* [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC [not found] <3a7fed78df06416da20ec72f14111c97@inventec.com> @ 2021-10-14 2:31 ` Lin.TommySC 林世欽 TAO 2021-10-18 23:43 ` Joel Stanley 0 siblings, 1 reply; 5+ messages in thread From: Lin.TommySC 林世欽 TAO @ 2021-10-14 2:31 UTC (permalink / raw) To: openbmc; +Cc: Ye.Vic 葉宇清 TAO, Mohammed.Habeeb ISV Initial introduction of Inventec Transformers x86 family equipped with AST2600 BMC SoC. Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com> --- arch/arm/boot/dts/Makefile | 1 + .../dts/aspeed-bmc-inventec-transformers.dts | 457 ++++++++++++++++++ 2 files changed, 458 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 48d48c85de9e..930b8ba6c3c5 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1407,6 +1407,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-intel-s2600wf.dtb \ aspeed-bmc-inspur-fp5280g2.dtb \ aspeed-bmc-inspur-nf5280m6.dtb \ + aspeed-bmc-inventec-transformers.dtb \ aspeed-bmc-lenovo-hr630.dtb \ aspeed-bmc-lenovo-hr855xg2.dtb \ aspeed-bmc-microsoft-olympus.dtb \ diff --git a/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts b/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts new file mode 100644 index 000000000000..71e85694c3c7 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts @@ -0,0 +1,457 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2021 Inventec Corp. + +/dts-v1/; + +#include "aspeed-g6.dtsi" +#include "aspeed-g6-pinctrl.dtsi" +#include <dt-bindings/i2c/i2c.h> +#include <dt-bindings/gpio/aspeed-gpio.h> + +/ { + model = "TRANSFORMERS BMC"; + compatible = "inventec,transformer-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + }; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200n8"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>; + }; + + leds { + compatible = "gpio-leds"; + + // UID led + uid { + label = "UID_LED"; + gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>; + }; + + // Heart beat led + heartbeat { + label = "HB_LED"; + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>; + }; + }; + + pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_tach0_default + &pinctrl_pwm1_default &pinctrl_tach1_default + &pinctrl_pwm2_default &pinctrl_tach2_default + &pinctrl_pwm3_default &pinctrl_tach3_default + &pinctrl_pwm4_default &pinctrl_tach4_default + &pinctrl_pwm5_default &pinctrl_tach5_default + &pinctrl_pwm6_default &pinctrl_tach6_default + &pinctrl_pwm7_default &pinctrl_tach7_default + &pinctrl_tach8_default + &pinctrl_tach9_default + &pinctrl_tach10_default + &pinctrl_tach11_default + &pinctrl_tach12_default + &pinctrl_tach13_default + &pinctrl_tach14_default + &pinctrl_tach15_default>; + fan@0 { + reg = <0x00>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x00>; + aspeed,min_rpm = <750000>; + }; + + fan@1 { + reg = <0x01>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x01>; + aspeed,min_rpm = <750000>; + }; + + fan@2 { + reg = <0x02>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x02>; + aspeed,min_rpm = <750000>; + }; + + fan@3 { + reg = <0x03>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x03>; + aspeed,min_rpm = <750000>; + }; + + fan@4 { + reg = <0x04>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x04>; + aspeed,min_rpm = <750000>; + }; + + fan@5 { + reg = <0x05>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x05>; + aspeed,min_rpm = <750000>; + }; + + fan@6 { + reg = <0x06>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x06>; + aspeed,min_rpm = <750000>; + }; + + fan@7 { + reg = <0x07>; + aspeed,target_pwm = <25000>; + cooling-levels = <125 151 177 203 229 255>; + aspeed,fan-tach-ch = <0x07>; + aspeed,min_rpm = <750000>; + }; + + fan@8 { + reg = <0x08>; + aspeed,fan-tach-ch = <0x08>; + }; + + fan@9 { + reg = <0x09>; + aspeed,fan-tach-ch = <0x09>; + }; + + fan@10 { + reg = <0x0a>; + aspeed,fan-tach-ch = <0x0a>; + }; + + fan@11 { + reg = <0x0b>; + aspeed,fan-tach-ch = <0x0b>; + }; + + fan@12 { + reg = <0x0c>; + aspeed,fan-tach-ch = <0x0c>; + }; + + fan@13 { + reg = <0x0d>; + aspeed,fan-tach-ch = <0x0d>; + }; + + fan@14 { + reg = <0x0e>; + aspeed,fan-tach-ch = <0x0e>; + }; + + fan@15 { + reg = <0x0f>; + aspeed,fan-tach-ch = <0x0f>; + }; + }; +}; + +&mdio0 { + status = "okay"; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mac3 { + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <ðphy0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii4_default>; +}; + +&fmc { + status = "okay"; + + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-max-frequency = <33000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; +#include "openbmc-flash-layout.dtsi" + }; + + flash@1 { + status = "okay"; + m25p,fast-read; + label = "bmc2"; + spi-max-frequency = <33000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bios"; + spi-max-frequency = <33000000>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <1>; + }; +}; + +&wdt1 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + //Set bmc' slave address; + bmc_slave@10 { + compatible = "ipmb-dev"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + i2c-protocol; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + // FRU AT24C512C-SSHM-T + status = "okay"; + eeprom@50 { + compatible = "atmel,24c512"; + reg = <0x50>; + pagesize = <128>; + }; +}; + +&i2c5 { + status = "okay"; +}; + +&i2c6 { + status = "okay"; + + tmp75@49 { + compatible = "ti,tmp75"; + reg = <0x49>; + }; + + tmp75@4f { + compatible = "ti,tmp75"; + reg = <0x4f>; + }; + + tmp468@48 { + compatible = "ti,tmp468"; + reg = <0x48>; + }; +}; + +&i2c7 { + status = "okay"; + adm1278@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + + +&i2c8 { + // FRU AT24C512C-SSHM-T + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c512"; + reg = <0x51>; + pagesize = <128>; + }; + + eeprom@53 { + compatible = "atmel,24c512"; + reg = <0x53>; + pagesize = <128>; + }; +}; + +&i2c9 { + // M.2 + status = "okay"; +}; + +&i2c10 { + // I2C EXPANDER + status = "okay"; + + i2c-switch@71 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + }; + + i2c-switch@73 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x73>; + }; +}; + +&i2c11 { + // I2C EXPANDER + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + pcie_eeprom_riser1: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + eeprom@55 { + compatible = "atmel,24c512"; + reg = <0x55>; + pagesize = <128>; + }; + }; + + pcie_eeprom_riser2: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + eeprom@55 { + compatible = "atmel,24c512"; + reg = <0x55>; + pagesize = <128>; + }; + }; + + pcie_eeprom_riser3: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + eeprom@55 { + compatible = "atmel,24c512"; + reg = <0x55>; + pagesize = <128>; + }; + }; + }; +}; + +&i2c12 { + status = "okay"; + + psu0:psu0@58 { + compatible = "pmbus"; + reg = <0x58>; + }; +}; + +&gpio0 { + status = "okay"; + gpio-line-names = + /*A0-A7*/ "","","","","","","","", + /*B0-B7*/ "presence-ps0","power-chassis-good","","","","","presence-ps1","", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "","","","","","","","", + /*E0-E7*/ "","","","","","","","", + /*F0-F7*/ "","","","","power-chassis-control","","","", + /*G0-G7*/ "","","jtag-mux","","","","","", + /*H0-H7*/ "","","","","reset-button","power-button","","", + /*I0-I7*/ "","","","","","","","", + /*J0-J7*/ "","","","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "","","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","tck-mux","","","","", + /*Q0-Q7*/ "","","","","","","","", + /*R0-R7*/ "","","","","","","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","nmi-button","","","","","","", + /*V0-V7*/ "","","","","power-config-full-load","","","", + /*W0-W7*/ "","","","","","","","", + /*X0-X7*/ "","","","","","","","", + /*Y0-Y7*/ "","","","","","","","", + /*Z0-Z7*/ "","","","","","","","", + /*AA0-AA7*/ "","","","","","","","", + /*AB0-AB7*/ "","","","","","","","", + /*AC0-AC7*/ "","","","","","","",""; +}; + +&lpc_snoop { + status = "okay"; + snoop-ports = <0x80>; +}; + +&emmc_controller { + status = "okay"; +}; + +&emmc { + status = "okay"; + non-removable; + max-frequency = <52000000>; + bus-width = <8>; +}; + +&vhub { + status = "okay"; + aspeed,vhub-downstream-ports = <7>; + aspeed,vhub-generic-endpoints = <21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2ad_default>; +}; + +&rtc { + status = "okay"; +}; -- 2.33.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC 2021-10-14 2:31 ` [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC Lin.TommySC 林世欽 TAO @ 2021-10-18 23:43 ` Joel Stanley 2021-10-18 23:48 ` Joel Stanley 0 siblings, 1 reply; 5+ messages in thread From: Joel Stanley @ 2021-10-18 23:43 UTC (permalink / raw) To: Lin.TommySC 林世欽 TAO Cc: Ye.Vic 葉宇清 TAO, openbmc, Mohammed.Habeeb ISV On Mon, 18 Oct 2021 at 22:51, Lin.TommySC 林世欽 TAO <Lin.TommySC@inventec.com> wrote: > > Initial introduction of Inventec Transformers x86 family equipped with AST2600 BMC SoC. > > Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Thanks! I've applied this to the aspeed tree (but I've already sent my pull request for v5.16) and to the openbmc tree. Cheers, Joel > --- > arch/arm/boot/dts/Makefile | 1 + > .../dts/aspeed-bmc-inventec-transformers.dts | 457 ++++++++++++++++++ > 2 files changed, 458 insertions(+) > create mode 100644 arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 48d48c85de9e..930b8ba6c3c5 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -1407,6 +1407,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ > aspeed-bmc-intel-s2600wf.dtb \ > aspeed-bmc-inspur-fp5280g2.dtb \ > aspeed-bmc-inspur-nf5280m6.dtb \ > + aspeed-bmc-inventec-transformers.dtb \ > aspeed-bmc-lenovo-hr630.dtb \ > aspeed-bmc-lenovo-hr855xg2.dtb \ > aspeed-bmc-microsoft-olympus.dtb \ > diff --git a/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts b/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts > new file mode 100644 > index 000000000000..71e85694c3c7 > --- /dev/null > +++ b/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts > @@ -0,0 +1,457 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +// Copyright 2021 Inventec Corp. > + > +/dts-v1/; > + > +#include "aspeed-g6.dtsi" > +#include "aspeed-g6-pinctrl.dtsi" > +#include <dt-bindings/i2c/i2c.h> > +#include <dt-bindings/gpio/aspeed-gpio.h> > + > +/ { > + model = "TRANSFORMERS BMC"; > + compatible = "inventec,transformer-bmc", "aspeed,ast2600"; > + > + aliases { > + serial4 = &uart5; > + }; > + > + chosen { > + stdout-path = &uart5; > + bootargs = "console=ttyS4,115200n8"; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x80000000 0x80000000>; > + }; > + > + iio-hwmon { > + compatible = "iio-hwmon"; > + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + // UID led > + uid { > + label = "UID_LED"; > + gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>; > + }; > + > + // Heart beat led > + heartbeat { > + label = "HB_LED"; > + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>; > + }; > + }; > + > + pwm_tacho { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_tach0_default > + &pinctrl_pwm1_default &pinctrl_tach1_default > + &pinctrl_pwm2_default &pinctrl_tach2_default > + &pinctrl_pwm3_default &pinctrl_tach3_default > + &pinctrl_pwm4_default &pinctrl_tach4_default > + &pinctrl_pwm5_default &pinctrl_tach5_default > + &pinctrl_pwm6_default &pinctrl_tach6_default > + &pinctrl_pwm7_default &pinctrl_tach7_default > + &pinctrl_tach8_default > + &pinctrl_tach9_default > + &pinctrl_tach10_default > + &pinctrl_tach11_default > + &pinctrl_tach12_default > + &pinctrl_tach13_default > + &pinctrl_tach14_default > + &pinctrl_tach15_default>; > + fan@0 { > + reg = <0x00>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x00>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@1 { > + reg = <0x01>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x01>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@2 { > + reg = <0x02>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x02>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@3 { > + reg = <0x03>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x03>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@4 { > + reg = <0x04>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x04>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@5 { > + reg = <0x05>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x05>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@6 { > + reg = <0x06>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x06>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@7 { > + reg = <0x07>; > + aspeed,target_pwm = <25000>; > + cooling-levels = <125 151 177 203 229 255>; > + aspeed,fan-tach-ch = <0x07>; > + aspeed,min_rpm = <750000>; > + }; > + > + fan@8 { > + reg = <0x08>; > + aspeed,fan-tach-ch = <0x08>; > + }; > + > + fan@9 { > + reg = <0x09>; > + aspeed,fan-tach-ch = <0x09>; > + }; > + > + fan@10 { > + reg = <0x0a>; > + aspeed,fan-tach-ch = <0x0a>; > + }; > + > + fan@11 { > + reg = <0x0b>; > + aspeed,fan-tach-ch = <0x0b>; > + }; > + > + fan@12 { > + reg = <0x0c>; > + aspeed,fan-tach-ch = <0x0c>; > + }; > + > + fan@13 { > + reg = <0x0d>; > + aspeed,fan-tach-ch = <0x0d>; > + }; > + > + fan@14 { > + reg = <0x0e>; > + aspeed,fan-tach-ch = <0x0e>; > + }; > + > + fan@15 { > + reg = <0x0f>; > + aspeed,fan-tach-ch = <0x0f>; > + }; > + }; > +}; > + > +&mdio0 { > + status = "okay"; > + > + ethphy0: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > +}; > + > +&mac3 { > + status = "okay"; > + phy-mode = "rgmii"; > + phy-handle = <ðphy0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rgmii4_default>; > +}; > + > +&fmc { > + status = "okay"; > + > + flash@0 { > + status = "okay"; > + m25p,fast-read; > + label = "bmc"; > + spi-max-frequency = <33000000>; > + spi-tx-bus-width = <2>; > + spi-rx-bus-width = <2>; > +#include "openbmc-flash-layout.dtsi" > + }; > + > + flash@1 { > + status = "okay"; > + m25p,fast-read; > + label = "bmc2"; > + spi-max-frequency = <33000000>; > + spi-tx-bus-width = <2>; > + spi-rx-bus-width = <2>; > + }; > +}; > + > +&spi1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi1_default>; > + > + flash@0 { > + status = "okay"; > + m25p,fast-read; > + label = "bios"; > + spi-max-frequency = <33000000>; > + spi-tx-bus-width = <1>; > + spi-rx-bus-width = <1>; > + }; > +}; > + > +&wdt1 { > + status = "okay"; > +}; > + > +&uart1 { > + status = "okay"; > +}; > + > +&uart5 { > + status = "okay"; > +}; > + > +&i2c0 { > + status = "okay"; > + > + //Set bmc' slave address; > + bmc_slave@10 { > + compatible = "ipmb-dev"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + i2c-protocol; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > +}; > + > +&i2c3 { > + // FRU AT24C512C-SSHM-T > + status = "okay"; > + eeprom@50 { > + compatible = "atmel,24c512"; > + reg = <0x50>; > + pagesize = <128>; > + }; > +}; > + > +&i2c5 { > + status = "okay"; > +}; > + > +&i2c6 { > + status = "okay"; > + > + tmp75@49 { > + compatible = "ti,tmp75"; > + reg = <0x49>; > + }; > + > + tmp75@4f { > + compatible = "ti,tmp75"; > + reg = <0x4f>; > + }; > + > + tmp468@48 { > + compatible = "ti,tmp468"; > + reg = <0x48>; > + }; > +}; > + > +&i2c7 { > + status = "okay"; > + adm1278@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > + > +&i2c8 { > + // FRU AT24C512C-SSHM-T > + status = "okay"; > + > + eeprom@51 { > + compatible = "atmel,24c512"; > + reg = <0x51>; > + pagesize = <128>; > + }; > + > + eeprom@53 { > + compatible = "atmel,24c512"; > + reg = <0x53>; > + pagesize = <128>; > + }; > +}; > + > +&i2c9 { > + // M.2 > + status = "okay"; > +}; > + > +&i2c10 { > + // I2C EXPANDER > + status = "okay"; > + > + i2c-switch@71 { > + compatible = "nxp,pca9544"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x71>; > + }; > + > + i2c-switch@73 { > + compatible = "nxp,pca9544"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x73>; > + }; > +}; > + > +&i2c11 { > + // I2C EXPANDER > + status = "okay"; > + > + i2c-switch@70 { > + compatible = "nxp,pca9544"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x70>; > + > + pcie_eeprom_riser1: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + eeprom@55 { > + compatible = "atmel,24c512"; > + reg = <0x55>; > + pagesize = <128>; > + }; > + }; > + > + pcie_eeprom_riser2: i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + > + eeprom@55 { > + compatible = "atmel,24c512"; > + reg = <0x55>; > + pagesize = <128>; > + }; > + }; > + > + pcie_eeprom_riser3: i2c@2 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <2>; > + > + eeprom@55 { > + compatible = "atmel,24c512"; > + reg = <0x55>; > + pagesize = <128>; > + }; > + }; > + }; > +}; > + > +&i2c12 { > + status = "okay"; > + > + psu0:psu0@58 { > + compatible = "pmbus"; > + reg = <0x58>; > + }; > +}; > + > +&gpio0 { > + status = "okay"; > + gpio-line-names = > + /*A0-A7*/ "","","","","","","","", > + /*B0-B7*/ "presence-ps0","power-chassis-good","","","","","presence-ps1","", > + /*C0-C7*/ "","","","","","","","", > + /*D0-D7*/ "","","","","","","","", > + /*E0-E7*/ "","","","","","","","", > + /*F0-F7*/ "","","","","power-chassis-control","","","", > + /*G0-G7*/ "","","jtag-mux","","","","","", > + /*H0-H7*/ "","","","","reset-button","power-button","","", > + /*I0-I7*/ "","","","","","","","", > + /*J0-J7*/ "","","","","","","","", > + /*K0-K7*/ "","","","","","","","", > + /*L0-L7*/ "","","","","","","","", > + /*M0-M7*/ "","","","","","","","", > + /*N0-N7*/ "","","","","","","","", > + /*O0-O7*/ "","","","","","","","", > + /*P0-P7*/ "","","","tck-mux","","","","", > + /*Q0-Q7*/ "","","","","","","","", > + /*R0-R7*/ "","","","","","","","", > + /*S0-S7*/ "","","","","","","","", > + /*T0-T7*/ "","","","","","","","", > + /*U0-U7*/ "","nmi-button","","","","","","", > + /*V0-V7*/ "","","","","power-config-full-load","","","", > + /*W0-W7*/ "","","","","","","","", > + /*X0-X7*/ "","","","","","","","", > + /*Y0-Y7*/ "","","","","","","","", > + /*Z0-Z7*/ "","","","","","","","", > + /*AA0-AA7*/ "","","","","","","","", > + /*AB0-AB7*/ "","","","","","","","", > + /*AC0-AC7*/ "","","","","","","",""; > +}; > + > +&lpc_snoop { > + status = "okay"; > + snoop-ports = <0x80>; > +}; > + > +&emmc_controller { > + status = "okay"; > +}; > + > +&emmc { > + status = "okay"; > + non-removable; > + max-frequency = <52000000>; > + bus-width = <8>; > +}; > + > +&vhub { > + status = "okay"; > + aspeed,vhub-downstream-ports = <7>; > + aspeed,vhub-generic-endpoints = <21>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb2ad_default>; > +}; > + > +&rtc { > + status = "okay"; > +}; > -- > 2.33.0 > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC 2021-10-18 23:43 ` Joel Stanley @ 2021-10-18 23:48 ` Joel Stanley 2021-10-19 2:06 ` Lin.TommySC 林世欽 TAO 0 siblings, 1 reply; 5+ messages in thread From: Joel Stanley @ 2021-10-18 23:48 UTC (permalink / raw) To: Lin.TommySC 林世欽 TAO Cc: Ye.Vic 葉宇清 TAO, openbmc, Mohammed.Habeeb ISV On Mon, 18 Oct 2021 at 23:43, Joel Stanley <joel@jms.id.au> wrote: > > On Mon, 18 Oct 2021 at 22:51, Lin.TommySC 林世欽 TAO > <Lin.TommySC@inventec.com> wrote: > > > > Initial introduction of Inventec Transformers x86 family equipped with AST2600 BMC SoC. > > > > Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com> > > Reviewed-by: Joel Stanley <joel@jms.id.au> > > Thanks! I've applied this to the aspeed tree (but I've already sent my > pull request for v5.16) and to the openbmc tree. I spoke too soon! The patch introduces a lot of warnings that I will get you to fix before I apply. Please apply your patch to v5.15-rc1 and build it to ensure you have seen all of the warnings. > > + pwm_tacho { > > + status = "okay"; > > + pinctrl-names = "default"; > > + fan@0 { > > + reg = <0x00>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x00>; > > + aspeed,min_rpm = <750000>; DTC arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:70.24-37: Warning (reg_format): /pwm_tacho/fan@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:78.24-37: Warning (reg_format): /pwm_tacho/fan@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:86.24-37: Warning (reg_format): /pwm_tacho/fan@2:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:94.24-37: Warning (reg_format): /pwm_tacho/fan@3:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:102.24-37: Warning (reg_format): /pwm_tacho/fan@4:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:110.24-37: Warning (reg_format): /pwm_tacho/fan@5:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:118.24-37: Warning (reg_format): /pwm_tacho/fan@6:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:126.24-37: Warning (reg_format): /pwm_tacho/fan@7:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:134.24-37: Warning (reg_format): /pwm_tacho/fan@8:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:139.24-37: Warning (reg_format): /pwm_tacho/fan@9:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:144.24-37: Warning (reg_format): /pwm_tacho/fan@10:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:149.24-37: Warning (reg_format): /pwm_tacho/fan@11:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:154.24-37: Warning (reg_format): /pwm_tacho/fan@12:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:159.24-37: Warning (reg_format): /pwm_tacho/fan@13:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:164.24-37: Warning (reg_format): /pwm_tacho/fan@14:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:169.24-37: Warning (reg_format): /pwm_tacho/fan@15:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (pci_device_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format' ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:69.22-75.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@0: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:69.22-75.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@0: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:77.22-83.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@1: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:77.22-83.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@1: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:85.22-91.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@2: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:85.22-91.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@2: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:93.22-99.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@3: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:93.22-99.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@3: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:101.22-107.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@4: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:101.22-107.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@4: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:109.22-115.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@5: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:109.22-115.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@5: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:117.22-123.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@6: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:117.22-123.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@6: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:125.22-131.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@7: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:125.22-131.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@7: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:133.22-136.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@8: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:133.22-136.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@8: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:138.22-141.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@9: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:138.22-141.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@9: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:143.23-146.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@10: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:143.23-146.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@10: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:148.23-151.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@11: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:148.23-151.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@11: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:153.23-156.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@12: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:153.23-156.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@12: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:158.23-161.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@13: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:158.23-161.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@13: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:163.23-166.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@14: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:163.23-166.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@14: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:168.23-171.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@15: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:168.23-171.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@15: Relying on default #size-cells value > > + }; > > + > > + fan@1 { > > + reg = <0x01>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x01>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@2 { > > + reg = <0x02>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x02>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@3 { > > + reg = <0x03>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x03>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@4 { > > + reg = <0x04>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x04>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@5 { > > + reg = <0x05>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x05>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@6 { > > + reg = <0x06>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x06>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@7 { > > + reg = <0x07>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x07>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@8 { > > + reg = <0x08>; > > + aspeed,fan-tach-ch = <0x08>; > > + }; > > + > > + fan@9 { > > + reg = <0x09>; > > + aspeed,fan-tach-ch = <0x09>; > > + }; > > + > > + fan@10 { > > + reg = <0x0a>; > > + aspeed,fan-tach-ch = <0x0a>; > > + }; > > + > > + fan@11 { > > + reg = <0x0b>; > > + aspeed,fan-tach-ch = <0x0b>; > > + }; > > + > > + fan@12 { > > + reg = <0x0c>; > > + aspeed,fan-tach-ch = <0x0c>; > > + }; > > + > > + fan@13 { > > + reg = <0x0d>; > > + aspeed,fan-tach-ch = <0x0d>; > > + }; > > + > > + fan@14 { > > + reg = <0x0e>; > > + aspeed,fan-tach-ch = <0x0e>; > > + }; > > + > > + fan@15 { > > + reg = <0x0f>; > > + aspeed,fan-tach-ch = <0x0f>; > > + }; > > + }; > > +}; > > + > > +&mdio0 { > > + status = "okay"; > > + > > + ethphy0: ethernet-phy@0 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + }; > > +}; > > + > > +&mac3 { > > + status = "okay"; > > + phy-mode = "rgmii"; > > + phy-handle = <ðphy0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_rgmii4_default>; > > +}; > > + > > +&fmc { > > + status = "okay"; > > + > > + flash@0 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bmc"; > > + spi-max-frequency = <33000000>; > > + spi-tx-bus-width = <2>; > > + spi-rx-bus-width = <2>; > > +#include "openbmc-flash-layout.dtsi" > > + }; > > + > > + flash@1 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bmc2"; > > + spi-max-frequency = <33000000>; > > + spi-tx-bus-width = <2>; > > + spi-rx-bus-width = <2>; > > + }; > > +}; > > + > > +&spi1 { > > + status = "okay"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_spi1_default>; > > + > > + flash@0 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bios"; > > + spi-max-frequency = <33000000>; > > + spi-tx-bus-width = <1>; > > + spi-rx-bus-width = <1>; > > + }; > > +}; > > + > > +&wdt1 { > > + status = "okay"; > > +}; > > + > > +&uart1 { > > + status = "okay"; > > +}; > > + > > +&uart5 { > > + status = "okay"; > > +}; > > + > > +&i2c0 { > > + status = "okay"; > > + > > + //Set bmc' slave address; > > + bmc_slave@10 { > > + compatible = "ipmb-dev"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + i2c-protocol; > > + }; > > +}; > > + > > +&i2c2 { > > + status = "okay"; > > +}; > > + > > +&i2c3 { > > + // FRU AT24C512C-SSHM-T > > + status = "okay"; > > + eeprom@50 { > > + compatible = "atmel,24c512"; > > + reg = <0x50>; > > + pagesize = <128>; > > + }; > > +}; > > + > > +&i2c5 { > > + status = "okay"; > > +}; > > + > > +&i2c6 { > > + status = "okay"; > > + > > + tmp75@49 { > > + compatible = "ti,tmp75"; > > + reg = <0x49>; > > + }; > > + > > + tmp75@4f { > > + compatible = "ti,tmp75"; > > + reg = <0x4f>; > > + }; > > + > > + tmp468@48 { > > + compatible = "ti,tmp468"; > > + reg = <0x48>; > > + }; > > +}; > > + > > +&i2c7 { > > + status = "okay"; > > + adm1278@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > + > > +&i2c8 { > > + // FRU AT24C512C-SSHM-T > > + status = "okay"; > > + > > + eeprom@51 { > > + compatible = "atmel,24c512"; > > + reg = <0x51>; > > + pagesize = <128>; > > + }; > > + > > + eeprom@53 { > > + compatible = "atmel,24c512"; > > + reg = <0x53>; > > + pagesize = <128>; > > + }; > > +}; > > + > > +&i2c9 { > > + // M.2 > > + status = "okay"; > > +}; > > + > > +&i2c10 { > > + // I2C EXPANDER > > + status = "okay"; > > + > > + i2c-switch@71 { > > + compatible = "nxp,pca9544"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x71>; > > + }; > > + > > + i2c-switch@73 { > > + compatible = "nxp,pca9544"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x73>; > > + }; > > +}; > > + > > +&i2c11 { > > + // I2C EXPANDER > > + status = "okay"; > > + > > + i2c-switch@70 { > > + compatible = "nxp,pca9544"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x70>; > > + > > + pcie_eeprom_riser1: i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0>; > > + > > + eeprom@55 { > > + compatible = "atmel,24c512"; > > + reg = <0x55>; > > + pagesize = <128>; > > + }; > > + }; > > + > > + pcie_eeprom_riser2: i2c@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <1>; > > + > > + eeprom@55 { > > + compatible = "atmel,24c512"; > > + reg = <0x55>; > > + pagesize = <128>; > > + }; > > + }; > > + > > + pcie_eeprom_riser3: i2c@2 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <2>; > > + > > + eeprom@55 { > > + compatible = "atmel,24c512"; > > + reg = <0x55>; > > + pagesize = <128>; > > + }; > > + }; > > + }; > > +}; > > + > > +&i2c12 { > > + status = "okay"; > > + > > + psu0:psu0@58 { > > + compatible = "pmbus"; > > + reg = <0x58>; > > + }; > > +}; > > + > > +&gpio0 { > > + status = "okay"; > > + gpio-line-names = > > + /*A0-A7*/ "","","","","","","","", > > + /*B0-B7*/ "presence-ps0","power-chassis-good","","","","","presence-ps1","", > > + /*C0-C7*/ "","","","","","","","", > > + /*D0-D7*/ "","","","","","","","", > > + /*E0-E7*/ "","","","","","","","", > > + /*F0-F7*/ "","","","","power-chassis-control","","","", > > + /*G0-G7*/ "","","jtag-mux","","","","","", > > + /*H0-H7*/ "","","","","reset-button","power-button","","", > > + /*I0-I7*/ "","","","","","","","", > > + /*J0-J7*/ "","","","","","","","", > > + /*K0-K7*/ "","","","","","","","", > > + /*L0-L7*/ "","","","","","","","", > > + /*M0-M7*/ "","","","","","","","", > > + /*N0-N7*/ "","","","","","","","", > > + /*O0-O7*/ "","","","","","","","", > > + /*P0-P7*/ "","","","tck-mux","","","","", > > + /*Q0-Q7*/ "","","","","","","","", > > + /*R0-R7*/ "","","","","","","","", > > + /*S0-S7*/ "","","","","","","","", > > + /*T0-T7*/ "","","","","","","","", > > + /*U0-U7*/ "","nmi-button","","","","","","", > > + /*V0-V7*/ "","","","","power-config-full-load","","","", > > + /*W0-W7*/ "","","","","","","","", > > + /*X0-X7*/ "","","","","","","","", > > + /*Y0-Y7*/ "","","","","","","","", > > + /*Z0-Z7*/ "","","","","","","","", > > + /*AA0-AA7*/ "","","","","","","","", > > + /*AB0-AB7*/ "","","","","","","","", > > + /*AC0-AC7*/ "","","","","","","",""; > > +}; > > + > > +&lpc_snoop { > > + status = "okay"; > > + snoop-ports = <0x80>; > > +}; > > + > > +&emmc_controller { > > + status = "okay"; > > +}; > > + > > +&emmc { > > + status = "okay"; > > + non-removable; > > + max-frequency = <52000000>; > > + bus-width = <8>; > > +}; > > + > > +&vhub { > > + status = "okay"; > > + aspeed,vhub-downstream-ports = <7>; > > + aspeed,vhub-generic-endpoints = <21>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usb2ad_default>; > > +}; > > + > > +&rtc { > > + status = "okay"; > > +}; > > -- > > 2.33.0 > > ^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC 2021-10-18 23:48 ` Joel Stanley @ 2021-10-19 2:06 ` Lin.TommySC 林世欽 TAO 2021-10-19 2:10 ` Joel Stanley 0 siblings, 1 reply; 5+ messages in thread From: Lin.TommySC 林世欽 TAO @ 2021-10-19 2:06 UTC (permalink / raw) To: Joel Stanley Cc: Ye.Vic 葉宇清 TAO, openbmc, Mohammed.Habeeb ISV Hi Joel, Could you give some hint on how to upgrade to v5.15-rc1? I don't see this tag in upstream github https://github.com/openbmc/linux. BR Tommy ________________________________________ 寄件者: Joel Stanley <joel@jms.id.au> 寄件日期: 2021年10月19日 上午 07:48 收件者: Lin.TommySC 林世欽 TAO 副本: openbmc@lists.ozlabs.org; Ye.Vic 葉宇清 TAO; Mohammed.Habeeb ISV 主旨: Re: [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC On Mon, 18 Oct 2021 at 23:43, Joel Stanley <joel@jms.id.au> wrote: > > On Mon, 18 Oct 2021 at 22:51, Lin.TommySC 林世欽 TAO > <Lin.TommySC@inventec.com> wrote: > > > > Initial introduction of Inventec Transformers x86 family equipped with AST2600 BMC SoC. > > > > Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com> > > Reviewed-by: Joel Stanley <joel@jms.id.au> > > Thanks! I've applied this to the aspeed tree (but I've already sent my > pull request for v5.16) and to the openbmc tree. I spoke too soon! The patch introduces a lot of warnings that I will get you to fix before I apply. Please apply your patch to v5.15-rc1 and build it to ensure you have seen all of the warnings. > > + pwm_tacho { > > + status = "okay"; > > + pinctrl-names = "default"; > > + fan@0 { > > + reg = <0x00>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x00>; > > + aspeed,min_rpm = <750000>; DTC arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:70.24-37: Warning (reg_format): /pwm_tacho/fan@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:78.24-37: Warning (reg_format): /pwm_tacho/fan@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:86.24-37: Warning (reg_format): /pwm_tacho/fan@2:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:94.24-37: Warning (reg_format): /pwm_tacho/fan@3:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:102.24-37: Warning (reg_format): /pwm_tacho/fan@4:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:110.24-37: Warning (reg_format): /pwm_tacho/fan@5:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:118.24-37: Warning (reg_format): /pwm_tacho/fan@6:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:126.24-37: Warning (reg_format): /pwm_tacho/fan@7:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:134.24-37: Warning (reg_format): /pwm_tacho/fan@8:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:139.24-37: Warning (reg_format): /pwm_tacho/fan@9:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:144.24-37: Warning (reg_format): /pwm_tacho/fan@10:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:149.24-37: Warning (reg_format): /pwm_tacho/fan@11:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:154.24-37: Warning (reg_format): /pwm_tacho/fan@12:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:159.24-37: Warning (reg_format): /pwm_tacho/fan@13:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:164.24-37: Warning (reg_format): /pwm_tacho/fan@14:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:169.24-37: Warning (reg_format): /pwm_tacho/fan@15:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (pci_device_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format' ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:69.22-75.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@0: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:69.22-75.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@0: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:77.22-83.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@1: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:77.22-83.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@1: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:85.22-91.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@2: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:85.22-91.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@2: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:93.22-99.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@3: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:93.22-99.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@3: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:101.22-107.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@4: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:101.22-107.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@4: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:109.22-115.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@5: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:109.22-115.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@5: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:117.22-123.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@6: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:117.22-123.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@6: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:125.22-131.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@7: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:125.22-131.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@7: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:133.22-136.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@8: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:133.22-136.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@8: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:138.22-141.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@9: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:138.22-141.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@9: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:143.23-146.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@10: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:143.23-146.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@10: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:148.23-151.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@11: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:148.23-151.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@11: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:153.23-156.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@12: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:153.23-156.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@12: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:158.23-161.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@13: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:158.23-161.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@13: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:163.23-166.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@14: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:163.23-166.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@14: Relying on default #size-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:168.23-171.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@15: Relying on default #address-cells value ../arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts:168.23-171.18: Warning (avoid_default_addr_size): /pwm_tacho/fan@15: Relying on default #size-cells value > > + }; > > + > > + fan@1 { > > + reg = <0x01>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x01>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@2 { > > + reg = <0x02>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x02>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@3 { > > + reg = <0x03>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x03>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@4 { > > + reg = <0x04>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x04>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@5 { > > + reg = <0x05>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x05>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@6 { > > + reg = <0x06>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x06>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@7 { > > + reg = <0x07>; > > + aspeed,target_pwm = <25000>; > > + cooling-levels = <125 151 177 203 229 255>; > > + aspeed,fan-tach-ch = <0x07>; > > + aspeed,min_rpm = <750000>; > > + }; > > + > > + fan@8 { > > + reg = <0x08>; > > + aspeed,fan-tach-ch = <0x08>; > > + }; > > + > > + fan@9 { > > + reg = <0x09>; > > + aspeed,fan-tach-ch = <0x09>; > > + }; > > + > > + fan@10 { > > + reg = <0x0a>; > > + aspeed,fan-tach-ch = <0x0a>; > > + }; > > + > > + fan@11 { > > + reg = <0x0b>; > > + aspeed,fan-tach-ch = <0x0b>; > > + }; > > + > > + fan@12 { > > + reg = <0x0c>; > > + aspeed,fan-tach-ch = <0x0c>; > > + }; > > + > > + fan@13 { > > + reg = <0x0d>; > > + aspeed,fan-tach-ch = <0x0d>; > > + }; > > + > > + fan@14 { > > + reg = <0x0e>; > > + aspeed,fan-tach-ch = <0x0e>; > > + }; > > + > > + fan@15 { > > + reg = <0x0f>; > > + aspeed,fan-tach-ch = <0x0f>; > > + }; > > + }; > > +}; > > + > > +&mdio0 { > > + status = "okay"; > > + > > + ethphy0: ethernet-phy@0 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + }; > > +}; > > + > > +&mac3 { > > + status = "okay"; > > + phy-mode = "rgmii"; > > + phy-handle = <ðphy0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_rgmii4_default>; > > +}; > > + > > +&fmc { > > + status = "okay"; > > + > > + flash@0 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bmc"; > > + spi-max-frequency = <33000000>; > > + spi-tx-bus-width = <2>; > > + spi-rx-bus-width = <2>; > > +#include "openbmc-flash-layout.dtsi" > > + }; > > + > > + flash@1 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bmc2"; > > + spi-max-frequency = <33000000>; > > + spi-tx-bus-width = <2>; > > + spi-rx-bus-width = <2>; > > + }; > > +}; > > + > > +&spi1 { > > + status = "okay"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_spi1_default>; > > + > > + flash@0 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bios"; > > + spi-max-frequency = <33000000>; > > + spi-tx-bus-width = <1>; > > + spi-rx-bus-width = <1>; > > + }; > > +}; > > + > > +&wdt1 { > > + status = "okay"; > > +}; > > + > > +&uart1 { > > + status = "okay"; > > +}; > > + > > +&uart5 { > > + status = "okay"; > > +}; > > + > > +&i2c0 { > > + status = "okay"; > > + > > + //Set bmc' slave address; > > + bmc_slave@10 { > > + compatible = "ipmb-dev"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + i2c-protocol; > > + }; > > +}; > > + > > +&i2c2 { > > + status = "okay"; > > +}; > > + > > +&i2c3 { > > + // FRU AT24C512C-SSHM-T > > + status = "okay"; > > + eeprom@50 { > > + compatible = "atmel,24c512"; > > + reg = <0x50>; > > + pagesize = <128>; > > + }; > > +}; > > + > > +&i2c5 { > > + status = "okay"; > > +}; > > + > > +&i2c6 { > > + status = "okay"; > > + > > + tmp75@49 { > > + compatible = "ti,tmp75"; > > + reg = <0x49>; > > + }; > > + > > + tmp75@4f { > > + compatible = "ti,tmp75"; > > + reg = <0x4f>; > > + }; > > + > > + tmp468@48 { > > + compatible = "ti,tmp468"; > > + reg = <0x48>; > > + }; > > +}; > > + > > +&i2c7 { > > + status = "okay"; > > + adm1278@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > + > > +&i2c8 { > > + // FRU AT24C512C-SSHM-T > > + status = "okay"; > > + > > + eeprom@51 { > > + compatible = "atmel,24c512"; > > + reg = <0x51>; > > + pagesize = <128>; > > + }; > > + > > + eeprom@53 { > > + compatible = "atmel,24c512"; > > + reg = <0x53>; > > + pagesize = <128>; > > + }; > > +}; > > + > > +&i2c9 { > > + // M.2 > > + status = "okay"; > > +}; > > + > > +&i2c10 { > > + // I2C EXPANDER > > + status = "okay"; > > + > > + i2c-switch@71 { > > + compatible = "nxp,pca9544"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x71>; > > + }; > > + > > + i2c-switch@73 { > > + compatible = "nxp,pca9544"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x73>; > > + }; > > +}; > > + > > +&i2c11 { > > + // I2C EXPANDER > > + status = "okay"; > > + > > + i2c-switch@70 { > > + compatible = "nxp,pca9544"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x70>; > > + > > + pcie_eeprom_riser1: i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0>; > > + > > + eeprom@55 { > > + compatible = "atmel,24c512"; > > + reg = <0x55>; > > + pagesize = <128>; > > + }; > > + }; > > + > > + pcie_eeprom_riser2: i2c@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <1>; > > + > > + eeprom@55 { > > + compatible = "atmel,24c512"; > > + reg = <0x55>; > > + pagesize = <128>; > > + }; > > + }; > > + > > + pcie_eeprom_riser3: i2c@2 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <2>; > > + > > + eeprom@55 { > > + compatible = "atmel,24c512"; > > + reg = <0x55>; > > + pagesize = <128>; > > + }; > > + }; > > + }; > > +}; > > + > > +&i2c12 { > > + status = "okay"; > > + > > + psu0:psu0@58 { > > + compatible = "pmbus"; > > + reg = <0x58>; > > + }; > > +}; > > + > > +&gpio0 { > > + status = "okay"; > > + gpio-line-names = > > + /*A0-A7*/ "","","","","","","","", > > + /*B0-B7*/ "presence-ps0","power-chassis-good","","","","","presence-ps1","", > > + /*C0-C7*/ "","","","","","","","", > > + /*D0-D7*/ "","","","","","","","", > > + /*E0-E7*/ "","","","","","","","", > > + /*F0-F7*/ "","","","","power-chassis-control","","","", > > + /*G0-G7*/ "","","jtag-mux","","","","","", > > + /*H0-H7*/ "","","","","reset-button","power-button","","", > > + /*I0-I7*/ "","","","","","","","", > > + /*J0-J7*/ "","","","","","","","", > > + /*K0-K7*/ "","","","","","","","", > > + /*L0-L7*/ "","","","","","","","", > > + /*M0-M7*/ "","","","","","","","", > > + /*N0-N7*/ "","","","","","","","", > > + /*O0-O7*/ "","","","","","","","", > > + /*P0-P7*/ "","","","tck-mux","","","","", > > + /*Q0-Q7*/ "","","","","","","","", > > + /*R0-R7*/ "","","","","","","","", > > + /*S0-S7*/ "","","","","","","","", > > + /*T0-T7*/ "","","","","","","","", > > + /*U0-U7*/ "","nmi-button","","","","","","", > > + /*V0-V7*/ "","","","","power-config-full-load","","","", > > + /*W0-W7*/ "","","","","","","","", > > + /*X0-X7*/ "","","","","","","","", > > + /*Y0-Y7*/ "","","","","","","","", > > + /*Z0-Z7*/ "","","","","","","","", > > + /*AA0-AA7*/ "","","","","","","","", > > + /*AB0-AB7*/ "","","","","","","","", > > + /*AC0-AC7*/ "","","","","","","",""; > > +}; > > + > > +&lpc_snoop { > > + status = "okay"; > > + snoop-ports = <0x80>; > > +}; > > + > > +&emmc_controller { > > + status = "okay"; > > +}; > > + > > +&emmc { > > + status = "okay"; > > + non-removable; > > + max-frequency = <52000000>; > > + bus-width = <8>; > > +}; > > + > > +&vhub { > > + status = "okay"; > > + aspeed,vhub-downstream-ports = <7>; > > + aspeed,vhub-generic-endpoints = <21>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usb2ad_default>; > > +}; > > + > > +&rtc { > > + status = "okay"; > > +}; > > -- > > 2.33.0 > > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC 2021-10-19 2:06 ` Lin.TommySC 林世欽 TAO @ 2021-10-19 2:10 ` Joel Stanley 0 siblings, 0 replies; 5+ messages in thread From: Joel Stanley @ 2021-10-19 2:10 UTC (permalink / raw) To: Lin.TommySC 林世欽 TAO Cc: Ye.Vic 葉宇清 TAO, openbmc, Mohammed.Habeeb ISV On Tue, 19 Oct 2021 at 02:06, Lin.TommySC 林世欽 TAO <Lin.TommySC@inventec.com> wrote: > > Hi Joel, > > Could you give some hint on how to upgrade to v5.15-rc1? I don't see this tag in upstream github https://github.com/openbmc/linux. You can find it in Linus' tree here: git clone https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git The latest commit is v5.15-rc6, which is fine to test with. Or you can check out v5.15-rc1 and apply your patch on top. Cheers, Joel ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-10-19 2:11 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <3a7fed78df06416da20ec72f14111c97@inventec.com>
2021-10-14 2:31 ` [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC Lin.TommySC 林世欽 TAO
2021-10-18 23:43 ` Joel Stanley
2021-10-18 23:48 ` Joel Stanley
2021-10-19 2:06 ` Lin.TommySC 林世欽 TAO
2021-10-19 2:10 ` Joel Stanley
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).