phone-devel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: "Sireesh Kodali" <sireeshkodali1@gmail.com>
To: "Alex Elder" <elder@ieee.org>, <phone-devel@vger.kernel.org>,
	<~postmarketos/upstreaming@lists.sr.ht>, <netdev@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, <linux-arm-msm@vger.kernel.org>,
	<elder@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>,
	"Jakub Kicinski" <kuba@kernel.org>
Subject: Re: [RFC PATCH 11/17] net: ipa: Add support for IPA v2.x endpoints
Date: Mon, 18 Oct 2021 23:47:58 +0530	[thread overview]
Message-ID: <CF2QMSR815VC.5M3RMZULGVEV@skynet-linux> (raw)
In-Reply-To: <3f6c17a8-b901-c64f-2fbb-48faabccd255@ieee.org>

On Thu Oct 14, 2021 at 4:00 AM IST, Alex Elder wrote:
> On 9/19/21 10:08 PM, Sireesh Kodali wrote:
> > IPA v2.x endpoints are the same as the endpoints on later versions. The
> > only big change was the addition of the "skip_config" flag. The only
> > other change is the backlog limit, which is a fixed number for IPA v2.6L
>
> Not much to say here. Your patches are reasonably small, which
> makes them easier to review (thank you).
>
> -Alex

I'm glad splitting them up paid off!

Regards,
Sireesh
>
> > Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
> > ---
> >   drivers/net/ipa/ipa_endpoint.c | 65 ++++++++++++++++++++++------------
> >   1 file changed, 43 insertions(+), 22 deletions(-)
> > 
> > diff --git a/drivers/net/ipa/ipa_endpoint.c b/drivers/net/ipa/ipa_endpoint.c
> > index 7d3ab61cd890..024cf3a0ded0 100644
> > --- a/drivers/net/ipa/ipa_endpoint.c
> > +++ b/drivers/net/ipa/ipa_endpoint.c
> > @@ -360,8 +360,10 @@ void ipa_endpoint_modem_pause_all(struct ipa *ipa, bool enable)
> >   {
> >   	u32 endpoint_id;
> >   
> > -	/* DELAY mode doesn't work correctly on IPA v4.2 */
> > -	if (ipa->version == IPA_VERSION_4_2)
> > +	/* DELAY mode doesn't work correctly on IPA v4.2
> > +	 * Pausing is not supported on IPA v2.6L
> > +	 */
> > +	if (ipa->version == IPA_VERSION_4_2 || ipa->version <= IPA_VERSION_2_6L)
> >   		return;
> >   
> >   	for (endpoint_id = 0; endpoint_id < IPA_ENDPOINT_MAX; endpoint_id++) {
> > @@ -383,6 +385,7 @@ int ipa_endpoint_modem_exception_reset_all(struct ipa *ipa)
> >   {
> >   	u32 initialized = ipa->initialized;
> >   	struct ipa_trans *trans;
> > +	u32 value = 0, value_mask = ~0;
> >   	u32 count;
> >   
> >   	/* We need one command per modem TX endpoint.  We can get an upper
> > @@ -398,6 +401,11 @@ int ipa_endpoint_modem_exception_reset_all(struct ipa *ipa)
> >   		return -EBUSY;
> >   	}
> >   
> > +	if (ipa->version <= IPA_VERSION_2_6L) {
> > +		value = aggr_force_close_fmask(true);
> > +		value_mask = aggr_force_close_fmask(true);
> > +	}
> > +
> >   	while (initialized) {
> >   		u32 endpoint_id = __ffs(initialized);
> >   		struct ipa_endpoint *endpoint;
> > @@ -416,7 +424,7 @@ int ipa_endpoint_modem_exception_reset_all(struct ipa *ipa)
> >   		 * means status is disabled on the endpoint, and as a
> >   		 * result all other fields in the register are ignored.
> >   		 */
> > -		ipa_cmd_register_write_add(trans, offset, 0, ~0, false);
> > +		ipa_cmd_register_write_add(trans, offset, value, value_mask, false);
> >   	}
> >   
> >   	ipa_cmd_pipeline_clear_add(trans);
> > @@ -1531,8 +1539,10 @@ static void ipa_endpoint_program(struct ipa_endpoint *endpoint)
> >   	ipa_endpoint_init_mode(endpoint);
> >   	ipa_endpoint_init_aggr(endpoint);
> >   	ipa_endpoint_init_deaggr(endpoint);
> > -	ipa_endpoint_init_rsrc_grp(endpoint);
> > -	ipa_endpoint_init_seq(endpoint);
> > +	if (endpoint->ipa->version > IPA_VERSION_2_6L) {
> > +		ipa_endpoint_init_rsrc_grp(endpoint);
> > +		ipa_endpoint_init_seq(endpoint);
> > +	}
> >   	ipa_endpoint_status(endpoint);
> >   }
> >   
> > @@ -1592,7 +1602,6 @@ void ipa_endpoint_suspend_one(struct ipa_endpoint *endpoint)
> >   {
> >   	struct device *dev = &endpoint->ipa->pdev->dev;
> >   	struct ipa_dma *gsi = &endpoint->ipa->dma_subsys;
> > -	bool stop_channel;
> >   	int ret;
> >   
> >   	if (!(endpoint->ipa->enabled & BIT(endpoint->endpoint_id)))
> > @@ -1613,7 +1622,6 @@ void ipa_endpoint_resume_one(struct ipa_endpoint *endpoint)
> >   {
> >   	struct device *dev = &endpoint->ipa->pdev->dev;
> >   	struct ipa_dma *gsi = &endpoint->ipa->dma_subsys;
> > -	bool start_channel;
> >   	int ret;
> >   
> >   	if (!(endpoint->ipa->enabled & BIT(endpoint->endpoint_id)))
> > @@ -1750,23 +1758,33 @@ int ipa_endpoint_config(struct ipa *ipa)
> >   	/* Find out about the endpoints supplied by the hardware, and ensure
> >   	 * the highest one doesn't exceed the number we support.
> >   	 */
> > -	val = ioread32(ipa->reg_virt + IPA_REG_FLAVOR_0_OFFSET);
> > -
> > -	/* Our RX is an IPA producer */
> > -	rx_base = u32_get_bits(val, IPA_PROD_LOWEST_FMASK);
> > -	max = rx_base + u32_get_bits(val, IPA_MAX_PROD_PIPES_FMASK);
> > -	if (max > IPA_ENDPOINT_MAX) {
> > -		dev_err(dev, "too many endpoints (%u > %u)\n",
> > -			max, IPA_ENDPOINT_MAX);
> > -		return -EINVAL;
> > -	}
> > -	rx_mask = GENMASK(max - 1, rx_base);
> > +	if (ipa->version <= IPA_VERSION_2_6L) {
> > +		// FIXME Not used anywhere?
> > +		if (ipa->version == IPA_VERSION_2_6L)
> > +			val = ioread32(ipa->reg_virt +
> > +					IPA_REG_V2_ENABLED_PIPES_OFFSET);
> > +		/* IPA v2.6L supports 20 pipes */
> > +		ipa->available = ipa->filter_map;
> > +		return 0;
> > +	} else {
> > +		val = ioread32(ipa->reg_virt + IPA_REG_FLAVOR_0_OFFSET);
> > +
> > +		/* Our RX is an IPA producer */
> > +		rx_base = u32_get_bits(val, IPA_PROD_LOWEST_FMASK);
> > +		max = rx_base + u32_get_bits(val, IPA_MAX_PROD_PIPES_FMASK);
> > +		if (max > IPA_ENDPOINT_MAX) {
> > +			dev_err(dev, "too many endpoints (%u > %u)\n",
> > +					max, IPA_ENDPOINT_MAX);
> > +			return -EINVAL;
> > +		}
> > +		rx_mask = GENMASK(max - 1, rx_base);
> >   
> > -	/* Our TX is an IPA consumer */
> > -	max = u32_get_bits(val, IPA_MAX_CONS_PIPES_FMASK);
> > -	tx_mask = GENMASK(max - 1, 0);
> > +		/* Our TX is an IPA consumer */
> > +		max = u32_get_bits(val, IPA_MAX_CONS_PIPES_FMASK);
> > +		tx_mask = GENMASK(max - 1, 0);
> >   
> > -	ipa->available = rx_mask | tx_mask;
> > +		ipa->available = rx_mask | tx_mask;
> > +	}
> >   
> >   	/* Check for initialized endpoints not supported by the hardware */
> >   	if (ipa->initialized & ~ipa->available) {
> > @@ -1865,6 +1883,9 @@ u32 ipa_endpoint_init(struct ipa *ipa, u32 count,
> >   			filter_map |= BIT(data->endpoint_id);
> >   	}
> >   
> > +	if (ipa->version <= IPA_VERSION_2_6L)
> > +		filter_map = 0x1fffff;
> > +
> >   	if (!ipa_filter_map_valid(ipa, filter_map))
> >   		goto err_endpoint_exit;
> >   
> > 


  reply	other threads:[~2021-10-18 18:18 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-09-20  3:07 [RFC PATCH 00/17] net: ipa: Add support for IPA v2.x Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 01/17] net: ipa: Correct ipa_status_opcode enumeration Sireesh Kodali
2021-10-13 22:28   ` Alex Elder
2021-10-18 16:12     ` Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 02/17] net: ipa: revert to IPA_TABLE_ENTRY_SIZE for 32-bit IPA support Sireesh Kodali
2021-10-13 22:28   ` Alex Elder
2021-10-18 16:16     ` Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 04/17] net: ipa: Establish ipa_dma interface Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-10-18 16:45     ` Sireesh Kodali
2021-09-20  3:07 ` [RFC PATCH 05/17] net: ipa: Check interrupts for availability Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 06/17] net: ipa: Add timeout for ipa_cmd_pipeline_clear_wait Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-10-18 17:02     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 07/17] net: ipa: Add IPA v2.x register definitions Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-10-18 17:25     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 08/17] net: ipa: Add support for IPA v2.x interrupts Sireesh Kodali
2021-10-13 22:29   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 09/17] net: ipa: Add support for using BAM as a DMA transport Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 17:30     ` Sireesh Kodali
2021-09-20  3:08 ` [PATCH 10/17] net: ipa: Add support for IPA v2.x commands and table init Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:13     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 11/17] net: ipa: Add support for IPA v2.x endpoints Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:17     ` Sireesh Kodali [this message]
2021-09-20  3:08 ` [RFC PATCH 12/17] net: ipa: Add support for IPA v2.x memory map Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:19     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 13/17] net: ipa: Add support for IPA v2.x in the driver's QMI interface Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:22     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 14/17] net: ipa: Add support for IPA v2 microcontroller Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 15/17] net: ipa: Add IPA v2.6L initialization sequence support Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-09-20  3:08 ` [RFC PATCH 16/17] net: ipa: Add hw config describing IPA v2.x hardware Sireesh Kodali
2021-10-13 22:30   ` Alex Elder
2021-10-18 18:35     ` Sireesh Kodali
2021-09-20  3:08 ` [RFC PATCH 17/17] dt-bindings: net: qcom,ipa: Add support for MSM8953 and MSM8996 IPA Sireesh Kodali
2021-09-23 12:42   ` Rob Herring
2021-10-13 22:31   ` Alex Elder
2021-10-13 22:27 ` [RFC PATCH 00/17] net: ipa: Add support for IPA v2.x Alex Elder

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CF2QMSR815VC.5M3RMZULGVEV@skynet-linux \
    --to=sireeshkodali1@gmail.com \
    --cc=davem@davemloft.net \
    --cc=elder@ieee.org \
    --cc=elder@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=phone-devel@vger.kernel.org \
    --cc=~postmarketos/upstreaming@lists.sr.ht \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).