* [PATCH v2 00/10] update Facebook Bletchley BMC
@ 2022-02-14 4:25 Potin Lai
2022-02-14 4:25 ` [PATCH v2 01/10] arch: arm: dts: bletchley: switch sled numbering to 1-based Potin Lai
` (11 more replies)
0 siblings, 12 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
This patch series update Facebook Bletchley BMC devicetree base on EVT HW
schematioc design, and rebase SLED numbering to 1-based for OpenBMC
multi-host.
- GPIO:
- adding more gpio line names
- include interrupt line in io expander for gpio interrupt monitoring
- SPI flash:
- adding dual flash BSM module support
- switch to spi2-gpio on spi2 due to unstable signal issue
- Hwmon Sensors:
- adding INA230 sensors for monitoring
- fix ADM1278 shunt-resistor
- MDIO Bus: enable mido3 bus
- RTC: switch to external battery-backed rtc
- OpenBMC: 1-based SLED numbering
LINK: [v1] https://lore.kernel.org/all/20220211014347.24841-1-potin.lai@quantatw.com/
Changes v1 --> v2:
- update the details of new added gpio line names in commit message
- add battery-backed rtc information in comment and commit message
Potin Lai (10):
arch: arm: dts: bletchley: switch sled numbering to 1-based
arch: arm: dts: bletchley: separate leds into multiple groups
arch: arm: dts: bletchley: update gpio-line-names
arch: arm: dts: bletchley: update fmc configurations
arch: arm: dts: bletchley: switch to spi-gpio for spi2
arch: arm: dts: bletchley: add interrupt support for sled io expander
arch: arm: dts: bletchley: add shunt-resistor for ADM1278
arch: arm: dts: bletchley: add INA230 sensor on each sled
arch: arm: dts: bletchley: enable mdio3 bus
arch: arm: dts: bletchley: cleanup redundant nodes
.../dts/aspeed-bmc-facebook-bletchley.dts | 303 +++++++++++-------
1 file changed, 194 insertions(+), 109 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 01/10] arch: arm: dts: bletchley: switch sled numbering to 1-based
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 02/10] arch: arm: dts: bletchley: separate leds into multiple groups Potin Lai
` (10 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
Switch sled to 1-based to meet OpenBMC multi-host numbering rule
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
.../dts/aspeed-bmc-facebook-bletchley.dts | 128 +++++++++---------
1 file changed, 64 insertions(+), 64 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index f973ea883b97..e77736ed5c4c 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -101,16 +101,6 @@
default-state = "off";
gpios = <&fan_ioexp 15 GPIO_ACTIVE_HIGH>;
};
- sled0_amber {
- retain-state-shutdown;
- default-state = "off";
- gpios = <&sled0_leds 0 GPIO_ACTIVE_LOW>;
- };
- sled0_blue {
- retain-state-shutdown;
- default-state = "off";
- gpios = <&sled0_leds 1 GPIO_ACTIVE_LOW>;
- };
sled1_amber {
retain-state-shutdown;
default-state = "off";
@@ -161,6 +151,16 @@
default-state = "off";
gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
};
+ sled6_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled6_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
+ };
};
};
@@ -219,7 +219,7 @@
reg = <0x4f>;
};
- sled0_ioexp: pca9539@76 {
+ sled1_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -228,13 +228,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "SLED0_MS_DETECT1","SLED0_VBUS_BMC_EN","SLED0_INA230_ALERT","SLED0_P12V_STBY_ALERT",
- "SLED0_SSD_ALERT","SLED0_MS_DETECT0","SLED0_RST_CCG5","SLED0_FUSB302_INT",
- "SLED0_MD_STBY_RESET","SLED0_MD_IOEXP_EN_FAULT","SLED0_MD_DIR","SLED0_MD_DECAY",
- "SLED0_MD_MODE1","SLED0_MD_MODE2","SLED0_MD_MODE3","power-host0";
+ "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+ "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+ "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+ "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
};
- sled0_leds: pca9552@67 {
+ sled1_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -243,13 +243,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled0-amber","led-sled0-blue","SLED0_RST_IOEXP","",
+ "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
"","","","",
"","","","",
"","","","";
};
- sled0_fusb302: typec-portc@22 {
+ sled1_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -282,7 +282,7 @@
reg = <0x4f>;
};
- sled1_ioexp: pca9539@76 {
+ sled2_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -291,13 +291,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
- "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
- "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
- "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+ "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
+ "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
+ "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
+ "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
};
- sled1_leds: pca9552@67 {
+ sled2_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -306,13 +306,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
+ "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
"","","","",
"","","","",
"","","","";
};
- sled1_fusb302: typec-portc@22 {
+ sled2_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -349,7 +349,7 @@
reg = <0x4f>;
};
- sled2_ioexp: pca9539@76 {
+ sled3_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -358,13 +358,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
- "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
- "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
- "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
+ "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
+ "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
+ "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
+ "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
};
- sled2_leds: pca9552@67 {
+ sled3_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -373,13 +373,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
+ "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
"","","","",
"","","","",
"","","","";
};
- sled2_fusb302: typec-portc@22 {
+ sled3_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -412,7 +412,7 @@
reg = <0x4f>;
};
- sled3_ioexp: pca9539@76 {
+ sled4_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -421,13 +421,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
- "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
- "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
- "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
+ "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
+ "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
+ "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
+ "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
};
- sled3_leds: pca9552@67 {
+ sled4_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -436,13 +436,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
+ "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
"","","","",
"","","","",
"","","","";
};
- sled3_fusb302: typec-portc@22 {
+ sled4_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -475,7 +475,7 @@
reg = <0x4f>;
};
- sled4_ioexp: pca9539@76 {
+ sled5_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -484,13 +484,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
- "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
- "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
- "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
+ "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
+ "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
+ "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
+ "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
};
- sled4_leds: pca9552@67 {
+ sled5_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -499,13 +499,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
+ "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
"","","","",
"","","","",
"","","","";
};
- sled4_fusb302: typec-portc@22 {
+ sled5_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -538,7 +538,7 @@
reg = <0x4f>;
};
- sled5_ioexp: pca9539@76 {
+ sled6_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -547,13 +547,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
- "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
- "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
- "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
+ "SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
+ "SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
+ "SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
+ "SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
};
- sled5_leds: pca9552@67 {
+ sled6_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -562,13 +562,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
+ "led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","",
"","","","",
"","","","",
"","","","";
};
- sled5_fusb302: typec-portc@22 {
+ sled6_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -702,17 +702,17 @@
/*F0-F7*/ "","","","","","","","",
/*G0-G7*/ "","SWITCH_FRU_MUX","","","","","","",
/*H0-H7*/ "presence-riser1","presence-riser2",
- "presence-sled0","presence-sled1",
- "presence-sled2","presence-sled3",
- "presence-sled4","presence-sled5",
+ "presence-sled1","presence-sled2",
+ "presence-sled3","presence-sled4",
+ "presence-sled5","presence-sled6",
/*I0-I7*/ "REV_ID0","","REV_ID1","REV_ID2",
"","","","",
/*J0-J7*/ "","","","","","","","",
/*K0-K7*/ "","","","","","","","",
/*L0-L7*/ "","","","","","","","",
- /*M0-M7*/ "ALERT_SLED0","ALERT_SLED1",
- "ALERT_SLED2","ALERT_SLED3",
- "ALERT_SLED4","ALERT_SLED5",
+ /*M0-M7*/ "ALERT_SLED1","ALERT_SLED2",
+ "ALERT_SLED3","ALERT_SLED4",
+ "ALERT_SLED5","ALERT_SLED6",
"P12V_AUX_ALERT1","",
/*N0-N7*/ "","","","","","","","",
/*O0-O7*/ "","","","",
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 02/10] arch: arm: dts: bletchley: separate leds into multiple groups
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
2022-02-14 4:25 ` [PATCH v2 01/10] arch: arm: dts: bletchley: switch sled numbering to 1-based Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 03/10] arch: arm: dts: bletchley: update gpio-line-names Potin Lai
` (9 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
Separate gpio-leds by each io expander chip.
To avoid entire gpio-leds bind failed due to single chip not available
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
.../dts/aspeed-bmc-facebook-bletchley.dts | 77 +++++++++++++------
1 file changed, 52 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index e77736ed5c4c..ebd2430a3bdd 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -5,6 +5,7 @@
#include "aspeed-g6.dtsi"
#include <dt-bindings/gpio/aspeed-gpio.h>
#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
/ {
model = "Facebook Bletchley BMC";
@@ -53,112 +54,138 @@
// Fixed link
};
- leds {
+ front_gpio_leds {
compatible = "gpio-leds";
-
sys_log_id {
- retain-state-shutdown;
- default-state = "keep";
+ default-state = "off";
gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
};
+ };
+
+ fan_gpio_leds {
+ compatible = "gpio-leds";
fan0_blue {
retain-state-shutdown;
default-state = "on";
- gpios = <&fan_ioexp 8 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 8 GPIO_ACTIVE_HIGH>;
};
fan1_blue {
retain-state-shutdown;
default-state = "on";
- gpios = <&fan_ioexp 9 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 9 GPIO_ACTIVE_HIGH>;
};
fan2_blue {
retain-state-shutdown;
default-state = "on";
- gpios = <&fan_ioexp 10 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 10 GPIO_ACTIVE_HIGH>;
};
fan3_blue {
retain-state-shutdown;
default-state = "on";
- gpios = <&fan_ioexp 11 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 11 GPIO_ACTIVE_HIGH>;
};
fan0_amber {
retain-state-shutdown;
default-state = "off";
- gpios = <&fan_ioexp 12 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 12 GPIO_ACTIVE_HIGH>;
};
fan1_amber {
retain-state-shutdown;
default-state = "off";
- gpios = <&fan_ioexp 13 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 13 GPIO_ACTIVE_HIGH>;
};
fan2_amber {
retain-state-shutdown;
default-state = "off";
- gpios = <&fan_ioexp 14 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 14 GPIO_ACTIVE_HIGH>;
};
fan3_amber {
retain-state-shutdown;
default-state = "off";
- gpios = <&fan_ioexp 15 GPIO_ACTIVE_HIGH>;
+ gpios = <&fan_leds 15 GPIO_ACTIVE_HIGH>;
};
+ };
+
+ sled1_gpio_leds {
+ compatible = "gpio-leds";
sled1_amber {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
};
sled1_blue {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled2_gpio_leds {
+ compatible = "gpio-leds";
sled2_amber {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
};
sled2_blue {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled3_gpio_leds {
+ compatible = "gpio-leds";
sled3_amber {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
};
sled3_blue {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled4_gpio_leds {
+ compatible = "gpio-leds";
sled4_amber {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
};
sled4_blue {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled5_gpio_leds {
+ compatible = "gpio-leds";
sled5_amber {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
};
sled5_blue {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled6_gpio_leds {
+ compatible = "gpio-leds";
sled6_amber {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>;
};
sled6_blue {
retain-state-shutdown;
- default-state = "off";
+ default-state = "keep";
gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
};
};
@@ -667,7 +694,7 @@
reg = <0x4d>;
};
- fan_ioexp: pca9552@67 {
+ fan_leds: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 03/10] arch: arm: dts: bletchley: update gpio-line-names
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
2022-02-14 4:25 ` [PATCH v2 01/10] arch: arm: dts: bletchley: switch sled numbering to 1-based Potin Lai
2022-02-14 4:25 ` [PATCH v2 02/10] arch: arm: dts: bletchley: separate leds into multiple groups Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 04/10] arch: arm: dts: bletchley: update fmc configurations Potin Lai
` (8 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
update gpio-line-names based on EVT HW schematic
- gpio0:
- BSM_FRU_WP (G0, out)
- PWRGD_P1V05_VDDCORE (G4, in)
- PWRGD_P1V5_VDD (G5, in)
- BSM_FLASH_WP_STATUS (I5, in)
- BMC_TPM_PRES (I6, in)
- BMC_RTC_INT (L5, in)
- BMC_HEARTBEAT (P7, out)
- PWRGD_CNS_PSU (V0, in)
- PSU_PRSNT (V3, in)
- BMC_SELF_HW_RST (Y0, out)
- BSM_PRSNT (Y1, in)
- sled1_led pca9522:
- SLED1_MD_REF_PWM (3, out)
- sled2_led pca9522:
- SLED2_MD_REF_PWM (3, out)
- sled3_led pca9522:
- SLED3_MD_REF_PWM (3, out)
- sled4_led pca9522:
- SLED4_MD_REF_PWM (3, out)
- sled5_led pca9522:
- SLED5_MD_REF_PWM (3, out)
- sled6_led pca9522:
- SLED6_MD_REF_PWM (3, out)
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
.../dts/aspeed-bmc-facebook-bletchley.dts | 26 ++++++++++---------
1 file changed, 14 insertions(+), 12 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index ebd2430a3bdd..fc0690ccdb0a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -270,7 +270,7 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
+ "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
@@ -333,7 +333,7 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
+ "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
@@ -400,7 +400,7 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
+ "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
@@ -463,7 +463,7 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
+ "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
@@ -526,7 +526,7 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
+ "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
@@ -589,7 +589,7 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","",
+ "led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
@@ -727,16 +727,17 @@
/*D0-D7*/ "","","","","","","","",
/*E0-E7*/ "","","","","","","","",
/*F0-F7*/ "","","","","","","","",
- /*G0-G7*/ "","SWITCH_FRU_MUX","","","","","","",
+ /*G0-G7*/ "BSM_FRU_WP","SWITCH_FRU_MUX","","",
+ "PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
/*H0-H7*/ "presence-riser1","presence-riser2",
"presence-sled1","presence-sled2",
"presence-sled3","presence-sled4",
"presence-sled5","presence-sled6",
/*I0-I7*/ "REV_ID0","","REV_ID1","REV_ID2",
- "","","","",
+ "","BSM_FLASH_WP_STATUS","BMC_TPM_PRES","",
/*J0-J7*/ "","","","","","","","",
/*K0-K7*/ "","","","","","","","",
- /*L0-L7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","BMC_RTC_INT","","",
/*M0-M7*/ "ALERT_SLED1","ALERT_SLED2",
"ALERT_SLED3","ALERT_SLED4",
"ALERT_SLED5","ALERT_SLED6",
@@ -744,19 +745,20 @@
/*N0-N7*/ "","","","","","","","",
/*O0-O7*/ "","","","",
"","BOARD_ID0","BOARD_ID1","BOARD_ID2",
- /*P0-P7*/ "","","","","","","","",
+ /*P0-P7*/ "","","","","","","","BMC_HEARTBEAT",
/*Q0-Q7*/ "","","","","","","","",
/*R0-R7*/ "","","","","","","","",
/*S0-S7*/ "","","","BAT_DETECT",
"BMC_BT_WP0","BMC_BT_WP1","","",
/*T0-T7*/ "","","","","","","","",
/*U0-U7*/ "","","","","","","","",
- /*V0-V7*/ "","RST_BMC_MVL","","",
+ /*V0-V7*/ "PWRGD_CNS_PSU","RST_BMC_MVL","","PSU_PRSNT",
"USB2_SEL0_A","USB2_SEL1_A",
"USB2_SEL0_B","USB2_SEL1_B",
/*W0-W7*/ "RST_FRONT_IOEXP","","","","","","","",
/*X0-X7*/ "","","","","","","","",
- /*Y0-Y7*/ "","","BSM_FLASH_LATCH","","","","","",
+ /*Y0-Y7*/ "BMC_SELF_HW_RST","BSM_PRSNT","BSM_FLASH_LATCH","",
+ "","","","",
/*Z0-Z7*/ "","","","","","","","";
};
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 04/10] arch: arm: dts: bletchley: update fmc configurations
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (2 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 03/10] arch: arm: dts: bletchley: update gpio-line-names Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 05/10] arch: arm: dts: bletchley: switch to spi-gpio for spi2 Potin Lai
` (7 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
add flash1 in fmc to support dual flash module
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index fc0690ccdb0a..b01f1e7adb81 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -217,6 +217,12 @@
spi-max-frequency = <50000000>;
#include "openbmc-flash-layout-128.dtsi"
};
+ flash@1 {
+ status = "okay";
+ m25p,fast-read;
+ label = "flash1";
+ spi-max-frequency = <50000000>;
+ };
};
&spi2 {
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 05/10] arch: arm: dts: bletchley: switch to spi-gpio for spi2
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (3 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 04/10] arch: arm: dts: bletchley: update fmc configurations Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-15 5:48 ` Joel Stanley
2022-02-14 4:25 ` [PATCH v2 06/10] arch: arm: dts: bletchley: add interrupt support for sled io expander Potin Lai
` (6 subsequent siblings)
11 siblings, 1 reply; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
Switch to spi-gpio driver to avoid unstable signal issue with EVT HW
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index b01f1e7adb81..3c54e4a892c9 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -227,8 +227,16 @@
&spi2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_spi2_default>;
+
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
flash@0 {
status = "okay";
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 06/10] arch: arm: dts: bletchley: add interrupt support for sled io expander
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (4 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 05/10] arch: arm: dts: bletchley: switch to spi-gpio for spi2 Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 07/10] arch: arm: dts: bletchley: add shunt-resistor for ADM1278 Potin Lai
` (5 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
Enable interrupt support for all sledx_ioexp, so userspace can monitor
gpio from io expander by interrupt
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
.../dts/aspeed-bmc-facebook-bletchley.dts | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index 3c54e4a892c9..8afaa8f52c38 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -6,6 +6,7 @@
#include <dt-bindings/gpio/aspeed-gpio.h>
#include <dt-bindings/usb/pd.h>
#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Facebook Bletchley BMC";
@@ -268,6 +269,9 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
+
gpio-line-names =
"SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
"SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
@@ -331,6 +335,9 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>;
+
gpio-line-names =
"SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
"SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
@@ -398,6 +405,9 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>;
+
gpio-line-names =
"SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
"SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
@@ -461,6 +471,9 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>;
+
gpio-line-names =
"SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
"SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
@@ -524,6 +537,9 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>;
+
gpio-line-names =
"SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
"SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
@@ -587,6 +603,9 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
+
gpio-line-names =
"SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
"SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 07/10] arch: arm: dts: bletchley: add shunt-resistor for ADM1278
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (5 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 06/10] arch: arm: dts: bletchley: add interrupt support for sled io expander Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 08/10] arch: arm: dts: bletchley: add INA230 sensor on each sled Potin Lai
` (4 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
fix with correct shunt-resistor value base on EVT HW
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index 8afaa8f52c38..76c086ea7b71 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -715,6 +715,7 @@
adm1278@11 {
compatible = "adi,adm1278";
reg = <0x11>;
+ shunt-resistor-micro-ohms = <300>;
};
tmp421@4c {
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 08/10] arch: arm: dts: bletchley: add INA230 sensor on each sled
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (6 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 07/10] arch: arm: dts: bletchley: add shunt-resistor for ADM1278 Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 09/10] arch: arm: dts: bletchley: enable mdio3 bus Potin Lai
` (3 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
add INA230 node on each sled base on EVT HW
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
.../dts/aspeed-bmc-facebook-bletchley.dts | 36 +++++++++++++++----
1 file changed, 30 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index 76c086ea7b71..8c8fbfcbb257 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -249,7 +249,11 @@
&i2c0 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -315,7 +319,11 @@
&i2c1 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -385,7 +393,11 @@
&i2c2 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -451,7 +463,11 @@
&i2c3 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -517,7 +533,11 @@
&i2c4 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -583,7 +603,11 @@
&i2c5 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 09/10] arch: arm: dts: bletchley: enable mdio3 bus
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (7 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 08/10] arch: arm: dts: bletchley: add INA230 sensor on each sled Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 4:25 ` [PATCH v2 10/10] arch: arm: dts: bletchley: cleanup redundant nodes Potin Lai
` (2 subsequent siblings)
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
Enable mdio3 bus based on EVT HW
So far lack of c45 support in mdio-aspeed, at least can access mdio bus
by read/write register
TODO: Add Marvell PHY 88X3310 and mdio-aspeed driver c45 support
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index 8c8fbfcbb257..946107bd8bc7 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -841,3 +841,8 @@
&pinctrl_adc12_default &pinctrl_adc13_default
&pinctrl_adc14_default &pinctrl_adc15_default>;
};
+
+&mdio3 {
+ status = "okay";
+ /* TODO: Add Marvell 88X3310 */
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 10/10] arch: arm: dts: bletchley: cleanup redundant nodes
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (8 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 09/10] arch: arm: dts: bletchley: enable mdio3 bus Potin Lai
@ 2022-02-14 4:25 ` Potin Lai
2022-02-14 18:27 ` [PATCH v2 00/10] update Facebook Bletchley BMC Patrick Williams
2022-02-15 5:51 ` Joel Stanley
11 siblings, 0 replies; 14+ messages in thread
From: Potin Lai @ 2022-02-14 4:25 UTC (permalink / raw)
To: Rob Herring, Joel Stanley, Andrew Jeffery
Cc: Patrick Williams, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, Potin Lai
cleanup following nodes
1. Remove redundant i2c1 node.
2. Disable in-chip rtc, use battery-backed external rtc (pcf85263)
instead.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
---
arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts | 9 +--------
1 file changed, 1 insertion(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index 946107bd8bc7..52201c6a69bc 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -205,10 +205,6 @@
};
};
-&rtc {
- status = "okay";
-};
-
&fmc {
status = "okay";
flash@0 {
@@ -387,10 +383,6 @@
};
};
-&i2c1 {
- status = "okay";
-};
-
&i2c2 {
status = "okay";
ina230@45 {
@@ -680,6 +672,7 @@
};
rtc@51 {
+ /* in-chip rtc disabled, use external rtc (battery-backed) */
compatible = "nxp,pcf85263";
reg = <0x51>;
};
--
2.17.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v2 00/10] update Facebook Bletchley BMC
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (9 preceding siblings ...)
2022-02-14 4:25 ` [PATCH v2 10/10] arch: arm: dts: bletchley: cleanup redundant nodes Potin Lai
@ 2022-02-14 18:27 ` Patrick Williams
2022-02-15 5:51 ` Joel Stanley
11 siblings, 0 replies; 14+ messages in thread
From: Patrick Williams @ 2022-02-14 18:27 UTC (permalink / raw)
To: Potin Lai
Cc: Rob Herring, Joel Stanley, Andrew Jeffery, devicetree,
linux-arm-kernel, linux-aspeed, linux-kernel
On Mon, Feb 14, 2022 at 12:25:28PM +0800, Potin Lai wrote:
> This patch series update Facebook Bletchley BMC devicetree base on EVT HW
> schematioc design, and rebase SLED numbering to 1-based for OpenBMC
> multi-host.
>
> - GPIO:
> - adding more gpio line names
> - include interrupt line in io expander for gpio interrupt monitoring
>
> - SPI flash:
> - adding dual flash BSM module support
> - switch to spi2-gpio on spi2 due to unstable signal issue
>
> - Hwmon Sensors:
> - adding INA230 sensors for monitoring
> - fix ADM1278 shunt-resistor
>
> - MDIO Bus: enable mido3 bus
>
> - RTC: switch to external battery-backed rtc
>
> - OpenBMC: 1-based SLED numbering
>
>
> LINK: [v1] https://lore.kernel.org/all/20220211014347.24841-1-potin.lai@quantatw.com/
>
>
> Changes v1 --> v2:
> - update the details of new added gpio line names in commit message
> - add battery-backed rtc information in comment and commit message
Thank you for the details there Potin.
>
> Potin Lai (10):
> arch: arm: dts: bletchley: switch sled numbering to 1-based
> arch: arm: dts: bletchley: separate leds into multiple groups
> arch: arm: dts: bletchley: update gpio-line-names
> arch: arm: dts: bletchley: update fmc configurations
> arch: arm: dts: bletchley: switch to spi-gpio for spi2
> arch: arm: dts: bletchley: add interrupt support for sled io expander
> arch: arm: dts: bletchley: add shunt-resistor for ADM1278
> arch: arm: dts: bletchley: add INA230 sensor on each sled
> arch: arm: dts: bletchley: enable mdio3 bus
> arch: arm: dts: bletchley: cleanup redundant nodes
>
> .../dts/aspeed-bmc-facebook-bletchley.dts | 303 +++++++++++-------
> 1 file changed, 194 insertions(+), 109 deletions(-)
>
> --
> 2.17.1
>
Entire series is
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
--
Patrick Williams
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 05/10] arch: arm: dts: bletchley: switch to spi-gpio for spi2
2022-02-14 4:25 ` [PATCH v2 05/10] arch: arm: dts: bletchley: switch to spi-gpio for spi2 Potin Lai
@ 2022-02-15 5:48 ` Joel Stanley
0 siblings, 0 replies; 14+ messages in thread
From: Joel Stanley @ 2022-02-15 5:48 UTC (permalink / raw)
To: Potin Lai
Cc: Rob Herring, Andrew Jeffery, Patrick Williams, devicetree,
Linux ARM, linux-aspeed, Linux Kernel Mailing List
On Mon, 14 Feb 2022 at 04:26, Potin Lai <potin.lai@quantatw.com> wrote:
>
> Switch to spi-gpio driver to avoid unstable signal issue with EVT HW
>
> Signed-off-by: Potin Lai <potin.lai@quantatw.com>
> ---
> arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts | 12 ++++++++++--
> 1 file changed, 10 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> index b01f1e7adb81..3c54e4a892c9 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> @@ -227,8 +227,16 @@
>
> &spi2 {
> status = "okay";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_spi2_default>;
> +
> + compatible = "spi-gpio";
This is a bit strange. You're effectively rewriting the node with a new one.
It would make more sense to leave spi2 disabled (the default), and add
a new node:
spi {
compatible = "spi-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
num-chipselects = <1>;
cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
flash@0 {
status = "okay";
etc.
Your new spi node doesn't need the pinctrl or clock properties.
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
> + gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
> + gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
> + num-chipselects = <1>;
> + cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
>
> flash@0 {
> status = "okay";
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 00/10] update Facebook Bletchley BMC
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
` (10 preceding siblings ...)
2022-02-14 18:27 ` [PATCH v2 00/10] update Facebook Bletchley BMC Patrick Williams
@ 2022-02-15 5:51 ` Joel Stanley
11 siblings, 0 replies; 14+ messages in thread
From: Joel Stanley @ 2022-02-15 5:51 UTC (permalink / raw)
To: Potin Lai
Cc: Rob Herring, Andrew Jeffery, Patrick Williams, devicetree,
Linux ARM, linux-aspeed, Linux Kernel Mailing List
On Mon, 14 Feb 2022 at 04:26, Potin Lai <potin.lai@quantatw.com> wrote:
>
> This patch series update Facebook Bletchley BMC devicetree base on EVT HW
> schematioc design, and rebase SLED numbering to 1-based for OpenBMC
> multi-host.
>
> - GPIO:
> - adding more gpio line names
> - include interrupt line in io expander for gpio interrupt monitoring
>
> - SPI flash:
> - adding dual flash BSM module support
> - switch to spi2-gpio on spi2 due to unstable signal issue
>
> - Hwmon Sensors:
> - adding INA230 sensors for monitoring
> - fix ADM1278 shunt-resistor
>
> - MDIO Bus: enable mido3 bus
>
> - RTC: switch to external battery-backed rtc
>
> - OpenBMC: 1-based SLED numbering
>
>
> LINK: [v1] https://lore.kernel.org/all/20220211014347.24841-1-potin.lai@quantatw.com/
>
>
> Changes v1 --> v2:
> - update the details of new added gpio line names in commit message
> - add battery-backed rtc information in comment and commit message
Looks good. I made some comments on the spi2 patch, please fix those
up and I will merge.
Note that the convention for patch names is:
ARM: dts: aspeed: bletchley: Description with sentence case
If you could update your patches to follow that it would be appreciated.
There's no need to re-send your series for the openbmc tree; I can
merge those once we've reviewed the ones for mainline.
Cheers,
Joel
>
> Potin Lai (10):
> arch: arm: dts: bletchley: switch sled numbering to 1-based
> arch: arm: dts: bletchley: separate leds into multiple groups
> arch: arm: dts: bletchley: update gpio-line-names
> arch: arm: dts: bletchley: update fmc configurations
> arch: arm: dts: bletchley: switch to spi-gpio for spi2
> arch: arm: dts: bletchley: add interrupt support for sled io expander
> arch: arm: dts: bletchley: add shunt-resistor for ADM1278
> arch: arm: dts: bletchley: add INA230 sensor on each sled
> arch: arm: dts: bletchley: enable mdio3 bus
> arch: arm: dts: bletchley: cleanup redundant nodes
>
> .../dts/aspeed-bmc-facebook-bletchley.dts | 303 +++++++++++-------
> 1 file changed, 194 insertions(+), 109 deletions(-)
>
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2022-02-15 5:51 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-02-14 4:25 [PATCH v2 00/10] update Facebook Bletchley BMC Potin Lai
2022-02-14 4:25 ` [PATCH v2 01/10] arch: arm: dts: bletchley: switch sled numbering to 1-based Potin Lai
2022-02-14 4:25 ` [PATCH v2 02/10] arch: arm: dts: bletchley: separate leds into multiple groups Potin Lai
2022-02-14 4:25 ` [PATCH v2 03/10] arch: arm: dts: bletchley: update gpio-line-names Potin Lai
2022-02-14 4:25 ` [PATCH v2 04/10] arch: arm: dts: bletchley: update fmc configurations Potin Lai
2022-02-14 4:25 ` [PATCH v2 05/10] arch: arm: dts: bletchley: switch to spi-gpio for spi2 Potin Lai
2022-02-15 5:48 ` Joel Stanley
2022-02-14 4:25 ` [PATCH v2 06/10] arch: arm: dts: bletchley: add interrupt support for sled io expander Potin Lai
2022-02-14 4:25 ` [PATCH v2 07/10] arch: arm: dts: bletchley: add shunt-resistor for ADM1278 Potin Lai
2022-02-14 4:25 ` [PATCH v2 08/10] arch: arm: dts: bletchley: add INA230 sensor on each sled Potin Lai
2022-02-14 4:25 ` [PATCH v2 09/10] arch: arm: dts: bletchley: enable mdio3 bus Potin Lai
2022-02-14 4:25 ` [PATCH v2 10/10] arch: arm: dts: bletchley: cleanup redundant nodes Potin Lai
2022-02-14 18:27 ` [PATCH v2 00/10] update Facebook Bletchley BMC Patrick Williams
2022-02-15 5:51 ` Joel Stanley
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).