136,6 +136,19 @@ enum qos_mode {
 	NOC_QOS_MODE_BYPASS,
 };
 
+extern const struct rpm_clk_resource aggre1_clk;
+extern const struct rpm_clk_resource aggre2_clk;
+extern const struct rpm_clk_resource bimc_clk;
+extern const struct rpm_clk_resource bus_0_clk;
+extern const struct rpm_clk_resource bus_1_clk;
+extern const struct rpm_clk_resource bus_2_clk;
+extern const struct rpm_clk_resource mmaxi_0_clk;
+extern const struct rpm_clk_resource mmaxi_1_clk;
+extern const struct rpm_clk_resource qup_clk;
+
+extern const struct rpm_clk_resource aggre1_branch_clk;
+extern const struct rpm_clk_resource aggre2_branch_clk;
+
 int qnoc_probe(struct platform_device *pdev);
 int qnoc_remove(struct platform_device *pdev);
 

-- 
2.41.0

[PATCH v5 11/22] interconnect: qcom: sdm660: Hook up RPM bus clk definitions

[Konrad Dybcio]

Assign the necessary definitions to migrate to the new bus clock
handling mechanism.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/sdm660.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/interconnect/qcom/sdm660.c b/drivers/interconnect/qcom/sdm660.c
index 003fc7d110a7..5743ed680e8e 100644
--- a/drivers/interconnect/qcom/sdm660.c
+++ b/drivers/interconnect/qcom/sdm660.c
@@ -1511,6 +1511,7 @@ static const struct qcom_icc_desc sdm660_a2noc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = sdm660_a2noc_nodes,
 	.num_nodes = ARRAY_SIZE(sdm660_a2noc_nodes),
+	.bus_clk_desc = &aggre2_clk,
 	.intf_clocks = a2noc_intf_clocks,
 	.num_intf_clocks = ARRAY_SIZE(a2noc_intf_clocks),
 	.regmap_cfg = &sdm660_a2noc_regmap_config,
@@ -1539,6 +1540,7 @@ static const struct qcom_icc_desc sdm660_bimc = {
 	.type = QCOM_ICC_BIMC,
 	.nodes = sdm660_bimc_nodes,
 	.num_nodes = ARRAY_SIZE(sdm660_bimc_nodes),
+	.bus_clk_desc = &bimc_clk,
 	.regmap_cfg = &sdm660_bimc_regmap_config,
 };
 
@@ -1593,6 +1595,7 @@ static const struct qcom_icc_desc sdm660_cnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = sdm660_cnoc_nodes,
 	.num_nodes = ARRAY_SIZE(sdm660_cnoc_nodes),
+	.bus_clk_desc = &bus_2_clk,
 	.regmap_cfg = &sdm660_cnoc_regmap_config,
 };
 
@@ -1655,6 +1658,7 @@ static const struct qcom_icc_desc sdm660_mnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = sdm660_mnoc_nodes,
 	.num_nodes = ARRAY_SIZE(sdm660_mnoc_nodes),
+	.bus_clk_desc = &mmaxi_0_clk,
 	.intf_clocks = mm_intf_clocks,
 	.num_intf_clocks = ARRAY_SIZE(mm_intf_clocks),
 	.regmap_cfg = &sdm660_mnoc_regmap_config,
@@ -1692,6 +1696,7 @@ static const struct qcom_icc_desc sdm660_snoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = sdm660_snoc_nodes,
 	.num_nodes = ARRAY_SIZE(sdm660_snoc_nodes),
+	.bus_clk_desc = &bus_1_clk,
 	.regmap_cfg = &sdm660_snoc_regmap_config,
 };
 

-- 
2.41.0

[PATCH v5 12/22] interconnect: qcom: msm8996: Hook up RPM bus clk definitions

[Konrad Dybcio]

Assign the necessary definitions to migrate to the new bus clock
handling mechanism.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/msm8996.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/interconnect/qcom/msm8996.c b/drivers/interconnect/qcom/msm8996.c
index 1f7e88a37acd..a596f4035d2e 100644
--- a/drivers/interconnect/qcom/msm8996.c
+++ b/drivers/interconnect/qcom/msm8996.c
@@ -1840,6 +1840,7 @@ static const struct qcom_icc_desc msm8996_a1noc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = a1noc_nodes,
 	.num_nodes = ARRAY_SIZE(a1noc_nodes),
+	.bus_clk_desc = &aggre1_branch_clk,
 	.regmap_cfg = &msm8996_a1noc_regmap_config
 };
 
@@ -1861,6 +1862,7 @@ static const struct qcom_icc_desc msm8996_a2noc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = a2noc_nodes,
 	.num_nodes = ARRAY_SIZE(a2noc_nodes),
+	.bus_clk_desc = &aggre2_branch_clk,
 	.intf_clocks = a2noc_intf_clocks,
 	.num_intf_clocks = ARRAY_SIZE(a2noc_intf_clocks),
 	.regmap_cfg = &msm8996_a2noc_regmap_config
@@ -1889,6 +1891,7 @@ static const struct qcom_icc_desc msm8996_bimc = {
 	.type = QCOM_ICC_BIMC,
 	.nodes = bimc_nodes,
 	.num_nodes = ARRAY_SIZE(bimc_nodes),
+	.bus_clk_desc = &bimc_clk,
 	.regmap_cfg = &msm8996_bimc_regmap_config
 };
 
@@ -1947,6 +1950,7 @@ static const struct qcom_icc_desc msm8996_cnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = cnoc_nodes,
 	.num_nodes = ARRAY_SIZE(cnoc_nodes),
+	.bus_clk_desc = &bus_2_clk,
 	.regmap_cfg = &msm8996_cnoc_regmap_config
 };
 
@@ -2000,6 +2004,7 @@ static const struct qcom_icc_desc msm8996_mnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = mnoc_nodes,
 	.num_nodes = ARRAY_SIZE(mnoc_nodes),
+	.bus_clk_desc = &mmaxi_0_clk,
 	.intf_clocks = mm_intf_clocks,
 	.num_intf_clocks = ARRAY_SIZE(mm_intf_clocks),
 	.regmap_cfg = &msm8996_mnoc_regmap_config
@@ -2038,6 +2043,7 @@ static const struct qcom_icc_desc msm8996_pnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = pnoc_nodes,
 	.num_nodes = ARRAY_SIZE(pnoc_nodes),
+	.bus_clk_desc = &bus_0_clk,
 	.regmap_cfg = &msm8996_pnoc_regmap_config
 };
 
@@ -2082,6 +2088,7 @@ static const struct qcom_icc_desc msm8996_snoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = snoc_nodes,
 	.num_nodes = ARRAY_SIZE(snoc_nodes),
+	.bus_clk_desc = &bus_1_clk,
 	.regmap_cfg = &msm8996_snoc_regmap_config
 };
 

-- 
2.41.0

[PATCH v5 13/22] interconnect: qcom: qcs404: Hook up RPM bus clk definitions

[Konrad Dybcio]

Assign the necessary definitions to migrate to the new bus clock
handling mechanism.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/qcs404.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/interconnect/qcom/qcs404.c b/drivers/interconnect/qcom/qcs404.c
index 938283ddd0e3..9deb4d81104e 100644
--- a/drivers/interconnect/qcom/qcs404.c
+++ b/drivers/interconnect/qcom/qcs404.c
@@ -984,6 +984,7 @@ static struct qcom_icc_node * const qcs404_bimc_nodes[] = {
 };
 
 static const struct qcom_icc_desc qcs404_bimc = {
+	.bus_clk_desc = &bimc_clk,
 	.nodes = qcs404_bimc_nodes,
 	.num_nodes = ARRAY_SIZE(qcs404_bimc_nodes),
 };
@@ -1038,6 +1039,7 @@ static struct qcom_icc_node * const qcs404_pcnoc_nodes[] = {
 };
 
 static const struct qcom_icc_desc qcs404_pcnoc = {
+	.bus_clk_desc = &bus_0_clk,
 	.nodes = qcs404_pcnoc_nodes,
 	.num_nodes = ARRAY_SIZE(qcs404_pcnoc_nodes),
 };
@@ -1066,6 +1068,7 @@ static struct qcom_icc_node * const qcs404_snoc_nodes[] = {
 };
 
 static const struct qcom_icc_desc qcs404_snoc = {
+	.bus_clk_desc = &bus_1_clk,
 	.nodes = qcs404_snoc_nodes,
 	.num_nodes = ARRAY_SIZE(qcs404_snoc_nodes),
 };

-- 
2.41.0

[PATCH v5 14/22] interconnect: qcom: msm8939: Hook up RPM bus clk definitions

[Konrad Dybcio]

Assign the necessary definitions to migrate to the new bus clock
handling mechanism.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/msm8939.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/interconnect/qcom/msm8939.c b/drivers/interconnect/qcom/msm8939.c
index 639566dce45a..94b11b590a8e 100644
--- a/drivers/interconnect/qcom/msm8939.c
+++ b/drivers/interconnect/qcom/msm8939.c
@@ -1284,6 +1284,7 @@ static const struct qcom_icc_desc msm8939_snoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = msm8939_snoc_nodes,
 	.num_nodes = ARRAY_SIZE(msm8939_snoc_nodes),
+	.bus_clk_desc = &bus_1_clk,
 	.regmap_cfg = &msm8939_snoc_regmap_config,
 	.qos_offset = 0x7000,
 };
@@ -1304,6 +1305,7 @@ static const struct qcom_icc_desc msm8939_snoc_mm = {
 	.type = QCOM_ICC_NOC,
 	.nodes = msm8939_snoc_mm_nodes,
 	.num_nodes = ARRAY_SIZE(msm8939_snoc_mm_nodes),
+	.bus_clk_desc = &bus_2_clk,
 	.regmap_cfg = &msm8939_snoc_regmap_config,
 	.qos_offset = 0x7000,
 };
@@ -1332,6 +1334,7 @@ static const struct qcom_icc_desc msm8939_bimc = {
 	.type = QCOM_ICC_BIMC,
 	.nodes = msm8939_bimc_nodes,
 	.num_nodes = ARRAY_SIZE(msm8939_bimc_nodes),
+	.bus_clk_desc = &bimc_clk,
 	.regmap_cfg = &msm8939_bimc_regmap_config,
 	.qos_offset = 0x8000,
 };
@@ -1403,6 +1406,7 @@ static const struct qcom_icc_desc msm8939_pcnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = msm8939_pcnoc_nodes,
 	.num_nodes = ARRAY_SIZE(msm8939_pcnoc_nodes),
+	.bus_clk_desc = &bus_0_clk,
 	.regmap_cfg = &msm8939_pcnoc_regmap_config,
 	.qos_offset = 0x7000,
 };

-- 
2.41.0

[PATCH v5 15/22] interconnect: qcom: msm8916: Hook up RPM bus clk definitions

[Konrad Dybcio]

Assign the necessary definitions to migrate to the new bus clock
handling mechanism.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/msm8916.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/interconnect/qcom/msm8916.c b/drivers/interconnect/qcom/msm8916.c
index 196b05879896..be2a190a8b52 100644
--- a/drivers/interconnect/qcom/msm8916.c
+++ b/drivers/interconnect/qcom/msm8916.c
@@ -1231,6 +1231,7 @@ static const struct qcom_icc_desc msm8916_snoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = msm8916_snoc_nodes,
 	.num_nodes = ARRAY_SIZE(msm8916_snoc_nodes),
+	.bus_clk_desc = &bus_1_clk,
 	.regmap_cfg = &msm8916_snoc_regmap_config,
 	.qos_offset = 0x7000,
 };
@@ -1259,6 +1260,7 @@ static const struct qcom_icc_desc msm8916_bimc = {
 	.type = QCOM_ICC_BIMC,
 	.nodes = msm8916_bimc_nodes,
 	.num_nodes = ARRAY_SIZE(msm8916_bimc_nodes),
+	.bus_clk_desc = &bimc_clk,
 	.regmap_cfg = &msm8916_bimc_regmap_config,
 	.qos_offset = 0x8000,
 };
@@ -1328,6 +1330,7 @@ static const struct qcom_icc_desc msm8916_pcnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = msm8916_pcnoc_nodes,
 	.num_nodes = ARRAY_SIZE(msm8916_pcnoc_nodes),
+	.bus_clk_desc = &bus_0_clk,
 	.regmap_cfg = &msm8916_pcnoc_regmap_config,
 	.qos_offset = 0x7000,
 };

-- 
2.41.0

[PATCH v5 16/22] interconnect: qcom: qcm2290: Hook up RPM bus clk definitions

[Konrad Dybcio]

Assign the necessary definitions to migrate to the new bus clock
handling mechanism.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/qcm2290.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/interconnect/qcom/qcm2290.c b/drivers/interconnect/qcom/qcm2290.c
index cb636e67a5a4..2c7a76fab83c 100644
--- a/drivers/interconnect/qcom/qcm2290.c
+++ b/drivers/interconnect/qcom/qcm2290.c
@@ -1196,6 +1196,7 @@ static const struct qcom_icc_desc qcm2290_bimc = {
 	.type = QCOM_ICC_BIMC,
 	.nodes = qcm2290_bimc_nodes,
 	.num_nodes = ARRAY_SIZE(qcm2290_bimc_nodes),
+	.bus_clk_desc = &bimc_clk,
 	.regmap_cfg = &qcm2290_bimc_regmap_config,
 	/* M_REG_BASE() in vendor msm_bus_bimc_adhoc driver */
 	.qos_offset = 0x8000,
@@ -1251,6 +1252,7 @@ static const struct qcom_icc_desc qcm2290_cnoc = {
 	.type = QCOM_ICC_NOC,
 	.nodes = qcm2290_cnoc_nodes,
 	.num_nodes = ARRAY_SIZE(qcm2290_cnoc_nodes),
+	.bus_clk_desc = &bus_1_clk,
 	.regmap_cfg = &qcm2290_cnoc_regmap_config,
 };
 
@@ -1292,6 +1294,7 @@ static const struct qcom_icc_desc qcm2290_snoc = {
 	.type = QCOM_ICC_QNOC,
 	.nodes = qcm2290_snoc_nodes,
 	.num_nodes = ARRAY_SIZE(qcm2290_snoc_nodes),
+	.bus_clk_desc = &bus_2_clk,
 	.regmap_cfg = &qcm2290_snoc_regmap_config,
 	/* Vendor DT node fab-sys_noc property 'qcom,base-offset' */
 	.qos_offset = 0x15000,
@@ -1306,6 +1309,7 @@ static const struct qcom_icc_desc qcm2290_qup_virt = {
 	.type = QCOM_ICC_QNOC,
 	.nodes = qcm2290_qup_virt_nodes,
 	.num_nodes = ARRAY_SIZE(qcm2290_qup_virt_nodes),
+	.bus_clk_desc = &qup_clk,
 };
 
 static struct qcom_icc_node * const qcm2290_mmnrt_virt_nodes[] = {
@@ -1319,6 +1323,7 @@ static const struct qcom_icc_desc qcm2290_mmnrt_virt = {
 	.type = QCOM_ICC_QNOC,
 	.nodes = qcm2290_mmnrt_virt_nodes,
 	.num_nodes = ARRAY_SIZE(qcm2290_mmnrt_virt_nodes),
+	.bus_clk_desc = &mmaxi_0_clk,
 	.regmap_cfg = &qcm2290_snoc_regmap_config,
 	.qos_offset = 0x15000,
 };
@@ -1333,6 +1338,7 @@ static const struct qcom_icc_desc qcm2290_mmrt_virt = {
 	.type = QCOM_ICC_QNOC,
 	.nodes = qcm2290_mmrt_virt_nodes,
 	.num_nodes = ARRAY_SIZE(qcm2290_mmrt_virt_nodes),
+	.bus_clk_desc = &mmaxi_1_clk,
 	.regmap_cfg = &qcm2290_snoc_regmap_config,
 	.qos_offset = 0x15000,
 };

-- 
2.41.0

[PATCH v5 17/22] interconnect: qcom: icc-rpm: Control bus rpmcc from icc

[Konrad Dybcio]

The sole purpose of bus clocks that were previously registered with
rpmcc was to convey the aggregated bandwidth to RPM. There's no good
reason to keep them outside the interconnect framework, as it only
adds to the plentiful complexity.

Add the required code to handle these clocks from within SMD RPM ICC.

RPM-owned bus clocks are no longer considered a thing, but sadly we
have to allow for the existence of HLOS-owned bus clocks, as some
(mostly older) SoCs (ab)use these for bus scaling (e.g. MSM8998 and
&mmcc AHB_CLK_SRC).

This in turn is trivially solved with a single *clk, which is filled
and used iff qp.bus_clk_desc is absent and we have a "bus" clock-names
entry in the DT node.

This change should(tm) be fully compatible with all sorts of old
Device Trees as far as the interconnect functionality goes (modulo
abusing bus clock handles or wrongly using the qcom,icc.h binding,
but that's a mistake in and of itself).

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c | 121 ++++++++++++++++++++----------------
 drivers/interconnect/qcom/icc-rpm.h |  13 ++--
 drivers/interconnect/qcom/msm8996.c |   1 -
 drivers/interconnect/qcom/sdm660.c  |   1 -
 4 files changed, 73 insertions(+), 63 deletions(-)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index b8ecf9538ab9..858880a97d2a 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -49,7 +49,7 @@
 #define NOC_QOS_MODE_FIXED_VAL		0x0
 #define NOC_QOS_MODE_BYPASS_VAL		0x2
 
-#define ICC_BUS_CLK_MIN_RATE		19200000ULL
+#define ICC_BUS_CLK_MIN_RATE		19200ULL /* kHz */
 
 static int qcom_icc_set_qnoc_qos(struct icc_node *src)
 {
@@ -338,11 +338,10 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 	struct qcom_icc_node *src_qn = NULL, *dst_qn = NULL;
 	struct icc_provider *provider;
 	u64 sum_bw;
-	u64 rate;
+	u64 active_rate, sleep_rate;
 	u64 agg_avg[QCOM_ICC_NUM_BUCKETS], agg_peak[QCOM_ICC_NUM_BUCKETS];
 	u64 max_agg_avg;
-	int ret, i;
-	int bucket;
+	int ret;
 
 	src_qn = src->data;
 	if (dst)
@@ -364,49 +363,61 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 			return ret;
 	}
 
-	for (i = 0; i < qp->num_bus_clks; i++) {
-		/*
-		 * Use WAKE bucket for active clock, otherwise, use SLEEP bucket
-		 * for other clocks.  If a platform doesn't set interconnect
-		 * path tags, by default use sleep bucket for all clocks.
-		 *
-		 * Note, AMC bucket is not supported yet.
-		 */
-		if (!strcmp(qp->bus_clks[i].id, "bus_a"))
-			bucket = QCOM_ICC_BUCKET_WAKE;
-		else
-			bucket = QCOM_ICC_BUCKET_SLEEP;
-
-		rate = icc_units_to_bps(max(agg_avg[bucket], agg_peak[bucket]));
-		do_div(rate, src_qn->buswidth);
-		rate = min_t(u64, rate, LONG_MAX);
-
-		/*
-		 * Downstream checks whether the requested rate is zero, but it makes little sense
-		 * to vote for a value that's below the lower threshold, so let's not do so.
-		 */
-		if (bucket == QCOM_ICC_BUCKET_WAKE && qp->keep_alive)
-			rate = max(ICC_BUS_CLK_MIN_RATE, rate);
-
-		if (qp->bus_clk_rate[i] == rate)
-			continue;
-
-		ret = clk_set_rate(qp->bus_clks[i].clk, rate);
-		if (ret) {
-			pr_err("%s clk_set_rate error: %d\n",
-			       qp->bus_clks[i].id, ret);
+	/* Some providers don't have a bus clock to scale */
+	if (!qp->bus_clk_desc && !qp->bus_clk)
+		return 0;
+
+	/* Intentionally keep the rates in kHz as that's what RPM accepts */
+	active_rate = max(agg_avg[QCOM_SMD_RPM_ACTIVE_STATE],
+			  agg_peak[QCOM_SMD_RPM_ACTIVE_STATE]);
+	do_div(active_rate, src_qn->buswidth);
+
+	sleep_rate = max(agg_avg[QCOM_SMD_RPM_SLEEP_STATE],
+			 agg_peak[QCOM_SMD_RPM_SLEEP_STATE]);
+	do_div(sleep_rate, src_qn->buswidth);
+
+	/*
+	 * Downstream checks whether the requested rate is zero, but it makes little sense
+	 * to vote for a value that's below the lower threshold, so let's not do so.
+	 */
+	if (qp->keep_alive)
+		active_rate = max(ICC_BUS_CLK_MIN_RATE, active_rate);
+
+	/* Some providers have a non-RPM-owned bus clock - convert kHz->Hz for the CCF */
+	if (qp->bus_clk) {
+		active_rate = max_t(u64, active_rate, sleep_rate);
+		/* ARM32 caps clk_set_rate arg to u32.. Nothing we can do about that! */
+		active_rate = min_t(u64, 1000ULL * active_rate, ULONG_MAX);
+		return clk_set_rate(qp->bus_clk, active_rate);
+	}
+
+	/* RPM only accepts <=INT_MAX rates */
+	active_rate = min_t(u64, active_rate, INT_MAX);
+	sleep_rate = min_t(u64, sleep_rate, INT_MAX);
+
+	if (active_rate != qp->bus_clk_rate[QCOM_SMD_RPM_ACTIVE_STATE]) {
+		ret = qcom_icc_rpm_set_bus_rate(qp->bus_clk_desc, QCOM_SMD_RPM_ACTIVE_STATE,
+						active_rate);
+		if (ret)
 			return ret;
-		}
-		qp->bus_clk_rate[i] = rate;
+
+		/* Cache the rate after we've successfully commited it to RPM */
+		qp->bus_clk_rate[QCOM_SMD_RPM_ACTIVE_STATE] = active_rate;
+	}
+
+	if (sleep_rate != qp->bus_clk_rate[QCOM_SMD_RPM_SLEEP_STATE]) {
+		ret = qcom_icc_rpm_set_bus_rate(qp->bus_clk_desc, QCOM_SMD_RPM_SLEEP_STATE,
+						sleep_rate);
+		if (ret)
+			return ret;
+
+		/* Cache the rate after we've successfully commited it to RPM */
+		qp->bus_clk_rate[QCOM_SMD_RPM_SLEEP_STATE] = sleep_rate;
 	}
 
 	return 0;
 }
 
-static const char * const bus_clocks[] = {
-	"bus", "bus_a",
-};
-
 int qnoc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -448,6 +459,20 @@ int qnoc_probe(struct platform_device *pdev)
 	if (!qp->intf_clks)
 		return -ENOMEM;
 
+	if (desc->bus_clk_desc) {
+		qp->bus_clk_desc = devm_kzalloc(dev, sizeof(*qp->bus_clk_desc),
+						GFP_KERNEL);
+		if (!qp->bus_clk_desc)
+			return -ENOMEM;
+
+		qp->bus_clk_desc = desc->bus_clk_desc;
+	} else {
+		/* Some older SoCs may have a single non-RPM-owned bus clock. */
+		qp->bus_clk = devm_clk_get_optional(dev, "bus");
+		if (IS_ERR(qp->bus_clk))
+			return PTR_ERR(qp->bus_clk);
+	}
+
 	data = devm_kzalloc(dev, struct_size(data, nodes, num_nodes),
 			    GFP_KERNEL);
 	if (!data)
@@ -457,10 +482,6 @@ int qnoc_probe(struct platform_device *pdev)
 	for (i = 0; i < cd_num; i++)
 		qp->intf_clks[i].id = cds[i];
 
-	qp->num_bus_clks = desc->no_clk_scaling ? 0 : NUM_BUS_CLKS;
-	for (i = 0; i < qp->num_bus_clks; i++)
-		qp->bus_clks[i].id = bus_clocks[i];
-
 	qp->keep_alive = desc->keep_alive;
 	qp->type = desc->type;
 	qp->qos_offset = desc->qos_offset;
@@ -490,11 +511,7 @@ int qnoc_probe(struct platform_device *pdev)
 	}
 
 regmap_done:
-	ret = devm_clk_bulk_get(dev, qp->num_bus_clks, qp->bus_clks);
-	if (ret)
-		return ret;
-
-	ret = clk_bulk_prepare_enable(qp->num_bus_clks, qp->bus_clks);
+	ret = clk_prepare_enable(qp->bus_clk);
 	if (ret)
 		return ret;
 
@@ -566,7 +583,7 @@ int qnoc_probe(struct platform_device *pdev)
 	icc_provider_deregister(provider);
 err_remove_nodes:
 	icc_nodes_remove(provider);
-	clk_bulk_disable_unprepare(qp->num_bus_clks, qp->bus_clks);
+	clk_disable_unprepare(qp->bus_clk);
 
 	return ret;
 }
@@ -578,7 +595,7 @@ int qnoc_remove(struct platform_device *pdev)
 
 	icc_provider_deregister(&qp->provider);
 	icc_nodes_remove(&qp->provider);
-	clk_bulk_disable_unprepare(qp->num_bus_clks, qp->bus_clks);
+	clk_disable_unprepare(qp->bus_clk);
 
 	return 0;
 }
diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index 692d91c248d9..d5da24495d14 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -36,32 +36,29 @@ struct rpm_clk_resource {
 	bool branch;
 };
 
-#define NUM_BUS_CLKS	2
-
 /**
  * struct qcom_icc_provider - Qualcomm specific interconnect provider
  * @provider: generic interconnect provider
- * @num_bus_clks: the total number of bus_clks clk_bulk_data entries (0 or 2)
  * @num_intf_clks: the total number of intf_clks clk_bulk_data entries
  * @type: the ICC provider type
  * @regmap: regmap for QoS registers read/write access
  * @qos_offset: offset to QoS registers
  * @bus_clk_rate: bus clock rate in Hz
- * @bus_clks: the clk_bulk_data table of bus clocks
+ * @bus_clk_desc: a pointer to a rpm_clk_resource description of bus clocks
+ * @bus_clk: a pointer to a HLOS-owned bus clock
  * @intf_clks: a clk_bulk_data array of interface clocks
  * @keep_alive: whether to always keep a minimum vote on the bus clocks
  * @is_on: whether the bus is powered on
  */
 struct qcom_icc_provider {
 	struct icc_provider provider;
-	int num_bus_clks;
 	int num_intf_clks;
 	enum qcom_icc_type type;
 	struct regmap *regmap;
 	unsigned int qos_offset;
-	u64 bus_clk_rate[NUM_BUS_CLKS];
-	struct clk_bulk_data bus_clks[NUM_BUS_CLKS];
+	u32 bus_clk_rate[QCOM_SMD_RPM_STATE_NUM];
 	const struct rpm_clk_resource *bus_clk_desc;
+	struct clk *bus_clk;
 	struct clk_bulk_data *intf_clks;
 	bool keep_alive;
 	bool is_on;
@@ -118,12 +115,10 @@ struct qcom_icc_node {
 struct qcom_icc_desc {
 	struct qcom_icc_node * const *nodes;
 	size_t num_nodes;
-	const char * const *bus_clocks;
 	const struct rpm_clk_resource *bus_clk_desc;
 	const char * const *intf_clocks;
 	size_t num_intf_clocks;
 	bool keep_alive;
-	bool no_clk_scaling;
 	enum qcom_icc_type type;
 	const struct regmap_config *regmap_cfg;
 	unsigned int qos_offset;
diff --git a/drivers/interconnect/qcom/msm8996.c b/drivers/interconnect/qcom/msm8996.c
index a596f4035d2e..8081b3cb1025 100644
--- a/drivers/interconnect/qcom/msm8996.c
+++ b/drivers/interconnect/qcom/msm8996.c
@@ -1818,7 +1818,6 @@ static const struct qcom_icc_desc msm8996_a0noc = {
 	.num_nodes = ARRAY_SIZE(a0noc_nodes),
 	.intf_clocks = a0noc_intf_clocks,
 	.num_intf_clocks = ARRAY_SIZE(a0noc_intf_clocks),
-	.no_clk_scaling = true,
 	.regmap_cfg = &msm8996_a0noc_regmap_config
 };
 
diff --git a/drivers/interconnect/qcom/sdm660.c b/drivers/interconnect/qcom/sdm660.c
index 5743ed680e8e..211fa1fa569c 100644
--- a/drivers/interconnect/qcom/sdm660.c
+++ b/drivers/interconnect/qcom/sdm660.c
@@ -1618,7 +1618,6 @@ static const struct qcom_icc_desc sdm660_gnoc = {
 	.nodes = sdm660_gnoc_nodes,
 	.num_nodes = ARRAY_SIZE(sdm660_gnoc_nodes),
 	.regmap_cfg = &sdm660_gnoc_regmap_config,
-	.no_clk_scaling = true,
 };
 
 static struct qcom_icc_node * const sdm660_mnoc_nodes[] = {

-- 
2.41.0

Re: [PATCH v5 17/22] interconnect: qcom: icc-rpm: Control bus rpmcc from icc

[Stephan Gerhold]

On Wed, Jun 14, 2023 at 12:22:28PM +0200, Konrad Dybcio wrote:
> The sole purpose of bus clocks that were previously registered with
> rpmcc was to convey the aggregated bandwidth to RPM. There's no good
> reason to keep them outside the interconnect framework, as it only
> adds to the plentiful complexity.
> 
> Add the required code to handle these clocks from within SMD RPM ICC.
> 
> RPM-owned bus clocks are no longer considered a thing, but sadly we
> have to allow for the existence of HLOS-owned bus clocks, as some
> (mostly older) SoCs (ab)use these for bus scaling (e.g. MSM8998 and
> &mmcc AHB_CLK_SRC).
> 
> This in turn is trivially solved with a single *clk, which is filled
> and used iff qp.bus_clk_desc is absent and we have a "bus" clock-names
> entry in the DT node.
> 
> This change should(tm) be fully compatible with all sorts of old
> Device Trees as far as the interconnect functionality goes (modulo
> abusing bus clock handles or wrongly using the qcom,icc.h binding,
> but that's a mistake in and of itself).
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Reviewed-by: Stephan Gerhold <stephan@gerhold.net>

Thanks!

> ---
>  drivers/interconnect/qcom/icc-rpm.c | 121 ++++++++++++++++++++----------------
>  drivers/interconnect/qcom/icc-rpm.h |  13 ++--
>  drivers/interconnect/qcom/msm8996.c |   1 -
>  drivers/interconnect/qcom/sdm660.c  |   1 -
>  4 files changed, 73 insertions(+), 63 deletions(-)
> 
> diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
> index b8ecf9538ab9..858880a97d2a 100644
> --- a/drivers/interconnect/qcom/icc-rpm.c
> +++ b/drivers/interconnect/qcom/icc-rpm.c
> @@ -49,7 +49,7 @@
>  #define NOC_QOS_MODE_FIXED_VAL		0x0
>  #define NOC_QOS_MODE_BYPASS_VAL		0x2
>  
> -#define ICC_BUS_CLK_MIN_RATE		19200000ULL
> +#define ICC_BUS_CLK_MIN_RATE		19200ULL /* kHz */
>  
>  static int qcom_icc_set_qnoc_qos(struct icc_node *src)
>  {
> @@ -338,11 +338,10 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
>  	struct qcom_icc_node *src_qn = NULL, *dst_qn = NULL;
>  	struct icc_provider *provider;
>  	u64 sum_bw;
> -	u64 rate;
> +	u64 active_rate, sleep_rate;
>  	u64 agg_avg[QCOM_ICC_NUM_BUCKETS], agg_peak[QCOM_ICC_NUM_BUCKETS];
>  	u64 max_agg_avg;
> -	int ret, i;
> -	int bucket;
> +	int ret;
>  
>  	src_qn = src->data;
>  	if (dst)
> @@ -364,49 +363,61 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
>  			return ret;
>  	}
>  
> -	for (i = 0; i < qp->num_bus_clks; i++) {
> -		/*
> -		 * Use WAKE bucket for active clock, otherwise, use SLEEP bucket
> -		 * for other clocks.  If a platform doesn't set interconnect
> -		 * path tags, by default use sleep bucket for all clocks.
> -		 *
> -		 * Note, AMC bucket is not supported yet.
> -		 */
> -		if (!strcmp(qp->bus_clks[i].id, "bus_a"))
> -			bucket = QCOM_ICC_BUCKET_WAKE;
> -		else
> -			bucket = QCOM_ICC_BUCKET_SLEEP;
> -
> -		rate = icc_units_to_bps(max(agg_avg[bucket], agg_peak[bucket]));
> -		do_div(rate, src_qn->buswidth);
> -		rate = min_t(u64, rate, LONG_MAX);
> -
> -		/*
> -		 * Downstream checks whether the requested rate is zero, but it makes little sense
> -		 * to vote for a value that's below the lower threshold, so let's not do so.
> -		 */
> -		if (bucket == QCOM_ICC_BUCKET_WAKE && qp->keep_alive)
> -			rate = max(ICC_BUS_CLK_MIN_RATE, rate);
> -
> -		if (qp->bus_clk_rate[i] == rate)
> -			continue;
> -
> -		ret = clk_set_rate(qp->bus_clks[i].clk, rate);
> -		if (ret) {
> -			pr_err("%s clk_set_rate error: %d\n",
> -			       qp->bus_clks[i].id, ret);
> +	/* Some providers don't have a bus clock to scale */
> +	if (!qp->bus_clk_desc && !qp->bus_clk)
> +		return 0;
> +
> +	/* Intentionally keep the rates in kHz as that's what RPM accepts */
> +	active_rate = max(agg_avg[QCOM_SMD_RPM_ACTIVE_STATE],
> +			  agg_peak[QCOM_SMD_RPM_ACTIVE_STATE]);
> +	do_div(active_rate, src_qn->buswidth);
> +
> +	sleep_rate = max(agg_avg[QCOM_SMD_RPM_SLEEP_STATE],
> +			 agg_peak[QCOM_SMD_RPM_SLEEP_STATE]);
> +	do_div(sleep_rate, src_qn->buswidth);
> +
> +	/*
> +	 * Downstream checks whether the requested rate is zero, but it makes little sense
> +	 * to vote for a value that's below the lower threshold, so let's not do so.
> +	 */
> +	if (qp->keep_alive)
> +		active_rate = max(ICC_BUS_CLK_MIN_RATE, active_rate);
> +
> +	/* Some providers have a non-RPM-owned bus clock - convert kHz->Hz for the CCF */
> +	if (qp->bus_clk) {
> +		active_rate = max_t(u64, active_rate, sleep_rate);
> +		/* ARM32 caps clk_set_rate arg to u32.. Nothing we can do about that! */
> +		active_rate = min_t(u64, 1000ULL * active_rate, ULONG_MAX);
> +		return clk_set_rate(qp->bus_clk, active_rate);
> +	}
> +
> +	/* RPM only accepts <=INT_MAX rates */
> +	active_rate = min_t(u64, active_rate, INT_MAX);
> +	sleep_rate = min_t(u64, sleep_rate, INT_MAX);
> +
> +	if (active_rate != qp->bus_clk_rate[QCOM_SMD_RPM_ACTIVE_STATE]) {
> +		ret = qcom_icc_rpm_set_bus_rate(qp->bus_clk_desc, QCOM_SMD_RPM_ACTIVE_STATE,
> +						active_rate);
> +		if (ret)
>  			return ret;
> -		}
> -		qp->bus_clk_rate[i] = rate;
> +
> +		/* Cache the rate after we've successfully commited it to RPM */
> +		qp->bus_clk_rate[QCOM_SMD_RPM_ACTIVE_STATE] = active_rate;
> +	}
> +
> +	if (sleep_rate != qp->bus_clk_rate[QCOM_SMD_RPM_SLEEP_STATE]) {
> +		ret = qcom_icc_rpm_set_bus_rate(qp->bus_clk_desc, QCOM_SMD_RPM_SLEEP_STATE,
> +						sleep_rate);
> +		if (ret)
> +			return ret;
> +
> +		/* Cache the rate after we've successfully commited it to RPM */
> +		qp->bus_clk_rate[QCOM_SMD_RPM_SLEEP_STATE] = sleep_rate;
>  	}
>  
>  	return 0;
>  }
>  
> -static const char * const bus_clocks[] = {
> -	"bus", "bus_a",
> -};
> -
>  int qnoc_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
> @@ -448,6 +459,20 @@ int qnoc_probe(struct platform_device *pdev)
>  	if (!qp->intf_clks)
>  		return -ENOMEM;
>  
> +	if (desc->bus_clk_desc) {
> +		qp->bus_clk_desc = devm_kzalloc(dev, sizeof(*qp->bus_clk_desc),
> +						GFP_KERNEL);
> +		if (!qp->bus_clk_desc)
> +			return -ENOMEM;
> +
> +		qp->bus_clk_desc = desc->bus_clk_desc;
> +	} else {
> +		/* Some older SoCs may have a single non-RPM-owned bus clock. */
> +		qp->bus_clk = devm_clk_get_optional(dev, "bus");
> +		if (IS_ERR(qp->bus_clk))
> +			return PTR_ERR(qp->bus_clk);
> +	}
> +
>  	data = devm_kzalloc(dev, struct_size(data, nodes, num_nodes),
>  			    GFP_KERNEL);
>  	if (!data)
> @@ -457,10 +482,6 @@ int qnoc_probe(struct platform_device *pdev)
>  	for (i = 0; i < cd_num; i++)
>  		qp->intf_clks[i].id = cds[i];
>  
> -	qp->num_bus_clks = desc->no_clk_scaling ? 0 : NUM_BUS_CLKS;
> -	for (i = 0; i < qp->num_bus_clks; i++)
> -		qp->bus_clks[i].id = bus_clocks[i];
> -
>  	qp->keep_alive = desc->keep_alive;
>  	qp->type = desc->type;
>  	qp->qos_offset = desc->qos_offset;
> @@ -490,11 +511,7 @@ int qnoc_probe(struct platform_device *pdev)
>  	}
>  
>  regmap_done:
> -	ret = devm_clk_bulk_get(dev, qp->num_bus_clks, qp->bus_clks);
> -	if (ret)
> -		return ret;
> -
> -	ret = clk_bulk_prepare_enable(qp->num_bus_clks, qp->bus_clks);
> +	ret = clk_prepare_enable(qp->bus_clk);
>  	if (ret)
>  		return ret;
>  
> @@ -566,7 +583,7 @@ int qnoc_probe(struct platform_device *pdev)
>  	icc_provider_deregister(provider);
>  err_remove_nodes:
>  	icc_nodes_remove(provider);
> -	clk_bulk_disable_unprepare(qp->num_bus_clks, qp->bus_clks);
> +	clk_disable_unprepare(qp->bus_clk);
>  
>  	return ret;
>  }
> @@ -578,7 +595,7 @@ int qnoc_remove(struct platform_device *pdev)
>  
>  	icc_provider_deregister(&qp->provider);
>  	icc_nodes_remove(&qp->provider);
> -	clk_bulk_disable_unprepare(qp->num_bus_clks, qp->bus_clks);
> +	clk_disable_unprepare(qp->bus_clk);
>  
>  	return 0;
>  }
> diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
> index 692d91c248d9..d5da24495d14 100644
> --- a/drivers/interconnect/qcom/icc-rpm.h
> +++ b/drivers/interconnect/qcom/icc-rpm.h
> @@ -36,32 +36,29 @@ struct rpm_clk_resource {
>  	bool branch;
>  };
>  
> -#define NUM_BUS_CLKS	2
> -
>  /**
>   * struct qcom_icc_provider - Qualcomm specific interconnect provider
>   * @provider: generic interconnect provider
> - * @num_bus_clks: the total number of bus_clks clk_bulk_data entries (0 or 2)
>   * @num_intf_clks: the total number of intf_clks clk_bulk_data entries
>   * @type: the ICC provider type
>   * @regmap: regmap for QoS registers read/write access
>   * @qos_offset: offset to QoS registers
>   * @bus_clk_rate: bus clock rate in Hz
> - * @bus_clks: the clk_bulk_data table of bus clocks
> + * @bus_clk_desc: a pointer to a rpm_clk_resource description of bus clocks
> + * @bus_clk: a pointer to a HLOS-owned bus clock
>   * @intf_clks: a clk_bulk_data array of interface clocks
>   * @keep_alive: whether to always keep a minimum vote on the bus clocks
>   * @is_on: whether the bus is powered on
>   */
>  struct qcom_icc_provider {
>  	struct icc_provider provider;
> -	int num_bus_clks;
>  	int num_intf_clks;
>  	enum qcom_icc_type type;
>  	struct regmap *regmap;
>  	unsigned int qos_offset;
> -	u64 bus_clk_rate[NUM_BUS_CLKS];
> -	struct clk_bulk_data bus_clks[NUM_BUS_CLKS];
> +	u32 bus_clk_rate[QCOM_SMD_RPM_STATE_NUM];
>  	const struct rpm_clk_resource *bus_clk_desc;
> +	struct clk *bus_clk;
>  	struct clk_bulk_data *intf_clks;
>  	bool keep_alive;
>  	bool is_on;
> @@ -118,12 +115,10 @@ struct qcom_icc_node {
>  struct qcom_icc_desc {
>  	struct qcom_icc_node * const *nodes;
>  	size_t num_nodes;
> -	const char * const *bus_clocks;
>  	const struct rpm_clk_resource *bus_clk_desc;
>  	const char * const *intf_clocks;
>  	size_t num_intf_clocks;
>  	bool keep_alive;
> -	bool no_clk_scaling;
>  	enum qcom_icc_type type;
>  	const struct regmap_config *regmap_cfg;
>  	unsigned int qos_offset;
> diff --git a/drivers/interconnect/qcom/msm8996.c b/drivers/interconnect/qcom/msm8996.c
> index a596f4035d2e..8081b3cb1025 100644
> --- a/drivers/interconnect/qcom/msm8996.c
> +++ b/drivers/interconnect/qcom/msm8996.c
> @@ -1818,7 +1818,6 @@ static const struct qcom_icc_desc msm8996_a0noc = {
>  	.num_nodes = ARRAY_SIZE(a0noc_nodes),
>  	.intf_clocks = a0noc_intf_clocks,
>  	.num_intf_clocks = ARRAY_SIZE(a0noc_intf_clocks),
> -	.no_clk_scaling = true,
>  	.regmap_cfg = &msm8996_a0noc_regmap_config
>  };
>  
> diff --git a/drivers/interconnect/qcom/sdm660.c b/drivers/interconnect/qcom/sdm660.c
> index 5743ed680e8e..211fa1fa569c 100644
> --- a/drivers/interconnect/qcom/sdm660.c
> +++ b/drivers/interconnect/qcom/sdm660.c
> @@ -1618,7 +1618,6 @@ static const struct qcom_icc_desc sdm660_gnoc = {
>  	.nodes = sdm660_gnoc_nodes,
>  	.num_nodes = ARRAY_SIZE(sdm660_gnoc_nodes),
>  	.regmap_cfg = &sdm660_gnoc_regmap_config,
> -	.no_clk_scaling = true,
>  };
>  
>  static struct qcom_icc_node * const sdm660_mnoc_nodes[] = {
> 
> -- 
> 2.41.0
> 

[PATCH v5 18/22] clk: qcom: smd-rpm: Separate out interconnect bus clocks

[Konrad Dybcio]

The interconnect bus clocks are now handled within the ICC framework.
They still however need to get a kickstart *before* we call
clk_smd_rpm_enable_scaling(), or RPM will assume that they should all
be running at 0 kHz and the system will inevitably die.

Separate them out to ensure such a kickstart can still take place.

As a happy accident, the file got smaller:

Total: Before=41951, After=41555, chg -0.94%

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/clk/qcom/clk-smd-rpm.c | 278 +++++++++++++++++------------------------
 1 file changed, 115 insertions(+), 163 deletions(-)

diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c
index 6e7f0438e8b8..0d1d97659d59 100644
--- a/drivers/clk/qcom/clk-smd-rpm.c
+++ b/drivers/clk/qcom/clk-smd-rpm.c
@@ -167,6 +167,14 @@ struct clk_smd_rpm {
 struct rpm_smd_clk_desc {
 	struct clk_smd_rpm **clks;
 	size_t num_clks;
+
+	/*
+	 * Interconnect clocks are managed by the icc framework, this driver
+	 * only kickstarts them so that they don't get gated between
+	 * clk_smd_rpm_enable_scaling() and interconnect driver initialization.
+	 */
+	struct clk_smd_rpm **icc_clks;
+	size_t num_icc_clks;
 	bool scaling_before_handover;
 };
 
@@ -498,13 +506,69 @@ DEFINE_CLK_SMD_RPM_XO_BUFFER(div_clk1, 11, 19200000);
 DEFINE_CLK_SMD_RPM_XO_BUFFER(div_clk2, 12, 19200000);
 DEFINE_CLK_SMD_RPM_XO_BUFFER(div_clk3, 13, 19200000);
 
+static struct clk_smd_rpm *bimc_pcnoc_icc_clks[] = {
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_0_pcnoc_clk,
+};
+
+static struct clk_smd_rpm *bimc_pcnoc_snoc_icc_clks[] = {
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_0_pcnoc_clk,
+	&clk_smd_rpm_bus_1_snoc_clk,
+};
+
+static struct clk_smd_rpm *bimc_pcnoc_snoc_smmnoc_icc_clks[] = {
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_0_pcnoc_clk,
+	&clk_smd_rpm_bus_1_snoc_clk,
+	&clk_smd_rpm_bus_2_sysmmnoc_clk,
+};
+
+static struct clk_smd_rpm *bimc_pcnoc_snoc_cnoc_ocmem_icc_clks[] = {
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_0_pcnoc_clk,
+	&clk_smd_rpm_bus_1_snoc_clk,
+	&clk_smd_rpm_bus_2_cnoc_clk,
+	&clk_smd_rpm_ocmemgx_clk,
+};
+
+static struct clk_smd_rpm *msm8996_icc_clks[] = {
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_branch_aggre1_noc_clk,
+	&clk_smd_rpm_branch_aggre2_noc_clk,
+	&clk_smd_rpm_bus_0_pcnoc_clk,
+	&clk_smd_rpm_bus_1_snoc_clk,
+	&clk_smd_rpm_bus_2_cnoc_clk,
+	&clk_smd_rpm_mmssnoc_axi_rpm_clk,
+};
+
+static struct clk_smd_rpm *msm8998_icc_clks[] = {
+	&clk_smd_rpm_aggre1_noc_clk,
+	&clk_smd_rpm_aggre2_noc_clk,
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_1_snoc_clk,
+	&clk_smd_rpm_bus_2_cnoc_clk,
+	&clk_smd_rpm_mmssnoc_axi_rpm_clk,
+};
+
+static struct clk_smd_rpm *sdm660_icc_clks[] = {
+	&clk_smd_rpm_aggre2_noc_clk,
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_1_snoc_clk,
+	&clk_smd_rpm_bus_2_cnoc_clk,
+	&clk_smd_rpm_mmssnoc_axi_rpm_clk,
+};
+
+static struct clk_smd_rpm *sm_qnoc_icc_clks[] = {
+	&clk_smd_rpm_bimc_clk,
+	&clk_smd_rpm_bus_1_cnoc_clk,
+	&clk_smd_rpm_mmnrt_clk,
+	&clk_smd_rpm_mmrt_clk,
+	&clk_smd_rpm_qup_clk,
+	&clk_smd_rpm_bus_2_snoc_clk,
+};
+
 static struct clk_smd_rpm *msm8909_clks[] = {
-	[RPM_SMD_PCNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK]		= &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK]		= &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QPIC_CLK]		= &clk_smd_rpm_qpic_clk,
 	[RPM_SMD_QPIC_CLK_A]		= &clk_smd_rpm_qpic_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
@@ -530,15 +594,11 @@ static struct clk_smd_rpm *msm8909_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8909 = {
 	.clks = msm8909_clks,
 	.num_clks = ARRAY_SIZE(msm8909_clks),
+	.icc_clks = bimc_pcnoc_snoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8916_clks[] = {
-	[RPM_SMD_PCNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK]		= &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK]		= &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK]		= &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_BB_CLK1]		= &clk_smd_rpm_bb_clk1,
@@ -562,21 +622,15 @@ static struct clk_smd_rpm *msm8916_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8916 = {
 	.clks = msm8916_clks,
 	.num_clks = ARRAY_SIZE(msm8916_clks),
+	.icc_clks = bimc_pcnoc_snoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8917_clks[] = {
 	[RPM_SMD_XO_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK]		= &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK]		= &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_BIMC_GPU_CLK]		= &clk_smd_rpm_bimc_gpu_clk,
 	[RPM_SMD_BIMC_GPU_A_CLK]	= &clk_smd_rpm_bimc_gpu_a_clk,
-	[RPM_SMD_SYSMMNOC_CLK]		= &clk_smd_rpm_bus_2_sysmmnoc_clk,
-	[RPM_SMD_SYSMMNOC_A_CLK]	= &clk_smd_rpm_bus_2_sysmmnoc_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK]		= &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_BB_CLK1]		= &clk_smd_rpm_bb_clk1,
@@ -596,19 +650,13 @@ static struct clk_smd_rpm *msm8917_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8917 = {
 	.clks = msm8917_clks,
 	.num_clks = ARRAY_SIZE(msm8917_clks),
+	.icc_clks = bimc_pcnoc_snoc_smmnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_smmnoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8936_clks[] = {
 	[RPM_SMD_XO_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PCNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK]		= &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK]		= &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_SYSMMNOC_CLK]		= &clk_smd_rpm_bus_2_sysmmnoc_clk,
-	[RPM_SMD_SYSMMNOC_A_CLK]	= &clk_smd_rpm_bus_2_sysmmnoc_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK]		= &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_BB_CLK1]		= &clk_smd_rpm_bb_clk1,
@@ -632,25 +680,17 @@ static struct clk_smd_rpm *msm8936_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8936 = {
 		.clks = msm8936_clks,
 		.num_clks = ARRAY_SIZE(msm8936_clks),
+		.icc_clks = bimc_pcnoc_snoc_smmnoc_icc_clks,
+		.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_smmnoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8974_clks[] = {
 	[RPM_SMD_XO_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK]		= &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK]		= &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_CNOC_CLK]		= &clk_smd_rpm_bus_2_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK]		= &clk_smd_rpm_bus_2_cnoc_a_clk,
 	[RPM_SMD_MMSSNOC_AHB_CLK]	= &clk_smd_rpm_bus_3_mmssnoc_ahb_clk,
 	[RPM_SMD_MMSSNOC_AHB_A_CLK]	= &clk_smd_rpm_bus_3_mmssnoc_ahb_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
 	[RPM_SMD_GFX3D_CLK_SRC]		= &clk_smd_rpm_gfx3d_clk_src,
 	[RPM_SMD_GFX3D_A_CLK_SRC]	= &clk_smd_rpm_gfx3d_a_clk_src,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_OCMEMGX_CLK]		= &clk_smd_rpm_ocmemgx_clk,
-	[RPM_SMD_OCMEMGX_A_CLK]		= &clk_smd_rpm_ocmemgx_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK]		= &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_CXO_D0]		= &clk_smd_rpm_cxo_d0,
@@ -684,20 +724,14 @@ static struct clk_smd_rpm *msm8974_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8974 = {
 	.clks = msm8974_clks,
 	.num_clks = ARRAY_SIZE(msm8974_clks),
+	.icc_clks = bimc_pcnoc_snoc_cnoc_ocmem_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_cnoc_ocmem_icc_clks),
 	.scaling_before_handover = true,
 };
 
 static struct clk_smd_rpm *msm8976_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PCNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_SYSMMNOC_CLK]	= &clk_smd_rpm_bus_2_sysmmnoc_clk,
-	[RPM_SMD_SYSMMNOC_A_CLK] = &clk_smd_rpm_bus_2_sysmmnoc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_BB_CLK1] = &clk_smd_rpm_bb_clk1,
@@ -718,24 +752,15 @@ static struct clk_smd_rpm *msm8976_clks[] = {
 
 static const struct rpm_smd_clk_desc rpm_clk_msm8976 = {
 	.clks = msm8976_clks,
-	.num_clks = ARRAY_SIZE(msm8976_clks),
+	.icc_clks = bimc_pcnoc_snoc_smmnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_smmnoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8992_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_OCMEMGX_CLK] = &clk_smd_rpm_ocmemgx_clk,
-	[RPM_SMD_OCMEMGX_A_CLK] = &clk_smd_rpm_ocmemgx_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_2_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_2_cnoc_a_clk,
 	[RPM_SMD_GFX3D_CLK_SRC] = &clk_smd_rpm_gfx3d_clk_src,
 	[RPM_SMD_GFX3D_A_CLK_SRC] = &clk_smd_rpm_gfx3d_a_clk_src,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_1_snoc_a_clk,
 	[RPM_SMD_BB_CLK1] = &clk_smd_rpm_bb_clk1,
 	[RPM_SMD_BB_CLK1_A] = &clk_smd_rpm_bb_clk1_a,
 	[RPM_SMD_BB_CLK1_PIN] = &clk_smd_rpm_bb_clk1_pin,
@@ -777,23 +802,15 @@ static struct clk_smd_rpm *msm8992_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8992 = {
 	.clks = msm8992_clks,
 	.num_clks = ARRAY_SIZE(msm8992_clks),
+	.icc_clks = bimc_pcnoc_snoc_cnoc_ocmem_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_cnoc_ocmem_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8994_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_OCMEMGX_CLK] = &clk_smd_rpm_ocmemgx_clk,
-	[RPM_SMD_OCMEMGX_A_CLK] = &clk_smd_rpm_ocmemgx_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_2_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_2_cnoc_a_clk,
 	[RPM_SMD_GFX3D_CLK_SRC] = &clk_smd_rpm_gfx3d_clk_src,
 	[RPM_SMD_GFX3D_A_CLK_SRC] = &clk_smd_rpm_gfx3d_a_clk_src,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_1_snoc_a_clk,
 	[RPM_SMD_BB_CLK1] = &clk_smd_rpm_bb_clk1,
 	[RPM_SMD_BB_CLK1_A] = &clk_smd_rpm_bb_clk1_a,
 	[RPM_SMD_BB_CLK1_PIN] = &clk_smd_rpm_bb_clk1_pin,
@@ -837,29 +854,17 @@ static struct clk_smd_rpm *msm8994_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8994 = {
 	.clks = msm8994_clks,
 	.num_clks = ARRAY_SIZE(msm8994_clks),
+	.icc_clks = bimc_pcnoc_snoc_cnoc_ocmem_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_cnoc_ocmem_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8996_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PCNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_2_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_2_cnoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_MMAXI_CLK] = &clk_smd_rpm_mmssnoc_axi_rpm_clk,
-	[RPM_SMD_MMAXI_A_CLK] = &clk_smd_rpm_mmssnoc_axi_rpm_a_clk,
 	[RPM_SMD_IPA_CLK] = &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK] = &clk_smd_rpm_ipa_a_clk,
 	[RPM_SMD_CE1_CLK] = &clk_smd_rpm_ce1_clk,
 	[RPM_SMD_CE1_A_CLK] = &clk_smd_rpm_ce1_a_clk,
-	[RPM_SMD_AGGR1_NOC_CLK] = &clk_smd_rpm_branch_aggre1_noc_clk,
-	[RPM_SMD_AGGR1_NOC_A_CLK] = &clk_smd_rpm_branch_aggre1_noc_a_clk,
-	[RPM_SMD_AGGR2_NOC_CLK] = &clk_smd_rpm_branch_aggre2_noc_clk,
-	[RPM_SMD_AGGR2_NOC_A_CLK] = &clk_smd_rpm_branch_aggre2_noc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_BB_CLK1] = &clk_smd_rpm_bb_clk1,
@@ -891,6 +896,8 @@ static struct clk_smd_rpm *msm8996_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8996 = {
 	.clks = msm8996_clks,
 	.num_clks = ARRAY_SIZE(msm8996_clks),
+	.icc_clks = msm8996_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(msm8996_icc_clks),
 };
 
 static struct clk_smd_rpm *qcs404_clks[] = {
@@ -919,19 +926,15 @@ static struct clk_smd_rpm *qcs404_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_qcs404 = {
 	.clks = qcs404_clks,
 	.num_clks = ARRAY_SIZE(qcs404_clks),
+	.icc_clks = bimc_pcnoc_snoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8998_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_PCNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
 	[RPM_SMD_PCNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_2_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_2_cnoc_a_clk,
 	[RPM_SMD_CE1_CLK] = &clk_smd_rpm_ce1_clk,
 	[RPM_SMD_CE1_A_CLK] = &clk_smd_rpm_ce1_a_clk,
 	[RPM_SMD_DIV_CLK1] = &clk_smd_rpm_div_clk1,
@@ -954,12 +957,6 @@ static struct clk_smd_rpm *msm8998_clks[] = {
 	[RPM_SMD_LN_BB_CLK2_A_PIN] = &clk_smd_rpm_ln_bb_clk2_a_pin,
 	[RPM_SMD_LN_BB_CLK3_PIN] = &clk_smd_rpm_ln_bb_clk3_pin,
 	[RPM_SMD_LN_BB_CLK3_A_PIN] = &clk_smd_rpm_ln_bb_clk3_a_pin,
-	[RPM_SMD_MMAXI_CLK] = &clk_smd_rpm_mmssnoc_axi_rpm_clk,
-	[RPM_SMD_MMAXI_A_CLK] = &clk_smd_rpm_mmssnoc_axi_rpm_a_clk,
-	[RPM_SMD_AGGR1_NOC_CLK] = &clk_smd_rpm_aggre1_noc_clk,
-	[RPM_SMD_AGGR1_NOC_A_CLK] = &clk_smd_rpm_aggre1_noc_a_clk,
-	[RPM_SMD_AGGR2_NOC_CLK] = &clk_smd_rpm_aggre2_noc_clk,
-	[RPM_SMD_AGGR2_NOC_A_CLK] = &clk_smd_rpm_aggre2_noc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_RF_CLK1] = &clk_smd_rpm_rf_clk1,
@@ -979,27 +976,19 @@ static struct clk_smd_rpm *msm8998_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8998 = {
 	.clks = msm8998_clks,
 	.num_clks = ARRAY_SIZE(msm8998_clks),
+	.icc_clks = msm8998_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(msm8998_icc_clks),
 };
 
 static struct clk_smd_rpm *sdm660_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_2_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_2_cnoc_a_clk,
 	[RPM_SMD_CNOC_PERIPH_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
 	[RPM_SMD_CNOC_PERIPH_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
-	[RPM_SMD_MMSSNOC_AXI_CLK] = &clk_smd_rpm_mmssnoc_axi_rpm_clk,
-	[RPM_SMD_MMSSNOC_AXI_CLK_A] = &clk_smd_rpm_mmssnoc_axi_rpm_a_clk,
 	[RPM_SMD_IPA_CLK] = &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK] = &clk_smd_rpm_ipa_a_clk,
 	[RPM_SMD_CE1_CLK] = &clk_smd_rpm_ce1_clk,
 	[RPM_SMD_CE1_A_CLK] = &clk_smd_rpm_ce1_a_clk,
-	[RPM_SMD_AGGR2_NOC_CLK] = &clk_smd_rpm_aggre2_noc_clk,
-	[RPM_SMD_AGGR2_NOC_A_CLK] = &clk_smd_rpm_aggre2_noc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_RF_CLK1] = &clk_smd_rpm_rf_clk1,
@@ -1025,15 +1014,13 @@ static struct clk_smd_rpm *sdm660_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_sdm660 = {
 	.clks = sdm660_clks,
 	.num_clks = ARRAY_SIZE(sdm660_clks),
+	.icc_clks = sdm660_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(sdm660_icc_clks),
 };
 
 static struct clk_smd_rpm *mdm9607_clks[] = {
 	[RPM_SMD_XO_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PCNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QPIC_CLK]		= &clk_smd_rpm_qpic_clk,
 	[RPM_SMD_QPIC_CLK_A]		= &clk_smd_rpm_qpic_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
@@ -1047,21 +1034,15 @@ static struct clk_smd_rpm *mdm9607_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_mdm9607 = {
 	.clks = mdm9607_clks,
 	.num_clks = ARRAY_SIZE(mdm9607_clks),
+	.icc_clks = bimc_pcnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_icc_clks),
 };
 
 static struct clk_smd_rpm *msm8953_clks[] = {
 	[RPM_SMD_XO_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC]		= &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_PCNOC_CLK]		= &clk_smd_rpm_bus_0_pcnoc_clk,
-	[RPM_SMD_PCNOC_A_CLK]		= &clk_smd_rpm_bus_0_pcnoc_a_clk,
-	[RPM_SMD_SNOC_CLK]		= &clk_smd_rpm_bus_1_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK]		= &clk_smd_rpm_bus_1_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK]		= &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK]		= &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_IPA_CLK]		= &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK]		= &clk_smd_rpm_ipa_a_clk,
-	[RPM_SMD_SYSMMNOC_CLK]		= &clk_smd_rpm_bus_2_sysmmnoc_clk,
-	[RPM_SMD_SYSMMNOC_A_CLK]	= &clk_smd_rpm_bus_2_sysmmnoc_a_clk,
 	[RPM_SMD_QDSS_CLK]		= &clk_smd_rpm_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK]		= &clk_smd_rpm_qdss_a_clk,
 	[RPM_SMD_BB_CLK1]		= &clk_smd_rpm_bb_clk1,
@@ -1083,23 +1064,19 @@ static struct clk_smd_rpm *msm8953_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_msm8953 = {
 	.clks = msm8953_clks,
 	.num_clks = ARRAY_SIZE(msm8953_clks),
+	.icc_clks = bimc_pcnoc_snoc_smmnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(bimc_pcnoc_snoc_smmnoc_icc_clks),
 };
 
 static struct clk_smd_rpm *sm6125_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_2_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_2_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_branch_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_branch_qdss_a_clk,
 	[RPM_SMD_RF_CLK1] = &clk_smd_rpm_rf_clk1,
 	[RPM_SMD_RF_CLK1_A] = &clk_smd_rpm_rf_clk1_a,
 	[RPM_SMD_RF_CLK2] = &clk_smd_rpm_rf_clk2,
 	[RPM_SMD_RF_CLK2_A] = &clk_smd_rpm_rf_clk2_a,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_1_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_1_cnoc_a_clk,
 	[RPM_SMD_IPA_CLK] = &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK] = &clk_smd_rpm_ipa_a_clk,
 	[RPM_SMD_CE1_CLK] = &clk_smd_rpm_ce1_clk,
@@ -1110,12 +1087,6 @@ static struct clk_smd_rpm *sm6125_clks[] = {
 	[RPM_SMD_LN_BB_CLK2_A] = &clk_smd_rpm_ln_bb_clk2_a,
 	[RPM_SMD_LN_BB_CLK3] = &clk_smd_rpm_ln_bb_clk3,
 	[RPM_SMD_LN_BB_CLK3_A] = &clk_smd_rpm_ln_bb_clk3_a,
-	[RPM_SMD_QUP_CLK] = &clk_smd_rpm_qup_clk,
-	[RPM_SMD_QUP_A_CLK] = &clk_smd_rpm_qup_a_clk,
-	[RPM_SMD_MMRT_CLK] = &clk_smd_rpm_mmrt_clk,
-	[RPM_SMD_MMRT_A_CLK] = &clk_smd_rpm_mmrt_a_clk,
-	[RPM_SMD_MMNRT_CLK] = &clk_smd_rpm_mmnrt_clk,
-	[RPM_SMD_MMNRT_A_CLK] = &clk_smd_rpm_mmnrt_a_clk,
 	[RPM_SMD_SNOC_PERIPH_CLK] = &clk_smd_rpm_bus_0_snoc_periph_clk,
 	[RPM_SMD_SNOC_PERIPH_A_CLK] = &clk_smd_rpm_bus_0_snoc_periph_a_clk,
 	[RPM_SMD_SNOC_LPASS_CLK] = &clk_smd_rpm_bus_5_snoc_lpass_clk,
@@ -1125,34 +1096,24 @@ static struct clk_smd_rpm *sm6125_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_sm6125 = {
 	.clks = sm6125_clks,
 	.num_clks = ARRAY_SIZE(sm6125_clks),
+	.icc_clks = sm_qnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(sm_qnoc_icc_clks)
 };
 
 /* SM6115 */
 static struct clk_smd_rpm *sm6115_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_2_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_2_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_branch_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_branch_qdss_a_clk,
 	[RPM_SMD_RF_CLK1] = &clk_smd_rpm_rf_clk1,
 	[RPM_SMD_RF_CLK1_A] = &clk_smd_rpm_rf_clk1_a,
 	[RPM_SMD_RF_CLK2] = &clk_smd_rpm_rf_clk2,
 	[RPM_SMD_RF_CLK2_A] = &clk_smd_rpm_rf_clk2_a,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_1_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_1_cnoc_a_clk,
 	[RPM_SMD_IPA_CLK] = &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK] = &clk_smd_rpm_ipa_a_clk,
 	[RPM_SMD_CE1_CLK] = &clk_smd_rpm_ce1_clk,
 	[RPM_SMD_CE1_A_CLK] = &clk_smd_rpm_ce1_a_clk,
-	[RPM_SMD_QUP_CLK] = &clk_smd_rpm_qup_clk,
-	[RPM_SMD_QUP_A_CLK] = &clk_smd_rpm_qup_a_clk,
-	[RPM_SMD_MMRT_CLK] = &clk_smd_rpm_mmrt_clk,
-	[RPM_SMD_MMRT_A_CLK] = &clk_smd_rpm_mmrt_a_clk,
-	[RPM_SMD_MMNRT_CLK] = &clk_smd_rpm_mmnrt_clk,
-	[RPM_SMD_MMNRT_A_CLK] = &clk_smd_rpm_mmnrt_a_clk,
 	[RPM_SMD_SNOC_PERIPH_CLK] = &clk_smd_rpm_bus_0_snoc_periph_clk,
 	[RPM_SMD_SNOC_PERIPH_A_CLK] = &clk_smd_rpm_bus_0_snoc_periph_a_clk,
 	[RPM_SMD_SNOC_LPASS_CLK] = &clk_smd_rpm_bus_5_snoc_lpass_clk,
@@ -1166,27 +1127,17 @@ static struct clk_smd_rpm *sm6115_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_sm6115 = {
 	.clks = sm6115_clks,
 	.num_clks = ARRAY_SIZE(sm6115_clks),
+	.icc_clks = sm_qnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(sm_qnoc_icc_clks)
 };
 
 static struct clk_smd_rpm *sm6375_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_2_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_2_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_branch_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_branch_qdss_a_clk,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_1_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_1_cnoc_a_clk,
 	[RPM_SMD_IPA_CLK] = &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK] = &clk_smd_rpm_ipa_a_clk,
-	[RPM_SMD_QUP_CLK] = &clk_smd_rpm_qup_clk,
-	[RPM_SMD_QUP_A_CLK] = &clk_smd_rpm_qup_a_clk,
-	[RPM_SMD_MMRT_CLK] = &clk_smd_rpm_mmrt_clk,
-	[RPM_SMD_MMRT_A_CLK] = &clk_smd_rpm_mmrt_a_clk,
-	[RPM_SMD_MMNRT_CLK] = &clk_smd_rpm_mmnrt_clk,
-	[RPM_SMD_MMNRT_A_CLK] = &clk_smd_rpm_mmnrt_a_clk,
 	[RPM_SMD_SNOC_PERIPH_CLK] = &clk_smd_rpm_bus_0_snoc_periph_clk,
 	[RPM_SMD_SNOC_PERIPH_A_CLK] = &clk_smd_rpm_bus_0_snoc_periph_a_clk,
 	[RPM_SMD_SNOC_LPASS_CLK] = &clk_smd_rpm_bus_5_snoc_lpass_clk,
@@ -1203,31 +1154,21 @@ static struct clk_smd_rpm *sm6375_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_sm6375 = {
 	.clks = sm6375_clks,
 	.num_clks = ARRAY_SIZE(sm6375_clks),
+	.icc_clks = sm_qnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(sm_qnoc_icc_clks)
 };
 
 static struct clk_smd_rpm *qcm2290_clks[] = {
 	[RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
 	[RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
-	[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_2_snoc_clk,
-	[RPM_SMD_SNOC_A_CLK] = &clk_smd_rpm_bus_2_snoc_a_clk,
-	[RPM_SMD_BIMC_CLK] = &clk_smd_rpm_bimc_clk,
-	[RPM_SMD_BIMC_A_CLK] = &clk_smd_rpm_bimc_a_clk,
 	[RPM_SMD_QDSS_CLK] = &clk_smd_rpm_branch_qdss_clk,
 	[RPM_SMD_QDSS_A_CLK] = &clk_smd_rpm_branch_qdss_a_clk,
 	[RPM_SMD_LN_BB_CLK2] = &clk_smd_rpm_ln_bb_clk2,
 	[RPM_SMD_LN_BB_CLK2_A] = &clk_smd_rpm_ln_bb_clk2_a,
 	[RPM_SMD_RF_CLK3] = &clk_smd_rpm_38m4_rf_clk3,
 	[RPM_SMD_RF_CLK3_A] = &clk_smd_rpm_38m4_rf_clk3_a,
-	[RPM_SMD_CNOC_CLK] = &clk_smd_rpm_bus_1_cnoc_clk,
-	[RPM_SMD_CNOC_A_CLK] = &clk_smd_rpm_bus_1_cnoc_a_clk,
 	[RPM_SMD_IPA_CLK] = &clk_smd_rpm_ipa_clk,
 	[RPM_SMD_IPA_A_CLK] = &clk_smd_rpm_ipa_a_clk,
-	[RPM_SMD_QUP_CLK] = &clk_smd_rpm_qup_clk,
-	[RPM_SMD_QUP_A_CLK] = &clk_smd_rpm_qup_a_clk,
-	[RPM_SMD_MMRT_CLK] = &clk_smd_rpm_mmrt_clk,
-	[RPM_SMD_MMRT_A_CLK] = &clk_smd_rpm_mmrt_a_clk,
-	[RPM_SMD_MMNRT_CLK] = &clk_smd_rpm_mmnrt_clk,
-	[RPM_SMD_MMNRT_A_CLK] = &clk_smd_rpm_mmnrt_a_clk,
 	[RPM_SMD_SNOC_PERIPH_CLK] = &clk_smd_rpm_bus_0_snoc_periph_clk,
 	[RPM_SMD_SNOC_PERIPH_A_CLK] = &clk_smd_rpm_bus_0_snoc_periph_a_clk,
 	[RPM_SMD_SNOC_LPASS_CLK] = &clk_smd_rpm_bus_5_snoc_lpass_clk,
@@ -1249,6 +1190,8 @@ static struct clk_smd_rpm *qcm2290_clks[] = {
 static const struct rpm_smd_clk_desc rpm_clk_qcm2290 = {
 	.clks = qcm2290_clks,
 	.num_clks = ARRAY_SIZE(qcm2290_clks),
+	.icc_clks = sm_qnoc_icc_clks,
+	.num_icc_clks = ARRAY_SIZE(sm_qnoc_icc_clks)
 };
 
 static const struct of_device_id rpm_smd_clk_match_table[] = {
@@ -1332,6 +1275,15 @@ static int rpm_smd_clk_probe(struct platform_device *pdev)
 			goto err;
 	}
 
+	for (i = 0; i < desc->num_icc_clks; i++) {
+		if (!desc->icc_clks[i])
+			continue;
+
+		ret = clk_smd_rpm_handoff(desc->icc_clks[i]);
+		if (ret)
+			goto err;
+	}
+
 	if (!desc->scaling_before_handover) {
 		ret = clk_smd_rpm_enable_scaling();
 		if (ret)

-- 
2.41.0

[PATCH v5 19/22] interconnect: qcom: icc-rpm: Fix bucket number

[Konrad Dybcio]

SMD RPM only provides two buckets, one each for the active-only and
active-sleep RPM contexts. Use the correct constant to allocate and
operate on them.

This will make the qcom,icc.h header no longer work with this driver,
mostly because.. it was never meant to! The commit that introduced
bucket support to SMD RPM was trying to shove a square into a round
hole and it did not work out very well. That said, there are no
active users of SMD RPM ICC + qcom,icc.h, so that doesn't hurt.

Fixes: dcbce7b0a79c ("interconnect: qcom: icc-rpm: Support multiple buckets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c | 16 ++++++++--------
 drivers/interconnect/qcom/icc-rpm.h |  6 +++---
 2 files changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index 858880a97d2a..47d034284e0d 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -249,7 +249,7 @@ static void qcom_icc_pre_bw_aggregate(struct icc_node *node)
 	size_t i;
 
 	qn = node->data;
-	for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++) {
+	for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++) {
 		qn->sum_avg[i] = 0;
 		qn->max_peak[i] = 0;
 	}
@@ -273,9 +273,9 @@ static int qcom_icc_bw_aggregate(struct icc_node *node, u32 tag, u32 avg_bw,
 	qn = node->data;
 
 	if (!tag)
-		tag = QCOM_ICC_TAG_ALWAYS;
+		tag = RPM_ALWAYS_TAG;
 
-	for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++) {
+	for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++) {
 		if (tag & BIT(i)) {
 			qn->sum_avg[i] += avg_bw;
 			qn->max_peak[i] = max_t(u32, qn->max_peak[i], peak_bw);
@@ -300,11 +300,11 @@ static void qcom_icc_bus_aggregate(struct icc_provider *provider,
 {
 	struct icc_node *node;
 	struct qcom_icc_node *qn;
-	u64 sum_avg[QCOM_ICC_NUM_BUCKETS];
+	u64 sum_avg[QCOM_SMD_RPM_STATE_NUM];
 	int i;
 
 	/* Initialise aggregate values */
-	for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++) {
+	for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++) {
 		agg_avg[i] = 0;
 		agg_peak[i] = 0;
 	}
@@ -317,7 +317,7 @@ static void qcom_icc_bus_aggregate(struct icc_provider *provider,
 	 */
 	list_for_each_entry(node, &provider->nodes, node_list) {
 		qn = node->data;
-		for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++) {
+		for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++) {
 			if (qn->channels)
 				sum_avg[i] = div_u64(qn->sum_avg[i], qn->channels);
 			else
@@ -328,7 +328,7 @@ static void qcom_icc_bus_aggregate(struct icc_provider *provider,
 	}
 
 	/* Find maximum values across all buckets */
-	for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++)
+	for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++)
 		*max_agg_avg = max_t(u64, *max_agg_avg, agg_avg[i]);
 }
 
@@ -339,7 +339,7 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 	struct icc_provider *provider;
 	u64 sum_bw;
 	u64 active_rate, sleep_rate;
-	u64 agg_avg[QCOM_ICC_NUM_BUCKETS], agg_peak[QCOM_ICC_NUM_BUCKETS];
+	u64 agg_avg[QCOM_SMD_RPM_STATE_NUM], agg_peak[QCOM_SMD_RPM_STATE_NUM];
 	u64 max_agg_avg;
 	int ret;
 
diff --git a/drivers/interconnect/qcom/icc-rpm.h b/drivers/interconnect/qcom/icc-rpm.h
index d5da24495d14..f73d35f3d32a 100644
--- a/drivers/interconnect/qcom/icc-rpm.h
+++ b/drivers/interconnect/qcom/icc-rpm.h
@@ -10,7 +10,7 @@
 #include <linux/platform_device.h>
 #include <linux/soc/qcom/smd-rpm.h>
 
-#include <dt-bindings/interconnect/qcom,icc.h>
+#include <dt-bindings/interconnect/qcom,rpm-icc.h>
 
 #define RPM_BUS_MASTER_REQ	0x73616d62
 #define RPM_BUS_SLAVE_REQ	0x766c7362
@@ -105,8 +105,8 @@ struct qcom_icc_node {
 	u16 num_links;
 	u16 channels;
 	u16 buswidth;
-	u64 sum_avg[QCOM_ICC_NUM_BUCKETS];
-	u64 max_peak[QCOM_ICC_NUM_BUCKETS];
+	u64 sum_avg[QCOM_SMD_RPM_STATE_NUM];
+	u64 max_peak[QCOM_SMD_RPM_STATE_NUM];
 	int mas_rpm_id;
 	int slv_rpm_id;
 	struct qcom_icc_qos qos;

-- 
2.41.0

[PATCH v5 20/22] interconnect: qcom: icc-rpm: Set bandwidth on both contexts

[Konrad Dybcio]

Up until now, for some reason we've only been setting bandwidth values
on the active-only context. That pretty much meant that RPM could lift
all votes when entering sleep mode. Or never sleep at all.

That in turn could potentially break things like USB wakeup, as the
connection between APSS and SNoC/PNoC would simply be dead.

Set the values appropriately.

Fixes: 30c8fa3ec61a ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c | 54 +++++++++++++++++++------------------
 1 file changed, 28 insertions(+), 26 deletions(-)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index 47d034284e0d..ac84fe0bc852 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -205,34 +205,39 @@ static int qcom_icc_qos_set(struct icc_node *node)
 	}
 }
 
-static int qcom_icc_rpm_set(struct qcom_icc_node *qn, u64 sum_bw)
+static int qcom_icc_rpm_set(struct qcom_icc_node *qn, u64 *bw)
 {
-	int ret = 0;
+	int ret, rpm_ctx = 0;
+	u64 bw_bps;
 
 	if (qn->qos.ap_owned)
 		return 0;
 
-	if (qn->mas_rpm_id != -1) {
-		ret = qcom_icc_rpm_smd_send(QCOM_SMD_RPM_ACTIVE_STATE,
-					    RPM_BUS_MASTER_REQ,
-					    qn->mas_rpm_id,
-					    sum_bw);
-		if (ret) {
-			pr_err("qcom_icc_rpm_smd_send mas %d error %d\n",
-			       qn->mas_rpm_id, ret);
-			return ret;
+	for (rpm_ctx = 0; rpm_ctx < QCOM_SMD_RPM_STATE_NUM; rpm_ctx++) {
+		bw_bps = icc_units_to_bps(bw[rpm_ctx]);
+
+		if (qn->mas_rpm_id != -1) {
+			ret = qcom_icc_rpm_smd_send(rpm_ctx,
+						    RPM_BUS_MASTER_REQ,
+						    qn->mas_rpm_id,
+						    bw_bps);
+			if (ret) {
+				pr_err("qcom_icc_rpm_smd_send mas %d error %d\n",
+				qn->mas_rpm_id, ret);
+				return ret;
+			}
 		}
-	}
 
-	if (qn->slv_rpm_id != -1) {
-		ret = qcom_icc_rpm_smd_send(QCOM_SMD_RPM_ACTIVE_STATE,
-					    RPM_BUS_SLAVE_REQ,
-					    qn->slv_rpm_id,
-					    sum_bw);
-		if (ret) {
-			pr_err("qcom_icc_rpm_smd_send slv %d error %d\n",
-			       qn->slv_rpm_id, ret);
-			return ret;
+		if (qn->slv_rpm_id != -1) {
+			ret = qcom_icc_rpm_smd_send(rpm_ctx,
+						    RPM_BUS_SLAVE_REQ,
+						    qn->slv_rpm_id,
+						    bw_bps);
+			if (ret) {
+				pr_err("qcom_icc_rpm_smd_send slv %d error %d\n",
+				qn->slv_rpm_id, ret);
+				return ret;
+			}
 		}
 	}
 
@@ -337,7 +342,6 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 	struct qcom_icc_provider *qp;
 	struct qcom_icc_node *src_qn = NULL, *dst_qn = NULL;
 	struct icc_provider *provider;
-	u64 sum_bw;
 	u64 active_rate, sleep_rate;
 	u64 agg_avg[QCOM_SMD_RPM_STATE_NUM], agg_peak[QCOM_SMD_RPM_STATE_NUM];
 	u64 max_agg_avg;
@@ -351,14 +355,12 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 
 	qcom_icc_bus_aggregate(provider, agg_avg, agg_peak, &max_agg_avg);
 
-	sum_bw = icc_units_to_bps(max_agg_avg);
-
-	ret = qcom_icc_rpm_set(src_qn, sum_bw);
+	ret = qcom_icc_rpm_set(src_qn, agg_avg);
 	if (ret)
 		return ret;
 
 	if (dst_qn) {
-		ret = qcom_icc_rpm_set(dst_qn, sum_bw);
+		ret = qcom_icc_rpm_set(dst_qn, agg_avg);
 		if (ret)
 			return ret;
 	}

-- 
2.41.0

[PATCH v5 21/22] interconnect: qcom: icc-rpm: Set correct bandwidth through RPM bw req

[Konrad Dybcio]

Currently, we're setting the aggregated-on-provider bandwidth on each
node, individually. That is of course incorrect and results in far too
high votes. Use the correct values to ensure we're not wasting power.

Fixes: 30c8fa3ec61a ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index ac84fe0bc852..b7e0dfbdd26d 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -355,12 +355,12 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 
 	qcom_icc_bus_aggregate(provider, agg_avg, agg_peak, &max_agg_avg);
 
-	ret = qcom_icc_rpm_set(src_qn, agg_avg);
+	ret = qcom_icc_rpm_set(src_qn, src_qn->sum_avg);
 	if (ret)
 		return ret;
 
 	if (dst_qn) {
-		ret = qcom_icc_rpm_set(dst_qn, agg_avg);
+		ret = qcom_icc_rpm_set(dst_qn, dst_qn->sum_avg);
 		if (ret)
 			return ret;
 	}

-- 
2.41.0

[PATCH v5 22/22] interconnect: qcom: icc-rpm: Fix bandwidth calculations

[Konrad Dybcio]

Up until now, we've been aggregating the bandwidth values and only
dividing them by the bus width of the source node. This was completely
wrong, as different nodes on a given path may (and usually do) have
varying bus widths.  That in turn, resulted in the calculated clock rates
being completely bogus - usually they ended up being much higher, as
NoC_A<->NoC_B links are very wide.

Since we're not using the aggregate bandwidth value for anything other
than clock rate calculations, remodel qcom_icc_bus_aggregate() to
calculate the per-context clock rate for a given provider, taking into
account the bus width of every individual node.

Fixes: 30c8fa3ec61a ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/interconnect/qcom/icc-rpm.c | 59 ++++++++++++-------------------------
 1 file changed, 19 insertions(+), 40 deletions(-)

diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
index b7e0dfbdd26d..4ab410e477ce 100644
--- a/drivers/interconnect/qcom/icc-rpm.c
+++ b/drivers/interconnect/qcom/icc-rpm.c
@@ -293,58 +293,44 @@ static int qcom_icc_bw_aggregate(struct icc_node *node, u32 tag, u32 avg_bw,
 }
 
 /**
- * qcom_icc_bus_aggregate - aggregate bandwidth by traversing all nodes
+ * qcom_icc_bus_aggregate - calculate bus clock rates by traversing all nodes
  * @provider: generic interconnect provider
- * @agg_avg: an array for aggregated average bandwidth of buckets
- * @agg_peak: an array for aggregated peak bandwidth of buckets
- * @max_agg_avg: pointer to max value of aggregated average bandwidth
+ * @agg_clk_rate: array containing the aggregated clock rates in kHz
  */
-static void qcom_icc_bus_aggregate(struct icc_provider *provider,
-				   u64 *agg_avg, u64 *agg_peak,
-				   u64 *max_agg_avg)
+static void qcom_icc_bus_aggregate(struct icc_provider *provider, u64 *agg_clk_rate)
 {
-	struct icc_node *node;
+	u64 agg_avg_rate, agg_rate;
 	struct qcom_icc_node *qn;
-	u64 sum_avg[QCOM_SMD_RPM_STATE_NUM];
+	struct icc_node *node;
 	int i;
 
-	/* Initialise aggregate values */
-	for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++) {
-		agg_avg[i] = 0;
-		agg_peak[i] = 0;
-	}
-
-	*max_agg_avg = 0;
-
 	/*
-	 * Iterate nodes on the interconnect and aggregate bandwidth
-	 * requests for every bucket.
+	 * Iterate nodes on the provider, aggregate bandwidth requests for
+	 * every bucket and convert them into bus clock rates.
 	 */
 	list_for_each_entry(node, &provider->nodes, node_list) {
 		qn = node->data;
 		for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++) {
 			if (qn->channels)
-				sum_avg[i] = div_u64(qn->sum_avg[i], qn->channels);
+				agg_avg_rate = div_u64(qn->sum_avg[i], qn->channels);
 			else
-				sum_avg[i] = qn->sum_avg[i];
-			agg_avg[i] += sum_avg[i];
-			agg_peak[i] = max_t(u64, agg_peak[i], qn->max_peak[i]);
+				agg_avg_rate = qn->sum_avg[i];
+
+			agg_rate = max_t(u64, agg_avg_rate, qn->max_peak[i]);
+			do_div(agg_rate, qn->buswidth);
+
+			agg_clk_rate[i] = max_t(u64, agg_clk_rate[i], agg_rate);
 		}
 	}
-
-	/* Find maximum values across all buckets */
-	for (i = 0; i < QCOM_SMD_RPM_STATE_NUM; i++)
-		*max_agg_avg = max_t(u64, *max_agg_avg, agg_avg[i]);
 }
 
 static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 {
-	struct qcom_icc_provider *qp;
 	struct qcom_icc_node *src_qn = NULL, *dst_qn = NULL;
+	u64 agg_clk_rate[QCOM_SMD_RPM_STATE_NUM] = { 0 };
 	struct icc_provider *provider;
+	struct qcom_icc_provider *qp;
 	u64 active_rate, sleep_rate;
-	u64 agg_avg[QCOM_SMD_RPM_STATE_NUM], agg_peak[QCOM_SMD_RPM_STATE_NUM];
-	u64 max_agg_avg;
 	int ret;
 
 	src_qn = src->data;
@@ -353,7 +339,9 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 	provider = src->provider;
 	qp = to_qcom_provider(provider);
 
-	qcom_icc_bus_aggregate(provider, agg_avg, agg_peak, &max_agg_avg);
+	qcom_icc_bus_aggregate(provider, agg_clk_rate);
+	active_rate = agg_clk_rate[QCOM_SMD_RPM_ACTIVE_STATE];
+	sleep_rate = agg_clk_rate[QCOM_SMD_RPM_SLEEP_STATE];
 
 	ret = qcom_icc_rpm_set(src_qn, src_qn->sum_avg);
 	if (ret)
@@ -369,15 +357,6 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
 	if (!qp->bus_clk_desc && !qp->bus_clk)
 		return 0;
 
-	/* Intentionally keep the rates in kHz as that's what RPM accepts */
-	active_rate = max(agg_avg[QCOM_SMD_RPM_ACTIVE_STATE],
-			  agg_peak[QCOM_SMD_RPM_ACTIVE_STATE]);
-	do_div(active_rate, src_qn->buswidth);
-
-	sleep_rate = max(agg_avg[QCOM_SMD_RPM_SLEEP_STATE],
-			 agg_peak[QCOM_SMD_RPM_SLEEP_STATE]);
-	do_div(sleep_rate, src_qn->buswidth);
-
 	/*
 	 * Downstream checks whether the requested rate is zero, but it makes little sense
 	 * to vote for a value that's below the lower threshold, so let's not do so.

-- 
2.41.0