From: Masahiro Yamada <yamada.m@jp.panasonic.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 14/26] mpc8260: remove sacsng board support
Date: Mon, 15 Dec 2014 23:26:19 +0900 [thread overview]
Message-ID: <1418653608-14177-15-git-send-email-yamada.m@jp.panasonic.com> (raw)
In-Reply-To: <1418653608-14177-1-git-send-email-yamada.m@jp.panasonic.com>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
---
arch/powerpc/cpu/mpc8260/Kconfig | 4 -
board/sacsng/Kconfig | 9 -
board/sacsng/MAINTAINERS | 6 -
board/sacsng/Makefile | 8 -
board/sacsng/clkinit.c | 1009 ------------------------------------
board/sacsng/clkinit.h | 103 ----
board/sacsng/flash.c | 507 -------------------
board/sacsng/ioconfig.h | 217 --------
board/sacsng/sacsng.c | 848 -------------------------------
configs/sacsng_defconfig | 3 -
doc/README.scrapyard | 1 +
include/configs/sacsng.h | 1038 --------------------------------------
12 files changed, 1 insertion(+), 3752 deletions(-)
delete mode 100644 board/sacsng/Kconfig
delete mode 100644 board/sacsng/MAINTAINERS
delete mode 100644 board/sacsng/Makefile
delete mode 100644 board/sacsng/clkinit.c
delete mode 100644 board/sacsng/clkinit.h
delete mode 100644 board/sacsng/flash.c
delete mode 100644 board/sacsng/ioconfig.h
delete mode 100644 board/sacsng/sacsng.c
delete mode 100644 configs/sacsng_defconfig
delete mode 100644 include/configs/sacsng.h
diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig
index 17e303d..bdaf126 100644
--- a/arch/powerpc/cpu/mpc8260/Kconfig
+++ b/arch/powerpc/cpu/mpc8260/Kconfig
@@ -40,9 +40,6 @@ config TARGET_PM828
config TARGET_PPMC8260
bool "Support ppmc8260"
-config TARGET_SACSNG
- bool "Support sacsng"
-
config TARGET_MPC8266ADS
bool "Support MPC8266ADS"
@@ -68,6 +65,5 @@ source "board/muas3001/Kconfig"
source "board/pm826/Kconfig"
source "board/pm828/Kconfig"
source "board/ppmc8260/Kconfig"
-source "board/sacsng/Kconfig"
endmenu
diff --git a/board/sacsng/Kconfig b/board/sacsng/Kconfig
deleted file mode 100644
index 1646425..0000000
--- a/board/sacsng/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_SACSNG
-
-config SYS_BOARD
- default "sacsng"
-
-config SYS_CONFIG_NAME
- default "sacsng"
-
-endif
diff --git a/board/sacsng/MAINTAINERS b/board/sacsng/MAINTAINERS
deleted file mode 100644
index b76e462..0000000
--- a/board/sacsng/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-SACSNG BOARD
-#M: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
-S: Orphan (since 2014-06)
-F: board/sacsng/
-F: include/configs/sacsng.h
-F: configs/sacsng_defconfig
diff --git a/board/sacsng/Makefile b/board/sacsng/Makefile
deleted file mode 100644
index 95e6b8d..0000000
--- a/board/sacsng/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := sacsng.o flash.o clkinit.o
diff --git a/board/sacsng/clkinit.c b/board/sacsng/clkinit.c
deleted file mode 100644
index 2a28037..0000000
--- a/board/sacsng/clkinit.c
+++ /dev/null
@@ -1,1009 +0,0 @@
-/*
- * (C) Copyright 2002
- * Custom IDEAS, Inc. <www.cideas.com>
- * Jon Diekema <diekema@cideas.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <asm/cpm_8260.h>
-#include <configs/sacsng.h>
-
-#include "clkinit.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int Daq64xSampling = 0;
-
-
-void Daq_BRG_Reset(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- volatile uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
-
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
- *brg_ptr |= CPM_BRG_RST;
- *brg_ptr &= ~CPM_BRG_RST;
-}
-
-void Daq_BRG_Disable(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- volatile uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
-
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
- *brg_ptr &= ~CPM_BRG_EN;
-}
-
-void Daq_BRG_Enable(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- volatile uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
- *brg_ptr |= CPM_BRG_EN;
-}
-
-uint Daq_BRG_Get_Div16(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
-
- if (*brg_ptr & CPM_BRG_DIV16) {
- /* DIV16 active */
- return true;
- }
- else {
- /* DIV16 inactive */
- return false;
- }
-}
-
-void Daq_BRG_Set_Div16(uint brg, uint div16)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
-
- if (div16) {
- /* DIV16 active */
- *brg_ptr |= CPM_BRG_DIV16;
- }
- else {
- /* DIV16 inactive */
- *brg_ptr &= ~CPM_BRG_DIV16;
- }
-}
-
-uint Daq_BRG_Get_Count(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
- uint brg_cnt;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
-
- /* Get the clock divider
- *
- * Note: A clock divider of 0 means divide by 1,
- * therefore we need to add 1 to the count.
- */
- brg_cnt = (*brg_ptr & CPM_BRG_CD_MASK) >> CPM_BRG_DIV16_SHIFT;
- brg_cnt++;
- if (*brg_ptr & CPM_BRG_DIV16) {
- brg_cnt *= 16;
- }
-
- return (brg_cnt);
-}
-
-void Daq_BRG_Set_Count(uint brg, uint brg_cnt)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
-
- /*
- * Note: A clock divider of 0 means divide by 1,
- * therefore we need to subtract 1 from the count.
- */
- if (brg_cnt > 4096) {
- /* Prescale = Divide by 16 */
- *brg_ptr = (*brg_ptr & ~CPM_BRG_CD_MASK) |
- (((brg_cnt / 16) - 1) << CPM_BRG_DIV16_SHIFT);
- *brg_ptr |= CPM_BRG_DIV16;
- }
- else {
- /* Prescale = Divide by 1 */
- *brg_ptr = (*brg_ptr & ~CPM_BRG_CD_MASK) |
- ((brg_cnt - 1) << CPM_BRG_DIV16_SHIFT);
- *brg_ptr &= ~CPM_BRG_DIV16;
- }
-}
-
-uint Daq_BRG_Get_ExtClk(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
-
- return ((*brg_ptr & CPM_BRG_EXTC_MASK) >> CPM_BRG_EXTC_SHIFT);
-}
-
-char* Daq_BRG_Get_ExtClk_Description(uint brg)
-{
- uint extc;
-
- extc = Daq_BRG_Get_ExtClk(brg);
-
- switch (brg + 1) {
- case 1:
- case 2:
- case 5:
- case 6: {
- switch (extc) {
- case 0: {
- return ("BRG_INT");
- }
- case 1: {
- return ("CLK3");
- }
- case 2: {
- return ("CLK5");
- }
- }
- return ("??1245??");
- }
- case 3:
- case 4:
- case 7:
- case 8: {
- switch (extc) {
- case 0: {
- return ("BRG_INT");
- }
- case 1: {
- return ("CLK9");
- }
- case 2: {
- return ("CLK15");
- }
- }
- return ("??3478??");
- }
- }
- return ("??9876??");
-}
-
-void Daq_BRG_Set_ExtClk(uint brg, uint extc)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg -= 4;
- }
- brg_ptr += brg;
-
- *brg_ptr = (*brg_ptr & ~CPM_BRG_EXTC_MASK) |
- ((extc << CPM_BRG_EXTC_SHIFT) & CPM_BRG_EXTC_MASK);
-}
-
-uint Daq_BRG_Rate(uint brg)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint *brg_ptr;
- uint brg_cnt;
- uint brg_freq = 0;
-
- brg_ptr = (uint *)&immr->im_brgc1;
- brg_ptr += brg;
- if (brg >= 5) {
- brg_ptr = (uint *)&immr->im_brgc5;
- brg_ptr += (brg - 4);
- }
-
- brg_cnt = Daq_BRG_Get_Count(brg);
-
- switch (Daq_BRG_Get_ExtClk(brg)) {
- case CPM_BRG_EXTC_CLK3:
- case CPM_BRG_EXTC_CLK5: {
- brg_freq = brg_cnt;
- break;
- }
- default: {
- brg_freq = (uint)BRG_INT_CLK / brg_cnt;
- }
- }
- return (brg_freq);
-}
-
-uint Daq_Get_SampleRate(void)
-{
- /*
- * Read the BRG's to return the actual sample rate.
- */
- return (Daq_BRG_Rate(MCLK_BRG) / (MCLK_DIVISOR * SCLK_DIVISOR));
-}
-
-void Daq_Init_Clocks(int sample_rate, int sample_64x)
-{
- volatile ioport_t *iopa = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 0 /* port A */);
- uint mclk_divisor; /* MCLK divisor */
- int flag; /* Interrupt state */
-
- /* Save off the clocking data */
- Daq64xSampling = sample_64x;
-
- /*
- * Limit the sample rate to some sensible values.
- */
- if (sample_rate > MAX_64x_SAMPLE_RATE) {
- sample_rate = MAX_64x_SAMPLE_RATE;
- }
- if (sample_rate < MIN_SAMPLE_RATE) {
- sample_rate = MIN_SAMPLE_RATE;
- }
-
- /*
- * Initialize the MCLK/SCLK/LRCLK baud rate generators.
- */
-
- /* Setup MCLK */
- Daq_BRG_Set_ExtClk(MCLK_BRG, CPM_BRG_EXTC_BRGCLK);
-
- /* Setup SCLK */
-# ifdef RUN_SCLK_ON_BRG_INT
- Daq_BRG_Set_ExtClk(SCLK_BRG, CPM_BRG_EXTC_BRGCLK);
-# else
- Daq_BRG_Set_ExtClk(SCLK_BRG, CPM_BRG_EXTC_CLK9);
-# endif
-
- /* Setup LRCLK */
-# ifdef RUN_LRCLK_ON_BRG_INT
- Daq_BRG_Set_ExtClk(LRCLK_BRG, CPM_BRG_EXTC_BRGCLK);
-# else
- Daq_BRG_Set_ExtClk(LRCLK_BRG, CPM_BRG_EXTC_CLK5);
-# endif
-
- /*
- * Dynamically adjust MCLK based on the new sample rate.
- */
-
- /* Compute the divisors */
- mclk_divisor = BRG_INT_CLK / (sample_rate * MCLK_DIVISOR * SCLK_DIVISOR);
-
- /*
- * Disable interrupt and save the current state
- */
- flag = disable_interrupts();
-
- /* Setup MCLK */
- Daq_BRG_Set_Count(MCLK_BRG, mclk_divisor);
-
- /* Setup SCLK */
-# ifdef RUN_SCLK_ON_BRG_INT
- Daq_BRG_Set_Count(SCLK_BRG, mclk_divisor * MCLK_DIVISOR);
-# else
- Daq_BRG_Set_Count(SCLK_BRG, MCLK_DIVISOR);
-# endif
-
-# ifdef RUN_LRCLK_ON_BRG_INT
- Daq_BRG_Set_Count(LRCLK_BRG,
- mclk_divisor * MCLK_DIVISOR * SCLK_DIVISOR);
-# else
- Daq_BRG_Set_Count(LRCLK_BRG, SCLK_DIVISOR);
-# endif
-
- /*
- * Restore the Interrupt state
- */
- if (flag) {
- enable_interrupts();
- }
-
- /* Enable the clock drivers */
- iopa->pdat &= ~SLRCLK_EN_MASK;
-}
-
-void Daq_Stop_Clocks(void)
-
-{
-#ifdef TIGHTEN_UP_BRG_TIMING
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- register uint mclk_brg; /* MCLK BRG value */
- register uint sclk_brg; /* SCLK BRG value */
- register uint lrclk_brg; /* LRCLK BRG value */
- unsigned long flag; /* Interrupt flags */
-#endif
-
-# ifdef TIGHTEN_UP_BRG_TIMING
- /*
- * Obtain MCLK BRG reset/disabled value
- */
-# if (MCLK_BRG == 0)
- mclk_brg = (*IM_BRGC1 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 1)
- mclk_brg = (*IM_BRGC2 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 2)
- mclk_brg = (*IM_BRGC3 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 3)
- mclk_brg = (*IM_BRGC4 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 4)
- mclk_brg = (*IM_BRGC5 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 5)
- mclk_brg = (*IM_BRGC6 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 6)
- mclk_brg = (*IM_BRGC7 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 7)
- mclk_brg = (*IM_BRGC8 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-
- /*
- * Obtain SCLK BRG reset/disabled value
- */
-# if (SCLK_BRG == 0)
- sclk_brg = (*IM_BRGC1 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 1)
- sclk_brg = (*IM_BRGC2 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 2)
- sclk_brg = (*IM_BRGC3 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 3)
- sclk_brg = (*IM_BRGC4 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 4)
- sclk_brg = (*IM_BRGC5 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 5)
- sclk_brg = (*IM_BRGC6 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 6)
- sclk_brg = (*IM_BRGC7 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 7)
- sclk_brg = (*IM_BRGC8 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-
- /*
- * Obtain LRCLK BRG reset/disabled value
- */
-# if (LRCLK_BRG == 0)
- lrclk_brg = (*IM_BRGC1 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 1)
- lrclk_brg = (*IM_BRGC2 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 2)
- lrclk_brg = (*IM_BRGC3 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 3)
- lrclk_brg = (*IM_BRGC4 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 4)
- lrclk_brg = (*IM_BRGC5 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 5)
- lrclk_brg = (*IM_BRGC6 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 6)
- lrclk_brg = (*IM_BRGC7 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 7)
- lrclk_brg = (*IM_BRGC8 | CPM_BRG_RST) & ~CPM_BRG_EN;
-# endif
-
- /*
- * Disable interrupt and save the current state
- */
- flag = disable_interrupts();
-
- /*
- * Set reset on MCLK BRG
- */
-# if (MCLK_BRG == 0)
- *IM_BRGC1 = mclk_brg;
-# endif
-# if (MCLK_BRG == 1)
- *IM_BRGC2 = mclk_brg;
-# endif
-# if (MCLK_BRG == 2)
- *IM_BRGC3 = mclk_brg;
-# endif
-# if (MCLK_BRG == 3)
- *IM_BRGC4 = mclk_brg;
-# endif
-# if (MCLK_BRG == 4)
- *IM_BRGC5 = mclk_brg;
-# endif
-# if (MCLK_BRG == 5)
- *IM_BRGC6 = mclk_brg;
-# endif
-# if (MCLK_BRG == 6)
- *IM_BRGC7 = mclk_brg;
-# endif
-# if (MCLK_BRG == 7)
- *IM_BRGC8 = mclk_brg;
-# endif
-
- /*
- * Set reset on SCLK BRG
- */
-# if (SCLK_BRG == 0)
- *IM_BRGC1 = sclk_brg;
-# endif
-# if (SCLK_BRG == 1)
- *IM_BRGC2 = sclk_brg;
-# endif
-# if (SCLK_BRG == 2)
- *IM_BRGC3 = sclk_brg;
-# endif
-# if (SCLK_BRG == 3)
- *IM_BRGC4 = sclk_brg;
-# endif
-# if (SCLK_BRG == 4)
- *IM_BRGC5 = sclk_brg;
-# endif
-# if (SCLK_BRG == 5)
- *IM_BRGC6 = sclk_brg;
-# endif
-# if (SCLK_BRG == 6)
- *IM_BRGC7 = sclk_brg;
-# endif
-# if (SCLK_BRG == 7)
- *IM_BRGC8 = sclk_brg;
-# endif
-
- /*
- * Set reset on LRCLK BRG
- */
-# if (LRCLK_BRG == 0)
- *IM_BRGC1 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 1)
- *IM_BRGC2 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 2)
- *IM_BRGC3 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 3)
- *IM_BRGC4 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 4)
- *IM_BRGC5 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 5)
- *IM_BRGC6 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 6)
- *IM_BRGC7 = lrclk_brg;
-# endif
-# if (LRCLK_BRG == 7)
- *IM_BRGC8 = lrclk_brg;
-# endif
-
- /*
- * Clear reset on MCLK BRG
- */
-# if (MCLK_BRG == 0)
- *IM_BRGC1 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 1)
- *IM_BRGC2 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 2)
- *IM_BRGC3 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 3)
- *IM_BRGC4 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 4)
- *IM_BRGC5 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 5)
- *IM_BRGC6 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 6)
- *IM_BRGC7 = mclk_brg & ~CPM_BRG_RST;
-# endif
-# if (MCLK_BRG == 7)
- *IM_BRGC8 = mclk_brg & ~CPM_BRG_RST;
-# endif
-
- /*
- * Clear reset on SCLK BRG
- */
-# if (SCLK_BRG == 0)
- *IM_BRGC1 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 1)
- *IM_BRGC2 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 2)
- *IM_BRGC3 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 3)
- *IM_BRGC4 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 4)
- *IM_BRGC5 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 5)
- *IM_BRGC6 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 6)
- *IM_BRGC7 = sclk_brg & ~CPM_BRG_RST;
-# endif
-# if (SCLK_BRG == 7)
- *IM_BRGC8 = sclk_brg & ~CPM_BRG_RST;
-# endif
-
- /*
- * Clear reset on LRCLK BRG
- */
-# if (LRCLK_BRG == 0)
- *IM_BRGC1 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 1)
- *IM_BRGC2 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 2)
- *IM_BRGC3 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 3)
- *IM_BRGC4 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 4)
- *IM_BRGC5 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 5)
- *IM_BRGC6 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 6)
- *IM_BRGC7 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-# if (LRCLK_BRG == 7)
- *IM_BRGC8 = lrclk_brg & ~CPM_BRG_RST;
-# endif
-
- /*
- * Restore the Interrupt state
- */
- if (flag) {
- enable_interrupts();
- }
-# else
- /*
- * Reset the clocks
- */
- Daq_BRG_Reset(MCLK_BRG);
- Daq_BRG_Reset(SCLK_BRG);
- Daq_BRG_Reset(LRCLK_BRG);
-# endif
-}
-
-void Daq_Start_Clocks(int sample_rate)
-
-{
-#ifdef TIGHTEN_UP_BRG_TIMING
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-
- register uint mclk_brg; /* MCLK BRG value */
- register uint sclk_brg; /* SCLK BRG value */
- register uint temp_lrclk_brg; /* Temporary LRCLK BRG value */
- register uint real_lrclk_brg; /* Permanent LRCLK BRG value */
- uint lrclk_brg; /* LRCLK BRG value */
- unsigned long flags; /* Interrupt flags */
- uint sclk_cnt; /* SCLK count */
- uint delay_cnt; /* Delay count */
-#endif
-
-# ifdef TIGHTEN_UP_BRG_TIMING
- /*
- * Obtain the enabled MCLK BRG value
- */
-# if (MCLK_BRG == 0)
- mclk_brg = (*IM_BRGC1 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 1)
- mclk_brg = (*IM_BRGC2 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 2)
- mclk_brg = (*IM_BRGC3 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 3)
- mclk_brg = (*IM_BRGC4 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 4)
- mclk_brg = (*IM_BRGC5 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 5)
- mclk_brg = (*IM_BRGC6 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 6)
- mclk_brg = (*IM_BRGC7 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (MCLK_BRG == 7)
- mclk_brg = (*IM_BRGC8 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-
- /*
- * Obtain the enabled SCLK BRG value
- */
-# if (SCLK_BRG == 0)
- sclk_brg = (*IM_BRGC1 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 1)
- sclk_brg = (*IM_BRGC2 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 2)
- sclk_brg = (*IM_BRGC3 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 3)
- sclk_brg = (*IM_BRGC4 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 4)
- sclk_brg = (*IM_BRGC5 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 5)
- sclk_brg = (*IM_BRGC6 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 6)
- sclk_brg = (*IM_BRGC7 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (SCLK_BRG == 7)
- sclk_brg = (*IM_BRGC8 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-
- /*
- * Obtain the enabled LRCLK BRG value
- */
-# if (LRCLK_BRG == 0)
- lrclk_brg = (*IM_BRGC1 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 1)
- lrclk_brg = (*IM_BRGC2 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 2)
- lrclk_brg = (*IM_BRGC3 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 3)
- lrclk_brg = (*IM_BRGC4 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 4)
- lrclk_brg = (*IM_BRGC5 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 5)
- lrclk_brg = (*IM_BRGC6 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 6)
- lrclk_brg = (*IM_BRGC7 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-# if (LRCLK_BRG == 7)
- lrclk_brg = (*IM_BRGC8 & ~CPM_BRG_RST) | CPM_BRG_EN;
-# endif
-
- /* Save off the real LRCLK value */
- real_lrclk_brg = lrclk_brg;
-
- /* Obtain the current SCLK count */
- sclk_cnt = ((sclk_brg & 0x00001FFE) >> 1) + 1;
-
- /* Compute the delay as a function of SCLK count */
- delay_cnt = ((sclk_cnt / 4) - 2) * 10 + 6;
- if (DaqSampleRate == 43402) {
- delay_cnt++;
- }
-
- /* Clear out the count */
- temp_lrclk_brg = sclk_brg & ~0x00001FFE;
-
- /* Insert the count */
- temp_lrclk_brg |= ((delay_cnt + (sclk_cnt / 2) - 1) << 1) & 0x00001FFE;
-
- /*
- * Disable interrupt and save the current state
- */
- flag = disable_interrupts();
-
- /*
- * Enable MCLK BRG
- */
-# if (MCLK_BRG == 0)
- *IM_BRGC1 = mclk_brg;
-# endif
-# if (MCLK_BRG == 1)
- *IM_BRGC2 = mclk_brg;
-# endif
-# if (MCLK_BRG == 2)
- *IM_BRGC3 = mclk_brg;
-# endif
-# if (MCLK_BRG == 3)
- *IM_BRGC4 = mclk_brg;
-# endif
-# if (MCLK_BRG == 4)
- *IM_BRGC5 = mclk_brg;
-# endif
-# if (MCLK_BRG == 5)
- *IM_BRGC6 = mclk_brg;
-# endif
-# if (MCLK_BRG == 6)
- *IM_BRGC7 = mclk_brg;
-# endif
-# if (MCLK_BRG == 7)
- *IM_BRGC8 = mclk_brg;
-# endif
-
- /*
- * Enable SCLK BRG
- */
-# if (SCLK_BRG == 0)
- *IM_BRGC1 = sclk_brg;
-# endif
-# if (SCLK_BRG == 1)
- *IM_BRGC2 = sclk_brg;
-# endif
-# if (SCLK_BRG == 2)
- *IM_BRGC3 = sclk_brg;
-# endif
-# if (SCLK_BRG == 3)
- *IM_BRGC4 = sclk_brg;
-# endif
-# if (SCLK_BRG == 4)
- *IM_BRGC5 = sclk_brg;
-# endif
-# if (SCLK_BRG == 5)
- *IM_BRGC6 = sclk_brg;
-# endif
-# if (SCLK_BRG == 6)
- *IM_BRGC7 = sclk_brg;
-# endif
-# if (SCLK_BRG == 7)
- *IM_BRGC8 = sclk_brg;
-# endif
-
- /*
- * Enable LRCLK BRG (1st time - temporary)
- */
-# if (LRCLK_BRG == 0)
- *IM_BRGC1 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 1)
- *IM_BRGC2 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 2)
- *IM_BRGC3 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 3)
- *IM_BRGC4 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 4)
- *IM_BRGC5 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 5)
- *IM_BRGC6 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 6)
- *IM_BRGC7 = temp_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 7)
- *IM_BRGC8 = temp_lrclk_brg;
-# endif
-
- /*
- * Enable LRCLK BRG (2nd time - permanent)
- */
-# if (LRCLK_BRG == 0)
- *IM_BRGC1 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 1)
- *IM_BRGC2 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 2)
- *IM_BRGC3 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 3)
- *IM_BRGC4 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 4)
- *IM_BRGC5 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 5)
- *IM_BRGC6 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 6)
- *IM_BRGC7 = real_lrclk_brg;
-# endif
-# if (LRCLK_BRG == 7)
- *IM_BRGC8 = real_lrclk_brg;
-# endif
-
- /*
- * Restore the Interrupt state
- */
- if (flag) {
- enable_interrupts();
- }
-# else
- /*
- * Enable the clocks
- */
- Daq_BRG_Enable(LRCLK_BRG);
- Daq_BRG_Enable(SCLK_BRG);
- Daq_BRG_Enable(MCLK_BRG);
-# endif
-}
-
-void Daq_Display_Clocks(void)
-
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- uint mclk_divisor; /* Detected MCLK divisor */
- uint sclk_divisor; /* Detected SCLK divisor */
-
- printf("\nBRG:\n");
- if (immr->im_brgc4 != 0) {
- printf("\tbrgc4\t0x%08x @ 0x%08x, %5d count, %d extc, %8s, MCLK\n",
- immr->im_brgc4,
- (uint)&(immr->im_brgc4),
- Daq_BRG_Get_Count(3),
- Daq_BRG_Get_ExtClk(3),
- Daq_BRG_Get_ExtClk_Description(3));
- }
- if (immr->im_brgc8 != 0) {
- printf("\tbrgc8\t0x%08x @ 0x%08x, %5d count, %d extc, %8s, SCLK\n",
- immr->im_brgc8,
- (uint)&(immr->im_brgc8),
- Daq_BRG_Get_Count(7),
- Daq_BRG_Get_ExtClk(7),
- Daq_BRG_Get_ExtClk_Description(7));
- }
- if (immr->im_brgc6 != 0) {
- printf("\tbrgc6\t0x%08x @ 0x%08x, %5d count, %d extc, %8s, LRCLK\n",
- immr->im_brgc6,
- (uint)&(immr->im_brgc6),
- Daq_BRG_Get_Count(5),
- Daq_BRG_Get_ExtClk(5),
- Daq_BRG_Get_ExtClk_Description(5));
- }
- if (immr->im_brgc1 != 0) {
- printf("\tbrgc1\t0x%08x @ 0x%08x, %5d count, %d extc, %8s, SMC1\n",
- immr->im_brgc1,
- (uint)&(immr->im_brgc1),
- Daq_BRG_Get_Count(0),
- Daq_BRG_Get_ExtClk(0),
- Daq_BRG_Get_ExtClk_Description(0));
- }
- if (immr->im_brgc2 != 0) {
- printf("\tbrgc2\t0x%08x @ 0x%08x, %5d count, %d extc, %8s, SMC2\n",
- immr->im_brgc2,
- (uint)&(immr->im_brgc2),
- Daq_BRG_Get_Count(1),
- Daq_BRG_Get_ExtClk(1),
- Daq_BRG_Get_ExtClk_Description(1));
- }
- if (immr->im_brgc3 != 0) {
- printf("\tbrgc3\t0x%08x @ 0x%08x, %5d count, %d extc, %8s, SCC1\n",
- immr->im_brgc3,
- (uint)&(immr->im_brgc3),
- Daq_BRG_Get_Count(2),
- Daq_BRG_Get_ExtClk(2),
- Daq_BRG_Get_ExtClk_Description(2));
- }
- if (immr->im_brgc5 != 0) {
- printf("\tbrgc5\t0x%08x @ 0x%08x, %5d count, %d extc, %8s\n",
- immr->im_brgc5,
- (uint)&(immr->im_brgc5),
- Daq_BRG_Get_Count(4),
- Daq_BRG_Get_ExtClk(4),
- Daq_BRG_Get_ExtClk_Description(4));
- }
- if (immr->im_brgc7 != 0) {
- printf("\tbrgc7\t0x%08x @ 0x%08x, %5d count, %d extc, %8s\n",
- immr->im_brgc7,
- (uint)&(immr->im_brgc7),
- Daq_BRG_Get_Count(6),
- Daq_BRG_Get_ExtClk(6),
- Daq_BRG_Get_ExtClk_Description(6));
- }
-
-# ifdef RUN_SCLK_ON_BRG_INT
- mclk_divisor = Daq_BRG_Rate(MCLK_BRG) / Daq_BRG_Rate(SCLK_BRG);
-# else
- mclk_divisor = Daq_BRG_Get_Count(SCLK_BRG);
-# endif
-# ifdef RUN_LRCLK_ON_BRG_INT
- sclk_divisor = Daq_BRG_Rate(SCLK_BRG) / Daq_BRG_Rate(LRCLK_BRG);
-# else
- sclk_divisor = Daq_BRG_Get_Count(LRCLK_BRG);
-# endif
-
- printf("\nADC/DAC Clocking (%d/%d):\n", sclk_divisor, mclk_divisor);
- printf("\tMCLK %8d Hz, or %3dx SCLK, or %3dx LRCLK\n",
- Daq_BRG_Rate(MCLK_BRG),
- mclk_divisor,
- mclk_divisor * sclk_divisor);
-# ifdef RUN_SCLK_ON_BRG_INT
- printf("\tSCLK %8d Hz, or %3dx LRCLK\n",
- Daq_BRG_Rate(SCLK_BRG),
- sclk_divisor);
-# else
- printf("\tSCLK %8d Hz, or %3dx LRCLK\n",
- Daq_BRG_Rate(MCLK_BRG) / mclk_divisor,
- sclk_divisor);
-# endif
-# ifdef RUN_LRCLK_ON_BRG_INT
- printf("\tLRCLK %8d Hz\n",
- Daq_BRG_Rate(LRCLK_BRG));
-# else
-# ifdef RUN_SCLK_ON_BRG_INT
- printf("\tLRCLK %8d Hz\n",
- Daq_BRG_Rate(SCLK_BRG) / sclk_divisor);
-# else
- printf("\tLRCLK %8d Hz\n",
- Daq_BRG_Rate(MCLK_BRG) / (mclk_divisor * sclk_divisor));
-# endif
-# endif
- printf("\n");
-}
diff --git a/board/sacsng/clkinit.h b/board/sacsng/clkinit.h
deleted file mode 100644
index 3f759dd..0000000
--- a/board/sacsng/clkinit.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * (C) Copyright 2002
- * Custom IDEAS, Inc. <www.cideas.com>
- * Jon Diekema <diekema@cideas.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SLRCLK_EN_MASK 0x00040000 /* PA13 - SLRCLK_EN* */
-
-#define MIN_SAMPLE_RATE 4000 /* Minimum sample rate */
-#define MAX_128x_SAMPLE_RATE 43402 /* Maximum 128x sample rate */
-#define MAX_64x_SAMPLE_RATE 86805 /* Maximum 64x sample rate */
-
-#define KHZ ((uint)1000)
-#define MHZ ((uint)(1000 * KHZ))
-
-#define MCLK_BRG 3 /* MCLK, Master CLocK for the A/D & D/A */
-#define SCLK_BRG 7 /* SCLK, Sample CLocK for the A/D & D/A */
-#define LRCLK_BRG 5 /* LRCLK, L/R CLocK for the A/D & D/A */
- /* 0 == BRG1 (used for SMC1) */
- /* 1 == BRG2 (used for SMC2) */
- /* 2 == BRG3 (used for SCC1) */
- /* 3 == BRG4 (MCLK) */
- /* 4 == BRG5 */
- /* 5 == BRG6 (LRCLK) */
- /* 6 == BRG7 */
- /* 7 == BRG8 (SCLK) */
-
-#define MCLK_DIVISOR 4 /* SCLK = MCLK / MCLK_DIVISOR */
-#define SCLK_DIVISOR (Daq64xSampling ? 64 : 128)
- /* LRCLK = SCLK / SCLK_DIVISOR */
-
-#define TIGHTEN_UP_BRG_EN_TIMING /* Tighten up the BRG enable timing */
-#define RUN_SCLK_ON_BRG_INT /* Run SCLK on BRG_INT instead of MCLK */
- /* The 8260 (Mask B.3) seems to have */
- /* problems generating SCLK from MCLK */
- /* via CLK9. */
-#define RUN_LRCLK_ON_BRG_INT /* Run LRCLK on BRG_INT instead of SCLK */
- /* The 8260 (Mask B.3) seems to have */
- /* problems generating LRCLK from SCLK */
-
-#define NUM_LRCLKS_TO_STABILIZE 1 /* Number of LRCLK period (sample) */
- /* to wait for the clock to stabilize */
-
-#define CPM_CLK (gd->bd->bi_cpmfreq)
-#define DFBRG 4
-#define BRG_INT_CLK (CPM_CLK * 2 / DFBRG)
- /* BRG = CPM * 2 / DFBRG (Sect 9.8) */
- /* BRG = CPM * 2 / 4 */
- /* BRG = CPM / 2 */
-
-#define CPM_BRG_EXTC_MASK ((uint)0x0000C000)
-#define CPM_BRG_EXTC_SHIFT 14
-
-#define CPM_BRG_DIV16_MASK ((uint)0x00000001)
-#define CPM_BRG_DIV16_SHIFT 1
-
-#define CPM_BRG_EXTC_BRGCLK 0
-#define CPM_BRG_EXTC_CLK3 1
-#define CPM_BRG_EXTC_CLK9 CPM_BRG_EXTC_CLK3
-#define CPM_BRG_EXTC_CLK5 2
-#define CPM_BRG_EXTC_CLK15 CPM_BRG_EXTC_CLK5
-
-#define IM_BRGC1 ((uint *)0xf00119f0)
-#define IM_BRGC2 ((uint *)0xf00119f4)
-#define IM_BRGC3 ((uint *)0xf00119f8)
-#define IM_BRGC4 ((uint *)0xf00119fc)
-#define IM_BRGC5 ((uint *)0xf00115f0)
-#define IM_BRGC6 ((uint *)0xf00115f4)
-#define IM_BRGC7 ((uint *)0xf00115f8)
-#define IM_BRGC8 ((uint *)0xf00115fc)
-
-/*
- * External declarations
- */
-
-extern int Daq64xSampling;
-
-extern void Daq_BRG_Reset(uint brg);
-extern void Daq_BRG_Run(uint brg);
-
-extern void Daq_BRG_Disable(uint brg);
-extern void Daq_BRG_Enable(uint brg);
-
-extern uint Daq_BRG_Get_Div16(uint brg);
-extern void Daq_BRG_Set_Div16(uint brg, uint div16);
-
-extern uint Daq_BRG_Get_Count(uint brg);
-extern void Daq_BRG_Set_Count(uint brg, uint brg_cnt);
-
-extern uint Daq_BRG_Get_ExtClk(uint brg);
-extern char* Daq_BRG_Get_ExtClk_Description(uint brg);
-extern void Daq_BRG_Set_ExtClk(uint brg, uint extc);
-
-extern uint Daq_BRG_Rate(uint brg);
-
-extern uint Daq_Get_SampleRate(void);
-
-extern void Daq_Init_Clocks(int sample_rate, int sample_64x);
-extern void Daq_Stop_Clocks(void);
-extern void Daq_Start_Clocks(int sample_rate);
-extern void Daq_Display_Clocks(void);
diff --git a/board/sacsng/flash.c b/board/sacsng/flash.c
deleted file mode 100644
index 686fb22..0000000
--- a/board/sacsng/flash.c
+++ /dev/null
@@ -1,507 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <configs/sacsng.h>
-
-
-#undef DEBUG
-
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-#endif
-#ifndef CONFIG_ENV_SIZE
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#endif
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_short *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- unsigned long size_b0, size_b1;
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- size_b0 = flash_get_size((vu_short *)CONFIG_SYS_FLASH0_BASE, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size_b0, size_b0<<20);
- }
-
- size_b1 = flash_get_size((vu_short *)CONFIG_SYS_FLASH1_BASE, &flash_info[1]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
- &flash_info[0]);
-#endif
-
- if (size_b1) {
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[1]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
- &flash_info[1]);
-#endif
- } else {
- flash_info[1].flash_id = FLASH_UNKNOWN;
- flash_info[1].sector_count = -1;
- }
-
- flash_info[0].size = size_b0;
- flash_info[1].size = size_b1;
-
- /*
- * We only report the primary flash for U-Boot's use.
- */
- return (size_b0);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_FUJ: printf ("FUJITSU "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM400B: printf ("AM29LV400B (4 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM400T: printf ("AM29LV400T (4 Mbit, top boot sector)\n");
- break;
- case FLASH_AM800B: printf ("AM29LV800B (8 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM800T: printf ("AM29LV800T (8 Mbit, top boot sector)\n");
- break;
- case FLASH_AM160B: printf ("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T: printf ("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B: printf ("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T: printf ("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- default: printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_short *addr, flash_info_t *info)
-{
- short i;
- ushort value;
- ulong base = (ulong)addr;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x0555] = 0xAAAA;
- addr[0x02AA] = 0x5555;
- addr[0x0555] = 0x9090;
- __asm__ __volatile__(" sync\n ");
-
- value = addr[0];
-#ifdef DEBUG
- printf("Flash manufacturer 0x%04X\n", value);
-#endif
-
- if(value == (ushort)AMD_MANUFACT) {
- info->flash_id = FLASH_MAN_AMD;
- } else if (value == (ushort)FUJ_MANUFACT) {
- info->flash_id = FLASH_MAN_FUJ;
- } else {
-#ifdef DEBUG
- printf("Unknown flash manufacturer 0x%04X\n", value);
-#endif
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
-
- value = addr[1]; /* device ID */
-#ifdef DEBUG
- printf("Flash type 0x%04X\n", value);
-#endif
-
- if(value == (ushort)AMD_ID_LV400T) {
- info->flash_id += FLASH_AM400T;
- info->sector_count = 11;
- info->size = 0x00080000; /* => 0.5 MB */
- } else if(value == (ushort)AMD_ID_LV400B) {
- info->flash_id += FLASH_AM400B;
- info->sector_count = 11;
- info->size = 0x00080000; /* => 0.5 MB */
- } else if(value == (ushort)AMD_ID_LV800T) {
- info->flash_id += FLASH_AM800T;
- info->sector_count = 19;
- info->size = 0x00100000; /* => 1 MB */
- } else if(value == (ushort)AMD_ID_LV800B) {
- info->flash_id += FLASH_AM800B;
- info->sector_count = 19;
- info->size = 0x00100000; /* => 1 MB */
- } else if(value == (ushort)AMD_ID_LV160T) {
- info->flash_id += FLASH_AM160T;
- info->sector_count = 35;
- info->size = 0x00200000; /* => 2 MB */
- } else if(value == (ushort)AMD_ID_LV160B) {
- info->flash_id += FLASH_AM160B;
- info->sector_count = 35;
- info->size = 0x00200000; /* => 2 MB */
- } else if(value == (ushort)AMD_ID_LV320T) {
- info->flash_id += FLASH_AM320T;
- info->sector_count = 67;
- info->size = 0x00400000; /* => 4 MB */
- } else if(value == (ushort)AMD_ID_LV320B) {
- info->flash_id += FLASH_AM320B;
- info->sector_count = 67;
- info->size = 0x00400000; /* => 4 MB */
- } else {
-#ifdef DEBUG
- printf("Unknown flash type 0x%04X\n", value);
- info->size = CONFIG_SYS_FLASH_SIZE;
-#else
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
-#endif
- }
-
- /* set up sector start address table */
- if (info->flash_id & FLASH_BTYPE) {
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00004000;
- info->start[2] = base + 0x00006000;
- info->start[3] = base + 0x00008000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] = base + ((i - 3) * 0x00010000);
- }
- } else {
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00004000;
- info->start[i--] = base + info->size - 0x00006000;
- info->start[i--] = base + info->size - 0x00008000;
- for (; i >= 0; i--) {
- info->start[i] = base + (i * 0x00010000);
- }
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (volatile unsigned short *)(info->start[i]);
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (volatile unsigned short *)info->start[0];
-
- }
-
- addr[0] = 0xF0F0; /* reset bank */
- __asm__ __volatile__(" sync\n ");
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- vu_short *addr = (vu_short*)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > FLASH_AMD_COMP)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAAAA;
- addr[0x02AA] = 0x5555;
- addr[0x0555] = 0x8080;
- addr[0x0555] = 0xAAAA;
- addr[0x02AA] = 0x5555;
- __asm__ __volatile__(" sync\n ");
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_short*)(info->start[sect]);
- addr[0] = 0x3030;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_short*)(info->start[l_sect]);
- while ((addr[0] & 0x0080) != 0x0080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- addr[0] = 0xF0F0; /* reset bank */
- __asm__ __volatile__(" sync\n ");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
-DONE:
- /* reset to read mode */
- addr = (vu_short*)info->start[0];
- addr[0] = 0xF0F0; /* reset bank */
- __asm__ __volatile__(" sync\n ");
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- vu_short *addr = (vu_short*)(info->start[0]);
- ulong start;
- int flag;
- int j;
-
- /* Check if Flash is (sufficiently) erased */
- if (((*(vu_long *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- /* The original routine was designed to write 32 bit words to
- * 32 bit wide memory. We have 16 bit wide memory so we do
- * two writes. We write the LSB first at dest+2 and then the
- * MSB at dest (lousy big endian).
- */
- dest += 2;
- for(j = 0; j < 2; j++) {
- addr[0x0555] = 0xAAAA;
- addr[0x02AA] = 0x5555;
- addr[0x0555] = 0xA0A0;
- __asm__ __volatile__(" sync\n ");
-
- *((vu_short *)dest) = (ushort)data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while (*(vu_short *)dest != (ushort)data) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- dest -= 2;
- data >>= 16;
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/sacsng/ioconfig.h b/board/sacsng/ioconfig.h
deleted file mode 100644
index ac8f152..0000000
--- a/board/sacsng/ioconfig.h
+++ /dev/null
@@ -1,217 +0,0 @@
-/*
- * I/O Port configuration table
- *
- * If conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-#ifdef SKIP
-#undef SKIP
-#endif
-
-#ifdef CONF
-#undef CONF
-#endif
-
-#ifdef DIN
-#undef DIN
-#endif
-
-#ifdef DOUT
-#undef DOUT
-#endif
-
-#ifdef GPIO
-#undef GPIO
-#endif
-
-#ifdef SPEC
-#undef SPEC
-#endif
-
-#ifdef ACTV
-#undef ACTV
-#endif
-
-#ifdef OPEN
-#undef OPEN
-#endif
-
-#define SKIP 0 /* SKIP over this port */
-#define CONF 1 /* CONFiguration the port */
-
-#define DIN 0 /* PDIRx 0: Direction IN */
-#define DOUT 1 /* PDIRx 1: Direction OUT */
-
-#define GPIO 0 /* PPARx 0: General Purpose I/O */
-#define SPEC 1 /* PPARx 1: dedicated to a peripheral function, */
- /* i.e. the port has a SPECial use. */
-
-#define ACTV 0 /* PODRx 0: ACTiVely driven as an output */
-#define OPEN 1 /* PODRx 1: OPEN-drain driver */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS8* */
- /* PA30 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS7* */
- /* PA29 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS6* */
- /* PA28 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS5* */
- /* PA27 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS4* */
- /* PA26 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS3* */
- /* PA25 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS2* */
- /* PA24 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* RODIS1* */
- /* PA23 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* ODIS_EN* */
- /* PA22 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* STLED2_EN* */
- /* PA21 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* STLED1_EN* */
- /* PA20 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* PLED3_EN* */
- /* PA19 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* PLED2_EN* */
- /* PA18 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* PLED1_EN* */
- /* PA17 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PA16 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* DAC_RST* */
- /* PA15 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* CH34SDATA_PU */
- /* PA14 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* CH12SDATA_PU */
- /* PA13 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* SLRCLK_EN* */
- /* PA12 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_4ACDC* */
- /* PA11 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_4TEDS* */
- /* PA10 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_4XTDS* */
- /* PA9 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_3ACDC* */
- /* PA8 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_3TEDS* */
- /* PA7 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_3XTDS* */
- /* PA6 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_2ACDC* */
- /* PA5 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_2TEDS* */
- /* PA4 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_2XTDS* */
- /* PA3 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PA2 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_1ACDC* */
- /* PA1 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* MTRX_1TEDS* */
- /* PA0 */ { CONF, GPIO, 0, DOUT, ACTV, 1 } /* MTRX_1XTDS* */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* FCC2 MII_TX_ER */
- /* PB30 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_RX_DV */
- /* PB29 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* FCC2 MII_TX_EN */
- /* PB28 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_RX_ER */
- /* PB27 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_COL */
- /* PB26 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_CRS */
- /* PB25 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* FCC2 MII_TXD3 */
- /* PB24 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* FCC2 MII_TXD2 */
- /* PB23 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* FCC2 MII_TXD1 */
- /* PB22 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* FCC2 MII_TXD0 */
- /* PB21 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_RXD0 */
- /* PB20 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_RXD1 */
- /* PB19 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_RXD2 */
- /* PB18 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* FCC2 MII_RXD3 */
- /* PB17 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PB16 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PB15 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PB14 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* L1RXDC1, BSDATA_ADC12 */
- /* PB13 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PB12 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* L1RSYNCC1, LRCLK */
- /* PB11 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* L1TXDD1, RSDATA_DAC12 */
- /* PB10 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* L1RXDD1, BSDATA_ADC34 */
- /* PB9 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PB8 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* L1RSYNCD1, LRCLK */
- /* PB7 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PB6 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* XCITE_SHDN */
- /* PB5 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* TRIGGER */
- /* PB4 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* ARM */
- /* PB3 */ { SKIP, GPIO, 0, DIN, ACTV, 0 }, /* pin doesn't exist */
- /* PB2 */ { SKIP, GPIO, 0, DIN, ACTV, 0 }, /* pin doesn't exist */
- /* PB1 */ { SKIP, GPIO, 0, DIN, ACTV, 0 }, /* pin doesn't exist */
- /* PB0 */ { SKIP, GPIO, 0, DIN, ACTV, 0 } /* pin doesn't exist */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC30 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC29 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* CLK3, MCLK */
- /* PC28 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* TOUT2* */
-#ifdef QQQ
- /* PC28 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* TOUT2* */
-#endif
- /* PC27 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* CLK5, SCLK */
- /* PC26 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC25 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* CLK7, SCLK */
- /* PC24 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC23 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* CLK9, MCLK */
- /* PC22 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC21 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* BRGO6 (LRCLK) */
- /* PC20 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC19 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* CLK13, MII_RXCLK */
- /* PC18 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* CLK14, MII_TXCLK */
- /* PC17 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* BRGO8 (SCLK) */
- /* PC16 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC15 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* SMC2_TX */
- /* PC14 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC13 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC12 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* TDM_STRB3 */
- /* PC11 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC10 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* TDM_STRB4 */
- /* PC9 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* BPDIS_IN3 */
- /* PC8 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* BPDIS_IN2 */
- /* PC7 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* BPDIS_IN1 */
- /* PC6 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PC5 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* BTST_IN2* */
- /* PC4 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* BTST_IN1* */
- /* PC3 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* MUSH_STAT */
- /* PC2 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* OUTDRV_STAT */
- /* PC1 */ { CONF, GPIO, 0, DOUT, OPEN, 1 }, /* PHY_MDIO */
- /* PC0 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* PHY_MDC */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* SCC1_RX */
- /* PD30 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* SCC1_TX */
- /* PD29 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD28 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD27 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD26 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD25 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD24 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD23 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD22 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD21 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD20 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* SPI_ADC_CS* */
- /* PD19 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* SPI_DAC_CS* */
-#if defined(CONFIG_SOFT_SPI)
- /* PD18 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* SPI_CLK */
- /* PD17 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* SPI_MOSI */
- /* PD16 */ { CONF, GPIO, 0, DIN, ACTV, 0 }, /* SPI_MISO */
-#else
- /* PD18 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* SPI_CLK */
- /* PD17 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* SPI_MOSI */
- /* PD16 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* SPI_MISO */
-#endif
-#if defined(CONFIG_SYS_I2C_SOFT)
- /* PD15 */ { CONF, GPIO, 0, DOUT, OPEN, 1 }, /* I2C_SDA */
- /* PD14 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* I2C_SCL */
-#else
-#if defined(CONFIG_HARD_I2C)
- /* PD15 */ { CONF, SPEC, 1, DIN, OPEN, 0 }, /* I2C_SDA */
- /* PD14 */ { CONF, SPEC, 1, DIN, OPEN, 0 }, /* I2C_SCL */
-#else /* normal I/O port pins */
- /* PD15 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* I2C_SDA */
- /* PD14 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* I2C_SCL */
-#endif
-#endif
- /* PD13 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* TDM_STRB1 */
- /* PD12 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* TDM_STRB2 */
- /* PD11 */ { CONF, GPIO, 0, DOUT, ACTV, 0 }, /* N/C */
- /* PD10 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* BRGO4 (MCLK) */
- /* PD9 */ { CONF, SPEC, 0, DOUT, ACTV, 0 }, /* SMC1_TX */
- /* PD8 */ { CONF, SPEC, 0, DIN, ACTV, 0 }, /* SMC1_RX */
- /* PD7 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* N/C */
- /* PD6 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* N/C */
- /* PD5 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* N/C */
- /* PD4 */ { CONF, SPEC, 1, DOUT, ACTV, 1 }, /* SMC2_RX */
- /* PD3 */ { SKIP, GPIO, 0, DIN, ACTV, 0 }, /* pin doesn't exist */
- /* PD2 */ { SKIP, GPIO, 0, DIN, ACTV, 0 }, /* pin doesn't exist */
- /* PD1 */ { SKIP, GPIO, 0, DIN, ACTV, 0 }, /* pin doesn't exist */
- /* PD0 */ { SKIP, GPIO, 0, DIN, ACTV, 0 } /* pin doesn't exist */
- }
-};
diff --git a/board/sacsng/sacsng.c b/board/sacsng/sacsng.c
deleted file mode 100644
index 91c4987..0000000
--- a/board/sacsng/sacsng.c
+++ /dev/null
@@ -1,848 +0,0 @@
-/*
- * (C) Copyright 2002
- * Custom IDEAS, Inc. <www.cideas.com>
- * Gerald Van Baren <vanbaren@cideas.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/u-boot.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <i2c.h>
-#include <spi.h>
-#include <command.h>
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-#include <status_led.h>
-#endif
-
-#ifdef CONFIG_ETHER_LOOPBACK_TEST
-extern void eth_loopback_test(void);
-#endif /* CONFIG_ETHER_LOOPBACK_TEST */
-
-#include "clkinit.h"
-#include "ioconfig.h" /* I/O configuration table */
-
-/*
- * PBI Page Based Interleaving
- * PSDMR_PBI page based interleaving
- * 0 bank based interleaving
- * External Address Multiplexing (EAMUX) adds a clock to address cycles
- * (this can help with marginal board layouts)
- * PSDMR_EAMUX adds a clock
- * 0 no extra clock
- * Buffer Command (BUFCMD) adds a clock to command cycles.
- * PSDMR_BUFCMD adds a clock
- * 0 no extra clock
- */
-#define CONFIG_PBI PSDMR_PBI
-#define PESSIMISTIC_SDRAM 0
-#define EAMUX 0 /* EST requires EAMUX */
-#define BUFCMD 0
-
-/*
- * ADC/DAC Defines:
- */
-#define INITIAL_SAMPLE_RATE 10016 /* Initial Daq sample rate */
-#define INITIAL_RIGHT_JUST 0 /* Initial DAC right justification */
-#define INITIAL_MCLK_DIVIDE 0 /* Initial MCLK Divide */
-#define INITIAL_SAMPLE_64X 1 /* Initial 64x clocking mode */
-#define INITIAL_SAMPLE_128X 0 /* Initial 128x clocking mode */
-
-/*
- * ADC Defines:
- */
-#define I2C_ADC_1_ADDR 0x0E /* I2C Address of the ADC #1 */
-#define I2C_ADC_2_ADDR 0x0F /* I2C Address of the ADC #2 */
-
-#define ADC_SDATA1_MASK 0x00020000 /* PA14 - CH12SDATA_PU */
-#define ADC_SDATA2_MASK 0x00010000 /* PA15 - CH34SDATA_PU */
-
-#define ADC_VREF_CAP 100 /* VREF capacitor in uF */
-#define ADC_INITIAL_DELAY (10 * ADC_VREF_CAP) /* 10 usec per uF, in usec */
-#define ADC_SDATA_DELAY 100 /* ADC SDATA release delay in usec */
-#define ADC_CAL_DELAY (1000000 / INITIAL_SAMPLE_RATE * 4500)
- /* Wait at least 4100 LRCLK's */
-
-#define ADC_REG1_FRAME_START 0x80 /* Frame start */
-#define ADC_REG1_GROUND_CAL 0x40 /* Ground calibration enable */
-#define ADC_REG1_ANA_MOD_PDOWN 0x20 /* Analog modulator section in power down */
-#define ADC_REG1_DIG_MOD_PDOWN 0x10 /* Digital modulator section in power down */
-
-#define ADC_REG2_128x 0x80 /* Oversample at 128x */
-#define ADC_REG2_CAL 0x40 /* System calibration enable */
-#define ADC_REG2_CHANGE_SIGN 0x20 /* Change sign enable */
-#define ADC_REG2_LR_DISABLE 0x10 /* Left/Right output disable */
-#define ADC_REG2_HIGH_PASS_DIS 0x08 /* High pass filter disable */
-#define ADC_REG2_SLAVE_MODE 0x04 /* Slave mode */
-#define ADC_REG2_DFS 0x02 /* Digital format select */
-#define ADC_REG2_MUTE 0x01 /* Mute */
-
-#define ADC_REG7_ADDR_ENABLE 0x80 /* Address enable */
-#define ADC_REG7_PEAK_ENABLE 0x40 /* Peak enable */
-#define ADC_REG7_PEAK_UPDATE 0x20 /* Peak update */
-#define ADC_REG7_PEAK_FORMAT 0x10 /* Peak display format */
-#define ADC_REG7_DIG_FILT_PDOWN 0x04 /* Digital filter power down enable */
-#define ADC_REG7_FIR2_IN_EN 0x02 /* External FIR2 input enable */
-#define ADC_REG7_PSYCHO_EN 0x01 /* External pyscho filter input enable */
-
-/*
- * DAC Defines:
- */
-
-#define I2C_DAC_ADDR 0x11 /* I2C Address of the DAC */
-
-#define DAC_RST_MASK 0x00008000 /* PA16 - DAC_RST* */
-#define DAC_RESET_DELAY 100 /* DAC reset delay in usec */
-#define DAC_INITIAL_DELAY 5000 /* DAC initialization delay in usec */
-
-#define DAC_REG1_AMUTE 0x80 /* Auto-mute */
-
-#define DAC_REG1_LEFT_JUST_24_BIT (0 << 4) /* Fmt 0: Left justified 24 bit */
-#define DAC_REG1_I2S_24_BIT (1 << 4) /* Fmt 1: I2S up to 24 bit */
-#define DAC_REG1_RIGHT_JUST_16BIT (2 << 4) /* Fmt 2: Right justified 16 bit */
-#define DAC_REG1_RIGHT_JUST_24BIT (3 << 4) /* Fmt 3: Right justified 24 bit */
-#define DAC_REG1_RIGHT_JUST_20BIT (4 << 4) /* Fmt 4: Right justified 20 bit */
-#define DAC_REG1_RIGHT_JUST_18BIT (5 << 4) /* Fmt 5: Right justified 18 bit */
-
-#define DAC_REG1_DEM_NO (0 << 2) /* No De-emphasis */
-#define DAC_REG1_DEM_44KHZ (1 << 2) /* 44.1KHz De-emphasis */
-#define DAC_REG1_DEM_48KHZ (2 << 2) /* 48KHz De-emphasis */
-#define DAC_REG1_DEM_32KHZ (3 << 2) /* 32KHz De-emphasis */
-
-#define DAC_REG1_SINGLE 0 /* 4- 50KHz sample rate */
-#define DAC_REG1_DOUBLE 1 /* 50-100KHz sample rate */
-#define DAC_REG1_QUAD 2 /* 100-200KHz sample rate */
-#define DAC_REG1_DSD 3 /* Direct Stream Data, DSD */
-
-#define DAC_REG5_INVERT_A 0x80 /* Invert channel A */
-#define DAC_REG5_INVERT_B 0x40 /* Invert channel B */
-#define DAC_REG5_I2C_MODE 0x20 /* Control port (I2C) mode */
-#define DAC_REG5_POWER_DOWN 0x10 /* Power down mode */
-#define DAC_REG5_MUTEC_A_B 0x08 /* Mutec A=B */
-#define DAC_REG5_FREEZE 0x04 /* Freeze */
-#define DAC_REG5_MCLK_DIV 0x02 /* MCLK divide by 2 */
-#define DAC_REG5_RESERVED 0x01 /* Reserved */
-
-/*
- * Check Board Identity:
- */
-
-int checkboard(void)
-{
- printf("SACSng\n");
-
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- volatile uchar c = 0;
- volatile uchar *ramaddr = (uchar *)(CONFIG_SYS_SDRAM_BASE + 0x8);
- uint psdmr = CONFIG_SYS_PSDMR;
- int i;
- uint psrt = 14; /* for no SPD */
- uint chipselects = 1; /* for no SPD */
- uint sdram_size = CONFIG_SYS_SDRAM0_SIZE * 1024 * 1024; /* for no SPD */
- uint or = CONFIG_SYS_OR2_PRELIM; /* for no SPD */
-
-#ifdef SDRAM_SPD_ADDR
- uint data_width;
- uint rows;
- uint banks;
- uint cols;
- uint caslatency;
- uint width;
- uint rowst;
- uint sdam;
- uint bsma;
- uint sda10;
- u_char data;
- u_char cksum;
- int j;
-#endif
-
-#ifdef SDRAM_SPD_ADDR
- /* Keep the compiler from complaining about potentially uninitialized vars */
- data_width = chipselects = rows = banks = cols = caslatency = psrt =
- 0;
-
- /*
- * Read the SDRAM SPD EEPROM via I2C.
- */
- i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1);
- cksum = data;
- for (j = 1; j < 64; j++) { /* read only the checksummed bytes */
- /* note: the I2C address autoincrements when alen == 0 */
- i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1);
- if (j == 5)
- chipselects = data & 0x0F;
- else if (j == 6)
- data_width = data;
- else if (j == 7)
- data_width |= data << 8;
- else if (j == 3)
- rows = data & 0x0F;
- else if (j == 4)
- cols = data & 0x0F;
- else if (j == 12) {
- /*
- * Refresh rate: this assumes the prescaler is set to
- * approximately 1uSec per tick.
- */
- switch (data & 0x7F) {
- default:
- case 0:
- psrt = 14; /* 15.625uS */
- break;
- case 1:
- psrt = 2; /* 3.9uS */
- break;
- case 2:
- psrt = 6; /* 7.8uS */
- break;
- case 3:
- psrt = 29; /* 31.3uS */
- break;
- case 4:
- psrt = 60; /* 62.5uS */
- break;
- case 5:
- psrt = 120; /* 125uS */
- break;
- }
- } else if (j == 17)
- banks = data;
- else if (j == 18) {
- caslatency = 3; /* default CL */
-#if(PESSIMISTIC_SDRAM)
- if ((data & 0x04) != 0)
- caslatency = 3;
- else if ((data & 0x02) != 0)
- caslatency = 2;
- else if ((data & 0x01) != 0)
- caslatency = 1;
-#else
- if ((data & 0x01) != 0)
- caslatency = 1;
- else if ((data & 0x02) != 0)
- caslatency = 2;
- else if ((data & 0x04) != 0)
- caslatency = 3;
-#endif
- else {
- printf("WARNING: Unknown CAS latency 0x%02X, using 3\n", data);
- }
- } else if (j == 63) {
- if (data != cksum) {
- printf("WARNING: Configuration data checksum failure:" " is 0x%02x, calculated 0x%02x\n", data, cksum);
- }
- }
- cksum += data;
- }
-
- /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
- if (caslatency < 2) {
- printf("WARNING: CL was %d, forcing to 2\n", caslatency);
- caslatency = 2;
- }
- if (rows > 14) {
- printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n",
- rows);
- rows = 14;
- }
- if (cols > 11) {
- printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n",
- cols);
- cols = 11;
- }
-
- if ((data_width != 64) && (data_width != 72)) {
- printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n",
- data_width);
- }
- width = 3; /* 2^3 = 8 bytes = 64 bits wide */
- /*
- * Convert banks into log2(banks)
- */
- if (banks == 2)
- banks = 1;
- else if (banks == 4)
- banks = 2;
- else if (banks == 8)
- banks = 3;
-
- sdram_size = 1 << (rows + cols + banks + width);
-
-#if(CONFIG_PBI == 0) /* bank-based interleaving */
- rowst = ((32 - 6) - (rows + cols + width)) * 2;
-#else
- rowst = 32 - (rows + banks + cols + width);
-#endif
-
- or = ~(sdram_size - 1) | /* SDAM address mask */
- ((banks - 1) << 13) | /* banks per device */
- (rowst << 9) | /* rowst */
- ((rows - 9) << 6); /* numr */
-
- memctl->memc_or2 = or;
-
- /*
- * SDAM specifies the number of columns that are multiplexed
- * (reference AN2165/D), defined to be (columns - 6) for page
- * interleave, (columns - 8) for bank interleave.
- *
- * BSMA is 14 - max(rows, cols). The bank select lines come
- * into play above the highest "address" line going into the
- * the SDRAM.
- */
-#if(CONFIG_PBI == 0) /* bank-based interleaving */
- sdam = cols - 8;
- bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
- sda10 = sdam + 2;
-#else
- sdam = cols - 6;
- bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
- sda10 = sdam;
-#endif
-#if(PESSIMISTIC_SDRAM)
- psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_16_CLK |
- PSDMR_PRETOACT_8W | PSDMR_ACTTORW_8W | PSDMR_WRC_4C |
- PSDMR_EAMUX | PSDMR_BUFCMD) | caslatency |
- ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
- (sdam << 24) | (bsma << 21) | (sda10 << 18);
-#else
- psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_7_CLK |
- PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */
- PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */
- PSDMR_WRC_1C | /* 1 clock + 7nSec */
- EAMUX | BUFCMD) |
- caslatency | ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
- (sdam << 24) | (bsma << 21) | (sda10 << 18);
-#endif
-#endif
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * Quote from Micron MT48LC8M16A2 data sheet:
- *
- * "...the SDRAM requires a 100uS delay prior to issuing any
- * command other than a COMMAND INHIBIT or NOP. Starting at some
- * point during this 100uS period and continuing at least through
- * the end of this period, COMMAND INHIBIT or NOP commands should
- * be applied."
- *
- * "Once the 100uS delay has been satisfied with at least one COMMAND
- * INHIBIT or NOP command having been applied, a /PRECHARGE command/
- * should be applied. All banks must then be precharged, thereby
- * placing the device in the all banks idle state."
- *
- * "Once in the idle state, /two/ AUTO REFRESH cycles must be
- * performed. After the AUTO REFRESH cycles are complete, the
- * SDRAM is ready for mode register programming."
- *
- * (/emphasis/ mine, gvb)
- *
- * The way I interpret this, Micron start up sequence is:
- * 1. Issue a PRECHARGE-BANK command (initial precharge)
- * 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged")
- * 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands
- * 4. Issue a MODE-SET command to initialize the mode register
- *
- * --------
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed@the address CONFIG_SYS_SDRAM_BASE.
- */
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
- memctl->memc_psrt = psrt;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
-
- /*
- * Do it a second time for the second set of chips if the DIMM has
- * two chip selects (double sided).
- */
- if (chipselects > 1) {
- ramaddr += sdram_size;
-
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM + sdram_size;
- memctl->memc_or3 = or;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
- }
-
- /* return total ram size */
- return (sdram_size * chipselects);
-}
-
-/*-----------------------------------------------------------------------
- * Board Control Functions
- */
-void board_poweroff(void)
-{
- while (1); /* hang forever */
-}
-
-
-#ifdef CONFIG_MISC_INIT_R
-/* ------------------------------------------------------------------------- */
-int misc_init_r(void)
-{
- /*
- * Note: iop is used by the I2C macros, and iopa by the ADC/DAC initialization.
- */
- volatile ioport_t *iopa =
- ioport_addr((immap_t *)CONFIG_SYS_IMMR, 0 /* port A */ );
- volatile ioport_t *iop =
- ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT);
-
- int reg; /* I2C register value */
- char *ep; /* Environment pointer */
- char str_buf[12]; /* sprintf output buffer */
- int sample_rate; /* ADC/DAC sample rate */
- int sample_64x; /* Use 64/4 clocking for the ADC/DAC */
- int sample_128x; /* Use 128/4 clocking for the ADC/DAC */
- int right_just; /* Is the data to the DAC right justified? */
- int mclk_divide; /* MCLK Divide */
- int quiet; /* Quiet or minimal output mode */
-
- quiet = 0;
-
- if ((ep = getenv("quiet")) != NULL)
- quiet = simple_strtol(ep, NULL, 10);
- else
- setenv("quiet", "0");
-
- /*
- * SACSng custom initialization:
- * Start the ADC and DAC clocks, since the Crystal parts do not
- * work on the I2C bus until the clocks are running.
- */
-
- sample_rate = INITIAL_SAMPLE_RATE;
- if ((ep = getenv("DaqSampleRate")) != NULL)
- sample_rate = simple_strtol(ep, NULL, 10);
-
- sample_64x = INITIAL_SAMPLE_64X;
- sample_128x = INITIAL_SAMPLE_128X;
- if ((ep = getenv("Daq64xSampling")) != NULL) {
- sample_64x = simple_strtol(ep, NULL, 10);
- if (sample_64x)
- sample_128x = 0;
- else
- sample_128x = 1;
- } else {
- if ((ep = getenv("Daq128xSampling")) != NULL) {
- sample_128x = simple_strtol(ep, NULL, 10);
- if (sample_128x)
- sample_64x = 0;
- else
- sample_64x = 1;
- }
- }
-
- /*
- * Stop the clocks and wait for at least 1 LRCLK period
- * to make sure the clocking has really stopped.
- */
- Daq_Stop_Clocks();
- udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE);
-
- /*
- * Initialize the clocks with the new rates
- */
- Daq_Init_Clocks(sample_rate, sample_64x);
- sample_rate = Daq_Get_SampleRate();
-
- /*
- * Start the clocks and wait for at least 1 LRCLK period
- * to make sure the clocking has become stable.
- */
- Daq_Start_Clocks(sample_rate);
- udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE);
-
- sprintf(str_buf, "%d", sample_rate);
- setenv("DaqSampleRate", str_buf);
-
- if (sample_64x) {
- setenv("Daq64xSampling", "1");
- setenv("Daq128xSampling", NULL);
- } else {
- setenv("Daq64xSampling", NULL);
- setenv("Daq128xSampling", "1");
- }
-
- /*
- * Display the ADC/DAC clocking information
- */
- if (!quiet)
- Daq_Display_Clocks();
-
- /*
- * Determine the DAC data justification
- */
-
- right_just = INITIAL_RIGHT_JUST;
- if ((ep = getenv("DaqDACRightJustified")) != NULL)
- right_just = simple_strtol(ep, NULL, 10);
-
- sprintf(str_buf, "%d", right_just);
- setenv("DaqDACRightJustified", str_buf);
-
- /*
- * Determine the DAC MCLK Divide
- */
-
- mclk_divide = INITIAL_MCLK_DIVIDE;
- if ((ep = getenv("DaqDACMClockDivide")) != NULL)
- mclk_divide = simple_strtol(ep, NULL, 10);
-
- sprintf(str_buf, "%d", mclk_divide);
- setenv("DaqDACMClockDivide", str_buf);
-
- /*
- * Initializing the I2C address in the Crystal A/Ds:
- *
- * 1) Wait for VREF cap to settle (10uSec per uF)
- * 2) Release pullup on SDATA
- * 3) Write the I2C address to register 6
- * 4) Enable address matching by setting the MSB in register 7
- */
-
- if (!quiet)
- printf("Initializing the ADC...\n");
-
- udelay(ADC_INITIAL_DELAY); /* 10uSec per uF of VREF cap */
-
- iopa->pdat &= ~ADC_SDATA1_MASK; /* release SDATA1 */
- udelay(ADC_SDATA_DELAY); /* arbitrary settling time */
-
- i2c_reg_write(0x00, 0x06, I2C_ADC_1_ADDR); /* set address */
- i2c_reg_write(I2C_ADC_1_ADDR, 0x07, /* turn on ADDREN */
- ADC_REG7_ADDR_ENABLE);
-
- i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* 128x, slave mode, !HPEN */
- (sample_64x ? 0 : ADC_REG2_128x) |
- ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE);
-
- reg = i2c_reg_read(I2C_ADC_1_ADDR, 0x06) & 0x7F;
- if (reg != I2C_ADC_1_ADDR) {
- printf("Init of ADC U10 failed: address is 0x%02X should be 0x%02X\n",
- reg, I2C_ADC_1_ADDR);
- }
-
- iopa->pdat &= ~ADC_SDATA2_MASK; /* release SDATA2 */
- udelay(ADC_SDATA_DELAY); /* arbitrary settling time */
-
- /* set address (do not set ADDREN yet) */
- i2c_reg_write(0x00, 0x06, I2C_ADC_2_ADDR);
-
- i2c_reg_write(I2C_ADC_2_ADDR, 0x02, /* 64x, slave mode, !HPEN */
- (sample_64x ? 0 : ADC_REG2_128x) |
- ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE);
-
- reg = i2c_reg_read(I2C_ADC_2_ADDR, 0x06) & 0x7F;
- if (reg != I2C_ADC_2_ADDR) {
- printf("Init of ADC U15 failed: address is 0x%02X should be 0x%02X\n",
- reg, I2C_ADC_2_ADDR);
- }
-
- i2c_reg_write(I2C_ADC_1_ADDR, 0x01, /* set FSTART and GNDCAL */
- ADC_REG1_FRAME_START | ADC_REG1_GROUND_CAL);
-
- i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* Start calibration */
- (sample_64x ? 0 : ADC_REG2_128x) |
- ADC_REG2_CAL |
- ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE);
-
- udelay(ADC_CAL_DELAY); /* a minimum of 4100 LRCLKs */
- i2c_reg_write(I2C_ADC_1_ADDR, 0x01, 0x00); /* remove GNDCAL */
-
- /*
- * Now that we have synchronized the ADC's, enable address
- * selection on the second ADC as well as the first.
- */
- i2c_reg_write(I2C_ADC_2_ADDR, 0x07, ADC_REG7_ADDR_ENABLE);
-
- /*
- * Initialize the Crystal DAC
- *
- * Two of the config lines are used for I2C so we have to set them
- * to the proper initialization state without inadvertantly
- * sending an I2C "start" sequence. When we bring the I2C back to
- * the normal state, we send an I2C "stop" sequence.
- */
- if (!quiet)
- printf("Initializing the DAC...\n");
-
- /*
- * Bring the I2C clock and data lines low for initialization
- */
- I2C_SCL(0);
- I2C_DELAY;
- I2C_SDA(0);
- I2C_ACTIVE;
- I2C_DELAY;
-
- /* Reset the DAC */
- iopa->pdat &= ~DAC_RST_MASK;
- udelay(DAC_RESET_DELAY);
-
- /* Release the DAC reset */
- iopa->pdat |= DAC_RST_MASK;
- udelay(DAC_INITIAL_DELAY);
-
- /*
- * Cause the DAC to:
- * Enable control port (I2C mode)
- * Going into power down
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x05,
- DAC_REG5_I2C_MODE | DAC_REG5_POWER_DOWN);
-
- /*
- * Cause the DAC to:
- * Enable control port (I2C mode)
- * Going into power down
- * . MCLK divide by 1
- * . MCLK divide by 2
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x05,
- DAC_REG5_I2C_MODE |
- DAC_REG5_POWER_DOWN |
- (mclk_divide ? DAC_REG5_MCLK_DIV : 0));
-
- /*
- * Cause the DAC to:
- * Auto-mute disabled
- * . Format 0, left justified 24 bits
- * . Format 3, right justified 24 bits
- * No de-emphasis
- * . Single speed mode
- * . Double speed mode
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x01,
- (right_just ? DAC_REG1_RIGHT_JUST_24BIT :
- DAC_REG1_LEFT_JUST_24_BIT) |
- DAC_REG1_DEM_NO |
- (sample_rate >=
- 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE));
-
- sprintf(str_buf, "%d",
- sample_rate >= 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE);
- setenv("DaqDACFunctionalMode", str_buf);
-
- /*
- * Cause the DAC to:
- * Enable control port (I2C mode)
- * Remove power down
- * . MCLK divide by 1
- * . MCLK divide by 2
- */
- i2c_reg_write(I2C_DAC_ADDR, 0x05,
- DAC_REG5_I2C_MODE |
- (mclk_divide ? DAC_REG5_MCLK_DIV : 0));
-
- /*
- * Create a I2C stop condition:
- * low->high on data while clock is high.
- */
- I2C_SCL(1);
- I2C_DELAY;
- I2C_SDA(1);
- I2C_DELAY;
- I2C_TRISTATE;
-
- if (!quiet)
- printf("\n");
-#ifdef CONFIG_ETHER_LOOPBACK_TEST
- /*
- * Run the Ethernet loopback test
- */
- eth_loopback_test();
-#endif /* CONFIG_ETHER_LOOPBACK_TEST */
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
- /*
- * Turn off the RED fail LED now that we are up and running.
- */
- status_led_set(STATUS_LED_RED, STATUS_LED_OFF);
-#endif
-
- return 0;
-}
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-/*
- * Show boot status: flash the LED if something goes wrong, indicating
- * that last thing that worked and thus, by implication, what is broken.
- *
- * This stores the last OK value in RAM so this will not work properly
- * before RAM is initialized. Since it is being used for indicating
- * boot status (i.e. after RAM is initialized), that is OK.
- */
-static void flash_code(uchar number, uchar modulo, uchar digits)
-{
- int j;
-
- /*
- * Recursively do upper digits.
- */
- if (digits > 1)
- flash_code(number / modulo, modulo, digits - 1);
-
- number = number % modulo;
-
- /*
- * Zero is indicated by one long flash (dash).
- */
- if (number == 0) {
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
- udelay(1000000);
- status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
- udelay(200000);
- } else {
- /*
- * Non-zero is indicated by short flashes, one per count.
- */
- for (j = 0; j < number; j++) {
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
- udelay(100000);
- status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
- udelay(200000);
- }
- }
- /*
- * Inter-digit pause: we've already waited 200 mSec, wait 1 sec total
- */
- udelay(700000);
-}
-
-static int last_boot_progress;
-
-void show_boot_progress(int status)
-{
- int i, j;
-
- if (status > 0) {
- last_boot_progress = status;
- } else {
- /*
- * If a specific failure code is given, flash this code
- * else just use the last success code we've seen
- */
- if (status < -1)
- last_boot_progress = -status;
-
- /*
- * Flash this code 5 times
- */
- for (j = 0; j < 5; j++) {
- /*
- * Houston, we have a problem.
- * Blink the last OK status which indicates where things failed.
- */
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
- flash_code(last_boot_progress, 5, 3);
-
- /*
- * Delay 5 seconds between repetitions,
- * with the fault LED blinking
- */
- for (i = 0; i < 5; i++) {
- status_led_set(STATUS_LED_RED,
- STATUS_LED_OFF);
- udelay(500000);
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
- udelay(500000);
- }
- }
-
- /*
- * Reset the board to retry initialization.
- */
- do_reset(NULL, 0, 0, NULL);
- }
-}
-#endif /* CONFIG_SHOW_BOOT_PROGRESS */
-
-
-/*
- * The following are used to control the SPI chip selects for the SPI command.
- */
-#if defined(CONFIG_CMD_SPI)
-
-#define SPI_ADC_CS_MASK 0x00000800
-#define SPI_DAC_CS_MASK 0x00001000
-
-static const u32 cs_mask[] = {
- SPI_ADC_CS_MASK,
- SPI_DAC_CS_MASK,
-};
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < sizeof(cs_mask) / sizeof(cs_mask[0]);
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- volatile ioport_t *iopd =
- ioport_addr((immap_t *) CONFIG_SYS_IMMR, 3 /* port D */ );
-
- iopd->pdat &= ~cs_mask[slave->cs];
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- volatile ioport_t *iopd =
- ioport_addr((immap_t *) CONFIG_SYS_IMMR, 3 /* port D */ );
-
- iopd->pdat |= cs_mask[slave->cs];
-}
-
-#endif
-
-#endif /* CONFIG_MISC_INIT_R */
diff --git a/configs/sacsng_defconfig b/configs/sacsng_defconfig
deleted file mode 100644
index 91cca23..0000000
--- a/configs/sacsng_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_SACSNG=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index c9b4b17..5b71bc9 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+sacsng powerpc mpc8260 - - Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
cogent_mpc8260 powerpc mpc8260 - - Murray Jensen <Murray.Jensen@csiro.au>
cogent_8xx powerpc mpc8xx - - Murray Jensen <Murray.Jensen@csiro.au>
ESTEEM192E powerpc mpc8xx - - Conn Clark <clark@esteem.com>
diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h
deleted file mode 100644
index 2dee315..0000000
--- a/include/configs/sacsng.h
+++ /dev/null
@@ -1,1038 +0,0 @@
-/*
- * (C) Copyright 2000
- * Murray Jensen <Murray.Jensen@cmst.csiro.au>
- *
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2001
- * Advent Networks, Inc. <http://www.adventnetworks.com>
- * Jay Monkman <jtm@smoothsmoothie.com>
- *
- * Configuration settings for the SACSng 8260 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
-
-#undef CONFIG_LOGBUFFER /* External logbuffer support */
-
-/*****************************************************************************
- *
- * These settings must match the way _your_ board is set up
- *
- *****************************************************************************/
-
-/* What is the oscillator's (UX2) frequency in Hz? */
-#define CONFIG_8260_CLKIN 66666600
-
-/*-----------------------------------------------------------------------
- * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual
- *-----------------------------------------------------------------------
- * What should MODCK_H be? It is dependent on the oscillator
- * frequency, MODCK[1-3], and desired CPM and core frequencies.
- * Here are some example values (all frequencies are in MHz):
- *
- * MODCK_H MODCK[1-3] Osc CPM Core S2-6 S2-7 S2-8
- * ------- ---------- --- --- ---- ----- ----- -----
- * 0x1 0x5 33 100 133 Open Close Open
- * 0x1 0x6 33 100 166 Open Open Close
- * 0x1 0x7 33 100 200 Open Open Open
- *
- * 0x2 0x2 33 133 133 Close Open Close
- * 0x2 0x3 33 133 166 Close Open Open
- * 0x2 0x4 33 133 200 Open Close Close
- * 0x2 0x5 33 133 233 Open Close Open
- * 0x2 0x6 33 133 266 Open Open Close
- *
- * 0x5 0x5 66 133 133 Open Close Open
- * 0x5 0x6 66 133 166 Open Open Close
- * 0x5 0x7 66 133 200 Open Open Open
- * 0x6 0x0 66 133 233 Close Close Close
- * 0x6 0x1 66 133 266 Close Close Open
- * 0x6 0x2 66 133 300 Close Open Close
- */
-#define CONFIG_SYS_SBC_MODCK_H 0x05
-
-/* Define this if you want to boot from 0x00000100. If you don't define
- * this, you will need to program the bootloader to 0xfff00000, and
- * get the hardware reset config words at 0xfe000000. The simplest
- * way to do that is to program the bootloader at both addresses.
- * It is suggested that you just let U-Boot live at 0x00000000.
- */
-#define CONFIG_SYS_SBC_BOOT_LOW 1
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sacsng/config.mk
- * The main FLASH is whichever is connected to *CS0.
- */
-#define CONFIG_SYS_FLASH0_BASE 0x40000000
-#define CONFIG_SYS_FLASH0_SIZE 2
-
-/* What should the base address of the secondary FLASH be and how big
- * is it (in Mbytes)? The secondary FLASH is whichever is connected
- * to *CS6.
- */
-#define CONFIG_SYS_FLASH1_BASE 0x60000000
-#define CONFIG_SYS_FLASH1_SIZE 2
-
-/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes
- */
-#define CONFIG_VERY_BIG_RAM 1
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)? This will normally auto-configure via the SPD.
-*/
-#define CONFIG_SYS_SDRAM0_BASE 0x00000000
-#define CONFIG_SYS_SDRAM0_SIZE 64
-
-/*
- * Memory map example with 64 MB DIMM:
- *
- * 0x0000 0000 Exception Vector code, 8k
- * :
- * 0x0000 1FFF
- * 0x0000 2000 Free for Application Use
- * :
- * :
- *
- * :
- * :
- * 0x03F5 FF30 Monitor Stack (Growing downward)
- * Monitor Stack Buffer (0x80)
- * 0x03F5 FFB0 Board Info Data
- * 0x03F6 0000 Malloc Arena
- * : CONFIG_ENV_SECT_SIZE, 16k
- * : CONFIG_SYS_MALLOC_LEN, 128k
- * 0x03FC 0000 RAM Copy of Monitor Code
- * : CONFIG_SYS_MONITOR_LEN, 256k
- * 0x03FF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1
- */
-
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU)
-
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#define CONFIG_CONS_ON_SMC 1 /* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on neither */
-#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-
-#undef CONFIG_ETHER_ON_SCC
-#define CONFIG_ETHER_ON_FCC
-#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
-
-#ifdef CONFIG_ETHER_ON_SCC
-#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
-#endif /* CONFIG_ETHER_ON_SCC */
-
-#ifdef CONFIG_ETHER_ON_FCC
-#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
-#undef CONFIG_ETHER_LOOPBACK_TEST /* Ethernet external loopback test */
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-/*
- * Port pins used for bit-banged MII communictions (if applicable).
- */
-
-#define MDIO_PORT 2 /* Port A=0, B=1, C=2, D=3 */
-#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE MDIO_DECLARE
-
-#define MDIO_ACTIVE (iop->pdir |= 0x40000000)
-#define MDIO_TRISTATE (iop->pdir &= ~0x40000000)
-#define MDIO_READ ((iop->pdat & 0x40000000) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= 0x40000000; \
- else iop->pdat &= ~0x40000000
-
-#define MDC(bit) if(bit) iop->pdat |= 0x80000000; \
- else iop->pdat &= ~0x80000000
-
-#define MIIDELAY udelay(50)
-#endif /* CONFIG_ETHER_ON_FCC */
-
-#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1)
-
-/*
- * - RX clk is CLK11
- * - TX clk is CLK12
- */
-# define CONFIG_SYS_CMXSCR_VALUE1 (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
-
-#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progress enabled */
-
-/*
- * Configure for RAM tests.
- */
-#undef CONFIG_SYS_DRAM_TEST /* calls other tests in board.c */
-
-
-/*
- * Status LED for power up status feedback.
- */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
-#define STATUS_LED_PAR im_ioport.iop_ppara
-#define STATUS_LED_DIR im_ioport.iop_pdira
-#define STATUS_LED_ODR im_ioport.iop_podra
-#define STATUS_LED_DAT im_ioport.iop_pdata
-
-#define STATUS_LED_BIT 0x00000800 /* LED 0 is on PA.20 */
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ)
-#define STATUS_LED_STATE STATUS_LED_OFF
-#define STATUS_LED_BIT1 0x00001000 /* LED 1 is on PA.19 */
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-#define STATUS_LED_BIT2 0x00002000 /* LED 2 is on PA.18 */
-#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ/2)
-#define STATUS_LED_STATE2 STATUS_LED_ON
-
-#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
-
-#define STATUS_LED_YELLOW 0
-#define STATUS_LED_GREEN 1
-#define STATUS_LED_RED 2
-#define STATUS_LED_BOOT 1
-
-
-/*
- * Select SPI support configuration
- */
-#define CONFIG_SOFT_SPI /* Enable SPI driver */
-#define MAX_SPI_BYTES 4 /* Maximum number of bytes we can handle */
-#undef DEBUG_SPI /* Disable SPI debugging */
-
-/*
- * Software (bit-bang) SPI driver configuration
- */
-#ifdef CONFIG_SOFT_SPI
-
-/*
- * Software (bit-bang) SPI driver configuration
- */
-#define I2C_SCLK 0x00002000 /* PD 18: Shift clock */
-#define I2C_MOSI 0x00004000 /* PD 17: Master Out, Slave In */
-#define I2C_MISO 0x00008000 /* PD 16: Master In, Slave Out */
-
-#define SPI_READ ((immr->im_ioport.iop_pdatd & I2C_MISO) != 0)
-#define SPI_SDA(bit) do { \
- if(bit) immr->im_ioport.iop_pdatd |= I2C_MOSI; \
- else immr->im_ioport.iop_pdatd &= ~I2C_MOSI; \
- } while (0)
-#define SPI_SCL(bit) do { \
- if(bit) immr->im_ioport.iop_pdatd |= I2C_SCLK; \
- else immr->im_ioport.iop_pdatd &= ~I2C_SCLK; \
- } while (0)
-#define SPI_DELAY /* No delay is needed */
-#endif /* CONFIG_SOFT_SPI */
-
-
-/*
- * select I2C support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(20) /* 1/4 I2C clock duration */
-
-/* Define this to reserve an entire FLASH sector for
- * environment variables. Otherwise, the environment will be
- * put in the same sector as U-Boot, and changing variables
- * will erase U-Boot temporarily
- */
-#define CONFIG_ENV_IN_OWN_SECT 1
-
-/* Define this to contain any number of null terminated strings that
- * will be part of the default environment compiled into the boot image.
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-"quiet=0\0" \
-"serverip=192.168.123.205\0" \
-"ipaddr=192.168.123.203\0" \
-"checkhostname=VR8500\0" \
-"reprog="\
- "bootp; " \
- "tftpboot 0x140000 /bdi2000/u-boot.bin; " \
- "protect off 60000000 6003FFFF; " \
- "erase 60000000 6003FFFF; " \
- "cp.b 140000 60000000 ${filesize}; " \
- "protect on 60000000 6003FFFF\0" \
-"copyenv="\
- "protect off 60040000 6004FFFF; " \
- "erase 60040000 6004FFFF; " \
- "cp.b 40040000 60040000 10000; " \
- "protect on 60040000 6004FFFF\0" \
-"copyprog="\
- "protect off 60000000 6003FFFF; " \
- "erase 60000000 6003FFFF; " \
- "cp.b 40000000 60000000 40000; " \
- "protect on 60000000 6003FFFF\0" \
-"zapenv="\
- "protect off 40040000 4004FFFF; " \
- "erase 40040000 4004FFFF; " \
- "protect on 40040000 4004FFFF\0" \
-"zapotherenv="\
- "protect off 60040000 6004FFFF; " \
- "erase 60040000 6004FFFF; " \
- "protect on 60040000 6004FFFF\0" \
-"root-on-initrd="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/ram0 rw quiet " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"root-on-initrd-debug="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/ram0 rw debug " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run debug-hook\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"root-on-nfs="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/nfs rw quiet " \
- "nfsroot=\\${serverip}:\\${rootpath} " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"root-on-nfs-debug="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/nfs rw debug " \
- "nfsroot=\\${serverip}:\\${rootpath} " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run debug-hook\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"debug-checkout="\
- "setenv checkhostname;" \
- "setenv ethaddr 00:09:70:00:00:01;" \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} debug " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "run debug-hook;" \
- "run boot-hook;" \
- "bootm\0" \
-"debug-hook="\
- "echo ipaddr ${ipaddr};" \
- "echo serverip ${serverip};" \
- "echo gatewayip ${gatewayip};" \
- "echo netmask ${netmask};" \
- "echo hostname ${hostname}\0" \
-"ana=run adc ; run dac\0" \
-"adc=run adc-12 ; run adc-34\0" \
-"adc-12=echo ### ADC-12 ; i2c md e 81 e\0" \
-"adc-34=echo ### ADC-34 ; i2c md f 81 e\0" \
-"dac=echo ### DAC ; i2c md 11 81 5\0" \
-"boot-hook=echo\0"
-
-/* What should the console's baud rate be? */
-#define CONFIG_BAUDRATE 9600
-
-/* Ethernet MAC address */
-#define CONFIG_ETHADDR 00:09:70:00:00:00
-
-/* The default Ethernet MAC address can be overwritten just once */
-#ifdef CONFIG_ETHADDR
-#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
-#endif
-
-/*
- * Define this to do some miscellaneous board-specific initialization.
- */
-#define CONFIG_MISC_INIT_R
-
-/* Set to a positive value to delay for running BOOTCOMMAND */
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
-
-/* Be selective on what keys can delay or stop the autoboot process
- * To stop use: " "
- */
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "Autobooting...\n"
-#define CONFIG_AUTOBOOT_STOP_STR " "
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define DEBUG_BOOTKEYS 0
-
-/* Define a command string that is automatically executed when no character
- * is read on the console interface withing "Boot Delay" after reset.
- */
-#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
-#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */
-
-#ifdef CONFIG_BOOT_ROOT_INITRD
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/ram0 rw quiet " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "run boot-hook;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_INITRD */
-
-#ifdef CONFIG_BOOT_ROOT_NFS
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} quiet " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "run boot-hook;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_NFS */
-
-#define CONFIG_BOOTP_RANDOM_DELAY /* Randomize the BOOTP retry delay */
-#define CONFIG_LIB_RAND
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-
-/* undef this to save memory */
-#define CONFIG_SYS_LONGHELP
-
-/* Monitor Command Prompt */
-
-#undef CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* When CONFIG_TIMESTAMP is selected, the timestamp (date and time)
- * of an image is printed by image commands like bootm or iminfo.
- */
-#define CONFIG_TIMESTAMP
-
-/* If this variable is defined, an environment variable named "ver"
- * is created by U-Boot showing the U-Boot version.
- */
-#define CONFIG_VERSION_VARIABLE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_KGDB
-
-#ifdef CONFIG_ETHER_ON_FCC
-#define CONFIG_CMD_MII
-#endif
-
-
-/* Where do the internal registers live? */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-#undef CONFIG_WATCHDOG /* disable the watchdog */
-
-/*****************************************************************************
- *
- * You should not have to modify any of the following settings
- *
- *****************************************************************************/
-
-#define CONFIG_SACSng 1 /* munged for the SACSng */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_BOOTM_HEADER_QUIET 1 /* Suppress the image header dump */
- /* in the bootm command. */
-#define CONFIG_SYS_BOOTM_PROGESS_QUIET 1 /* Suppress the progress displays, */
- /* "## <message>" from the bootm cmd */
-#define CONFIG_SYS_BOOTP_CHECK_HOSTNAME 1 /* If checkhostname environment is */
- /* defined, then the hostname param */
- /* validated against checkhostname. */
-#define CONFIG_SYS_BOOTP_RETRY_COUNT 0x40000000 /* # of timeouts before giving up */
-#define CONFIG_SYS_BOOTP_SHORT_RANDOM_DELAY 1 /* Use a short random delay value */
- /* (limited to maximum of 1024 msec) */
-#define CONFIG_SYS_CHK_FOR_ABORT_AT_LEAST_ONCE 1
- /* Check for abort key presses */
- /* at least once in dependent of the */
- /* CONFIG_BOOTDELAY value. */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Don't print console @ startup */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 1 /* Echo the inverted Ethernet link */
- /* state to the fault LED. */
-#define CONFIG_SYS_FAULT_MII_ADDR 0x02 /* MII addr of the PHY to check for */
- /* the Ethernet link state. */
-#define CONFIG_SYS_STATUS_FLASH_UNTIL_TFTP_OK 1 /* Keeping the status LED flashing */
- /* until the TFTP is successful. */
-#define CONFIG_SYS_STATUS_OFF_AFTER_NETBOOT 1 /* After a successful netboot, */
- /* turn off the STATUS LEDs. */
-#define CONFIG_SYS_TFTP_BLINK_STATUS_ON_DATA_IN 1 /* Blink status LED based on */
- /* incoming data. */
-#define CONFIG_SYS_TFTP_BLOCKS_PER_HASH 100 /* For every XX blocks, output a '#' */
- /* to signify that tftp is moving. */
-#define CONFIG_SYS_TFTP_HASHES_PER_FLASH 200 /* For every '#' hashes, */
- /* flash the status LED. */
-#define CONFIG_SYS_TFTP_HASHES_PER_LINE 65 /* Only output XX '#'s per line */
- /* during the tftp file transfer. */
-#define CONFIG_SYS_TFTP_PROGESS_QUIET 1 /* Suppress the progress displays */
- /* '#'s from the tftp command. */
-#define CONFIG_SYS_TFTP_STATUS_QUIET 1 /* Suppress the status displays */
- /* issued during the tftp command. */
-#define CONFIG_SYS_TFTP_TIMEOUT_COUNT 5 /* How many timeouts TFTP will allow */
- /* before it gives up. */
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-
-#define CONFIG_SYS_ALT_MEMTEST /* Select full-featured memory test */
-#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */
- /* the exception vector table */
- /* to the end of the DRAM */
- /* less monitor and malloc area */
-#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
-#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \
- + CONFIG_SYS_MALLOC_LEN \
- + CONFIG_ENV_SECT_SIZE \
- + CONFIG_SYS_STACK_USAGE )
-
-#define CONFIG_SYS_MEMTEST_END ( CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 \
- - CONFIG_SYS_MEM_END_USAGE )
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
-#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM0_SIZE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-#if defined(CONFIG_SYS_SBC_BOOT_LOW)
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
-#else
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
-#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) | \
- ((CONFIG_SYS_IMMR & 0x01000000) >> 7) | \
- ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER ( HRCW_BPS10 | \
- HRCW_DPPC11 | \
- CONFIG_SYS_SBC_HRCW_IMMR | \
- HRCW_MMR00 | \
- HRCW_LBPC11 | \
- HRCW_APPC10 | \
- HRCW_CS10PC00 | \
- (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) | \
- CONFIG_SYS_SBC_HRCW_BOOT_FLAGS )
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH0_BASE
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#undef CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT (64+4) /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-#ifndef CONFIG_SYS_RAMBOOT
-# define CONFIG_ENV_IS_IN_FLASH 1
-
-# ifdef CONFIG_ENV_IN_OWN_SECT
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-# define CONFIG_ENV_SECT_SIZE 0x10000
-# else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
-# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
-# endif /* CONFIG_ENV_IN_OWN_SECT */
-
-#else
-# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-# define CONFIG_ENV_SIZE 0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
- HID0_DCE |\
- HID0_ICFI |\
- HID0_DCI |\
- HID0_IFEM |\
- HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\
- HID0_IFEM |\
- HID0_ABE |\
- HID0_EMCP)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR (BCR_ETM)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11 |\
- SIUMCR_L2CPC00 |\
- SIUMCR_APPC10 |\
- SIUMCR_MMR00)
-
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
- SYPCR_BMT |\
- SYPCR_PBME |\
- SYPCR_LBME |\
- SYPCR_SWRI |\
- SYPCR_SWP |\
- SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
- SYPCR_BMT |\
- SYPCR_PBME |\
- SYPCR_LBME |\
- SYPCR_SWRI |\
- SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
- TMCNTSC_ALR |\
- TMCNTSC_TCF |\
- TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS |\
- PISCR_PTF |\
- PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR 0
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Initialize Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 16 bit FLASH (primary flash - 2MB)
- * 1 60x GPCM -- bit (Unused)
- * 2 60x SDRAM 64 bit SDRAM (DIMM)
- * 3 60x SDRAM 64 bit SDRAM (DIMM)
- * 4 60x GPCM -- bit (Unused)
- * 5 60x GPCM -- bit (Unused)
- * 6 60x GPCM 16 bit FLASH (secondary flash - 2MB)
- */
-
-/*-----------------------------------------------------------------------
- * BR0,BR1 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR0,OR1 - Option Register
- * Ref: Section 10.3.2 on page 10-18
- *-----------------------------------------------------------------------
- */
-
-/* Bank 0 - Primary FLASH
- */
-
-/* BR0 is configured as follows:
- *
- * - Base address of 0x40000000
- * - 16 bit port size
- * - Data errors checking is disabled
- * - Read and write access
- * - GPCM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-/* OR0 is configured as follows:
- *
- * - 4 MB
- * - *BCTL0 is asserted upon access to the current memory bank
- * - *CW / *WE are negated a quarter of a clock earlier
- * - *CS is output@the same time as the address lines
- * - Uses a clock cycle length of 5
- * - *PSDVAL is generated internally by the memory controller
- * unless *GTA is asserted earlier externally.
- * - Relaxed timing is generated by the GPCM for accesses
- * initiated to this memory region.
- * - One idle clock is inserted between a read access from the
- * current bank and the next access.
- */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX |\
- ORxG_EHTR)
-
-/*-----------------------------------------------------------------------
- * BR2,BR3 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR2,OR3 - Option Register
- * Ref: Section 10.3.2 on page 10-16
- *-----------------------------------------------------------------------
- */
-
-/* Bank 2,3 - SDRAM DIMM
- */
-
-/* The BR2 is configured as follows:
- *
- * - Base address of 0x00000000
- * - 64 bit port size (60x bus only)
- * - Data errors checking is disabled
- * - Read and write access
- * - SDRAM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-/* With a 64 MB DIMM, the OR2 is configured as follows:
- *
- * - 64 MB
- * - 4 internal banks per device
- * - Row start address bit is A8 with PSDMR[PBI] = 0
- * - 12 row address lines
- * - Back-to-back page mode
- * - Internal bank interleaving within save device enabled
- */
-#if (CONFIG_SYS_SDRAM0_SIZE == 64)
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A8 |\
- ORxS_NUMR_12)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*-----------------------------------------------------------------------
- * PSDMR - 60x Bus SDRAM Mode Register
- * Ref: Section 10.3.3 on page 10-21
- *-----------------------------------------------------------------------
- */
-
-/* Address that the DIMM SPD memory lives at.
- */
-#define SDRAM_SPD_ADDR 0x50
-
-#if (CONFIG_SYS_SDRAM0_SIZE == 64)
-/* With a 64 MB DIMM, the PSDMR is configured as follows:
- *
- * - Bank Based Interleaving,
- * - Refresh Enable,
- * - Address Multiplexing where A5 is output on A14 pin
- * (A6 on A15, and so on),
- * - use address pins A14-A16 as bank select,
- * - A9 is output on SDA10 during an ACTIVATE command,
- * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks,
- * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
- * is 3 clocks,
- * - earliest timing for READ/WRITE command after ACTIVATE command is
- * 2 clocks,
- * - earliest timing for PRECHARGE after last data was read is 1 clock,
- * - earliest timing for PRECHARGE after last data was written is 1 clock,
- * - CAS Latency is 2.
- */
-#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
- PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_3W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*
- * Shoot for approximately 1MHz on the prescaler.
- */
-#if (CONFIG_8260_CLKIN >= (60 * 1000 * 1000))
-#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV64
-#elif (CONFIG_8260_CLKIN >= (30 * 1000 * 1000))
-#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32
-#else
-#warning "Unconfigured bus clock freq: check CONFIG_SYS_MPTPR and CONFIG_SYS_PSRT are OK"
-#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32
-#endif
-#define CONFIG_SYS_PSRT 14
-
-
-/*-----------------------------------------------------------------------
- * BR6 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR6 - Option Register
- * Ref: Section 10.3.2 on page 10-18
- *-----------------------------------------------------------------------
- */
-
-/* Bank 6 - Secondary FLASH
- *
- * The secondary FLASH is connected to *CS6
- */
-#if (defined(CONFIG_SYS_FLASH1_BASE) && defined(CONFIG_SYS_FLASH1_SIZE))
-
-/* BR6 is configured as follows:
- *
- * - Base address of 0x60000000
- * - 16 bit port size
- * - Data errors checking is disabled
- * - Read and write access
- * - GPCM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-# define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_FLASH1_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-/* OR6 is configured as follows:
- *
- * - 2 MB
- * - *BCTL0 is asserted upon access to the current memory bank
- * - *CW / *WE are negated a quarter of a clock earlier
- * - *CS is output at the same time as the address lines
- * - Uses a clock cycle length of 5
- * - *PSDVAL is generated internally by the memory controller
- * unless *GTA is asserted earlier externally.
- * - Relaxed timing is generated by the GPCM for accesses
- * initiated to this memory region.
- * - One idle clock is inserted between a read access from the
- * current bank and the next access.
- */
-# define CONFIG_SYS_OR6_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH1_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX |\
- ORxG_EHTR)
-#endif /* (defined(CONFIG_SYS_FLASH1_BASE) && defined(CONFIG_SYS_FLASH1_SIZE)) */
-
-#endif /* __CONFIG_H */
--
1.9.1
next prev parent reply other threads:[~2014-12-15 14:26 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-12-15 14:26 [U-Boot] [PATCH 0/26] Start removing non-generic boards Masahiro Yamada
2014-12-15 14:26 ` [U-Boot] [PATCH 01/26] mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 02/26] powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 03/26] mpc8xx: remove ELPT860 board support Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 04/26] mpc8xx: remove KUP4X, KUP4K " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 05/26] mpc8xx: remove SPD823TS " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 06/26] mpc8xx: remove RRvision " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 07/26] mpc8xx: remove R360MPI " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 08/26] mpc8xx: remove NETVIA " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 09/26] mpc8xx: remove lwmon " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 10/26] mpc8xx: remove IVMS8, IVML24 " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 11/26] mpc8xx: remove IP860 " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 12/26] mpc8xx: remove ESTEEM192E " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 13/26] powerpc: remove cogent_8xx, cogent_mpc8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` Masahiro Yamada [this message]
2015-01-05 18:21 ` [U-Boot] [PATCH 14/26] mpc8260: remove sacsng " Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 15/26] mpc8260: remove ppmc8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 16/26] mpc8260: remove ep8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 17/26] mpc8260: remove VoVPN-GW " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 18/26] mpc8260: remove MPC8266ADS " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 19/26] mpc8260: remove PM825, PM826, PM828 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 20/26] mpc8260: remove muas3001 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 21/26] mpc8260: remove IPHASE4539 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 22/26] mpc8260: remove gw8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 23/26] mpc8260: remove ep82xxm " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 24/26] mpc8260: remove CPU86, CPU87 " Masahiro Yamada
2015-01-05 18:22 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 25/26] mpc8260: remove atc " Masahiro Yamada
2014-12-15 14:26 ` [U-Boot] [PATCH 26/26] powerpc: mpc824x: remove MPC824X cpu support Masahiro Yamada
2014-12-15 16:46 ` York Sun
2015-01-05 18:22 ` Tom Rini
2015-01-05 15:44 ` [U-Boot] [PATCH 0/26] Start removing non-generic boards Masahiro YAMADA
2015-01-05 18:28 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1418653608-14177-15-git-send-email-yamada.m@jp.panasonic.com \
--to=yamada.m@jp.panasonic.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.