From: Masahiro Yamada <yamada.m@jp.panasonic.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 26/26] powerpc: mpc824x: remove MPC824X cpu support
Date: Mon, 15 Dec 2014 23:26:31 +0900 [thread overview]
Message-ID: <1418653608-14177-27-git-send-email-yamada.m@jp.panasonic.com> (raw)
In-Reply-To: <1418653608-14177-1-git-send-email-yamada.m@jp.panasonic.com>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
---
MAKEALL | 6 -
README | 5 -
arch/powerpc/Kconfig | 4 -
arch/powerpc/cpu/mpc824x/Kconfig | 48 --
arch/powerpc/cpu/mpc824x/Makefile | 11 -
arch/powerpc/cpu/mpc824x/config.mk | 8 -
arch/powerpc/cpu/mpc824x/cpu.c | 262 ------
arch/powerpc/cpu/mpc824x/cpu_init.c | 311 -------
arch/powerpc/cpu/mpc824x/drivers/epic.h | 1 -
arch/powerpc/cpu/mpc824x/drivers/epic/README | 102 ---
arch/powerpc/cpu/mpc824x/drivers/epic/epic.h | 163 ----
arch/powerpc/cpu/mpc824x/drivers/epic/epic1.c | 517 ------------
arch/powerpc/cpu/mpc824x/drivers/epic/epic2.S | 196 -----
arch/powerpc/cpu/mpc824x/drivers/epic/epicutil.S | 57 --
arch/powerpc/cpu/mpc824x/drivers/errors.h | 212 -----
arch/powerpc/cpu/mpc824x/drivers/i2c/i2c.c | 254 ------
arch/powerpc/cpu/mpc824x/interrupts.c | 77 --
arch/powerpc/cpu/mpc824x/pci.c | 75 --
arch/powerpc/cpu/mpc824x/speed.c | 102 ---
arch/powerpc/cpu/mpc824x/start.S | 724 -----------------
arch/powerpc/cpu/mpc824x/traps.c | 194 -----
arch/powerpc/cpu/mpc824x/u-boot.lds | 76 --
arch/powerpc/include/asm/processor.h | 2 -
board/a3000/Kconfig | 9 -
board/a3000/MAINTAINERS | 6 -
board/a3000/Makefile | 8 -
board/a3000/README | 17 -
board/a3000/a3000.c | 101 ---
board/a3000/flash.c | 438 ----------
board/cpc45/Kconfig | 9 -
board/cpc45/MAINTAINERS | 7 -
board/cpc45/Makefile | 8 -
board/cpc45/cpc45.c | 250 ------
board/cpc45/flash.c | 506 ------------
board/cpc45/ide.c | 128 ---
board/cpc45/pd67290.c | 797 ------------------
board/cpc45/plx9030.c | 156 ----
board/cu824/Kconfig | 9 -
board/cu824/MAINTAINERS | 6 -
board/cu824/Makefile | 8 -
board/cu824/README | 453 -----------
board/cu824/cu824.c | 83 --
board/cu824/flash.c | 470 -----------
board/eXalion/Kconfig | 9 -
board/eXalion/MAINTAINERS | 6 -
board/eXalion/Makefile | 8 -
board/eXalion/eXalion.c | 283 -------
board/eXalion/eXalion.h | 36 -
board/eXalion/piix_pci.h | 156 ----
board/musenki/Kconfig | 9 -
board/musenki/MAINTAINERS | 6 -
board/musenki/Makefile | 8 -
board/musenki/README | 298 -------
board/musenki/flash.c | 496 ------------
board/musenki/musenki.c | 94 ---
board/mvblue/Kconfig | 9 -
board/mvblue/MAINTAINERS | 6 -
board/mvblue/Makefile | 8 -
board/mvblue/flash.c | 570 -------------
board/mvblue/mvblue.c | 253 ------
board/mvblue/u-boot.lds | 86 --
board/sandpoint/Kconfig | 19 -
board/sandpoint/MAINTAINERS | 12 -
board/sandpoint/Makefile | 8 -
board/sandpoint/README | 411 ----------
board/sandpoint/dinkdl | 2 -
board/sandpoint/flash.c | 748 -----------------
board/sandpoint/sandpoint.c | 91 ---
board/sandpoint/u-boot.lds | 84 --
board/utx8245/Kconfig | 9 -
board/utx8245/MAINTAINERS | 6 -
board/utx8245/Makefile | 13 -
board/utx8245/flash.c | 544 -------------
board/utx8245/utx8245.c | 119 ---
common/cmd_pcmcia.c | 3 -
configs/A3000_defconfig | 3 -
configs/CPC45_ROMBOOT_defconfig | 4 -
configs/CPC45_defconfig | 3 -
configs/CU824_defconfig | 3 -
configs/MUSENKI_defconfig | 3 -
configs/MVBLUE_defconfig | 3 -
configs/Sandpoint8240_defconfig | 3 -
configs/Sandpoint8245_defconfig | 3 -
configs/eXalion_defconfig | 3 -
configs/utx8245_defconfig | 3 -
doc/README.scrapyard | 9 +
drivers/pcmcia/Makefile | 1 -
drivers/pcmcia/i82365.c | 989 -----------------------
include/configs/A3000.h | 293 -------
include/configs/CPC45.h | 489 -----------
include/configs/CU824.h | 286 -------
include/configs/MUSENKI.h | 275 -------
include/configs/MVBLUE.h | 325 --------
include/configs/Sandpoint8240.h | 398 ---------
include/configs/Sandpoint8245.h | 376 ---------
include/configs/eXalion.h | 433 ----------
include/configs/utx8245.h | 408 ----------
include/mpc824x.h | 523 ------------
include/pci.h | 4 -
include/pcmcia/cirrus.h | 180 -----
include/pcmcia/i82365.h | 154 ----
include/pcmcia/ss.h | 133 ---
include/pcmcia/ti113x.h | 234 ------
include/ppc_asm.tmpl | 4 +-
post/drivers/memory.c | 2 +-
105 files changed, 12 insertions(+), 16821 deletions(-)
delete mode 100644 arch/powerpc/cpu/mpc824x/Kconfig
delete mode 100644 arch/powerpc/cpu/mpc824x/Makefile
delete mode 100644 arch/powerpc/cpu/mpc824x/config.mk
delete mode 100644 arch/powerpc/cpu/mpc824x/cpu.c
delete mode 100644 arch/powerpc/cpu/mpc824x/cpu_init.c
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/epic.h
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/epic/README
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/epic/epic.h
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/epic/epic1.c
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/epic/epic2.S
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/epic/epicutil.S
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/errors.h
delete mode 100644 arch/powerpc/cpu/mpc824x/drivers/i2c/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc824x/interrupts.c
delete mode 100644 arch/powerpc/cpu/mpc824x/pci.c
delete mode 100644 arch/powerpc/cpu/mpc824x/speed.c
delete mode 100644 arch/powerpc/cpu/mpc824x/start.S
delete mode 100644 arch/powerpc/cpu/mpc824x/traps.c
delete mode 100644 arch/powerpc/cpu/mpc824x/u-boot.lds
delete mode 100644 board/a3000/Kconfig
delete mode 100644 board/a3000/MAINTAINERS
delete mode 100644 board/a3000/Makefile
delete mode 100644 board/a3000/README
delete mode 100644 board/a3000/a3000.c
delete mode 100644 board/a3000/flash.c
delete mode 100644 board/cpc45/Kconfig
delete mode 100644 board/cpc45/MAINTAINERS
delete mode 100644 board/cpc45/Makefile
delete mode 100644 board/cpc45/cpc45.c
delete mode 100644 board/cpc45/flash.c
delete mode 100644 board/cpc45/ide.c
delete mode 100644 board/cpc45/pd67290.c
delete mode 100644 board/cpc45/plx9030.c
delete mode 100644 board/cu824/Kconfig
delete mode 100644 board/cu824/MAINTAINERS
delete mode 100644 board/cu824/Makefile
delete mode 100644 board/cu824/README
delete mode 100644 board/cu824/cu824.c
delete mode 100644 board/cu824/flash.c
delete mode 100644 board/eXalion/Kconfig
delete mode 100644 board/eXalion/MAINTAINERS
delete mode 100644 board/eXalion/Makefile
delete mode 100644 board/eXalion/eXalion.c
delete mode 100644 board/eXalion/eXalion.h
delete mode 100644 board/eXalion/piix_pci.h
delete mode 100644 board/musenki/Kconfig
delete mode 100644 board/musenki/MAINTAINERS
delete mode 100644 board/musenki/Makefile
delete mode 100644 board/musenki/README
delete mode 100644 board/musenki/flash.c
delete mode 100644 board/musenki/musenki.c
delete mode 100644 board/mvblue/Kconfig
delete mode 100644 board/mvblue/MAINTAINERS
delete mode 100644 board/mvblue/Makefile
delete mode 100644 board/mvblue/flash.c
delete mode 100644 board/mvblue/mvblue.c
delete mode 100644 board/mvblue/u-boot.lds
delete mode 100644 board/sandpoint/Kconfig
delete mode 100644 board/sandpoint/MAINTAINERS
delete mode 100644 board/sandpoint/Makefile
delete mode 100644 board/sandpoint/README
delete mode 100644 board/sandpoint/dinkdl
delete mode 100644 board/sandpoint/flash.c
delete mode 100644 board/sandpoint/sandpoint.c
delete mode 100644 board/sandpoint/u-boot.lds
delete mode 100644 board/utx8245/Kconfig
delete mode 100644 board/utx8245/MAINTAINERS
delete mode 100644 board/utx8245/Makefile
delete mode 100644 board/utx8245/flash.c
delete mode 100644 board/utx8245/utx8245.c
delete mode 100644 configs/A3000_defconfig
delete mode 100644 configs/CPC45_ROMBOOT_defconfig
delete mode 100644 configs/CPC45_defconfig
delete mode 100644 configs/CU824_defconfig
delete mode 100644 configs/MUSENKI_defconfig
delete mode 100644 configs/MVBLUE_defconfig
delete mode 100644 configs/Sandpoint8240_defconfig
delete mode 100644 configs/Sandpoint8245_defconfig
delete mode 100644 configs/eXalion_defconfig
delete mode 100644 configs/utx8245_defconfig
delete mode 100644 drivers/pcmcia/i82365.c
delete mode 100644 include/configs/A3000.h
delete mode 100644 include/configs/CPC45.h
delete mode 100644 include/configs/CU824.h
delete mode 100644 include/configs/MUSENKI.h
delete mode 100644 include/configs/MVBLUE.h
delete mode 100644 include/configs/Sandpoint8240.h
delete mode 100644 include/configs/Sandpoint8245.h
delete mode 100644 include/configs/eXalion.h
delete mode 100644 include/configs/utx8245.h
delete mode 100644 include/mpc824x.h
delete mode 100644 include/pcmcia/cirrus.h
delete mode 100644 include/pcmcia/i82365.h
delete mode 100644 include/pcmcia/ss.h
delete mode 100644 include/pcmcia/ti113x.h
diff --git a/MAKEALL b/MAKEALL
index 4822054..208232e 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -292,12 +292,6 @@ LIST_8xx="$(targets_by_cpu mpc8xx)"
LIST_4xx="$(targets_by_cpu ppc4xx)"
#########################################################################
-## MPC824x Systems
-#########################################################################
-
-LIST_824x="$(targets_by_cpu mpc824x)"
-
-#########################################################################
## MPC8260 Systems (includes 8250, 8255 etc.)
#########################################################################
diff --git a/README b/README
index 4ca04d0..43aa3af 100644
--- a/README
+++ b/README
@@ -186,7 +186,6 @@ Directory Hierarchy:
/mpc5xx Files specific to Freescale MPC5xx CPUs
/mpc5xxx Files specific to Freescale MPC5xxx CPUs
/mpc8xx Files specific to Freescale MPC8xx CPUs
- /mpc824x Files specific to Freescale MPC824x CPUs
/mpc8260 Files specific to Freescale MPC8260 CPUs
/mpc85xx Files specific to Freescale MPC85xx CPUs
/ppc4xx Files specific to AMCC PowerPC 4xx CPUs
@@ -326,10 +325,6 @@ The following options need to be configured:
multiple fs option at one time
for marvell soc family
-- MPC824X Family Member (if CONFIG_MPC824X is defined)
- Define exactly one of
- CONFIG_MPC8240, CONFIG_MPC8245
-
- 8xx CPU Options: (if using an MPC8xx CPU)
CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
get_gclk_freq() cannot work
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 6f96c7c..7a50301 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -19,9 +19,6 @@ config 5xx
config MPC5xxx
bool "MPC5xxx"
-config MPC824X
- bool "MPC824X"
-
config MPC8260
bool "MPC8260"
@@ -46,7 +43,6 @@ source "arch/powerpc/cpu/74xx_7xx/Kconfig"
source "arch/powerpc/cpu/mpc512x/Kconfig"
source "arch/powerpc/cpu/mpc5xx/Kconfig"
source "arch/powerpc/cpu/mpc5xxx/Kconfig"
-source "arch/powerpc/cpu/mpc824x/Kconfig"
source "arch/powerpc/cpu/mpc8260/Kconfig"
source "arch/powerpc/cpu/mpc83xx/Kconfig"
source "arch/powerpc/cpu/mpc85xx/Kconfig"
diff --git a/arch/powerpc/cpu/mpc824x/Kconfig b/arch/powerpc/cpu/mpc824x/Kconfig
deleted file mode 100644
index 4f98423..0000000
--- a/arch/powerpc/cpu/mpc824x/Kconfig
+++ /dev/null
@@ -1,48 +0,0 @@
-menu "mpc824x CPU"
- depends on MPC824X
-
-config SYS_CPU
- default "mpc824x"
-
-choice
- prompt "Target select"
-
-config TARGET_A3000
- bool "Support A3000"
-
-config TARGET_CPC45
- bool "Support CPC45"
-
-config TARGET_CU824
- bool "Support CU824"
-
-config TARGET_EXALION
- bool "Support eXalion"
-
-config TARGET_MUSENKI
- bool "Support MUSENKI"
-
-config TARGET_MVBLUE
- bool "Support MVBLUE"
-
-config TARGET_SANDPOINT8240
- bool "Support Sandpoint8240"
-
-config TARGET_SANDPOINT8245
- bool "Support Sandpoint8245"
-
-config TARGET_UTX8245
- bool "Support utx8245"
-
-endchoice
-
-source "board/a3000/Kconfig"
-source "board/cpc45/Kconfig"
-source "board/cu824/Kconfig"
-source "board/eXalion/Kconfig"
-source "board/musenki/Kconfig"
-source "board/mvblue/Kconfig"
-source "board/sandpoint/Kconfig"
-source "board/utx8245/Kconfig"
-
-endmenu
diff --git a/arch/powerpc/cpu/mpc824x/Makefile b/arch/powerpc/cpu/mpc824x/Makefile
deleted file mode 100644
index 2c8be92..0000000
--- a/arch/powerpc/cpu/mpc824x/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-extra-y = start.o
-obj-y = traps.o cpu.o cpu_init.o interrupts.o speed.o \
- drivers/epic/epic1.o drivers/i2c/i2c.o pci.o
-obj-y += ../mpc8260/bedbug_603e.o
diff --git a/arch/powerpc/cpu/mpc824x/config.mk b/arch/powerpc/cpu/mpc824x/config.mk
deleted file mode 100644
index ecfb07e..0000000
--- a/arch/powerpc/cpu/mpc824x/config.mk
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2010
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -mstring -mcpu=603e -msoft-float
diff --git a/arch/powerpc/cpu/mpc824x/cpu.c b/arch/powerpc/cpu/mpc824x/cpu.c
deleted file mode 100644
index eaa4e87..0000000
--- a/arch/powerpc/cpu/mpc824x/cpu.c
+++ /dev/null
@@ -1,262 +0,0 @@
-/*
- * (C) Copyright 2000 - 2002
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <mpc824x.h>
-#include <common.h>
-#include <command.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int checkcpu (void)
-{
- unsigned int pvr = get_pvr ();
- unsigned int version = pvr >> 16;
- unsigned char revision;
- ulong clock = gd->cpu_clk;
- char buf[32];
-
- puts ("CPU: ");
-
- switch (version) {
- case CPU_TYPE_8240:
- puts ("MPC8240");
- break;
-
- case CPU_TYPE_8245:
- puts ("MPC8245");
- break;
-
- default:
- return -1; /*not valid for this source */
- }
-
- CONFIG_READ_BYTE (REVID, revision);
-
- if (revision) {
- printf (" Revision %d.%d",
- (revision & 0xf0) >> 4,
- (revision & 0x0f));
- } else {
- return -1; /* no valid CPU revision info */
- }
-
- printf(" at %s MHz: ", strmhz(buf, clock));
-
- print_size(checkicache(), " I-Cache ");
- print_size(checkdcache(), " D-Cache\n");
-
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-/* L1 i-cache */
-
-int checkicache (void)
-{
- /*TODO*/
- return 128 * 4 * 32;
-};
-
-/* ------------------------------------------------------------------------- */
-/* L1 d-cache */
-
-int checkdcache (void)
-{
- /*TODO*/
- return 128 * 4 * 32;
-
-};
-
-/*------------------------------------------------------------------- */
-
-int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- ulong msr, addr;
-
- /* Interrupts and MMU off */
- __asm__ ("mtspr 81, 0");
-
- /* Interrupts and MMU off */
- __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
-
- msr &= ~0x1030;
- __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
-
- /*
- * Trying to execute the next instruction at a non-existing address
- * should cause a machine check, resulting in reset
- */
-#ifdef CONFIG_SYS_RESET_ADDRESS
- addr = CONFIG_SYS_RESET_ADDRESS;
-#else
- /*
- * note: when CONFIG_SYS_MONITOR_BASE points to a RAM address,
- * CONFIG_SYS_MONITOR_BASE - sizeof (ulong) is usually a valid
- * address. Better pick an address known to be invalid on
- * your system and assign it to CONFIG_SYS_RESET_ADDRESS.
- * "(ulong)-1" used to be a good choice for many systems...
- */
- addr = CONFIG_SYS_MONITOR_BASE - sizeof (ulong);
-#endif
- ((void (*)(void)) addr) ();
- return 1;
-
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Get timebase clock frequency (like cpu_clk in Hz)
- * This is the sys_logic_clk (memory bus) divided by 4
- */
-unsigned long get_tbclk (void)
-{
- return ((get_bus_freq (0) + 2L) / 4L);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * The MPC824x has an integrated PCI controller known as the MPC107.
- * The following are MPC107 Bridge Controller and PCI Support functions
- *
- */
-
-/*
- * This procedure reads a 32-bit address MPC107 register, and returns
- * a 32 bit value. It swaps the address to little endian before
- * writing it to config address, and swaps the value to big endian
- * before returning to the caller.
- */
-unsigned int mpc824x_mpc107_getreg (unsigned int regNum)
-{
- unsigned int temp;
-
- /* swap the addr. to little endian */
- *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum);
- temp = *(volatile unsigned int *) CHRP_REG_DATA;
- return PCISWAP (temp); /* swap the data upon return */
-}
-
-/*
- * This procedure writes a 32-bit address MPC107 register. It swaps
- * the address to little endian before writing it to config address.
- */
-
-void mpc824x_mpc107_setreg (unsigned int regNum, unsigned int regVal)
-{
- /* swap the addr. to little endian */
- *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum);
- *(volatile unsigned int *) CHRP_REG_DATA = PCISWAP (regVal);
- return;
-}
-
-
-/*
- * Write a byte (8 bits) to a memory location.
- */
-void mpc824x_mpc107_write8 (unsigned int addr, unsigned char data)
-{
- *(unsigned char *) addr = data;
- __asm__ ("sync");
-}
-
-/*
- * Write a word (16 bits) to a memory location after the value
- * has been byte swapped (big to little endian or vice versa)
- */
-
-void mpc824x_mpc107_write16 (unsigned int address, unsigned short data)
-{
- *(volatile unsigned short *) address = BYTE_SWAP_16_BIT (data);
- __asm__ ("sync");
-}
-
-/*
- * Write a long word (32 bits) to a memory location after the value
- * has been byte swapped (big to little endian or vice versa)
- */
-
-void mpc824x_mpc107_write32 (unsigned int address, unsigned int data)
-{
- *(volatile unsigned int *) address = LONGSWAP (data);
- __asm__ ("sync");
-}
-
-/*
- * Read a byte (8 bits) from a memory location.
- */
-unsigned char mpc824x_mpc107_read8 (unsigned int addr)
-{
- return *(volatile unsigned char *) addr;
-}
-
-
-/*
- * Read a word (16 bits) from a memory location, and byte swap the
- * value before returning to the caller.
- */
-unsigned short mpc824x_mpc107_read16 (unsigned int address)
-{
- unsigned short retVal;
-
- retVal = BYTE_SWAP_16_BIT (*(unsigned short *) address);
- return retVal;
-}
-
-
-/*
- * Read a long word (32 bits) from a memory location, and byte
- * swap the value before returning to the caller.
- */
-unsigned int mpc824x_mpc107_read32 (unsigned int address)
-{
- unsigned int retVal;
-
- retVal = LONGSWAP (*(unsigned int *) address);
- return (retVal);
-}
-
-
-/*
- * Read a register in the Embedded Utilities Memory Block address
- * space.
- * Input: regNum - register number + utility base address. Example,
- * the base address of EPIC is 0x40000, the register number
- * being passed is 0x40000+the address of the target register.
- * (See epic.h for register addresses).
- * Output: The 32 bit little endian value of the register.
- */
-
-unsigned int mpc824x_eummbar_read (unsigned int regNum)
-{
- unsigned int temp;
-
- temp = *(volatile unsigned int *) (EUMBBAR_VAL + regNum);
- temp = PCISWAP (temp);
- return temp;
-}
-
-
-/*
- * Write a value to a register in the Embedded Utilities Memory
- * Block address space.
- * Input: regNum - register number + utility base address. Example,
- * the base address of EPIC is 0x40000, the register
- * number is 0x40000+the address of the target register.
- * (See epic.h for register addresses).
- * regVal - value to be written to the register.
- */
-
-void mpc824x_eummbar_write (unsigned int regNum, unsigned int regVal)
-{
- *(volatile unsigned int *) (EUMBBAR_VAL + regNum) = PCISWAP (regVal);
- return;
-}
-
-/* ------------------------------------------------------------------------- */
diff --git a/arch/powerpc/cpu/mpc824x/cpu_init.c b/arch/powerpc/cpu/mpc824x/cpu_init.c
deleted file mode 100644
index 68d88e9..0000000
--- a/arch/powerpc/cpu/mpc824x/cpu_init.c
+++ /dev/null
@@ -1,311 +0,0 @@
-/*
- * (C) Copyright 2000
- * Rob Taylor. Flying Pig Systems. robt at flyingpig.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <mpc824x.h>
-
-#ifndef CONFIG_SYS_BANK0_ROW
-#define CONFIG_SYS_BANK0_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK1_ROW
-#define CONFIG_SYS_BANK1_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK2_ROW
-#define CONFIG_SYS_BANK2_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK3_ROW
-#define CONFIG_SYS_BANK3_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK4_ROW
-#define CONFIG_SYS_BANK4_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK5_ROW
-#define CONFIG_SYS_BANK5_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK6_ROW
-#define CONFIG_SYS_BANK6_ROW 0
-#endif
-#ifndef CONFIG_SYS_BANK7_ROW
-#define CONFIG_SYS_BANK7_ROW 0
-#endif
-#ifndef CONFIG_SYS_DBUS_SIZE2
-#define CONFIG_SYS_DBUS_SIZE2 0
-#endif
-
-/*
- * Breath some life into the CPU...
- *
- * Set up the memory map,
- * initialize a bunch of registers,
- */
-void
-cpu_init_f (void)
-{
- register unsigned long val;
- CONFIG_WRITE_HALFWORD(PCICR, 0x06); /* Bus Master, respond to PCI memory space acesses*/
-/* CONFIG_WRITE_HALFWORD(PCISR, 0xffff); */ /*reset PCISR*/
-
-#if defined(CONFIG_MUSENKI)
-/* Why is this here, you ask? Try, just try setting 0x8000
- * in PCIACR with CONFIG_WRITE_HALFWORD()
- * this one was a stumper, and we are annoyed
- */
-
-#define M_CONFIG_WRITE_HALFWORD( addr, data ) \
- __asm__ __volatile__(" \
- stw %2,0(%0)\n \
- sync\n \
- sth %3,2(%1)\n \
- sync\n \
- " \
- : /* no output */ \
- : "r" (CONFIG_ADDR), "r" (CONFIG_DATA), \
- "r" (PCISWAP(addr & ~3)), "r" (PCISWAP(data << 16)) \
- );
-
- M_CONFIG_WRITE_HALFWORD(PCIACR, 0x8000);
-#endif
-
- CONFIG_WRITE_BYTE(PCLSR, 0x8); /* set PCI cache line size */
- CONFIG_WRITE_BYTE (PLTR, 0x40); /* set PCI latency timer */
- /*
- * Note that although this bit is cleared after a hard reset, it
- * must be explicitly set and then cleared by software during
- * initialization in order to guarantee correct operation of the
- * DLL and the SDRAM_CLK[0:3] signals (if they are used).
- */
- CONFIG_READ_BYTE (AMBOR, val);
- CONFIG_WRITE_BYTE(AMBOR, val & 0xDF);
- CONFIG_WRITE_BYTE(AMBOR, val | 0x20);
- CONFIG_WRITE_BYTE(AMBOR, val & 0xDF);
-#ifdef CONFIG_MPC8245
- /* silicon bug 28 MPC8245 */
- CONFIG_READ_BYTE(AMBOR,val);
- CONFIG_WRITE_BYTE(AMBOR,val|0x1);
-
-#if 0
- /*
- * The following bug only affects older (XPC8245) processors.
- * DMA transfers initiated by external devices get corrupted due
- * to a hardware scheduling problem.
- *
- * The effect is:
- * when transferring X words, the first 32 words are transferred
- * OK, the next 3 x 32 words are 'old' data (from previous DMA)
- * while the rest of the X words is xferred fine.
- *
- * Disabling 3 of the 4 32 word hardware buffers solves the problem
- * with no significant performance loss.
- */
-
- CONFIG_READ_BYTE(PCMBCR,val);
- /* in order not to corrupt data which is being read over the PCI bus
- * with the PPC as slave, we need to reduce the number of PCMRBs to 1,
- * 4.11 in the processor user manual
- * */
-
-#if 1
- CONFIG_WRITE_BYTE(PCMBCR,(val|0xC0)); /* 1 PCMRB */
-#else
- CONFIG_WRITE_BYTE(PCMBCR,(val|0x80)); /* 2 PCMRBs */
- CONFIG_WRITE_BYTE(PCMBCR,(val|0x40)); /* 3 PCMRBs */
- /* default, 4 PCMRBs are used */
-#endif
-#endif
-#endif
-
- CONFIG_READ_WORD(PICR1, val);
-#if defined(CONFIG_MPC8240)
- CONFIG_WRITE_WORD( PICR1,
- (val & (PICR1_ADDRESS_MAP | PICR1_RCS0)) |
- PIRC1_MSK | PICR1_PROC_TYPE_603E |
- PICR1_FLASH_WR_EN | PICR1_MCP_EN |
- PICR1_CF_DPARK | PICR1_EN_PCS |
- PICR1_CF_APARK );
-#elif defined(CONFIG_MPC8245)
- CONFIG_WRITE_WORD( PICR1,
- (val & (PICR1_RCS0)) |
- PICR1_PROC_TYPE_603E |
- PICR1_FLASH_WR_EN | PICR1_MCP_EN |
- PICR1_CF_DPARK | PICR1_NO_BUSW_CK |
- PICR1_DEC| PICR1_CF_APARK | 0x10); /* 8245 UM says bit 4 must be set */
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
- CONFIG_READ_WORD(PICR2, val);
- val= val & ~ (PICR2_CF_SNOOP_WS_MASK | PICR2_CF_APHASE_WS_MASK); /*mask off waitstate bits*/
- val |= PICR2_CF_SNOOP_WS_1WS | PICR2_CF_APHASE_WS_1WS; /*1 wait state*/
- CONFIG_WRITE_WORD(PICR2, val);
-
- CONFIG_WRITE_WORD(EUMBBAR, CONFIG_SYS_EUMB_ADDR);
-#ifndef CONFIG_SYS_RAMBOOT
- CONFIG_WRITE_WORD(MCCR1, (CONFIG_SYS_ROMNAL << MCCR1_ROMNAL_SHIFT) |
- (CONFIG_SYS_BANK0_ROW) |
- (CONFIG_SYS_BANK1_ROW << MCCR1_BANK1ROW_SHIFT) |
- (CONFIG_SYS_BANK2_ROW << MCCR1_BANK2ROW_SHIFT) |
- (CONFIG_SYS_BANK3_ROW << MCCR1_BANK3ROW_SHIFT) |
- (CONFIG_SYS_BANK4_ROW << MCCR1_BANK4ROW_SHIFT) |
- (CONFIG_SYS_BANK5_ROW << MCCR1_BANK5ROW_SHIFT) |
- (CONFIG_SYS_BANK6_ROW << MCCR1_BANK6ROW_SHIFT) |
- (CONFIG_SYS_BANK7_ROW << MCCR1_BANK7ROW_SHIFT) |
- (CONFIG_SYS_ROMFAL << MCCR1_ROMFAL_SHIFT));
-#endif
-
-#if defined(CONFIG_SYS_ASRISE) && defined(CONFIG_SYS_ASFALL)
- CONFIG_WRITE_WORD(MCCR2, CONFIG_SYS_REFINT << MCCR2_REFINT_SHIFT |
- CONFIG_SYS_ASRISE << MCCR2_ASRISE_SHIFT |
- CONFIG_SYS_ASFALL << MCCR2_ASFALL_SHIFT);
-#else
- CONFIG_WRITE_WORD(MCCR2, CONFIG_SYS_REFINT << MCCR2_REFINT_SHIFT);
-#endif
-
-#if defined(CONFIG_MPC8240)
- CONFIG_WRITE_WORD(MCCR3,
- (((CONFIG_SYS_BSTOPRE & 0x003c) >> 2) << MCCR3_BSTOPRE2TO5_SHIFT) |
- (CONFIG_SYS_REFREC << MCCR3_REFREC_SHIFT) |
- (CONFIG_SYS_RDLAT << MCCR3_RDLAT_SHIFT));
-#elif defined(CONFIG_MPC8245)
- CONFIG_WRITE_WORD(MCCR3,
- (((CONFIG_SYS_BSTOPRE & 0x003c) >> 2) << MCCR3_BSTOPRE2TO5_SHIFT) |
- (CONFIG_SYS_REFREC << MCCR3_REFREC_SHIFT));
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
-/* this is gross. We think these should all be the same, and various boards
- * should define CONFIG_SYS_ACTORW to 0 if they don't want to set it, or even, if
- * its not set, we define it to zero in this file
- */
-#if defined(CONFIG_CU824)
- CONFIG_WRITE_WORD(MCCR4,
- (CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) |
- (CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) |
- MCCR4_BIT21 |
- (CONFIG_SYS_REGISTERD_TYPE_BUFFER ? MCCR4_REGISTERED: 0) |
- ((CONFIG_SYS_BSTOPRE & 0x0003) <<MCCR4_BSTOPRE0TO1_SHIFT ) |
- (((CONFIG_SYS_SDMODE_CAS_LAT <<4) | (CONFIG_SYS_SDMODE_WRAP <<3) |
- CONFIG_SYS_SDMODE_BURSTLEN) << MCCR4_SDMODE_SHIFT) |
- (CONFIG_SYS_ACTORW << MCCR4_ACTTORW_SHIFT) |
- (((CONFIG_SYS_BSTOPRE & 0x03c0) >> 6) << MCCR4_BSTOPRE6TO9_SHIFT));
-#elif defined(CONFIG_MPC8240)
- CONFIG_WRITE_WORD(MCCR4,
- (CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) |
- (CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) |
- MCCR4_BIT21 |
- (CONFIG_SYS_REGISTERD_TYPE_BUFFER ? MCCR4_REGISTERED: 0) |
- ((CONFIG_SYS_BSTOPRE & 0x0003) <<MCCR4_BSTOPRE0TO1_SHIFT ) |
- (((CONFIG_SYS_SDMODE_CAS_LAT <<4) | (CONFIG_SYS_SDMODE_WRAP <<3) |
- (CONFIG_SYS_SDMODE_BURSTLEN)) <<MCCR4_SDMODE_SHIFT) |
- (((CONFIG_SYS_BSTOPRE & 0x03c0) >> 6) <<MCCR4_BSTOPRE6TO9_SHIFT ));
-#elif defined(CONFIG_MPC8245)
- CONFIG_READ_WORD(MCCR1, val);
- val &= MCCR1_DBUS_SIZE0; /* test for 64-bit mem bus */
-
- CONFIG_WRITE_WORD(MCCR4,
- (CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) |
- (CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) |
- (CONFIG_SYS_EXTROM ? MCCR4_EXTROM : 0) |
- (CONFIG_SYS_REGDIMM ? MCCR4_REGDIMM : 0) |
- (CONFIG_SYS_REGISTERD_TYPE_BUFFER ? MCCR4_REGISTERED: 0) |
- ((CONFIG_SYS_BSTOPRE & 0x0003) <<MCCR4_BSTOPRE0TO1_SHIFT ) |
- (CONFIG_SYS_DBUS_SIZE2 << MCCR4_DBUS_SIZE2_SHIFT) |
- (((CONFIG_SYS_SDMODE_CAS_LAT <<4) | (CONFIG_SYS_SDMODE_WRAP <<3) |
- (val ? 2 : 3)) << MCCR4_SDMODE_SHIFT) |
- (CONFIG_SYS_ACTORW << MCCR4_ACTTORW_SHIFT) |
- (((CONFIG_SYS_BSTOPRE & 0x03c0) >> 6) <<MCCR4_BSTOPRE6TO9_SHIFT ));
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
- CONFIG_WRITE_WORD(MSAR1,
- ( (CONFIG_SYS_BANK0_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) |
- (((CONFIG_SYS_BANK1_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK2_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK3_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(EMSAR1,
- ( (CONFIG_SYS_BANK0_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
- (((CONFIG_SYS_BANK1_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK2_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK3_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(MSAR2,
- ( (CONFIG_SYS_BANK4_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) |
- (((CONFIG_SYS_BANK5_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK6_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK7_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(EMSAR2,
- ( (CONFIG_SYS_BANK4_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
- (((CONFIG_SYS_BANK5_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK6_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK7_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(MEAR1,
- ( (CONFIG_SYS_BANK0_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) |
- (((CONFIG_SYS_BANK1_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK2_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK3_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(EMEAR1,
- ( (CONFIG_SYS_BANK0_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
- (((CONFIG_SYS_BANK1_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK2_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK3_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(MEAR2,
- ( (CONFIG_SYS_BANK4_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) |
- (((CONFIG_SYS_BANK5_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK6_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK7_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24));
- CONFIG_WRITE_WORD(EMEAR2,
- ( (CONFIG_SYS_BANK4_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
- (((CONFIG_SYS_BANK5_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) |
- (((CONFIG_SYS_BANK6_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) |
- (((CONFIG_SYS_BANK7_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24));
-
- CONFIG_WRITE_BYTE(ODCR, CONFIG_SYS_ODCR);
-#ifdef CONFIG_SYS_DLL_MAX_DELAY
- CONFIG_WRITE_BYTE(MIOCR1, CONFIG_SYS_DLL_MAX_DELAY); /* needed to make DLL lock */
-#endif
-#if defined(CONFIG_SYS_DLL_EXTEND) && defined(CONFIG_SYS_PCI_HOLD_DEL)
- CONFIG_WRITE_BYTE(PMCR2, CONFIG_SYS_DLL_EXTEND | CONFIG_SYS_PCI_HOLD_DEL);
-#endif
-#if defined(MIOCR2) && defined(CONFIG_SYS_SDRAM_DSCD)
- CONFIG_WRITE_BYTE(MIOCR2, CONFIG_SYS_SDRAM_DSCD); /* change memory input */
-#endif /* setup & hold time */
-
- CONFIG_WRITE_BYTE(MBER,
- CONFIG_SYS_BANK0_ENABLE |
- (CONFIG_SYS_BANK1_ENABLE << 1) |
- (CONFIG_SYS_BANK2_ENABLE << 2) |
- (CONFIG_SYS_BANK3_ENABLE << 3) |
- (CONFIG_SYS_BANK4_ENABLE << 4) |
- (CONFIG_SYS_BANK5_ENABLE << 5) |
- (CONFIG_SYS_BANK6_ENABLE << 6) |
- (CONFIG_SYS_BANK7_ENABLE << 7));
-
-#ifdef CONFIG_SYS_PGMAX
- CONFIG_WRITE_BYTE(MPMR, CONFIG_SYS_PGMAX);
-#endif
-
- /* ! Wait 200us before initialize other registers */
- /*FIXME: write a decent udelay wait */
- __asm__ __volatile__(
- " mtctr %0 \n \
- 0: bdnz 0b\n"
- :
- : "r" (0x10000));
-
- CONFIG_READ_WORD(MCCR1, val);
- CONFIG_WRITE_WORD(MCCR1, val | MCCR1_MEMGO); /* set memory access going */
- __asm__ __volatile__("eieio");
-}
-
-/*
- * initialize higher level parts of CPU like time base and timers
- */
-int cpu_init_r (void)
-{
- return (0);
-}
diff --git a/arch/powerpc/cpu/mpc824x/drivers/epic.h b/arch/powerpc/cpu/mpc824x/drivers/epic.h
deleted file mode 100644
index 2803f63..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/epic.h
+++ /dev/null
@@ -1 +0,0 @@
-#include "epic/epic.h"
diff --git a/arch/powerpc/cpu/mpc824x/drivers/epic/README b/arch/powerpc/cpu/mpc824x/drivers/epic/README
deleted file mode 100644
index 5798996..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/epic/README
+++ /dev/null
@@ -1,102 +0,0 @@
-CONTENT:
-
- epic.h
- epic1.c
- epic2.s
-
-WHAT ARE THESE FILES:
-
-These files contain MPC8240 (Kahlua) EPIC
-driver routines. The driver routines are not
-written for any specific operating system.
-They serves the purpose of code sample, and
-jump-start for using the MPC8240 EPIC unit.
-
-For the reason of correctness of C language
-syntax, these files are compiled by Metaware
-C compiler and assembler.
-
-ENDIAN NOTATION:
-
-The algorithm is designed for big-endian mode,
-software is responsible for byte swapping.
-
-USAGE:
-
-1. The host system that is running on MPC8240
- shall link the files listed here. The memory
- location of driver routines shall take into
- account of that driver routines need to run
- in supervisor mode and they process external
- interrupts.
-
- The routine epic_exception shall be called by
- exception vector at location 0x500, i.e.,
- 603e core external exception vector.
-
-2. The host system is responsible for configuring
- the MPC8240 including Embedded Utilities Memory
- Block. All EPIC driver functions require the
- content of Embedded Utilities Memory Block
- Base Address Register, EUMBBAR, as the first
- parameter.
-
-3. Before EPIC unit of MPC8240 can be used,
- initialize EPIC unit by calling epicInit
- with the corresponding parameters.
-
- The initialization shall disable the 603e
- core External Exception by calling CoreExtIntDisable( ).
- Next, call epicInit( ). Last, enable the 603e core
- External Exception by calling CoreExtIntEnable( ).
-
-4. After EPIC unit has been successfully initialized,
- epicIntSourceSet( ) shall be used to register each
- external interrupt source. Anytime, an external
- interrupt source can be disabled or enabled by
- calling corresponding function, epicIntDisable( ),
- or epicIntEnable( ).
-
- Global Timers' resource, base count and frequency,
- can be changed by calling epicTmFrequencySet( )
- and epicTmBaseSet( ).
-
- To stop counting a specific global timer, use
- the function, epicTmInhibit while epicTmEnable
- can be used to start counting a timer.
-
-5. To mask a set of external interrupts that are
- are certain level below, epicIntPrioritySet( )
- can be used. For example, if the processor's
- current task priority register is set to 0x7,
- only interrupts of priority 0x8 or higher will
- be passed to the processor.
-
- Be careful when using this function. It may
- corrupt the current interrupt pending, selector,
- and request registers, resulting an invalid vetor.
-
- After enabling an interrupt, disable it may also
- cause an invalid vector. User may consider using
- the spurious vector interrupt service routine to
- handle this case.
-
-6. The EPIC driver routines contains a set
- of utilities, Set and Get, for host system
- to query and modify the desired EPIC source
- registers.
-
-7. Each external interrupt source shall register
- its interrupt service routine. The routine
- shall contain all interrupt source specific
- processes and keep as short as possible.
-
- Special customized end of interrupt routine
- is optional. If it is needed, it shall contain
- the external interrupt source specific end of
- interrupt process.
-
- External interrupt exception vector@0x500
- shall always call the epicEOI just before
- rfi instruction. Refer to the routine,
- epic_exception, for a code sample.
diff --git a/arch/powerpc/cpu/mpc824x/drivers/epic/epic.h b/arch/powerpc/cpu/mpc824x/drivers/epic/epic.h
deleted file mode 100644
index 58f81c5..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/epic/epic.h
+++ /dev/null
@@ -1,163 +0,0 @@
-/*********************************************************************
- * mpc8240epic.h - EPIC module of the MPC8240 micro-controller
- *
- * Copyrigh 1999 Motorola Inc.
- *
- * Modification History:
- * =====================
- * 01a,04Feb99,My Created.
- * 15Nov200, robt -modified to use in U-Boot
- *
-*/
-
-#ifndef __INCEPICh
-#define __INCEPICh
-
-#define ULONG unsigned long
-#define MAXVEC 20
-#define MAXIRQ 5 /* IRQs */
-#define EPIC_DIRECT_IRQ 0 /* Direct interrupt type */
-
-/* EPIC register addresses */
-
-#define EPIC_EUMBBAR 0x40000 /* EUMBBAR of EPIC */
-#define EPIC_FEATURES_REG (EPIC_EUMBBAR + 0x01000)/* Feature reporting */
-#define EPIC_GLOBAL_REG (EPIC_EUMBBAR + 0x01020)/* Global config. */
-#define EPIC_INT_CONF_REG (EPIC_EUMBBAR + 0x01030)/* Interrupt config. */
-#define EPIC_VENDOR_ID_REG (EPIC_EUMBBAR + 0x01080)/* Vendor id */
-#define EPIC_PROC_INIT_REG (EPIC_EUMBBAR + 0x01090)/* Processor init. */
-#define EPIC_SPUR_VEC_REG (EPIC_EUMBBAR + 0x010e0)/* Spurious vector */
-#define EPIC_TM_FREQ_REG (EPIC_EUMBBAR + 0x010f0)/* Timer Frequency */
-
-#define EPIC_TM0_CUR_COUNT_REG (EPIC_EUMBBAR + 0x01100)/* Gbl TM0 Cur. Count*/
-#define EPIC_TM0_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01110)/* Gbl TM0 Base Count*/
-#define EPIC_TM0_VEC_REG (EPIC_EUMBBAR + 0x01120)/* Gbl TM0 Vector Pri*/
-#define EPIC_TM0_DES_REG (EPIC_EUMBBAR + 0x01130)/* Gbl TM0 Dest. */
-
-#define EPIC_TM1_CUR_COUNT_REG (EPIC_EUMBBAR + 0x01140)/* Gbl TM1 Cur. Count*/
-#define EPIC_TM1_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01150)/* Gbl TM1 Base Count*/
-#define EPIC_TM1_VEC_REG (EPIC_EUMBBAR + 0x01160)/* Gbl TM1 Vector Pri*/
-#define EPIC_TM1_DES_REG (EPIC_EUMBBAR + 0x01170)/* Gbl TM1 Dest. */
-
-#define EPIC_TM2_CUR_COUNT_REG (EPIC_EUMBBAR + 0x01180)/* Gbl TM2 Cur. Count*/
-#define EPIC_TM2_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01190)/* Gbl TM2 Base Count*/
-#define EPIC_TM2_VEC_REG (EPIC_EUMBBAR + 0x011a0)/* Gbl TM2 Vector Pri*/
-#define EPIC_TM2_DES_REG (EPIC_EUMBBAR + 0x011b0)/* Gbl TM2 Dest */
-
-#define EPIC_TM3_CUR_COUNT_REG (EPIC_EUMBBAR + 0x011c0)/* Gbl TM3 Cur. Count*/
-#define EPIC_TM3_BASE_COUNT_REG (EPIC_EUMBBAR + 0x011d0)/* Gbl TM3 Base Count*/
-#define EPIC_TM3_VEC_REG (EPIC_EUMBBAR + 0x011e0)/* Gbl TM3 Vector Pri*/
-#define EPIC_TM3_DES_REG (EPIC_EUMBBAR + 0x011f0)/* Gbl TM3 Dest. */
-
-#define EPIC_EX_INT0_VEC_REG (EPIC_EUMBBAR + 0x10200)/* Ext. Int. Sr0 Des */
-#define EPIC_EX_INT0_DES_REG (EPIC_EUMBBAR + 0x10210)/* Ext. Int. Sr0 Vect*/
-#define EPIC_EX_INT1_VEC_REG (EPIC_EUMBBAR + 0x10220)/* Ext. Int. Sr1 Des */
-#define EPIC_EX_INT1_DES_REG (EPIC_EUMBBAR + 0x10230)/* Ext. Int. Sr1 Vect*/
-#define EPIC_EX_INT2_VEC_REG (EPIC_EUMBBAR + 0x10240)/* Ext. Int. Sr2 Des */
-#define EPIC_EX_INT2_DES_REG (EPIC_EUMBBAR + 0x10250)/* Ext. Int. Sr2 Vect*/
-#define EPIC_EX_INT3_VEC_REG (EPIC_EUMBBAR + 0x10260)/* Ext. Int. Sr3 Des */
-#define EPIC_EX_INT3_DES_REG (EPIC_EUMBBAR + 0x10270)/* Ext. Int. Sr3 Vect*/
-#define EPIC_EX_INT4_VEC_REG (EPIC_EUMBBAR + 0x10280)/* Ext. Int. Sr4 Des */
-#define EPIC_EX_INT4_DES_REG (EPIC_EUMBBAR + 0x10290)/* Ext. Int. Sr4 Vect*/
-
-#define EPIC_SR_INT0_VEC_REG (EPIC_EUMBBAR + 0x10200)/* Sr. Int. Sr0 Des */
-#define EPIC_SR_INT0_DES_REG (EPIC_EUMBBAR + 0x10210)/* Sr. Int. Sr0 Vect */
-#define EPIC_SR_INT1_VEC_REG (EPIC_EUMBBAR + 0x10220)/* Sr. Int. Sr1 Des */
-#define EPIC_SR_INT1_DES_REG (EPIC_EUMBBAR + 0x10230)/* Sr. Int. Sr1 Vect.*/
-#define EPIC_SR_INT2_VEC_REG (EPIC_EUMBBAR + 0x10240)/* Sr. Int. Sr2 Des */
-#define EPIC_SR_INT2_DES_REG (EPIC_EUMBBAR + 0x10250)/* Sr. Int. Sr2 Vect.*/
-#define EPIC_SR_INT3_VEC_REG (EPIC_EUMBBAR + 0x10260)/* Sr. Int. Sr3 Des */
-#define EPIC_SR_INT3_DES_REG (EPIC_EUMBBAR + 0x10270)/* Sr. Int. Sr3 Vect.*/
-#define EPIC_SR_INT4_VEC_REG (EPIC_EUMBBAR + 0x10280)/* Sr. Int. Sr4 Des */
-#define EPIC_SR_INT4_DES_REG (EPIC_EUMBBAR + 0x10290)/* Sr. Int. Sr4 Vect.*/
-
-#define EPIC_SR_INT5_VEC_REG (EPIC_EUMBBAR + 0x102a0)/* Sr. Int. Sr5 Des */
-#define EPIC_SR_INT5_DES_REG (EPIC_EUMBBAR + 0x102b0)/* Sr. Int. Sr5 Vect.*/
-#define EPIC_SR_INT6_VEC_REG (EPIC_EUMBBAR + 0x102c0)/* Sr. Int. Sr6 Des */
-#define EPIC_SR_INT6_DES_REG (EPIC_EUMBBAR + 0x102d0)/* Sr. Int. Sr6 Vect.*/
-#define EPIC_SR_INT7_VEC_REG (EPIC_EUMBBAR + 0x102e0)/* Sr. Int. Sr7 Des */
-#define EPIC_SR_INT7_DES_REG (EPIC_EUMBBAR + 0x102f0)/* Sr. Int. Sr7 Vect.*/
-#define EPIC_SR_INT8_VEC_REG (EPIC_EUMBBAR + 0x10300)/* Sr. Int. Sr8 Des */
-#define EPIC_SR_INT8_DES_REG (EPIC_EUMBBAR + 0x10310)/* Sr. Int. Sr8 Vect.*/
-#define EPIC_SR_INT9_VEC_REG (EPIC_EUMBBAR + 0x10320)/* Sr. Int. Sr9 Des */
-#define EPIC_SR_INT9_DES_REG (EPIC_EUMBBAR + 0x10330)/* Sr. Int. Sr9 Vect.*/
-
-#define EPIC_SR_INT10_VEC_REG (EPIC_EUMBBAR + 0x10340)/* Sr. Int. Sr10 Des */
-#define EPIC_SR_INT10_DES_REG (EPIC_EUMBBAR + 0x10350)/* Sr. Int. Sr10 Vect*/
-#define EPIC_SR_INT11_VEC_REG (EPIC_EUMBBAR + 0x10360)/* Sr. Int. Sr11 Des */
-#define EPIC_SR_INT11_DES_REG (EPIC_EUMBBAR + 0x10370)/* Sr. Int. Sr11 Vect*/
-#define EPIC_SR_INT12_VEC_REG (EPIC_EUMBBAR + 0x10380)/* Sr. Int. Sr12 Des */
-#define EPIC_SR_INT12_DES_REG (EPIC_EUMBBAR + 0x10390)/* Sr. Int. Sr12 Vect*/
-#define EPIC_SR_INT13_VEC_REG (EPIC_EUMBBAR + 0x103a0)/* Sr. Int. Sr13 Des */
-#define EPIC_SR_INT13_DES_REG (EPIC_EUMBBAR + 0x103b0)/* Sr. Int. Sr13 Vect*/
-#define EPIC_SR_INT14_VEC_REG (EPIC_EUMBBAR + 0x103c0)/* Sr. Int. Sr14 Des */
-#define EPIC_SR_INT14_DES_REG (EPIC_EUMBBAR + 0x103d0)/* Sr. Int. Sr14 Vect*/
-#define EPIC_SR_INT15_VEC_REG (EPIC_EUMBBAR + 0x103e0)/* Sr. Int. Sr15 Des */
-#define EPIC_SR_INT15_DES_REG (EPIC_EUMBBAR + 0x103f0)/* Sr. Int. Sr15 Vect*/
-
-#define EPIC_I2C_INT_VEC_REG (EPIC_EUMBBAR + 0x11020)/* I2C Int. Vect Pri.*/
-#define EPIC_I2C_INT_DES_REG (EPIC_EUMBBAR + 0x11030)/* I2C Int. Dest */
-#define EPIC_DMA0_INT_VEC_REG (EPIC_EUMBBAR + 0x11040)/* DMA0 Int. Vect Pri*/
-#define EPIC_DMA0_INT_DES_REG (EPIC_EUMBBAR + 0x11050)/* DMA0 Int. Dest */
-#define EPIC_DMA1_INT_VEC_REG (EPIC_EUMBBAR + 0x11060)/* DMA1 Int. Vect Pri*/
-#define EPIC_DMA1_INT_DES_REG (EPIC_EUMBBAR + 0x11070)/* DMA1 Int. Dest */
-#define EPIC_MSG_INT_VEC_REG (EPIC_EUMBBAR + 0x110c0)/* Msg Int. Vect Pri*/
-#define EPIC_MSG_INT_DES_REG (EPIC_EUMBBAR + 0x110d0)/* Msg Int. Dest */
-
-#define EPIC_PROC_CTASK_PRI_REG (EPIC_EUMBBAR + 0x20080)/* Proc. current task*/
-#define EPIC_PROC_INT_ACK_REG (EPIC_EUMBBAR + 0x200a0)/* Int. acknowledge */
-#define EPIC_PROC_EOI_REG (EPIC_EUMBBAR + 0x200b0)/* End of interrupt */
-
-#define EPIC_VEC_PRI_MASK 0x80000000 /* Mask Interrupt bit in IVPR */
-#define EPIC_VEC_PRI_DFLT_PRI 8 /* Interrupt Priority in IVPR */
-
-/* Error code */
-
-#define OK 0
-#define ERROR -1
-
-/* function prototypes */
-
-void epicVendorId( unsigned int *step,
- unsigned int *devId,
- unsigned int *venId
- );
-void epicFeatures( unsigned int *noIRQs,
- unsigned int *noCPUs,
- unsigned int *VerId );
-extern void epicInit( unsigned int IRQType, unsigned int clkRatio);
-ULONG sysEUMBBARRead ( ULONG regNum );
-void sysEUMBBARWrite ( ULONG regNum, ULONG regVal);
-extern void epicTmFrequencySet( unsigned int frq );
-extern unsigned int epicTmFrequencyGet(void);
-extern unsigned int epicTmBaseSet( ULONG srcAddr,
- unsigned int cnt,
- unsigned int inhibit );
-extern unsigned int epicTmBaseGet ( ULONG srcAddr, unsigned int *val );
-extern unsigned int epicTmCountGet( ULONG srcAddr, unsigned int *val );
-extern unsigned int epicTmInhibit( unsigned int timer );
-extern unsigned int epicTmEnable( ULONG srcAdr );
-extern void CoreExtIntEnable(void); /* Enable 603e external interrupts */
-extern void CoreExtIntDisable(void); /* Disable 603e external interrupts */
-extern unsigned char epicIntTaskGet(void);
-extern void epicIntTaskSet( unsigned char val );
-extern unsigned int epicIntAck(void);
-extern void epicSprSet( unsigned int eumbbar, unsigned char );
-extern void epicConfigGet( unsigned int *clkRatio,
- unsigned int *serEnable );
-extern void SrcVecTableInit(void);
-extern unsigned int epicModeGet(void);
-extern void epicIntEnable(int Vect);
-extern void epicIntDisable(int Vect);
-extern int epicIntSourceConfig(int Vect, int Polarity, int Sense, int Prio);
-extern unsigned int epicIntAck(void);
-extern void epicEOI(void);
-extern int epicCurTaskPrioSet(int Vect);
-
-struct SrcVecTable
- {
- ULONG srcAddr;
- char srcName[40];
- };
-
-#endif /* EPIC_H */
diff --git a/arch/powerpc/cpu/mpc824x/drivers/epic/epic1.c b/arch/powerpc/cpu/mpc824x/drivers/epic/epic1.c
deleted file mode 100644
index ecbb42d..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/epic/epic1.c
+++ /dev/null
@@ -1,517 +0,0 @@
-/**************************************************
- *
- * copyright @ motorola, 1999
- *
- *************************************************/
-#include <mpc824x.h>
-#include <common.h>
-#include "epic.h"
-
-
-#define PRINT(format, args...) printf(format , ## args)
-
-typedef void (*VOIDFUNCPTR) (void); /* ptr to function returning void */
-struct SrcVecTable SrcVecTable[MAXVEC] = /* Addr/Vector cross-reference tbl */
- {
- { EPIC_EX_INT0_VEC_REG, "External Direct/Serial Source 0"},
- { EPIC_EX_INT1_VEC_REG, "External Direct/Serial Source 1"},
- { EPIC_EX_INT2_VEC_REG, "External Direct/Serial Source 2"},
- { EPIC_EX_INT3_VEC_REG, "External Direct/Serial Source 3"},
- { EPIC_EX_INT4_VEC_REG, "External Direct/Serial Source 4"},
-
- { EPIC_SR_INT5_VEC_REG, "External Serial Source 5"},
- { EPIC_SR_INT6_VEC_REG, "External Serial Source 6"},
- { EPIC_SR_INT7_VEC_REG, "External Serial Source 7"},
- { EPIC_SR_INT8_VEC_REG, "External Serial Source 8"},
- { EPIC_SR_INT9_VEC_REG, "External Serial Source 9"},
- { EPIC_SR_INT10_VEC_REG, "External Serial Source 10"},
- { EPIC_SR_INT11_VEC_REG, "External Serial Source 11"},
- { EPIC_SR_INT12_VEC_REG, "External Serial Source 12"},
- { EPIC_SR_INT13_VEC_REG, "External Serial Source 13"},
- { EPIC_SR_INT14_VEC_REG, "External Serial Source 14"},
- { EPIC_SR_INT15_VEC_REG, "External Serial Source 15"},
-
- { EPIC_I2C_INT_VEC_REG, "Internal I2C Source"},
- { EPIC_DMA0_INT_VEC_REG, "Internal DMA0 Source"},
- { EPIC_DMA1_INT_VEC_REG, "Internal DMA1 Source"},
- { EPIC_MSG_INT_VEC_REG, "Internal Message Source"},
- };
-
-VOIDFUNCPTR intVecTbl[MAXVEC]; /* Interrupt vector table */
-
-
-/****************************************************************************
-* epicInit - Initialize the EPIC registers
-*
-* This routine resets the Global Configuration Register, thus it:
-* - Disables all interrupts
-* - Sets epic registers to reset values
-* - Sets the value of the Processor Current Task Priority to the
-* highest priority (0xF).
-* epicInit then sets the EPIC operation mode to Mixed Mode (vs. Pass
-* Through or 8259 compatible mode).
-*
-* If IRQType (input) is Direct IRQs:
-* - IRQType is written to the SIE bit of the EPIC Interrupt
-* Configuration register (ICR).
-* - clkRatio is ignored.
-* If IRQType is Serial IRQs:
-* - both IRQType and clkRatio will be written to the ICR register
-*/
-
-void epicInit
- (
- unsigned int IRQType, /* Direct or Serial */
- unsigned int clkRatio /* Clk Ratio for Serial IRQs */
- )
- {
- ULONG tmp;
-
- tmp = sysEUMBBARRead(EPIC_GLOBAL_REG);
- tmp |= 0xa0000000; /* Set the Global Conf. register */
- sysEUMBBARWrite(EPIC_GLOBAL_REG, tmp);
- /*
- * Wait for EPIC to reset - CLH
- */
- while( (sysEUMBBARRead(EPIC_GLOBAL_REG) & 0x80000000) == 1);
- sysEUMBBARWrite(EPIC_GLOBAL_REG, 0x20000000);
- tmp = sysEUMBBARRead(EPIC_INT_CONF_REG); /* Read interrupt conf. reg */
-
- if (IRQType == EPIC_DIRECT_IRQ) /* direct mode */
- sysEUMBBARWrite(EPIC_INT_CONF_REG, tmp & 0xf7ffffff);
- else /* Serial mode */
- {
- tmp = (clkRatio << 28) | 0x08000000; /* Set clock ratio */
- sysEUMBBARWrite(EPIC_INT_CONF_REG, tmp);
- }
-
- while (epicIntAck() != 0xff) /* Clear all pending interrupts */
- epicEOI();
-}
-
-/****************************************************************************
- * epicIntEnable - Enable an interrupt source
- *
- * This routine clears the mask bit of an external, an internal or
- * a Timer register to enable the interrupt.
- *
- * RETURNS: None
- */
-void epicIntEnable(int intVec)
-{
- ULONG tmp;
- ULONG srAddr;
-
- srAddr = SrcVecTable[intVec].srcAddr; /* Retrieve src Vec/Prio register */
- tmp = sysEUMBBARRead(srAddr);
- tmp &= ~EPIC_VEC_PRI_MASK; /* Clear the mask bit */
- tmp |= (EPIC_VEC_PRI_DFLT_PRI << 16); /* Set priority to Default - CLH */
- tmp |= intVec; /* Set Vector number */
- sysEUMBBARWrite(srAddr, tmp);
-
- return;
- }
-
-/****************************************************************************
- * epicIntDisable - Disable an interrupt source
- *
- * This routine sets the mask bit of an external, an internal or
- * a Timer register to disable the interrupt.
- *
- * RETURNS: OK or ERROR
- *
- */
-
-void epicIntDisable
- (
- int intVec /* Interrupt vector number */
- )
- {
-
- ULONG tmp, srAddr;
-
- srAddr = SrcVecTable[intVec].srcAddr;
- tmp = sysEUMBBARRead(srAddr);
- tmp |= 0x80000000; /* Set the mask bit */
- sysEUMBBARWrite(srAddr, tmp);
- return;
- }
-
-/****************************************************************************
- * epicIntSourceConfig - Set properties of an interrupt source
- *
- * This function sets interrupt properites (Polarity, Sense, Interrupt
- * Prority, and Interrupt Vector) of an Interrupt Source. The properties
- * can be set when the current source is not in-request or in-service,
- * which is determined by the Activity bit. This routine return ERROR
- * if the the Activity bit is 1 (in-request or in-service).
- *
- * This function assumes that the Source Vector/Priority register (input)
- * is a valid address.
- *
- * RETURNS: OK or ERROR
- */
-
-int epicIntSourceConfig
- (
- int Vect, /* interrupt source vector number */
- int Polarity, /* interrupt source polarity */
- int Sense, /* interrupt source Sense */
- int Prio /* interrupt source priority */
- )
-
- {
- ULONG tmp, newVal;
- ULONG actBit, srAddr;
-
- srAddr = SrcVecTable[Vect].srcAddr;
- tmp = sysEUMBBARRead(srAddr);
- actBit = (tmp & 40000000) >> 30; /* retrieve activity bit - bit 30 */
- if (actBit == 1)
- return ERROR;
-
- tmp &= 0xff30ff00; /* Erase previously set P,S,Prio,Vector bits */
- newVal = (Polarity << 23) | (Sense << 22) | (Prio << 16) | Vect;
- sysEUMBBARWrite(srAddr, tmp | newVal );
- return (OK);
- }
-
-/****************************************************************************
- * epicIntAck - acknowledge an interrupt
- *
- * This function reads the Interrupt acknowldge register and return
- * the vector number of the highest pending interrupt.
- *
- * RETURNS: Interrupt Vector number.
- */
-
-unsigned int epicIntAck(void)
-{
- return(sysEUMBBARRead( EPIC_PROC_INT_ACK_REG ));
-}
-
-/****************************************************************************
- * epicEOI - signal an end of interrupt
- *
- * This function writes 0x0 to the EOI register to signal end of interrupt.
- * It is usually called after an interrupt routine is served.
- *
- * RETURNS: None
- */
-
-void epicEOI(void)
- {
- sysEUMBBARWrite(EPIC_PROC_EOI_REG, 0x0);
- }
-
-/****************************************************************************
- * epicCurTaskPrioSet - sets the priority of the Processor Current Task
- *
- * This function should be called after epicInit() to lower the priority
- * of the processor current task.
- *
- * RETURNS: OK or ERROR
- */
-
-int epicCurTaskPrioSet
- (
- int prioNum /* New priority value */
- )
- {
-
- if ( (prioNum < 0) || (prioNum > 0xF))
- return ERROR;
- sysEUMBBARWrite(EPIC_PROC_CTASK_PRI_REG, prioNum);
- return OK;
- }
-
-
-/************************************************************************
- * function: epicIntTaskGet
- *
- * description: Get value of processor current interrupt task priority register
- *
- * note:
- ***********************************************************************/
-unsigned char epicIntTaskGet()
-{
- /* get the interrupt task priority register */
- ULONG reg;
- unsigned char rec;
-
- reg = sysEUMBBARRead( EPIC_PROC_CTASK_PRI_REG );
- rec = ( reg & 0x0F );
- return rec;
-}
-
-
-/**************************************************************
- * function: epicISR
- *
- * description: EPIC service routine called by the core exception
- * at 0x500
- *
- * note:
- **************************************************************/
-unsigned int epicISR(void)
-{
- return 0;
-}
-
-
-/************************************************************
- * function: epicModeGet
- *
- * description: query EPIC mode, return 0 if pass through mode
- * return 1 if mixed mode
- *
- * note:
- *************************************************************/
-unsigned int epicModeGet(void)
-{
- ULONG val;
-
- val = sysEUMBBARRead( EPIC_GLOBAL_REG );
- return (( val & 0x20000000 ) >> 29);
-}
-
-
-/*********************************************
- * function: epicConfigGet
- *
- * description: Get the EPIC interrupt Configuration
- * return 0 if not error, otherwise return 1
- *
- * note:
- ********************************************/
-void epicConfigGet( unsigned int *clkRatio, unsigned int *serEnable)
-{
- ULONG val;
-
- val = sysEUMBBARRead( EPIC_INT_CONF_REG );
- *clkRatio = ( val & 0x70000000 ) >> 28;
- *serEnable = ( val & 0x8000000 ) >> 27;
-}
-
-
-/*******************************************************************
- * sysEUMBBARRead - Read a 32-bit EUMBBAR register
- *
- * This routine reads the content of a register in the Embedded
- * Utilities Memory Block, and swaps to big endian before returning
- * the value.
- *
- * RETURNS: The content of the specified EUMBBAR register.
- */
-
-ULONG sysEUMBBARRead
- (
- ULONG regNum
- )
- {
- ULONG temp;
-
- temp = *(ULONG *) (CONFIG_SYS_EUMB_ADDR + regNum);
- return ( LONGSWAP(temp));
- }
-
-/*******************************************************************
- * sysEUMBBARWrite - Write a 32-bit EUMBBAR register
- *
- * This routine swaps the value to little endian then writes it to
- * a register in the Embedded Utilities Memory Block address space.
- *
- * RETURNS: N/A
- */
-
-void sysEUMBBARWrite
- (
- ULONG regNum, /* EUMBBAR register address */
- ULONG regVal /* Value to be written */
- )
- {
-
- *(ULONG *) (CONFIG_SYS_EUMB_ADDR + regNum) = LONGSWAP(regVal);
- return ;
- }
-
-
-/********************************************************
- * function: epicVendorId
- *
- * description: return the EPIC Vendor Identification
- * register:
- *
- * siliccon version, device id, and vendor id
- *
- * note:
- ********************************************************/
-void epicVendorId
- (
- unsigned int *step,
- unsigned int *devId,
- unsigned int *venId
- )
- {
- ULONG val;
- val = sysEUMBBARRead( EPIC_VENDOR_ID_REG );
- *step = ( val & 0x00FF0000 ) >> 16;
- *devId = ( val & 0x0000FF00 ) >> 8;
- *venId = ( val & 0x000000FF );
- }
-
-/**************************************************
- * function: epicFeatures
- *
- * description: return the number of IRQ supported,
- * number of CPU, and the version of the
- * OpenEPIC
- *
- * note:
- *************************************************/
-void epicFeatures
- (
- unsigned int *noIRQs,
- unsigned int *noCPUs,
- unsigned int *verId
- )
- {
- ULONG val;
-
- val = sysEUMBBARRead( EPIC_FEATURES_REG );
- *noIRQs = ( val & 0x07FF0000 ) >> 16;
- *noCPUs = ( val & 0x00001F00 ) >> 8;
- *verId = ( val & 0x000000FF );
-}
-
-
-/*********************************************************
- * function: epciTmFrequncySet
- *
- * description: Set the timer frequency reporting register
- ********************************************************/
-void epicTmFrequencySet( unsigned int frq )
-{
- sysEUMBBARWrite(EPIC_TM_FREQ_REG, frq);
-}
-
-/*******************************************************
- * function: epicTmFrequncyGet
- *
- * description: Get the current value of the Timer Frequency
- * Reporting register
- *
- ******************************************************/
-unsigned int epicTmFrequencyGet(void)
-{
- return( sysEUMBBARRead(EPIC_TM_FREQ_REG)) ;
-}
-
-
-/****************************************************
- * function: epicTmBaseSet
- *
- * description: Set the #n global timer base count register
- * return 0 if no error, otherwise return 1.
- *
- * note:
- ****************************************************/
-unsigned int epicTmBaseSet
- (
- ULONG srcAddr, /* Address of the Timer Base register */
- unsigned int cnt, /* Base count */
- unsigned int inhibit /* 1 - count inhibit */
- )
-{
-
- unsigned int val = 0x80000000;
- /* First inhibit counting the timer */
- sysEUMBBARWrite(srcAddr, val) ;
-
- /* set the new value */
- val = (cnt & 0x7fffffff) | ((inhibit & 0x1) << 31);
- sysEUMBBARWrite(srcAddr, val) ;
- return 0;
-}
-
-/***********************************************************************
- * function: epicTmBaseGet
- *
- * description: Get the current value of the global timer base count register
- * return 0 if no error, otherwise return 1.
- *
- * note:
- ***********************************************************************/
-unsigned int epicTmBaseGet( ULONG srcAddr, unsigned int *val )
-{
- *val = sysEUMBBARRead( srcAddr );
- *val = *val & 0x7fffffff;
- return 0;
-}
-
-/***********************************************************
- * function: epicTmCountGet
- *
- * description: Get the value of a given global timer
- * current count register
- * return 0 if no error, otherwise return 1
- * note:
- **********************************************************/
-unsigned int epicTmCountGet( ULONG srcAddr, unsigned int *val )
-{
- *val = sysEUMBBARRead( srcAddr );
- *val = *val & 0x7fffffff;
- return 0;
-}
-
-
-/***********************************************************
- * function: epicTmInhibit
- *
- * description: Stop counting of a given global timer
- * return 0 if no error, otherwise return 1
- *
- * note:
- ***********************************************************/
-unsigned int epicTmInhibit( unsigned int srcAddr )
-{
- ULONG val;
-
- val = sysEUMBBARRead( srcAddr );
- val |= 0x80000000;
- sysEUMBBARWrite( srcAddr, val );
- return 0;
-}
-
-/******************************************************************
- * function: epicTmEnable
- *
- * description: Enable counting of a given global timer
- * return 0 if no error, otherwise return 1
- *
- * note:
- *****************************************************************/
-unsigned int epicTmEnable( ULONG srcAddr )
-{
- ULONG val;
-
- val = sysEUMBBARRead( srcAddr );
- val &= 0x7fffffff;
- sysEUMBBARWrite( srcAddr, val );
- return 0;
-}
-
-void epicSourcePrint(int Vect)
- {
- ULONG srcVal;
-
- srcVal = sysEUMBBARRead(SrcVecTable[Vect].srcAddr);
- PRINT("%s\n", SrcVecTable[Vect].srcName);
- PRINT("Address = 0x%lx\n", SrcVecTable[Vect].srcAddr);
- PRINT("Vector = %ld\n", (srcVal & 0x000000FF) );
- PRINT("Mask = %ld\n", srcVal >> 31);
- PRINT("Activitiy = %ld\n", (srcVal & 40000000) >> 30);
- PRINT("Polarity = %ld\n", (srcVal & 0x00800000) >> 23);
- PRINT("Sense = %ld\n", (srcVal & 0x00400000) >> 22);
- PRINT("Priority = %ld\n", (srcVal & 0x000F0000) >> 16);
- }
diff --git a/arch/powerpc/cpu/mpc824x/drivers/epic/epic2.S b/arch/powerpc/cpu/mpc824x/drivers/epic/epic2.S
deleted file mode 100644
index 52d19aa..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/epic/epic2.S
+++ /dev/null
@@ -1,196 +0,0 @@
-/**************************************
- *
- * copyright @ Motorola, 1999
- *
- **************************************/
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-#include <asm/processor.h>
-
-/*********************************************
- * function: CoreExtIntEnable
- *
- * description: Enable 603e core external interrupt
- *
- * note: mtmsr is context-synchronization
- **********************************************/
- .text
- .align 2
- .global CoreExtIntEnable
-CoreExtIntEnable:
- mfmsr r3
-
- ori r3,r3,0x8000 /* enable external interrupt */
- mtmsr r3
-
- bclr 20, 0
-
-/*******************************************
- * function: CoreExtIntDisable
- *
- * description: Disable 603e core external interrupt
- *
- * note:
- *******************************************/
- .text
- .align 2
- .global CoreExtIntDisable
-CoreExtIntDisable:
- mfmsr r4
-
- xor r3,r3,r3
- or r3,r3,r4
-
- andis. r4,r4,0xffff
- andi. r3,r3,0x7fff /* disable external interrupt */
-
- or r3,r3,r4
- mtmsr r3
-
- bclr 20, 0
-
-/*********************************************************
- * function: epicEOI
- *
- * description: signal the EOI and restore machine status
- * Input: r3 - value of eumbbar
- * Output: r3 - value of eumbbar
- * r4 - ISR vector value
- * note:
- ********************************************************/
- .text
- .align 2
- .global epicEOI
-epicEOI:
- lis r5,0x0006 /* Build End Of Interrupt Register offset */
- ori r5,r5,0x00b0
- xor r7,r7,r7 /* Clear r7 */
- stwbrx r7,r5,r3 /* Save r7, writing to this register will
- * intidate the end of processing the
- * highest interrupt.
- */
- sync
-
- /* ---RESTORE MACHINE STATE */
- mfmsr r13 /* Clear Recoverable Interrupt bit in MSR */
- or r7,r7,r13
-
- andis. r7,r7,0xffff
- andi. r13,r13,0x7ffd /* (and disable interrupts) */
- or r13,r13,r7
- mtmsr r13
-
- lwz r13,0x1c(r1) /* pull ctr */
- mtctr r13
-
- lwz r13,0x18(r1) /* pull xer */
- mtctr r13
-
- lwz r13,0x14(r1) /* pull lr */
- mtctr r13
-
- lwz r13,0x10(r1) /* Pull SRR1 from stack */
- mtspr SRR1,r13 /* Restore SRR1 */
-
- lwz r13,0xc(r1) /* Pull SRR0 from stack */
- mtspr SRR0,r13 /* Restore SRR0 */
-
- lwz r13,0x8(r1) /* Pull User stack pointer from stack */
- mtspr SPRG1,r13 /* Restore SPRG1 */
-
- lwz r4,0x4(r1) /* vector value */
- lwz r3,0x0(r1) /* eumbbar */
- sync
-
- addi r1,r1,0x20 /* Deallocate stack */
- mtspr SPRG0,r1 /* Save updated Supervisor stack pointer */
- mfspr r1,SPRG1 /* Restore User stack pointer */
-
- bclr 20,0
-
-/***********************************************************
- * function: exception routine called by exception vector
- * at 0x500, external interrupt
- *
- * description: Kahlua EPIC controller
- *
- * input: r3 - content of eumbbar
- * output: r3 - ISR return value
- * r4 - Interrupt vector number
- * note:
- ***********************************************************/
-
- .text
- .align 2
- .global epic_exception
-
-epic_exception:
-
- /*---SAVE MACHINE STATE TO A STACK */
- mtspr SPRG1,r1 /* Save User stack pointer to SPRG1 */
- mfspr r1,SPRG0 /* Load Supervisor stack pointer into r1 */
-
- stwu r3,-0x20(r1) /* Push the value of eumbbar onto stack */
-
- mfspr r3,SPRG1 /* Push User stack pointer onto stack */
- stw r3,0x8(r1)
- mfspr r3,SRR0 /* Push SRR0 onto stack */
- stw r1,0xc(r1)
- mfspr r3,SRR1 /* Push SRR1 onto stack */
- stw r3,0x10(r1)
- mflr r3
- stw r3,0x14(r1) /* Push LR */
- mfxer r3
- stw r3,0x18(r1) /* Push Xer */
- mfctr r3
- stw r3,0x1c(r1) /* Push CTR */
-
- mtspr SPRG0,r1 /* Save updated Supervisor stack pointer
- * value to SPRG0
- */
- mfmsr r3
- ori r3,r3,0x0002 /* Set Recoverable Interrupt bit in MSR */
- mtmsr r3
-
- /* ---READ IN THE EUMBAR REGISTER */
- lwz r6,0(r1) /* this is eumbbar */
- sync
-
- /* ---READ EPIC REGISTER: PROCESSOR INTERRUPT ACKNOWLEDGE REGISTER */
- lis r5,0x0006 /* Build Interrupt Acknowledge Register
- * offset
- */
- ori r5,r5,0x00a0
- lwbrx r7,r5,r6 /* Load interrupt vector into r7 */
- sync
-
- /* --MASK OFF ALL BITS EXCEPT THE VECTOR */
- xor r3,r3,r3
- xor r4,r4,r4
- or r3, r3, r6 /* eumbbar in r3 */
- andi. r4,r7,0x00ff /* Mask off bits, vector in r4 */
-
- stw r4,0x04(r1) /* save the vector value */
-
- lis r5,epicISR at ha
- ori r5,r5,epicISR at l
- mtlr r5
- blrl
-
- xor r30,r30,r30
- or r30,r30,r3 /* save the r3 which containts the return value from epicISR */
-
- /* ---READ IN THE EUMBAR REGISTER */
- lwz r3,0(r1)
- sync
-
- lis r5,epicEOI at ha
- ori r5,r5,epicEOI at l
- mtlr r5
- blrl
-
- xor r3,r3,r3
- or r3,r3,r30 /* restore the ISR return value */
-
- bclr 20,0
diff --git a/arch/powerpc/cpu/mpc824x/drivers/epic/epicutil.S b/arch/powerpc/cpu/mpc824x/drivers/epic/epicutil.S
deleted file mode 100644
index 4877050..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/epic/epicutil.S
+++ /dev/null
@@ -1,57 +0,0 @@
-/**************************************
- *
- * copyright @ Motorola, 1999
- *
- *
- * This file contains two commonly used
- * lower level utility routines.
- *
- * The utility routines are also in other
- * Kahlua device driver libraries. The
- * need to be linked in only once.
- **************************************/
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-/**********************************************************
- * function: load_runtime_reg
- *
- * input: r3 - value of eumbbar
- * r4 - register offset in embedded utility space
- *
- * output: r3 - register content
- **********************************************************/
- .text
- .align 2
- .global load_runtime_reg
-
-load_runtime_reg:
-
- xor r5,r5,r5
- or r5,r5,r3 /* save eumbbar */
-
- lwbrx r3,r4,r5
- sync
-
- bclr 20, 0
-
-/****************************************************************
- * function: store_runtime_reg
- *
- * input: r3 - value of eumbbar
- * r4 - register offset in embedded utility space
- * r5 - new value to be stored
- *
- ****************************************************************/
- .text
- .align 2
- .global store_runtime_reg
-store_runtime_reg:
-
- xor r0,r0,r0
-
- stwbrx r5, r4, r3
- sync
-
- bclr 20,0
diff --git a/arch/powerpc/cpu/mpc824x/drivers/errors.h b/arch/powerpc/cpu/mpc824x/drivers/errors.h
deleted file mode 100644
index 20794a2..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/errors.h
+++ /dev/null
@@ -1,212 +0,0 @@
-/* Copyright Motorola, Inc. 1993, 1994
- ALL RIGHTS RESERVED
-
- You are hereby granted a copyright license to use, modify, and
- distribute the SOFTWARE so long as this entire notice is retained
- without alteration in any modified and/or redistributed versions,
- and that such modified versions are clearly identified as such.
- No licenses are granted by implication, estoppel or otherwise under
- any patents or trademarks of Motorola, Inc.
-
- The SOFTWARE is provided on an "AS IS" basis and without warranty.
- To the maximum extent permitted by applicable law, MOTOROLA DISCLAIMS
- ALL WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING IMPLIED
- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
- PURPOSE AND ANY WARRANTY AGAINST INFRINGEMENT WITH
- REGARD TO THE SOFTWARE (INCLUDING ANY MODIFIED VERSIONS
- THEREOF) AND ANY ACCOMPANYING WRITTEN MATERIALS.
-
- To the maximum extent permitted by applicable law, IN NO EVENT SHALL
- MOTOROLA BE LIABLE FOR ANY DAMAGES WHATSOEVER
- (INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS OF
- BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
- INFORMATION, OR OTHER PECUNIARY LOSS) ARISING OF THE USE OR
- INABILITY TO USE THE SOFTWARE. Motorola assumes no responsibility
- for the maintenance and support of the SOFTWARE.
-
-*/
-
-
-#include "config.h"
-
-/*
- 1 2 3 4 5 6 7 8
-01234567890123456789012345678901234567890123456789012345678901234567890123456789
-*/
-/* List define statements here */
-
-/* These are for all the toolboxes and functions to use. These will help
-to standardize the error handling in the current project */
-
- /* this is the "data type" for the error
- messages in the system */
-#define STATUS unsigned int
-
- /* this is a success status code */
-#define SUCCESS 1
-
- /* likewise this is failure */
-#define FAILURE 0
-
-#define NUM_ERRORS 47
-
-/* This first section of "defines" are for error codes ONLY. The called
- routine will return one of these error codes to the caller. If the final
- returned code is "VALID", then everything is a-okay. However, if one
- of the functions returns a non-valid status, that error code should be
- propogated back to all the callers. At the end, the last caller will
- call an error_processing function, and send in the status which was
- returned. It's up to the error_processing function to determine which
- error occured (as indicated by the status), and print an appropriate
- message back to the user.
-*/
-/*----------------------------------------------------------------------*/
-/* these are specifically for the parser routines */
-
-#define UNKNOWN_COMMAND 0xfb00 /* "unrecognized command " */
-#define UNKNOWN_REGISTER 0xfb01 /* "unknown register "*/
-#define ILLEGAL_RD_STAGE 0xfb02 /* cannot specify reg. family in range*/
-#define ILLEGAL_REG_FAMILY 0xfb03 /* "cannot specify a range of special
- or miscellaneous registers"*/
-#define RANGE_CROSS_FAMILY 0xfb04 /* "cannot specify a range across
- register families" */
-#define UNIMPLEMENTED_STAGE 0xfb05 /* invalid rd or rmm parameter format */
-#define REG_NOT_WRITEABLE 0xfb06 /* "unknown operator in arguements"*/
-#define INVALID_FILENAME 0xfb07 /* "invalid download filename" */
-#define INVALID_BAUD_RATE 0xfb08 /* invalid baud rate from sb command */
-#define UNSUPPORTED_REGISTER 0xfb09 /* Special register is not supported */
-#define FOR_BOARD_ONLY 0xfb0a /* "Not available for Unix." */
-
-
-/*----------------------------------------------------------------------*/
-/* these are for the error checking toolbox */
-
-#define INVALID 0xfd00 /* NOT valid */
-#define VALID 0xfd01 /* valid */
-
- /* This error is found in the fcn:
- is_right_size_input() to indicate
- that the input was not 8 characters
- long. */
-#define INVALID_SIZE 0xfd02
-
- /* This error is found in the fcn:
- is_valid_address_range() to indicate
- that the address given falls outside
- of valid memory defined by MEM_START
- to MEM_END.
- */
-#define OUT_OF_BOUNDS_ADDRESS 0xfd03
-
- /* This error is found in the fcn:
- is_valid_hex_input() to indicate that
- one of more of the characters entered
- are not valid hex characters. Valid
- hex characters are 0-9, A-F, a-f.
- */
-#define INVALID_HEX_INPUT 0xfd04
-
- /* This error is found in the fcn:
- is_valid_register_number() to indicate
- that a given register does not exist.
- */
-#define REG_NOT_READABLE 0xfd05
-
- /* This error is found in the fcn:
- is_word_aligned_address() to indicate
- that the given address is not word-
- aligned. A word-aligned address ends
- in 0x0,0x4,0x8,0xc.
- */
-#define NOT_WORD_ALIGNED 0xfd07
-
- /* This error is found in the fcn:
- is_valid_address_range() to indicate
- that the starting address is greater
- than the ending address.
- */
-#define REVERSED_ADDRESS 0xfd08
-
- /* this error tells us that the address
- specified as the destination is within
- the source addresses */
-#define RANGE_OVERLAP 0xfd09
-
-
-#define ERROR 0xfd0a /* An error occured */
-#define INVALID_PARAM 0xfd0b /* "invalid input parameter " */
-
-
-#define INVALID_FLAG 0xfd0c /* invalid flag */
-
-/*----------------------------------------------------------------------*/
-/* these are for the getarg toolbox */
-
-#define INVALID_NUMBER_ARGS 0xFE00 /* invalid number of commd arguements */
-#define UNKNOWN_PARAMETER 0xFE01 /* "unknown type of parameter "*/
-
-
-/*----------------------------------------------------------------------*/
-/* these are for the tokenizer toolbox */
-
-#define ILLEGAL_CHARACTER 0xFF00 /* unrecognized char. in input stream*/
-#define TTL_NOT_SORTED 0xFF01 /* token translation list not sorted */
-#define TTL_NOT_DEFINED 0xFF02 /* token translation list not assigned*/
-#define INVALID_STRING 0xFF03 /* unable to extract string from input */
-#define BUFFER_EMPTY 0xFF04 /* "input buffer is empty" */
-#define INVALID_MODE 0xFF05 /* input buf is in an unrecognized mode*/
-#define TOK_INTERNAL_ERROR 0xFF06 /* "internal tokenizer error" */
-#define TOO_MANY_IBS 0xFF07 /* "too many open input buffers" */
-#define NO_OPEN_IBS 0xFF08 /* "no open input buffers" */
-
-
-/* these are for the read from screen toolbox */
-
-#define RESERVED_WORD 0xFC00 /* used a reserved word as an arguement*/
-
-
-/* these are for the breakpoint routines */
-
-#define FULL_BPDS 0xFA00 /* breakpoint data structure is full */
-
-
-/* THESE are for the downloader */
-
-#define NOT_IN_S_RECORD_FORMAT 0xf900 /* "not in S-Record Format" */
-#define UNREC_RECORD_TYPE 0xf901 /* "unrecognized record type" */
-#define CONVERSION_ERROR 0xf902 /* "ascii to int conversion error" */
-#define INVALID_MEMORY 0xf903 /* "bad s-record memory address " */
-
-
-/* these are for the compression and decompression stuff */
-
-#define COMP_UNK_CHARACTER 0xf800 /* "unknown compressed character " */
-
-#define COMP_UNKNOWN_STATE 0xf801 /* "unknown binary state" */
-
-#define NOT_IN_COMPRESSED_FORMAT 0xf802 /* not in compressed S-Record format */
-
-
-/* these are for the DUART handling things */
-
- /* "unrecognized serial port configuration" */
-#define UNKNOWN_PORT_STATE 0xf700
-
-
-/* these are for the register toolbox */
-
- /* "cannot find register in special
- purpose register file " */
-#define SPR_NOT_FOUND 0xf600
-
-
-/* these are for the duart specific stuff */
-
- /* "transparent mode needs access to
- two serial ports" */
-#define TM_NEEDS_BOTH_PORTS 0xf500
-
-
-/*----------------------------------------------------------------------*/
-/* these are specifically for the flash routines */
-#define FLASH_ERROR 0xf100 /* general flash error */
diff --git a/arch/powerpc/cpu/mpc824x/drivers/i2c/i2c.c b/arch/powerpc/cpu/mpc824x/drivers/i2c/i2c.c
deleted file mode 100644
index 3638ab0..0000000
--- a/arch/powerpc/cpu/mpc824x/drivers/i2c/i2c.c
+++ /dev/null
@@ -1,254 +0,0 @@
-/*
- * (C) Copyright 2003
- * Gleb Natapov <gnatapov@mrv.com>
- * Some bits are taken from linux driver writen by adrian at humboldt.co.uk
- *
- * Hardware I2C driver for MPC107 PCI bridge.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-#undef I2CDBG
-
-#ifdef CONFIG_HARD_I2C
-#include <i2c.h>
-
-#define TIMEOUT (CONFIG_SYS_HZ/4)
-
-#define I2C_Addr ((unsigned *)(CONFIG_SYS_EUMB_ADDR + 0x3000))
-
-#define I2CADR &I2C_Addr[0]
-#define I2CFDR &I2C_Addr[1]
-#define I2CCCR &I2C_Addr[2]
-#define I2CCSR &I2C_Addr[3]
-#define I2CCDR &I2C_Addr[4]
-
-#define MPC107_CCR_MEN 0x80
-#define MPC107_CCR_MIEN 0x40
-#define MPC107_CCR_MSTA 0x20
-#define MPC107_CCR_MTX 0x10
-#define MPC107_CCR_TXAK 0x08
-#define MPC107_CCR_RSTA 0x04
-
-#define MPC107_CSR_MCF 0x80
-#define MPC107_CSR_MAAS 0x40
-#define MPC107_CSR_MBB 0x20
-#define MPC107_CSR_MAL 0x10
-#define MPC107_CSR_SRW 0x04
-#define MPC107_CSR_MIF 0x02
-#define MPC107_CSR_RXAK 0x01
-
-#define I2C_READ 1
-#define I2C_WRITE 0
-
-/* taken from linux include/asm-ppc/io.h */
-inline unsigned in_le32 (volatile unsigned *addr)
-{
- unsigned ret;
-
- __asm__ __volatile__ ("lwbrx %0,0,%1;\n"
- "twi 0,%0,0;\n"
- "isync":"=r" (ret): "r" (addr), "m" (*addr));
- return ret;
-}
-
-inline void out_le32 (volatile unsigned *addr, int val)
-{
- __asm__ __volatile__ ("stwbrx %1,0,%2; eieio":"=m" (*addr):"r" (val),
- "r" (addr));
-}
-
-#define writel(val, addr) out_le32(addr, val)
-#define readl(addr) in_le32(addr)
-
-void i2c_init (int speed, int slaveadd)
-{
- /* stop I2C controller */
- writel (0x0, I2CCCR);
- /* set clock */
- writel (0x1020, I2CFDR);
- /* write slave address */
- writel (slaveadd, I2CADR);
- /* clear status register */
- writel (0x0, I2CCSR);
- /* start I2C controller */
- writel (MPC107_CCR_MEN, I2CCCR);
-
- return;
-}
-
-static __inline__ int i2c_wait4bus (void)
-{
- ulong timeval = get_timer (0);
-
- while (readl (I2CCSR) & MPC107_CSR_MBB)
- if (get_timer (timeval) > TIMEOUT)
- return -1;
-
- return 0;
-}
-
-static __inline__ int i2c_wait (int write)
-{
- u32 csr;
- ulong timeval = get_timer (0);
-
- do {
- csr = readl (I2CCSR);
-
- if (!(csr & MPC107_CSR_MIF))
- continue;
-
- writel (0x0, I2CCSR);
-
- if (csr & MPC107_CSR_MAL) {
-#ifdef I2CDBG
- printf ("i2c_wait: MAL\n");
-#endif
- return -1;
- }
-
- if (!(csr & MPC107_CSR_MCF)) {
-#ifdef I2CDBG
- printf ("i2c_wait: unfinished\n");
-#endif
- return -1;
- }
-
- if (write == I2C_WRITE && (csr & MPC107_CSR_RXAK)) {
-#ifdef I2CDBG
- printf ("i2c_wait: No RXACK\n");
-#endif
- return -1;
- }
-
- return 0;
- } while (get_timer (timeval) < TIMEOUT);
-
-#ifdef I2CDBG
- printf ("i2c_wait: timed out\n");
-#endif
- return -1;
-}
-
-static __inline__ int i2c_write_addr (u8 dev, u8 dir, int rsta)
-{
- writel (MPC107_CCR_MEN | MPC107_CCR_MSTA | MPC107_CCR_MTX |
- (rsta ? MPC107_CCR_RSTA : 0), I2CCCR);
-
- writel ((dev << 1) | dir, I2CCDR);
-
- if (i2c_wait (I2C_WRITE) < 0)
- return 0;
-
- return 1;
-}
-
-static __inline__ int __i2c_write (u8 * data, int length)
-{
- int i;
-
- writel (MPC107_CCR_MEN | MPC107_CCR_MSTA | MPC107_CCR_MTX, I2CCCR);
-
- for (i = 0; i < length; i++) {
- writel (data[i], I2CCDR);
-
- if (i2c_wait (I2C_WRITE) < 0)
- break;
- }
-
- return i;
-}
-
-static __inline__ int __i2c_read (u8 * data, int length)
-{
- int i;
-
- writel (MPC107_CCR_MEN | MPC107_CCR_MSTA |
- ((length == 1) ? MPC107_CCR_TXAK : 0), I2CCCR);
-
- /* dummy read */
- readl (I2CCDR);
-
- for (i = 0; i < length; i++) {
- if (i2c_wait (I2C_READ) < 0)
- break;
-
- /* Generate ack on last next to last byte */
- if (i == length - 2)
- writel (MPC107_CCR_MEN | MPC107_CCR_MSTA |
- MPC107_CCR_TXAK, I2CCCR);
-
- /* Generate stop on last byte */
- if (i == length - 1)
- writel (MPC107_CCR_MEN | MPC107_CCR_TXAK, I2CCCR);
-
- data[i] = readl (I2CCDR);
- }
-
- return i;
-}
-
-int i2c_read (u8 dev, uint addr, int alen, u8 * data, int length)
-{
- int i = 0;
- u8 *a = (u8 *) & addr;
-
- if (i2c_wait4bus () < 0)
- goto exit;
-
- if (i2c_write_addr (dev, I2C_WRITE, 0) == 0)
- goto exit;
-
- if (__i2c_write (&a[4 - alen], alen) != alen)
- goto exit;
-
- if (i2c_write_addr (dev, I2C_READ, 1) == 0)
- goto exit;
-
- i = __i2c_read (data, length);
-
-exit:
- writel (MPC107_CCR_MEN, I2CCCR);
-
- return !(i == length);
-}
-
-int i2c_write (u8 dev, uint addr, int alen, u8 * data, int length)
-{
- int i = 0;
- u8 *a = (u8 *) & addr;
-
- if (i2c_wait4bus () < 0)
- goto exit;
-
- if (i2c_write_addr (dev, I2C_WRITE, 0) == 0)
- goto exit;
-
- if (__i2c_write (&a[4 - alen], alen) != alen)
- goto exit;
-
- i = __i2c_write (data, length);
-
-exit:
- writel (MPC107_CCR_MEN, I2CCCR);
-
- return !(i == length);
-}
-
-int i2c_probe (uchar chip)
-{
- int tmp;
-
- /*
- * Try to read the first location of the chip. The underlying
- * driver doesn't appear to support sending just the chip address
- * and looking for an <ACK> back.
- */
- udelay (10000);
- return i2c_read (chip, 0, 1, (uchar *) &tmp, 1);
-}
-
-#endif /* CONFIG_HARD_I2C */
diff --git a/arch/powerpc/cpu/mpc824x/interrupts.c b/arch/powerpc/cpu/mpc824x/interrupts.c
deleted file mode 100644
index fad103f..0000000
--- a/arch/powerpc/cpu/mpc824x/interrupts.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * (C) Copyright 2000-2002
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/pci_io.h>
-#include <commproc.h>
-#include "drivers/epic.h"
-
-int interrupt_init_cpu (unsigned *decrementer_count)
-{
- *decrementer_count = (get_bus_freq (0) / 4) / CONFIG_SYS_HZ;
-
- /*
- * It's all broken at the moment and I currently don't need
- * interrupts. If you want to fix it, have a look at the epic
- * drivers in dink32 v12. They do everthing and Motorola said
- * I could use the dink source in this project as long as
- * copyright notices remain intact.
- */
-
- epicInit (EPIC_DIRECT_IRQ, 0);
- /* EPIC won't generate INT unless Current Task Pri < 15 */
- epicCurTaskPrioSet(0);
-
- return (0);
-}
-
-/****************************************************************************/
-
-/*
- * Handle external interrupts
- */
-void external_interrupt (struct pt_regs *regs)
-{
- register unsigned long temp;
-
- pci_readl (CONFIG_SYS_EUMB_ADDR + EPIC_PROC_INT_ACK_REG, temp);
- sync (); /* i'm not convinced this is needed, but dink source has it */
- temp &= 0xff; /*get vector */
-
- /*TODO: handle them -... */
- epicEOI ();
-}
-
-/****************************************************************************/
-
-/*
- * blank int handlers.
- */
-
-void
-irq_install_handler (int vec, interrupt_handler_t * handler, void *arg)
-{
-}
-
-void irq_free_handler (int vec)
-{
-
-}
-
-/*TODO: some handlers for winbond and 87308 interrupts
- and what about generic pci inteerupts?
- vga?
- */
-
-void timer_interrupt_cpu (struct pt_regs *regs)
-{
- /* nothing to do here */
- return;
-}
diff --git a/arch/powerpc/cpu/mpc824x/pci.c b/arch/powerpc/cpu/mpc824x/pci.c
deleted file mode 100644
index 1257b08..0000000
--- a/arch/powerpc/cpu/mpc824x/pci.c
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * arch/powerpc/kernel/mpc10x_common.c
- *
- * Common routines for the Motorola SPS MPC106, MPC107 and MPC8240 Host bridge,
- * Mem ctlr, EPIC, etc.
- *
- * Author: Mark A. Greer
- * mgreer@mvista.com
- *
- * Copyright 2001 MontaVista Software Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-#ifdef CONFIG_PCI
-
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <pci.h>
-#include <mpc824x.h>
-
-void pci_mpc824x_init (struct pci_controller *hose)
-{
- hose->first_busno = 0;
- hose->last_busno = 0xff;
-
- /* System memory space */
- pci_set_region(hose->regions + 0,
- CHRP_PCI_MEMORY_BUS,
- CHRP_PCI_MEMORY_PHYS,
- CHRP_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
-
- /* PCI memory space */
- pci_set_region(hose->regions + 1,
- CHRP_PCI_MEM_BUS,
- CHRP_PCI_MEM_PHYS,
- CHRP_PCI_MEM_SIZE,
- PCI_REGION_MEM);
-
- /* ISA/PCI memory space */
- pci_set_region(hose->regions + 2,
- CHRP_ISA_MEM_BUS,
- CHRP_ISA_MEM_PHYS,
- CHRP_ISA_MEM_SIZE,
- PCI_REGION_MEM);
-
- /* PCI I/O space */
- pci_set_region(hose->regions + 3,
- CHRP_PCI_IO_BUS,
- CHRP_PCI_IO_PHYS,
- CHRP_PCI_IO_SIZE,
- PCI_REGION_IO);
-
- /* ISA/PCI I/O space */
- pci_set_region(hose->regions + 4,
- CHRP_ISA_IO_BUS,
- CHRP_ISA_IO_PHYS,
- CHRP_ISA_IO_SIZE,
- PCI_REGION_IO);
-
- hose->region_count = 5;
-
- pci_setup_indirect(hose,
- CHRP_REG_ADDR,
- CHRP_REG_DATA);
-
- pci_register_hose(hose);
-
- hose->last_busno = pci_hose_scan(hose);
-}
-
-#endif
diff --git a/arch/powerpc/cpu/mpc824x/speed.c b/arch/powerpc/cpu/mpc824x/speed.c
deleted file mode 100644
index e6064a1..0000000
--- a/arch/powerpc/cpu/mpc824x/speed.c
+++ /dev/null
@@ -1,102 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * Gregory E. Allen, gallen at arlut.utexas.edu
- * Applied Research Laboratories, The University of Texas at Austin
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-/* NOTE: This describes the proper use of this file.
- *
- * CONFIG_SYS_CLK_FREQ should be defined as the input frequency on
- * PCI_SYNC_IN .
- *
- * CONFIG_PLL_PCI_TO_MEM_MULTIPLIER is only required on MPC8240
- * boards. It should be defined as the PCI to Memory Multiplier as
- * documented in the MPC8240 Hardware Specs.
- *
- * Other mpc824x boards don't need CONFIG_PLL_PCI_TO_MEM_MULTIPLIER
- * because they can determine it from the PCR.
- *
- * Gary Milliorn <gary.milliorn@motorola.com> (who should know since
- * he designed the Sandpoint) told us that the PCR is not in all revs
- * of the MPC8240 CPU, so it's not guaranteeable and we cannot do
- * away with CONFIG_PLL_PCI_TO_MEM_MULTIPLIER altogether.
- */
-/* ------------------------------------------------------------------------- */
-
-/* This gives the PCI to Memory multiplier times 10 */
-/* The index is the value of PLL_CFG[0:4] */
-/* This is documented in the MPC8240/5 Hardware Specs */
-
-short pll_pci_to_mem_multiplier[] = {
-#if defined(CONFIG_MPC8240)
- 30, 30, 10, 10, 20, 10, 0, 10,
- 10, 0, 20, 0, 20, 0, 20, 0,
- 30, 0, 15, 0, 20, 0, 20, 0,
- 25, 0, 10, 0, 15, 15, 0, 0,
-#elif defined(CONFIG_MPC8245)
- 30, 30, 10, 10, 20, 10, 10, 10,
- 10, 20, 20, 15, 20, 15, 20, 30,
- 30, 40, 15, 40, 20, 25, 20, 40,
- 25, 20, 10, 20, 15, 15, 15, 0,
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-};
-
-#define CU824_PLL_STATE_REG 0xFE80002F
-#define PCR 0x800000E2
-
-/* ------------------------------------------------------------------------- */
-
-/* compute the memory bus clock frequency */
-ulong get_bus_freq (ulong dummy)
-{
- unsigned char pll_cfg;
-#if defined(CONFIG_MPC8240) && !defined(CONFIG_CU824)
- return (CONFIG_SYS_CLK_FREQ) * (CONFIG_PLL_PCI_TO_MEM_MULTIPLIER);
-#elif defined(CONFIG_CU824)
- pll_cfg = *(volatile unsigned char *) (CU824_PLL_STATE_REG);
- pll_cfg &= 0x1f;
-#else
- CONFIG_READ_BYTE(PCR, pll_cfg);
- pll_cfg = (pll_cfg >> 3) & 0x1f;
-#endif
- return ((CONFIG_SYS_CLK_FREQ) * pll_pci_to_mem_multiplier[pll_cfg] + 5) / 10;
-}
-
-
-/* ------------------------------------------------------------------------- */
-
-/* This gives the Memory to CPU Core multiplier times 10 */
-/* The index is the value of PLLRATIO in HID1 */
-/* This is documented in the MPC8240 Hardware Specs */
-/* This is not documented for MPC8245 ? FIXME */
-short pllratio_to_factor[] = {
- 0, 0, 0, 10, 20, 20, 25, 45,
- 30, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 10, 0, 0, 0, 45,
- 30, 0, 40, 0, 0, 0, 35, 0,
-};
-
-/* compute the CPU and memory bus clock frequencies */
-int get_clocks (void)
-{
- uint hid1 = mfspr(HID1);
- hid1 = (hid1 >> (32-5)) & 0x1f;
- gd->cpu_clk = (pllratio_to_factor[hid1] * get_bus_freq(0) + 5)
- / 10;
- gd->bus_clk = get_bus_freq(0);
- return (0);
-}
diff --git a/arch/powerpc/cpu/mpc824x/start.S b/arch/powerpc/cpu/mpc824x/start.S
deleted file mode 100644
index 55238df..0000000
--- a/arch/powerpc/cpu/mpc824x/start.S
+++ /dev/null
@@ -1,724 +0,0 @@
-/*
- * Copyright (C) 1998 Dan Malek <dmalek@jlc.net>
- * Copyright (C) 1999 Magnus Damm <kieraypc01.p.y.kie.era.ericsson.se>
- * Copyright (C) 2000,2001,2002 Wolfgang Denk <wd@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* U-Boot - Startup Code for PowerPC based Embedded Boards
- *
- *
- * The processor starts at 0x00000100 and the code is executed
- * from flash. The code is organized to be at an other address
- * in memory, but as long we don't jump around before relocating.
- * board_init lies at a quite high address and when the cpu has
- * jumped there, everything is ok.
- * This works because the cpu gives the FLASH (CS0) the whole
- * address space at startup, and board_init lies as a echo of
- * the flash somewhere up there in the memorymap.
- *
- * board_init will change CS0 to be positioned at the correct
- * address and (s)dram will be positioned at address 0
- */
-#include <asm-offsets.h>
-#include <config.h>
-#include <mpc824x.h>
-#include <version.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-#include <asm/u-boot.h>
-
-/* We don't want the MMU yet.
-*/
-#undef MSR_KERNEL
-/* FP, Machine Check and Recoverable Interr. */
-#define MSR_KERNEL ( MSR_FP | MSR_ME | MSR_RI )
-
-/*
- * Set up GOT: Global Offset Table
- *
- * Use r12 to access the GOT
- */
- START_GOT
- GOT_ENTRY(_GOT2_TABLE_)
- GOT_ENTRY(_FIXUP_TABLE_)
-
- GOT_ENTRY(_start)
- GOT_ENTRY(_start_of_vectors)
- GOT_ENTRY(_end_of_vectors)
- GOT_ENTRY(transfer_to_handler)
-
- GOT_ENTRY(__init_end)
- GOT_ENTRY(__bss_end)
- GOT_ENTRY(__bss_start)
- END_GOT
-
-/*
- * r3 - 1st arg to board_init(): IMMP pointer
- * r4 - 2nd arg to board_init(): boot flag
- */
- .text
- .long 0x27051956 /* U-Boot Magic Number */
- .globl version_string
-version_string:
- .ascii U_BOOT_VERSION_STRING, "\0"
-
- . = EXC_OFF_SYS_RESET
- .globl _start
-_start:
- /* Initialize machine status; enable machine check interrupt */
- /*----------------------------------------------------------------------*/
- li r3, MSR_KERNEL /* Set FP, ME, RI flags */
- mtmsr r3
- mtspr SRR1, r3 /* Make SRR1 match MSR */
-
- addis r0,0,0x0000 /* lets make sure that r0 is really 0 */
- mtspr HID0, r0 /* disable I and D caches */
-
- mfspr r3, ICR /* clear Interrupt Cause Register */
-
- mfmsr r3 /* turn off address translation */
- addis r4,0,0xffff
- ori r4,r4,0xffcf
- and r3,r3,r4
- mtmsr r3
- isync
- sync /* the MMU should be off... */
-
-
-in_flash:
- /*
- * Setup BATs - cannot be done in C since we don't have a stack yet
- */
- bl setup_bats
-
- /* Enable MMU.
- */
- mfmsr r3
- ori r3, r3, (MSR_IR | MSR_DR)
- mtmsr r3
-
- /* Enable and invalidate data cache.
- */
- mfspr r3, HID0
- mr r2, r3
- ori r3, r3, HID0_DCE | HID0_DCI
- ori r2, r2, HID0_DCE
- sync
- mtspr HID0, r3
- mtspr HID0, r2
- sync
-
- /* Allocate Initial RAM in data cache.
- */
- lis r3, CONFIG_SYS_INIT_RAM_ADDR at h
- ori r3, r3, CONFIG_SYS_INIT_RAM_ADDR at l
- li r2, 128
- mtctr r2
-1:
- dcbz r0, r3
- addi r3, r3, 32
- bdnz 1b
-
- /* Lock way0 in data cache.
- */
- mfspr r3, 1011
- lis r2, 0xffff
- ori r2, r2, 0xff1f
- and r3, r3, r2
- ori r3, r3, 0x0080
- sync
- mtspr 1011, r3
-
- /*
- * Thisk the stack pointer *somewhere* sensible. Doesnt
- * matter much where as we'll move it when we relocate
- */
- lis r1, (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@h
- ori r1, r1, (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@l
-
- li r0, 0 /* Make room for stack frame header and */
- stwu r0, -4(r1) /* clear final stack frame so that */
- stwu r0, -4(r1) /* stack backtraces terminate cleanly */
-
- /* let the C-code set up the rest */
- /* */
- /* Be careful to keep code relocatable ! */
- /*----------------------------------------------------------------------*/
-
- GET_GOT /* initialize GOT access */
-
- /* r3: IMMR */
- bl cpu_init_f /* run low-level CPU init code (from Flash) */
-
- bl board_init_f /* run 1st part of board init code (from Flash) */
-
- /* NOTREACHED - board_init_f() does not return */
-
-
- .globl _start_of_vectors
-_start_of_vectors:
-
-/* Machine check */
- STD_EXCEPTION(EXC_OFF_MACH_CHCK, MachineCheck, MachineCheckException)
-
-/* Data Storage exception. "Never" generated on the 860. */
- STD_EXCEPTION(EXC_OFF_DATA_STOR, DataStorage, UnknownException)
-
-/* Instruction Storage exception. "Never" generated on the 860. */
- STD_EXCEPTION(EXC_OFF_INS_STOR, InstStorage, UnknownException)
-
-/* External Interrupt exception. */
- STD_EXCEPTION(EXC_OFF_EXTERNAL, ExtInterrupt, external_interrupt)
-
-/* Alignment exception. */
- . = EXC_OFF_ALIGN
-Alignment:
- EXCEPTION_PROLOG(SRR0, SRR1)
- mfspr r4,DAR
- stw r4,_DAR(r21)
- mfspr r5,DSISR
- stw r5,_DSISR(r21)
- addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_TEMPLATE(Alignment, AlignmentException, MSR_KERNEL, COPY_EE)
-
-/* Program check exception */
- . = EXC_OFF_PROGRAM
-ProgramCheck:
- EXCEPTION_PROLOG(SRR0, SRR1)
- addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_TEMPLATE(ProgramCheck, ProgramCheckException,
- MSR_KERNEL, COPY_EE)
-
- /* No FPU on MPC8xx. This exception is not supposed to happen.
- */
- STD_EXCEPTION(EXC_OFF_FPUNAVAIL, FPUnavailable, UnknownException)
-
- /* I guess we could implement decrementer, and may have
- * to someday for timekeeping.
- */
- STD_EXCEPTION(EXC_OFF_DECR, Decrementer, timer_interrupt)
- STD_EXCEPTION(0xa00, Trap_0a, UnknownException)
- STD_EXCEPTION(0xb00, Trap_0b, UnknownException)
- STD_EXCEPTION(0xc00, SystemCall, UnknownException)
-
- STD_EXCEPTION(EXC_OFF_TRACE, SingleStep, UnknownException)
-
- STD_EXCEPTION(EXC_OFF_FPUNASSIST, Trap_0e, UnknownException)
- STD_EXCEPTION(EXC_OFF_PMI, Trap_0f, UnknownException)
-
- STD_EXCEPTION(EXC_OFF_ITME, InstructionTransMiss, UnknownException)
- STD_EXCEPTION(EXC_OFF_DLTME, DataLoadTransMiss, UnknownException)
- STD_EXCEPTION(EXC_OFF_DSTME, DataStoreTransMiss, UnknownException)
- STD_EXCEPTION(EXC_OFF_IABE, InstructionBreakpoint, DebugException)
- STD_EXCEPTION(EXC_OFF_SMIE, SysManageInt, UnknownException)
- STD_EXCEPTION(0x1500, Reserved5, UnknownException)
- STD_EXCEPTION(0x1600, Reserved6, UnknownException)
- STD_EXCEPTION(0x1700, Reserved7, UnknownException)
- STD_EXCEPTION(0x1800, Reserved8, UnknownException)
- STD_EXCEPTION(0x1900, Reserved9, UnknownException)
- STD_EXCEPTION(0x1a00, ReservedA, UnknownException)
- STD_EXCEPTION(0x1b00, ReservedB, UnknownException)
- STD_EXCEPTION(0x1c00, ReservedC, UnknownException)
- STD_EXCEPTION(0x1d00, ReservedD, UnknownException)
- STD_EXCEPTION(0x1e00, ReservedE, UnknownException)
- STD_EXCEPTION(0x1f00, ReservedF, UnknownException)
-
- STD_EXCEPTION(EXC_OFF_RMTE, RunModeTrace, UnknownException)
-
- .globl _end_of_vectors
-_end_of_vectors:
-
-
- . = 0x3000
-
-/*
- * This code finishes saving the registers to the exception frame
- * and jumps to the appropriate handler for the exception.
- * Register r21 is pointer into trap frame, r1 has new stack pointer.
- */
- .globl transfer_to_handler
-transfer_to_handler:
- stw r22,_NIP(r21)
- lis r22,MSR_POW at h
- andc r23,r23,r22
- stw r23,_MSR(r21)
- SAVE_GPR(7, r21)
- SAVE_4GPRS(8, r21)
- SAVE_8GPRS(12, r21)
- SAVE_8GPRS(24, r21)
-#if 0
- andi. r23,r23,MSR_PR
- mfspr r23,SPRG3 /* if from user, fix up tss.regs */
- beq 2f
- addi r24,r1,STACK_FRAME_OVERHEAD
- stw r24,PT_REGS(r23)
-2: addi r2,r23,-TSS /* set r2 to current */
- tovirt(r2,r2,r23)
-#endif
- mflr r23
- andi. r24,r23,0x3f00 /* get vector offset */
- stw r24,TRAP(r21)
- li r22,0
- stw r22,RESULT(r21)
- mtspr SPRG2,r22 /* r1 is now kernel sp */
-#if 0
- addi r24,r2,TASK_STRUCT_SIZE /* check for kernel stack overflow */
- cmplw 0,r1,r2
- cmplw 1,r1,r24
- crand 1,1,4
- bgt stack_ovf /* if r2 < r1 < r2+TASK_STRUCT_SIZE */
-#endif
- lwz r24,0(r23) /* virtual address of handler */
- lwz r23,4(r23) /* where to go when done */
- mtspr SRR0,r24
- ori r20,r20,0x30 /* enable IR, DR */
- mtspr SRR1,r20
- mtlr r23
- SYNC
- rfi /* jump to handler, enable MMU */
-
-int_return:
- mfmsr r28 /* Disable interrupts */
- li r4,0
- ori r4,r4,MSR_EE
- andc r28,r28,r4
- SYNC /* Some chip revs need this... */
- mtmsr r28
- SYNC
- lwz r2,_CTR(r1)
- lwz r0,_LINK(r1)
- mtctr r2
- mtlr r0
- lwz r2,_XER(r1)
- lwz r0,_CCR(r1)
- mtspr XER,r2
- mtcrf 0xFF,r0
- REST_10GPRS(3, r1)
- REST_10GPRS(13, r1)
- REST_8GPRS(23, r1)
- REST_GPR(31, r1)
- lwz r2,_NIP(r1) /* Restore environment */
- lwz r0,_MSR(r1)
- mtspr SRR0,r2
- mtspr SRR1,r0
- lwz r0,GPR0(r1)
- lwz r2,GPR2(r1)
- lwz r1,GPR1(r1)
- SYNC
- rfi
-
-/* Cache functions.
-*/
- .globl icache_enable
-icache_enable:
- mfspr r5,HID0 /* turn on the I cache. */
- ori r5,r5,0x8800 /* Instruction cache only! */
- addis r6,0,0xFFFF
- ori r6,r6,0xF7FF
- and r6,r5,r6 /* clear the invalidate bit */
- sync
- mtspr HID0,r5
- mtspr HID0,r6
- isync
- sync
- blr
-
- .globl icache_disable
-icache_disable:
- mfspr r5,HID0
- addis r6,0,0xFFFF
- ori r6,r6,0x7FFF
- and r5,r5,r6
- sync
- mtspr HID0,r5
- isync
- sync
- blr
-
- .globl icache_status
-icache_status:
- mfspr r3, HID0
- srwi r3, r3, 15 /* >>15 & 1=> select bit 16 */
- andi. r3, r3, 1
- blr
-
- .globl dcache_enable
-dcache_enable:
- mfspr r5,HID0 /* turn on the D cache. */
- ori r5,r5,0x4400 /* Data cache only! */
- mfspr r4, PVR /* read PVR */
- srawi r3, r4, 16 /* shift off the least 16 bits */
- cmpi 0, 0, r3, 0xC /* Check for Max pvr */
- bne NotMax
- ori r5,r5,0x0040 /* setting the DCFA bit, for Max rev 1 errata */
-NotMax:
- addis r6,0,0xFFFF
- ori r6,r6,0xFBFF
- and r6,r5,r6 /* clear the invalidate bit */
- sync
- mtspr HID0,r5
- mtspr HID0,r6
- isync
- sync
- blr
-
- .globl dcache_disable
-dcache_disable:
- mfspr r5,HID0
- addis r6,0,0xFFFF
- ori r6,r6,0xBFFF
- and r5,r5,r6
- sync
- mtspr HID0,r5
- isync
- sync
- blr
-
- .globl dcache_status
-dcache_status:
- mfspr r3, HID0
- srwi r3, r3, 14 /* >>14 & 1=> select bit 17 */
- andi. r3, r3, 1
- blr
-
- .globl dc_read
-dc_read:
-/*TODO : who uses this, what should it do?
-*/
- blr
-
-
- .globl get_pvr
-get_pvr:
- mfspr r3, PVR
- blr
-
-
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- * r3 = dest
- * r4 = src
- * r5 = length in bytes
- * r6 = cachelinesize
- */
- .globl relocate_code
-relocate_code:
-
- mr r1, r3 /* Set new stack pointer */
- mr r9, r4 /* Save copy of Global Data pointer */
- mr r10, r5 /* Save copy of Destination Address */
-
- GET_GOT
- mr r3, r5 /* Destination Address */
-#ifdef CONFIG_SYS_RAMBOOT
- lis r4, CONFIG_SYS_SDRAM_BASE at h /* Source Address */
- ori r4, r4, CONFIG_SYS_SDRAM_BASE at l
-#else
- lis r4, CONFIG_SYS_MONITOR_BASE at h /* Source Address */
- ori r4, r4, CONFIG_SYS_MONITOR_BASE at l
-#endif
- lwz r5, GOT(__init_end)
- sub r5, r5, r4
- li r6, CONFIG_SYS_CACHELINE_SIZE /* Cache Line Size */
-
- /*
- * Fix GOT pointer:
- *
- * New GOT-PTR = (old GOT-PTR - CONFIG_SYS_MONITOR_BASE) + Destination Address
- *
- * Offset:
- */
- sub r15, r10, r4
-
- /* First our own GOT */
- add r12, r12, r15
- /* the the one used by the C code */
- add r30, r30, r15
-
- /*
- * Now relocate code
- */
-
- cmplw cr1,r3,r4
- addi r0,r5,3
- srwi. r0,r0,2
- beq cr1,4f /* In place copy is not necessary */
- beq 7f /* Protect against 0 count */
- mtctr r0
- bge cr1,2f
-
- la r8,-4(r4)
- la r7,-4(r3)
-1: lwzu r0,4(r8)
- stwu r0,4(r7)
- bdnz 1b
- b 4f
-
-2: slwi r0,r0,2
- add r8,r4,r0
- add r7,r3,r0
-3: lwzu r0,-4(r8)
- stwu r0,-4(r7)
- bdnz 3b
-
-4:
-/* Unlock the data cache and invalidate locked area */
- xor r0, r0, r0
- mtspr 1011, r0
- lis r4, CONFIG_SYS_INIT_RAM_ADDR at h
- ori r4, r4, CONFIG_SYS_INIT_RAM_ADDR at l
- li r0, 128
- mtctr r0
-41:
- dcbi r0, r4
- addi r4, r4, 32
- bdnz 41b
-
-/*
- * Now flush the cache: note that we must start from a cache aligned
- * address. Otherwise we might miss one cache line.
- */
- cmpwi r6,0
- add r5,r3,r5
- beq 7f /* Always flush prefetch queue in any case */
- subi r0,r6,1
- andc r3,r3,r0
- mr r4,r3
-5: dcbst 0,r4
- add r4,r4,r6
- cmplw r4,r5
- blt 5b
- sync /* Wait for all dcbst to complete on bus */
- mr r4,r3
-6: icbi 0,r4
- add r4,r4,r6
- cmplw r4,r5
- blt 6b
-7: sync /* Wait for all icbi to complete on bus */
- isync
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-
- addi r0, r10, in_ram - _start + EXC_OFF_SYS_RESET
- mtlr r0
- blr
-
-in_ram:
-
- /*
- * Relocation Function, r12 point to got2+0x8000
- *
- * Adjust got2 pointers, no need to check for 0, this code
- * already puts a few entries in the table.
- */
- li r0,__got2_entries at sectoff@l
- la r3,GOT(_GOT2_TABLE_)
- lwz r11,GOT(_GOT2_TABLE_)
- mtctr r0
- sub r11,r3,r11
- addi r3,r3,-4
-1: lwzu r0,4(r3)
- cmpwi r0,0
- beq- 2f
- add r0,r0,r11
- stw r0,0(r3)
-2: bdnz 1b
-
- /*
- * Now adjust the fixups and the pointers to the fixups
- * in case we need to move ourselves again.
- */
- li r0,__fixup_entries at sectoff@l
- lwz r3,GOT(_FIXUP_TABLE_)
- cmpwi r0,0
- mtctr r0
- addi r3,r3,-4
- beq 4f
-3: lwzu r4,4(r3)
- lwzux r0,r4,r11
- cmpwi r0,0
- add r0,r0,r11
- stw r4,0(r3)
- beq- 5f
- stw r0,0(r4)
-5: bdnz 3b
-4:
-clear_bss:
- /*
- * Now clear BSS segment
- */
- lwz r3,GOT(__bss_start)
- lwz r4,GOT(__bss_end)
-
- cmplw 0, r3, r4
- beq 6f
-
- li r0, 0
-5:
- stw r0, 0(r3)
- addi r3, r3, 4
- cmplw 0, r3, r4
- blt 5b
-6:
-
- mr r3, r9 /* Global Data pointer */
- mr r4, r10 /* Destination Address */
- bl board_init_r
-
- /*
- * Copy exception vector code to low memory
- *
- * r3: dest_addr
- * r7: source address, r8: end address, r9: target address
- */
- .globl trap_init
-trap_init:
- mflr r4 /* save link register */
- GET_GOT
- lwz r7, GOT(_start)
- lwz r8, GOT(_end_of_vectors)
-
- li r9, 0x100 /* reset vector always at 0x100 */
-
- cmplw 0, r7, r8
- bgelr /* return if r7>=r8 - just in case */
-1:
- lwz r0, 0(r7)
- stw r0, 0(r9)
- addi r7, r7, 4
- addi r9, r9, 4
- cmplw 0, r7, r8
- bne 1b
-
- /*
- * relocate `hdlr' and `int_return' entries
- */
- li r7, .L_MachineCheck - _start + EXC_OFF_SYS_RESET
- li r8, Alignment - _start + EXC_OFF_SYS_RESET
-2:
- bl trap_reloc
- addi r7, r7, 0x100 /* next exception vector */
- cmplw 0, r7, r8
- blt 2b
-
- li r7, .L_Alignment - _start + EXC_OFF_SYS_RESET
- bl trap_reloc
-
- li r7, .L_ProgramCheck - _start + EXC_OFF_SYS_RESET
- bl trap_reloc
-
- li r7, .L_FPUnavailable - _start + EXC_OFF_SYS_RESET
- li r8, SystemCall - _start + EXC_OFF_SYS_RESET
-3:
- bl trap_reloc
- addi r7, r7, 0x100 /* next exception vector */
- cmplw 0, r7, r8
- blt 3b
-
- li r7, .L_SingleStep - _start + EXC_OFF_SYS_RESET
- li r8, _end_of_vectors - _start + EXC_OFF_SYS_RESET
-4:
- bl trap_reloc
- addi r7, r7, 0x100 /* next exception vector */
- cmplw 0, r7, r8
- blt 4b
-
- mtlr r4 /* restore link register */
- blr
-
- /* Setup the BAT registers.
- */
-setup_bats:
- lis r4, CONFIG_SYS_IBAT0L at h
- ori r4, r4, CONFIG_SYS_IBAT0L at l
- lis r3, CONFIG_SYS_IBAT0U at h
- ori r3, r3, CONFIG_SYS_IBAT0U at l
- mtspr IBAT0L, r4
- mtspr IBAT0U, r3
- isync
-
- lis r4, CONFIG_SYS_DBAT0L at h
- ori r4, r4, CONFIG_SYS_DBAT0L at l
- lis r3, CONFIG_SYS_DBAT0U at h
- ori r3, r3, CONFIG_SYS_DBAT0U at l
- mtspr DBAT0L, r4
- mtspr DBAT0U, r3
- isync
-
- lis r4, CONFIG_SYS_IBAT1L at h
- ori r4, r4, CONFIG_SYS_IBAT1L at l
- lis r3, CONFIG_SYS_IBAT1U at h
- ori r3, r3, CONFIG_SYS_IBAT1U at l
- mtspr IBAT1L, r4
- mtspr IBAT1U, r3
- isync
-
- lis r4, CONFIG_SYS_DBAT1L at h
- ori r4, r4, CONFIG_SYS_DBAT1L at l
- lis r3, CONFIG_SYS_DBAT1U at h
- ori r3, r3, CONFIG_SYS_DBAT1U at l
- mtspr DBAT1L, r4
- mtspr DBAT1U, r3
- isync
-
- lis r4, CONFIG_SYS_IBAT2L at h
- ori r4, r4, CONFIG_SYS_IBAT2L at l
- lis r3, CONFIG_SYS_IBAT2U at h
- ori r3, r3, CONFIG_SYS_IBAT2U at l
- mtspr IBAT2L, r4
- mtspr IBAT2U, r3
- isync
-
- lis r4, CONFIG_SYS_DBAT2L at h
- ori r4, r4, CONFIG_SYS_DBAT2L at l
- lis r3, CONFIG_SYS_DBAT2U at h
- ori r3, r3, CONFIG_SYS_DBAT2U at l
- mtspr DBAT2L, r4
- mtspr DBAT2U, r3
- isync
-
- lis r4, CONFIG_SYS_IBAT3L at h
- ori r4, r4, CONFIG_SYS_IBAT3L at l
- lis r3, CONFIG_SYS_IBAT3U at h
- ori r3, r3, CONFIG_SYS_IBAT3U at l
- mtspr IBAT3L, r4
- mtspr IBAT3U, r3
- isync
-
- lis r4, CONFIG_SYS_DBAT3L at h
- ori r4, r4, CONFIG_SYS_DBAT3L at l
- lis r3, CONFIG_SYS_DBAT3U at h
- ori r3, r3, CONFIG_SYS_DBAT3U at l
- mtspr DBAT3L, r4
- mtspr DBAT3U, r3
- isync
-
- /* Invalidate TLBs.
- * -> for (val = 0; val < 0x20000; val+=0x1000)
- * -> tlbie(val);
- */
- lis r3, 0
- lis r5, 2
-
-1:
- tlbie r3
- addi r3, r3, 0x1000
- cmp 0, 0, r3, r5
- blt 1b
-
- blr
diff --git a/arch/powerpc/cpu/mpc824x/traps.c b/arch/powerpc/cpu/mpc824x/traps.c
deleted file mode 100644
index 6abf41d..0000000
--- a/arch/powerpc/cpu/mpc824x/traps.c
+++ /dev/null
@@ -1,194 +0,0 @@
-/*
- * linux/arch/powerpc/kernel/traps.c
- *
- * Copyright (C) 1995-1996 Gary Thomas (gdt at linuxppc.org)
- *
- * Modified by Cort Dougan (cort at cs.nmt.edu)
- * and Paul Mackerras (paulus at cs.anu.edu.au)
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * This file handles the architecture-dependent parts of hardware exceptions
- */
-
-#include <common.h>
-#include <asm/processor.h>
-
-/* Returns 0 if exception not found and fixup otherwise. */
-extern unsigned long search_exception_table(unsigned long);
-
-/* THIS NEEDS CHANGING to use the board info structure.
-*/
-#define END_OF_MEM 0x00400000
-
-/*
- * Trap & Exception support
- */
-
-static void print_backtrace(unsigned long *sp)
-{
- int cnt = 0;
- unsigned long i;
-
- printf("Call backtrace: ");
- while (sp) {
- if ((uint)sp > END_OF_MEM)
- break;
-
- i = sp[1];
- if (cnt++ % 7 == 0)
- printf("\n");
- printf("%08lX ", i);
- if (cnt > 32) break;
- sp = (unsigned long *)*sp;
- }
- printf("\n");
-}
-
-void show_regs(struct pt_regs *regs)
-{
- int i;
-
- printf("NIP: %08lX XER: %08lX LR: %08lX REGS: %p TRAP: %04lx DAR: %08lX\n",
- regs->nip, regs->xer, regs->link, regs, regs->trap, regs->dar);
- printf("MSR: %08lx EE: %01x PR: %01x FP: %01x ME: %01x IR/DR: %01x%01x\n",
- regs->msr, regs->msr&MSR_EE ? 1 : 0, regs->msr&MSR_PR ? 1 : 0,
- regs->msr & MSR_FP ? 1 : 0,regs->msr&MSR_ME ? 1 : 0,
- regs->msr&MSR_IR ? 1 : 0,
- regs->msr&MSR_DR ? 1 : 0);
-
- printf("\n");
- for (i = 0; i < 32; i++) {
- if ((i % 8) == 0)
- {
- printf("GPR%02d: ", i);
- }
-
- printf("%08lX ", regs->gpr[i]);
- if ((i % 8) == 7)
- {
- printf("\n");
- }
- }
-}
-
-
-static void _exception(int signr, struct pt_regs *regs)
-{
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Exception in kernel pc %lx signal %d",regs->nip,signr);
-}
-
-void MachineCheckException(struct pt_regs *regs)
-{
- unsigned long fixup;
-
- /* Probing PCI using config cycles cause this exception
- * when a device is not present. Catch it and return to
- * the PCI exception handler.
- */
- if ((fixup = search_exception_table(regs->nip)) != 0) {
- regs->nip = fixup;
- return;
- }
-
- printf("Machine check in kernel mode.\n");
- printf("Caused by (from msr): ");
- printf("regs %p ",regs);
- switch( regs->msr & 0x000F0000) {
- case (0x80000000>>12):
- printf("Machine check signal - probably due to mm fault\n"
- "with mmu off\n");
- break;
- case (0x80000000>>13):
- printf("Transfer error ack signal\n");
- break;
- case (0x80000000>>14):
- printf("Data parity signal\n");
- break;
- case (0x80000000>>15):
- printf("Address parity signal\n");
- break;
- default:
- printf("Unknown values in msr\n");
- }
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("machine check");
-}
-
-void AlignmentException(struct pt_regs *regs)
-{
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Alignment Exception");
-}
-
-void ProgramCheckException(struct pt_regs *regs)
-{
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Program Check Exception");
-}
-
-void SoftEmuException(struct pt_regs *regs)
-{
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Software Emulation Exception");
-}
-
-
-void UnknownException(struct pt_regs *regs)
-{
- printf("Bad trap at PC: %lx, SR: %lx, vector=%lx\n",
- regs->nip, regs->msr, regs->trap);
- _exception(0, regs);
-}
-
-#if defined(CONFIG_CMD_BEDBUG)
-extern void do_bedbug_breakpoint(struct pt_regs *);
-#endif
-
-void DebugException(struct pt_regs *regs)
-{
-
- printf("Debugger trap at @ %lx\n", regs->nip );
- show_regs(regs);
-#if defined(CONFIG_CMD_BEDBUG)
- do_bedbug_breakpoint( regs );
-#endif
-}
-
-/* Probe an address by reading. If not present, return -1, otherwise
- * return 0.
- */
-int addr_probe(uint *addr)
-{
-#if 0
- int retval;
-
- __asm__ __volatile__( \
- "1: lwz %0,0(%1)\n" \
- " eieio\n" \
- " li %0,0\n" \
- "2:\n" \
- ".section .fixup,\"ax\"\n" \
- "3: li %0,-1\n" \
- " b 2b\n" \
- ".section __ex_table,\"a\"\n" \
- " .align 2\n" \
- " .long 1b,3b\n" \
- ".text" \
- : "=r" (retval) : "r"(addr));
-
- return (retval);
-#endif
- return 0;
-}
diff --git a/arch/powerpc/cpu/mpc824x/u-boot.lds b/arch/powerpc/cpu/mpc824x/u-boot.lds
deleted file mode 100644
index 04aba84..0000000
--- a/arch/powerpc/cpu/mpc824x/u-boot.lds
+++ /dev/null
@@ -1,76 +0,0 @@
-/*
- * (C) Copyright 2001-2010
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- .text :
- {
- arch/powerpc/cpu/mpc824x/start.o (.text*)
- *(.text*)
- . = ALIGN(16);
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 2ed51b1..db8cc8c 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -1360,8 +1360,6 @@ void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val);
#elif defined(CONFIG_MPC8260)
#define _machine _MACH_8260
#define have_of 0
-#elif defined(CONFIG_SANDPOINT)
-#define _machine _MACH_sandpoint
#else
#error "Machine not defined correctly"
#endif
diff --git a/board/a3000/Kconfig b/board/a3000/Kconfig
deleted file mode 100644
index 21a9e48..0000000
--- a/board/a3000/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_A3000
-
-config SYS_BOARD
- default "a3000"
-
-config SYS_CONFIG_NAME
- default "A3000"
-
-endif
diff --git a/board/a3000/MAINTAINERS b/board/a3000/MAINTAINERS
deleted file mode 100644
index 303e5fd..0000000
--- a/board/a3000/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-A3000 BOARD
-#M: -
-S: Maintained
-F: board/a3000/
-F: include/configs/A3000.h
-F: configs/A3000_defconfig
diff --git a/board/a3000/Makefile b/board/a3000/Makefile
deleted file mode 100644
index 9b9b048..0000000
--- a/board/a3000/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = a3000.o flash.o
diff --git a/board/a3000/README b/board/a3000/README
deleted file mode 100644
index f0e92c5..0000000
--- a/board/a3000/README
+++ /dev/null
@@ -1,17 +0,0 @@
-U-Boot for Artis SBC-A3000
----------------------------
-
-Artis SBC-A3000 has one flash socket that the user uses Intel 28F128J3A (16MB)
-or 28F064J3A (8MB) chips.
-
-In board's notation, bank 0 is the one at the address of 0xFF000000.
-bank 1 is the one at the address of 0xFF800000
-
-On power-up the processor jumps to the address of 0xFFF00100, the last
-megabyte of the bank 0 of flash.
-
-Thus, U-Boot is configured to reside in flash starting at the address of
-0xFFF00000. The environment space is located in flash separately from
-U-Boot, at the address of 0xFFFE0000.
-
-There is a National ns83815 10/100M ethernet controller on-board.
diff --git a/board/a3000/a3000.c b/board/a3000/a3000.c
deleted file mode 100644
index 3e2f6b0..0000000
--- a/board/a3000/a3000.c
+++ /dev/null
@@ -1,101 +0,0 @@
-/*
- * (C) Copyright 2001
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * Modified during 2003 by
- * Ken Chou, kchou at ieee.org
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <pci.h>
-#include <netdev.h>
-
-int checkboard (void)
-{
- ulong busfreq = get_bus_freq(0);
- char buf[32];
-
- printf("Board: A3000 Local Bus at %s MHz\n", strmhz(buf, busfreq));
- return 0;
-
-}
-
-phys_size_t initdram (int board_type)
-{
- long size;
- long new_bank0_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-/*
- * Initialize PCI Devices
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_a3000_config_table[] = {
- /* vendor, device, class */
- /* bus, dev, func */
- { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_83815, PCI_ANY_ID,
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, /* dp83815 eth0 divice */
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- PCI_ANY_ID, 0x14, PCI_ANY_ID, /* PCI slot1 */
- pci_cfgfunc_config_device, { PCI_ENET1_IOADDR,
- PCI_ENET1_MEMADDR,
- PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- PCI_ANY_ID, 0x15, PCI_ANY_ID, /* PCI slot2 */
- pci_cfgfunc_config_device, { PCI_ENET2_IOADDR,
- PCI_ENET2_MEMADDR,
- PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- PCI_ANY_ID, 0x16, PCI_ANY_ID, /* PCI slot3 */
- pci_cfgfunc_config_device, { PCI_ENET3_IOADDR,
- PCI_ENET3_MEMADDR,
- PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER }},
- { }
-};
-#endif
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_a3000_config_table,
-#endif
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/board/a3000/flash.c b/board/a3000/flash.c
deleted file mode 100644
index f2dd3c2..0000000
--- a/board/a3000/flash.c
+++ /dev/null
@@ -1,438 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#include <common.h>
-#include <mpc824x.h>
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-
-/*---------------------------------------------------------------------*/
-#define DEBUG_FLASH
-
-#ifdef DEBUG_FLASH
-#define DEBUGF(fmt,args...) printf(fmt ,##args)
-#else
-#define DEBUGF(fmt,args...)
-#endif
-/*---------------------------------------------------------------------*/
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_char *addr, flash_info_t *info);
-static int write_data (flash_info_t *info, uchar *dest, uchar data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-#define BS(b) (b)
-#define BYTEME(x) ((x) & 0xFF)
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- unsigned long flash_banks[CONFIG_SYS_MAX_FLASH_BANKS] = CONFIG_SYS_FLASH_BANKS;
- unsigned long size, size_b[CONFIG_SYS_MAX_FLASH_BANKS];
-
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i)
- {
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
- DEBUGF("Get flash bank %d @ 0x%08lx\n", i, flash_banks[i]);
-/*
- size_b[i] = flash_get_size((vu_char *)flash_banks[i], &flash_info[i]);
-*/
- size_b[i] = flash_get_size((vu_char *) 0xff800000 , &flash_info[i]);
-
- if (flash_info[i].flash_id == FLASH_UNKNOWN)
- {
- printf ("## Unknown FLASH on Bank %d: "
- "ID 0x%lx, Size = 0x%08lx = %ld MB\n",
- i, flash_info[i].flash_id,
- size_b[i], size_b[i]<<20);
- }
- else
- {
- DEBUGF("## Flash bank %d@0x%08lx sizes: 0x%08lx \n",
- i, flash_banks[i], size_b[i]);
-
- flash_get_offsets (flash_banks[i], &flash_info[i]);
- flash_info[i].size = size_b[i];
- }
- }
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- DEBUGF("protect monitor %x @ %x\n", CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_LEN);
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- DEBUGF("protect environtment %x @ %x\n", CONFIG_ENV_ADDR, CONFIG_ENV_SECT_SIZE);
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1,
- &flash_info[0]);
-#endif
-
- size = 0;
- DEBUGF("## Final Flash bank sizes: ");
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i)
- {
- DEBUGF("%08lx ", size_b[i]);
- size += size_b[i];
- }
- DEBUGF("\n");
- return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- base += 0x00020000; /* 128k per bank */
- }
- return;
-
- default:
- printf ("Don't know sector ofsets for flash type 0x%lx\n", info->flash_id);
- return;
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_FUJ: printf ("Fujitsu "); break;
- case FLASH_MAN_SST: printf ("SST "); break;
- case FLASH_MAN_STM: printf ("STM "); break;
- case FLASH_MAN_INTEL: printf ("Intel "); break;
- case FLASH_MAN_MT: printf ("MT "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F320J3A:
- printf ("28F320J3A (32Mbit = 128K x 32)\n");
- break;
- case FLASH_28F640J3A:
- printf ("28F640J3A (64Mbit = 128K x 64)\n");
- break;
- case FLASH_28F128J3A:
- printf ("28F128J3A (128Mbit = 128K x 128)\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
-#if 1
- if (info->size >= (1 << 20)) {
- i = 20;
- } else {
- i = 10;
- }
- printf (" Size: %ld %cB in %d Sectors\n",
- info->size >> i,
- (i == 20) ? 'M' : 'k',
- info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
-#endif
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (vu_char *addr, flash_info_t *info)
-{
- vu_char manuf, device;
-
- addr[0] = BS(0x90);
- manuf = BS(addr[0]);
- DEBUGF("Manuf. ID @ 0x%08lx: 0x%08x\n", (ulong)addr, manuf);
-
- switch (manuf) {
- case BYTEME(AMD_MANUFACT):
- info->flash_id = FLASH_MAN_AMD;
- break;
- case BYTEME(FUJ_MANUFACT):
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case BYTEME(SST_MANUFACT):
- info->flash_id = FLASH_MAN_SST;
- break;
- case BYTEME(STM_MANUFACT):
- info->flash_id = FLASH_MAN_STM;
- break;
- case BYTEME(INTEL_MANUFACT):
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = BS(0xFF); /* restore read mode, (yes, BS is a NOP) */
- return 0; /* no or unknown flash */
- }
-
- device = BS(addr[2]); /* device ID */
-
- DEBUGF("Device ID @ 0x%08lx: 0x%08x\n", (ulong)(&addr[1]), device);
-
- switch (device) {
- case BYTEME(INTEL_ID_28F320J3A):
- info->flash_id += FLASH_28F320J3A;
- info->sector_count = 32;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case BYTEME(INTEL_ID_28F640J3A):
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case BYTEME(INTEL_ID_28F128J3A):
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- addr[0] = BS(0xFF); /* restore read mode (yes, a NOP) */
- return 0; /* => no or unknown flash */
-
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = BS(0xFF); /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) {
- printf ("Can erase only Intel flash types - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_char *addr = (vu_char *)(info->start[sect]);
- unsigned long status;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = BS(0x50); /* clear status register */
- *addr = BS(0x20); /* erase setup */
- *addr = BS(0xD0); /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag) {
- enable_interrupts();
- }
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((status = BS(*addr)) & BYTEME(0x00800080)) != BYTEME(0x00800080)) {
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = BS(0xB0); /* suspend erase */
- *addr = BS(0xFF); /* reset to read mode */
- return 1;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- *addr = BS(0xFF); /* reset to read mode */
- }
- }
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-#define FLASH_WIDTH 1 /* flash bus width in bytes */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- uchar *wp = (uchar *)addr;
- int rc;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
- while (cnt > 0) {
- if ((rc = write_data(info, wp, *src)) != 0) {
- return rc;
- }
- wp++;
- src++;
- cnt--;
- }
-
- return cnt;
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t *info, uchar *dest, uchar data)
-{
- vu_char *addr = (vu_char *)dest;
- ulong status;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((BS(*addr) & data) != data) {
- return 2;
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = BS(0x40); /* write setup */
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag) {
- enable_interrupts();
- }
-
- start = get_timer (0);
-
- while (((status = BS(*addr)) & BYTEME(0x00800080)) != BYTEME(0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = BS(0xFF); /* restore read mode */
- return 1;
- }
- }
-
- *addr = BS(0xFF); /* restore read mode */
-
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/cpc45/Kconfig b/board/cpc45/Kconfig
deleted file mode 100644
index c564caf..0000000
--- a/board/cpc45/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_CPC45
-
-config SYS_BOARD
- default "cpc45"
-
-config SYS_CONFIG_NAME
- default "CPC45"
-
-endif
diff --git a/board/cpc45/MAINTAINERS b/board/cpc45/MAINTAINERS
deleted file mode 100644
index 163e09c..0000000
--- a/board/cpc45/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-CPC45 BOARD
-M: Josef Wagner <Wagner@Microsys.de>
-S: Maintained
-F: board/cpc45/
-F: include/configs/CPC45.h
-F: configs/CPC45_defconfig
-F: configs/CPC45_ROMBOOT_defconfig
diff --git a/board/cpc45/Makefile b/board/cpc45/Makefile
deleted file mode 100644
index 1310f93..0000000
--- a/board/cpc45/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = cpc45.o flash.o plx9030.o pd67290.o ide.o
diff --git a/board/cpc45/cpc45.c b/board/cpc45/cpc45.c
deleted file mode 100644
index f182e79..0000000
--- a/board/cpc45/cpc45.c
+++ /dev/null
@@ -1,250 +0,0 @@
-/*
- * (C) Copyright 2001
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <pci.h>
-#include <i2c.h>
-#include <netdev.h>
-
-int sysControlDisplay(int digit, uchar ascii_code);
-extern void Plx9030Init(void);
-extern void SPD67290Init(void);
-
- /* We have to clear the initial data area here. Couldn't have done it
- * earlier because DRAM had not been initialized.
- */
-int board_early_init_f(void)
-{
-
- /* enable DUAL UART Mode on CPC45 */
- *(uchar*)DUART_DCR |= 0x1; /* set DCM bit */
-
- return 0;
-}
-
-int checkboard(void)
-{
-/*
- char revision = BOARD_REV;
-*/
- ulong busfreq = get_bus_freq(0);
- char buf[32];
-
- puts ("CPC45 ");
-/*
- printf("Revision %d ", revision);
-*/
- printf("Local Bus at %s MHz\n", strmhz(buf, busfreq));
-
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- int m, row, col, bank, i, ref;
- unsigned long start, end;
- uint32_t mccr1, mccr2;
- uint32_t mear1 = 0, emear1 = 0, msar1 = 0, emsar1 = 0;
- uint32_t mear2 = 0, emear2 = 0, msar2 = 0, emsar2 = 0;
- uint8_t mber = 0;
- unsigned int tmp;
-
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
- if (i2c_reg_read (0x50, 2) != 0x04)
- return 0; /* Memory type */
-
- m = i2c_reg_read (0x50, 5); /* # of physical banks */
- row = i2c_reg_read (0x50, 3); /* # of rows */
- col = i2c_reg_read (0x50, 4); /* # of columns */
- bank = i2c_reg_read (0x50, 17); /* # of logical banks */
- ref = i2c_reg_read (0x50, 12); /* refresh rate / type */
-
- CONFIG_READ_WORD(MCCR1, mccr1);
- mccr1 &= 0xffff0000;
-
- CONFIG_READ_WORD(MCCR2, mccr2);
- mccr2 &= 0xffff0000;
-
- start = CONFIG_SYS_SDRAM_BASE;
- end = start + (1 << (col + row + 3) ) * bank - 1;
-
- for (i = 0; i < m; i++) {
- mccr1 |= ((row == 13)? 2 : (bank == 4)? 0 : 3) << i * 2;
- if (i < 4) {
- msar1 |= ((start >> 20) & 0xff) << i * 8;
- emsar1 |= ((start >> 28) & 0xff) << i * 8;
- mear1 |= ((end >> 20) & 0xff) << i * 8;
- emear1 |= ((end >> 28) & 0xff) << i * 8;
- } else {
- msar2 |= ((start >> 20) & 0xff) << (i-4) * 8;
- emsar2 |= ((start >> 28) & 0xff) << (i-4) * 8;
- mear2 |= ((end >> 20) & 0xff) << (i-4) * 8;
- emear2 |= ((end >> 28) & 0xff) << (i-4) * 8;
- }
- mber |= 1 << i;
- start += (1 << (col + row + 3) ) * bank;
- end += (1 << (col + row + 3) ) * bank;
- }
- for (; i < 8; i++) {
- if (i < 4) {
- msar1 |= 0xff << i * 8;
- emsar1 |= 0x30 << i * 8;
- mear1 |= 0xff << i * 8;
- emear1 |= 0x30 << i * 8;
- } else {
- msar2 |= 0xff << (i-4) * 8;
- emsar2 |= 0x30 << (i-4) * 8;
- mear2 |= 0xff << (i-4) * 8;
- emear2 |= 0x30 << (i-4) * 8;
- }
- }
-
- switch(ref) {
- case 0x00:
- case 0x80:
- tmp = get_bus_freq(0) / 1000000 * 15625 / 1000 - 22;
- break;
- case 0x01:
- case 0x81:
- tmp = get_bus_freq(0) / 1000000 * 3900 / 1000 - 22;
- break;
- case 0x02:
- case 0x82:
- tmp = get_bus_freq(0) / 1000000 * 7800 / 1000 - 22;
- break;
- case 0x03:
- case 0x83:
- tmp = get_bus_freq(0) / 1000000 * 31300 / 1000 - 22;
- break;
- case 0x04:
- case 0x84:
- tmp = get_bus_freq(0) / 1000000 * 62500 / 1000 - 22;
- break;
- case 0x05:
- case 0x85:
- tmp = get_bus_freq(0) / 1000000 * 125000 / 1000 - 22;
- break;
- default:
- tmp = 0x512;
- break;
- }
-
- CONFIG_WRITE_WORD(MCCR1, mccr1);
- CONFIG_WRITE_WORD(MCCR2, tmp << MCCR2_REFINT_SHIFT);
- CONFIG_WRITE_WORD(MSAR1, msar1);
- CONFIG_WRITE_WORD(EMSAR1, emsar1);
- CONFIG_WRITE_WORD(MEAR1, mear1);
- CONFIG_WRITE_WORD(EMEAR1, emear1);
- CONFIG_WRITE_WORD(MSAR2, msar2);
- CONFIG_WRITE_WORD(EMSAR2, emsar2);
- CONFIG_WRITE_WORD(MEAR2, mear2);
- CONFIG_WRITE_WORD(EMEAR2, emear2);
- CONFIG_WRITE_BYTE(MBER, mber);
-
- return (1 << (col + row + 3) ) * bank * m;
-}
-
-
-/*
- * Initialize PCI Devices, report devices found.
- */
-
-static struct pci_config_table pci_cpc45_config_table[] = {
-#ifndef CONFIG_PCI_PNP
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0F, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0D, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_PLX9030_IOADDR,
- PCI_PLX9030_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0E, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCMCIA_IO_BASE,
- PCMCIA_IO_BASE,
- PCI_COMMAND_MEMORY | PCI_COMMAND_IO }},
-#endif /*CONFIG_PCI_PNP*/
- { }
-};
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_cpc45_config_table,
-#endif
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-
- /* init PCI_to_LOCAL Bus BRIDGE */
- Plx9030Init();
-
- /* Clear Display */
- DISP_CWORD = 0x0;
-
- sysControlDisplay(0,' ');
- sysControlDisplay(1,'C');
- sysControlDisplay(2,'P');
- sysControlDisplay(3,'C');
- sysControlDisplay(4,' ');
- sysControlDisplay(5,'4');
- sysControlDisplay(6,'5');
- sysControlDisplay(7,' ');
-
-}
-
-/**************************************************************************
-*
-* sysControlDisplay - controls one of the Alphanum. Display digits.
-*
-* This routine will write an ASCII character to the display digit requested.
-*
-* SEE ALSO:
-*
-* RETURNS: NA
-*/
-
-int sysControlDisplay (int digit, /* number of digit 0..7 */
- uchar ascii_code /* ASCII code */
- )
-{
- if ((digit < 0) || (digit > 7))
- return (-1);
-
- *((volatile uchar *) (DISP_CHR_RAM + digit)) = ascii_code;
-
- return (0);
-}
-
-#if defined(CONFIG_CMD_PCMCIA)
-
-#ifdef CONFIG_SYS_PCMCIA_MEM_ADDR
-volatile unsigned char *pcmcia_mem = (unsigned char*)CONFIG_SYS_PCMCIA_MEM_ADDR;
-#endif
-
-int pcmcia_init(void)
-{
- u_int rc;
-
- debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- rc = i82365_init();
-
- return rc;
-}
-
-#endif
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/board/cpc45/flash.c b/board/cpc45/flash.c
deleted file mode 100644
index 917db34..0000000
--- a/board/cpc45/flash.c
+++ /dev/null
@@ -1,506 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-#define FLASH_BANK_SIZE 0x800000
-#define MAIN_SECT_SIZE 0x40000
-#define PARAM_SECT_SIZE 0x8000
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-static int write_data (flash_info_t * info, ulong dest, ulong * data);
-static void write_via_fpu (vu_long * addr, ulong * data);
-static __inline__ unsigned long get_msr (void);
-static __inline__ void set_msr (unsigned long msr);
-
-/*---------------------------------------------------------------------*/
-#undef DEBUG_FLASH
-
-/*---------------------------------------------------------------------*/
-#ifdef DEBUG_FLASH
-#define DEBUGF(fmt,args...) printf(fmt ,##args)
-#else
-#define DEBUGF(fmt,args...)
-#endif
-/*---------------------------------------------------------------------*/
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i, j;
- ulong size = 0;
- uchar tempChar;
- vu_long *tmpaddr;
-
- /* Enable flash writes on CPC45 */
-
- tempChar = BOARD_CTRL;
-
- tempChar |= (B_CTRL_FWPT_1 | B_CTRL_FWRE_1);
-
- tempChar &= ~(B_CTRL_FWPT_0 | B_CTRL_FWRE_0);
-
- BOARD_CTRL = tempChar;
-
- __asm__ volatile ("sync\n eieio");
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- vu_long *addr = (vu_long *) (CONFIG_SYS_FLASH_BASE + i * FLASH_BANK_SIZE);
-
- addr[0] = 0x00900090;
-
- __asm__ volatile ("sync\n eieio");
-
- udelay (100);
-
- DEBUGF ("Flash bank # %d:\n"
- "\tManuf. ID @ 0x%08lX: 0x%08lX\n"
- "\tDevice ID @ 0x%08lX: 0x%08lX\n",
- i,
- (ulong) (&addr[0]), addr[0],
- (ulong) (&addr[2]), addr[2]);
-
-
- if ((addr[0] == addr[1]) && (addr[0] == INTEL_MANUFACT) &&
- (addr[2] == addr[3]) && (addr[2] == INTEL_ID_28F160F3T)) {
-
- flash_info[i].flash_id =
- (FLASH_MAN_INTEL & FLASH_VENDMASK) |
- (INTEL_ID_28F160F3T & FLASH_TYPEMASK);
-
- } else if ((addr[0] == addr[1]) && (addr[0] == INTEL_MANUFACT)
- && (addr[2] == addr[3])
- && (addr[2] == INTEL_ID_28F160C3T)) {
-
- flash_info[i].flash_id =
- (FLASH_MAN_INTEL & FLASH_VENDMASK) |
- (INTEL_ID_28F160C3T & FLASH_TYPEMASK);
-
- } else {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- addr[0] = 0xFFFFFFFF;
- goto Done;
- }
-
- DEBUGF ("flash_id = 0x%08lX\n", flash_info[i].flash_id);
-
- addr[0] = 0xFFFFFFFF;
-
- flash_info[i].size = FLASH_BANK_SIZE;
- flash_info[i].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- memset (flash_info[i].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
- for (j = 0; j < flash_info[i].sector_count; j++) {
- if (j > 30) {
- flash_info[i].start[j] = CONFIG_SYS_FLASH_BASE +
- i * FLASH_BANK_SIZE +
- (MAIN_SECT_SIZE * 31) + (j -
- 31) *
- PARAM_SECT_SIZE;
- } else {
- flash_info[i].start[j] = CONFIG_SYS_FLASH_BASE +
- i * FLASH_BANK_SIZE +
- j * MAIN_SECT_SIZE;
- }
- }
-
- /* unlock sectors, if 160C3T */
-
- for (j = 0; j < flash_info[i].sector_count; j++) {
- tmpaddr = (vu_long *) flash_info[i].start[j];
-
- if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
- (INTEL_ID_28F160C3T & FLASH_TYPEMASK)) {
- tmpaddr[0] = 0x00600060;
- tmpaddr[0] = 0x00D000D0;
- tmpaddr[1] = 0x00600060;
- tmpaddr[1] = 0x00D000D0;
- }
- }
-
- size += flash_info[i].size;
-
- addr[0] = 0x00FF00FF;
- addr[1] = 0x00FF00FF;
- }
-
- /* Protect monitor and environment sectors
- */
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE + FLASH_BANK_SIZE
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[1]);
-#else
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
-#if CONFIG_ENV_ADDR >= CONFIG_SYS_FLASH_BASE + FLASH_BANK_SIZE
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[1]);
-#else
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-#endif
-#endif
-
-Done:
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- switch ((i = info->flash_id & FLASH_VENDMASK)) {
- case (FLASH_MAN_INTEL & FLASH_VENDMASK):
- printf ("Intel: ");
- break;
- default:
- printf ("Unknown Vendor 0x%04x ", i);
- break;
- }
-
- switch ((i = info->flash_id & FLASH_TYPEMASK)) {
- case (INTEL_ID_28F160F3T & FLASH_TYPEMASK):
- printf ("28F160F3T (16Mbit)\n");
- break;
-
- case (INTEL_ID_28F160C3T & FLASH_TYPEMASK):
- printf ("28F160C3T (16Mbit)\n");
- break;
-
- default:
- printf ("Unknown Chip Type 0x%04x\n", i);
- goto Done;
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; i++) {
- if ((i % 5) == 0) {
- printf ("\n ");
- }
- printf (" %08lX%s", info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
-
-Done:
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- DEBUGF ("Erase flash bank %d sect %d ... %d\n",
- info - &flash_info[0], s_first, s_last);
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) !=
- (FLASH_MAN_INTEL & FLASH_VENDMASK)) {
- printf ("Can erase only Intel flash types - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_long *addr = (vu_long *) (info->start[sect]);
-
- DEBUGF ("Erase sect %d @ 0x%08lX\n",
- sect, (ulong) addr);
-
- /* Disable interrupts which might cause a timeout
- * here.
- */
- flag = disable_interrupts ();
-
- addr[0] = 0x00500050; /* clear status register */
- addr[0] = 0x00200020; /* erase setup */
- addr[0] = 0x00D000D0; /* erase confirm */
-
- addr[1] = 0x00500050; /* clear status register */
- addr[1] = 0x00200020; /* erase setup */
- addr[1] = 0x00D000D0; /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((addr[0] & 0x00800080) != 0x00800080) ||
- ((addr[1] & 0x00800080) != 0x00800080)) {
- if ((now = get_timer (start)) >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- addr[0] = 0x00B000B0; /* suspend erase */
- addr[0] = 0x00FF00FF; /* to read mode */
- return 1;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- addr[0] = 0x00FF00FF;
- }
- }
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-#define FLASH_WIDTH 8 /* flash bus width in bytes */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong wp, cp, msr;
- int l, rc, i;
- ulong data[2];
- ulong *datah = &data[0];
- ulong *datal = &data[1];
-
- DEBUGF ("Flash write_buff: @ 0x%08lx, src 0x%08lx len %ld\n",
- addr, (ulong) src, cnt);
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
- msr = get_msr ();
- set_msr (msr | MSR_FP);
-
- wp = (addr & ~(FLASH_WIDTH - 1)); /* get lower aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- *datah = *datal = 0;
-
- for (i = 0, cp = wp; i < l; i++, cp++) {
- if (i >= 4) {
- *datah = (*datah << 8) |
- ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datal << 8) | (*(uchar *) cp);
- }
- for (; i < FLASH_WIDTH && cnt > 0; ++i) {
- char tmp = *src++;
-
- if (i >= 4) {
- *datah = (*datah << 8) |
- ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datal << 8) | tmp;
- --cnt;
- ++cp;
- }
-
- for (; cnt == 0 && i < FLASH_WIDTH; ++i, ++cp) {
- if (i >= 4) {
- *datah = (*datah << 8) |
- ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datah << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, data)) != 0) {
- set_msr (msr);
- return (rc);
- }
-
- wp += FLASH_WIDTH;
- }
-
- /*
- * handle FLASH_WIDTH aligned part
- */
- while (cnt >= FLASH_WIDTH) {
- *datah = *(ulong *) src;
- *datal = *(ulong *) (src + 4);
- if ((rc = write_data (info, wp, data)) != 0) {
- set_msr (msr);
- return (rc);
- }
- wp += FLASH_WIDTH;
- cnt -= FLASH_WIDTH;
- src += FLASH_WIDTH;
- }
-
- if (cnt == 0) {
- set_msr (msr);
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- *datah = *datal = 0;
- for (i = 0, cp = wp; i < FLASH_WIDTH && cnt > 0; ++i, ++cp) {
- char tmp = *src++;
-
- if (i >= 4) {
- *datah = (*datah << 8) | ((*datal & 0xFF000000) >>
- 24);
- }
-
- *datal = (*datal << 8) | tmp;
- --cnt;
- }
-
- for (; i < FLASH_WIDTH; ++i, ++cp) {
- if (i >= 4) {
- *datah = (*datah << 8) | ((*datal & 0xFF000000) >>
- 24);
- }
-
- *datal = (*datal << 8) | (*(uchar *) cp);
- }
-
- rc = write_data (info, wp, data);
- set_msr (msr);
-
- return (rc);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, ulong * data)
-{
- vu_long *addr = (vu_long *) dest;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if (((addr[0] & data[0]) != data[0]) ||
- ((addr[1] & data[1]) != data[1])) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- addr[0] = 0x00400040; /* write setup */
- write_via_fpu (addr, data);
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- start = get_timer (0);
-
- while (((addr[0] & 0x00800080) != 0x00800080) ||
- ((addr[1] & 0x00800080) != 0x00800080)) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- addr[0] = 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
-
- addr[0] = 0x00FF00FF; /* restore read mode */
-
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void write_via_fpu (vu_long * addr, ulong * data)
-{
- __asm__ __volatile__ ("lfd 1, 0(%0)"::"r" (data));
- __asm__ __volatile__ ("stfd 1, 0(%0)"::"r" (addr));
-}
-
-/*-----------------------------------------------------------------------
- */
-static __inline__ unsigned long get_msr (void)
-{
- unsigned long msr;
-
- __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
-
- return msr;
-}
-
-static __inline__ void set_msr (unsigned long msr)
-{
- __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
-}
diff --git a/board/cpc45/ide.c b/board/cpc45/ide.c
deleted file mode 100644
index 1944e36..0000000
--- a/board/cpc45/ide.c
+++ /dev/null
@@ -1,128 +0,0 @@
-/*
- * (C) Copyright 2001
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * (C) Copyright 2000-2011
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ide.h>
-#include <ata.h>
-#include <asm/io.h>
-
-#define EIEIO __asm__ volatile ("eieio")
-#define SYNC __asm__ volatile ("sync")
-
-void ide_input_swap_data(int dev, ulong *sect_buf, int words)
-{
- uchar i;
- volatile uchar *pbuf_even =
- (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
- volatile uchar *pbuf_odd =
- (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
- ushort *dbuf = (ushort *) sect_buf;
-
- while (words--) {
- for (i = 0; i < 2; i++) {
- *(((uchar *) (dbuf)) + 1) = *pbuf_even;
- *(uchar *) dbuf = *pbuf_odd;
- dbuf += 1;
- }
- }
-}
-
-void ide_input_data(int dev, ulong *sect_buf, int words)
-{
- uchar *dbuf;
- volatile uchar *pbuf_even;
- volatile uchar *pbuf_odd;
-
- pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
- pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
- dbuf = (uchar *) sect_buf;
- while (words--) {
- *dbuf++ = *pbuf_even;
- EIEIO;
- SYNC;
- *dbuf++ = *pbuf_odd;
- EIEIO;
- SYNC;
- *dbuf++ = *pbuf_even;
- EIEIO;
- SYNC;
- *dbuf++ = *pbuf_odd;
- EIEIO;
- SYNC;
- }
-}
-
-void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts)
-{
- uchar *dbuf;
- volatile uchar *pbuf_even;
- volatile uchar *pbuf_odd;
-
- pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
- pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
- dbuf = (uchar *) sect_buf;
- while (shorts--) {
- EIEIO;
- *dbuf++ = *pbuf_even;
- EIEIO;
- *dbuf++ = *pbuf_odd;
- }
-}
-
-void ide_output_data(int dev, const ulong *sect_buf, int words)
-{
- uchar *dbuf;
- volatile uchar *pbuf_even;
- volatile uchar *pbuf_odd;
-
- pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
- pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
- dbuf = (uchar *) sect_buf;
- while (words--) {
- EIEIO;
- *pbuf_even = *dbuf++;
- EIEIO;
- *pbuf_odd = *dbuf++;
- EIEIO;
- *pbuf_even = *dbuf++;
- EIEIO;
- *pbuf_odd = *dbuf++;
- }
-}
-
-void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts)
-{
- uchar *dbuf;
- volatile uchar *pbuf_even;
- volatile uchar *pbuf_odd;
-
- pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
- pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
- dbuf = (uchar *) sect_buf;
- while (shorts--) {
- EIEIO;
- *pbuf_even = *dbuf++;
- EIEIO;
- *pbuf_odd = *dbuf++;
- }
-}
-
-void ide_led(uchar led, uchar status)
-{
- u_char val;
- /* We have one PCMCIA slot and use LED H4 for the IDE Interface */
- val = readb(BCSR_BASE + 0x04);
- if (status) /* led on */
- val |= B_CTRL_LED0;
- else
- val &= ~B_CTRL_LED0;
-
- writeb(val, BCSR_BASE + 0x04);
-}
diff --git a/board/cpc45/pd67290.c b/board/cpc45/pd67290.c
deleted file mode 100644
index 23d87f6..0000000
--- a/board/cpc45/pd67290.c
+++ /dev/null
@@ -1,797 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- ********************************************************************
- *
- * Lots of code copied from:
- *
- * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
- * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
- * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
- */
-
-#include <common.h>
-
-#ifdef CONFIG_I82365
-
-#include <command.h>
-#include <pci.h>
-#include <pcmcia.h>
-#include <asm/io.h>
-
-#include <pcmcia/ss.h>
-#include <pcmcia/i82365.h>
-#include <pcmcia/yenta.h>
-#include <pcmcia/cirrus.h>
-
-static struct pci_device_id supported[] = {
- {PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6729},
- {0, 0}
-};
-
-#define CYCLE_TIME 120
-
-#ifdef DEBUG
-static void i82365_dump_regions (pci_dev_t dev);
-#endif
-
-typedef struct socket_info_t {
- pci_dev_t dev;
- u_short bcr;
- u_char pci_lat, cb_lat, sub_bus, cache;
- u_int cb_phys;
-
- socket_cap_t cap;
- u_short type;
- u_int flags;
- cirrus_state_t c_state;
-} socket_info_t;
-
-/* These definitions must match the pcic table! */
-typedef enum pcic_id {
- IS_PD6710, IS_PD672X, IS_VT83C469
-} pcic_id;
-
-typedef struct pcic_t {
- char *name;
-} pcic_t;
-
-static pcic_t pcic[] = {
- {" Cirrus PD6710: "},
- {" Cirrus PD672x: "},
- {" VIA VT83C469: "},
-};
-
-static socket_info_t socket;
-static socket_state_t state;
-static struct pccard_mem_map mem;
-static struct pccard_io_map io;
-
-/*====================================================================*/
-
-/* Some PCI shortcuts */
-
-static int pci_readb (socket_info_t * s, int r, u_char * v)
-{
- return pci_read_config_byte (s->dev, r, v);
-}
-static int pci_writeb (socket_info_t * s, int r, u_char v)
-{
- return pci_write_config_byte (s->dev, r, v);
-}
-static int pci_readw (socket_info_t * s, int r, u_short * v)
-{
- return pci_read_config_word (s->dev, r, v);
-}
-static int pci_writew (socket_info_t * s, int r, u_short v)
-{
- return pci_write_config_word (s->dev, r, v);
-}
-
-/*====================================================================*/
-
-#define cb_readb(s) readb((s)->cb_phys + 1)
-#define cb_writeb(s, v) writeb(v, (s)->cb_phys)
-#define cb_writeb2(s, v) writeb(v, (s)->cb_phys + 1)
-#define cb_readl(s, r) readl((s)->cb_phys + (r))
-#define cb_writel(s, r, v) writel(v, (s)->cb_phys + (r))
-
-
-static u_char i365_get (socket_info_t * s, u_short reg)
-{
- u_char val;
-#ifdef CONFIG_PCMCIA_SLOT_A
- int slot = 0;
-#else
- int slot = 1;
-#endif
-
- val = I365_REG (slot, reg);
-
- cb_writeb (s, val);
- val = cb_readb (s);
-
- debug ("i365_get slot:%x reg: %x val: %x\n", slot, reg, val);
- return val;
-}
-
-static void i365_set (socket_info_t * s, u_short reg, u_char data)
-{
-#ifdef CONFIG_PCMCIA_SLOT_A
- int slot = 0;
-#else
- int slot = 1;
-#endif
- u_char val;
-
- val = I365_REG (slot, reg);
-
- cb_writeb (s, val);
- cb_writeb2 (s, data);
-
- debug ("i365_set slot:%x reg: %x data:%x\n", slot, reg, data);
-}
-
-static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
-{
- i365_set (s, reg, i365_get (s, reg) | mask);
-}
-
-static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
-{
- i365_set (s, reg, i365_get (s, reg) & ~mask);
-}
-
-#if 0 /* not used */
-static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
-{
- u_char d = i365_get (s, reg);
-
- i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
-}
-
-static u_short i365_get_pair (socket_info_t * s, u_short reg)
-{
- return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
-}
-#endif /* not used */
-
-static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
-{
- i365_set (s, reg, data & 0xff);
- i365_set (s, reg + 1, data >> 8);
-}
-
-/*======================================================================
-
- Code to save and restore global state information for Cirrus
- PD67xx controllers, and to set and report global configuration
- options.
-
-======================================================================*/
-
-#define flip(v,b,f) (v = ((f)<0) ? v : ((f) ? ((v)|(b)) : ((v)&(~b))))
-
-static void cirrus_get_state (socket_info_t * s)
-{
- int i;
- cirrus_state_t *p = &s->c_state;
-
- p->misc1 = i365_get (s, PD67_MISC_CTL_1);
- p->misc1 &= (PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
- p->misc2 = i365_get (s, PD67_MISC_CTL_2);
- for (i = 0; i < 6; i++)
- p->timer[i] = i365_get (s, PD67_TIME_SETUP (0) + i);
-
-}
-
-static void cirrus_set_state (socket_info_t * s)
-{
- int i;
- u_char misc;
- cirrus_state_t *p = &s->c_state;
-
- misc = i365_get (s, PD67_MISC_CTL_2);
- i365_set (s, PD67_MISC_CTL_2, p->misc2);
- if (misc & PD67_MC2_SUSPEND)
- udelay (50000);
- misc = i365_get (s, PD67_MISC_CTL_1);
- misc &= ~(PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
- i365_set (s, PD67_MISC_CTL_1, misc | p->misc1);
- for (i = 0; i < 6; i++)
- i365_set (s, PD67_TIME_SETUP (0) + i, p->timer[i]);
-}
-
-static u_int cirrus_set_opts (socket_info_t * s)
-{
- cirrus_state_t *p = &s->c_state;
- u_int mask = 0xffff;
- char buf[200] = {0};
-
- if (has_ring == -1)
- has_ring = 1;
- flip (p->misc2, PD67_MC2_IRQ15_RI, has_ring);
- flip (p->misc2, PD67_MC2_DYNAMIC_MODE, dynamic_mode);
-#if DEBUG
- if (p->misc2 & PD67_MC2_IRQ15_RI)
- strcat (buf, " [ring]");
- if (p->misc2 & PD67_MC2_DYNAMIC_MODE)
- strcat (buf, " [dyn mode]");
- if (p->misc1 & PD67_MC1_INPACK_ENA)
- strcat (buf, " [inpack]");
-#endif
-
- if (p->misc2 & PD67_MC2_IRQ15_RI)
- mask &= ~0x8000;
- if (has_led > 0) {
-#if DEBUG
- strcat (buf, " [led]");
-#endif
- mask &= ~0x1000;
- }
- if (has_dma > 0) {
-#if DEBUG
- strcat (buf, " [dma]");
-#endif
- mask &= ~0x0600;
- flip (p->misc2, PD67_MC2_FREQ_BYPASS, freq_bypass);
-#if DEBUG
- if (p->misc2 & PD67_MC2_FREQ_BYPASS)
- strcat (buf, " [freq bypass]");
-#endif
- }
-
- if (setup_time >= 0)
- p->timer[0] = p->timer[3] = setup_time;
- if (cmd_time > 0) {
- p->timer[1] = cmd_time;
- p->timer[4] = cmd_time * 2 + 4;
- }
- if (p->timer[1] == 0) {
- p->timer[1] = 6;
- p->timer[4] = 16;
- if (p->timer[0] == 0)
- p->timer[0] = p->timer[3] = 1;
- }
- if (recov_time >= 0)
- p->timer[2] = p->timer[5] = recov_time;
-
- debug ("i82365 Opt: %s [%d/%d/%d] [%d/%d/%d]\n",
- buf,
- p->timer[0], p->timer[1], p->timer[2],
- p->timer[3], p->timer[4], p->timer[5]);
-
- return mask;
-}
-
-/*======================================================================
-
- Routines to handle common CardBus options
-
-======================================================================*/
-
-/* Default settings for PCI command configuration register */
-#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
- PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
-
-static void cb_get_state (socket_info_t * s)
-{
- pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
- pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
- pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
- pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
- pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
- pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
-}
-
-static void cb_set_state (socket_info_t * s)
-{
- pci_writew (s, PCI_COMMAND, CMD_DFLT);
- pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
- pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
- pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
- pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
- pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
- pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
-}
-
-static void cb_set_opts (socket_info_t * s)
-{
-}
-
-/*======================================================================
-
- Power control for Cardbus controllers: used both for 16-bit and
- Cardbus cards.
-
-======================================================================*/
-
-static int cb_set_power (socket_info_t * s, socket_state_t * state)
-{
- u_int reg = 0;
-
- reg = I365_PWR_NORESET;
- if (state->flags & SS_PWR_AUTO)
- reg |= I365_PWR_AUTO;
- if (state->flags & SS_OUTPUT_ENA)
- reg |= I365_PWR_OUT;
- if (state->Vpp != 0) {
- if (state->Vpp == 120) {
- reg |= I365_VPP1_12V;
- puts (" 12V card found: ");
- } else if (state->Vpp == state->Vcc) {
- reg |= I365_VPP1_5V;
- } else {
- puts (" power not found: ");
- return -1;
- }
- }
- if (state->Vcc != 0) {
- reg |= I365_VCC_5V;
- if (state->Vcc == 33) {
- puts (" 3.3V card found: ");
- i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- } else if (state->Vcc == 50) {
- puts (" 5V card found: ");
- i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- } else {
- puts (" power not found: ");
- return -1;
- }
- }
-
- if (reg != i365_get (s, I365_POWER)) {
- reg = (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V);
- i365_set (s, I365_POWER, reg);
- }
-
- return 0;
-}
-
-/*======================================================================
-
- Generic routines to get and set controller options
-
-======================================================================*/
-
-static void get_bridge_state (socket_info_t * s)
-{
- cirrus_get_state (s);
- cb_get_state (s);
-}
-
-static void set_bridge_state (socket_info_t * s)
-{
- cb_set_state (s);
- i365_set (s, I365_GBLCTL, 0x00);
- i365_set (s, I365_GENCTL, 0x00);
- cirrus_set_state (s);
-}
-
-static void set_bridge_opts (socket_info_t * s)
-{
- cirrus_set_opts (s);
- cb_set_opts (s);
-}
-
-/*====================================================================*/
-#define PD67_EXT_INDEX 0x2e /* Extension index */
-#define PD67_EXT_DATA 0x2f /* Extension data */
-#define PD67_EXD_VS1(s) (0x01 << ((s)<<1))
-
-#define pd67_ext_get(s, r) \
- (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
-
-static int i365_get_status (socket_info_t * s, u_int * value)
-{
- u_int status;
- u_char val;
- u_char power, vcc, vpp;
- u_int powerstate;
-
- status = i365_get (s, I365_IDENT);
- status = i365_get (s, I365_STATUS);
- *value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
- if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
- *value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
- } else {
- *value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
- *value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
- }
- *value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
- *value |= (status & I365_CS_READY) ? SS_READY : 0;
- *value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
-
- /* Check for Cirrus CL-PD67xx chips */
- i365_set (s, PD67_CHIP_INFO, 0);
- val = i365_get (s, PD67_CHIP_INFO);
- s->type = -1;
- if ((val & PD67_INFO_CHIP_ID) == PD67_INFO_CHIP_ID) {
- val = i365_get (s, PD67_CHIP_INFO);
- if ((val & PD67_INFO_CHIP_ID) == 0) {
- s->type = (val & PD67_INFO_SLOTS) ? IS_PD672X : IS_PD6710;
- i365_set (s, PD67_EXT_INDEX, 0xe5);
- if (i365_get (s, PD67_EXT_INDEX) != 0xe5)
- s->type = IS_VT83C469;
- }
- } else {
- printf ("no Cirrus Chip found\n");
- *value = 0;
- return -1;
- }
-
- power = i365_get (s, I365_POWER);
- state.flags |= (power & I365_PWR_AUTO) ? SS_PWR_AUTO : 0;
- state.flags |= (power & I365_PWR_OUT) ? SS_OUTPUT_ENA : 0;
- vcc = power & I365_VCC_MASK;
- vpp = power & I365_VPP1_MASK;
- state.Vcc = state.Vpp = 0;
- if((vcc== 0) || (vpp == 0)) {
- /*
- * On the Cirrus we get the info which card voltage
- * we have in EXTERN DATA and write it to MISC_CTL1
- */
- powerstate = pd67_ext_get(s, PD67_EXTERN_DATA);
- if (powerstate & PD67_EXD_VS1(0)) {
- /* 5V Card */
- i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- } else {
- /* 3.3V Card */
- i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- }
- i365_set (s, I365_POWER, (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V));
- power = i365_get (s, I365_POWER);
- }
- if (power & I365_VCC_5V) {
- state.Vcc = (i365_get(s, PD67_MISC_CTL_1) & PD67_MC1_VCC_3V) ? 33 : 50;
- }
-
- if (power == I365_VPP1_12V)
- state.Vpp = 120;
-
- /* IO card, RESET flags, IO interrupt */
- power = i365_get (s, I365_INTCTL);
- state.flags |= (power & I365_PC_RESET) ? 0 : SS_RESET;
- if (power & I365_PC_IOCARD)
- state.flags |= SS_IOCARD;
- state.io_irq = power & I365_IRQ_MASK;
-
- /* Card status change mask */
- power = i365_get (s, I365_CSCINT);
- state.csc_mask = (power & I365_CSC_DETECT) ? SS_DETECT : 0;
- if (state.flags & SS_IOCARD)
- state.csc_mask |= (power & I365_CSC_STSCHG) ? SS_STSCHG : 0;
- else {
- state.csc_mask |= (power & I365_CSC_BVD1) ? SS_BATDEAD : 0;
- state.csc_mask |= (power & I365_CSC_BVD2) ? SS_BATWARN : 0;
- state.csc_mask |= (power & I365_CSC_READY) ? SS_READY : 0;
- }
- debug ("i82365: GetStatus(0) = flags %#3.3x, Vcc %d, Vpp %d, "
- "io_irq %d, csc_mask %#2.2x\n", state.flags,
- state.Vcc, state.Vpp, state.io_irq, state.csc_mask);
-
- return 0;
-} /* i365_get_status */
-
-static int i365_set_socket (socket_info_t * s, socket_state_t * state)
-{
- u_char reg;
-
- set_bridge_state (s);
-
- /* IO card, RESET flag */
- reg = 0;
- reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
- reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
- i365_set (s, I365_INTCTL, reg);
-
- cb_set_power (s, state);
-
-#if 0
- /* Card status change interrupt mask */
- reg = s->cs_irq << 4;
- if (state->csc_mask & SS_DETECT)
- reg |= I365_CSC_DETECT;
- if (state->flags & SS_IOCARD) {
- if (state->csc_mask & SS_STSCHG)
- reg |= I365_CSC_STSCHG;
- } else {
- if (state->csc_mask & SS_BATDEAD)
- reg |= I365_CSC_BVD1;
- if (state->csc_mask & SS_BATWARN)
- reg |= I365_CSC_BVD2;
- if (state->csc_mask & SS_READY)
- reg |= I365_CSC_READY;
- }
- i365_set (s, I365_CSCINT, reg);
- i365_get (s, I365_CSC);
-#endif /* 0 */
-
- return 0;
-} /* i365_set_socket */
-
-/*====================================================================*/
-
-static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
-{
- u_short base, i;
- u_char map;
-
- debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
- mem->map, mem->flags, mem->speed,
- mem->sys_start, mem->sys_stop, mem->card_start);
-
- map = mem->map;
- if ((map > 4) ||
- (mem->card_start > 0x3ffffff) ||
- (mem->sys_start > mem->sys_stop) ||
- (mem->speed > 1000)) {
- return -1;
- }
-
- /* Turn off the window before changing anything */
- if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
- i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
-
- /* Take care of high byte, for PCI controllers */
- i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
-
- base = I365_MEM (map);
- i = (mem->sys_start >> 12) & 0x0fff;
- if (mem->flags & MAP_16BIT)
- i |= I365_MEM_16BIT;
- if (mem->flags & MAP_0WS)
- i |= I365_MEM_0WS;
- i365_set_pair (s, base + I365_W_START, i);
-
- i = (mem->sys_stop >> 12) & 0x0fff;
- switch (mem->speed / CYCLE_TIME) {
- case 0:
- break;
- case 1:
- i |= I365_MEM_WS0;
- break;
- case 2:
- i |= I365_MEM_WS1;
- break;
- default:
- i |= I365_MEM_WS1 | I365_MEM_WS0;
- break;
- }
- i365_set_pair (s, base + I365_W_STOP, i);
-
- i = 0;
- if (mem->flags & MAP_WRPROT)
- i |= I365_MEM_WRPROT;
- if (mem->flags & MAP_ATTRIB)
- i |= I365_MEM_REG;
- i365_set_pair (s, base + I365_W_OFF, i);
-
- /* set System Memory map Upper Adress */
- i365_set(s, PD67_EXT_INDEX, PD67_MEM_PAGE(map));
- i365_set(s, PD67_EXT_DATA, ((mem->sys_start >> 24) & 0xff));
-
- /* Turn on the window if necessary */
- if (mem->flags & MAP_ACTIVE)
- i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
- return 0;
-} /* i365_set_mem_map */
-
-static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
-{
- u_char map, ioctl;
-
- map = io->map;
- /* comment out: comparison is always false due to limited range of data type */
- if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
- (io->stop < io->start))
- return -1;
- /* Turn off the window before changing anything */
- if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
- i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
- i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
- i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
- ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
- if (io->speed)
- ioctl |= I365_IOCTL_WAIT (map);
- if (io->flags & MAP_0WS)
- ioctl |= I365_IOCTL_0WS (map);
- if (io->flags & MAP_16BIT)
- ioctl |= I365_IOCTL_16BIT (map);
- if (io->flags & MAP_AUTOSZ)
- ioctl |= I365_IOCTL_IOCS16 (map);
- i365_set (s, I365_IOCTL, ioctl);
- /* Turn on the window if necessary */
- if (io->flags & MAP_ACTIVE)
- i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
- return 0;
-} /* i365_set_io_map */
-
-/*====================================================================*/
-
-/*
- * PCI_ADDR = (HOST_ADDR - 0xfe000000)
- * see MPC 8245 Users Manual Adress Map B
- */
-#define HOST_TO_PCI(addr) ((addr) - 0xfe000000)
-#define PCI_TO_HOST(addr) ((addr) + 0xfe000000)
-
-static int i82365_init (void)
-{
- u_int val;
- int i;
-
- if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
- /* Controller not found */
- printf ("No PD67290 device found !!\n");
- return 1;
- }
- debug ("i82365 Device Found!\n");
-
- socket.cb_phys = PCMCIA_IO_BASE;
-
- /* set base address */
- pci_write_config_dword (socket.dev, PCI_BASE_ADDRESS_0,
- HOST_TO_PCI(socket.cb_phys));
-
- /* enable mapped memory and IO addresses */
- pci_write_config_dword (socket.dev,
- PCI_COMMAND,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_IO | PCI_COMMAND_WAIT);
-
- get_bridge_state (&socket);
- set_bridge_opts (&socket);
-
- i = i365_get_status (&socket, &val);
-
- if (i > -1) {
- puts (pcic[socket.type].name);
- } else {
- printf ("i82365: Controller not found.\n");
- return 1;
- }
- if((val & SS_DETECT) != SS_DETECT){
- puts ("No card\n");
- return 1;
- }
-
- state.flags |= SS_OUTPUT_ENA;
-
- i365_set_socket (&socket, &state);
-
- for (i = 500; i; i--) {
- if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
- break;
- udelay (1000);
- }
-
- if (i == 0) {
- /* PC Card not ready for data transfer */
- puts ("i82365 PC Card not ready for data transfer\n");
- return 1;
- }
- debug (" PC Card ready for data transfer: ");
-
- mem.map = 0;
- mem.flags = MAP_ATTRIB | MAP_ACTIVE;
- mem.speed = 300;
- mem.sys_start = CONFIG_SYS_PCMCIA_MEM_ADDR;
- mem.sys_stop = CONFIG_SYS_PCMCIA_MEM_ADDR + CONFIG_SYS_PCMCIA_MEM_SIZE - 1;
- mem.card_start = 0;
- i365_set_mem_map (&socket, &mem);
-
- mem.map = 1;
- mem.flags = MAP_ACTIVE;
- mem.speed = 300;
- mem.sys_start = CONFIG_SYS_PCMCIA_MEM_ADDR + CONFIG_SYS_PCMCIA_MEM_SIZE;
- mem.sys_stop = CONFIG_SYS_PCMCIA_MEM_ADDR + (2 * CONFIG_SYS_PCMCIA_MEM_SIZE) - 1;
- mem.card_start = 0;
- i365_set_mem_map (&socket, &mem);
-
-#ifdef DEBUG
- i82365_dump_regions (socket.dev);
-#endif
-
- return 0;
-}
-
-static void i82365_exit (void)
-{
- io.map = 0;
- io.flags = 0;
- io.speed = 0;
- io.start = 0;
- io.stop = 0x1;
-
- i365_set_io_map (&socket, &io);
-
- mem.map = 0;
- mem.flags = 0;
- mem.speed = 0;
- mem.sys_start = 0;
- mem.sys_stop = 0x1000;
- mem.card_start = 0;
-
- i365_set_mem_map (&socket, &mem);
-
- mem.map = 1;
- mem.flags = 0;
- mem.speed = 0;
- mem.sys_start = 0;
- mem.sys_stop = 0x1000;
- mem.card_start = 0;
-
- i365_set_mem_map (&socket, &mem);
-
- state.Vcc = state.Vpp = 0;
-
- i365_set_socket (&socket, &state);
-}
-
-int pcmcia_on (void)
-{
- u_int rc;
-
- debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- rc = i82365_init();
- if (rc)
- goto exit;
-
- rc = check_ide_device(0);
- if (rc == 0)
- goto exit;
-
- i82365_exit();
-
-exit:
- return rc;
-}
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_off (void)
-{
- printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- i82365_exit();
-
- return 0;
-}
-#endif
-
-/*======================================================================
-
- Debug stuff
-
-======================================================================*/
-
-#ifdef DEBUG
-static void i82365_dump_regions (pci_dev_t dev)
-{
- u_int tmp[2];
- u_int *mem = (void *) socket.cb_phys;
- u_char *cis = (void *) CONFIG_SYS_PCMCIA_MEM_ADDR;
- u_char *ide = (void *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_REG_OFFSET);
-
- pci_read_config_dword (dev, 0x00, tmp + 0);
- pci_read_config_dword (dev, 0x80, tmp + 1);
-
- printf ("PCI CONF: %08X ... %08X\n",
- tmp[0], tmp[1]);
- printf ("PCI MEM: ... %08X ... %08X\n",
- mem[0x8 / 4], mem[0x800 / 4]);
- printf ("CIS: ...%c%c%c%c%c%c%c%c...\n",
- cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
- cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
- printf ("CIS CONF: %02X %02X %02X ...\n",
- cis[0x200], cis[0x202], cis[0x204]);
- printf ("IDE: %02X %02X %02X %02X %02X %02X %02X %02X\n",
- ide[0], ide[1], ide[2], ide[3],
- ide[4], ide[5], ide[6], ide[7]);
-}
-#endif /* DEBUG */
-
-#endif /* CONFIG_I82365 */
diff --git a/board/cpc45/plx9030.c b/board/cpc45/plx9030.c
deleted file mode 100644
index 06fb8d6..0000000
--- a/board/cpc45/plx9030.c
+++ /dev/null
@@ -1,156 +0,0 @@
-/* Plx9030.c - system configuration module for PLX9030 PCI to Local Bus Bridge */
-/*
- * (C) Copyright 2002-2003
- * Josef Wagner, MicroSys GmbH, wagner at microsys.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- * Date Modification by
- * ------- ---------------------------------------------- ---
- * 30sep02 converted from VxWorks to LINUX wa
-*/
-
-
-/*
-DESCRIPTION
-
-This is the configuration module for the PLX9030 PCI to Local Bus Bridge.
-It configures the Chip select lines for SRAM (CS0), ST16C552 (CS1,CS2), Display and local
-registers (CS3) on CPC45.
-*/
-
-/* includes */
-
-#include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/io.h>
-#include <pci.h>
-
-/* imports */
-
-
-/* defines */
-#define PLX9030_VENDOR_ID 0x10B5
-#define PLX9030_DEVICE_ID 0x9030
-
-#undef PLX_DEBUG
-
-/* PLX9030 register offsets */
-#define P9030_LAS0RR 0x00
-#define P9030_LAS1RR 0x04
-#define P9030_LAS2RR 0x08
-#define P9030_LAS3RR 0x0c
-#define P9030_EROMRR 0x10
-#define P9030_LAS0BA 0x14
-#define P9030_LAS1BA 0x18
-#define P9030_LAS2BA 0x1c
-#define P9030_LAS3BA 0x20
-#define P9030_EROMBA 0x24
-#define P9030_LAS0BRD 0x28
-#define P9030_LAS1BRD 0x2c
-#define P9030_LAS2BRD 0x30
-#define P9030_LAS3BRD 0x34
-#define P9030_EROMBRD 0x38
-#define P9030_CS0BASE 0x3C
-#define P9030_CS1BASE 0x40
-#define P9030_CS2BASE 0x44
-#define P9030_CS3BASE 0x48
-#define P9030_INTCSR 0x4c
-#define P9030_CNTRL 0x50
-#define P9030_GPIOC 0x54
-
-/* typedefs */
-
-
-/* locals */
-
-static struct pci_device_id supported[] = {
- { PLX9030_VENDOR_ID, PLX9030_DEVICE_ID },
- { }
-};
-
-/* forward declarations */
-void sysOutLong(ulong address, ulong value);
-
-
-/***************************************************************************
-*
-* Plx9030Init - init CS0..CS3 for CPC45
-*
-*
-* RETURNS: N/A
-*/
-
-void Plx9030Init (void)
-{
- pci_dev_t devno;
- ulong membaseCsr; /* base address of device memory space */
- int idx = 0; /* general index */
-
-
- /* find plx9030 device */
-
- if ((devno = pci_find_devices(supported, idx++)) < 0)
- {
- printf("No PLX9030 device found !!\n");
- return;
- }
-
-
-#ifdef PLX_DEBUG
- printf("PLX 9030 device found ! devno = 0x%x\n",devno);
-#endif
-
- membaseCsr = PCI_PLX9030_MEMADDR;
-
- /* set base address */
- pci_write_config_dword(devno, PCI_BASE_ADDRESS_0, membaseCsr);
-
- /* enable mapped memory and IO addresses */
- pci_write_config_dword(devno,
- PCI_COMMAND,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER);
-
-
- /* configure GBIOC */
- sysOutLong((membaseCsr + P9030_GPIOC), 0x00000FC0); /* CS2/CS3 enable */
-
- /* configure CS0 (SRAM) */
- sysOutLong((membaseCsr + P9030_LAS0BA), 0x00000001); /* enable space base */
- sysOutLong((membaseCsr + P9030_LAS0RR), 0x0FE00000); /* 2 MByte */
- sysOutLong((membaseCsr + P9030_LAS0BRD), 0x51928900); /* 4 wait states */
- sysOutLong((membaseCsr + P9030_CS0BASE), 0x00100001); /* enable 2 MByte */
- /* remap CS0 (SRAM) */
- pci_write_config_dword(devno, PCI_BASE_ADDRESS_2, SRAM_BASE);
-
- /* configure CS1 (ST16552 / CHAN A) */
- sysOutLong((membaseCsr + P9030_LAS1BA), 0x00400001); /* enable space base */
- sysOutLong((membaseCsr + P9030_LAS1RR), 0x0FFFFF00); /* 256 byte */
- sysOutLong((membaseCsr + P9030_LAS1BRD), 0x55122900); /* 4 wait states */
- sysOutLong((membaseCsr + P9030_CS1BASE), 0x00400081); /* enable 256 Byte */
- /* remap CS1 (ST16552 / CHAN A) */
- /* remap CS1 (ST16552 / CHAN A) */
- pci_write_config_dword(devno, PCI_BASE_ADDRESS_3, ST16552_A_BASE);
-
- /* configure CS2 (ST16552 / CHAN B) */
- sysOutLong((membaseCsr + P9030_LAS2BA), 0x00800001); /* enable space base */
- sysOutLong((membaseCsr + P9030_LAS2RR), 0x0FFFFF00); /* 256 byte */
- sysOutLong((membaseCsr + P9030_LAS2BRD), 0x55122900); /* 4 wait states */
- sysOutLong((membaseCsr + P9030_CS2BASE), 0x00800081); /* enable 256 Byte */
- /* remap CS2 (ST16552 / CHAN B) */
- pci_write_config_dword(devno, PCI_BASE_ADDRESS_4, ST16552_B_BASE);
-
- /* configure CS3 (BCSR) */
- sysOutLong((membaseCsr + P9030_LAS3BA), 0x00C00001); /* enable space base */
- sysOutLong((membaseCsr + P9030_LAS3RR), 0x0FFFFF00); /* 256 byte */
- sysOutLong((membaseCsr + P9030_LAS3BRD), 0x55357A80); /* 9 wait states */
- sysOutLong((membaseCsr + P9030_CS3BASE), 0x00C00081); /* enable 256 Byte */
- /* remap CS3 (DISPLAY and BCSR) */
- pci_write_config_dword(devno, PCI_BASE_ADDRESS_5, BCSR_BASE);
-}
-
-void sysOutLong(ulong address, ulong value)
-{
- *(ulong*)address = cpu_to_le32(value);
-}
diff --git a/board/cu824/Kconfig b/board/cu824/Kconfig
deleted file mode 100644
index 7927b05..0000000
--- a/board/cu824/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_CU824
-
-config SYS_BOARD
- default "cu824"
-
-config SYS_CONFIG_NAME
- default "CU824"
-
-endif
diff --git a/board/cu824/MAINTAINERS b/board/cu824/MAINTAINERS
deleted file mode 100644
index b1b7190..0000000
--- a/board/cu824/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-CU824 BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/cu824/
-F: include/configs/CU824.h
-F: configs/CU824_defconfig
diff --git a/board/cu824/Makefile b/board/cu824/Makefile
deleted file mode 100644
index e7bd7ca..0000000
--- a/board/cu824/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = cu824.o flash.o
diff --git a/board/cu824/README b/board/cu824/README
deleted file mode 100644
index cc0d207..0000000
--- a/board/cu824/README
+++ /dev/null
@@ -1,453 +0,0 @@
-ppcboot for a CU824 board
----------------------------
-
-CU824 has two banks of flash 8MB each. In board's notation, bank 0 is
-the one at the address of 0xFF800000 and bank 1 is the one at the
-address of 0xFF000000. On power-up the processor jumps to the address
-of 0xFFF00100, the last megabyte of the bank 0 of flash. Thus,
-U-Boot is configured to reside in flash starting at the address of
-0xFFF00000. The environment space is not embedded in the U-Boot code
-and is located in flash separately from U-Boot, at the address of
-0xFF008000.
-
-
-U-Boot test results
---------------------
-
-x.x Operation on all available serial consoles
-
-x.x.x CONFIG_CONS_INDEX 1
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>he
-go - start application at address 'addr'
-run - run commands in an environment variable
-bootm - boot application image from memory
-bootp - boot image via network using BootP/TFTP protocol
-tftpboot- boot image via network using TFTP protocol
- and env variables ipaddr and serverip
-rarpboot- boot image via network using RARP/TFTP protocol
-bootd - boot default, i.e., run 'bootcmd'
-loads - load S-Record file over serial line
-loadb - load binary file over serial line (kermit mode)
-md - memory display
-mm - memory modify (auto-incrementing)
-nm - memory modify (constant address)
-mw - memory write (fill)
-cp - memory copy
-cmp - memory compare
-crc32 - checksum calculation
-base - print or set address offset
-printenv- print environment variables
-setenv - set environment variables
-saveenv - save environment variables to persistent storage
-protect - enable or disable FLASH write protection
-erase - erase FLASH memory
-flinfo - print FLASH memory information
-bdinfo - print Board Info structure
-iminfo - print header information for application image
-coninfo - print console devices and informations
-loop - infinite loop on address range
-mtest - simple RAM test
-icache - enable or disable instruction cache
-dcache - enable or disable data cache
-reset - Perform RESET of the CPU
-echo - echo args to console
-version - print monitor version
-help - print online help
-? - alias for 'help'
-=>
-
-
-x.x.x CONFIG_CONS_INDEX 2
-
-**** NOT TESTED ****
-
-x.x Flash Driver Operation
-
-x.x.x Erase Operation
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>
-=>
-=>md ff000000
-ff000000: 27051956 70706362 6f6f7420 302e382e '..Vppcboot 0.8.
-ff000010: 3320284d 61792031 31203230 3031202d 3 (May 11 2001 -
-ff000020: 2031343a 35373a30 33290000 00000000 14:57:03)......
-ff000030: 00000000 00000000 00000000 00000000 ................
-ff000040: 00000000 00000000 00000000 00000000 ................
-ff000050: 00000000 00000000 00000000 00000000 ................
-ff000060: 00000000 00000000 00000000 00000000 ................
-ff000070: 00000000 00000000 00000000 00000000 ................
-ff000080: 00000000 00000000 00000000 00000000 ................
-ff000090: 00000000 00000000 00000000 00000000 ................
-ff0000a0: 00000000 00000000 00000000 00000000 ................
-ff0000b0: 00000000 00000000 00000000 00000000 ................
-ff0000c0: 00000000 00000000 00000000 00000000 ................
-ff0000d0: 00000000 00000000 00000000 00000000 ................
-ff0000e0: 00000000 00000000 00000000 00000000 ................
-ff0000f0: 00000000 00000000 00000000 00000000 ................
-=>erase ff000000 ff007fff
-Erase Flash from 0xff000000 to 0xff007fff
- done
-Erased 1 sectors
-=>md ff000000
-ff000000: ffffffff ffffffff ffffffff ffffffff ................
-ff000010: ffffffff ffffffff ffffffff ffffffff ................
-ff000020: ffffffff ffffffff ffffffff ffffffff ................
-ff000030: ffffffff ffffffff ffffffff ffffffff ................
-ff000040: ffffffff ffffffff ffffffff ffffffff ................
-ff000050: ffffffff ffffffff ffffffff ffffffff ................
-ff000060: ffffffff ffffffff ffffffff ffffffff ................
-ff000070: ffffffff ffffffff ffffffff ffffffff ................
-ff000080: ffffffff ffffffff ffffffff ffffffff ................
-ff000090: ffffffff ffffffff ffffffff ffffffff ................
-ff0000a0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000b0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000c0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000d0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000e0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000f0: ffffffff ffffffff ffffffff ffffffff ................
-=>
-
-x.x.x Information
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>
-=>
-=>
-=>flinfo
-
-Bank # 1: Intel: 28F160F3B (16Mbit)
- Size: 8 MB in 39 Sectors
- Sector Start Addresses:
- FF000000 FF008000 (RO) FF010000 FF018000 FF020000
- FF028000 FF030000 FF038000 FF040000 FF080000
- FF0C0000 FF100000 FF140000 FF180000 FF1C0000
- FF200000 FF240000 FF280000 FF2C0000 FF300000
- FF340000 FF380000 FF3C0000 FF400000 FF440000
- FF480000 FF4C0000 FF500000 FF540000 FF580000
- FF5C0000 FF600000 FF640000 FF680000 FF6C0000
- FF700000 FF740000 FF780000 FF7C0000
-
-Bank # 2: Intel: 28F160F3B (16Mbit)
- Size: 8 MB in 39 Sectors
- Sector Start Addresses:
- FF800000 FF808000 FF810000 FF818000 FF820000
- FF828000 FF830000 FF838000 FF840000 FF880000
- FF8C0000 FF900000 FF940000 FF980000 FF9C0000
- FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000
- FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000
- FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000
- FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000
- FFF00000 (RO) FFF40000 FFF80000 FFFC0000
-=>
-
-x.x.x Flash Programming
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>
-=>
-=>
-=>cp 0 ff000000 20
-Copy to Flash... done
-=>md 0
-00000000: 0ec08ce0 03f9800c 00000001 040c0000 ................
-00000010: 00000001 03fd1aa0 03fd1ae4 03fd1a00 ................
-00000020: 03fd1a58 03fceb04 03fd34cc 03fd34d0 ...X......4...4.
-00000030: 03fcd5bc 03fcdabc 00000000 00000000 ................
-00000040: 00000000 00000000 00000000 00000000 ................
-00000050: 00000000 00000000 00000000 00000000 ................
-00000060: 00000000 00000000 00000000 00000000 ................
-00000070: 00000000 00000000 00000000 00000000 ................
-00000080: 00000000 00000000 00000000 00000000 ................
-00000090: 00000000 00000000 00000000 00000000 ................
-000000a0: 00000000 00000000 00000000 00000000 ................
-000000b0: 00000000 00000000 00000000 00000000 ................
-000000c0: 00000000 00000000 00000000 00000000 ................
-000000d0: 00000000 00000000 00000000 00000000 ................
-000000e0: 00000000 00000000 00000000 00000000 ................
-000000f0: 00000000 00000000 00000000 00000000 ................
-=>md ff000000
-ff000000: 0ec08ce0 03f9800c 00000001 040c0000 ................
-ff000010: 00000001 03fd1aa0 03fd1ae4 03fd1a00 ................
-ff000020: 03fd1a58 03fceb04 03fd34cc 03fd34d0 ...X......4...4.
-ff000030: 03fcd5bc 03fcdabc 00000000 00000000 ................
-ff000040: 00000000 00000000 00000000 00000000 ................
-ff000050: 00000000 00000000 00000000 00000000 ................
-ff000060: 00000000 00000000 00000000 00000000 ................
-ff000070: 00000000 00000000 00000000 00000000 ................
-ff000080: ffffffff ffffffff ffffffff ffffffff ................
-ff000090: ffffffff ffffffff ffffffff ffffffff ................
-ff0000a0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000b0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000c0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000d0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000e0: ffffffff ffffffff ffffffff ffffffff ................
-ff0000f0: ffffffff ffffffff ffffffff ffffffff ................
-=>
-
-x.x.x Storage of environment variables in flash
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>printenv
-bootargs=
-bootcmd=bootm FE020000
-bootdelay=5
-baudrate=9600
-ipaddr=192.168.4.2
-serverip=192.168.4.1
-ethaddr=00:40:42:01:00:a0
-stdin=serial
-stdout=serial
-stderr=serial
-
-Environment size: 167/32764 bytes
-=>setenv myvar 1234
-=>save_env
-Un-Protected 1 sectors
-Erasing Flash...
- done
-Erased 1 sectors
-Saving Environment to Flash...
-Protected 1 sectors
-=>reset
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>printenv
-bootargs=
-bootcmd=bootm FE020000
-bootdelay=5
-baudrate=9600
-ipaddr=192.168.4.2
-serverip=192.168.4.1
-ethaddr=00:40:42:01:00:a0
-myvar=1234
-stdin=serial
-stdout=serial
-stderr=serial
-
-Environment size: 178/32764 bytes
-=>
-
-x.x Image Download and run over serial port
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>
-=>mw 40000 0 10000
-=>md 40000
-00040000: 00000000 00000000 00000000 00000000 ................
-00040010: 00000000 00000000 00000000 00000000 ................
-00040020: 00000000 00000000 00000000 00000000 ................
-00040030: 00000000 00000000 00000000 00000000 ................
-00040040: 00000000 00000000 00000000 00000000 ................
-00040050: 00000000 00000000 00000000 00000000 ................
-00040060: 00000000 00000000 00000000 00000000 ................
-00040070: 00000000 00000000 00000000 00000000 ................
-00040080: 00000000 00000000 00000000 00000000 ................
-00040090: 00000000 00000000 00000000 00000000 ................
-000400a0: 00000000 00000000 00000000 00000000 ................
-000400b0: 00000000 00000000 00000000 00000000 ................
-000400c0: 00000000 00000000 00000000 00000000 ................
-000400d0: 00000000 00000000 00000000 00000000 ................
-000400e0: 00000000 00000000 00000000 00000000 ................
-000400f0: 00000000 00000000 00000000 00000000 ................
-=>loads
-## Ready for S-Record download ...
-
-(Back at xpert.denx.de)
-[vlad at xpert vlad]$ cat hello_world.srec >/dev/ttyS0
-[vlad at xpert vlad]$ kermit -l /dev/ttyS0 -b 9600 -c
-Connecting to /dev/ttyS0, speed 9600.
-The escape character is Ctrl-\ (ASCII 28, FS)
-Type the escape character followed by C to get back,
-or followed by ? to see other options.
-md 40000
-00040000: 00018148 9421ffe0 7c0802a6 bf61000c ...H.!..|....a..
-00040010: 90010024 48000005 7fc802a6 801effe8 ...$H...........
-00040020: 7fc0f214 7c7f1b78 813f0038 7c9c2378 ....|..x.?.8|.#x
-00040030: 807e8000 7cbd2b78 80090010 3b600000 .~..|.+x....;`..
-00040040: 7c0803a6 4e800021 813f0038 7f84e378 |...N..!.?.8...x
-00040050: 807e8004 80090010 7c0803a6 4e800021 .~......|...N..!
-00040060: 7c1be000 4181003c 80bd0000 813f0038 |...A..<.....?.8
-00040070: 3bbd0004 2c050000 40820008 80be8008 ;...,... at .......
-00040080: 80090010 7f64db78 807e800c 3b7b0001 .....d.x.~..;{..
-00040090: 7c0803a6 4e800021 7c1be000 4081ffcc |...N..!|...@...
-000400a0: 813f0038 807e8010 80090010 7c0803a6 .?.8.~......|...
-000400b0: 4e800021 813f0038 80090004 7c0803a6 N..!.?.8....|...
-000400c0: 4e800021 2c030000 4182ffec 813f0038 N..!,...A....?.8
-000400d0: 80090000 7c0803a6 4e800021 813f0038 ....|...N..!.?.8
-000400e0: 807e8014 80090010 7c0803a6 4e800021 .~......|...N..!
-000400f0: 38600000 80010024 7c0803a6 bb61000c 8`.....$|....a..
-=>go 40004
-## Starting application at 0x00040004 ...
-Hello World
-argc = 1
-argv[0] = "40004"
-argv[1] = "<NULL>"
-Hit any key to exit ...
-
-## Application terminated, rc = 0x0
-=>
-
-x.x Image download and run over ethernet interface
-
-
-ppcboot 0.9.2 (May 13 2001 - 17:56:46)
-
-Initializing...
- CPU: MPC8240 Revsion 1.1 at 247 MHz: 16 kB I-Cache 16 kB D-Cache
- Board: CU824 Revision 1 Local Bus at 99 MHz
- DRAM: 64 MB
- FLASH: 16 MB
- In: serial
- Out: serial
- Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-=>
-=>mw 40000 0 10000
-=>md 40000
-00040000: 00000000 00000000 00000000 00000000 ................
-00040010: 00000000 00000000 00000000 00000000 ................
-00040020: 00000000 00000000 00000000 00000000 ................
-00040030: 00000000 00000000 00000000 00000000 ................
-00040040: 00000000 00000000 00000000 00000000 ................
-00040050: 00000000 00000000 00000000 00000000 ................
-00040060: 00000000 00000000 00000000 00000000 ................
-00040070: 00000000 00000000 00000000 00000000 ................
-00040080: 00000000 00000000 00000000 00000000 ................
-00040090: 00000000 00000000 00000000 00000000 ................
-000400a0: 00000000 00000000 00000000 00000000 ................
-000400b0: 00000000 00000000 00000000 00000000 ................
-000400c0: 00000000 00000000 00000000 00000000 ................
-000400d0: 00000000 00000000 00000000 00000000 ................
-000400e0: 00000000 00000000 00000000 00000000 ................
-000400f0: 00000000 00000000 00000000 00000000 ................
-=>tftpboot 40000 hello_world.bin
-ARP broadcast 1
-TFTP from server 192.168.4.1; our IP address is 192.168.4.2
-Filename 'hello_world.bin'.
-Load address: 0x40000
-Loading: #############
-done
-Bytes transferred = 65912 (10178 hex)
-=>md 40000
-00040000: 00018148 9421ffe0 7c0802a6 bf61000c ...H.!..|....a..
-00040010: 90010024 48000005 7fc802a6 801effe8 ...$H...........
-00040020: 7fc0f214 7c7f1b78 813f0038 7c9c2378 ....|..x.?.8|.#x
-00040030: 807e8000 7cbd2b78 80090010 3b600000 .~..|.+x....;`..
-00040040: 7c0803a6 4e800021 813f0038 7f84e378 |...N..!.?.8...x
-00040050: 807e8004 80090010 7c0803a6 4e800021 .~......|...N..!
-00040060: 7c1be000 4181003c 80bd0000 813f0038 |...A..<.....?.8
-00040070: 3bbd0004 2c050000 40820008 80be8008 ;...,... at .......
-00040080: 80090010 7f64db78 807e800c 3b7b0001 .....d.x.~..;{..
-00040090: 7c0803a6 4e800021 7c1be000 4081ffcc |...N..!|...@...
-000400a0: 813f0038 807e8010 80090010 7c0803a6 .?.8.~......|...
-000400b0: 4e800021 813f0038 80090004 7c0803a6 N..!.?.8....|...
-000400c0: 4e800021 2c030000 4182ffec 813f0038 N..!,...A....?.8
-000400d0: 80090000 7c0803a6 4e800021 813f0038 ....|...N..!.?.8
-000400e0: 807e8014 80090010 7c0803a6 4e800021 .~......|...N..!
-000400f0: 38600000 80010024 7c0803a6 bb61000c 8`.....$|....a..
-=>go 40004
-## Starting application at 0x00040004 ...
-Hello World
-argc = 1
-argv[0] = "40004"
-argv[1] = "<NULL>"
-Hit any key to exit ...
-
-## Application terminated, rc = 0x0
-=>
diff --git a/board/cu824/cu824.c b/board/cu824/cu824.c
deleted file mode 100644
index 6b23c53..0000000
--- a/board/cu824/cu824.c
+++ /dev/null
@@ -1,83 +0,0 @@
-/*
- * (C) Copyright 2001
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * (C) Copyright 2001-2006
- * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
-
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <pci.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define BOARD_REV_REG 0xFE80002B
-
-int checkboard (void)
-{
- char revision = *(volatile char *)(BOARD_REV_REG);
- char buf[32];
-
- puts ("Board: CU824 ");
- printf("Revision %d ", revision);
- printf("Local Bus at %s MHz\n", strmhz(buf, gd->bus_clk));
-
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- long size;
- long new_bank0_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-/*
- * Initialize PCI Devices, report devices found.
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_sandpoint_config_table[] = {
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
-
- { }
-};
-#endif
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_sandpoint_config_table,
-#endif
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/board/cu824/flash.c b/board/cu824/flash.c
deleted file mode 100644
index 3a6d954..0000000
--- a/board/cu824/flash.c
+++ /dev/null
@@ -1,470 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-#define FLASH_BANK_SIZE 0x800000
-#define MAIN_SECT_SIZE 0x40000
-#define PARAM_SECT_SIZE 0x8000
-
-#define BOARD_CTRL_REG 0xFE800013
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-static int write_data (flash_info_t *info, ulong dest, ulong *data);
-static void write_via_fpu(vu_long *addr, ulong *data);
-static __inline__ unsigned long get_msr(void);
-static __inline__ void set_msr(unsigned long msr);
-
-/*---------------------------------------------------------------------*/
-#undef DEBUG_FLASH
-
-/*---------------------------------------------------------------------*/
-#ifdef DEBUG_FLASH
-#define DEBUGF(fmt,args...) printf(fmt ,##args)
-#else
-#define DEBUGF(fmt,args...)
-#endif
-/*---------------------------------------------------------------------*/
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init(void)
-{
- int i, j;
- ulong size = 0;
- volatile unsigned char *bcr = (volatile unsigned char *)(BOARD_CTRL_REG);
-
- DEBUGF("Write protect was: 0x%02X\n", *bcr);
- *bcr &= 0x1; /* FWPT must be 0 */
- *bcr |= 0x6; /* FWP0 = FWP1 = 1 */
- DEBUGF("Write protect is: 0x%02X\n", *bcr);
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- vu_long *addr = (vu_long *)(CONFIG_SYS_FLASH_BASE + i * FLASH_BANK_SIZE);
-
- addr[0] = 0x00900090;
-
- DEBUGF ("Flash bank # %d:\n"
- "\tManuf. ID @ 0x%08lX: 0x%08lX\n"
- "\tDevice ID @ 0x%08lX: 0x%08lX\n",
- i,
- (ulong)(&addr[0]), addr[0],
- (ulong)(&addr[2]), addr[2]);
-
- if ((addr[0] == addr[1]) && (addr[0] == INTEL_MANUFACT) &&
- (addr[2] == addr[3]) && (addr[2] == INTEL_ID_28F160F3B))
- {
- flash_info[i].flash_id = (FLASH_MAN_INTEL & FLASH_VENDMASK) |
- (INTEL_ID_28F160F3B & FLASH_TYPEMASK);
- } else {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- addr[0] = 0xFFFFFFFF;
- goto Done;
- }
-
- DEBUGF ("flash_id = 0x%08lX\n", flash_info[i].flash_id);
-
- addr[0] = 0xFFFFFFFF;
-
- flash_info[i].size = FLASH_BANK_SIZE;
- flash_info[i].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- memset(flash_info[i].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
- for (j = 0; j < flash_info[i].sector_count; j++) {
- if (j <= 7) {
- flash_info[i].start[j] = CONFIG_SYS_FLASH_BASE +
- i * FLASH_BANK_SIZE +
- j * PARAM_SECT_SIZE;
- } else {
- flash_info[i].start[j] = CONFIG_SYS_FLASH_BASE +
- i * FLASH_BANK_SIZE +
- (j - 7)*MAIN_SECT_SIZE;
- }
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE + FLASH_BANK_SIZE
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[1]);
-#else
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
-#if CONFIG_ENV_ADDR >= CONFIG_SYS_FLASH_BASE + FLASH_BANK_SIZE
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[1]);
-#else
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[0]);
-#endif
-#endif
-
-Done:
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- switch ((i = info->flash_id & FLASH_VENDMASK)) {
- case (FLASH_MAN_INTEL & FLASH_VENDMASK):
- printf ("Intel: ");
- break;
- default:
- printf ("Unknown Vendor 0x%04x ", i);
- break;
- }
-
- switch ((i = info->flash_id & FLASH_TYPEMASK)) {
- case (INTEL_ID_28F160F3B & FLASH_TYPEMASK):
- printf ("28F160F3B (16Mbit)\n");
- break;
- default:
- printf ("Unknown Chip Type 0x%04x\n", i);
- goto Done;
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; i++) {
- if ((i % 5) == 0) {
- printf ("\n ");
- }
- printf (" %08lX%s", info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
-
-Done:
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- DEBUGF ("Erase flash bank %d sect %d ... %d\n",
- info - &flash_info[0], s_first, s_last);
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) !=
- (FLASH_MAN_INTEL & FLASH_VENDMASK)) {
- printf ("Can erase only Intel flash types - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_long *addr = (vu_long *)(info->start[sect]);
-
- DEBUGF ("Erase sect %d @ 0x%08lX\n",
- sect, (ulong)addr);
-
- /* Disable interrupts which might cause a timeout
- * here.
- */
- flag = disable_interrupts();
-
- addr[0] = 0x00500050; /* clear status register */
- addr[0] = 0x00200020; /* erase setup */
- addr[0] = 0x00D000D0; /* erase confirm */
-
- addr[1] = 0x00500050; /* clear status register */
- addr[1] = 0x00200020; /* erase setup */
- addr[1] = 0x00D000D0; /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((addr[0] & 0x00800080) != 0x00800080) ||
- ((addr[1] & 0x00800080) != 0x00800080) ) {
- if ((now=get_timer(start)) >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- addr[0] = 0x00B000B0; /* suspend erase */
- addr[0] = 0x00FF00FF; /* to read mode */
- return 1;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- addr[0] = 0x00FF00FF;
- }
- }
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-#define FLASH_WIDTH 8 /* flash bus width in bytes */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong wp, cp, msr;
- int l, rc, i;
- ulong data[2];
- ulong *datah = &data[0];
- ulong *datal = &data[1];
-
- DEBUGF ("Flash write_buff: @ 0x%08lx, src 0x%08lx len %ld\n",
- addr, (ulong)src, cnt);
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
- msr = get_msr();
- set_msr(msr | MSR_FP);
-
- wp = (addr & ~(FLASH_WIDTH-1)); /* get lower aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- *datah = *datal = 0;
-
- for (i = 0, cp = wp; i < l; i++, cp++) {
- if (i >= 4) {
- *datah = (*datah << 8) |
- ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datal << 8) | (*(uchar *)cp);
- }
- for (; i < FLASH_WIDTH && cnt > 0; ++i) {
- char tmp;
-
- tmp = *src;
-
- src++;
-
- if (i >= 4) {
- *datah = (*datah << 8) |
- ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datal << 8) | tmp;
-
- --cnt; ++cp;
- }
-
- for (; cnt == 0 && i < FLASH_WIDTH; ++i, ++cp) {
- if (i >= 4) {
- *datah = (*datah << 8) |
- ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datah << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_data(info, wp, data)) != 0) {
- set_msr(msr);
- return (rc);
- }
-
- wp += FLASH_WIDTH;
- }
-
- /*
- * handle FLASH_WIDTH aligned part
- */
- while (cnt >= FLASH_WIDTH) {
- *datah = *(ulong *)src;
- *datal = *(ulong *)(src + 4);
- if ((rc = write_data(info, wp, data)) != 0) {
- set_msr(msr);
- return (rc);
- }
- wp += FLASH_WIDTH;
- cnt -= FLASH_WIDTH;
- src += FLASH_WIDTH;
- }
-
- if (cnt == 0) {
- set_msr(msr);
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- *datah = *datal = 0;
- for (i = 0, cp = wp; i < FLASH_WIDTH && cnt > 0; ++i, ++cp) {
- char tmp;
-
- tmp = *src;
-
- src++;
-
- if (i >= 4) {
- *datah = (*datah << 8) | ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datal << 8) | tmp;
-
- --cnt;
- }
-
- for (; i < FLASH_WIDTH; ++i, ++cp) {
- if (i >= 4) {
- *datah = (*datah << 8) | ((*datal & 0xFF000000) >> 24);
- }
-
- *datal = (*datal << 8) | (*(uchar *)cp);
- }
-
- rc = write_data(info, wp, data);
- set_msr(msr);
-
- return (rc);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t *info, ulong dest, ulong *data)
-{
- vu_long *addr = (vu_long *)dest;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if (((addr[0] & data[0]) != data[0]) ||
- ((addr[1] & data[1]) != data[1]) ) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0] = 0x00400040; /* write setup */
- write_via_fpu(addr, data);
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer (0);
-
- while (((addr[0] & 0x00800080) != 0x00800080) ||
- ((addr[1] & 0x00800080) != 0x00800080) ) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- addr[0] = 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
-
- addr[0] = 0x00FF00FF; /* restore read mode */
-
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void write_via_fpu(vu_long *addr, ulong *data)
-{
- __asm__ __volatile__ ("lfd 1, 0(%0)" : : "r" (data));
- __asm__ __volatile__ ("stfd 1, 0(%0)" : : "r" (addr));
-}
-/*-----------------------------------------------------------------------
- */
-static __inline__ unsigned long get_msr(void)
-{
- unsigned long msr;
-
- __asm__ __volatile__ ("mfmsr %0" : "=r" (msr) :);
- return msr;
-}
-
-static __inline__ void set_msr(unsigned long msr)
-{
- __asm__ __volatile__ ("mtmsr %0" : : "r" (msr));
-}
diff --git a/board/eXalion/Kconfig b/board/eXalion/Kconfig
deleted file mode 100644
index a22f58a..0000000
--- a/board/eXalion/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_EXALION
-
-config SYS_BOARD
- default "eXalion"
-
-config SYS_CONFIG_NAME
- default "eXalion"
-
-endif
diff --git a/board/eXalion/MAINTAINERS b/board/eXalion/MAINTAINERS
deleted file mode 100644
index 0ea74ca..0000000
--- a/board/eXalion/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-EXALION BOARD
-M: Torsten Demke <torsten.demke@fci.com>
-S: Maintained
-F: board/eXalion/
-F: include/configs/eXalion.h
-F: configs/eXalion_defconfig
diff --git a/board/eXalion/Makefile b/board/eXalion/Makefile
deleted file mode 100644
index 9192e28..0000000
--- a/board/eXalion/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = eXalion.o
diff --git a/board/eXalion/eXalion.c b/board/eXalion/eXalion.c
deleted file mode 100644
index 304ff21..0000000
--- a/board/eXalion/eXalion.c
+++ /dev/null
@@ -1,283 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * Torsten Demke, FORCE Computers GmbH. torsten.demke at fci.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <pci.h>
-#include <ide.h>
-#include <netdev.h>
-#include <timestamp.h>
-#include "piix_pci.h"
-#include "eXalion.h"
-
-int checkboard (void)
-{
- ulong busfreq = get_bus_freq (0);
- char buf[32];
-
- printf ("Board: eXalion MPC824x - CHRP (MAP B)\n");
- printf ("Built: %s at %s\n", U_BOOT_DATE, U_BOOT_TIME);
- printf ("Local Bus: %s MHz\n", strmhz (buf, busfreq));
-
- return 0;
-}
-
-int checkflash (void)
-{
- printf ("checkflash\n");
- flash_init ();
- return (0);
-}
-
-phys_size_t initdram (int board_type)
-{
- int i, cnt;
- volatile uchar *base = CONFIG_SYS_SDRAM_BASE;
- volatile ulong *addr;
- ulong save[32];
- ulong val, ret = 0;
-
- for (i = 0, cnt = (CONFIG_SYS_MAX_RAM_SIZE / sizeof (long)) >> 1; cnt > 0;
- cnt >>= 1) {
- addr = (volatile ulong *) base + cnt;
- save[i++] = *addr;
- *addr = ~cnt;
- }
-
- addr = (volatile ulong *) base;
- save[i] = *addr;
- *addr = 0;
-
- if (*addr != 0) {
- *addr = save[i];
- goto Done;
- }
-
- for (cnt = 1; cnt <= CONFIG_SYS_MAX_RAM_SIZE / sizeof (long); cnt <<= 1) {
- addr = (volatile ulong *) base + cnt;
- val = *addr;
- *addr = save[--i];
- if (val != ~cnt) {
- ulong new_bank0_end = cnt * sizeof (long) - 1;
- ulong mear1 = mpc824x_mpc107_getreg (MEAR1);
- ulong emear1 = mpc824x_mpc107_getreg (EMEAR1);
-
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >>
- MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >>
- MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg (MEAR1, mear1);
- mpc824x_mpc107_setreg (EMEAR1, emear1);
-
- ret = cnt * sizeof (long);
- goto Done;
- }
- }
-
- ret = CONFIG_SYS_MAX_RAM_SIZE;
- Done:
- return ret;
-}
-
-int misc_init_r (void)
-{
- pci_dev_t bdf;
- u32 val32;
- u8 val8;
-
- puts ("ISA: ");
- bdf = pci_find_device (PIIX4_VENDOR_ID, PIIX4_ISA_DEV_ID, 0);
- if (bdf == -1) {
- puts ("Unable to find PIIX4 ISA bridge !\n");
- hang ();
- }
-
- /* set device for normal ISA instead EIO */
- pci_read_config_dword (bdf, PCI_CFG_PIIX4_GENCFG, &val32);
- val32 |= 0x00000001;
- pci_write_config_dword (bdf, PCI_CFG_PIIX4_GENCFG, val32);
- printf ("PIIX4 ISA bridge (%d,%d,%d)\n", PCI_BUS (bdf),
- PCI_DEV (bdf), PCI_FUNC (bdf));
-
- puts ("ISA: ");
- bdf = pci_find_device (PIIX4_VENDOR_ID, PIIX4_IDE_DEV_ID, 0);
- if (bdf == -1) {
- puts ("Unable to find PIIX4 IDE controller !\n");
- hang ();
- }
-
- /* Init BMIBA register */
- /* pci_read_config_dword(bdf, PCI_CFG_PIIX4_BMIBA, &val32); */
- /* val32 |= 0x1000; */
- /* pci_write_config_dword(bdf, PCI_CFG_PIIX4_BMIBA, val32); */
-
- /* Enable BUS master and IO access */
- val32 = PCI_COMMAND_MASTER | PCI_COMMAND_IO;
- pci_write_config_dword (bdf, PCI_COMMAND, val32);
-
- /* Set latency */
- pci_read_config_byte (bdf, PCI_LATENCY_TIMER, &val8);
- val8 = 0x40;
- pci_write_config_byte (bdf, PCI_LATENCY_TIMER, val8);
-
- /* Enable Primary ATA/IDE */
- pci_read_config_dword (bdf, PCI_CFG_PIIX4_IDETIM, &val32);
- /* val32 = 0xa307a307; */
- val32 = 0x00008000;
- pci_write_config_dword (bdf, PCI_CFG_PIIX4_IDETIM, val32);
-
-
- printf ("PIIX4 IDE controller (%d,%d,%d)\n", PCI_BUS (bdf),
- PCI_DEV (bdf), PCI_FUNC (bdf));
-
- /* Try to get FAT working... */
- /* fat_register_read(ide_read); */
-
-
- return (0);
-}
-
-/*
- * Show/Init PCI devices on the specified bus number.
- */
-
-void pci_eXalion_fixup_irq (struct pci_controller *hose, pci_dev_t dev)
-{
- unsigned char line;
-
- switch (PCI_DEV (dev)) {
- case 16:
- line = PCI_INT_A;
- break;
- case 17:
- line = PCI_INT_B;
- break;
- case 18:
- line = PCI_INT_C;
- break;
- case 19:
- line = PCI_INT_D;
- break;
-#if defined (CONFIG_MPC8245)
- case 20:
- line = PCI_INT_A;
- break;
- case 21:
- line = PCI_INT_B;
- break;
- case 22:
- line = PCI_INT_NA;
- break;
-#endif
- default:
- line = PCI_INT_A;
- break;
- }
- pci_hose_write_config_byte (hose, dev, PCI_INTERRUPT_LINE, line);
-}
-
-
-/*
- * Initialize PCI Devices, report devices found.
- */
-#ifndef CONFIG_PCI_PNP
-#if defined (CONFIG_MPC8240)
-static struct pci_config_table pci_eXalion_config_table[] = {
- {
- /* Intel 82559ER ethernet controller */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 18, 0x00,
- pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- {
- /* Intel 82371AB PIIX4 PCI to ISA bridge */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 20, 0x00,
- pci_cfgfunc_config_device, {0,
- 0,
- PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
- {
- /* Intel 82371AB PIIX4 IDE controller */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 20, 0x01,
- pci_cfgfunc_config_device, {0,
- 0,
- PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
- {}
-};
-#elif defined (CONFIG_MPC8245)
-static struct pci_config_table pci_eXalion_config_table[] = {
- {
- /* Intel 82559ER ethernet controller */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 17, 0x00,
- pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- {
- /* Intel 82559ER ethernet controller */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 18, 0x00,
- pci_cfgfunc_config_device, {PCI_ENET1_IOADDR,
- PCI_ENET1_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- {
- /* Broadcom BCM5690 Gigabit switch */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 20, 0x00,
- pci_cfgfunc_config_device, {PCI_ENET2_IOADDR,
- PCI_ENET2_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- {
- /* Broadcom BCM5690 Gigabit switch */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 21, 0x00,
- pci_cfgfunc_config_device, {PCI_ENET3_IOADDR,
- PCI_ENET3_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- {
- /* Intel 82371AB PIIX4 PCI to ISA bridge */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 22, 0x00,
- pci_cfgfunc_config_device, {0,
- 0,
- PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
- {
- /* Intel 82371AB PIIX4 IDE controller */
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 22, 0x01,
- pci_cfgfunc_config_device, {0,
- 0,
- PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
- {}
-};
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
-#endif /* #ifndef CONFIG_PCI_PNP */
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table:pci_eXalion_config_table,
- fixup_irq:pci_eXalion_fixup_irq,
-#endif
-};
-
-void pci_init_board (void)
-{
- pci_mpc824x_init (&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/board/eXalion/eXalion.h b/board/eXalion/eXalion.h
deleted file mode 100644
index 7804f4f..0000000
--- a/board/eXalion/eXalion.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * (C) Copyright 2002
- * Torsten Demke, FORCE Computers GmbH. torsten.demke at fci.com
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * James Dougherty (jfd at broadcom.com)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __EXALION_H
-#define __EXALION_H
-
-/* IRQ settings */
-#define PCI_INT_NA (0xff) /* PCI Intr. not used */
-#define PCI_INT_A (0x09) /* PCI Intr. A Interrupt Request Line Nr. */
-#define PCI_INT_B (0x0a) /* PCI Intr. B Interrupt Request Line Nr. */
-#define PCI_INT_C (0x0b) /* PCI Intr. C Interrupt Request Line Nr. */
-#define PCI_INT_D (0x0c) /* PCI Intr. D Interrupt Request Line Nr. */
-#if defined (CPU_MPC8245)
-#define LN_1_INT PCI_INT_B /* ethernet interrupt level */
-#define LN_2_INT PCI_INT_C /* ethernet interrupt level */
-#define BCM_1_INT PCI_INT_A /* BCM5690 interrupt level */
-#define BCM_2_INT PCI_INT_B /* BCM5690 interrupt level */
-#elif defined (CPU_MPC8240)
-#define BCM_INT PCI_INT_B /* BCM5600 interrupt level */
-#define LN_INT PCI_INT_C /* ethernet interrupt level */
-#endif
-
-#ifndef __ASSEMBLY__
-#endif /* !__ASSEMBLY__ */
-
-#endif /* __EXALION_H */
diff --git a/board/eXalion/piix_pci.h b/board/eXalion/piix_pci.h
deleted file mode 100644
index 21c636f..0000000
--- a/board/eXalion/piix_pci.h
+++ /dev/null
@@ -1,156 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * Torsten Demke, FORCE Computers GmbH. torsten.demke at fci.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef _PIIX4_PCI_H
-#define _PIIX4_PCI_H
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <pci.h>
-
-#define PIIX4_VENDOR_ID 0x8086
-#define PIIX4_ISA_DEV_ID 0x7110
-#define PIIX4_IDE_DEV_ID 0x7111
-
-/* Function 0 ISA Bridge */
-#define PCI_CFG_PIIX4_IORT 0x4C /* 8 bit ISA Recovery Timer Reg (default 0x4D) */
-#define PCI_CFG_PIIX4_XBCS 0x4E /* 16 bit XBus Chip select reg (default 0x0003) */
-#define PCI_CFG_PIIX4_PIRQC 0x60 /* PCI IRQ Route Register 4 x 8bit (default )*/
-#define PCI_CFG_PIIX4_SERIRQ 0x64
-#define PCI_CFG_PIIX4_TOM 0x69
-#define PCI_CFG_PIIX4_MSTAT 0x6A
-#define PCI_CFG_PIIX4_MBDMA 0x76
-#define PCI_CFG_PIIX4_APICBS 0x80
-#define PCI_CFG_PIIX4_DLC 0x82
-#define PCI_CFG_PIIX4_PDMACFG 0x90
-#define PCI_CFG_PIIX4_DDMABS 0x92
-#define PCI_CFG_PIIX4_GENCFG 0xB0
-#define PCI_CFG_PIIX4_RTCCFG 0xCB
-
-/* IO Addresses */
-#define PIIX4_ISA_DMA1_CH0BA 0x00
-#define PIIX4_ISA_DMA1_CH0CA 0x01
-#define PIIX4_ISA_DMA1_CH1BA 0x02
-#define PIIX4_ISA_DMA1_CH1CA 0x03
-#define PIIX4_ISA_DMA1_CH2BA 0x04
-#define PIIX4_ISA_DMA1_CH2CA 0x05
-#define PIIX4_ISA_DMA1_CH3BA 0x06
-#define PIIX4_ISA_DMA1_CH3CA 0x07
-#define PIIX4_ISA_DMA1_CMDST 0x08
-#define PIIX4_ISA_DMA1_REQ 0x09
-#define PIIX4_ISA_DMA1_WSBM 0x0A
-#define PIIX4_ISA_DMA1_CH_MOD 0x0B
-#define PIIX4_ISA_DMA1_CLR_PT 0x0C
-#define PIIX4_ISA_DMA1_M_CLR 0x0D
-#define PIIX4_ISA_DMA1_CLR_M 0x0E
-#define PIIX4_ISA_DMA1_RWAMB 0x0F
-
-#define PIIX4_ISA_DMA2_CH0BA 0xC0
-#define PIIX4_ISA_DMA2_CH0CA 0xC1
-#define PIIX4_ISA_DMA2_CH1BA 0xC2
-#define PIIX4_ISA_DMA2_CH1CA 0xC3
-#define PIIX4_ISA_DMA2_CH2BA 0xC4
-#define PIIX4_ISA_DMA2_CH2CA 0xC5
-#define PIIX4_ISA_DMA2_CH3BA 0xC6
-#define PIIX4_ISA_DMA2_CH3CA 0xC7
-#define PIIX4_ISA_DMA2_CMDST 0xD0
-#define PIIX4_ISA_DMA2_REQ 0xD2
-#define PIIX4_ISA_DMA2_WSBM 0xD4
-#define PIIX4_ISA_DMA2_CH_MOD 0xD6
-#define PIIX4_ISA_DMA2_CLR_PT 0xD8
-#define PIIX4_ISA_DMA2_M_CLR 0xDA
-#define PIIX4_ISA_DMA2_CLR_M 0xDC
-#define PIIX4_ISA_DMA2_RWAMB 0xDE
-
-#define PIIX4_ISA_INT1_ICW1 0x20
-#define PIIX4_ISA_INT1_OCW2 0x20
-#define PIIX4_ISA_INT1_OCW3 0x20
-#define PIIX4_ISA_INT1_ICW2 0x21
-#define PIIX4_ISA_INT1_ICW3 0x21
-#define PIIX4_ISA_INT1_ICW4 0x21
-#define PIIX4_ISA_INT1_OCW1 0x21
-
-#define PIIX4_ISA_INT1_ELCR 0x4D0
-
-#define PIIX4_ISA_INT2_ICW1 0xA0
-#define PIIX4_ISA_INT2_OCW2 0xA0
-#define PIIX4_ISA_INT2_OCW3 0xA0
-#define PIIX4_ISA_INT2_ICW2 0xA1
-#define PIIX4_ISA_INT2_ICW3 0xA1
-#define PIIX4_ISA_INT2_ICW4 0xA1
-#define PIIX4_ISA_INT2_OCW1 0xA1
-#define PIIX4_ISA_INT2_IMR 0xA1 /* read only */
-
-#define PIIX4_ISA_INT2_ELCR 0x4D1
-
-#define PIIX4_ISA_TMR0_CNT_ST 0x40
-#define PIIX4_ISA_TMR1_CNT_ST 0x41
-#define PIIX4_ISA_TMR2_CNT_ST 0x42
-#define PIIX4_ISA_TMR_TCW 0x43
-
-#define PIIX4_ISA_RST_XBUS 0x60
-
-#define PIIX4_ISA_NMI_CNT_ST 0x61
-#define PIIX4_ISA_NMI_ENABLE 0x70
-
-#define PIIX4_ISA_RTC_INDEX 0x70
-#define PIIX4_ISA_RTC_DATA 0x71
-#define PIIX4_ISA_RTCEXT_IND 0x70
-#define PIIX4_ISA_RTCEXT_DATA 0x71
-
-#define PIIX4_ISA_DMA1_CH2LPG 0x81
-#define PIIX4_ISA_DMA1_CH3LPG 0x82
-#define PIIX4_ISA_DMA1_CH1LPG 0x83
-#define PIIX4_ISA_DMA1_CH0LPG 0x87
-#define PIIX4_ISA_DMA2_CH2LPG 0x89
-#define PIIX4_ISA_DMA2_CH3LPG 0x8A
-#define PIIX4_ISA_DMA2_CH1LPG 0x8B
-#define PIIX4_ISA_DMA2_LPGRFR 0x8F
-
-#define PIIX4_ISA_PORT_92 0x92
-
-#define PIIX4_ISA_APM_CONTRL 0xB2
-#define PIIX4_ISA_APM_STATUS 0xB3
-
-#define PIIX4_ISA_COCPU_ERROR 0xF0
-
-/* Function 1 IDE Controller */
-#define PCI_CFG_PIIX4_BMIBA 0x20
-#define PCI_CFG_PIIX4_IDETIM 0x40
-#define PCI_CFG_PIIX4_SIDETIM 0x44
-#define PCI_CFG_PIIX4_UDMACTL 0x48
-#define PCI_CFG_PIIX4_UDMATIM 0x4A
-
-/* Function 2 USB Controller */
-#define PCI_CFG_PIIX4_SBRNUM 0x60
-#define PCI_CFG_PIIX4_LEGSUP 0xC0
-
-/* Function 3 Power Management */
-#define PCI_CFG_PIIX4_PMAB 0x40
-#define PCI_CFG_PIIX4_CNTA 0x44
-#define PCI_CFG_PIIX4_CNTB 0x48
-#define PCI_CFG_PIIX4_GPICTL 0x4C
-#define PCI_CFG_PIIX4_DEVRESD 0x50
-#define PCI_CFG_PIIX4_DEVACTA 0x54
-#define PCI_CFG_PIIX4_DEVACTB 0x58
-#define PCI_CFG_PIIX4_DEVRESA 0x5C
-#define PCI_CFG_PIIX4_DEVRESB 0x60
-#define PCI_CFG_PIIX4_DEVRESC 0x64
-#define PCI_CFG_PIIX4_DEVRESE 0x68
-#define PCI_CFG_PIIX4_DEVRESF 0x6C
-#define PCI_CFG_PIIX4_DEVRESG 0x70
-#define PCI_CFG_PIIX4_DEVRESH 0x74
-#define PCI_CFG_PIIX4_DEVRESI 0x78
-#define PCI_CFG_PIIX4_PMMISC 0x80
-#define PCI_CFG_PIIX4_SMBBA 0x90
-
-
-#endif /* _PIIX4_PCI_H */
diff --git a/board/musenki/Kconfig b/board/musenki/Kconfig
deleted file mode 100644
index 26b680f..0000000
--- a/board/musenki/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_MUSENKI
-
-config SYS_BOARD
- default "musenki"
-
-config SYS_CONFIG_NAME
- default "MUSENKI"
-
-endif
diff --git a/board/musenki/MAINTAINERS b/board/musenki/MAINTAINERS
deleted file mode 100644
index 4196c80..0000000
--- a/board/musenki/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MUSENKI BOARD
-#M: Jim Thompson <jim@musenki.com>
-S: Orphan (since 2014-04)
-F: board/musenki/
-F: include/configs/MUSENKI.h
-F: configs/MUSENKI_defconfig
diff --git a/board/musenki/Makefile b/board/musenki/Makefile
deleted file mode 100644
index d2b79ff..0000000
--- a/board/musenki/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = musenki.o flash.o
diff --git a/board/musenki/README b/board/musenki/README
deleted file mode 100644
index 084ab54..0000000
--- a/board/musenki/README
+++ /dev/null
@@ -1,298 +0,0 @@
-U-Boot for a Musenki M-3/M-1 board
----------------------------
-
-Musenki M-1 and M-3 have two banks of flash of 4MB or 8MB each.
-
-In board's notation, bank 0 is the one at the address of 0xFF800000
-and bank 1 is the one at the address of 0xFF000000.
-
-On power-up the processor jumps to the address of 0xFFF00100, the last
-megabyte of the bank 0 of flash.
-
-Thus, U-Boot is configured to reside in flash starting at the address of
-0xFFF00000. The environment space is located in flash separately from
-U-Boot, at the address of 0xFF800000.
-
-There is a Davicom 9102A on-board, but I don't have it working yet.
-
-U-Boot test results
---------------------
-
-x.x Operation on all available serial consoles
-
-x.x.x CONFIG_CONS_INDEX 1
-
-
-U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=> help
-base - print or set address offset
-bdinfo - print Board Info structure
-bootm - boot application image from memory
-bootp - boot image via network using BootP/TFTP protocol
-bootd - boot default, i.e., run 'bootcmd'
-cmp - memory compare
-coninfo - print console devices and informations
-cp - memory copy
-crc32 - checksum calculation
-dcache - enable or disable data cache
-echo - echo args to console
-erase - erase FLASH memory
-flinfo - print FLASH memory information
-go - start application at address 'addr'
-help - print online help
-icache - enable or disable instruction cache
-iminfo - print header information for application image
-loadb - load binary file over serial line (kermit mode)
-loads - load S-Record file over serial line
-loop - infinite loop on address range
-md - memory display
-mm - memory modify (auto-incrementing)
-mtest - simple RAM test
-mw - memory write (fill)
-nm - memory modify (constant address)
-printenv- print environment variables
-protect - enable or disable FLASH write protection
-rarpboot- boot image via network using RARP/TFTP protocol
-reset - Perform RESET of the CPU
-run - run commands in an environment variable
-saveenv - save environment variables to persistent storage
-setenv - set environment variables
-source - run script from memory
-tftpboot- boot image via network using TFTP protocol
- and env variables ipaddr and serverip
-version - print monitor version
-? - alias for 'help'
-
-
-x.x.x CONFIG_CONS_INDEX 2
-
-**** NOT TESTED ****
-
-x.x Flash Driver Operation
-
-
-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-*** Warning - bad CRC, using default environment
-
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=>
-=> md ff800000
-ff800000: 46989bf8 626f6f74 636d643d 626f6f74 F...bootcmd=boot
-ff800010: 6d204646 38323030 30300062 6f6f7464 m FF820000.bootd
-ff800020: 656c6179 3d350062 61756472 6174653d elay=5.baudrate=
-ff800030: 39363030 00636c6f 636b735f 696e5f6d 9600.clocks_in_m
-ff800040: 687a3d31 00737464 696e3d73 65726961 hz=1.stdin=seria
-ff800050: 6c007374 646f7574 3d736572 69616c00 l.stdout=serial.
-ff800060: 73746465 72723d73 65726961 6c006970 stderr=serial.ip
-ff800070: 61646472 3d313932 2e313638 2e302e34 addr=192.168.0.4
-ff800080: 32007365 72766572 69703d31 39322e31 2.serverip=192.1
-ff800090: 36382e30 2e380000 00000000 00000000 68.0.8..........
-ff8000a0: 00000000 00000000 00000000 00000000 ................
-ff8000b0: 00000000 00000000 00000000 00000000 ................
-ff8000c0: 00000000 00000000 00000000 00000000 ................
-ff8000d0: 00000000 00000000 00000000 00000000 ................
-ff8000e0: 00000000 00000000 00000000 00000000 ................
-ff8000f0: 00000000 00000000 00000000 00000000 ................
-=> protect off ff800000 ff81ffff
-Un-Protected 1 sectors
-=> erase ff800000 ff81ffff
-Erase Flash from 0xff800000 to 0xff81ffff
- done
-Erased 1 sectors
-=> md ff800000
-ff800000: ffffffff ffffffff ffffffff ffffffff ................
-ff800010: ffffffff ffffffff ffffffff ffffffff ................
-ff800020: ffffffff ffffffff ffffffff ffffffff ................
-ff800030: ffffffff ffffffff ffffffff ffffffff ................
-ff800040: ffffffff ffffffff ffffffff ffffffff ................
-ff800050: ffffffff ffffffff ffffffff ffffffff ................
-ff800060: ffffffff ffffffff ffffffff ffffffff ................
-ff800070: ffffffff ffffffff ffffffff ffffffff ................
-ff800080: ffffffff ffffffff ffffffff ffffffff ................
-ff800090: ffffffff ffffffff ffffffff ffffffff ................
-ff8000a0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000b0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000c0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000d0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000e0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000f0: ffffffff ffffffff ffffffff ffffffff ................
-
-x.x.x Information
-
-
-U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-*** Warning - bad CRC, using default environment
-
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=> flinfo
-
-Bank # 1: Intel 28F320J3A (32Mbit = 128K x 32)
- Size: 4 MB in 32 Sectors
- Sector Start Addresses:
- FF800000 (RO) FF820000 FF840000 FF860000 FF880000
- FF8A0000 FF8C0000 FF8E0000 FF900000 FF920000
- FF940000 FF960000 FF980000 FF9A0000 FF9C0000
- FF9E0000 FFA00000 FFA20000 FFA40000 FFA60000
- FFA80000 FFAA0000 FFAC0000 FFAE0000 FFB00000
- FFB20000 FFB40000 FFB60000 FFB80000 FFBA0000
- FFBC0000 FFBE0000
-
-Bank # 2: missing or unknown FLASH type
-=>
-
-
-x.x.x Flash Programming
-
-
-U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=>
-=>
-=>
-=> protect off ff800000 ff81ffff
-Un-Protected 1 sectors
-=> cp 0 ff800000 20
-Copy to Flash... done
-=> md ff800000
-ff800000: 37ce33ec 33cc334c 33c031cc 33cc35cc 7.3.3.3L3.1.3.5.
-ff800010: 33ec13ce 30ccb3ec b3c833c4 31c836cc 3...0.....3.1.6.
-ff800020: 33cc3b9d 31ec33ee 13ecf3cc 338833ec 3.;.1.3.....3.3.
-ff800030: 234c33ec 32cc22cc 33883bdc 534433cc #L3.2.".3.;.SD3.
-ff800040: 33cc30c8 31cc32ec 338c33cc 330c33dc 3.0.1.2.3.3.3.3.
-ff800050: 33cc13dc 334c534c b1c433d8 128c13cc 3...3LSL..3.....
-ff800060: 37ec36cd 33dc33cc bbc9f7e8 bbcc77cc 7.6.3.3.......w.
-ff800070: 314c0adc 139c30ed 33cc334c 33c833ec 1L....0.3.3L3.3.
-ff800080: ffffffff ffffffff ffffffff ffffffff ................
-ff800090: ffffffff ffffffff ffffffff ffffffff ................
-ff8000a0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000b0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000c0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000d0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000e0: ffffffff ffffffff ffffffff ffffffff ................
-ff8000f0: ffffffff ffffffff ffffffff ffffffff ................
-
-
-x.x.x Storage of environment variables in flash
-
-
-U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=> printenv
-bootcmd=bootm FF820000
-bootdelay=5
-baudrate=9600
-clocks_in_mhz=1
-stdin=serial
-stdout=serial
-stderr=serial
-
-Environment size: 106/16380 bytes
-=> setenv myvar 1234
-=> saveenv
-Un-Protected 1 sectors
-Erasing Flash...
- done
-Erased 1 sectors
-Saving Environment to Flash...
-Protected 1 sectors
-=> reset
-
-
-U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=> printenv
-bootcmd=bootm FF820000
-bootdelay=5
-baudrate=9600
-clocks_in_mhz=1
-myvar=1234
-stdin=serial
-stdout=serial
-stderr=serial
-
-Environment size: 117/16380 bytes
-
-x.x Image Download and run over serial port
-
-
-U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
-
-CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MUSENKI Local Bus at 100 MHz
-DRAM: 32 MB
-FLASH: 4 MB
-In: serial
-Out: serial
-Err: serial
-Hit any key to stop autoboot: 0
-=> loads
-## Ready for S-Record download ...
-
-## First Load Addr = 0x00040000
-## Last Load Addr = 0x00050177
-## Total Size = 0x00010178 = 65912 Bytes
-## Start Addr = 0x00040004
-=> go 40004
-## Starting application at 0x00040004 ...
-Hello World
-argc = 1
-argv[0] = "40004"
-argv[1] = "<NULL>"
-Hit any key to exit ...
-
-## Application terminated, rc = 0x0
-
-
-x.x Image download and run over ethernet interface
-
-untested (not working yet, actually)
diff --git a/board/musenki/flash.c b/board/musenki/flash.c
deleted file mode 100644
index 080ec7f..0000000
--- a/board/musenki/flash.c
+++ /dev/null
@@ -1,496 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*---------------------------------------------------------------------*/
-#undef DEBUG_FLASH
-
-#ifdef DEBUG_FLASH
-#define DEBUGF(fmt,args...) printf(fmt ,##args)
-#else
-#define DEBUGF(fmt,args...)
-#endif
-/*---------------------------------------------------------------------*/
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_char *addr, flash_info_t *info);
-static int write_data (flash_info_t *info, uchar *dest, uchar data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-
-/*
- * don't ask. its stupid, but more than one soul has had to live with this mistake
- * "swaptab[i]" is the value of "i" with the bits reversed.
- */
-
-#define MUSENKI_BROKEN_FLASH 1
-
-#ifdef MUSENKI_BROKEN_FLASH
-unsigned char swaptab[256] = {
- 0x00, 0x80, 0x40, 0xc0, 0x20, 0xa0, 0x60, 0xe0,
- 0x10, 0x90, 0x50, 0xd0, 0x30, 0xb0, 0x70, 0xf0,
- 0x08, 0x88, 0x48, 0xc8, 0x28, 0xa8, 0x68, 0xe8,
- 0x18, 0x98, 0x58, 0xd8, 0x38, 0xb8, 0x78, 0xf8,
- 0x04, 0x84, 0x44, 0xc4, 0x24, 0xa4, 0x64, 0xe4,
- 0x14, 0x94, 0x54, 0xd4, 0x34, 0xb4, 0x74, 0xf4,
- 0x0c, 0x8c, 0x4c, 0xcc, 0x2c, 0xac, 0x6c, 0xec,
- 0x1c, 0x9c, 0x5c, 0xdc, 0x3c, 0xbc, 0x7c, 0xfc,
- 0x02, 0x82, 0x42, 0xc2, 0x22, 0xa2, 0x62, 0xe2,
- 0x12, 0x92, 0x52, 0xd2, 0x32, 0xb2, 0x72, 0xf2,
- 0x0a, 0x8a, 0x4a, 0xca, 0x2a, 0xaa, 0x6a, 0xea,
- 0x1a, 0x9a, 0x5a, 0xda, 0x3a, 0xba, 0x7a, 0xfa,
- 0x06, 0x86, 0x46, 0xc6, 0x26, 0xa6, 0x66, 0xe6,
- 0x16, 0x96, 0x56, 0xd6, 0x36, 0xb6, 0x76, 0xf6,
- 0x0e, 0x8e, 0x4e, 0xce, 0x2e, 0xae, 0x6e, 0xee,
- 0x1e, 0x9e, 0x5e, 0xde, 0x3e, 0xbe, 0x7e, 0xfe,
- 0x01, 0x81, 0x41, 0xc1, 0x21, 0xa1, 0x61, 0xe1,
- 0x11, 0x91, 0x51, 0xd1, 0x31, 0xb1, 0x71, 0xf1,
- 0x09, 0x89, 0x49, 0xc9, 0x29, 0xa9, 0x69, 0xe9,
- 0x19, 0x99, 0x59, 0xd9, 0x39, 0xb9, 0x79, 0xf9,
- 0x05, 0x85, 0x45, 0xc5, 0x25, 0xa5, 0x65, 0xe5,
- 0x15, 0x95, 0x55, 0xd5, 0x35, 0xb5, 0x75, 0xf5,
- 0x0d, 0x8d, 0x4d, 0xcd, 0x2d, 0xad, 0x6d, 0xed,
- 0x1d, 0x9d, 0x5d, 0xdd, 0x3d, 0xbd, 0x7d, 0xfd,
- 0x03, 0x83, 0x43, 0xc3, 0x23, 0xa3, 0x63, 0xe3,
- 0x13, 0x93, 0x53, 0xd3, 0x33, 0xb3, 0x73, 0xf3,
- 0x0b, 0x8b, 0x4b, 0xcb, 0x2b, 0xab, 0x6b, 0xeb,
- 0x1b, 0x9b, 0x5b, 0xdb, 0x3b, 0xbb, 0x7b, 0xfb,
- 0x07, 0x87, 0x47, 0xc7, 0x27, 0xa7, 0x67, 0xe7,
- 0x17, 0x97, 0x57, 0xd7, 0x37, 0xb7, 0x77, 0xf7,
- 0x0f, 0x8f, 0x4f, 0xcf, 0x2f, 0xaf, 0x6f, 0xef,
- 0x1f, 0x9f, 0x5f, 0xdf, 0x3f, 0xbf, 0x7f, 0xff,
-};
-
-#define BS(b) (swaptab[b])
-
-#else
-
-#define BS(b) (b)
-
-#endif
-
-#define BYTEME(x) ((x) & 0xFF)
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- unsigned long size_b0, size_b1;
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
-
- DEBUGF("\n## Get flash bank 1 size @ 0x%08x\n",CONFIG_SYS_FLASH_BASE0_PRELIM);
-
- size_b0 = flash_get_size((vu_char *)CONFIG_SYS_FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0: "
- "ID 0x%lx, Size = 0x%08lx = %ld MB\n",
- flash_info[0].flash_id,
- size_b0, size_b0<<20);
- }
-
- DEBUGF("## Get flash bank 2 size @ 0x%08x\n",CONFIG_SYS_FLASH_BASE1_PRELIM);
- size_b1 = flash_get_size((vu_char *)CONFIG_SYS_FLASH_BASE1_PRELIM, &flash_info[1]);
-
- DEBUGF("## Prelim. Flash bank sizes: %08lx + 0x%08lx\n",size_b0,size_b1);
-
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_info[0].size = size_b0;
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- DEBUGF("protect monitor %x @ %x\n", CONFIG_SYS_MONITOR_BASE, monitor_flash_len);
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- DEBUGF("protect environtment %x @ %x\n", CONFIG_ENV_ADDR, CONFIG_ENV_SECT_SIZE);
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1,
- &flash_info[0]);
-#endif
-
- if (size_b1) {
- flash_info[1].size = size_b1;
- flash_get_offsets (CONFIG_SYS_FLASH_BASE + size_b0, &flash_info[1]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[1]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1,
- &flash_info[1]);
-#endif
- } else {
- flash_info[1].flash_id = FLASH_UNKNOWN;
- flash_info[1].sector_count = -1;
- flash_info[1].size = 0;
- }
-
- DEBUGF("## Final Flash bank sizes: %08lx + 0x%08lx\n",size_b0,size_b1);
-
- return (size_b0 + size_b1);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- base += 0x00020000; /* 128k per bank */
- }
- return;
-
- default:
- printf ("Don't know sector ofsets for flash type 0x%lx\n", info->flash_id);
- return;
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_FUJ: printf ("Fujitsu "); break;
- case FLASH_MAN_SST: printf ("SST "); break;
- case FLASH_MAN_STM: printf ("STM "); break;
- case FLASH_MAN_INTEL: printf ("Intel "); break;
- case FLASH_MAN_MT: printf ("MT "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F320J3A: printf ("28F320J3A (32Mbit = 128K x 32)\n");
- break;
- case FLASH_28F640J3A: printf ("28F640J3A (64Mbit = 128K x 64)\n");
- break;
- case FLASH_28F128J3A: printf ("28F128J3A (128Mbit = 128K x 128)\n");
- break;
- default: printf ("Unknown Chip Type\n");
- break;
- }
-
- if (info->size >= (1 << 20)) {
- i = 20;
- } else {
- i = 10;
- }
- printf (" Size: %ld %cB in %d Sectors\n",
- info->size >> i,
- (i == 20) ? 'M' : 'k',
- info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (vu_char *addr, flash_info_t *info)
-{
- vu_char manuf, device;
-
- addr[0] = BS(0x90);
- manuf = BS(addr[0]);
- DEBUGF("Manuf. ID @ 0x%08lx: 0x%08x\n", (vu_char *)addr, manuf);
-
- switch (manuf) {
- case BYTEME(AMD_MANUFACT):
- info->flash_id = FLASH_MAN_AMD;
- break;
- case BYTEME(FUJ_MANUFACT):
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case BYTEME(SST_MANUFACT):
- info->flash_id = FLASH_MAN_SST;
- break;
- case BYTEME(STM_MANUFACT):
- info->flash_id = FLASH_MAN_STM;
- break;
- case BYTEME(INTEL_MANUFACT):
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = BS(0xFF); /* restore read mode, (yes, BS is a NOP) */
- return 0; /* no or unknown flash */
- }
-
- device = BS(addr[2]); /* device ID */
-
- DEBUGF("Device ID @ 0x%08x: 0x%08x\n", (&addr[1]), device);
-
- switch (device) {
- case BYTEME(INTEL_ID_28F320J3A):
- info->flash_id += FLASH_28F320J3A;
- info->sector_count = 32;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case BYTEME(INTEL_ID_28F640J3A):
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case BYTEME(INTEL_ID_28F128J3A):
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- addr[0] = BS(0xFF); /* restore read mode (yes, a NOP) */
- return 0; /* => no or unknown flash */
-
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = BS(0xFF); /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) {
- printf ("Can erase only Intel flash types - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_char *addr = (vu_char *)(info->start[sect]);
- unsigned long status;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = BS(0x50); /* clear status register */
- *addr = BS(0x20); /* erase setup */
- *addr = BS(0xD0); /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag) {
- enable_interrupts();
- }
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((status = BS(*addr)) & BYTEME(0x00800080)) != BYTEME(0x00800080)) {
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = BS(0xB0); /* suspend erase */
- *addr = BS(0xFF); /* reset to read mode */
- return 1;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- *addr = BS(0xFF); /* reset to read mode */
- }
- }
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-#define FLASH_WIDTH 1 /* flash bus width in bytes */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- uchar *wp = (uchar *)addr;
- int rc;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
- while (cnt > 0) {
- if ((rc = write_data(info, wp, *src)) != 0) {
- return rc;
- }
- wp++;
- src++;
- cnt--;
- }
-
- return cnt;
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t *info, uchar *dest, uchar data)
-{
- vu_char *addr = (vu_char *)dest;
- ulong status;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((BS(*addr) & data) != data) {
- return 2;
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = BS(0x40); /* write setup */
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag) {
- enable_interrupts();
- }
-
- start = get_timer (0);
-
- while (((status = BS(*addr)) & BYTEME(0x00800080)) != BYTEME(0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = BS(0xFF); /* restore read mode */
- return 1;
- }
- }
-
- *addr = BS(0xFF); /* restore read mode */
-
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/musenki/musenki.c b/board/musenki/musenki.c
deleted file mode 100644
index aa92fc4..0000000
--- a/board/musenki/musenki.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * (C) Copyright 2001
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <pci.h>
-#include <netdev.h>
-
-int checkboard (void)
-{
- ulong busfreq = get_bus_freq(0);
- char buf[32];
-
- printf("Board: MUSENKI Local Bus at %s MHz\n", strmhz(buf, busfreq));
- return 0;
-
-}
-
-#if 0 /* NOT USED */
-int checkflash (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("## Test not implemented yet ##\n");
-
- return (0);
-}
-#endif
-
-phys_size_t initdram (int board_type)
-{
- long size;
- long new_bank0_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-/*
- * Initialize PCI Devices
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_sandpoint_config_table[] = {
-#if 0
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- 0x0, 0x0, 0x0, /* unknown eth0 divice */
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- 0x0, 0x0, 0x0, /* unknown eth1 device */
- pci_cfgfunc_config_device, { PCI_ENET1_IOADDR,
- PCI_ENET1_MEMADDR,
- PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER }},
-#endif
- { }
-};
-#endif
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_sandpoint_config_table,
-#endif
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/board/mvblue/Kconfig b/board/mvblue/Kconfig
deleted file mode 100644
index cee206b..0000000
--- a/board/mvblue/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_MVBLUE
-
-config SYS_BOARD
- default "mvblue"
-
-config SYS_CONFIG_NAME
- default "MVBLUE"
-
-endif
diff --git a/board/mvblue/MAINTAINERS b/board/mvblue/MAINTAINERS
deleted file mode 100644
index 5955f1a..0000000
--- a/board/mvblue/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MVBLUE BOARD
-#M: -
-S: Maintained
-F: board/mvblue/
-F: include/configs/MVBLUE.h
-F: configs/MVBLUE_defconfig
diff --git a/board/mvblue/Makefile b/board/mvblue/Makefile
deleted file mode 100644
index 76c10f8..0000000
--- a/board/mvblue/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = mvblue.o flash.o
diff --git a/board/mvblue/flash.c b/board/mvblue/flash.c
deleted file mode 100644
index 5dd658f..0000000
--- a/board/mvblue/flash.c
+++ /dev/null
@@ -1,570 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- * (C) Copyright 2001-2003
- *
- * Changes for MATRIX Vision mvBLUE devices
- * MATRIX Vision GmbH / hg,as info at matrix-vision.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-
-#if 0
- #define mvdebug(p) printf ##p
-#else
- #define mvdebug(p)
-#endif
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-#define FLASH_BUS_WIDTH 8
-
-#if (FLASH_BUS_WIDTH==32)
- #define FLASH_DATA_MASK 0xffffffff
- #define FLASH_SHIFT 1
- #define FDT vu_long
-#elif (FLASH_BUS_WIDTH==16)
- #define FLASH_DATA_MASK 0xff
- #define FLASH_SHIFT 0
- #define FDT vu_short
-#elif (FLASH_BUS_WIDTH==8)
- #define FLASH_DATA_MASK 0xff
- #define FLASH_SHIFT 0
- #define FDT vu_char
-#else
- #error FLASH_BUS_WIDTH undefined
-#endif
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *address, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-/*-----------------------------------------------------------------------
- */
-unsigned long flash_init (void)
-{
- unsigned long size_b0;
- int i;
-
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- size_b0 = flash_get_size((vu_long *)0xffc00000, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH : Size = 0x%08lx = %ld MB\n",
- size_b0, size_b0<<20);
- }
-
- flash_get_offsets (0xffc00000, &flash_info[0]);
- flash_info[0].size = size_b0;
-
- /* monitor protection OFF by default */
- flash_protect ( FLAG_PROTECT_CLEAR, 0xffc00000, 0x2000, flash_info );
-
- return size_b0;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- /* set up sector start address table */
- if (info->flash_id & FLASH_BTYPE)
- { /* bottom boot sector types - these are the useful ones! */
- /* set sector offsets for bottom boot block type */
- if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B)
- { /* AMDLV320B has 8 x 8k bottom boot sectors */
- for (i = 0; i < 8; i++) /* +8k */
- info->start[i] = base + (i * (0x00002000 << FLASH_SHIFT));
- for (; i < info->sector_count; i++) /* +64k */
- info->start[i] = base + (i * (0x00010000 << FLASH_SHIFT)) - (0x00070000 << FLASH_SHIFT);
- }
- else
- { /* other types have 4 bottom boot sectors (16,8,8,32) */
- i = 0;
- info->start[i++] = base + 0x00000000; /* - */
- info->start[i++] = base + (0x00004000 << FLASH_SHIFT); /* +16k */
- info->start[i++] = base + (0x00006000 << FLASH_SHIFT); /* +8k */
- info->start[i++] = base + (0x00008000 << FLASH_SHIFT); /* +8k */
- info->start[i++] = base + (0x00010000 << FLASH_SHIFT); /* +32k */
- for (; i < info->sector_count; i++) /* +64k */
- info->start[i] = base + (i * (0x00010000 << FLASH_SHIFT)) - (0x00030000 << FLASH_SHIFT);
- }
- }
- else
- { /* top boot sector types - not so useful */
- /* set sector offsets for top boot block type */
- if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T)
- { /* AMDLV320T has 8 x 8k top boot sectors */
- for (i = 0; i < info->sector_count - 8; i++) /* +64k */
- info->start[i] = base + (i * (0x00010000 << FLASH_SHIFT));
- for (; i < info->sector_count; i++) /* +8k */
- info->start[i] = base + (i * (0x00002000 << FLASH_SHIFT));
- }
- else
- { /* other types have 4 top boot sectors (32,8,8,16) */
- for (i = 0; i < info->sector_count - 4; i++) /* +64k */
- info->start[i] = base + (i * (0x00010000 << FLASH_SHIFT));
-
- info->start[i++] = base + info->size - (0x00010000 << FLASH_SHIFT); /* -32k */
- info->start[i++] = base + info->size - (0x00008000 << FLASH_SHIFT); /* -8k */
- info->start[i++] = base + info->size - (0x00006000 << FLASH_SHIFT); /* -8k */
- info->start[i] = base + info->size - (0x00004000 << FLASH_SHIFT); /* -16k */
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_FUJ: printf ("FUJITSU "); break;
- case FLASH_MAN_STM: printf ("ST "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM160B: printf ("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T: printf ("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B: printf ("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T: printf ("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- case FLASH_STMW320DB: printf ("M29W320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_STMW320DT: printf ("M29W320T (32 Mbit, top boot sector)\n");
- break;
- default: printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n", info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s", info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-#define AMD_ID_LV160T_MVS (AMD_ID_LV160T & FLASH_DATA_MASK)
-#define AMD_ID_LV160B_MVS (AMD_ID_LV160B & FLASH_DATA_MASK)
-#define AMD_ID_LV320T_MVS (AMD_ID_LV320T & FLASH_DATA_MASK)
-#define AMD_ID_LV320B_MVS (AMD_ID_LV320B & FLASH_DATA_MASK)
-#define STM_ID_W320DT_MVS (STM_ID_29W320DT & FLASH_DATA_MASK)
-#define STM_ID_W320DB_MVS (STM_ID_29W320DB & FLASH_DATA_MASK)
-#define AMD_MANUFACT_MVS (AMD_MANUFACT & FLASH_DATA_MASK)
-#define FUJ_MANUFACT_MVS (FUJ_MANUFACT & FLASH_DATA_MASK)
-#define STM_MANUFACT_MVS (STM_MANUFACT & FLASH_DATA_MASK)
-
-#if (FLASH_BUS_WIDTH >= 16)
- #define AUTOSELECT_ADDR1 0x0555
- #define AUTOSELECT_ADDR2 0x02AA
- #define AUTOSELECT_ADDR3 AUTOSELECT_ADDR1
-#else
- #define AUTOSELECT_ADDR1 0x0AAA
- #define AUTOSELECT_ADDR2 0x0555
- #define AUTOSELECT_ADDR3 AUTOSELECT_ADDR1
-#endif
-
-#define AUTOSELECT_DATA1 (0x00AA00AA & FLASH_DATA_MASK)
-#define AUTOSELECT_DATA2 (0x00550055 & FLASH_DATA_MASK)
-#define AUTOSELECT_DATA3 (0x00900090 & FLASH_DATA_MASK)
-
-#define RESET_BANK_DATA (0x00F000F0 & FLASH_DATA_MASK)
-
-
-static ulong flash_get_size (vu_long *address, flash_info_t *info)
-{
- short i;
- FDT value;
- FDT *addr = (FDT *)address;
-
- ulong base = (ulong)address;
- addr[AUTOSELECT_ADDR1] = AUTOSELECT_DATA1;
- addr[AUTOSELECT_ADDR2] = AUTOSELECT_DATA2;
- addr[AUTOSELECT_ADDR3] = AUTOSELECT_DATA3;
- __asm__ __volatile__("sync");
-
- udelay(180);
-
- value = addr[0]; /* manufacturer ID */
- switch (value) {
- case AMD_MANUFACT_MVS:
- info->flash_id = FLASH_MAN_AMD;
- break;
- case FUJ_MANUFACT_MVS:
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case STM_MANUFACT_MVS:
- info->flash_id = FLASH_MAN_STM;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
-#if (FLASH_BUS_WIDTH >= 16)
- value = addr[1]; /* device ID */
-#else
- value = addr[2]; /* device ID */
-#endif
-
- switch (value) {
- case AMD_ID_LV160T_MVS:
- info->flash_id += FLASH_AM160T;
- info->sector_count = 37;
- info->size = (0x00200000 << FLASH_SHIFT);
- break; /* => 2 or 4 MB */
-
- case AMD_ID_LV160B_MVS:
- info->flash_id += FLASH_AM160B;
- info->sector_count = 37;
- info->size = (0x00200000 << FLASH_SHIFT);
- break; /* => 2 or 4 MB */
-
- case AMD_ID_LV320T_MVS:
- info->flash_id += FLASH_AM320T;
- info->sector_count = 71;
- info->size = (0x00400000 << FLASH_SHIFT);
- break; /* => 4 or 8 MB */
-
- case AMD_ID_LV320B_MVS:
- info->flash_id += FLASH_AM320B;
- info->sector_count = 71;
- info->size = (0x00400000 << FLASH_SHIFT);
- break; /* => 4 or 8MB */
-
- case STM_ID_W320DT_MVS:
- info->flash_id += FLASH_STMW320DT;
- info->sector_count = 67;
- info->size = (0x00400000 << FLASH_SHIFT);
- break; /* => 4 or 8 MB */
-
- case STM_ID_W320DB_MVS:
- info->flash_id += FLASH_STMW320DB;
- info->sector_count = 67;
- info->size = (0x00400000 << FLASH_SHIFT);
- break; /* => 4 or 8MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
-
- }
-
- /* set up sector start address table */
- flash_get_offsets (base, info);
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (FDT *)(info->start[i]);
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (FDT *)info->start[0];
- *addr = RESET_BANK_DATA; /* reset bank */
- }
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-#if (FLASH_BUS_WIDTH >= 16)
- #define ERASE_ADDR1 0x0555
- #define ERASE_ADDR2 0x02AA
-#else
- #define ERASE_ADDR1 0x0AAA
- #define ERASE_ADDR2 0x0555
-#endif
-
-#define ERASE_ADDR3 ERASE_ADDR1
-#define ERASE_ADDR4 ERASE_ADDR1
-#define ERASE_ADDR5 ERASE_ADDR2
-
-#define ERASE_DATA1 (0x00AA00AA & FLASH_DATA_MASK)
-#define ERASE_DATA2 (0x00550055 & FLASH_DATA_MASK)
-#define ERASE_DATA3 (0x00800080 & FLASH_DATA_MASK)
-#define ERASE_DATA4 ERASE_DATA1
-#define ERASE_DATA5 ERASE_DATA2
-
-#define ERASE_SECTOR_DATA (0x00300030 & FLASH_DATA_MASK)
-#define ERASE_CHIP_DATA (0x00100010 & FLASH_DATA_MASK)
-#define ERASE_CONFIRM_DATA (0x00800080 & FLASH_DATA_MASK)
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- FDT *addr = (FDT *)(info->start[0]);
-
- int prot, sect, l_sect, flag;
- ulong start, now, last;
-
- __asm__ __volatile__ ("sync");
- addr[0] = 0xf0;
- udelay(1000);
-
- printf("\nflash_erase: first = %d @ 0x%08lx\n", s_first, info->start[s_first] );
- printf(" last = %d @ 0x%08lx\n", s_last , info->start[s_last ] );
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) || (info->flash_id > FLASH_AMD_COMP)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n", info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[ERASE_ADDR1] = ERASE_DATA1;
- addr[ERASE_ADDR2] = ERASE_DATA2;
- addr[ERASE_ADDR3] = ERASE_DATA3;
- addr[ERASE_ADDR4] = ERASE_DATA4;
- addr[ERASE_ADDR5] = ERASE_DATA5;
-
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) {
- addr = (FDT *)(info->start[sect]);
- addr[0] = ERASE_SECTOR_DATA;
- l_sect = sect;
- }
- }
-
- if (flag)
- enable_interrupts();
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (FDT *)(info->start[l_sect]);
-
- while ((addr[0] & ERASE_CONFIRM_DATA) != ERASE_CONFIRM_DATA) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
-DONE:
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-#define BUFF_INC 4
- ulong cp, wp, data;
- int i, l, rc;
-
- mvdebug (("+write_buff %p ==> 0x%08lx, count = 0x%08lx\n", src, addr, cnt));
-
- wp = (addr & ~3); /* get lower word aligned address */
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- mvdebug ((" handle unaligned start bytes (cnt = 0x%08lx)\n", cnt));
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<BUFF_INC && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<BUFF_INC; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += BUFF_INC;
- }
-
- /*
- * handle (half)word aligned part
- */
- mvdebug ((" handle word aligned part (cnt = 0x%08lx)\n", cnt));
- while (cnt >= BUFF_INC) {
- data = 0;
- for (i=0; i<BUFF_INC; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += BUFF_INC;
- cnt -= BUFF_INC;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- mvdebug ((" handle unaligned tail bytes (cnt = 0x%08lx)\n", cnt));
- data = 0;
- for (i=0, cp=wp; i<BUFF_INC && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<BUFF_INC; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-#if (FLASH_BUS_WIDTH >= 16)
- #define WRITE_ADDR1 0x0555
- #define WRITE_ADDR2 0x02AA
-#else
- #define WRITE_ADDR1 0x0AAA
- #define WRITE_ADDR2 0x0555
- #define WRITE_ADDR3 WRITE_ADDR1
-#endif
-
-#define WRITE_DATA1 (0x00AA00AA & FLASH_DATA_MASK)
-#define WRITE_DATA2 (0x00550055 & FLASH_DATA_MASK)
-#define WRITE_DATA3 (0x00A000A0 & FLASH_DATA_MASK)
-
-#define WRITE_CONFIRM_DATA ERASE_CONFIRM_DATA
-
-/*-----------------------------------------------------------------------
- * Write a byte to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_char (flash_info_t *info, ulong dest, uchar data)
-{
- vu_char *addr = (vu_char *)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_char *)dest) & data) != data) {
- printf(" *** ERROR: Flash not erased !\n");
- return (2);
- }
- flag = disable_interrupts();
-
- addr[WRITE_ADDR1] = WRITE_DATA1;
- addr[WRITE_ADDR2] = WRITE_DATA2;
- addr[WRITE_ADDR3] = WRITE_DATA3;
- *((vu_char *)dest) = data;
-
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- addr = (vu_char *)dest;
- while (( (*addr) & WRITE_CONFIRM_DATA) != (data & WRITE_CONFIRM_DATA)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- printf(" *** ERROR: Flash write timeout !");
- return (1);
- }
- }
- mvdebug (("-write_byte\n"));
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- int i,
- result = 0;
-
- mvdebug (("+write_word : 0x%08lx @ 0x%08lx\n", data, dest));
- for ( i=0; (i < 4) && (result == 0); i++, dest+=1 )
- result = write_char (info, dest, (data >> (8*(3-i))) & 0xff );
- mvdebug (("-write_word\n"));
- return result;
-}
-/*---------------------------------------------------------------- */
diff --git a/board/mvblue/mvblue.c b/board/mvblue/mvblue.c
deleted file mode 100644
index 63503e8..0000000
--- a/board/mvblue/mvblue.c
+++ /dev/null
@@ -1,253 +0,0 @@
-/*
- * GNU General Public License for more details.
- *
- * MATRIX Vision GmbH / June 2002-Nov 2003
- * Andre Schwarz
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/io.h>
-#include <ns16550.h>
-#include <netdev.h>
-
-#ifdef CONFIG_PCI
-#include <pci.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-u32 get_BoardType (void);
-
-#define PCI_CONFIG(b,d,f,r) cpu_to_le32(0x80000000 | ((b&0xff)<<16) \
- | ((d&0x1f)<<11) \
- | ((f&0x7)<<7) \
- | (r&0xfc) )
-
-int mv_pci_read (int bus, int dev, int func, int reg)
-{
- *(u32 *) (0xfec00cf8) = PCI_CONFIG (bus, dev, func, reg);
- asm ("sync");
- return cpu_to_le32 (*(u32 *) (0xfee00cfc));
-}
-
-u32 get_BoardType ()
-{
- return (mv_pci_read (0, 0xe, 0, 0) == 0x06801095 ? 0 : 1);
-}
-
-void init_2nd_DUART (void)
-{
- NS16550_t console = (NS16550_t) CONFIG_SYS_NS16550_COM2;
- int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE;
-
- *(u8 *) (0xfc004511) = 0x1;
- NS16550_init (console, clock_divisor);
-}
-void hw_watchdog_reset (void)
-{
- if (get_BoardType () == 0) {
- *(u32 *) (0xff000005) = 0;
- asm ("sync");
- }
-}
-int checkboard (void)
-{
- ulong busfreq = get_bus_freq (0);
- char buf[32];
- u32 BoardType = get_BoardType ();
- char *BoardName[2] = { "mvBlueBOX", "mvBlueLYNX" };
- char *p;
-
- hw_watchdog_reset ();
-
- printf ("U-Boot (%s) running on mvBLUE device.\n", MV_VERSION);
- printf (" Found %s running@%s MHz memory clock.\n",
- BoardName[BoardType], strmhz (buf, busfreq));
-
- init_2nd_DUART ();
-
- if ((p = getenv ("console_nr")) != NULL) {
- unsigned long con_nr = simple_strtoul (p, NULL, 10) & 3;
-
- gd->baudrate &= ~3;
- gd->baudrate |= con_nr & 3;
- }
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- long size;
- long new_bank0_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-/* ------------------------------------------------------------------------- */
-u8 *dhcp_vendorex_prep (u8 * e)
-{
- char *ptr;
-
- /* DHCP vendor-class-identifier = 60 */
- if ((ptr = getenv ("dhcp_vendor-class-identifier"))) {
- *e++ = 60;
- *e++ = strlen (ptr);
- while (*ptr)
- *e++ = *ptr++;
- }
- /* my DHCP_CLIENT_IDENTIFIER = 61 */
- if ((ptr = getenv ("dhcp_client_id"))) {
- *e++ = 61;
- *e++ = strlen (ptr);
- while (*ptr)
- *e++ = *ptr++;
- }
- return e;
-}
-
-u8 *dhcp_vendorex_proc (u8 * popt)
-{
- return NULL;
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Initialize PCI Devices
- */
-#ifdef CONFIG_PCI
-void pci_mvblue_clear_base (struct pci_controller *hose, pci_dev_t dev)
-{
- u32 cnt;
-
- printf ("clear base @ dev/func 0x%02x/0x%02x ... ", PCI_DEV (dev),
- PCI_FUNC (dev));
- for (cnt = 0; cnt < 6; cnt++)
- pci_hose_write_config_dword (hose, dev, 0x10 + (4 * cnt),
- 0x0);
- printf ("done\n");
-}
-
-void duart_setup (u32 base, u16 divisor)
-{
- printf ("duart setup ...");
- out_8 ((u8 *) (CONFIG_SYS_ISA_IO + base + 3), 0x80);
- out_8 ((u8 *) (CONFIG_SYS_ISA_IO + base + 0), divisor & 0xff);
- out_8 ((u8 *) (CONFIG_SYS_ISA_IO + base + 1), divisor >> 8);
- out_8 ((u8 *) (CONFIG_SYS_ISA_IO + base + 3), 0x03);
- out_8 ((u8 *) (CONFIG_SYS_ISA_IO + base + 4), 0x03);
- out_8 ((u8 *) (CONFIG_SYS_ISA_IO + base + 2), 0x07);
- printf ("done\n");
-}
-
-void pci_mvblue_fixup_irq_behind_bridge (struct pci_controller *hose,
- pci_dev_t bridge, unsigned char irq)
-{
- pci_dev_t d;
- unsigned char bus;
- unsigned short vendor, class;
-
- pci_hose_read_config_byte (hose, bridge, PCI_SECONDARY_BUS, &bus);
- for (d = PCI_BDF (bus, 0, 0);
- d < PCI_BDF (bus, PCI_MAX_PCI_DEVICES - 1,
- PCI_MAX_PCI_FUNCTIONS - 1);
- d += PCI_BDF (0, 0, 1)) {
- pci_hose_read_config_word (hose, d, PCI_VENDOR_ID, &vendor);
- if (vendor != 0xffff && vendor != 0x0000) {
- pci_hose_read_config_word (hose, d, PCI_CLASS_DEVICE,
- &class);
- if (class == PCI_CLASS_BRIDGE_PCI)
- pci_mvblue_fixup_irq_behind_bridge (hose, d,
- irq);
- else
- pci_hose_write_config_byte (hose, d,
- PCI_INTERRUPT_LINE,
- irq);
- }
- }
-}
-
-#define MV_MAX_PCI_BUSSES 3
-#define SLOT0_IRQ 3
-#define SLOT1_IRQ 4
-void pci_mvblue_fixup_irq (struct pci_controller *hose, pci_dev_t dev)
-{
- unsigned char line = 0xff;
- unsigned short class;
-
- if (PCI_BUS (dev) == 0) {
- switch (PCI_DEV (dev)) {
- case 0xd:
- if (get_BoardType () == 0) {
- line = 1;
- } else
- /* mvBL */
- line = 2;
- break;
- case 0xe:
- /* mvBB: IDE */
- line = 2;
- pci_hose_write_config_byte (hose, dev, 0x8a, 0x20);
- break;
- case 0xf:
- /* mvBB: Slot0 (Grabber) */
- pci_hose_read_config_word (hose, dev,
- PCI_CLASS_DEVICE, &class);
- if (class == PCI_CLASS_BRIDGE_PCI) {
- pci_mvblue_fixup_irq_behind_bridge (hose, dev,
- SLOT0_IRQ);
- line = 0xff;
- } else
- line = SLOT0_IRQ;
- break;
- case 0x10:
- /* mvBB: Slot1 */
- pci_hose_read_config_word (hose, dev,
- PCI_CLASS_DEVICE, &class);
- if (class == PCI_CLASS_BRIDGE_PCI) {
- pci_mvblue_fixup_irq_behind_bridge (hose, dev,
- SLOT1_IRQ);
- line = 0xff;
- } else
- line = SLOT1_IRQ;
- break;
- default:
- printf ("***pci_scan: illegal dev = 0x%08x\n",
- PCI_DEV (dev));
- line = 0xff;
- break;
- }
- pci_hose_write_config_byte (hose, dev, PCI_INTERRUPT_LINE,
- line);
- }
-}
-
-struct pci_controller hose = {
- fixup_irq:pci_mvblue_fixup_irq
-};
-
-void pci_init_board (void)
-{
- pci_mpc824x_init (&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
-#endif
diff --git a/board/mvblue/u-boot.lds b/board/mvblue/u-boot.lds
deleted file mode 100644
index 5034a96..0000000
--- a/board/mvblue/u-boot.lds
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * (C) Copyright 2001-2007
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- .text :
- {
- arch/powerpc/cpu/mpc824x/start.o (.text*)
- lib/built-in.o (.text*)
- net/built-in.o (.text*)
- drivers/pci/built-in.o (.text*)
- arch/powerpc/cpu/mpc824x/built-in.o (.text*)
- board/mvblue/built-in.o (.text*)
- arch/powerpc/lib/built-in.o (.text*)
-
- . = DEFINED(env_offset) ? env_offset : .;
- common/env_embedded.o (.ppcenv*)
-
- *(.text*)
- . = ALIGN(16);
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/board/sandpoint/Kconfig b/board/sandpoint/Kconfig
deleted file mode 100644
index c19b63e..0000000
--- a/board/sandpoint/Kconfig
+++ /dev/null
@@ -1,19 +0,0 @@
-if TARGET_SANDPOINT8240
-
-config SYS_BOARD
- default "sandpoint"
-
-config SYS_CONFIG_NAME
- default "Sandpoint8240"
-
-endif
-
-if TARGET_SANDPOINT8245
-
-config SYS_BOARD
- default "sandpoint"
-
-config SYS_CONFIG_NAME
- default "Sandpoint8245"
-
-endif
diff --git a/board/sandpoint/MAINTAINERS b/board/sandpoint/MAINTAINERS
deleted file mode 100644
index 569cf42..0000000
--- a/board/sandpoint/MAINTAINERS
+++ /dev/null
@@ -1,12 +0,0 @@
-SANDPOINT BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/sandpoint/
-F: include/configs/Sandpoint8240.h
-F: configs/Sandpoint8240_defconfig
-
-SANDPOINT8245 BOARD
-#M: Jim Thompson <jim@musenki.com>
-S: Orphan (since 2014-04)
-F: include/configs/Sandpoint8245.h
-F: configs/Sandpoint8245_defconfig
diff --git a/board/sandpoint/Makefile b/board/sandpoint/Makefile
deleted file mode 100644
index 58f5a89..0000000
--- a/board/sandpoint/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = sandpoint.o flash.o
diff --git a/board/sandpoint/README b/board/sandpoint/README
deleted file mode 100644
index c9996a8..0000000
--- a/board/sandpoint/README
+++ /dev/null
@@ -1,411 +0,0 @@
-This port of U-Boot will run on a Motorola Sandpoint 3 development
-system equipped with a Unity X4 PPMC card (MPC8240 CPU) only. It is a
-snapshot of work in progress and far from being completed. In order
-to run it on the target system, it has to be downloaded using the
-DINK32 monitor program that came with your Sandpoint system. Please
-note that DINK32 does not accept the S-Record file created by the
-U-Boot build process unmodified, because it contains CR/LF line
-terminators. You have to strip the CR characters first. There is a
-tiny script named 'dinkdl' I created for this purpose.
-
-The Sandpoint port is based on the work of Rob Taylor, who does not
-seem to maintain it any more. I can be reached by mail as
-tkoeller at gmx.net.
-
-Thomas Koeller
-
-
-The port was tested on a Sandpoint 8240 X3 board, with U-Boot
-installed in the flash memory of the CPU card. Please use the
-following DIP switch settings:
-
-Motherboard:
-
-SW1.1: on SW1.2: on SW1.3: on SW1.4: on
-SW1.5: on SW1.6: on SW1.7: on SW1.8: on
-
-SW2.1: on SW2.2: on SW2.3: on SW2.4: on
-SW2.5: on SW2.6: on SW2.7: on SW2.8: on
-
-
-CPU Card:
-
-SW2.1: OFF SW2.2: OFF SW2.3: on SW2.4: on
-SW2.5: OFF SW2.6: OFF SW2.7: OFF SW2.8: OFF
-
-SW3.1: OFF SW3.2: on SW3.3: OFF SW3.4: OFF
-SW3.5: on SW3.6: OFF SW3.7: OFF SW3.8: on
-
-
-The followind detailed description of installation and initial steps
-with U-Boot and QNX was provided by Jim Sandoz <sandoz@lucent.com>:
-
-
-Directions for installing U-Boot on Sandpoint+Unity8240
-using the Abatron BDI2000 BDM/JTAG debugger ...
-
-Background and Reference info:
-http://u-boot.sourceforge.net/
-http://www.abatron.ch/
-http://www.abatron.ch/BDI/bdihw.html
-http://www.abatron.ch/DataSheets/BDI2000.pdf
-http://www.abatron.ch/Manuals/ManGdbCOP-2000C.pdf
-http://e-www.motorola.com/collateral/SPX3UM.pdf
-http://e-www.motorola.com/collateral/UNITYX4CONFIG.pdf
-
-
-Connection Diagram:
- ===========
- === ===== |----- |
-| | <---------------> | | | | |
-|PC | rs232 | BDI |=============[] | |
-| | |2000 | BDM probe | | |
-| | <---------------> | | |----- |
- === ethernet ===== | |
- | |
- ===========
- Sandpoint X3 with
- Unity 8240 proc
-
-
-PART 1)
- DIP Switch Settings:
-
-Sandpoint X3 8240 processor board DIP switch settings, with
-U-Boot to be installed in the flash memory of the CPU card:
-
-Motorola Sandpoint X3 Motherboard:
-SW1.1: on SW1.2: on SW1.3: on SW1.4: on
-SW1.5: on SW1.6: on SW1.7: on SW1.8: on
-SW2.1: on SW2.2: on SW2.3: on SW2.4: on
-SW2.5: on SW2.6: on SW2.7: on SW2.8: on
-
-Motorola Unity 8240 CPU Card:
-SW2.1: OFF SW2.2: OFF SW2.3: on SW2.4: on
-SW2.5: OFF SW2.6: OFF SW2.7: OFF SW2.8: OFF
-SW3.1: OFF SW3.2: on SW3.3: OFF SW3.4: OFF
-SW3.5: on SW3.6: OFF SW3.7: OFF SW3.8: on
-
-
-PART 2)
- Connect the BDI2000 Cable to the Sandpoint/Unity 8240:
-
-BDM Pin 1 on the Unity 8240 processor board is towards the
-PCI PMC connectors, or away from the socketed SDRAM, i.e.:
-
- ====================
- | ---------------- |
- | | SDRAM | |
- | | | |
- | ---------------- |
- | |~| |
- | |B| ++++++ |
- | |D| + uP + |
- | |M| +8240+ |
- | ~ 1 ++++++ |
- | |
- | |
- | |
- | PMC conn ====== |
- | ===== ====== |
- | |
- ====================
-
-
-PART 3)
- Setting up the BDI2000, and preparing for TCP/IP network comms:
-
-Connect the BDI2000 to the PC using the supplied serial cable.
-Download the BDI2000 software and install it using setup.exe.
-
-[Note: of course you can also use the Linux command line tool
-"bdisetup" to configure your BDI2000 - the sources are included on
-the floppy disk that comes with your BDI2000. Just in case you don't
-have any Windows PC's - like me :-) -- wd ]
-
-Power up the BDI2000; then follow directions to assign the IP
-address and related network information. Note that U-Boot
-will be loaded to the Sandpoint via tftp. You need to either
-use the Abatron-provided tftp application or provide a tftp
-server (e.g. Linux/Solaris/*BSD) somewhere on your network.
-Once the IP address etc are assigned via the RS232 port,
-further communication with the BDI2000 will happen via the
-ethernet connection.
-
-PART 4)
- Making a TCP/IP network connection to the Abatron BDI2000:
-
-Telnet to the Abatron BDI2000. Assuming that all of the
-networking info was loaded via RS232 correctly, you will see
-the following (scrolling):
-
-- TARGET: waiting for target Vcc
-- TARGET: waiting for target Vcc
-
-
-PART 5)
- Power up the target Sandpoint:
-If the BDM connections are correct, the following will now appear:
-
-- TARGET: waiting for target Vcc
-- TARGET: waiting for target Vcc
-- TARGET: processing power-up delay
-- TARGET: processing user reset request
-- BDI asserts HRESET
-- Reset JTAG controller passed
-- Bypass check: 0x55 => 0xAA
-- Bypass check: 0x55 => 0xAA
-- JTAG exists check passed
-- Target PVR is 0x00810101
-- COP status is 0x01
-- Check running state passed
-- BDI scans COP freeze command
-- BDI removes HRESET
-- COP status is 0x05
-- Check stopped state passed
-- Check LSRL length passed
-- BDI sets breakpoint at 0xFFF00100
-- BDI resumes program execution
-- Waiting for target stop passed
-- TARGET: Target PVR is 0x00810101
-- TARGET: reseting target passed
-- TARGET: processing target startup ....
-- TARGET: processing target startup passed
-BDI>
-
-
-PART 6)
- Erase the current contents of the flash memory:
-
-BDI>era 0xFFF00000
- Erasing flash at 0xfff00000
- Erasing flash passed
-BDI>era 0xFFF04000
- Erasing flash at 0xfff04000
- Erasing flash passed
-BDI>era 0xFFF06000
- Erasing flash at 0xfff06000
- Erasing flash passed
-BDI>era 0xFFF08000
- Erasing flash at 0xfff08000
- Erasing flash passed
-BDI>era 0xFFF10000
- Erasing flash at 0xfff10000
- Erasing flash passed
-BDI>era 0xFFF20000
- Erasing flash at 0xfff20000
- Erasing flash passed
-
-
-PART 7)
- Program the flash memory with the U-Boot image:
-
-BDI>prog 0xFFF00000 u-boot.bin bin
- Programming u-boot.bin , please wait ....
- Programming flash passed
-
-
-PART 8)
- Connect PC to Sandpoint:
-Using a crossover serial cable, attach the PC serial port to the
-Sandpoint's COM1. Set communications parameters to 8N1 / 9600 baud.
-
-
-PART 9)
- Reset the Unity and begin U-Boot execution:
-
-BDI>reset
-- TARGET: processing user reset request
-- TARGET: Target PVR is 0x00810101
-- TARGET: reseting target passed
-- TARGET: processing target init list ....
-- TARGET: processing target init list passed
-
-BDI>go
-
-Now see output from U-Boot running, sent via serial port:
-
-U-Boot 1.1.4 (Jan 23 2002 - 18:29:19)
-
-CPU: MPC8240 Revision 1.1 at 264 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: Sandpoint 8240 Unity
-DRAM: 64 MB
-FLASH: 2 MB
-PCI: scanning bus0 ...
- bus dev fn venID devID class rev MBAR0 MBAR1 IPIN ILINE
- 00 00 00 1057 0003 060000 13 00000008 00000000 01 00
- 00 0b 00 10ad 0565 060100 10 00000000 00000000 00 00
- 00 0f 00 8086 1229 020000 08 80000000 80000001 01 00
-In: serial
-Out: serial
-Err: serial
-=>
-
-
-PART 10)
- Set and save any required environmental variables, examples of some:
-
-=> setenv ethaddr 00:03:47:97:D0:79
-=> setenv bootfile your_qnx_image_here
-=> setenv hostname sandpointX
-=> setenv netmask 255.255.255.0
-=> setenv ipaddr 192.168.0.11
-=> setenv serverip 192.168.0.10
-=> setenv gatewayip=192.168.0.1
-=> saveenv
-Saving Environment to Flash...
-Un-Protected 1 sectors
-Erasing Flash...
- done
-Erased 1 sectors
-Writing to Flash... done
-Protected 1 sectors
-=>
-
-**** Example environment: ****
-
-=> printenv
-baudrate=9600
-bootfile=telemetry
-hostname=sp1
-ethaddr=00:03:47:97:E4:6B
-load=tftp 100000 u-boot.bin
-update=protect off all;era FFF00000 FFF3FFFF;cp.b 100000 FFF00000 ${filesize};saveenv
-filesize=1f304
-gatewayip=145.17.228.1
-netmask=255.255.255.0
-ipaddr=145.17.228.42
-serverip=145.17.242.46
-stdin=serial
-stdout=serial
-stderr=serial
-
-Environment size: 332/8188 bytes
-=>
-
-here's some text useful stuff for cut-n-paste:
-setenv hostname sandpoint1
-setenv netmask 255.255.255.0
-setenv ipaddr 145.17.228.81
-setenv serverip 145.17.242.46
-setenv gatewayip 145.17.228.1
-saveenv
-
-PART 11)
- Test U-Boot by tftp'ing new U-Boot, overwriting current:
-
-=> protect off all
-Un-Protect Flash Bank # 1
-=> tftp 100000 u-boot.bin
-eth: Intel i82559 PCI EtherExpressPro @0x80000000(bus=0, device=15, func=0)
-ARP broadcast 1
-TFTP from server 145.17.242.46; our IP address is 145.17.228.42; sending through
- gateway 145.17.228.1
-Filename 'u-boot.bin'.
-Load address: 0x100000
-Loading: #########################
-done
-Bytes transferred = 127628 (1f28c hex)
-=> era all
-Erase Flash Bank # 1
- done
-Erase Flash Bank # 2 - missing
-=> cp.b 0x100000 FFF00000 1f28c
-Copy to Flash... done
-=> saveenv
-Saving Environment to Flash...
-Un-Protected 1 sectors
-Erasing Flash...
- done
-Erased 1 sectors
-Writing to Flash... done
-Protected 1 sectors
-=> reset
-
-You can put these commands into some environment variables;
-
-=> setenv load tftp 100000 u-boot.bin
-=> setenv update protect off all\;era FFF00000 FFF3FFFF\;cp.b 100000 FFF00000 \${filesize}\;saveenv
-=> saveenv
-
-Then you just have to type "run load" then "run update"
-
-=> run load
-eth: Intel i82559 PCI EtherExpressPro @0x80000000(bus=0, device=15, func=0)
-ARP broadcast 1
-TFTP from server 145.17.242.46; our IP address is 145.17.228.42; sending through
- gateway 145.17.228.1
-Filename 'u-boot.bin'.
-Load address: 0x100000
-Loading: #########################
-done
-Bytes transferred = 127748 (1f304 hex)
-=> run update
-Un-Protect Flash Bank # 1
-Un-Protect Flash Bank # 2
-Erase Flash from 0xfff00000 to 0xfff3ffff
- done
-Erased 7 sectors
-Copy to Flash... done
-Saving Environment to Flash...
-Un-Protected 1 sectors
-Erasing Flash...
- done
-Erased 1 sectors
-Writing to Flash... done
-Protected 1 sectors
-=>
-
-
-PART 12)
- Load OS image (ELF format) via U-Boot using tftp
-
-
-=> tftp 800000 sandpoint-simple.elf
-eth: Intel i82559 PCI EtherExpressPro @0x80000000(bus=0, device=15, func=0)
-ARP broadcast 1
-TFTP from server 145.17.242.46; our IP address is 145.17.228.42; sending through
- gateway 145.17.228.1
-Filename 'sandpoint-simple.elf'.
-Load address: 0x800000
-Loading: #################################################################
- #################################################################
- #################################################################
- ########################
-done
-Bytes transferred = 1120284 (11181c hex)
-==>
-
-PART 13)
- Begin OS image execution: (note that unless you have the
-serial parameters of your OS image set to 9600 (i.e. same as
-the U-Boot binary) you will get garbage here until you change
-the serial communications speed.
-
-=> bootelf 800000
-Loading @ 0x001f0100 (1120028 bytes)
-## Starting application at 0x001f1d28 ...
-Replace init_hwinfo() with a board specific version
-
-Loading QNX6....
-
-Header size=0x0000009c, Total Size=0x000005c0, #Cpu=1, Type=1
-<...loader and kernel messages snipped...>
-
-Welcome to Neutrino on the Sandpoint
-#
-
-
-other information:
-
-CVS Retrieval Notes:
-
-U-Boot's SourceForge CVS repository can be checked out
-through anonymous (pserver) CVS with the following
-instruction set. The module you wish to check out must
-be specified as the modulename. When prompted for a
-password for anonymous, simply press the Enter key.
-
-cvs -d:pserver:anonymous at cvs.u-boot.sourceforge.net:/cvsroot/u-boot login
-
-cvs -z6 -d:pserver:anonymous at cvs.u-boot.sourceforge.net:/cvsroot/u-boot co -P u-boot
diff --git a/board/sandpoint/dinkdl b/board/sandpoint/dinkdl
deleted file mode 100644
index f281452..0000000
--- a/board/sandpoint/dinkdl
+++ /dev/null
@@ -1,2 +0,0 @@
-#! /bin/bash
-tr -d "\r" <$1 >/dev/tts/1
diff --git a/board/sandpoint/flash.c b/board/sandpoint/flash.c
deleted file mode 100644
index 1ab668c..0000000
--- a/board/sandpoint/flash.c
+++ /dev/null
@@ -1,748 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/pci_io.h>
-#include <w83c553f.h>
-
-#define ROM_CS0_START 0xFF800000
-#define ROM_CS1_START 0xFF000000
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-#if 0
-static void flash_get_offsets (ulong base, flash_info_t *info);
-#endif /* 0 */
-
-/*flash command address offsets*/
-
-#if 0
-#define ADDR0 (0x555)
-#define ADDR1 (0x2AA)
-#define ADDR3 (0x001)
-#else
-#define ADDR0 (0xAAA)
-#define ADDR1 (0x555)
-#define ADDR3 (0x001)
-#endif
-
-#define FLASH_WORD_SIZE unsigned char
-
-/*-----------------------------------------------------------------------
- */
-
-#if 0
-static int byte_parity_odd(unsigned char x) __attribute__ ((const));
-#endif /* 0 */
-static unsigned long flash_id(unsigned char mfct, unsigned char chip) __attribute__ ((const));
-
-typedef struct
-{
- FLASH_WORD_SIZE extval;
- unsigned short intval;
-} map_entry;
-
-#if 0
-static int
-byte_parity_odd(unsigned char x)
-{
- x ^= x >> 4;
- x ^= x >> 2;
- x ^= x >> 1;
- return (x & 0x1) != 0;
-}
-#endif /* 0 */
-
-
-static unsigned long
-flash_id(unsigned char mfct, unsigned char chip)
-{
- static const map_entry mfct_map[] =
- {
- {(FLASH_WORD_SIZE) AMD_MANUFACT, (unsigned short) ((unsigned long) FLASH_MAN_AMD >> 16)},
- {(FLASH_WORD_SIZE) FUJ_MANUFACT, (unsigned short) ((unsigned long) FLASH_MAN_FUJ >> 16)},
- {(FLASH_WORD_SIZE) STM_MANUFACT, (unsigned short) ((unsigned long) FLASH_MAN_STM >> 16)},
- {(FLASH_WORD_SIZE) MT_MANUFACT, (unsigned short) ((unsigned long) FLASH_MAN_MT >> 16)},
- {(FLASH_WORD_SIZE) INTEL_MANUFACT,(unsigned short) ((unsigned long) FLASH_MAN_INTEL >> 16)},
- {(FLASH_WORD_SIZE) INTEL_ALT_MANU,(unsigned short) ((unsigned long) FLASH_MAN_INTEL >> 16)}
- };
-
- static const map_entry chip_map[] =
- {
- {AMD_ID_F040B, FLASH_AM040},
- {(FLASH_WORD_SIZE) STM_ID_x800AB, FLASH_STM800AB}
- };
-
- const map_entry *p;
- unsigned long result = FLASH_UNKNOWN;
-
- /* find chip id */
- for(p = &chip_map[0]; p < &chip_map[sizeof chip_map / sizeof chip_map[0]]; p++)
- if(p->extval == chip)
- {
- result = FLASH_VENDMASK | p->intval;
- break;
- }
-
- /* find vendor id */
- for(p = &mfct_map[0]; p < &mfct_map[sizeof mfct_map / sizeof mfct_map[0]]; p++)
- if(p->extval == mfct)
- {
- result &= ~FLASH_VENDMASK;
- result |= (unsigned long) p->intval << 16;
- break;
- }
-
- return result;
-}
-
-
-unsigned long
-flash_init(void)
-{
- unsigned long i;
- unsigned char j;
- static const ulong flash_banks[] = CONFIG_SYS_FLASH_BANKS;
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
- {
- flash_info_t * const pflinfo = &flash_info[i];
- pflinfo->flash_id = FLASH_UNKNOWN;
- pflinfo->size = 0;
- pflinfo->sector_count = 0;
- }
-
- /* Enable writes to Sandpoint flash */
- {
- register unsigned char temp;
- CONFIG_READ_BYTE(CONFIG_SYS_WINBOND_ISA_CFG_ADDR + WINBOND_CSCR, temp);
- temp &= ~0x20; /* clear BIOSWP bit */
- CONFIG_WRITE_BYTE(CONFIG_SYS_WINBOND_ISA_CFG_ADDR + WINBOND_CSCR, temp);
- }
-
- for(i = 0; i < sizeof flash_banks / sizeof flash_banks[0]; i++)
- {
- flash_info_t * const pflinfo = &flash_info[i];
- const unsigned long base_address = flash_banks[i];
- volatile FLASH_WORD_SIZE * const flash = (FLASH_WORD_SIZE *) base_address;
-#if 0
- volatile FLASH_WORD_SIZE * addr2;
-#endif
-#if 0
- /* write autoselect sequence */
- flash[0x5555] = 0xaa;
- flash[0x2aaa] = 0x55;
- flash[0x5555] = 0x90;
-#else
- flash[0xAAA << (3 * i)] = 0xaa;
- flash[0x555 << (3 * i)] = 0x55;
- flash[0xAAA << (3 * i)] = 0x90;
-#endif
- __asm__ __volatile__("sync");
-
-#if 0
- pflinfo->flash_id = flash_id(flash[0x0], flash[0x1]);
-#else
- pflinfo->flash_id = flash_id(flash[0x0], flash[0x2 + 14 * i]);
-#endif
-
- switch(pflinfo->flash_id & FLASH_TYPEMASK)
- {
- case FLASH_AM040:
- pflinfo->size = 0x00080000;
- pflinfo->sector_count = 8;
- for(j = 0; j < 8; j++)
- {
- pflinfo->start[j] = base_address + 0x00010000 * j;
- pflinfo->protect[j] = flash[(j << 16) | 0x2];
- }
- break;
- case FLASH_STM800AB:
- pflinfo->size = 0x00100000;
- pflinfo->sector_count = 19;
- pflinfo->start[0] = base_address;
- pflinfo->start[1] = base_address + 0x4000;
- pflinfo->start[2] = base_address + 0x6000;
- pflinfo->start[3] = base_address + 0x8000;
- for(j = 1; j < 16; j++)
- {
- pflinfo->start[j+3] = base_address + 0x00010000 * j;
- }
-#if 0
- /* check for protected sectors */
- for (j = 0; j < pflinfo->sector_count; j++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr2 = (volatile FLASH_WORD_SIZE *)(pflinfo->start[j]);
- if (pflinfo->flash_id & FLASH_MAN_SST)
- pflinfo->protect[j] = 0;
- else
- pflinfo->protect[j] = addr2[2] & 1;
- }
-#endif
- break;
- }
- /* Protect monitor and environment sectors
- */
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[0]);
-#endif
-
- /* reset device to read mode */
- flash[0x0000] = 0xf0;
- __asm__ __volatile__("sync");
- }
-
- return flash_info[0].size + flash_info[1].size;
-}
-
-#if 0
-static void
-flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- /* set up sector start address table */
- if (info->flash_id & FLASH_MAN_SST)
- {
- for (i = 0; i < info->sector_count; i++)
- info->start[i] = base + (i * 0x00010000);
- }
- else
- if (info->flash_id & FLASH_BTYPE) {
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00004000;
- info->start[2] = base + 0x00006000;
- info->start[3] = base + 0x00008000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00010000) - 0x00030000;
- }
- } else {
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00004000;
- info->start[i--] = base + info->size - 0x00006000;
- info->start[i--] = base + info->size - 0x00008000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00010000;
- }
- }
-
-}
-#endif /* 0 */
-
-/*-----------------------------------------------------------------------
- */
-void
-flash_print_info(flash_info_t *info)
-{
- static const char unk[] = "Unknown";
- const char *mfct = unk, *type = unk;
- unsigned int i;
-
- if(info->flash_id != FLASH_UNKNOWN)
- {
- switch(info->flash_id & FLASH_VENDMASK)
- {
- case FLASH_MAN_AMD: mfct = "AMD"; break;
- case FLASH_MAN_FUJ: mfct = "FUJITSU"; break;
- case FLASH_MAN_STM: mfct = "STM"; break;
- case FLASH_MAN_SST: mfct = "SST"; break;
- case FLASH_MAN_BM: mfct = "Bright Microelectonics"; break;
- case FLASH_MAN_INTEL: mfct = "Intel"; break;
- }
-
- switch(info->flash_id & FLASH_TYPEMASK)
- {
- case FLASH_AM040: type = "AM29F040B (512K * 8, uniform sector size)"; break;
- case FLASH_AM400B: type = "AM29LV400B (4 Mbit, bottom boot sect)"; break;
- case FLASH_AM400T: type = "AM29LV400T (4 Mbit, top boot sector)"; break;
- case FLASH_AM800B: type = "AM29LV800B (8 Mbit, bottom boot sect)"; break;
- case FLASH_AM800T: type = "AM29LV800T (8 Mbit, top boot sector)"; break;
- case FLASH_AM160T: type = "AM29LV160T (16 Mbit, top boot sector)"; break;
- case FLASH_AM320B: type = "AM29LV320B (32 Mbit, bottom boot sect)"; break;
- case FLASH_AM320T: type = "AM29LV320T (32 Mbit, top boot sector)"; break;
- case FLASH_STM800AB: type = "M29W800AB (8 Mbit, bottom boot sect)"; break;
- case FLASH_SST800A: type = "SST39LF/VF800 (8 Mbit, uniform sector size)"; break;
- case FLASH_SST160A: type = "SST39LF/VF160 (16 Mbit, uniform sector size)"; break;
- }
- }
-
- printf(
- "\n Brand: %s Type: %s\n"
- " Size: %lu KB in %d Sectors\n",
- mfct,
- type,
- info->size >> 10,
- info->sector_count
- );
-
- printf (" Sector Start Addresses:");
-
- for (i = 0; i < info->sector_count; i++)
- {
- unsigned long size;
- unsigned int erased;
- unsigned long * flash = (unsigned long *) info->start[i];
-
- /*
- * Check if whole sector is erased
- */
- size =
- (i != (info->sector_count - 1)) ?
- (info->start[i + 1] - info->start[i]) >> 2 :
- (info->start[0] + info->size - info->start[i]) >> 2;
-
- for(
- flash = (unsigned long *) info->start[i], erased = 1;
- (flash != (unsigned long *) info->start[i] + size) && erased;
- flash++
- )
- erased = *flash == ~0x0UL;
-
- printf(
- "%s %08lX %s %s",
- (i % 5) ? "" : "\n ",
- info->start[i],
- erased ? "E" : " ",
- info->protect[i] ? "RO" : " "
- );
- }
-
- puts("\n");
- return;
-}
-
-#if 0
-
-/*
- * The following code cannot be run from FLASH!
- */
-ulong
-flash_get_size (vu_long *addr, flash_info_t *info)
-{
- short i;
- FLASH_WORD_SIZE value;
- ulong base = (ulong)addr;
- volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)addr;
-
- printf("flash_get_size: \n");
- /* Write auto select command: read Manufacturer ID */
- eieio();
- addr2[ADDR0] = (FLASH_WORD_SIZE)0xAA;
- addr2[ADDR1] = (FLASH_WORD_SIZE)0x55;
- addr2[ADDR0] = (FLASH_WORD_SIZE)0x90;
- value = addr2[0];
-
- switch (value) {
- case (FLASH_WORD_SIZE)AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
- case (FLASH_WORD_SIZE)FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case (FLASH_WORD_SIZE)SST_MANUFACT:
- info->flash_id = FLASH_MAN_SST;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
- printf("recognised manufacturer");
-
- value = addr2[ADDR3]; /* device ID */
- debug ("\ndev_code=%x\n", value);
-
- switch (value) {
- case (FLASH_WORD_SIZE)AMD_ID_LV400T:
- info->flash_id += FLASH_AM400T;
- info->sector_count = 11;
- info->size = 0x00080000;
- break; /* => 0.5 MB */
-
- case (FLASH_WORD_SIZE)AMD_ID_LV400B:
- info->flash_id += FLASH_AM400B;
- info->sector_count = 11;
- info->size = 0x00080000;
- break; /* => 0.5 MB */
-
- case (FLASH_WORD_SIZE)AMD_ID_LV800T:
- info->flash_id += FLASH_AM800T;
- info->sector_count = 19;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case (FLASH_WORD_SIZE)AMD_ID_LV800B:
- info->flash_id += FLASH_AM800B;
- info->sector_count = 19;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case (FLASH_WORD_SIZE)AMD_ID_LV160T:
- info->flash_id += FLASH_AM160T;
- info->sector_count = 35;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case (FLASH_WORD_SIZE)AMD_ID_LV160B:
- info->flash_id += FLASH_AM160B;
- info->sector_count = 35;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case (FLASH_WORD_SIZE)SST_ID_xF800A:
- info->flash_id += FLASH_SST800A;
- info->sector_count = 16;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case (FLASH_WORD_SIZE)SST_ID_xF160A:
- info->flash_id += FLASH_SST160A;
- info->sector_count = 32;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case (FLASH_WORD_SIZE)AMD_ID_F040B:
- info->flash_id += FLASH_AM040;
- info->sector_count = 8;
- info->size = 0x00080000;
- break; /* => 0.5 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
-
- }
-
- printf("flash id %lx; sector count %x, size %lx\n", info->flash_id,info->sector_count,info->size);
- /* set up sector start address table */
- if (info->flash_id & FLASH_MAN_SST)
- {
- for (i = 0; i < info->sector_count; i++)
- info->start[i] = base + (i * 0x00010000);
- }
- else
- if (info->flash_id & FLASH_BTYPE) {
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00004000;
- info->start[2] = base + 0x00006000;
- info->start[3] = base + 0x00008000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00010000) - 0x00030000;
- }
- } else {
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00004000;
- info->start[i--] = base + info->size - 0x00006000;
- info->start[i--] = base + info->size - 0x00008000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00010000;
- }
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr2 = (volatile FLASH_WORD_SIZE *)(info->start[i]);
- if (info->flash_id & FLASH_MAN_SST)
- info->protect[i] = 0;
- else
- info->protect[i] = addr2[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr2 = (FLASH_WORD_SIZE *)info->start[0];
- *addr2 = (FLASH_WORD_SIZE)0x00F000F0; /* reset bank */
- }
-
- return (info->size);
-}
-
-#endif
-
-
-int
-flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
- unsigned char sh8b;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP))) {
- printf ("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Check the ROM CS */
- if ((info->start[0] >= ROM_CS1_START) && (info->start[0] < ROM_CS0_START))
- sh8b = 3;
- else
- sh8b = 0;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00800080;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055;
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (FLASH_WORD_SIZE *)(info->start[0] + (
- (info->start[sect] - info->start[0]) << sh8b));
- if (info->flash_id & FLASH_MAN_SST)
- {
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00800080;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055;
- addr[0] = (FLASH_WORD_SIZE)0x00500050; /* block erase */
- udelay(30000); /* wait 30 ms */
- }
- else
- addr[0] = (FLASH_WORD_SIZE)0x00300030; /* sector erase */
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait@least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (FLASH_WORD_SIZE *)(info->start[0] + (
- (info->start[l_sect] - info->start[0]) << sh8b));
- while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
-DONE:
- /* reset to read mode */
- addr = (FLASH_WORD_SIZE *)info->start[0];
- addr[0] = (FLASH_WORD_SIZE)0x00F000F0; /* reset bank */
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)info->start[0];
- volatile FLASH_WORD_SIZE *dest2;
- volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *)&data;
- ulong start;
- int flag;
- int i;
- unsigned char sh8b;
-
- /* Check the ROM CS */
- if ((info->start[0] >= ROM_CS1_START) && (info->start[0] < ROM_CS0_START))
- sh8b = 3;
- else
- sh8b = 0;
-
- dest2 = (FLASH_WORD_SIZE *)(((dest - info->start[0]) << sh8b) +
- info->start[0]);
-
- /* Check if Flash is (sufficiently) erased */
- if ((*dest2 & (FLASH_WORD_SIZE)data) != (FLASH_WORD_SIZE)data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- for (i=0; i<4/sizeof(FLASH_WORD_SIZE); i++)
- {
- addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA;
- addr2[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055;
- addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00A000A0;
-
- dest2[i << sh8b] = data2[i];
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((dest2[i << sh8b] & (FLASH_WORD_SIZE)0x00800080) !=
- (data2[i] & (FLASH_WORD_SIZE)0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- }
-
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/sandpoint/sandpoint.c b/board/sandpoint/sandpoint.c
deleted file mode 100644
index 16237bd..0000000
--- a/board/sandpoint/sandpoint.c
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * (C) Copyright 2000
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <pci.h>
-#include <netdev.h>
-
-int checkboard (void)
-{
- /*TODO: Check processor type */
-
- puts ( "Board: Sandpoint "
-#ifdef CONFIG_MPC8240
- "8240"
-#endif
-#ifdef CONFIG_MPC8245
- "8245"
-#endif
- " Unity ##Test not implemented yet##\n");
- return 0;
-}
-
-#if 0 /* NOT USED */
-int checkflash (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("## Test not implemented yet ##\n");
-
- return (0);
-}
-#endif
-
-phys_size_t initdram (int board_type)
-{
- long size;
- long new_bank0_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-/*
- * Initialize PCI Devices, report devices found.
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_sandpoint_config_table[] = {
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x10, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET1_IOADDR,
- PCI_ENET1_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { }
-};
-#endif
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_sandpoint_config_table,
-#endif
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/board/sandpoint/u-boot.lds b/board/sandpoint/u-boot.lds
deleted file mode 100644
index cd9f07c..0000000
--- a/board/sandpoint/u-boot.lds
+++ /dev/null
@@ -1,84 +0,0 @@
-/*
- * (C) Copyright 2001-2007
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc824x/start.o (.text*)
- *(.text.v*printf)
-
- . = DEFINED(env_offset) ? env_offset : .;
- common/env_embedded.o (.ppcenv*)
-
- *(.text*)
- . = ALIGN(16);
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/board/utx8245/Kconfig b/board/utx8245/Kconfig
deleted file mode 100644
index aec0eb9..0000000
--- a/board/utx8245/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_UTX8245
-
-config SYS_BOARD
- default "utx8245"
-
-config SYS_CONFIG_NAME
- default "utx8245"
-
-endif
diff --git a/board/utx8245/MAINTAINERS b/board/utx8245/MAINTAINERS
deleted file mode 100644
index bed69c8..0000000
--- a/board/utx8245/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-UTX8245 BOARD
-M: Greg Allen <gallen@arlut.utexas.edu>
-S: Maintained
-F: board/utx8245/
-F: include/configs/utx8245.h
-F: configs/utx8245_defconfig
diff --git a/board/utx8245/Makefile b/board/utx8245/Makefile
deleted file mode 100644
index f12e545..0000000
--- a/board/utx8245/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2002
-# Gregory E. Allen, gallen at arlut.utexas.edu
-# Matthew E. Karger, karger at arlut.utexas.edu
-# Applied Research Laboratories, The University of Texas at Austin
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = utx8245.o flash.o
diff --git a/board/utx8245/flash.c b/board/utx8245/flash.c
deleted file mode 100644
index 1dfcb41..0000000
--- a/board/utx8245/flash.c
+++ /dev/null
@@ -1,544 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * Gregory E. Allen, gallen at arlut.utexas.edu
- * Matthew E. Karger, karger at arlut.utexas.edu
- * Applied Research Laboratories, The University of Texas at Austin
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-
-#define ROM_CS0_START 0xFF800000
-#define ROM_CS1_START 0xFF000000
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-#define FLASH_BANK_SIZE ((uint)(16 * 1024 * 1024)) /* max 16Mbyte */
-#define MAIN_SECT_SIZE 0x10000
-#define SECT_SIZE_32KB 0x8000
-#define SECT_SIZE_8KB 0x2000
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-static int write_word (flash_info_t * info, ulong dest, ulong data);
-#if 0
-static void write_via_fpu (vu_long * addr, ulong * data);
-#endif
-static __inline__ unsigned long get_msr (void);
-static __inline__ void set_msr (unsigned long msr);
-
-/*flash command address offsets*/
-#define ADDR0 (0x555)
-#define ADDR1 (0xAAA)
-#define ADDR3 (0x001)
-
-#define FLASH_WORD_SIZE unsigned char
-
-/*---------------------------------------------------------------------*/
-/*#define DEBUG_FLASH 1 */
-
-/*---------------------------------------------------------------------*/
-
-unsigned long flash_init (void)
-{
- int i; /* flash bank counter */
- int j; /* flash device sector counter */
- int k; /* flash size calculation loop counter */
- int N; /* pow(2,N) is flash size, but we don't have <math.h> */
- ulong total_size = 0, device_size = 1;
- unsigned char manuf_id, device_id;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- vu_char *addr = (vu_char *) (CONFIG_SYS_FLASH_BASE + i * FLASH_BANK_SIZE);
-
- addr[0x555] = 0xAA; /* get manuf/device info command */
- addr[0x2AA] = 0x55; /* 3-cycle command */
- addr[0x555] = 0x90;
-
- manuf_id = addr[0]; /* read back manuf/device info */
- device_id = addr[1];
-
- addr[0x55] = 0x98; /* CFI command */
- N = addr[0x27]; /* read back device_size = pow(2,N) */
-
- for (k = 0; k < N; k++) /* calculate device_size = pow(2,N) */
- device_size *= 2;
-
- flash_info[i].size = device_size;
- flash_info[i].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-
-#if defined DEBUG_FLASH
- printf ("manuf_id = %x, device_id = %x\n", manuf_id, device_id);
-#endif
- /* find out what kind of flash we are using */
- if ((manuf_id == (uchar) (AMD_MANUFACT))
- && (device_id == AMD_ID_LV033C)) {
- flash_info[i].flash_id =
- ((FLASH_MAN_AMD & FLASH_VENDMASK) << 16) |
- (FLASH_AM033C & FLASH_TYPEMASK);
-
- /* set individual sector start addresses */
- for (j = 0; j < flash_info[i].sector_count; j++) {
- flash_info[i].start[j] =
- (CONFIG_SYS_FLASH_BASE + i * FLASH_BANK_SIZE +
- j * MAIN_SECT_SIZE);
- }
- }
-
- else if ((manuf_id == (uchar) (AMD_MANUFACT)) &&
- (device_id == AMD_ID_LV116DT)) {
- flash_info[i].flash_id =
- ((FLASH_MAN_AMD & FLASH_VENDMASK) << 16) |
- (FLASH_AM160T & FLASH_TYPEMASK);
-
- /* set individual sector start addresses */
- for (j = 0; j < flash_info[i].sector_count; j++) {
- flash_info[i].start[j] =
- (CONFIG_SYS_FLASH_BASE + i * FLASH_BANK_SIZE +
- j * MAIN_SECT_SIZE);
-
- if (j < (CONFIG_SYS_MAX_FLASH_SECT - 3)) {
- flash_info[i].start[j] =
- (CONFIG_SYS_FLASH_BASE + i * FLASH_BANK_SIZE +
- j * MAIN_SECT_SIZE);
- } else if (j == (CONFIG_SYS_MAX_FLASH_SECT - 3)) {
- flash_info[i].start[j] =
- (flash_info[i].start[j - 1] + SECT_SIZE_32KB);
-
- } else {
- flash_info[i].start[j] =
- (flash_info[i].start[j - 1] + SECT_SIZE_8KB);
- }
- }
- }
-
- else {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- addr[0] = 0xFF;
- goto Done;
- }
-
-#if defined DEBUG_FLASH
- printf ("flash_id = 0x%08lX\n", flash_info[i].flash_id);
-#endif
-
- addr[0] = 0xFF;
-
- memset (flash_info[i].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
-
- total_size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- flash_protect (FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
- flash_protect (FLAG_PROTECT_SET, CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-#endif
-
- Done:
- return total_size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- static const char unk[] = "Unknown";
- const char *mfct = unk, *type = unk;
- unsigned int i;
-
- if (info->flash_id != FLASH_UNKNOWN) {
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- mfct = "AMD";
- break;
- case FLASH_MAN_FUJ:
- mfct = "FUJITSU";
- break;
- case FLASH_MAN_STM:
- mfct = "STM";
- break;
- case FLASH_MAN_SST:
- mfct = "SST";
- break;
- case FLASH_MAN_BM:
- mfct = "Bright Microelectonics";
- break;
- case FLASH_MAN_INTEL:
- mfct = "Intel";
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM033C:
- type = "AM29LV033C (32 Mbit, uniform sector size)";
- break;
- case FLASH_AM160T:
- type = "AM29LV160T (16 Mbit, top boot sector)";
- break;
- case FLASH_AM040:
- type = "AM29F040B (512K * 8, uniform sector size)";
- break;
- case FLASH_AM400B:
- type = "AM29LV400B (4 Mbit, bottom boot sect)";
- break;
- case FLASH_AM400T:
- type = "AM29LV400T (4 Mbit, top boot sector)";
- break;
- case FLASH_AM800B:
- type = "AM29LV800B (8 Mbit, bottom boot sect)";
- break;
- case FLASH_AM800T:
- type = "AM29LV800T (8 Mbit, top boot sector)";
- break;
- case FLASH_AM320B:
- type = "AM29LV320B (32 Mbit, bottom boot sect)";
- break;
- case FLASH_AM320T:
- type = "AM29LV320T (32 Mbit, top boot sector)";
- break;
- case FLASH_STM800AB:
- type = "M29W800AB (8 Mbit, bottom boot sect)";
- break;
- case FLASH_SST800A:
- type = "SST39LF/VF800 (8 Mbit, uniform sector size)";
- break;
- case FLASH_SST160A:
- type = "SST39LF/VF160 (16 Mbit, uniform sector size)";
- break;
- }
- }
-
- printf ("\n Brand: %s Type: %s\n"
- " Size: %lu KB in %d Sectors\n",
- mfct, type, info->size >> 10, info->sector_count);
-
- printf (" Sector Start Addresses:");
-
- for (i = 0; i < info->sector_count; i++) {
- unsigned long size;
- unsigned int erased;
- unsigned long *flash = (unsigned long *) info->start[i];
-
- /*
- * Check if whole sector is erased
- */
- size = (i != (info->sector_count - 1)) ?
- (info->start[i + 1] - info->start[i]) >> 2 :
- (info->start[0] + info->size - info->start[i]) >> 2;
-
- for (flash = (unsigned long *) info->start[i], erased = 1;
- (flash != (unsigned long *) info->start[i] + size) && erased;
- flash++)
- erased = *flash == ~0x0UL;
-
- printf ("%s %08lX %s %s",
- (i % 5) ? "" : "\n ",
- info->start[i],
- erased ? "E" : " ", info->protect[i] ? "RO" : " ");
- }
-
- puts ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
- unsigned char sh8b;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP))) {
- printf ("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Check the ROM CS */
- if ((info->start[0] >= ROM_CS1_START)
- && (info->start[0] < ROM_CS0_START))
- sh8b = 3;
- else
- sh8b = 0;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00800080;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (FLASH_WORD_SIZE *) (info->start[0] + ((info->
- start[sect] -
- info->
- start[0]) <<
- sh8b));
-
- if (info->flash_id & FLASH_MAN_SST) {
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00800080;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
- addr[0] = (FLASH_WORD_SIZE) 0x00500050; /* block erase */
- udelay (30000); /* wait 30 ms */
- } else {
- addr[0] = (FLASH_WORD_SIZE) 0x00300030; /* sector erase */
- }
-
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* wait@least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (FLASH_WORD_SIZE *) (info->start[0] + ((info->start[l_sect] -
- info->
- start[0]) << sh8b));
- while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) !=
- (FLASH_WORD_SIZE) 0x00800080) {
- if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
- DONE:
- /* reset to read mode */
- addr = (FLASH_WORD_SIZE *) info->start[0];
- addr[0] = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */
-
- printf (" done\n");
- return 0;
-}
-
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < 4 && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_word (info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i = 0; i < 4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word (info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_word (info, wp, data));
-}
-
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t * info, ulong dest, ulong data)
-{
- volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) info->start[0];
- volatile FLASH_WORD_SIZE *dest2;
- volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data;
- ulong start;
- int flag;
- int i;
- unsigned char sh8b;
-
- /* Check the ROM CS */
- if ((info->start[0] >= ROM_CS1_START)
- && (info->start[0] < ROM_CS0_START))
- sh8b = 3;
- else
- sh8b = 0;
-
- dest2 = (FLASH_WORD_SIZE *) (((dest - info->start[0]) << sh8b) +
- info->start[0]);
-
- /* Check if Flash is (sufficiently) erased */
- if ((*dest2 & (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) {
- addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr2[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
- addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00A000A0;
-
- dest2[i << sh8b] = data2[i];
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((dest2[i << sh8b] & (FLASH_WORD_SIZE) 0x00800080) !=
- (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- }
-
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
-#if 0
-static void write_via_fpu (vu_long * addr, ulong * data)
-{
- __asm__ __volatile__ ("lfd 1, 0(%0)"::"r" (data));
- __asm__ __volatile__ ("stfd 1, 0(%0)"::"r" (addr));
-}
-#endif
-
-/*-----------------------------------------------------------------------
- */
-static __inline__ unsigned long get_msr (void)
-{
- unsigned long msr;
-
- __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
-
- return msr;
-}
-
-static __inline__ void set_msr (unsigned long msr)
-{
- __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
-}
diff --git a/board/utx8245/utx8245.c b/board/utx8245/utx8245.c
deleted file mode 100644
index 69d19e3..0000000
--- a/board/utx8245/utx8245.c
+++ /dev/null
@@ -1,119 +0,0 @@
-/*
- * (C) Copyright 2001
- * Rob Taylor, Flying Pig Systems. robt at flyingpig.com.
- *
- * (C) Copyright 2002
- * Gregory E. Allen, gallen at arlut.utexas.edu
- * Matthew E. Karger, karger at arlut.utexas.edu
- * Applied Research Laboratories, The University of Texas at Austin
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/mmu.h>
-#include <pci.h>
-#include <netdev.h>
-
-#define SAVE_SZ 32
-
-
-int checkboard(void)
-{
- ulong busfreq = get_bus_freq(0);
- char buf[32];
-
- printf("Board: UTX8245 Local Bus at %s MHz\n", strmhz(buf, busfreq));
- return 0;
-}
-
-
-phys_size_t initdram(int board_type)
-{
- long size;
- long new_bank0_end;
- long new_bank1_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size/2 - 1;
- new_bank1_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
-
- mear1 = (mear1 & 0xFFFF0000) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) |
- ((new_bank1_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT << 8);
- emear1 = (emear1 & 0xFFFF0000) |
- ((new_bank0_end & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
- ((new_bank1_end & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT << 8);
-
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-
-/*
- * Initialize PCI Devices, report devices found.
- */
-
-static struct pci_config_table pci_utx8245_config_table[] = {
-#ifndef CONFIG_PCI_PNP
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0C, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0B, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_FIREWIRE_IOADDR,
- PCI_FIREWIRE_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
-#endif /*CONFIG_PCI_PNP*/
- { }
-};
-
-
-static void pci_utx8245_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
-{
- if (PCI_DEV(dev) == 11)
- /* assign serial interrupt line 9 (int25) to FireWire */
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, 25);
-
- else if (PCI_DEV(dev) == 12)
- /* assign serial interrupt line 8 (int24) to Ethernet */
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, 24);
-
- else if (PCI_DEV(dev) == 14)
- /* assign serial interrupt line 0 (int16) to PMC slot 0 */
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, 16);
-
- else if (PCI_DEV(dev) == 15)
- /* assign serial interrupt line 1 (int17) to PMC slot 1 */
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, 17);
-}
-
-static struct pci_controller utx8245_hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_utx8245_config_table,
- fixup_irq: pci_utx8245_fixup_irq,
- write_byte: pci_hose_write_config_byte
-#endif /*CONFIG_PCI_PNP*/
-};
-
-void pci_init_board (void)
-{
- pci_mpc824x_init(&utx8245_hose);
-
- icache_enable();
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c
index ddc24be..682d18f 100644
--- a/common/cmd_pcmcia.c
+++ b/common/cmd_pcmcia.c
@@ -331,11 +331,8 @@ int check_ide_device (int slot)
ide_devices_found |= (1 << slot);
-#if CONFIG_CPC45
-#else
/* set I/O area in config reg -> only valid for ARGOSY D5!!! */
*((uchar *)(addr + config_base)) = 1;
-#endif
#if 0
printf("\n## Config_base = %04x ###\n", config_base);
printf("Configuration Option Register: %02x @ %x\n", readb(addr + config_base), addr + config_base);
diff --git a/configs/A3000_defconfig b/configs/A3000_defconfig
deleted file mode 100644
index e1923de..0000000
--- a/configs/A3000_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_A3000=y
diff --git a/configs/CPC45_ROMBOOT_defconfig b/configs/CPC45_ROMBOOT_defconfig
deleted file mode 100644
index 4aae7f6..0000000
--- a/configs/CPC45_ROMBOOT_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="BOOT_ROM"
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_CPC45=y
diff --git a/configs/CPC45_defconfig b/configs/CPC45_defconfig
deleted file mode 100644
index 77ae66c..0000000
--- a/configs/CPC45_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_CPC45=y
diff --git a/configs/CU824_defconfig b/configs/CU824_defconfig
deleted file mode 100644
index 0f22188..0000000
--- a/configs/CU824_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_CU824=y
diff --git a/configs/MUSENKI_defconfig b/configs/MUSENKI_defconfig
deleted file mode 100644
index 586364c..0000000
--- a/configs/MUSENKI_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_MUSENKI=y
diff --git a/configs/MVBLUE_defconfig b/configs/MVBLUE_defconfig
deleted file mode 100644
index f979983..0000000
--- a/configs/MVBLUE_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_MVBLUE=y
diff --git a/configs/Sandpoint8240_defconfig b/configs/Sandpoint8240_defconfig
deleted file mode 100644
index 332e4c0..0000000
--- a/configs/Sandpoint8240_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_SANDPOINT8240=y
diff --git a/configs/Sandpoint8245_defconfig b/configs/Sandpoint8245_defconfig
deleted file mode 100644
index b36757c..0000000
--- a/configs/Sandpoint8245_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_SANDPOINT8245=y
diff --git a/configs/eXalion_defconfig b/configs/eXalion_defconfig
deleted file mode 100644
index 9d7e090..0000000
--- a/configs/eXalion_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_EXALION=y
diff --git a/configs/utx8245_defconfig b/configs/utx8245_defconfig
deleted file mode 100644
index c2107cc..0000000
--- a/configs/utx8245_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC824X=y
-CONFIG_TARGET_UTX8245=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 5df0664..5d2875c 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,15 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+A3000 powerpc mpc824x - -
+CPC45 powerpc mpc824x - - Josef Wagner <Wagner@Microsys.de>
+CU824 powerpc mpc824x - - Wolfgang Denk <wd@denx.de>
+eXalion powerpc mpc824x - - Torsten Demke <torsten.demke@fci.com>
+MVBLUE powerpc mpc824x - -
+MUSENKI powerpc mpc824x - - Jim Thompson <jim@musenki.com>
+Sandpoint8240 powerpc mpc824x - - Wolfgang Denk <wd@denx.de>
+Sandpoint8245 powerpc mpc824x - - Jim Thompson <jim@musenki.com>
+utx8245 powerpc mpc824x - - Greg Allen <gallen@arlut.utexas.edu>
atc powerpc mpc8260 - - Wolfgang Denk <wd@denx.de>
CPU86 powerpc mpc8260 - - Wolfgang Denk <wd@denx.de>
CPU87 powerpc mpc8260 - -
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 91821f4..c506f79 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -5,7 +5,6 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_I82365) += i82365.o
obj-$(CONFIG_8xx) += mpc8xx_pcmcia.o
obj-$(CONFIG_IDE_TI_CARDBUS) += ti_pci1410a.o
obj-y += tqm8xx_pcmcia.o
diff --git a/drivers/pcmcia/i82365.c b/drivers/pcmcia/i82365.c
deleted file mode 100644
index 84a3d2e..0000000
--- a/drivers/pcmcia/i82365.c
+++ /dev/null
@@ -1,989 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- ********************************************************************
- *
- * Lots of code copied from:
- *
- * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
- * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
- * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
- */
-
-#include <common.h>
-
-#include <command.h>
-#include <pci.h>
-#include <pcmcia.h>
-#include <asm/io.h>
-
-#include <pcmcia/ss.h>
-#include <pcmcia/i82365.h>
-#include <pcmcia/yenta.h>
-#ifdef CONFIG_CPC45
-#include <pcmcia/cirrus.h>
-#else
-#include <pcmcia/ti113x.h>
-#endif
-
-static struct pci_device_id supported[] = {
-#ifdef CONFIG_CPC45
- {PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6729},
-#else
- {PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1510},
-#endif
- {0, 0}
-};
-
-#define CYCLE_TIME 120
-
-#ifdef CONFIG_CPC45
-extern int SPD67290Init (void);
-#endif
-
-#ifdef DEBUG
-static void i82365_dump_regions (pci_dev_t dev);
-#endif
-
-typedef struct socket_info_t {
- pci_dev_t dev;
- u_short bcr;
- u_char pci_lat, cb_lat, sub_bus, cache;
- u_int cb_phys;
-
- socket_cap_t cap;
- u_short type;
- u_int flags;
-#ifdef CONFIG_CPC45
- cirrus_state_t c_state;
-#else
- ti113x_state_t state;
-#endif
-} socket_info_t;
-
-#ifdef CONFIG_CPC45
-/* These definitions must match the pcic table! */
-typedef enum pcic_id {
- IS_PD6710, IS_PD672X, IS_VT83C469
-} pcic_id;
-
-typedef struct pcic_t {
- char *name;
-} pcic_t;
-
-static pcic_t pcic[] = {
- {" Cirrus PD6710: "},
- {" Cirrus PD672x: "},
- {" VIA VT83C469: "},
-};
-#endif
-
-static socket_info_t socket;
-static socket_state_t state;
-static struct pccard_mem_map mem;
-static struct pccard_io_map io;
-
-/*====================================================================*/
-
-/* Some PCI shortcuts */
-
-static int pci_readb (socket_info_t * s, int r, u_char * v)
-{
- return pci_read_config_byte (s->dev, r, v);
-}
-static int pci_writeb (socket_info_t * s, int r, u_char v)
-{
- return pci_write_config_byte (s->dev, r, v);
-}
-static int pci_readw (socket_info_t * s, int r, u_short * v)
-{
- return pci_read_config_word (s->dev, r, v);
-}
-static int pci_writew (socket_info_t * s, int r, u_short v)
-{
- return pci_write_config_word (s->dev, r, v);
-}
-#ifndef CONFIG_CPC45
-static int pci_readl (socket_info_t * s, int r, u_int * v)
-{
- return pci_read_config_dword (s->dev, r, v);
-}
-static int pci_writel (socket_info_t * s, int r, u_int v)
-{
- return pci_write_config_dword (s->dev, r, v);
-}
-#endif /* !CONFIG_CPC45 */
-
-/*====================================================================*/
-
-#ifdef CONFIG_CPC45
-
-#define cb_readb(s) readb((s)->cb_phys + 1)
-#define cb_writeb(s, v) writeb(v, (s)->cb_phys)
-#define cb_writeb2(s, v) writeb(v, (s)->cb_phys + 1)
-#define cb_readl(s, r) readl((s)->cb_phys + (r))
-#define cb_writel(s, r, v) writel(v, (s)->cb_phys + (r))
-
-
-static u_char i365_get (socket_info_t * s, u_short reg)
-{
- u_char val;
-#ifdef CONFIG_PCMCIA_SLOT_A
- int slot = 0;
-#else
- int slot = 1;
-#endif
-
- val = I365_REG (slot, reg);
-
- cb_writeb (s, val);
- val = cb_readb (s);
-
- debug ("i365_get slot:%x reg: %x val: %x\n", slot, reg, val);
- return val;
-}
-
-static void i365_set (socket_info_t * s, u_short reg, u_char data)
-{
-#ifdef CONFIG_PCMCIA_SLOT_A
- int slot = 0;
-#else
- int slot = 1;
-#endif
- u_char val;
-
- val = I365_REG (slot, reg);
-
- cb_writeb (s, val);
- cb_writeb2 (s, data);
-
- debug ("i365_set slot:%x reg: %x data:%x\n", slot, reg, data);
-}
-
-#else /* ! CONFIG_CPC45 */
-
-#define cb_readb(s, r) readb((s)->cb_phys + (r))
-#define cb_readl(s, r) readl((s)->cb_phys + (r))
-#define cb_writeb(s, r, v) writeb(v, (s)->cb_phys + (r))
-#define cb_writel(s, r, v) writel(v, (s)->cb_phys + (r))
-
-static u_char i365_get (socket_info_t * s, u_short reg)
-{
- return cb_readb (s, 0x0800 + reg);
-}
-
-static void i365_set (socket_info_t * s, u_short reg, u_char data)
-{
- cb_writeb (s, 0x0800 + reg, data);
-}
-#endif /* CONFIG_CPC45 */
-
-static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
-{
- i365_set (s, reg, i365_get (s, reg) | mask);
-}
-
-static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
-{
- i365_set (s, reg, i365_get (s, reg) & ~mask);
-}
-
-#if 0 /* not used */
-static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
-{
- u_char d = i365_get (s, reg);
-
- i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
-}
-
-static u_short i365_get_pair (socket_info_t * s, u_short reg)
-{
- return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
-}
-#endif /* not used */
-
-static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
-{
- i365_set (s, reg, data & 0xff);
- i365_set (s, reg + 1, data >> 8);
-}
-
-#ifdef CONFIG_CPC45
-/*======================================================================
-
- Code to save and restore global state information for Cirrus
- PD67xx controllers, and to set and report global configuration
- options.
-
-======================================================================*/
-
-#define flip(v,b,f) (v = ((f)<0) ? v : ((f) ? ((v)|(b)) : ((v)&(~b))))
-
-static void cirrus_get_state (socket_info_t * s)
-{
- int i;
- cirrus_state_t *p = &s->c_state;
-
- p->misc1 = i365_get (s, PD67_MISC_CTL_1);
- p->misc1 &= (PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
- p->misc2 = i365_get (s, PD67_MISC_CTL_2);
- for (i = 0; i < 6; i++)
- p->timer[i] = i365_get (s, PD67_TIME_SETUP (0) + i);
-
-}
-
-static void cirrus_set_state (socket_info_t * s)
-{
- int i;
- u_char misc;
- cirrus_state_t *p = &s->c_state;
-
- misc = i365_get (s, PD67_MISC_CTL_2);
- i365_set (s, PD67_MISC_CTL_2, p->misc2);
- if (misc & PD67_MC2_SUSPEND)
- udelay (50000);
- misc = i365_get (s, PD67_MISC_CTL_1);
- misc &= ~(PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
- i365_set (s, PD67_MISC_CTL_1, misc | p->misc1);
- for (i = 0; i < 6; i++)
- i365_set (s, PD67_TIME_SETUP (0) + i, p->timer[i]);
-}
-
-static u_int cirrus_set_opts (socket_info_t * s)
-{
- cirrus_state_t *p = &s->c_state;
- u_int mask = 0xffff;
- char buf[200] = {0};
-
- if (has_ring == -1)
- has_ring = 1;
- flip (p->misc2, PD67_MC2_IRQ15_RI, has_ring);
- flip (p->misc2, PD67_MC2_DYNAMIC_MODE, dynamic_mode);
-#if DEBUG
- if (p->misc2 & PD67_MC2_IRQ15_RI)
- strcat (buf, " [ring]");
- if (p->misc2 & PD67_MC2_DYNAMIC_MODE)
- strcat (buf, " [dyn mode]");
- if (p->misc1 & PD67_MC1_INPACK_ENA)
- strcat (buf, " [inpack]");
-#endif
-
- if (p->misc2 & PD67_MC2_IRQ15_RI)
- mask &= ~0x8000;
- if (has_led > 0) {
-#if DEBUG
- strcat (buf, " [led]");
-#endif
- mask &= ~0x1000;
- }
- if (has_dma > 0) {
-#if DEBUG
- strcat (buf, " [dma]");
-#endif
- mask &= ~0x0600;
- flip (p->misc2, PD67_MC2_FREQ_BYPASS, freq_bypass);
-#if DEBUG
- if (p->misc2 & PD67_MC2_FREQ_BYPASS)
- strcat (buf, " [freq bypass]");
-#endif
- }
-
- if (setup_time >= 0)
- p->timer[0] = p->timer[3] = setup_time;
- if (cmd_time > 0) {
- p->timer[1] = cmd_time;
- p->timer[4] = cmd_time * 2 + 4;
- }
- if (p->timer[1] == 0) {
- p->timer[1] = 6;
- p->timer[4] = 16;
- if (p->timer[0] == 0)
- p->timer[0] = p->timer[3] = 1;
- }
- if (recov_time >= 0)
- p->timer[2] = p->timer[5] = recov_time;
-
- debug ("i82365 Opt: %s [%d/%d/%d] [%d/%d/%d]\n",
- buf,
- p->timer[0], p->timer[1], p->timer[2],
- p->timer[3], p->timer[4], p->timer[5]);
-
- return mask;
-}
-
-#else /* !CONFIG_CPC45 */
-
-/*======================================================================
-
- Code to save and restore global state information for TI 1130 and
- TI 1131 controllers, and to set and report global configuration
- options.
-
-======================================================================*/
-
-static void ti113x_get_state (socket_info_t * s)
-{
- ti113x_state_t *p = &s->state;
-
- pci_readl (s, TI113X_SYSTEM_CONTROL, &p->sysctl);
- pci_readb (s, TI113X_CARD_CONTROL, &p->cardctl);
- pci_readb (s, TI113X_DEVICE_CONTROL, &p->devctl);
- pci_readb (s, TI1250_DIAGNOSTIC, &p->diag);
- pci_readl (s, TI12XX_IRQMUX, &p->irqmux);
-}
-
-static void ti113x_set_state (socket_info_t * s)
-{
- ti113x_state_t *p = &s->state;
-
- pci_writel (s, TI113X_SYSTEM_CONTROL, p->sysctl);
- pci_writeb (s, TI113X_CARD_CONTROL, p->cardctl);
- pci_writeb (s, TI113X_DEVICE_CONTROL, p->devctl);
- pci_writeb (s, TI1250_MULTIMEDIA_CTL, 0);
- pci_writeb (s, TI1250_DIAGNOSTIC, p->diag);
- pci_writel (s, TI12XX_IRQMUX, p->irqmux);
- i365_set_pair (s, TI113X_IO_OFFSET (0), 0);
- i365_set_pair (s, TI113X_IO_OFFSET (1), 0);
-}
-
-static u_int ti113x_set_opts (socket_info_t * s)
-{
- ti113x_state_t *p = &s->state;
- u_int mask = 0xffff;
-
- p->cardctl &= ~TI113X_CCR_ZVENABLE;
- p->cardctl |= TI113X_CCR_SPKROUTEN;
-
- return mask;
-}
-#endif /* CONFIG_CPC45 */
-
-/*======================================================================
-
- Routines to handle common CardBus options
-
-======================================================================*/
-
-/* Default settings for PCI command configuration register */
-#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
- PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
-
-static void cb_get_state (socket_info_t * s)
-{
- pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
- pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
- pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
- pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
- pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
- pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
-}
-
-static void cb_set_state (socket_info_t * s)
-{
-#ifndef CONFIG_CPC45
- pci_writel (s, CB_LEGACY_MODE_BASE, 0);
- pci_writel (s, PCI_BASE_ADDRESS_0, s->cb_phys);
-#endif
- pci_writew (s, PCI_COMMAND, CMD_DFLT);
- pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
- pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
- pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
- pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
- pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
- pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
-}
-
-static void cb_set_opts (socket_info_t * s)
-{
-#ifndef CONFIG_CPC45
- if (s->cache == 0)
- s->cache = 8;
- if (s->pci_lat == 0)
- s->pci_lat = 0xa8;
- if (s->cb_lat == 0)
- s->cb_lat = 0xb0;
-#endif
-}
-
-/*======================================================================
-
- Power control for Cardbus controllers: used both for 16-bit and
- Cardbus cards.
-
-======================================================================*/
-
-static int cb_set_power (socket_info_t * s, socket_state_t * state)
-{
- u_int reg = 0;
-
-#ifdef CONFIG_CPC45
-
- reg = I365_PWR_NORESET;
- if (state->flags & SS_PWR_AUTO)
- reg |= I365_PWR_AUTO;
- if (state->flags & SS_OUTPUT_ENA)
- reg |= I365_PWR_OUT;
- if (state->Vpp != 0) {
- if (state->Vpp == 120) {
- reg |= I365_VPP1_12V;
- puts (" 12V card found: ");
- } else if (state->Vpp == state->Vcc) {
- reg |= I365_VPP1_5V;
- } else {
- puts (" power not found: ");
- return -1;
- }
- }
- if (state->Vcc != 0) {
- reg |= I365_VCC_5V;
- if (state->Vcc == 33) {
- puts (" 3.3V card found: ");
- i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- } else if (state->Vcc == 50) {
- puts (" 5V card found: ");
- i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- } else {
- puts (" power not found: ");
- return -1;
- }
- }
-
- if (reg != i365_get (s, I365_POWER)) {
- reg = (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V);
- i365_set (s, I365_POWER, reg);
- }
-
-#else /* ! CONFIG_CPC45 */
-
- /* restart card voltage detection if it seems appropriate */
- if ((state->Vcc == 0) && (state->Vpp == 0) &&
- !(cb_readl (s, CB_SOCKET_STATE) & CB_SS_VSENSE))
- cb_writel (s, CB_SOCKET_FORCE, CB_SF_CVSTEST);
- switch (state->Vcc) {
- case 0:
- reg = 0;
- break;
- case 33:
- reg = CB_SC_VCC_3V;
- break;
- case 50:
- reg = CB_SC_VCC_5V;
- break;
- default:
- return -1;
- }
- switch (state->Vpp) {
- case 0:
- break;
- case 33:
- reg |= CB_SC_VPP_3V;
- break;
- case 50:
- reg |= CB_SC_VPP_5V;
- break;
- case 120:
- reg |= CB_SC_VPP_12V;
- break;
- default:
- return -1;
- }
- if (reg != cb_readl (s, CB_SOCKET_CONTROL))
- cb_writel (s, CB_SOCKET_CONTROL, reg);
-#endif /* CONFIG_CPC45 */
- return 0;
-}
-
-/*======================================================================
-
- Generic routines to get and set controller options
-
-======================================================================*/
-
-static void get_bridge_state (socket_info_t * s)
-{
-#ifdef CONFIG_CPC45
- cirrus_get_state (s);
-#else
- ti113x_get_state (s);
-#endif
- cb_get_state (s);
-}
-
-static void set_bridge_state (socket_info_t * s)
-{
- cb_set_state (s);
- i365_set (s, I365_GBLCTL, 0x00);
- i365_set (s, I365_GENCTL, 0x00);
-#ifdef CONFIG_CPC45
- cirrus_set_state (s);
-#else
- ti113x_set_state (s);
-#endif
-}
-
-static void set_bridge_opts (socket_info_t * s)
-{
-#ifdef CONFIG_CPC45
- cirrus_set_opts (s);
-#else
- ti113x_set_opts (s);
-#endif
- cb_set_opts (s);
-}
-
-/*====================================================================*/
-#define PD67_EXT_INDEX 0x2e /* Extension index */
-#define PD67_EXT_DATA 0x2f /* Extension data */
-#define PD67_EXD_VS1(s) (0x01 << ((s)<<1))
-
-#define pd67_ext_get(s, r) \
- (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
-
-static int i365_get_status (socket_info_t * s, u_int * value)
-{
- u_int status;
-#ifdef CONFIG_CPC45
- u_char val;
- u_char power, vcc, vpp;
- u_int powerstate;
-#endif
-
- status = i365_get (s, I365_IDENT);
- status = i365_get (s, I365_STATUS);
- *value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
- if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
- *value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
- } else {
- *value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
- *value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
- }
- *value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
- *value |= (status & I365_CS_READY) ? SS_READY : 0;
- *value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
-
-#ifdef CONFIG_CPC45
- /* Check for Cirrus CL-PD67xx chips */
- i365_set (s, PD67_CHIP_INFO, 0);
- val = i365_get (s, PD67_CHIP_INFO);
- s->type = -1;
- if ((val & PD67_INFO_CHIP_ID) == PD67_INFO_CHIP_ID) {
- val = i365_get (s, PD67_CHIP_INFO);
- if ((val & PD67_INFO_CHIP_ID) == 0) {
- s->type = (val & PD67_INFO_SLOTS) ? IS_PD672X : IS_PD6710;
- i365_set (s, PD67_EXT_INDEX, 0xe5);
- if (i365_get (s, PD67_EXT_INDEX) != 0xe5)
- s->type = IS_VT83C469;
- }
- } else {
- printf ("no Cirrus Chip found\n");
- *value = 0;
- return -1;
- }
-
- power = i365_get (s, I365_POWER);
- state.flags |= (power & I365_PWR_AUTO) ? SS_PWR_AUTO : 0;
- state.flags |= (power & I365_PWR_OUT) ? SS_OUTPUT_ENA : 0;
- vcc = power & I365_VCC_MASK;
- vpp = power & I365_VPP1_MASK;
- state.Vcc = state.Vpp = 0;
- if((vcc== 0) || (vpp == 0)) {
- /*
- * On the Cirrus we get the info which card voltage
- * we have in EXTERN DATA and write it to MISC_CTL1
- */
- powerstate = pd67_ext_get(s, PD67_EXTERN_DATA);
- if (powerstate & PD67_EXD_VS1(0)) {
- /* 5V Card */
- i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- } else {
- /* 3.3V Card */
- i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
- }
- i365_set (s, I365_POWER, (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V));
- power = i365_get (s, I365_POWER);
- }
- if (power & I365_VCC_5V) {
- state.Vcc = (i365_get(s, PD67_MISC_CTL_1) & PD67_MC1_VCC_3V) ? 33 : 50;
- }
-
- if (power == I365_VPP1_12V)
- state.Vpp = 120;
-
- /* IO card, RESET flags, IO interrupt */
- power = i365_get (s, I365_INTCTL);
- state.flags |= (power & I365_PC_RESET) ? 0 : SS_RESET;
- if (power & I365_PC_IOCARD)
- state.flags |= SS_IOCARD;
- state.io_irq = power & I365_IRQ_MASK;
-
- /* Card status change mask */
- power = i365_get (s, I365_CSCINT);
- state.csc_mask = (power & I365_CSC_DETECT) ? SS_DETECT : 0;
- if (state.flags & SS_IOCARD)
- state.csc_mask |= (power & I365_CSC_STSCHG) ? SS_STSCHG : 0;
- else {
- state.csc_mask |= (power & I365_CSC_BVD1) ? SS_BATDEAD : 0;
- state.csc_mask |= (power & I365_CSC_BVD2) ? SS_BATWARN : 0;
- state.csc_mask |= (power & I365_CSC_READY) ? SS_READY : 0;
- }
- debug ("i82365: GetStatus(0) = flags %#3.3x, Vcc %d, Vpp %d, "
- "io_irq %d, csc_mask %#2.2x\n", state.flags,
- state.Vcc, state.Vpp, state.io_irq, state.csc_mask);
-
-#else /* !CONFIG_CPC45 */
-
- status = cb_readl (s, CB_SOCKET_STATE);
- *value |= (status & CB_SS_32BIT) ? SS_CARDBUS : 0;
- *value |= (status & CB_SS_3VCARD) ? SS_3VCARD : 0;
- *value |= (status & CB_SS_XVCARD) ? SS_XVCARD : 0;
- *value |= (status & CB_SS_VSENSE) ? 0 : SS_PENDING;
- /* For now, ignore cards with unsupported voltage keys */
- if (*value & SS_XVCARD)
- *value &= ~(SS_DETECT | SS_3VCARD | SS_XVCARD);
-#endif /* CONFIG_CPC45 */
- return 0;
-} /* i365_get_status */
-
-static int i365_set_socket (socket_info_t * s, socket_state_t * state)
-{
- u_char reg;
-
- set_bridge_state (s);
-
- /* IO card, RESET flag */
- reg = 0;
- reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
- reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
- i365_set (s, I365_INTCTL, reg);
-
-#ifdef CONFIG_CPC45
- cb_set_power (s, state);
-
-#if 0
- /* Card status change interrupt mask */
- reg = s->cs_irq << 4;
- if (state->csc_mask & SS_DETECT)
- reg |= I365_CSC_DETECT;
- if (state->flags & SS_IOCARD) {
- if (state->csc_mask & SS_STSCHG)
- reg |= I365_CSC_STSCHG;
- } else {
- if (state->csc_mask & SS_BATDEAD)
- reg |= I365_CSC_BVD1;
- if (state->csc_mask & SS_BATWARN)
- reg |= I365_CSC_BVD2;
- if (state->csc_mask & SS_READY)
- reg |= I365_CSC_READY;
- }
- i365_set (s, I365_CSCINT, reg);
- i365_get (s, I365_CSC);
-#endif /* 0 */
-
-#else /* !CONFIG_CPC45 */
-
- reg = I365_PWR_NORESET;
- if (state->flags & SS_PWR_AUTO)
- reg |= I365_PWR_AUTO;
- if (state->flags & SS_OUTPUT_ENA)
- reg |= I365_PWR_OUT;
-
- cb_set_power (s, state);
- reg |= i365_get (s, I365_POWER) & (I365_VCC_MASK | I365_VPP1_MASK);
-
- if (reg != i365_get (s, I365_POWER))
- i365_set (s, I365_POWER, reg);
-#endif /* CONFIG_CPC45 */
-
- return 0;
-} /* i365_set_socket */
-
-/*====================================================================*/
-
-static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
-{
- u_short base, i;
- u_char map;
-
- debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
- mem->map, mem->flags, mem->speed,
- mem->sys_start, mem->sys_stop, mem->card_start);
-
- map = mem->map;
- if ((map > 4) ||
- (mem->card_start > 0x3ffffff) ||
- (mem->sys_start > mem->sys_stop) ||
- (mem->speed > 1000)) {
- return -1;
- }
-
- /* Turn off the window before changing anything */
- if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
- i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
-
- /* Take care of high byte, for PCI controllers */
- i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
-
- base = I365_MEM (map);
- i = (mem->sys_start >> 12) & 0x0fff;
- if (mem->flags & MAP_16BIT)
- i |= I365_MEM_16BIT;
- if (mem->flags & MAP_0WS)
- i |= I365_MEM_0WS;
- i365_set_pair (s, base + I365_W_START, i);
-
- i = (mem->sys_stop >> 12) & 0x0fff;
- switch (mem->speed / CYCLE_TIME) {
- case 0:
- break;
- case 1:
- i |= I365_MEM_WS0;
- break;
- case 2:
- i |= I365_MEM_WS1;
- break;
- default:
- i |= I365_MEM_WS1 | I365_MEM_WS0;
- break;
- }
- i365_set_pair (s, base + I365_W_STOP, i);
-
-#ifdef CONFIG_CPC45
- i = 0;
-#else
- i = ((mem->card_start - mem->sys_start) >> 12) & 0x3fff;
-#endif
- if (mem->flags & MAP_WRPROT)
- i |= I365_MEM_WRPROT;
- if (mem->flags & MAP_ATTRIB)
- i |= I365_MEM_REG;
- i365_set_pair (s, base + I365_W_OFF, i);
-
-#ifdef CONFIG_CPC45
- /* set System Memory map Upper Adress */
- i365_set(s, PD67_EXT_INDEX, PD67_MEM_PAGE(map));
- i365_set(s, PD67_EXT_DATA, ((mem->sys_start >> 24) & 0xff));
-#endif
-
- /* Turn on the window if necessary */
- if (mem->flags & MAP_ACTIVE)
- i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
- return 0;
-} /* i365_set_mem_map */
-
-static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
-{
- u_char map, ioctl;
-
- map = io->map;
- /* comment out: comparison is always false due to limited range of data type */
- if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
- (io->stop < io->start))
- return -1;
- /* Turn off the window before changing anything */
- if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
- i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
- i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
- i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
- ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
- if (io->speed)
- ioctl |= I365_IOCTL_WAIT (map);
- if (io->flags & MAP_0WS)
- ioctl |= I365_IOCTL_0WS (map);
- if (io->flags & MAP_16BIT)
- ioctl |= I365_IOCTL_16BIT (map);
- if (io->flags & MAP_AUTOSZ)
- ioctl |= I365_IOCTL_IOCS16 (map);
- i365_set (s, I365_IOCTL, ioctl);
- /* Turn on the window if necessary */
- if (io->flags & MAP_ACTIVE)
- i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
- return 0;
-} /* i365_set_io_map */
-
-/*====================================================================*/
-
-int i82365_init (void)
-{
- u_int val;
- int i;
-
-#ifdef CONFIG_CPC45
- if (SPD67290Init () != 0)
- return 1;
-#endif
- if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
- /* Controller not found */
- return 1;
- }
- debug ("i82365 Device Found!\n");
-
- pci_read_config_dword (socket.dev, PCI_BASE_ADDRESS_0, &socket.cb_phys);
- socket.cb_phys &= ~0xf;
-
-#ifdef CONFIG_CPC45
- /* + 0xfe000000 see MPC 8245 Users Manual Adress Map B */
- socket.cb_phys += 0xfe000000;
-#endif
-
- get_bridge_state (&socket);
- set_bridge_opts (&socket);
-
- i = i365_get_status (&socket, &val);
-
-#ifdef CONFIG_CPC45
- if (i > -1) {
- puts (pcic[socket.type].name);
- } else {
- printf ("i82365: Controller not found.\n");
- return 1;
- }
- if((val & SS_DETECT) != SS_DETECT){
- puts ("No card\n");
- return 1;
- }
-#else /* !CONFIG_CPC45 */
- if (val & SS_DETECT) {
- if (val & SS_3VCARD) {
- state.Vcc = state.Vpp = 33;
- puts (" 3.3V card found: ");
- } else if (!(val & SS_XVCARD)) {
- state.Vcc = state.Vpp = 50;
- puts (" 5.0V card found: ");
- } else {
- puts ("i82365: unsupported voltage key\n");
- state.Vcc = state.Vpp = 0;
- }
- } else {
- /* No card inserted */
- puts ("No card\n");
- return 1;
- }
-#endif /* CONFIG_CPC45 */
-
-#ifdef CONFIG_CPC45
- state.flags |= SS_OUTPUT_ENA;
-#else
- state.flags = SS_IOCARD | SS_OUTPUT_ENA;
- state.csc_mask = 0;
- state.io_irq = 0;
-#endif
-
- i365_set_socket (&socket, &state);
-
- for (i = 500; i; i--) {
- if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
- break;
- udelay (1000);
- }
-
- if (i == 0) {
- /* PC Card not ready for data transfer */
- puts ("i82365 PC Card not ready for data transfer\n");
- return 1;
- }
- debug (" PC Card ready for data transfer: ");
-
- mem.map = 0;
- mem.flags = MAP_ATTRIB | MAP_ACTIVE;
- mem.speed = 300;
- mem.sys_start = CONFIG_SYS_PCMCIA_MEM_ADDR;
- mem.sys_stop = CONFIG_SYS_PCMCIA_MEM_ADDR + CONFIG_SYS_PCMCIA_MEM_SIZE - 1;
- mem.card_start = 0;
- i365_set_mem_map (&socket, &mem);
-
-#ifdef CONFIG_CPC45
- mem.map = 1;
- mem.flags = MAP_ACTIVE;
- mem.speed = 300;
- mem.sys_start = CONFIG_SYS_PCMCIA_MEM_ADDR + CONFIG_SYS_PCMCIA_MEM_SIZE;
- mem.sys_stop = CONFIG_SYS_PCMCIA_MEM_ADDR + (2 * CONFIG_SYS_PCMCIA_MEM_SIZE) - 1;
- mem.card_start = 0;
- i365_set_mem_map (&socket, &mem);
-
-#else /* !CONFIG_CPC45 */
-
- io.map = 0;
- io.flags = MAP_AUTOSZ | MAP_ACTIVE;
- io.speed = 0;
- io.start = 0x0100;
- io.stop = 0x010F;
- i365_set_io_map (&socket, &io);
-
-#endif /* CONFIG_CPC45 */
-
-#ifdef DEBUG
- i82365_dump_regions (socket.dev);
-#endif
-
- return 0;
-}
-
-void i82365_exit (void)
-{
- io.map = 0;
- io.flags = 0;
- io.speed = 0;
- io.start = 0;
- io.stop = 0x1;
-
- i365_set_io_map (&socket, &io);
-
- mem.map = 0;
- mem.flags = 0;
- mem.speed = 0;
- mem.sys_start = 0;
- mem.sys_stop = 0x1000;
- mem.card_start = 0;
-
- i365_set_mem_map (&socket, &mem);
-
-#ifdef CONFIG_CPC45
- mem.map = 1;
- mem.flags = 0;
- mem.speed = 0;
- mem.sys_start = 0;
- mem.sys_stop = 0x1000;
- mem.card_start = 0;
-
- i365_set_mem_map (&socket, &mem);
-#else /* !CONFIG_CPC45 */
- socket.state.sysctl &= 0xFFFF00FF;
-#endif
- state.Vcc = state.Vpp = 0;
-
- i365_set_socket (&socket, &state);
-}
-
-/*======================================================================
-
- Debug stuff
-
-======================================================================*/
-
-#ifdef DEBUG
-static void i82365_dump_regions (pci_dev_t dev)
-{
- u_int tmp[2];
- u_int *mem = (void *) socket.cb_phys;
- u_char *cis = (void *) CONFIG_SYS_PCMCIA_MEM_ADDR;
- u_char *ide = (void *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_REG_OFFSET);
-
- pci_read_config_dword (dev, 0x00, tmp + 0);
- pci_read_config_dword (dev, 0x80, tmp + 1);
-
- printf ("PCI CONF: %08X ... %08X\n",
- tmp[0], tmp[1]);
- printf ("PCI MEM: ... %08X ... %08X\n",
- mem[0x8 / 4], mem[0x800 / 4]);
- printf ("CIS: ...%c%c%c%c%c%c%c%c...\n",
- cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
- cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
- printf ("CIS CONF: %02X %02X %02X ...\n",
- cis[0x200], cis[0x202], cis[0x204]);
- printf ("IDE: %02X %02X %02X %02X %02X %02X %02X %02X\n",
- ide[0], ide[1], ide[2], ide[3],
- ide[4], ide[5], ide[6], ide[7]);
-}
-#endif /* DEBUG */
diff --git a/include/configs/A3000.h b/include/configs/A3000.h
deleted file mode 100644
index 35e3e6f..0000000
--- a/include/configs/A3000.h
+++ /dev/null
@@ -1,293 +0,0 @@
-/*
- * (C) Copyright 2001, 2002, 2003
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-/*
- * Configuration settings for the A-3000 board (Artis Microsystems Inc.).
- * http://artismicro.com
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245 1
-#define CONFIG_A3000 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_BOOTDELAY 5
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#undef CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "A3000> " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-/* Print Buffer Size
- */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 8 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00400000 /* Default load address */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-
-/* #define CONFIG_TULIP */
-/* #define CONFIG_EEPRO100 */
-#define CONFIG_NATSEMI
-
-#define PCI_ENET0_IOADDR 0x80000000
-#define PCI_ENET0_MEMADDR 0x80000000
-#define PCI_ENET1_IOADDR 0x81000000
-#define PCI_ENET1_MEMADDR 0x81000000
-#define PCI_ENET2_IOADDR 0x82000000
-#define PCI_ENET2_MEMADDR 0x82000000
-#define PCI_ENET3_IOADDR 0x83000000
-#define PCI_ENET3_MEMADDR 0x83000000
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank on RCS#0 */
-#define CONFIG_SYS_FLASH_BASE1_PRELIM 0xFF000000 /* FLASH bank on RCS#1 */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH_BASE0_PRELIM
-#define CONFIG_SYS_FLASH_BANKS { CONFIG_SYS_FLASH_BASE0_PRELIM }
-
-/* even though FLASHP_BASE is FF800000, with 4MB is RCS0, the
- * reset vector is actually located at FFB00100, but the 8245
- * takes care of us.
- */
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
- /* Maximum amount of RAM.
- */
-#define CONFIG_SYS_MAX_RAM_SIZE 0x04000000 /* 0 .. 128 MB of (S)DRAM */
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-
-/* #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-
- /* Bit-field values for MCCR1.
- */
-#define CONFIG_SYS_ROMNAL 7
-#define CONFIG_SYS_ROMFAL 11
-#define CONFIG_SYS_DBUS_SIZE 0x3
-
- /* Bit-field values for MCCR2.
- */
-#define CONFIG_SYS_TSWAIT 0x5 /* Transaction Start Wait States timer */
-#define CONFIG_SYS_REFINT 0x400 /* Refresh interval FIXME: was 0t430 */
-
- /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
- */
-#define CONFIG_SYS_BSTOPRE 121
-
- /* Bit-field values for MCCR3.
- */
-#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
-
- /* Bit-field values for MCCR4.
- */
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval FIXME: was 2 */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval FIXME: was 5 */
-#define CONFIG_SYS_ACTORW 3 /* FIXME was 2 */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory FIXME: was 0x32*/
-
-#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note bottom 3 bits MUST be 0 */
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0xff
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max number of sectors per flash */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-
- /* Warining: environment is not EMBEDDED in the U-Boot code.
- * It's stored in flash separately.
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0xFFFE0000
-#define CONFIG_ENV_SIZE 0x00020000 /* Size of the Environment */
-#define CONFIG_ENV_SECT_SIZE 0x00020000 /* Size of the Environment Sector */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/CPC45.h b/include/configs/CPC45.h
deleted file mode 100644
index a75c52f..0000000
--- a/include/configs/CPC45.h
+++ /dev/null
@@ -1,489 +0,0 @@
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- *
- * Configuration settings for the CPC45 board.
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245 1
-#define CONFIG_CPC45 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#define CONFIG_BOOTDELAY 5
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-#if 1
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-#endif
-
-/* Print Buffer Size
- */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#if defined(CONFIG_BOOT_ROM)
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#else
-#define CONFIG_SYS_FLASH_BASE 0xFF800000
-#endif
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#define CONFIG_SYS_EUMB_ADDR 0xFCE00000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
-/* Maximum amount of RAM.
- */
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-#define DUART_DCR (CONFIG_SYS_EUMB_ADDR + 0x4511)
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33000000
-
-
-/* Bit-field values for MCCR1.
- */
-#define CONFIG_SYS_ROMNAL 0
-#define CONFIG_SYS_ROMFAL 8
-
-#define CONFIG_SYS_BANK0_ROW 0 /* SDRAM bank 7-0 row address */
-#define CONFIG_SYS_BANK1_ROW 0
-#define CONFIG_SYS_BANK2_ROW 0
-#define CONFIG_SYS_BANK3_ROW 0
-#define CONFIG_SYS_BANK4_ROW 0
-#define CONFIG_SYS_BANK5_ROW 0
-#define CONFIG_SYS_BANK6_ROW 0
-#define CONFIG_SYS_BANK7_ROW 0
-
-/* Bit-field values for MCCR2.
- */
-
-#define CONFIG_SYS_REFINT 0x2ec
-
-/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
- */
-#define CONFIG_SYS_BSTOPRE 160
-
-/* Bit-field values for MCCR3.
- */
-#define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */
-#define CONFIG_SYS_RDLAT 0 /* Data latancy from read command */
-
-/* Bit-field values for MCCR4.
- */
-#define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */
-#define CONFIG_SYS_ACTORW 2
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 0
-#define CONFIG_SYS_REGDIMM 0
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0xff
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
- /* currently accessed page in memory */
- /* see 8240 book for details */
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 39 /* Max number of sectors in one bank */
-#define INTEL_ID_28F160F3T 0x88F388F3 /* 16M = 1M x 16 top boot sector */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
- /* Warining: environment is not EMBEDDED in the ppcboot code.
- * It's stored in flash separately.
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x7F8000)
-#define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment */
-#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */
-#define CONFIG_ENV_SECT_SIZE 0x8000 /* Size of the Environment Sector */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*----------------------------------------------------------------------*/
-/* CPC45 Memory Map */
-/*----------------------------------------------------------------------*/
-#define SRAM_BASE 0x80000000 /* SRAM base address */
-#define SRAM_END 0x801FFFFF
-#define ST16552_A_BASE 0x80200000 /* ST16552 channel A */
-#define ST16552_B_BASE 0x80400000 /* ST16552 channel A */
-#define BCSR_BASE 0x80600000 /* board control / status registers */
-#define DISPLAY_BASE 0x80600040 /* DISPLAY base */
-#define PCMCIA_MEM_BASE 0x83000000 /* PCMCIA memory window base */
-#define PCMCIA_IO_BASE 0xFE000000 /* PCMCIA IO window base */
-
-#define CONFIG_SYS_SRAM_BASE SRAM_BASE
-#define CONFIG_SYS_SRAM_SIZE (SRAM_END - SRAM_BASE + 1)
-
-/*---------------------------------------------------------------------*/
-/* CPC45 Control/Status Registers */
-/*---------------------------------------------------------------------*/
-#define IRQ_ENA_1 *((volatile uchar*)(BCSR_BASE + 0x00))
-#define IRQ_STAT_1 *((volatile uchar*)(BCSR_BASE + 0x01))
-#define IRQ_ENA_2 *((volatile uchar*)(BCSR_BASE + 0x02))
-#define IRQ_STAT_2 *((volatile uchar*)(BCSR_BASE + 0x03))
-#define BOARD_CTRL *((volatile uchar*)(BCSR_BASE + 0x04))
-#define BOARD_STAT *((volatile uchar*)(BCSR_BASE + 0x05))
-#define WDG_START *((volatile uchar*)(BCSR_BASE + 0x06))
-#define WDG_PRESTOP *((volatile uchar*)(BCSR_BASE + 0x06))
-#define WDG_STOP *((volatile uchar*)(BCSR_BASE + 0x06))
-#define BOARD_REV *((volatile uchar*)(BCSR_BASE + 0x07))
-
-/* IRQ_ENA_1 bit definitions */
-#define I_ENA_1_IERA 0x80 /* INTA enable */
-#define I_ENA_1_IERB 0x40 /* INTB enable */
-#define I_ENA_1_IERC 0x20 /* INTC enable */
-#define I_ENA_1_IERD 0x10 /* INTD enable */
-
-/* IRQ_STAT_1 bit definitions */
-#define I_STAT_1_INTA 0x80 /* INTA status */
-#define I_STAT_1_INTB 0x40 /* INTB status */
-#define I_STAT_1_INTC 0x20 /* INTC status */
-#define I_STAT_1_INTD 0x10 /* INTD status */
-
-/* IRQ_ENA_2 bit definitions */
-#define I_ENA_2_IEAB 0x80 /* ABORT IRQ enable */
-#define I_ENA_2_IEK1 0x40 /* KEY1 IRQ enable */
-#define I_ENA_2_IEK2 0x20 /* KEY2 IRQ enable */
-#define I_ENA_2_IERT 0x10 /* RTC IRQ enable */
-#define I_ENA_2_IESM 0x08 /* LM81 IRQ enable */
-#define I_ENA_2_IEDG 0x04 /* DEGENERATING IRQ enable */
-#define I_ENA_2_IES2 0x02 /* ST16552/B IRQ enable */
-#define I_ENA_2_IES1 0x01 /* ST16552/A IRQ enable */
-
-/* IRQ_STAT_2 bit definitions */
-#define I_STAT_2_ABO 0x80 /* ABORT IRQ status */
-#define I_STAT_2_KY1 0x40 /* KEY1 IRQ status */
-#define I_STAT_2_KY2 0x20 /* KEY2 IRQ status */
-#define I_STAT_2_RTC 0x10 /* RTC IRQ status */
-#define I_STAT_2_SMN 0x08 /* LM81 IRQ status */
-#define I_STAT_2_DEG 0x04 /* DEGENERATING IRQ status */
-#define I_STAT_2_SIO2 0x02 /* ST16552/B IRQ status */
-#define I_STAT_2_SIO1 0x01 /* ST16552/A IRQ status */
-
-/* BOARD_CTRL bit definitions */
-#define USER_LEDS 2 /* 2 user LEDs */
-
-#if (USER_LEDS == 4)
-#define B_CTRL_WRSE 0x80
-#define B_CTRL_KRSE 0x40
-#define B_CTRL_FWRE 0x20 /* Flash write enable */
-#define B_CTRL_FWPT 0x10 /* Flash write protect */
-#define B_CTRL_LED3 0x08 /* LED 3 control */
-#define B_CTRL_LED2 0x04 /* LED 2 control */
-#define B_CTRL_LED1 0x02 /* LED 1 control */
-#define B_CTRL_LED0 0x01 /* LED 0 control */
-#else
-#define B_CTRL_WRSE 0x80
-#define B_CTRL_KRSE 0x40
-#define B_CTRL_FWRE_1 0x20 /* Flash write enable */
-#define B_CTRL_FWPT_1 0x10 /* Flash write protect */
-#define B_CTRL_LED1 0x08 /* LED 1 control */
-#define B_CTRL_LED0 0x04 /* LED 0 control */
-#define B_CTRL_FWRE_0 0x02 /* Flash write enable */
-#define B_CTRL_FWPT_0 0x01 /* Flash write protect */
-#endif
-
-/* BOARD_STAT bit definitions */
-#define B_STAT_WDGE 0x80
-#define B_STAT_WDGS 0x40
-#define B_STAT_WRST 0x20
-#define B_STAT_KRST 0x10
-#define B_STAT_CSW3 0x08 /* sitch bit 3 status */
-#define B_STAT_CSW2 0x04 /* sitch bit 2 status */
-#define B_STAT_CSW1 0x02 /* sitch bit 1 status */
-#define B_STAT_CSW0 0x01 /* sitch bit 0 status */
-
-/*---------------------------------------------------------------------*/
-/* Display addresses */
-/*---------------------------------------------------------------------*/
-#define DISP_UDC_RAM (DISPLAY_BASE + 0x08) /* UDC RAM */
-#define DISP_CHR_RAM (DISPLAY_BASE + 0x18) /* character Ram */
-#define DISP_FLASH (DISPLAY_BASE + 0x20) /* Flash Ram */
-
-#define DISP_UDC_ADR *((volatile uchar*)(DISPLAY_BASE + 0x00)) /* UDC Address Reg. */
-#define DISP_CWORD *((volatile uchar*)(DISPLAY_BASE + 0x10)) /* Control Word Reg. */
-
-#define DISP_DIG0 *((volatile uchar*)(DISP_CHR_RAM + 0x00)) /* Digit 0 address */
-#define DISP_DIG1 *((volatile uchar*)(DISP_CHR_RAM + 0x01)) /* Digit 0 address */
-#define DISP_DIG2 *((volatile uchar*)(DISP_CHR_RAM + 0x02)) /* Digit 0 address */
-#define DISP_DIG3 *((volatile uchar*)(DISP_CHR_RAM + 0x03)) /* Digit 0 address */
-#define DISP_DIG4 *((volatile uchar*)(DISP_CHR_RAM + 0x04)) /* Digit 0 address */
-#define DISP_DIG5 *((volatile uchar*)(DISP_CHR_RAM + 0x05)) /* Digit 0 address */
-#define DISP_DIG6 *((volatile uchar*)(DISP_CHR_RAM + 0x06)) /* Digit 0 address */
-#define DISP_DIG7 *((volatile uchar*)(DISP_CHR_RAM + 0x07)) /* Digit 0 address */
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_SYS_EARLY_PCI_INIT
-#undef CONFIG_PCI_PNP
-#undef CONFIG_PCI_SCAN_SHOW
-
-
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-
-#define PCI_ENET0_IOADDR 0x82000000
-#define PCI_ENET0_MEMADDR 0x82000000
-#define PCI_PLX9030_IOADDR 0x82100000
-#define PCI_PLX9030_MEMADDR 0x82100000
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_I82365
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR PCMCIA_MEM_BASE
-#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x1000
-
-#define CONFIG_PCMCIA_SLOT_A
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_RESET /* reset for IDE not supported */
-#define CONFIG_IDE_LED /* LED for IDE is supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-#define CONFIG_SYS_ATA_DATA_OFFSET CONFIG_SYS_PCMCIA_MEM_SIZE
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x400)
-
-#define CONFIG_DOS_PARTITION
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/CU824.h b/include/configs/CU824.h
deleted file mode 100644
index dc98a56..0000000
--- a/include/configs/CU824.h
+++ /dev/null
@@ -1,286 +0,0 @@
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- *
- * Configuration settings for the CU824 board.
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8240 1
-#define CONFIG_CU824 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */
-#define CONFIG_BOOTDELAY 5
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-#if 1
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-#endif
-
-/* Print Buffer Size
- */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#define CONFIG_SYS_EUMB_ADDR 0xFCE00000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
- /* Maximum amount of RAM.
- */
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 4
-
-#define CONFIG_SYS_NS16550_CLK (14745600 / 2)
-
-#define CONFIG_SYS_NS16550_COM1 0xFE800080
-#define CONFIG_SYS_NS16550_COM2 0xFE8000C0
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33000000
-
- /* Bit-field values for MCCR1.
- */
-#define CONFIG_SYS_ROMNAL 0
-#define CONFIG_SYS_ROMFAL 7
-
- /* Bit-field values for MCCR2.
- */
-#define CONFIG_SYS_REFINT 430 /* Refresh interval */
-
- /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
- */
-#define CONFIG_SYS_BSTOPRE 192
-
- /* Bit-field values for MCCR3.
- */
-#define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */
-#define CONFIG_SYS_RDLAT 3 /* Data latancy from read command */
-
- /* Bit-field values for MCCR4.
- */
-#define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */
-#define CONFIG_SYS_ACTORW 2
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0xff
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 39 /* Max number of sectors in one bank */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
- /* Warining: environment is not EMBEDDED in the U-Boot code.
- * It's stored in flash separately.
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#if 0
-#define CONFIG_ENV_ADDR 0xFF008000
-#define CONFIG_ENV_SIZE 0x8000 /* Size of the Environment Sector */
-#else
-#define CONFIG_ENV_ADDR 0xFFFC0000
-#define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment */
-#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_TULIP
-#define CONFIG_TULIP_USE_IO
-
-#define CONFIG_SYS_ETH_DEV_FN 0x7800
-#define CONFIG_SYS_ETH_IOBASE 0x00104000
-
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define PCI_ENET0_IOADDR 0x00104000
-#define PCI_ENET0_MEMADDR 0x80000000
-#endif /* __CONFIG_H */
diff --git a/include/configs/MUSENKI.h b/include/configs/MUSENKI.h
deleted file mode 100644
index c5c9290..0000000
--- a/include/configs/MUSENKI.h
+++ /dev/null
@@ -1,275 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- *
- * Configuration settings for the MUSENKI board.
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245 1
-#define CONFIG_MUSENKI 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_BOOTDELAY 5
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#undef CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-/* Print Buffer Size
- */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 8 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_TULIP
-
-#define PCI_ENET0_IOADDR 0x80000000
-#define PCI_ENET0_MEMADDR 0x80000000
-#define PCI_ENET1_IOADDR 0x81000000
-#define PCI_ENET1_MEMADDR 0x81000000
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank on RCS#0 */
-#define CONFIG_SYS_FLASH_BASE1_PRELIM 0xFF000000 /* FLASH bank on RCS#1 */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH_BASE0_PRELIM
-
-/* even though FLASHP_BASE is FF800000, with 4MB is RCS0, the
- * reset vector is actually located at FFB00100, but the 8245
- * takes care of us.
- */
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
- /* Maximum amount of RAM.
- */
-#define CONFIG_SYS_MAX_RAM_SIZE 0x08000000 /* 0 .. 128 MB of (S)DRAM */
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-
-/* #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-
- /* Bit-field values for MCCR1.
- */
-#define CONFIG_SYS_ROMNAL 7
-#define CONFIG_SYS_ROMFAL 11
-#define CONFIG_SYS_DBUS_SIZE 0x3
-
- /* Bit-field values for MCCR2.
- */
-#define CONFIG_SYS_TSWAIT 0x5 /* Transaction Start Wait States timer */
-#define CONFIG_SYS_REFINT 0x400 /* Refresh interval FIXME: was 0t430 */
-
- /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
- */
-#define CONFIG_SYS_BSTOPRE 121
-
- /* Bit-field values for MCCR3.
- */
-#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
-
- /* Bit-field values for MCCR4.
- */
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval FIXME: was 2 */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval FIXME: was 5 */
-#define CONFIG_SYS_ACTORW 3 /* FIXME was 2 */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory FIXME: was 0x32*/
-
-#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note bottom 3 bits MUST be 0 */
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0xff
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors per flash */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-
- /* Warining: environment is not EMBEDDED in the U-Boot code.
- * It's stored in flash separately.
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0xFFFF0000
-#define CONFIG_ENV_SIZE 0x00010000 /* Size of the Environment */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Size of the Environment Sector */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/MVBLUE.h b/include/configs/MVBLUE.h
deleted file mode 100644
index aa2d9c0..0000000
--- a/include/configs/MVBLUE.h
+++ /dev/null
@@ -1,325 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define MV_VERSION "v0.2.0"
-
-/* LED0 = Power , LED1 = Error , LED2-5 = error code, LED6-7=00 -->PPCBoot error */
-#define ERR_NONE 0
-#define ERR_ENV 1
-#define ERR_BOOTM_BADMAGIC 2
-#define ERR_BOOTM_BADCRC 3
-#define ERR_BOOTM_GUNZIP 4
-#define ERR_BOOTP_TIMEOUT 5
-#define ERR_DHCP 6
-#define ERR_TFTP 7
-#define ERR_NOLAN 8
-#define ERR_LANDRV 9
-
-#define CONFIG_BOARD_TYPES 1
-#define MVBLUE_BOARD_BOX 1
-#define MVBLUE_BOARD_LYNX 2
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#define CONFIG_SYS_LDSCRIPT "board/mvblue/u-boot.lds"
-
-#if 0
-#define ERR_LED(code) do { if (code) \
- *(volatile char *)(0xff000003) = ( 3 | (code<<4) ) & 0xf3; \
- else \
- *(volatile char *)(0xff000003) = ( 1 ); \
-} while(0)
-#else
-#define ERR_LED(code)
-#endif
-
-#define CONFIG_MPC8245 1
-#define CONFIG_MVBLUE 1
-
-#define CONFIG_CLOCKS_IN_MHZ 1
-
-#define CONFIG_BOARD_TYPES 1
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOT_RETRY_TIME -1
-
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT \
- "autoboot in %d seconds (stop with 's')...\n", bootdelay
-#define CONFIG_AUTOBOOT_STOP_STR "s"
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_RESET_TO_RETRY 60
-
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_RUN
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_NISDOMAIN
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_TIMEOFFSET
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-#define CONFIG_BOOTCOMMAND "run nfsboot"
-#define CONFIG_BOOTARGS "root=/dev/mtdblock5 ro rootfstype=jffs2"
-
-#define CONFIG_NFSBOOTCOMMAND "bootp; run nfsargs addcons;bootm"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console_nr=0\0" \
- "dhcp_client_id=mvBOX-XP\0" \
- "dhcp_vendor-class-identifier=mvBOX\0" \
- "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" \
- "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" \
- "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" \
- "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \
- "addcons=setenv bootargs ${bootargs} console=ttyS${console_nr},${baudrate}N8\0" \
- "mv_version=" MV_VERSION "\0" \
- "bootretry=30\0"
-
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-
-#define CONFIG_NET_RETRY_COUNT 5
-
-#define CONFIG_TULIP
-#define CONFIG_TULIP_FIX_DAVICOM 1
-#define CONFIG_ETHADDR b6:b4:45:eb:fb:c0
-
-#define CONFIG_HW_WATCHDOG
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start@0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_MONITOR_LEN 0x00100000
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */
-
-/* Maximum amount of RAM. */
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 0 .. 256MB of (S)DRAM */
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-/*
- * serial configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33000000
-
-/* Bit-field values for MCCR1. */
-#define CONFIG_SYS_ROMNAL 7
-#define CONFIG_SYS_ROMFAL 11
-
-/* Bit-field values for MCCR2. */
-#define CONFIG_SYS_TSWAIT 0x5
-#define CONFIG_SYS_REFINT 430
-
-/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
-#define CONFIG_SYS_BSTOPRE 121
-
-/* Bit-field values for MCCR3. */
-#define CONFIG_SYS_REFREC 8
-
-/* Bit-field values for MCCR4. */
-#define CONFIG_SYS_PRETOACT 3
-#define CONFIG_SYS_ACTTOPRE 5
-#define CONFIG_SYS_ACTORW 3
-#define CONFIG_SYS_SDMODE_CAS_LAT 3
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-#define CONFIG_SYS_DBUS_SIZE2 1
-#define CONFIG_SYS_SDMODE_WRAP 0
-
-#define CONFIG_SYS_PGMAX 0x32
-#define CONFIG_SYS_SDRAM_DSCD 0x20
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0xff
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#undef CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 63 /* Max number of sectors per flash */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 12000
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000
-
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#define CONFIG_ENV_OFFSET 0x00010000
-#define CONFIG_ENV_SIZE 0x00010000
-#define CONFIG_ENV_SECT_SIZE 0x00010000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-#endif /* __CONFIG_H */
diff --git a/include/configs/Sandpoint8240.h b/include/configs/Sandpoint8240.h
deleted file mode 100644
index 2c0cb89..0000000
--- a/include/configs/Sandpoint8240.h
+++ /dev/null
@@ -1,398 +0,0 @@
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8240 1
-#define CONFIG_SANDPOINT 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#define CONFIG_SYS_LDSCRIPT "board/sandpoint/u-boot.lds"
-
-#if 0
-#define USE_DINK32 1
-#else
-#undef USE_DINK32
-#endif
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run net_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "net_self=tftp ${kernel_addr} ${bootfile};" \
- "tftp ${ramdisk_addr} ${ramdisk};" \
- "run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp ${kernel_addr} ${bootfile};" \
- "run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- "bootfile=/tftpboot/SP8240/uImage\0" \
- "ramdisk=/tftpboot/SP8240/uRamdisk\0" \
- "kernel_addr=200000\0" \
- "ramdisk_addr=400000\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_DRAM_SPEED 100 /* MHz */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-
-#define PCI_ENET0_IOADDR 0x80000000
-#define PCI_ENET0_MEMADDR 0x80000000
-#define PCI_ENET1_IOADDR 0x81000000
-#define PCI_ENET1_MEMADDR 0x81000000
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#if defined (USE_DINK32)
-#define CONFIG_SYS_MONITOR_LEN 0x00030000
-#define CONFIG_SYS_MONITOR_BASE 0x00090000
-#define CONFIG_SYS_RAMBOOT 1
-#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#else
-#undef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN 0x00030000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#endif
-
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-#if 0
-#define CONFIG_SYS_FLASH_SIZE (512 * 1024) /* sandpoint has tiny eeprom */
-#else
-#define CONFIG_SYS_FLASH_SIZE (1024 * 1024) /* Unity has onboard 1MByte flash */
-#endif
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_ISA_MEM 0xFD000000
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-#define CONFIG_SYS_FLASH_RANGE_BASE 0xFF000000 /* flash memory address range */
-#define CONFIG_SYS_FLASH_RANGE_SIZE 0x01000000
-#define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */
-#define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#undef CONFIG_SYS_I2C_SOFT
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_SPEED 400000
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#error "Soft I2C is not configured properly. Please review!"
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#endif /* CONFIG_SYS_I2C_SOFT */
-
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* write page size */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
-
-
-#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM }
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-
-/* #define CONFIG_WINBOND_83C553 1 / *has a winbond bridge */
-#define CONFIG_SYS_USE_WINBOND_IDE 0 /*use winbond 83c553 internal IDE ctrlr */
-#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR 0x80005800 /*pci-isa bridge config addr */
-#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR 0x80005900 /*ide config addr */
-
-#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-/*
- * NS87308 Configuration
- */
-#define CONFIG_NS87308 /* Nat Semi super-io controller on ISA bus */
-
-#define CONFIG_SYS_NS87308_BADDR_10 1
-
-#define CONFIG_SYS_NS87308_DEVS ( CONFIG_SYS_NS87308_UART1 | \
- CONFIG_SYS_NS87308_UART2 | \
- CONFIG_SYS_NS87308_POWRMAN | \
- CONFIG_SYS_NS87308_RTC_APC )
-
-#undef CONFIG_SYS_NS87308_PS2MOD
-
-#define CONFIG_SYS_NS87308_CS0_BASE 0x0076
-#define CONFIG_SYS_NS87308_CS0_CONF 0x30
-#define CONFIG_SYS_NS87308_CS1_BASE 0x0075
-#define CONFIG_SYS_NS87308_CS1_CONF 0x30
-#define CONFIG_SYS_NS87308_CS2_BASE 0x0074
-#define CONFIG_SYS_NS87308_CS2_CONF 0x30
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK 1843200
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 1
-
-#define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */
-#define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */
-
-#define CONFIG_SYS_REFINT 430 /* no of clock cycles between CBR refresh cycles */
-
-/* the following are for SDRAM only*/
-#define CONFIG_SYS_BSTOPRE 121 /* Burst To Precharge, sets open page interval */
-#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
-#define CONFIG_SYS_RDLAT 4 /* data latency from read command */
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */
-
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-
-/* memory bank settings*/
-/*
- * only bits 20-29 are actually used from these vales to set the
- * start/end address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x00000000
-#define CONFIG_SYS_BANK4_END 0x00000000
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x00000000
-#define CONFIG_SYS_BANK5_END 0x00000000
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x00000000
-#define CONFIG_SYS_BANK6_END 0x00000000
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x00000000
-#define CONFIG_SYS_BANK7_END 0x00000000
-#define CONFIG_SYS_BANK7_ENABLE 0
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE 0x01
-
-#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */
- /* see 8240 book for bit definitions */
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
- /* currently accessed page in memory */
- /* see 8240 book for details */
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#if defined(USE_DINK32)
-#define CONFIG_SYS_IBAT1L (0x40000000 | BATL_PP_00 )
-#define CONFIG_SYS_IBAT1U (0x40000000 | BATU_BL_128K )
-#else
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#endif
-
-/* PCI memory */
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Flash, config addrs, etc */
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 20 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/* values according to the manual */
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-#undef NR_8259_INTS
-#define NR_8259_INTS 1
-
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/Sandpoint8245.h b/include/configs/Sandpoint8245.h
deleted file mode 100644
index 2664d5b..0000000
--- a/include/configs/Sandpoint8245.h
+++ /dev/null
@@ -1,376 +0,0 @@
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245 1
-#define CONFIG_SANDPOINT 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#define CONFIG_SYS_LDSCRIPT "board/sandpoint/u-boot.lds"
-
-#if 0
-#define USE_DINK32 1
-#else
-#undef USE_DINK32
-#endif
-
-#define CONFIG_CONS_INDEX 3 /* set to '3' for on-chip DUART */
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_DRAM_SPEED 100 /* MHz */
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NATSEMI
-#define CONFIG_NS8382X
-
-#define PCI_ENET0_IOADDR 0x80000000
-#define PCI_ENET0_MEMADDR 0x80000000
-#define PCI_ENET1_IOADDR 0x81000000
-#define PCI_ENET1_MEMADDR 0x81000000
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#if defined (USE_DINK32)
-#define CONFIG_SYS_MONITOR_LEN 0x00030000
-#define CONFIG_SYS_MONITOR_BASE 0x00090000
-#define CONFIG_SYS_RAMBOOT 1
-#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#else
-#undef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN 0x00030000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#endif
-
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-#if 0
-#define CONFIG_SYS_FLASH_SIZE (512 * 1024) /* sandpoint has tiny eeprom */
-#else
-#define CONFIG_SYS_FLASH_SIZE (1024 * 1024) /* Unity has onboard 1MByte flash */
-#endif
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_ISA_MEM 0xFD000000
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-#define CONFIG_SYS_FLASH_RANGE_BASE 0xFF000000 /* flash memory address range */
-#define CONFIG_SYS_FLASH_RANGE_SIZE 0x01000000
-#define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */
-#define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#undef CONFIG_SYS_I2C_SOFT
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#error "Soft I2C is not configured properly. Please review!"
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#endif /* CONFIG_SYS_I2C_SOFT */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM }
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-
-/* #define CONFIG_WINBOND_83C553 1 / *has a winbond bridge */
-#define CONFIG_SYS_USE_WINBOND_IDE 0 /*use winbond 83c553 internal IDE ctrlr */
-#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR 0x80005800 /*pci-isa bridge config addr */
-#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR 0x80005900 /*ide config addr */
-
-#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-/*
- * NS87308 Configuration
- */
-#define CONFIG_NS87308 /* Nat Semi super-io controller on ISA bus */
-
-#define CONFIG_SYS_NS87308_BADDR_10 1
-
-#define CONFIG_SYS_NS87308_DEVS ( CONFIG_SYS_NS87308_UART1 | \
- CONFIG_SYS_NS87308_UART2 | \
- CONFIG_SYS_NS87308_POWRMAN | \
- CONFIG_SYS_NS87308_RTC_APC )
-
-#undef CONFIG_SYS_NS87308_PS2MOD
-
-#define CONFIG_SYS_NS87308_CS0_BASE 0x0076
-#define CONFIG_SYS_NS87308_CS0_CONF 0x30
-#define CONFIG_SYS_NS87308_CS1_BASE 0x0075
-#define CONFIG_SYS_NS87308_CS1_CONF 0x30
-#define CONFIG_SYS_NS87308_CS2_BASE 0x0074
-#define CONFIG_SYS_NS87308_CS2_CONF 0x30
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#if (CONFIG_CONS_INDEX > 2)
-#define CONFIG_SYS_NS16550_CLK CONFIG_DRAM_SPEED*1000000
-#else
-#define CONFIG_SYS_NS16550_CLK 1843200
-#endif
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-
-#define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */
-#define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */
-
-#define CONFIG_SYS_REFINT 430 /* no of clock cycles between CBR refresh cycles */
-
-/* the following are for SDRAM only*/
-#define CONFIG_SYS_BSTOPRE 121 /* Burst To Precharge, sets open page interval */
-#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
-#define CONFIG_SYS_RDLAT 4 /* data latency from read command */
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#if 0
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* OBSOLETE! SDMODE Burst length 2=4, 3=8 */
-#endif
-
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-
-
-/* memory bank settings*/
-/*
- * only bits 20-29 are actually used from these vales to set the
- * start/end address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x00000000
-#define CONFIG_SYS_BANK4_END 0x00000000
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x00000000
-#define CONFIG_SYS_BANK5_END 0x00000000
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x00000000
-#define CONFIG_SYS_BANK6_END 0x00000000
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x00000000
-#define CONFIG_SYS_BANK7_END 0x00000000
-#define CONFIG_SYS_BANK7_ENABLE 0
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE 0x01
-
-#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */
- /* see 8240 book for bit definitions */
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
- /* currently accessed page in memory */
- /* see 8240 book for details */
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#if defined(USE_DINK32)
-#define CONFIG_SYS_IBAT1L (0x40000000 | BATL_PP_00 )
-#define CONFIG_SYS_IBAT1U (0x40000000 | BATU_BL_128K )
-#else
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#endif
-
-/* PCI memory */
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Flash, config addrs, etc */
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 20 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/* values according to the manual */
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-#undef NR_8259_INTS
-#define NR_8259_INTS 1
-
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/eXalion.h b/include/configs/eXalion.h
deleted file mode 100644
index 940be1f..0000000
--- a/include/configs/eXalion.h
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-/* #define CONFIG_MPC8240 1 */
-#define CONFIG_MPC8245 1
-#define CONFIG_EXALION 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#if defined (CONFIG_MPC8240)
- /* #warning ---------- eXalion with MPC8240 --------------- */
-#elif defined (CONFIG_MPC8245)
- /* #warning ++++++++++ eXalion with MPC8245 +++++++++++++++ */
-#elif defined (CONFIG_MPC8245) && defined (CONFIG_MPC8245)
-#error #### Both types of MPC824x defined (CONFIG_8240 and CONFIG_8245)
-#else
-#error #### Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-/* older kernels need clock in MHz newer in Hz */
- /* #define CONFIG_CLOCKS_IN_MHZ 1 */ /* clocks passsed to Linux in MHz */
-#undef CONFIG_CLOCKS_IN_MHZ
-
-#define CONFIG_BOOTDELAY 10
-
-
- /*#define CONFIG_DRAM_SPEED 66 */ /* MHz */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_PCI
-
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-#define CONFIG_MISC_INIT_R 1
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 1 GBytes - initdram() will */
- /* return real value. */
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#undef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-#define CONFIG_SYS_INIT_DATA_SIZE 128
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE)
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-
-#if defined (CONFIG_MPC8240)
-#define CONFIG_SYS_FLASH_BASE 0xFFE00000
-#define CONFIG_SYS_FLASH_SIZE (2 * 1024 * 1024) /* onboard 2MByte flash */
-#elif defined (CONFIG_MPC8245)
-#define CONFIG_SYS_FLASH_BASE 0xFFC00000
-#define CONFIG_SYS_FLASH_SIZE (4 * 1024 * 1024) /* onboard 4MByte flash */
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Size of one Flash sector */
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE /* Use one Flash sector for environment */
-#define CONFIG_ENV_ADDR 0xFFFC0000
-#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */
-
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-#define CONFIG_SYS_ALT_MEMTEST 1 /* use real memory test */
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-/* #define CONFIG_SYS_ISA_MEM 0xFD000000 */
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors per flash */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE
-#define FLASH_BASE1_PRELIM 0
-
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- */
-#define CONFIG_PCI 1 /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_EEPRO100 1
-
-#define PCI_ENET0_MEMADDR 0x80000000 /* Intel 82559ER */
-#define PCI_ENET0_IOADDR 0x80000000
-#define PCI_ENET1_MEMADDR 0x81000000 /* Intel 82559ER */
-#define PCI_ENET1_IOADDR 0x81000000
-#define PCI_ENET2_MEMADDR 0x82000000 /* Broadcom BCM569xx */
-#define PCI_ENET2_IOADDR 0x82000000
-#define PCI_ENET3_MEMADDR 0x83000000 /* Broadcom BCM56xx */
-#define PCI_ENET3_IOADDR 0x83000000
-
-/*-----------------------------------------------------------------------
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550 1
-#define CONFIG_SYS_NS16550_SERIAL 1
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 38400
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#if (CONFIG_CONS_INDEX == 1)
-#define CONFIG_SYS_NS16550_CLK 1843200 /* COM1 only ! */
-#else
-#define CONFIG_SYS_NS16550_CLK ({ extern ulong get_bus_freq (ulong); get_bus_freq (0); })
-#endif
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + 0x3F8)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*-----------------------------------------------------------------------
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*-----------------------------------------------------------------------
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 /* for MPC8240 only */
-
- /*#define CONFIG_133MHZ_DRAM 1 */ /* For 133 MHZ DRAM only !!!!!!!!!!! */
-
-#if defined (CONFIG_MPC8245)
-/* Bit-field values for PMCR2. */
-#if defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_DLL_EXTEND 0x80 /* use DLL extended range - 133MHz only */
-#define CONFIG_SYS_PCI_HOLD_DEL 0x20 /* delay and hold timing - 133MHz only */
-#endif
-
-/* Bit-field values for MIOCR1. */
-#if !defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_DLL_MAX_DELAY 0x04 /* longer DLL delay line - 66MHz only */
-#endif
-/* Bit-field values for MIOCR2. */
-#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay */
- /* - note bottom 3 bits MUST be 0 */
-#endif
-
-/* Bit-field values for MCCR1. */
-#define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */
-#define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */
-
-/* Bit-field values for MCCR2. */
-#define CONFIG_SYS_TSWAIT 0x5 /* Transaction Start Wait States timer */
-#if defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_REFINT 1300 /* no of clock cycles between CBR */
-#else /* refresh cycles */
-#define CONFIG_SYS_REFINT 750
-#endif
-
-/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
-#if defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_BSTOPRE 1023
-#else
-#define CONFIG_SYS_BSTOPRE 250
-#endif
-
-/* Bit-field values for MCCR3. */
-/* the following are for SDRAM only */
-
-#if defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_REFREC 9 /* Refresh to activate interval */
-#else
-#define CONFIG_SYS_REFREC 5 /* Refresh to activate interval */
-#endif
-#if defined (CONFIG_MPC8240)
-#define CONFIG_SYS_RDLAT 2 /* data latency from read command */
-#endif
-
-/* Bit-field values for MCCR4. */
-#if defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 7 /* Activate to Precharge interval */
-#define CONFIG_SYS_ACTORW 5 /* Activate to R/W */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
-#else
-#if 0
-#define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 3 /* Activate to Precharge interval */
-#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */
-#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */
-#endif
-#define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
-#endif
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */
-#define CONFIG_SYS_REGDIMM 0
-#if defined (CONFIG_MPC8240)
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 0
-#elif defined (CONFIG_MPC8245)
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 0
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
-
-/*-----------------------------------------------------------------------
- memory bank settings
- * only bits 20-29 are actually used from these vales to set the
- * start/end address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x00000000
-#define CONFIG_SYS_BANK4_END 0x00000000
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x00000000
-#define CONFIG_SYS_BANK5_END 0x00000000
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x00000000
-#define CONFIG_SYS_BANK6_END 0x00000000
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x00000000
-#define CONFIG_SYS_BANK7_END 0x00000000
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-/*-----------------------------------------------------------------------
- * Memory bank enable bitmask, specifying which of the banks defined above
- are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE 0x01
-
-#if defined (CONFIG_MPC8240)
-#define CONFIG_SYS_ODCR 0xDF /* configures line driver impedances, */
- /* see 8240 book for bit definitions */
-#elif defined (CONFIG_MPC8245)
-#if defined (CONFIG_133MHZ_DRAM)
-#define CONFIG_SYS_ODCR 0xFE /* configures line driver impedances - 133MHz */
-#else
-#define CONFIG_SYS_ODCR 0xDE /* configures line driver impedances - 66MHz */
-#endif
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
- /* currently accessed page in memory */
- /* see 8240 book for details */
-
-/*-----------------------------------------------------------------------
- * Block Address Translation (BAT) register settings.
- */
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-/* PCI memory */
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Flash, config addrs, etc */
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/* values according to the manual */
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-#undef NR_8259_INTS
-#define NR_8259_INTS 1
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- */
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 2 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO /* base address */
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
-#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-
-#define CONFIG_ATAPI
-
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* reset for ide supported... */
-#undef CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
-
-/*-----------------------------------------------------------------------
- * DISK Partition support
- */
-#define CONFIG_DOS_PARTITION
-
-/*-----------------------------------------------------------------------
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/utx8245.h b/include/configs/utx8245.h
deleted file mode 100644
index 5be62ec..0000000
--- a/include/configs/utx8245.h
+++ /dev/null
@@ -1,408 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * Gregory E. Allen, gallen at arlut.utexas.edu
- * Matthew E. Karger, karger at arlut.utexas.edu
- * Applied Research Laboratories, The University of Texas@Austin
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- *
- * Configuration settings for the utx8245 board.
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245 1
-#define CONFIG_UTX8245 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define DEBUG 1
-
-#define CONFIG_IDENT_STRING " [UTX5] "
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 57600
-
-#define CONFIG_BOOTDELAY 2
-#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay
-#define CONFIG_BOOTCOMMAND "run nfsboot" /* autoboot command */
-#define CONFIG_BOOTARGS "root=/dev/ram console=ttyS0,57600" /* RAMdisk */
-#define CONFIG_ETHADDR 00:AA:00:14:00:05 /* UTX5 */
-#define CONFIG_SERVERIP 10.8.17.105 /* Spree */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "kernel_addr=FFA00000\0" \
- "ramdisk_addr=FF800000\0" \
- "u-boot_startaddr=FFB00000\0" \
- "u-boot_endaddr=FFB2FFFF\0" \
- "nfsargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/nfs rw \
-nfsroot=${nfsrootip}:${rootpath} ip=dhcp\0" \
- "ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram0\0" \
- "smargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/mtdblock1 ro\0" \
- "fwargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/sda2 ro\0" \
- "nfsboot=run nfsargs;bootm ${kernel_addr}\0" \
- "ramboot=run ramargs;bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "smboot=run smargs;bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "fwboot=run fwargs;bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "update_u-boot=tftp ${loadaddr} /bdi2000/u-boot.bin;protect off \
-${u-boot_startaddr} ${u-boot_endaddr};era ${u-boot_startaddr} \
-${u-boot_endaddr};cp.b ${loadaddr} ${u-boot_startaddr} ${filesize};\
-protect on ${u-boot_startaddr} ${u-boot_endaddr}"
-
-#define CONFIG_ENV_OVERWRITE
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_DATE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-
-/*-----------------------------------------------------------------------
- * PCI configuration
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_EEPRO100_SROM_WRITE
-
-#define PCI_ENET0_IOADDR 0xF0000000
-#define PCI_ENET0_MEMADDR 0xF0000000
-
-#define PCI_FIREWIRE_IOADDR 0xF1000000
-#define PCI_FIREWIRE_MEMADDR 0xF1000000
-/*
-#define PCI_ENET0_IOADDR 0xFE000000
-#define PCI_ENET0_MEMADDR 0x80000000
-
-#define PCI_FIREWIRE_IOADDR 0x81000000
-#define PCI_FIREWIRE_MEMADDR 0x81000000
-*/
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 256MB */
-/*#define CONFIG_SYS_VERY_BIG_RAM 1 */
-
-/* FLASH_BASE is FF800000, with 4MB on RCS0, but the reset vector
- * is actually located at FFF00100. Therefore, U-Boot is
- * physically located at 0xFFB0_0000, but is also mirrored at
- * 0xFFF0_0000.
- */
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*#define CONFIG_SYS_DRAM_TEST 1 */
-#define CONFIG_SYS_MEMTEST_START 0x00003000 /* memtest works on 0...256 MB */
-#define CONFIG_SYS_MEMTEST_END 0x0ff8ffa7 /* in SDRAM, skips exception */
- /* vectors and U-Boot */
-
-
-/*--------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- *------------------------------------------------------------------*/
-#define CONFIG_SYS_INIT_DATA_SIZE 128 /* Size in bytes reserved for */
- /* initial data */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*--------------------------------------------------------------------
- * NS16550 Configuration
- *------------------------------------------------------------------*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#if (CONFIG_CONS_INDEX == 1 || CONFIG_CONS_INDEX == 2)
-# define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#else
-# define CONFIG_SYS_NS16550_CLK 33000000
-#endif
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-#define CONFIG_SYS_NS16550_COM3 0xFF000000
-#define CONFIG_SYS_NS16550_COM4 0xFF000008
-
-/*--------------------------------------------------------------------
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- *------------------------------------------------------------------*/
-
-#define CONFIG_SYS_CLK_FREQ 33000000
-
-/*#define CONFIG_SYS_ETH_DEV_FN 0x7800 */
-/*#define CONFIG_SYS_ETH_IOBASE 0x00104000 */
-
-/*--------------------------------------------------------------------
- * I2C Configuration
- *------------------------------------------------------------------*/
-#if 1
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#endif
-
-#define CONFIG_RTC_PCF8563 1 /* enable I2C support for */
- /* Philips PCF8563 RTC */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
-
-/*--------------------------------------------------------------------
- * Memory Control Configuration Register values
- * - see sec. 4.12 of MPC8245 UM
- *------------------------------------------------------------------*/
-
-/**** MCCR1 ****/
-#define CONFIG_SYS_ROMNAL 0
-#define CONFIG_SYS_ROMFAL 10 /* (tacc=70ns)*mem_freq - 2,
- mem_freq = 100MHz */
-
-#define CONFIG_SYS_BANK7_ROW 0 /* SDRAM bank 7-0 row address */
-#define CONFIG_SYS_BANK6_ROW 0 /* bit count */
-#define CONFIG_SYS_BANK5_ROW 0
-#define CONFIG_SYS_BANK4_ROW 0
-#define CONFIG_SYS_BANK3_ROW 0
-#define CONFIG_SYS_BANK2_ROW 0
-#define CONFIG_SYS_BANK1_ROW 2
-#define CONFIG_SYS_BANK0_ROW 2
-
-/**** MCCR2, refresh interval clock cycles ****/
-#define CONFIG_SYS_REFINT 480 /* 33 MHz SDRAM clock was 480 */
-
-/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
-#define CONFIG_SYS_BSTOPRE 1023 /* burst to precharge[0..9], */
- /* sets open page interval */
-
-/**** MCCR3 ****/
-#define CONFIG_SYS_REFREC 7 /* Refresh to activate interval, trc */
-
-/**** MCCR4 ****/
-#define CONFIG_SYS_PRETOACT 2 /* trp */
-#define CONFIG_SYS_ACTTOPRE 7 /* trcd + (burst length - 1) + trdl */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type, sequential */
-#define CONFIG_SYS_ACTORW 2 /* trcd min */
-#define CONFIG_SYS_DBUS_SIZE2 1 /* set for 8-bit RCS1, clear for 32,64 */
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 0 /* we don't need extended ROM space */
-#define CONFIG_SYS_REGDIMM 0
-
-/* calculate according to formula in sec. 6-22 of 8245 UM */
-#define CONFIG_SYS_PGMAX 50 /* how long the 8245 retains the */
- /* currently accessed page in memory */
- /* was 45 */
-
-#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note */
- /* bits 7,6, and 3-0 MUST be 0 */
-
-#if 0
-#define CONFIG_SYS_DLL_MAX_DELAY 0x04
-#else
-#define CONFIG_SYS_DLL_MAX_DELAY 0
-#endif
-#if 0 /* need for 33MHz SDRAM */
-#define CONFIG_SYS_DLL_EXTEND 0x80
-#else
-#define CONFIG_SYS_DLL_EXTEND 0
-#endif
-#define CONFIG_SYS_PCI_HOLD_DEL 0x20
-
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these values to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8245 user manual.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE/2 - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START CONFIG_SYS_MAX_RAM_SIZE/2
-#define CONFIG_SYS_BANK1_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK1_ENABLE 1
-#define CONFIG_SYS_BANK2_START 0x3ff00000 /* not available in this design */
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-/*--------------------------------------------------------------------*/
-/* 4.4 - Output Driver Control Register */
-/*--------------------------------------------------------------------*/
-#define CONFIG_SYS_ODCR 0xe5
-
-/*--------------------------------------------------------------------*/
-/* 4.8 - Error Handling Registers */
-/*-------------------------------CONFIG_SYS_SDMODE_BURSTLEN-------------------------------------*/
-#define CONFIG_SYS_ERRENR1 0x11 /* enable SDRAM refresh overflow error */
-
-/* SDRAM 0-256 MB */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-/*#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT) */
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in dcache */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_SDRAM_BASE + 0x10000000| BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* PCI memory */
-/*#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) */
-/*#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) */
-
-/*Flash, config addrs, etc. */
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE 0xFF800000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-
-/* NOTE: environment is not EMBEDDED in the u-boot code.
- It's stored in flash in its own separate sector. */
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-#if 1 /* AMD AM29LV033C */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */
-#define CONFIG_ENV_ADDR 0xFFBF0000 /* flash sector SA63 */
-#define CONFIG_ENV_SECT_SIZE (64*1024) /* Size of the Environment Sector */
-#else /* AMD AM29LV116D */
-#define CONFIG_SYS_MAX_FLASH_SECT 35 /* Max number of sectors in one bank */
-#define CONFIG_ENV_ADDR 0xFF9FA000 /* flash sector SA33 */
-#define CONFIG_ENV_SECT_SIZE (8*1024) /* Size of the Environment Sector */
-#endif /* #if */
-
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE /* Size of the Environment */
-#define CONFIG_ENV_OFFSET 0 /* starting right@the beginning */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#endif /* __CONFIG_H */
diff --git a/include/mpc824x.h b/include/mpc824x.h
deleted file mode 100644
index 31d6f69..0000000
--- a/include/mpc824x.h
+++ /dev/null
@@ -1,523 +0,0 @@
-/*
- * Copyright Rob Taylor, Flying Pig Systems Ltd. 2000.
- * Copyright (C) 2001, James Dougherty, jfd at cs.stanford.edu
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __MPC824X_H__
-#define __MPC824X_H__
-
-#include <config.h>
-
-/* CPU Types */
-#define CPU_TYPE_601 0x01 /* PPC 601 CPU */
-#define CPU_TYPE_602 0x02 /* PPC 602 CPU */
-#define CPU_TYPE_603 0x03 /* PPC 603 CPU */
-#define CPU_TYPE_603E 0x06 /* PPC 603e CPU */
-#define CPU_TYPE_603P 0x07 /* PPC 603p CPU */
-#define CPU_TYPE_604 0x04 /* PPC 604 CPU */
-#define CPU_TYPE_604E 0x09 /* PPC 604e CPU */
-#define CPU_TYPE_604R 0x0a /* PPC 604r CPU */
-#define CPU_TYPE_750 0x08 /* PPC 750 CPU */
-#define CPU_TYPE_8240 0x81 /* PPC 8240 CPU */
-#define CPU_TYPE_8245 0x8081 /* PPC 8245/8241 CPU */
-#define _CACHE_ALIGN_SIZE 32 /* cache line size */
-
-/* spr976 - DMISS data tlb miss address register
- * spr977 - DCMP data tlb miss compare register
- * spr978 - HASH1 PTEG1 address register
- * spr980 - HASH2 PTEG2 address register
- * IMISS - instruction tlb miss address register
- * ICMP - instruction TLB mis compare register
- * RPA - real page address register
- * HID0 - hardware implemntation register
- * HID2 - instruction address breakpoint register
- */
-
-/* Kahlua/MPC8240 defines */
-#define VEN_DEV_ID 0x00021057 /* Vendor and Dev. ID for MPC106 */
-#define KAHLUA_ID 0x00031057 /* Vendor & Dev Id for Kahlua's PCI */
-#define KAHLUA2_ID 0x00061057 /* 8245 is aka Kahlua-2 */
-#define BMC_BASE 0x80000000 /* Kahlua ID in PCI Memory space */
-#define CHRP_REG_ADDR 0xfec00000 /* MPC107 Config, Map B */
-#define CHRP_REG_DATA 0xfee00000 /* MPC107 Config, Map B */
-#define CHRP_ISA_MEM_PHYS 0xfd000000
-#define CHRP_ISA_MEM_BUS 0x00000000
-#define CHRP_ISA_MEM_SIZE 0x01000000
-#define CHRP_ISA_IO_PHYS 0xfe000000
-#define CHRP_ISA_IO_BUS 0x00000000
-#define CHRP_ISA_IO_SIZE 0x00800000
-#define CHRP_PCI_IO_PHYS 0xfe800000
-#define CHRP_PCI_IO_BUS 0x00800000
-#define CHRP_PCI_IO_SIZE 0x00400000
-#define CHRP_PCI_MEM_PHYS 0x80000000
-#define CHRP_PCI_MEM_BUS 0x80000000
-#define CHRP_PCI_MEM_SIZE 0x7d000000
-#define CHRP_PCI_MEMORY_PHYS 0x00000000
-#define CHRP_PCI_MEMORY_BUS 0x00000000
-#define CHRP_PCI_MEMORY_SIZE 0x40000000
-#define PREP_REG_ADDR 0x80000cf8 /* MPC107 Config, Map A */
-#define PREP_REG_DATA 0x80000cfc /* MPC107 Config, Map A */
-#define PREP_ISA_IO_PHYS 0x80000000
-#define PREP_ISA_IO_BUS 0x00000000
-#define PREP_ISA_IO_SIZE 0x00800000
-#define PREP_PCI_IO_PHYS 0x81000000
-#define PREP_PCI_IO_BUS 0x01000000
-#define PREP_PCI_IO_SIZE 0x3e800000
-#define PREP_PCI_MEM_PHYS 0xc0000000
-#define PREP_PCI_MEM_BUS 0x00000000
-#define PREP_PCI_MEM_SIZE 0x3f000000
-#define PREP_PCI_MEMORY_PHYS 0x00000000
-#define PREP_PCI_MEMORY_BUS 0x80000000
-#define PREP_PCI_MEMORY_SIZE 0x80000000
-#define MPC107_PCI_CMD 0x80000004 /* MPC107 PCI cmd reg */
-#define MPC107_PCI_STAT 0x80000006 /* MPC107 PCI status reg */
-#define PROC_INT1_ADR 0x800000a8 /* MPC107 Processor i/f cfg1 */
-#define PROC_INT2_ADR 0x800000ac /* MPC107 Processor i/f cfg2 */
-#define MEM_CONT1_ADR 0x800000f0 /* MPC107 Memory control config. 1 */
-#define MEM_CONT2_ADR 0x800000f4 /* MPC107 Memory control config. 2 */
-#define MEM_CONT3_ADR 0x800000f8 /* MPC107 Memory control config. 3 */
-#define MEM_CONT4_ADR 0x800000fc /* MPC107 Memory control config. 4 */
-#define MEM_ERREN1_ADR 0x800000c0 /* MPC107 Memory error enable 1 */
-#define MEM_START1_ADR 0x80000080 /* MPC107 Memory starting addr */
-#define MEM_START2_ADR 0x80000084 /* MPC107 Memory starting addr-lo */
-#define XMEM_START1_ADR 0x80000088 /* MPC107 Extended mem. start addr-hi*/
-#define XMEM_START2_ADR 0x8000008c /* MPC107 Extended mem. start addr-lo*/
-#define MEM_END1_ADR 0x80000090 /* MPC107 Memory ending address */
-#define MEM_END2_ADR 0x80000094 /* MPC107 Memory ending addr-lo */
-#define XMEM_END1_ADR 0x80000098 /* MPC107 Extended mem. end addrs-hi */
-#define XMEM_END2_ADR 0x8000009c /* MPC107 Extended mem. end addrs-lo*/
-#define OUT_DRV_CONT 0x80000073 /* MPC107 Output Driver Control reg */
-#define MEM_EN_ADR 0x800000a0 /* Memory bank enable */
-#define PAGE_MODE 0x800000a3 /* MPC107 Page Mode Counter/Timer */
-
-/*-----------------------------------------------------------------------
- * Exception offsets (PowerPC standard)
- */
-#define EXC_OFF_RESERVED0 0x0000 /* Reserved */
-#define EXC_OFF_SYS_RESET 0x0100 /* System reset */
-#define EXC_OFF_MACH_CHCK 0x0200 /* Machine Check */
-#define EXC_OFF_DATA_STOR 0x0300 /* Data Storage */
-#define EXC_OFF_INS_STOR 0x0400 /* Instruction Storage */
-#define EXC_OFF_EXTERNAL 0x0500 /* External */
-#define EXC_OFF_ALIGN 0x0600 /* Alignment */
-#define EXC_OFF_PROGRAM 0x0700 /* Program */
-#define EXC_OFF_FPUNAVAIL 0x0800 /* Floating-point Unavailable */
-#define EXC_OFF_DECR 0x0900 /* Decrementer */
-#define EXC_OFF_RESERVED1 0x0A00 /* Reserved */
-#define EXC_OFF_RESERVED2 0x0B00 /* Reserved */
-#define EXC_OFF_SYS_CALL 0x0C00 /* System Call */
-#define EXC_OFF_TRACE 0x0D00 /* Trace */
-#define EXC_OFF_FPUNASSIST 0x0E00 /* Floating-point Assist */
-
- /* 0x0E10 - 0x0FFF are marked reserved in The PowerPC Architecture book */
- /* these found in DINK code - may not apply to 8240*/
-#define EXC_OFF_PMI 0x0F00 /* Performance Monitoring Interrupt */
-#define EXC_OFF_VMXUI 0x0F20 /* VMX (AltiVec) Unavailable Interrupt */
-
- /* 0x1000 - 0x2FFF are implementation specific */
- /* these found in DINK code - may not apply to 8240 */
-#define EXC_OFF_ITME 0x1000 /* Instruction Translation Miss Exception */
-#define EXC_OFF_DLTME 0x1100 /* Data Load Translation Miss Exception */
-#define EXC_OFF_DSTME 0x1200 /* Data Store Translation Miss Exception */
-#define EXC_OFF_IABE 0x1300 /* Instruction Addr Breakpoint Exception */
-#define EXC_OFF_SMIE 0x1400 /* System Management Interrupt Exception */
-#define EXC_OFF_JMDDI 0x1600 /* Java Mode denorm detect Interr -- WTF??*/
-#define EXC_OFF_RMTE 0x2000 /* Run Mode or Trace Exception */
-
-#define _START_OFFSET EXC_OFF_SYS_RESET
-
-#define MAP_A_CONFIG_ADDR_HIGH 0x8000 /* Upper half of CONFIG_ADDR for Map A */
-#define MAP_A_CONFIG_ADDR_LOW 0x0CF8 /* Lower half of CONFIG_ADDR for Map A */
-#define MAP_A_CONFIG_DATA_HIGH 0x8000 /* Upper half of CONFIG_DAT for Map A */
-#define MAP_A_CONFIG_DATA_LOW 0x0CFC /* Lower half of CONFIG_DAT for Map A */
-#define MAP_B_CONFIG_ADDR_HIGH 0xfec0 /* Upper half of CONFIG_ADDR for Map B */
-#define MAP_B_CONFIG_ADDR_LOW 0x0000 /* Lower half of CONFIG_ADDR for Map B */
-#define MAP_B_CONFIG_DATA_HIGH 0xfee0 /* Upper half of CONFIG_DAT for Map B */
-#define MAP_B_CONFIG_DATA_LOW 0x0000 /* Lower half of CONFIG_DAT for Map B */
-
-
-#if defined(CONFIG_SYS_ADDR_MAP_A)
-#define CONFIG_ADDR_HIGH MAP_A_CONFIG_ADDR_HIGH /* Upper half of CONFIG_ADDR */
-#define CONFIG_ADDR_LOW MAP_A_CONFIG_ADDR_LOW /* Lower half of CONFIG_ADDR */
-#define CONFIG_DATA_HIGH MAP_A_CONFIG_DATA_HIGH /* Upper half of CONFIG_DAT */
-#define CONFIG_DATA_LOW MAP_A_CONFIG_DATA_LOW /* Lower half of CONFIG_DAT */
-#else /* Assume Map B, default */
-#define CONFIG_ADDR_HIGH MAP_B_CONFIG_ADDR_HIGH /* Upper half of CONFIG_ADDR */
-#define CONFIG_ADDR_LOW MAP_B_CONFIG_ADDR_LOW /* Lower half of CONFIG_ADDR */
-#define CONFIG_DATA_HIGH MAP_B_CONFIG_DATA_HIGH /* Upper half of CONFIG_DAT */
-#define CONFIG_DATA_LOW MAP_B_CONFIG_DATA_LOW /* Lower half of CONFIG_DAT */
-#endif
-
-#define CONFIG_ADDR (CONFIG_ADDR_HIGH << 16 | CONFIG_ADDR_LOW)
-
-#define CONFIG_DATA (CONFIG_DATA_HIGH << 16 | CONFIG_DATA_LOW)
-
-/* Macros to write to config registers. addr should be a constant in all cases */
-
-#define CONFIG_WRITE_BYTE( addr, data ) \
- __asm__ __volatile__( \
- " stwbrx %1, 0, %0\n \
- sync\n \
- stb %3, %4(%2)\n \
- sync " \
- : /* no output */ \
- : "r" (CONFIG_ADDR), "r" ((addr) & ~3), \
- "b" (CONFIG_DATA), "r" (data), \
- "n" ((addr) & 3));
-
-#define CONFIG_WRITE_HALFWORD( addr, data ) \
- __asm__ __volatile__( \
- " stwbrx %1, 0, %0\n \
- sync\n \
- sthbrx %3, %4, %2\n \
- sync " \
- : /* no output */ \
- : "r" (CONFIG_ADDR), "r" ((addr) & ~3), \
- "r" (CONFIG_DATA), "r" (data), \
- "b" ((addr) & 3));
-
-/* this assumes it's writeing on word boundaries*/
-#define CONFIG_WRITE_WORD( addr, data ) \
- __asm__ __volatile__( \
- " stwbrx %1, 0, %0\n \
- sync\n \
- stwbrx %3, 0, %2\n \
- sync " \
- : /* no output */ \
- : "r" (CONFIG_ADDR), "r" (addr), \
- "r" (CONFIG_DATA), "r" (data));
-
-/* Configuration register reads*/
-
-#define CONFIG_READ_BYTE( addr, reg ) \
- __asm__ ( \
- " stwbrx %1, 0, %2\n \
- sync\n \
- lbz %0, %4(%3)\n \
- sync " \
- : "=r" (reg) \
- : "r" ((addr) & ~3), "r" (CONFIG_ADDR), \
- "b" (CONFIG_DATA), "n" ((addr) & 3));
-
-
-#define CONFIG_READ_HALFWORD( addr, reg ) \
- __asm__ ( \
- " stwbrx %1, 0, %2\n \
- sync\n \
- lhbrx %0, %4, %3\n \
- sync " \
- : "=r" (reg) \
- : "r" ((addr) & ~3), "r" (CONFIG_ADDR), \
- "r" (CONFIG_DATA), \
- "b" ((addr) & 3));
-
-/* this assumes it's reading on word boundaries*/
-#define CONFIG_READ_WORD( addr, reg ) \
- __asm__ ( \
- " stwbrx %1, 0, %2\n \
- sync\n \
- lwbrx %0, 0, %3\n \
- sync " \
- : "=r" (reg) \
- : "r" (addr), "r" (CONFIG_ADDR),\
- "r" (CONFIG_DATA));
-
-/*
- * configuration register 'addresses'.
- * These are described in chaper 5 of the 8240 users manual.
- * Where the register has an abreviation in the manual, this has
- * been usaed here, otherwise a name in keeping with the norm has
- * been invented.
- * Note that some of these registers aren't documented in the manual.
- */
-
-#define PCICR 0x80000004 /* PCI Command Register */
-#define PCISR 0x80000006 /* PCI Status Register */
-#define REVID 0x80000008 /* CPU revision id */
-#define PIR 0x80000009 /* PCI Programming Interface Register */
-#define PBCCR 0x8000000b /* PCI Base Class Code Register */
-#define PCLSR 0x8000000c /* Processor Cache Line Size Register */
-#define PLTR 0x8000000d /* PCI Latancy Timer Register */
-#define PHTR 0x8000000e /* PCI Header Type Register */
-#define BISTCTRL 0x8000000f /* BIST Control */
-#define LMBAR 0x80000010 /* Local Base Address Register */
-#define PCSRBAR 0x80000014 /* PCSR Base Address Register */
-#define ILR 0x8000003c /* PCI Interrupt Line Register */
-#define IPR 0x8000003d /* Interrupt Pin Register */
-#define MINGNT 0x8000003e /* MIN GNI */
-#define MAXLAT 0x8000003f /* MAX LAT */
-#define PCIACR 0x80000046 /* PCI Arbiter Control Register */
-#define PMCR1 0x80000070 /* Power management config. 1 */
-#define PMCR2 0x80000072 /* Power management config. 2 */
-#define ODCR 0x80000073 /* Output Driver Control Register */
-#define CLKDCR 0x80000074 /* CLK Driver Control Register */
-#if defined(CONFIG_MPC8245) || defined(CONFIG_MPC8241)
-#define MIOCR1 0x80000076 /* Miscellaneous I/O Control Register 1 */
-#define MIOCR2 0x80000077 /* Miscellaneous I/O Control Register 2 */
-#endif
-#define EUMBBAR 0x80000078 /* Embedded Utilities Memory Block Base Address Register */
-#define EUMBBAR_VAL 0x80500000 /* PCI Relocation offset for EUMB region */
-#define EUMBSIZE 0x00100000 /* Size of EUMB region */
-
-#define MSAR1 0x80000080 /* Memory Starting Address Register 1 */
-#define MSAR2 0x80000084 /* Memory Starting Address Register 2 */
-#define EMSAR1 0x80000088 /* Extended Memory Starting Address Register 1*/
-#define EMSAR2 0x8000008c /* Extended Memory Starting Address Register 2*/
-#define MEAR1 0x80000090 /* Memory Ending Address Register 1 */
-#define MEAR2 0x80000094 /* Memory Ending Address Register 2 */
-#define EMEAR1 0x80000098 /* Extended Memory Ending Address Register 1 */
-#define EMEAR2 0x8000009c /* Extended Memory Ending Address Register 2 */
-#define MBER 0x800000a0 /* Memory bank Enable Register*/
-#define MPMR 0x800000a3 /* Memory Page Mode Register (stores PGMAX) */
-#define PICR1 0x800000a8 /* Processor Interface Configuration Register 1 */
-#define PICR2 0x800000ac /* Processor Interface Configuration Register 2 */
-#define ECCSBECR 0x800000b8 /* ECC Single-Bit Error Counter Register */
-#define ECCSBETR 0x800000b8 /* ECC Single-Bit Error Trigger Register */
-#define ERRENR1 0x800000c0 /* Error Enableing Register 1 */
-#define ERRENR2 0x800000c4 /* Error Enableing Register 2 */
-#define ERRDR1 0x800000c1 /* Error Detection Register 1 */
-#define IPBESR 0x800000c3 /* Internal Processor Error Status Register */
-#define ERRDR2 0x800000c5 /* Error Detection Register 2 */
-#define PBESR 0x800000c7 /* PCI Bus Error Status Register */
-#define PBEAR 0x800000c8 /* Processor/PCI Bus Error Status Register */
-#define AMBOR 0x800000e0 /* Address Map B Options Register */
-#define PCMBCR 0x800000e1 /* PCI/Memory Buffer Configuration */
-#define MCCR1 0x800000f0 /* Memory Control Configuration Register 1 */
-#define MCCR2 0x800000f4 /* Memory Control Configuration Register 2 */
-#define MCCR3 0x800000f8 /* Memory Control Configuration Register 3 */
-#define MCCR4 0x800000fc /* Memory Control Configuration Register 4 */
-
-/* some values for some of the above */
-
-#define PICR1_CF_APARK 0x00000008
-#define PICR1_LE_MODE 0x00000020
-#define PICR1_ST_GATH_EN 0x00000040
-#if defined(CONFIG_MPC8240)
-#define PICR1_EN_PCS 0x00000080 /* according to dink code, sets the 8240 to handle pci config space */
-#elif defined(CONFIG_MPC8245) || defined(CONFIG_MPC8241)
-#define PICR1_NO_BUSW_CK 0x00000080 /* no bus width check for flash writes */
-#define PICR1_DEC 0x00000100 /* Time Base enable on 8245/8241 */
-#define ERCR1 0x800000d0 /* Extended ROM Configuration Register 1 */
-#define ERCR2 0x800000d4 /* Extended ROM Configuration Register 2 */
-#define ERCR3 0x800000d8 /* Extended ROM Configuration Register 3 */
-#define ERCR4 0x800000dc /* Extended ROM Configuration Register 4 */
-#define MIOCR1 0x80000076 /* Miscellaneous I/O Control Register 1 */
-#define MIOCR1_ADR_X 0x80000074 /* Miscellaneous I/O Control Register 1 */
-#define MIOCR1_SHIFT 2
-#define MIOCR2 0x80000077 /* Miscellaneous I/O Control Register 2 */
-#define MIOCR2_ADR_X 0x80000074 /* Miscellaneous I/O Control Register 1 */
-#define MIOCR2_SHIFT 3
-#define ODCR_ADR_X 0x80000070 /* Output Driver Control register */
-#define ODCR_SHIFT 3
-#define PMCR2_ADR 0x80000072 /* Power Mgmnt Cfg 2 register */
-#define PMCR2_ADR_X 0x80000070
-#define PMCR2_SHIFT 3
-#define PMCR1_ADR 0x80000070 /* Power Mgmnt Cfg 1 reister */
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-#define PICR1_CF_DPARK 0x00000200
-#define PICR1_MCP_EN 0x00000800
-#define PICR1_FLASH_WR_EN 0x00001000
-#ifdef CONFIG_MPC8240
-#define PICR1_ADDRESS_MAP 0x00010000
-#define PIRC1_MSK 0xff000000
-#endif
-#define PICR1_PROC_TYPE_MSK 0x00060000
-#define PICR1_PROC_TYPE_603E 0x00040000
-#define PICR1_RCS0 0x00100000
-
-#define PICR2_CF_SNOOP_WS_MASK 0x000c0000
-#define PICR2_CF_SNOOP_WS_0WS 0x00000000
-#define PICR2_CF_SNOOP_WS_1WS 0x00040000
-#define PICR2_CF_SNOOP_WS_2WS 0x00080000
-#define PICR2_CF_SNOOP_WS_3WS 0x000c0000
-#define PICR2_CF_APHASE_WS_MASK 0x0000000c
-#define PICR2_CF_APHASE_WS_0WS 0x00000000
-#define PICR2_CF_APHASE_WS_1WS 0x00000004
-#define PICR2_CF_APHASE_WS_2WS 0x00000008
-#define PICR2_CF_APHASE_WS_3WS 0x0000000c
-
-#define MCCR1_ROMNAL_SHIFT 28
-#define MCCR1_ROMNAL_MSK 0xf0000000
-#define MCCR1_ROMFAL_SHIFT 23
-#define MCCR1_ROMFAL_MSK 0x0f800000
-#define MCCR1_DBUS_SIZE0 0x00400000
-#define MCCR1_BURST 0x00100000
-#define MCCR1_MEMGO 0x00080000
-#define MCCR1_SREN 0x00040000
-#if defined(CONFIG_MPC8240)
-#define MCCR1_RAM_TYPE 0x00020000
-#elif defined(CONFIG_MPC8245) || defined(CONFIG_MPC8241)
-#define MCCR1_SDRAM_EN 0x00020000
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-#define MCCR1_PCKEN 0x00010000
-#define MCCR1_BANK1ROW_SHIFT 2
-#define MCCR1_BANK2ROW_SHIFT 4
-#define MCCR1_BANK3ROW_SHIFT 6
-#define MCCR1_BANK4ROW_SHIFT 8
-#define MCCR1_BANK5ROW_SHIFT 10
-#define MCCR1_BANK6ROW_SHIFT 12
-#define MCCR1_BANK7ROW_SHIFT 14
-
-#define MCCR2_TS_WAIT_TIMER_MSK 0xe0000000
-#define MCCR2_TS_WAIT_TIMER_SHIFT 29
-#define MCCR2_ASRISE_MSK 0x1e000000
-#define MCCR2_ASRISE_SHIFT 25
-#define MCCR2_ASFALL_MSK 0x01e00000
-#define MCCR2_ASFALL_SHIFT 21
-
-#define MCCR2_INLINE_PAR_NOT_ECC 0x00100000
-#define MCCR2_WRITE_PARITY_CHK 0x00080000
-#define MCCR2_INLFRD_PARECC_CHK_EN 0x00040000
-#ifdef CONFIG_MPC8240
-#define MCCR2_ECC_EN 0x00020000
-#define MCCR2_EDO 0x00010000
-#endif
-#define MCCR2_REFINT_MSK 0x0000fffc
-#define MCCR2_REFINT_SHIFT 2
-#define MCCR2_RSV_PG 0x00000002
-#define MCCR2_PMW_PAR 0x00000001
-
-#define MCCR3_BSTOPRE2TO5_MSK 0xf0000000 /*BSTOPRE[2-5]*/
-#define MCCR3_BSTOPRE2TO5_SHIFT 28
-#define MCCR3_REFREC_MSK 0x0f000000
-#define MCCR3_REFREC_SHIFT 24
-#ifdef CONFIG_MPC8240
-#define MCCR3_RDLAT_MSK 0x00f00000
-#define MCCR3_RDLAT_SHIFT 20
-#define MCCR3_CPX 0x00010000
-#define MCCR3_RAS6P_MSK 0x00078000
-#define MCCR3_RAS6P_SHIFT 15
-#define MCCR3_CAS5_MSK 0x00007000
-#define MCCR3_CAS5_SHIFT 12
-#define MCCR3_CP4_MSK 0x00000e00
-#define MCCR3_CP4_SHIFT 9
-#define MCCR3_CAS3_MSK 0x000001c0
-#define MCCR3_CAS3_SHIFT 6
-#define MCCR3_RCD2_MSK 0x00000038
-#define MCCR3_RCD2_SHIFT 3
-#define MCCR3_RP1_MSK 0x00000007
-#define MCCR3_RP1_SHIFT 0
-#endif
-
-#define MCCR4_PRETOACT_MSK 0xf0000000
-#define MCCR4_PRETOACT_SHIFT 28
-#define MCCR4_ACTTOPRE_MSK 0x0f000000
-#define MCCR4_ACTTOPRE_SHIFT 24
-#define MCCR4_WMODE 0x00800000
-#define MCCR4_INLINE 0x00400000
-#if defined(CONFIG_MPC8240)
-#define MCCR4_BIT21 0x00200000 /* this include cos DINK code sets it- unknown function*/
-#elif defined(CONFIG_MPC8245) || defined(CONFIG_MPC8241)
-#define MCCR4_EXTROM 0x00200000 /* enables Extended ROM space */
-#else
-#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
-#endif
-#define MCCR4_REGISTERED 0x00100000
-#define MCCR4_BSTOPRE0TO1_MSK 0x000c0000 /*BSTOPRE[0-1]*/
-#define MCCR4_BSTOPRE0TO1_SHIFT 18
-#define MCCR4_REGDIMM 0x00008000
-#define MCCR4_SDMODE_MSK 0x00007f00
-#define MCCR4_SDMODE_SHIFT 8
-#define MCCR4_ACTTORW_MSK 0x000000f0
-#define MCCR4_ACTTORW_SHIFT 4
-#define MCCR4_BSTOPRE6TO9_MSK 0x0000000f /*BSTOPRE[6-9]*/
-#define MCCR4_BSTOPRE6TO9_SHIFT 0
-#define MCCR4_DBUS_SIZE2_SHIFT 17
-
-#define MICR_ADDR_MASK 0x0ff00000
-#define MICR_ADDR_SHIFT 20
-#define MICR_EADDR_MASK 0x30000000
-#define MICR_EADDR_SHIFT 28
-
-/*eumb and epic config*/
-
-#define EPIC_FPR 0x00041000
-#define EPIC_GCR 0x00041020
-#define EPIC_EICR 0x00041030
-#define EPIC_EVI 0x00041080
-#define EPIC_PI 0x00041090
-#define EPIC_SVR 0x000410E0
-#define EPIC_TFRR 0x000410F0
-
-/*
- * Note the information for these is rather mangled in the 8240 manual.
- * These are guesses.
- */
-
-#define EPIC_GTCCR0 0x00041100
-#define EPIC_GTCCR1 0x00041140
-#define EPIC_GTCCR2 0x00041180
-#define EPIC_GTCCR3 0x000411C0
-#define EPIC_GTBCR0 0x00041110
-#define EPIC_GTBCR1 0x00041150
-#define EPIC_GTBCR2 0x00041190
-#define EPIC_GTBCR3 0x000411D0
-#define EPIC_GTVPR0 0x00041120
-#define EPIC_GTVPR1 0x00041160
-#define EPIC_GTVPR2 0x000411a0
-#define EPIC_GTVPR3 0x000411e0
-#define EPIC_GTDR0 0x00041130
-#define EPIC_GTDR1 0x00041170
-#define EPIC_GTDR2 0x000411b0
-#define EPIC_GTDR3 0x000411f0
-
-#define EPIC_IVPR0 0x00050200
-#define EPIC_IVPR1 0x00050220
-#define EPIC_IVPR2 0x00050240
-#define EPIC_IVPR3 0x00050260
-#define EPIC_IVPR4 0x00050280
-
-#define EPIC_SVPR0 0x00050200
-#define EPIC_SVPR1 0x00050220
-#define EPIC_SVPR2 0x00050240
-#define EPIC_SVPR3 0x00050260
-#define EPIC_SVPR4 0x00050280
-#define EPIC_SVPR5 0x000502A0
-#define EPIC_SVPR6 0x000502C0
-#define EPIC_SVPR7 0x000502E0
-#define EPIC_SVPR8 0x00050300
-#define EPIC_SVPR9 0x00050320
-#define EPIC_SVPRa 0x00050340
-#define EPIC_SVPRb 0x00050360
-#define EPIC_SVPRc 0x00050380
-#define EPIC_SVPRd 0x000503A0
-#define EPIC_SVPRe 0x000503C0
-#define EPIC_SVPRf 0x000503E0
-
-/* MPC8240 Byte Swap/PCI Support Macros */
-#define BYTE_SWAP_16_BIT(x) ( (((x) & 0x00ff) << 8) | ( (x) >> 8) )
-#define LONGSWAP(x) ((((x) & 0x000000ff) << 24) | (((x) & 0x0000ff00) << 8)|\
- (((x) & 0x00ff0000) >> 8) | (((x) & 0xff000000) >> 24) )
-#define PCISWAP(x) LONGSWAP(x)
-
-#ifndef __ASSEMBLY__
-
-/*
- * MPC107 Support
- *
- */
-unsigned int mpc824x_mpc107_getreg(unsigned int regNum);
-void mpc824x_mpc107_setreg(unsigned int regNum, unsigned int regVal);
-void mpc824x_mpc107_write8(unsigned int address, unsigned char data);
-void mpc824x_mpc107_write16(unsigned int address, unsigned short data);
-void mpc824x_mpc107_write32(unsigned int address, unsigned int data);
-unsigned char mpc824x_mpc107_read8(unsigned int address);
-unsigned short mpc824x_mpc107_read16(unsigned int address);
-unsigned int mpc824x_mpc107_read32(unsigned int address);
-unsigned int mpc824x_eummbar_read(unsigned int regNum);
-void mpc824x_eummbar_write(unsigned int regNum, unsigned int regVal);
-
-#ifdef CONFIG_PCI
-struct pci_controller;
-void pci_cpm824x_init(struct pci_controller* hose);
-#endif
-
-#endif /* __ASSEMBLY__ */
-
-#endif /* __MPC824X_H__ */
diff --git a/include/pci.h b/include/pci.h
index 216f448..7f67ca6 100644
--- a/include/pci.h
+++ b/include/pci.h
@@ -670,10 +670,6 @@ extern void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
const char * pci_class_str(u8 class);
int pci_last_busno(void);
-#ifdef CONFIG_MPC824X
-extern void pci_mpc824x_init (struct pci_controller *hose);
-#endif
-
#ifdef CONFIG_MPC85xx
extern void pci_mpc85xx_init (struct pci_controller *hose);
#endif
diff --git a/include/pcmcia/cirrus.h b/include/pcmcia/cirrus.h
deleted file mode 100644
index cd34dd8..0000000
--- a/include/pcmcia/cirrus.h
+++ /dev/null
@@ -1,180 +0,0 @@
-/*
- * cirrus.h 1.4 1999/10/25 20:03:34
- *
- * The contents of this file are subject to the Mozilla Public License
- * Version 1.1 (the "License"); you may not use this file except in
- * compliance with the License. You may obtain a copy of the License
- * at http://www.mozilla.org/MPL/
- *
- * Software distributed under the License is distributed on an "AS IS"
- * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
- * the License for the specific language governing rights and
- * limitations under the License.
- *
- * The initial developer of the original code is David A. Hinds
- * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
- * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
- *
- * Alternatively, the contents of this file may be used under the
- * terms of the GNU General Public License version 2 (the "GPL"), in which
- * case the provisions of the GPL are applicable instead of the
- * above. If you wish to allow the use of your version of this file
- * only under the terms of the GPL and not to allow others to use
- * your version of this file under the MPL, indicate your decision by
- * deleting the provisions above and replace them with the notice and
- * other provisions required by the GPL. If you do not delete the
- * provisions above, a recipient may use your version of this file
- * under either the MPL or the GPL.
- */
-
-#ifndef _LINUX_CIRRUS_H
-#define _LINUX_CIRRUS_H
-
-#ifndef PCI_VENDOR_ID_CIRRUS
-#define PCI_VENDOR_ID_CIRRUS 0x1013
-#endif
-#ifndef PCI_DEVICE_ID_CIRRUS_6729
-#define PCI_DEVICE_ID_CIRRUS_6729 0x1100
-#endif
-#ifndef PCI_DEVICE_ID_CIRRUS_6832
-#define PCI_DEVICE_ID_CIRRUS_6832 0x1110
-#endif
-
-#define PD67_MISC_CTL_1 0x16 /* Misc control 1 */
-#define PD67_FIFO_CTL 0x17 /* FIFO control */
-#define PD67_MISC_CTL_2 0x1E /* Misc control 2 */
-#define PD67_CHIP_INFO 0x1f /* Chip information */
-#define PD67_ATA_CTL 0x026 /* 6730: ATA control */
-#define PD67_EXT_INDEX 0x2e /* Extension index */
-#define PD67_EXT_DATA 0x2f /* Extension data */
-
-/* PD6722 extension registers -- indexed in PD67_EXT_INDEX */
-#define PD67_DATA_MASK0 0x01 /* Data mask 0 */
-#define PD67_DATA_MASK1 0x02 /* Data mask 1 */
-#define PD67_DMA_CTL 0x03 /* DMA control */
-
-/* PD6730 extension registers -- indexed in PD67_EXT_INDEX */
-#define PD67_EXT_CTL_1 0x03 /* Extension control 1 */
-#define PD67_MEM_PAGE(n) ((n)+5) /* PCI window bits 31:24 */
-#define PD67_EXTERN_DATA 0x0a
-#define PD67_MISC_CTL_3 0x25
-#define PD67_SMB_PWR_CTL 0x26
-
-/* I/O window address offset */
-#define PD67_IO_OFF(w) (0x36+((w)<<1))
-
-/* Timing register sets */
-#define PD67_TIME_SETUP(n) (0x3a + 3*(n))
-#define PD67_TIME_CMD(n) (0x3b + 3*(n))
-#define PD67_TIME_RECOV(n) (0x3c + 3*(n))
-
-/* Flags for PD67_MISC_CTL_1 */
-#define PD67_MC1_5V_DET 0x01 /* 5v detect */
-#define PD67_MC1_MEDIA_ENA 0x01 /* 6730: Multimedia enable */
-#define PD67_MC1_VCC_3V 0x02 /* 3.3v Vcc */
-#define PD67_MC1_PULSE_MGMT 0x04
-#define PD67_MC1_PULSE_IRQ 0x08
-#define PD67_MC1_SPKR_ENA 0x10
-#define PD67_MC1_INPACK_ENA 0x80
-
-/* Flags for PD67_FIFO_CTL */
-#define PD67_FIFO_EMPTY 0x80
-
-/* Flags for PD67_MISC_CTL_2 */
-#define PD67_MC2_FREQ_BYPASS 0x01
-#define PD67_MC2_DYNAMIC_MODE 0x02
-#define PD67_MC2_SUSPEND 0x04
-#define PD67_MC2_5V_CORE 0x08
-#define PD67_MC2_LED_ENA 0x10 /* IRQ 12 is LED enable */
-#define PD67_MC2_FAST_PCI 0x10 /* 6729: PCI bus > 25 MHz */
-#define PD67_MC2_3STATE_BIT7 0x20 /* Floppy change bit */
-#define PD67_MC2_DMA_MODE 0x40
-#define PD67_MC2_IRQ15_RI 0x80 /* IRQ 15 is ring enable */
-
-/* Flags for PD67_CHIP_INFO */
-#define PD67_INFO_SLOTS 0x20 /* 0 = 1 slot, 1 = 2 slots */
-#define PD67_INFO_CHIP_ID 0xc0
-#define PD67_INFO_REV 0x1c
-
-/* Fields in PD67_TIME_* registers */
-#define PD67_TIME_SCALE 0xc0
-#define PD67_TIME_SCALE_1 0x00
-#define PD67_TIME_SCALE_16 0x40
-#define PD67_TIME_SCALE_256 0x80
-#define PD67_TIME_SCALE_4096 0xc0
-#define PD67_TIME_MULT 0x3f
-
-/* Fields in PD67_DMA_CTL */
-#define PD67_DMA_MODE 0xc0
-#define PD67_DMA_OFF 0x00
-#define PD67_DMA_DREQ_INPACK 0x40
-#define PD67_DMA_DREQ_WP 0x80
-#define PD67_DMA_DREQ_BVD2 0xc0
-#define PD67_DMA_PULLUP 0x20 /* Disable socket pullups? */
-
-/* Fields in PD67_EXT_CTL_1 */
-#define PD67_EC1_VCC_PWR_LOCK 0x01
-#define PD67_EC1_AUTO_PWR_CLEAR 0x02
-#define PD67_EC1_LED_ENA 0x04
-#define PD67_EC1_INV_CARD_IRQ 0x08
-#define PD67_EC1_INV_MGMT_IRQ 0x10
-#define PD67_EC1_PULLUP_CTL 0x20
-
-/* Fields in PD67_MISC_CTL_3 */
-#define PD67_MC3_IRQ_MASK 0x03
-#define PD67_MC3_IRQ_PCPCI 0x00
-#define PD67_MC3_IRQ_EXTERN 0x01
-#define PD67_MC3_IRQ_PCIWAY 0x02
-#define PD67_MC3_IRQ_PCI 0x03
-#define PD67_MC3_PWR_MASK 0x0c
-#define PD67_MC3_PWR_SERIAL 0x00
-#define PD67_MC3_PWR_TI2202 0x08
-#define PD67_MC3_PWR_SMB 0x0c
-
-/* Register definitions for Cirrus PD6832 PCI-to-CardBus bridge */
-
-/* PD6832 extension registers -- indexed in PD67_EXT_INDEX */
-#define PD68_EXT_CTL_2 0x0b
-#define PD68_PCI_SPACE 0x22
-#define PD68_PCCARD_SPACE 0x23
-#define PD68_WINDOW_TYPE 0x24
-#define PD68_EXT_CSC 0x2e
-#define PD68_MISC_CTL_4 0x2f
-#define PD68_MISC_CTL_5 0x30
-#define PD68_MISC_CTL_6 0x31
-
-/* Extra flags in PD67_MISC_CTL_3 */
-#define PD68_MC3_HW_SUSP 0x10
-#define PD68_MC3_MM_EXPAND 0x40
-#define PD68_MC3_MM_ARM 0x80
-
-/* Bridge Control Register */
-#define PD6832_BCR_MGMT_IRQ_ENA 0x0800
-
-/* Socket Number Register */
-#define PD6832_SOCKET_NUMBER 0x004c /* 8 bit */
-
-
-typedef struct cirrus_state_t {
- u_char misc1, misc2;
- u_char timer[6];
-} cirrus_state_t;
-
-/* Cirrus options */
-static int has_dma = -1;
-static int has_led = -1;
-static int has_ring = -1;
-static int dynamic_mode = 0;
-static int freq_bypass = -1;
-#ifdef CONFIG_CPC45
-static int setup_time = 2;
-static int cmd_time = 6;
-static int recov_time = 1;
-#else
-static int setup_time = -1;
-static int cmd_time = -1;
-static int recov_time = -1;
-#endif
-
-
-#endif /* _LINUX_CIRRUS_H */
diff --git a/include/pcmcia/i82365.h b/include/pcmcia/i82365.h
deleted file mode 100644
index 0b432a8..0000000
--- a/include/pcmcia/i82365.h
+++ /dev/null
@@ -1,154 +0,0 @@
-/*
- * i82365.h 1.21 2001/08/24 12:15:33
- *
- * The contents of this file are subject to the Mozilla Public License
- * Version 1.1 (the "License"); you may not use this file except in
- * compliance with the License. You may obtain a copy of the License
- * at http://www.mozilla.org/MPL/
- *
- * Software distributed under the License is distributed on an "AS IS"
- * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
- * the License for the specific language governing rights and
- * limitations under the License.
- *
- * The initial developer of the original code is David A. Hinds
- * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
- * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
- *
- * Alternatively, the contents of this file may be used under the
- * terms of the GNU General Public License version 2 (the "GPL"), in
- * which case the provisions of the GPL are applicable instead of the
- * above. If you wish to allow the use of your version of this file
- * only under the terms of the GPL and not to allow others to use
- * your version of this file under the MPL, indicate your decision by
- * deleting the provisions above and replace them with the notice and
- * other provisions required by the GPL. If you do not delete the
- * provisions above, a recipient may use your version of this file
- * under either the MPL or the GPL.
- */
-
-#ifndef _LINUX_I82365_H
-#define _LINUX_I82365_H
-
-/* register definitions for the Intel 82365SL PCMCIA controller */
-
-/* Offsets for PCIC registers */
-#define I365_IDENT 0x00 /* Identification and revision */
-#define I365_STATUS 0x01 /* Interface status */
-#define I365_POWER 0x02 /* Power and RESETDRV control */
-#define I365_INTCTL 0x03 /* Interrupt and general control */
-#define I365_CSC 0x04 /* Card status change */
-#define I365_CSCINT 0x05 /* Card status change interrupt control */
-#define I365_ADDRWIN 0x06 /* Address window enable */
-#define I365_IOCTL 0x07 /* I/O control */
-#define I365_GENCTL 0x16 /* Card detect and general control */
-#define I365_GBLCTL 0x1E /* Global control register */
-
-/* Offsets for I/O and memory window registers */
-#define I365_IO(map) (0x08+((map)<<2))
-#define I365_MEM(map) (0x10+((map)<<3))
-#define I365_W_START 0
-#define I365_W_STOP 2
-#define I365_W_OFF 4
-
-/* Flags for I365_STATUS */
-#define I365_CS_BVD1 0x01
-#define I365_CS_STSCHG 0x01
-#define I365_CS_BVD2 0x02
-#define I365_CS_SPKR 0x02
-#define I365_CS_DETECT 0x0C
-#define I365_CS_WRPROT 0x10
-#define I365_CS_READY 0x20 /* Inverted */
-#define I365_CS_POWERON 0x40
-#define I365_CS_GPI 0x80
-
-/* Flags for I365_POWER */
-#define I365_PWR_OFF 0x00 /* Turn off the socket */
-#define I365_PWR_OUT 0x80 /* Output enable */
-#define I365_PWR_NORESET 0x40 /* Disable RESETDRV on resume */
-#define I365_PWR_AUTO 0x20 /* Auto pwr switch enable */
-#define I365_VCC_MASK 0x18 /* Mask for turning off Vcc */
-/* There are different layouts for B-step and DF-step chips: the B
- step has independent Vpp1/Vpp2 control, and the DF step has only
- Vpp1 control, plus 3V control */
-#define I365_VCC_5V 0x10 /* Vcc = 5.0v */
-#define I365_VCC_3V 0x18 /* Vcc = 3.3v */
-#define I365_VPP2_MASK 0x0c /* Mask for turning off Vpp2 */
-#define I365_VPP2_5V 0x04 /* Vpp2 = 5.0v */
-#define I365_VPP2_12V 0x08 /* Vpp2 = 12.0v */
-#define I365_VPP1_MASK 0x03 /* Mask for turning off Vpp1 */
-#define I365_VPP1_5V 0x01 /* Vpp2 = 5.0v */
-#define I365_VPP1_12V 0x02 /* Vpp2 = 12.0v */
-
-/* Flags for I365_INTCTL */
-#define I365_RING_ENA 0x80
-#define I365_PC_RESET 0x40
-#define I365_PC_IOCARD 0x20
-#define I365_INTR_ENA 0x10
-#define I365_IRQ_MASK 0x0F
-
-/* Flags for I365_CSC and I365_CSCINT*/
-#define I365_CSC_BVD1 0x01
-#define I365_CSC_STSCHG 0x01
-#define I365_CSC_BVD2 0x02
-#define I365_CSC_READY 0x04
-#define I365_CSC_DETECT 0x08
-#define I365_CSC_ANY 0x0F
-#define I365_CSC_GPI 0x10
-
-/* Flags for I365_ADDRWIN */
-#define I365_ADDR_MEMCS16 0x20
-#define I365_ENA_IO(map) (0x40 << (map))
-#define I365_ENA_MEM(map) (0x01 << (map))
-
-/* Flags for I365_IOCTL */
-#define I365_IOCTL_MASK(map) (0x0F << (map<<2))
-#define I365_IOCTL_WAIT(map) (0x08 << (map<<2))
-#define I365_IOCTL_0WS(map) (0x04 << (map<<2))
-#define I365_IOCTL_IOCS16(map) (0x02 << (map<<2))
-#define I365_IOCTL_16BIT(map) (0x01 << (map<<2))
-
-/* Flags for I365_GENCTL */
-#define I365_CTL_16DELAY 0x01
-#define I365_CTL_RESET 0x02
-#define I365_CTL_GPI_ENA 0x04
-#define I365_CTL_GPI_CTL 0x08
-#define I365_CTL_RESUME 0x10
-#define I365_CTL_SW_IRQ 0x20
-
-/* Flags for I365_GBLCTL */
-#define I365_GBL_PWRDOWN 0x01
-#define I365_GBL_CSC_LEV 0x02
-#define I365_GBL_WRBACK 0x04
-#define I365_GBL_IRQ_0_LEV 0x08
-#define I365_GBL_IRQ_1_LEV 0x10
-
-/* Flags for memory window registers */
-#define I365_MEM_16BIT 0x8000 /* In memory start high byte */
-#define I365_MEM_0WS 0x4000
-#define I365_MEM_WS1 0x8000 /* In memory stop high byte */
-#define I365_MEM_WS0 0x4000
-#define I365_MEM_WRPROT 0x8000 /* In offset high byte */
-#define I365_MEM_REG 0x4000
-
-#define I365_REG(slot, reg) (((slot) << 6) | (reg))
-
-/* Default ISA interrupt mask */
-#define I365_ISA_IRQ_MASK 0xdeb8 /* irq's 3-5,7,9-12,14,15 */
-
-/* Device ID's for PCI-to-PCMCIA bridges */
-
-#ifndef PCI_VENDOR_ID_INTEL
-#define PCI_VENDOR_ID_INTEL 0x8086
-#endif
-#ifndef PCI_DEVICE_ID_INTEL_82092AA_0
-#define PCI_DEVICE_ID_INTEL_82092AA_0 0x1221
-#endif
-#ifndef PCI_VENDOR_ID_OMEGA
-#define PCI_VENDOR_ID_OMEGA 0x119b
-#endif
-#ifndef PCI_DEVICE_ID_OMEGA_82C092G
-#define PCI_DEVICE_ID_OMEGA_82C092G 0x1221
-#endif
-
-#endif /* _LINUX_I82365_H */
diff --git a/include/pcmcia/ss.h b/include/pcmcia/ss.h
deleted file mode 100644
index aafae8a..0000000
--- a/include/pcmcia/ss.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * ss.h 1.31 2001/08/24 12:16:13
- *
- * The contents of this file are subject to the Mozilla Public License
- * Version 1.1 (the "License"); you may not use this file except in
- * compliance with the License. You may obtain a copy of the License
- * at http://www.mozilla.org/MPL/
- *
- * Software distributed under the License is distributed on an "AS IS"
- * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
- * the License for the specific language governing rights and
- * limitations under the License.
- *
- * The initial developer of the original code is David A. Hinds
- * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
- * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
- *
- * Alternatively, the contents of this file may be used under the
- * terms of the GNU General Public License version 2 (the "GPL"), in
- * which case the provisions of the GPL are applicable instead of the
- * above. If you wish to allow the use of your version of this file
- * only under the terms of the GPL and not to allow others to use
- * your version of this file under the MPL, indicate your decision by
- * deleting the provisions above and replace them with the notice and
- * other provisions required by the GPL. If you do not delete the
- * provisions above, a recipient may use your version of this file
- * under either the MPL or the GPL.
- */
-
-#ifndef _LINUX_SS_H
-#define _LINUX_SS_H
-
-/* For RegisterCallback */
-typedef struct ss_callback_t {
- void (*handler)(void *info, u_int events);
- void *info;
-} ss_callback_t;
-
-/* Definitions for card status flags for GetStatus */
-#define SS_WRPROT 0x0001
-#define SS_CARDLOCK 0x0002
-#define SS_EJECTION 0x0004
-#define SS_INSERTION 0x0008
-#define SS_BATDEAD 0x0010
-#define SS_BATWARN 0x0020
-#define SS_READY 0x0040
-#define SS_DETECT 0x0080
-#define SS_POWERON 0x0100
-#define SS_GPI 0x0200
-#define SS_STSCHG 0x0400
-#define SS_CARDBUS 0x0800
-#define SS_3VCARD 0x1000
-#define SS_XVCARD 0x2000
-#define SS_PENDING 0x4000
-
-/* for InquireSocket */
-typedef struct socket_cap_t {
- u_int features;
- u_int irq_mask;
- u_int map_size;
- u_char pci_irq;
- u_char cardbus;
- struct pci_bus *cb_bus;
- struct bus_operations *bus;
-} socket_cap_t;
-
-/* InquireSocket capabilities */
-#define SS_CAP_PAGE_REGS 0x0001
-#define SS_CAP_VIRTUAL_BUS 0x0002
-#define SS_CAP_MEM_ALIGN 0x0004
-#define SS_CAP_STATIC_MAP 0x0008
-#define SS_CAP_PCCARD 0x4000
-#define SS_CAP_CARDBUS 0x8000
-
-/* for GetSocket, SetSocket */
-typedef struct socket_state_t {
- u_int flags;
- u_int csc_mask;
- u_char Vcc, Vpp;
- u_char io_irq;
-} socket_state_t;
-
-/* Socket configuration flags */
-#define SS_PWR_AUTO 0x0010
-#define SS_IOCARD 0x0020
-#define SS_RESET 0x0040
-#define SS_DMA_MODE 0x0080
-#define SS_SPKR_ENA 0x0100
-#define SS_OUTPUT_ENA 0x0200
-#define SS_ZVCARD 0x0400
-
-/* Flags for I/O port and memory windows */
-#define MAP_ACTIVE 0x01
-#define MAP_16BIT 0x02
-#define MAP_AUTOSZ 0x04
-#define MAP_0WS 0x08
-#define MAP_WRPROT 0x10
-#define MAP_ATTRIB 0x20
-#define MAP_USE_WAIT 0x40
-#define MAP_PREFETCH 0x80
-
-/* Use this just for bridge windows */
-#define MAP_IOSPACE 0x20
-
-typedef struct pccard_io_map {
- u_char map;
- u_char flags;
- u_short speed;
- u_short start, stop;
-} pccard_io_map;
-
-typedef struct pccard_mem_map {
- u_char map;
- u_char flags;
- u_short speed;
- u_long sys_start, sys_stop;
- u_int card_start;
-} pccard_mem_map;
-
-typedef struct cb_bridge_map {
- u_char map;
- u_char flags;
- u_int start, stop;
-} cb_bridge_map;
-
-enum ss_service {
- SS_RegisterCallback, SS_InquireSocket,
- SS_GetStatus, SS_GetSocket, SS_SetSocket,
- SS_GetIOMap, SS_SetIOMap, SS_GetMemMap, SS_SetMemMap,
- SS_GetBridge, SS_SetBridge, SS_ProcSetup
-};
-
-#endif /* _LINUX_SS_H */
diff --git a/include/pcmcia/ti113x.h b/include/pcmcia/ti113x.h
deleted file mode 100644
index 5453588..0000000
--- a/include/pcmcia/ti113x.h
+++ /dev/null
@@ -1,234 +0,0 @@
-/*
- * ti113x.h 1.31 2002/05/12 18:19:47
- *
- * The contents of this file are subject to the Mozilla Public License
- * Version 1.1 (the "License"); you may not use this file except in
- * compliance with the License. You may obtain a copy of the License
- * at http://www.mozilla.org/MPL/
- *
- * Software distributed under the License is distributed on an "AS IS"
- * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
- * the License for the specific language governing rights and
- * limitations under the License.
- *
- * The initial developer of the original code is David A. Hinds
- * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
- * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
- *
- * Alternatively, the contents of this file may be used under the
- * terms of the GNU General Public License version 2 (the "GPL"), in
- * which case the provisions of the GPL are applicable instead of the
- * above. If you wish to allow the use of your version of this file
- * only under the terms of the GPL and not to allow others to use
- * your version of this file under the MPL, indicate your decision by
- * deleting the provisions above and replace them with the notice and
- * other provisions required by the GPL. If you do not delete the
- * provisions above, a recipient may use your version of this file
- * under either the MPL or the GPL.
- */
-
-#ifndef _LINUX_TI113X_H
-#define _LINUX_TI113X_H
-
-#ifndef PCI_VENDOR_ID_TI
-#define PCI_VENDOR_ID_TI 0x104c
-#endif
-
-#ifndef PCI_DEVICE_ID_TI_1130
-#define PCI_DEVICE_ID_TI_1130 0xac12
-#endif
-#ifndef PCI_DEVICE_ID_TI_1031
-#define PCI_DEVICE_ID_TI_1031 0xac13
-#endif
-#ifndef PCI_DEVICE_ID_TI_1131
-#define PCI_DEVICE_ID_TI_1131 0xac15
-#endif
-#ifndef PCI_DEVICE_ID_TI_1210
-#define PCI_DEVICE_ID_TI_1210 0xac1a
-#endif
-#ifndef PCI_DEVICE_ID_TI_1211
-#define PCI_DEVICE_ID_TI_1211 0xac1e
-#endif
-#ifndef PCI_DEVICE_ID_TI_1220
-#define PCI_DEVICE_ID_TI_1220 0xac17
-#endif
-#ifndef PCI_DEVICE_ID_TI_1221
-#define PCI_DEVICE_ID_TI_1221 0xac19
-#endif
-#ifndef PCI_DEVICE_ID_TI_1250A
-#define PCI_DEVICE_ID_TI_1250A 0xac16
-#endif
-#ifndef PCI_DEVICE_ID_TI_1225
-#define PCI_DEVICE_ID_TI_1225 0xac1c
-#endif
-#ifndef PCI_DEVICE_ID_TI_1251A
-#define PCI_DEVICE_ID_TI_1251A 0xac1d
-#endif
-#ifndef PCI_DEVICE_ID_TI_1251B
-#define PCI_DEVICE_ID_TI_1251B 0xac1f
-#endif
-#ifndef PCI_DEVICE_ID_TI_1410
-#define PCI_DEVICE_ID_TI_1410 0xac50
-#endif
-#ifndef PCI_DEVICE_ID_TI_1420
-#define PCI_DEVICE_ID_TI_1420 0xac51
-#endif
-#ifndef PCI_DEVICE_ID_TI_1450
-#define PCI_DEVICE_ID_TI_1450 0xac1b
-#endif
-#ifndef PCI_DEVICE_ID_TI_1451
-#define PCI_DEVICE_ID_TI_1451 0xac52
-#endif
-#ifndef PCI_DEVICE_ID_TI_1510
-#define PCI_DEVICE_ID_TI_1510 0xac56
-#endif
-#ifndef PCI_DEVICE_ID_TI_4410
-#define PCI_DEVICE_ID_TI_4410 0xac41
-#endif
-#ifndef PCI_DEVICE_ID_TI_4450
-#define PCI_DEVICE_ID_TI_4450 0xac40
-#endif
-#ifndef PCI_DEVICE_ID_TI_4451
-#define PCI_DEVICE_ID_TI_4451 0xac42
-#endif
-
-/* Register definitions for TI 113X PCI-to-CardBus bridges */
-
-/* System Control Register */
-#define TI113X_SYSTEM_CONTROL 0x80 /* 32 bit */
-#define TI113X_SCR_SMIROUTE 0x04000000
-#define TI113X_SCR_SMISTATUS 0x02000000
-#define TI113X_SCR_SMIENB 0x01000000
-#define TI113X_SCR_VCCPROT 0x00200000
-#define TI113X_SCR_REDUCEZV 0x00100000
-#define TI113X_SCR_CDREQEN 0x00080000
-#define TI113X_SCR_CDMACHAN 0x00070000
-#define TI113X_SCR_SOCACTIVE 0x00002000
-#define TI113X_SCR_PWRSTREAM 0x00000800
-#define TI113X_SCR_DELAYUP 0x00000400
-#define TI113X_SCR_DELAYDOWN 0x00000200
-#define TI113X_SCR_INTERROGATE 0x00000100
-#define TI113X_SCR_CLKRUN_SEL 0x00000080
-#define TI113X_SCR_PWRSAVINGS 0x00000040
-#define TI113X_SCR_SUBSYSRW 0x00000020
-#define TI113X_SCR_CB_DPAR 0x00000010
-#define TI113X_SCR_CDMA_EN 0x00000008
-#define TI113X_SCR_ASYNC_IRQ 0x00000004
-#define TI113X_SCR_KEEPCLK 0x00000002
-#define TI113X_SCR_CLKRUN_ENA 0x00000001
-
-#define TI122X_SCR_SER_STEP 0xc0000000
-#define TI122X_SCR_INTRTIE 0x20000000
-#define TI122X_SCR_P2CCLK 0x08000000
-#define TI122X_SCR_CBRSVD 0x00400000
-#define TI122X_SCR_MRBURSTDN 0x00008000
-#define TI122X_SCR_MRBURSTUP 0x00004000
-#define TI122X_SCR_RIMUX 0x00000001
-
-/* Multimedia Control Register */
-#define TI1250_MULTIMEDIA_CTL 0x84 /* 8 bit */
-#define TI1250_MMC_ZVOUTEN 0x80
-#define TI1250_MMC_PORTSEL 0x40
-#define TI1250_MMC_ZVEN1 0x02
-#define TI1250_MMC_ZVEN0 0x01
-
-#define TI1250_GENERAL_STATUS 0x85 /* 8 bit */
-#define TI1250_GPIO0_CONTROL 0x88 /* 8 bit */
-#define TI1250_GPIO1_CONTROL 0x89 /* 8 bit */
-#define TI1250_GPIO2_CONTROL 0x8a /* 8 bit */
-#define TI1250_GPIO3_CONTROL 0x8b /* 8 bit */
-#define TI12XX_IRQMUX 0x8c /* 32 bit */
-
-/* Retry Status Register */
-#define TI113X_RETRY_STATUS 0x90 /* 8 bit */
-#define TI113X_RSR_PCIRETRY 0x80
-#define TI113X_RSR_CBRETRY 0x40
-#define TI113X_RSR_TEXP_CBB 0x20
-#define TI113X_RSR_MEXP_CBB 0x10
-#define TI113X_RSR_TEXP_CBA 0x08
-#define TI113X_RSR_MEXP_CBA 0x04
-#define TI113X_RSR_TEXP_PCI 0x02
-#define TI113X_RSR_MEXP_PCI 0x01
-
-/* Card Control Register */
-#define TI113X_CARD_CONTROL 0x91 /* 8 bit */
-#define TI113X_CCR_RIENB 0x80
-#define TI113X_CCR_ZVENABLE 0x40
-#define TI113X_CCR_PCI_IRQ_ENA 0x20
-#define TI113X_CCR_PCI_IREQ 0x10
-#define TI113X_CCR_PCI_CSC 0x08
-#define TI113X_CCR_SPKROUTEN 0x02
-#define TI113X_CCR_IFG 0x01
-
-#define TI1220_CCR_PORT_SEL 0x20
-#define TI122X_CCR_AUD2MUX 0x04
-
-/* Device Control Register */
-#define TI113X_DEVICE_CONTROL 0x92 /* 8 bit */
-#define TI113X_DCR_5V_FORCE 0x40
-#define TI113X_DCR_3V_FORCE 0x20
-#define TI113X_DCR_IMODE_MASK 0x06
-#define TI113X_DCR_IMODE_ISA 0x02
-#define TI113X_DCR_IMODE_SERIAL 0x04
-
-#define TI12XX_DCR_IMODE_PCI_ONLY 0x00
-#define TI12XX_DCR_IMODE_ALL_SERIAL 0x06
-
-/* Buffer Control Register */
-#define TI113X_BUFFER_CONTROL 0x93 /* 8 bit */
-#define TI113X_BCR_CB_READ_DEPTH 0x08
-#define TI113X_BCR_CB_WRITE_DEPTH 0x04
-#define TI113X_BCR_PCI_READ_DEPTH 0x02
-#define TI113X_BCR_PCI_WRITE_DEPTH 0x01
-
-/* Diagnostic Register */
-#define TI1250_DIAGNOSTIC 0x93 /* 8 bit */
-#define TI1250_DIAG_TRUE_VALUE 0x80
-#define TI1250_DIAG_PCI_IREQ 0x40
-#define TI1250_DIAG_PCI_CSC 0x20
-#define TI1250_DIAG_ASYNC_CSC 0x01
-
-/* DMA Registers */
-#define TI113X_DMA_0 0x94 /* 32 bit */
-#define TI113X_DMA_1 0x98 /* 32 bit */
-
-/* ExCA IO offset registers */
-#define TI113X_IO_OFFSET(map) (0x36+((map)<<1))
-
-/* Data structure for tracking vendor-specific state */
-typedef struct ti113x_state_t {
- u32 sysctl; /* TI113X_SYSTEM_CONTROL */
- u8 cardctl; /* TI113X_CARD_CONTROL */
- u8 devctl; /* TI113X_DEVICE_CONTROL */
- u8 diag; /* TI1250_DIAGNOSTIC */
- u32 irqmux; /* TI12XX_IRQMUX */
-} ti113x_state_t;
-
-#define TI_PCIC_ID \
- IS_TI1130, IS_TI1131, IS_TI1031, IS_TI1210, IS_TI1211, \
- IS_TI1220, IS_TI1221, IS_TI1225, IS_TI1250A, IS_TI1251A, \
- IS_TI1251B, IS_TI1410, IS_TI1420, IS_TI1450, IS_TI1451, \
- IS_TI1510, IS_TI4410, IS_TI4450, IS_TI4451
-
-#define TI_PCIC_INFO \
- { "TI 1130", IS_TI|IS_CARDBUS, ID(TI, 1130) }, \
- { "TI 1131", IS_TI|IS_CARDBUS, ID(TI, 1131) }, \
- { "TI 1031", IS_TI|IS_CARDBUS, ID(TI, 1031) }, \
- { "TI 1210", IS_TI|IS_CARDBUS, ID(TI, 1210) }, \
- { "TI 1211", IS_TI|IS_CARDBUS, ID(TI, 1211) }, \
- { "TI 1220", IS_TI|IS_CARDBUS, ID(TI, 1220) }, \
- { "TI 1221", IS_TI|IS_CARDBUS, ID(TI, 1221) }, \
- { "TI 1225", IS_TI|IS_CARDBUS, ID(TI, 1225) }, \
- { "TI 1250A", IS_TI|IS_CARDBUS, ID(TI, 1250A) }, \
- { "TI 1251A", IS_TI|IS_CARDBUS, ID(TI, 1251A) }, \
- { "TI 1251B", IS_TI|IS_CARDBUS, ID(TI, 1251B) }, \
- { "TI 1410", IS_TI|IS_CARDBUS, ID(TI, 1410) }, \
- { "TI 1420", IS_TI|IS_CARDBUS, ID(TI, 1420) }, \
- { "TI 1450", IS_TI|IS_CARDBUS, ID(TI, 1450) }, \
- { "TI 1451", IS_TI|IS_CARDBUS, ID(TI, 1451) }, \
- { "TI 1510", IS_TI|IS_CARDBUS, ID(TI, 1510) }, \
- { "TI 4410", IS_TI|IS_CARDBUS, ID(TI, 4410) }, \
- { "TI 4450", IS_TI|IS_CARDBUS, ID(TI, 4450) }, \
- { "TI 4451", IS_TI|IS_CARDBUS, ID(TI, 4451) }
-
-#endif /* _LINUX_TI113X_H */
diff --git a/include/ppc_asm.tmpl b/include/ppc_asm.tmpl
index 5fcef9c..36d5975 100644
--- a/include/ppc_asm.tmpl
+++ b/include/ppc_asm.tmpl
@@ -80,7 +80,7 @@
#define r31 31
-#if defined(CONFIG_8xx) || defined(CONFIG_MPC824X)
+#if defined(CONFIG_8xx)
/* Some special registers */
@@ -92,7 +92,7 @@
#define LCTRL2 157 /* Load/Store Support (37-41) */
#define ICTRL 158
-#endif /* CONFIG_8xx, CONFIG_MPC824X */
+#endif /* CONFIG_8xx */
#if defined(CONFIG_5xx)
diff --git a/post/drivers/memory.c b/post/drivers/memory.c
index d94a437..d512fa5 100644
--- a/post/drivers/memory.c
+++ b/post/drivers/memory.c
@@ -170,7 +170,7 @@ DECLARE_GLOBAL_DATA_PTR;
*/
static void move64(const unsigned long long *src, unsigned long long *dest)
{
-#if defined(CONFIG_MPC8260) || defined(CONFIG_MPC824X)
+#if defined(CONFIG_MPC8260)
asm ("lfd 0, 0(3)\n\t" /* fpr0 = *scr */
"stfd 0, 0(4)" /* *dest = fpr0 */
: : : "fr0" ); /* Clobbers fr0 */
--
1.9.1
next prev parent reply other threads:[~2014-12-15 14:26 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-12-15 14:26 [U-Boot] [PATCH 0/26] Start removing non-generic boards Masahiro Yamada
2014-12-15 14:26 ` [U-Boot] [PATCH 01/26] mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 02/26] powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 03/26] mpc8xx: remove ELPT860 board support Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 04/26] mpc8xx: remove KUP4X, KUP4K " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 05/26] mpc8xx: remove SPD823TS " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 06/26] mpc8xx: remove RRvision " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 07/26] mpc8xx: remove R360MPI " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 08/26] mpc8xx: remove NETVIA " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 09/26] mpc8xx: remove lwmon " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 10/26] mpc8xx: remove IVMS8, IVML24 " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 11/26] mpc8xx: remove IP860 " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 12/26] mpc8xx: remove ESTEEM192E " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 13/26] powerpc: remove cogent_8xx, cogent_mpc8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 14/26] mpc8260: remove sacsng " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 15/26] mpc8260: remove ppmc8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 16/26] mpc8260: remove ep8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 17/26] mpc8260: remove VoVPN-GW " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 18/26] mpc8260: remove MPC8266ADS " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 19/26] mpc8260: remove PM825, PM826, PM828 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 20/26] mpc8260: remove muas3001 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 21/26] mpc8260: remove IPHASE4539 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 22/26] mpc8260: remove gw8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 23/26] mpc8260: remove ep82xxm " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 24/26] mpc8260: remove CPU86, CPU87 " Masahiro Yamada
2015-01-05 18:22 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 25/26] mpc8260: remove atc " Masahiro Yamada
2014-12-15 14:26 ` Masahiro Yamada [this message]
2014-12-15 16:46 ` [U-Boot] [PATCH 26/26] powerpc: mpc824x: remove MPC824X cpu support York Sun
2015-01-05 18:22 ` Tom Rini
2015-01-05 15:44 ` [U-Boot] [PATCH 0/26] Start removing non-generic boards Masahiro YAMADA
2015-01-05 18:28 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1418653608-14177-27-git-send-email-yamada.m@jp.panasonic.com \
--to=yamada.m@jp.panasonic.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.