[PATCH 5.10.y-cip 00/27] Add RPCIF, SCI{F1} support to Renesas RZ/G2L SoC

[PATCH 5.10.y-cip 00/27] Add RPCIF, SCI{F1} support to Renesas RZ/G2L SoC

[Lad Prabhakar]

Hi All,

This patch series add support for the below:
* Adds a generic property "output-impedance-ohms"
* Pinctrl driver update to support set/get drive-strength and
  output-impedance-ohms
* Driver fixes and updates for RPC-IF
* Support to SPI Multi I/O Bus controller (RPC-IF) for RZ/G2L
* Support to SCI for RZ/G2L SoC
* DTS updates for RZ/G2L SMARC

All the patches have been cherry-picked from Linux v5.17-rc2.

Cheers,
Prabhakar

Biju Das (1):
  arm64: dts: renesas: r9a07g044: Sort psci node

Geert Uytterhoeven (1):
  dt-bindings: memory: renesas,rpc-if: Miscellaneous improvements

Krzysztof Kozlowski (1):
  memory: renesas-rpc-if: correct whitespace

Lad Prabhakar (24):
  dt-bindings: pincfg-node: Add "output-impedance-ohms" property
  pinctrl: pinconf-generic: Add support for "output-impedance-ohms" to
    be extracted from DT files
  dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Add output-impedance-ohms
    property
  pinctrl: renesas: rzg2l: Rename RZG2L_SINGLE_PIN_GET_PORT macro
  pinctrl: renesas: rzg2l: Add helper functions to read/write pin config
  pinctrl: renesas: rzg2l: Add support to get/set pin config for GPIO
    port pins
  pinctrl: renesas: rzg2l: Rename PIN_CFG_* macros to match HW manual
  pinctrl: renesas: rzg2l: Add support to get/set drive-strength and
    output-impedance-ohms
  dt-bindings: memory: renesas,rpc-if: Add support for the R9A07G044
  dt-bindings: memory: renesas,rpc-if: Add optional interrupts property
  mtd: hyperbus: rpc-if: Check return value of rpcif_sw_init()
  memory: renesas-rpc-if: Return error in case devm_ioremap_resource()
    fails
  memory: renesas-rpc-if: Drop usage of RPCIF_DIRMAP_SIZE macro
  memory: renesas-rpc-if: Add support for RZ/G2L
  clk: renesas: r9a07g044: Add clock and reset entries for SPI Multi I/O
    Bus Controller
  arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node
  arm64: dts: renesas: rzg2l-smarc-som: Enable serial NOR flash
  clk: renesas: r9a07g044: Add clock and reset entry for SCI1
  dt-bindings: serial: renesas,scif: Make resets as a required property
  dt-bindings: serial: renesas,sci: Document RZ/G2L SoC
  serial: sh-sci: Add support to deassert/assert reset line
  arm64: dts: renesas: r9a07g044: Add SCIF[1-4] nodes
  arm64: dts: renesas: rzg2l-smarc: Enable SCIF2 on carrier board
  arm64: dts: renesas: r9a07g044: Add SCI[0-1] nodes

 .../memory-controllers/renesas,rpc-if.yaml    |  55 +++-
 .../bindings/pinctrl/pincfg-node.yaml         |   3 +
 .../pinctrl/renesas,rzg2l-pinctrl.yaml        |   2 +
 .../bindings/serial/renesas,sci.yaml          |  46 ++-
 .../bindings/serial/renesas,scif.yaml         |   1 +
 arch/arm64/boot/dts/renesas/r9a07g044.dtsi    | 129 +++++++-
 .../boot/dts/renesas/rzg2l-smarc-som.dtsi     |  40 +++
 arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi  |  28 ++
 drivers/clk/renesas/r9a07g044-cpg.c           |  21 ++
 drivers/clk/renesas/rzg2l-cpg.h               |   3 +
 drivers/memory/renesas-rpc-if.c               |  80 ++++-
 drivers/mtd/hyperbus/rpc-if.c                 |   8 +-
 drivers/pinctrl/pinconf-generic.c             |   2 +
 drivers/pinctrl/renesas/pinctrl-rzg2l.c       | 310 ++++++++++++------
 drivers/spi/spi-rpc-if.c                      |   4 +-
 drivers/tty/serial/sh-sci.c                   |  39 ++-
 include/linux/pinctrl/pinconf-generic.h       |   3 +
 include/memory/renesas-rpc-if.h               |  14 +-
 18 files changed, 639 insertions(+), 149 deletions(-)

-- 
2.17.1

[PATCH 5.10.y-cip 01/27] dt-bindings: pincfg-node: Add "output-impedance-ohms" property

[Lad Prabhakar]

commit 7388fa8acfce2c3b41babc53c3f3d0b247b098af upstream.

On RZ/G2L SoC for Group-B pins, output impedance can be configured. This
patch documents "output-impedance-ohms" property in pincfg-node.yaml so
that other platforms requiring such feature can make use of this property.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211027134509.5036-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
index 71ed0a9def84..4b22a9e3a447 100644
--- a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
@@ -114,6 +114,9 @@ properties:
     description: enable output on a pin without actively driving it
       (such as enabling an output buffer)
 
+  output-impedance-ohms:
+    description: set the output impedance of a pin to at most X ohms
+
   output-low:
     type: boolean
     description: set the pin to output mode with low level
-- 
2.17.1

[PATCH 5.10.y-cip 02/27] pinctrl: pinconf-generic: Add support for "output-impedance-ohms" to be extracted from DT files

[Lad Prabhakar]

commit 032816fbbfafe3198bb5c71fbbe4e8e5be33b352 upstream.

Add "output-impedance-ohms" property to generic options used for DT
parsing files. This enables drivers, which use generic pin configurations,
to get the value passed to this property.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211027134509.5036-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[PL: Manually applied the changes.]
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/pinctrl/pinconf-generic.c       | 2 ++
 include/linux/pinctrl/pinconf-generic.h | 3 +++
 2 files changed, 5 insertions(+)

diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c
index 1e225d513988..fcf261aa532e 100644
--- a/drivers/pinctrl/pinconf-generic.c
+++ b/drivers/pinctrl/pinconf-generic.c
@@ -46,6 +46,7 @@ static const struct pin_config_item conf_items[] = {
 	PCONFDUMP(PIN_CONFIG_LOW_POWER_MODE, "pin low power", "mode", true),
 	PCONFDUMP(PIN_CONFIG_OUTPUT_ENABLE, "output enabled", NULL, false),
 	PCONFDUMP(PIN_CONFIG_OUTPUT, "pin output", "level", true),
+	PCONFDUMP(PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS, "output impedance", "ohms", true),
 	PCONFDUMP(PIN_CONFIG_POWER_SOURCE, "pin power source", "selector", true),
 	PCONFDUMP(PIN_CONFIG_SLEEP_HARDWARE_STATE, "sleep hardware state", NULL, false),
 	PCONFDUMP(PIN_CONFIG_SLEW_RATE, "slew rate", NULL, true),
@@ -179,6 +180,7 @@ static const struct pinconf_generic_params dt_params[] = {
 	{ "output-disable", PIN_CONFIG_OUTPUT_ENABLE, 0 },
 	{ "output-enable", PIN_CONFIG_OUTPUT_ENABLE, 1 },
 	{ "output-high", PIN_CONFIG_OUTPUT, 1, },
+	{ "output-impedance-ohms", PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS, 0 },
 	{ "output-low", PIN_CONFIG_OUTPUT, 0, },
 	{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
 	{ "sleep-hardware-state", PIN_CONFIG_SLEEP_HARDWARE_STATE, 0 },
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index 6aeb711f7cd1..545e598abb0f 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -90,6 +90,8 @@ struct pinctrl_map;
  * 	value on the line. Use argument 1 to indicate high level, argument 0 to
  *	indicate low level. (Please see Documentation/driver-api/pinctl.rst,
  *	section "GPIO mode pitfalls" for a discussion around this parameter.)
+ * @PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS: this will configure the output impedance
+ * 	of the pin with the value passed as argument. The argument is in ohms.
  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  *	supplies, the argument to this parameter (on a custom format) tells
  *	the driver which alternative power source to use.
@@ -127,6 +129,7 @@ enum pin_config_param {
 	PIN_CONFIG_LOW_POWER_MODE,
 	PIN_CONFIG_OUTPUT_ENABLE,
 	PIN_CONFIG_OUTPUT,
+	PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS,
 	PIN_CONFIG_POWER_SOURCE,
 	PIN_CONFIG_SLEEP_HARDWARE_STATE,
 	PIN_CONFIG_SLEW_RATE,
-- 
2.17.1

[PATCH 5.10.y-cip 03/27] dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Add output-impedance-ohms property

[Lad Prabhakar]

commit aa52b008441fb5a5df01c1d016e5172d2ebc6579 upstream.

RZ/G2L SoC has two groups of pins, Group-A and Group-B. RZ/G2L SoC supports
configuring Output Impedance for Group-B pins (valid values 33/50/66/100).

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211110224622.16022-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 .../devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml      | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
index ef68dabcf4dc..3a66fd214c17 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
@@ -73,6 +73,8 @@ additionalProperties:
         pins: true
         drive-strength:
           enum: [ 2, 4, 8, 12 ]
+        output-impedance-ohms:
+          enum: [ 33, 50, 66, 100 ]
         power-source:
           enum: [ 1800, 2500, 3300 ]
         slew-rate: true
-- 
2.17.1

[PATCH 5.10.y-cip 04/27] pinctrl: renesas: rzg2l: Rename RZG2L_SINGLE_PIN_GET_PORT macro

[Lad Prabhakar]

commit c76629a63b9c7cc52bb661aa36081c0c87780c3b upstream.

Rename RZG2L_SINGLE_PIN_GET_PORT -> RZG2L_SINGLE_PIN_GET_PORT_OFFSET.

Also, rename port -> port_offset in rzg2l_pinctrl_pinconf_set/get for
readability.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110224622.16022-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 20b2af889ca9..be9af717a497 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -77,7 +77,7 @@
 #define RZG2L_SINGLE_PIN		BIT(31)
 #define RZG2L_SINGLE_PIN_PACK(p, b, f)	(RZG2L_SINGLE_PIN | \
 					 ((p) << 24) | ((b) << 20) | (f))
-#define RZG2L_SINGLE_PIN_GET_PORT(x)	(((x) & GENMASK(30, 24)) >> 24)
+#define RZG2L_SINGLE_PIN_GET_PORT_OFFSET(x)	(((x) & GENMASK(30, 24)) >> 24)
 #define RZG2L_SINGLE_PIN_GET_BIT(x)	(((x) & GENMASK(22, 20)) >> 20)
 #define RZG2L_SINGLE_PIN_GET_CFGS(x)	((x) & GENMASK(19, 0))
 
@@ -432,10 +432,10 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	enum pin_config_param param = pinconf_to_config_param(*config);
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
+	u32 port_offset = 0, reg;
 	unsigned int arg = 0;
 	unsigned long flags;
 	void __iomem *addr;
-	u32 port = 0, reg;
 	u32 cfg = 0;
 	u8 bit = 0;
 
@@ -443,7 +443,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 		return -EINVAL;
 
 	if (*pin_data & RZG2L_SINGLE_PIN) {
-		port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
+		port_offset = RZG2L_SINGLE_PIN_GET_PORT_OFFSET(*pin_data);
 		cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
 		bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
 	}
@@ -454,7 +454,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 			return -EINVAL;
 		spin_lock_irqsave(&pctrl->lock, flags);
 		/* handle _L/_H for 32-bit register read/write */
-		addr = pctrl->base + IEN(port);
+		addr = pctrl->base + IEN(port_offset);
 		if (bit >= 4) {
 			bit -= 4;
 			addr += 4;
@@ -502,9 +502,9 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
 	enum pin_config_param param;
+	u32 port_offset = 0, reg;
 	unsigned long flags;
 	void __iomem *addr;
-	u32 port = 0, reg;
 	unsigned int i;
 	u32 cfg = 0;
 	u8 bit = 0;
@@ -513,7 +513,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 		return -EINVAL;
 
 	if (*pin_data & RZG2L_SINGLE_PIN) {
-		port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
+		port_offset = RZG2L_SINGLE_PIN_GET_PORT_OFFSET(*pin_data);
 		cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
 		bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
 	}
@@ -529,7 +529,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 				return -EINVAL;
 
 			/* handle _L/_H for 32-bit register read/write */
-			addr = pctrl->base + IEN(port);
+			addr = pctrl->base + IEN(port_offset);
 			if (bit >= 4) {
 				bit -= 4;
 				addr += 4;
-- 
2.17.1

[PATCH 5.10.y-cip 05/27] pinctrl: renesas: rzg2l: Add helper functions to read/write pin config

[Lad Prabhakar]

commit d1189991c823b50990291c8157b56fb141c47155 upstream.

Add helper functions to read/read modify write pin config.

Switch to use helper functions for pins supporting PIN_CONFIG_INPUT_ENABLE
capabilities.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110224622.16022-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 61 +++++++++++++++----------
 1 file changed, 37 insertions(+), 24 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index be9af717a497..4465402367f9 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -424,6 +424,39 @@ static int rzg2l_dt_node_to_map(struct pinctrl_dev *pctldev,
 	return ret;
 }
 
+static u32 rzg2l_read_pin_config(struct rzg2l_pinctrl *pctrl, u32 offset,
+				 u8 bit, u32 mask)
+{
+	void __iomem *addr = pctrl->base + offset;
+
+	/* handle _L/_H for 32-bit register read/write */
+	if (bit >= 4) {
+		bit -= 4;
+		addr += 4;
+	}
+
+	return (readl(addr) >> (bit * 8)) & mask;
+}
+
+static void rzg2l_rmw_pin_config(struct rzg2l_pinctrl *pctrl, u32 offset,
+				 u8 bit, u32 mask, u32 val)
+{
+	void __iomem *addr = pctrl->base + offset;
+	unsigned long flags;
+	u32 reg;
+
+	/* handle _L/_H for 32-bit register read/write */
+	if (bit >= 4) {
+		bit -= 4;
+		addr += 4;
+	}
+
+	spin_lock_irqsave(&pctrl->lock, flags);
+	reg = readl(addr) & ~(mask << (bit * 8));
+	writel(reg | (val << (bit * 8)), addr);
+	spin_unlock_irqrestore(&pctrl->lock, flags);
+}
+
 static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 				     unsigned int _pin,
 				     unsigned long *config)
@@ -432,8 +465,8 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	enum pin_config_param param = pinconf_to_config_param(*config);
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
-	u32 port_offset = 0, reg;
 	unsigned int arg = 0;
+	u32 port_offset = 0;
 	unsigned long flags;
 	void __iomem *addr;
 	u32 cfg = 0;
@@ -452,17 +485,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	case PIN_CONFIG_INPUT_ENABLE:
 		if (!(cfg & PIN_CFG_IEN))
 			return -EINVAL;
-		spin_lock_irqsave(&pctrl->lock, flags);
-		/* handle _L/_H for 32-bit register read/write */
-		addr = pctrl->base + IEN(port_offset);
-		if (bit >= 4) {
-			bit -= 4;
-			addr += 4;
-		}
-
-		reg = readl(addr) & (IEN_MASK << (bit * 8));
-		arg = (reg >> (bit * 8)) & 0x1;
-		spin_unlock_irqrestore(&pctrl->lock, flags);
+		arg = rzg2l_read_pin_config(pctrl, IEN(port_offset), bit, IEN_MASK);
 		break;
 
 	case PIN_CONFIG_POWER_SOURCE: {
@@ -502,7 +525,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
 	enum pin_config_param param;
-	u32 port_offset = 0, reg;
+	u32 port_offset = 0;
 	unsigned long flags;
 	void __iomem *addr;
 	unsigned int i;
@@ -528,17 +551,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 			if (!(cfg & PIN_CFG_IEN))
 				return -EINVAL;
 
-			/* handle _L/_H for 32-bit register read/write */
-			addr = pctrl->base + IEN(port_offset);
-			if (bit >= 4) {
-				bit -= 4;
-				addr += 4;
-			}
-
-			spin_lock_irqsave(&pctrl->lock, flags);
-			reg = readl(addr) & ~(IEN_MASK << (bit * 8));
-			writel(reg | (arg << (bit * 8)), addr);
-			spin_unlock_irqrestore(&pctrl->lock, flags);
+			rzg2l_rmw_pin_config(pctrl, IEN(port_offset), bit, IEN_MASK, !!arg);
 			break;
 		}
 
-- 
2.17.1

[PATCH 5.10.y-cip 06/27] pinctrl: renesas: rzg2l: Add support to get/set pin config for GPIO port pins

[Lad Prabhakar]

commit 7f13a4297be04a1d5e6f025a44531d3c85c02524 upstream.

Add support to get/set pin config for GPIO port pins.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110224622.16022-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 36 +++++++++++++++++++++++--
 1 file changed, 34 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 4465402367f9..a5c4bfb59692 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -106,6 +106,7 @@
 #define PM_OUTPUT		0x2
 
 #define RZG2L_PIN_ID_TO_PORT(id)	((id) / RZG2L_PINS_PER_PORT)
+#define RZG2L_PIN_ID_TO_PORT_OFFSET(id)	(RZG2L_PIN_ID_TO_PORT(id) + 0x10)
 #define RZG2L_PIN_ID_TO_PIN(id)		((id) % RZG2L_PINS_PER_PORT)
 
 struct rzg2l_dedicated_configs {
@@ -424,6 +425,23 @@ static int rzg2l_dt_node_to_map(struct pinctrl_dev *pctldev,
 	return ret;
 }
 
+static int rzg2l_validate_gpio_pin(struct rzg2l_pinctrl *pctrl,
+				   u32 cfg, u32 port, u8 bit)
+{
+	u8 pincount = RZG2L_GPIO_PORT_GET_PINCNT(cfg);
+	u32 port_index = RZG2L_GPIO_PORT_GET_INDEX(cfg);
+	u32 data;
+
+	if (bit >= pincount || port >= pctrl->data->n_port_pins)
+		return -EINVAL;
+
+	data = pctrl->data->port_pin_configs[port];
+	if (port_index != RZG2L_GPIO_PORT_GET_INDEX(data))
+		return -EINVAL;
+
+	return 0;
+}
+
 static u32 rzg2l_read_pin_config(struct rzg2l_pinctrl *pctrl, u32 offset,
 				 u8 bit, u32 mask)
 {
@@ -466,9 +484,9 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
 	unsigned int arg = 0;
-	u32 port_offset = 0;
 	unsigned long flags;
 	void __iomem *addr;
+	u32 port_offset;
 	u32 cfg = 0;
 	u8 bit = 0;
 
@@ -479,6 +497,13 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 		port_offset = RZG2L_SINGLE_PIN_GET_PORT_OFFSET(*pin_data);
 		cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
 		bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
+	} else {
+		cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
+		port_offset = RZG2L_PIN_ID_TO_PORT_OFFSET(_pin);
+		bit = RZG2L_PIN_ID_TO_PIN(_pin);
+
+		if (rzg2l_validate_gpio_pin(pctrl, *pin_data, RZG2L_PIN_ID_TO_PORT(_pin), bit))
+			return -EINVAL;
 	}
 
 	switch (param) {
@@ -525,9 +550,9 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
 	enum pin_config_param param;
-	u32 port_offset = 0;
 	unsigned long flags;
 	void __iomem *addr;
+	u32 port_offset;
 	unsigned int i;
 	u32 cfg = 0;
 	u8 bit = 0;
@@ -539,6 +564,13 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 		port_offset = RZG2L_SINGLE_PIN_GET_PORT_OFFSET(*pin_data);
 		cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
 		bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
+	} else {
+		cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
+		port_offset = RZG2L_PIN_ID_TO_PORT_OFFSET(_pin);
+		bit = RZG2L_PIN_ID_TO_PIN(_pin);
+
+		if (rzg2l_validate_gpio_pin(pctrl, *pin_data, RZG2L_PIN_ID_TO_PORT(_pin), bit))
+			return -EINVAL;
 	}
 
 	for (i = 0; i < num_configs; i++) {
-- 
2.17.1

[PATCH 5.10.y-cip 07/27] pinctrl: renesas: rzg2l: Rename PIN_CFG_* macros to match HW manual

[Lad Prabhakar]

commit 22972a2d5bc4bae3db9521580cea8971c96204bc upstream.

Rename the below macros to match the HW manual (Rev.1.00):
PIN_CFG_IOLH_SD0 -> PIN_CFG_IO_VMC_SD0
PIN_CFG_IOLH_SD1 -> PIN_CFG_IO_VMC_SD1
PIN_CFG_IOLH_QSPI -> PIN_CFG_IO_VMC_QSPI
PIN_CFG_IOLH_ETH0 -> PIN_CFG_IO_VMC_ETH0
PIN_CFG_IOLH_ETH1 -> PIN_CFG_IO_VMC_ETH1

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110224622.16022-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 122 ++++++++++++------------
 1 file changed, 61 insertions(+), 61 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index a5c4bfb59692..5ebb9034b572 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -39,11 +39,11 @@
 #define PIN_CFG_SR			BIT(1)
 #define PIN_CFG_IEN			BIT(2)
 #define PIN_CFG_PUPD			BIT(3)
-#define PIN_CFG_IOLH_SD0		BIT(4)
-#define PIN_CFG_IOLH_SD1		BIT(5)
-#define PIN_CFG_IOLH_QSPI		BIT(6)
-#define PIN_CFG_IOLH_ETH0		BIT(7)
-#define PIN_CFG_IOLH_ETH1		BIT(8)
+#define PIN_CFG_IO_VMC_SD0		BIT(4)
+#define PIN_CFG_IO_VMC_SD1		BIT(5)
+#define PIN_CFG_IO_VMC_QSPI		BIT(6)
+#define PIN_CFG_IO_VMC_ETH0		BIT(7)
+#define PIN_CFG_IO_VMC_ETH1		BIT(8)
 #define PIN_CFG_FILONOFF		BIT(9)
 #define PIN_CFG_FILNUM			BIT(10)
 #define PIN_CFG_FILCLKSEL		BIT(11)
@@ -516,11 +516,11 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	case PIN_CONFIG_POWER_SOURCE: {
 		u32 pwr_reg = 0x0;
 
-		if (cfg & PIN_CFG_IOLH_SD0)
+		if (cfg & PIN_CFG_IO_VMC_SD0)
 			pwr_reg = SD_CH(0);
-		else if (cfg & PIN_CFG_IOLH_SD1)
+		else if (cfg & PIN_CFG_IO_VMC_SD1)
 			pwr_reg = SD_CH(1);
-		else if (cfg & PIN_CFG_IOLH_QSPI)
+		else if (cfg & PIN_CFG_IO_VMC_QSPI)
 			pwr_reg = QSPI;
 		else
 			return -EINVAL;
@@ -594,11 +594,11 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 			if (mV != 1800 && mV != 3300)
 				return -EINVAL;
 
-			if (cfg & PIN_CFG_IOLH_SD0)
+			if (cfg & PIN_CFG_IO_VMC_SD0)
 				pwr_reg = SD_CH(0);
-			else if (cfg & PIN_CFG_IOLH_SD1)
+			else if (cfg & PIN_CFG_IO_VMC_SD1)
 				pwr_reg = SD_CH(1);
-			else if (cfg & PIN_CFG_IOLH_QSPI)
+			else if (cfg & PIN_CFG_IO_VMC_QSPI)
 				pwr_reg = QSPI;
 			else
 				return -EINVAL;
@@ -900,24 +900,24 @@ static const u32 rzg2l_gpio_configs[] = {
 	RZG2L_GPIO_PORT_PACK(3, 0x21, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x22, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x23, RZG2L_MPXED_PIN_FUNCS),
-	RZG2L_GPIO_PORT_PACK(3, 0x24, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x25, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x26, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x27, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x28, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x29, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2a, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2b, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2c, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2d, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2e, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2f, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x30, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x31, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x32, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x33, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x34, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(3, 0x35, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
+	RZG2L_GPIO_PORT_PACK(3, 0x24, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x25, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x26, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x27, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x28, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x29, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2a, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2b, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2c, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2d, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2e, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2f, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x30, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x31, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x32, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x33, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x34, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(3, 0x35, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
 	RZG2L_GPIO_PORT_PACK(2, 0x36, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(3, 0x37, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(3, 0x38, RZG2L_MPXED_PIN_FUNCS),
@@ -941,68 +941,68 @@ static  struct rzg2l_dedicated_configs rzg2l_dedicated_pins[] = {
 	{ "AUDIO_CLK1", RZG2L_SINGLE_PIN_PACK(0x4, 0, PIN_CFG_IEN) },
 	{ "AUDIO_CLK2", RZG2L_SINGLE_PIN_PACK(0x4, 1, PIN_CFG_IEN) },
 	{ "SD0_CLK", RZG2L_SINGLE_PIN_PACK(0x6, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_CMD", RZG2L_SINGLE_PIN_PACK(0x6, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_RST#", RZG2L_SINGLE_PIN_PACK(0x6, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA0", RZG2L_SINGLE_PIN_PACK(0x7, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA1", RZG2L_SINGLE_PIN_PACK(0x7, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA2", RZG2L_SINGLE_PIN_PACK(0x7, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA3", RZG2L_SINGLE_PIN_PACK(0x7, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA4", RZG2L_SINGLE_PIN_PACK(0x7, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA5", RZG2L_SINGLE_PIN_PACK(0x7, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA6", RZG2L_SINGLE_PIN_PACK(0x7, 6,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA7", RZG2L_SINGLE_PIN_PACK(0x7, 7,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD1_CLK", RZG2L_SINGLE_PIN_PACK(0x8, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_SD1))},
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD1))},
 	{ "SD1_CMD", RZG2L_SINGLE_PIN_PACK(0x8, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA0", RZG2L_SINGLE_PIN_PACK(0x9, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA1", RZG2L_SINGLE_PIN_PACK(0x9, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA2", RZG2L_SINGLE_PIN_PACK(0x9, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA3", RZG2L_SINGLE_PIN_PACK(0x9, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "QSPI0_SPCLK", RZG2L_SINGLE_PIN_PACK(0xa, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO0", RZG2L_SINGLE_PIN_PACK(0xa, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO1", RZG2L_SINGLE_PIN_PACK(0xa, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO2", RZG2L_SINGLE_PIN_PACK(0xa, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO3", RZG2L_SINGLE_PIN_PACK(0xa, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_SSL", RZG2L_SINGLE_PIN_PACK(0xa, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SPCLK", RZG2L_SINGLE_PIN_PACK(0xb, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO0", RZG2L_SINGLE_PIN_PACK(0xb, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO1", RZG2L_SINGLE_PIN_PACK(0xb, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO2", RZG2L_SINGLE_PIN_PACK(0xb, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO3", RZG2L_SINGLE_PIN_PACK(0xb, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR  | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR  | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SSL", RZG2L_SINGLE_PIN_PACK(0xb, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_RESET#", RZG2L_SINGLE_PIN_PACK(0xc, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_WP#", RZG2L_SINGLE_PIN_PACK(0xc, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
-	{ "QSPI_INT#", RZG2L_SINGLE_PIN_PACK(0xc, 2, (PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	{ "QSPI_INT#", RZG2L_SINGLE_PIN_PACK(0xc, 2, (PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "WDTOVF_PERROUT#", RZG2L_SINGLE_PIN_PACK(0xd, 0, (PIN_CFG_IOLH | PIN_CFG_SR)) },
 	{ "RIIC0_SDA", RZG2L_SINGLE_PIN_PACK(0xe, 0, PIN_CFG_IEN) },
 	{ "RIIC0_SCL", RZG2L_SINGLE_PIN_PACK(0xe, 1, PIN_CFG_IEN) },
-- 
2.17.1

[PATCH 5.10.y-cip 08/27] pinctrl: renesas: rzg2l: Add support to get/set drive-strength and output-impedance-ohms

[Lad Prabhakar]

commit adb613f84a9e3638dfcc85975c7d58a4e80eef02 upstream.

RZ/G2L supports two groups of pins Group-A and Group-B. For Group-A
pins drive-strength can be configured and for Group-B output-impedance
can be configured.

This patch splits PIN_CFG_IOLH macro to PIN_CFG_IOLH_A/B and adds
support to get/set drive-strength and output-impedance-ohms for the
supported pins.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110224622.16022-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 161 +++++++++++++++++-------
 1 file changed, 113 insertions(+), 48 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 5ebb9034b572..ccee9c9e2e22 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -35,20 +35,21 @@
 #define MUX_FUNC(pinconf)	(((pinconf) & MUX_FUNC_MASK) >> MUX_FUNC_OFFS)
 
 /* PIN capabilities */
-#define PIN_CFG_IOLH			BIT(0)
-#define PIN_CFG_SR			BIT(1)
-#define PIN_CFG_IEN			BIT(2)
-#define PIN_CFG_PUPD			BIT(3)
-#define PIN_CFG_IO_VMC_SD0		BIT(4)
-#define PIN_CFG_IO_VMC_SD1		BIT(5)
-#define PIN_CFG_IO_VMC_QSPI		BIT(6)
-#define PIN_CFG_IO_VMC_ETH0		BIT(7)
-#define PIN_CFG_IO_VMC_ETH1		BIT(8)
-#define PIN_CFG_FILONOFF		BIT(9)
-#define PIN_CFG_FILNUM			BIT(10)
-#define PIN_CFG_FILCLKSEL		BIT(11)
-
-#define RZG2L_MPXED_PIN_FUNCS		(PIN_CFG_IOLH | \
+#define PIN_CFG_IOLH_A			BIT(0)
+#define PIN_CFG_IOLH_B			BIT(1)
+#define PIN_CFG_SR			BIT(2)
+#define PIN_CFG_IEN			BIT(3)
+#define PIN_CFG_PUPD			BIT(4)
+#define PIN_CFG_IO_VMC_SD0		BIT(5)
+#define PIN_CFG_IO_VMC_SD1		BIT(6)
+#define PIN_CFG_IO_VMC_QSPI		BIT(7)
+#define PIN_CFG_IO_VMC_ETH0		BIT(8)
+#define PIN_CFG_IO_VMC_ETH1		BIT(9)
+#define PIN_CFG_FILONOFF		BIT(10)
+#define PIN_CFG_FILNUM			BIT(11)
+#define PIN_CFG_FILCLKSEL		BIT(12)
+
+#define RZG2L_MPXED_PIN_FUNCS		(PIN_CFG_IOLH_A | \
 					 PIN_CFG_SR | \
 					 PIN_CFG_PUPD | \
 					 PIN_CFG_FILONOFF | \
@@ -86,6 +87,7 @@
 #define PMC(n)			(0x0200 + 0x10 + (n))
 #define PFC(n)			(0x0400 + 0x40 + (n) * 4)
 #define PIN(n)			(0x0800 + 0x10 + (n))
+#define IOLH(n)			(0x1000 + (n) * 8)
 #define IEN(n)			(0x1800 + (n) * 8)
 #define PWPR			(0x3014)
 #define SD_CH(n)		(0x3000 + (n) * 4)
@@ -101,6 +103,7 @@
 #define PVDD_MASK		0x01
 #define PFC_MASK		0x07
 #define IEN_MASK		0x01
+#define IOLH_MASK		0x03
 
 #define PM_INPUT		0x1
 #define PM_OUTPUT		0x2
@@ -138,6 +141,9 @@ struct rzg2l_pinctrl {
 	spinlock_t			lock;
 };
 
+static const unsigned int iolh_groupa_mA[] = { 2, 4, 8, 12 };
+static const unsigned int iolh_groupb_oi[] = { 100, 66, 50, 33 };
+
 static void rzg2l_pinctrl_set_pfc_mode(struct rzg2l_pinctrl *pctrl,
 				       u8 port, u8 pin, u8 func)
 {
@@ -532,6 +538,28 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 		break;
 	}
 
+	case PIN_CONFIG_DRIVE_STRENGTH: {
+		unsigned int index;
+
+		if (!(cfg & PIN_CFG_IOLH_A))
+			return -EINVAL;
+
+		index = rzg2l_read_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK);
+		arg = iolh_groupa_mA[index];
+		break;
+	}
+
+	case PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS: {
+		unsigned int index;
+
+		if (!(cfg & PIN_CFG_IOLH_B))
+			return -EINVAL;
+
+		index = rzg2l_read_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK);
+		arg = iolh_groupb_oi[index];
+		break;
+	}
+
 	default:
 		return -ENOTSUPP;
 	}
@@ -609,6 +637,43 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 			spin_unlock_irqrestore(&pctrl->lock, flags);
 			break;
 		}
+
+		case PIN_CONFIG_DRIVE_STRENGTH: {
+			unsigned int arg = pinconf_to_config_argument(_configs[i]);
+			unsigned int index;
+
+			if (!(cfg & PIN_CFG_IOLH_A))
+				return -EINVAL;
+
+			for (index = 0; index < ARRAY_SIZE(iolh_groupa_mA); index++) {
+				if (arg == iolh_groupa_mA[index])
+					break;
+			}
+			if (index >= ARRAY_SIZE(iolh_groupa_mA))
+				return -EINVAL;
+
+			rzg2l_rmw_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK, index);
+			break;
+		}
+
+		case PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS: {
+			unsigned int arg = pinconf_to_config_argument(_configs[i]);
+			unsigned int index;
+
+			if (!(cfg & PIN_CFG_IOLH_B))
+				return -EINVAL;
+
+			for (index = 0; index < ARRAY_SIZE(iolh_groupb_oi); index++) {
+				if (arg == iolh_groupb_oi[index])
+					break;
+			}
+			if (index >= ARRAY_SIZE(iolh_groupb_oi))
+				return -EINVAL;
+
+			rzg2l_rmw_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK, index);
+			break;
+		}
+
 		default:
 			return -EOPNOTSUPP;
 		}
@@ -935,75 +1000,75 @@ static  struct rzg2l_dedicated_configs rzg2l_dedicated_pins[] = {
 	{ "NMI", RZG2L_SINGLE_PIN_PACK(0x1, 0,
 	 (PIN_CFG_FILONOFF | PIN_CFG_FILNUM | PIN_CFG_FILCLKSEL)) },
 	{ "TMS/SWDIO", RZG2L_SINGLE_PIN_PACK(0x2, 0,
-	 (PIN_CFG_SR | PIN_CFG_IOLH | PIN_CFG_IEN)) },
+	 (PIN_CFG_SR | PIN_CFG_IOLH_A | PIN_CFG_IEN)) },
 	{ "TDO", RZG2L_SINGLE_PIN_PACK(0x3, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN)) },
+	 (PIN_CFG_IOLH_A | PIN_CFG_SR | PIN_CFG_IEN)) },
 	{ "AUDIO_CLK1", RZG2L_SINGLE_PIN_PACK(0x4, 0, PIN_CFG_IEN) },
 	{ "AUDIO_CLK2", RZG2L_SINGLE_PIN_PACK(0x4, 1, PIN_CFG_IEN) },
 	{ "SD0_CLK", RZG2L_SINGLE_PIN_PACK(0x6, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_CMD", RZG2L_SINGLE_PIN_PACK(0x6, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_RST#", RZG2L_SINGLE_PIN_PACK(0x6, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA0", RZG2L_SINGLE_PIN_PACK(0x7, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA1", RZG2L_SINGLE_PIN_PACK(0x7, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA2", RZG2L_SINGLE_PIN_PACK(0x7, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA3", RZG2L_SINGLE_PIN_PACK(0x7, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA4", RZG2L_SINGLE_PIN_PACK(0x7, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA5", RZG2L_SINGLE_PIN_PACK(0x7, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA6", RZG2L_SINGLE_PIN_PACK(0x7, 6,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA7", RZG2L_SINGLE_PIN_PACK(0x7, 7,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD1_CLK", RZG2L_SINGLE_PIN_PACK(0x8, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD1))},
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_CMD", RZG2L_SINGLE_PIN_PACK(0x8, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA0", RZG2L_SINGLE_PIN_PACK(0x9, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA1", RZG2L_SINGLE_PIN_PACK(0x9, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA2", RZG2L_SINGLE_PIN_PACK(0x9, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA3", RZG2L_SINGLE_PIN_PACK(0x9, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "QSPI0_SPCLK", RZG2L_SINGLE_PIN_PACK(0xa, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO0", RZG2L_SINGLE_PIN_PACK(0xa, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO1", RZG2L_SINGLE_PIN_PACK(0xa, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO2", RZG2L_SINGLE_PIN_PACK(0xa, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO3", RZG2L_SINGLE_PIN_PACK(0xa, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_SSL", RZG2L_SINGLE_PIN_PACK(0xa, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SPCLK", RZG2L_SINGLE_PIN_PACK(0xb, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO0", RZG2L_SINGLE_PIN_PACK(0xb, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO1", RZG2L_SINGLE_PIN_PACK(0xb, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO2", RZG2L_SINGLE_PIN_PACK(0xb, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO3", RZG2L_SINGLE_PIN_PACK(0xb, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR  | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR  | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SSL", RZG2L_SINGLE_PIN_PACK(0xb, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_RESET#", RZG2L_SINGLE_PIN_PACK(0xc, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_WP#", RZG2L_SINGLE_PIN_PACK(0xc, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_INT#", RZG2L_SINGLE_PIN_PACK(0xc, 2, (PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
-	{ "WDTOVF_PERROUT#", RZG2L_SINGLE_PIN_PACK(0xd, 0, (PIN_CFG_IOLH | PIN_CFG_SR)) },
+	{ "WDTOVF_PERROUT#", RZG2L_SINGLE_PIN_PACK(0xd, 0, (PIN_CFG_IOLH_A | PIN_CFG_SR)) },
 	{ "RIIC0_SDA", RZG2L_SINGLE_PIN_PACK(0xe, 0, PIN_CFG_IEN) },
 	{ "RIIC0_SCL", RZG2L_SINGLE_PIN_PACK(0xe, 1, PIN_CFG_IEN) },
 	{ "RIIC1_SDA", RZG2L_SINGLE_PIN_PACK(0xe, 2, PIN_CFG_IEN) },
-- 
2.17.1

[PATCH 5.10.y-cip 09/27] dt-bindings: memory: renesas,rpc-if: Miscellaneous improvements

[Lad Prabhakar]

From: Geert Uytterhoeven <geert+renesas@glider.be>

commit dbe60e5d7f15454ecc9c7d93dce6240fdaa70da9 upstream.

  - Fix rejection of legitimate flash subnodes containing multiple
    compatible values,
  - Add missing list of required properties.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d81b59a513c2a5204c8378b4a89cd07f97c46797.1627401508.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 .../memory-controllers/renesas,rpc-if.yaml      | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
index 6d6ba608fd22..ebc1052a5e9b 100644
--- a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
@@ -57,12 +57,23 @@ patternProperties:
     type: object
     properties:
       compatible:
-        enum:
-          - cfi-flash
-          - jedec,spi-nor
+        contains:
+          enum:
+            - cfi-flash
+            - jedec,spi-nor
 
 unevaluatedProperties: false
 
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - power-domains
+  - resets
+  - '#address-cells'
+  - '#size-cells'
+
 examples:
   - |
     #include <dt-bindings/clock/renesas-cpg-mssr.h>
-- 
2.17.1

[PATCH 5.10.y-cip 10/27] dt-bindings: memory: renesas,rpc-if: Add support for the R9A07G044

[Lad Prabhakar]

commit c271aa1f73515bcb35f977f30825832d41a2f504 upstream.

SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.

This patch adds a new compatible string to identify the RZ/G2L family
so that the timing values on RZ/G2L can be adjusted.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
[PL: Manually applied the changes.]
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 .../memory-controllers/renesas,rpc-if.yaml    | 43 ++++++++++++++-----
 1 file changed, 33 insertions(+), 10 deletions(-)

diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
index ebc1052a5e9b..e733b01abe13 100644
--- a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
@@ -24,12 +24,18 @@ allOf:
 
 properties:
   compatible:
-    items:
-      - enum:
-          - renesas,r8a77970-rpc-if       # R-Car V3M
-          - renesas,r8a77980-rpc-if       # R-Car V3H
-          - renesas,r8a77995-rpc-if       # R-Car D3
-      - const: renesas,rcar-gen3-rpc-if   # a generic R-Car gen3 device
+    oneOf:
+      - items:
+          - enum:
+              - renesas,r8a77970-rpc-if       # R-Car V3M
+              - renesas,r8a77980-rpc-if       # R-Car V3H
+              - renesas,r8a77995-rpc-if       # R-Car D3
+          - const: renesas,rcar-gen3-rpc-if   # a generic R-Car gen3 or RZ/G2{E,H,M,N} device
+
+      - items:
+          - enum:
+              - renesas,r9a07g044-rpc-if      # RZ/G2{L,LC}
+          - const: renesas,rzg2l-rpc-if       # RZ/G2L family
 
   reg:
     items:
@@ -43,8 +49,7 @@ properties:
       - const: dirmap
       - const: wbuf
 
-  clocks:
-    maxItems: 1
+  clocks: true
 
   power-domains:
     maxItems: 1
@@ -62,8 +67,6 @@ patternProperties:
             - cfi-flash
             - jedec,spi-nor
 
-unevaluatedProperties: false
-
 required:
   - compatible
   - reg
@@ -74,6 +77,26 @@ required:
   - '#address-cells'
   - '#size-cells'
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - renesas,rzg2l-rpc-if
+then:
+  properties:
+    clocks:
+      items:
+        - description: SPI Multi IO Register access clock (SPI_CLK2)
+        - description: SPI Multi IO Main clock (SPI_CLK).
+
+else:
+  properties:
+    clocks:
+      maxItems: 1
+
+unevaluatedProperties: false
+
 examples:
   - |
     #include <dt-bindings/clock/renesas-cpg-mssr.h>
-- 
2.17.1

[PATCH 5.10.y-cip 11/27] dt-bindings: memory: renesas,rpc-if: Add optional interrupts property

[Lad Prabhakar]

commit 4b5a231ff617d5cdc9e99f39a7268ad491400195 upstream.

For completeness add optional interrupts property.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 .../devicetree/bindings/memory-controllers/renesas,rpc-if.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
index e733b01abe13..3f694f627788 100644
--- a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
@@ -51,6 +51,9 @@ properties:
 
   clocks: true
 
+  interrupts:
+    maxItems: 1
+
   power-domains:
     maxItems: 1
 
-- 
2.17.1

[PATCH 5.10.y-cip 12/27] mtd: hyperbus: rpc-if: Check return value of rpcif_sw_init()

[Lad Prabhakar]

commit 981387ed06b96908223a607f5fba6efa42728fc2 upstream.

rpcif_sw_init() can fail so make sure we check the return value
of it and on error exit rpcif_hb_probe() callback with error code.

Fixes: 5de15b610f78 ("mtd: hyperbus: add Renesas RPC-IF driver")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/mtd/hyperbus/rpc-if.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/hyperbus/rpc-if.c b/drivers/mtd/hyperbus/rpc-if.c
index ecb050ba95cd..367b0d72bf62 100644
--- a/drivers/mtd/hyperbus/rpc-if.c
+++ b/drivers/mtd/hyperbus/rpc-if.c
@@ -124,7 +124,9 @@ static int rpcif_hb_probe(struct platform_device *pdev)
 	if (!hyperbus)
 		return -ENOMEM;
 
-	rpcif_sw_init(&hyperbus->rpc, pdev->dev.parent);
+	error = rpcif_sw_init(&hyperbus->rpc, pdev->dev.parent);
+	if (error)
+		return error;
 
 	platform_set_drvdata(pdev, hyperbus);
 
-- 
2.17.1

[PATCH 5.10.y-cip 13/27] memory: renesas-rpc-if: Return error in case devm_ioremap_resource() fails

[Lad Prabhakar]

commit 818fdfa89baac77a8df5a2c30f4fb798cc937aa0 upstream.

Make sure we return error in case devm_ioremap_resource() fails for dirmap
resource.

Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/memory/renesas-rpc-if.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/memory/renesas-rpc-if.c b/drivers/memory/renesas-rpc-if.c
index 77a011d5ff8c..861870223300 100644
--- a/drivers/memory/renesas-rpc-if.c
+++ b/drivers/memory/renesas-rpc-if.c
@@ -244,7 +244,7 @@ int rpcif_sw_init(struct rpcif *rpc, struct device *dev)
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dirmap");
 	rpc->dirmap = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(rpc->dirmap))
-		rpc->dirmap = NULL;
+		return PTR_ERR(rpc->dirmap);
 	rpc->size = resource_size(res);
 
 	rpc->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
-- 
2.17.1

[PATCH 5.10.y-cip 14/27] memory: renesas-rpc-if: Drop usage of RPCIF_DIRMAP_SIZE macro

[Lad Prabhakar]

commit 5da9b59b23d8112709034a07338e03dcc65fa11f upstream.

RPCIF_DIRMAP_SIZE may differ on various SoC's. Instead of using
RPCIF_DIRMAP_SIZE macro use resource size to get dirmap size
which is already part of struct rpcif.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/memory/renesas-rpc-if.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/memory/renesas-rpc-if.c b/drivers/memory/renesas-rpc-if.c
index 861870223300..140cb4e2b789 100644
--- a/drivers/memory/renesas-rpc-if.c
+++ b/drivers/memory/renesas-rpc-if.c
@@ -147,8 +147,6 @@
 #define RPCIF_PHYINT		0x0088	/* R/W */
 #define RPCIF_PHYINT_WPVAL	BIT(1)
 
-#define RPCIF_DIRMAP_SIZE	0x4000000
-
 static const struct regmap_range rpcif_volatile_ranges[] = {
 	regmap_reg_range(RPCIF_SMRDR0, RPCIF_SMRDR1),
 	regmap_reg_range(RPCIF_SMWDR0, RPCIF_SMWDR1),
@@ -547,8 +545,8 @@ EXPORT_SYMBOL(rpcif_manual_xfer);
 
 ssize_t rpcif_dirmap_read(struct rpcif *rpc, u64 offs, size_t len, void *buf)
 {
-	loff_t from = offs & (RPCIF_DIRMAP_SIZE - 1);
-	size_t size = RPCIF_DIRMAP_SIZE - from;
+	loff_t from = offs & (rpc->size - 1);
+	size_t size = rpc->size - from;
 
 	if (len > size)
 		len = size;
-- 
2.17.1

[PATCH 5.10.y-cip 15/27] memory: renesas-rpc-if: correct whitespace

[Lad Prabhakar]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

commit 8c84a7335e71de1f045247eb035d55712e13222a upstream.

Use spaces instead of tabs as word separator.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601160608.312446-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 include/memory/renesas-rpc-if.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/include/memory/renesas-rpc-if.h b/include/memory/renesas-rpc-if.h
index 2df18b7a35fa..77c694a19149 100644
--- a/include/memory/renesas-rpc-if.h
+++ b/include/memory/renesas-rpc-if.h
@@ -19,7 +19,7 @@ enum rpcif_data_dir {
 	RPCIF_DATA_OUT,
 };
 
-struct	rpcif_op {
+struct rpcif_op {
 	struct {
 		u8 buswidth;
 		u8 opcode;
@@ -57,7 +57,7 @@ struct	rpcif_op {
 	} data;
 };
 
-struct	rpcif {
+struct rpcif {
 	struct device *dev;
 	void __iomem *base;
 	void __iomem *dirmap;
@@ -77,7 +77,7 @@ struct	rpcif {
 	u32 ddr;		/* DRDRENR or SMDRENR */
 };
 
-int  rpcif_sw_init(struct rpcif *rpc, struct device *dev);
+int rpcif_sw_init(struct rpcif *rpc, struct device *dev);
 void rpcif_hw_init(struct rpcif *rpc, bool hyperflash);
 void rpcif_prepare(struct rpcif *rpc, const struct rpcif_op *op, u64 *offs,
 		   size_t *len);
-- 
2.17.1

[PATCH 5.10.y-cip 16/27] memory: renesas-rpc-if: Add support for RZ/G2L

[Lad Prabhakar]

commit b04cc0d912eb80d3c438b11d96ca847c3e77e8ab upstream.

SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.

This patch adds a new compatible string for the RZ/G2L family so
that the timing values on RZ/G2L can be adjusted.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211025205631.21151-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/memory/renesas-rpc-if.c | 72 ++++++++++++++++++++++++++++-----
 drivers/mtd/hyperbus/rpc-if.c   |  4 +-
 drivers/spi/spi-rpc-if.c        |  4 +-
 include/memory/renesas-rpc-if.h |  8 +++-
 4 files changed, 75 insertions(+), 13 deletions(-)

diff --git a/drivers/memory/renesas-rpc-if.c b/drivers/memory/renesas-rpc-if.c
index 140cb4e2b789..7e20853df4a2 100644
--- a/drivers/memory/renesas-rpc-if.c
+++ b/drivers/memory/renesas-rpc-if.c
@@ -12,6 +12,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/regmap.h>
 #include <linux/reset.h>
 
@@ -27,8 +28,8 @@
 #define RPCIF_CMNCR_MOIIO_HIZ	(RPCIF_CMNCR_MOIIO0(3) | \
 				 RPCIF_CMNCR_MOIIO1(3) | \
 				 RPCIF_CMNCR_MOIIO2(3) | RPCIF_CMNCR_MOIIO3(3))
-#define RPCIF_CMNCR_IO3FV(val)	(((val) & 0x3) << 14) /* undocumented */
-#define RPCIF_CMNCR_IO2FV(val)	(((val) & 0x3) << 12) /* undocumented */
+#define RPCIF_CMNCR_IO3FV(val)	(((val) & 0x3) << 14) /* documented for RZ/G2L */
+#define RPCIF_CMNCR_IO2FV(val)	(((val) & 0x3) << 12) /* documented for RZ/G2L */
 #define RPCIF_CMNCR_IO0FV(val)	(((val) & 0x3) << 8)
 #define RPCIF_CMNCR_IOFV_HIZ	(RPCIF_CMNCR_IO0FV(3) | RPCIF_CMNCR_IO2FV(3) | \
 				 RPCIF_CMNCR_IO3FV(3))
@@ -126,6 +127,9 @@
 #define RPCIF_SMDRENR_OPDRE	BIT(4)
 #define RPCIF_SMDRENR_SPIDRE	BIT(0)
 
+#define RPCIF_PHYADD		0x0070	/* R/W available on R-Car E3/D3/V3M and RZ/G2{E,L} */
+#define RPCIF_PHYWR		0x0074	/* R/W available on R-Car E3/D3/V3M and RZ/G2{E,L} */
+
 #define RPCIF_PHYCNT		0x007C	/* R/W */
 #define RPCIF_PHYCNT_CAL	BIT(31)
 #define RPCIF_PHYCNT_OCTA(v)	(((v) & 0x3) << 22)
@@ -133,10 +137,12 @@
 #define RPCIF_PHYCNT_OCT	BIT(20)
 #define RPCIF_PHYCNT_DDRCAL	BIT(19)
 #define RPCIF_PHYCNT_HS		BIT(18)
-#define RPCIF_PHYCNT_STRTIM(v)	(((v) & 0x7) << 15)
+#define RPCIF_PHYCNT_CKSEL(v)	(((v) & 0x3) << 16) /* valid only for RZ/G2L */
+#define RPCIF_PHYCNT_STRTIM(v)	(((v) & 0x7) << 15) /* valid for R-Car and RZ/G2{E,H,M,N} */
 #define RPCIF_PHYCNT_WBUF2	BIT(4)
 #define RPCIF_PHYCNT_WBUF	BIT(2)
 #define RPCIF_PHYCNT_PHYMEM(v)	(((v) & 0x3) << 0)
+#define RPCIF_PHYCNT_PHYMEM_MASK GENMASK(1, 0)
 
 #define RPCIF_PHYOFFSET1	0x0080	/* R/W */
 #define RPCIF_PHYOFFSET1_DDRTMG(v) (((v) & 0x3) << 28)
@@ -245,18 +251,46 @@ int rpcif_sw_init(struct rpcif *rpc, struct device *dev)
 		return PTR_ERR(rpc->dirmap);
 	rpc->size = resource_size(res);
 
+	rpc->type = (enum rpcif_type)of_device_get_match_data(dev);
 	rpc->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
 
 	return PTR_ERR_OR_ZERO(rpc->rstc);
 }
 EXPORT_SYMBOL(rpcif_sw_init);
 
-void rpcif_hw_init(struct rpcif *rpc, bool hyperflash)
+static void rpcif_rzg2l_timing_adjust_sdr(struct rpcif *rpc)
+{
+	u32 data;
+
+	regmap_write(rpc->regmap, RPCIF_PHYWR, 0xa5390000);
+	regmap_write(rpc->regmap, RPCIF_PHYADD, 0x80000000);
+	regmap_write(rpc->regmap, RPCIF_PHYWR, 0x00008080);
+	regmap_write(rpc->regmap, RPCIF_PHYADD, 0x80000022);
+	regmap_write(rpc->regmap, RPCIF_PHYWR, 0x00008080);
+	regmap_write(rpc->regmap, RPCIF_PHYADD, 0x80000024);
+
+	regmap_read(rpc->regmap, RPCIF_PHYCNT, &data);
+	regmap_write(rpc->regmap, RPCIF_PHYCNT, data | RPCIF_PHYCNT_CKSEL(3));
+	regmap_write(rpc->regmap, RPCIF_PHYWR, 0x00000030);
+	regmap_write(rpc->regmap, RPCIF_PHYADD, 0x80000032);
+}
+
+int rpcif_hw_init(struct rpcif *rpc, bool hyperflash)
 {
 	u32 dummy;
 
 	pm_runtime_get_sync(rpc->dev);
 
+	if (rpc->type == RPCIF_RZ_G2L) {
+		int ret;
+
+		ret = reset_control_reset(rpc->rstc);
+		if (ret)
+			return ret;
+		usleep_range(200, 300);
+		rpcif_rzg2l_timing_adjust_sdr(rpc);
+	}
+
 	/*
 	 * NOTE: The 0x260 are undocumented bits, but they must be set.
 	 *	 RPCIF_PHYCNT_STRTIM is strobe timing adjustment bits,
@@ -265,8 +299,15 @@ void rpcif_hw_init(struct rpcif *rpc, bool hyperflash)
 	 *	 On H3 ES1.x, the value should be 0, while on others,
 	 *	 the value should be 7.
 	 */
-	regmap_write(rpc->regmap, RPCIF_PHYCNT, RPCIF_PHYCNT_STRTIM(7) |
-		     RPCIF_PHYCNT_PHYMEM(hyperflash ? 3 : 0) | 0x260);
+	if (rpc->type == RPCIF_RCAR_GEN3) {
+		regmap_write(rpc->regmap, RPCIF_PHYCNT, RPCIF_PHYCNT_STRTIM(7) |
+			     RPCIF_PHYCNT_PHYMEM(hyperflash ? 3 : 0) | 0x260);
+	} else {
+		regmap_read(rpc->regmap, RPCIF_PHYCNT, &dummy);
+		dummy &= ~RPCIF_PHYCNT_PHYMEM_MASK;
+		dummy |= RPCIF_PHYCNT_PHYMEM(hyperflash ? 3 : 0) | 0x260;
+		regmap_write(rpc->regmap, RPCIF_PHYCNT, dummy);
+	}
 
 	/*
 	 * NOTE: The 0x1511144 are undocumented bits, but they must be set
@@ -283,9 +324,17 @@ void rpcif_hw_init(struct rpcif *rpc, bool hyperflash)
 		regmap_update_bits(rpc->regmap, RPCIF_PHYINT,
 				   RPCIF_PHYINT_WPVAL, 0);
 
-	regmap_write(rpc->regmap, RPCIF_CMNCR, RPCIF_CMNCR_SFDE |
-		     RPCIF_CMNCR_MOIIO_HIZ | RPCIF_CMNCR_IOFV_HIZ |
-		     RPCIF_CMNCR_BSZ(hyperflash ? 1 : 0));
+	if (rpc->type == RPCIF_RCAR_GEN3)
+		regmap_write(rpc->regmap, RPCIF_CMNCR, RPCIF_CMNCR_SFDE |
+			     RPCIF_CMNCR_MOIIO_HIZ | RPCIF_CMNCR_IOFV_HIZ |
+			     RPCIF_CMNCR_BSZ(hyperflash ? 1 : 0));
+	else
+		regmap_write(rpc->regmap, RPCIF_CMNCR, RPCIF_CMNCR_SFDE |
+			     RPCIF_CMNCR_MOIIO3(1) | RPCIF_CMNCR_MOIIO2(1) |
+			     RPCIF_CMNCR_MOIIO1(1) | RPCIF_CMNCR_MOIIO0(1) |
+			     RPCIF_CMNCR_IO3FV(2) | RPCIF_CMNCR_IO2FV(2) |
+			     RPCIF_CMNCR_IO0FV(2) | RPCIF_CMNCR_BSZ(hyperflash ? 1 : 0));
+
 	/* Set RCF after BSZ update */
 	regmap_write(rpc->regmap, RPCIF_DRCR, RPCIF_DRCR_RCF);
 	/* Dummy read according to spec */
@@ -296,6 +345,8 @@ void rpcif_hw_init(struct rpcif *rpc, bool hyperflash)
 	pm_runtime_put(rpc->dev);
 
 	rpc->bus_size = hyperflash ? 2 : 1;
+
+	return 0;
 }
 EXPORT_SYMBOL(rpcif_hw_init);
 
@@ -613,7 +664,8 @@ static int rpcif_remove(struct platform_device *pdev)
 }
 
 static const struct of_device_id rpcif_of_match[] = {
-	{ .compatible = "renesas,rcar-gen3-rpc-if", },
+	{ .compatible = "renesas,rcar-gen3-rpc-if", .data = (void *)RPCIF_RCAR_GEN3 },
+	{ .compatible = "renesas,rzg2l-rpc-if", .data = (void *)RPCIF_RZ_G2L },
 	{},
 };
 MODULE_DEVICE_TABLE(of, rpcif_of_match);
diff --git a/drivers/mtd/hyperbus/rpc-if.c b/drivers/mtd/hyperbus/rpc-if.c
index 367b0d72bf62..40bca89268c3 100644
--- a/drivers/mtd/hyperbus/rpc-if.c
+++ b/drivers/mtd/hyperbus/rpc-if.c
@@ -132,7 +132,9 @@ static int rpcif_hb_probe(struct platform_device *pdev)
 
 	rpcif_enable_rpm(&hyperbus->rpc);
 
-	rpcif_hw_init(&hyperbus->rpc, true);
+	error = rpcif_hw_init(&hyperbus->rpc, true);
+	if (error)
+		return error;
 
 	hyperbus->hbdev.map.size = hyperbus->rpc.size;
 	hyperbus->hbdev.map.virt = hyperbus->rpc.dirmap;
diff --git a/drivers/spi/spi-rpc-if.c b/drivers/spi/spi-rpc-if.c
index 727d7cf0a6ad..651d92028306 100644
--- a/drivers/spi/spi-rpc-if.c
+++ b/drivers/spi/spi-rpc-if.c
@@ -156,7 +156,9 @@ static int rpcif_spi_probe(struct platform_device *pdev)
 	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_TX_QUAD | SPI_RX_QUAD;
 	ctlr->flags = SPI_CONTROLLER_HALF_DUPLEX;
 
-	rpcif_hw_init(rpc, false);
+	error = rpcif_hw_init(rpc, false);
+	if (error)
+		return error;
 
 	error = spi_register_controller(ctlr);
 	if (error) {
diff --git a/include/memory/renesas-rpc-if.h b/include/memory/renesas-rpc-if.h
index 77c694a19149..7c93f5177532 100644
--- a/include/memory/renesas-rpc-if.h
+++ b/include/memory/renesas-rpc-if.h
@@ -57,6 +57,11 @@ struct rpcif_op {
 	} data;
 };
 
+enum rpcif_type {
+	RPCIF_RCAR_GEN3,
+	RPCIF_RZ_G2L,
+};
+
 struct rpcif {
 	struct device *dev;
 	void __iomem *base;
@@ -64,6 +69,7 @@ struct rpcif {
 	struct regmap *regmap;
 	struct reset_control *rstc;
 	size_t size;
+	enum rpcif_type type;
 	enum rpcif_data_dir dir;
 	u8 bus_size;
 	void *buffer;
@@ -78,7 +84,7 @@ struct rpcif {
 };
 
 int rpcif_sw_init(struct rpcif *rpc, struct device *dev);
-void rpcif_hw_init(struct rpcif *rpc, bool hyperflash);
+int rpcif_hw_init(struct rpcif *rpc, bool hyperflash);
 void rpcif_prepare(struct rpcif *rpc, const struct rpcif_op *op, u64 *offs,
 		   size_t *len);
 int rpcif_manual_xfer(struct rpcif *rpc);
-- 
2.17.1

[PATCH 5.10.y-cip 17/27] clk: renesas: r9a07g044: Add clock and reset entries for SPI Multi I/O Bus Controller

[Lad Prabhakar]

commit f294a0ea9d12a658ff326bbe0d64137659bc2fc9 upstream.

Add clock and reset entries for SPI Multi I/O Bus Controller.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210928130132.15022-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/clk/renesas/r9a07g044-cpg.c | 18 ++++++++++++++++++
 drivers/clk/renesas/rzg2l-cpg.h     |  3 +++
 2 files changed, 21 insertions(+)

diff --git a/drivers/clk/renesas/r9a07g044-cpg.c b/drivers/clk/renesas/r9a07g044-cpg.c
index 3c518b56c5a6..1e331cdb13a5 100644
--- a/drivers/clk/renesas/r9a07g044-cpg.c
+++ b/drivers/clk/renesas/r9a07g044-cpg.c
@@ -29,10 +29,14 @@ enum clk_ids {
 	CLK_PLL2_DIV16,
 	CLK_PLL2_DIV20,
 	CLK_PLL3,
+	CLK_PLL3_400,
+	CLK_PLL3_533,
 	CLK_PLL3_DIV2,
 	CLK_PLL3_DIV2_4,
 	CLK_PLL3_DIV2_4_2,
 	CLK_PLL3_DIV4,
+	CLK_SEL_PLL3_3,
+	CLK_DIV_PLL3_C,
 	CLK_PLL4,
 	CLK_PLL5,
 	CLK_PLL5_FOUT3,
@@ -56,6 +60,7 @@ static const struct clk_div_table dtable_1_32[] = {
 };
 
 /* Mux clock tables */
+static const char * const sel_pll3_3[] = { ".pll3_533", ".pll3_400" };
 static const char * const sel_pll6_2[]	= { ".pll6_250", ".pll5_250" };
 
 static const struct cpg_core_clk r9a07g044_core_clks[] __initconst = {
@@ -68,6 +73,8 @@ static const struct cpg_core_clk r9a07g044_core_clks[] __initconst = {
 	DEF_SAMPLL(".pll1", CLK_PLL1, CLK_EXTAL, PLL146_CONF(0)),
 	DEF_FIXED(".pll2", CLK_PLL2, CLK_EXTAL, 133, 2),
 	DEF_FIXED(".pll3", CLK_PLL3, CLK_EXTAL, 133, 2),
+	DEF_FIXED(".pll3_400", CLK_PLL3_400, CLK_PLL3, 1, 4),
+	DEF_FIXED(".pll3_533", CLK_PLL3_533, CLK_PLL3, 1, 3),
 
 	DEF_FIXED(".pll5", CLK_PLL5, CLK_EXTAL, 125, 1),
 	DEF_FIXED(".pll5_fout3", CLK_PLL5_FOUT3, CLK_PLL5, 1, 6),
@@ -82,6 +89,10 @@ static const struct cpg_core_clk r9a07g044_core_clks[] __initconst = {
 	DEF_FIXED(".pll3_div2_4", CLK_PLL3_DIV2_4, CLK_PLL3_DIV2, 1, 4),
 	DEF_FIXED(".pll3_div2_4_2", CLK_PLL3_DIV2_4_2, CLK_PLL3_DIV2_4, 1, 2),
 	DEF_FIXED(".pll3_div4", CLK_PLL3_DIV4, CLK_PLL3, 1, 4),
+	DEF_MUX(".sel_pll3_3", CLK_SEL_PLL3_3, SEL_PLL3_3,
+		sel_pll3_3, ARRAY_SIZE(sel_pll3_3), 0, CLK_MUX_READ_ONLY),
+	DEF_DIV("divpl3c", CLK_DIV_PLL3_C, CLK_SEL_PLL3_3,
+		DIVPL3C, dtable_1_32, CLK_DIVIDER_HIWORD_MASK),
 
 	DEF_FIXED(".pll5_250", CLK_PLL5_250, CLK_PLL5_FOUT3, 1, 2),
 	DEF_FIXED(".pll6_250", CLK_PLL6_250, CLK_PLL6, 1, 2),
@@ -101,6 +112,8 @@ static const struct cpg_core_clk r9a07g044_core_clks[] __initconst = {
 	DEF_FIXED("ZT", R9A07G044_CLK_ZT, CLK_PLL3_DIV2_4_2, 1, 1),
 	DEF_MUX("HP", R9A07G044_CLK_HP, SEL_PLL6_2,
 		sel_pll6_2, ARRAY_SIZE(sel_pll6_2), 0, CLK_MUX_HIWORD_MASK),
+	DEF_FIXED("SPI0", R9A07G044_CLK_SPI0, CLK_DIV_PLL3_C, 1, 2),
+	DEF_FIXED("SPI1", R9A07G044_CLK_SPI1, CLK_DIV_PLL3_C, 1, 4),
 };
 
 static struct rzg2l_mod_clk r9a07g044_mod_clks[] = {
@@ -114,6 +127,10 @@ static struct rzg2l_mod_clk r9a07g044_mod_clks[] = {
 				0x52c, 0),
 	DEF_MOD("dmac_pclk",	R9A07G044_DMAC_PCLK, CLK_P1_DIV2,
 				0x52c, 1),
+	DEF_MOD("spi_clk2",	R9A07G044_SPI_CLK2, R9A07G044_CLK_SPI1,
+				0x550, 0),
+	DEF_MOD("spi_clk",	R9A07G044_SPI_CLK, R9A07G044_CLK_SPI0,
+				0x550, 1),
 	DEF_MOD("ssi0_pclk",	R9A07G044_SSI0_PCLK2, R9A07G044_CLK_P0,
 				0x570, 0),
 	DEF_MOD("ssi0_sfr",	R9A07G044_SSI0_PCLK_SFR, R9A07G044_CLK_P0,
@@ -182,6 +199,7 @@ static struct rzg2l_reset r9a07g044_resets[] = {
 	DEF_RST(R9A07G044_IA55_RESETN, 0x818, 0),
 	DEF_RST(R9A07G044_DMAC_ARESETN, 0x82c, 0),
 	DEF_RST(R9A07G044_DMAC_RST_ASYNC, 0x82c, 1),
+	DEF_RST(R9A07G044_SPI_RST, 0x850, 0),
 	DEF_RST(R9A07G044_SSI0_RST_M2_REG, 0x870, 0),
 	DEF_RST(R9A07G044_SSI1_RST_M2_REG, 0x870, 1),
 	DEF_RST(R9A07G044_SSI2_RST_M2_REG, 0x870, 2),
diff --git a/drivers/clk/renesas/rzg2l-cpg.h b/drivers/clk/renesas/rzg2l-cpg.h
index 191c403aa52f..dc5b65a4029e 100644
--- a/drivers/clk/renesas/rzg2l-cpg.h
+++ b/drivers/clk/renesas/rzg2l-cpg.h
@@ -11,6 +11,7 @@
 
 #define CPG_PL2_DDIV		(0x204)
 #define CPG_PL3A_DDIV		(0x208)
+#define CPG_PL3_SSEL		(0x408)
 #define CPG_PL6_ETH_SSEL	(0x418)
 
 /* n = 0/1/2 for PLL1/4/6 */
@@ -24,10 +25,12 @@
 #define DIVPL2A		DDIV_PACK(CPG_PL2_DDIV, 0, 3)
 #define DIVPL3A		DDIV_PACK(CPG_PL3A_DDIV, 0, 3)
 #define DIVPL3B		DDIV_PACK(CPG_PL3A_DDIV, 4, 3)
+#define DIVPL3C		DDIV_PACK(CPG_PL3A_DDIV, 8, 3)
 
 #define SEL_PLL_PACK(offset, bitpos, size) \
 		(((offset) << 20) | ((bitpos) << 12) | ((size) << 8))
 
+#define SEL_PLL3_3	SEL_PLL_PACK(CPG_PL3_SSEL, 8, 1)
 #define SEL_PLL6_2	SEL_PLL_PACK(CPG_PL6_ETH_SSEL, 0, 1)
 
 /**
-- 
2.17.1

[PATCH 5.10.y-cip 18/27] arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node

[Lad Prabhakar]

commit 9223cb663e9f3f1031f5ef9c6e398447e40338f6 upstream.

Add SPI Multi I/O Bus controller node to R9A07G044 (RZ/G2L) SoC DTSI.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210928155852.32569-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 arch/arm64/boot/dts/renesas/r9a07g044.dtsi | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
index a88d84b95034..2e443f6805bd 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -260,6 +260,23 @@
 			};
 		};
 
+		sbc: spi@10060000 {
+			compatible = "renesas,r9a07g044-rpc-if",
+				     "renesas,rzg2l-rpc-if";
+			reg = <0 0x10060000 0 0x10000>,
+			      <0 0x20000000 0 0x10000000>,
+			      <0 0x10070000 0 0x10000>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_SPI_CLK2>,
+				 <&cpg CPG_MOD R9A07G044_SPI_CLK>;
+			resets = <&cpg R9A07G044_SPI_RST>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		cpg: clock-controller@11010000 {
 			compatible = "renesas,r9a07g044-cpg";
 			reg = <0 0x11010000 0 0x10000>;
-- 
2.17.1

[PATCH 5.10.y-cip 19/27] arm64: dts: renesas: rzg2l-smarc-som: Enable serial NOR flash

[Lad Prabhakar]

commit c81bd70f47cef36f88074d119e6e49cf92707fdb upstream.

Enable mt25qu512a flash connected to QSPI0.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211121234906.9602-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[PL: Manually applied the changes.]
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 .../boot/dts/renesas/rzg2l-smarc-som.dtsi     | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
index 1fd961066236..9804ca0fd528 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
@@ -129,4 +129,44 @@
 			 <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
 			 <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */
 	};
+
+	qspi0_pins: qspi0 {
+		qspi0-data {
+			pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3";
+			power-source = <1800>;
+		};
+
+		qspi0-ctrl {
+			pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#";
+			power-source = <1800>;
+		};
+	};
+};
+
+&sbc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "micron,mt25qu512a", "jedec,spi-nor";
+		reg = <0>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				reg = <0x00000000 0x2000000>;
+				read-only;
+			};
+			user@2000000 {
+				reg = <0x2000000 0x2000000>;
+			};
+		};
+	};
 };
-- 
2.17.1

[PATCH 5.10.y-cip 20/27] clk: renesas: r9a07g044: Add clock and reset entry for SCI1

[Lad Prabhakar]

commit a0d2a2c6736c849463b424a7203f5e0e40949c03 upstream.

Add clock and reset entry for SCI1 interface.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211103160537.32253-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/clk/renesas/r9a07g044-cpg.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/clk/renesas/r9a07g044-cpg.c b/drivers/clk/renesas/r9a07g044-cpg.c
index 1e331cdb13a5..6c5204981dfb 100644
--- a/drivers/clk/renesas/r9a07g044-cpg.c
+++ b/drivers/clk/renesas/r9a07g044-cpg.c
@@ -183,6 +183,8 @@ static struct rzg2l_mod_clk r9a07g044_mod_clks[] = {
 				0x584, 4),
 	DEF_MOD("sci0",		R9A07G044_SCI0_CLKP, R9A07G044_CLK_P0,
 				0x588, 0),
+	DEF_MOD("sci1",		R9A07G044_SCI1_CLKP, R9A07G044_CLK_P0,
+				0x588, 1),
 	DEF_MOD("canfd",	R9A07G044_CANFD_PCLK, R9A07G044_CLK_P0,
 				0x594, 0),
 	DEF_MOD("gpio",		R9A07G044_GPIO_HCLK, R9A07G044_OSCCLK,
@@ -220,6 +222,7 @@ static struct rzg2l_reset r9a07g044_resets[] = {
 	DEF_RST(R9A07G044_SCIF3_RST_SYSTEM_N, 0x884, 3),
 	DEF_RST(R9A07G044_SCIF4_RST_SYSTEM_N, 0x884, 4),
 	DEF_RST(R9A07G044_SCI0_RST, 0x888, 0),
+	DEF_RST(R9A07G044_SCI1_RST, 0x888, 1),
 	DEF_RST(R9A07G044_CANFD_RSTP_N, 0x894, 0),
 	DEF_RST(R9A07G044_CANFD_RSTC_N, 0x894, 1),
 	DEF_RST(R9A07G044_GPIO_RSTN, 0x898, 0),
-- 
2.17.1

[PATCH 5.10.y-cip 21/27] dt-bindings: serial: renesas,scif: Make resets as a required property

[Lad Prabhakar]

commit 0836150c26c4028be9bd77c9a3dc3e3493542815 upstream.

Make "resets" as required property for RZ/G2L. On RZ/G2L the devices
should be explicitly pulled out of reset for this reason make "resets"
as required property.

Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 Documentation/devicetree/bindings/serial/renesas,scif.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/serial/renesas,scif.yaml b/Documentation/devicetree/bindings/serial/renesas,scif.yaml
index 7fa8cb0a7769..701cb4936f3c 100644
--- a/Documentation/devicetree/bindings/serial/renesas,scif.yaml
+++ b/Documentation/devicetree/bindings/serial/renesas,scif.yaml
@@ -150,6 +150,7 @@ if:
         enum:
           - renesas,rcar-gen2-scif
           - renesas,rcar-gen3-scif
+          - renesas,scif-r9a07g044
 then:
   required:
     - resets
-- 
2.17.1

[PATCH 5.10.y-cip 22/27] dt-bindings: serial: renesas,sci: Document RZ/G2L SoC

[Lad Prabhakar]

commit e1c0fc101340716fc1786b89f627425ecc6e5420 upstream.

Add SCI binding documentation for Renesas RZ/G2L SoC.

Also update the example node with RZ/G2L SCI0 node.

Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 .../bindings/serial/renesas,sci.yaml          | 46 ++++++++++++++++---
 1 file changed, 40 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/serial/renesas,sci.yaml b/Documentation/devicetree/bindings/serial/renesas,sci.yaml
index 22ed2f0b1dc3..f00b1d38e9a5 100644
--- a/Documentation/devicetree/bindings/serial/renesas,sci.yaml
+++ b/Documentation/devicetree/bindings/serial/renesas,sci.yaml
@@ -14,7 +14,14 @@ allOf:
 
 properties:
   compatible:
-    const: renesas,sci
+    oneOf:
+      - items:
+          - enum:
+              - renesas,r9a07g044-sci     # RZ/G2{L,LC}
+          - const: renesas,sci            # generic SCI compatible UART
+
+      - items:
+          - const: renesas,sci            # generic SCI compatible UART
 
   reg:
     maxItems: 1
@@ -54,18 +61,45 @@ required:
   - clocks
   - clock-names
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - renesas,r9a07g044-sci
+then:
+  properties:
+    resets:
+      maxItems: 1
+
+    power-domains:
+      maxItems: 1
+
+  required:
+    - resets
+    - power-domains
+
 unevaluatedProperties: false
 
 examples:
   - |
+    #include <dt-bindings/clock/r9a07g044-cpg.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
     aliases {
             serial0 = &sci0;
     };
 
-    sci0: serial@ffff78 {
-            compatible = "renesas,sci";
-            reg = <0xffff78 8>;
-            interrupts = <88 0>, <89 0>, <90 0>, <91 0>;
-            clocks = <&fclk>;
+    sci0: serial@1004d000 {
+            compatible = "renesas,r9a07g044-sci", "renesas,sci";
+            reg = <0x1004d000 0x400>;
+            interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "eri", "rxi", "txi", "tei";
+            clocks = <&cpg CPG_MOD R9A07G044_SCI0_CLKP>;
             clock-names = "fck";
+            power-domains = <&cpg>;
+            resets = <&cpg R9A07G044_SCI0_RST>;
     };
-- 
2.17.1

[PATCH 5.10.y-cip 23/27] serial: sh-sci: Add support to deassert/assert reset line

[Lad Prabhakar]

commit 862f72187a41008df2cce3f8e97f57070cbc7060 upstream.

On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.

This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.

Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.

Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 drivers/tty/serial/sh-sci.c | 39 ++++++++++++++++++++++++++++++-------
 1 file changed, 32 insertions(+), 7 deletions(-)

diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index c3fd49480ad3..517aff5f76da 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -37,6 +37,7 @@
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/reset.h>
 #include <linux/scatterlist.h>
 #include <linux/serial.h>
 #include <linux/serial_sci.h>
@@ -3235,23 +3236,47 @@ static const struct of_device_id of_sci_match[] = {
 };
 MODULE_DEVICE_TABLE(of, of_sci_match);
 
+static void sci_reset_control_assert(void *data)
+{
+	reset_control_assert(data);
+}
+
 static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev,
 					  unsigned int *dev_id)
 {
 	struct device_node *np = pdev->dev.of_node;
+	struct reset_control *rstc;
 	struct plat_sci_port *p;
 	struct sci_port *sp;
 	const void *data;
-	int id;
+	int id, ret;
 
 	if (!IS_ENABLED(CONFIG_OF) || !np)
-		return NULL;
+		return ERR_PTR(-EINVAL);
 
 	data = of_device_get_match_data(&pdev->dev);
 
+	rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(rstc))
+		return ERR_PTR(dev_err_probe(&pdev->dev, PTR_ERR(rstc),
+					     "failed to get reset ctrl\n"));
+
+	ret = reset_control_deassert(rstc);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to deassert reset %d\n", ret);
+		return ERR_PTR(ret);
+	}
+
+	ret = devm_add_action_or_reset(&pdev->dev, sci_reset_control_assert, rstc);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register assert devm action, %d\n",
+			ret);
+		return ERR_PTR(ret);
+	}
+
 	p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
 	if (!p)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	/* Get the line number from the aliases node. */
 	id = of_alias_get_id(np, "serial");
@@ -3259,11 +3284,11 @@ static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev,
 		id = ffz(sci_ports_in_use);
 	if (id < 0) {
 		dev_err(&pdev->dev, "failed to get alias id (%d)\n", id);
-		return NULL;
+		return ERR_PTR(-EINVAL);
 	}
 	if (id >= ARRAY_SIZE(sci_ports)) {
 		dev_err(&pdev->dev, "serial%d out of range\n", id);
-		return NULL;
+		return ERR_PTR(-EINVAL);
 	}
 
 	sp = &sci_ports[id];
@@ -3350,8 +3375,8 @@ static int sci_probe(struct platform_device *dev)
 
 	if (dev->dev.of_node) {
 		p = sci_parse_dt(dev, &dev_id);
-		if (p == NULL)
-			return -EINVAL;
+		if (IS_ERR(p))
+			return PTR_ERR(p);
 	} else {
 		p = dev->dev.platform_data;
 		if (p == NULL) {
-- 
2.17.1

[PATCH 5.10.y-cip 24/27] arm64: dts: renesas: r9a07g044: Add SCIF[1-4] nodes

[Lad Prabhakar]

commit 68f8eb19c18a377181622e58c1fd2ca0f5c0d15d upstream.

Add SCIF[1-4] nodes to r9a07g044 (RZ/G2L) SoC DTSI.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211103195600.23964-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 arch/arm64/boot/dts/renesas/r9a07g044.dtsi | 72 ++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
index 2e443f6805bd..52a475c298f0 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -96,6 +96,78 @@
 			status = "disabled";
 		};
 
+		scif1: serial@1004bc00 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004bc00 0 0x400>;
+			interrupts = <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF1_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF1_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif2: serial@1004c000 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004c000 0 0x400>;
+			interrupts = <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF2_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF2_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif3: serial@1004c400 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004c400 0 0x400>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF3_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF3_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif4: serial@1004c800 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004c800 0 0x400>;
+			interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF4_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF4_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
 		canfd: can@10050000 {
 			compatible = "renesas,r9a07g044-canfd", "renesas,rzg2l-canfd";
 			reg = <0 0x10050000 0 0x8000>;
-- 
2.17.1

[PATCH 5.10.y-cip 25/27] arm64: dts: renesas: rzg2l-smarc: Enable SCIF2 on carrier board

[Lad Prabhakar]

commit 5a8aa63c9bca800e6049d90422abe5404227a703 upstream.

SCIF2 interface is available on PMOD1 connector (CN7) on carrier board,
This patch adds pinmux and scif2 node to carrier board dtsi file.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211103195600.23964-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[PL: Manually applied the changes.]
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi | 28 ++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
index a33594575fc4..70aca5d0306d 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
@@ -8,9 +8,13 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
+/* comment the #define statement to disable SCIF2 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0	1
+
 / {
 	aliases {
 		serial0 = &scif0;
+		serial1 = &scif2;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c3 = &i2c3;
@@ -138,6 +142,13 @@
 			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */
 	};
 
+	scif2_pins: scif2 {
+		pinmux = <RZG2L_PORT_PINMUX(48, 0, 1)>, /* TxD */
+			 <RZG2L_PORT_PINMUX(48, 1, 1)>, /* RxD */
+			 <RZG2L_PORT_PINMUX(48, 3, 1)>, /* CTS# */
+			 <RZG2L_PORT_PINMUX(48, 4, 1)>; /* RTS# */
+	};
+
 	usb0_pins: usb0 {
 		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
 			 <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
@@ -156,6 +167,23 @@
 	status = "okay";
 };
 
+/*
+ * To enable SCIF2 (SER0) on PMOD1 (CN7)
+ * SW1 should be at position 2->3 so that SER0_CTS# line is activated
+ * SW2 should be at position 2->3 so that SER0_TX line is activated
+ * SW3 should be at position 2->3 so that SER0_RX line is activated
+ * SW4 should be at position 2->3 so that SER0_RTS# line is activated
+ */
+#if PMOD1_SER0
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+#endif
+
 &usb2_phy0 {
 	pinctrl-0 = <&usb0_pins>;
 	pinctrl-names = "default";
-- 
2.17.1

[PATCH 5.10.y-cip 26/27] arm64: dts: renesas: r9a07g044: Add SCI[0-1] nodes

[Lad Prabhakar]

commit f9a2adcc9e908907129c18518d4ea6195c44bf00 upstream.

Add SCI[0-1] nodes to r9a07g044 (RZ/G2L) SoC DTSI.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211109123110.8543-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 arch/arm64/boot/dts/renesas/r9a07g044.dtsi | 30 ++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
index 52a475c298f0..7efe2e86b417 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -168,6 +168,36 @@
 			status = "disabled";
 		};
 
+		sci0: serial@1004d000 {
+			compatible = "renesas,r9a07g044-sci", "renesas,sci";
+			reg = <0 0x1004d000 0 0x400>;
+			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCI0_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCI0_RST>;
+			status = "disabled";
+		};
+
+		sci1: serial@1004d400 {
+			compatible = "renesas,r9a07g044-sci", "renesas,sci";
+			reg = <0 0x1004d400 0 0x400>;
+			interrupts = <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCI1_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCI1_RST>;
+			status = "disabled";
+		};
+
 		canfd: can@10050000 {
 			compatible = "renesas,r9a07g044-canfd", "renesas,rzg2l-canfd";
 			reg = <0 0x10050000 0 0x8000>;
-- 
2.17.1

[PATCH 5.10.y-cip 27/27] arm64: dts: renesas: r9a07g044: Sort psci node

[Lad Prabhakar]

From: Biju Das <biju.das.jz@bp.renesas.com>

commit 5fcf8b0656cf842ae642298c2874ea6148d0129d upstream.

Sort psci node alphabetically.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 arch/arm64/boot/dts/renesas/r9a07g044.dtsi | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
index 7efe2e86b417..ebe155ccd721 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -28,11 +28,6 @@
 		clock-frequency = <0>;
 	};
 
-	psci {
-		compatible = "arm,psci-1.0", "arm,psci-0.2";
-		method = "smc";
-	};
-
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -71,6 +66,11 @@
 		};
 	};
 
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
 	soc: soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
-- 
2.17.1

RE: [PATCH 5.10.y-cip 12/27] mtd: hyperbus: rpc-if: Check return value of rpcif_sw_init()

[nobuhiro1.iwamatsu]

Hi,

> -----Original Message-----
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Sent: Monday, January 31, 2022 9:19 PM
> To: cip-dev@lists.cip-project.org; iwamatsu nobuhiro(岩松 信洋 □ＳＷＣ◯Ａ
> ＣＴ) <nobuhiro1.iwamatsu@toshiba.co.jp>; Pavel Machek
> <pavel@denx.de>
> Cc: Biju Das <biju.das.jz@bp.renesas.com>
> Subject: [PATCH 5.10.y-cip 12/27] mtd: hyperbus: rpc-if: Check return value of
> rpcif_sw_init()
> 
> commit 981387ed06b96908223a607f5fba6efa42728fc2 upstream.
> 
> rpcif_sw_init() can fail so make sure we check the return value of it and on error
> exit rpcif_hb_probe() callback with error code.
> 
> Fixes: 5de15b610f78 ("mtd: hyperbus: add Renesas RPC-IF driver")
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Link:
> https://lore.kernel.org/r/20211025205631.21151-5-prabhakar.mahadev-lad.rj
> @bp.renesas.com
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
>  drivers/mtd/hyperbus/rpc-if.c | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)


> 
> diff --git a/drivers/mtd/hyperbus/rpc-if.c b/drivers/mtd/hyperbus/rpc-if.c
> index ecb050ba95cd..367b0d72bf62 100644
> --- a/drivers/mtd/hyperbus/rpc-if.c
> +++ b/drivers/mtd/hyperbus/rpc-if.c
> @@ -124,7 +124,9 @@ static int rpcif_hb_probe(struct platform_device *pdev)
>  	if (!hyperbus)
>  		return -ENOMEM;
> 
> -	rpcif_sw_init(&hyperbus->rpc, pdev->dev.parent);
> +	error = rpcif_sw_init(&hyperbus->rpc, pdev->dev.parent);
> +	if (error)
> +		return error;
> 
>  	platform_set_drvdata(pdev, hyperbus);
> 
> --
> 2.17.1

I think we can fix this with stable tree.

Best regards,
  Nobuhiro

RE: [PATCH 5.10.y-cip 13/27] memory: renesas-rpc-if: Return error in case devm_ioremap_resource() fails

[nobuhiro1.iwamatsu]

Hi,

> -----Original Message-----
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Sent: Monday, January 31, 2022 9:19 PM
> To: cip-dev@lists.cip-project.org; iwamatsu nobuhiro(岩松 信洋 □ＳＷＣ◯Ａ
> ＣＴ) <nobuhiro1.iwamatsu@toshiba.co.jp>; Pavel Machek
> <pavel@denx.de>
> Cc: Biju Das <biju.das.jz@bp.renesas.com>
> Subject: [PATCH 5.10.y-cip 13/27] memory: renesas-rpc-if: Return error in
> case devm_ioremap_resource() fails
> 
> commit 818fdfa89baac77a8df5a2c30f4fb798cc937aa0 upstream.
> 
> Make sure we return error in case devm_ioremap_resource() fails for dirmap
> resource.
> 
> Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Link:
> https://lore.kernel.org/r/20211025205631.21151-6-prabhakar.mahadev-lad.rj
> @bp.renesas.com
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
>  drivers/memory/renesas-rpc-if.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/memory/renesas-rpc-if.c
> b/drivers/memory/renesas-rpc-if.c index 77a011d5ff8c..861870223300 100644
> --- a/drivers/memory/renesas-rpc-if.c
> +++ b/drivers/memory/renesas-rpc-if.c
> @@ -244,7 +244,7 @@ int rpcif_sw_init(struct rpcif *rpc, struct device *dev)
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> "dirmap");
>  	rpc->dirmap = devm_ioremap_resource(&pdev->dev, res);
>  	if (IS_ERR(rpc->dirmap))
> -		rpc->dirmap = NULL;
> +		return PTR_ERR(rpc->dirmap);
>  	rpc->size = resource_size(res);
> 
>  	rpc->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
> --
> 2.17.1

I think we can fix this with stable tree.

Best regards,
  Nobuhiro

Re: [PATCH 5.10.y-cip 05/27] pinctrl: renesas: rzg2l: Add helper functions to read/write pin config

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1723 bytes --]

Hi!

> commit d1189991c823b50990291c8157b56fb141c47155 upstream.
> 
> Add helper functions to read/read modify write pin config.
> 
> Switch to use helper functions for pins supporting PIN_CONFIG_INPUT_ENABLE
> capabilities.

Along with refactoring code, this also removes locking from the
reads. Which is okay AFAICT, but note in changelog would not hurt.

Best regards,
								Pavel

> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -424,6 +424,39 @@ static int rzg2l_dt_node_to_map(struct pinctrl_dev *pctldev,
>  	return ret;
>  }
>  
> +static u32 rzg2l_read_pin_config(struct rzg2l_pinctrl *pctrl, u32 offset,
> +				 u8 bit, u32 mask)
> +{
> +	void __iomem *addr = pctrl->base + offset;
> +
> +	/* handle _L/_H for 32-bit register read/write */
> +	if (bit >= 4) {
> +		bit -= 4;
> +		addr += 4;
> +	}
> +
> +	return (readl(addr) >> (bit * 8)) & mask;
> +}
> +
> @@ -452,17 +485,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>  	case PIN_CONFIG_INPUT_ENABLE:
>  		if (!(cfg & PIN_CFG_IEN))
>  			return -EINVAL;
> -		spin_lock_irqsave(&pctrl->lock, flags);
> -		/* handle _L/_H for 32-bit register read/write */
> -		addr = pctrl->base + IEN(port_offset);
> -		if (bit >= 4) {
> -			bit -= 4;
> -			addr += 4;
> -		}
> -
> -		reg = readl(addr) & (IEN_MASK << (bit * 8));
> -		arg = (reg >> (bit * 8)) & 0x1;
> -		spin_unlock_irqrestore(&pctrl->lock, flags);
> +		arg = rzg2l_read_pin_config(pctrl, IEN(port_offset), bit, IEN_MASK);
>  		break;
>  
>  	case PIN_CONFIG_POWER_SOURCE: {

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 5.10.y-cip 16/27] memory: renesas-rpc-if: Add support for RZ/G2L

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 914 bytes --]

Hi!

> commit b04cc0d912eb80d3c438b11d96ca847c3e77e8ab upstream.
> 
> SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
> the RPC-IF interface found on R-Car Gen3 SoC's.
> 
> This patch adds a new compatible string for the RZ/G2L family so
> that the timing values on RZ/G2L can be adjusted.

> +int rpcif_hw_init(struct rpcif *rpc, bool hyperflash)
>  {
>  	u32 dummy;
>  
>  	pm_runtime_get_sync(rpc->dev);

> +	if (rpc->type == RPCIF_RZ_G2L) {
> +		int ret;
> +
> +		ret = reset_control_reset(rpc->rstc);
> +		if (ret)
> +			return ret;
> +		usleep_range(200, 300);
> +		rpcif_rzg2l_timing_adjust_sdr(rpc);
> +	}

Should pm_runtime_put() be called before returning failure to the
caller?

Best regards,
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 5.10.y-cip 19/27] arm64: dts: renesas: rzg2l-smarc-som: Enable serial NOR flash

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 773 bytes --]

Hi!

> commit c81bd70f47cef36f88074d119e6e49cf92707fdb upstream.
> 
> Enable mt25qu512a flash connected to QSPI0.
> 

> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			boot@0 {
> +				reg = <0x00000000 0x2000000>;
> +				read-only;
> +			};
> +			user@2000000 {
> +				reg = <0x2000000 0x2000000>;
> +			};

This confused me for a while. Some of hex numbers are 7 digits, some
are 8. Making it consistent at 8 digits would be good. (Or maybe 
using 0x0 so it is clear we are not aiming for 8 digits).

Best regards,
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 5.10.y-cip 25/27] arm64: dts: renesas: rzg2l-smarc: Enable SCIF2 on carrier board

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1397 bytes --]

Hi!

> commit 5a8aa63c9bca800e6049d90422abe5404227a703 upstream.
> 
> SCIF2 interface is available on PMOD1 connector (CN7) on carrier board,
> This patch adds pinmux and scif2 node to carrier board dtsi file.


> +++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
> @@ -8,9 +8,13 @@
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
>  
> +/* comment the #define statement to disable SCIF2 (SER0) on PMOD1 (CN7) */
> +#define PMOD1_SER0	1
> +

AFAICT this needs to be set to 0, not commented out.


> @@ -156,6 +167,23 @@
>  	status = "okay";
>  };
>  
> +/*
> + * To enable SCIF2 (SER0) on PMOD1 (CN7)
> + * SW1 should be at position 2->3 so that SER0_CTS# line is activated
> + * SW2 should be at position 2->3 so that SER0_TX line is activated
> + * SW3 should be at position 2->3 so that SER0_RX line is activated
> + * SW4 should be at position 2->3 so that SER0_RTS# line is activated
> + */
> +#if PMOD1_SER0
> +&scif2 {
> +	pinctrl-0 = <&scif2_pins>;
> +	pinctrl-names = "default";
> +
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +#endif
> +
>  &usb2_phy0 {
>  	pinctrl-0 = <&usb0_pins>;
>  	pinctrl-names = "default";

Best regards,
								Pavel

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 5.10.y-cip 16/27] memory: renesas-rpc-if: Add support for RZ/G2L

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1480 bytes --]

Hi!
> commit b04cc0d912eb80d3c438b11d96ca847c3e77e8ab upstream.
> 
> SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
> the RPC-IF interface found on R-Car Gen3 SoC's.
> 
> This patch adds a new compatible string for the RZ/G2L family so
> that the timing values on RZ/G2L can be adjusted.


> index 367b0d72bf62..40bca89268c3 100644
> --- a/drivers/mtd/hyperbus/rpc-if.c
> +++ b/drivers/mtd/hyperbus/rpc-if.c
> @@ -132,7 +132,9 @@ static int rpcif_hb_probe(struct platform_device *pdev)
>  
>  	rpcif_enable_rpm(&hyperbus->rpc);
>  
> -	rpcif_hw_init(&hyperbus->rpc, true);
> +	error = rpcif_hw_init(&hyperbus->rpc, true);
> +	if (error)
> +		return error;
>  
>  	hyperbus->hbdev.map.size = hyperbus->rpc.size;
>  	hyperbus->hbdev.map.virt = hyperbus->rpc.dirmap;

This needs to rpcif_disable_rpm() before returning, AFAICT.

> +++ b/drivers/spi/spi-rpc-if.c
> @@ -156,7 +156,9 @@ static int rpcif_spi_probe(struct platform_device *pdev)
>  	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_TX_QUAD | SPI_RX_QUAD;
>  	ctlr->flags = SPI_CONTROLLER_HALF_DUPLEX;
>  
> -	rpcif_hw_init(rpc, false);
> +	error = rpcif_hw_init(rpc, false);
> +	if (error)
> +		return error;
>  
>  	error = spi_register_controller(ctlr);
>  	if (error) {

Same here.

Best regards,
								Pavel

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 5.10.y-cip 00/27] Add RPCIF, SCI{F1} support to Renesas RZ/G2L SoC

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 780 bytes --]

Hi!

> This patch series add support for the below:
> * Adds a generic property "output-impedance-ohms"
> * Pinctrl driver update to support set/get drive-strength and
>   output-impedance-ohms
> * Driver fixes and updates for RPC-IF
> * Support to SPI Multi I/O Bus controller (RPC-IF) for RZ/G2L
> * Support to SCI for RZ/G2L SoC
> * DTS updates for RZ/G2L SMARC
> 
> All the patches have been cherry-picked from Linux v5.17-rc2.

I found some minor details, but overall series looks okay. I'm
currently running tests, I can apply it if it passes and if there are
no other comments.

Best regards,
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 5.10.y-cip 00/27] Add RPCIF, SCI{F1} support to Renesas RZ/G2L SoC

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 720 bytes --]

Hi!

> This patch series add support for the below:
> * Adds a generic property "output-impedance-ohms"
> * Pinctrl driver update to support set/get drive-strength and
>   output-impedance-ohms
> * Driver fixes and updates for RPC-IF
> * Support to SPI Multi I/O Bus controller (RPC-IF) for RZ/G2L
> * Support to SCI for RZ/G2L SoC
> * DTS updates for RZ/G2L SMARC
> 
> All the patches have been cherry-picked from Linux v5.17-rc2.

Testing did not uncover any kernel problems. I have applied the
patches and pushed the tree.

Best regards,
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 195 bytes --]

Re: [PATCH 5.10.y-cip 01/27] dt-bindings: pincfg-node: Add "output-impedance-ohms" property

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 785 bytes --]

Hi!

> +++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
> @@ -114,6 +114,9 @@ properties:
>      description: enable output on a pin without actively driving it
>        (such as enabling an output buffer)
>  
> +  output-impedance-ohms:
> +    description: set the output impedance of a pin to at most X ohms
> +

Is that right description ("at most")? Later in the bindings you
support specific values, which IMO makes sense, without relying on the
"at most" part.

If dts asks for 1000 ohms impedance and implementation sets it to 10
ohms, that will cause problems, no?

Best regards,
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 195 bytes --]

RE: [PATCH 5.10.y-cip 01/27] dt-bindings: pincfg-node: Add "output-impedance-ohms" property

[Prabhakar Mahadev Lad]

Hi Pavel,

Thank you for the review.

> -----Original Message-----
> From: Pavel Machek <pavel@denx.de>
> Sent: 13 August 2022 14:45
> To: Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Cc: cip-dev@lists.cip-project.org; Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>; Pavel Machek
> <pavel@denx.de>; Biju Das <biju.das.jz@bp.renesas.com>
> Subject: Re: [PATCH 5.10.y-cip 01/27] dt-bindings: pincfg-node: Add "output-impedance-ohms" property
> 
> Hi!
> 
> > +++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
> > @@ -114,6 +114,9 @@ properties:
> >      description: enable output on a pin without actively driving it
> >        (such as enabling an output buffer)
> >
> > +  output-impedance-ohms:
> > +    description: set the output impedance of a pin to at most X ohms
> > +
> 
> Is that right description ("at most")? Later in the bindings you support specific values, which IMO
> makes sense, without relying on the "at most" part.
> 
I have followed the description text as used in pincfg-node.yaml file previously.

> If dts asks for 1000 ohms impedance and implementation sets it to 10 ohms, that will cause problems,
> no?
> 
I think since pincfg-node.yaml file is generic, hence this description, later the dt binding file which will actually uses this property will have to specify what values are appropriate that needs to be set in dts/i.


Cheers,
Prabhakar

> Best regards,
> 								Pavel
> --
> DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany