[U-Boot] [PATCH 21/26] mpc8260: remove IPHASE4539 board support

[Masahiro Yamada <yamada.m@jp.panasonic.com>]

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Grandegger <wg@denx.de>
---

 arch/powerpc/cpu/mpc8260/Kconfig |   4 -
 board/iphase4539/Kconfig         |   9 -
 board/iphase4539/MAINTAINERS     |   6 -
 board/iphase4539/Makefile        |  10 -
 board/iphase4539/README          | 358 -----------------------------
 board/iphase4539/flash.c         | 474 ---------------------------------------
 board/iphase4539/iphase4539.c    | 408 ---------------------------------
 configs/IPHASE4539_defconfig     |   3 -
 doc/README.scrapyard             |   1 +
 include/configs/IPHASE4539.h     | 328 ---------------------------
 10 files changed, 1 insertion(+), 1600 deletions(-)
 delete mode 100644 board/iphase4539/Kconfig
 delete mode 100644 board/iphase4539/MAINTAINERS
 delete mode 100644 board/iphase4539/Makefile
 delete mode 100644 board/iphase4539/README
 delete mode 100644 board/iphase4539/flash.c
 delete mode 100644 board/iphase4539/iphase4539.c
 delete mode 100644 configs/IPHASE4539_defconfig
 delete mode 100644 include/configs/IPHASE4539.h

diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig
index 2b3c9c2..56b79ac 100644
--- a/arch/powerpc/cpu/mpc8260/Kconfig
+++ b/arch/powerpc/cpu/mpc8260/Kconfig
@@ -22,9 +22,6 @@ config TARGET_EP82XXM
 config TARGET_GW8260
 	bool "Support gw8260"
 
-config TARGET_IPHASE4539
-	bool "Support IPHASE4539"
-
 config TARGET_KM82XX
 	bool "Support km82xx"
 
@@ -35,7 +32,6 @@ source "board/cpu86/Kconfig"
 source "board/cpu87/Kconfig"
 source "board/ep82xxm/Kconfig"
 source "board/gw8260/Kconfig"
-source "board/iphase4539/Kconfig"
 source "board/keymile/km82xx/Kconfig"
 
 endmenu
diff --git a/board/iphase4539/Kconfig b/board/iphase4539/Kconfig
deleted file mode 100644
index 74594d2..0000000
--- a/board/iphase4539/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_IPHASE4539
-
-config SYS_BOARD
-	default "iphase4539"
-
-config SYS_CONFIG_NAME
-	default "IPHASE4539"
-
-endif
diff --git a/board/iphase4539/MAINTAINERS b/board/iphase4539/MAINTAINERS
deleted file mode 100644
index ddf6814..0000000
--- a/board/iphase4539/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-IPHASE4539 BOARD
-M:	Wolfgang Grandegger <wg@denx.de>
-S:	Maintained
-F:	board/iphase4539/
-F:	include/configs/IPHASE4539.h
-F:	configs/IPHASE4539_defconfig
diff --git a/board/iphase4539/Makefile b/board/iphase4539/Makefile
deleted file mode 100644
index 9197b84..0000000
--- a/board/iphase4539/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= iphase4539.o flash.o
diff --git a/board/iphase4539/README b/board/iphase4539/README
deleted file mode 100644
index c5146d9..0000000
--- a/board/iphase4539/README
+++ /dev/null
@@ -1,358 +0,0 @@
-
-This file contains basic information on the port of U-Boot to IPHASE4539
-(Interphase 4539 T1/E1/J1 PMC Communications Controller).
-All the changes fit in the common U-Boot infrastructure, providing a new
-IPHASE4539-specific entry in makefiles. To build U-Boot for IPHASE4539,
-type "make IPHASE4539_config", edit the "include/config_IPHASE4539.h"
-file if necessary, then type "make".
-
-
-Common file modifications:
---------------------------
-
-The following common files have been modified by this project:
-(starting from the ppcboot-1.1.5/ directory)
-
-MAKEALL				- IPHASE4539 entry added
-Makefile			- IPHASE4539_config entry added
-
-
-New files:
-----------
-
-The following new files have been added by this project:
-(starting from the ppcboot-1.1.5/ directory)
-
-board/iphase4539/		- board-specific directory
-board/iphase4539/Makefile	- board-specific makefile
-board/iphase4539/config.mk	- config file
-board/iphase4539/flash.c	- flash driver (for AM29LV033C)
-board/iphase4539/ppcboot.lds	- linker script
-board/iphase4539/iphase4539.c	- ioport and memory initialization
-include/config_IPHASE4539.h	- main configuration file
-
-
-New configuration options:
---------------------------
-
-CONFIG_IPHASE4539
-
-	Main board-specific option (should be defined for IPHASE4539).
-
-
-Acceptance criteria tests:
---------------------------
-
-The following tests have been conducted to validate the port of U-Boot
-to IPHASE4539:
-
-1. Operation on serial console:
-
-With SMC1 defined as console in the main configuration file, the U-Boot
-output appeared on the serial terminal connected to the 2.5mm stereo jack
-connector as follows:
-
-------------------------------------------------------------------------------
-=> help
-base    - print or set address offset
-bdinfo  - print Board Info structure
-bootm   - boot application image from memory
-bootp   - boot image via network using BootP/TFTP protocol
-bootd   - boot default, i.e., run 'bootcmd'
-cmp     - memory compare
-coninfo - print console devices and informations
-cp      - memory copy
-crc32   - checksum calculation
-dcache  - enable or disable data cache
-echo    - echo args to console
-erase   - erase FLASH memory
-flinfo  - print FLASH memory information
-go      - start application at address 'addr'
-help    - print online help
-icache  - enable or disable instruction cache
-iminfo  - print header information for application image
-loadb   - load binary file over serial line (kermit mode)
-loads   - load S-Record file over serial line
-loop    - infinite loop on address range
-md      - memory display
-mm      - memory modify (auto-incrementing)
-mtest   - simple RAM test
-mw      - memory write (fill)
-nm      - memory modify (constant address)
-printenv- print environment variables
-protect - enable or disable FLASH write protection
-rarpboot- boot image via network using RARP/TFTP protocol
-reset   - Perform RESET of the CPU
-run     - run commands in an environment variable
-saveenv - save environment variables to persistent storage
-setenv  - set environment variables
-sleep   - delay execution for some time
-source  - run script from memory
-tftpboot- boot image via network using TFTP protocol
-	       and env variables ipaddr and serverip
-version - print monitor version
-?       - alias for 'help'
-=>
-------------------------------------------------------------------------------
-
-
-2. Flash driver operation
-
-The following sequence was performed to test the "flinfo" command:
-
-------------------------------------------------------------------------------
-=> flinfo
-
-Bank # 1: AMD AM29LV033C (32 Mbit, uniform sectors)
-  Size: 4 MB in 64 Sectors
-  Sector Start Addresses:
-    FF800000 (RO) FF810000 (RO) FF820000      FF830000      FF840000
-    FF850000      FF860000      FF870000      FF880000      FF890000
-    FF8A0000      FF8B0000      FF8C0000      FF8D0000      FF8E0000
-    FF8F0000      FF900000      FF910000      FF920000      FF930000
-    FF940000      FF950000      FF960000      FF970000      FF980000
-    FF990000      FF9A0000      FF9B0000      FF9C0000      FF9D0000
-    FF9E0000      FF9F0000      FFA00000      FFA10000      FFA20000
-    FFA30000      FFA40000      FFA50000      FFA60000      FFA70000
-    FFA80000      FFA90000      FFAA0000      FFAB0000      FFAC0000
-    FFAD0000      FFAE0000      FFAF0000      FFB00000 (RO) FFB10000 (RO)
-    FFB20000 (RO) FFB30000 (RO) FFB40000      FFB50000      FFB60000
-    FFB70000      FFB80000      FFB90000      FFBA0000      FFBB0000
-    FFBC0000      FFBD0000      FFBE0000      FFBF0000
-------------------------------------------------------------------------------
-
-Note: the Hardware Configuration Word (HWC) of the 8260 is on the
-first sector of the flash and should not be touched. The U-Boot
-environment variables are stored on second sector and U-Boot
-starts at the address 0xFFB00000.
-
-
-The following sequence was performed to test the erase command:
-
-------------------------------------------------------------------------------
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78    ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78    |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5    ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78    H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=> erase ff880000 ff88ffff
-Erase Flash from 0xff880000 to 0xff88ffff
-.. done
-Erased 1 sectors
-=> md ff880000
-ff880000: ffffffff ffffffff ffffffff ffffffff    ................
-ff880010: ffffffff ffffffff ffffffff ffffffff    ................
-ff880020: ffffffff ffffffff ffffffff ffffffff    ................
-ff880030: ffffffff ffffffff ffffffff ffffffff    ................
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78    ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78    |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5    ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78    H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=> erase 1:8
-Erase Flash Sectors 8-8 in Bank # 1
-.. done
-=> md ff880000 20
-ff880000: ffffffff ffffffff ffffffff ffffffff    ................
-ff880010: ffffffff ffffffff ffffffff ffffffff    ................
-ff880020: ffffffff ffffffff ffffffff ffffffff    ................
-ff880030: ffffffff ffffffff ffffffff ffffffff    ................
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> cp 0 ff890000 10
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78    ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78    |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5    ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78    H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=> md ff890000
-ff890000: ff000000 60000000 60000000 7c7f1b78    ....`...`...|..x
-ff890010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78    |.#x|.+x|.3x|.;x
-ff890020: 3b000000 4811e0f5 48003719 480036a5    ;...H...H.7.H.6.
-ff890030: 480036f9 48003731 48005c5d 7c7a1b78    H.6.H.71H.\]|z.x
-ff890040: ffffffff ffffffff ffffffff ffffffff    ................
-ff890050: ffffffff ffffffff ffffffff ffffffff    ................
-ff890060: ffffffff ffffffff ffffffff ffffffff    ................
-ff890070: ffffffff ffffffff ffffffff ffffffff    ................
-=> erase 1:8-9
-Erase Flash Sectors 8-9 in Bank # 1
-.... done
-=> md ff880000 20
-ff880000: ffffffff ffffffff ffffffff ffffffff    ................
-ff880010: ffffffff ffffffff ffffffff ffffffff    ................
-ff880020: ffffffff ffffffff ffffffff ffffffff    ................
-ff880030: ffffffff ffffffff ffffffff ffffffff    ................
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=> md ff890000
-ff890000: ffffffff ffffffff ffffffff ffffffff    ................
-ff890010: ffffffff ffffffff ffffffff ffffffff    ................
-ff890020: ffffffff ffffffff ffffffff ffffffff    ................
-ff890030: ffffffff ffffffff ffffffff ffffffff    ................
-ff890040: ffffffff ffffffff ffffffff ffffffff    ................
-ff890050: ffffffff ffffffff ffffffff ffffffff    ................
-ff890060: ffffffff ffffffff ffffffff ffffffff    ................
-ff890070: ffffffff ffffffff ffffffff ffffffff    ................
-=>
-------------------------------------------------------------------------------
-
-
-The following sequence was performed to test the Flash programming commands:
-
-------------------------------------------------------------------------------
-=> erase ff880000 ff88ffff
-Erase Flash from 0xff880000 to 0xff88ffff
-.. done
-Erased 1 sectors
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> md 0 20
-00000000: ff000000 60000000 60000000 7c7f1b78    ....`...`...|..x
-00000010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78    |.#x|.+x|.3x|.;x
-00000020: 3b000000 4811e0f5 48003719 480036a5    ;...H...H.7.H.6.
-00000030: 480036f9 48003731 48005c5d 7c7a1b78    H.6.H.71H.\]|z.x
-00000040: 3c83c000 2c040000 40823378 7c0000a6    <...,...@.3x|...
-00000050: 60000030 7c1b03a6 3c00c000 600035ec    `..0|...<...`.5.
-00000060: 7c1a03a6 4c000064 00000000 00000000    |...L..d........
-00000070: 00000000 00000000 00000000 00000000    ................
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78    ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78    |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5    ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78    H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff    ................
-ff880050: ffffffff ffffffff ffffffff ffffffff    ................
-ff880060: ffffffff ffffffff ffffffff ffffffff    ................
-ff880070: ffffffff ffffffff ffffffff ffffffff    ................
-=>
-------------------------------------------------------------------------------
-
-
-The following sequence was performed to test storage of the environment
-variables in Flash:
-
-------------------------------------------------------------------------------
-=> setenv foo bar
-=> saveenv
-Un-Protected 1 sectors
-Erasing Flash...
-.. done
-Erased 1 sectors
-Saving Environment to Flash...
-Protected 1 sectors
-=> reset
-...
-=> printenv
-...
-foo=bar
-...
-Environment size: 339/65532 bytes
-=>
-------------------------------------------------------------------------------
-
-
-The following sequence was performed to test image download and run over
-Ethernet interface (both interfaces were tested):
-
-------------------------------------------------------------------------------
-=> tftpboot 40000 hello_world.bin
-ARP broadcast 1
-TFTP from server 10.0.0.1; our IP address is 10.0.0.8
-Filename 'hello_world.bin'.
-Load address: 0x40000
-Loading: #############
-done
-Bytes transferred = 65932 (1018c hex)
-=> go 40004
-## Starting application at 0x00040004 ...
-Hello World
-argc = 1
-argv[0] = "40004"
-argv[1] = "<NULL>"
-Hit any key to exit ...
-
-## Application terminated, rc = 0x0
-=>
-------------------------------------------------------------------------------
-
-
-3. Known Problems
-
-None for the moment.
-
-
-----------------------------------------------------------------------------
-U-Boot and Linux for Interphase 4539 T1/E1/J1 PMC Communications Controller
-----------------------------------------------------------------------------
-
-U-Boot:
-
-	Configure and make U-Boot:
-
-	$ cd <path>/u-boot
-	$ make IPHASE4539_config
-	$ make dep
-	$ make
-	$ cp -p u-boot.bin /tftpboot
-
-	Load u-boot.bin into the Flash memory at 0xffb00000.
-
-
-Linux:
-
-	Configure and make Linux:
-
-	$ cd <patch>/linux-2.4
-	$ make IPHASE4539_config
-	$ make oldconfig
-	$ make dep
-	$ make uImage
-	$ cp -p arch/powerpc/mbxboot/uImage /tftpboot
-
-	Load uImage via tftp and boot it.
-
-
-Flash organisation:
-
-	The following preliminary layout of the Flash memory
-	is defined:
-
-	0xff800000 (   0    -   64 kB): Hardware Configuration Word.
-	0xff810000 (  64 kB -  128 kB): U-Boot Environment.
-	0xff820000 ( 128 kB -    3 MB): RAMdisk.
-	0xffb00000 (   3 MB - 3328 kB): U-Boot.
-	0xffb40000 (3328 KB -    4 MB): Linux Kernel.
-
-
-For further information concerning U-Boot and Linux please consult
-the "DENX U-Boot and Linux Guide".
-
-
-(C) 2002 Wolfgang Grandegger, DENX Software Engineering, wg at denx.de
-===================================================================
diff --git a/board/iphase4539/flash.c b/board/iphase4539/flash.c
deleted file mode 100644
index 3c2dad6..0000000
--- a/board/iphase4539/flash.c
+++ /dev/null
@@ -1,474 +0,0 @@
-/*
- * (C) Copyright 2001
- * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
- *
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * Adapted for Interphase 4539 by Wolfgang Grandegger <wg@denx.de>.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <config.h>
-#include <common.h>
-#include <flash.h>
-#include <asm/io.h>
-
-flash_info_t	flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-extern int hwc_flash_size(void);
-static ulong flash_get_size (u32 addr, flash_info_t *info);
-static int flash_get_offsets (u32 base, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_reset (u32 addr);
-
-#define out8(a,v) *(volatile unsigned char*)(a) = v
-#define in8(a)	  *(volatile unsigned char*)(a)
-#define in32(a)	  *(volatile unsigned long*)(a)
-#define iobarrier_rw() eieio()
-
-unsigned long flash_init (void)
-{
-	unsigned int i;
-	unsigned long flash_size = 0;
-	unsigned long bank_size;
-	unsigned int bank = 0;
-
-	/* Init: no FLASHes known */
-	for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-		flash_info[i].sector_count = 0;
-		flash_info[i].size = 0;
-	}
-
-	/* Initialise the BOOT Flash */
-	if (bank == CONFIG_SYS_MAX_FLASH_BANKS) {
-		puts ("Warning: not all Flashes are initialised !");
-		return flash_size;
-	}
-
-	bank_size = flash_get_size (CONFIG_SYS_FLASH_BASE, flash_info + bank);
-	if (bank_size) {
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE && \
-    CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MAX_FLASH_SIZE
-		/* monitor protection ON by default */
-		flash_protect(FLAG_PROTECT_SET,
-			      CONFIG_SYS_MONITOR_BASE,
-			      CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
-			      flash_info + bank);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-		/* ENV protection ON by default */
-		flash_protect(FLAG_PROTECT_SET,
-			      CONFIG_ENV_ADDR,
-			      CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
-			      flash_info + bank);
-#endif
-
-		/* HWC protection ON by default */
-		flash_protect(FLAG_PROTECT_SET,
-			      CONFIG_SYS_FLASH_BASE,
-			      CONFIG_SYS_FLASH_BASE + 0x10000 - 1,
-			      flash_info + bank);
-
-		flash_size += bank_size;
-		bank++;
-	} else {
-		puts ("Warning: the BOOT Flash is not initialised !");
-	}
-
-	return flash_size;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (u32 addr, flash_info_t *info)
-{
-	volatile uchar value;
-#if 0
-	int i;
-#endif
-
-	/* Write auto select command: read Manufacturer ID */
-	out8(addr + 0x0555, 0xAA);
-	iobarrier_rw();
-	udelay(10);
-	out8(addr + 0x02AA, 0x55);
-	iobarrier_rw();
-	udelay(10);
-	out8(addr + 0x0555, 0x90);
-	iobarrier_rw();
-	udelay(10);
-
-	value = in8(addr);
-	iobarrier_rw();
-	udelay(10);
-	switch (value | (value << 16)) {
-	case AMD_MANUFACT:
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-
-	case FUJ_MANUFACT:
-		info->flash_id = FLASH_MAN_FUJ;
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		flash_reset (addr);
-		return 0;
-	}
-
-	value = in8(addr + 1);			/* device ID		*/
-	iobarrier_rw();
-
-	switch (value) {
-	case AMD_ID_LV033C:
-		info->flash_id += FLASH_AM033C;
-		info->size = hwc_flash_size();
-		if (info->size > CONFIG_SYS_MAX_FLASH_SIZE) {
-			printf("U-Boot supports only %d MB\n",
-			       CONFIG_SYS_MAX_FLASH_SIZE);
-			info->size = CONFIG_SYS_MAX_FLASH_SIZE;
-		}
-		info->sector_count = info->size / 0x10000;
-		break;				/* => 4 MB		*/
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		flash_reset (addr);
-		return (0);			/* => no or unknown flash */
-
-	}
-
-	if (!flash_get_offsets (addr, info)) {
-		flash_reset (addr);
-		return 0;
-	}
-
-#if 0
-	/* check for protected sectors */
-	for (i = 0; i < info->sector_count; i++) {
-		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
-		/* D0 = 1 if protected */
-		value = in8(info->start[i] + 2);
-		iobarrier_rw();
-		info->protect[i] = (value & 1) != 0;
-	}
-#endif
-
-	/*
-	 * Reset bank to read mode
-	 */
-	flash_reset (addr);
-
-	return (info->size);
-}
-
-static int flash_get_offsets (u32 base, flash_info_t *info)
-{
-	unsigned int i, size;
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AM033C:
-		/* set sector offsets for uniform sector type	*/
-		size = info->size / info->sector_count;
-		for (i = 0; i < info->sector_count; i++) {
-			info->start[i] = base + i * size;
-		}
-		break;
-	default:
-		return 0;
-	}
-
-	return 1;
-}
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	volatile u32 addr = info->start[0];
-	int flag, prot, sect, l_sect;
-	ulong start, now, last;
-
-	if (s_first < 0 || s_first > s_last) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (info->flash_id == FLASH_UNKNOWN ||
-	    info->flash_id > FLASH_AMD_COMP) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	out8(addr + 0x555, 0xAA);
-	iobarrier_rw();
-	out8(addr + 0x2AA, 0x55);
-	iobarrier_rw();
-	out8(addr + 0x555, 0x80);
-	iobarrier_rw();
-	out8(addr + 0x555, 0xAA);
-	iobarrier_rw();
-	out8(addr + 0x2AA, 0x55);
-	iobarrier_rw();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr = info->start[sect];
-			out8(addr, 0x30);
-			iobarrier_rw();
-			l_sect = sect;
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay (1000);
-
-	/*
-	 * We wait for the last triggered sector
-	 */
-	if (l_sect < 0)
-		goto DONE;
-
-	start = get_timer (0);
-	last  = start;
-	addr = info->start[l_sect];
-	while ((in8(addr) & 0x80) != 0x80) {
-		if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-			printf ("Timeout\n");
-			return 1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000) {	/* every second */
-			putc ('.');
-			last = now;
-		}
-		iobarrier_rw();
-	}
-
-DONE:
-	/* reset to read mode */
-	flash_reset (info->start[0]);
-
-	printf (" done\n");
-	return 0;
-}
-
-/*
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word(info, wp, data));
-}
-
-/*
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	volatile u32 addr = info->start[0];
-	ulong start;
-	int flag, i;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((in32(dest) & data) != data) {
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* first, perform an unlock bypass command to speed up flash writes */
-	out8(addr + 0x555, 0xAA);
-	iobarrier_rw();
-	out8(addr + 0x2AA, 0x55);
-	iobarrier_rw();
-	out8(addr + 0x555, 0x20);
-	iobarrier_rw();
-
-	/* write each byte out */
-	for (i = 0; i < 4; i++) {
-		char *data_ch = (char *)&data;
-		out8(addr, 0xA0);
-		iobarrier_rw();
-		out8(dest+i, data_ch[i]);
-		iobarrier_rw();
-		udelay(10); /* XXX */
-	}
-
-	/* we're done, now do an unlock bypass reset */
-	out8(addr, 0x90);
-	iobarrier_rw();
-	out8(addr, 0x00);
-	iobarrier_rw();
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	while ((in32(dest) & 0x80808080) != (data & 0x80808080)) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			return (1);
-		}
-		iobarrier_rw();
-	}
-
-	flash_reset (addr);
-
-	return (0);
-}
-
-/*
- * Reset bank to read mode
- */
-static void flash_reset (u32 addr)
-{
-	out8(addr, 0xF0);	/* reset bank */
-	iobarrier_rw();
-}
-
-void flash_print_info (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:	printf ("AMD ");		break;
-	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
-	case FLASH_MAN_BM:	printf ("BRIGHT MICRO ");	break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AM033C:	printf ("AM29LV033C (32 Mbit, uniform sectors)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	if (info->size % 0x100000 == 0) {
-		printf ("  Size: %ld MB in %d Sectors\n",
-			info->size / 0x100000, info->sector_count);
-	}
-	else if (info->size % 0x400 == 0) {
-		printf ("  Size: %ld KB in %d Sectors\n",
-			info->size / 0x400, info->sector_count);
-	}
-	else {
-		printf ("  Size: %ld B in %d Sectors\n",
-			info->size, info->sector_count);
-	}
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-}
diff --git a/board/iphase4539/iphase4539.c b/board/iphase4539/iphase4539.c
deleted file mode 100644
index d40d2b6..0000000
--- a/board/iphase4539/iphase4539.c
+++ /dev/null
@@ -1,408 +0,0 @@
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <asm/io.h>
-#include <asm/immap_8260.h>
-
-int hwc_flash_size (void);
-int hwc_local_sdram_size (void);
-int hwc_main_sdram_size (void);
-int hwc_serial_number (void);
-int hwc_mac_address (char *str);
-int hwc_manufact_date (char *str);
-int seeprom_read (int addr, uchar * data, int size);
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- *
- * The port definitions are taken from the old firmware (see
- * also SYS/H/4539.H):
- *
- *        ppar      psor        pdir       podr       pdat
- * PA: 0x02ffffff 0x02c00000 0xfc403fe6 0x00000000 0x02403fc0
- * PB: 0x0fffdeb0 0x000000b0 0x0f032347 0x00000000 0x0f000290
- * PC: 0x030ffa55 0x030f0040 0xbcf005ea 0x00000000 0xc0c0ba7d
- * PD: 0x09c04e3c 0x01000e3c 0x0a7ff1c3 0x00000000 0x00ce0ae9
- */
-const iop_conf_t iop_conf_tab[4][32] = {
-
-	/* Port A configuration */
-	{							/* conf ppar psor pdir podr pdat */
-	 {0, 1, 0, 0, 0, 0},		/* PA31 FCC1_TXENB  SLAVE */
-	 {0, 1, 0, 1, 0, 0},		/* PA30 FCC1_TXCLAV SLAVE */
-	 {0, 1, 0, 1, 0, 0},		/* PA29 FCC1_TXSOC */
-	 {0, 1, 0, 0, 0, 0},		/* PA28 FCC1_RXENB  SLAVE */
-	 {0, 1, 0, 0, 0, 0},		/* PA27 FCC1_RXSOC */
-	 {0, 1, 0, 1, 0, 0},		/* PA26 FCC1_RXCLAV SLAVE */
-	 {0, 1, 0, 1, 0, 1},		/* PA25 FCC1_TXD0 */
-	 {0, 1, 0, 1, 0, 1},		/* PA24 FCC1_TXD1 */
-	 {0, 1, 0, 1, 0, 1},		/* PA23 FCC1_TXD2 */
-	 {0, 1, 0, 1, 0, 1},		/* PA22 FCC1_TXD3 */
-	 {0, 1, 0, 1, 0, 1},		/* PA21 FCC1_TXD4 */
-	 {0, 1, 0, 1, 0, 1},		/* PA20 FCC1_TXD5 */
-	 {0, 1, 0, 1, 0, 1},		/* PA19 FCC1_TXD6 */
-	 {0, 1, 0, 1, 0, 1},		/* PA18 FCC1_TXD7 */
-	 {0, 1, 0, 0, 0, 0},		/* PA17 FCC1_RXD7 */
-	 {0, 1, 0, 0, 0, 0},		/* PA16 FCC1_RXD6 */
-	 {0, 1, 0, 0, 0, 0},		/* PA15 FCC1_RXD5 */
-	 {0, 1, 0, 0, 0, 0},		/* PA14 FCC1_RXD4 */
-	 {0, 1, 0, 0, 0, 0},		/* PA13 FCC1_RXD3 */
-	 {0, 1, 0, 0, 0, 0},		/* PA12 FCC1_RXD2 */
-	 {0, 1, 0, 0, 0, 0},		/* PA11 FCC1_RXD1 */
-	 {0, 1, 0, 0, 0, 0},		/* PA10 FCC1_RXD0 */
-	 {0, 1, 1, 1, 0, 1},		/* PA9  TDMA1_L1TXD */
-	 {0, 1, 1, 0, 0, 0},		/* PA8  TDMA1_L1RXD */
-	 {0, 0, 0, 0, 0, 0},		/* PA7  CONFIG0 */
-	 {0, 1, 1, 0, 0, 1},		/* PA6  TDMA1_L1RSYNC */
-	 {0, 0, 0, 1, 0, 0},		/* PA5  FCC2:RxAddr[2] */
-	 {0, 0, 0, 1, 0, 0},		/* PA4  FCC2:RxAddr[1] */
-	 {0, 0, 0, 1, 0, 0},		/* PA3  FCC2:RxAddr[0] */
-	 {0, 0, 0, 1, 0, 0},		/* PA2  FCC2:TxAddr[0] */
-	 {0, 0, 0, 1, 0, 0},		/* PA1  FCC2:TxAddr[1] */
-	 {0, 0, 0, 1, 0, 0}			/* PA0  FCC2:TxAddr[2] */
-	 },
-	/* Port B configuration */
-	{							/* conf ppar psor pdir podr pdat */
-	 {0, 0, 0, 1, 0, 0},		/* PB31 FCC2_RXSOC */
-	 {0, 0, 0, 1, 0, 0},		/* PB30 FCC2_TXSOC */
-	 {0, 0, 0, 1, 0, 0},		/* PB29 FCC2_RXCLAV */
-	 {0, 0, 0, 0, 0, 0},		/* PB28 CONFIG2 */
-	 {0, 1, 1, 0, 0, 1},		/* PB27 FCC2_TXD0 */
-	 {0, 1, 1, 0, 0, 0},		/* PB26 FCC2_TXD1 */
-	 {0, 0, 0, 1, 0, 0},		/* PB25 FCC2_TXD4 */
-	 {0, 1, 1, 0, 0, 1},		/* PB24 FCC2_TXD5 */
-	 {0, 0, 0, 1, 0, 0},		/* PB23 FCC2_TXD6 */
-	 {0, 1, 0, 1, 0, 1},		/* PB22 FCC2_TXD7 */
-	 {0, 1, 0, 0, 0, 0},		/* PB21 FCC2_RXD7 */
-	 {0, 1, 0, 0, 0, 0},		/* PB20 FCC2_RXD6 */
-	 {0, 1, 0, 0, 0, 0},		/* PB19 FCC2_RXD5 */
-	 {0, 0, 0, 1, 0, 0},		/* PB18 FCC2_RXD4 */
-	 {1, 1, 0, 0, 0, 0},		/* PB17 FCC3_RX_DV */
-	 {1, 1, 0, 0, 0, 0},		/* PB16 FCC3_RX_ER */
-	 {1, 1, 0, 1, 0, 0},		/* PB15 FCC3_TX_ER */
-	 {1, 1, 0, 1, 0, 0},		/* PB14 FCC3_TX_EN */
-	 {1, 1, 0, 0, 0, 0},		/* PB13 FCC3_COL */
-	 {1, 1, 0, 0, 0, 0},		/* PB12 FCC3_CRS */
-	 {1, 1, 0, 0, 0, 0},		/* PB11 FCC3_RXD3 */
-	 {1, 1, 0, 0, 0, 0},		/* PB10 FCC3_RXD2 */
-	 {1, 1, 0, 0, 0, 0},		/* PB9  FCC3_RXD1 */
-	 {1, 1, 0, 0, 0, 0},		/* PB8  FCC3_RXD0 */
-	 {1, 1, 0, 1, 0, 1},		/* PB7  FCC3_TXD0 */
-	 {1, 1, 0, 1, 0, 1},		/* PB6  FCC3_TXD1 */
-	 {1, 1, 0, 1, 0, 1},		/* PB5  FCC3_TXD2 */
-	 {1, 1, 0, 1, 0, 1},		/* PB4  FCC3_TXD3 */
-	 {0, 0, 0, 0, 0, 0},		/* PB3  */
-	 {0, 0, 0, 0, 0, 0},		/* PB2  */
-	 {0, 0, 0, 0, 0, 0},		/* PB1  */
-	 {0, 0, 0, 0, 0, 0},		/* PB0  */
-	 },
-	/* Port C configuration */
-	{							/* conf ppar psor pdir podr pdat */
-	 {0, 1, 0, 0, 0, 1},		/* PC31 CLK1 */
-	 {0, 0, 0, 1, 0, 0},		/* PC30 U1MASTER_N */
-	 {0, 1, 0, 0, 0, 1},		/* PC29 CLK3 */
-	 {0, 0, 0, 1, 0, 1},		/* PC28 -MT90220_RST */
-	 {0, 1, 0, 0, 0, 1},		/* PC27 CLK5 */
-	 {0, 0, 0, 1, 0, 1},		/* PC26 -QUADFALC_RST */
-	 {0, 1, 1, 1, 0, 1},		/* PC25 BRG4 */
-	 {1, 0, 0, 1, 0, 0},		/* PC24 MDIO */
-	 {1, 0, 0, 1, 0, 0},		/* PC23 MDC */
-	 {0, 1, 0, 0, 0, 1},		/* PC22 CLK10 */
-	 {0, 0, 0, 1, 0, 0},		/* PC21  */
-	 {0, 1, 0, 0, 0, 1},		/* PC20 CLK12 */
-	 {0, 1, 0, 0, 0, 1},		/* PC19 CLK13 */
-	 {1, 1, 0, 0, 0, 1},		/* PC18 CLK14 */
-	 {0, 1, 0, 0, 0, 0},		/* PC17 CLK15 */
-	 {1, 1, 0, 0, 0, 1},		/* PC16 CLK16 */
-	 {0, 1, 1, 0, 0, 0},		/* PC15 FCC1_TXADDR0 SLAVE */
-	 {0, 1, 1, 0, 0, 0},		/* PC14 FCC1_RXADDR0 SLAVE */
-	 {0, 1, 1, 0, 0, 0},		/* PC13 FCC1_TXADDR1 SLAVE */
-	 {0, 1, 1, 0, 0, 0},		/* PC12 FCC1_RXADDR1 SLAVE */
-	 {0, 0, 0, 1, 0, 0},		/* PC11 FCC2_RXD2 */
-	 {0, 0, 0, 1, 0, 0},		/* PC10 FCC2_RXD3 */
-	 {0, 0, 0, 1, 0, 1},		/* PC9  LTMODE */
-	 {0, 0, 0, 1, 0, 1},		/* PC8  SELSYNC */
-	 {0, 1, 1, 0, 0, 0},		/* PC7  FCC1_TXADDR2 SLAVE  */
-	 {0, 1, 1, 0, 0, 0},		/* PC6  FCC1_RXADDR2 SLAVE */
-	 {0, 0, 0, 1, 0, 0},		/* PC5  FCC2_TXCLAV MASTER */
-	 {0, 0, 0, 1, 0, 0},		/* PC4  FCC2_RXENB MASTER */
-	 {0, 0, 0, 1, 0, 0},		/* PC3  FCC2_TXD2 */
-	 {0, 0, 0, 1, 0, 0},		/* PC2  FCC2_TXD3 */
-	 {0, 0, 0, 0, 0, 1},		/* PC1  PTMC -PTEENB */
-	 {0, 0, 0, 1, 0, 1},		/* PC0  COMCLK_N */
-	 },
-	/* Port D configuration */
-	{							/* conf ppar psor pdir podr pdat */
-	 {0, 0, 0, 1, 0, 1},		/* PD31 -CAM_RST */
-	 {0, 0, 0, 1, 0, 0},		/* PD30 FCC2_TXENB */
-	 {0, 1, 1, 0, 0, 0},		/* PD29 FCC1_RXADDR3 SLAVE */
-	 {0, 1, 1, 0, 0, 1},		/* PD28 TDMC1_L1TXD */
-	 {0, 1, 1, 0, 0, 0},		/* PD27 TDMC1_L1RXD */
-	 {0, 1, 1, 0, 0, 1},		/* PD26 TDMC1_L1RSYNC */
-	 {0, 0, 0, 1, 0, 1},		/* PD25 LED0 -OFF */
-	 {0, 0, 0, 1, 0, 1},		/* PD24 LED5 -OFF */
-	 {1, 0, 0, 1, 0, 1},		/* PD23 -LXT971_RST */
-	 {0, 1, 1, 0, 0, 1},		/* PD22 TDMA2_L1TXD */
-	 {0, 1, 1, 0, 0, 0},		/* PD21 TDMA2_L1RXD */
-	 {0, 1, 1, 0, 0, 1},		/* PD20 TDMA2_L1RSYNC */
-	 {0, 0, 0, 1, 0, 0},		/* PD19 FCC2_TXADDR3 */
-	 {0, 0, 0, 1, 0, 0},		/* PD18 FCC2_RXADDR3 */
-	 {0, 1, 0, 1, 0, 0},		/* PD17 BRG2 */
-	 {0, 0, 0, 1, 0, 0},		/* PD16  */
-	 {0, 0, 0, 1, 0, 0},		/* PD15 PT2TO1 */
-	 {0, 0, 0, 1, 0, 1},		/* PD14 PT4TO3 */
-	 {0, 0, 0, 1, 0, 1},		/* PD13 -SWMODE */
-	 {0, 0, 0, 1, 0, 1},		/* PD12 -PTMODE */
-	 {0, 0, 0, 1, 0, 0},		/* PD11 FCC2_RXD0 */
-	 {0, 0, 0, 1, 0, 0},		/* PD10 FCC2_RXD1 */
-	 {1, 1, 0, 1, 0, 1},		/* PD9  SMC1_SMTXD */
-	 {1, 1, 0, 0, 0, 1},		/* PD8  SMC1_SMRXD */
-	 {0, 1, 1, 0, 0, 0},		/* PD7  FCC1_TXADDR3 SLAVE */
-	 {0, 0, 0, 1, 0, 0},		/* PD6  IMAMODE */
-	 {0, 0, 0, 0, 0, 0},		/* PD5  CONFIG2 */
-	 {0, 1, 0, 1, 0, 0},		/* PD4  BRG8 */
-	 {0, 0, 0, 0, 0, 0},		/* PD3  */
-	 {0, 0, 0, 0, 0, 0},		/* PD2  */
-	 {0, 0, 0, 0, 0, 0},		/* PD1  */
-	 {0, 0, 0, 0, 0, 0},		/* PD0  */
-	 }
-};
-
-phys_size_t initdram (int board_type)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8260_t *memctl = &immap->im_memctl;
-	volatile uchar *base;
-	ulong maxsize;
-	int i;
-
-	memctl->memc_psrt = CONFIG_SYS_PSRT;
-	memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
-#ifndef CONFIG_SYS_RAMBOOT
-	immap->im_siu_conf.sc_ppc_acr = 0x00000026;
-	immap->im_siu_conf.sc_ppc_alrh = 0x01276345;
-	immap->im_siu_conf.sc_ppc_alrl = 0x89ABCDEF;
-	immap->im_siu_conf.sc_lcl_acr = 0x00000000;
-	immap->im_siu_conf.sc_lcl_alrh = 0x01234567;
-	immap->im_siu_conf.sc_lcl_alrl = 0x89ABCDEF;
-	immap->im_siu_conf.sc_tescr1 = 0x00004000;
-	immap->im_siu_conf.sc_ltescr1 = 0x00004000;
-
-	/* Init Main SDRAM */
-#define OP_VALUE   0x404A241A
-#define OP_VALUE_M (OP_VALUE & 0x87FFFFFF);
-	base = (uchar *) CONFIG_SYS_SDRAM_BASE;
-	memctl->memc_psdmr = 0x28000000 | OP_VALUE_M;
-	*base = 0xFF;
-	memctl->memc_psdmr = 0x08000000 | OP_VALUE_M;
-	for (i = 0; i < 8; i++)
-		*base = 0xFF;
-	memctl->memc_psdmr = 0x18000000 | OP_VALUE_M;
-	*(base + 0x110) = 0xFF;
-	memctl->memc_psdmr = OP_VALUE;
-	memctl->memc_lsdmr = 0x4086A522;
-	*base = 0xFF;
-
-	/* We must be able to test a location outsize the maximum legal size
-	 * to find out THAT we are outside; but this address still has to be
-	 * mapped by the controller. That means, that the initial mapping has
-	 * to be (at least) twice as large as the maximum expected size.
-	 */
-	maxsize = (1 + (~memctl->memc_or1 | 0x7fff)) / 2;
-
-	maxsize = get_ram_size((long *)base, maxsize);
-
-	memctl->memc_or1 |= ~(maxsize - 1);
-
-	if (maxsize != hwc_main_sdram_size ())
-		printf ("Oops: memory test has not found all memory!\n");
-#endif
-
-	icache_enable ();
-	/* return total ram size of SDRAM */
-	return (maxsize);
-}
-
-int checkboard (void)
-{
-	char string[32];
-
-	hwc_manufact_date (string);
-
-	printf ("Board: Interphase 4539 (#%d %s)\n",
-		hwc_serial_number (),
-		string);
-
-#ifdef DEBUG
-	printf ("Manufacturing date: %s\n", string);
-	printf ("Serial number     : %d\n", hwc_serial_number ());
-	printf ("FLASH size        : %d MB\n", hwc_flash_size () >> 20);
-	printf ("Main SDRAM size   : %d MB\n", hwc_main_sdram_size () >> 20);
-	printf ("Local SDRAM size  : %d MB\n", hwc_local_sdram_size () >> 20);
-	hwc_mac_address (string);
-	printf ("MAC address       : %s\n", string);
-#endif
-
-	return 0;
-}
-
-int misc_init_r (void)
-{
-	char *s, str[32];
-	int num;
-
-	if ((s = getenv ("serial#")) == NULL &&
-		(num = hwc_serial_number ()) != -1) {
-		sprintf (str, "%06d", num);
-		setenv ("serial#", str);
-	}
-	if ((s = getenv ("ethaddr")) == NULL && hwc_mac_address (str) == 0) {
-		setenv ("ethaddr", str);
-	}
-	return (0);
-}
-
-/***************************************************************
- * We take some basic Hardware Configuration Parameter from the
- * Serial EEPROM conected to the PSpan bridge. We keep it as
- * simple as possible.
- */
-int hwc_flash_size (void)
-{
-	uchar byte;
-
-	if (!seeprom_read (0x40, &byte, sizeof (byte))) {
-		switch ((byte >> 2) & 0x3) {
-		case 0x1:
-			return 0x0400000;
-			break;
-		case 0x2:
-			return 0x0800000;
-			break;
-		case 0x3:
-			return 0x1000000;
-		default:
-			return 0x0100000;
-		}
-	}
-	return -1;
-}
-int hwc_local_sdram_size (void)
-{
-	uchar byte;
-
-	if (!seeprom_read (0x40, &byte, sizeof (byte))) {
-		switch ((byte & 0x03)) {
-		case 0x1:
-			return 0x0800000;
-		case 0x2:
-			return 0x1000000;
-		default:
-			return 0;			/* not present */
-		}
-	}
-	return -1;
-}
-int hwc_main_sdram_size (void)
-{
-	uchar byte;
-
-	if (!seeprom_read (0x41, &byte, sizeof (byte))) {
-		return 0x1000000 << ((byte >> 5) & 0x7);
-	}
-	return -1;
-}
-int hwc_serial_number (void)
-{
-	int sn = -1;
-
-	if (!seeprom_read (0xa0, (uchar *) &sn, sizeof (sn))) {
-		sn = cpu_to_le32 (sn);
-	}
-	return sn;
-}
-int hwc_mac_address (char *str)
-{
-	char mac[6];
-
-	if (!seeprom_read (0xb0, (uchar *)mac, sizeof (mac))) {
-		sprintf (str, "%02x:%02x:%02x:%02x:%02x:%02x\n",
-				 mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
-	} else {
-		strcpy (str, "ERROR");
-		return -1;
-	}
-	return 0;
-}
-int hwc_manufact_date (char *str)
-{
-	uchar byte;
-	int value;
-
-	if (seeprom_read (0x92, &byte, sizeof (byte)))
-		goto out;
-	value = byte;
-	if (seeprom_read (0x93, &byte, sizeof (byte)))
-		goto out;
-	value += byte << 8;
-	sprintf (str, "%02d/%02d/%04d",
-			 value & 0x1F, (value >> 5) & 0xF,
-			 1980 + ((value >> 9) & 0x1FF));
-	return 0;
-
-  out:
-	strcpy (str, "ERROR");
-	return -1;
-}
-
-#define PSPAN_ADDR      0xF0020000
-#define EEPROM_REG      0x408
-#define EEPROM_READ_CMD 0xA000
-#define PSPAN_WRITE(a,v) \
-    *((volatile unsigned long *)(PSPAN_ADDR+(a))) = v; eieio()
-#define PSPAN_READ(a) \
-    *((volatile unsigned long *)(PSPAN_ADDR+(a)))
-
-int seeprom_read (int addr, uchar * data, int size)
-{
-	ulong val, cmd;
-	int i;
-
-	for (i = 0; i < size; i++) {
-
-		cmd = EEPROM_READ_CMD;
-		cmd |= ((addr + i) << 24) & 0xff000000;
-
-		/* Wait for ACT to authorize write */
-		while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
-			eieio ();
-
-		/* Write command */
-		PSPAN_WRITE (EEPROM_REG, cmd);
-
-		/* Wait for data to be valid */
-		while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
-			eieio ();
-		/* Do it twice, first read might be erratic */
-		while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
-			eieio ();
-
-		/* Read error */
-		if (val & 0x00000040) {
-			return -1;
-		} else {
-			data[i] = (val >> 16) & 0xff;
-		}
-	}
-	return 0;
-}
diff --git a/configs/IPHASE4539_defconfig b/configs/IPHASE4539_defconfig
deleted file mode 100644
index d49ea52..0000000
--- a/configs/IPHASE4539_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_IPHASE4539=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7f76aae..af4b00c 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+IPHASE4539       powerpc     mpc8260        -           -           Wolfgang Grandegger <wg@denx.de>
 muas3001         powerpc     mpc8260        -           -           Heiko Schocher <hs@denx.de>
 PM825            powerpc     mpc8260        -           -           Wolfgang Denk <wd@denx.de>
 PM826            powerpc     mpc8260        -           -           Wolfgang Denk <wd@denx.de>
diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h
deleted file mode 100644
index e402075..0000000
--- a/include/configs/IPHASE4539.h
+++ /dev/null
@@ -1,328 +0,0 @@
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
- *
- * This file is based on similar values for other boards found in
- * other U-Boot config files, mainly tqm8260.h and mpc8260ads.h.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Config header file for a Interphase 4539 PMC, 64 MB SDRAM, 4MB Flash.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_IPHASE4539	1	/* ...on a Interphase 4539 PMC */
-
-#define	CONFIG_SYS_TEXT_BASE	0xffb00000
-
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-/*-----------------------------------------------------------------------
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#define	CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#undef	CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef	CONFIG_CONS_NONE		/* define if console on something else */
-#define CONFIG_CONS_INDEX	1	/* which serial channel for console */
-
-/*-----------------------------------------------------------------------
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC   */
-#define CONFIG_ETHER_ON_FCC		/* define if ether on FCC   */
-#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_INDEX	3	/* which channel for ether  */
-
-#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
-
-/*-----------------------------------------------------------------------
- * - Rx-CLK is CLK14
- * - Tx-CLK is CLK16
- * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
- */
-# define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK14 | CMXFCR_TF3CS_CLK16)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	0
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#endif	/* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-/* other options */
-
-#define CONFIG_8260_CLKIN	66666666	/* in Hz */
-#define CONFIG_BAUDRATE		19200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
-#define I2C_READ	((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00010000; \
-			else    iop->pdat &= ~0x00010000
-#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
-			else    iop->pdat &= ~0x00020000
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* autoboot command */
-#define CONFIG_BOOTARGS		"root=/dev/ram rw"
-
-#if defined(CONFIG_CMD_KGDB)
-#undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
-#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
-#endif
-
-#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)  /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00F00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passed to Linux in MHz */
-					/* for versions < 2.4.5-pre5	 */
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-#define CONFIG_SYS_RESET_ADDRESS	0x04400000
-
-#define CONFIG_MISC_INIT_R	1	/* We need misc_init_r()	*/
-
-/*-----------------------------------------------------------------------
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration (Setup by the
- * startup code). Please note that CONFIG_SYS_SDRAM_BASE _must_ start@0.
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFF800000
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)     /* Reserve 256 kB for Monitor  */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	64	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_SIZE	(CONFIG_SYS_MAX_FLASH_SECT * 0x10000)	/* 4 MB */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	2400000	/* Flash Erase Timeout (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
-
-/* Environment in FLASH, there is little space left in Serial EEPROM */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x10000 /* We use one complete sector	*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x10000) /* 2. sector */
-
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#define CONFIG_SYS_HRCW_MASTER ( ( HRCW_BPS01 | HRCW_EBM )		|\
-			  ( HRCW_L2CPC10 | HRCW_ISB110 )	|\
-			  ( HRCW_MMR11 | HRCW_APPC10 )		|\
-			  ( HRCW_CS10PC01 | HRCW_MODCK_H0101 )	 \
-			) /* 0x14863245 */
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000 /* We keep original value */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32     /* For MPC8260 CPU		*/
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT	5      /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers		2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
-			 HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL	(HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2	0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register					 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR		RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration					 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR		0xA01C0000
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				 4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR	0X4205C000
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined (CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control			 4-40
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_TMCNTSC	(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control					 9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR	0
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration				13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR	0
-
-/*-----------------------------------------------------------------------
- * Init Memory Controller:
- *
- * Bank Bus	Machine PortSz	Device
- * ---- ---	------- ------	------
- *  0	60x	GPCM	64 bit	FLASH
- *  1	60x	SDRAM	64 bit	SDRAM
- */
-
-#define CONFIG_SYS_BR0_PRELIM	((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) | 0x0801)
-#define CONFIG_SYS_OR0_PRELIM	0xFF800882
-#define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) | 0x0041)
-#define CONFIG_SYS_OR1_PRELIM	0xF8002CD0
-
-#define CONFIG_SYS_PSDMR	0x404A241A
-#define CONFIG_SYS_MPTPR	0x00007400
-#define CONFIG_SYS_PSRT	0x00000007
-
-#endif /* __CONFIG_H */
-- 
1.9.1