From: Marijn Suijten <marijn.suijten@somainline.org>
To: phone-devel@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: ~postmarketos/upstreaming@lists.sr.ht,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@somainline.org>,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Martin Botka <martin.botka@somainline.org>,
Jami Kettunen <jami.kettunen@somainline.org>,
Marijn Suijten <marijn.suijten@somainline.org>,
Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 7/7] arm64: dts: qcom: sm6125-seine: Configure additional trinket thermistors
Date: Thu, 12 May 2022 00:06:13 +0200 [thread overview]
Message-ID: <20220511220613.1015472-8-marijn.suijten@somainline.org> (raw)
In-Reply-To: <20220511220613.1015472-1-marijn.suijten@somainline.org>
In addition to PMIC-specific (pm6125) thermistors downstream extends
this set with the rf-pa0/rf-pa1, quiet, camera-flash and UFS/eMMC
thermistors in sm6125 (trinket) board and seine-specific DT files. All
thermistors report sensible temperature readings in userspace.
The sensors are also added to their respective Thermal Monitor node,
with thermal zones to match where applicable: emmc-ufs and camera-flash
are not available on the TM5 block, hence cannot be configured with a
tripping point and will not have a thermal zone.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
---
.../qcom/sm6125-sony-xperia-seine-pdx201.dts | 150 ++++++++++++++++++
1 file changed, 150 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
index c5967140d028..ca7f074a62a9 100644
--- a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
+++ b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
@@ -82,12 +82,162 @@ cmdline_mem: memory@ffd00000 {
no-map;
};
};
+
+ thermal-zones {
+ rf-pa0-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm6125_adc_tm 0>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ quiet-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <5000>;
+ thermal-sensors = <&pm6125_adc_tm 1>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ xo-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm6125_adc_tm 2>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ rf-pa1-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm6125_adc_tm 3>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+ };
};
&hsusb_phy1 {
status = "okay";
};
+&pm6125_adc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_flash_therm &emmc_ufs_therm &rf_pa1_therm>;
+
+ rf-pa0-therm@4d {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ quiet-therm@4e {
+ reg = <ADC5_AMUX_THM2_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ camera-flash-therm@52 {
+ reg = <ADC5_GPIO1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ emmc-ufs-therm@54 {
+ reg = <ADC5_GPIO3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ rf-pa1-therm@55 {
+ reg = <ADC5_GPIO4_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+};
+
+&pm6125_adc_tm {
+ status = "okay";
+
+ rf-pa0-therm@0 {
+ reg = <0>;
+ io-channels = <&pm6125_adc ADC5_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+
+ quiet-therm@1 {
+ reg = <1>;
+ io-channels = <&pm6125_adc ADC5_AMUX_THM2_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+
+ xo-therm@2 {
+ reg = <2>;
+ io-channels = <&pm6125_adc ADC5_XO_THERM_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+
+ rf-pa1-therm@3 {
+ reg = <3>;
+ io-channels = <&pm6125_adc ADC5_GPIO4_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+};
+
+&pm6125_gpio {
+ camera_flash_therm: camera-flash-therm {
+ pins = "gpio3";
+ function = "normal";
+ bias-high-impedance;
+ };
+
+ emmc_ufs_therm: emmc-ufs-therm {
+ pins = "gpio6";
+ function = "normal";
+ bias-high-impedance;
+ };
+
+ rf_pa1_therm: rf-pa1-therm {
+ pins = "gpio7";
+ function = "normal";
+ bias-high-impedance;
+ };
+};
+
&pon_pwrkey {
status = "okay";
};
--
2.36.1
next prev parent reply other threads:[~2022-05-11 22:06 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-11 22:06 [PATCH 0/7] Add Qcom PM6125 PMIC, and use in Sony Xperia Seine PDX201 Marijn Suijten
2022-05-11 22:06 ` [PATCH 1/7] arm64: dts: qcom: pm660: Use unique ADC5_VCOIN address in node name Marijn Suijten
2022-05-11 22:06 ` [PATCH 2/7] dt-bindings: pinctrl: qcom-pmic-gpio: Add pm6125 compatible Marijn Suijten
2022-05-13 8:19 ` Krzysztof Kozlowski
2022-05-13 9:17 ` Marijn Suijten
2022-05-13 9:37 ` Krzysztof Kozlowski
2022-05-13 21:09 ` Linus Walleij
2022-05-14 19:47 ` Krzysztof Kozlowski
2022-05-16 15:00 ` Bjorn Andersson
2022-05-19 12:51 ` Linus Walleij
2022-05-11 22:06 ` [PATCH 3/7] pinctrl: qcom: spmi-gpio: " Marijn Suijten
2022-05-16 15:00 ` Bjorn Andersson
2022-05-19 12:52 ` Linus Walleij
2022-05-11 22:06 ` [PATCH 4/7] iio: adc: qcom-spmi-adc5: Add missing VCOIN/AMUX_THM3/GPIO# channels Marijn Suijten
2022-05-14 16:13 ` Jonathan Cameron
2022-05-15 15:30 ` Marijn Suijten
2022-05-15 16:57 ` Jonathan Cameron
2022-05-15 16:58 ` Jonathan Cameron
2022-05-11 22:06 ` [PATCH 5/7] arm64: dts: qcom: Add PM6125 PMIC Marijn Suijten
2022-05-13 8:24 ` Krzysztof Kozlowski
2022-05-13 9:25 ` Marijn Suijten
2022-05-13 9:33 ` Krzysztof Kozlowski
2022-05-11 22:06 ` [PATCH 6/7] arm64: dts: qcom: sm6125-seine: Include PM6125 and configure PON Marijn Suijten
2022-05-11 22:06 ` Marijn Suijten [this message]
2022-05-13 8:25 ` [PATCH 7/7] arm64: dts: qcom: sm6125-seine: Configure additional trinket thermistors Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220511220613.1015472-8-marijn.suijten@somainline.org \
--to=marijn.suijten@somainline.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jami.kettunen@somainline.org \
--cc=konrad.dybcio@somainline.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.botka@somainline.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).