[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[John Keeping]

This version is mostly small changes in response to review comments from
Sean and Chris, the details are in the individual patches.

I decided to drop the final patch which adds support for MIPI read
commands because I'm not using that feature now and I can't easily test
it.  It's on the list if anyone wants to pick it up in the future.

Version 3 was posted here:
http://www.spinics.net/lists/dri-devel/msg130977.html

Thanks to Sean Paul and Chris Zhong for their review and testing of this
series.

John Keeping (23):
  drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
    MIPI
  drm/rockchip: dw-mipi-dsi: pass mode in where needed
  drm/rockchip: dw-mipi-dsi: remove mode_set hook
  drm/rockchip: dw-mipi-dsi: fix command header writes
  drm/rockchip: dw-mipi-dsi: fix generic packet status check
  drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
  drm/rockchip: dw-mipi-dsi: include bad value in error message
  drm/rockchip: dw-mipi-dsi: respect message flags
  drm/rockchip: dw-mipi-dsi: only request HS clock when required
  drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
  drm/rockchip: dw-mipi-dsi: prepare panel after phy init
  drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
  drm/rockchip: dw-mipi-dsi: fix escape clock rate
  drm/rockchip: dw-mipi-dsi: ensure PHY is reset
  drm/rockchip: dw-mipi-dsi: configure PHY before enabling
  drm/rockchip: dw-mipi-dsi: properly configure PHY timing
  drm/rockchip: dw-mipi-dsi: improve PLL configuration
  drm/rockchip: dw-mipi-dsi: use specific poll helper
  drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
  drm/rockchip: vop: test for P{H,V}SYNC
  drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
  drm/rockchip: dw-mipi-dsi: support non-burst modes
  drm/rockchip: dw-mipi-dsi: add reset control

 drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
 2 files changed, 220 insertions(+), 109 deletions(-)

-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[John Keeping]

This version is mostly small changes in response to review comments from
Sean and Chris, the details are in the individual patches.

I decided to drop the final patch which adds support for MIPI read
commands because I'm not using that feature now and I can't easily test
it.  It's on the list if anyone wants to pick it up in the future.

Version 3 was posted here:
http://www.spinics.net/lists/dri-devel/msg130977.html

Thanks to Sean Paul and Chris Zhong for their review and testing of this
series.

John Keeping (23):
  drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
    MIPI
  drm/rockchip: dw-mipi-dsi: pass mode in where needed
  drm/rockchip: dw-mipi-dsi: remove mode_set hook
  drm/rockchip: dw-mipi-dsi: fix command header writes
  drm/rockchip: dw-mipi-dsi: fix generic packet status check
  drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
  drm/rockchip: dw-mipi-dsi: include bad value in error message
  drm/rockchip: dw-mipi-dsi: respect message flags
  drm/rockchip: dw-mipi-dsi: only request HS clock when required
  drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
  drm/rockchip: dw-mipi-dsi: prepare panel after phy init
  drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
  drm/rockchip: dw-mipi-dsi: fix escape clock rate
  drm/rockchip: dw-mipi-dsi: ensure PHY is reset
  drm/rockchip: dw-mipi-dsi: configure PHY before enabling
  drm/rockchip: dw-mipi-dsi: properly configure PHY timing
  drm/rockchip: dw-mipi-dsi: improve PLL configuration
  drm/rockchip: dw-mipi-dsi: use specific poll helper
  drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
  drm/rockchip: vop: test for P{H,V}SYNC
  drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
  drm/rockchip: dw-mipi-dsi: support non-burst modes
  drm/rockchip: dw-mipi-dsi: add reset control

 drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
 2 files changed, 220 insertions(+), 109 deletions(-)

-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[John Keeping]

This version is mostly small changes in response to review comments from
Sean and Chris, the details are in the individual patches.

I decided to drop the final patch which adds support for MIPI read
commands because I'm not using that feature now and I can't easily test
it.  It's on the list if anyone wants to pick it up in the future.

Version 3 was posted here:
http://www.spinics.net/lists/dri-devel/msg130977.html

Thanks to Sean Paul and Chris Zhong for their review and testing of this
series.

John Keeping (23):
  drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
    MIPI
  drm/rockchip: dw-mipi-dsi: pass mode in where needed
  drm/rockchip: dw-mipi-dsi: remove mode_set hook
  drm/rockchip: dw-mipi-dsi: fix command header writes
  drm/rockchip: dw-mipi-dsi: fix generic packet status check
  drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
  drm/rockchip: dw-mipi-dsi: include bad value in error message
  drm/rockchip: dw-mipi-dsi: respect message flags
  drm/rockchip: dw-mipi-dsi: only request HS clock when required
  drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
  drm/rockchip: dw-mipi-dsi: prepare panel after phy init
  drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
  drm/rockchip: dw-mipi-dsi: fix escape clock rate
  drm/rockchip: dw-mipi-dsi: ensure PHY is reset
  drm/rockchip: dw-mipi-dsi: configure PHY before enabling
  drm/rockchip: dw-mipi-dsi: properly configure PHY timing
  drm/rockchip: dw-mipi-dsi: improve PLL configuration
  drm/rockchip: dw-mipi-dsi: use specific poll helper
  drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
  drm/rockchip: vop: test for P{H,V}SYNC
  drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
  drm/rockchip: dw-mipi-dsi: support non-burst modes
  drm/rockchip: dw-mipi-dsi: add reset control

 drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
 2 files changed, 220 insertions(+), 109 deletions(-)

-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 01/23] drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for MIPI

[John Keeping]

With atomic modesetting the hardware will be powered off when the
mode_set function is called.  We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Squash together with the commit to s/commit/enable/
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 49 +++++++++++++++-------------------
 1 file changed, 21 insertions(+), 28 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index d9aa382bb629..bbd992299f73 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -819,34 +819,8 @@ static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
 					struct drm_display_mode *adjusted_mode)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-	int ret;
 
 	dsi->mode = adjusted_mode;
-
-	ret = dw_mipi_dsi_get_lane_bps(dsi);
-	if (ret < 0)
-		return;
-
-	if (clk_prepare_enable(dsi->pclk)) {
-		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
-		return;
-	}
-
-	dw_mipi_dsi_init(dsi);
-	dw_mipi_dsi_dpi_config(dsi, mode);
-	dw_mipi_dsi_packet_handler_config(dsi);
-	dw_mipi_dsi_video_mode_config(dsi);
-	dw_mipi_dsi_video_packet_config(dsi, mode);
-	dw_mipi_dsi_command_mode_config(dsi);
-	dw_mipi_dsi_line_timer_config(dsi);
-	dw_mipi_dsi_vertical_timing_config(dsi);
-	dw_mipi_dsi_dphy_timing_config(dsi);
-	dw_mipi_dsi_dphy_interface_config(dsi);
-	dw_mipi_dsi_clear_err(dsi);
-	if (drm_panel_prepare(dsi->panel))
-		dev_err(dsi->dev, "failed to prepare panel\n");
-
-	clk_disable_unprepare(dsi->pclk);
 }
 
 static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
@@ -875,17 +849,36 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 	clk_disable_unprepare(dsi->pclk);
 }
 
-static void dw_mipi_dsi_encoder_commit(struct drm_encoder *encoder)
+static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
+	int ret;
+
+	ret = dw_mipi_dsi_get_lane_bps(dsi);
+	if (ret < 0)
+		return;
 
 	if (clk_prepare_enable(dsi->pclk)) {
 		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
 		return;
 	}
 
+	dw_mipi_dsi_init(dsi);
+	dw_mipi_dsi_dpi_config(dsi, dsi->mode);
+	dw_mipi_dsi_packet_handler_config(dsi);
+	dw_mipi_dsi_video_mode_config(dsi);
+	dw_mipi_dsi_video_packet_config(dsi, dsi->mode);
+	dw_mipi_dsi_command_mode_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi);
+	dw_mipi_dsi_vertical_timing_config(dsi);
+	dw_mipi_dsi_dphy_timing_config(dsi);
+	dw_mipi_dsi_dphy_interface_config(dsi);
+	dw_mipi_dsi_clear_err(dsi);
+	if (drm_panel_prepare(dsi->panel))
+		dev_err(dsi->dev, "failed to prepare panel\n");
+
 	dw_mipi_dsi_phy_init(dsi);
 	dw_mipi_dsi_wait_for_two_frames(dsi);
 
@@ -933,7 +926,7 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
 
 static struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
-	.commit = dw_mipi_dsi_encoder_commit,
+	.enable = dw_mipi_dsi_encoder_enable,
 	.mode_set = dw_mipi_dsi_encoder_mode_set,
 	.disable = dw_mipi_dsi_encoder_disable,
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 01/23] drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for MIPI

[John Keeping]

With atomic modesetting the hardware will be powered off when the
mode_set function is called.  We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Squash together with the commit to s/commit/enable/
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 49 +++++++++++++++-------------------
 1 file changed, 21 insertions(+), 28 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index d9aa382bb629..bbd992299f73 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -819,34 +819,8 @@ static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
 					struct drm_display_mode *adjusted_mode)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-	int ret;
 
 	dsi->mode = adjusted_mode;
-
-	ret = dw_mipi_dsi_get_lane_bps(dsi);
-	if (ret < 0)
-		return;
-
-	if (clk_prepare_enable(dsi->pclk)) {
-		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
-		return;
-	}
-
-	dw_mipi_dsi_init(dsi);
-	dw_mipi_dsi_dpi_config(dsi, mode);
-	dw_mipi_dsi_packet_handler_config(dsi);
-	dw_mipi_dsi_video_mode_config(dsi);
-	dw_mipi_dsi_video_packet_config(dsi, mode);
-	dw_mipi_dsi_command_mode_config(dsi);
-	dw_mipi_dsi_line_timer_config(dsi);
-	dw_mipi_dsi_vertical_timing_config(dsi);
-	dw_mipi_dsi_dphy_timing_config(dsi);
-	dw_mipi_dsi_dphy_interface_config(dsi);
-	dw_mipi_dsi_clear_err(dsi);
-	if (drm_panel_prepare(dsi->panel))
-		dev_err(dsi->dev, "failed to prepare panel\n");
-
-	clk_disable_unprepare(dsi->pclk);
 }
 
 static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
@@ -875,17 +849,36 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 	clk_disable_unprepare(dsi->pclk);
 }
 
-static void dw_mipi_dsi_encoder_commit(struct drm_encoder *encoder)
+static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
+	int ret;
+
+	ret = dw_mipi_dsi_get_lane_bps(dsi);
+	if (ret < 0)
+		return;
 
 	if (clk_prepare_enable(dsi->pclk)) {
 		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
 		return;
 	}
 
+	dw_mipi_dsi_init(dsi);
+	dw_mipi_dsi_dpi_config(dsi, dsi->mode);
+	dw_mipi_dsi_packet_handler_config(dsi);
+	dw_mipi_dsi_video_mode_config(dsi);
+	dw_mipi_dsi_video_packet_config(dsi, dsi->mode);
+	dw_mipi_dsi_command_mode_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi);
+	dw_mipi_dsi_vertical_timing_config(dsi);
+	dw_mipi_dsi_dphy_timing_config(dsi);
+	dw_mipi_dsi_dphy_interface_config(dsi);
+	dw_mipi_dsi_clear_err(dsi);
+	if (drm_panel_prepare(dsi->panel))
+		dev_err(dsi->dev, "failed to prepare panel\n");
+
 	dw_mipi_dsi_phy_init(dsi);
 	dw_mipi_dsi_wait_for_two_frames(dsi);
 
@@ -933,7 +926,7 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
 
 static struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
-	.commit = dw_mipi_dsi_encoder_commit,
+	.enable = dw_mipi_dsi_encoder_enable,
 	.mode_set = dw_mipi_dsi_encoder_mode_set,
 	.disable = dw_mipi_dsi_encoder_disable,
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 01/23] drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for MIPI

[John Keeping]

With atomic modesetting the hardware will be powered off when the
mode_set function is called.  We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Squash together with the commit to s/commit/enable/
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 49 +++++++++++++++-------------------
 1 file changed, 21 insertions(+), 28 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index d9aa382bb629..bbd992299f73 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -819,34 +819,8 @@ static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
 					struct drm_display_mode *adjusted_mode)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-	int ret;
 
 	dsi->mode = adjusted_mode;
-
-	ret = dw_mipi_dsi_get_lane_bps(dsi);
-	if (ret < 0)
-		return;
-
-	if (clk_prepare_enable(dsi->pclk)) {
-		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
-		return;
-	}
-
-	dw_mipi_dsi_init(dsi);
-	dw_mipi_dsi_dpi_config(dsi, mode);
-	dw_mipi_dsi_packet_handler_config(dsi);
-	dw_mipi_dsi_video_mode_config(dsi);
-	dw_mipi_dsi_video_packet_config(dsi, mode);
-	dw_mipi_dsi_command_mode_config(dsi);
-	dw_mipi_dsi_line_timer_config(dsi);
-	dw_mipi_dsi_vertical_timing_config(dsi);
-	dw_mipi_dsi_dphy_timing_config(dsi);
-	dw_mipi_dsi_dphy_interface_config(dsi);
-	dw_mipi_dsi_clear_err(dsi);
-	if (drm_panel_prepare(dsi->panel))
-		dev_err(dsi->dev, "failed to prepare panel\n");
-
-	clk_disable_unprepare(dsi->pclk);
 }
 
 static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
@@ -875,17 +849,36 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 	clk_disable_unprepare(dsi->pclk);
 }
 
-static void dw_mipi_dsi_encoder_commit(struct drm_encoder *encoder)
+static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
+	int ret;
+
+	ret = dw_mipi_dsi_get_lane_bps(dsi);
+	if (ret < 0)
+		return;
 
 	if (clk_prepare_enable(dsi->pclk)) {
 		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
 		return;
 	}
 
+	dw_mipi_dsi_init(dsi);
+	dw_mipi_dsi_dpi_config(dsi, dsi->mode);
+	dw_mipi_dsi_packet_handler_config(dsi);
+	dw_mipi_dsi_video_mode_config(dsi);
+	dw_mipi_dsi_video_packet_config(dsi, dsi->mode);
+	dw_mipi_dsi_command_mode_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi);
+	dw_mipi_dsi_vertical_timing_config(dsi);
+	dw_mipi_dsi_dphy_timing_config(dsi);
+	dw_mipi_dsi_dphy_interface_config(dsi);
+	dw_mipi_dsi_clear_err(dsi);
+	if (drm_panel_prepare(dsi->panel))
+		dev_err(dsi->dev, "failed to prepare panel\n");
+
 	dw_mipi_dsi_phy_init(dsi);
 	dw_mipi_dsi_wait_for_two_frames(dsi);
 
@@ -933,7 +926,7 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
 
 static struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
-	.commit = dw_mipi_dsi_encoder_commit,
+	.enable = dw_mipi_dsi_encoder_enable,
 	.mode_set = dw_mipi_dsi_encoder_mode_set,
 	.disable = dw_mipi_dsi_encoder_disable,
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 02/23] drm/rockchip: dw-mipi-dsi: pass mode in where needed

[John Keeping]

This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
New in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 41 ++++++++++++++++++----------------
 1 file changed, 22 insertions(+), 19 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index bbd992299f73..cdbd25087e83 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -330,11 +330,11 @@ static int max_mbps_to_testdin(unsigned int max_mbps)
  * The controller should generate 2 frames before
  * preparing the peripheral.
  */
-static void dw_mipi_dsi_wait_for_two_frames(struct dw_mipi_dsi *dsi)
+static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode)
 {
 	int refresh, two_frames;
 
-	refresh = drm_mode_vrefresh(dsi->mode);
+	refresh = drm_mode_vrefresh(mode);
 	two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
 	msleep(two_frames);
 }
@@ -459,7 +459,8 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 	return ret;
 }
 
-static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi)
+static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi,
+				    struct drm_display_mode *mode)
 {
 	unsigned int i, pre;
 	unsigned long mpclk, pllref, tmp;
@@ -474,7 +475,7 @@ static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi)
 		return bpp;
 	}
 
-	mpclk = DIV_ROUND_UP(dsi->mode->clock, MSEC_PER_SEC);
+	mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC);
 	if (mpclk) {
 		/* take 1 / 0.9, since mbps must big than bandwidth of RGB */
 		tmp = mpclk * (bpp / dsi->lanes) * 10 / 9;
@@ -742,43 +743,44 @@ static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
 
 /* Get lane byte clock cycles. */
 static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
+					   struct drm_display_mode *mode,
 					   u32 hcomponent)
 {
 	u32 frac, lbcc;
 
 	lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
 
-	frac = lbcc % dsi->mode->clock;
-	lbcc = lbcc / dsi->mode->clock;
+	frac = lbcc % mode->clock;
+	lbcc = lbcc / mode->clock;
 	if (frac)
 		lbcc++;
 
 	return lbcc;
 }
 
-static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi)
+static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
+					  struct drm_display_mode *mode)
 {
 	u32 htotal, hsa, hbp, lbcc;
-	struct drm_display_mode *mode = dsi->mode;
 
 	htotal = mode->htotal;
 	hsa = mode->hsync_end - mode->hsync_start;
 	hbp = mode->htotal - mode->hsync_end;
 
-	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, htotal);
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
 	dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
 
-	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hsa);
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
 	dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
 
-	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hbp);
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
 	dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
 }
 
-static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi)
+static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
+					       struct drm_display_mode *mode)
 {
 	u32 vactive, vsa, vfp, vbp;
-	struct drm_display_mode *mode = dsi->mode;
 
 	vactive = mode->vdisplay;
 	vsa = mode->vsync_end - mode->vsync_start;
@@ -852,11 +854,12 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
+	struct drm_display_mode *mode = dsi->mode;
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
 	int ret;
 
-	ret = dw_mipi_dsi_get_lane_bps(dsi);
+	ret = dw_mipi_dsi_get_lane_bps(dsi, mode);
 	if (ret < 0)
 		return;
 
@@ -866,13 +869,13 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 	}
 
 	dw_mipi_dsi_init(dsi);
-	dw_mipi_dsi_dpi_config(dsi, dsi->mode);
+	dw_mipi_dsi_dpi_config(dsi, mode);
 	dw_mipi_dsi_packet_handler_config(dsi);
 	dw_mipi_dsi_video_mode_config(dsi);
-	dw_mipi_dsi_video_packet_config(dsi, dsi->mode);
+	dw_mipi_dsi_video_packet_config(dsi, mode);
 	dw_mipi_dsi_command_mode_config(dsi);
-	dw_mipi_dsi_line_timer_config(dsi);
-	dw_mipi_dsi_vertical_timing_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi, mode);
+	dw_mipi_dsi_vertical_timing_config(dsi, mode);
 	dw_mipi_dsi_dphy_timing_config(dsi);
 	dw_mipi_dsi_dphy_interface_config(dsi);
 	dw_mipi_dsi_clear_err(dsi);
@@ -880,7 +883,7 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 		dev_err(dsi->dev, "failed to prepare panel\n");
 
 	dw_mipi_dsi_phy_init(dsi);
-	dw_mipi_dsi_wait_for_two_frames(dsi);
+	dw_mipi_dsi_wait_for_two_frames(mode);
 
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 	drm_panel_enable(dsi->panel);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 02/23] drm/rockchip: dw-mipi-dsi: pass mode in where needed

[John Keeping]

This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
New in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 41 ++++++++++++++++++----------------
 1 file changed, 22 insertions(+), 19 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index bbd992299f73..cdbd25087e83 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -330,11 +330,11 @@ static int max_mbps_to_testdin(unsigned int max_mbps)
  * The controller should generate 2 frames before
  * preparing the peripheral.
  */
-static void dw_mipi_dsi_wait_for_two_frames(struct dw_mipi_dsi *dsi)
+static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode)
 {
 	int refresh, two_frames;
 
-	refresh = drm_mode_vrefresh(dsi->mode);
+	refresh = drm_mode_vrefresh(mode);
 	two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
 	msleep(two_frames);
 }
@@ -459,7 +459,8 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 	return ret;
 }
 
-static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi)
+static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi,
+				    struct drm_display_mode *mode)
 {
 	unsigned int i, pre;
 	unsigned long mpclk, pllref, tmp;
@@ -474,7 +475,7 @@ static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi)
 		return bpp;
 	}
 
-	mpclk = DIV_ROUND_UP(dsi->mode->clock, MSEC_PER_SEC);
+	mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC);
 	if (mpclk) {
 		/* take 1 / 0.9, since mbps must big than bandwidth of RGB */
 		tmp = mpclk * (bpp / dsi->lanes) * 10 / 9;
@@ -742,43 +743,44 @@ static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
 
 /* Get lane byte clock cycles. */
 static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
+					   struct drm_display_mode *mode,
 					   u32 hcomponent)
 {
 	u32 frac, lbcc;
 
 	lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
 
-	frac = lbcc % dsi->mode->clock;
-	lbcc = lbcc / dsi->mode->clock;
+	frac = lbcc % mode->clock;
+	lbcc = lbcc / mode->clock;
 	if (frac)
 		lbcc++;
 
 	return lbcc;
 }
 
-static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi)
+static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
+					  struct drm_display_mode *mode)
 {
 	u32 htotal, hsa, hbp, lbcc;
-	struct drm_display_mode *mode = dsi->mode;
 
 	htotal = mode->htotal;
 	hsa = mode->hsync_end - mode->hsync_start;
 	hbp = mode->htotal - mode->hsync_end;
 
-	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, htotal);
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
 	dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
 
-	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hsa);
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
 	dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
 
-	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hbp);
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
 	dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
 }
 
-static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi)
+static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
+					       struct drm_display_mode *mode)
 {
 	u32 vactive, vsa, vfp, vbp;
-	struct drm_display_mode *mode = dsi->mode;
 
 	vactive = mode->vdisplay;
 	vsa = mode->vsync_end - mode->vsync_start;
@@ -852,11 +854,12 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
+	struct drm_display_mode *mode = dsi->mode;
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
 	int ret;
 
-	ret = dw_mipi_dsi_get_lane_bps(dsi);
+	ret = dw_mipi_dsi_get_lane_bps(dsi, mode);
 	if (ret < 0)
 		return;
 
@@ -866,13 +869,13 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 	}
 
 	dw_mipi_dsi_init(dsi);
-	dw_mipi_dsi_dpi_config(dsi, dsi->mode);
+	dw_mipi_dsi_dpi_config(dsi, mode);
 	dw_mipi_dsi_packet_handler_config(dsi);
 	dw_mipi_dsi_video_mode_config(dsi);
-	dw_mipi_dsi_video_packet_config(dsi, dsi->mode);
+	dw_mipi_dsi_video_packet_config(dsi, mode);
 	dw_mipi_dsi_command_mode_config(dsi);
-	dw_mipi_dsi_line_timer_config(dsi);
-	dw_mipi_dsi_vertical_timing_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi, mode);
+	dw_mipi_dsi_vertical_timing_config(dsi, mode);
 	dw_mipi_dsi_dphy_timing_config(dsi);
 	dw_mipi_dsi_dphy_interface_config(dsi);
 	dw_mipi_dsi_clear_err(dsi);
@@ -880,7 +883,7 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 		dev_err(dsi->dev, "failed to prepare panel\n");
 
 	dw_mipi_dsi_phy_init(dsi);
-	dw_mipi_dsi_wait_for_two_frames(dsi);
+	dw_mipi_dsi_wait_for_two_frames(mode);
 
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 	drm_panel_enable(dsi->panel);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 03/23] drm/rockchip: dw-mipi-dsi: remove mode_set hook

[John Keeping]

This is not needed since we can access the mode via the CRTC from the
enable hook.  Also remove the "mode" field that is no longer used.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
New in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 13 +------------
 1 file changed, 1 insertion(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index cdbd25087e83..bd92e58b64f3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -286,7 +286,6 @@ struct dw_mipi_dsi {
 	u32 format;
 	u16 input_div;
 	u16 feedback_div;
-	struct drm_display_mode *mode;
 
 	const struct dw_mipi_dsi_plat_data *pdata;
 };
@@ -816,15 +815,6 @@ static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
 	dsi_write(dsi, DSI_INT_MSK1, 0);
 }
 
-static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
-					struct drm_display_mode *mode,
-					struct drm_display_mode *adjusted_mode)
-{
-	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-
-	dsi->mode = adjusted_mode;
-}
-
 static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
@@ -854,7 +844,7 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-	struct drm_display_mode *mode = dsi->mode;
+	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
 	int ret;
@@ -930,7 +920,6 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
 static struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
 	.enable = dw_mipi_dsi_encoder_enable,
-	.mode_set = dw_mipi_dsi_encoder_mode_set,
 	.disable = dw_mipi_dsi_encoder_disable,
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
 };
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 03/23] drm/rockchip: dw-mipi-dsi: remove mode_set hook

[John Keeping]

This is not needed since we can access the mode via the CRTC from the
enable hook.  Also remove the "mode" field that is no longer used.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
New in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 13 +------------
 1 file changed, 1 insertion(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index cdbd25087e83..bd92e58b64f3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -286,7 +286,6 @@ struct dw_mipi_dsi {
 	u32 format;
 	u16 input_div;
 	u16 feedback_div;
-	struct drm_display_mode *mode;
 
 	const struct dw_mipi_dsi_plat_data *pdata;
 };
@@ -816,15 +815,6 @@ static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
 	dsi_write(dsi, DSI_INT_MSK1, 0);
 }
 
-static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
-					struct drm_display_mode *mode,
-					struct drm_display_mode *adjusted_mode)
-{
-	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-
-	dsi->mode = adjusted_mode;
-}
-
 static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
@@ -854,7 +844,7 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-	struct drm_display_mode *mode = dsi->mode;
+	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
 	int ret;
@@ -930,7 +920,6 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
 static struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
 	.enable = dw_mipi_dsi_encoder_enable,
-	.mode_set = dw_mipi_dsi_encoder_mode_set,
 	.disable = dw_mipi_dsi_encoder_disable,
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
 };
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 03/23] drm/rockchip: dw-mipi-dsi: remove mode_set hook

[John Keeping]

This is not needed since we can access the mode via the CRTC from the
enable hook.  Also remove the "mode" field that is no longer used.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
New in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 13 +------------
 1 file changed, 1 insertion(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index cdbd25087e83..bd92e58b64f3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -286,7 +286,6 @@ struct dw_mipi_dsi {
 	u32 format;
 	u16 input_div;
 	u16 feedback_div;
-	struct drm_display_mode *mode;
 
 	const struct dw_mipi_dsi_plat_data *pdata;
 };
@@ -816,15 +815,6 @@ static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
 	dsi_write(dsi, DSI_INT_MSK1, 0);
 }
 
-static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
-					struct drm_display_mode *mode,
-					struct drm_display_mode *adjusted_mode)
-{
-	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-
-	dsi->mode = adjusted_mode;
-}
-
 static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
@@ -854,7 +844,7 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-	struct drm_display_mode *mode = dsi->mode;
+	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
 	int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
 	u32 val;
 	int ret;
@@ -930,7 +920,6 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
 static struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
 	.enable = dw_mipi_dsi_encoder_enable,
-	.mode_set = dw_mipi_dsi_encoder_mode_set,
 	.disable = dw_mipi_dsi_encoder_disable,
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
 };
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 04/23] drm/rockchip: dw-mipi-dsi: fix command header writes

[John Keeping]

In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it.  Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.

Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index bd92e58b64f3..4cbbbcb619b7 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -542,9 +542,10 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 	return 0;
 }
 
-static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
+static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
+	u32 val;
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
@@ -554,7 +555,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
 		return ret;
 	}
 
-	dsi_write(dsi, DSI_GEN_HDR, val);
+	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
@@ -587,8 +588,9 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 {
 	const u32 *tx_buf = msg->tx_buf;
 	int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
-	u32 val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
+	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
 	u32 remainder = 0;
+	u32 val;
 
 	if (msg->tx_len < 3) {
 		dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
@@ -617,7 +619,7 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 		}
 	}
 
-	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
+	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
 }
 
 static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 04/23] drm/rockchip: dw-mipi-dsi: fix command header writes

[John Keeping]

In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it.  Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.

Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index bd92e58b64f3..4cbbbcb619b7 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -542,9 +542,10 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 	return 0;
 }
 
-static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
+static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
+	u32 val;
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
@@ -554,7 +555,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
 		return ret;
 	}
 
-	dsi_write(dsi, DSI_GEN_HDR, val);
+	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
@@ -587,8 +588,9 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 {
 	const u32 *tx_buf = msg->tx_buf;
 	int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
-	u32 val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
+	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
 	u32 remainder = 0;
+	u32 val;
 
 	if (msg->tx_len < 3) {
 		dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
@@ -617,7 +619,7 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 		}
 	}
 
-	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
+	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
 }
 
 static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 04/23] drm/rockchip: dw-mipi-dsi: fix command header writes

[John Keeping]

In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it.  Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.

Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index bd92e58b64f3..4cbbbcb619b7 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -542,9 +542,10 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 	return 0;
 }
 
-static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
+static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
+	u32 val;
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
@@ -554,7 +555,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
 		return ret;
 	}
 
-	dsi_write(dsi, DSI_GEN_HDR, val);
+	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
@@ -587,8 +588,9 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 {
 	const u32 *tx_buf = msg->tx_buf;
 	int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
-	u32 val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
+	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
 	u32 remainder = 0;
+	u32 val;
 
 	if (msg->tx_len < 3) {
 		dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
@@ -617,7 +619,7 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 		}
 	}
 
-	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
+	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
 }
 
 static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 05/23] drm/rockchip: dw-mipi-dsi: fix generic packet status check

[John Keeping]

We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4cbbbcb619b7..4be1ff3a42bb 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -545,7 +545,7 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
-	u32 val;
+	u32 val, mask;
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
@@ -557,8 +557,9 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 
 	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
+	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
-				 val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
+				 val, (val & mask) == mask,
 				 1000, CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
 		dev_err(dsi->dev, "failed to write command FIFO\n");
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 05/23] drm/rockchip: dw-mipi-dsi: fix generic packet status check

[John Keeping]

We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4cbbbcb619b7..4be1ff3a42bb 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -545,7 +545,7 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
-	u32 val;
+	u32 val, mask;
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
@@ -557,8 +557,9 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 
 	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
+	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
-				 val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
+				 val, (val & mask) == mask,
 				 1000, CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
 		dev_err(dsi->dev, "failed to write command FIFO\n");
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 05/23] drm/rockchip: dw-mipi-dsi: fix generic packet status check

[John Keeping]

We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4cbbbcb619b7..4be1ff3a42bb 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -545,7 +545,7 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
-	u32 val;
+	u32 val, mask;
 
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
@@ -557,8 +557,9 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 
 	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
+	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
 	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
-				 val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
+				 val, (val & mask) == mask,
 				 1000, CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
 		dev_err(dsi->dev, "failed to write command FIFO\n");
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 06/23] drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf

[John Keeping]

As a side-effect of this, encode the endianness explicitly rather than
casting a u16.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Introduce "data" variable to avoid confusion around the masking in
  GEN_HDATA()
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4be1ff3a42bb..f55010312f25 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -572,8 +572,14 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 				       const struct mipi_dsi_msg *msg)
 {
-	const u16 *tx_buf = msg->tx_buf;
-	u32 val = GEN_HDATA(*tx_buf) | GEN_HTYPE(msg->type);
+	const u8 *tx_buf = msg->tx_buf;
+	u16 data = 0;
+	u32 val;
+
+	if (msg->tx_len > 0)
+		data |= tx_buf[0];
+	if (msg->tx_len > 1)
+		data |= tx_buf[1] << 8;
 
 	if (msg->tx_len > 2) {
 		dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
@@ -581,6 +587,7 @@ static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 		return -EINVAL;
 	}
 
+	val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
 	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
 }
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 06/23] drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf

[John Keeping]

As a side-effect of this, encode the endianness explicitly rather than
casting a u16.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Introduce "data" variable to avoid confusion around the masking in
  GEN_HDATA()
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4be1ff3a42bb..f55010312f25 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -572,8 +572,14 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 				       const struct mipi_dsi_msg *msg)
 {
-	const u16 *tx_buf = msg->tx_buf;
-	u32 val = GEN_HDATA(*tx_buf) | GEN_HTYPE(msg->type);
+	const u8 *tx_buf = msg->tx_buf;
+	u16 data = 0;
+	u32 val;
+
+	if (msg->tx_len > 0)
+		data |= tx_buf[0];
+	if (msg->tx_len > 1)
+		data |= tx_buf[1] << 8;
 
 	if (msg->tx_len > 2) {
 		dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
@@ -581,6 +587,7 @@ static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 		return -EINVAL;
 	}
 
+	val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
 	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
 }
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 06/23] drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf

[John Keeping]

As a side-effect of this, encode the endianness explicitly rather than
casting a u16.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Introduce "data" variable to avoid confusion around the masking in
  GEN_HDATA()
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4be1ff3a42bb..f55010312f25 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -572,8 +572,14 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 				       const struct mipi_dsi_msg *msg)
 {
-	const u16 *tx_buf = msg->tx_buf;
-	u32 val = GEN_HDATA(*tx_buf) | GEN_HTYPE(msg->type);
+	const u8 *tx_buf = msg->tx_buf;
+	u16 data = 0;
+	u32 val;
+
+	if (msg->tx_len > 0)
+		data |= tx_buf[0];
+	if (msg->tx_len > 1)
+		data |= tx_buf[1] << 8;
 
 	if (msg->tx_len > 2) {
 		dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
@@ -581,6 +587,7 @@ static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 		return -EINVAL;
 	}
 
+	val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
 	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
 }
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 07/23] drm/rockchip: dw-mipi-dsi: include bad value in error message

[John Keeping]

As an aid to debugging.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index f55010312f25..374b18c550fd 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -646,7 +646,8 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
 		ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
 		break;
 	default:
-		dev_err(dsi->dev, "unsupported message type\n");
+		dev_err(dsi->dev, "unsupported message type 0x%02x\n",
+			msg->type);
 		ret = -EINVAL;
 	}
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 07/23] drm/rockchip: dw-mipi-dsi: include bad value in error message

[John Keeping]

As an aid to debugging.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index f55010312f25..374b18c550fd 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -646,7 +646,8 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
 		ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
 		break;
 	default:
-		dev_err(dsi->dev, "unsupported message type\n");
+		dev_err(dsi->dev, "unsupported message type 0x%02x\n",
+			msg->type);
 		ret = -EINVAL;
 	}
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 08/23] drm/rockchip: dw-mipi-dsi: respect message flags

[John Keeping]

Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message.  Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 374b18c550fd..a20d669b73ee 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -542,6 +542,19 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 	return 0;
 }
 
+static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
+				   const struct mipi_dsi_msg *msg)
+{
+	u32 val = 0;
+
+	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
+		val |= EN_ACK_RQST;
+	if (msg->flags & MIPI_DSI_MSG_USE_LPM)
+		val |= CMD_MODE_ALL_LP;
+
+	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
+}
+
 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
@@ -636,6 +649,8 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
 	struct dw_mipi_dsi *dsi = host_to_dsi(host);
 	int ret;
 
+	dw_mipi_message_config(dsi, msg);
+
 	switch (msg->type) {
 	case MIPI_DSI_DCS_SHORT_WRITE:
 	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
@@ -747,7 +762,6 @@ static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
 {
 	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
 	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
-	dsi_write(dsi, DSI_CMD_MODE_CFG, CMD_MODE_ALL_LP);
 	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
 }
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 08/23] drm/rockchip: dw-mipi-dsi: respect message flags

[John Keeping]

Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message.  Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 374b18c550fd..a20d669b73ee 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -542,6 +542,19 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 	return 0;
 }
 
+static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
+				   const struct mipi_dsi_msg *msg)
+{
+	u32 val = 0;
+
+	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
+		val |= EN_ACK_RQST;
+	if (msg->flags & MIPI_DSI_MSG_USE_LPM)
+		val |= CMD_MODE_ALL_LP;
+
+	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
+}
+
 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
@@ -636,6 +649,8 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
 	struct dw_mipi_dsi *dsi = host_to_dsi(host);
 	int ret;
 
+	dw_mipi_message_config(dsi, msg);
+
 	switch (msg->type) {
 	case MIPI_DSI_DCS_SHORT_WRITE:
 	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
@@ -747,7 +762,6 @@ static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
 {
 	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
 	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
-	dsi_write(dsi, DSI_CMD_MODE_CFG, CMD_MODE_ALL_LP);
 	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
 }
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 08/23] drm/rockchip: dw-mipi-dsi: respect message flags

[John Keeping]

Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message.  Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 374b18c550fd..a20d669b73ee 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -542,6 +542,19 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 	return 0;
 }
 
+static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
+				   const struct mipi_dsi_msg *msg)
+{
+	u32 val = 0;
+
+	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
+		val |= EN_ACK_RQST;
+	if (msg->flags & MIPI_DSI_MSG_USE_LPM)
+		val |= CMD_MODE_ALL_LP;
+
+	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
+}
+
 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 {
 	int ret;
@@ -636,6 +649,8 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
 	struct dw_mipi_dsi *dsi = host_to_dsi(host);
 	int ret;
 
+	dw_mipi_message_config(dsi, msg);
+
 	switch (msg->type) {
 	case MIPI_DSI_DCS_SHORT_WRITE:
 	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
@@ -747,7 +762,6 @@ static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
 {
 	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
 	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
-	dsi_write(dsi, DSI_CMD_MODE_CFG, CMD_MODE_ALL_LP);
 	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
 }
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 09/23] drm/rockchip: dw-mipi-dsi: only request HS clock when required

[John Keeping]

Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured.  The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index a20d669b73ee..1b6fce2600f3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -545,13 +545,15 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
 				   const struct mipi_dsi_msg *msg)
 {
+	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
 	u32 val = 0;
 
 	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
 		val |= EN_ACK_RQST;
-	if (msg->flags & MIPI_DSI_MSG_USE_LPM)
+	if (lpm)
 		val |= CMD_MODE_ALL_LP;
 
+	dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS);
 	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
 }
 
@@ -695,6 +697,7 @@ static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
 		dsi_write(dsi, DSI_PWR_UP, RESET);
 		dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
 		dw_mipi_dsi_video_mode_config(dsi);
+		dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
 		dsi_write(dsi, DSI_PWR_UP, POWERUP);
 	}
 }
@@ -712,7 +715,6 @@ static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
 		  | PHY_RSTZ | PHY_SHUTDOWNZ);
 	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
 		  TX_ESC_CLK_DIVIDSION(7));
-	dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
 }
 
 static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 09/23] drm/rockchip: dw-mipi-dsi: only request HS clock when required

[John Keeping]

Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured.  The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index a20d669b73ee..1b6fce2600f3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -545,13 +545,15 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
 static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
 				   const struct mipi_dsi_msg *msg)
 {
+	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
 	u32 val = 0;
 
 	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
 		val |= EN_ACK_RQST;
-	if (msg->flags & MIPI_DSI_MSG_USE_LPM)
+	if (lpm)
 		val |= CMD_MODE_ALL_LP;
 
+	dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS);
 	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
 }
 
@@ -695,6 +697,7 @@ static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
 		dsi_write(dsi, DSI_PWR_UP, RESET);
 		dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
 		dw_mipi_dsi_video_mode_config(dsi);
+		dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
 		dsi_write(dsi, DSI_PWR_UP, POWERUP);
 	}
 }
@@ -712,7 +715,6 @@ static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
 		  | PHY_RSTZ | PHY_SHUTDOWNZ);
 	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
 		  TX_ESC_CLK_DIVIDSION(7));
-	dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
 }
 
 static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 10/23] drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned

[John Keeping]

By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case.  Copy it into a
stack variable that will be correctly aligned.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
---
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 1b6fce2600f3..0c66e6eaf44a 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -609,10 +609,10 @@ static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 				      const struct mipi_dsi_msg *msg)
 {
-	const u32 *tx_buf = msg->tx_buf;
-	int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
+	const u8 *tx_buf = msg->tx_buf;
+	int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
 	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
-	u32 remainder = 0;
+	u32 remainder;
 	u32 val;
 
 	if (msg->tx_len < 3) {
@@ -623,12 +623,14 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 
 	while (DIV_ROUND_UP(len, pld_data_bytes)) {
 		if (len < pld_data_bytes) {
+			remainder = 0;
 			memcpy(&remainder, tx_buf, len);
 			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
 			len = 0;
 		} else {
-			dsi_write(dsi, DSI_GEN_PLD_DATA, *tx_buf);
-			tx_buf++;
+			memcpy(&remainder, tx_buf, pld_data_bytes);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
+			tx_buf += pld_data_bytes;
 			len -= pld_data_bytes;
 		}
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 10/23] drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned

[John Keeping]

By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case.  Copy it into a
stack variable that will be correctly aligned.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
---
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 1b6fce2600f3..0c66e6eaf44a 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -609,10 +609,10 @@ static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 				      const struct mipi_dsi_msg *msg)
 {
-	const u32 *tx_buf = msg->tx_buf;
-	int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
+	const u8 *tx_buf = msg->tx_buf;
+	int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
 	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
-	u32 remainder = 0;
+	u32 remainder;
 	u32 val;
 
 	if (msg->tx_len < 3) {
@@ -623,12 +623,14 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 
 	while (DIV_ROUND_UP(len, pld_data_bytes)) {
 		if (len < pld_data_bytes) {
+			remainder = 0;
 			memcpy(&remainder, tx_buf, len);
 			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
 			len = 0;
 		} else {
-			dsi_write(dsi, DSI_GEN_PLD_DATA, *tx_buf);
-			tx_buf++;
+			memcpy(&remainder, tx_buf, pld_data_bytes);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
+			tx_buf += pld_data_bytes;
 			len -= pld_data_bytes;
 		}
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 10/23] drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned

[John Keeping]

By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case.  Copy it into a
stack variable that will be correctly aligned.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
---
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 1b6fce2600f3..0c66e6eaf44a 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -609,10 +609,10 @@ static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
 static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 				      const struct mipi_dsi_msg *msg)
 {
-	const u32 *tx_buf = msg->tx_buf;
-	int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
+	const u8 *tx_buf = msg->tx_buf;
+	int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
 	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
-	u32 remainder = 0;
+	u32 remainder;
 	u32 val;
 
 	if (msg->tx_len < 3) {
@@ -623,12 +623,14 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 
 	while (DIV_ROUND_UP(len, pld_data_bytes)) {
 		if (len < pld_data_bytes) {
+			remainder = 0;
 			memcpy(&remainder, tx_buf, len);
 			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
 			len = 0;
 		} else {
-			dsi_write(dsi, DSI_GEN_PLD_DATA, *tx_buf);
-			tx_buf++;
+			memcpy(&remainder, tx_buf, pld_data_bytes);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
+			tx_buf += pld_data_bytes;
 			len -= pld_data_bytes;
 		}
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 11/23] drm/rockchip: dw-mipi-dsi: prepare panel after phy init

[John Keeping]

Some panels need to be configured with commands sent over the MIPI link,
which they will do in the prepare hook.  Call this after the PHY has
been initialized so that we are able to send commands to the panel.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0c66e6eaf44a..53515404d0ca 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -898,12 +898,14 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 	dw_mipi_dsi_dphy_timing_config(dsi);
 	dw_mipi_dsi_dphy_interface_config(dsi);
 	dw_mipi_dsi_clear_err(dsi);
-	if (drm_panel_prepare(dsi->panel))
-		dev_err(dsi->dev, "failed to prepare panel\n");
 
 	dw_mipi_dsi_phy_init(dsi);
 	dw_mipi_dsi_wait_for_two_frames(mode);
 
+	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
+	if (drm_panel_prepare(dsi->panel))
+		dev_err(dsi->dev, "failed to prepare panel\n");
+
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 	drm_panel_enable(dsi->panel);
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 11/23] drm/rockchip: dw-mipi-dsi: prepare panel after phy init

[John Keeping]

Some panels need to be configured with commands sent over the MIPI link,
which they will do in the prepare hook.  Call this after the PHY has
been initialized so that we are able to send commands to the panel.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0c66e6eaf44a..53515404d0ca 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -898,12 +898,14 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
 	dw_mipi_dsi_dphy_timing_config(dsi);
 	dw_mipi_dsi_dphy_interface_config(dsi);
 	dw_mipi_dsi_clear_err(dsi);
-	if (drm_panel_prepare(dsi->panel))
-		dev_err(dsi->dev, "failed to prepare panel\n");
 
 	dw_mipi_dsi_phy_init(dsi);
 	dw_mipi_dsi_wait_for_two_frames(mode);
 
+	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
+	if (drm_panel_prepare(dsi->panel))
+		dev_err(dsi->dev, "failed to prepare panel\n");
+
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 	drm_panel_enable(dsi->panel);
 
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 12/23] drm/rockchip: dw-mipi-dsi: allow commands in panel_disable

[John Keeping]

Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends.  In order
to send commands we need to write to registers, so pclk must be enabled.

While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 53515404d0ca..4201a2143295 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -848,24 +848,16 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
 
-	drm_panel_disable(dsi->panel);
-
 	if (clk_prepare_enable(dsi->pclk)) {
 		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
 		return;
 	}
 
+	drm_panel_disable(dsi->panel);
+
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
 	drm_panel_unprepare(dsi->panel);
-	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 
-	/*
-	 * This is necessary to make sure the peripheral will be driven
-	 * normally when the display is enabled again later.
-	 */
-	msleep(120);
-
-	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
 	dw_mipi_dsi_disable(dsi);
 	clk_disable_unprepare(dsi->pclk);
 }
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 12/23] drm/rockchip: dw-mipi-dsi: allow commands in panel_disable

[John Keeping]

Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends.  In order
to send commands we need to write to registers, so pclk must be enabled.

While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 53515404d0ca..4201a2143295 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -848,24 +848,16 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
 
-	drm_panel_disable(dsi->panel);
-
 	if (clk_prepare_enable(dsi->pclk)) {
 		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
 		return;
 	}
 
+	drm_panel_disable(dsi->panel);
+
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
 	drm_panel_unprepare(dsi->panel);
-	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 
-	/*
-	 * This is necessary to make sure the peripheral will be driven
-	 * normally when the display is enabled again later.
-	 */
-	msleep(120);
-
-	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
 	dw_mipi_dsi_disable(dsi);
 	clk_disable_unprepare(dsi->pclk);
 }
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 12/23] drm/rockchip: dw-mipi-dsi: allow commands in panel_disable

[John Keeping]

Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends.  In order
to send commands we need to write to registers, so pclk must be enabled.

While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 53515404d0ca..4201a2143295 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -848,24 +848,16 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
 {
 	struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
 
-	drm_panel_disable(dsi->panel);
-
 	if (clk_prepare_enable(dsi->pclk)) {
 		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
 		return;
 	}
 
+	drm_panel_disable(dsi->panel);
+
 	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
 	drm_panel_unprepare(dsi->panel);
-	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
 
-	/*
-	 * This is necessary to make sure the peripheral will be driven
-	 * normally when the display is enabled again later.
-	 */
-	msleep(120);
-
-	dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
 	dw_mipi_dsi_disable(dsi);
 	clk_disable_unprepare(dsi->pclk);
 }
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 13/23] drm/rockchip: dw-mipi-dsi: fix escape clock rate

[John Keeping]

This clock rate is derived from the PHY PLL, so it should be calculated
dynamically.  This calculation is the same as that used by the vendor
kernel and ensures that the escape clock runs at <20MHz as required by
the MIPI specification.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add a comment explaining the calculation and reword the commit message
  so that the calculation doesn't seem so magical
- Add Sean's Reviewed-by
v3:
- Improve the commit message a bit
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4201a2143295..0f9be41f0361 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -712,11 +712,21 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
 
 static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
 {
+	/*
+	 * The maximum permitted escape clock is 20MHz and it is derived from
+	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
+	 *
+	 *     (lane_mbps >> 3) / esc_clk_division < 20
+	 * which is:
+	 *     (lane_mbps >> 3) / 20 > esc_clk_division
+	 */
+	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
+
 	dsi_write(dsi, DSI_PWR_UP, RESET);
 	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
 		  | PHY_RSTZ | PHY_SHUTDOWNZ);
 	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
-		  TX_ESC_CLK_DIVIDSION(7));
+		  TX_ESC_CLK_DIVIDSION(esc_clk_division));
 }
 
 static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 13/23] drm/rockchip: dw-mipi-dsi: fix escape clock rate

[John Keeping]

This clock rate is derived from the PHY PLL, so it should be calculated
dynamically.  This calculation is the same as that used by the vendor
kernel and ensures that the escape clock runs at <20MHz as required by
the MIPI specification.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add a comment explaining the calculation and reword the commit message
  so that the calculation doesn't seem so magical
- Add Sean's Reviewed-by
v3:
- Improve the commit message a bit
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4201a2143295..0f9be41f0361 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -712,11 +712,21 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
 
 static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
 {
+	/*
+	 * The maximum permitted escape clock is 20MHz and it is derived from
+	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
+	 *
+	 *     (lane_mbps >> 3) / esc_clk_division < 20
+	 * which is:
+	 *     (lane_mbps >> 3) / 20 > esc_clk_division
+	 */
+	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
+
 	dsi_write(dsi, DSI_PWR_UP, RESET);
 	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
 		  | PHY_RSTZ | PHY_SHUTDOWNZ);
 	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
-		  TX_ESC_CLK_DIVIDSION(7));
+		  TX_ESC_CLK_DIVIDSION(esc_clk_division));
 }
 
 static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 13/23] drm/rockchip: dw-mipi-dsi: fix escape clock rate

[John Keeping]

This clock rate is derived from the PHY PLL, so it should be calculated
dynamically.  This calculation is the same as that used by the vendor
kernel and ensures that the escape clock runs at <20MHz as required by
the MIPI specification.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add a comment explaining the calculation and reword the commit message
  so that the calculation doesn't seem so magical
- Add Sean's Reviewed-by
v3:
- Improve the commit message a bit
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4201a2143295..0f9be41f0361 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -712,11 +712,21 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
 
 static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
 {
+	/*
+	 * The maximum permitted escape clock is 20MHz and it is derived from
+	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
+	 *
+	 *     (lane_mbps >> 3) / esc_clk_division < 20
+	 * which is:
+	 *     (lane_mbps >> 3) / 20 > esc_clk_division
+	 */
+	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
+
 	dsi_write(dsi, DSI_PWR_UP, RESET);
 	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
 		  | PHY_RSTZ | PHY_SHUTDOWNZ);
 	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
-		  TX_ESC_CLK_DIVIDSION(7));
+		  TX_ESC_CLK_DIVIDSION(esc_clk_division));
 }
 
 static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 14/23] drm/rockchip: dw-mipi-dsi: ensure PHY is reset

[John Keeping]

Also don't power up the DSI host at this point since this is not
necessary in order to configure the PHY and we do so later when
selecting video or command mode.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0f9be41f0361..78d676b7e516 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -397,7 +397,10 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 		return testdin;
 	}
 
-	dsi_write(dsi, DSI_PWR_UP, POWERUP);
+	/* Start by clearing PHY state */
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
 
 	dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE |
 					 VCO_RANGE_CON_SEL(vco) |
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 14/23] drm/rockchip: dw-mipi-dsi: ensure PHY is reset

[John Keeping]

Also don't power up the DSI host at this point since this is not
necessary in order to configure the PHY and we do so later when
selecting video or command mode.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0f9be41f0361..78d676b7e516 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -397,7 +397,10 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 		return testdin;
 	}
 
-	dsi_write(dsi, DSI_PWR_UP, POWERUP);
+	/* Start by clearing PHY state */
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
 
 	dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE |
 					 VCO_RANGE_CON_SEL(vco) |
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 14/23] drm/rockchip: dw-mipi-dsi: ensure PHY is reset

[John Keeping]

Also don't power up the DSI host at this point since this is not
necessary in order to configure the PHY and we do so later when
selecting video or command mode.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0f9be41f0361..78d676b7e516 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -397,7 +397,10 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 		return testdin;
 	}
 
-	dsi_write(dsi, DSI_PWR_UP, POWERUP);
+	/* Start by clearing PHY state */
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
 
 	dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE |
 					 VCO_RANGE_CON_SEL(vco) |
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 15/23] drm/rockchip: dw-mipi-dsi: configure PHY before enabling

[John Keeping]

The bias, bandgap and PLL should all be configured before we enable
them.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Squash together two patches that both affect initialization order of
  the PHY
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 78d676b7e516..4fee5176c606 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -413,12 +413,17 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 
 	dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin));
 
-	dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
 	dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div));
 	dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) |
 					 LOW_PROGRAM_EN);
 	dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) |
 					 HIGH_PROGRAM_EN);
+	dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
+
+	dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
+					 BIASEXTR_SEL(BIASEXTR_127_7));
+	dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
+					 BANDGAP_SEL(BANDGAP_96_10));
 
 	dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT |
 					 BIAS_BLOCK_ON | BANDGAP_ON);
@@ -429,10 +434,6 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 					 SETRD_MAX | POWER_MANAGE |
 					 TER_RESISTORS_ON);
 
-	dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
-					 BIASEXTR_SEL(BIASEXTR_127_7));
-	dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
-					 BANDGAP_SEL(BANDGAP_96_10));
 
 	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
 	dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 15/23] drm/rockchip: dw-mipi-dsi: configure PHY before enabling

[John Keeping]

The bias, bandgap and PLL should all be configured before we enable
them.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Squash together two patches that both affect initialization order of
  the PHY
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 78d676b7e516..4fee5176c606 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -413,12 +413,17 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 
 	dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin));
 
-	dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
 	dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div));
 	dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) |
 					 LOW_PROGRAM_EN);
 	dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) |
 					 HIGH_PROGRAM_EN);
+	dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
+
+	dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
+					 BIASEXTR_SEL(BIASEXTR_127_7));
+	dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
+					 BANDGAP_SEL(BANDGAP_96_10));
 
 	dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT |
 					 BIAS_BLOCK_ON | BANDGAP_ON);
@@ -429,10 +434,6 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 					 SETRD_MAX | POWER_MANAGE |
 					 TER_RESISTORS_ON);
 
-	dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
-					 BIASEXTR_SEL(BIASEXTR_127_7));
-	dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
-					 BANDGAP_SEL(BANDGAP_96_10));
 
 	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
 	dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 15/23] drm/rockchip: dw-mipi-dsi: configure PHY before enabling

[John Keeping]

The bias, bandgap and PLL should all be configured before we enable
them.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Squash together two patches that both affect initialization order of
  the PHY
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 78d676b7e516..4fee5176c606 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -413,12 +413,17 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 
 	dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin));
 
-	dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
 	dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div));
 	dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) |
 					 LOW_PROGRAM_EN);
 	dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) |
 					 HIGH_PROGRAM_EN);
+	dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
+
+	dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
+					 BIASEXTR_SEL(BIASEXTR_127_7));
+	dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
+					 BANDGAP_SEL(BANDGAP_96_10));
 
 	dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT |
 					 BIAS_BLOCK_ON | BANDGAP_ON);
@@ -429,10 +434,6 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 					 SETRD_MAX | POWER_MANAGE |
 					 TER_RESISTORS_ON);
 
-	dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
-					 BIASEXTR_SEL(BIASEXTR_127_7));
-	dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
-					 BANDGAP_SEL(BANDGAP_96_10));
 
 	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
 	dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 16/23] drm/rockchip: dw-mipi-dsi: properly configure PHY timing

[John Keeping]

These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.

Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Simplify ns2bc and ns2ui calculations as suggested by Sean Paul
v3:
- Wrap some long lines
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 35 ++++++++++++++++++++++++++++++----
 1 file changed, 31 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4fee5176c606..9b6a60deb69e 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -383,6 +383,22 @@ static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code,
 	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
 }
 
+/**
+ * ns2bc - Nanoseconds to byte clock cycles
+ */
+static inline unsigned int ns2bc(struct dw_mipi_dsi *dsi, int ns)
+{
+	return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000);
+}
+
+/**
+ * ns2ui - Nanoseconds to UI time periods
+ */
+static inline unsigned int ns2ui(struct dw_mipi_dsi *dsi, int ns)
+{
+	return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000);
+}
+
 static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 {
 	int ret, testdin, vco, val;
@@ -434,10 +450,21 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 					 SETRD_MAX | POWER_MANAGE |
 					 TER_RESISTORS_ON);
 
-
-	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
-	dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
-	dw_mipi_dsi_phy_write(dsi, 0x72, THS_ZERO_PROGRAM_EN | 0xa);
+	dw_mipi_dsi_phy_write(dsi, 0x60, TLP_PROGRAM_EN | ns2bc(dsi, 500));
+	dw_mipi_dsi_phy_write(dsi, 0x61, THS_PRE_PROGRAM_EN | ns2ui(dsi, 40));
+	dw_mipi_dsi_phy_write(dsi, 0x62, THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300));
+	dw_mipi_dsi_phy_write(dsi, 0x63, THS_PRE_PROGRAM_EN | ns2ui(dsi, 100));
+	dw_mipi_dsi_phy_write(dsi, 0x64, BIT(5) | ns2bc(dsi, 100));
+	dw_mipi_dsi_phy_write(dsi, 0x65, BIT(5) | (ns2bc(dsi, 60) + 7));
+
+	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | ns2bc(dsi, 500));
+	dw_mipi_dsi_phy_write(dsi, 0x71,
+			      THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 5));
+	dw_mipi_dsi_phy_write(dsi, 0x72,
+			      THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2));
+	dw_mipi_dsi_phy_write(dsi, 0x73,
+			      THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8));
+	dw_mipi_dsi_phy_write(dsi, 0x74, BIT(5) | ns2bc(dsi, 100));
 
 	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
 				     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 16/23] drm/rockchip: dw-mipi-dsi: properly configure PHY timing

[John Keeping]

These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.

Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Simplify ns2bc and ns2ui calculations as suggested by Sean Paul
v3:
- Wrap some long lines
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 35 ++++++++++++++++++++++++++++++----
 1 file changed, 31 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4fee5176c606..9b6a60deb69e 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -383,6 +383,22 @@ static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code,
 	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
 }
 
+/**
+ * ns2bc - Nanoseconds to byte clock cycles
+ */
+static inline unsigned int ns2bc(struct dw_mipi_dsi *dsi, int ns)
+{
+	return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000);
+}
+
+/**
+ * ns2ui - Nanoseconds to UI time periods
+ */
+static inline unsigned int ns2ui(struct dw_mipi_dsi *dsi, int ns)
+{
+	return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000);
+}
+
 static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 {
 	int ret, testdin, vco, val;
@@ -434,10 +450,21 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 					 SETRD_MAX | POWER_MANAGE |
 					 TER_RESISTORS_ON);
 
-
-	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
-	dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
-	dw_mipi_dsi_phy_write(dsi, 0x72, THS_ZERO_PROGRAM_EN | 0xa);
+	dw_mipi_dsi_phy_write(dsi, 0x60, TLP_PROGRAM_EN | ns2bc(dsi, 500));
+	dw_mipi_dsi_phy_write(dsi, 0x61, THS_PRE_PROGRAM_EN | ns2ui(dsi, 40));
+	dw_mipi_dsi_phy_write(dsi, 0x62, THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300));
+	dw_mipi_dsi_phy_write(dsi, 0x63, THS_PRE_PROGRAM_EN | ns2ui(dsi, 100));
+	dw_mipi_dsi_phy_write(dsi, 0x64, BIT(5) | ns2bc(dsi, 100));
+	dw_mipi_dsi_phy_write(dsi, 0x65, BIT(5) | (ns2bc(dsi, 60) + 7));
+
+	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | ns2bc(dsi, 500));
+	dw_mipi_dsi_phy_write(dsi, 0x71,
+			      THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 5));
+	dw_mipi_dsi_phy_write(dsi, 0x72,
+			      THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2));
+	dw_mipi_dsi_phy_write(dsi, 0x73,
+			      THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8));
+	dw_mipi_dsi_phy_write(dsi, 0x74, BIT(5) | ns2bc(dsi, 100));
 
 	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
 				     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 16/23] drm/rockchip: dw-mipi-dsi: properly configure PHY timing

[John Keeping]

These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.

Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Simplify ns2bc and ns2ui calculations as suggested by Sean Paul
v3:
- Wrap some long lines
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 35 ++++++++++++++++++++++++++++++----
 1 file changed, 31 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 4fee5176c606..9b6a60deb69e 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -383,6 +383,22 @@ static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code,
 	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
 }
 
+/**
+ * ns2bc - Nanoseconds to byte clock cycles
+ */
+static inline unsigned int ns2bc(struct dw_mipi_dsi *dsi, int ns)
+{
+	return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000);
+}
+
+/**
+ * ns2ui - Nanoseconds to UI time periods
+ */
+static inline unsigned int ns2ui(struct dw_mipi_dsi *dsi, int ns)
+{
+	return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000);
+}
+
 static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 {
 	int ret, testdin, vco, val;
@@ -434,10 +450,21 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 					 SETRD_MAX | POWER_MANAGE |
 					 TER_RESISTORS_ON);
 
-
-	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
-	dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
-	dw_mipi_dsi_phy_write(dsi, 0x72, THS_ZERO_PROGRAM_EN | 0xa);
+	dw_mipi_dsi_phy_write(dsi, 0x60, TLP_PROGRAM_EN | ns2bc(dsi, 500));
+	dw_mipi_dsi_phy_write(dsi, 0x61, THS_PRE_PROGRAM_EN | ns2ui(dsi, 40));
+	dw_mipi_dsi_phy_write(dsi, 0x62, THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300));
+	dw_mipi_dsi_phy_write(dsi, 0x63, THS_PRE_PROGRAM_EN | ns2ui(dsi, 100));
+	dw_mipi_dsi_phy_write(dsi, 0x64, BIT(5) | ns2bc(dsi, 100));
+	dw_mipi_dsi_phy_write(dsi, 0x65, BIT(5) | (ns2bc(dsi, 60) + 7));
+
+	dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | ns2bc(dsi, 500));
+	dw_mipi_dsi_phy_write(dsi, 0x71,
+			      THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 5));
+	dw_mipi_dsi_phy_write(dsi, 0x72,
+			      THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2));
+	dw_mipi_dsi_phy_write(dsi, 0x73,
+			      THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8));
+	dw_mipi_dsi_phy_write(dsi, 0x74, BIT(5) | ns2bc(dsi, 100));
 
 	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
 				     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 17/23] drm/rockchip: dw-mipi-dsi: improve PLL configuration

[John Keeping]

The multiplication ratio for the PLL is required to be even due to the
use of a "by 2 pre-scaler".  Currently we are likely to end up with an
odd multiplier even though there is an equivalent set of parameters with
an even multiplier.

For example, using the 324MHz bit rate with a reference clock of 24MHz
we end up with M = 27, N = 2 whereas the example in the PHY databook
gives M = 54, N = 4 for this bit rate and reference clock.

By walking down through the available multiplier instead of up we are
more likely to hit an even multiplier.  With the above example we do now
get M = 54, N = 4 as given by the databook.

While doing this, change the loop limits to encode the actual limits on
the divisor, which are:

	40MHz >= (pllref / N) >= 5MHz

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add a comment explaining the limits so that it can be understood
  without finding the commit message above
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 9b6a60deb69e..e6b52c7cb5e3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -518,7 +518,18 @@ static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi,
 	pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC);
 	tmp = pllref;
 
-	for (i = 1; i < 6; i++) {
+	/*
+	 * The limits on the PLL divisor are:
+	 *
+	 *	5MHz <= (pllref / n) <= 40MHz
+	 *
+	 * we walk over these values in descreasing order so that if we hit
+	 * an exact match for target_mbps it is more likely that "m" will be
+	 * even.
+	 *
+	 * TODO: ensure that "m" is even after this loop.
+	 */
+	for (i = pllref / 5; i > (pllref / 40); i--) {
 		pre = pllref / i;
 		if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) {
 			tmp = target_mbps % pre;
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 17/23] drm/rockchip: dw-mipi-dsi: improve PLL configuration

[John Keeping]

The multiplication ratio for the PLL is required to be even due to the
use of a "by 2 pre-scaler".  Currently we are likely to end up with an
odd multiplier even though there is an equivalent set of parameters with
an even multiplier.

For example, using the 324MHz bit rate with a reference clock of 24MHz
we end up with M = 27, N = 2 whereas the example in the PHY databook
gives M = 54, N = 4 for this bit rate and reference clock.

By walking down through the available multiplier instead of up we are
more likely to hit an even multiplier.  With the above example we do now
get M = 54, N = 4 as given by the databook.

While doing this, change the loop limits to encode the actual limits on
the divisor, which are:

	40MHz >= (pllref / N) >= 5MHz

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add a comment explaining the limits so that it can be understood
  without finding the commit message above
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 9b6a60deb69e..e6b52c7cb5e3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -518,7 +518,18 @@ static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi,
 	pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC);
 	tmp = pllref;
 
-	for (i = 1; i < 6; i++) {
+	/*
+	 * The limits on the PLL divisor are:
+	 *
+	 *	5MHz <= (pllref / n) <= 40MHz
+	 *
+	 * we walk over these values in descreasing order so that if we hit
+	 * an exact match for target_mbps it is more likely that "m" will be
+	 * even.
+	 *
+	 * TODO: ensure that "m" is even after this loop.
+	 */
+	for (i = pllref / 5; i > (pllref / 40); i--) {
 		pre = pllref / i;
 		if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) {
 			tmp = target_mbps % pre;
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 17/23] drm/rockchip: dw-mipi-dsi: improve PLL configuration

[John Keeping]

The multiplication ratio for the PLL is required to be even due to the
use of a "by 2 pre-scaler".  Currently we are likely to end up with an
odd multiplier even though there is an equivalent set of parameters with
an even multiplier.

For example, using the 324MHz bit rate with a reference clock of 24MHz
we end up with M = 27, N = 2 whereas the example in the PHY databook
gives M = 54, N = 4 for this bit rate and reference clock.

By walking down through the available multiplier instead of up we are
more likely to hit an even multiplier.  With the above example we do now
get M = 54, N = 4 as given by the databook.

While doing this, change the loop limits to encode the actual limits on
the divisor, which are:

	40MHz >= (pllref / N) >= 5MHz

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add a comment explaining the limits so that it can be understood
  without finding the commit message above
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 9b6a60deb69e..e6b52c7cb5e3 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -518,7 +518,18 @@ static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi,
 	pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC);
 	tmp = pllref;
 
-	for (i = 1; i < 6; i++) {
+	/*
+	 * The limits on the PLL divisor are:
+	 *
+	 *	5MHz <= (pllref / n) <= 40MHz
+	 *
+	 * we walk over these values in descreasing order so that if we hit
+	 * an exact match for target_mbps it is more likely that "m" will be
+	 * even.
+	 *
+	 * TODO: ensure that "m" is even after this loop.
+	 */
+	for (i = pllref / 5; i > (pllref / 40); i--) {
 		pre = pllref / i;
 		if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) {
 			tmp = target_mbps % pre;
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 18/23] drm/rockchip: dw-mipi-dsi: use specific poll helper

[John Keeping]

As the documentation for readx_poll_timeout says, we want to use the
specialized macro for readl rather than using the generic version
directly.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index e6b52c7cb5e3..ccf818d5c7ac 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -470,14 +470,14 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 				     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
 
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
 				 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
 	if (ret < 0) {
 		dev_err(dsi->dev, "failed to wait for phy lock state\n");
 		return ret;
 	}
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
 				 val, val & STOP_STATE_CLK_LANE, 1000,
 				 PHY_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -604,7 +604,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 	int ret;
 	u32 val, mask;
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
 				 CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -615,7 +615,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
 	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
-	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 				 val, (val & mask) == mask,
 				 1000, CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -676,7 +676,7 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 			len -= pld_data_bytes;
 		}
 
-		ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 					 val, !(val & GEN_PLD_W_FULL), 1000,
 					 CMD_PKT_STATUS_TIMEOUT_US);
 		if (ret < 0) {
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 18/23] drm/rockchip: dw-mipi-dsi: use specific poll helper

[John Keeping]

As the documentation for readx_poll_timeout says, we want to use the
specialized macro for readl rather than using the generic version
directly.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index e6b52c7cb5e3..ccf818d5c7ac 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -470,14 +470,14 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 				     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
 
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
 				 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
 	if (ret < 0) {
 		dev_err(dsi->dev, "failed to wait for phy lock state\n");
 		return ret;
 	}
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
 				 val, val & STOP_STATE_CLK_LANE, 1000,
 				 PHY_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -604,7 +604,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 	int ret;
 	u32 val, mask;
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
 				 CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -615,7 +615,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
 	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
-	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 				 val, (val & mask) == mask,
 				 1000, CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -676,7 +676,7 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 			len -= pld_data_bytes;
 		}
 
-		ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 					 val, !(val & GEN_PLD_W_FULL), 1000,
 					 CMD_PKT_STATUS_TIMEOUT_US);
 		if (ret < 0) {
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 18/23] drm/rockchip: dw-mipi-dsi: use specific poll helper

[John Keeping]

As the documentation for readx_poll_timeout says, we want to use the
specialized macro for readl rather than using the generic version
directly.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index e6b52c7cb5e3..ccf818d5c7ac 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -470,14 +470,14 @@ static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
 				     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
 
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
 				 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
 	if (ret < 0) {
 		dev_err(dsi->dev, "failed to wait for phy lock state\n");
 		return ret;
 	}
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
 				 val, val & STOP_STATE_CLK_LANE, 1000,
 				 PHY_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -604,7 +604,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 	int ret;
 	u32 val, mask;
 
-	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 				 val, !(val & GEN_CMD_FULL), 1000,
 				 CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -615,7 +615,7 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
 	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
 
 	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
-	ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 				 val, (val & mask) == mask,
 				 1000, CMD_PKT_STATUS_TIMEOUT_US);
 	if (ret < 0) {
@@ -676,7 +676,7 @@ static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
 			len -= pld_data_bytes;
 		}
 
-		ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
 					 val, !(val & GEN_PLD_W_FULL), 1000,
 					 CMD_PKT_STATUS_TIMEOUT_US);
 		if (ret < 0) {
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 19/23] drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC

[John Keeping]

This matches other drivers.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index ccf818d5c7ac..60dfb5666a25 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -791,9 +791,9 @@ static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
 		break;
 	}
 
-	if (!(mode->flags & DRM_MODE_FLAG_PVSYNC))
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
 		val |= VSYNC_ACTIVE_LOW;
-	if (!(mode->flags & DRM_MODE_FLAG_PHSYNC))
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
 		val |= HSYNC_ACTIVE_LOW;
 
 	dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 19/23] drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC

[John Keeping]

This matches other drivers.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index ccf818d5c7ac..60dfb5666a25 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -791,9 +791,9 @@ static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
 		break;
 	}
 
-	if (!(mode->flags & DRM_MODE_FLAG_PVSYNC))
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
 		val |= VSYNC_ACTIVE_LOW;
-	if (!(mode->flags & DRM_MODE_FLAG_PHSYNC))
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
 		val |= HSYNC_ACTIVE_LOW;
 
 	dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 19/23] drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC

[John Keeping]

This matches other drivers.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index ccf818d5c7ac..60dfb5666a25 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -791,9 +791,9 @@ static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
 		break;
 	}
 
-	if (!(mode->flags & DRM_MODE_FLAG_PVSYNC))
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
 		val |= VSYNC_ACTIVE_LOW;
-	if (!(mode->flags & DRM_MODE_FLAG_PHSYNC))
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
 		val |= HSYNC_ACTIVE_LOW;
 
 	dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 20/23] drm/rockchip: vop: test for P{H,V}SYNC

[John Keeping]

When connected to the MIPI DSI output, we need to use N{H,V}SYNC for the
internal connection but these flags are meaningless for DSI panels.
Switch the test so that we do not set the P{H,V}SYNC bits unless the
mode requires it.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Mark's Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index c7eba305c488..67aefc6d4e9a 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -933,8 +933,8 @@ static void vop_crtc_enable(struct drm_crtc *crtc)
 	}
 
 	pin_pol = 0x8;
-	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC) ? 0 : 1;
-	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC) ? 0 : (1 << 1);
+	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PHSYNC) ? 1 : 0;
+	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? (1 << 1) : 0;
 	VOP_CTRL_SET(vop, pin_pol, pin_pol);
 
 	switch (s->output_type) {
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 20/23] drm/rockchip: vop: test for P{H,V}SYNC

[John Keeping]

When connected to the MIPI DSI output, we need to use N{H,V}SYNC for the
internal connection but these flags are meaningless for DSI panels.
Switch the test so that we do not set the P{H,V}SYNC bits unless the
mode requires it.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Mark's Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index c7eba305c488..67aefc6d4e9a 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -933,8 +933,8 @@ static void vop_crtc_enable(struct drm_crtc *crtc)
 	}
 
 	pin_pol = 0x8;
-	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC) ? 0 : 1;
-	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC) ? 0 : (1 << 1);
+	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PHSYNC) ? 1 : 0;
+	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? (1 << 1) : 0;
 	VOP_CTRL_SET(vop, pin_pol, pin_pol);
 
 	switch (s->output_type) {
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 20/23] drm/rockchip: vop: test for P{H,V}SYNC

[John Keeping]

When connected to the MIPI DSI output, we need to use N{H,V}SYNC for the
internal connection but these flags are meaningless for DSI panels.
Switch the test so that we do not set the P{H,V}SYNC bits unless the
mode requires it.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Mark's Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index c7eba305c488..67aefc6d4e9a 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -933,8 +933,8 @@ static void vop_crtc_enable(struct drm_crtc *crtc)
 	}
 
 	pin_pol = 0x8;
-	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC) ? 0 : 1;
-	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC) ? 0 : (1 << 1);
+	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PHSYNC) ? 1 : 0;
+	pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? (1 << 1) : 0;
 	VOP_CTRL_SET(vop, pin_pol, pin_pol);
 
 	switch (s->output_type) {
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 21/23] drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded

[John Keeping]

This ensures that the output resolution is known before fbcon loads.
mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to
simplify error cleanup since the order of these operations does not
matter.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Use "return 0" to separate normal code flow from error cleanup
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 60dfb5666a25..9edb868f8dc1 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -1189,12 +1189,27 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 		goto err_pllref;
 	}
 
-	dev_set_drvdata(dev, dsi);
-
 	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
 	dsi->dsi_host.dev = dev;
-	return mipi_dsi_host_register(&dsi->dsi_host);
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
+		goto err_cleanup;
+	}
+
+	if (!dsi->panel) {
+		ret = -EPROBE_DEFER;
+		goto err_mipi_dsi_host;
+	}
 
+	dev_set_drvdata(dev, dsi);
+	return 0;
+
+err_mipi_dsi_host:
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+err_cleanup:
+	drm_encoder_cleanup(&dsi->encoder);
+	drm_connector_cleanup(&dsi->connector);
 err_pllref:
 	clk_disable_unprepare(dsi->pllref_clk);
 	return ret;
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 21/23] drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded

[John Keeping]

This ensures that the output resolution is known before fbcon loads.
mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to
simplify error cleanup since the order of these operations does not
matter.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Use "return 0" to separate normal code flow from error cleanup
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 60dfb5666a25..9edb868f8dc1 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -1189,12 +1189,27 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 		goto err_pllref;
 	}
 
-	dev_set_drvdata(dev, dsi);
-
 	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
 	dsi->dsi_host.dev = dev;
-	return mipi_dsi_host_register(&dsi->dsi_host);
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
+		goto err_cleanup;
+	}
+
+	if (!dsi->panel) {
+		ret = -EPROBE_DEFER;
+		goto err_mipi_dsi_host;
+	}
 
+	dev_set_drvdata(dev, dsi);
+	return 0;
+
+err_mipi_dsi_host:
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+err_cleanup:
+	drm_encoder_cleanup(&dsi->encoder);
+	drm_connector_cleanup(&dsi->connector);
 err_pllref:
 	clk_disable_unprepare(dsi->pllref_clk);
 	return ret;
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 21/23] drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded

[John Keeping]

This ensures that the output resolution is known before fbcon loads.
mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to
simplify error cleanup since the order of these operations does not
matter.

Signed-off-by: John Keeping <john@metanate.com>
---
v4:
- Use "return 0" to separate normal code flow from error cleanup
Unchanged in v3
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 60dfb5666a25..9edb868f8dc1 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -1189,12 +1189,27 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 		goto err_pllref;
 	}
 
-	dev_set_drvdata(dev, dsi);
-
 	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
 	dsi->dsi_host.dev = dev;
-	return mipi_dsi_host_register(&dsi->dsi_host);
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
+		goto err_cleanup;
+	}
+
+	if (!dsi->panel) {
+		ret = -EPROBE_DEFER;
+		goto err_mipi_dsi_host;
+	}
 
+	dev_set_drvdata(dev, dsi);
+	return 0;
+
+err_mipi_dsi_host:
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+err_cleanup:
+	drm_encoder_cleanup(&dsi->encoder);
+	drm_connector_cleanup(&dsi->connector);
 err_pllref:
 	clk_disable_unprepare(dsi->pllref_clk);
 	return ret;
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 22/23] drm/rockchip: dw-mipi-dsi: support non-burst modes

[John Keeping]

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 21 +++++++++++++--------
 1 file changed, 13 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 9edb868f8dc1..0c4bae711e84 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -82,7 +82,9 @@
 #define FRAME_BTA_ACK			BIT(14)
 #define ENABLE_LOW_POWER		(0x3f << 8)
 #define ENABLE_LOW_POWER_MASK		(0x3f << 8)
-#define VID_MODE_TYPE_BURST_SYNC_PULSES		0x2
+#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
+#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
+#define VID_MODE_TYPE_BURST			0x2
 #define VID_MODE_TYPE_MASK			0x3
 
 #define DSI_VID_PKT_SIZE		0x3c
@@ -286,6 +288,7 @@ struct dw_mipi_dsi {
 	u32 format;
 	u16 input_div;
 	u16 feedback_div;
+	unsigned long mode_flags;
 
 	const struct dw_mipi_dsi_plat_data *pdata;
 };
@@ -558,15 +561,10 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
 		return -EINVAL;
 	}
 
-	if (!(device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) ||
-	    !(device->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)) {
-		dev_err(dsi->dev, "device mode is unsupported\n");
-		return -EINVAL;
-	}
-
 	dsi->lanes = device->lanes;
 	dsi->channel = device->channel;
 	dsi->format = device->format;
+	dsi->mode_flags = device->mode_flags;
 	dsi->panel = of_drm_find_panel(device->dev.of_node);
 	if (dsi->panel)
 		return drm_panel_attach(dsi->panel, &dsi->connector);
@@ -725,7 +723,14 @@ static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
 {
 	u32 val;
 
-	val = VID_MODE_TYPE_BURST_SYNC_PULSES | ENABLE_LOW_POWER;
+	val = ENABLE_LOW_POWER;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		val |= VID_MODE_TYPE_BURST;
+	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
+	else
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
 
 	dsi_write(dsi, DSI_VID_MODE_CFG, val);
 }
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 22/23] drm/rockchip: dw-mipi-dsi: support non-burst modes

[John Keeping]

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 21 +++++++++++++--------
 1 file changed, 13 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 9edb868f8dc1..0c4bae711e84 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -82,7 +82,9 @@
 #define FRAME_BTA_ACK			BIT(14)
 #define ENABLE_LOW_POWER		(0x3f << 8)
 #define ENABLE_LOW_POWER_MASK		(0x3f << 8)
-#define VID_MODE_TYPE_BURST_SYNC_PULSES		0x2
+#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
+#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
+#define VID_MODE_TYPE_BURST			0x2
 #define VID_MODE_TYPE_MASK			0x3
 
 #define DSI_VID_PKT_SIZE		0x3c
@@ -286,6 +288,7 @@ struct dw_mipi_dsi {
 	u32 format;
 	u16 input_div;
 	u16 feedback_div;
+	unsigned long mode_flags;
 
 	const struct dw_mipi_dsi_plat_data *pdata;
 };
@@ -558,15 +561,10 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
 		return -EINVAL;
 	}
 
-	if (!(device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) ||
-	    !(device->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)) {
-		dev_err(dsi->dev, "device mode is unsupported\n");
-		return -EINVAL;
-	}
-
 	dsi->lanes = device->lanes;
 	dsi->channel = device->channel;
 	dsi->format = device->format;
+	dsi->mode_flags = device->mode_flags;
 	dsi->panel = of_drm_find_panel(device->dev.of_node);
 	if (dsi->panel)
 		return drm_panel_attach(dsi->panel, &dsi->connector);
@@ -725,7 +723,14 @@ static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
 {
 	u32 val;
 
-	val = VID_MODE_TYPE_BURST_SYNC_PULSES | ENABLE_LOW_POWER;
+	val = ENABLE_LOW_POWER;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		val |= VID_MODE_TYPE_BURST;
+	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
+	else
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
 
 	dsi_write(dsi, DSI_VID_MODE_CFG, val);
 }
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 22/23] drm/rockchip: dw-mipi-dsi: support non-burst modes

[John Keeping]

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
v4:
- Add Sean's Reviewed-by
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 21 +++++++++++++--------
 1 file changed, 13 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 9edb868f8dc1..0c4bae711e84 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -82,7 +82,9 @@
 #define FRAME_BTA_ACK			BIT(14)
 #define ENABLE_LOW_POWER		(0x3f << 8)
 #define ENABLE_LOW_POWER_MASK		(0x3f << 8)
-#define VID_MODE_TYPE_BURST_SYNC_PULSES		0x2
+#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
+#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
+#define VID_MODE_TYPE_BURST			0x2
 #define VID_MODE_TYPE_MASK			0x3
 
 #define DSI_VID_PKT_SIZE		0x3c
@@ -286,6 +288,7 @@ struct dw_mipi_dsi {
 	u32 format;
 	u16 input_div;
 	u16 feedback_div;
+	unsigned long mode_flags;
 
 	const struct dw_mipi_dsi_plat_data *pdata;
 };
@@ -558,15 +561,10 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
 		return -EINVAL;
 	}
 
-	if (!(device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) ||
-	    !(device->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)) {
-		dev_err(dsi->dev, "device mode is unsupported\n");
-		return -EINVAL;
-	}
-
 	dsi->lanes = device->lanes;
 	dsi->channel = device->channel;
 	dsi->format = device->format;
+	dsi->mode_flags = device->mode_flags;
 	dsi->panel = of_drm_find_panel(device->dev.of_node);
 	if (dsi->panel)
 		return drm_panel_attach(dsi->panel, &dsi->connector);
@@ -725,7 +723,14 @@ static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
 {
 	u32 val;
 
-	val = VID_MODE_TYPE_BURST_SYNC_PULSES | ENABLE_LOW_POWER;
+	val = ENABLE_LOW_POWER;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		val |= VID_MODE_TYPE_BURST;
+	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
+	else
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
 
 	dsi_write(dsi, DSI_VID_MODE_CFG, val);
 }
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[John Keeping]

In order to fully reset the state of the MIPI controller we must assert
this reset.

This is slightly more complicated than it could be in order to maintain
compatibility with device trees that do not specify the reset property.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
---
v4:
- Fix error check for devm_reset_control_get() to use ENOENT
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0c4bae711e84..30da75667334 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/regmap.h>
+#include <linux/reset.h>
 #include <linux/mfd/syscon.h>
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc.h>
@@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 			of_match_device(dw_mipi_dsi_dt_ids, dev);
 	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
 	struct platform_device *pdev = to_platform_device(dev);
+	struct reset_control *apb_rst;
 	struct drm_device *drm = data;
 	struct dw_mipi_dsi *dsi;
 	struct resource *res;
@@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 		return ret;
 	}
 
+	/*
+	 * Note that the reset was not defined in the initial device tree, so
+	 * we have to be prepared for it not being found.
+	 */
+	apb_rst = devm_reset_control_get(dev, "apb");
+	if (IS_ERR(apb_rst)) {
+		ret = PTR_ERR(apb_rst);
+		if (ret == -ENOENT) {
+			apb_rst = NULL;
+		} else {
+			dev_err(dev, "Unable to get reset control: %d\n", ret);
+			return ret;
+		}
+	}
+
+	if (apb_rst) {
+		ret = clk_prepare_enable(dsi->pclk);
+		if (ret) {
+			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+			return ret;
+		}
+
+		reset_control_assert(apb_rst);
+		usleep_range(10, 20);
+		reset_control_deassert(apb_rst);
+
+		clk_disable_unprepare(dsi->pclk);
+	}
+
 	ret = clk_prepare_enable(dsi->pllref_clk);
 	if (ret) {
 		dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[John Keeping]

In order to fully reset the state of the MIPI controller we must assert
this reset.

This is slightly more complicated than it could be in order to maintain
compatibility with device trees that do not specify the reset property.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
---
v4:
- Fix error check for devm_reset_control_get() to use ENOENT
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0c4bae711e84..30da75667334 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/regmap.h>
+#include <linux/reset.h>
 #include <linux/mfd/syscon.h>
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc.h>
@@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 			of_match_device(dw_mipi_dsi_dt_ids, dev);
 	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
 	struct platform_device *pdev = to_platform_device(dev);
+	struct reset_control *apb_rst;
 	struct drm_device *drm = data;
 	struct dw_mipi_dsi *dsi;
 	struct resource *res;
@@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 		return ret;
 	}
 
+	/*
+	 * Note that the reset was not defined in the initial device tree, so
+	 * we have to be prepared for it not being found.
+	 */
+	apb_rst = devm_reset_control_get(dev, "apb");
+	if (IS_ERR(apb_rst)) {
+		ret = PTR_ERR(apb_rst);
+		if (ret == -ENOENT) {
+			apb_rst = NULL;
+		} else {
+			dev_err(dev, "Unable to get reset control: %d\n", ret);
+			return ret;
+		}
+	}
+
+	if (apb_rst) {
+		ret = clk_prepare_enable(dsi->pclk);
+		if (ret) {
+			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+			return ret;
+		}
+
+		reset_control_assert(apb_rst);
+		usleep_range(10, 20);
+		reset_control_deassert(apb_rst);
+
+		clk_disable_unprepare(dsi->pclk);
+	}
+
 	ret = clk_prepare_enable(dsi->pllref_clk);
 	if (ret) {
 		dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[John Keeping]

In order to fully reset the state of the MIPI controller we must assert
this reset.

This is slightly more complicated than it could be in order to maintain
compatibility with device trees that do not specify the reset property.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
---
v4:
- Fix error check for devm_reset_control_get() to use ENOENT
v3:
- Add Chris' Reviewed-by
Unchanged in v2
---
 drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 0c4bae711e84..30da75667334 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/regmap.h>
+#include <linux/reset.h>
 #include <linux/mfd/syscon.h>
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc.h>
@@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 			of_match_device(dw_mipi_dsi_dt_ids, dev);
 	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
 	struct platform_device *pdev = to_platform_device(dev);
+	struct reset_control *apb_rst;
 	struct drm_device *drm = data;
 	struct dw_mipi_dsi *dsi;
 	struct resource *res;
@@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
 		return ret;
 	}
 
+	/*
+	 * Note that the reset was not defined in the initial device tree, so
+	 * we have to be prepared for it not being found.
+	 */
+	apb_rst = devm_reset_control_get(dev, "apb");
+	if (IS_ERR(apb_rst)) {
+		ret = PTR_ERR(apb_rst);
+		if (ret == -ENOENT) {
+			apb_rst = NULL;
+		} else {
+			dev_err(dev, "Unable to get reset control: %d\n", ret);
+			return ret;
+		}
+	}
+
+	if (apb_rst) {
+		ret = clk_prepare_enable(dsi->pclk);
+		if (ret) {
+			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+			return ret;
+		}
+
+		reset_control_assert(apb_rst);
+		usleep_range(10, 20);
+		reset_control_deassert(apb_rst);
+
+		clk_disable_unprepare(dsi->pclk);
+	}
+
 	ret = clk_prepare_enable(dsi->pllref_clk);
 	if (ret) {
 		dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);
-- 
2.12.0.rc0.230.gf625d4cdb9.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[Brian Norris]

+ devicetree

Hi,

On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> In order to fully reset the state of the MIPI controller we must assert
> this reset.
> 
> This is slightly more complicated than it could be in order to maintain
> compatibility with device trees that do not specify the reset property.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> Reviewed-by: Chris Zhong <zyw@rock-chips.com>
> ---
> v4:
> - Fix error check for devm_reset_control_get() to use ENOENT
> v3:
> - Add Chris' Reviewed-by
> Unchanged in v2
> ---
>  drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 31 +++++++++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> index 0c4bae711e84..30da75667334 100644
> --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> @@ -13,6 +13,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <linux/mfd/syscon.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_crtc.h>
> @@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  			of_match_device(dw_mipi_dsi_dt_ids, dev);
>  	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
>  	struct platform_device *pdev = to_platform_device(dev);
> +	struct reset_control *apb_rst;
>  	struct drm_device *drm = data;
>  	struct dw_mipi_dsi *dsi;
>  	struct resource *res;
> @@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  		return ret;
>  	}
>  
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");

Did this reset ever get documented in the device tree bindings? I
couldn't find it. Perhaps a follow-up patch is in order?

[...]

Brian

[PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[Brian Norris]

+ devicetree

Hi,

On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> In order to fully reset the state of the MIPI controller we must assert
> this reset.
> 
> This is slightly more complicated than it could be in order to maintain
> compatibility with device trees that do not specify the reset property.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> Reviewed-by: Chris Zhong <zyw@rock-chips.com>
> ---
> v4:
> - Fix error check for devm_reset_control_get() to use ENOENT
> v3:
> - Add Chris' Reviewed-by
> Unchanged in v2
> ---
>  drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 31 +++++++++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> index 0c4bae711e84..30da75667334 100644
> --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> @@ -13,6 +13,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <linux/mfd/syscon.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_crtc.h>
> @@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  			of_match_device(dw_mipi_dsi_dt_ids, dev);
>  	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
>  	struct platform_device *pdev = to_platform_device(dev);
> +	struct reset_control *apb_rst;
>  	struct drm_device *drm = data;
>  	struct dw_mipi_dsi *dsi;
>  	struct resource *res;
> @@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  		return ret;
>  	}
>  
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");

Did this reset ever get documented in the device tree bindings? I
couldn't find it. Perhaps a follow-up patch is in order?

[...]

Brian

Re: [PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[Brian Norris]

+ devicetree

Hi,

On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> In order to fully reset the state of the MIPI controller we must assert
> this reset.
> 
> This is slightly more complicated than it could be in order to maintain
> compatibility with device trees that do not specify the reset property.
> 
> Signed-off-by: John Keeping <john-HooS5bfzL4hWk0Htik3J/w@public.gmane.org>
> Reviewed-by: Chris Zhong <zyw-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> ---
> v4:
> - Fix error check for devm_reset_control_get() to use ENOENT
> v3:
> - Add Chris' Reviewed-by
> Unchanged in v2
> ---
>  drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 31 +++++++++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> index 0c4bae711e84..30da75667334 100644
> --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> @@ -13,6 +13,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <linux/mfd/syscon.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_crtc.h>
> @@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  			of_match_device(dw_mipi_dsi_dt_ids, dev);
>  	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
>  	struct platform_device *pdev = to_platform_device(dev);
> +	struct reset_control *apb_rst;
>  	struct drm_device *drm = data;
>  	struct dw_mipi_dsi *dsi;
>  	struct resource *res;
> @@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  		return ret;
>  	}
>  
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");

Did this reset ever get documented in the device tree bindings? I
couldn't find it. Perhaps a follow-up patch is in order?

[...]

Brian

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[John Keeping]

This reset is required in order to fully reset the internal state of the
MIPI controller.

Signed-off-by: John Keeping <john@metanate.com>
---
On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > +	/*
> > +	 * Note that the reset was not defined in the initial device tree, so
> > +	 * we have to be prepared for it not being found.
> > +	 */
> > +	apb_rst = devm_reset_control_get(dev, "apb");  
> 
> Did this reset ever get documented in the device tree bindings? I
> couldn't find it. Perhaps a follow-up patch is in order?

Here's a patch to do that.

 .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
index 1753f0cc6fad..28d0b437d3cd 100644
--- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
+++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
@@ -13,8 +13,13 @@ Required properties:
 - ports: contain a port node with endpoint definitions as defined in [2].
   For vopb,set the reg = <0> and set the reg = <1> for vopl.
 
+Optional properties:
+- resets: list of phandle + reset specifier pairs, as described in [3].
+- reset-names: string reset name, must be "apb".
+
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/media/video-interfaces.txt
+[3] Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 	mipi_dsi: mipi@ff960000 {
@@ -25,6 +30,8 @@ Example:
 		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
 		clock-names = "ref", "pclk";
+		resets = <&cru SRST_MIPIDSI0>;
+		reset-names = "apb";
 		rockchip,grf = <&grf>;
 		status = "okay";
 
-- 
2.12.0.rc2.230.ga28edc07cd.dirty

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[John Keeping]

This reset is required in order to fully reset the internal state of the
MIPI controller.

Signed-off-by: John Keeping <john@metanate.com>
---
On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > +	/*
> > +	 * Note that the reset was not defined in the initial device tree, so
> > +	 * we have to be prepared for it not being found.
> > +	 */
> > +	apb_rst = devm_reset_control_get(dev, "apb");  
> 
> Did this reset ever get documented in the device tree bindings? I
> couldn't find it. Perhaps a follow-up patch is in order?

Here's a patch to do that.

 .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
index 1753f0cc6fad..28d0b437d3cd 100644
--- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
+++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
@@ -13,8 +13,13 @@ Required properties:
 - ports: contain a port node with endpoint definitions as defined in [2].
   For vopb,set the reg = <0> and set the reg = <1> for vopl.
 
+Optional properties:
+- resets: list of phandle + reset specifier pairs, as described in [3].
+- reset-names: string reset name, must be "apb".
+
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/media/video-interfaces.txt
+[3] Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 	mipi_dsi: mipi at ff960000 {
@@ -25,6 +30,8 @@ Example:
 		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
 		clock-names = "ref", "pclk";
+		resets = <&cru SRST_MIPIDSI0>;
+		reset-names = "apb";
 		rockchip,grf = <&grf>;
 		status = "okay";
 
-- 
2.12.0.rc2.230.ga28edc07cd.dirty

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[John Keeping]

This reset is required in order to fully reset the internal state of the
MIPI controller.

Signed-off-by: John Keeping <john@metanate.com>
---
On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > +	/*
> > +	 * Note that the reset was not defined in the initial device tree, so
> > +	 * we have to be prepared for it not being found.
> > +	 */
> > +	apb_rst = devm_reset_control_get(dev, "apb");  
> 
> Did this reset ever get documented in the device tree bindings? I
> couldn't find it. Perhaps a follow-up patch is in order?

Here's a patch to do that.

 .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
index 1753f0cc6fad..28d0b437d3cd 100644
--- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
+++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
@@ -13,8 +13,13 @@ Required properties:
 - ports: contain a port node with endpoint definitions as defined in [2].
   For vopb,set the reg = <0> and set the reg = <1> for vopl.
 
+Optional properties:
+- resets: list of phandle + reset specifier pairs, as described in [3].
+- reset-names: string reset name, must be "apb".
+
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/media/video-interfaces.txt
+[3] Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 	mipi_dsi: mipi@ff960000 {
@@ -25,6 +30,8 @@ Example:
 		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
 		clock-names = "ref", "pclk";
+		resets = <&cru SRST_MIPIDSI0>;
+		reset-names = "apb";
 		rockchip,grf = <&grf>;
 		status = "okay";
 
-- 
2.12.0.rc2.230.ga28edc07cd.dirty

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Brian Norris]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.

FWIW:

Reviewed-by: Brian Norris <briannorris@chromium.org>

Thanks.

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Brian Norris]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.

FWIW:

Reviewed-by: Brian Norris <briannorris@chromium.org>

Thanks.

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Brian Norris]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john-HooS5bfzL4hWk0Htik3J/w@public.gmane.org>
> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.

FWIW:

Reviewed-by: Brian Norris <briannorris-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>

Thanks.

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Sean Paul]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>

I'm sorry I missed this in my review. Adding Rob Herring directly for his ack.

Also,

Reviewed-by: Sean Paul <seanpaul@chromium.org>

> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.
> 
>  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> index 1753f0cc6fad..28d0b437d3cd 100644
> --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> @@ -13,8 +13,13 @@ Required properties:
>  - ports: contain a port node with endpoint definitions as defined in [2].
>    For vopb,set the reg = <0> and set the reg = <1> for vopl.
>  
> +Optional properties:
> +- resets: list of phandle + reset specifier pairs, as described in [3].
> +- reset-names: string reset name, must be "apb".
> +
>  [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
>  [2] Documentation/devicetree/bindings/media/video-interfaces.txt
> +[3] Documentation/devicetree/bindings/reset/reset.txt
>  
>  Example:
>  	mipi_dsi: mipi@ff960000 {
> @@ -25,6 +30,8 @@ Example:
>  		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
>  		clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
>  		clock-names = "ref", "pclk";
> +		resets = <&cru SRST_MIPIDSI0>;
> +		reset-names = "apb";
>  		rockchip,grf = <&grf>;
>  		status = "okay";
>  
> -- 
> 2.12.0.rc2.230.ga28edc07cd.dirty
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Sean Paul]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>

I'm sorry I missed this in my review. Adding Rob Herring directly for his ack.

Also,

Reviewed-by: Sean Paul <seanpaul@chromium.org>

> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.
> 
>  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> index 1753f0cc6fad..28d0b437d3cd 100644
> --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> @@ -13,8 +13,13 @@ Required properties:
>  - ports: contain a port node with endpoint definitions as defined in [2].
>    For vopb,set the reg = <0> and set the reg = <1> for vopl.
>  
> +Optional properties:
> +- resets: list of phandle + reset specifier pairs, as described in [3].
> +- reset-names: string reset name, must be "apb".
> +
>  [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
>  [2] Documentation/devicetree/bindings/media/video-interfaces.txt
> +[3] Documentation/devicetree/bindings/reset/reset.txt
>  
>  Example:
>  	mipi_dsi: mipi at ff960000 {
> @@ -25,6 +30,8 @@ Example:
>  		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
>  		clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
>  		clock-names = "ref", "pclk";
> +		resets = <&cru SRST_MIPIDSI0>;
> +		reset-names = "apb";
>  		rockchip,grf = <&grf>;
>  		status = "okay";
>  
> -- 
> 2.12.0.rc2.230.ga28edc07cd.dirty
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Sean Paul]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>

I'm sorry I missed this in my review. Adding Rob Herring directly for his ack.

Also,

Reviewed-by: Sean Paul <seanpaul@chromium.org>

> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.
> 
>  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> index 1753f0cc6fad..28d0b437d3cd 100644
> --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
> @@ -13,8 +13,13 @@ Required properties:
>  - ports: contain a port node with endpoint definitions as defined in [2].
>    For vopb,set the reg = <0> and set the reg = <1> for vopl.
>  
> +Optional properties:
> +- resets: list of phandle + reset specifier pairs, as described in [3].
> +- reset-names: string reset name, must be "apb".
> +
>  [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
>  [2] Documentation/devicetree/bindings/media/video-interfaces.txt
> +[3] Documentation/devicetree/bindings/reset/reset.txt
>  
>  Example:
>  	mipi_dsi: mipi@ff960000 {
> @@ -25,6 +30,8 @@ Example:
>  		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
>  		clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
>  		clock-names = "ref", "pclk";
> +		resets = <&cru SRST_MIPIDSI0>;
> +		reset-names = "apb";
>  		rockchip,grf = <&grf>;
>  		status = "okay";
>  
> -- 
> 2.12.0.rc2.230.ga28edc07cd.dirty
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Rob Herring]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.
> 
>  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)

Acked-by: Rob Herring <robh@kernel.org>

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Rob Herring]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.
> 
>  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Rob Herring]

On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> This reset is required in order to fully reset the internal state of the
> MIPI controller.
> 
> Signed-off-by: John Keeping <john@metanate.com>
> ---
> On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:
> > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:
> > > +	/*
> > > +	 * Note that the reset was not defined in the initial device tree, so
> > > +	 * we have to be prepared for it not being found.
> > > +	 */
> > > +	apb_rst = devm_reset_control_get(dev, "apb");  
> > 
> > Did this reset ever get documented in the device tree bindings? I
> > couldn't find it. Perhaps a follow-up patch is in order?
> 
> Here's a patch to do that.
> 
>  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)

Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[John Keeping]

Hi Sean,

On Sun, 12 Mar 2017 07:06:59 -0500, Rob Herring wrote:

> On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> > This reset is required in order to fully reset the internal state of the
> > MIPI controller.
> > 
> > Signed-off-by: John Keeping <john@metanate.com>
> > ---
> > On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:  
> > > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:  
> > > > +	/*
> > > > +	 * Note that the reset was not defined in the initial device tree, so
> > > > +	 * we have to be prepared for it not being found.
> > > > +	 */
> > > > +	apb_rst = devm_reset_control_get(dev, "apb");    
> > > 
> > > Did this reset ever get documented in the device tree bindings? I
> > > couldn't find it. Perhaps a follow-up patch is in order?  
> > 
> > Here's a patch to do that.
> > 
> >  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
> >  1 file changed, 7 insertions(+)  
> 
> Acked-by: Rob Herring <robh@kernel.org>

I don't see this patch in linux-next, so I guess it has fallen through
the cracks somewhere.  Since we have Rob's ack, can you pick this via
drm-misc?


Regards,
John

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[John Keeping]

Hi Sean,

On Sun, 12 Mar 2017 07:06:59 -0500, Rob Herring wrote:

> On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> > This reset is required in order to fully reset the internal state of the
> > MIPI controller.
> > 
> > Signed-off-by: John Keeping <john@metanate.com>
> > ---
> > On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:  
> > > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:  
> > > > +	/*
> > > > +	 * Note that the reset was not defined in the initial device tree, so
> > > > +	 * we have to be prepared for it not being found.
> > > > +	 */
> > > > +	apb_rst = devm_reset_control_get(dev, "apb");    
> > > 
> > > Did this reset ever get documented in the device tree bindings? I
> > > couldn't find it. Perhaps a follow-up patch is in order?  
> > 
> > Here's a patch to do that.
> > 
> >  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
> >  1 file changed, 7 insertions(+)  
> 
> Acked-by: Rob Herring <robh@kernel.org>

I don't see this patch in linux-next, so I guess it has fallen through
the cracks somewhere.  Since we have Rob's ack, can you pick this via
drm-misc?


Regards,
John

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[John Keeping]

Hi Sean,

On Sun, 12 Mar 2017 07:06:59 -0500, Rob Herring wrote:

> On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> > This reset is required in order to fully reset the internal state of the
> > MIPI controller.
> > 
> > Signed-off-by: John Keeping <john-HooS5bfzL4hWk0Htik3J/w@public.gmane.org>
> > ---
> > On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:  
> > > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:  
> > > > +	/*
> > > > +	 * Note that the reset was not defined in the initial device tree, so
> > > > +	 * we have to be prepared for it not being found.
> > > > +	 */
> > > > +	apb_rst = devm_reset_control_get(dev, "apb");    
> > > 
> > > Did this reset ever get documented in the device tree bindings? I
> > > couldn't find it. Perhaps a follow-up patch is in order?  
> > 
> > Here's a patch to do that.
> > 
> >  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
> >  1 file changed, 7 insertions(+)  
> 
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

I don't see this patch in linux-next, so I guess it has fallen through
the cracks somewhere.  Since we have Rob's ack, can you pick this via
drm-misc?


Regards,
John
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Sean Paul]

On Tue, Apr 04, 2017 at 02:15:13PM +0100, John Keeping wrote:
> Hi Sean,
> 
> On Sun, 12 Mar 2017 07:06:59 -0500, Rob Herring wrote:
> 
> > On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> > > This reset is required in order to fully reset the internal state of the
> > > MIPI controller.
> > > 
> > > Signed-off-by: John Keeping <john@metanate.com>
> > > ---
> > > On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:  
> > > > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:  
> > > > > +	/*
> > > > > +	 * Note that the reset was not defined in the initial device tree, so
> > > > > +	 * we have to be prepared for it not being found.
> > > > > +	 */
> > > > > +	apb_rst = devm_reset_control_get(dev, "apb");    
> > > > 
> > > > Did this reset ever get documented in the device tree bindings? I
> > > > couldn't find it. Perhaps a follow-up patch is in order?  
> > > 
> > > Here's a patch to do that.
> > > 
> > >  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
> > >  1 file changed, 7 insertions(+)  
> > 
> > Acked-by: Rob Herring <robh@kernel.org>
> 
> I don't see this patch in linux-next, so I guess it has fallen through
> the cracks somewhere.  Since we have Rob's ack, can you pick this via
> drm-misc?
> 

Yeah, sorry about that. Applied to misc-next

Sean

> 
> Regards,
> John

-- 
Sean Paul, Software Engineer, Google / Chromium OS

[PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Sean Paul]

On Tue, Apr 04, 2017 at 02:15:13PM +0100, John Keeping wrote:
> Hi Sean,
> 
> On Sun, 12 Mar 2017 07:06:59 -0500, Rob Herring wrote:
> 
> > On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> > > This reset is required in order to fully reset the internal state of the
> > > MIPI controller.
> > > 
> > > Signed-off-by: John Keeping <john@metanate.com>
> > > ---
> > > On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:  
> > > > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:  
> > > > > +	/*
> > > > > +	 * Note that the reset was not defined in the initial device tree, so
> > > > > +	 * we have to be prepared for it not being found.
> > > > > +	 */
> > > > > +	apb_rst = devm_reset_control_get(dev, "apb");    
> > > > 
> > > > Did this reset ever get documented in the device tree bindings? I
> > > > couldn't find it. Perhaps a follow-up patch is in order?  
> > > 
> > > Here's a patch to do that.
> > > 
> > >  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
> > >  1 file changed, 7 insertions(+)  
> > 
> > Acked-by: Rob Herring <robh@kernel.org>
> 
> I don't see this patch in linux-next, so I guess it has fallen through
> the cracks somewhere.  Since we have Rob's ack, can you pick this via
> drm-misc?
> 

Yeah, sorry about that. Applied to misc-next

Sean

> 
> Regards,
> John

-- 
Sean Paul, Software Engineer, Google / Chromium OS

Re: [PATCH] dt-bindings: display: rk3288-mipi-dsi: add reset property

[Sean Paul]

On Tue, Apr 04, 2017 at 02:15:13PM +0100, John Keeping wrote:
> Hi Sean,
> 
> On Sun, 12 Mar 2017 07:06:59 -0500, Rob Herring wrote:
> 
> > On Fri, Mar 03, 2017 at 11:39:45AM +0000, John Keeping wrote:
> > > This reset is required in order to fully reset the internal state of the
> > > MIPI controller.
> > > 
> > > Signed-off-by: John Keeping <john-HooS5bfzL4hWk0Htik3J/w@public.gmane.org>
> > > ---
> > > On Thu, 2 Mar 2017 13:56:46 -0800, Brian Norris wrote:  
> > > > On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:  
> > > > > +	/*
> > > > > +	 * Note that the reset was not defined in the initial device tree, so
> > > > > +	 * we have to be prepared for it not being found.
> > > > > +	 */
> > > > > +	apb_rst = devm_reset_control_get(dev, "apb");    
> > > > 
> > > > Did this reset ever get documented in the device tree bindings? I
> > > > couldn't find it. Perhaps a follow-up patch is in order?  
> > > 
> > > Here's a patch to do that.
> > > 
> > >  .../devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt  | 7 +++++++
> > >  1 file changed, 7 insertions(+)  
> > 
> > Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> 
> I don't see this patch in linux-next, so I guess it has fallen through
> the cracks somewhere.  Since we have Rob's ack, can you pick this via
> drm-misc?
> 

Yeah, sorry about that. Applied to misc-next

Sean

> 
> Regards,
> John

-- 
Sean Paul, Software Engineer, Google / Chromium OS
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[Brian Norris]

Oh, one more thing:

On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:

> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> index 0c4bae711e84..30da75667334 100644
> --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> @@ -13,6 +13,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <linux/mfd/syscon.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_crtc.h>
> @@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  			of_match_device(dw_mipi_dsi_dt_ids, dev);
>  	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
>  	struct platform_device *pdev = to_platform_device(dev);
> +	struct reset_control *apb_rst;
>  	struct drm_device *drm = data;
>  	struct dw_mipi_dsi *dsi;
>  	struct resource *res;
> @@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  		return ret;
>  	}
>  
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");
> +	if (IS_ERR(apb_rst)) {
> +		ret = PTR_ERR(apb_rst);
> +		if (ret == -ENOENT) {
> +			apb_rst = NULL;
> +		} else {
> +			dev_err(dev, "Unable to get reset control: %d\n", ret);

Might want to check for -EPROBE_DEFER before printing an error?

Brian

> +			return ret;
> +		}
> +	}
> +
> +	if (apb_rst) {
> +		ret = clk_prepare_enable(dsi->pclk);
> +		if (ret) {
> +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> +			return ret;
> +		}
> +
> +		reset_control_assert(apb_rst);
> +		usleep_range(10, 20);
> +		reset_control_deassert(apb_rst);
> +
> +		clk_disable_unprepare(dsi->pclk);
> +	}
> +
>  	ret = clk_prepare_enable(dsi->pllref_clk);
>  	if (ret) {
>  		dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);

[PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[Brian Norris]

Oh, one more thing:

On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:

> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> index 0c4bae711e84..30da75667334 100644
> --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> @@ -13,6 +13,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <linux/mfd/syscon.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_crtc.h>
> @@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  			of_match_device(dw_mipi_dsi_dt_ids, dev);
>  	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
>  	struct platform_device *pdev = to_platform_device(dev);
> +	struct reset_control *apb_rst;
>  	struct drm_device *drm = data;
>  	struct dw_mipi_dsi *dsi;
>  	struct resource *res;
> @@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  		return ret;
>  	}
>  
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");
> +	if (IS_ERR(apb_rst)) {
> +		ret = PTR_ERR(apb_rst);
> +		if (ret == -ENOENT) {
> +			apb_rst = NULL;
> +		} else {
> +			dev_err(dev, "Unable to get reset control: %d\n", ret);

Might want to check for -EPROBE_DEFER before printing an error?

Brian

> +			return ret;
> +		}
> +	}
> +
> +	if (apb_rst) {
> +		ret = clk_prepare_enable(dsi->pclk);
> +		if (ret) {
> +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> +			return ret;
> +		}
> +
> +		reset_control_assert(apb_rst);
> +		usleep_range(10, 20);
> +		reset_control_deassert(apb_rst);
> +
> +		clk_disable_unprepare(dsi->pclk);
> +	}
> +
>  	ret = clk_prepare_enable(dsi->pllref_clk);
>  	if (ret) {
>  		dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);

Re: [PATCH v4 23/23] drm/rockchip: dw-mipi-dsi: add reset control

[Brian Norris]

Oh, one more thing:

On Fri, Feb 24, 2017 at 12:55:06PM +0000, John Keeping wrote:

> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> index 0c4bae711e84..30da75667334 100644
> --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> @@ -13,6 +13,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <linux/mfd/syscon.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_crtc.h>
> @@ -1144,6 +1145,7 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  			of_match_device(dw_mipi_dsi_dt_ids, dev);
>  	const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
>  	struct platform_device *pdev = to_platform_device(dev);
> +	struct reset_control *apb_rst;
>  	struct drm_device *drm = data;
>  	struct dw_mipi_dsi *dsi;
>  	struct resource *res;
> @@ -1182,6 +1184,35 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
>  		return ret;
>  	}
>  
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");
> +	if (IS_ERR(apb_rst)) {
> +		ret = PTR_ERR(apb_rst);
> +		if (ret == -ENOENT) {
> +			apb_rst = NULL;
> +		} else {
> +			dev_err(dev, "Unable to get reset control: %d\n", ret);

Might want to check for -EPROBE_DEFER before printing an error?

Brian

> +			return ret;
> +		}
> +	}
> +
> +	if (apb_rst) {
> +		ret = clk_prepare_enable(dsi->pclk);
> +		if (ret) {
> +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> +			return ret;
> +		}
> +
> +		reset_control_assert(apb_rst);
> +		usleep_range(10, 20);
> +		reset_control_deassert(apb_rst);
> +
> +		clk_disable_unprepare(dsi->pclk);
> +	}
> +
>  	ret = clk_prepare_enable(dsi->pllref_clk);
>  	if (ret) {
>  		dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);

Re: [PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Mark yao]

On 2017年02月24日 20:54, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
>
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
>
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
>
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.

Looks good to me.

Acked-by: Mark Yao <mark.yao@rock-chips.com>

>
> John Keeping (23):
>    drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>      MIPI
>    drm/rockchip: dw-mipi-dsi: pass mode in where needed
>    drm/rockchip: dw-mipi-dsi: remove mode_set hook
>    drm/rockchip: dw-mipi-dsi: fix command header writes
>    drm/rockchip: dw-mipi-dsi: fix generic packet status check
>    drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>    drm/rockchip: dw-mipi-dsi: include bad value in error message
>    drm/rockchip: dw-mipi-dsi: respect message flags
>    drm/rockchip: dw-mipi-dsi: only request HS clock when required
>    drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>    drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>    drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>    drm/rockchip: dw-mipi-dsi: fix escape clock rate
>    drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>    drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>    drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>    drm/rockchip: dw-mipi-dsi: improve PLL configuration
>    drm/rockchip: dw-mipi-dsi: use specific poll helper
>    drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>    drm/rockchip: vop: test for P{H,V}SYNC
>    drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>    drm/rockchip: dw-mipi-dsi: support non-burst modes
>    drm/rockchip: dw-mipi-dsi: add reset control
>
>   drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>   2 files changed, 220 insertions(+), 109 deletions(-)
>


-- 
Ｍark Yao

[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Mark yao]

On 2017?02?24? 20:54, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
>
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
>
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
>
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.

Looks good to me.

Acked-by: Mark Yao <mark.yao@rock-chips.com>

>
> John Keeping (23):
>    drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>      MIPI
>    drm/rockchip: dw-mipi-dsi: pass mode in where needed
>    drm/rockchip: dw-mipi-dsi: remove mode_set hook
>    drm/rockchip: dw-mipi-dsi: fix command header writes
>    drm/rockchip: dw-mipi-dsi: fix generic packet status check
>    drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>    drm/rockchip: dw-mipi-dsi: include bad value in error message
>    drm/rockchip: dw-mipi-dsi: respect message flags
>    drm/rockchip: dw-mipi-dsi: only request HS clock when required
>    drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>    drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>    drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>    drm/rockchip: dw-mipi-dsi: fix escape clock rate
>    drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>    drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>    drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>    drm/rockchip: dw-mipi-dsi: improve PLL configuration
>    drm/rockchip: dw-mipi-dsi: use specific poll helper
>    drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>    drm/rockchip: vop: test for P{H,V}SYNC
>    drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>    drm/rockchip: dw-mipi-dsi: support non-burst modes
>    drm/rockchip: dw-mipi-dsi: add reset control
>
>   drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>   2 files changed, 220 insertions(+), 109 deletions(-)
>


-- 
?ark Yao

Re: [PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Chris Zhong]

Hi John

I have test this v4 series on my RK3399 board, it works well, thanks.

Tested-by: Chris Zhong<zyw@rock-chips.com>


On 02/24/2017 08:54 PM, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
>
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
>
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
>
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.
>
> John Keeping (23):
>    drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>      MIPI
>    drm/rockchip: dw-mipi-dsi: pass mode in where needed
>    drm/rockchip: dw-mipi-dsi: remove mode_set hook
>    drm/rockchip: dw-mipi-dsi: fix command header writes
>    drm/rockchip: dw-mipi-dsi: fix generic packet status check
>    drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>    drm/rockchip: dw-mipi-dsi: include bad value in error message
>    drm/rockchip: dw-mipi-dsi: respect message flags
>    drm/rockchip: dw-mipi-dsi: only request HS clock when required
>    drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>    drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>    drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>    drm/rockchip: dw-mipi-dsi: fix escape clock rate
>    drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>    drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>    drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>    drm/rockchip: dw-mipi-dsi: improve PLL configuration
>    drm/rockchip: dw-mipi-dsi: use specific poll helper
>    drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>    drm/rockchip: vop: test for P{H,V}SYNC
>    drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>    drm/rockchip: dw-mipi-dsi: support non-burst modes
>    drm/rockchip: dw-mipi-dsi: add reset control
>
>   drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>   2 files changed, 220 insertions(+), 109 deletions(-)
>

-- 
Chris Zhong

[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Chris Zhong]

Hi John

I have test this v4 series on my RK3399 board, it works well, thanks.

Tested-by: Chris Zhong<zyw@rock-chips.com>


On 02/24/2017 08:54 PM, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
>
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
>
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
>
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.
>
> John Keeping (23):
>    drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>      MIPI
>    drm/rockchip: dw-mipi-dsi: pass mode in where needed
>    drm/rockchip: dw-mipi-dsi: remove mode_set hook
>    drm/rockchip: dw-mipi-dsi: fix command header writes
>    drm/rockchip: dw-mipi-dsi: fix generic packet status check
>    drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>    drm/rockchip: dw-mipi-dsi: include bad value in error message
>    drm/rockchip: dw-mipi-dsi: respect message flags
>    drm/rockchip: dw-mipi-dsi: only request HS clock when required
>    drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>    drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>    drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>    drm/rockchip: dw-mipi-dsi: fix escape clock rate
>    drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>    drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>    drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>    drm/rockchip: dw-mipi-dsi: improve PLL configuration
>    drm/rockchip: dw-mipi-dsi: use specific poll helper
>    drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>    drm/rockchip: vop: test for P{H,V}SYNC
>    drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>    drm/rockchip: dw-mipi-dsi: support non-burst modes
>    drm/rockchip: dw-mipi-dsi: add reset control
>
>   drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>   2 files changed, 220 insertions(+), 109 deletions(-)
>

-- 
Chris Zhong

Re: [PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Chris Zhong]

Hi John

I have test this v4 series on my RK3399 board, it works well, thanks.

Tested-by: Chris Zhong<zyw@rock-chips.com>


On 02/24/2017 08:54 PM, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
>
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
>
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
>
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.
>
> John Keeping (23):
>    drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>      MIPI
>    drm/rockchip: dw-mipi-dsi: pass mode in where needed
>    drm/rockchip: dw-mipi-dsi: remove mode_set hook
>    drm/rockchip: dw-mipi-dsi: fix command header writes
>    drm/rockchip: dw-mipi-dsi: fix generic packet status check
>    drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>    drm/rockchip: dw-mipi-dsi: include bad value in error message
>    drm/rockchip: dw-mipi-dsi: respect message flags
>    drm/rockchip: dw-mipi-dsi: only request HS clock when required
>    drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>    drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>    drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>    drm/rockchip: dw-mipi-dsi: fix escape clock rate
>    drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>    drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>    drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>    drm/rockchip: dw-mipi-dsi: improve PLL configuration
>    drm/rockchip: dw-mipi-dsi: use specific poll helper
>    drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>    drm/rockchip: vop: test for P{H,V}SYNC
>    drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>    drm/rockchip: dw-mipi-dsi: support non-burst modes
>    drm/rockchip: dw-mipi-dsi: add reset control
>
>   drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>   2 files changed, 220 insertions(+), 109 deletions(-)
>

-- 
Chris Zhong

Re: [PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Sean Paul]

On Fri, Feb 24, 2017 at 12:54:43PM +0000, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
> 
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
> 
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
> 
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.
> 
> John Keeping (23):
>   drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>     MIPI
>   drm/rockchip: dw-mipi-dsi: pass mode in where needed
>   drm/rockchip: dw-mipi-dsi: remove mode_set hook
>   drm/rockchip: dw-mipi-dsi: fix command header writes
>   drm/rockchip: dw-mipi-dsi: fix generic packet status check
>   drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>   drm/rockchip: dw-mipi-dsi: include bad value in error message
>   drm/rockchip: dw-mipi-dsi: respect message flags
>   drm/rockchip: dw-mipi-dsi: only request HS clock when required
>   drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>   drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>   drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>   drm/rockchip: dw-mipi-dsi: fix escape clock rate
>   drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>   drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>   drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>   drm/rockchip: dw-mipi-dsi: improve PLL configuration
>   drm/rockchip: dw-mipi-dsi: use specific poll helper
>   drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>   drm/rockchip: vop: test for P{H,V}SYNC
>   drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>   drm/rockchip: dw-mipi-dsi: support non-burst modes
>   drm/rockchip: dw-mipi-dsi: add reset control
> 
>  drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>  drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>  2 files changed, 220 insertions(+), 109 deletions(-)

Applied to drm-misc

Thanks,

Sean
> 
> -- 
> 2.12.0.rc0.230.gf625d4cdb9.dirty

[PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Sean Paul]

On Fri, Feb 24, 2017 at 12:54:43PM +0000, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
> 
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
> 
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
> 
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.
> 
> John Keeping (23):
>   drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>     MIPI
>   drm/rockchip: dw-mipi-dsi: pass mode in where needed
>   drm/rockchip: dw-mipi-dsi: remove mode_set hook
>   drm/rockchip: dw-mipi-dsi: fix command header writes
>   drm/rockchip: dw-mipi-dsi: fix generic packet status check
>   drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>   drm/rockchip: dw-mipi-dsi: include bad value in error message
>   drm/rockchip: dw-mipi-dsi: respect message flags
>   drm/rockchip: dw-mipi-dsi: only request HS clock when required
>   drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>   drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>   drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>   drm/rockchip: dw-mipi-dsi: fix escape clock rate
>   drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>   drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>   drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>   drm/rockchip: dw-mipi-dsi: improve PLL configuration
>   drm/rockchip: dw-mipi-dsi: use specific poll helper
>   drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>   drm/rockchip: vop: test for P{H,V}SYNC
>   drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>   drm/rockchip: dw-mipi-dsi: support non-burst modes
>   drm/rockchip: dw-mipi-dsi: add reset control
> 
>  drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>  drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>  2 files changed, 220 insertions(+), 109 deletions(-)

Applied to drm-misc

Thanks,

Sean
> 
> -- 
> 2.12.0.rc0.230.gf625d4cdb9.dirty

Re: [PATCH v4 00/23] drm/rockchip: MIPI fixes & improvements

[Sean Paul]

On Fri, Feb 24, 2017 at 12:54:43PM +0000, John Keeping wrote:
> This version is mostly small changes in response to review comments from
> Sean and Chris, the details are in the individual patches.
> 
> I decided to drop the final patch which adds support for MIPI read
> commands because I'm not using that feature now and I can't easily test
> it.  It's on the list if anyone wants to pick it up in the future.
> 
> Version 3 was posted here:
> http://www.spinics.net/lists/dri-devel/msg130977.html
> 
> Thanks to Sean Paul and Chris Zhong for their review and testing of this
> series.
> 
> John Keeping (23):
>   drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for
>     MIPI
>   drm/rockchip: dw-mipi-dsi: pass mode in where needed
>   drm/rockchip: dw-mipi-dsi: remove mode_set hook
>   drm/rockchip: dw-mipi-dsi: fix command header writes
>   drm/rockchip: dw-mipi-dsi: fix generic packet status check
>   drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf
>   drm/rockchip: dw-mipi-dsi: include bad value in error message
>   drm/rockchip: dw-mipi-dsi: respect message flags
>   drm/rockchip: dw-mipi-dsi: only request HS clock when required
>   drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned
>   drm/rockchip: dw-mipi-dsi: prepare panel after phy init
>   drm/rockchip: dw-mipi-dsi: allow commands in panel_disable
>   drm/rockchip: dw-mipi-dsi: fix escape clock rate
>   drm/rockchip: dw-mipi-dsi: ensure PHY is reset
>   drm/rockchip: dw-mipi-dsi: configure PHY before enabling
>   drm/rockchip: dw-mipi-dsi: properly configure PHY timing
>   drm/rockchip: dw-mipi-dsi: improve PLL configuration
>   drm/rockchip: dw-mipi-dsi: use specific poll helper
>   drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC
>   drm/rockchip: vop: test for P{H,V}SYNC
>   drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
>   drm/rockchip: dw-mipi-dsi: support non-burst modes
>   drm/rockchip: dw-mipi-dsi: add reset control
> 
>  drivers/gpu/drm/rockchip/dw-mipi-dsi.c      | 325 +++++++++++++++++++---------
>  drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   4 +-
>  2 files changed, 220 insertions(+), 109 deletions(-)

Applied to drm-misc

Thanks,

Sean
> 
> -- 
> 2.12.0.rc0.230.gf625d4cdb9.dirty
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel