[PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Moritz Fischer]

This adds the binding documentation for the Xilinx LogiCORE PR
Decoupler soft core.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
---
 .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
 1 file changed, 24 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt

diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
new file mode 100644
index 0000000..b82b928
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
@@ -0,0 +1,24 @@
+Xilinx LogiCORE Partial Reconfig Decoupler Softcore
+
+The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
+decouplers / fpga bridges.
+The controller can decouple/disable the bridges which prevents signal
+changes from passing through the bridge.  The controller can also
+couple /enable the bridges which allows traffic to pass through the
+bridge normally.
+
+Required properties:
+- compatible		: Should contain "xlnx,pr-decoupler-1.00"
+- regs			: base address and size for decoupler module
+
+Optional properties:
+- bridge-enable		: 0 if driver should disable bridge at startup
+			  1 if driver should enable bridge at startup
+			  Default is to leave bridge in current state.
+
+Example:
+	fpga-bridge@100000450 {
+		compatible = "xlnx,pr-decoupler-1.00";
+		regs = <0x1000 0x10>;
+		bridge-enable = <0>;
+	};
-- 
2.7.4

[PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Moritz Fischer]

This adds the binding documentation for the Xilinx LogiCORE PR
Decoupler soft core.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel at vger.kernel.org
Cc: devicetree at vger.kernel.org
---
 .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
 1 file changed, 24 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt

diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
new file mode 100644
index 0000000..b82b928
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
@@ -0,0 +1,24 @@
+Xilinx LogiCORE Partial Reconfig Decoupler Softcore
+
+The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
+decouplers / fpga bridges.
+The controller can decouple/disable the bridges which prevents signal
+changes from passing through the bridge.  The controller can also
+couple /enable the bridges which allows traffic to pass through the
+bridge normally.
+
+Required properties:
+- compatible		: Should contain "xlnx,pr-decoupler-1.00"
+- regs			: base address and size for decoupler module
+
+Optional properties:
+- bridge-enable		: 0 if driver should disable bridge at startup
+			  1 if driver should enable bridge at startup
+			  Default is to leave bridge in current state.
+
+Example:
+	fpga-bridge at 100000450 {
+		compatible = "xlnx,pr-decoupler-1.00";
+		regs = <0x1000 0x10>;
+		bridge-enable = <0>;
+	};
-- 
2.7.4

[PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Moritz Fischer]

This adds the binding documentation for the Xilinx LogiCORE PR
Decoupler soft core.

Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
---
 .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
 1 file changed, 24 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt

diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
new file mode 100644
index 0000000..b82b928
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
@@ -0,0 +1,24 @@
+Xilinx LogiCORE Partial Reconfig Decoupler Softcore
+
+The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
+decouplers / fpga bridges.
+The controller can decouple/disable the bridges which prevents signal
+changes from passing through the bridge.  The controller can also
+couple /enable the bridges which allows traffic to pass through the
+bridge normally.
+
+Required properties:
+- compatible		: Should contain "xlnx,pr-decoupler-1.00"
+- regs			: base address and size for decoupler module
+
+Optional properties:
+- bridge-enable		: 0 if driver should disable bridge at startup
+			  1 if driver should enable bridge at startup
+			  Default is to leave bridge in current state.
+
+Example:
+	fpga-bridge@100000450 {
+		compatible = "xlnx,pr-decoupler-1.00";
+		regs = <0x1000 0x10>;
+		bridge-enable = <0>;
+	};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

This adds support for the Xilinx LogiCORE PR Decoupler
soft-ip that does decoupling of PR regions in the FPGA
fabric during partial reconfiguration.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
---
 drivers/fpga/Kconfig               |   9 +++
 drivers/fpga/Makefile              |   1 +
 drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
 3 files changed, 166 insertions(+)
 create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index 967cda4..e42c7dc 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -69,6 +69,15 @@ config ALTERA_FREEZE_BRIDGE
 	  isolate one region of the FPGA from the busses while that
 	  region is being reprogrammed.
 
+config XILINX_PR_DECOUPLER
+	tristate "Xilinx LogiCORE PR Decoupler"
+	depends on FPGA_BRIDGE
+	help
+	  Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
+	  The PR Decoupler exists in the FPGA fabric to isolate one
+	  region of the FPGA from the busses while that region is
+	  being reprogrammed during partial reconfig.
+
 endif # FPGA
 
 endmenu
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index cc0d364..3f04bcf 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 obj-$(CONFIG_FPGA_BRIDGE)		+= fpga-bridge.o
 obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)	+= altera-hps2fpga.o altera-fpga2sdram.o
 obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)	+= altera-freeze-bridge.o
+obj-$(CONFIG_XILINX_PR_DECOUPLER)	+= xilinx-pr-decoupler.o
 
 # High Level Interfaces
 obj-$(CONFIG_FPGA_REGION)		+= fpga-region.o
diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
new file mode 100644
index 0000000..07afdd6
--- /dev/null
+++ b/drivers/fpga/xilinx-pr-decoupler.c
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2017, National Instruments Corp.
+ *
+ * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
+ * Decoupler IP Core.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/fpga/fpga-bridge.h>
+
+#define CTRL_OFFSET 0x00
+#define STATUS_OFFSET 0x00
+
+#define CTRL_CMD_MASK		BIT(0)
+#define CTRL_CMD_DECOUPLE	BIT(0)
+#define CTRL_CMD_COUPLE		~BIT(0)
+
+#define STATUS_STATE_MASK	BIT(0)
+#define STATUS_STATE_COUPLED	~BIT(0)
+#define STATUS_STATE_DECOUPLED	BIT(0)
+
+struct xlnx_pr_decoupler_data {
+	void __iomem *io_base;
+	struct clk *clk;
+	bool enable;
+};
+
+static inline void xlnx_pr_decoupler_write(struct xlnx_pr_decoupler_data *p,
+					   u32 offset, u32 val)
+{
+	writel(val, p->io_base + offset);
+}
+
+static inline u32 xlnx_pr_decoupler_read(const struct xlnx_pr_decoupler_data *p,
+					 u32 offset)
+{
+	return readl(p->io_base + offset);
+}
+
+static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable)
+{
+	int err;
+	struct xlnx_pr_decoupler_data *priv = bridge->priv;
+
+	if (priv->enable != enable) {
+		err = clk_enable(priv->clk);
+		if (err)
+			return err;
+
+		xlnx_pr_decoupler_write(priv, CTRL_OFFSET,
+					enable ? CTRL_CMD_COUPLE :
+					CTRL_CMD_DECOUPLE);
+
+		clk_disable(priv->clk);
+	}
+
+	return 0;
+}
+
+static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge)
+{
+	const struct xlnx_pr_decoupler_data *p = bridge->priv;
+
+	return p->enable;
+}
+
+static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
+	.enable_set = xlnx_pr_decoupler_enable_set,
+	.enable_show = xlnx_pr_decoupler_enable_show,
+};
+
+static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
+	{ .compatible = "xlnx,pr-decoupler-1.00", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
+
+static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
+{
+	struct xlnx_pr_decoupler_data *priv;
+	u32 status;
+	int err;
+	struct resource *res;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->io_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->io_base))
+		return PTR_ERR(priv->io_base);
+
+	priv->clk = devm_clk_get(&pdev->dev, "ref_clk");
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev, "input clock not found\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	err = clk_prepare_enable(priv->clk);
+	if (err) {
+		dev_err(&pdev->dev, "unable to enable clock\n");
+		return err;
+	}
+
+	status = xlnx_pr_decoupler_read(priv, STATUS_OFFSET);
+	priv->enable = !!(status & STATUS_STATE_MASK);
+
+	clk_disable(priv->clk);
+
+	err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler",
+				   &xlnx_pr_decoupler_br_ops, priv);
+
+	if (err) {
+		dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
+		clk_unprepare(priv->clk);
+		return err;
+	}
+
+	return 0;
+}
+
+static int xlnx_pr_decoupler_remove(struct platform_device *pdev)
+{
+	fpga_bridge_unregister(&pdev->dev);
+
+	return 0;
+}
+
+static struct platform_driver xlnx_pr_decoupler_driver = {
+	.probe = xlnx_pr_decoupler_probe,
+	.remove = xlnx_pr_decoupler_remove,
+	.driver = {
+		.name = "xlnx_pr_decoupler",
+		.of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match),
+	},
+};
+
+module_platform_driver(xlnx_pr_decoupler_driver);
+
+MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler");
+MODULE_AUTHOR("Moritz Fischer <mdf@kernel.org>");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

This adds support for the Xilinx LogiCORE PR Decoupler
soft-ip that does decoupling of PR regions in the FPGA
fabric during partial reconfiguration.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel at vger.kernel.org
Cc: devicetree at vger.kernel.org
---
 drivers/fpga/Kconfig               |   9 +++
 drivers/fpga/Makefile              |   1 +
 drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
 3 files changed, 166 insertions(+)
 create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index 967cda4..e42c7dc 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -69,6 +69,15 @@ config ALTERA_FREEZE_BRIDGE
 	  isolate one region of the FPGA from the busses while that
 	  region is being reprogrammed.
 
+config XILINX_PR_DECOUPLER
+	tristate "Xilinx LogiCORE PR Decoupler"
+	depends on FPGA_BRIDGE
+	help
+	  Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
+	  The PR Decoupler exists in the FPGA fabric to isolate one
+	  region of the FPGA from the busses while that region is
+	  being reprogrammed during partial reconfig.
+
 endif # FPGA
 
 endmenu
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index cc0d364..3f04bcf 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 obj-$(CONFIG_FPGA_BRIDGE)		+= fpga-bridge.o
 obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)	+= altera-hps2fpga.o altera-fpga2sdram.o
 obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)	+= altera-freeze-bridge.o
+obj-$(CONFIG_XILINX_PR_DECOUPLER)	+= xilinx-pr-decoupler.o
 
 # High Level Interfaces
 obj-$(CONFIG_FPGA_REGION)		+= fpga-region.o
diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
new file mode 100644
index 0000000..07afdd6
--- /dev/null
+++ b/drivers/fpga/xilinx-pr-decoupler.c
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2017, National Instruments Corp.
+ *
+ * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
+ * Decoupler IP Core.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/fpga/fpga-bridge.h>
+
+#define CTRL_OFFSET 0x00
+#define STATUS_OFFSET 0x00
+
+#define CTRL_CMD_MASK		BIT(0)
+#define CTRL_CMD_DECOUPLE	BIT(0)
+#define CTRL_CMD_COUPLE		~BIT(0)
+
+#define STATUS_STATE_MASK	BIT(0)
+#define STATUS_STATE_COUPLED	~BIT(0)
+#define STATUS_STATE_DECOUPLED	BIT(0)
+
+struct xlnx_pr_decoupler_data {
+	void __iomem *io_base;
+	struct clk *clk;
+	bool enable;
+};
+
+static inline void xlnx_pr_decoupler_write(struct xlnx_pr_decoupler_data *p,
+					   u32 offset, u32 val)
+{
+	writel(val, p->io_base + offset);
+}
+
+static inline u32 xlnx_pr_decoupler_read(const struct xlnx_pr_decoupler_data *p,
+					 u32 offset)
+{
+	return readl(p->io_base + offset);
+}
+
+static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable)
+{
+	int err;
+	struct xlnx_pr_decoupler_data *priv = bridge->priv;
+
+	if (priv->enable != enable) {
+		err = clk_enable(priv->clk);
+		if (err)
+			return err;
+
+		xlnx_pr_decoupler_write(priv, CTRL_OFFSET,
+					enable ? CTRL_CMD_COUPLE :
+					CTRL_CMD_DECOUPLE);
+
+		clk_disable(priv->clk);
+	}
+
+	return 0;
+}
+
+static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge)
+{
+	const struct xlnx_pr_decoupler_data *p = bridge->priv;
+
+	return p->enable;
+}
+
+static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
+	.enable_set = xlnx_pr_decoupler_enable_set,
+	.enable_show = xlnx_pr_decoupler_enable_show,
+};
+
+static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
+	{ .compatible = "xlnx,pr-decoupler-1.00", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
+
+static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
+{
+	struct xlnx_pr_decoupler_data *priv;
+	u32 status;
+	int err;
+	struct resource *res;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->io_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->io_base))
+		return PTR_ERR(priv->io_base);
+
+	priv->clk = devm_clk_get(&pdev->dev, "ref_clk");
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev, "input clock not found\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	err = clk_prepare_enable(priv->clk);
+	if (err) {
+		dev_err(&pdev->dev, "unable to enable clock\n");
+		return err;
+	}
+
+	status = xlnx_pr_decoupler_read(priv, STATUS_OFFSET);
+	priv->enable = !!(status & STATUS_STATE_MASK);
+
+	clk_disable(priv->clk);
+
+	err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler",
+				   &xlnx_pr_decoupler_br_ops, priv);
+
+	if (err) {
+		dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
+		clk_unprepare(priv->clk);
+		return err;
+	}
+
+	return 0;
+}
+
+static int xlnx_pr_decoupler_remove(struct platform_device *pdev)
+{
+	fpga_bridge_unregister(&pdev->dev);
+
+	return 0;
+}
+
+static struct platform_driver xlnx_pr_decoupler_driver = {
+	.probe = xlnx_pr_decoupler_probe,
+	.remove = xlnx_pr_decoupler_remove,
+	.driver = {
+		.name = "xlnx_pr_decoupler",
+		.of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match),
+	},
+};
+
+module_platform_driver(xlnx_pr_decoupler_driver);
+
+MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler");
+MODULE_AUTHOR("Moritz Fischer <mdf@kernel.org>");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
> This adds support for the Xilinx LogiCORE PR Decoupler
> soft-ip that does decoupling of PR regions in the FPGA
> fabric during partial reconfiguration.
>
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Cc: Michal Simek <michal.simek@xilinx.com>
> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  drivers/fpga/Kconfig               |   9 +++
>  drivers/fpga/Makefile              |   1 +
>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 166 insertions(+)
>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 967cda4..e42c7dc 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -69,6 +69,15 @@ config ALTERA_FREEZE_BRIDGE
>           isolate one region of the FPGA from the busses while that
>           region is being reprogrammed.
>
> +config XILINX_PR_DECOUPLER
> +       tristate "Xilinx LogiCORE PR Decoupler"
> +       depends on FPGA_BRIDGE
> +       help
> +         Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
> +         The PR Decoupler exists in the FPGA fabric to isolate one
> +         region of the FPGA from the busses while that region is
> +         being reprogrammed during partial reconfig.
> +
>  endif # FPGA
>
>  endmenu
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index cc0d364..3f04bcf 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)      += zynq-fpga.o
>  obj-$(CONFIG_FPGA_BRIDGE)              += fpga-bridge.o
>  obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)      += altera-hps2fpga.o altera-fpga2sdram.o
>  obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)     += altera-freeze-bridge.o
> +obj-$(CONFIG_XILINX_PR_DECOUPLER)      += xilinx-pr-decoupler.o
>
>  # High Level Interfaces
>  obj-$(CONFIG_FPGA_REGION)              += fpga-region.o
> diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
> new file mode 100644
> index 0000000..07afdd6
> --- /dev/null
> +++ b/drivers/fpga/xilinx-pr-decoupler.c
> @@ -0,0 +1,156 @@
> +/*
> + * Copyright (c) 2017, National Instruments Corp.
> + *
> + * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
> + * Decoupler IP Core.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/of_device.h>
> +#include <linux/module.h>
> +#include <linux/fpga/fpga-bridge.h>
> +
> +#define CTRL_OFFSET 0x00
> +#define STATUS_OFFSET 0x00
> +
> +#define CTRL_CMD_MASK          BIT(0)
> +#define CTRL_CMD_DECOUPLE      BIT(0)
> +#define CTRL_CMD_COUPLE                ~BIT(0)
> +
> +#define STATUS_STATE_MASK      BIT(0)
> +#define STATUS_STATE_COUPLED   ~BIT(0)
> +#define STATUS_STATE_DECOUPLED BIT(0)
> +
> +struct xlnx_pr_decoupler_data {
> +       void __iomem *io_base;
> +       struct clk *clk;
> +       bool enable;
> +};
> +
> +static inline void xlnx_pr_decoupler_write(struct xlnx_pr_decoupler_data *p,
> +                                          u32 offset, u32 val)
> +{
> +       writel(val, p->io_base + offset);
> +}
> +
> +static inline u32 xlnx_pr_decoupler_read(const struct xlnx_pr_decoupler_data *p,
> +                                        u32 offset)
> +{
> +       return readl(p->io_base + offset);
> +}
> +
> +static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable)
> +{
> +       int err;
> +       struct xlnx_pr_decoupler_data *priv = bridge->priv;
> +
> +       if (priv->enable != enable) {
> +               err = clk_enable(priv->clk);
> +               if (err)
> +                       return err;
> +
> +               xlnx_pr_decoupler_write(priv, CTRL_OFFSET,
> +                                       enable ? CTRL_CMD_COUPLE :
> +                                       CTRL_CMD_DECOUPLE);
Needs:

+ priv->enable = enable;

This is obviously garbage, priv->enable doesn't get set ...

> +               clk_disable(priv->clk);
> +       }
> +
> +       return 0;
> +}
> +
> +static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge)
> +{
> +       const struct xlnx_pr_decoupler_data *p = bridge->priv;
> +
> +       return p->enable;
> +}
> +
> +static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
> +       .enable_set = xlnx_pr_decoupler_enable_set,
> +       .enable_show = xlnx_pr_decoupler_enable_show,
> +};
> +
> +static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
> +       { .compatible = "xlnx,pr-decoupler-1.00", },
> +       {},
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
> +
> +static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
> +{
> +       struct xlnx_pr_decoupler_data *priv;
> +       u32 status;
> +       int err;
> +       struct resource *res;
> +
> +       priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> +       if (!priv)
> +               return -ENOMEM;
> +
> +       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       priv->io_base = devm_ioremap_resource(&pdev->dev, res);
> +       if (IS_ERR(priv->io_base))
> +               return PTR_ERR(priv->io_base);
> +
> +       priv->clk = devm_clk_get(&pdev->dev, "ref_clk");
> +       if (IS_ERR(priv->clk)) {
> +               dev_err(&pdev->dev, "input clock not found\n");
> +               return PTR_ERR(priv->clk);
> +       }
> +
> +       err = clk_prepare_enable(priv->clk);
> +       if (err) {
> +               dev_err(&pdev->dev, "unable to enable clock\n");
> +               return err;
> +       }
> +
> +       status = xlnx_pr_decoupler_read(priv, STATUS_OFFSET);
> +       priv->enable = !!(status & STATUS_STATE_MASK);
> +
> +       clk_disable(priv->clk);
> +
> +       err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler",
> +                                  &xlnx_pr_decoupler_br_ops, priv);
> +
> +       if (err) {
> +               dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
> +               clk_unprepare(priv->clk);
> +               return err;
> +       }
> +
> +       return 0;
> +}
> +
> +static int xlnx_pr_decoupler_remove(struct platform_device *pdev)
> +{
> +       fpga_bridge_unregister(&pdev->dev);
> +
> +       return 0;
> +}
> +
> +static struct platform_driver xlnx_pr_decoupler_driver = {
> +       .probe = xlnx_pr_decoupler_probe,
> +       .remove = xlnx_pr_decoupler_remove,
> +       .driver = {
> +               .name = "xlnx_pr_decoupler",
> +               .of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match),
> +       },
> +};
> +
> +module_platform_driver(xlnx_pr_decoupler_driver);
> +
> +MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler");
> +MODULE_AUTHOR("Moritz Fischer <mdf@kernel.org>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-fpga" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
> This adds support for the Xilinx LogiCORE PR Decoupler
> soft-ip that does decoupling of PR regions in the FPGA
> fabric during partial reconfiguration.
>
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Cc: Michal Simek <michal.simek@xilinx.com>
> Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel at vger.kernel.org
> Cc: devicetree at vger.kernel.org
> ---
>  drivers/fpga/Kconfig               |   9 +++
>  drivers/fpga/Makefile              |   1 +
>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 166 insertions(+)
>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 967cda4..e42c7dc 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -69,6 +69,15 @@ config ALTERA_FREEZE_BRIDGE
>           isolate one region of the FPGA from the busses while that
>           region is being reprogrammed.
>
> +config XILINX_PR_DECOUPLER
> +       tristate "Xilinx LogiCORE PR Decoupler"
> +       depends on FPGA_BRIDGE
> +       help
> +         Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
> +         The PR Decoupler exists in the FPGA fabric to isolate one
> +         region of the FPGA from the busses while that region is
> +         being reprogrammed during partial reconfig.
> +
>  endif # FPGA
>
>  endmenu
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index cc0d364..3f04bcf 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)      += zynq-fpga.o
>  obj-$(CONFIG_FPGA_BRIDGE)              += fpga-bridge.o
>  obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)      += altera-hps2fpga.o altera-fpga2sdram.o
>  obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)     += altera-freeze-bridge.o
> +obj-$(CONFIG_XILINX_PR_DECOUPLER)      += xilinx-pr-decoupler.o
>
>  # High Level Interfaces
>  obj-$(CONFIG_FPGA_REGION)              += fpga-region.o
> diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
> new file mode 100644
> index 0000000..07afdd6
> --- /dev/null
> +++ b/drivers/fpga/xilinx-pr-decoupler.c
> @@ -0,0 +1,156 @@
> +/*
> + * Copyright (c) 2017, National Instruments Corp.
> + *
> + * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
> + * Decoupler IP Core.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/of_device.h>
> +#include <linux/module.h>
> +#include <linux/fpga/fpga-bridge.h>
> +
> +#define CTRL_OFFSET 0x00
> +#define STATUS_OFFSET 0x00
> +
> +#define CTRL_CMD_MASK          BIT(0)
> +#define CTRL_CMD_DECOUPLE      BIT(0)
> +#define CTRL_CMD_COUPLE                ~BIT(0)
> +
> +#define STATUS_STATE_MASK      BIT(0)
> +#define STATUS_STATE_COUPLED   ~BIT(0)
> +#define STATUS_STATE_DECOUPLED BIT(0)
> +
> +struct xlnx_pr_decoupler_data {
> +       void __iomem *io_base;
> +       struct clk *clk;
> +       bool enable;
> +};
> +
> +static inline void xlnx_pr_decoupler_write(struct xlnx_pr_decoupler_data *p,
> +                                          u32 offset, u32 val)
> +{
> +       writel(val, p->io_base + offset);
> +}
> +
> +static inline u32 xlnx_pr_decoupler_read(const struct xlnx_pr_decoupler_data *p,
> +                                        u32 offset)
> +{
> +       return readl(p->io_base + offset);
> +}
> +
> +static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable)
> +{
> +       int err;
> +       struct xlnx_pr_decoupler_data *priv = bridge->priv;
> +
> +       if (priv->enable != enable) {
> +               err = clk_enable(priv->clk);
> +               if (err)
> +                       return err;
> +
> +               xlnx_pr_decoupler_write(priv, CTRL_OFFSET,
> +                                       enable ? CTRL_CMD_COUPLE :
> +                                       CTRL_CMD_DECOUPLE);
Needs:

+ priv->enable = enable;

This is obviously garbage, priv->enable doesn't get set ...

> +               clk_disable(priv->clk);
> +       }
> +
> +       return 0;
> +}
> +
> +static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge)
> +{
> +       const struct xlnx_pr_decoupler_data *p = bridge->priv;
> +
> +       return p->enable;
> +}
> +
> +static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
> +       .enable_set = xlnx_pr_decoupler_enable_set,
> +       .enable_show = xlnx_pr_decoupler_enable_show,
> +};
> +
> +static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
> +       { .compatible = "xlnx,pr-decoupler-1.00", },
> +       {},
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
> +
> +static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
> +{
> +       struct xlnx_pr_decoupler_data *priv;
> +       u32 status;
> +       int err;
> +       struct resource *res;
> +
> +       priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> +       if (!priv)
> +               return -ENOMEM;
> +
> +       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       priv->io_base = devm_ioremap_resource(&pdev->dev, res);
> +       if (IS_ERR(priv->io_base))
> +               return PTR_ERR(priv->io_base);
> +
> +       priv->clk = devm_clk_get(&pdev->dev, "ref_clk");
> +       if (IS_ERR(priv->clk)) {
> +               dev_err(&pdev->dev, "input clock not found\n");
> +               return PTR_ERR(priv->clk);
> +       }
> +
> +       err = clk_prepare_enable(priv->clk);
> +       if (err) {
> +               dev_err(&pdev->dev, "unable to enable clock\n");
> +               return err;
> +       }
> +
> +       status = xlnx_pr_decoupler_read(priv, STATUS_OFFSET);
> +       priv->enable = !!(status & STATUS_STATE_MASK);
> +
> +       clk_disable(priv->clk);
> +
> +       err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler",
> +                                  &xlnx_pr_decoupler_br_ops, priv);
> +
> +       if (err) {
> +               dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
> +               clk_unprepare(priv->clk);
> +               return err;
> +       }
> +
> +       return 0;
> +}
> +
> +static int xlnx_pr_decoupler_remove(struct platform_device *pdev)
> +{
> +       fpga_bridge_unregister(&pdev->dev);
> +
> +       return 0;
> +}
> +
> +static struct platform_driver xlnx_pr_decoupler_driver = {
> +       .probe = xlnx_pr_decoupler_probe,
> +       .remove = xlnx_pr_decoupler_remove,
> +       .driver = {
> +               .name = "xlnx_pr_decoupler",
> +               .of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match),
> +       },
> +};
> +
> +module_platform_driver(xlnx_pr_decoupler_driver);
> +
> +MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler");
> +MODULE_AUTHOR("Moritz Fischer <mdf@kernel.org>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-fpga" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
> This adds support for the Xilinx LogiCORE PR Decoupler
> soft-ip that does decoupling of PR regions in the FPGA
> fabric during partial reconfiguration.
>
> Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> ---
>  drivers/fpga/Kconfig               |   9 +++
>  drivers/fpga/Makefile              |   1 +
>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 166 insertions(+)
>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 967cda4..e42c7dc 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -69,6 +69,15 @@ config ALTERA_FREEZE_BRIDGE
>           isolate one region of the FPGA from the busses while that
>           region is being reprogrammed.
>
> +config XILINX_PR_DECOUPLER
> +       tristate "Xilinx LogiCORE PR Decoupler"
> +       depends on FPGA_BRIDGE
> +       help
> +         Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
> +         The PR Decoupler exists in the FPGA fabric to isolate one
> +         region of the FPGA from the busses while that region is
> +         being reprogrammed during partial reconfig.
> +
>  endif # FPGA
>
>  endmenu
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index cc0d364..3f04bcf 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)      += zynq-fpga.o
>  obj-$(CONFIG_FPGA_BRIDGE)              += fpga-bridge.o
>  obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)      += altera-hps2fpga.o altera-fpga2sdram.o
>  obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)     += altera-freeze-bridge.o
> +obj-$(CONFIG_XILINX_PR_DECOUPLER)      += xilinx-pr-decoupler.o
>
>  # High Level Interfaces
>  obj-$(CONFIG_FPGA_REGION)              += fpga-region.o
> diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
> new file mode 100644
> index 0000000..07afdd6
> --- /dev/null
> +++ b/drivers/fpga/xilinx-pr-decoupler.c
> @@ -0,0 +1,156 @@
> +/*
> + * Copyright (c) 2017, National Instruments Corp.
> + *
> + * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
> + * Decoupler IP Core.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/of_device.h>
> +#include <linux/module.h>
> +#include <linux/fpga/fpga-bridge.h>
> +
> +#define CTRL_OFFSET 0x00
> +#define STATUS_OFFSET 0x00
> +
> +#define CTRL_CMD_MASK          BIT(0)
> +#define CTRL_CMD_DECOUPLE      BIT(0)
> +#define CTRL_CMD_COUPLE                ~BIT(0)
> +
> +#define STATUS_STATE_MASK      BIT(0)
> +#define STATUS_STATE_COUPLED   ~BIT(0)
> +#define STATUS_STATE_DECOUPLED BIT(0)
> +
> +struct xlnx_pr_decoupler_data {
> +       void __iomem *io_base;
> +       struct clk *clk;
> +       bool enable;
> +};
> +
> +static inline void xlnx_pr_decoupler_write(struct xlnx_pr_decoupler_data *p,
> +                                          u32 offset, u32 val)
> +{
> +       writel(val, p->io_base + offset);
> +}
> +
> +static inline u32 xlnx_pr_decoupler_read(const struct xlnx_pr_decoupler_data *p,
> +                                        u32 offset)
> +{
> +       return readl(p->io_base + offset);
> +}
> +
> +static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable)
> +{
> +       int err;
> +       struct xlnx_pr_decoupler_data *priv = bridge->priv;
> +
> +       if (priv->enable != enable) {
> +               err = clk_enable(priv->clk);
> +               if (err)
> +                       return err;
> +
> +               xlnx_pr_decoupler_write(priv, CTRL_OFFSET,
> +                                       enable ? CTRL_CMD_COUPLE :
> +                                       CTRL_CMD_DECOUPLE);
Needs:

+ priv->enable = enable;

This is obviously garbage, priv->enable doesn't get set ...

> +               clk_disable(priv->clk);
> +       }
> +
> +       return 0;
> +}
> +
> +static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge)
> +{
> +       const struct xlnx_pr_decoupler_data *p = bridge->priv;
> +
> +       return p->enable;
> +}
> +
> +static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
> +       .enable_set = xlnx_pr_decoupler_enable_set,
> +       .enable_show = xlnx_pr_decoupler_enable_show,
> +};
> +
> +static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
> +       { .compatible = "xlnx,pr-decoupler-1.00", },
> +       {},
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
> +
> +static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
> +{
> +       struct xlnx_pr_decoupler_data *priv;
> +       u32 status;
> +       int err;
> +       struct resource *res;
> +
> +       priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> +       if (!priv)
> +               return -ENOMEM;
> +
> +       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       priv->io_base = devm_ioremap_resource(&pdev->dev, res);
> +       if (IS_ERR(priv->io_base))
> +               return PTR_ERR(priv->io_base);
> +
> +       priv->clk = devm_clk_get(&pdev->dev, "ref_clk");
> +       if (IS_ERR(priv->clk)) {
> +               dev_err(&pdev->dev, "input clock not found\n");
> +               return PTR_ERR(priv->clk);
> +       }
> +
> +       err = clk_prepare_enable(priv->clk);
> +       if (err) {
> +               dev_err(&pdev->dev, "unable to enable clock\n");
> +               return err;
> +       }
> +
> +       status = xlnx_pr_decoupler_read(priv, STATUS_OFFSET);
> +       priv->enable = !!(status & STATUS_STATE_MASK);
> +
> +       clk_disable(priv->clk);
> +
> +       err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler",
> +                                  &xlnx_pr_decoupler_br_ops, priv);
> +
> +       if (err) {
> +               dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
> +               clk_unprepare(priv->clk);
> +               return err;
> +       }
> +
> +       return 0;
> +}
> +
> +static int xlnx_pr_decoupler_remove(struct platform_device *pdev)
> +{
> +       fpga_bridge_unregister(&pdev->dev);
> +
> +       return 0;
> +}
> +
> +static struct platform_driver xlnx_pr_decoupler_driver = {
> +       .probe = xlnx_pr_decoupler_probe,
> +       .remove = xlnx_pr_decoupler_remove,
> +       .driver = {
> +               .name = "xlnx_pr_decoupler",
> +               .of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match),
> +       },
> +};
> +
> +module_platform_driver(xlnx_pr_decoupler_driver);
> +
> +MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler");
> +MODULE_AUTHOR("Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-fpga" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

Hi Moritz,

On 10.3.2017 23:42, Moritz Fischer wrote:
> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>> This adds support for the Xilinx LogiCORE PR Decoupler
>> soft-ip that does decoupling of PR regions in the FPGA
>> fabric during partial reconfiguration.
>>
>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>> Cc: Michal Simek <michal.simek@xilinx.com>
>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>> Cc: linux-kernel@vger.kernel.org
>> Cc: devicetree@vger.kernel.org
>> ---
>>  drivers/fpga/Kconfig               |   9 +++
>>  drivers/fpga/Makefile              |   1 +
>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>  3 files changed, 166 insertions(+)
>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

I have written very similar driver some week ago but didn't sent it out.

Here it is.
https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c

Your clk handling is better and my enable_show is better.
You shouldn't rely on setting status before. It is better to read that
reg again. The reason is you can connect status signal from one PR
decoupler to decouple input which can change status

There is another topic I wanted to open in connection to this. There
should be gpio based bridge because this pr decoupler can be without axi
interface and for that gpio driver would be useful.

Thanks,
Michal

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

Hi Moritz,

On 10.3.2017 23:42, Moritz Fischer wrote:
> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>> This adds support for the Xilinx LogiCORE PR Decoupler
>> soft-ip that does decoupling of PR regions in the FPGA
>> fabric during partial reconfiguration.
>>
>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>> Cc: Michal Simek <michal.simek@xilinx.com>
>> Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
>> Cc: linux-kernel at vger.kernel.org
>> Cc: devicetree at vger.kernel.org
>> ---
>>  drivers/fpga/Kconfig               |   9 +++
>>  drivers/fpga/Makefile              |   1 +
>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>  3 files changed, 166 insertions(+)
>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

I have written very similar driver some week ago but didn't sent it out.

Here it is.
https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c

Your clk handling is better and my enable_show is better.
You shouldn't rely on setting status before. It is better to read that
reg again. The reason is you can connect status signal from one PR
decoupler to decouple input which can change status

There is another topic I wanted to open in connection to this. There
should be gpio based bridge because this pr decoupler can be without axi
interface and for that gpio driver would be useful.

Thanks,
Michal

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

Hi Moritz,

On 10.3.2017 23:42, Moritz Fischer wrote:
> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>> This adds support for the Xilinx LogiCORE PR Decoupler
>> soft-ip that does decoupling of PR regions in the FPGA
>> fabric during partial reconfiguration.
>>
>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>> Cc: Michal Simek <michal.simek@xilinx.com>
>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>> Cc: linux-kernel@vger.kernel.org
>> Cc: devicetree@vger.kernel.org
>> ---
>>  drivers/fpga/Kconfig               |   9 +++
>>  drivers/fpga/Makefile              |   1 +
>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>  3 files changed, 166 insertions(+)
>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

I have written very similar driver some week ago but didn't sent it out.

Here it is.
https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c

Your clk handling is better and my enable_show is better.
You shouldn't rely on setting status before. It is better to read that
reg again. The reason is you can connect status signal from one PR
decoupler to decouple input which can change status

There is another topic I wanted to open in connection to this. There
should be gpio based bridge because this pr decoupler can be without axi
interface and for that gpio driver would be useful.

Thanks,
Michal

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

Hi Moritz,

On 10.3.2017 23:42, Moritz Fischer wrote:
> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
>> This adds support for the Xilinx LogiCORE PR Decoupler
>> soft-ip that does decoupling of PR regions in the FPGA
>> fabric during partial reconfiguration.
>>
>> Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>> Cc: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>> Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>> Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> ---
>>  drivers/fpga/Kconfig               |   9 +++
>>  drivers/fpga/Makefile              |   1 +
>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>  3 files changed, 166 insertions(+)
>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

I have written very similar driver some week ago but didn't sent it out.

Here it is.
https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c

Your clk handling is better and my enable_show is better.
You shouldn't rely on setting status before. It is better to read that
reg again. The reason is you can connect status signal from one PR
decoupler to decouple input which can change status

There is another topic I wanted to open in connection to this. There
should be gpio based bridge because this pr decoupler can be without axi
interface and for that gpio driver would be useful.

Thanks,
Michal


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek@xilinx.com> wrote:
> Hi Moritz,
>
> On 10.3.2017 23:42, Moritz Fischer wrote:
>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>> soft-ip that does decoupling of PR regions in the FPGA
>>> fabric during partial reconfiguration.
>>>
>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>> Cc: linux-kernel@vger.kernel.org
>>> Cc: devicetree@vger.kernel.org
>>> ---
>>>  drivers/fpga/Kconfig               |   9 +++
>>>  drivers/fpga/Makefile              |   1 +
>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>  3 files changed, 166 insertions(+)
>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> I have written very similar driver some week ago but didn't sent it out.

Hah. I'll take a look.

> Here it is.
> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>
> Your clk handling is better and my enable_show is better.
> You shouldn't rely on setting status before. It is better to read that
> reg again. The reason is you can connect status signal from one PR
> decoupler to decouple input which can change status

I will just merge them together and add you to author's list if that's
fine with you?

> There is another topic I wanted to open in connection to this. There
> should be gpio based bridge because this pr decoupler can be without axi
> interface and for that gpio driver would be useful.

That's a good idea. I can look at that. This can be pretty generic
code I suppose.

Cheers,

Moritz

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek@xilinx.com> wrote:
> Hi Moritz,
>
> On 10.3.2017 23:42, Moritz Fischer wrote:
>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>> soft-ip that does decoupling of PR regions in the FPGA
>>> fabric during partial reconfiguration.
>>>
>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>> Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
>>> Cc: linux-kernel at vger.kernel.org
>>> Cc: devicetree at vger.kernel.org
>>> ---
>>>  drivers/fpga/Kconfig               |   9 +++
>>>  drivers/fpga/Makefile              |   1 +
>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>  3 files changed, 166 insertions(+)
>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> I have written very similar driver some week ago but didn't sent it out.

Hah. I'll take a look.

> Here it is.
> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>
> Your clk handling is better and my enable_show is better.
> You shouldn't rely on setting status before. It is better to read that
> reg again. The reason is you can connect status signal from one PR
> decoupler to decouple input which can change status

I will just merge them together and add you to author's list if that's
fine with you?

> There is another topic I wanted to open in connection to this. There
> should be gpio based bridge because this pr decoupler can be without axi
> interface and for that gpio driver would be useful.

That's a good idea. I can look at that. This can be pretty generic
code I suppose.

Cheers,

Moritz

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Moritz Fischer]

On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org> wrote:
> Hi Moritz,
>
> On 10.3.2017 23:42, Moritz Fischer wrote:
>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>> soft-ip that does decoupling of PR regions in the FPGA
>>> fabric during partial reconfiguration.
>>>
>>> Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>>> Cc: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>>> Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>>> Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>>> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>>> ---
>>>  drivers/fpga/Kconfig               |   9 +++
>>>  drivers/fpga/Makefile              |   1 +
>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>  3 files changed, 166 insertions(+)
>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> I have written very similar driver some week ago but didn't sent it out.

Hah. I'll take a look.

> Here it is.
> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>
> Your clk handling is better and my enable_show is better.
> You shouldn't rely on setting status before. It is better to read that
> reg again. The reason is you can connect status signal from one PR
> decoupler to decouple input which can change status

I will just merge them together and add you to author's list if that's
fine with you?

> There is another topic I wanted to open in connection to this. There
> should be gpio based bridge because this pr decoupler can be without axi
> interface and for that gpio driver would be useful.

That's a good idea. I can look at that. This can be pretty generic
code I suppose.

Cheers,

Moritz
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

On 13.3.2017 17:18, Moritz Fischer wrote:
> On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek@xilinx.com> wrote:
>> Hi Moritz,
>>
>> On 10.3.2017 23:42, Moritz Fischer wrote:
>>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>>> soft-ip that does decoupling of PR regions in the FPGA
>>>> fabric during partial reconfiguration.
>>>>
>>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>>> Cc: linux-kernel@vger.kernel.org
>>>> Cc: devicetree@vger.kernel.org
>>>> ---
>>>>  drivers/fpga/Kconfig               |   9 +++
>>>>  drivers/fpga/Makefile              |   1 +
>>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>>  3 files changed, 166 insertions(+)
>>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>>
>> I have written very similar driver some week ago but didn't sent it out.
> 
> Hah. I'll take a look.
> 
>> Here it is.
>> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>>
>> Your clk handling is better and my enable_show is better.
>> You shouldn't rely on setting status before. It is better to read that
>> reg again. The reason is you can connect status signal from one PR
>> decoupler to decouple input which can change status
> 
> I will just merge them together and add you to author's list if that's
> fine with you?

sure. Go ahead.

> 
>> There is another topic I wanted to open in connection to this. There
>> should be gpio based bridge because this pr decoupler can be without axi
>> interface and for that gpio driver would be useful.
> 
> That's a good idea. I can look at that. This can be pretty generic
> code I suppose.

yes - it should be. Simple gpio driver with polarity support should be
enough.

Thanks,
Michal

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

On 13.3.2017 17:18, Moritz Fischer wrote:
> On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek@xilinx.com> wrote:
>> Hi Moritz,
>>
>> On 10.3.2017 23:42, Moritz Fischer wrote:
>>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>>> soft-ip that does decoupling of PR regions in the FPGA
>>>> fabric during partial reconfiguration.
>>>>
>>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>>> Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
>>>> Cc: linux-kernel at vger.kernel.org
>>>> Cc: devicetree at vger.kernel.org
>>>> ---
>>>>  drivers/fpga/Kconfig               |   9 +++
>>>>  drivers/fpga/Makefile              |   1 +
>>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>>  3 files changed, 166 insertions(+)
>>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>>
>> I have written very similar driver some week ago but didn't sent it out.
> 
> Hah. I'll take a look.
> 
>> Here it is.
>> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>>
>> Your clk handling is better and my enable_show is better.
>> You shouldn't rely on setting status before. It is better to read that
>> reg again. The reason is you can connect status signal from one PR
>> decoupler to decouple input which can change status
> 
> I will just merge them together and add you to author's list if that's
> fine with you?

sure. Go ahead.

> 
>> There is another topic I wanted to open in connection to this. There
>> should be gpio based bridge because this pr decoupler can be without axi
>> interface and for that gpio driver would be useful.
> 
> That's a good idea. I can look at that. This can be pretty generic
> code I suppose.

yes - it should be. Simple gpio driver with polarity support should be
enough.

Thanks,
Michal

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

On 13.3.2017 17:18, Moritz Fischer wrote:
> On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek@xilinx.com> wrote:
>> Hi Moritz,
>>
>> On 10.3.2017 23:42, Moritz Fischer wrote:
>>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>>> soft-ip that does decoupling of PR regions in the FPGA
>>>> fabric during partial reconfiguration.
>>>>
>>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>>> Cc: linux-kernel@vger.kernel.org
>>>> Cc: devicetree@vger.kernel.org
>>>> ---
>>>>  drivers/fpga/Kconfig               |   9 +++
>>>>  drivers/fpga/Makefile              |   1 +
>>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>>  3 files changed, 166 insertions(+)
>>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>>
>> I have written very similar driver some week ago but didn't sent it out.
> 
> Hah. I'll take a look.
> 
>> Here it is.
>> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>>
>> Your clk handling is better and my enable_show is better.
>> You shouldn't rely on setting status before. It is better to read that
>> reg again. The reason is you can connect status signal from one PR
>> decoupler to decouple input which can change status
> 
> I will just merge them together and add you to author's list if that's
> fine with you?

sure. Go ahead.

> 
>> There is another topic I wanted to open in connection to this. There
>> should be gpio based bridge because this pr decoupler can be without axi
>> interface and for that gpio driver would be useful.
> 
> That's a good idea. I can look at that. This can be pretty generic
> code I suppose.

yes - it should be. Simple gpio driver with polarity support should be
enough.

Thanks,
Michal

Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

[Michal Simek]

On 13.3.2017 17:18, Moritz Fischer wrote:
> On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org> wrote:
>> Hi Moritz,
>>
>> On 10.3.2017 23:42, Moritz Fischer wrote:
>>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
>>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>>> soft-ip that does decoupling of PR regions in the FPGA
>>>> fabric during partial reconfiguration.
>>>>
>>>> Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>>>> Cc: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>>>> Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>>>> Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>>>> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>>>> ---
>>>>  drivers/fpga/Kconfig               |   9 +++
>>>>  drivers/fpga/Makefile              |   1 +
>>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>>  3 files changed, 166 insertions(+)
>>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>>
>> I have written very similar driver some week ago but didn't sent it out.
> 
> Hah. I'll take a look.
> 
>> Here it is.
>> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>>
>> Your clk handling is better and my enable_show is better.
>> You shouldn't rely on setting status before. It is better to read that
>> reg again. The reason is you can connect status signal from one PR
>> decoupler to decouple input which can change status
> 
> I will just merge them together and add you to author's list if that's
> fine with you?

sure. Go ahead.

> 
>> There is another topic I wanted to open in connection to this. There
>> should be gpio based bridge because this pr decoupler can be without axi
>> interface and for that gpio driver would be useful.
> 
> That's a good idea. I can look at that. This can be pretty generic
> code I suppose.

yes - it should be. Simple gpio driver with polarity support should be
enough.

Thanks,
Michal



--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Michal Simek]

On 10.3.2017 22:30, Moritz Fischer wrote:
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Cc: Michal Simek <michal.simek@xilinx.com>
> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 0000000..b82b928
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,24 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple /enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00"
> +- regs			: base address and size for decoupler module
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +Example:
> +	fpga-bridge@100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00";
> +		regs = <0x1000 0x10>;
> +		bridge-enable = <0>;
> +	};
> 

Look at.
https://github.com/Xilinx/linux-xlnx/blob/master/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt


And you miss above required clk property. I do use aclk because this is
what it is shown in vivado.

Thanks,
Michal

[PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Michal Simek]

On 10.3.2017 22:30, Moritz Fischer wrote:
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Cc: Michal Simek <michal.simek@xilinx.com>
> Cc: S?ren Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel at vger.kernel.org
> Cc: devicetree at vger.kernel.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 0000000..b82b928
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,24 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple /enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00"
> +- regs			: base address and size for decoupler module
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +Example:
> +	fpga-bridge at 100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00";
> +		regs = <0x1000 0x10>;
> +		bridge-enable = <0>;
> +	};
> 

Look at.
https://github.com/Xilinx/linux-xlnx/blob/master/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt


And you miss above required clk property. I do use aclk because this is
what it is shown in vivado.

Thanks,
Michal

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Michal Simek]

On 10.3.2017 22:30, Moritz Fischer wrote:
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Cc: Michal Simek <michal.simek@xilinx.com>
> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 0000000..b82b928
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,24 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple /enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00"
> +- regs			: base address and size for decoupler module
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +Example:
> +	fpga-bridge@100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00";
> +		regs = <0x1000 0x10>;
> +		bridge-enable = <0>;
> +	};
> 

Look at.
https://github.com/Xilinx/linux-xlnx/blob/master/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt


And you miss above required clk property. I do use aclk because this is
what it is shown in vivado.

Thanks,
Michal

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Michal Simek]

On 10.3.2017 22:30, Moritz Fischer wrote:
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 24 ++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 0000000..b82b928
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,24 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler  manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple /enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00"
> +- regs			: base address and size for decoupler module
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +Example:
> +	fpga-bridge@100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00";
> +		regs = <0x1000 0x10>;
> +		bridge-enable = <0>;
> +	};
> 

Look at.
https://github.com/Xilinx/linux-xlnx/blob/master/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt


And you miss above required clk property. I do use aclk because this is
what it is shown in vivado.

Thanks,
Michal

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 0/2] fpga: Xilinx LogiCore PR Decoupler

[Alan Tull]

Hi Greg,

Please take these two patches for Xilinx LogiCore
PR Decouper for the FPGA bridge framework.

Thanks,
Alan


Moritz Fischer (2):
  doc: Add bindings document for Xilinx LogiCore PR Decoupler
  fpga: Add support for Xilinx LogiCORE PR Decoupler

 .../bindings/fpga/xilinx-pr-decoupler.txt          |  35 +++++
 drivers/fpga/Kconfig                               |  10 ++
 drivers/fpga/Makefile                              |   1 +
 drivers/fpga/xilinx-pr-decoupler.c                 | 161 +++++++++++++++++++++
 4 files changed, 207 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
 create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

-- 
2.11.0

[PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Alan Tull]

From: Moritz Fischer <mdf@kernel.org>

This adds the binding documentation for the Xilinx LogiCORE PR
Decoupler soft core.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Alan Tull <atull@kernel.org>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
---
 .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt

diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
new file mode 100644
index 000000000000..2c527ac30398
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
@@ -0,0 +1,35 @@
+Xilinx LogiCORE Partial Reconfig Decoupler Softcore
+
+The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
+decouplers / fpga bridges.
+The controller can decouple/disable the bridges which prevents signal
+changes from passing through the bridge.  The controller can also
+couple / enable the bridges which allows traffic to pass through the
+bridge normally.
+
+The Driver supports only MMIO handling. A PR region can have multiple
+PR Decouplers which can be handled independently or chained via decouple/
+decouple_status signals.
+
+Required properties:
+- compatible		: Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
+- regs			: base address and size for decoupler module
+- clocks		: input clock to IP
+- clock-names		: should contain "aclk"
+
+Optional properties:
+- bridge-enable		: 0 if driver should disable bridge at startup
+			  1 if driver should enable bridge at startup
+			  Default is to leave bridge in current state.
+
+See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
+
+Example:
+	fpga-bridge@100000450 {
+		compatible = "xlnx,pr-decoupler-1.00",
+			     "xlnx-pr-decoupler";
+		regs = <0x10000045 0x10>;
+		clocks = <&clkc 15>;
+		clock-names = "aclk";
+		bridge-enable = <0>;
+	};
-- 
2.11.0

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Rob Herring]

On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
> From: Moritz Fischer <mdf@kernel.org>

Please use "dt-bindings: fpga: ..." for the subject.


> 
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> Acked-by: Alan Tull <atull@kernel.org>

I'm confused why you are sending these instead of Moritz? If it goes 
through you, then it should have your S-o-B too.

> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 000000000000..2c527ac30398
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,35 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple / enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +The Driver supports only MMIO handling. A PR region can have multiple
> +PR Decouplers which can be handled independently or chained via decouple/
> +decouple_status signals.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"

I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather 
"followed by". Plus the example has both.

> +- regs			: base address and size for decoupler module
> +- clocks		: input clock to IP
> +- clock-names		: should contain "aclk"
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
> +
> +Example:
> +	fpga-bridge@100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00",
> +			     "xlnx-pr-decoupler";
> +		regs = <0x10000045 0x10>;
> +		clocks = <&clkc 15>;
> +		clock-names = "aclk";
> +		bridge-enable = <0>;
> +	};
> -- 
> 2.11.0
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Rob Herring]

On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
> From: Moritz Fischer <mdf@kernel.org>

Please use "dt-bindings: fpga: ..." for the subject.


> 
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> Acked-by: Alan Tull <atull@kernel.org>

I'm confused why you are sending these instead of Moritz? If it goes 
through you, then it should have your S-o-B too.

> Cc: S�ren Brinkmann <soren.brinkmann@xilinx.com>
> Cc: linux-kernel@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 000000000000..2c527ac30398
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,35 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple / enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +The Driver supports only MMIO handling. A PR region can have multiple
> +PR Decouplers which can be handled independently or chained via decouple/
> +decouple_status signals.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"

I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather 
"followed by". Plus the example has both.

> +- regs			: base address and size for decoupler module
> +- clocks		: input clock to IP
> +- clock-names		: should contain "aclk"
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
> +
> +Example:
> +	fpga-bridge@100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00",
> +			     "xlnx-pr-decoupler";
> +		regs = <0x10000045 0x10>;
> +		clocks = <&clkc 15>;
> +		clock-names = "aclk";
> +		bridge-enable = <0>;
> +	};
> -- 
> 2.11.0
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Rob Herring]

On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
> From: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

Please use "dt-bindings: fpga: ..." for the subject.


> 
> This adds the binding documentation for the Xilinx LogiCORE PR
> Decoupler soft core.
> 
> Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Signed-off-by: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> Acked-by: Alan Tull <atull-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

I'm confused why you are sending these instead of Moritz? If it goes 
through you, then it should have your S-o-B too.

> Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> ---
>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> new file mode 100644
> index 000000000000..2c527ac30398
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -0,0 +1,35 @@
> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> +
> +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
> +decouplers / fpga bridges.
> +The controller can decouple/disable the bridges which prevents signal
> +changes from passing through the bridge.  The controller can also
> +couple / enable the bridges which allows traffic to pass through the
> +bridge normally.
> +
> +The Driver supports only MMIO handling. A PR region can have multiple
> +PR Decouplers which can be handled independently or chained via decouple/
> +decouple_status signals.
> +
> +Required properties:
> +- compatible		: Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"

I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather 
"followed by". Plus the example has both.

> +- regs			: base address and size for decoupler module
> +- clocks		: input clock to IP
> +- clock-names		: should contain "aclk"
> +
> +Optional properties:
> +- bridge-enable		: 0 if driver should disable bridge at startup
> +			  1 if driver should enable bridge at startup
> +			  Default is to leave bridge in current state.
> +
> +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
> +
> +Example:
> +	fpga-bridge@100000450 {
> +		compatible = "xlnx,pr-decoupler-1.00",
> +			     "xlnx-pr-decoupler";
> +		regs = <0x10000045 0x10>;
> +		clocks = <&clkc 15>;
> +		clock-names = "aclk";
> +		bridge-enable = <0>;
> +	};
> -- 
> 2.11.0
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Moritz Fischer]

On Thu, Mar 30, 2017 at 05:44:29PM -0500, Rob Herring wrote:
> On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
> > From: Moritz Fischer <mdf@kernel.org>
>
> Please use "dt-bindings: fpga: ..." for the subject.
>
>
> >
> > This adds the binding documentation for the Xilinx LogiCORE PR
> > Decoupler soft core.
> >
> > Signed-off-by: Moritz Fischer <mdf@kernel.org>
> > Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> > Acked-by: Alan Tull <atull@kernel.org>
>
> I'm confused why you are sending these instead of Moritz? If it goes
> through you, then it should have your S-o-B too.

Do you want me to resend this Alan (with Rob's suggestions)?
>
> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
> > Cc: linux-kernel@vger.kernel.org
> > Cc: devicetree@vger.kernel.org
> > ---
> >  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
> >  1 file changed, 35 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> >
> > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> > new file mode 100644
> > index 000000000000..2c527ac30398
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> > @@ -0,0 +1,35 @@
> > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> > +
> > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
> > +decouplers / fpga bridges.
> > +The controller can decouple/disable the bridges which prevents signal
> > +changes from passing through the bridge.  The controller can also
> > +couple / enable the bridges which allows traffic to pass through the
> > +bridge normally.
> > +
> > +The Driver supports only MMIO handling. A PR region can have multiple
> > +PR Decouplers which can be handled independently or chained via decouple/
> > +decouple_status signals.
> > +
> > +Required properties:
> > +- compatible : Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
>
> I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather
> "followed by". Plus the example has both.

Michal wanted to have both, so I put both. Personally I don't care. I
think they have some downstream stuff that relied on it.

>
> > +- regs : base address and size for decoupler module
> > +- clocks : input clock to IP
> > +- clock-names : should contain "aclk"
> > +
> > +Optional properties:
> > +- bridge-enable : 0 if driver should disable bridge at startup
> > +  1 if driver should enable bridge at startup
> > +  Default is to leave bridge in current state.
> > +
> > +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
> > +
> > +Example:
> > + fpga-bridge@100000450 {
> > + compatible = "xlnx,pr-decoupler-1.00",
> > +     "xlnx-pr-decoupler";
> > + regs = <0x10000045 0x10>;
> > + clocks = <&clkc 15>;
> > + clock-names = "aclk";
> > + bridge-enable = <0>;
> > + };
> > --
> > 2.11.0
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html

Thanks,
Moritz

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Moritz Fischer]

On Thu, Mar 30, 2017 at 05:44:29PM -0500, Rob Herring wrote:
> On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
> > From: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>
> Please use "dt-bindings: fpga: ..." for the subject.
>
>
> >
> > This adds the binding documentation for the Xilinx LogiCORE PR
> > Decoupler soft core.
> >
> > Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> > Signed-off-by: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> > Acked-by: Alan Tull <atull-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>
> I'm confused why you are sending these instead of Moritz? If it goes
> through you, then it should have your S-o-B too.

Do you want me to resend this Alan (with Rob's suggestions)?
>
> > Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> > Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> > Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> > ---
> >  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
> >  1 file changed, 35 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> >
> > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> > new file mode 100644
> > index 000000000000..2c527ac30398
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> > @@ -0,0 +1,35 @@
> > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
> > +
> > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
> > +decouplers / fpga bridges.
> > +The controller can decouple/disable the bridges which prevents signal
> > +changes from passing through the bridge.  The controller can also
> > +couple / enable the bridges which allows traffic to pass through the
> > +bridge normally.
> > +
> > +The Driver supports only MMIO handling. A PR region can have multiple
> > +PR Decouplers which can be handled independently or chained via decouple/
> > +decouple_status signals.
> > +
> > +Required properties:
> > +- compatible : Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
>
> I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather
> "followed by". Plus the example has both.

Michal wanted to have both, so I put both. Personally I don't care. I
think they have some downstream stuff that relied on it.

>
> > +- regs : base address and size for decoupler module
> > +- clocks : input clock to IP
> > +- clock-names : should contain "aclk"
> > +
> > +Optional properties:
> > +- bridge-enable : 0 if driver should disable bridge at startup
> > +  1 if driver should enable bridge at startup
> > +  Default is to leave bridge in current state.
> > +
> > +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
> > +
> > +Example:
> > + fpga-bridge@100000450 {
> > + compatible = "xlnx,pr-decoupler-1.00",
> > +     "xlnx-pr-decoupler";
> > + regs = <0x10000045 0x10>;
> > + clocks = <&clkc 15>;
> > + clock-names = "aclk";
> > + bridge-enable = <0>;
> > + };
> > --
> > 2.11.0
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
> > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html

Thanks,
Moritz
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Michal Simek]

On 5.4.2017 01:36, Moritz Fischer wrote:
> On Thu, Mar 30, 2017 at 05:44:29PM -0500, Rob Herring wrote:
>> On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
>>> From: Moritz Fischer <mdf@kernel.org>
>>
>> Please use "dt-bindings: fpga: ..." for the subject.
>>
>>
>>>
>>> This adds the binding documentation for the Xilinx LogiCORE PR
>>> Decoupler soft core.
>>>
>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>>> Acked-by: Alan Tull <atull@kernel.org>
>>
>> I'm confused why you are sending these instead of Moritz? If it goes
>> through you, then it should have your S-o-B too.
> 
> Do you want me to resend this Alan (with Rob's suggestions)?
>>
>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>> Cc: linux-kernel@vger.kernel.org
>>> Cc: devicetree@vger.kernel.org
>>> ---
>>>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>>>  1 file changed, 35 insertions(+)
>>>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>>> new file mode 100644
>>> index 000000000000..2c527ac30398
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>>> @@ -0,0 +1,35 @@
>>> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
>>> +
>>> +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
>>> +decouplers / fpga bridges.
>>> +The controller can decouple/disable the bridges which prevents signal
>>> +changes from passing through the bridge.  The controller can also
>>> +couple / enable the bridges which allows traffic to pass through the
>>> +bridge normally.
>>> +
>>> +The Driver supports only MMIO handling. A PR region can have multiple
>>> +PR Decouplers which can be handled independently or chained via decouple/
>>> +decouple_status signals.
>>> +
>>> +Required properties:
>>> +- compatible : Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
>>
>> I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather
>> "followed by". Plus the example has both.
> 
> Michal wanted to have both, so I put both. Personally I don't care. I
> think they have some downstream stuff that relied on it.

Agree with Rob with using "followed by" instead of or.

M

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Michal Simek]

On 5.4.2017 01:36, Moritz Fischer wrote:
> On Thu, Mar 30, 2017 at 05:44:29PM -0500, Rob Herring wrote:
>> On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
>>> From: Moritz Fischer <mdf@kernel.org>
>>
>> Please use "dt-bindings: fpga: ..." for the subject.
>>
>>
>>>
>>> This adds the binding documentation for the Xilinx LogiCORE PR
>>> Decoupler soft core.
>>>
>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>>> Acked-by: Alan Tull <atull@kernel.org>
>>
>> I'm confused why you are sending these instead of Moritz? If it goes
>> through you, then it should have your S-o-B too.
> 
> Do you want me to resend this Alan (with Rob's suggestions)?
>>
>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>> Cc: linux-kernel@vger.kernel.org
>>> Cc: devicetree@vger.kernel.org
>>> ---
>>>  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>>>  1 file changed, 35 insertions(+)
>>>  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>>> new file mode 100644
>>> index 000000000000..2c527ac30398
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>>> @@ -0,0 +1,35 @@
>>> +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
>>> +
>>> +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
>>> +decouplers / fpga bridges.
>>> +The controller can decouple/disable the bridges which prevents signal
>>> +changes from passing through the bridge.  The controller can also
>>> +couple / enable the bridges which allows traffic to pass through the
>>> +bridge normally.
>>> +
>>> +The Driver supports only MMIO handling. A PR region can have multiple
>>> +PR Decouplers which can be handled independently or chained via decouple/
>>> +decouple_status signals.
>>> +
>>> +Required properties:
>>> +- compatible : Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
>>
>> I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather
>> "followed by". Plus the example has both.
> 
> Michal wanted to have both, so I put both. Personally I don't care. I
> think they have some downstream stuff that relied on it.

Agree with Rob with using "followed by" instead of or.

M

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Alan Tull]

On Tue, Apr 4, 2017 at 6:36 PM, Moritz Fischer <moritz.fischer@ettus.com> wrote:
> On Thu, Mar 30, 2017 at 05:44:29PM -0500, Rob Herring wrote:
>> On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
>> > From: Moritz Fischer <mdf@kernel.org>
>>
>> Please use "dt-bindings: fpga: ..." for the subject.
>>
>>
>> >
>> > This adds the binding documentation for the Xilinx LogiCORE PR
>> > Decoupler soft core.
>> >
>> > Signed-off-by: Moritz Fischer <mdf@kernel.org>
>> > Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>> > Acked-by: Alan Tull <atull@kernel.org>
>>
>> I'm confused why you are sending these instead of Moritz? If it goes
>> through you, then it should have your S-o-B too.

Greg asked me to send patches to him.  I should have started adding my
signed-of-by
at that point.

>
> Do you want me to resend this Alan (with Rob's suggestions)?

I sent a set of patches to Greg on March 24.  Looking back on that I realize
that it didn't have Rob's ack yet (as well as having my ack where it should
have been my signed-of-by).

Yes, please resend this patchset with Rob's feedback.

Thanks,
ALan

>>
>> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>> > Cc: linux-kernel@vger.kernel.org
>> > Cc: devicetree@vger.kernel.org
>> > ---
>> >  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>> >  1 file changed, 35 insertions(+)
>> >  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>> > new file mode 100644
>> > index 000000000000..2c527ac30398
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>> > @@ -0,0 +1,35 @@
>> > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
>> > +
>> > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
>> > +decouplers / fpga bridges.
>> > +The controller can decouple/disable the bridges which prevents signal
>> > +changes from passing through the bridge.  The controller can also
>> > +couple / enable the bridges which allows traffic to pass through the
>> > +bridge normally.
>> > +
>> > +The Driver supports only MMIO handling. A PR region can have multiple
>> > +PR Decouplers which can be handled independently or chained via decouple/
>> > +decouple_status signals.
>> > +
>> > +Required properties:
>> > +- compatible : Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
>>
>> I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather
>> "followed by". Plus the example has both.
>
> Michal wanted to have both, so I put both. Personally I don't care. I
> think they have some downstream stuff that relied on it.
>
>>
>> > +- regs : base address and size for decoupler module
>> > +- clocks : input clock to IP
>> > +- clock-names : should contain "aclk"
>> > +
>> > +Optional properties:
>> > +- bridge-enable : 0 if driver should disable bridge at startup
>> > +  1 if driver should enable bridge at startup
>> > +  Default is to leave bridge in current state.
>> > +
>> > +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
>> > +
>> > +Example:
>> > + fpga-bridge@100000450 {
>> > + compatible = "xlnx,pr-decoupler-1.00",
>> > +     "xlnx-pr-decoupler";
>> > + regs = <0x10000045 0x10>;
>> > + clocks = <&clkc 15>;
>> > + clock-names = "aclk";
>> > + bridge-enable = <0>;
>> > + };
>> > --
>> > 2.11.0
>> >
>> > --
>> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> > the body of a message to majordomo@vger.kernel.org
>> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
> Thanks,
> Moritz

Re: [PATCH 1/2] doc: Add bindings document for Xilinx LogiCore PR Decoupler

[Alan Tull]

On Tue, Apr 4, 2017 at 6:36 PM, Moritz Fischer <moritz.fischer-+aYTwkv1SeIAvxtiuMwx3w@public.gmane.org> wrote:
> On Thu, Mar 30, 2017 at 05:44:29PM -0500, Rob Herring wrote:
>> On Fri, Mar 24, 2017 at 10:33:20AM -0500, Alan Tull wrote:
>> > From: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>>
>> Please use "dt-bindings: fpga: ..." for the subject.
>>
>>
>> >
>> > This adds the binding documentation for the Xilinx LogiCORE PR
>> > Decoupler soft core.
>> >
>> > Signed-off-by: Moritz Fischer <mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>> > Signed-off-by: Michal Simek <michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>> > Acked-by: Alan Tull <atull-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>>
>> I'm confused why you are sending these instead of Moritz? If it goes
>> through you, then it should have your S-o-B too.

Greg asked me to send patches to him.  I should have started adding my
signed-of-by
at that point.

>
> Do you want me to resend this Alan (with Rob's suggestions)?

I sent a set of patches to Greg on March 24.  Looking back on that I realize
that it didn't have Rob's ack yet (as well as having my ack where it should
have been my signed-of-by).

Yes, please resend this patchset with Rob's feedback.

Thanks,
ALan

>>
>> > Cc: Sören Brinkmann <soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
>> > Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> > Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> > ---
>> >  .../bindings/fpga/xilinx-pr-decoupler.txt          | 35 ++++++++++++++++++++++
>> >  1 file changed, 35 insertions(+)
>> >  create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>> > new file mode 100644
>> > index 000000000000..2c527ac30398
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
>> > @@ -0,0 +1,35 @@
>> > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore
>> > +
>> > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more
>> > +decouplers / fpga bridges.
>> > +The controller can decouple/disable the bridges which prevents signal
>> > +changes from passing through the bridge.  The controller can also
>> > +couple / enable the bridges which allows traffic to pass through the
>> > +bridge normally.
>> > +
>> > +The Driver supports only MMIO handling. A PR region can have multiple
>> > +PR Decouplers which can be handled independently or chained via decouple/
>> > +decouple_status signals.
>> > +
>> > +Required properties:
>> > +- compatible : Should contain "xlnx,pr-decoupler-1.00" or "xlnx,pr-decoupler"
>>
>> I'd drop xlnx,pr-decoupler, but in any case, it should not be OR rather
>> "followed by". Plus the example has both.
>
> Michal wanted to have both, so I put both. Personally I don't care. I
> think they have some downstream stuff that relied on it.
>
>>
>> > +- regs : base address and size for decoupler module
>> > +- clocks : input clock to IP
>> > +- clock-names : should contain "aclk"
>> > +
>> > +Optional properties:
>> > +- bridge-enable : 0 if driver should disable bridge at startup
>> > +  1 if driver should enable bridge at startup
>> > +  Default is to leave bridge in current state.
>> > +
>> > +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
>> > +
>> > +Example:
>> > + fpga-bridge@100000450 {
>> > + compatible = "xlnx,pr-decoupler-1.00",
>> > +     "xlnx-pr-decoupler";
>> > + regs = <0x10000045 0x10>;
>> > + clocks = <&clkc 15>;
>> > + clock-names = "aclk";
>> > + bridge-enable = <0>;
>> > + };
>> > --
>> > 2.11.0
>> >
>> > --
>> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
> Thanks,
> Moritz
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html