r8169 won't transmit with 3.12

r8169 won't transmit with 3.12

[Craig Small]

Hi,
  I seem to be having lots of troubles with the RealTek chipsets. I have
one onboard and two PCI-e cards and they all have the same problem. They
will not transmit anything.  The r8169 driver does it, as does the 
r8168-dkms module.

It's a new setup so it might of never worked. It's not likely to be a
hardware problem as its three different devices.

I've sent what I think you might need for starters, but if there
is extra stuff you'd like to see, let me know.

I'm using a stock Debian kernel
3.12-1-amd64 #1 SMP Debian 3.12.6-2 (2013-12-29)

I've included the lspci output of one of the cards below. I'm not
really sure what else you'd need to check things.

The problem shows up the same, the TX dropped counter increments.
I'm not sure why 42 packets made it out (or even if they really did)
Receive works fine, I can even start up wireshark and see packets
pass by.

eth0      Link encap:Ethernet  HWaddr 00:e0:4c:80:66:57  
          inet addr:192.168.1.222  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::2e0:4cff:fe80:6657/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8252 errors:0 dropped:0 overruns:0 frame:0
          TX packets:42 errors:0 dropped:8029 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:584930 (571.2 KiB)  TX bytes:5083 (4.9 KiB)

ethtool -S shows a similar story, not sure if the rx_missed counter
is another problem:
NIC statistics:
     tx_packets: 47
     rx_packets: 31342
     tx_errors: 0
     rx_errors: 0
     rx_missed: 47438
     align_errors: 0
     tx_single_collisions: 0
     tx_multi_collisions: 0
     unicast: 1
     broadcast: 29638
     multicast: 1891
     tx_aborted: 0
     tx_underrun: 0

I've disabled the on-board device now, but the simple lspci output was:
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)

The PCI-e cards have the following:

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 02)
	Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 73
	Region 0: I/O ports at d000 [size=256]
	Region 2: Memory at fde00000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at d2200000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at d2210000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee3f00c  Data: 4123
	Capabilities: [70] Express (v1) Endpoint, MSI 08
		DevCap:	MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <128ns, L1 unlimited
			ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend+
		LnkCap:	Port #16, Speed unknown, Width x22, ASPM not supported, Exit Latency L0s <64ns, L1 <2us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [b0] MSI-X: Enable- Count=2 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Unknown small resource type 05, will not decode more.
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=01
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
	Kernel driver in use: r8169

-- 
Craig Small (@smallsees)   http://enc.com.au/       csmall at : enc.com.au
Debian GNU/Linux           http://www.debian.org/   csmall at : debian.org
GPG fingerprint:        5D2F B320 B825 D939 04D2  0519 3938 F96B DF50 FEA5

Re: r8169 won't transmit with 3.12

[Francois Romieu]

Craig Small <csmall@enc.com.au> :
[...]
> It's a new setup so it might of never worked. It's not likely to be a
> hardware problem as its three different devices.

You may check that the onboard nic device does not even work when the
extra PCI-e card aren't plugged.

> I've sent what I think you might need for starters, but if there
> is extra stuff you'd like to see, let me know.

A complete dmesg including the XID lines that the r8169 driver prints
would be welcome.

> The problem shows up the same, the TX dropped counter increments.
> I'm not sure why 42 packets made it out (or even if they really did)
> Receive works fine, I can even start up wireshark and see packets
> pass by.
> 
> eth0      Link encap:Ethernet  HWaddr 00:e0:4c:80:66:57  
>           inet addr:192.168.1.222  Bcast:192.168.1.255  Mask:255.255.255.0
>           inet6 addr: fe80::2e0:4cff:fe80:6657/64 Scope:Link
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:8252 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:42 errors:0 dropped:8029 overruns:0 carrier:0

There are very few places where the r8169 driver modifies tx_dropped.

Please increase the driver verbosity with the 'msglvl' option of ethtool.

[...]
> ethtool -S shows a similar story, not sure if the rx_missed counter
> is another problem:

It seems safe to ignore as long as it does not change after startup.

-- 
Ueimor

Re: r8169 won't transmit with 3.12

[Craig Small]

[-- Attachment #1: Type: text/plain, Size: 1883 bytes --]

Hi,
  Thanks for looking into this.
On Wed, Jan 22, 2014 at 12:36:30AM +0100, Francois Romieu wrote:
> You may check that the onboard nic device does not even work when the
> extra PCI-e card aren't plugged.
It definitely doesn't. I've tried with only the onboard device
and no other NIC device (r8169 or not) installed and its the same
problem.

> A complete dmesg including the XID lines that the r8169 driver prints
> would be welcome.
See attached text file. I'm not sure why I get so many interface up
messages. This is for the two NIC cards. I can pull them out and go back
to the onboard one if you like.

I don't see that transmit queue timeout message that often. It looks
like it might happen once per boot and then giveup.

> Please increase the driver verbosity with the 'msglvl' option of ethtool.
I set it at 65535 but it didn't seem to make much difference.

If I:
  * rmmod r8169
  * modprobe r8169 debug=1
  * ifconfig eth0 ....
  * ethtool -s eth0 msglvl 65535
  * ping -I eth0 ...
I get the following:

[1256123.142885] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[1256123.142905] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[1256123.143182] r8169 0000:03:00.0: irq 73 for MSI/MSI-X
[1256123.154873] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[1256123.154896] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
[1256123.155148] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
[1256182.169596] r8169 0000:03:00.0 eth0: link down
[1256182.169618] r8169 0000:03:00.0 eth0: link down
[1256185.546908] r8169 0000:03:00.0 eth0: link up
[1256228.041490] r8169 0000:03:00.0 eth0: link up

 - Craig
-- 
Craig Small (@smallsees)   http://enc.com.au/       csmall at : enc.com.au
Debian GNU/Linux           http://www.debian.org/   csmall at : debian.org
GPG fingerprint:        5D2F B320 B825 D939 04D2  0519 3938 F96B DF50 FEA5

[-- Attachment #2: r8169dmesg.txt --]
[-- Type: text/plain, Size: 28914 bytes --]

Jan  7 21:13:52 elmo kernel: [    0.924084] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:13:52 elmo kernel: [    0.924100] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:13:52 elmo kernel: [    0.924315] r8169 0000:03:00.0: irq 72 for MSI/MSI-X
Jan  7 21:13:52 elmo kernel: [    0.924474] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001820000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 72
Jan  7 21:13:52 elmo kernel: [    0.924477] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:13:52 elmo kernel: [    0.925663] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:13:52 elmo kernel: [    0.925678] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:13:52 elmo kernel: [    0.925983] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
Jan  7 21:13:52 elmo kernel: [    0.926424] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc90001870000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 74
Jan  7 21:13:52 elmo kernel: [    0.926427] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:13:54 elmo kernel: [   22.478851] r8169 0000:03:00.0 eth2: link down
Jan  7 21:13:54 elmo kernel: [   22.498863] r8169 0000:06:00.0 eth3: link down
Jan  7 21:21:57 elmo kernel: [    0.921374] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:21:57 elmo kernel: [    0.921385] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:21:57 elmo kernel: [    0.921559] r8169 0000:03:00.0: irq 73 for MSI/MSI-X
Jan  7 21:21:57 elmo kernel: [    0.921724] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001824000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 73
Jan  7 21:21:57 elmo kernel: [    0.921730] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:21:57 elmo kernel: [    0.924400] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:21:57 elmo kernel: [    0.924411] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:21:57 elmo kernel: [    0.924593] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
Jan  7 21:21:57 elmo kernel: [    0.924745] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc9000187c000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 74
Jan  7 21:21:57 elmo kernel: [    0.924747] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:21:57 elmo kernel: [   20.188523] r8169 0000:06:00.0 eth1: link down
Jan  7 21:21:58 elmo kernel: [   43.722301] r8169 0000:03:00.0 eth0: link down
Jan  7 21:31:36 elmo kernel: [    0.920953] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:31:36 elmo kernel: [    0.920965] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:31:36 elmo kernel: [    0.921184] r8169 0000:03:00.0: irq 72 for MSI/MSI-X
Jan  7 21:31:36 elmo kernel: [    0.921329] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001820000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 72
Jan  7 21:31:36 elmo kernel: [    0.921332] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:31:36 elmo kernel: [    0.921407] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:31:36 elmo kernel: [    0.921414] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:31:36 elmo kernel: [    0.921586] r8169 0000:06:00.0: irq 73 for MSI/MSI-X
Jan  7 21:31:36 elmo kernel: [    0.921719] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc90001824000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 73
Jan  7 21:31:36 elmo kernel: [    0.921722] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:31:36 elmo kernel: [   20.712240] r8169 0000:03:00.0 eth0: link down
Jan  7 21:31:36 elmo kernel: [   20.712321] r8169 0000:03:00.0 eth0: link down
Jan  7 21:31:36 elmo kernel: [   23.934160] r8169 0000:03:00.0 eth0: link up
Jan  7 21:31:36 elmo kernel: [   51.528553] r8169 0000:06:00.0 eth1: link down
Jan  7 21:31:36 elmo kernel: [   51.528628] r8169 0000:06:00.0 eth1: link down
Jan  7 21:31:36 elmo kernel: [   53.825413] NETDEV WATCHDOG: eth0 (r8169): transmit queue 0 timed out
Jan  7 21:31:36 elmo kernel: [   53.825416] Modules linked in: ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipt_REJECT xt_tcpudp xt_LOG xt_mac nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables x_tables fuse it87 hwmon_vid loop tda18271 tda10048 joydev hid_generic snd_hda_codec_hdmi usbhid hid evdev kvm_amd kvm crc32_pclmul crc32c_intel ghash_clmulni_intel raid1 aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper md_mod psmouse sp5100_tco pcspkr fam15h_power serio_raw edac_mce_amd edac_core k10temp i2c_piix4 nouveau snd_hda_codec_via mxm_wmi wmi saa7164 video ttm drm_kms_helper tveeprom dvb_core snd_hda_intel v4l2_common drm snd_hda_codec videodev snd_hwdep media snd_pcm i2c_algo_bit snd_page_alloc acpi_cpufreq i2c_core snd_timer snd button processor soundcore thermal_sys ext4 crc16 mbcache jbd2 dm_mod sg sd_mod sr_mod cdrom crc_t10dif crct10dif_common ahci libahci ehci_pci libata ohci_pci ohci_hcd ehci_hcd xhci_hcd scsi_mod r8169 mii usbcore usb_common
Jan  7 21:31:36 elmo kernel: [   53.857677] r8169 0000:03:00.0 eth0: link up
Jan  7 21:31:36 elmo kernel: [   54.324015] r8169 0000:06:00.0 eth1: link up
Jan  7 21:31:37 elmo kernel: [   83.826545] r8169 0000:03:00.0 eth0: link up
Jan  7 21:31:44 elmo kernel: [   90.822740] r8169 0000:06:00.0 eth1: link up
Jan  7 21:31:49 elmo kernel: [   95.822969] r8169 0000:03:00.0 eth0: link up
Jan  7 21:32:01 elmo kernel: [  107.832103] r8169 0000:03:00.0 eth0: link up
Jan  7 21:32:02 elmo kernel: [  108.807299] r8169 0000:06:00.0 eth1: link up
Jan  7 21:32:13 elmo kernel: [  119.816649] r8169 0000:03:00.0 eth0: link up
Jan  7 21:32:25 elmo kernel: [  131.813620] r8169 0000:03:00.0 eth0: link up
Jan  7 21:32:55 elmo kernel: [  161.774516] r8169 0000:03:00.0 eth0: link up
Jan  7 21:33:13 elmo kernel: [  179.768739] r8169 0000:03:00.0 eth0: link up
Jan  7 21:33:37 elmo kernel: [  203.758175] r8169 0000:03:00.0 eth0: link up
Jan  7 21:34:19 elmo kernel: [  245.709869] r8169 0000:03:00.0 eth0: link up
Jan  7 21:35:01 elmo kernel: [  287.693507] r8169 0000:03:00.0 eth0: link up
Jan  7 21:35:31 elmo kernel: [  317.654398] r8169 0000:03:00.0 eth0: link up
Jan  7 21:36:01 elmo kernel: [  347.647293] r8169 0000:03:00.0 eth0: link up
Jan  7 21:36:37 elmo kernel: [  383.606973] r8169 0000:03:00.0 eth0: link up
Jan  7 21:37:01 elmo kernel: [  407.633061] r8169 0000:03:00.0 eth0: link up
Jan  7 21:37:19 elmo kernel: [  425.571252] r8169 0000:03:00.0 eth0: link up
Jan  7 21:38:47 elmo kernel: [  513.921118] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:38:47 elmo kernel: [  513.921136] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:38:47 elmo kernel: [  513.921421] r8169 0000:03:00.0: irq 72 for MSI/MSI-X
Jan  7 21:38:47 elmo kernel: [  513.921795] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001820000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 72
Jan  7 21:38:47 elmo kernel: [  513.921802] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:38:47 elmo kernel: [  513.927502] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:38:47 elmo kernel: [  513.927525] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:38:47 elmo kernel: [  513.927767] r8169 0000:06:00.0: irq 73 for MSI/MSI-X
Jan  7 21:38:47 elmo kernel: [  513.928204] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc90001824000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 73
Jan  7 21:38:47 elmo kernel: [  513.928211] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:39:08 elmo kernel: [  534.217262] r8169 0000:03:00.0 eth0: link down
Jan  7 21:39:08 elmo kernel: [  534.217274] r8169 0000:03:00.0 eth0: link down
Jan  7 21:39:11 elmo kernel: [  537.473818] r8169 0000:03:00.0 eth0: link up
Jan  7 21:39:23 elmo kernel: [  549.508735] r8169 0000:03:00.0 eth0: link up
Jan  7 21:39:35 elmo kernel: [  561.479471] r8169 0000:03:00.0 eth0: link up
Jan  7 21:39:53 elmo kernel: [  579.541748] r8169 0000:03:00.0 eth0: link up
Jan  7 21:40:29 elmo kernel: [  615.580750] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:40:29 elmo kernel: [  615.580771] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:40:29 elmo kernel: [  615.581034] r8169 0000:03:00.0: irq 72 for MSI/MSI-X
Jan  7 21:40:29 elmo kernel: [  615.586376] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:40:29 elmo kernel: [  615.586395] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:40:29 elmo kernel: [  615.586632] r8169 0000:06:00.0: irq 73 for MSI/MSI-X
Jan  7 21:45:36 elmo kernel: [    0.924701] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:45:36 elmo kernel: [    0.924807] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:45:36 elmo kernel: [    0.925414] r8169 0000:03:00.0: irq 72 for MSI/MSI-X
Jan  7 21:45:36 elmo kernel: [    0.925768] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001820000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 72
Jan  7 21:45:36 elmo kernel: [    0.925771] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:45:36 elmo kernel: [    0.925797] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  7 21:45:36 elmo kernel: [    0.925804] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  7 21:45:36 elmo kernel: [    0.925981] r8169 0000:06:00.0: irq 73 for MSI/MSI-X
Jan  7 21:45:36 elmo kernel: [    0.926099] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc90001824000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 73
Jan  7 21:45:36 elmo kernel: [    0.926101] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  7 21:45:36 elmo kernel: [   21.831549] r8169 0000:03:00.0 eth0: link down
Jan  7 21:45:44 elmo kernel: [   42.735362] r8169 0000:06:00.0 eth1: link down
Jan  7 21:45:44 elmo kernel: [   42.735371] r8169 0000:06:00.0 eth1: link down
Jan  7 21:45:47 elmo kernel: [   45.491721] r8169 0000:06:00.0 eth1: link up
Jan  7 21:47:59 elmo kernel: [  177.794729] NETDEV WATCHDOG: eth1 (r8169): transmit queue 0 timed out
Jan  7 21:47:59 elmo kernel: [  177.794732] Modules linked in: ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 bnep rfcomm bluetooth rfkill vhost_net vhost macvtap macvlan tun ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_CHECKSUM iptable_mangle bridge stp llc xt_multiport ip6table_filter ip6_tables ebtable_nat ebtables parport_pc ppdev lp parport binfmt_misc ipt_REJECT xt_tcpudp xt_LOG xt_mac nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables x_tables fuse it87 hwmon_vid loop tda18271 tda10048 joydev hid_generic snd_hda_codec_hdmi usbhid hid evdev raid1 md_mod kvm_amd kvm crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper psmouse pcspkr serio_raw k10temp edac_mce_amd fam15h_power sp5100_tco edac_core nouveau snd_hda_codec_via i2c_piix4 mxm_wmi saa7164 wmi video ttm tveeprom drm_kms_helper dvb_core v4l2_common drm videodev media i2c_algo_bit snd_hda_intel i2c_core snd_hda_codec acpi_cpufreq snd_hwdep processor button snd_pcm snd_page_alloc snd_timer thermal_sys snd soundcore ext4 crc16 mbcache jbd2 dm_mod sg sd_mod sr_mod cdrom crc_t10dif crct10dif_common 8139too ehci_pci ahci ohci_pci ohci_hcd ehci_hcd libahci xhci_hcd r8169 mii usbcore libata usb_common scsi_mod
Jan  7 21:47:59 elmo kernel: [  177.803038] r8169 0000:06:00.0 eth1: link up
Jan  7 21:55:13 elmo kernel: [  611.228156] Modules linked in: r8168(O) ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 bnep rfcomm bluetooth rfkill vhost_net vhost macvtap macvlan tun ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_CHECKSUM iptable_mangle bridge stp llc xt_multiport ip6table_filter ip6_tables ebtable_nat ebtables parport_pc ppdev lp parport binfmt_misc ipt_REJECT xt_tcpudp xt_LOG xt_mac nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables x_tables fuse it87 hwmon_vid loop tda18271 tda10048 joydev hid_generic snd_hda_codec_hdmi usbhid hid evdev raid1 md_mod kvm_amd kvm crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper psmouse pcspkr serio_raw k10temp edac_mce_amd fam15h_power sp5100_tco edac_core nouveau snd_hda_codec_via i2c_piix4 mxm_wmi saa7164 wmi video ttm tveeprom drm_kms_helper dvb_core v4l2_common drm videodev media i2c_algo_bit snd_hda_intel i2c_core snd_hda_codec acpi_cpufreq snd_hwdep processor button snd_pcm snd_page_alloc snd_timer thermal_sys snd soundcore ext4 crc16 mbcache jbd2 dm_mod sg sd_mod sr_mod cdrom crc_t10dif crct10dif_common 8139too ehci_pci ahci ohci_pci ohci_hcd ehci_hcd libahci xhci_hcd mii usbcore libata usb_common scsi_mod [last unloaded: r8169]
Jan  9 08:52:26 elmo kernel: [124556.014238] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  9 08:52:26 elmo kernel: [124556.014257] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 08:52:26 elmo kernel: [124556.014508] r8169 0000:03:00.0: irq 73 for MSI/MSI-X
Jan  9 08:52:26 elmo kernel: [124556.014791] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001870000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 73
Jan  9 08:52:26 elmo kernel: [124556.014799] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 08:52:26 elmo kernel: [124556.014984] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  9 08:52:26 elmo kernel: [124556.015001] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 08:52:26 elmo kernel: [124556.015248] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
Jan  9 08:52:26 elmo kernel: [124556.015509] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc9000187e000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 74
Jan  9 08:52:26 elmo kernel: [124556.015515] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 08:52:26 elmo kernel: [124556.056527] r8169 0000:03:00.0 eth0: link down
Jan  9 08:52:27 elmo kernel: [124557.661174] r8169 0000:03:00.0 eth0: link up
Jan  9 08:52:52 elmo kernel: [124582.349643] r8169 0000:03:00.0 eth0: link up
Jan  9 08:53:46 elmo kernel: [124636.305529] r8169 0000:03:00.0 eth0: link up
Jan  9 08:54:36 elmo kernel: [124686.536235] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  9 08:54:36 elmo kernel: [124686.536260] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 08:54:36 elmo kernel: [124686.536512] r8169 0000:03:00.0: irq 73 for MSI/MSI-X
Jan  9 08:54:36 elmo kernel: [124686.536805] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001870000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 73
Jan  9 08:54:36 elmo kernel: [124686.536812] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 08:54:36 elmo kernel: [124686.547745] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Jan  9 08:54:36 elmo kernel: [124686.547769] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 08:54:36 elmo kernel: [124686.548024] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
Jan  9 08:54:36 elmo kernel: [124686.555383] r8169 0000:03:00.0 eth0: link down
Jan  9 08:54:36 elmo kernel: [124686.555396] r8169 0000:03:00.0 eth0: link down
Jan  9 08:54:36 elmo kernel: [124686.555635] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc9000187e000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 74
Jan  9 08:54:36 elmo kernel: [124686.555640] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 08:54:40 elmo kernel: [124690.143434] r8169 0000:03:00.0 eth0: link up
Jan  9 08:55:40 elmo kernel: [124750.245190] r8169 0000:03:00.0 eth0: link up
Jan  9 08:56:28 elmo kernel: [124798.267925] r8169 0000:03:00.0 eth0: link up
Jan  9 08:58:16 elmo kernel: [124906.124315] r8169 0000:03:00.0 eth0: link up
Jan  9 09:00:34 elmo kernel: [125043.447578] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 09:00:34 elmo kernel: [125043.447833] r8169 0000:03:00.0: irq 73 for MSI/MSI-X
Jan  9 09:00:34 elmo kernel: [125043.448156] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001870000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 73
Jan  9 09:00:34 elmo kernel: [125043.448162] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 09:00:34 elmo kernel: [125043.460502] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 09:00:34 elmo kernel: [125043.460705] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
Jan  9 09:00:34 elmo kernel: [125043.467175] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc9000187e000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 74
Jan  9 09:00:34 elmo kernel: [125043.467181] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 09:09:00 elmo kernel: [125549.128197] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 09:09:00 elmo kernel: [125549.128457] r8169 0000:03:00.0: irq 73 for MSI/MSI-X
Jan  9 09:09:00 elmo kernel: [125549.128748] r8169 0000:03:00.0 eth0: RTL8168c/8111c at 0xffffc90001870000, 00:e0:4c:80:66:57, XID 1c4000c0 IRQ 73
Jan  9 09:09:00 elmo kernel: [125549.128755] r8169 0000:03:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 09:09:00 elmo kernel: [125549.145664] r8169 0000:06:00.0: can't disable ASPM; OS doesn't have ASPM control
Jan  9 09:09:00 elmo kernel: [125549.145934] r8169 0000:06:00.0: irq 74 for MSI/MSI-X
Jan  9 09:09:00 elmo kernel: [125549.146934] r8169 0000:03:00.0 eth0: link down
Jan  9 09:09:00 elmo kernel: [125549.147189] r8169 0000:06:00.0 eth1: RTL8168c/8111c at 0xffffc9000187e000, 00:e0:4c:80:70:08, XID 1c4000c0 IRQ 74
Jan  9 09:09:00 elmo kernel: [125549.147193] r8169 0000:06:00.0 eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Jan  9 09:09:00 elmo kernel: [125549.147234] r8169 0000:03:00.0 eth0: link down
Jan  9 09:09:03 elmo kernel: [125552.943570] r8169 0000:03:00.0 eth0: link up
Jan  9 09:09:28 elmo kernel: [125577.579875] r8169 0000:03:00.0 eth0: link up
Jan  9 09:10:34 elmo kernel: [125643.518729] r8169 0000:03:00.0 eth0: link up
Jan  9 09:11:04 elmo kernel: [125673.505548] r8169 0000:03:00.0 eth0: link up
Jan  9 09:11:52 elmo kernel: [125721.462613] r8169 0000:03:00.0 eth0: link up
Jan  9 09:12:22 elmo kernel: [125751.445129] r8169 0000:03:00.0 eth0: link up
Jan  9 09:13:31 elmo kernel: [125820.588517] r8169 0000:03:00.0 eth0: link down
Jan  9 09:13:31 elmo kernel: [125820.588524] r8169 0000:03:00.0 eth0: link down
Jan  9 09:13:34 elmo kernel: [125823.765570] r8169 0000:03:00.0 eth0: link up
Jan  9 09:13:59 elmo kernel: [125848.409967] r8169 0000:03:00.0 eth0: link up
Jan  9 10:56:59 elmo kernel: [132023.485940] r8169 0000:03:00.0 eth0: link down
Jan  9 11:02:14 elmo kernel: [132338.259437] r8169 0000:03:00.0 eth0: link up
Jan  9 11:02:15 elmo kernel: [132338.888600] r8169 0000:03:00.0 eth0: link down
Jan  9 11:02:17 elmo kernel: [132340.899557] r8169 0000:03:00.0 eth0: link up
Jan  9 12:21:59 elmo kernel: [137119.706747] r8169 0000:03:00.0 eth0: link up
Jan  9 13:46:58 elmo kernel: [142215.007812] r8169 0000:03:00.0 eth0: link down
Jan  9 13:51:11 elmo kernel: [142467.021851] r8169 0000:03:00.0 eth0: link up
Jan  9 13:51:12 elmo kernel: [142468.036445] r8169 0000:03:00.0 eth0: link down
Jan  9 13:51:13 elmo kernel: [142469.683089] r8169 0000:03:00.0 eth0: link up
Jan  9 14:22:01 elmo kernel: [144316.058860] r8169 0000:03:00.0 eth0: link up
Jan 10 00:15:01 elmo kernel: [179868.506724] r8169 0000:03:00.0 eth0: link up
Jan 10 01:34:07 elmo kernel: [184610.809173] r8169 0000:03:00.0 eth0: link up
Jan 10 06:27:19 elmo kernel: [202189.245589] r8169 0000:03:00.0 eth0: link up
Jan 10 10:25:17 elmo kernel: [216458.170910] r8169 0000:03:00.0 eth0: link up
Jan 10 10:50:23 elmo kernel: [217963.001075] r8169 0000:03:00.0 eth0: link up
Jan 10 11:04:29 elmo kernel: [218808.352269] r8169 0000:03:00.0 eth0: link up
Jan 10 11:27:35 elmo kernel: [220193.304666] r8169 0000:03:00.0 eth0: link up
Jan 10 11:50:23 elmo kernel: [221560.241410] r8169 0000:03:00.0 eth0: link up
Jan 10 12:05:59 elmo kernel: [222495.539781] r8169 0000:03:00.0 eth0: link up
Jan 10 12:29:41 elmo kernel: [223916.436973] r8169 0000:03:00.0 eth0: link up
Jan 10 12:51:23 elmo kernel: [225217.437479] r8169 0000:03:00.0 eth0: link up
Jan 10 13:04:53 elmo kernel: [226026.817632] r8169 0000:03:00.0 eth0: link up
Jan 10 13:28:47 elmo kernel: [227459.718466] r8169 0000:03:00.0 eth0: link up
Jan 10 13:51:35 elmo kernel: [228826.681757] r8169 0000:03:00.0 eth0: link up
Jan 10 14:03:41 elmo kernel: [229552.123700] r8169 0000:03:00.0 eth0: link up
Jan 10 14:26:23 elmo kernel: [230913.072252] r8169 0000:03:00.0 eth0: link up
Jan 10 14:47:11 elmo kernel: [232160.105546] r8169 0000:03:00.0 eth0: link up
Jan 10 15:12:11 elmo kernel: [233658.974021] r8169 0000:03:00.0 eth0: link up
Jan 10 15:29:29 elmo kernel: [234696.177510] r8169 0000:03:00.0 eth0: link up
Jan 10 15:50:23 elmo kernel: [235949.197834] r8169 0000:03:00.0 eth0: link up
Jan 10 16:13:17 elmo kernel: [237322.147870] r8169 0000:03:00.0 eth0: link up
Jan 10 16:34:17 elmo kernel: [238581.179914] r8169 0000:03:00.0 eth0: link up
Jan 10 16:59:23 elmo kernel: [240086.040262] r8169 0000:03:00.0 eth0: link up
Jan 10 17:14:59 elmo kernel: [241021.338493] r8169 0000:03:00.0 eth0: link up
Jan 10 17:36:29 elmo kernel: [242310.318221] r8169 0000:03:00.0 eth0: link up
Jan 10 18:00:29 elmo kernel: [243749.209619] r8169 0000:03:00.0 eth0: link up
Jan 10 18:24:17 elmo kernel: [245176.117274] r8169 0000:03:00.0 eth0: link up
Jan 10 18:47:11 elmo kernel: [246549.108048] r8169 0000:03:00.0 eth0: link up
Jan 10 19:02:35 elmo kernel: [247472.355174] r8169 0000:03:00.0 eth0: link up
Jan 10 19:26:47 elmo kernel: [248923.303384] r8169 0000:03:00.0 eth0: link up
Jan 10 19:50:47 elmo kernel: [250362.144802] r8169 0000:03:00.0 eth0: link up
Jan 10 20:13:29 elmo kernel: [251723.101783] r8169 0000:03:00.0 eth0: link up
Jan 10 20:35:29 elmo kernel: [253042.081251] r8169 0000:03:00.0 eth0: link up
Jan 10 20:59:29 elmo kernel: [254480.981747] r8169 0000:03:00.0 eth0: link up
Jan 10 21:22:17 elmo kernel: [255847.927367] r8169 0000:03:00.0 eth0: link up
Jan 10 21:46:11 elmo kernel: [257280.835154] r8169 0000:03:00.0 eth0: link up
Jan 10 22:10:35 elmo kernel: [258743.709869] r8169 0000:03:00.0 eth0: link up
Jan 10 22:25:23 elmo kernel: [259631.016371] r8169 0000:03:00.0 eth0: link up
Jan 10 22:49:47 elmo kernel: [261093.912822] r8169 0000:03:00.0 eth0: link up
Jan 10 23:14:29 elmo kernel: [262574.775599] r8169 0000:03:00.0 eth0: link up
Jan 10 23:41:05 elmo kernel: [264169.532821] r8169 0000:03:00.0 eth0: link up
Jan 11 00:20:29 elmo kernel: [266531.713878] r8169 0000:03:00.0 eth0: link up
Jan 11 01:08:29 elmo kernel: [269409.500032] r8169 0000:03:00.0 eth0: link up
Jan 11 01:22:35 elmo kernel: [270254.861202] r8169 0000:03:00.0 eth0: link up
Jan 11 01:45:53 elmo kernel: [271651.779561] r8169 0000:03:00.0 eth0: link up
Jan 11 02:09:29 elmo kernel: [273066.706131] r8169 0000:03:00.0 eth0: link up
Jan 11 02:25:11 elmo kernel: [274008.016185] r8169 0000:03:00.0 eth0: link up
Jan 11 02:48:53 elmo kernel: [275428.884591] r8169 0000:03:00.0 eth0: link up
Jan 11 03:14:05 elmo kernel: [276939.735485] r8169 0000:03:00.0 eth0: link up
Jan 11 03:55:29 elmo kernel: [279421.824429] r8169 0000:03:00.0 eth0: link up
Jan 11 04:42:29 elmo kernel: [282239.665715] r8169 0000:03:00.0 eth0: link up
Jan 11 05:26:05 elmo kernel: [284853.658781] r8169 0000:03:00.0 eth0: link up
Jan 11 06:14:05 elmo kernel: [287731.454199] r8169 0000:03:00.0 eth0: link up
Jan 11 06:25:11 elmo kernel: [288396.950192] r8169 0000:03:00.0 eth0: link up
Jan 11 06:41:23 elmo kernel: [289368.205492] r8169 0000:03:00.0 eth0: link up
Jan 11 07:05:29 elmo kernel: [290813.090764] r8169 0000:03:00.0 eth0: link up
Jan 11 07:28:11 elmo kernel: [292174.044720] r8169 0000:03:00.0 eth0: link up
Jan 11 07:52:23 elmo kernel: [293624.947008] r8169 0000:03:00.0 eth0: link up
Jan 11 08:16:17 elmo kernel: [295057.821023] r8169 0000:03:00.0 eth0: link up
Jan 11 08:30:35 elmo kernel: [295915.174546] r8169 0000:03:00.0 eth0: link up
Jan 11 08:56:41 elmo kernel: [297479.953856] r8169 0000:03:00.0 eth0: link up
Jan 11 09:20:41 elmo kernel: [298918.875097] r8169 0000:03:00.0 eth0: link up
Jan 11 09:42:29 elmo kernel: [300225.856036] r8169 0000:03:00.0 eth0: link up
Jan 11 10:05:17 elmo kernel: [301592.816385] r8169 0000:03:00.0 eth0: link up
Jan 11 10:22:47 elmo kernel: [302642.021483] r8169 0000:03:00.0 eth0: link up
Jan 11 10:46:41 elmo kernel: [304074.915787] r8169 0000:03:00.0 eth0: link up
Jan 11 11:12:47 elmo kernel: [305639.727570] r8169 0000:03:00.0 eth0: link up
Jan 11 11:43:17 elmo kernel: [307468.308263] r8169 0000:03:00.0 eth0: link up
Jan 11 11:56:53 elmo kernel: [308283.696450] r8169 0000:03:00.0 eth0: link up
Jan 11 12:19:47 elmo kernel: [309656.641788] r8169 0000:03:00.0 eth0: link up
Jan 11 12:43:05 elmo kernel: [311053.560314] r8169 0000:03:00.0 eth0: link up
Jan 11 13:07:47 elmo kernel: [312534.418463] r8169 0000:03:00.0 eth0: link up
Jan 11 13:30:41 elmo kernel: [313907.365171] r8169 0000:03:00.0 eth0: link up
Jan 11 13:54:17 elmo kernel: [315322.276762] r8169 0000:03:00.0 eth0: link up
Jan 11 14:18:47 elmo kernel: [316791.163514] r8169 0000:03:00.0 eth0: link up
Jan 11 14:42:29 elmo kernel: [318212.066921] r8169 0000:03:00.0 eth0: link up
Jan 11 15:07:47 elmo kernel: [319728.890740] r8169 0000:03:00.0 eth0: link up
Jan 11 15:22:47 elmo kernel: [320628.199976] r8169 0000:03:00.0 eth0: link up
Jan 11 15:46:41 elmo kernel: [322061.101203] r8169 0000:03:00.0 eth0: link up
Jan 11 16:09:59 elmo kernel: [323458.047578] r8169 0000:03:00.0 eth0: link up
Jan 11 16:32:29 elmo kernel: [324807.000015] r8169 0000:03:00.0 eth0: link up
Jan 11 16:56:17 elmo kernel: [326233.897558] r8169 0000:03:00.0 eth0: link up
Jan 11 17:19:23 elmo kernel: [327618.832116] r8169 0000:03:00.0 eth0: link up
Jan 11 17:42:17 elmo kernel: [328991.781805] r8169 0000:03:00.0 eth0: link up
Jan 11 17:58:29 elmo kernel: [329963.040468] r8169 0000:03:00.0 eth0: link up
Jan 11 18:19:29 elmo kernel: [331222.061017] r8169 0000:03:00.0 eth0: link up
Jan 11 18:43:17 elmo kernel: [332648.954572] r8169 0000:03:00.0 eth0: link up
Jan 11 19:12:53 elmo kernel: [334423.600928] r8169 0000:03:00.0 eth0: link up
Jan 11 19:54:23 elmo kernel: [336911.694736] r8169 0000:03:00.0 eth0: link up
Jan 11 20:08:29 elmo kernel: [337757.063044] r8169 0000:03:00.0 eth0: link up
Jan 11 20:32:17 elmo kernel: [339183.947065] r8169 0000:03:00.0 eth0: link up
Jan 11 20:56:41 elmo kernel: [340646.830012] r8169 0000:03:00.0 eth0: link up
Jan 11 21:12:35 elmo kernel: [341600.106319] r8169 0000:03:00.0 eth0: link up
Jan 11 21:34:59 elmo kernel: [342943.072953] r8169 0000:03:00.0 eth0: link up
Jan 11 21:58:23 elmo kernel: [344346.010377] r8169 0000:03:00.0 eth0: link up
Jan 11 22:27:29 elmo kernel: [346090.650653] r8169 0000:03:00.0 eth0: link up
Jan 11 22:39:29 elmo kernel: [346810.097681] r8169 0000:03:00.0 eth0: link up
Jan 11 23:03:05 elmo kernel: [348225.015098] r8169 0000:03:00.0 eth0: link up
Jan 11 23:26:29 elmo kernel: [349627.946117] r8169 0000:03:00.0 eth0: link up
Jan 11 23:41:41 elmo kernel: [350539.240694] r8169 0000:03:00.0 eth0: link up
Jan 12 00:05:41 elmo kernel: [351978.133377] r8169 0000:03:00.0 eth0: link up
Jan 12 00:28:05 elmo kernel: [353321.087554] r8169 0000:03:00.0 eth0: link up
Jan 12 01:12:17 elmo kernel: [355971.080348] r8169 0000:03:00.0 eth0: link up
Jan 12 01:58:17 elmo kernel: [358728.956382] r8169 0000:03:00.0 eth0: link up
Jan 12 02:44:11 elmo kernel: [361480.834141] r8169 0000:03:00.0 eth0: link up
Jan 12 03:33:35 elmo kernel: [364442.572951] r8169 0000:03:00.0 eth0: link up
Jan 12 03:44:29 elmo kernel: [365096.063835] r8169 0000:03:00.0 eth0: link up
Jan 12 04:10:41 elmo kernel: [366666.862665] r8169 0000:03:00.0 eth0: link up
Jan 12 04:35:17 elmo kernel: [368141.719614] r8169 0000:03:00.0 eth0: link up
Jan 12 04:50:59 elmo kernel: [369083.003813] r8169 0000:03:00.0 eth0: link up
Jan 12 05:14:53 elmo kernel: [370515.900323] r8169 0000:03:00.0 eth0: link up
Jan 12 05:37:53 elmo kernel: [371894.857820] r8169 0000:03:00.0 eth0: link up
Jan 12 05:53:05 elmo kernel: [372806.157333] r8169 0000:03:00.0 eth0: link up
Jan 12 06:15:59 elmo kernel: [374179.086690] r8169 0000:03:00.0 eth0: link up

Re: r8169 won't transmit with 3.12

[Francois Romieu]

Craig Small <csmall@enc.com.au> :
> On Wed, Jan 22, 2014 at 12:36:30AM +0100, Francois Romieu wrote:
> > You may check that the onboard nic device does not even work when the
> > extra PCI-e card aren't plugged.
> It definitely doesn't. I've tried with only the onboard device
> and no other NIC device (r8169 or not) installed and its the same
> problem.

Should I understand that the LOM fails on Linux with a naked motherboard ?

> > A complete dmesg including the XID lines that the r8169 driver prints
> > would be welcome.
> See attached text file. I'm not sure why I get so many interface up
> messages.

Please check if runtime resume is disabled (/sys/bus/pci/devices/.../power/control
should be 'on'). If so and you do not see many netdev watchdog messages either,
these could be real link status change events.

> This is for the two NIC cards. I can pull them out and go back to the
> onboard one if you like.

Please do (and send a complete dmesg).

Your previous posting suggests that the LOM board is a 8168b but I haven't
seen its XID.

It could help to check the add-on 8168c in a different computer whose
motherboard does not include any networking chipset from Realtek (nor
any bios that could confuse different revisions of those).

Please don't switch between the r8168 and the r8169 modules at runtime.
I saw it in your dmesg and I won't claim it's supported.

I'll be out for work during two days.

Thanks.

-- 
Ueimor

Re: r8169 won't transmit with 3.12

[Craig Small]

[-- Attachment #1: Type: text/plain, Size: 1924 bytes --]

On Thu, Jan 23, 2014 at 12:31:35AM +0100, Francois Romieu wrote:
> Should I understand that the LOM fails on Linux with a naked motherboard ?
Not sure what you mean by LOM. There is no Lights Out Module. I have
now removed the two ethernet cards and enabled the motherboard NIC.
I'll leave it like this. There is one ethernet card that uses a 
8139too module.
The relevant interface is:
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
	Subsystem: Gigabyte Technology Co., Ltd Motherboard
	Flags: bus master, fast devsel, latency 0, IRQ 72
	I/O ports at d000 [size=256]
	Memory at fdd00000 (64-bit, non-prefetchable) [size=4K]
	Memory at d2100000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Capabilities: [70] Express Endpoint, MSI 01
	Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
	Capabilities: [d0] Vital Product Data
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 01-00-00-00-68-4c-e0-00
	Kernel driver in use: r8169

eth5 is the working r8139
eth6 is the r8169 that we're interested in.

> Please check if runtime resume is disabled (/sys/bus/pci/devices/.../power/control
$ cat /sys/bus/pci/devices/0000\:03\:00.0/power/control 
on

> Please don't switch between the r8168 and the r8169 modules at runtime.
> I saw it in your dmesg and I won't claim it's supported.
That's fine. I was doing it to see if it would work. I'll stay with the r8169
for now. I got a watchdog notice now, not sure if that is better or worse.

 - Craig

-- 
Craig Small (@smallsees)   http://enc.com.au/       csmall at : enc.com.au
Debian GNU/Linux           http://www.debian.org/   csmall at : debian.org
GPG fingerprint:        5D2F B320 B825 D939 04D2  0519 3938 F96B DF50 FEA5

[-- Attachment #2: r8169dmesg2.txt --]
[-- Type: text/plain, Size: 60668 bytes --]

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.12-1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-10) ) #1 SMP Debian 3.12.6-2 (2013-12-29)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.12-1-amd64 root=UUID=a273d5f8-984b-4ce4-87dd-d6885f488b80 ro quiet
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000be866fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000be867000-0x00000000bea3efff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000bea3f000-0x00000000bee33fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bee34000-0x00000000bf15efff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000bf15f000-0x00000000bf15ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bf160000-0x00000000bf365fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bf366000-0x00000000bf7fffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec20000-0x00000000fec20fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed61000-0x00000000fed70fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fef00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100001000-0x000000043effffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: Gigabyte Technology Co., Ltd. To be filled by O.E.M./970A-D3P, BIOS F3 05/24/2013
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x43f000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF write-through
[    0.000000]   C0000-CEFFF write-protect
[    0.000000]   CF000-EBFFF uncachable
[    0.000000]   EC000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000BF800000 mask FFFFFF800000 uncachable
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 000000043f000000 aka 17392M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: update [mem 0xbf800000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xbf800 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fd820-0x000fd82f] mapped at [ffff8800000fd820]
[    0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01a91000, 0x01a91fff] PGTABLE
[    0.000000] BRK [0x01a92000, 0x01a92fff] PGTABLE
[    0.000000] BRK [0x01a93000, 0x01a93fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x43ee00000-0x43effffff]
[    0.000000]  [mem 0x43ee00000-0x43effffff] page 2M
[    0.000000] BRK [0x01a94000, 0x01a94fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x43c000000-0x43edfffff]
[    0.000000]  [mem 0x43c000000-0x43edfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x400000000-0x43bffffff]
[    0.000000]  [mem 0x400000000-0x43bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0xbe866fff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xbe7fffff] page 2M
[    0.000000]  [mem 0xbe800000-0xbe866fff] page 4k
[    0.000000] init_memory_mapping: [mem 0xbf15f000-0xbf15ffff]
[    0.000000]  [mem 0xbf15f000-0xbf15ffff] page 4k
[    0.000000] BRK [0x01a95000, 0x01a95fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xbf366000-0xbf7fffff]
[    0.000000]  [mem 0xbf366000-0xbf3fffff] page 4k
[    0.000000]  [mem 0xbf400000-0xbf7fffff] page 2M
[    0.000000] BRK [0x01a96000, 0x01a96fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x100001000-0x3ffffffff]
[    0.000000]  [mem 0x100001000-0x1001fffff] page 4k
[    0.000000]  [mem 0x100200000-0x13fffffff] page 2M
[    0.000000]  [mem 0x140000000-0x3ffffffff] page 1G
[    0.000000] RAMDISK: [mem 0x363bc000-0x371d5fff]
[    0.000000] ACPI: RSDP 00000000000f0490 00024 (v02 ALASKA)
[    0.000000] ACPI: XSDT 00000000bee19068 00054 (v01 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI: FACP 00000000bee1eba0 000F4 (v04 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20130725/tbfadt-603)
[    0.000000] ACPI: DSDT 00000000bee19158 05A42 (v02 ALASKA    A M I 00000000 INTL 20051117)
[    0.000000] ACPI: FACS 00000000bee2ef80 00040
[    0.000000] ACPI: APIC 00000000bee1ec98 0008E (v03 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI: FPDT 00000000bee1ed28 00044 (v01 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI: MCFG 00000000bee1ed70 0003C (v01 ALASKA    A M I 01072009 MSFT 00010013)
[    0.000000] ACPI: HPET 00000000bee1edb0 00038 (v01 ALASKA    A M I 01072009 AMI  00000005)
[    0.000000] ACPI: SSDT 00000000bee1ede8 01158 (v01 AMD    POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000043effffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x43effffff]
[    0.000000]   NODE_DATA [mem 0x43eff8000-0x43effbfff]
[    0.000000]  [ffffea0000000000-ffffea000edfffff] PMD -> [ffff88042e600000-ffff88043c5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x43effffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009dfff]
[    0.000000]   node   0: [mem 0x00100000-0xbe866fff]
[    0.000000]   node   0: [mem 0xbf15f000-0xbf15ffff]
[    0.000000]   node   0: [mem 0xbf366000-0xbf7fffff]
[    0.000000]   node   0: [mem 0x100001000-0x43effffff]
[    0.000000] On node 0 totalpages: 4185246
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3997 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10630 pages used for memmap
[    0.000000]   DMA32 zone: 777474 pages, LIFO batch:31
[    0.000000]   Normal zone: 46536 pages used for memmap
[    0.000000]   Normal zone: 3403775 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x11] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x13] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x15] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 7, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec20000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 8, version 33, address 0xfec20000, GSI 24-55
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000
[    0.000000] smpboot: Allowing 6 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 72
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbe867000-0xbea3efff]
[    0.000000] PM: Registered nosave memory: [mem 0xbea3f000-0xbee33fff]
[    0.000000] PM: Registered nosave memory: [mem 0xbee34000-0xbf15efff]
[    0.000000] PM: Registered nosave memory: [mem 0xbf160000-0xbf365fff]
[    0.000000] PM: Registered nosave memory: [mem 0xbf800000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfec0ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfec1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec20000-0xfec20fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec21000-0xfecfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed60fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed61000-0xfed70fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed71000-0xfed7ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xfeefffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfef00000-0xffffffff]
[    0.000000] PM: Registered nosave memory: [mem 0x100000000-0x100000fff]
[    0.000000] e820: [mem 0xbf800000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:6 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff88043ec00000 s85888 r8192 d20608 u262144
[    0.000000] pcpu-alloc: s85888 r8192 d20608 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 - - 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 4128003
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.12-1-amd64 root=UUID=a273d5f8-984b-4ce4-87dd-d6885f488b80 ro quiet
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ f8000000 size 64 MB
[    0.000000] Memory: 16419228K/16740984K available (4726K kernel code, 679K rwdata, 1596K rodata, 972K init, 944K bss, 321756K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=6.
[    0.000000] NR_IRQS:33024 nr_irqs:1272 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.004000] tsc: Detected 3516.208 MHz processor
[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 7032.41 BogoMIPS (lpj=14064832)
[    0.000005] pid_max: default: 32768 minimum: 301
[    0.000028] Security Framework initialized
[    0.000032] AppArmor: AppArmor disabled by boot time parameter
[    0.000033] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.000936] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.005763] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.007979] Mount-cache hash table entries: 256
[    0.008135] Initializing cgroup subsys memory
[    0.008150] Initializing cgroup subsys devices
[    0.008151] Initializing cgroup subsys freezer
[    0.008153] Initializing cgroup subsys net_cls
[    0.008154] Initializing cgroup subsys blkio
[    0.008156] Initializing cgroup subsys perf_event
[    0.008175] tseg: 00bf800000
[    0.008176] CPU: Physical Processor ID: 0
[    0.008177] CPU: Processor Core ID: 0
[    0.008179] mce: CPU supports 7 MCE banks
[    0.008185] LVT offset 1 assigned for vector 0xf9
[    0.008190] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[    0.008190] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512
[    0.008190] tlb_flushall_shift: 5
[    0.008255] Freeing SMP alternatives memory: 20K (ffffffff8199e000 - ffffffff819a3000)
[    0.008909] ACPI: Core revision 20130725
[    0.010692] ACPI: All ACPI Tables successfully acquired
[    0.011266] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.050920] smpboot: CPU0: AMD FX(tm)-6300 Six-Core Processor (fam: 15, model: 02, stepping: 00)
[    0.155558] Performance Events: Fam15h core perfctr, AMD PMU driver.
[    0.155562] ... version:                0
[    0.155563] ... bit width:              48
[    0.155564] ... generic registers:      6
[    0.155565] ... value mask:             0000ffffffffffff
[    0.155566] ... max period:             00007fffffffffff
[    0.155567] ... fixed-purpose events:   0
[    0.155568] ... event mask:             000000000000003f
[    0.155769] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.155852] smpboot: Booting Node   0, Processors  #   1 #   2 #   3 #   4 #   5 OK
[    0.222129] Brought up 6 CPUs
[    0.222132] smpboot: Total of 6 processors activated (42194.49 BogoMIPS)
[    0.229791] devtmpfs: initialized
[    0.233032] PM: Registering ACPI NVS region [mem 0xbea3f000-0xbee33fff] (4149248 bytes)
[    0.233103] PM: Registering ACPI NVS region [mem 0xbf160000-0xbf365fff] (2121728 bytes)
[    0.233298] NET: Registered protocol family 16
[    0.233372] cpuidle: using governor ladder
[    0.233373] cpuidle: using governor menu
[    0.233406] ACPI: bus type PCI registered
[    0.233408] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.233450] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.233452] PCI: not using MMCONFIG
[    0.233453] PCI: Using configuration type 1 for base access
[    0.233454] PCI: Using configuration type 1 for extended access
[    0.233712] mtrr: your CPUs had inconsistent variable MTRR settings
[    0.233713] mtrr: probably your BIOS does not setup all CPUs.
[    0.233713] mtrr: corrected configuration.
[    0.234147] bio: create slab <bio-0> at 0
[    0.234289] ACPI: Added _OSI(Module Device)
[    0.234290] ACPI: Added _OSI(Processor Device)
[    0.234291] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.234292] ACPI: Added _OSI(Processor Aggregator Device)
[    0.234779] ACPI: EC: Look up EC in DSDT
[    0.235592] ACPI: Executed 3 blocks of module-level executable AML code
[    0.243903] ACPI: Interpreter enabled
[    0.243910] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130725/hwxface-571)
[    0.243914] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
[    0.243925] ACPI: (supports S0 S3 S4 S5)
[    0.243926] ACPI: Using IOAPIC for interrupt routing
[    0.244039] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.244072] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.256483] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.256559] ACPI: No dock devices found.
[    0.269107] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.269112] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.269113] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.269344] ACPI: \_SB_.PCI0.AMDN: can't evaluate _ADR (0x5)
[    0.269412] ACPI: \_SB_.PCI0.UMEM: can't evaluate _ADR (0x5)
[    0.269460] ACPI: \_SB_.PCI0.ITPM: can't evaluate _ADR (0x5)
[    0.269462] PCI host bridge to bus 0000:00
[    0.269464] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.269465] pci_bus 0000:00: root bus resource [io  0x0000-0x03af]
[    0.269467] pci_bus 0000:00: root bus resource [io  0x03e0-0x0cf7]
[    0.269468] pci_bus 0000:00: root bus resource [io  0x03b0-0x03df]
[    0.269470] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.269471] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.269472] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.269474] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
[    0.269483] pci 0000:00:00.0: [1002:5a14] type 00 class 0x060000
[    0.269610] pci 0000:00:02.0: [1002:5a16] type 01 class 0x060400
[    0.269640] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.269680] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.269705] pci 0000:00:04.0: [1002:5a18] type 01 class 0x060400
[    0.269733] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[    0.269779] pci 0000:00:04.0: System wakeup disabled by ACPI
[    0.269806] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400
[    0.269834] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
[    0.269873] pci 0000:00:09.0: System wakeup disabled by ACPI
[    0.269896] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400
[    0.269924] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold
[    0.269964] pci 0000:00:0a.0: System wakeup disabled by ACPI
[    0.269995] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601
[    0.270010] pci 0000:00:11.0: reg 0x10: [io  0xf040-0xf047]
[    0.270017] pci 0000:00:11.0: reg 0x14: [io  0xf030-0xf033]
[    0.270024] pci 0000:00:11.0: reg 0x18: [io  0xf020-0xf027]
[    0.270031] pci 0000:00:11.0: reg 0x1c: [io  0xf010-0xf013]
[    0.270038] pci 0000:00:11.0: reg 0x20: [io  0xf000-0xf00f]
[    0.270045] pci 0000:00:11.0: reg 0x24: [mem 0xfd10b000-0xfd10b3ff]
[    0.270135] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
[    0.270145] pci 0000:00:12.0: reg 0x10: [mem 0xfd10a000-0xfd10afff]
[    0.270219] pci 0000:00:12.0: System wakeup disabled by ACPI
[    0.270246] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
[    0.270260] pci 0000:00:12.2: reg 0x10: [mem 0xfd109000-0xfd1090ff]
[    0.270319] pci 0000:00:12.2: supports D1 D2
[    0.270321] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.270361] pci 0000:00:12.2: System wakeup disabled by ACPI
[    0.270386] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
[    0.270396] pci 0000:00:13.0: reg 0x10: [mem 0xfd108000-0xfd108fff]
[    0.270470] pci 0000:00:13.0: System wakeup disabled by ACPI
[    0.270497] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
[    0.270510] pci 0000:00:13.2: reg 0x10: [mem 0xfd107000-0xfd1070ff]
[    0.270570] pci 0000:00:13.2: supports D1 D2
[    0.270571] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[    0.270612] pci 0000:00:13.2: System wakeup disabled by ACPI
[    0.270638] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[    0.270737] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[    0.270753] pci 0000:00:14.2: reg 0x10: [mem 0xfd100000-0xfd103fff 64bit]
[    0.270828] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.270867] pci 0000:00:14.2: System wakeup disabled by ACPI
[    0.270888] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
[    0.270987] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[    0.271046] pci 0000:00:14.4: System wakeup disabled by ACPI
[    0.271067] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
[    0.271077] pci 0000:00:14.5: reg 0x10: [mem 0xfd106000-0xfd106fff]
[    0.271152] pci 0000:00:14.5: System wakeup disabled by ACPI
[    0.271176] pci 0000:00:16.0: [1002:4397] type 00 class 0x0c0310
[    0.271186] pci 0000:00:16.0: reg 0x10: [mem 0xfd105000-0xfd105fff]
[    0.271261] pci 0000:00:16.0: System wakeup disabled by ACPI
[    0.271288] pci 0000:00:16.2: [1002:4396] type 00 class 0x0c0320
[    0.271302] pci 0000:00:16.2: reg 0x10: [mem 0xfd104000-0xfd1040ff]
[    0.271362] pci 0000:00:16.2: supports D1 D2
[    0.271363] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[    0.271403] pci 0000:00:16.2: System wakeup disabled by ACPI
[    0.271428] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000
[    0.271487] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000
[    0.271541] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000
[    0.271596] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000
[    0.271654] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000
[    0.271709] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000
[    0.271806] pci 0000:01:00.0: [10de:0a65] type 00 class 0x030000
[    0.271814] pci 0000:01:00.0: reg 0x10: [mem 0xfc000000-0xfcffffff]
[    0.271823] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.271831] pci 0000:01:00.0: reg 0x1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[    0.271837] pci 0000:01:00.0: reg 0x24: [io  0xe000-0xe07f]
[    0.271843] pci 0000:01:00.0: reg 0x30: [mem 0xfd000000-0xfd07ffff pref]
[    0.271910] pci 0000:01:00.1: [10de:0be3] type 00 class 0x040300
[    0.271918] pci 0000:01:00.1: reg 0x10: [mem 0xfd080000-0xfd083fff]
[    0.281011] pci 0000:00:02.0: PCI bridge to [bus 01]
[    0.281015] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.281017] pci 0000:00:02.0:   bridge window [mem 0xfc000000-0xfd0fffff]
[    0.281020] pci 0000:00:02.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.281060] pci 0000:02:00.0: [1106:3483] type 00 class 0x0c0330
[    0.281072] pci 0000:02:00.0: reg 0x10: [mem 0xfde00000-0xfde00fff 64bit]
[    0.281122] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.289027] pci 0000:00:04.0: PCI bridge to [bus 02]
[    0.289031] pci 0000:00:04.0:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.289086] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000
[    0.289099] pci 0000:03:00.0: reg 0x10: [io  0xd000-0xd0ff]
[    0.289117] pci 0000:03:00.0: reg 0x18: [mem 0xfdd00000-0xfdd00fff 64bit]
[    0.289129] pci 0000:03:00.0: reg 0x20: [mem 0xd2100000-0xd2103fff 64bit pref]
[    0.289179] pci 0000:03:00.0: supports D1 D2
[    0.289180] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.289206] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.296996] pci 0000:00:09.0: PCI bridge to [bus 03]
[    0.296999] pci 0000:00:09.0:   bridge window [io  0xd000-0xdfff]
[    0.297002] pci 0000:00:09.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.297005] pci 0000:00:09.0:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.297051] pci 0000:04:00.0: [1131:7164] type 00 class 0x048000
[    0.297070] pci 0000:04:00.0: reg 0x10: [mem 0xfd800000-0xfdbfffff 64bit]
[    0.297085] pci 0000:04:00.0: reg 0x18: [mem 0xfd400000-0xfd7fffff 64bit]
[    0.297161] pci 0000:04:00.0: supports D1 D2
[    0.297163] pci 0000:04:00.0: PME# supported from D0 D1 D2
[    0.304990] pci 0000:00:0a.0: PCI bridge to [bus 04]
[    0.304994] pci 0000:00:0a.0:   bridge window [mem 0xfd400000-0xfdbfffff]
[    0.305036] pci 0000:05:07.0: [1113:1211] type 00 class 0x020000
[    0.305053] pci 0000:05:07.0: reg 0x10: [io  0xc000-0xc0ff]
[    0.305063] pci 0000:05:07.0: reg 0x14: [mem 0xfdc10000-0xfdc100ff]
[    0.305105] pci 0000:05:07.0: reg 0x30: [mem 0xfdc00000-0xfdc0ffff pref]
[    0.305134] pci 0000:05:07.0: supports D1 D2
[    0.305135] pci 0000:05:07.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.305190] pci 0000:00:14.4: PCI bridge to [bus 05] (subtractive decode)
[    0.305193] pci 0000:00:14.4:   bridge window [io  0xc000-0xcfff]
[    0.305196] pci 0000:00:14.4:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.305199] pci 0000:00:14.4:   bridge window [io  0x0000-0x03af] (subtractive decode)
[    0.305200] pci 0000:00:14.4:   bridge window [io  0x03e0-0x0cf7] (subtractive decode)
[    0.305202] pci 0000:00:14.4:   bridge window [io  0x03b0-0x03df] (subtractive decode)
[    0.305203] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.305205] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.305206] pci 0000:00:14.4:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.305207] pci 0000:00:14.4:   bridge window [mem 0xc0000000-0xffffffff] (subtractive decode)
[    0.305522] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 11 14 15) *0
[    0.305573] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 11 14 15) *0
[    0.305625] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 11 14 15) *0
[    0.305676] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 10 11 14 15) *0
[    0.305717] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 10 11 14 15) *0
[    0.305750] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 10 11 14 15) *0
[    0.305782] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 10 11 14 15) *0
[    0.305815] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 10 11 14 15) *0
[    0.305881] ACPI: \_SB_.PCI0: notify handler is installed
[    0.305902] Found 1 acpi root devices
[    0.305975] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.305977] vgaarb: loaded
[    0.305978] vgaarb: bridge control possible 0000:01:00.0
[    0.306009] PCI: Using ACPI for IRQ routing
[    0.312306] PCI: pci_cache_line_size set to 64 bytes
[    0.312355] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[    0.312356] e820: reserve RAM buffer [mem 0xbe867000-0xbfffffff]
[    0.312357] e820: reserve RAM buffer [mem 0xbf160000-0xbfffffff]
[    0.312358] e820: reserve RAM buffer [mem 0xbf800000-0xbfffffff]
[    0.312359] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[    0.312432] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.312435] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.314477] Switched to clocksource hpet
[    0.315829] pnp: PnP ACPI init
[    0.315837] ACPI: bus type PNP registered
[    0.315898] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[    0.315901] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.316107] system 00:01: [io  0x040b] has been reserved
[    0.316109] system 00:01: [io  0x04d6] has been reserved
[    0.316111] system 00:01: [io  0x0c00-0x0c01] has been reserved
[    0.316112] system 00:01: [io  0x0c14] has been reserved
[    0.316114] system 00:01: [io  0x0c50-0x0c51] has been reserved
[    0.316115] system 00:01: [io  0x0c52] has been reserved
[    0.316117] system 00:01: [io  0x0c6c] has been reserved
[    0.316118] system 00:01: [io  0x0c6f] has been reserved
[    0.316120] system 00:01: [io  0x0cd0-0x0cd1] has been reserved
[    0.316121] system 00:01: [io  0x0cd2-0x0cd3] has been reserved
[    0.316123] system 00:01: [io  0x0cd4-0x0cd5] has been reserved
[    0.316124] system 00:01: [io  0x0cd6-0x0cd7] has been reserved
[    0.316125] system 00:01: [io  0x0cd8-0x0cdf] has been reserved
[    0.316127] system 00:01: [io  0x0800-0x089f] could not be reserved
[    0.316129] system 00:01: [io  0x0b20-0x0b3f] has been reserved
[    0.316130] system 00:01: [io  0x0900-0x090f] has been reserved
[    0.316132] system 00:01: [io  0x0910-0x091f] has been reserved
[    0.316134] system 00:01: [io  0xfe00-0xfefe] has been reserved
[    0.316136] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.316138] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.316139] system 00:01: [mem 0xfed80000-0xfed8ffff] has been reserved
[    0.316141] system 00:01: [mem 0xfed61000-0xfed70fff] has been reserved
[    0.316144] system 00:01: [mem 0xfec10000-0xfec10fff] has been reserved
[    0.316145] system 00:01: [mem 0xfed00000-0xfed00fff] has been reserved
[    0.316147] system 00:01: [mem 0xffc00000-0xffffffff] has been reserved
[    0.316149] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316264] system 00:02: [io  0x0220-0x0227] has been reserved
[    0.316266] system 00:02: [io  0x0228-0x0237] has been reserved
[    0.316267] system 00:02: [io  0x0a20-0x0a2f] has been reserved
[    0.316269] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316465] pnp 00:03: [dma 0 disabled]
[    0.316498] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.316507] pnp 00:04: [dma 4]
[    0.316520] pnp 00:04: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.316539] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.316557] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.316595] system 00:07: [io  0x04d0-0x04d1] has been reserved
[    0.316597] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316616] pnp 00:08: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.316642] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316742] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316830] system 00:0b: [mem 0xfec20000-0xfec200ff] could not be reserved
[    0.316832] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316936] pnp 00:0c: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.316938] pnp: PnP ACPI: found 13 devices
[    0.316939] ACPI: bus type PNP unregistered
[    0.323035] pci 0000:00:02.0: PCI bridge to [bus 01]
[    0.323038] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.323040] pci 0000:00:02.0:   bridge window [mem 0xfc000000-0xfd0fffff]
[    0.323043] pci 0000:00:02.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.323045] pci 0000:00:04.0: PCI bridge to [bus 02]
[    0.323048] pci 0000:00:04.0:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.323051] pci 0000:00:09.0: PCI bridge to [bus 03]
[    0.323053] pci 0000:00:09.0:   bridge window [io  0xd000-0xdfff]
[    0.323055] pci 0000:00:09.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.323057] pci 0000:00:09.0:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.323060] pci 0000:00:0a.0: PCI bridge to [bus 04]
[    0.323062] pci 0000:00:0a.0:   bridge window [mem 0xfd400000-0xfdbfffff]
[    0.323065] pci 0000:00:14.4: PCI bridge to [bus 05]
[    0.323067] pci 0000:00:14.4:   bridge window [io  0xc000-0xcfff]
[    0.323071] pci 0000:00:14.4:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.323077] pci_bus 0000:00: resource 4 [io  0x0000-0x03af]
[    0.323079] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7]
[    0.323080] pci_bus 0000:00: resource 6 [io  0x03b0-0x03df]
[    0.323081] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff]
[    0.323083] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[    0.323084] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
[    0.323086] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff]
[    0.323087] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.323088] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfd0fffff]
[    0.323090] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.323091] pci_bus 0000:02: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.323092] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    0.323094] pci_bus 0000:03: resource 1 [mem 0xfdd00000-0xfddfffff]
[    0.323095] pci_bus 0000:03: resource 2 [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.323096] pci_bus 0000:04: resource 1 [mem 0xfd400000-0xfdbfffff]
[    0.323098] pci_bus 0000:05: resource 0 [io  0xc000-0xcfff]
[    0.323099] pci_bus 0000:05: resource 1 [mem 0xfdc00000-0xfdcfffff]
[    0.323100] pci_bus 0000:05: resource 4 [io  0x0000-0x03af]
[    0.323102] pci_bus 0000:05: resource 5 [io  0x03e0-0x0cf7]
[    0.323103] pci_bus 0000:05: resource 6 [io  0x03b0-0x03df]
[    0.323104] pci_bus 0000:05: resource 7 [io  0x0d00-0xffff]
[    0.323105] pci_bus 0000:05: resource 8 [mem 0x000a0000-0x000bffff]
[    0.323107] pci_bus 0000:05: resource 9 [mem 0x000c0000-0x000dffff]
[    0.323108] pci_bus 0000:05: resource 10 [mem 0xc0000000-0xffffffff]
[    0.323188] NET: Registered protocol family 2
[    0.323466] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[    0.323874] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.324041] TCP: Hash tables configured (established 131072 bind 65536)
[    0.324065] TCP: reno registered
[    0.324083] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.324144] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.324292] NET: Registered protocol family 1
[    0.646409] pci 0000:01:00.0: Boot video device
[    0.646625] PCI: CLS 64 bytes, default 64
[    0.646654] Unpacking initramfs...
[    0.863943] Freeing initrd memory: 14440K (ffff8800363bc000 - ffff8800371d6000)
[    0.864306] PCI-DMA: Disabling AGP.
[    0.864374] PCI-DMA: aperture base @ f8000000 size 65536 KB
[    0.864375] init_memory_mapping: [mem 0xf8000000-0xfbffffff]
[    0.864377]  [mem 0xf8000000-0xfbffffff] page 2M
[    0.864384] PCI-DMA: using GART IOMMU.
[    0.864386] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    0.868899] perf: AMD NB counters detected
[    0.868922] LVT offset 0 assigned for vector 0x400
[    0.868941] perf: AMD IBS detected (0x000000ff)
[    0.868975] microcode: CPU0: patch_level=0x06000822
[    0.868982] microcode: CPU1: patch_level=0x06000822
[    0.868990] microcode: CPU2: patch_level=0x06000822
[    0.868997] microcode: CPU3: patch_level=0x06000822
[    0.869001] microcode: CPU4: patch_level=0x06000822
[    0.869006] microcode: CPU5: patch_level=0x06000822
[    0.869069] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.869301] audit: initializing netlink socket (disabled)
[    0.869315] type=2000 audit(1390461592.756:1): initialized
[    0.878684] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.879658] VFS: Disk quotas dquot_6.5.2
[    0.879681] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.879744] msgmni has been set to 32225
[    0.879999] alg: No test for stdrng (krng)
[    0.880023] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.880062] io scheduler noop registered
[    0.880064] io scheduler deadline registered
[    0.880086] io scheduler cfq registered (default)
[    0.880360] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.880371] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.880406] GHES: HEST is not enabled!
[    0.880444] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.900773] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.901061] Linux agpgart interface v0.103
[    0.901123] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.901470] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.901476] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.901588] mousedev: PS/2 mouse device common for all mice
[    0.901614] rtc_cmos 00:05: RTC can wake from S4
[    0.901704] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    0.901724] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.901733] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    0.901734] AMD IOMMUv2 functionality not available on this system
[    0.901795] TCP: cubic registered
[    0.901860] NET: Registered protocol family 10
[    0.902003] mip6: Mobile IPv6
[    0.902004] NET: Registered protocol family 17
[    0.902007] mpls_gso: MPLS GSO support
[    0.902382] registered taskstats version 1
[    0.903410] rtc_cmos 00:05: setting system clock to 2014-01-23 07:19:53 UTC (1390461593)
[    0.903443] PM: Hibernation image not present or could not be loaded.
[    0.904021] Freeing unused kernel memory: 972K (ffffffff818ab000 - ffffffff8199e000)
[    0.904023] Write protecting the kernel read-only data: 8192k
[    0.906309] Freeing unused kernel memory: 1408K (ffff8800014a0000 - ffff880001600000)
[    0.907026] Freeing unused kernel memory: 452K (ffff88000178f000 - ffff880001800000)
[    0.915094] systemd-udevd[78]: starting version 204
[    0.927238] ACPI: bus type USB registered
[    0.927265] usbcore: registered new interface driver usbfs
[    0.927275] usbcore: registered new interface driver hub
[    0.928722] SCSI subsystem initialized
[    0.932320] libata version 3.00 loaded.
[    0.932522] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.932535] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[    0.932541] pcieport 0000:00:09.0: driver skip pci_set_master, fix it!
[    0.932808] r8169 0000:03:00.0: irq 72 for MSI/MSI-X
[    0.932985] r8169 0000:03:00.0 eth0: RTL8168evl/8111evl at 0xffffc90001820000, 94:de:80:bf:e9:8b, XID 0c900800 IRQ 72
[    0.932988] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    0.933068] usbcore: registered new device driver usb
[    0.933167] ahci 0000:00:11.0: version 3.0
[    0.933343] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[    0.933346] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part 
[    0.933759] xhci_hcd 0000:02:00.0: xHCI Host Controller
[    0.933768] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
[    0.933857] xhci_hcd 0000:02:00.0: irq 73 for MSI/MSI-X
[    0.933914] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.934155] ehci-pci: EHCI PCI platform driver
[    0.934322] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.934492] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.934494] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.934496] usb usb1: Product: xHCI Host Controller
[    0.934498] usb usb1: Manufacturer: Linux 3.12-1-amd64 xhci_hcd
[    0.934500] usb usb1: SerialNumber: 0000:02:00.0
[    0.934570] ohci-pci: OHCI PCI platform driver
[    0.934648] hub 1-0:1.0: USB hub found
[    0.934657] hub 1-0:1.0: 1 port detected
[    0.934758] xhci_hcd 0000:02:00.0: xHCI Host Controller
[    0.934761] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[    0.934806] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    0.934808] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.934810] usb usb2: Product: xHCI Host Controller
[    0.934812] usb usb2: Manufacturer: Linux 3.12-1-amd64 xhci_hcd
[    0.934814] usb usb2: SerialNumber: 0000:02:00.0
[    0.934935] hub 2-0:1.0: USB hub found
[    0.934944] hub 2-0:1.0: 4 ports detected
[    0.935295] scsi0 : ahci
[    0.935596] scsi1 : ahci
[    0.935667] scsi2 : ahci
[    0.935744] scsi3 : ahci
[    0.935807] scsi4 : ahci
[    0.935897] scsi5 : ahci
[    0.935941] ata1: SATA max UDMA/133 abar m1024@0xfd10b000 port 0xfd10b100 irq 19
[    0.935944] ata2: SATA max UDMA/133 abar m1024@0xfd10b000 port 0xfd10b180 irq 19
[    0.935946] ata3: SATA max UDMA/133 abar m1024@0xfd10b000 port 0xfd10b200 irq 19
[    0.935949] ata4: SATA max UDMA/133 abar m1024@0xfd10b000 port 0xfd10b280 irq 19
[    0.935951] ata5: SATA max UDMA/133 abar m1024@0xfd10b000 port 0xfd10b300 irq 19
[    0.935954] ata6: SATA max UDMA/133 abar m1024@0xfd10b000 port 0xfd10b380 irq 19
[    0.936069] ehci-pci 0000:00:12.2: EHCI Host Controller
[    0.936076] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 3
[    0.936087] QUIRK: Enable AMD PLL fix
[    0.936089] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    0.936099] ehci-pci 0000:00:12.2: debug port 1
[    0.936131] ehci-pci 0000:00:12.2: irq 17, io mem 0xfd109000
[    0.940175] 8139too: 8139too Fast Ethernet driver 0.9.28
[    0.940761] 8139too 0000:05:07.0 eth1: RealTek RTL8139 at 0xffffc90011bcc000, 00:04:e2:12:1c:ea, IRQ 21
[    0.946006] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    0.946050] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    0.946052] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.946054] usb usb3: Product: EHCI Host Controller
[    0.946056] usb usb3: Manufacturer: Linux 3.12-1-amd64 ehci_hcd
[    0.946058] usb usb3: SerialNumber: 0000:00:12.2
[    0.946218] hub 3-0:1.0: USB hub found
[    0.946227] hub 3-0:1.0: 5 ports detected
[    0.946495] ehci-pci 0000:00:13.2: EHCI Host Controller
[    0.946507] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 4
[    0.946511] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    0.946521] ehci-pci 0000:00:13.2: debug port 1
[    0.946543] ehci-pci 0000:00:13.2: irq 17, io mem 0xfd107000
[    0.958033] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    0.958134] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    0.958137] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.958139] usb usb4: Product: EHCI Host Controller
[    0.958140] usb usb4: Manufacturer: Linux 3.12-1-amd64 ehci_hcd
[    0.958141] usb usb4: SerialNumber: 0000:00:13.2
[    0.958238] hub 4-0:1.0: USB hub found
[    0.958252] hub 4-0:1.0: 5 ports detected
[    0.958465] ehci-pci 0000:00:16.2: EHCI Host Controller
[    0.958469] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 5
[    0.958472] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    0.958480] ehci-pci 0000:00:16.2: debug port 1
[    0.958500] ehci-pci 0000:00:16.2: irq 17, io mem 0xfd104000
[    0.970058] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00
[    0.970137] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    0.970139] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.970141] usb usb5: Product: EHCI Host Controller
[    0.970142] usb usb5: Manufacturer: Linux 3.12-1-amd64 ehci_hcd
[    0.970143] usb usb5: SerialNumber: 0000:00:16.2
[    0.970233] hub 5-0:1.0: USB hub found
[    0.970245] hub 5-0:1.0: 4 ports detected
[    0.970448] ohci-pci 0000:00:12.0: OHCI PCI host controller
[    0.970453] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 6
[    0.970476] ohci-pci 0000:00:12.0: irq 18, io mem 0xfd10a000
[    1.029982] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    1.029984] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.029986] usb usb6: Product: OHCI PCI host controller
[    1.029987] usb usb6: Manufacturer: Linux 3.12-1-amd64 ohci_hcd
[    1.029988] usb usb6: SerialNumber: 0000:00:12.0
[    1.030076] hub 6-0:1.0: USB hub found
[    1.030084] hub 6-0:1.0: 5 ports detected
[    1.030222] ohci-pci 0000:00:13.0: OHCI PCI host controller
[    1.030227] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 7
[    1.030239] ohci-pci 0000:00:13.0: irq 18, io mem 0xfd108000
[    1.089918] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    1.089920] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.089921] usb usb7: Product: OHCI PCI host controller
[    1.089923] usb usb7: Manufacturer: Linux 3.12-1-amd64 ohci_hcd
[    1.089924] usb usb7: SerialNumber: 0000:00:13.0
[    1.090009] hub 7-0:1.0: USB hub found
[    1.090016] hub 7-0:1.0: 5 ports detected
[    1.090145] ohci-pci 0000:00:14.5: OHCI PCI host controller
[    1.090149] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 8
[    1.090160] ohci-pci 0000:00:14.5: irq 18, io mem 0xfd106000
[    1.149873] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    1.149875] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.149876] usb usb8: Product: OHCI PCI host controller
[    1.149877] usb usb8: Manufacturer: Linux 3.12-1-amd64 ohci_hcd
[    1.149879] usb usb8: SerialNumber: 0000:00:14.5
[    1.149961] hub 8-0:1.0: USB hub found
[    1.149967] hub 8-0:1.0: 2 ports detected
[    1.150078] ohci-pci 0000:00:16.0: OHCI PCI host controller
[    1.150082] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 9
[    1.150092] ohci-pci 0000:00:16.0: irq 18, io mem 0xfd105000
[    1.209844] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[    1.209847] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.209849] usb usb9: Product: OHCI PCI host controller
[    1.209850] usb usb9: Manufacturer: Linux 3.12-1-amd64 ohci_hcd
[    1.209851] usb usb9: SerialNumber: 0000:00:16.0
[    1.209936] hub 9-0:1.0: USB hub found
[    1.209944] hub 9-0:1.0: 4 ports detected
[    1.245819] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    1.253828] ata5: SATA link down (SStatus 0 SControl 300)
[    1.253868] ata6: SATA link down (SStatus 0 SControl 300)
[    1.262996] usb 1-1: New USB device found, idVendor=2109, idProduct=3431
[    1.262999] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.263001] usb 1-1: Product: USB2.0 Hub
[    1.263429] hub 1-1:1.0: USB hub found
[    1.263524] hub 1-1:1.0: 4 ports detected
[    1.425671] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.425691] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.425708] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.425725] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.426210] ata3.00: ATA-9: WDC WD30EFRX-68EUZN0, 80.00A80, max UDMA/133
[    1.426212] ata3.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.426285] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 80.00A80, max UDMA/133
[    1.426288] ata2.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.426539] ata1.00: ATA-8: SanDisk SDSSDHP128G, X2306RL, max UDMA/133
[    1.426541] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[    1.426793] ata3.00: configured for UDMA/133
[    1.426839] ata2.00: configured for UDMA/133
[    1.427276] ata4.00: ATAPI: ATAPI   iHAS324   Y, BL1Y, max UDMA/100
[    1.427430] ata1.00: configured for UDMA/133
[    1.427557] scsi 0:0:0:0: Direct-Access     ATA      SanDisk SDSSDHP1 X230 PQ: 0 ANSI: 5
[    1.427744] scsi 1:0:0:0: Direct-Access     ATA      WDC WD30EFRX-68E 80.0 PQ: 0 ANSI: 5
[    1.427879] scsi 2:0:0:0: Direct-Access     ATA      WDC WD30EFRX-68E 80.0 PQ: 0 ANSI: 5
[    1.429123] ata4.00: configured for UDMA/100
[    1.430910] scsi 3:0:0:0: CD-ROM            ATAPI    iHAS324   Y      BL1Y PQ: 0 ANSI: 5
[    1.434995] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[    1.435025] sd 2:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[    1.435029] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[    1.435040] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[    1.435042] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    1.435101] sd 0:0:0:0: [sda] Write Protect is off
[    1.435104] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.435114] sd 2:0:0:0: [sdc] Write Protect is off
[    1.435116] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    1.435126] sd 1:0:0:0: [sdb] Write Protect is off
[    1.435128] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.435133] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.435148] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.435159] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.435675]  sda: sda1
[    1.435795] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.435797] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.435882] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    1.435918] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.437160] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.437201] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    1.437237] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    1.437274] sr 3:0:0:0: Attached scsi generic sg3 type 5
[    1.490606]  sdc: sdc1 sdc2
[    1.490896] sd 2:0:0:0: [sdc] Attached SCSI disk
[    1.492053]  sdb: sdb1 sdb2
[    1.492299] sd 1:0:0:0: [sdb] Attached SCSI disk
[    1.541695] usb 1-1.1: new low-speed USB device number 3 using xhci_hcd
[    1.623456] platform microcode: firmware: direct-loading firmware amd-ucode/microcode_amd_fam15h.bin
[    1.626436] device-mapper: uevent: version 1.0.3
[    1.626502] device-mapper: ioctl: 4.26.0-ioctl (2013-08-15) initialised: dm-devel@redhat.com
[    1.632063] PM: Starting manual resume from disk
[    1.632065] PM: Hibernation image partition 8:17 present
[    1.632066] PM: Looking for hibernation image.
[    1.632182] PM: Image not found (code -22)
[    1.632184] PM: Hibernation image not present or could not be loaded.
[    1.639695] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    1.809802] systemd-udevd[411]: starting version 204
[    1.862820] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[    1.862827] ACPI: Power Button [PWRB]
[    1.862993] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    1.862996] ACPI: Power Button [PWRF]
[    1.863781] ACPI: acpi_idle registered with cpuidle
[    1.865297] tsc: Refined TSC clocksource calibration: 3516.188 MHz
[    1.868024] acpi-cpufreq: overriding BIOS provided _PSD data
[    1.869655] media: Linux media interface: v0.10
[    1.871791] Linux video capture interface: v2.00
[    1.879732] [drm] Initialized drm 1.1.0 20060810
[    1.879905] saa7164 driver loaded
[    1.879987] pcieport 0000:00:0a.0: driver skip pci_set_master, fix it!
[    1.880578] CORE saa7164[0]: subsystem: 0070:8940, board: Hauppauge WinTV-HVR2200 [card=9,autodetected]
[    1.880583] saa7164[0]/0: found at 0000:04:00.0, rev: 129, irq: 47, latency: 0, mmio: 0xfd800000
[    1.885771] wmi: Mapper loaded
[    1.890877] systemd-udevd[450]: renamed network interface eth0 to eth6
[    1.895100] EDAC MC: Ver: 3.0.0
[    1.895900] MCE: In-kernel MCE decoding enabled.
[    1.897849] AMD64 EDAC driver v3.4.0
[    1.898460] input: PC Speaker as /devices/platform/pcspkr/input/input4
[    1.898850] pcieport 0000:00:02.0: driver skip pci_set_master, fix it!
[    1.899182] nouveau  [  DEVICE][0000:01:00.0] BOOT0  : 0x0a8280b1
[    1.899185] nouveau  [  DEVICE][0000:01:00.0] Chipset: GT218 (NVA8)
[    1.899187] nouveau  [  DEVICE][0000:01:00.0] Family : NV50
[    1.900135] Error: Driver 'pcspkr' is already registered, aborting...
[    1.900572] nouveau  [   VBIOS][0000:01:00.0] checking PRAMIN for image...
[    1.906763] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
[    1.906798] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
[    1.906821] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[    1.906846] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[    1.906869] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[    1.906893] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[    1.906915] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[    1.906939] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
[    1.907238] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    1.907276] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb20
[    1.909335] EDAC amd64: DRAM ECC disabled.
[    1.909386] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[    1.909386]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[    1.909386]  (Note that use of the override may cause unknown side effects.)
[    1.909746] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[    1.909788] sp5100_tco: PCI Revision ID: 0x42
[    1.909832] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address
[    1.909852] sp5100_tco: Last reboot was not triggered by watchdog.
[    1.909882] sp5100_tco: initialized (0xffffc90001872b00). heartbeat=60 sec (nowayout=0)
[    1.927727] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[    1.932359] alg: No test for crc32 (crc32-pclmul)
[    1.940239] kvm: Nested Virtualization enabled
[    1.940244] kvm: Nested Paging enabled
[    1.941607] md: bind<sdc2>
[    1.964425] md: bind<sdb2>
[    1.966264] md: raid1 personality registered for level 1
[    1.966533] md/raid1:md0: active with 2 out of 2 mirrors
[    1.966613] created bitmap (22 pages) for device md0
[    1.966977] md0: bitmap initialized from disk: read 2 pages, set 0 of 44583 bits
[    1.978680] nouveau  [   VBIOS][0000:01:00.0] ... appears to be valid
[    1.978682] nouveau  [   VBIOS][0000:01:00.0] using image from PRAMIN
[    1.978778] nouveau  [   VBIOS][0000:01:00.0] BIT signature found
[    1.978780] nouveau  [   VBIOS][0000:01:00.0] version 70.18.5f.00.06
[    1.979013] nouveau  [     PFB][0000:01:00.0] RAM type: DDR3
[    1.979015] nouveau  [     PFB][0000:01:00.0] RAM size: 1024 MiB
[    1.979016] nouveau  [     PFB][0000:01:00.0]    ZCOMP: 960 tags
[    1.979685] md0: detected capacity change from 0 to 2991867756544
[    1.985049]  md0: unknown partition table
[    1.999120] systemd-udevd[453]: renamed network interface eth1 to eth5
[    2.045224] saa7164_downloadfirmware() no first image
[    2.045303] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw)
[    2.056245] saa7164 0000:04:00.0: firmware: direct-loading firmware NXP7164-2010-03-10.1.fw
[    2.056254] saa7164_downloadfirmware() firmware read 4019072 bytes.
[    2.056257] saa7164_downloadfirmware() firmware loaded.
[    2.056259] Firmware file header part 1:
[    2.056261]  .FirmwareSize = 0x0
[    2.056263]  .BSLSize = 0x0
[    2.056265]  .Reserved = 0x3d538
[    2.056267]  .Version = 0x3
[    2.056270] saa7164_downloadfirmware() SecBootLoader.FileSize = 4019072
[    2.056277] saa7164_downloadfirmware() FirmwareSize = 0x1fd6
[    2.056279] saa7164_downloadfirmware() BSLSize = 0x0
[    2.056281] saa7164_downloadfirmware() Reserved = 0x0
[    2.056283] saa7164_downloadfirmware() Version = 0x1661c00
[    2.876553] Switched to clocksource tsc
[    3.260222] nouveau  [  PTHERM][0000:01:00.0] FAN control: none / external
[    3.260228] nouveau  [  PTHERM][0000:01:00.0] fan management: disabled
[    3.260231] nouveau  [  PTHERM][0000:01:00.0] internal sensor: yes
[    3.260398] [TTM] Zone  kernel: Available graphics memory: 8251236 kiB
[    3.260400] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[    3.260401] [TTM] Initializing pool allocator
[    3.260404] [TTM] Initializing DMA pool allocator
[   18.669471] it87: Found IT8728F chip at 0x228, revision 1
[   18.669486] it87: Beeping is supported
[   19.975949] 8139too 0000:05:07.0 eth5: link up, 100Mbps, full-duplex, lpa 0xC5E1
[   83.447039] r8169 0000:03:00.0: firmware: direct-loading firmware rtl_nic/rtl8168e-3.fw
[   83.564436] r8169 0000:03:00.0 eth6: link down
[   83.564468] r8169 0000:03:00.0 eth6: link down
[   83.564484] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
[   86.701238] r8169 0000:03:00.0 eth6: link up
[   86.701249] IPv6: ADDRCONF(NETDEV_CHANGE): eth6: link becomes ready
[  866.212244] ------------[ cut here ]------------
[  866.212258] WARNING: CPU: 5 PID: 0 at /build/linux-xS3nxO/linux-3.12.6/net/sched/sch_generic.c:264 dev_watchdog+0x226/0x230()
[  866.212262] NETDEV WATCHDOG: eth6 (r8169): transmit queue 0 timed out
[  866.212264] Modules linked in: bnep rfcomm bluetooth rfkill vhost_net vhost macvtap macvlan tun xt_multiport ipt_MASQUERADE xt_CHECKSUM iptable_mangle bridge stp llc ebtable_nat ebtables parport_pc ppdev lp parport binfmt_misc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables xt_REDIRECT iptable_nat nf_nat_ipv4 nf_nat ipt_REJECT xt_tcpudp xt_LOG xt_mac nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables x_tables fuse it87 hwmon_vid loop tda18271 tda10048 joydev hid_generic snd_hda_codec_hdmi usbhid hid raid1 evdev kvm_amd md_mod kvm crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 ablk_helper cryptd lrw sp5100_tco gf128mul glue_helper fam15h_power k10temp psmouse pcspkr serio_raw nouveau edac_mce_amd edac_core i2c_piix4 snd_hda_codec_via mxm_wmi wmi video ttm drm_kms_helper saa7164 snd_hda_intel tveeprom dvb_core drm snd_hda_codec v4l2_common videodev snd_hwdep media snd_pcm i2c_algo_bit acpi_cpufreq snd_page_alloc i2c_core snd_timer snd processor soundcore button thermal_sys ext4 crc16 mbcache jbd2 dm_mod sg sd_mod sr_mod cdrom crc_t10dif crct10dif_common 8139too ohci_pci ohci_hcd ehci_pci ehci_hcd xhci_hcd ahci libahci r8169 mii libata scsi_mod usbcore usb_common
[  866.212380] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 3.12-1-amd64 #1 Debian 3.12.6-2
[  866.212383] Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./970A-D3P, BIOS F3 05/24/2013
[  866.212386]  0000000000000009 ffffffff8148c9d5 ffff88043ed43df0 ffffffff8105b572
[  866.212392]  0000000000000000 ffff88043ed43e40 0000000000000001 0000000000000005
[  866.212397]  ffff88042a4d4000 ffffffff8105b5d7 ffffffff81742f20 ffff880400000030
[  866.212402] Call Trace:
[  866.212405]  <IRQ>  [<ffffffff8148c9d5>] ? dump_stack+0x41/0x51
[  866.212419]  [<ffffffff8105b572>] ? warn_slowpath_common+0x72/0x90
[  866.212425]  [<ffffffff8105b5d7>] ? warn_slowpath_fmt+0x47/0x50
[  866.212437]  [<ffffffff813c86d6>] ? dev_watchdog+0x226/0x230
[  866.212442]  [<ffffffff813c84b0>] ? dev_graft_qdisc+0x70/0x70
[  866.212447]  [<ffffffff81066a3c>] ? call_timer_fn+0x2c/0x100
[  866.212452]  [<ffffffff813c84b0>] ? dev_graft_qdisc+0x70/0x70
[  866.212457]  [<ffffffff81067879>] ? run_timer_softirq+0x1f9/0x2b0
[  866.212466]  [<ffffffff8106071d>] ? __do_softirq+0xed/0x230
[  866.212476]  [<ffffffff8149b3dc>] ? call_softirq+0x1c/0x30
[  866.212482]  [<ffffffff810143b5>] ? do_softirq+0x55/0x90
[  866.212487]  [<ffffffff810609b5>] ? irq_exit+0x95/0xa0
[  866.212493]  [<ffffffff8103debb>] ? smp_apic_timer_interrupt+0x3b/0x50
[  866.212498]  [<ffffffff8149a71d>] ? apic_timer_interrupt+0x6d/0x80
[  866.212500]  <EOI>  [<ffffffff81377efa>] ? cpuidle_enter_state+0x4a/0xc0
[  866.212514]  [<ffffffff81378026>] ? cpuidle_idle_call+0xb6/0x1f0
[  866.212520]  [<ffffffff8101ae95>] ? arch_cpu_idle+0x5/0x30
[  866.212525]  [<ffffffff810a453e>] ? cpu_startup_entry+0xde/0x270
[  866.212531]  [<ffffffff8103c354>] ? start_secondary+0x1d4/0x230
[  866.212534] ---[ end trace cd522523d6e120ac ]---
[  866.230696] r8169 0000:03:00.0 eth6: link up
[ 1729.580858] r8169 0000:03:00.0 eth6: link up

Re: r8169 won't transmit with 3.12

[Francois Romieu]

Craig Small <csmall@enc.com.au> :
[...]
> That's fine. I was doing it to see if it would work. I'll stay with the r8169
> for now.

Thanks.

> I got a watchdog notice now, not sure if that is better or worse.

It's the usual Tx failure symptom.

[dmesg]
> [    0.000000] DMI: Gigabyte Technology Co., Ltd. To be filled by O.E.M./970A-D3P, BIOS F3 05/24/2013

(8168evl on a fairly recent motherboard, bios could be upgraded)

Did you enable the iommu in the setup ? If not, please give it a try.

-- 
Ueimor

Re: r8169 won't transmit with 3.12

[Craig Small]

On Fri, Jan 24, 2014 at 01:25:25AM +0100, Francois Romieu wrote:
> > [    0.000000] DMI: Gigabyte Technology Co., Ltd. To be filled by O.E.M./970A-D3P, BIOS F3 05/24/2013
> (8168evl on a fairly recent motherboard, bios could be upgraded)
Done!
[    0.000000] DMI: Gigabyte Technology Co., Ltd. To be filled by
O.E.M./970A-D3P, BIOS F5 08/06/2013

> Did you enable the iommu in the setup ? If not, please give it a try.
That caused some excitement...
I got a page of AMD-Vi Event logged IO_PAGE_FAULT device 02:00.0 domain
0016 messages.
And then it sat at "waiting for /dev to be fully populated"
The keyboard seemed dead at that point. I'm not sure of the exact
message and if it is important I can make it die again.

I had to turn that off to get anywhere. Then we were back where we
started.
[   97.797982] WARNING: CPU: 4 PID: 0 at /build/linux-xS3nxO/linux-3.12.6/net/sched/sch_generic.c:264 dev_watchdog+0x226/0x230()
[   97.797989] NETDEV WATCHDOG: eth6 (r8169): transmit queue 0 timed out

I've also at times rebuilt the r8169 module to add more printk lines.
I can tell you that each packet makes it to rtl8169_start_xmit and
returns NETDEV_TX_OK because the number of printk lines for my enter
and exit equal the number of tx dropped packets.

What you are seeing though is from the stock Debian kernel module. If
you have a test module code you want me to run, let me know.

 - Craig
-- 
Craig Small (@smallsees)   http://enc.com.au/       csmall at : enc.com.au
Debian GNU/Linux           http://www.debian.org/   csmall at : debian.org
GPG fingerprint:        5D2F B320 B825 D939 04D2  0519 3938 F96B DF50 FEA5

Re: r8169 won't transmit with 3.12

[Craig Small]

If it helps, I know the tx_dropped is happening on line 5837 of r8169.c

			rtl8169_unmap_tx_skb(&tp->pci_dev->dev, tx_skb,
					     tp->TxDescArray + entry);
			if (skb) {
				tp->dev->stats.tx_dropped++;
				dev_kfree_skb(skb);
				tx_skb->skb = NULL;
			}


On Wed, Jan 22, 2014 at 12:36:30AM +0100, Francois Romieu wrote:
> Craig Small <csmall@enc.com.au> :
> [...]
> > It's a new setup so it might of never worked. It's not likely to be a
> > hardware problem as its three different devices.
> 
> You may check that the onboard nic device does not even work when the
> extra PCI-e card aren't plugged.
> 
> > I've sent what I think you might need for starters, but if there
> > is extra stuff you'd like to see, let me know.
> 
> A complete dmesg including the XID lines that the r8169 driver prints
> would be welcome.
> 
> > The problem shows up the same, the TX dropped counter increments.
> > I'm not sure why 42 packets made it out (or even if they really did)
> > Receive works fine, I can even start up wireshark and see packets
> > pass by.
> > 
> > eth0      Link encap:Ethernet  HWaddr 00:e0:4c:80:66:57  
> >           inet addr:192.168.1.222  Bcast:192.168.1.255  Mask:255.255.255.0
> >           inet6 addr: fe80::2e0:4cff:fe80:6657/64 Scope:Link
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:8252 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:42 errors:0 dropped:8029 overruns:0 carrier:0
> 
> There are very few places where the r8169 driver modifies tx_dropped.
> 
> Please increase the driver verbosity with the 'msglvl' option of ethtool.
> 
> [...]
> > ethtool -S shows a similar story, not sure if the rx_missed counter
> > is another problem:
> 
> It seems safe to ignore as long as it does not change after startup.
> 
> -- 
> Ueimor

-- 
Craig Small (@smallsees)   http://enc.com.au/       csmall at : enc.com.au
Debian GNU/Linux           http://www.debian.org/   csmall at : debian.org
GPG fingerprint:        5D2F B320 B825 D939 04D2  0519 3938 F96B DF50 FEA5