All of lore.kernel.org
 help / color / mirror / Atom feed
From: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
To: <ath11k@lists.infradead.org>
Cc: <linux-wireless@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<robh@kernel.org>,
	Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Subject: [PATCH v3 00/12] add support for WCN6750
Date: Mon, 28 Mar 2022 15:18:26 +0530	[thread overview]
Message-ID: <20220328094838.14093-1-quic_mpubbise@quicinc.com> (raw)

WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390/WCN6855 which
are DBS (dual band simultaneous) solutions (2 LMACs), WCN6750 has a
single LMAC supporting 2G, 5G and 6G bands. It can be operated only
on one band at any given point.

WCN6750 is a PCIe device. Unlike other supported ATH11K PCIe devices
which are directly attached to APSS (Application Processor SubSystem),
WCN6750 is not attached to APSS, it is attached to the WPSS
(Wireless Processor SubSystem) Q6 processor, the FW which runs on the
Q6 processor will enumerate the PCIe device. Since APSS is unaware of
such a device, it has to be registered as a platform device(AHB) to the
kernel for device probing. Like other AHB devices, remoteproc APIs are
used to boot up or shutdown of WCN6750.

WCN6750 uses both AHB and PCIe ATH11K APIs for it's operation.
It uses AHB APIs for device probe and booting of the remote processor.
Once device is booted up, it uses ATH11K PCIe APIs for initialization
and register access. Hence, it is referred as hybrid bus device in
the rest of this series.

Since the chip is enumerated by WPSS Q6, device information like
BAR and BAR size is not known to the APSS processor. A new QMI message
called device info QMI request will be sent to the target for fetching
these details.

STA and AP modes are supported; Basic connectivity and ping are
verified in both the modes.

An important point to note is that though WCN6750 is a PCIe device,
it cannot be attached to any other platform except on Qualcomm
Snapdragon SoCs due to the aforementioned reasons.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Manikanta Pubbisetty (12):
  dt: bindings: net: add bindings of WCN6750 for ath11k
  ath11k: Add HW params for WCN6750
  ath11k: Add bus params for WCN6750
  ath11k: Add register access logic for WCN6750
  ath11k: Fetch device information via QMI for WCN6750
  ath11k: Add QMI changes for WCN6750
  ath11k: HAL changes to support WCN6750
  ath11k: Datapath changes to support WCN6750
  ath11k: Do not put HW in DBS mode for WCN6750
  ath11k: WMI changes to support WCN6750
  ath11k: Update WBM idle ring HP after FW mode on
  ath11k: Add support for WCN6750 device
---
Note:
*	Remoteproc driver changes for WCN6750 which takes care of
	downloading the FW and booting of Q6 processor are under
	upstream review.
	Link: https://patchwork.kernel.org/project/linux-remoteproc/cover/1643712724-12436-1-git-send-email-quic_mpubbise@quicinc.com/

*	Also dependent on Series "Refactor PCI code to support WCN6750"
	Link: https://patchwork.kernel.org/project/linux-wireless/cover/20220328055714.6449-1-quic_mpubbise@quicinc.com/

V3:
 - Patch series with 19 patches is split in 2 patch series, this is the second one
 - Rebased on ToT SHAID: 7316a74e54318d0cd648242b18ea83cdef6dda96
 - Addessed DT binding concerns
 - PCI common code is moved to ath11k.ko
 - Added a new HW param for WCN6750 which uses fixed firmware memory, this is
   needed to differentiate WCN6750 from other ATH11K chipsets
 - Modified the logic in patch "ath11k: Add support for WCN6750 device" based on the latest DT binding

V2:
 - Rebased on ToT
 - Addressed comments on DT binding

 .../bindings/net/wireless/qcom,ath11k.yaml    | 361 ++++++++++++------
 drivers/net/wireless/ath/ath11k/Makefile      |   5 +-
 drivers/net/wireless/ath/ath11k/ahb.c         | 162 +++++++-
 drivers/net/wireless/ath/ath11k/ahb.h         |   1 +
 drivers/net/wireless/ath/ath11k/ce.c          |   4 +-
 drivers/net/wireless/ath/ath11k/core.c        | 118 +++++-
 drivers/net/wireless/ath/ath11k/core.h        |   5 +
 drivers/net/wireless/ath/ath11k/hal.c         |  15 +-
 drivers/net/wireless/ath/ath11k/hal.h         |  15 +-
 drivers/net/wireless/ath/ath11k/hw.c          | 166 ++++++++
 drivers/net/wireless/ath/ath11k/hw.h          |  11 +
 drivers/net/wireless/ath/ath11k/pci.c         |   4 +
 drivers/net/wireless/ath/ath11k/pcic.c        |  76 ++--
 drivers/net/wireless/ath/ath11k/qmi.c         | 220 +++++++++--
 drivers/net/wireless/ath/ath11k/qmi.h         |  26 +-
 drivers/net/wireless/ath/ath11k/wmi.c         |  13 +-
 16 files changed, 976 insertions(+), 226 deletions(-)

-- 
2.35.1


WARNING: multiple messages have this Message-ID (diff)
From: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
To: <ath11k@lists.infradead.org>
Cc: <linux-wireless@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<robh@kernel.org>,
	Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Subject: [PATCH v3 00/12] add support for WCN6750
Date: Mon, 28 Mar 2022 15:18:26 +0530	[thread overview]
Message-ID: <20220328094838.14093-1-quic_mpubbise@quicinc.com> (raw)

WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390/WCN6855 which
are DBS (dual band simultaneous) solutions (2 LMACs), WCN6750 has a
single LMAC supporting 2G, 5G and 6G bands. It can be operated only
on one band at any given point.

WCN6750 is a PCIe device. Unlike other supported ATH11K PCIe devices
which are directly attached to APSS (Application Processor SubSystem),
WCN6750 is not attached to APSS, it is attached to the WPSS
(Wireless Processor SubSystem) Q6 processor, the FW which runs on the
Q6 processor will enumerate the PCIe device. Since APSS is unaware of
such a device, it has to be registered as a platform device(AHB) to the
kernel for device probing. Like other AHB devices, remoteproc APIs are
used to boot up or shutdown of WCN6750.

WCN6750 uses both AHB and PCIe ATH11K APIs for it's operation.
It uses AHB APIs for device probe and booting of the remote processor.
Once device is booted up, it uses ATH11K PCIe APIs for initialization
and register access. Hence, it is referred as hybrid bus device in
the rest of this series.

Since the chip is enumerated by WPSS Q6, device information like
BAR and BAR size is not known to the APSS processor. A new QMI message
called device info QMI request will be sent to the target for fetching
these details.

STA and AP modes are supported; Basic connectivity and ping are
verified in both the modes.

An important point to note is that though WCN6750 is a PCIe device,
it cannot be attached to any other platform except on Qualcomm
Snapdragon SoCs due to the aforementioned reasons.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Manikanta Pubbisetty (12):
  dt: bindings: net: add bindings of WCN6750 for ath11k
  ath11k: Add HW params for WCN6750
  ath11k: Add bus params for WCN6750
  ath11k: Add register access logic for WCN6750
  ath11k: Fetch device information via QMI for WCN6750
  ath11k: Add QMI changes for WCN6750
  ath11k: HAL changes to support WCN6750
  ath11k: Datapath changes to support WCN6750
  ath11k: Do not put HW in DBS mode for WCN6750
  ath11k: WMI changes to support WCN6750
  ath11k: Update WBM idle ring HP after FW mode on
  ath11k: Add support for WCN6750 device
---
Note:
*	Remoteproc driver changes for WCN6750 which takes care of
	downloading the FW and booting of Q6 processor are under
	upstream review.
	Link: https://patchwork.kernel.org/project/linux-remoteproc/cover/1643712724-12436-1-git-send-email-quic_mpubbise@quicinc.com/

*	Also dependent on Series "Refactor PCI code to support WCN6750"
	Link: https://patchwork.kernel.org/project/linux-wireless/cover/20220328055714.6449-1-quic_mpubbise@quicinc.com/

V3:
 - Patch series with 19 patches is split in 2 patch series, this is the second one
 - Rebased on ToT SHAID: 7316a74e54318d0cd648242b18ea83cdef6dda96
 - Addessed DT binding concerns
 - PCI common code is moved to ath11k.ko
 - Added a new HW param for WCN6750 which uses fixed firmware memory, this is
   needed to differentiate WCN6750 from other ATH11K chipsets
 - Modified the logic in patch "ath11k: Add support for WCN6750 device" based on the latest DT binding

V2:
 - Rebased on ToT
 - Addressed comments on DT binding

 .../bindings/net/wireless/qcom,ath11k.yaml    | 361 ++++++++++++------
 drivers/net/wireless/ath/ath11k/Makefile      |   5 +-
 drivers/net/wireless/ath/ath11k/ahb.c         | 162 +++++++-
 drivers/net/wireless/ath/ath11k/ahb.h         |   1 +
 drivers/net/wireless/ath/ath11k/ce.c          |   4 +-
 drivers/net/wireless/ath/ath11k/core.c        | 118 +++++-
 drivers/net/wireless/ath/ath11k/core.h        |   5 +
 drivers/net/wireless/ath/ath11k/hal.c         |  15 +-
 drivers/net/wireless/ath/ath11k/hal.h         |  15 +-
 drivers/net/wireless/ath/ath11k/hw.c          | 166 ++++++++
 drivers/net/wireless/ath/ath11k/hw.h          |  11 +
 drivers/net/wireless/ath/ath11k/pci.c         |   4 +
 drivers/net/wireless/ath/ath11k/pcic.c        |  76 ++--
 drivers/net/wireless/ath/ath11k/qmi.c         | 220 +++++++++--
 drivers/net/wireless/ath/ath11k/qmi.h         |  26 +-
 drivers/net/wireless/ath/ath11k/wmi.c         |  13 +-
 16 files changed, 976 insertions(+), 226 deletions(-)

-- 
2.35.1


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

             reply	other threads:[~2022-03-28  9:49 UTC|newest]

Thread overview: 40+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-03-28  9:48 Manikanta Pubbisetty [this message]
2022-03-28  9:48 ` [PATCH v3 00/12] add support for WCN6750 Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 01/12] dt: bindings: net: add bindings of WCN6750 for ath11k Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-29 23:37   ` Rob Herring
2022-03-29 23:37     ` Rob Herring
2022-03-30  5:19     ` Manikanta Pubbisetty
2022-03-30  5:19       ` Manikanta Pubbisetty
2022-04-04 19:11   ` Matthias Kaehlcke
2022-04-04 19:11     ` Matthias Kaehlcke
2022-04-05  6:25     ` Manikanta Pubbisetty
2022-04-05  6:25       ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 02/12] ath11k: Add HW params for WCN6750 Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 03/12] ath11k: Add bus " Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 04/12] ath11k: Add register access logic " Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 05/12] ath11k: Fetch device information via QMI " Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 06/12] ath11k: Add QMI changes " Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 07/12] ath11k: HAL changes to support WCN6750 Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 08/12] ath11k: Datapath " Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 09/12] ath11k: Do not put HW in DBS mode for WCN6750 Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 10/12] ath11k: WMI changes to support WCN6750 Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 11/12] ath11k: Update WBM idle ring HP after FW mode on Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
2022-03-28  9:48 ` [PATCH v3 12/12] ath11k: Add support for WCN6750 device Manikanta Pubbisetty
2022-03-28  9:48   ` Manikanta Pubbisetty
  -- strict thread matches above, loose matches on Subject: below --
2022-03-28  6:09 [PATCH v3 00/12] add support for WCN6750 Manikanta Pubbisetty
2022-03-28  6:09 ` Manikanta Pubbisetty
2022-03-30  7:50 ` Manikanta Pubbisetty
2022-03-30  7:50   ` Manikanta Pubbisetty
2022-03-30  7:59   ` Kalle Valo
2022-03-30  7:59     ` Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220328094838.14093-1-quic_mpubbise@quicinc.com \
    --to=quic_mpubbise@quicinc.com \
    --cc=ath11k@lists.infradead.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.