* [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-13 14:53 ` Leo Yan
0 siblings, 0 replies; 14+ messages in thread
From: Leo Yan @ 2017-12-13 14:53 UTC (permalink / raw)
To: linux-arm-kernel
Hi Valentin,
On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
> The following dt entries are added:
> cpus [0-3] (Cortex A53):
> - capacity-dmips-mhz = <592>;
>
> cpus [4-7] (Cortex A73):
> - capacity-dmips-mhz = <1024>;
>
> Those values were obtained by running dhrystone 2.1 on a
> HiKey960 with the following procedure:
> - Offline all CPUs but CPU0 (A53)
> - Set CPU0 frequency to maximum
> - Run Dhrystone 2.1 for 20 seconds
>
> - Offline all CPUs but CPU4 (A73)
> - set CPU4 frequency to maximum
> - Run Dhrystone 2.1 for 20 seconds
>
> The results are as follows:
> A53: 129633887 loops
> A73: 287034147 loops
Seems to me the capacity-dmips-mhz should be:
CA53: 129633887 / 20 / 1844 = 3515
CA73: 287034147 / 20 / 2362 = 6076
After normalized to range [0..1024], we could get:
CA53: 592
CA73: 1024
Reviewed-by: Leo Yan <leo.yan@linaro.org>
> By scaling those values so that the A73s use 1024, we end up with 462
> for the A53s. However, they have different maximum frequencies:
> 1.844GHz for A53s and 2.362GHz for A73s. Thus, we can scale the A53
> value to truly represent dmips per MHz, and we end up with 592.
>
> The impact of this change can be verified on HiKey960:
>
> $ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
> 1844000
> 1844000
> 1844000
> 1844000
> 2362000
> 2362000
> 2362000
> 2362000
>
> $ cat /sys/devices/system/cpu/cpu*/cpu_capacity
> 462
> 462
> 462
> 462
> 1024
> 1024
> 1024
> 1024
>
> Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
> ---
> arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
> index ab0b95b..04a8d28 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
> @@ -61,6 +61,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu1: cpu at 1 {
> @@ -70,6 +71,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu2: cpu at 2 {
> @@ -79,6 +81,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu3: cpu at 3 {
> @@ -88,6 +91,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu4: cpu at 100 {
> @@ -101,6 +105,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> cpu5: cpu at 101 {
> @@ -114,6 +119,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> cpu6: cpu at 102 {
> @@ -127,6 +133,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> cpu7: cpu at 103 {
> @@ -140,6 +147,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> idle-states {
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-13 14:53 ` Leo Yan
0 siblings, 0 replies; 14+ messages in thread
From: Leo Yan @ 2017-12-13 14:53 UTC (permalink / raw)
To: Valentin Schneider
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Wei Xu, Rob Herring,
Mark Rutland, Catalin Marinas, Will Deacon, Dietmar Eggemann,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
Hi Valentin,
On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
> The following dt entries are added:
> cpus [0-3] (Cortex A53):
> - capacity-dmips-mhz = <592>;
>
> cpus [4-7] (Cortex A73):
> - capacity-dmips-mhz = <1024>;
>
> Those values were obtained by running dhrystone 2.1 on a
> HiKey960 with the following procedure:
> - Offline all CPUs but CPU0 (A53)
> - Set CPU0 frequency to maximum
> - Run Dhrystone 2.1 for 20 seconds
>
> - Offline all CPUs but CPU4 (A73)
> - set CPU4 frequency to maximum
> - Run Dhrystone 2.1 for 20 seconds
>
> The results are as follows:
> A53: 129633887 loops
> A73: 287034147 loops
Seems to me the capacity-dmips-mhz should be:
CA53: 129633887 / 20 / 1844 = 3515
CA73: 287034147 / 20 / 2362 = 6076
After normalized to range [0..1024], we could get:
CA53: 592
CA73: 1024
Reviewed-by: Leo Yan <leo.yan-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> By scaling those values so that the A73s use 1024, we end up with 462
> for the A53s. However, they have different maximum frequencies:
> 1.844GHz for A53s and 2.362GHz for A73s. Thus, we can scale the A53
> value to truly represent dmips per MHz, and we end up with 592.
>
> The impact of this change can be verified on HiKey960:
>
> $ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
> 1844000
> 1844000
> 1844000
> 1844000
> 2362000
> 2362000
> 2362000
> 2362000
>
> $ cat /sys/devices/system/cpu/cpu*/cpu_capacity
> 462
> 462
> 462
> 462
> 1024
> 1024
> 1024
> 1024
>
> Signed-off-by: Valentin Schneider <valentin.schneider-5wv7dgnIgG8@public.gmane.org>
> ---
> arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
> index ab0b95b..04a8d28 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
> @@ -61,6 +61,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu1: cpu@1 {
> @@ -70,6 +71,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu2: cpu@2 {
> @@ -79,6 +81,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu3: cpu@3 {
> @@ -88,6 +91,7 @@
> enable-method = "psci";
> next-level-cache = <&A53_L2>;
> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
> + capacity-dmips-mhz = <592>;
> };
>
> cpu4: cpu@100 {
> @@ -101,6 +105,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> cpu5: cpu@101 {
> @@ -114,6 +119,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> cpu6: cpu@102 {
> @@ -127,6 +133,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> cpu7: cpu@103 {
> @@ -140,6 +147,7 @@
> &CPU_SLEEP
> &CLUSTER_SLEEP_1
> >;
> + capacity-dmips-mhz = <1024>;
> };
>
> idle-states {
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
2017-12-13 14:53 ` Leo Yan
(?)
@ 2017-12-13 15:16 ` Valentin Schneider
-1 siblings, 0 replies; 14+ messages in thread
From: Valentin Schneider @ 2017-12-13 15:16 UTC (permalink / raw)
To: Leo Yan
Cc: linux-kernel, Wei Xu, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Dietmar Eggemann, linux-arm-kernel, devicetree
Hi Leo,
On 12/13/2017 02:53 PM, Leo Yan wrote:
> Hi Valentin,
>
> On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
>> The following dt entries are added:
>> cpus [0-3] (Cortex A53):
>> - capacity-dmips-mhz = <592>;
>>
>> cpus [4-7] (Cortex A73):
>> - capacity-dmips-mhz = <1024>;
>>
>> Those values were obtained by running dhrystone 2.1 on a
>> HiKey960 with the following procedure:
>> - Offline all CPUs but CPU0 (A53)
>> - Set CPU0 frequency to maximum
>> - Run Dhrystone 2.1 for 20 seconds
>>
>> - Offline all CPUs but CPU4 (A73)
>> - set CPU4 frequency to maximum
>> - Run Dhrystone 2.1 for 20 seconds
>>
>> The results are as follows:
>> A53: 129633887 loops
>> A73: 287034147 loops
> Seems to me the capacity-dmips-mhz should be:
>
> CA53: 129633887 / 20 / 1844 = 3515
> CA73: 287034147 / 20 / 2362 = 6076
>
> After normalized to range [0..1024], we could get:
>
> CA53: 592
> CA73: 1024
Yes, that's the "direct approach". I wanted to underline the fact that
there are two different max frequencies so what I followed would be:
1) Computing the performance ratio:
(129633887 / 287034147) * 1024 = 462.47
2) Scaling that to the same frequency scale:
462.47 * (2362/1844) = 592.38
Which gives the same end result (it's the same equation but split in two
steps). Also it makes it easy to check that the cpu_capacity sysfs entry
for the A53s gets correctly set (to 462).
>
> Reviewed-by: Leo Yan <leo.yan@linaro.org>
>
>> By scaling those values so that the A73s use 1024, we end up with 462
>> for the A53s. However, they have different maximum frequencies:
>> 1.844GHz for A53s and 2.362GHz for A73s. Thus, we can scale the A53
>> value to truly represent dmips per MHz, and we end up with 592.
>>
>> The impact of this change can be verified on HiKey960:
>>
>> $ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
>> 1844000
>> 1844000
>> 1844000
>> 1844000
>> 2362000
>> 2362000
>> 2362000
>> 2362000
>>
>> $ cat /sys/devices/system/cpu/cpu*/cpu_capacity
>> 462
>> 462
>> 462
>> 462
>> 1024
>> 1024
>> 1024
>> 1024
>>
>> Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
>> ---
>> arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 8 ++++++++
>> 1 file changed, 8 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> index ab0b95b..04a8d28 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> @@ -61,6 +61,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu1: cpu@1 {
>> @@ -70,6 +71,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu2: cpu@2 {
>> @@ -79,6 +81,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu3: cpu@3 {
>> @@ -88,6 +91,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu4: cpu@100 {
>> @@ -101,6 +105,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu5: cpu@101 {
>> @@ -114,6 +119,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu6: cpu@102 {
>> @@ -127,6 +133,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu7: cpu@103 {
>> @@ -140,6 +147,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> idle-states {
>> --
>> 2.7.4
>>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-13 15:16 ` Valentin Schneider
0 siblings, 0 replies; 14+ messages in thread
From: Valentin Schneider @ 2017-12-13 15:16 UTC (permalink / raw)
To: linux-arm-kernel
Hi Leo,
On 12/13/2017 02:53 PM, Leo Yan wrote:
> Hi Valentin,
>
> On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
>> The following dt entries are added:
>> cpus [0-3] (Cortex A53):
>> - capacity-dmips-mhz = <592>;
>>
>> cpus [4-7] (Cortex A73):
>> - capacity-dmips-mhz = <1024>;
>>
>> Those values were obtained by running dhrystone 2.1 on a
>> HiKey960 with the following procedure:
>> - Offline all CPUs but CPU0 (A53)
>> - Set CPU0 frequency to maximum
>> - Run Dhrystone 2.1 for 20 seconds
>>
>> - Offline all CPUs but CPU4 (A73)
>> - set CPU4 frequency to maximum
>> - Run Dhrystone 2.1 for 20 seconds
>>
>> The results are as follows:
>> A53: 129633887 loops
>> A73: 287034147 loops
> Seems to me the capacity-dmips-mhz should be:
>
> CA53: 129633887 / 20 / 1844 = 3515
> CA73: 287034147 / 20 / 2362 = 6076
>
> After normalized to range [0..1024], we could get:
>
> CA53: 592
> CA73: 1024
Yes, that's the "direct approach". I wanted to underline the fact that
there are two different max frequencies so what I followed would be:
1) Computing the performance ratio:
(129633887 / 287034147) * 1024 = 462.47
2) Scaling that to the same frequency scale:
462.47 * (2362/1844) = 592.38
Which gives the same end result (it's the same equation but split in two
steps). Also it makes it easy to check that the cpu_capacity sysfs entry
for the A53s gets correctly set (to 462).
>
> Reviewed-by: Leo Yan <leo.yan@linaro.org>
>
>> By scaling those values so that the A73s use 1024, we end up with 462
>> for the A53s. However, they have different maximum frequencies:
>> 1.844GHz for A53s and 2.362GHz for A73s. Thus, we can scale the A53
>> value to truly represent dmips per MHz, and we end up with 592.
>>
>> The impact of this change can be verified on HiKey960:
>>
>> $ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
>> 1844000
>> 1844000
>> 1844000
>> 1844000
>> 2362000
>> 2362000
>> 2362000
>> 2362000
>>
>> $ cat /sys/devices/system/cpu/cpu*/cpu_capacity
>> 462
>> 462
>> 462
>> 462
>> 1024
>> 1024
>> 1024
>> 1024
>>
>> Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
>> ---
>> arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 8 ++++++++
>> 1 file changed, 8 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> index ab0b95b..04a8d28 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> @@ -61,6 +61,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu1: cpu at 1 {
>> @@ -70,6 +71,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu2: cpu at 2 {
>> @@ -79,6 +81,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu3: cpu at 3 {
>> @@ -88,6 +91,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu4: cpu at 100 {
>> @@ -101,6 +105,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu5: cpu at 101 {
>> @@ -114,6 +119,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu6: cpu at 102 {
>> @@ -127,6 +133,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu7: cpu at 103 {
>> @@ -140,6 +147,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> idle-states {
>> --
>> 2.7.4
>>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-13 15:16 ` Valentin Schneider
0 siblings, 0 replies; 14+ messages in thread
From: Valentin Schneider @ 2017-12-13 15:16 UTC (permalink / raw)
To: Leo Yan
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Wei Xu, Rob Herring,
Mark Rutland, Catalin Marinas, Will Deacon, Dietmar Eggemann,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
Hi Leo,
On 12/13/2017 02:53 PM, Leo Yan wrote:
> Hi Valentin,
>
> On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
>> The following dt entries are added:
>> cpus [0-3] (Cortex A53):
>> - capacity-dmips-mhz = <592>;
>>
>> cpus [4-7] (Cortex A73):
>> - capacity-dmips-mhz = <1024>;
>>
>> Those values were obtained by running dhrystone 2.1 on a
>> HiKey960 with the following procedure:
>> - Offline all CPUs but CPU0 (A53)
>> - Set CPU0 frequency to maximum
>> - Run Dhrystone 2.1 for 20 seconds
>>
>> - Offline all CPUs but CPU4 (A73)
>> - set CPU4 frequency to maximum
>> - Run Dhrystone 2.1 for 20 seconds
>>
>> The results are as follows:
>> A53: 129633887 loops
>> A73: 287034147 loops
> Seems to me the capacity-dmips-mhz should be:
>
> CA53: 129633887 / 20 / 1844 = 3515
> CA73: 287034147 / 20 / 2362 = 6076
>
> After normalized to range [0..1024], we could get:
>
> CA53: 592
> CA73: 1024
Yes, that's the "direct approach". I wanted to underline the fact that
there are two different max frequencies so what I followed would be:
1) Computing the performance ratio:
(129633887 / 287034147) * 1024 = 462.47
2) Scaling that to the same frequency scale:
462.47 * (2362/1844) = 592.38
Which gives the same end result (it's the same equation but split in two
steps). Also it makes it easy to check that the cpu_capacity sysfs entry
for the A53s gets correctly set (to 462).
>
> Reviewed-by: Leo Yan <leo.yan-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
>
>> By scaling those values so that the A73s use 1024, we end up with 462
>> for the A53s. However, they have different maximum frequencies:
>> 1.844GHz for A53s and 2.362GHz for A73s. Thus, we can scale the A53
>> value to truly represent dmips per MHz, and we end up with 592.
>>
>> The impact of this change can be verified on HiKey960:
>>
>> $ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
>> 1844000
>> 1844000
>> 1844000
>> 1844000
>> 2362000
>> 2362000
>> 2362000
>> 2362000
>>
>> $ cat /sys/devices/system/cpu/cpu*/cpu_capacity
>> 462
>> 462
>> 462
>> 462
>> 1024
>> 1024
>> 1024
>> 1024
>>
>> Signed-off-by: Valentin Schneider <valentin.schneider-5wv7dgnIgG8@public.gmane.org>
>> ---
>> arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 8 ++++++++
>> 1 file changed, 8 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> index ab0b95b..04a8d28 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> @@ -61,6 +61,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu1: cpu@1 {
>> @@ -70,6 +71,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu2: cpu@2 {
>> @@ -79,6 +81,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu3: cpu@3 {
>> @@ -88,6 +91,7 @@
>> enable-method = "psci";
>> next-level-cache = <&A53_L2>;
>> cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
>> + capacity-dmips-mhz = <592>;
>> };
>>
>> cpu4: cpu@100 {
>> @@ -101,6 +105,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu5: cpu@101 {
>> @@ -114,6 +119,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu6: cpu@102 {
>> @@ -127,6 +133,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> cpu7: cpu@103 {
>> @@ -140,6 +147,7 @@
>> &CPU_SLEEP
>> &CLUSTER_SLEEP_1
>> >;
>> + capacity-dmips-mhz = <1024>;
>> };
>>
>> idle-states {
>> --
>> 2.7.4
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-14 1:07 ` Leo Yan
0 siblings, 0 replies; 14+ messages in thread
From: Leo Yan @ 2017-12-14 1:07 UTC (permalink / raw)
To: Valentin Schneider
Cc: linux-kernel, Wei Xu, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Dietmar Eggemann, linux-arm-kernel, devicetree
On Wed, Dec 13, 2017 at 03:16:13PM +0000, Valentin Schneider wrote:
> Hi Leo,
>
>
> On 12/13/2017 02:53 PM, Leo Yan wrote:
> >Hi Valentin,
> >
> >On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
> >>The following dt entries are added:
> >> cpus [0-3] (Cortex A53):
> >> - capacity-dmips-mhz = <592>;
> >>
> >> cpus [4-7] (Cortex A73):
> >> - capacity-dmips-mhz = <1024>;
> >>
> >>Those values were obtained by running dhrystone 2.1 on a
> >>HiKey960 with the following procedure:
> >>- Offline all CPUs but CPU0 (A53)
> >>- Set CPU0 frequency to maximum
> >>- Run Dhrystone 2.1 for 20 seconds
> >>
> >>- Offline all CPUs but CPU4 (A73)
> >>- set CPU4 frequency to maximum
> >>- Run Dhrystone 2.1 for 20 seconds
> >>
> >>The results are as follows:
> >>A53: 129633887 loops
> >>A73: 287034147 loops
> >Seems to me the capacity-dmips-mhz should be:
> >
> >CA53: 129633887 / 20 / 1844 = 3515
> >CA73: 287034147 / 20 / 2362 = 6076
> >
> >After normalized to range [0..1024], we could get:
> >
> >CA53: 592
> >CA73: 1024
>
> Yes, that's the "direct approach". I wanted to underline the fact that there
> are two different max frequencies so what I followed would be:
>
> 1) Computing the performance ratio:
> (129633887 / 287034147) * 1024 = 462.47
>
> 2) Scaling that to the same frequency scale:
> 462.47 * (2362/1844) = 592.38
>
> Which gives the same end result (it's the same equation but split in two
> steps). Also it makes it easy to check that the cpu_capacity sysfs entry for
> the A53s gets correctly set (to 462).
Yeah, thanks for clear explanation.
[...]
Thanks,
Leo Yan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-14 1:07 ` Leo Yan
0 siblings, 0 replies; 14+ messages in thread
From: Leo Yan @ 2017-12-14 1:07 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Dec 13, 2017 at 03:16:13PM +0000, Valentin Schneider wrote:
> Hi Leo,
>
>
> On 12/13/2017 02:53 PM, Leo Yan wrote:
> >Hi Valentin,
> >
> >On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
> >>The following dt entries are added:
> >> cpus [0-3] (Cortex A53):
> >> - capacity-dmips-mhz = <592>;
> >>
> >> cpus [4-7] (Cortex A73):
> >> - capacity-dmips-mhz = <1024>;
> >>
> >>Those values were obtained by running dhrystone 2.1 on a
> >>HiKey960 with the following procedure:
> >>- Offline all CPUs but CPU0 (A53)
> >>- Set CPU0 frequency to maximum
> >>- Run Dhrystone 2.1 for 20 seconds
> >>
> >>- Offline all CPUs but CPU4 (A73)
> >>- set CPU4 frequency to maximum
> >>- Run Dhrystone 2.1 for 20 seconds
> >>
> >>The results are as follows:
> >>A53: 129633887 loops
> >>A73: 287034147 loops
> >Seems to me the capacity-dmips-mhz should be:
> >
> >CA53: 129633887 / 20 / 1844 = 3515
> >CA73: 287034147 / 20 / 2362 = 6076
> >
> >After normalized to range [0..1024], we could get:
> >
> >CA53: 592
> >CA73: 1024
>
> Yes, that's the "direct approach". I wanted to underline the fact that there
> are two different max frequencies so what I followed would be:
>
> 1) Computing the performance ratio:
> (129633887 / 287034147) * 1024 = 462.47
>
> 2) Scaling that to the same frequency scale:
> 462.47 * (2362/1844) = 592.38
>
> Which gives the same end result (it's the same equation but split in two
> steps). Also it makes it easy to check that the cpu_capacity sysfs entry for
> the A53s gets correctly set (to 462).
Yeah, thanks for clear explanation.
[...]
Thanks,
Leo Yan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH] arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
@ 2017-12-14 1:07 ` Leo Yan
0 siblings, 0 replies; 14+ messages in thread
From: Leo Yan @ 2017-12-14 1:07 UTC (permalink / raw)
To: Valentin Schneider
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Wei Xu, Rob Herring,
Mark Rutland, Catalin Marinas, Will Deacon, Dietmar Eggemann,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
On Wed, Dec 13, 2017 at 03:16:13PM +0000, Valentin Schneider wrote:
> Hi Leo,
>
>
> On 12/13/2017 02:53 PM, Leo Yan wrote:
> >Hi Valentin,
> >
> >On Wed, Dec 13, 2017 at 02:21:06PM +0000, Valentin Schneider wrote:
> >>The following dt entries are added:
> >> cpus [0-3] (Cortex A53):
> >> - capacity-dmips-mhz = <592>;
> >>
> >> cpus [4-7] (Cortex A73):
> >> - capacity-dmips-mhz = <1024>;
> >>
> >>Those values were obtained by running dhrystone 2.1 on a
> >>HiKey960 with the following procedure:
> >>- Offline all CPUs but CPU0 (A53)
> >>- Set CPU0 frequency to maximum
> >>- Run Dhrystone 2.1 for 20 seconds
> >>
> >>- Offline all CPUs but CPU4 (A73)
> >>- set CPU4 frequency to maximum
> >>- Run Dhrystone 2.1 for 20 seconds
> >>
> >>The results are as follows:
> >>A53: 129633887 loops
> >>A73: 287034147 loops
> >Seems to me the capacity-dmips-mhz should be:
> >
> >CA53: 129633887 / 20 / 1844 = 3515
> >CA73: 287034147 / 20 / 2362 = 6076
> >
> >After normalized to range [0..1024], we could get:
> >
> >CA53: 592
> >CA73: 1024
>
> Yes, that's the "direct approach". I wanted to underline the fact that there
> are two different max frequencies so what I followed would be:
>
> 1) Computing the performance ratio:
> (129633887 / 287034147) * 1024 = 462.47
>
> 2) Scaling that to the same frequency scale:
> 462.47 * (2362/1844) = 592.38
>
> Which gives the same end result (it's the same equation but split in two
> steps). Also it makes it easy to check that the cpu_capacity sysfs entry for
> the A53s gets correctly set (to 462).
Yeah, thanks for clear explanation.
[...]
Thanks,
Leo Yan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread