* Aw: Re: Leadtek Winfast TV2100
@ 2009-11-21 22:33 hermann-pitton
2009-11-22 12:51 ` Terry Wu
0 siblings, 1 reply; 12+ messages in thread
From: hermann-pitton @ 2009-11-21 22:33 UTC (permalink / raw)
To: pavle.predic, terrywu2009, hermann-pitton; +Cc: video4linux-list
Hi,
sorry, posting from a webmail interface.
Might get bounced from the list.
----- Original Nachricht ----
Von: Pavle Predic <pavle.predic@yahoo.co.uk>
An: Terry Wu <terrywu2009@gmail.com>, hermann pitton <hermann-pitton@arcor.de>
Datum: 21.11.2009 20:53
Betreff: Re: Leadtek Winfast TV2100
> Hey Terry,
>
> Thanks for your input. Yes it would seem that my tuner is not supported
> (it's a YMEC Tvision TVF88T5-B/DFF), and neither is my board. But I was
> hoping that an existing board/tuner combination might do the job.
>
> @Hermann - I tried card IDs 1-150 with tuner=69 and - alas - didn't get
> sound. Interestingly enough, almost all card ids produce a picture with this
> tuner. Also, I noticed that with some board IDs I'm getting clicks when
> muting/unmuting or switching channels, but no broadcast sound
> whatsoever...:(
Tuner=69 covers a lot of tuners with TexasInstruments pll chip, NTSC and PAL.
I looked up this tuner from your previous mail and 69 is correct. You will note this when it comes to radio, UHF frequencies and takeover frequencies.
> I also tried running regspy.exe (after booting to Windows) and performed the
> test as described on dscaler site. But the results are way to cryptic for
> me...I have no clue how to use this. So I'll paste it here, and maybe
> someone will be able to draw a conclusion:
>
Ah, good.
> SAA7130 Card [0]:
>
> Vendor ID: 0x1131
> Device ID: 0x7130
> Subsystem ID: 0x6f3a107d
>
>
> 7 states dumped
>
> ----------------------------------------------------------------------------
> ------
>
> SAA7130 Card - State 0:
> SAA7134_GPIO_GPMODE: 80000009 * (10000000 00000000 00000000
> 00001001)
> SAA7134_GPIO_GPSTATUS: 0606200c * (00000110 00000110 00100000
> 00001100)
> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>
> SAA7134_ANALOG_IO_SELECT: 3b * (00111011)
>
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
>
> Changes: State 0 -> State 1:
> SAA7134_GPIO_GPMODE: 80000009 -> 8000000d (-------- --------
> -------- -----0--)
> SAA7134_GPIO_GPSTATUS: 0606200c -> 00062000 (-----11- --------
> -------- ----11--)
> SAA7134_ANALOG_IO_SELECT: 3b -> 00 (--111-11)
>
>
> 3 changes
>
>
> ----------------------------------------------------------------------------
> ------
>
> SAA7130 Card - State 1:
> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> 00001101) (was: 80000009)
> SAA7134_GPIO_GPSTATUS: 00062000 * (00000000 00000110 00100000
> 00000000) (was: 0606200c)
> SAA7134_ANALOG_IN_CTRL1: c1 * (11000001)
>
> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
> (was: 3b)
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
>
> Changes: State 1 -> State 2:
> SAA7134_GPIO_GPSTATUS: 00062000 -> 00062008 (-------- --------
> -------- ----0---)
> SAA7134_ANALOG_IN_CTRL1: c1 -> 83 (-1----0-)
>
> SAA7134_ANALOG_IO_SELECT: 00 -> 09 (----0--0)
>
>
> 3 changes
>
>
> ----------------------------------------------------------------------------
> ------
>
> SAA7130 Card - State 2:
> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> 00001101)
> SAA7134_GPIO_GPSTATUS: 00062008 (00000000 00000110 00100000
> 00001000) (was: 00062000)
> SAA7134_ANALOG_IN_CTRL1: 83 * (10000011)
> (was: c1)
> SAA7134_ANALOG_IO_SELECT: 09 (00001001)
> (was: 00)
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
>
> Changes: State 2 -> State 3:
> SAA7134_ANALOG_IN_CTRL1: 83 -> c8 (-0--0-11)
>
>
> 1 changes
>
>
> ----------------------------------------------------------------------------
> ------
>
> SAA7130 Card - State 3:
> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> 00001101)
> SAA7134_GPIO_GPSTATUS: 00062008 * (00000000 00000110 00100000
> 00001000)
> SAA7134_ANALOG_IN_CTRL1: c8 * (11001000)
> (was: 83)
> SAA7134_ANALOG_IO_SELECT: 09 * (00001001)
>
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
>
> Changes: State 3 -> State 4:
> SAA7134_GPIO_GPSTATUS: 00062008 -> 04062004 (-----0-- --------
> -------- ----10--)
> SAA7134_ANALOG_IN_CTRL1: c8 -> c1 (----1--0)
> (same as 0, 1)
> SAA7134_ANALOG_IO_SELECT: 09 -> 00 (----1--1)
> (same as 1)
>
> 3 changes
>
>
> ----------------------------------------------------------------------------
> ------
>
> SAA7130 Card - State 4:
> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> 00001101)
> SAA7134_GPIO_GPSTATUS: 04062004 * (00000100 00000110 00100000
> 00000100) (was: 00062008)
> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> (was: c8)
> SAA7134_ANALOG_IO_SELECT: 00 (00000000)
> (was: 09)
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
>
> Changes: State 4 -> State 5:
> SAA7134_GPIO_GPSTATUS: 04062004 -> 02062000 (-----10- --------
> -------- -----1--)
>
> 1 changes
>
>
> ----------------------------------------------------------------------------
> ------
>
> SAA7130 Card - State 5:
> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> 00001101)
> SAA7134_GPIO_GPSTATUS: 02062000 * (00000010 00000110 00100000
> 00000000) (was: 04062004)
> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>
> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
>
> Changes: State 5 -> Register Dump:
> SAA7134_GPIO_GPSTATUS: 02062000 -> 06062008 (-----0-- --------
> -------- ----0---)
> SAA7134_ANALOG_IO_SELECT: 00 -> 02 (------0-)
>
>
> 2 changes
>
>
> ============================================================================
> =====
>
> SAA7130 Card - Register Dump:
> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> 00001101)
> SAA7134_GPIO_GPSTATUS: 06062008 (00000110 00000110 00100000
> 00001000) (was: 02062000)
> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>
> SAA7134_ANALOG_IO_SELECT: 02 (00000010)
> (was: 00)
> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> 00000000)
> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>
> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>
> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>
> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>
> SAA7134_TS_PARALLEL: 04 (00000100)
>
> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>
> SAA7134_TS_SERIAL0: 00 (00000000)
>
> SAA7134_TS_SERIAL1: 00 (00000000)
>
> SAA7134_TS_DMA0: 00 (00000000)
>
> SAA7134_TS_DMA1: 00 (00000000)
>
> SAA7134_TS_DMA2: 00 (00000000)
>
> SAA7134_SPECIAL_MODE: 01 (00000001)
>
>
> end of dump
>
> Here is the order in which I performed the test:State 6
> State 0 - viewing software off
> State 1 - tuner mode
> State 2 - composite mode
> State 3 - s video mode
> State 4 - radio mode
> State 5 - tuner mode (again)
> Final dump - viewing software off (again)
>
> Thanks to everyone for your help.
>
> Pavle.
>
Better don't top post. Becomes hard to read after a while.
You would try wsith a gpio_mask = 0x0d.
.gpio for TV is 0x00000000 (default, don't even need to set it).
For s-video and composite 0x08.
For radio 0x04.
On saa7130 chips mono audio from tuner in most cases is connected to LINE2.
Then also radio is on LINE2 and s-video and composite on LINE1.
For .mute it seems to switch to s-video/composite LINE input and keeps that input open with .gpio 0x08.
Maybe Terry knows better.
Good luck for testing.
Cheers,
Hermann
>
> ________________________________
> From: Terry Wu <terrywu2009@gmail.com>
> To: hermann pitton <hermann-pitton@arcor.de>
> Cc: Pavle Predic <pavle.predic@yahoo.co.uk>; video4linux-list@redhat.com
> Sent: Sat, 21 November, 2009 10:07:05
> Subject: Re: Leadtek Winfast TV2100
>
> Hi,
>
> There are many models of TV2100.
> Different model uses different TV tuner.
>
> The tuner 69 is TUNER_TNF_5335MF.
> Make sure the tuner in your TV2100 card is the TNF_5335MF.
>
> Maybe the tuner in your TV2100 card is not supported by current
> v4l-dvb driver yet (linux\include\media\tuner.h).
>
>
> Terry
>
> 2009/11/21 hermann pitton <hermann-pitton@arcor.de>:
> > Hi Pavle,
> >
> > Am Freitag, den 20.11.2009, 14:11 +0000 schrieb Pavle Predic:
> >> Hi Hermann,
> >>
> >> Thank you so much for your help. I didn't really get most of what you
> >> said (way to technical for me), but at least I know now which tuner I
> >> should use, so I'll keep testing with tuner 69 and see if I get
> >> results.
> >
> > that one should be right, especially for analog radio.
> >
> >> BTW, I'm not from UK - I'm from Serbia and I'm trying to make the card
> >> work for my cable tv which uses PAL BG (at least so they say).
> >
> > Lots of people are on the move these days, therefore it is important to
> > know too, what they might carry with them. That tuner should be fine
> > then.
> >
> >> I'll report back after testing on tuner 69 (I'll simply try all card
> >> ids with this tuner id). In the meantime here's some more info:
> >
> > Better is to follow the advice how you can narrow down such stuff.
> >
> > As far I know, we have not destroyed a single device yet on the saa7134
> > driver, but to go over all possibilities, concerning voltage and gpios,
> > has some risks and is not the shortest way to come closer.
> >
> > Thanks for your input.
> >
> > Cheers,
> > Hermann
> >
> >> dmesg:
> >>
> >> [ 9.829338] saa7130/34: v4l2 driver version 0.2.15 loaded
> >> [ 9.829408] saa7134 0000:00:08.0: PCI INT A -> GSI 17 (level, low)
> >> -> IRQ 17
> >> [ 9.829419] saa7130[0]: found at 0000:00:08.0, rev: 1, irq: 17,
> >> latency: 64, mmio: 0xfdffe000
> >> [ 9.829428] saa7130[0]: subsystem: 107d:6f3a, board:
> >> UNKNOWN/GENERIC [card=0,autodetected]
> >> [ 9.829458] saa7130[0]: board init: gpio is 6200c
> >> [ 9.829465] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on
> >> shared IRQs
> >> [ 9.980513] saa7130[0]: i2c eeprom 00: 7d 10 3a 6f 54 20 1c 00 43
> >> 43 a9 1c 55 d2 b2 92
> >> [ 9.980532] saa7130[0]: i2c eeprom 10: 0c ff 82 0e ff 20 ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980547] saa7130[0]: i2c eeprom 20: 01 40 02 03 03 02 01 03 08
> >> ff 00 8c ff ff ff ff
> >> [ 9.980562] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980578] saa7130[0]: i2c eeprom 40: 50 89 00 c2 00 00 02 30 02
> >> ff ff ff ff ff ff ff
> >> [ 9.980593] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980608] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980623] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980639] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980654] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980670] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980685] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980701] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980716] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980731] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980747] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff
> >> ff ff ff ff ff ff ff
> >> [ 9.980876] saa7130[0]: registered device video0 [v4l2]
> >> [ 9.980908] saa7130[0]: registered device vbi0
> >>
> >>
> >> lsmod:
> >>
> >> saa7134 135552 0
> >> ir_common 47172 1 saa7134
> >> v4l2_common 14308 1 saa7134
> >> videodev 31040 2 saa7134,v4l2_common
> >> videobuf_dma_sg 11340 1 saa7134
> >> videobuf_core 16164 2 saa7134,videobuf_dma_sg
> >> tveeprom 10720 1 saa7134
> >> i2c_core 20844 4
> >> i2c_viapro,saa7134,v4l2_common,tveeprom
> >>
> >> lspci:
> >>
> >> 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130
> >> Video Broadcast Decoder [1131:7130] (rev 01)
> >> Subsystem: LeadTek Research Inc. Device [107d:6f3a]
> >> Flags: bus master, medium devsel, latency 64, IRQ 17
> >> Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
> >> Capabilities: [40] Power Management version 1
> >> Kernel driver in use: saa7134
> >> Kernel modules: saa7134
> >>
> >> Thanks again,
> >>
> >> Pavle.
> >>
> >>
> >>
> >>
> >>
> >> ______________________________________________________________________
> >> From: hermann pitton <hermann-pitton@arcor.de>
> >> To: Pavle Predic <pavle.predic@yahoo.co.uk>
> >> Cc: video4linux-list@redhat.com
> >> Sent: Sun, 8 November, 2009 23:35:08
> >> Subject: Re: Leadtek Winfast TV2100
> >>
> >> Hi Pavle,
> >>
> >> Am Sonntag, den 08.11.2009, 17:11 +0000 schrieb Pavle Predic:
> >> > Did anyone manage to get this card working on Linux? I got the
> >> picture out of the box, but it's impossible to get any sound from the
> >> damned thing. The card is not on CARDLIST.saa7134, but I assume a
> >> similar card/tuner combination can be used. But which? By the way, I
> >> got the speakers connected directly to card output, I'm not even
> >> trying to get it working with my sound card. I can hear clicks when
> >> loading/unloading modules, so it's alive but not set up properly.
> >> >
> >> > Any info would be greatly appreciated. Perhaps someone knows of
> >> another card that is similar to this one?
> >> >
> >> > Card info:
> >> > Chipset: saa7134
> >> > Tuner: Tvision TVF88T5-B/DFF
> >> > Card numbers that produce picture (modprobe saa7134 card=$n): 3, 7,
> >> 10, 16, 34, 35, 45, 46, 47, 48, 51, 63, 64, 68
> >>
> >> that is not enough information yet.
> >>
> >> The correct tuner for this one is tuner=69.
> >>
> >> Only with this one you will have also radio support.
> >>
> >> Since you mail from an UK mail provider, this tuner is not expected to
> >> work with PAL-I TV stereo sound there, but radio would work.
> >>
> >> Else, if neither amux = TV nor amux = LINE1 or LINE2 (LINE inputs for
> >> TV
> >> sound are only found on saa7130 chips, except there is also an extra
> >> TV
> >> mono section directly from the tuner) work for TV sound, most often
> >> an
> >> external audio mux is in the way and needs to be configured correctly
> >> with saa7134 gpio pins. Looking also at the minor chips on the card
> >> with
> >> more than 3 pins can reveal such a mux.
> >>
> >> There is also a software test on such hardware, succeeding in most
> >> cases.
> >>
> >> By default, external analog audio input is looped through to analog
> >> audio out, on which you are listening, if the driver is unloaded.
> >>
> >> On a saa7134 chip, on saa7130 are some known specials, you should hear
> >> the incoming sound directly on your headphones or what else you might
> >> be
> >> using directly connected to your card, trying on LINE1 and LINE2 for
> >> that.
> >>
> >> If not, you can expect that such a mux chip needs to be treated
> >> correctly.
> >>
> >> The DScaler (deinterlace.sf.net) regspy.exe often can help to identify
> >> such gpios in use, else you must trace lines and resistors on it.
> >>
> >> In general, an absolute minimum is to provide related "dmesg" after
> >> loading the driver _without_ having tried on other cards previously.
> >>
> >> Please read more on the linuxtv.org wiki about adding support for a
> >> new
> >> card.
> >>
> >> Cheers,
> >> Hermann
> >
> >
Jetzt NEU: Do it youself E-Cards bei Arcor.de!
Stellen Sie Ihr eigenes Unikat zusammen und machen Sie dem Empfänger eine ganz persönliche Freude!
E-Card Marke Eigenbau: HIER KLICKEN: http://www.arcor.de/rd/footer.ecard
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-21 22:33 Aw: Re: Leadtek Winfast TV2100 hermann-pitton
@ 2009-11-22 12:51 ` Terry Wu
2009-11-22 22:30 ` hermann pitton
0 siblings, 1 reply; 12+ messages in thread
From: Terry Wu @ 2009-11-22 12:51 UTC (permalink / raw)
To: hermann-pitton; +Cc: video4linux-list
Hi,
I will give you the tuner data sheet and schematic of GPIO tomorrow.
Stay tuned.
Terry
2009/11/22 <hermann-pitton@arcor.de>:
> Hi,
>
> sorry, posting from a webmail interface.
>
> Might get bounced from the list.
>
> ----- Original Nachricht ----
> Von: Pavle Predic <pavle.predic@yahoo.co.uk>
> An: Terry Wu <terrywu2009@gmail.com>, hermann pitton <hermann-pitton@arcor.de>
> Datum: 21.11.2009 20:53
> Betreff: Re: Leadtek Winfast TV2100
>
>> Hey Terry,
>>
>> Thanks for your input. Yes it would seem that my tuner is not supported
>> (it's a YMEC Tvision TVF88T5-B/DFF), and neither is my board. But I was
>> hoping that an existing board/tuner combination might do the job.
>>
>> @Hermann - I tried card IDs 1-150 with tuner=69 and - alas - didn't get
>> sound. Interestingly enough, almost all card ids produce a picture with this
>> tuner. Also, I noticed that with some board IDs I'm getting clicks when
>> muting/unmuting or switching channels, but no broadcast sound
>> whatsoever...:(
>
> Tuner=69 covers a lot of tuners with TexasInstruments pll chip, NTSC and PAL.
> I looked up this tuner from your previous mail and 69 is correct. You will note this when it comes to radio, UHF frequencies and takeover frequencies.
>
>> I also tried running regspy.exe (after booting to Windows) and performed the
>> test as described on dscaler site. But the results are way to cryptic for
>> me...I have no clue how to use this. So I'll paste it here, and maybe
>> someone will be able to draw a conclusion:
>>
> Ah, good.
>
>> SAA7130 Card [0]:
>>
>> Vendor ID: 0x1131
>> Device ID: 0x7130
>> Subsystem ID: 0x6f3a107d
>>
>>
>> 7 states dumped
>>
>> ----------------------------------------------------------------------------
>> ------
>>
>> SAA7130 Card - State 0:
>> SAA7134_GPIO_GPMODE: 80000009 * (10000000 00000000 00000000
>> 00001001)
>> SAA7134_GPIO_GPSTATUS: 0606200c * (00000110 00000110 00100000
>> 00001100)
>> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>
>> SAA7134_ANALOG_IO_SELECT: 3b * (00111011)
>>
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>>
>> Changes: State 0 -> State 1:
>> SAA7134_GPIO_GPMODE: 80000009 -> 8000000d (-------- --------
>> -------- -----0--)
>> SAA7134_GPIO_GPSTATUS: 0606200c -> 00062000 (-----11- --------
>> -------- ----11--)
>> SAA7134_ANALOG_IO_SELECT: 3b -> 00 (--111-11)
>>
>>
>> 3 changes
>>
>>
>> ----------------------------------------------------------------------------
>> ------
>>
>> SAA7130 Card - State 1:
>> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> 00001101) (was: 80000009)
>> SAA7134_GPIO_GPSTATUS: 00062000 * (00000000 00000110 00100000
>> 00000000) (was: 0606200c)
>> SAA7134_ANALOG_IN_CTRL1: c1 * (11000001)
>>
>> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>> (was: 3b)
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>>
>> Changes: State 1 -> State 2:
>> SAA7134_GPIO_GPSTATUS: 00062000 -> 00062008 (-------- --------
>> -------- ----0---)
>> SAA7134_ANALOG_IN_CTRL1: c1 -> 83 (-1----0-)
>>
>> SAA7134_ANALOG_IO_SELECT: 00 -> 09 (----0--0)
>>
>>
>> 3 changes
>>
>>
>> ----------------------------------------------------------------------------
>> ------
>>
>> SAA7130 Card - State 2:
>> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> 00001101)
>> SAA7134_GPIO_GPSTATUS: 00062008 (00000000 00000110 00100000
>> 00001000) (was: 00062000)
>> SAA7134_ANALOG_IN_CTRL1: 83 * (10000011)
>> (was: c1)
>> SAA7134_ANALOG_IO_SELECT: 09 (00001001)
>> (was: 00)
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>>
>> Changes: State 2 -> State 3:
>> SAA7134_ANALOG_IN_CTRL1: 83 -> c8 (-0--0-11)
>>
>>
>> 1 changes
>>
>>
>> ----------------------------------------------------------------------------
>> ------
>>
>> SAA7130 Card - State 3:
>> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> 00001101)
>> SAA7134_GPIO_GPSTATUS: 00062008 * (00000000 00000110 00100000
>> 00001000)
>> SAA7134_ANALOG_IN_CTRL1: c8 * (11001000)
>> (was: 83)
>> SAA7134_ANALOG_IO_SELECT: 09 * (00001001)
>>
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>>
>> Changes: State 3 -> State 4:
>> SAA7134_GPIO_GPSTATUS: 00062008 -> 04062004 (-----0-- --------
>> -------- ----10--)
>> SAA7134_ANALOG_IN_CTRL1: c8 -> c1 (----1--0)
>> (same as 0, 1)
>> SAA7134_ANALOG_IO_SELECT: 09 -> 00 (----1--1)
>> (same as 1)
>>
>> 3 changes
>>
>>
>> ----------------------------------------------------------------------------
>> ------
>>
>> SAA7130 Card - State 4:
>> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> 00001101)
>> SAA7134_GPIO_GPSTATUS: 04062004 * (00000100 00000110 00100000
>> 00000100) (was: 00062008)
>> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>> (was: c8)
>> SAA7134_ANALOG_IO_SELECT: 00 (00000000)
>> (was: 09)
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>>
>> Changes: State 4 -> State 5:
>> SAA7134_GPIO_GPSTATUS: 04062004 -> 02062000 (-----10- --------
>> -------- -----1--)
>>
>> 1 changes
>>
>>
>> ----------------------------------------------------------------------------
>> ------
>>
>> SAA7130 Card - State 5:
>> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> 00001101)
>> SAA7134_GPIO_GPSTATUS: 02062000 * (00000010 00000110 00100000
>> 00000000) (was: 04062004)
>> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>
>> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>>
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>>
>> Changes: State 5 -> Register Dump:
>> SAA7134_GPIO_GPSTATUS: 02062000 -> 06062008 (-----0-- --------
>> -------- ----0---)
>> SAA7134_ANALOG_IO_SELECT: 00 -> 02 (------0-)
>>
>>
>> 2 changes
>>
>>
>> ============================================================================
>> =====
>>
>> SAA7130 Card - Register Dump:
>> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> 00001101)
>> SAA7134_GPIO_GPSTATUS: 06062008 (00000110 00000110 00100000
>> 00001000) (was: 02062000)
>> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>
>> SAA7134_ANALOG_IO_SELECT: 02 (00000010)
>> (was: 00)
>> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> 00000000)
>> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>
>> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>
>> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>
>> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>
>> SAA7134_TS_PARALLEL: 04 (00000100)
>>
>> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>
>> SAA7134_TS_SERIAL0: 00 (00000000)
>>
>> SAA7134_TS_SERIAL1: 00 (00000000)
>>
>> SAA7134_TS_DMA0: 00 (00000000)
>>
>> SAA7134_TS_DMA1: 00 (00000000)
>>
>> SAA7134_TS_DMA2: 00 (00000000)
>>
>> SAA7134_SPECIAL_MODE: 01 (00000001)
>>
>>
>> end of dump
>>
>> Here is the order in which I performed the test:State 6
>> State 0 - viewing software off
>> State 1 - tuner mode
>> State 2 - composite mode
>> State 3 - s video mode
>> State 4 - radio mode
>> State 5 - tuner mode (again)
>> Final dump - viewing software off (again)
>>
>> Thanks to everyone for your help.
>>
>> Pavle.
>>
>
> Better don't top post. Becomes hard to read after a while.
>
> You would try wsith a gpio_mask = 0x0d.
>
> .gpio for TV is 0x00000000 (default, don't even need to set it).
>
> For s-video and composite 0x08.
>
> For radio 0x04.
>
> On saa7130 chips mono audio from tuner in most cases is connected to LINE2.
>
> Then also radio is on LINE2 and s-video and composite on LINE1.
>
> For .mute it seems to switch to s-video/composite LINE input and keeps that input open with .gpio 0x08.
>
> Maybe Terry knows better.
>
> Good luck for testing.
>
> Cheers,
> Hermann
>
>>
>> ________________________________
>> From: Terry Wu <terrywu2009@gmail.com>
>> To: hermann pitton <hermann-pitton@arcor.de>
>> Cc: Pavle Predic <pavle.predic@yahoo.co.uk>; video4linux-list@redhat.com
>> Sent: Sat, 21 November, 2009 10:07:05
>> Subject: Re: Leadtek Winfast TV2100
>>
>> Hi,
>>
>> There are many models of TV2100.
>> Different model uses different TV tuner.
>>
>> The tuner 69 is TUNER_TNF_5335MF.
>> Make sure the tuner in your TV2100 card is the TNF_5335MF.
>>
>> Maybe the tuner in your TV2100 card is not supported by current
>> v4l-dvb driver yet (linux\include\media\tuner.h).
>>
>>
>> Terry
>>
>> 2009/11/21 hermann pitton <hermann-pitton@arcor.de>:
>> > Hi Pavle,
>> >
>> > Am Freitag, den 20.11.2009, 14:11 +0000 schrieb Pavle Predic:
>> >> Hi Hermann,
>> >>
>> >> Thank you so much for your help. I didn't really get most of what you
>> >> said (way to technical for me), but at least I know now which tuner I
>> >> should use, so I'll keep testing with tuner 69 and see if I get
>> >> results.
>> >
>> > that one should be right, especially for analog radio.
>> >
>> >> BTW, I'm not from UK - I'm from Serbia and I'm trying to make the card
>> >> work for my cable tv which uses PAL BG (at least so they say).
>> >
>> > Lots of people are on the move these days, therefore it is important to
>> > know too, what they might carry with them. That tuner should be fine
>> > then.
>> >
>> >> I'll report back after testing on tuner 69 (I'll simply try all card
>> >> ids with this tuner id). In the meantime here's some more info:
>> >
>> > Better is to follow the advice how you can narrow down such stuff.
>> >
>> > As far I know, we have not destroyed a single device yet on the saa7134
>> > driver, but to go over all possibilities, concerning voltage and gpios,
>> > has some risks and is not the shortest way to come closer.
>> >
>> > Thanks for your input.
>> >
>> > Cheers,
>> > Hermann
>> >
>> >> dmesg:
>> >>
>> >> [ 9.829338] saa7130/34: v4l2 driver version 0.2.15 loaded
>> >> [ 9.829408] saa7134 0000:00:08.0: PCI INT A -> GSI 17 (level, low)
>> >> -> IRQ 17
>> >> [ 9.829419] saa7130[0]: found at 0000:00:08.0, rev: 1, irq: 17,
>> >> latency: 64, mmio: 0xfdffe000
>> >> [ 9.829428] saa7130[0]: subsystem: 107d:6f3a, board:
>> >> UNKNOWN/GENERIC [card=0,autodetected]
>> >> [ 9.829458] saa7130[0]: board init: gpio is 6200c
>> >> [ 9.829465] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on
>> >> shared IRQs
>> >> [ 9.980513] saa7130[0]: i2c eeprom 00: 7d 10 3a 6f 54 20 1c 00 43
>> >> 43 a9 1c 55 d2 b2 92
>> >> [ 9.980532] saa7130[0]: i2c eeprom 10: 0c ff 82 0e ff 20 ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980547] saa7130[0]: i2c eeprom 20: 01 40 02 03 03 02 01 03 08
>> >> ff 00 8c ff ff ff ff
>> >> [ 9.980562] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980578] saa7130[0]: i2c eeprom 40: 50 89 00 c2 00 00 02 30 02
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980593] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980608] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980623] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980639] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980654] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980670] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980685] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980701] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980716] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980731] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980747] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff
>> >> ff ff ff ff ff ff ff
>> >> [ 9.980876] saa7130[0]: registered device video0 [v4l2]
>> >> [ 9.980908] saa7130[0]: registered device vbi0
>> >>
>> >>
>> >> lsmod:
>> >>
>> >> saa7134 135552 0
>> >> ir_common 47172 1 saa7134
>> >> v4l2_common 14308 1 saa7134
>> >> videodev 31040 2 saa7134,v4l2_common
>> >> videobuf_dma_sg 11340 1 saa7134
>> >> videobuf_core 16164 2 saa7134,videobuf_dma_sg
>> >> tveeprom 10720 1 saa7134
>> >> i2c_core 20844 4
>> >> i2c_viapro,saa7134,v4l2_common,tveeprom
>> >>
>> >> lspci:
>> >>
>> >> 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130
>> >> Video Broadcast Decoder [1131:7130] (rev 01)
>> >> Subsystem: LeadTek Research Inc. Device [107d:6f3a]
>> >> Flags: bus master, medium devsel, latency 64, IRQ 17
>> >> Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
>> >> Capabilities: [40] Power Management version 1
>> >> Kernel driver in use: saa7134
>> >> Kernel modules: saa7134
>> >>
>> >> Thanks again,
>> >>
>> >> Pavle.
>> >>
>> >>
>> >>
>> >>
>> >>
>> >> ______________________________________________________________________
>> >> From: hermann pitton <hermann-pitton@arcor.de>
>> >> To: Pavle Predic <pavle.predic@yahoo.co.uk>
>> >> Cc: video4linux-list@redhat.com
>> >> Sent: Sun, 8 November, 2009 23:35:08
>> >> Subject: Re: Leadtek Winfast TV2100
>> >>
>> >> Hi Pavle,
>> >>
>> >> Am Sonntag, den 08.11.2009, 17:11 +0000 schrieb Pavle Predic:
>> >> > Did anyone manage to get this card working on Linux? I got the
>> >> picture out of the box, but it's impossible to get any sound from the
>> >> damned thing. The card is not on CARDLIST.saa7134, but I assume a
>> >> similar card/tuner combination can be used. But which? By the way, I
>> >> got the speakers connected directly to card output, I'm not even
>> >> trying to get it working with my sound card. I can hear clicks when
>> >> loading/unloading modules, so it's alive but not set up properly.
>> >> >
>> >> > Any info would be greatly appreciated. Perhaps someone knows of
>> >> another card that is similar to this one?
>> >> >
>> >> > Card info:
>> >> > Chipset: saa7134
>> >> > Tuner: Tvision TVF88T5-B/DFF
>> >> > Card numbers that produce picture (modprobe saa7134 card=$n): 3, 7,
>> >> 10, 16, 34, 35, 45, 46, 47, 48, 51, 63, 64, 68
>> >>
>> >> that is not enough information yet.
>> >>
>> >> The correct tuner for this one is tuner=69.
>> >>
>> >> Only with this one you will have also radio support.
>> >>
>> >> Since you mail from an UK mail provider, this tuner is not expected to
>> >> work with PAL-I TV stereo sound there, but radio would work.
>> >>
>> >> Else, if neither amux = TV nor amux = LINE1 or LINE2 (LINE inputs for
>> >> TV
>> >> sound are only found on saa7130 chips, except there is also an extra
>> >> TV
>> >> mono section directly from the tuner) work for TV sound, most often
>> >> an
>> >> external audio mux is in the way and needs to be configured correctly
>> >> with saa7134 gpio pins. Looking also at the minor chips on the card
>> >> with
>> >> more than 3 pins can reveal such a mux.
>> >>
>> >> There is also a software test on such hardware, succeeding in most
>> >> cases.
>> >>
>> >> By default, external analog audio input is looped through to analog
>> >> audio out, on which you are listening, if the driver is unloaded.
>> >>
>> >> On a saa7134 chip, on saa7130 are some known specials, you should hear
>> >> the incoming sound directly on your headphones or what else you might
>> >> be
>> >> using directly connected to your card, trying on LINE1 and LINE2 for
>> >> that.
>> >>
>> >> If not, you can expect that such a mux chip needs to be treated
>> >> correctly.
>> >>
>> >> The DScaler (deinterlace.sf.net) regspy.exe often can help to identify
>> >> such gpios in use, else you must trace lines and resistors on it.
>> >>
>> >> In general, an absolute minimum is to provide related "dmesg" after
>> >> loading the driver _without_ having tried on other cards previously.
>> >>
>> >> Please read more on the linuxtv.org wiki about adding support for a
>> >> new
>> >> card.
>> >>
>> >> Cheers,
>> >> Hermann
>> >
>> >
>
>
> Jetzt NEU: Do it youself E-Cards bei Arcor.de!
> Stellen Sie Ihr eigenes Unikat zusammen und machen Sie dem Empfänger eine ganz persönliche Freude!
> E-Card Marke Eigenbau: HIER KLICKEN: http://www.arcor.de/rd/footer.ecard
>
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-22 12:51 ` Terry Wu
@ 2009-11-22 22:30 ` hermann pitton
2009-11-23 1:23 ` Terry Wu
0 siblings, 1 reply; 12+ messages in thread
From: hermann pitton @ 2009-11-22 22:30 UTC (permalink / raw)
To: Terry Wu; +Cc: video4linux-list
Hi,
Am Sonntag, den 22.11.2009, 20:51 +0800 schrieb Terry Wu:
> Hi,
>
> I will give you the tuner data sheet and schematic of GPIO tomorrow.
> Stay tuned.
>
> Terry
that is of course very welcome.
We know that the PLL chip is TI sn761677, datasheet is publicly
available, radio switch is 0x11 and inside is a TENA tuner PCB also
known from other tuners.
For the gpio configuration hopefully my assumptions should not be that
wrong.
Pavle, are you able to test such yourself or should I provide some
patches?
Cheers,
Hermann
> 2009/11/22 <hermann-pitton@arcor.de>:
> > Hi,
> >
> > sorry, posting from a webmail interface.
> >
> > Might get bounced from the list.
> >
> > ----- Original Nachricht ----
> > Von: Pavle Predic <pavle.predic@yahoo.co.uk>
> > An: Terry Wu <terrywu2009@gmail.com>, hermann pitton <hermann-pitton@arcor.de>
> > Datum: 21.11.2009 20:53
> > Betreff: Re: Leadtek Winfast TV2100
> >
> >> Hey Terry,
> >>
> >> Thanks for your input. Yes it would seem that my tuner is not supported
> >> (it's a YMEC Tvision TVF88T5-B/DFF), and neither is my board. But I was
> >> hoping that an existing board/tuner combination might do the job.
> >>
> >> @Hermann - I tried card IDs 1-150 with tuner=69 and - alas - didn't get
> >> sound. Interestingly enough, almost all card ids produce a picture with this
> >> tuner. Also, I noticed that with some board IDs I'm getting clicks when
> >> muting/unmuting or switching channels, but no broadcast sound
> >> whatsoever...:(
> >
> > Tuner=69 covers a lot of tuners with TexasInstruments pll chip, NTSC and PAL.
> > I looked up this tuner from your previous mail and 69 is correct. You will note this when it comes to radio, UHF frequencies and takeover frequencies.
> >
> >> I also tried running regspy.exe (after booting to Windows) and performed the
> >> test as described on dscaler site. But the results are way to cryptic for
> >> me...I have no clue how to use this. So I'll paste it here, and maybe
> >> someone will be able to draw a conclusion:
> >>
> > Ah, good.
> >
> >> SAA7130 Card [0]:
> >>
> >> Vendor ID: 0x1131
> >> Device ID: 0x7130
> >> Subsystem ID: 0x6f3a107d
> >>
> >>
> >> 7 states dumped
> >>
> >> ----------------------------------------------------------------------------
> >> ------
> >>
> >> SAA7130 Card - State 0:
> >> SAA7134_GPIO_GPMODE: 80000009 * (10000000 00000000 00000000
> >> 00001001)
> >> SAA7134_GPIO_GPSTATUS: 0606200c * (00000110 00000110 00100000
> >> 00001100)
> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >>
> >> SAA7134_ANALOG_IO_SELECT: 3b * (00111011)
> >>
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >>
> >> Changes: State 0 -> State 1:
> >> SAA7134_GPIO_GPMODE: 80000009 -> 8000000d (-------- --------
> >> -------- -----0--)
> >> SAA7134_GPIO_GPSTATUS: 0606200c -> 00062000 (-----11- --------
> >> -------- ----11--)
> >> SAA7134_ANALOG_IO_SELECT: 3b -> 00 (--111-11)
> >>
> >>
> >> 3 changes
> >>
> >>
> >> ----------------------------------------------------------------------------
> >> ------
> >>
> >> SAA7130 Card - State 1:
> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> 00001101) (was: 80000009)
> >> SAA7134_GPIO_GPSTATUS: 00062000 * (00000000 00000110 00100000
> >> 00000000) (was: 0606200c)
> >> SAA7134_ANALOG_IN_CTRL1: c1 * (11000001)
> >>
> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
> >> (was: 3b)
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >>
> >> Changes: State 1 -> State 2:
> >> SAA7134_GPIO_GPSTATUS: 00062000 -> 00062008 (-------- --------
> >> -------- ----0---)
> >> SAA7134_ANALOG_IN_CTRL1: c1 -> 83 (-1----0-)
> >>
> >> SAA7134_ANALOG_IO_SELECT: 00 -> 09 (----0--0)
> >>
> >>
> >> 3 changes
> >>
> >>
> >> ----------------------------------------------------------------------------
> >> ------
> >>
> >> SAA7130 Card - State 2:
> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> 00001101)
> >> SAA7134_GPIO_GPSTATUS: 00062008 (00000000 00000110 00100000
> >> 00001000) (was: 00062000)
> >> SAA7134_ANALOG_IN_CTRL1: 83 * (10000011)
> >> (was: c1)
> >> SAA7134_ANALOG_IO_SELECT: 09 (00001001)
> >> (was: 00)
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >>
> >> Changes: State 2 -> State 3:
> >> SAA7134_ANALOG_IN_CTRL1: 83 -> c8 (-0--0-11)
> >>
> >>
> >> 1 changes
> >>
> >>
> >> ----------------------------------------------------------------------------
> >> ------
> >>
> >> SAA7130 Card - State 3:
> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> 00001101)
> >> SAA7134_GPIO_GPSTATUS: 00062008 * (00000000 00000110 00100000
> >> 00001000)
> >> SAA7134_ANALOG_IN_CTRL1: c8 * (11001000)
> >> (was: 83)
> >> SAA7134_ANALOG_IO_SELECT: 09 * (00001001)
> >>
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >>
> >> Changes: State 3 -> State 4:
> >> SAA7134_GPIO_GPSTATUS: 00062008 -> 04062004 (-----0-- --------
> >> -------- ----10--)
> >> SAA7134_ANALOG_IN_CTRL1: c8 -> c1 (----1--0)
> >> (same as 0, 1)
> >> SAA7134_ANALOG_IO_SELECT: 09 -> 00 (----1--1)
> >> (same as 1)
> >>
> >> 3 changes
> >>
> >>
> >> ----------------------------------------------------------------------------
> >> ------
> >>
> >> SAA7130 Card - State 4:
> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> 00001101)
> >> SAA7134_GPIO_GPSTATUS: 04062004 * (00000100 00000110 00100000
> >> 00000100) (was: 00062008)
> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >> (was: c8)
> >> SAA7134_ANALOG_IO_SELECT: 00 (00000000)
> >> (was: 09)
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >>
> >> Changes: State 4 -> State 5:
> >> SAA7134_GPIO_GPSTATUS: 04062004 -> 02062000 (-----10- --------
> >> -------- -----1--)
> >>
> >> 1 changes
> >>
> >>
> >> ----------------------------------------------------------------------------
> >> ------
> >>
> >> SAA7130 Card - State 5:
> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> 00001101)
> >> SAA7134_GPIO_GPSTATUS: 02062000 * (00000010 00000110 00100000
> >> 00000000) (was: 04062004)
> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >>
> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
> >>
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >>
> >> Changes: State 5 -> Register Dump:
> >> SAA7134_GPIO_GPSTATUS: 02062000 -> 06062008 (-----0-- --------
> >> -------- ----0---)
> >> SAA7134_ANALOG_IO_SELECT: 00 -> 02 (------0-)
> >>
> >>
> >> 2 changes
> >>
> >>
> >> ============================================================================
> >> =====
> >>
> >> SAA7130 Card - Register Dump:
> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> 00001101)
> >> SAA7134_GPIO_GPSTATUS: 06062008 (00000110 00000110 00100000
> >> 00001000) (was: 02062000)
> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >>
> >> SAA7134_ANALOG_IO_SELECT: 02 (00000010)
> >> (was: 00)
> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> 00000000)
> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >>
> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >>
> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >>
> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >>
> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >>
> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >>
> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA0: 00 (00000000)
> >>
> >> SAA7134_TS_DMA1: 00 (00000000)
> >>
> >> SAA7134_TS_DMA2: 00 (00000000)
> >>
> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >>
> >>
> >> end of dump
> >>
> >> Here is the order in which I performed the test:State 6
> >> State 0 - viewing software off
> >> State 1 - tuner mode
> >> State 2 - composite mode
> >> State 3 - s video mode
> >> State 4 - radio mode
> >> State 5 - tuner mode (again)
> >> Final dump - viewing software off (again)
> >>
> >> Thanks to everyone for your help.
> >>
> >> Pavle.
> >>
> >
> > Better don't top post. Becomes hard to read after a while.
> >
> > You would try wsith a gpio_mask = 0x0d.
> >
> > .gpio for TV is 0x00000000 (default, don't even need to set it).
> >
> > For s-video and composite 0x08.
> >
> > For radio 0x04.
> >
> > On saa7130 chips mono audio from tuner in most cases is connected to LINE2.
> >
> > Then also radio is on LINE2 and s-video and composite on LINE1.
> >
> > For .mute it seems to switch to s-video/composite LINE input and keeps that input open with .gpio 0x08.
> >
> > Maybe Terry knows better.
> >
> > Good luck for testing.
> >
> > Cheers,
> > Hermann
> >
> >>
> >> ________________________________
> >> From: Terry Wu <terrywu2009@gmail.com>
> >> To: hermann pitton <hermann-pitton@arcor.de>
> >> Cc: Pavle Predic <pavle.predic@yahoo.co.uk>; video4linux-list@redhat.com
> >> Sent: Sat, 21 November, 2009 10:07:05
> >> Subject: Re: Leadtek Winfast TV2100
> >>
> >> Hi,
> >>
> >> There are many models of TV2100.
> >> Different model uses different TV tuner.
> >>
> >> The tuner 69 is TUNER_TNF_5335MF.
> >> Make sure the tuner in your TV2100 card is the TNF_5335MF.
> >>
> >> Maybe the tuner in your TV2100 card is not supported by current
> >> v4l-dvb driver yet (linux\include\media\tuner.h).
> >>
> >>
> >> Terry
> >>
> >> 2009/11/21 hermann pitton <hermann-pitton@arcor.de>:
> >> > Hi Pavle,
> >> >
> >> > Am Freitag, den 20.11.2009, 14:11 +0000 schrieb Pavle Predic:
> >> >> Hi Hermann,
> >> >>
> >> >> Thank you so much for your help. I didn't really get most of what you
> >> >> said (way to technical for me), but at least I know now which tuner I
> >> >> should use, so I'll keep testing with tuner 69 and see if I get
> >> >> results.
> >> >
> >> > that one should be right, especially for analog radio.
> >> >
> >> >> BTW, I'm not from UK - I'm from Serbia and I'm trying to make the card
> >> >> work for my cable tv which uses PAL BG (at least so they say).
> >> >
> >> > Lots of people are on the move these days, therefore it is important to
> >> > know too, what they might carry with them. That tuner should be fine
> >> > then.
> >> >
> >> >> I'll report back after testing on tuner 69 (I'll simply try all card
> >> >> ids with this tuner id). In the meantime here's some more info:
> >> >
> >> > Better is to follow the advice how you can narrow down such stuff.
> >> >
> >> > As far I know, we have not destroyed a single device yet on the saa7134
> >> > driver, but to go over all possibilities, concerning voltage and gpios,
> >> > has some risks and is not the shortest way to come closer.
> >> >
> >> > Thanks for your input.
> >> >
> >> > Cheers,
> >> > Hermann
> >> >
> >> >> dmesg:
> >> >>
> >> >> [ 9.829338] saa7130/34: v4l2 driver version 0.2.15 loaded
> >> >> [ 9.829408] saa7134 0000:00:08.0: PCI INT A -> GSI 17 (level, low)
> >> >> -> IRQ 17
> >> >> [ 9.829419] saa7130[0]: found at 0000:00:08.0, rev: 1, irq: 17,
> >> >> latency: 64, mmio: 0xfdffe000
> >> >> [ 9.829428] saa7130[0]: subsystem: 107d:6f3a, board:
> >> >> UNKNOWN/GENERIC [card=0,autodetected]
> >> >> [ 9.829458] saa7130[0]: board init: gpio is 6200c
> >> >> [ 9.829465] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on
> >> >> shared IRQs
> >> >> [ 9.980513] saa7130[0]: i2c eeprom 00: 7d 10 3a 6f 54 20 1c 00 43
> >> >> 43 a9 1c 55 d2 b2 92
> >> >> [ 9.980532] saa7130[0]: i2c eeprom 10: 0c ff 82 0e ff 20 ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980547] saa7130[0]: i2c eeprom 20: 01 40 02 03 03 02 01 03 08
> >> >> ff 00 8c ff ff ff ff
> >> >> [ 9.980562] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980578] saa7130[0]: i2c eeprom 40: 50 89 00 c2 00 00 02 30 02
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980593] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980608] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980623] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980639] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980654] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980670] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980685] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980701] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980716] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980731] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980747] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff
> >> >> ff ff ff ff ff ff ff
> >> >> [ 9.980876] saa7130[0]: registered device video0 [v4l2]
> >> >> [ 9.980908] saa7130[0]: registered device vbi0
> >> >>
> >> >>
> >> >> lsmod:
> >> >>
> >> >> saa7134 135552 0
> >> >> ir_common 47172 1 saa7134
> >> >> v4l2_common 14308 1 saa7134
> >> >> videodev 31040 2 saa7134,v4l2_common
> >> >> videobuf_dma_sg 11340 1 saa7134
> >> >> videobuf_core 16164 2 saa7134,videobuf_dma_sg
> >> >> tveeprom 10720 1 saa7134
> >> >> i2c_core 20844 4
> >> >> i2c_viapro,saa7134,v4l2_common,tveeprom
> >> >>
> >> >> lspci:
> >> >>
> >> >> 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130
> >> >> Video Broadcast Decoder [1131:7130] (rev 01)
> >> >> Subsystem: LeadTek Research Inc. Device [107d:6f3a]
> >> >> Flags: bus master, medium devsel, latency 64, IRQ 17
> >> >> Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
> >> >> Capabilities: [40] Power Management version 1
> >> >> Kernel driver in use: saa7134
> >> >> Kernel modules: saa7134
> >> >>
> >> >> Thanks again,
> >> >>
> >> >> Pavle.
> >> >>
> >> >>
> >> >>
> >> >>
> >> >>
> >> >> ______________________________________________________________________
> >> >> From: hermann pitton <hermann-pitton@arcor.de>
> >> >> To: Pavle Predic <pavle.predic@yahoo.co.uk>
> >> >> Cc: video4linux-list@redhat.com
> >> >> Sent: Sun, 8 November, 2009 23:35:08
> >> >> Subject: Re: Leadtek Winfast TV2100
> >> >>
> >> >> Hi Pavle,
> >> >>
> >> >> Am Sonntag, den 08.11.2009, 17:11 +0000 schrieb Pavle Predic:
> >> >> > Did anyone manage to get this card working on Linux? I got the
> >> >> picture out of the box, but it's impossible to get any sound from the
> >> >> damned thing. The card is not on CARDLIST.saa7134, but I assume a
> >> >> similar card/tuner combination can be used. But which? By the way, I
> >> >> got the speakers connected directly to card output, I'm not even
> >> >> trying to get it working with my sound card. I can hear clicks when
> >> >> loading/unloading modules, so it's alive but not set up properly.
> >> >> >
> >> >> > Any info would be greatly appreciated. Perhaps someone knows of
> >> >> another card that is similar to this one?
> >> >> >
> >> >> > Card info:
> >> >> > Chipset: saa7134
> >> >> > Tuner: Tvision TVF88T5-B/DFF
> >> >> > Card numbers that produce picture (modprobe saa7134 card=$n): 3, 7,
> >> >> 10, 16, 34, 35, 45, 46, 47, 48, 51, 63, 64, 68
> >> >>
> >> >> that is not enough information yet.
> >> >>
> >> >> The correct tuner for this one is tuner=69.
> >> >>
> >> >> Only with this one you will have also radio support.
> >> >>
> >> >> Since you mail from an UK mail provider, this tuner is not expected to
> >> >> work with PAL-I TV stereo sound there, but radio would work.
> >> >>
> >> >> Else, if neither amux = TV nor amux = LINE1 or LINE2 (LINE inputs for
> >> >> TV
> >> >> sound are only found on saa7130 chips, except there is also an extra
> >> >> TV
> >> >> mono section directly from the tuner) work for TV sound, most often
> >> >> an
> >> >> external audio mux is in the way and needs to be configured correctly
> >> >> with saa7134 gpio pins. Looking also at the minor chips on the card
> >> >> with
> >> >> more than 3 pins can reveal such a mux.
> >> >>
> >> >> There is also a software test on such hardware, succeeding in most
> >> >> cases.
> >> >>
> >> >> By default, external analog audio input is looped through to analog
> >> >> audio out, on which you are listening, if the driver is unloaded.
> >> >>
> >> >> On a saa7134 chip, on saa7130 are some known specials, you should hear
> >> >> the incoming sound directly on your headphones or what else you might
> >> >> be
> >> >> using directly connected to your card, trying on LINE1 and LINE2 for
> >> >> that.
> >> >>
> >> >> If not, you can expect that such a mux chip needs to be treated
> >> >> correctly.
> >> >>
> >> >> The DScaler (deinterlace.sf.net) regspy.exe often can help to identify
> >> >> such gpios in use, else you must trace lines and resistors on it.
> >> >>
> >> >> In general, an absolute minimum is to provide related "dmesg" after
> >> >> loading the driver _without_ having tried on other cards previously.
> >> >>
> >> >> Please read more on the linuxtv.org wiki about adding support for a
> >> >> new
> >> >> card.
> >> >>
> >> >> Cheers,
> >> >> Hermann
> >> >
> >> >
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-22 22:30 ` hermann pitton
@ 2009-11-23 1:23 ` Terry Wu
2009-11-23 1:42 ` Terry Wu
2009-11-23 1:47 ` hermann pitton
0 siblings, 2 replies; 12+ messages in thread
From: Terry Wu @ 2009-11-23 1:23 UTC (permalink / raw)
To: hermann pitton; +Cc: video4linux-list
[-- Attachment #1: Type: text/plain, Size: 26568 bytes --]
Hi,
The TVF88T5-BDFF data sheet is attached.
Terry Wu
11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
2009/11/23 hermann pitton <hermann-pitton@arcor.de>:
> Hi,
>
> Am Sonntag, den 22.11.2009, 20:51 +0800 schrieb Terry Wu:
>> Hi,
>>
>> I will give you the tuner data sheet and schematic of GPIO tomorrow.
>> Stay tuned.
>>
>> Terry
>
> that is of course very welcome.
>
> We know that the PLL chip is TI sn761677, datasheet is publicly
> available, radio switch is 0x11 and inside is a TENA tuner PCB also
> known from other tuners.
>
> For the gpio configuration hopefully my assumptions should not be that
> wrong.
>
> Pavle, are you able to test such yourself or should I provide some
> patches?
>
> Cheers,
> Hermann
>
>> 2009/11/22 <hermann-pitton@arcor.de>:
>> > Hi,
>> >
>> > sorry, posting from a webmail interface.
>> >
>> > Might get bounced from the list.
>> >
>> > ----- Original Nachricht ----
>> > Von: Pavle Predic <pavle.predic@yahoo.co.uk>
>> > An: Terry Wu <terrywu2009@gmail.com>, hermann pitton <hermann-pitton@arcor.de>
>> > Datum: 21.11.2009 20:53
>> > Betreff: Re: Leadtek Winfast TV2100
>> >
>> >> Hey Terry,
>> >>
>> >> Thanks for your input. Yes it would seem that my tuner is not supported
>> >> (it's a YMEC Tvision TVF88T5-B/DFF), and neither is my board. But I was
>> >> hoping that an existing board/tuner combination might do the job.
>> >>
>> >> @Hermann - I tried card IDs 1-150 with tuner=69 and - alas - didn't get
>> >> sound. Interestingly enough, almost all card ids produce a picture with this
>> >> tuner. Also, I noticed that with some board IDs I'm getting clicks when
>> >> muting/unmuting or switching channels, but no broadcast sound
>> >> whatsoever...:(
>> >
>> > Tuner=69 covers a lot of tuners with TexasInstruments pll chip, NTSC and PAL.
>> > I looked up this tuner from your previous mail and 69 is correct. You will note this when it comes to radio, UHF frequencies and takeover frequencies.
>> >
>> >> I also tried running regspy.exe (after booting to Windows) and performed the
>> >> test as described on dscaler site. But the results are way to cryptic for
>> >> me...I have no clue how to use this. So I'll paste it here, and maybe
>> >> someone will be able to draw a conclusion:
>> >>
>> > Ah, good.
>> >
>> >> SAA7130 Card [0]:
>> >>
>> >> Vendor ID: 0x1131
>> >> Device ID: 0x7130
>> >> Subsystem ID: 0x6f3a107d
>> >>
>> >>
>> >> 7 states dumped
>> >>
>> >> ----------------------------------------------------------------------------
>> >> ------
>> >>
>> >> SAA7130 Card - State 0:
>> >> SAA7134_GPIO_GPMODE: 80000009 * (10000000 00000000 00000000
>> >> 00001001)
>> >> SAA7134_GPIO_GPSTATUS: 0606200c * (00000110 00000110 00100000
>> >> 00001100)
>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>> >>
>> >> SAA7134_ANALOG_IO_SELECT: 3b * (00111011)
>> >>
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >>
>> >> Changes: State 0 -> State 1:
>> >> SAA7134_GPIO_GPMODE: 80000009 -> 8000000d (-------- --------
>> >> -------- -----0--)
>> >> SAA7134_GPIO_GPSTATUS: 0606200c -> 00062000 (-----11- --------
>> >> -------- ----11--)
>> >> SAA7134_ANALOG_IO_SELECT: 3b -> 00 (--111-11)
>> >>
>> >>
>> >> 3 changes
>> >>
>> >>
>> >> ----------------------------------------------------------------------------
>> >> ------
>> >>
>> >> SAA7130 Card - State 1:
>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> >> 00001101) (was: 80000009)
>> >> SAA7134_GPIO_GPSTATUS: 00062000 * (00000000 00000110 00100000
>> >> 00000000) (was: 0606200c)
>> >> SAA7134_ANALOG_IN_CTRL1: c1 * (11000001)
>> >>
>> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>> >> (was: 3b)
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >>
>> >> Changes: State 1 -> State 2:
>> >> SAA7134_GPIO_GPSTATUS: 00062000 -> 00062008 (-------- --------
>> >> -------- ----0---)
>> >> SAA7134_ANALOG_IN_CTRL1: c1 -> 83 (-1----0-)
>> >>
>> >> SAA7134_ANALOG_IO_SELECT: 00 -> 09 (----0--0)
>> >>
>> >>
>> >> 3 changes
>> >>
>> >>
>> >> ----------------------------------------------------------------------------
>> >> ------
>> >>
>> >> SAA7130 Card - State 2:
>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> >> 00001101)
>> >> SAA7134_GPIO_GPSTATUS: 00062008 (00000000 00000110 00100000
>> >> 00001000) (was: 00062000)
>> >> SAA7134_ANALOG_IN_CTRL1: 83 * (10000011)
>> >> (was: c1)
>> >> SAA7134_ANALOG_IO_SELECT: 09 (00001001)
>> >> (was: 00)
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >>
>> >> Changes: State 2 -> State 3:
>> >> SAA7134_ANALOG_IN_CTRL1: 83 -> c8 (-0--0-11)
>> >>
>> >>
>> >> 1 changes
>> >>
>> >>
>> >> ----------------------------------------------------------------------------
>> >> ------
>> >>
>> >> SAA7130 Card - State 3:
>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> >> 00001101)
>> >> SAA7134_GPIO_GPSTATUS: 00062008 * (00000000 00000110 00100000
>> >> 00001000)
>> >> SAA7134_ANALOG_IN_CTRL1: c8 * (11001000)
>> >> (was: 83)
>> >> SAA7134_ANALOG_IO_SELECT: 09 * (00001001)
>> >>
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >>
>> >> Changes: State 3 -> State 4:
>> >> SAA7134_GPIO_GPSTATUS: 00062008 -> 04062004 (-----0-- --------
>> >> -------- ----10--)
>> >> SAA7134_ANALOG_IN_CTRL1: c8 -> c1 (----1--0)
>> >> (same as 0, 1)
>> >> SAA7134_ANALOG_IO_SELECT: 09 -> 00 (----1--1)
>> >> (same as 1)
>> >>
>> >> 3 changes
>> >>
>> >>
>> >> ----------------------------------------------------------------------------
>> >> ------
>> >>
>> >> SAA7130 Card - State 4:
>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> >> 00001101)
>> >> SAA7134_GPIO_GPSTATUS: 04062004 * (00000100 00000110 00100000
>> >> 00000100) (was: 00062008)
>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>> >> (was: c8)
>> >> SAA7134_ANALOG_IO_SELECT: 00 (00000000)
>> >> (was: 09)
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >>
>> >> Changes: State 4 -> State 5:
>> >> SAA7134_GPIO_GPSTATUS: 04062004 -> 02062000 (-----10- --------
>> >> -------- -----1--)
>> >>
>> >> 1 changes
>> >>
>> >>
>> >> ----------------------------------------------------------------------------
>> >> ------
>> >>
>> >> SAA7130 Card - State 5:
>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> >> 00001101)
>> >> SAA7134_GPIO_GPSTATUS: 02062000 * (00000010 00000110 00100000
>> >> 00000000) (was: 04062004)
>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>> >>
>> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>> >>
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >>
>> >> Changes: State 5 -> Register Dump:
>> >> SAA7134_GPIO_GPSTATUS: 02062000 -> 06062008 (-----0-- --------
>> >> -------- ----0---)
>> >> SAA7134_ANALOG_IO_SELECT: 00 -> 02 (------0-)
>> >>
>> >>
>> >> 2 changes
>> >>
>> >>
>> >> ============================================================================
>> >> =====
>> >>
>> >> SAA7130 Card - Register Dump:
>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>> >> 00001101)
>> >> SAA7134_GPIO_GPSTATUS: 06062008 (00000110 00000110 00100000
>> >> 00001000) (was: 02062000)
>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>> >>
>> >> SAA7134_ANALOG_IO_SELECT: 02 (00000010)
>> >> (was: 00)
>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>> >> 00000000)
>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>> >>
>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>> >>
>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>> >>
>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>> >>
>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>> >>
>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>> >>
>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA0: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA1: 00 (00000000)
>> >>
>> >> SAA7134_TS_DMA2: 00 (00000000)
>> >>
>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>> >>
>> >>
>> >> end of dump
>> >>
>> >> Here is the order in which I performed the test:State 6
>> >> State 0 - viewing software off
>> >> State 1 - tuner mode
>> >> State 2 - composite mode
>> >> State 3 - s video mode
>> >> State 4 - radio mode
>> >> State 5 - tuner mode (again)
>> >> Final dump - viewing software off (again)
>> >>
>> >> Thanks to everyone for your help.
>> >>
>> >> Pavle.
>> >>
>> >
>> > Better don't top post. Becomes hard to read after a while.
>> >
>> > You would try wsith a gpio_mask = 0x0d.
>> >
>> > .gpio for TV is 0x00000000 (default, don't even need to set it).
>> >
>> > For s-video and composite 0x08.
>> >
>> > For radio 0x04.
>> >
>> > On saa7130 chips mono audio from tuner in most cases is connected to LINE2.
>> >
>> > Then also radio is on LINE2 and s-video and composite on LINE1.
>> >
>> > For .mute it seems to switch to s-video/composite LINE input and keeps that input open with .gpio 0x08.
>> >
>> > Maybe Terry knows better.
>> >
>> > Good luck for testing.
>> >
>> > Cheers,
>> > Hermann
>> >
>> >>
>> >> ________________________________
>> >> From: Terry Wu <terrywu2009@gmail.com>
>> >> To: hermann pitton <hermann-pitton@arcor.de>
>> >> Cc: Pavle Predic <pavle.predic@yahoo.co.uk>; video4linux-list@redhat.com
>> >> Sent: Sat, 21 November, 2009 10:07:05
>> >> Subject: Re: Leadtek Winfast TV2100
>> >>
>> >> Hi,
>> >>
>> >> There are many models of TV2100.
>> >> Different model uses different TV tuner.
>> >>
>> >> The tuner 69 is TUNER_TNF_5335MF.
>> >> Make sure the tuner in your TV2100 card is the TNF_5335MF.
>> >>
>> >> Maybe the tuner in your TV2100 card is not supported by current
>> >> v4l-dvb driver yet (linux\include\media\tuner.h).
>> >>
>> >>
>> >> Terry
>> >>
>> >> 2009/11/21 hermann pitton <hermann-pitton@arcor.de>:
>> >> > Hi Pavle,
>> >> >
>> >> > Am Freitag, den 20.11.2009, 14:11 +0000 schrieb Pavle Predic:
>> >> >> Hi Hermann,
>> >> >>
>> >> >> Thank you so much for your help. I didn't really get most of what you
>> >> >> said (way to technical for me), but at least I know now which tuner I
>> >> >> should use, so I'll keep testing with tuner 69 and see if I get
>> >> >> results.
>> >> >
>> >> > that one should be right, especially for analog radio.
>> >> >
>> >> >> BTW, I'm not from UK - I'm from Serbia and I'm trying to make the card
>> >> >> work for my cable tv which uses PAL BG (at least so they say).
>> >> >
>> >> > Lots of people are on the move these days, therefore it is important to
>> >> > know too, what they might carry with them. That tuner should be fine
>> >> > then.
>> >> >
>> >> >> I'll report back after testing on tuner 69 (I'll simply try all card
>> >> >> ids with this tuner id). In the meantime here's some more info:
>> >> >
>> >> > Better is to follow the advice how you can narrow down such stuff.
>> >> >
>> >> > As far I know, we have not destroyed a single device yet on the saa7134
>> >> > driver, but to go over all possibilities, concerning voltage and gpios,
>> >> > has some risks and is not the shortest way to come closer.
>> >> >
>> >> > Thanks for your input.
>> >> >
>> >> > Cheers,
>> >> > Hermann
>> >> >
>> >> >> dmesg:
>> >> >>
>> >> >> [ 9.829338] saa7130/34: v4l2 driver version 0.2.15 loaded
>> >> >> [ 9.829408] saa7134 0000:00:08.0: PCI INT A -> GSI 17 (level, low)
>> >> >> -> IRQ 17
>> >> >> [ 9.829419] saa7130[0]: found at 0000:00:08.0, rev: 1, irq: 17,
>> >> >> latency: 64, mmio: 0xfdffe000
>> >> >> [ 9.829428] saa7130[0]: subsystem: 107d:6f3a, board:
>> >> >> UNKNOWN/GENERIC [card=0,autodetected]
>> >> >> [ 9.829458] saa7130[0]: board init: gpio is 6200c
>> >> >> [ 9.829465] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on
>> >> >> shared IRQs
>> >> >> [ 9.980513] saa7130[0]: i2c eeprom 00: 7d 10 3a 6f 54 20 1c 00 43
>> >> >> 43 a9 1c 55 d2 b2 92
>> >> >> [ 9.980532] saa7130[0]: i2c eeprom 10: 0c ff 82 0e ff 20 ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980547] saa7130[0]: i2c eeprom 20: 01 40 02 03 03 02 01 03 08
>> >> >> ff 00 8c ff ff ff ff
>> >> >> [ 9.980562] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980578] saa7130[0]: i2c eeprom 40: 50 89 00 c2 00 00 02 30 02
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980593] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980608] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980623] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980639] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980654] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980670] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980685] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980701] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980716] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980731] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980747] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff
>> >> >> ff ff ff ff ff ff ff
>> >> >> [ 9.980876] saa7130[0]: registered device video0 [v4l2]
>> >> >> [ 9.980908] saa7130[0]: registered device vbi0
>> >> >>
>> >> >>
>> >> >> lsmod:
>> >> >>
>> >> >> saa7134 135552 0
>> >> >> ir_common 47172 1 saa7134
>> >> >> v4l2_common 14308 1 saa7134
>> >> >> videodev 31040 2 saa7134,v4l2_common
>> >> >> videobuf_dma_sg 11340 1 saa7134
>> >> >> videobuf_core 16164 2 saa7134,videobuf_dma_sg
>> >> >> tveeprom 10720 1 saa7134
>> >> >> i2c_core 20844 4
>> >> >> i2c_viapro,saa7134,v4l2_common,tveeprom
>> >> >>
>> >> >> lspci:
>> >> >>
>> >> >> 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130
>> >> >> Video Broadcast Decoder [1131:7130] (rev 01)
>> >> >> Subsystem: LeadTek Research Inc. Device [107d:6f3a]
>> >> >> Flags: bus master, medium devsel, latency 64, IRQ 17
>> >> >> Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
>> >> >> Capabilities: [40] Power Management version 1
>> >> >> Kernel driver in use: saa7134
>> >> >> Kernel modules: saa7134
>> >> >>
>> >> >> Thanks again,
>> >> >>
>> >> >> Pavle.
>> >> >>
>> >> >>
>> >> >>
>> >> >>
>> >> >>
>> >> >> ______________________________________________________________________
>> >> >> From: hermann pitton <hermann-pitton@arcor.de>
>> >> >> To: Pavle Predic <pavle.predic@yahoo.co.uk>
>> >> >> Cc: video4linux-list@redhat.com
>> >> >> Sent: Sun, 8 November, 2009 23:35:08
>> >> >> Subject: Re: Leadtek Winfast TV2100
>> >> >>
>> >> >> Hi Pavle,
>> >> >>
>> >> >> Am Sonntag, den 08.11.2009, 17:11 +0000 schrieb Pavle Predic:
>> >> >> > Did anyone manage to get this card working on Linux? I got the
>> >> >> picture out of the box, but it's impossible to get any sound from the
>> >> >> damned thing. The card is not on CARDLIST.saa7134, but I assume a
>> >> >> similar card/tuner combination can be used. But which? By the way, I
>> >> >> got the speakers connected directly to card output, I'm not even
>> >> >> trying to get it working with my sound card. I can hear clicks when
>> >> >> loading/unloading modules, so it's alive but not set up properly.
>> >> >> >
>> >> >> > Any info would be greatly appreciated. Perhaps someone knows of
>> >> >> another card that is similar to this one?
>> >> >> >
>> >> >> > Card info:
>> >> >> > Chipset: saa7134
>> >> >> > Tuner: Tvision TVF88T5-B/DFF
>> >> >> > Card numbers that produce picture (modprobe saa7134 card=$n): 3, 7,
>> >> >> 10, 16, 34, 35, 45, 46, 47, 48, 51, 63, 64, 68
>> >> >>
>> >> >> that is not enough information yet.
>> >> >>
>> >> >> The correct tuner for this one is tuner=69.
>> >> >>
>> >> >> Only with this one you will have also radio support.
>> >> >>
>> >> >> Since you mail from an UK mail provider, this tuner is not expected to
>> >> >> work with PAL-I TV stereo sound there, but radio would work.
>> >> >>
>> >> >> Else, if neither amux = TV nor amux = LINE1 or LINE2 (LINE inputs for
>> >> >> TV
>> >> >> sound are only found on saa7130 chips, except there is also an extra
>> >> >> TV
>> >> >> mono section directly from the tuner) work for TV sound, most often
>> >> >> an
>> >> >> external audio mux is in the way and needs to be configured correctly
>> >> >> with saa7134 gpio pins. Looking also at the minor chips on the card
>> >> >> with
>> >> >> more than 3 pins can reveal such a mux.
>> >> >>
>> >> >> There is also a software test on such hardware, succeeding in most
>> >> >> cases.
>> >> >>
>> >> >> By default, external analog audio input is looped through to analog
>> >> >> audio out, on which you are listening, if the driver is unloaded.
>> >> >>
>> >> >> On a saa7134 chip, on saa7130 are some known specials, you should hear
>> >> >> the incoming sound directly on your headphones or what else you might
>> >> >> be
>> >> >> using directly connected to your card, trying on LINE1 and LINE2 for
>> >> >> that.
>> >> >>
>> >> >> If not, you can expect that such a mux chip needs to be treated
>> >> >> correctly.
>> >> >>
>> >> >> The DScaler (deinterlace.sf.net) regspy.exe often can help to identify
>> >> >> such gpios in use, else you must trace lines and resistors on it.
>> >> >>
>> >> >> In general, an absolute minimum is to provide related "dmesg" after
>> >> >> loading the driver _without_ having tried on other cards previously.
>> >> >>
>> >> >> Please read more on the linuxtv.org wiki about adding support for a
>> >> >> new
>> >> >> card.
>> >> >>
>> >> >> Cheers,
>> >> >> Hermann
>> >> >
>> >> >
>
>
>
[-- Attachment #2: TVF88T5-BDFF.zip --]
[-- Type: application/zip, Size: 382169 bytes --]
[-- Attachment #3: Type: text/plain, Size: 164 bytes --]
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-23 1:23 ` Terry Wu
@ 2009-11-23 1:42 ` Terry Wu
2009-11-23 2:30 ` hermann pitton
2009-11-23 1:47 ` hermann pitton
1 sibling, 1 reply; 12+ messages in thread
From: Terry Wu @ 2009-11-23 1:42 UTC (permalink / raw)
To: hermann pitton; +Cc: video4linux-list
[-- Attachment #1: Type: text/plain, Size: 27552 bytes --]
Hi,
Please refer to the attached JPEG file for the GPIO settings of
TV2100 with FM (PCB:B).
Let me know if you need the information of TV2100 without FM
(PCB:A, TVF8533-BDF).
Terry Wu
2009/11/23 Terry Wu <terrywu2009@gmail.com>:
> Hi,
>
> The TVF88T5-BDFF data sheet is attached.
>
> Terry Wu
>
> 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
> 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
> 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
> 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
> 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
> 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
> 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
> 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
> 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
> 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
> 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
> 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
> 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
> 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
> 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
> 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
>
>
> 2009/11/23 hermann pitton <hermann-pitton@arcor.de>:
>> Hi,
>>
>> Am Sonntag, den 22.11.2009, 20:51 +0800 schrieb Terry Wu:
>>> Hi,
>>>
>>> I will give you the tuner data sheet and schematic of GPIO tomorrow.
>>> Stay tuned.
>>>
>>> Terry
>>
>> that is of course very welcome.
>>
>> We know that the PLL chip is TI sn761677, datasheet is publicly
>> available, radio switch is 0x11 and inside is a TENA tuner PCB also
>> known from other tuners.
>>
>> For the gpio configuration hopefully my assumptions should not be that
>> wrong.
>>
>> Pavle, are you able to test such yourself or should I provide some
>> patches?
>>
>> Cheers,
>> Hermann
>>
>>> 2009/11/22 <hermann-pitton@arcor.de>:
>>> > Hi,
>>> >
>>> > sorry, posting from a webmail interface.
>>> >
>>> > Might get bounced from the list.
>>> >
>>> > ----- Original Nachricht ----
>>> > Von: Pavle Predic <pavle.predic@yahoo.co.uk>
>>> > An: Terry Wu <terrywu2009@gmail.com>, hermann pitton <hermann-pitton@arcor.de>
>>> > Datum: 21.11.2009 20:53
>>> > Betreff: Re: Leadtek Winfast TV2100
>>> >
>>> >> Hey Terry,
>>> >>
>>> >> Thanks for your input. Yes it would seem that my tuner is not supported
>>> >> (it's a YMEC Tvision TVF88T5-B/DFF), and neither is my board. But I was
>>> >> hoping that an existing board/tuner combination might do the job.
>>> >>
>>> >> @Hermann - I tried card IDs 1-150 with tuner=69 and - alas - didn't get
>>> >> sound. Interestingly enough, almost all card ids produce a picture with this
>>> >> tuner. Also, I noticed that with some board IDs I'm getting clicks when
>>> >> muting/unmuting or switching channels, but no broadcast sound
>>> >> whatsoever...:(
>>> >
>>> > Tuner=69 covers a lot of tuners with TexasInstruments pll chip, NTSC and PAL.
>>> > I looked up this tuner from your previous mail and 69 is correct. You will note this when it comes to radio, UHF frequencies and takeover frequencies.
>>> >
>>> >> I also tried running regspy.exe (after booting to Windows) and performed the
>>> >> test as described on dscaler site. But the results are way to cryptic for
>>> >> me...I have no clue how to use this. So I'll paste it here, and maybe
>>> >> someone will be able to draw a conclusion:
>>> >>
>>> > Ah, good.
>>> >
>>> >> SAA7130 Card [0]:
>>> >>
>>> >> Vendor ID: 0x1131
>>> >> Device ID: 0x7130
>>> >> Subsystem ID: 0x6f3a107d
>>> >>
>>> >>
>>> >> 7 states dumped
>>> >>
>>> >> ----------------------------------------------------------------------------
>>> >> ------
>>> >>
>>> >> SAA7130 Card - State 0:
>>> >> SAA7134_GPIO_GPMODE: 80000009 * (10000000 00000000 00000000
>>> >> 00001001)
>>> >> SAA7134_GPIO_GPSTATUS: 0606200c * (00000110 00000110 00100000
>>> >> 00001100)
>>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>> >>
>>> >> SAA7134_ANALOG_IO_SELECT: 3b * (00111011)
>>> >>
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >>
>>> >> Changes: State 0 -> State 1:
>>> >> SAA7134_GPIO_GPMODE: 80000009 -> 8000000d (-------- --------
>>> >> -------- -----0--)
>>> >> SAA7134_GPIO_GPSTATUS: 0606200c -> 00062000 (-----11- --------
>>> >> -------- ----11--)
>>> >> SAA7134_ANALOG_IO_SELECT: 3b -> 00 (--111-11)
>>> >>
>>> >>
>>> >> 3 changes
>>> >>
>>> >>
>>> >> ----------------------------------------------------------------------------
>>> >> ------
>>> >>
>>> >> SAA7130 Card - State 1:
>>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>>> >> 00001101) (was: 80000009)
>>> >> SAA7134_GPIO_GPSTATUS: 00062000 * (00000000 00000110 00100000
>>> >> 00000000) (was: 0606200c)
>>> >> SAA7134_ANALOG_IN_CTRL1: c1 * (11000001)
>>> >>
>>> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>>> >> (was: 3b)
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >>
>>> >> Changes: State 1 -> State 2:
>>> >> SAA7134_GPIO_GPSTATUS: 00062000 -> 00062008 (-------- --------
>>> >> -------- ----0---)
>>> >> SAA7134_ANALOG_IN_CTRL1: c1 -> 83 (-1----0-)
>>> >>
>>> >> SAA7134_ANALOG_IO_SELECT: 00 -> 09 (----0--0)
>>> >>
>>> >>
>>> >> 3 changes
>>> >>
>>> >>
>>> >> ----------------------------------------------------------------------------
>>> >> ------
>>> >>
>>> >> SAA7130 Card - State 2:
>>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>>> >> 00001101)
>>> >> SAA7134_GPIO_GPSTATUS: 00062008 (00000000 00000110 00100000
>>> >> 00001000) (was: 00062000)
>>> >> SAA7134_ANALOG_IN_CTRL1: 83 * (10000011)
>>> >> (was: c1)
>>> >> SAA7134_ANALOG_IO_SELECT: 09 (00001001)
>>> >> (was: 00)
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >>
>>> >> Changes: State 2 -> State 3:
>>> >> SAA7134_ANALOG_IN_CTRL1: 83 -> c8 (-0--0-11)
>>> >>
>>> >>
>>> >> 1 changes
>>> >>
>>> >>
>>> >> ----------------------------------------------------------------------------
>>> >> ------
>>> >>
>>> >> SAA7130 Card - State 3:
>>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>>> >> 00001101)
>>> >> SAA7134_GPIO_GPSTATUS: 00062008 * (00000000 00000110 00100000
>>> >> 00001000)
>>> >> SAA7134_ANALOG_IN_CTRL1: c8 * (11001000)
>>> >> (was: 83)
>>> >> SAA7134_ANALOG_IO_SELECT: 09 * (00001001)
>>> >>
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >>
>>> >> Changes: State 3 -> State 4:
>>> >> SAA7134_GPIO_GPSTATUS: 00062008 -> 04062004 (-----0-- --------
>>> >> -------- ----10--)
>>> >> SAA7134_ANALOG_IN_CTRL1: c8 -> c1 (----1--0)
>>> >> (same as 0, 1)
>>> >> SAA7134_ANALOG_IO_SELECT: 09 -> 00 (----1--1)
>>> >> (same as 1)
>>> >>
>>> >> 3 changes
>>> >>
>>> >>
>>> >> ----------------------------------------------------------------------------
>>> >> ------
>>> >>
>>> >> SAA7130 Card - State 4:
>>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>>> >> 00001101)
>>> >> SAA7134_GPIO_GPSTATUS: 04062004 * (00000100 00000110 00100000
>>> >> 00000100) (was: 00062008)
>>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>> >> (was: c8)
>>> >> SAA7134_ANALOG_IO_SELECT: 00 (00000000)
>>> >> (was: 09)
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >>
>>> >> Changes: State 4 -> State 5:
>>> >> SAA7134_GPIO_GPSTATUS: 04062004 -> 02062000 (-----10- --------
>>> >> -------- -----1--)
>>> >>
>>> >> 1 changes
>>> >>
>>> >>
>>> >> ----------------------------------------------------------------------------
>>> >> ------
>>> >>
>>> >> SAA7130 Card - State 5:
>>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>>> >> 00001101)
>>> >> SAA7134_GPIO_GPSTATUS: 02062000 * (00000010 00000110 00100000
>>> >> 00000000) (was: 04062004)
>>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>> >>
>>> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
>>> >>
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >>
>>> >> Changes: State 5 -> Register Dump:
>>> >> SAA7134_GPIO_GPSTATUS: 02062000 -> 06062008 (-----0-- --------
>>> >> -------- ----0---)
>>> >> SAA7134_ANALOG_IO_SELECT: 00 -> 02 (------0-)
>>> >>
>>> >>
>>> >> 2 changes
>>> >>
>>> >>
>>> >> ============================================================================
>>> >> =====
>>> >>
>>> >> SAA7130 Card - Register Dump:
>>> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
>>> >> 00001101)
>>> >> SAA7134_GPIO_GPSTATUS: 06062008 (00000110 00000110 00100000
>>> >> 00001000) (was: 02062000)
>>> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
>>> >>
>>> >> SAA7134_ANALOG_IO_SELECT: 02 (00000010)
>>> >> (was: 00)
>>> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
>>> >> 00000000)
>>> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
>>> >>
>>> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
>>> >>
>>> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
>>> >>
>>> >> SAA7134_TS_PARALLEL: 04 (00000100)
>>> >>
>>> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_SERIAL1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA0: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA1: 00 (00000000)
>>> >>
>>> >> SAA7134_TS_DMA2: 00 (00000000)
>>> >>
>>> >> SAA7134_SPECIAL_MODE: 01 (00000001)
>>> >>
>>> >>
>>> >> end of dump
>>> >>
>>> >> Here is the order in which I performed the test:State 6
>>> >> State 0 - viewing software off
>>> >> State 1 - tuner mode
>>> >> State 2 - composite mode
>>> >> State 3 - s video mode
>>> >> State 4 - radio mode
>>> >> State 5 - tuner mode (again)
>>> >> Final dump - viewing software off (again)
>>> >>
>>> >> Thanks to everyone for your help.
>>> >>
>>> >> Pavle.
>>> >>
>>> >
>>> > Better don't top post. Becomes hard to read after a while.
>>> >
>>> > You would try wsith a gpio_mask = 0x0d.
>>> >
>>> > .gpio for TV is 0x00000000 (default, don't even need to set it).
>>> >
>>> > For s-video and composite 0x08.
>>> >
>>> > For radio 0x04.
>>> >
>>> > On saa7130 chips mono audio from tuner in most cases is connected to LINE2.
>>> >
>>> > Then also radio is on LINE2 and s-video and composite on LINE1.
>>> >
>>> > For .mute it seems to switch to s-video/composite LINE input and keeps that input open with .gpio 0x08.
>>> >
>>> > Maybe Terry knows better.
>>> >
>>> > Good luck for testing.
>>> >
>>> > Cheers,
>>> > Hermann
>>> >
>>> >>
>>> >> ________________________________
>>> >> From: Terry Wu <terrywu2009@gmail.com>
>>> >> To: hermann pitton <hermann-pitton@arcor.de>
>>> >> Cc: Pavle Predic <pavle.predic@yahoo.co.uk>; video4linux-list@redhat.com
>>> >> Sent: Sat, 21 November, 2009 10:07:05
>>> >> Subject: Re: Leadtek Winfast TV2100
>>> >>
>>> >> Hi,
>>> >>
>>> >> There are many models of TV2100.
>>> >> Different model uses different TV tuner.
>>> >>
>>> >> The tuner 69 is TUNER_TNF_5335MF.
>>> >> Make sure the tuner in your TV2100 card is the TNF_5335MF.
>>> >>
>>> >> Maybe the tuner in your TV2100 card is not supported by current
>>> >> v4l-dvb driver yet (linux\include\media\tuner.h).
>>> >>
>>> >>
>>> >> Terry
>>> >>
>>> >> 2009/11/21 hermann pitton <hermann-pitton@arcor.de>:
>>> >> > Hi Pavle,
>>> >> >
>>> >> > Am Freitag, den 20.11.2009, 14:11 +0000 schrieb Pavle Predic:
>>> >> >> Hi Hermann,
>>> >> >>
>>> >> >> Thank you so much for your help. I didn't really get most of what you
>>> >> >> said (way to technical for me), but at least I know now which tuner I
>>> >> >> should use, so I'll keep testing with tuner 69 and see if I get
>>> >> >> results.
>>> >> >
>>> >> > that one should be right, especially for analog radio.
>>> >> >
>>> >> >> BTW, I'm not from UK - I'm from Serbia and I'm trying to make the card
>>> >> >> work for my cable tv which uses PAL BG (at least so they say).
>>> >> >
>>> >> > Lots of people are on the move these days, therefore it is important to
>>> >> > know too, what they might carry with them. That tuner should be fine
>>> >> > then.
>>> >> >
>>> >> >> I'll report back after testing on tuner 69 (I'll simply try all card
>>> >> >> ids with this tuner id). In the meantime here's some more info:
>>> >> >
>>> >> > Better is to follow the advice how you can narrow down such stuff.
>>> >> >
>>> >> > As far I know, we have not destroyed a single device yet on the saa7134
>>> >> > driver, but to go over all possibilities, concerning voltage and gpios,
>>> >> > has some risks and is not the shortest way to come closer.
>>> >> >
>>> >> > Thanks for your input.
>>> >> >
>>> >> > Cheers,
>>> >> > Hermann
>>> >> >
>>> >> >> dmesg:
>>> >> >>
>>> >> >> [ 9.829338] saa7130/34: v4l2 driver version 0.2.15 loaded
>>> >> >> [ 9.829408] saa7134 0000:00:08.0: PCI INT A -> GSI 17 (level, low)
>>> >> >> -> IRQ 17
>>> >> >> [ 9.829419] saa7130[0]: found at 0000:00:08.0, rev: 1, irq: 17,
>>> >> >> latency: 64, mmio: 0xfdffe000
>>> >> >> [ 9.829428] saa7130[0]: subsystem: 107d:6f3a, board:
>>> >> >> UNKNOWN/GENERIC [card=0,autodetected]
>>> >> >> [ 9.829458] saa7130[0]: board init: gpio is 6200c
>>> >> >> [ 9.829465] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on
>>> >> >> shared IRQs
>>> >> >> [ 9.980513] saa7130[0]: i2c eeprom 00: 7d 10 3a 6f 54 20 1c 00 43
>>> >> >> 43 a9 1c 55 d2 b2 92
>>> >> >> [ 9.980532] saa7130[0]: i2c eeprom 10: 0c ff 82 0e ff 20 ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980547] saa7130[0]: i2c eeprom 20: 01 40 02 03 03 02 01 03 08
>>> >> >> ff 00 8c ff ff ff ff
>>> >> >> [ 9.980562] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980578] saa7130[0]: i2c eeprom 40: 50 89 00 c2 00 00 02 30 02
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980593] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980608] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980623] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980639] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980654] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980670] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980685] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980701] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980716] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980731] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980747] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff
>>> >> >> ff ff ff ff ff ff ff
>>> >> >> [ 9.980876] saa7130[0]: registered device video0 [v4l2]
>>> >> >> [ 9.980908] saa7130[0]: registered device vbi0
>>> >> >>
>>> >> >>
>>> >> >> lsmod:
>>> >> >>
>>> >> >> saa7134 135552 0
>>> >> >> ir_common 47172 1 saa7134
>>> >> >> v4l2_common 14308 1 saa7134
>>> >> >> videodev 31040 2 saa7134,v4l2_common
>>> >> >> videobuf_dma_sg 11340 1 saa7134
>>> >> >> videobuf_core 16164 2 saa7134,videobuf_dma_sg
>>> >> >> tveeprom 10720 1 saa7134
>>> >> >> i2c_core 20844 4
>>> >> >> i2c_viapro,saa7134,v4l2_common,tveeprom
>>> >> >>
>>> >> >> lspci:
>>> >> >>
>>> >> >> 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130
>>> >> >> Video Broadcast Decoder [1131:7130] (rev 01)
>>> >> >> Subsystem: LeadTek Research Inc. Device [107d:6f3a]
>>> >> >> Flags: bus master, medium devsel, latency 64, IRQ 17
>>> >> >> Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
>>> >> >> Capabilities: [40] Power Management version 1
>>> >> >> Kernel driver in use: saa7134
>>> >> >> Kernel modules: saa7134
>>> >> >>
>>> >> >> Thanks again,
>>> >> >>
>>> >> >> Pavle.
>>> >> >>
>>> >> >>
>>> >> >>
>>> >> >>
>>> >> >>
>>> >> >> ______________________________________________________________________
>>> >> >> From: hermann pitton <hermann-pitton@arcor.de>
>>> >> >> To: Pavle Predic <pavle.predic@yahoo.co.uk>
>>> >> >> Cc: video4linux-list@redhat.com
>>> >> >> Sent: Sun, 8 November, 2009 23:35:08
>>> >> >> Subject: Re: Leadtek Winfast TV2100
>>> >> >>
>>> >> >> Hi Pavle,
>>> >> >>
>>> >> >> Am Sonntag, den 08.11.2009, 17:11 +0000 schrieb Pavle Predic:
>>> >> >> > Did anyone manage to get this card working on Linux? I got the
>>> >> >> picture out of the box, but it's impossible to get any sound from the
>>> >> >> damned thing. The card is not on CARDLIST.saa7134, but I assume a
>>> >> >> similar card/tuner combination can be used. But which? By the way, I
>>> >> >> got the speakers connected directly to card output, I'm not even
>>> >> >> trying to get it working with my sound card. I can hear clicks when
>>> >> >> loading/unloading modules, so it's alive but not set up properly.
>>> >> >> >
>>> >> >> > Any info would be greatly appreciated. Perhaps someone knows of
>>> >> >> another card that is similar to this one?
>>> >> >> >
>>> >> >> > Card info:
>>> >> >> > Chipset: saa7134
>>> >> >> > Tuner: Tvision TVF88T5-B/DFF
>>> >> >> > Card numbers that produce picture (modprobe saa7134 card=$n): 3, 7,
>>> >> >> 10, 16, 34, 35, 45, 46, 47, 48, 51, 63, 64, 68
>>> >> >>
>>> >> >> that is not enough information yet.
>>> >> >>
>>> >> >> The correct tuner for this one is tuner=69.
>>> >> >>
>>> >> >> Only with this one you will have also radio support.
>>> >> >>
>>> >> >> Since you mail from an UK mail provider, this tuner is not expected to
>>> >> >> work with PAL-I TV stereo sound there, but radio would work.
>>> >> >>
>>> >> >> Else, if neither amux = TV nor amux = LINE1 or LINE2 (LINE inputs for
>>> >> >> TV
>>> >> >> sound are only found on saa7130 chips, except there is also an extra
>>> >> >> TV
>>> >> >> mono section directly from the tuner) work for TV sound, most often
>>> >> >> an
>>> >> >> external audio mux is in the way and needs to be configured correctly
>>> >> >> with saa7134 gpio pins. Looking also at the minor chips on the card
>>> >> >> with
>>> >> >> more than 3 pins can reveal such a mux.
>>> >> >>
>>> >> >> There is also a software test on such hardware, succeeding in most
>>> >> >> cases.
>>> >> >>
>>> >> >> By default, external analog audio input is looped through to analog
>>> >> >> audio out, on which you are listening, if the driver is unloaded.
>>> >> >>
>>> >> >> On a saa7134 chip, on saa7130 are some known specials, you should hear
>>> >> >> the incoming sound directly on your headphones or what else you might
>>> >> >> be
>>> >> >> using directly connected to your card, trying on LINE1 and LINE2 for
>>> >> >> that.
>>> >> >>
>>> >> >> If not, you can expect that such a mux chip needs to be treated
>>> >> >> correctly.
>>> >> >>
>>> >> >> The DScaler (deinterlace.sf.net) regspy.exe often can help to identify
>>> >> >> such gpios in use, else you must trace lines and resistors on it.
>>> >> >>
>>> >> >> In general, an absolute minimum is to provide related "dmesg" after
>>> >> >> loading the driver _without_ having tried on other cards previously.
>>> >> >>
>>> >> >> Please read more on the linuxtv.org wiki about adding support for a
>>> >> >> new
>>> >> >> card.
>>> >> >>
>>> >> >> Cheers,
>>> >> >> Hermann
>>> >> >
>>> >> >
>>
>>
>>
>
[-- Attachment #2: TV2100_with_FM_GPIO.jpg --]
[-- Type: image/jpeg, Size: 29516 bytes --]
[-- Attachment #3: Type: text/plain, Size: 164 bytes --]
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-23 1:23 ` Terry Wu
2009-11-23 1:42 ` Terry Wu
@ 2009-11-23 1:47 ` hermann pitton
1 sibling, 0 replies; 12+ messages in thread
From: hermann pitton @ 2009-11-23 1:47 UTC (permalink / raw)
To: Terry Wu; +Cc: video4linux-list
[-- Attachment #1: Type: text/plain, Size: 27451 bytes --]
Hi,
thanks!
Here is the TI PLL datasheet we walked
along.
Let's see, if we missed something.
Cheers,
Hermann
Am Montag, den 23.11.2009, 09:23 +0800 schrieb Terry Wu:
> Hi,
>
> The TVF88T5-BDFF data sheet is attached.
>
> Terry Wu
>
> 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
> 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
> 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
> 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
> 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
> 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
> 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
> 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
> 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
> 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
> 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
> 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
> 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
> 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
> 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
> 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
>
>
> 2009/11/23 hermann pitton <hermann-pitton@arcor.de>:
> > Hi,
> >
> > Am Sonntag, den 22.11.2009, 20:51 +0800 schrieb Terry Wu:
> >> Hi,
> >>
> >> I will give you the tuner data sheet and schematic of GPIO tomorrow.
> >> Stay tuned.
> >>
> >> Terry
> >
> > that is of course very welcome.
> >
> > We know that the PLL chip is TI sn761677, datasheet is publicly
> > available, radio switch is 0x11 and inside is a TENA tuner PCB also
> > known from other tuners.
> >
> > For the gpio configuration hopefully my assumptions should not be that
> > wrong.
> >
> > Pavle, are you able to test such yourself or should I provide some
> > patches?
> >
> > Cheers,
> > Hermann
> >
> >> 2009/11/22 <hermann-pitton@arcor.de>:
> >> > Hi,
> >> >
> >> > sorry, posting from a webmail interface.
> >> >
> >> > Might get bounced from the list.
> >> >
> >> > ----- Original Nachricht ----
> >> > Von: Pavle Predic <pavle.predic@yahoo.co.uk>
> >> > An: Terry Wu <terrywu2009@gmail.com>, hermann pitton <hermann-pitton@arcor.de>
> >> > Datum: 21.11.2009 20:53
> >> > Betreff: Re: Leadtek Winfast TV2100
> >> >
> >> >> Hey Terry,
> >> >>
> >> >> Thanks for your input. Yes it would seem that my tuner is not supported
> >> >> (it's a YMEC Tvision TVF88T5-B/DFF), and neither is my board. But I was
> >> >> hoping that an existing board/tuner combination might do the job.
> >> >>
> >> >> @Hermann - I tried card IDs 1-150 with tuner=69 and - alas - didn't get
> >> >> sound. Interestingly enough, almost all card ids produce a picture with this
> >> >> tuner. Also, I noticed that with some board IDs I'm getting clicks when
> >> >> muting/unmuting or switching channels, but no broadcast sound
> >> >> whatsoever...:(
> >> >
> >> > Tuner=69 covers a lot of tuners with TexasInstruments pll chip, NTSC and PAL.
> >> > I looked up this tuner from your previous mail and 69 is correct. You will note this when it comes to radio, UHF frequencies and takeover frequencies.
> >> >
> >> >> I also tried running regspy.exe (after booting to Windows) and performed the
> >> >> test as described on dscaler site. But the results are way to cryptic for
> >> >> me...I have no clue how to use this. So I'll paste it here, and maybe
> >> >> someone will be able to draw a conclusion:
> >> >>
> >> > Ah, good.
> >> >
> >> >> SAA7130 Card [0]:
> >> >>
> >> >> Vendor ID: 0x1131
> >> >> Device ID: 0x7130
> >> >> Subsystem ID: 0x6f3a107d
> >> >>
> >> >>
> >> >> 7 states dumped
> >> >>
> >> >> ----------------------------------------------------------------------------
> >> >> ------
> >> >>
> >> >> SAA7130 Card - State 0:
> >> >> SAA7134_GPIO_GPMODE: 80000009 * (10000000 00000000 00000000
> >> >> 00001001)
> >> >> SAA7134_GPIO_GPSTATUS: 0606200c * (00000110 00000110 00100000
> >> >> 00001100)
> >> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >> >>
> >> >> SAA7134_ANALOG_IO_SELECT: 3b * (00111011)
> >> >>
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >>
> >> >> Changes: State 0 -> State 1:
> >> >> SAA7134_GPIO_GPMODE: 80000009 -> 8000000d (-------- --------
> >> >> -------- -----0--)
> >> >> SAA7134_GPIO_GPSTATUS: 0606200c -> 00062000 (-----11- --------
> >> >> -------- ----11--)
> >> >> SAA7134_ANALOG_IO_SELECT: 3b -> 00 (--111-11)
> >> >>
> >> >>
> >> >> 3 changes
> >> >>
> >> >>
> >> >> ----------------------------------------------------------------------------
> >> >> ------
> >> >>
> >> >> SAA7130 Card - State 1:
> >> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> >> 00001101) (was: 80000009)
> >> >> SAA7134_GPIO_GPSTATUS: 00062000 * (00000000 00000110 00100000
> >> >> 00000000) (was: 0606200c)
> >> >> SAA7134_ANALOG_IN_CTRL1: c1 * (11000001)
> >> >>
> >> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
> >> >> (was: 3b)
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >>
> >> >> Changes: State 1 -> State 2:
> >> >> SAA7134_GPIO_GPSTATUS: 00062000 -> 00062008 (-------- --------
> >> >> -------- ----0---)
> >> >> SAA7134_ANALOG_IN_CTRL1: c1 -> 83 (-1----0-)
> >> >>
> >> >> SAA7134_ANALOG_IO_SELECT: 00 -> 09 (----0--0)
> >> >>
> >> >>
> >> >> 3 changes
> >> >>
> >> >>
> >> >> ----------------------------------------------------------------------------
> >> >> ------
> >> >>
> >> >> SAA7130 Card - State 2:
> >> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> >> 00001101)
> >> >> SAA7134_GPIO_GPSTATUS: 00062008 (00000000 00000110 00100000
> >> >> 00001000) (was: 00062000)
> >> >> SAA7134_ANALOG_IN_CTRL1: 83 * (10000011)
> >> >> (was: c1)
> >> >> SAA7134_ANALOG_IO_SELECT: 09 (00001001)
> >> >> (was: 00)
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >>
> >> >> Changes: State 2 -> State 3:
> >> >> SAA7134_ANALOG_IN_CTRL1: 83 -> c8 (-0--0-11)
> >> >>
> >> >>
> >> >> 1 changes
> >> >>
> >> >>
> >> >> ----------------------------------------------------------------------------
> >> >> ------
> >> >>
> >> >> SAA7130 Card - State 3:
> >> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> >> 00001101)
> >> >> SAA7134_GPIO_GPSTATUS: 00062008 * (00000000 00000110 00100000
> >> >> 00001000)
> >> >> SAA7134_ANALOG_IN_CTRL1: c8 * (11001000)
> >> >> (was: 83)
> >> >> SAA7134_ANALOG_IO_SELECT: 09 * (00001001)
> >> >>
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >>
> >> >> Changes: State 3 -> State 4:
> >> >> SAA7134_GPIO_GPSTATUS: 00062008 -> 04062004 (-----0-- --------
> >> >> -------- ----10--)
> >> >> SAA7134_ANALOG_IN_CTRL1: c8 -> c1 (----1--0)
> >> >> (same as 0, 1)
> >> >> SAA7134_ANALOG_IO_SELECT: 09 -> 00 (----1--1)
> >> >> (same as 1)
> >> >>
> >> >> 3 changes
> >> >>
> >> >>
> >> >> ----------------------------------------------------------------------------
> >> >> ------
> >> >>
> >> >> SAA7130 Card - State 4:
> >> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> >> 00001101)
> >> >> SAA7134_GPIO_GPSTATUS: 04062004 * (00000100 00000110 00100000
> >> >> 00000100) (was: 00062008)
> >> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >> >> (was: c8)
> >> >> SAA7134_ANALOG_IO_SELECT: 00 (00000000)
> >> >> (was: 09)
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >>
> >> >> Changes: State 4 -> State 5:
> >> >> SAA7134_GPIO_GPSTATUS: 04062004 -> 02062000 (-----10- --------
> >> >> -------- -----1--)
> >> >>
> >> >> 1 changes
> >> >>
> >> >>
> >> >> ----------------------------------------------------------------------------
> >> >> ------
> >> >>
> >> >> SAA7130 Card - State 5:
> >> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> >> 00001101)
> >> >> SAA7134_GPIO_GPSTATUS: 02062000 * (00000010 00000110 00100000
> >> >> 00000000) (was: 04062004)
> >> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >> >>
> >> >> SAA7134_ANALOG_IO_SELECT: 00 * (00000000)
> >> >>
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >>
> >> >> Changes: State 5 -> Register Dump:
> >> >> SAA7134_GPIO_GPSTATUS: 02062000 -> 06062008 (-----0-- --------
> >> >> -------- ----0---)
> >> >> SAA7134_ANALOG_IO_SELECT: 00 -> 02 (------0-)
> >> >>
> >> >>
> >> >> 2 changes
> >> >>
> >> >>
> >> >> ============================================================================
> >> >> =====
> >> >>
> >> >> SAA7130 Card - Register Dump:
> >> >> SAA7134_GPIO_GPMODE: 8000000d (10000000 00000000 00000000
> >> >> 00001101)
> >> >> SAA7134_GPIO_GPSTATUS: 06062008 (00000110 00000110 00100000
> >> >> 00001000) (was: 02062000)
> >> >> SAA7134_ANALOG_IN_CTRL1: c1 (11000001)
> >> >>
> >> >> SAA7134_ANALOG_IO_SELECT: 02 (00000010)
> >> >> (was: 00)
> >> >> SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
> >> >> 00000000)
> >> >> SAA7134_VIDEO_PORT_CTRL8: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_SELECT: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_FORMAT: 01 (00000001)
> >> >>
> >> >> SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000)
> >> >>
> >> >> SAA7134_I2S_AUDIO_OUTPUT: 01 (00000001)
> >> >>
> >> >> SAA7134_TS_PARALLEL: 04 (00000100)
> >> >>
> >> >> SAA7134_TS_PARALLEL_SERIAL: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_SERIAL1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA0: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA1: 00 (00000000)
> >> >>
> >> >> SAA7134_TS_DMA2: 00 (00000000)
> >> >>
> >> >> SAA7134_SPECIAL_MODE: 01 (00000001)
> >> >>
> >> >>
> >> >> end of dump
> >> >>
> >> >> Here is the order in which I performed the test:State 6
> >> >> State 0 - viewing software off
> >> >> State 1 - tuner mode
> >> >> State 2 - composite mode
> >> >> State 3 - s video mode
> >> >> State 4 - radio mode
> >> >> State 5 - tuner mode (again)
> >> >> Final dump - viewing software off (again)
> >> >>
> >> >> Thanks to everyone for your help.
> >> >>
> >> >> Pavle.
> >> >>
> >> >
> >> > Better don't top post. Becomes hard to read after a while.
> >> >
> >> > You would try wsith a gpio_mask = 0x0d.
> >> >
> >> > .gpio for TV is 0x00000000 (default, don't even need to set it).
> >> >
> >> > For s-video and composite 0x08.
> >> >
> >> > For radio 0x04.
> >> >
> >> > On saa7130 chips mono audio from tuner in most cases is connected to LINE2.
> >> >
> >> > Then also radio is on LINE2 and s-video and composite on LINE1.
> >> >
> >> > For .mute it seems to switch to s-video/composite LINE input and keeps that input open with .gpio 0x08.
> >> >
> >> > Maybe Terry knows better.
> >> >
> >> > Good luck for testing.
> >> >
> >> > Cheers,
> >> > Hermann
> >> >
> >> >>
> >> >> ________________________________
> >> >> From: Terry Wu <terrywu2009@gmail.com>
> >> >> To: hermann pitton <hermann-pitton@arcor.de>
> >> >> Cc: Pavle Predic <pavle.predic@yahoo.co.uk>; video4linux-list@redhat.com
> >> >> Sent: Sat, 21 November, 2009 10:07:05
> >> >> Subject: Re: Leadtek Winfast TV2100
> >> >>
> >> >> Hi,
> >> >>
> >> >> There are many models of TV2100.
> >> >> Different model uses different TV tuner.
> >> >>
> >> >> The tuner 69 is TUNER_TNF_5335MF.
> >> >> Make sure the tuner in your TV2100 card is the TNF_5335MF.
> >> >>
> >> >> Maybe the tuner in your TV2100 card is not supported by current
> >> >> v4l-dvb driver yet (linux\include\media\tuner.h).
> >> >>
> >> >>
> >> >> Terry
> >> >>
> >> >> 2009/11/21 hermann pitton <hermann-pitton@arcor.de>:
> >> >> > Hi Pavle,
> >> >> >
> >> >> > Am Freitag, den 20.11.2009, 14:11 +0000 schrieb Pavle Predic:
> >> >> >> Hi Hermann,
> >> >> >>
> >> >> >> Thank you so much for your help. I didn't really get most of what you
> >> >> >> said (way to technical for me), but at least I know now which tuner I
> >> >> >> should use, so I'll keep testing with tuner 69 and see if I get
> >> >> >> results.
> >> >> >
> >> >> > that one should be right, especially for analog radio.
> >> >> >
> >> >> >> BTW, I'm not from UK - I'm from Serbia and I'm trying to make the card
> >> >> >> work for my cable tv which uses PAL BG (at least so they say).
> >> >> >
> >> >> > Lots of people are on the move these days, therefore it is important to
> >> >> > know too, what they might carry with them. That tuner should be fine
> >> >> > then.
> >> >> >
> >> >> >> I'll report back after testing on tuner 69 (I'll simply try all card
> >> >> >> ids with this tuner id). In the meantime here's some more info:
> >> >> >
> >> >> > Better is to follow the advice how you can narrow down such stuff.
> >> >> >
> >> >> > As far I know, we have not destroyed a single device yet on the saa7134
> >> >> > driver, but to go over all possibilities, concerning voltage and gpios,
> >> >> > has some risks and is not the shortest way to come closer.
> >> >> >
> >> >> > Thanks for your input.
> >> >> >
> >> >> > Cheers,
> >> >> > Hermann
> >> >> >
> >> >> >> dmesg:
> >> >> >>
> >> >> >> [ 9.829338] saa7130/34: v4l2 driver version 0.2.15 loaded
> >> >> >> [ 9.829408] saa7134 0000:00:08.0: PCI INT A -> GSI 17 (level, low)
> >> >> >> -> IRQ 17
> >> >> >> [ 9.829419] saa7130[0]: found at 0000:00:08.0, rev: 1, irq: 17,
> >> >> >> latency: 64, mmio: 0xfdffe000
> >> >> >> [ 9.829428] saa7130[0]: subsystem: 107d:6f3a, board:
> >> >> >> UNKNOWN/GENERIC [card=0,autodetected]
> >> >> >> [ 9.829458] saa7130[0]: board init: gpio is 6200c
> >> >> >> [ 9.829465] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on
> >> >> >> shared IRQs
> >> >> >> [ 9.980513] saa7130[0]: i2c eeprom 00: 7d 10 3a 6f 54 20 1c 00 43
> >> >> >> 43 a9 1c 55 d2 b2 92
> >> >> >> [ 9.980532] saa7130[0]: i2c eeprom 10: 0c ff 82 0e ff 20 ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980547] saa7130[0]: i2c eeprom 20: 01 40 02 03 03 02 01 03 08
> >> >> >> ff 00 8c ff ff ff ff
> >> >> >> [ 9.980562] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980578] saa7130[0]: i2c eeprom 40: 50 89 00 c2 00 00 02 30 02
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980593] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980608] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980623] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980639] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980654] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980670] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980685] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980701] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980716] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980731] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980747] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff
> >> >> >> ff ff ff ff ff ff ff
> >> >> >> [ 9.980876] saa7130[0]: registered device video0 [v4l2]
> >> >> >> [ 9.980908] saa7130[0]: registered device vbi0
> >> >> >>
> >> >> >>
> >> >> >> lsmod:
> >> >> >>
> >> >> >> saa7134 135552 0
> >> >> >> ir_common 47172 1 saa7134
> >> >> >> v4l2_common 14308 1 saa7134
> >> >> >> videodev 31040 2 saa7134,v4l2_common
> >> >> >> videobuf_dma_sg 11340 1 saa7134
> >> >> >> videobuf_core 16164 2 saa7134,videobuf_dma_sg
> >> >> >> tveeprom 10720 1 saa7134
> >> >> >> i2c_core 20844 4
> >> >> >> i2c_viapro,saa7134,v4l2_common,tveeprom
> >> >> >>
> >> >> >> lspci:
> >> >> >>
> >> >> >> 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130
> >> >> >> Video Broadcast Decoder [1131:7130] (rev 01)
> >> >> >> Subsystem: LeadTek Research Inc. Device [107d:6f3a]
> >> >> >> Flags: bus master, medium devsel, latency 64, IRQ 17
> >> >> >> Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
> >> >> >> Capabilities: [40] Power Management version 1
> >> >> >> Kernel driver in use: saa7134
> >> >> >> Kernel modules: saa7134
> >> >> >>
> >> >> >> Thanks again,
> >> >> >>
> >> >> >> Pavle.
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> >> ______________________________________________________________________
> >> >> >> From: hermann pitton <hermann-pitton@arcor.de>
> >> >> >> To: Pavle Predic <pavle.predic@yahoo.co.uk>
> >> >> >> Cc: video4linux-list@redhat.com
> >> >> >> Sent: Sun, 8 November, 2009 23:35:08
> >> >> >> Subject: Re: Leadtek Winfast TV2100
> >> >> >>
> >> >> >> Hi Pavle,
> >> >> >>
> >> >> >> Am Sonntag, den 08.11.2009, 17:11 +0000 schrieb Pavle Predic:
> >> >> >> > Did anyone manage to get this card working on Linux? I got the
> >> >> >> picture out of the box, but it's impossible to get any sound from the
> >> >> >> damned thing. The card is not on CARDLIST.saa7134, but I assume a
> >> >> >> similar card/tuner combination can be used. But which? By the way, I
> >> >> >> got the speakers connected directly to card output, I'm not even
> >> >> >> trying to get it working with my sound card. I can hear clicks when
> >> >> >> loading/unloading modules, so it's alive but not set up properly.
> >> >> >> >
> >> >> >> > Any info would be greatly appreciated. Perhaps someone knows of
> >> >> >> another card that is similar to this one?
> >> >> >> >
> >> >> >> > Card info:
> >> >> >> > Chipset: saa7134
> >> >> >> > Tuner: Tvision TVF88T5-B/DFF
> >> >> >> > Card numbers that produce picture (modprobe saa7134 card=$n): 3, 7,
> >> >> >> 10, 16, 34, 35, 45, 46, 47, 48, 51, 63, 64, 68
> >> >> >>
> >> >> >> that is not enough information yet.
> >> >> >>
> >> >> >> The correct tuner for this one is tuner=69.
> >> >> >>
> >> >> >> Only with this one you will have also radio support.
> >> >> >>
> >> >> >> Since you mail from an UK mail provider, this tuner is not expected to
> >> >> >> work with PAL-I TV stereo sound there, but radio would work.
> >> >> >>
> >> >> >> Else, if neither amux = TV nor amux = LINE1 or LINE2 (LINE inputs for
> >> >> >> TV
> >> >> >> sound are only found on saa7130 chips, except there is also an extra
> >> >> >> TV
> >> >> >> mono section directly from the tuner) work for TV sound, most often
> >> >> >> an
> >> >> >> external audio mux is in the way and needs to be configured correctly
> >> >> >> with saa7134 gpio pins. Looking also at the minor chips on the card
> >> >> >> with
> >> >> >> more than 3 pins can reveal such a mux.
> >> >> >>
> >> >> >> There is also a software test on such hardware, succeeding in most
> >> >> >> cases.
> >> >> >>
> >> >> >> By default, external analog audio input is looped through to analog
> >> >> >> audio out, on which you are listening, if the driver is unloaded.
> >> >> >>
> >> >> >> On a saa7134 chip, on saa7130 are some known specials, you should hear
> >> >> >> the incoming sound directly on your headphones or what else you might
> >> >> >> be
> >> >> >> using directly connected to your card, trying on LINE1 and LINE2 for
> >> >> >> that.
> >> >> >>
> >> >> >> If not, you can expect that such a mux chip needs to be treated
> >> >> >> correctly.
> >> >> >>
> >> >> >> The DScaler (deinterlace.sf.net) regspy.exe often can help to identify
> >> >> >> such gpios in use, else you must trace lines and resistors on it.
> >> >> >>
> >> >> >> In general, an absolute minimum is to provide related "dmesg" after
> >> >> >> loading the driver _without_ having tried on other cards previously.
> >> >> >>
> >> >> >> Please read more on the linuxtv.org wiki about adding support for a
> >> >> >> new
> >> >> >> card.
> >> >> >>
> >> >> >> Cheers,
> >> >> >> Hermann
> >> >> >
> >> >> >
> >
> >
> >
[-- Attachment #2: sn761677.pdf --]
[-- Type: application/pdf, Size: 202723 bytes --]
[-- Attachment #3: Type: text/plain, Size: 164 bytes --]
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-23 1:42 ` Terry Wu
@ 2009-11-23 2:30 ` hermann pitton
2009-11-26 2:33 ` Terry Wu
0 siblings, 1 reply; 12+ messages in thread
From: hermann pitton @ 2009-11-23 2:30 UTC (permalink / raw)
To: Terry Wu; +Cc: video4linux-list
Hi, thanks again!
Am Montag, den 23.11.2009, 09:42 +0800 schrieb Terry Wu:
> Hi,
>
> Please refer to the attached JPEG file for the GPIO settings of
> TV2100 with FM (PCB:B).
>
> Let me know if you need the information of TV2100 without FM
> (PCB:A, TVF8533-BDF).
>
> Terry Wu
On a first look, if we start to count gpios from zero, we tell the same.
The TVF8533_BDF I would have to look up. It is four to five years back.
If it uses that minor number TI chip without radio support, we treat it
as tuner=69 too currently.
For all such older can tuners, widely different about the globe, counts,
that we don't have any way to detect them. So first working, either NTSC
or PAL, sits in the pool position and others have to think twice.
OEMs do code tuners into eeprom content, some do not at all, such doing
it are in competition and don't follow the rules of the main chip
manufacturer, Philips/NXP in that case, and go their own ways.
So tuner tables are unstable across manufacturers.
We often can't help that much in such cases, but implementing their own
tuner eeprom detection into the linux drivers is of course still
welcome. Hauppauge does it very successfully since years.
We can't do much about it, if OEMs don't follow Philips or whom ever on
such.
Thanks,
Hermann
>
> 2009/11/23 Terry Wu <terrywu2009@gmail.com>:
> > Hi,
> >
> > The TVF88T5-BDFF data sheet is attached.
> >
> > Terry Wu
> >
> > 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
> > 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
> > 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
> > 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
> > 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
> > 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
> > 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
> > 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
> > 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
> > 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
> > 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
> > 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
> > 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
> > 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
> > 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
> > 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
> >
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-23 2:30 ` hermann pitton
@ 2009-11-26 2:33 ` Terry Wu
2009-11-28 3:09 ` hermann pitton
0 siblings, 1 reply; 12+ messages in thread
From: Terry Wu @ 2009-11-26 2:33 UTC (permalink / raw)
To: hermann pitton; +Cc: video4linux-list
Hi,
Here are the subsystem IDs for different TV2100 models:
Subsystem ID:0x6f30107d, TVF8533-BDF (PAL BG/DK)
Subsystem ID:0x6f32107d, TVF5533-MF (NTSC)
Subsystem ID:0x6f3a107d, TVF88T5-B/DFF (PAL BG/DK, FM)
Terry
2009/11/23 hermann pitton <hermann-pitton@arcor.de>:
> Hi, thanks again!
>
> Am Montag, den 23.11.2009, 09:42 +0800 schrieb Terry Wu:
>> Hi,
>>
>> Please refer to the attached JPEG file for the GPIO settings of
>> TV2100 with FM (PCB:B).
>>
>> Let me know if you need the information of TV2100 without FM
>> (PCB:A, TVF8533-BDF).
>>
>> Terry Wu
>
> On a first look, if we start to count gpios from zero, we tell the same.
>
> The TVF8533_BDF I would have to look up. It is four to five years back.
>
> If it uses that minor number TI chip without radio support, we treat it
> as tuner=69 too currently.
>
> For all such older can tuners, widely different about the globe, counts,
> that we don't have any way to detect them. So first working, either NTSC
> or PAL, sits in the pool position and others have to think twice.
>
> OEMs do code tuners into eeprom content, some do not at all, such doing
> it are in competition and don't follow the rules of the main chip
> manufacturer, Philips/NXP in that case, and go their own ways.
>
> So tuner tables are unstable across manufacturers.
>
> We often can't help that much in such cases, but implementing their own
> tuner eeprom detection into the linux drivers is of course still
> welcome. Hauppauge does it very successfully since years.
>
> We can't do much about it, if OEMs don't follow Philips or whom ever on
> such.
>
> Thanks,
> Hermann
>
>
>>
>> 2009/11/23 Terry Wu <terrywu2009@gmail.com>:
>> > Hi,
>> >
>> > The TVF88T5-BDFF data sheet is attached.
>> >
>> > Terry Wu
>> >
>> > 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
>> > 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
>> > 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
>> > 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
>> > 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
>> > 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
>> > 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
>> > 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
>> > 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
>> > 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
>> > 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
>> > 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
>> > 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
>> > 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
>> > 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
>> > 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
>> >
>
>
>
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-26 2:33 ` Terry Wu
@ 2009-11-28 3:09 ` hermann pitton
2009-11-28 18:04 ` Pavle Predic
0 siblings, 1 reply; 12+ messages in thread
From: hermann pitton @ 2009-11-28 3:09 UTC (permalink / raw)
To: Terry Wu; +Cc: video4linux-list
Hi Terry Wu,
Am Donnerstag, den 26.11.2009, 10:33 +0800 schrieb Terry Wu:
> Hi,
>
> Here are the subsystem IDs for different TV2100 models:
> Subsystem ID:0x6f30107d, TVF8533-BDF (PAL BG/DK)
> Subsystem ID:0x6f32107d, TVF5533-MF (NTSC)
> Subsystem ID:0x6f3a107d, TVF88T5-B/DFF (PAL BG/DK, FM)
>
> Terry
better is to become active on it.
we can most likely help about how to match such tuners fine,
if any doubts left, but the best is to send just patches with having
such hardware to test on.
Compared to the early tda9887 stuff on LeadTek devices, LeadTek was
pioneering and we have that in mind, it should be fairly easy for those.
Let's know the other way round too, where you have still concerns doing
so.
Cheers,
Hermann
> 2009/11/23 hermann pitton <hermann-pitton@arcor.de>:
> > Hi, thanks again!
> >
> > Am Montag, den 23.11.2009, 09:42 +0800 schrieb Terry Wu:
> >> Hi,
> >>
> >> Please refer to the attached JPEG file for the GPIO settings of
> >> TV2100 with FM (PCB:B).
> >>
> >> Let me know if you need the information of TV2100 without FM
> >> (PCB:A, TVF8533-BDF).
> >>
> >> Terry Wu
> >
> > On a first look, if we start to count gpios from zero, we tell the same.
> >
> > The TVF8533_BDF I would have to look up. It is four to five years back.
> >
> > If it uses that minor number TI chip without radio support, we treat it
> > as tuner=69 too currently.
> >
> > For all such older can tuners, widely different about the globe, counts,
> > that we don't have any way to detect them. So first working, either NTSC
> > or PAL, sits in the pool position and others have to think twice.
> >
> > OEMs do code tuners into eeprom content, some do not at all, such doing
> > it are in competition and don't follow the rules of the main chip
> > manufacturer, Philips/NXP in that case, and go their own ways.
> >
> > So tuner tables are unstable across manufacturers.
> >
> > We often can't help that much in such cases, but implementing their own
> > tuner eeprom detection into the linux drivers is of course still
> > welcome. Hauppauge does it very successfully since years.
> >
> > We can't do much about it, if OEMs don't follow Philips or whom ever on
> > such.
> >
> > Thanks,
> > Hermann
> >
> >
> >>
> >> 2009/11/23 Terry Wu <terrywu2009@gmail.com>:
> >> > Hi,
> >> >
> >> > The TVF88T5-BDFF data sheet is attached.
> >> >
> >> > Terry Wu
> >> >
> >> > 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
> >> > 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
> >> > 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
> >> > 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
> >> > 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
> >> > 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
> >> > 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
> >> > 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
> >> > 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
> >> > 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
> >> > 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
> >> > 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
> >> > 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
> >> > 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
> >> > 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
> >> > 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
> >> >
> >
> >
> >
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2009-11-28 3:09 ` hermann pitton
@ 2009-11-28 18:04 ` Pavle Predic
0 siblings, 0 replies; 12+ messages in thread
From: Pavle Predic @ 2009-11-28 18:04 UTC (permalink / raw)
To: hermann pitton, Terry Wu; +Cc: video4linux-list
Hey guys,
Let me start by thanking you both for all your help. Unfortunately, there isn't much I can do with the data you provided - it's way too technical for me. I'd be happy to do any tests and apply any patches, but I would need some instructions - but only if you have time; I really don't want to burden you with this.
Thanks again,
Pavle.
________________________________
From: hermann pitton <hermann-pitton@arcor.de>
To: Terry Wu <terrywu2009@gmail.com>
Cc: pavle.predic@yahoo.co.uk; video4linux-list@redhat.com
Sent: Sat, 28 November, 2009 4:09:28
Subject: Re: Re: Leadtek Winfast TV2100
Hi Terry Wu,
Am Donnerstag, den 26.11.2009, 10:33 +0800 schrieb Terry Wu:
> Hi,
>
> Here are the subsystem IDs for different TV2100 models:
> Subsystem ID:0x6f30107d, TVF8533-BDF (PAL BG/DK)
> Subsystem ID:0x6f32107d, TVF5533-MF (NTSC)
> Subsystem ID:0x6f3a107d, TVF88T5-B/DFF (PAL BG/DK, FM)
>
> Terry
better is to become active on it.
we can most likely help about how to match such tuners fine,
if any doubts left, but the best is to send just patches with having
such hardware to test on.
Compared to the early tda9887 stuff on LeadTek devices, LeadTek was
pioneering and we have that in mind, it should be fairly easy for those.
Let's know the other way round too, where you have still concerns doing
so.
Cheers,
Hermann
> 2009/11/23 hermann pitton <hermann-pitton@arcor.de>:
> > Hi, thanks again!
> >
> > Am Montag, den 23.11.2009, 09:42 +0800 schrieb Terry Wu:
> >> Hi,
> >>
> >> Please refer to the attached JPEG file for the GPIO settings of
> >> TV2100 with FM (PCB:B).
> >>
> >> Let me know if you need the information of TV2100 without FM
> >> (PCB:A, TVF8533-BDF).
> >>
> >> Terry Wu
> >
> > On a first look, if we start to count gpios from zero, we tell the same.
> >
> > The TVF8533_BDF I would have to look up. It is four to five years back.
> >
> > If it uses that minor number TI chip without radio support, we treat it
> > as tuner=69 too currently.
> >
> > For all such older can tuners, widely different about the globe, counts,
> > that we don't have any way to detect them. So first working, either NTSC
> > or PAL, sits in the pool position and others have to think twice.
> >
> > OEMs do code tuners into eeprom content, some do not at all, such doing
> > it are in competition and don't follow the rules of the main chip
> > manufacturer, Philips/NXP in that case, and go their own ways.
> >
> > So tuner tables are unstable across manufacturers.
> >
> > We often can't help that much in such cases, but implementing their own
> > tuner eeprom detection into the linux drivers is of course still
> > welcome. Hauppauge does it very successfully since years.
> >
> > We can't do much about it, if OEMs don't follow Philips or whom ever on
> > such.
> >
> > Thanks,
> > Hermann
> >
> >
> >>
> >> 2009/11/23 Terry Wu <terrywu2009@gmail.com>:
> >> > Hi,
> >> >
> >> > The TVF88T5-BDFF data sheet is attached.
> >> >
> >> > Terry Wu
> >> >
> >> > 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
> >> > 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
> >> > 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
> >> > 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
> >> > 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
> >> > 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
> >> > 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
> >> > 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
> >> > 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
> >> > 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
> >> > 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
> >> > 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
> >> > 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
> >> > 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
> >> > 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
> >> > 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
> >> >
> >
> >
> >
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
2010-01-03 15:37 dz-tor
@ 2010-01-08 19:34 ` hermann pitton
0 siblings, 0 replies; 12+ messages in thread
From: hermann pitton @ 2010-01-08 19:34 UTC (permalink / raw)
To: dz-tor; +Cc: video4linux-list
Hi,
Am Sonntag, den 03.01.2010, 16:37 +0100 schrieb dz-tor:
> Hi,
>
> I want to ask whether you are working on this 'issue'. I'm interested in
> the subject, as I'm owner of this card and cannot get this stuff to work
> - I've picture, no sound. Earlier you have written, that you can provide
> patches for testing. If offer is still actual, I can test them.
> Currently I'm using kernel 2.6.31, but if it's a problem I can switch to
> 2.6.32.
>
> As I wrote earlier I have the same card - Winfast TV2100 with FM, tv
> norm used in my country is PAL (I'm from Poland).
>
> Regards,
> Darek
please have a look at the xtal/oscillator close to the saa713x chip.
It can have two different values. See README.saa7134 in Documentation.
I'll provide a patch with best guessing based on the regspy.exe results
then, assuming all is connected to LINE2 and routed through the external
mux chip as a start. If that fails, we try with LINE1 next.
Cheers,
Hermann
> >
> >> Hey guys,
> >>
> >> Let me start by thanking you both for all your help. Unfortunately,
> >> there isn't much I can do with the data you provided - it's way too
> >> technical for me. I'd be happy to do any tests and apply any patches,
> >> but I would need some instructions - but only if you have time; I
> >> really don't want to burden you with this.
> >>
> >> Thanks again,
> >>
> >> Pavle.
> >>
> >>
> >>
> >> ________________________________
> >> From: hermann pitton<hermann-pitton@arcor.de>
> >> To: Terry Wu<terrywu2009@gmail.com>
> >> Cc: pavle.predic@yahoo.co.uk; video4linux-list@redhat.com
> >> Sent: Sat, 28 November, 2009 4:09:28
> >> Subject: Re: Re: Leadtek Winfast TV2100
> >>
> >> Hi Terry Wu,
> >>
> >> Am Donnerstag, den 26.11.2009, 10:33 +0800 schrieb Terry Wu:
> >> > Hi,
> >> >
> >> > Here are the subsystem IDs for different TV2100 models:
> >> > Subsystem ID:0x6f30107d, TVF8533-BDF (PAL BG/DK)
> >> > Subsystem ID:0x6f32107d, TVF5533-MF (NTSC)
> >> > Subsystem ID:0x6f3a107d, TVF88T5-B/DFF (PAL BG/DK, FM)
> >> >
> >> > Terry
> >>
> >> better is to become active on it.
> >>
> >> we can most likely help about how to match such tuners fine,
> >> if any doubts left, but the best is to send just patches with having
> >> such hardware to test on.
> >>
> >> Compared to the early tda9887 stuff on LeadTek devices, LeadTek was
> >> pioneering and we have that in mind, it should be fairly easy for those.
> >>
> >> Let's know the other way round too, where you have still concerns doing
> >> so.
> >>
> >> Cheers,
> >> Hermann
> >>
> >> > 2009/11/23 hermann pitton<hermann-pitton@arcor.de>:
> >> > > Hi, thanks again!
> >> > >
> >> > > Am Montag, den 23.11.2009, 09:42 +0800 schrieb Terry Wu:
> >> > >> Hi,
> >> > >>
> >> > >> Please refer to the attached JPEG file for the GPIO
> >> settings of
> >> > >> TV2100 with FM (PCB:B).
> >> > >>
> >> > >> Let me know if you need the information of TV2100 without FM
> >> > >> (PCB:A, TVF8533-BDF).
> >> > >>
> >> > >> Terry Wu
> >> > >
> >> > > On a first look, if we start to count gpios from zero, we tell
> >> the same.
> >> > >
> >> > > The TVF8533_BDF I would have to look up. It is four to five
> >> years back.
> >> > >
> >> > > If it uses that minor number TI chip without radio support, we
> >> treat it
> >> > > as tuner=69 too currently.
> >> > >
> >> > > For all such older can tuners, widely different about the globe,
> >> counts,
> >> > > that we don't have any way to detect them. So first working,
> >> either NTSC
> >> > > or PAL, sits in the pool position and others have to think twice.
> >> > >
> >> > > OEMs do code tuners into eeprom content, some do not at all,
> >> such doing
> >> > > it are in competition and don't follow the rules of the main chip
> >> > > manufacturer, Philips/NXP in that case, and go their own ways.
> >> > >
> >> > > So tuner tables are unstable across manufacturers.
> >> > >
> >> > > We often can't help that much in such cases, but implementing
> >> their own
> >> > > tuner eeprom detection into the linux drivers is of course still
> >> > > welcome. Hauppauge does it very successfully since years.
> >> > >
> >> > > We can't do much about it, if OEMs don't follow Philips or whom
> >> ever on
> >> > > such.
> >> > >
> >> > > Thanks,
> >> > > Hermann
> >> > >
> >> > >
> >> > >>
> >> > >> 2009/11/23 Terry Wu<terrywu2009@gmail.com>:
> >> > >> > Hi,
> >> > >> >
> >> > >> > The TVF88T5-BDFF data sheet is attached.
> >> > >> >
> >> > >> > Terry Wu
> >> > >> >
> >> > >> > 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
> >> > >> > 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
> >> > >> > 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
> >> > >> > 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
> >> > >> > 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
> >> > >> > 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
> >> > >> > 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
> >> > >> > 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
> >> > >> > 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
> >> > >> > 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
> >> > >> > 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
> >> > >> > 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
> >> > >> > 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
> >> > >> > 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
> >> > >> > 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
> >> > >> > 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
> >> > >> >
> >> > >
> >> > >
> >> > >
> >>
> >>
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Re: Leadtek Winfast TV2100
@ 2010-01-03 15:37 dz-tor
2010-01-08 19:34 ` hermann pitton
0 siblings, 1 reply; 12+ messages in thread
From: dz-tor @ 2010-01-03 15:37 UTC (permalink / raw)
To: hermann-pitton, terrywu2009, pavle.predic; +Cc: video4linux-list
Hi,
I want to ask whether you are working on this 'issue'. I'm interested in
the subject, as I'm owner of this card and cannot get this stuff to work
- I've picture, no sound. Earlier you have written, that you can provide
patches for testing. If offer is still actual, I can test them.
Currently I'm using kernel 2.6.31, but if it's a problem I can switch to
2.6.32.
As I wrote earlier I have the same card - Winfast TV2100 with FM, tv
norm used in my country is PAL (I'm from Poland).
Regards,
Darek
>
>> Hey guys,
>>
>> Let me start by thanking you both for all your help. Unfortunately,
>> there isn't much I can do with the data you provided - it's way too
>> technical for me. I'd be happy to do any tests and apply any patches,
>> but I would need some instructions - but only if you have time; I
>> really don't want to burden you with this.
>>
>> Thanks again,
>>
>> Pavle.
>>
>>
>>
>> ________________________________
>> From: hermann pitton<hermann-pitton@arcor.de>
>> To: Terry Wu<terrywu2009@gmail.com>
>> Cc: pavle.predic@yahoo.co.uk; video4linux-list@redhat.com
>> Sent: Sat, 28 November, 2009 4:09:28
>> Subject: Re: Re: Leadtek Winfast TV2100
>>
>> Hi Terry Wu,
>>
>> Am Donnerstag, den 26.11.2009, 10:33 +0800 schrieb Terry Wu:
>> > Hi,
>> >
>> > Here are the subsystem IDs for different TV2100 models:
>> > Subsystem ID:0x6f30107d, TVF8533-BDF (PAL BG/DK)
>> > Subsystem ID:0x6f32107d, TVF5533-MF (NTSC)
>> > Subsystem ID:0x6f3a107d, TVF88T5-B/DFF (PAL BG/DK, FM)
>> >
>> > Terry
>>
>> better is to become active on it.
>>
>> we can most likely help about how to match such tuners fine,
>> if any doubts left, but the best is to send just patches with having
>> such hardware to test on.
>>
>> Compared to the early tda9887 stuff on LeadTek devices, LeadTek was
>> pioneering and we have that in mind, it should be fairly easy for those.
>>
>> Let's know the other way round too, where you have still concerns doing
>> so.
>>
>> Cheers,
>> Hermann
>>
>> > 2009/11/23 hermann pitton<hermann-pitton@arcor.de>:
>> > > Hi, thanks again!
>> > >
>> > > Am Montag, den 23.11.2009, 09:42 +0800 schrieb Terry Wu:
>> > >> Hi,
>> > >>
>> > >> Please refer to the attached JPEG file for the GPIO
>> settings of
>> > >> TV2100 with FM (PCB:B).
>> > >>
>> > >> Let me know if you need the information of TV2100 without FM
>> > >> (PCB:A, TVF8533-BDF).
>> > >>
>> > >> Terry Wu
>> > >
>> > > On a first look, if we start to count gpios from zero, we tell
>> the same.
>> > >
>> > > The TVF8533_BDF I would have to look up. It is four to five
>> years back.
>> > >
>> > > If it uses that minor number TI chip without radio support, we
>> treat it
>> > > as tuner=69 too currently.
>> > >
>> > > For all such older can tuners, widely different about the globe,
>> counts,
>> > > that we don't have any way to detect them. So first working,
>> either NTSC
>> > > or PAL, sits in the pool position and others have to think twice.
>> > >
>> > > OEMs do code tuners into eeprom content, some do not at all,
>> such doing
>> > > it are in competition and don't follow the rules of the main chip
>> > > manufacturer, Philips/NXP in that case, and go their own ways.
>> > >
>> > > So tuner tables are unstable across manufacturers.
>> > >
>> > > We often can't help that much in such cases, but implementing
>> their own
>> > > tuner eeprom detection into the linux drivers is of course still
>> > > welcome. Hauppauge does it very successfully since years.
>> > >
>> > > We can't do much about it, if OEMs don't follow Philips or whom
>> ever on
>> > > such.
>> > >
>> > > Thanks,
>> > > Hermann
>> > >
>> > >
>> > >>
>> > >> 2009/11/23 Terry Wu<terrywu2009@gmail.com>:
>> > >> > Hi,
>> > >> >
>> > >> > The TVF88T5-BDFF data sheet is attached.
>> > >> >
>> > >> > Terry Wu
>> > >> >
>> > >> > 11/17/2003 06:39 PM 72,010 TVF5531-MF.pdf
>> > >> > 03/12/2008 11:37 AM 555,285 TVF5533-MF-.pdf
>> > >> > 02/24/2004 02:19 PM 120,727 TVF5533-MF.pdf
>> > >> > 12/30/2003 06:59 PM 91,577 TVF5831-MFF.pdf
>> > >> > 09/26/2005 10:20 AM 156,853 TVF78P3-MFF.pdf
>> > >> > 11/17/2003 06:39 PM 67,947 TVF8531-BDF.pdf
>> > >> > 11/17/2003 06:39 PM 67,715 TVF8531-DIF.pdf
>> > >> > 03/12/2008 11:37 AM 509,340 TVF8533-BDF.pdf
>> > >> > 03/12/2008 11:37 AM 507,295 TVF8533-DIF.pdf
>> > >> > 12/30/2003 06:59 PM 87,921 TVF8831-BDFF.pdf
>> > >> > 12/30/2003 06:59 PM 87,624 TVF8831-DIFF.pdf
>> > >> > 09/26/2005 10:20 AM 176,525 TVF88P3-CFF.pdf
>> > >> > 03/24/2006 10:48 AM 460,941 TVF88T5-BDFF.pdf
>> > >> > 02/24/2004 02:19 PM 132,304 TVF9533-BDF.pdf
>> > >> > 02/24/2004 02:19 PM 120,940 TVF9533-DIF.pdf
>> > >> > 03/12/2008 11:37 AM 458,967 TVF99T5-BDFF.pdf
>> > >> >
>> > >
>> > >
>> > >
>>
>>
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2010-01-08 19:45 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-11-21 22:33 Aw: Re: Leadtek Winfast TV2100 hermann-pitton
2009-11-22 12:51 ` Terry Wu
2009-11-22 22:30 ` hermann pitton
2009-11-23 1:23 ` Terry Wu
2009-11-23 1:42 ` Terry Wu
2009-11-23 2:30 ` hermann pitton
2009-11-26 2:33 ` Terry Wu
2009-11-28 3:09 ` hermann pitton
2009-11-28 18:04 ` Pavle Predic
2009-11-23 1:47 ` hermann pitton
2010-01-03 15:37 dz-tor
2010-01-08 19:34 ` hermann pitton
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.