From: Masahiro Yamada <yamada.m@jp.panasonic.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 20/26] mpc8260: remove muas3001 board support
Date: Mon, 15 Dec 2014 23:26:25 +0900 [thread overview]
Message-ID: <1418653608-14177-21-git-send-email-yamada.m@jp.panasonic.com> (raw)
In-Reply-To: <1418653608-14177-1-git-send-email-yamada.m@jp.panasonic.com>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
---
arch/powerpc/cpu/mpc8260/Kconfig | 4 -
board/muas3001/Kconfig | 9 -
board/muas3001/MAINTAINERS | 7 -
board/muas3001/Makefile | 8 -
board/muas3001/muas3001.c | 335 ---------------------------------
configs/muas3001_defconfig | 3 -
configs/muas3001_dev_defconfig | 4 -
doc/README.scrapyard | 1 +
include/configs/muas3001.h | 391 ---------------------------------------
9 files changed, 1 insertion(+), 761 deletions(-)
delete mode 100644 board/muas3001/Kconfig
delete mode 100644 board/muas3001/MAINTAINERS
delete mode 100644 board/muas3001/Makefile
delete mode 100644 board/muas3001/muas3001.c
delete mode 100644 configs/muas3001_defconfig
delete mode 100644 configs/muas3001_dev_defconfig
delete mode 100644 include/configs/muas3001.h
diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig
index cb81cdc..2b3c9c2 100644
--- a/arch/powerpc/cpu/mpc8260/Kconfig
+++ b/arch/powerpc/cpu/mpc8260/Kconfig
@@ -25,9 +25,6 @@ config TARGET_GW8260
config TARGET_IPHASE4539
bool "Support IPHASE4539"
-config TARGET_MUAS3001
- bool "Support muas3001"
-
config TARGET_KM82XX
bool "Support km82xx"
@@ -40,6 +37,5 @@ source "board/ep82xxm/Kconfig"
source "board/gw8260/Kconfig"
source "board/iphase4539/Kconfig"
source "board/keymile/km82xx/Kconfig"
-source "board/muas3001/Kconfig"
endmenu
diff --git a/board/muas3001/Kconfig b/board/muas3001/Kconfig
deleted file mode 100644
index 94a00b3..0000000
--- a/board/muas3001/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_MUAS3001
-
-config SYS_BOARD
- default "muas3001"
-
-config SYS_CONFIG_NAME
- default "muas3001"
-
-endif
diff --git a/board/muas3001/MAINTAINERS b/board/muas3001/MAINTAINERS
deleted file mode 100644
index cfb5983..0000000
--- a/board/muas3001/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-MUAS3001 BOARD
-M: Heiko Schocher <hs@denx.de>
-S: Maintained
-F: board/muas3001/
-F: include/configs/muas3001.h
-F: configs/muas3001_defconfig
-F: configs/muas3001_dev_defconfig
diff --git a/board/muas3001/Makefile b/board/muas3001/Makefile
deleted file mode 100644
index ef04960..0000000
--- a/board/muas3001/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2008
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := muas3001.o
diff --git a/board/muas3001/muas3001.c b/board/muas3001/muas3001.c
deleted file mode 100644
index e0c4dba..0000000
--- a/board/muas3001/muas3001.c
+++ /dev/null
@@ -1,335 +0,0 @@
-/*
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8260.h>
-#include <ioports.h>
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#endif
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 0, 0, 0, 0, 0 }, /* PA31 */
- /* PA30 */ { 0, 0, 0, 0, 0, 0 }, /* PA30 */
- /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 TXER */
- /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 TXEN */
- /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 RXDV */
- /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 RXER */
- /* PA25 */ { 1, 0, 0, 1, 0, 0 }, /* ETH_PWRDWN */
- /* PA24 */ { 1, 0, 0, 1, 0, 1 }, /* ETH_RESET */
- /* PA23 */ { 0, 0, 0, 0, 0, 0 }, /* PA23 */
- /* PA22 */ { 0, 0, 0, 0, 0, 0 }, /* PA22 */
- /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD3 */
- /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD2 */
- /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD1 */
- /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD0 */
- /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD0 */
- /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD1 */
- /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD2 */
- /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD3 */
- /* PA13 */ { 0, 0, 0, 0, 0, 0 }, /* PA13 */
- /* PA12 */ { 1, 0, 0, 1, 0, 0 }, /* ETH_SLEEP */
- /* PA11 */ { 0, 0, 0, 0, 0, 0 }, /* PA11 */
- /* PA10 */ { 1, 0, 0, 1, 0, 0 }, /* MDIO */
- /* PA9 */ { 1, 0, 0, 1, 0, 0 }, /* MDC */
- /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RxD */
- /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 0, 0, 0, 0, 0, 0 }, /* PA6 */
- /* PA5 */ { 0, 0, 0, 0, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 0, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 0, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* PA1 */
- /* PA0 */ { 0, 0, 0, 0, 0, 0 } /* PA0 */
- },
-
- /* Port B */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 0, 0, 0, 0, 0, 0 }, /* PB31 */
- /* PB30 */ { 0, 0, 0, 0, 0, 0 }, /* PB30 */
- /* PB29 */ { 0, 0, 0, 0, 0, 0 }, /* PB29 */
- /* PB28 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 TxD */
- /* PB27 */ { 0, 0, 0, 0, 0, 0 }, /* PB27 */
- /* PB26 */ { 0, 0, 0, 0, 0, 0 }, /* PB26 */
- /* PB25 */ { 0, 0, 0, 0, 0, 0 }, /* PB25 */
- /* PB24 */ { 0, 0, 0, 0, 0, 0 }, /* PB24 */
- /* PB23 */ { 0, 0, 0, 0, 0, 0 }, /* PB23 */
- /* PB22 */ { 0, 0, 0, 0, 0, 0 }, /* PB22 */
- /* PB21 */ { 0, 0, 0, 0, 0, 0 }, /* PB21 */
- /* PB20 */ { 0, 0, 0, 0, 0, 0 }, /* PB20 */
- /* PB19 */ { 0, 0, 0, 0, 0, 0 }, /* PB19 */
- /* PB18 */ { 0, 0, 0, 0, 0, 0 }, /* PB18 */
- /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB15 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RxD */
- /* PB14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC3 RxD */
- /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB12 */ { 1, 1, 1, 1, 0, 0 }, /* SCC2 TxD */
- /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB8 */ { 1, 1, 1, 1, 0, 0 }, /* SCC3 TxD */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 1, 1, 1, 1, 0, 0 }, /* Timer1 OUT */
- /* PC29 */ { 0, 0, 0, 0, 0, 0 }, /* PC29 */
- /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* PC23 */
- /* PC22 */ { 0, 0, 0, 0, 0, 0 }, /* PC22 */
- /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC RxCLK 11 */
- /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC TxCLK 12 */
- /* PC19 */ { 0, 0, 0, 0, 0, 0 }, /* PC19 */
- /* PC18 */ { 0, 0, 0, 0, 0, 0 }, /* PC18 */
- /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */
- /* PC15 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TxD */
- /* PC14 */ { 0, 0, 0, 0, 0, 0 }, /* PC14 */
- /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */
- /* PC12 */ { 1, 0, 0, 1, 0, 0 }, /* TX OUTPUT SLEW1 */
- /* PC11 */ { 1, 0, 0, 1, 0, 0 }, /* TX OUTPUT SLEW0 */
- /* PC10 */ { 0, 0, 0, 0, 0, 0 }, /* PC10 */
- /* PC9 */ { 1, 0, 0, 1, 0, 1 }, /* SPA_TX_EN */
- /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 RxD */
- /* PD30 */ { 0, 0, 0, 0, 0, 0 }, /* PD30 */
- /* PD29 */ { 0, 0, 0, 0, 0, 0 }, /* PD29 */
- /* PD28 */ { 0, 0, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* PD27 */
- /* PD26 */ { 0, 0, 0, 0, 0, 0 }, /* PD26 */
- /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4: RXD */
- /* PD21 */ { 1, 1, 0, 1, 0, 0 }, /* SCC4: TXD */
- /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */
- /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */
-#if defined(CONFIG_HARD_I2C)
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
-#else
- /* PD15 */ { 1, 0, 0, 0, 1, 1 }, /* PD15 */
- /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* PD14 */
-#endif
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TxD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RxD */
- /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- }
-};
-
-/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx
- *
- * This routine performs standard 8260 initialization sequence
- * and calculates the available memory size. It may be called
- * several times to try different SDRAM configurations on both
- * 60x and local buses.
- */
-static long int try_init (volatile memctl8260_t * memctl, ulong sdmr,
- ulong orx, volatile uchar * base)
-{
- volatile uchar c = 0xff;
- volatile uint *sdmr_ptr;
- volatile uint *orx_ptr;
- ulong maxsize, size;
- int i;
-
- /* We must be able to test a location outsize the maximum legal size
- * to find out THAT we are outside; but this address still has to be
- * mapped by the controller. That means, that the initial mapping has
- * to be (at least) twice as large as the maximum expected size.
- */
- maxsize = (1 + (~orx | 0x7fff))/* / 2*/;
-
- sdmr_ptr = &memctl->memc_psdmr;
- orx_ptr = &memctl->memc_or1;
-
- *orx_ptr = orx;
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
- */
-
- *sdmr_ptr = sdmr | PSDMR_OP_PREA;
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_MRW;
- *(base + CONFIG_SYS_MRS_OFFS) = c; /* setting MR on address lines */
-
- *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *base = c;
-
- size = get_ram_size ((long *)base, maxsize);
- *orx_ptr = orx | ~(size - 1);
-
- return (size);
-}
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- long psize;
- long sizelittle, sizebig;
-
- memctl->memc_psrt = CONFIG_SYS_PSRT;
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
- /* 60x SDRAM setup:
- */
- sizelittle = try_init (memctl, CONFIG_SYS_PSDMR_LITTLE, CONFIG_SYS_OR1_LITTLE,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- sizebig = try_init (memctl, CONFIG_SYS_PSDMR_BIG, CONFIG_SYS_OR1_BIG,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- if (sizelittle < sizebig) {
- psize = sizebig;
- } else {
- psize = try_init (memctl, CONFIG_SYS_PSDMR_LITTLE, CONFIG_SYS_OR1_LITTLE,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- }
-
- icache_enable ();
-
- return (psize);
-}
-
-int checkboard (void)
-{
- puts ("Board: MUAS3001\n");
-
- return 0;
-}
-
-/*
- * Early board initalization.
- */
-int board_early_init_r (void)
-{
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * update "memory" property in the blob
- */
-void ft_blob_update (void *blob, bd_t *bd)
-{
- int ret, nodeoffset = 0;
- ulong flash_data[4] = {0};
- ulong speed = 0;
-
- /* update Flash addr, size */
- flash_data[2] = cpu_to_be32 (CONFIG_SYS_FLASH_BASE);
- flash_data[3] = cpu_to_be32 (CONFIG_SYS_FLASH_SIZE);
- nodeoffset = fdt_path_offset (blob, "/localbus");
- if (nodeoffset >= 0) {
- ret = fdt_setprop (blob, nodeoffset, "ranges", flash_data,
- sizeof (flash_data));
- if (ret < 0)
- printf ("ft_blob_update): cannot set /localbus/ranges "
- "property err:%s\n", fdt_strerror(ret));
- } else {
- /* memory node is required in dts */
- printf ("ft_blob_update(): cannot find /localbus node "
- "err:%s\n", fdt_strerror (nodeoffset));
- }
-
- /* baudrate */
- nodeoffset = fdt_path_offset (blob, "/soc/cpm/serial");
- if (nodeoffset >= 0) {
- speed = cpu_to_be32 (gd->baudrate);
- ret = fdt_setprop (blob, nodeoffset, "current-speed", &speed,
- sizeof (unsigned long));
- if (ret < 0)
- printf ("ft_blob_update): cannot set /soc/cpm/serial/current-speed "
- "property err:%s\n", fdt_strerror (ret));
- } else {
- /* baudrate is required in dts */
- printf ("ft_blob_update(): cannot find /soc/cpm/smc2/current-speed node "
- "err:%s\n", fdt_strerror (nodeoffset));
- }
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup (blob, bd);
- ft_blob_update (blob, bd);
-
- return 0;
-}
-#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
diff --git a/configs/muas3001_defconfig b/configs/muas3001_defconfig
deleted file mode 100644
index e1056bd..0000000
--- a/configs/muas3001_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_MUAS3001=y
diff --git a/configs/muas3001_dev_defconfig b/configs/muas3001_dev_defconfig
deleted file mode 100644
index a62019c..0000000
--- a/configs/muas3001_dev_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="MUAS_DEV_BOARD"
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_MUAS3001=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index f1c2f8b..7f76aae 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+muas3001 powerpc mpc8260 - - Heiko Schocher <hs@denx.de>
PM825 powerpc mpc8260 - - Wolfgang Denk <wd@denx.de>
PM826 powerpc mpc8260 - - Wolfgang Denk <wd@denx.de>
PM828 powerpc mpc8260 - -
diff --git a/include/configs/muas3001.h b/include/configs/muas3001.h
deleted file mode 100644
index df2ecc1..0000000
--- a/include/configs/muas3001.h
+++ /dev/null
@@ -1,391 +0,0 @@
-/*
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MUAS3001 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-/* Do boardspecific init */
-#define CONFIG_BOARD_EARLY_INIT_R 1
-
-/* enable Watchdog */
-#define CONFIG_WATCHDOG 1
-
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#if defined(CONFIG_MUAS_DEV_BOARD)
-#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
-#else
-#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
-#endif
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
-#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-
-#define CONFIG_ETHER_INDEX 1
-#define CONFIG_ETHER_ON_FCC1
-#define CONFIG_HAS_ETH0
-#define FCC_ENET
-
-/*
- * - Rx-CLK is CLK11
- * - Tx-CLK is CLK12
- */
-# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
-# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
-/*
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- */
-# define CONFIG_SYS_CPMFCR_RAMTYPE (0)
-/* know on local Bus */
-/* define CONFIG_SYS_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */
-/*
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-# define CONFIG_SYS_PHY_ADDR 1
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT 0 /* Port A */
-#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE MDIO_DECLARE
-
-
-#define CONFIG_SYS_MDIO_PIN 0x00200000 /* PA10 */
-#define CONFIG_SYS_MDC_PIN 0x00400000 /* PA9 */
-
-#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
-#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
-#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
- else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
-
-#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
- else iop->pdat &= ~CONFIG_SYS_MDC_PIN
-
-#define MIIDELAY udelay(1)
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-
-/*
- * Default environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "u-boot_addr_r=100000\0" \
- "kernel_addr_r=200000\0" \
- "fdt_addr_r=400000\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "u-boot=muas3001/u-boot.bin\0" \
- "bootfile=muas3001/uImage\0" \
- "fdt_file=muas3001/muas3001.dtb\0" \
- "ramdisk_file=uRamdisk\0" \
- "load=tftp ${u-boot_addr_r} ${u-boot}\0" \
- "update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \
- "cp.b ${u-boot_addr_r} ff000000 ${filesize};" \
- "prot on ff000000 ff03ffff\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:" \
- "${netmask}:${hostname}:${netdev}:off panic=1\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; run nfsargs addip addcons;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "net_self=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "tftp ${ramdisk_addr} ${ramdisk_file}; " \
- "run ramargs addip; " \
- "bootm ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r}\0" \
- "ramdisk_addr=ff210000\0" \
- "kernel_addr=ff050000\0" \
- "fdt_addr=ff200000\0" \
- "flash_self=run ramargs addip addcons;bootm ${kernel_addr}" \
- " ${ramdisk_addr} ${fdt_addr}\0" \
- "updateramdisk=era ${ramdisk_addr} +1f0000;tftpb ${kernel_addr_r}" \
- " ${ramdisk_file};" \
- "cp.b ${kernel_addr_r} ${ramdisk_addr} ${filesize}\0" \
- "updatekernel=era ${kernel_addr} +1b0000;tftpb ${kernel_addr_r}" \
- " ${bootfile};" \
- "cp.b ${kernel_addr_r} ${kernel_addr} ${filesize}\0" \
- "updatefdt=era ${fdt_addr} +10000;tftpb ${fdt_addr_r} ${fdt_file};" \
- "cp.b ${fdt_addr_r} ${fdt_addr} ${filesize}\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_FLASH_SIZE 32
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*
- * I2C Bus
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */
-
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT 0
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SIUMCR 0x00200000
-#define CONFIG_SYS_BCR 0x004c0000
-#define CONFIG_SYS_SCCR 0x0
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 32 bit FLASH
- * 1 60x SDRAM 64 bit SDRAM
- * 4 60x GPCM 16 bit I/O Ctrl
- *
- */
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_32 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (0xff000020)
-
-/* Bank 1 - 60x bus SDRAM
- */
-#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
-
-#define CONFIG_SYS_MPTPR 0x2800
-
-/*-----------------------------------------------------------------------------
- * Address for Mode Register Set (MRS) command
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_MRS_OFFS 0x00000110
-#define CONFIG_SYS_PSRT 0x13
-
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_LITTLE
-
-/* SDRAM initialization values
-*/
-#define CONFIG_SYS_OR1_LITTLE ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI1_A7 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_LITTLE 0x004b36a3
-
-#define CONFIG_SYS_OR1_BIG ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI1_A4 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_BIG 0x014f36a3
-
-/* IO on CS4 initialization values
-*/
-#define CONFIG_SYS_IO_BASE 0xc0000000
-#define CONFIG_SYS_IO_SIZE 1
-
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_IO_BASE & BRx_BA_MSK) |\
- BRx_PS_16 | BRx_MS_GPCM_L | BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (0xfff80020)
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#if defined(CONFIG_MUAS_DEV_BOARD)
-#define OF_STDOUT_PATH "/soc/cpm/serial at 11a90"
-#else
-#define OF_STDOUT_PATH "/soc/cpm/serial at 11a80"
-#endif
-
-#endif /* __CONFIG_H */
--
1.9.1
next prev parent reply other threads:[~2014-12-15 14:26 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-12-15 14:26 [U-Boot] [PATCH 0/26] Start removing non-generic boards Masahiro Yamada
2014-12-15 14:26 ` [U-Boot] [PATCH 01/26] mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 02/26] powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 03/26] mpc8xx: remove ELPT860 board support Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 04/26] mpc8xx: remove KUP4X, KUP4K " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 05/26] mpc8xx: remove SPD823TS " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 06/26] mpc8xx: remove RRvision " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 07/26] mpc8xx: remove R360MPI " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 08/26] mpc8xx: remove NETVIA " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 09/26] mpc8xx: remove lwmon " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 10/26] mpc8xx: remove IVMS8, IVML24 " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 11/26] mpc8xx: remove IP860 " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 12/26] mpc8xx: remove ESTEEM192E " Masahiro Yamada
2015-01-05 18:20 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 13/26] powerpc: remove cogent_8xx, cogent_mpc8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 14/26] mpc8260: remove sacsng " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 15/26] mpc8260: remove ppmc8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 16/26] mpc8260: remove ep8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 17/26] mpc8260: remove VoVPN-GW " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 18/26] mpc8260: remove MPC8266ADS " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 19/26] mpc8260: remove PM825, PM826, PM828 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` Masahiro Yamada [this message]
2015-01-05 18:21 ` [U-Boot] [PATCH 20/26] mpc8260: remove muas3001 " Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 21/26] mpc8260: remove IPHASE4539 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 22/26] mpc8260: remove gw8260 " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 23/26] mpc8260: remove ep82xxm " Masahiro Yamada
2015-01-05 18:21 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 24/26] mpc8260: remove CPU86, CPU87 " Masahiro Yamada
2015-01-05 18:22 ` Tom Rini
2014-12-15 14:26 ` [U-Boot] [PATCH 25/26] mpc8260: remove atc " Masahiro Yamada
2014-12-15 14:26 ` [U-Boot] [PATCH 26/26] powerpc: mpc824x: remove MPC824X cpu support Masahiro Yamada
2014-12-15 16:46 ` York Sun
2015-01-05 18:22 ` Tom Rini
2015-01-05 15:44 ` [U-Boot] [PATCH 0/26] Start removing non-generic boards Masahiro YAMADA
2015-01-05 18:28 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1418653608-14177-21-git-send-email-yamada.m@jp.panasonic.com \
--to=yamada.m@jp.panasonic.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.