phone-devel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Alex Elder <elder@ieee.org>
To: Sireesh Kodali <sireeshkodali1@gmail.com>,
	phone-devel@vger.kernel.org,
	~postmarketos/upstreaming@lists.sr.ht, netdev@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	elder@kernel.org
Cc: "David S. Miller" <davem@davemloft.net>,
	Jakub Kicinski <kuba@kernel.org>
Subject: Re: [RFC PATCH 11/17] net: ipa: Add support for IPA v2.x endpoints
Date: Wed, 13 Oct 2021 17:30:20 -0500	[thread overview]
Message-ID: <3f6c17a8-b901-c64f-2fbb-48faabccd255@ieee.org> (raw)
In-Reply-To: <20210920030811.57273-12-sireeshkodali1@gmail.com>

On 9/19/21 10:08 PM, Sireesh Kodali wrote:
> IPA v2.x endpoints are the same as the endpoints on later versions. The
> only big change was the addition of the "skip_config" flag. The only
> other change is the backlog limit, which is a fixed number for IPA v2.6L

Not much to say here.  Your patches are reasonably small, which
makes them easier to review (thank you).

					-Alex

> Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
> ---
>   drivers/net/ipa/ipa_endpoint.c | 65 ++++++++++++++++++++++------------
>   1 file changed, 43 insertions(+), 22 deletions(-)
> 
> diff --git a/drivers/net/ipa/ipa_endpoint.c b/drivers/net/ipa/ipa_endpoint.c
> index 7d3ab61cd890..024cf3a0ded0 100644
> --- a/drivers/net/ipa/ipa_endpoint.c
> +++ b/drivers/net/ipa/ipa_endpoint.c
> @@ -360,8 +360,10 @@ void ipa_endpoint_modem_pause_all(struct ipa *ipa, bool enable)
>   {
>   	u32 endpoint_id;
>   
> -	/* DELAY mode doesn't work correctly on IPA v4.2 */
> -	if (ipa->version == IPA_VERSION_4_2)
> +	/* DELAY mode doesn't work correctly on IPA v4.2
> +	 * Pausing is not supported on IPA v2.6L
> +	 */
> +	if (ipa->version == IPA_VERSION_4_2 || ipa->version <= IPA_VERSION_2_6L)
>   		return;
>   
>   	for (endpoint_id = 0; endpoint_id < IPA_ENDPOINT_MAX; endpoint_id++) {
> @@ -383,6 +385,7 @@ int ipa_endpoint_modem_exception_reset_all(struct ipa *ipa)
>   {
>   	u32 initialized = ipa->initialized;
>   	struct ipa_trans *trans;
> +	u32 value = 0, value_mask = ~0;
>   	u32 count;
>   
>   	/* We need one command per modem TX endpoint.  We can get an upper
> @@ -398,6 +401,11 @@ int ipa_endpoint_modem_exception_reset_all(struct ipa *ipa)
>   		return -EBUSY;
>   	}
>   
> +	if (ipa->version <= IPA_VERSION_2_6L) {
> +		value = aggr_force_close_fmask(true);
> +		value_mask = aggr_force_close_fmask(true);
> +	}
> +
>   	while (initialized) {
>   		u32 endpoint_id = __ffs(initialized);
>   		struct ipa_endpoint *endpoint;
> @@ -416,7 +424,7 @@ int ipa_endpoint_modem_exception_reset_all(struct ipa *ipa)
>   		 * means status is disabled on the endpoint, and as a
>   		 * result all other fields in the register are ignored.
>   		 */
> -		ipa_cmd_register_write_add(trans, offset, 0, ~0, false);
> +		ipa_cmd_register_write_add(trans, offset, value, value_mask, false);
>   	}
>   
>   	ipa_cmd_pipeline_clear_add(trans);
> @@ -1531,8 +1539,10 @@ static void ipa_endpoint_program(struct ipa_endpoint *endpoint)
>   	ipa_endpoint_init_mode(endpoint);
>   	ipa_endpoint_init_aggr(endpoint);
>   	ipa_endpoint_init_deaggr(endpoint);
> -	ipa_endpoint_init_rsrc_grp(endpoint);
> -	ipa_endpoint_init_seq(endpoint);
> +	if (endpoint->ipa->version > IPA_VERSION_2_6L) {
> +		ipa_endpoint_init_rsrc_grp(endpoint);
> +		ipa_endpoint_init_seq(endpoint);
> +	}
>   	ipa_endpoint_status(endpoint);
>   }
>   
> @@ -1592,7 +1602,6 @@ void ipa_endpoint_suspend_one(struct ipa_endpoint *endpoint)
>   {
>   	struct device *dev = &endpoint->ipa->pdev->dev;
>   	struct ipa_dma *gsi = &endpoint->ipa->dma_subsys;
> -	bool stop_channel;
>   	int ret;
>   
>   	if (!(endpoint->ipa->enabled & BIT(endpoint->endpoint_id)))
> @@ -1613,7 +1622,6 @@ void ipa_endpoint_resume_one(struct ipa_endpoint *endpoint)
>   {
>   	struct device *dev = &endpoint->ipa->pdev->dev;
>   	struct ipa_dma *gsi = &endpoint->ipa->dma_subsys;
> -	bool start_channel;
>   	int ret;
>   
>   	if (!(endpoint->ipa->enabled & BIT(endpoint->endpoint_id)))
> @@ -1750,23 +1758,33 @@ int ipa_endpoint_config(struct ipa *ipa)
>   	/* Find out about the endpoints supplied by the hardware, and ensure
>   	 * the highest one doesn't exceed the number we support.
>   	 */
> -	val = ioread32(ipa->reg_virt + IPA_REG_FLAVOR_0_OFFSET);
> -
> -	/* Our RX is an IPA producer */
> -	rx_base = u32_get_bits(val, IPA_PROD_LOWEST_FMASK);
> -	max = rx_base + u32_get_bits(val, IPA_MAX_PROD_PIPES_FMASK);
> -	if (max > IPA_ENDPOINT_MAX) {
> -		dev_err(dev, "too many endpoints (%u > %u)\n",
> -			max, IPA_ENDPOINT_MAX);
> -		return -EINVAL;
> -	}
> -	rx_mask = GENMASK(max - 1, rx_base);
> +	if (ipa->version <= IPA_VERSION_2_6L) {
> +		// FIXME Not used anywhere?
> +		if (ipa->version == IPA_VERSION_2_6L)
> +			val = ioread32(ipa->reg_virt +
> +					IPA_REG_V2_ENABLED_PIPES_OFFSET);
> +		/* IPA v2.6L supports 20 pipes */
> +		ipa->available = ipa->filter_map;
> +		return 0;
> +	} else {
> +		val = ioread32(ipa->reg_virt + IPA_REG_FLAVOR_0_OFFSET);
> +
> +		/* Our RX is an IPA producer */
> +		rx_base = u32_get_bits(val, IPA_PROD_LOWEST_FMASK);
> +		max = rx_base + u32_get_bits(val, IPA_MAX_PROD_PIPES_FMASK);
> +		if (max > IPA_ENDPOINT_MAX) {
> +			dev_err(dev, "too many endpoints (%u > %u)\n",
> +					max, IPA_ENDPOINT_MAX);
> +			return -EINVAL;
> +		}
> +		rx_mask = GENMASK(max - 1, rx_base);
>   
> -	/* Our TX is an IPA consumer */
> -	max = u32_get_bits(val, IPA_MAX_CONS_PIPES_FMASK);
> -	tx_mask = GENMASK(max - 1, 0);
> +		/* Our TX is an IPA consumer */
> +		max = u32_get_bits(val, IPA_MAX_CONS_PIPES_FMASK);
> +		tx_mask = GENMASK(max - 1, 0);
>   
> -	ipa->available = rx_mask | tx_mask;
> +		ipa->available = rx_mask | tx_mask;
> +	}
>   
>   	/* Check for initialized endpoints not supported by the hardware */
>   	if (ipa->initialized & ~ipa->available) {
> @@ -1865,6 +1883,9 @@ u32 ipa_endpoint_init(struct ipa *ipa, u32 count,
>   			filter_map |= BIT(data->endpoint_id);
>   	}
>   
> +	if (ipa->version <= IPA_VERSION_2_6L)
> +		filter_map = 0x1fffff;
> +
>   	if (!ipa_filter_map_valid(ipa, filter_map))
>   		goto err_endpoint_exit;
>   
> 


  reply	other threads:[~2021-10-13 22:30 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-09-20  3:07 [RFC PATCH 00/17] net: ipa: Add support for IPA v2.x Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 01/17] net: ipa: Correct ipa_status_opcode enumeration Sireesh Kodali
2021-10-13 22:28   ` Alex Elder
2021-10-18 16:12     ` Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 02/17] net: ipa: revert to IPA_TABLE_ENTRY_SIZE for 32-bit IPA support Sireesh Kodali
2021-10-13 22:28   ` Alex Elder
2021-10-18 16:16     ` Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 04/17] net: ipa: Establish ipa_dma interface Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-10-18 16:45     ` Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 05/17] net: ipa: Check interrupts for availability Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 06/17] net: ipa: Add timeout for ipa_cmd_pipeline_clear_wait Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-10-18 17:02     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 07/17] net: ipa: Add IPA v2.x register definitions Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-10-18 17:25     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 08/17] net: ipa: Add support for IPA v2.x interrupts Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 09/17] net: ipa: Add support for using BAM as a DMA transport Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 17:30     ` Sireesh Kodali
2021-09-20  3:08 ` [PATCH 10/17] net: ipa: Add support for IPA v2.x commands and table init Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:13     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 11/17] net: ipa: Add support for IPA v2.x endpoints Sireesh Kodali
2021-10-13 22:30   ` Alex Elder [this message]
2021-10-18 18:17     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 12/17] net: ipa: Add support for IPA v2.x memory map Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:19     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 13/17] net: ipa: Add support for IPA v2.x in the driver's QMI interface Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:22     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 14/17] net: ipa: Add support for IPA v2 microcontroller Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 15/17] net: ipa: Add IPA v2.6L initialization sequence support Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 16/17] net: ipa: Add hw config describing IPA v2.x hardware Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:35     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 17/17] dt-bindings: net: qcom,ipa: Add support for MSM8953 and MSM8996 IPA Sireesh Kodali
2021-09-23 12:42   ` Rob Herring
2021-10-13 22:31   ` Alex Elder
2021-10-13 22:27 ` [RFC PATCH 00/17] net: ipa: Add support for IPA v2.x Alex Elder

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3f6c17a8-b901-c64f-2fbb-48faabccd255@ieee.org \
    --to=elder@ieee.org \
    --cc=davem@davemloft.net \
    --cc=elder@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=phone-devel@vger.kernel.org \
    --cc=sireeshkodali1@gmail.com \
    --cc=~postmarketos/upstreaming@lists.sr.ht \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).