[4/5] dmaengine: sprd: Add Spreadtrum DMA configuration

[Baolin Wang <baolin.wang@linaro.org>]

On 12 April 2018 at 19:30, Baolin Wang <baolin.wang@linaro.org> wrote:
> Hi Vinod,
>
> On 12 April 2018 at 17:37, Vinod Koul <vinod.koul@intel.com> wrote:
>> On Wed, Apr 11, 2018 at 08:13:28PM +0800, Baolin Wang wrote:
>>> Hi Vinod,
>>>
>>> On 11 April 2018 at 17:36, Vinod Koul <vinod.koul@intel.com> wrote:
>>> > On Tue, Apr 10, 2018 at 03:46:06PM +0800, Baolin Wang wrote:
>>> >
>>> >> +/*
>>> >> + * struct sprd_dma_config - DMA configuration structure
>>> >> + * @config: dma slave channel config
>>> >> + * @fragment_len: specify one fragment transfer length
>>> >> + * @block_len: specify one block transfer length
>>> >> + * @transcation_len: specify one transcation transfer length
>>> >> + * @wrap_ptr: wrap pointer address, once the transfer address reaches the
>>> >> + * 'wrap_ptr', the next transfer address will jump to the 'wrap_to' address.
>>> >> + * @wrap_to: wrap jump to address
>>> >> + * @req_mode: specify the DMA request mode
>>> >> + * @int_mode: specify the DMA interrupt type
>>> >> + */
>>> >> +struct sprd_dma_config {
>>> >> +     struct dma_slave_config config;
>>> >> +     u32 fragment_len;
>>> >
>>> > why not use _maxburst?
>>>
>>> Yes, I can use maxburst.
>>>
>>> >
>>> >> +     u32 block_len;
>>> >> +     u32 transcation_len;
>>> >
>>> > what does block and transaction len refer to here
>>>
>>>  Our DMA has 3 transfer mode: transaction transfer, block transfer and
>>> fragment transfer. One transaction transfer can contain several blocks
>>> transfer, and each block can be set proper block step. One block can
>>> contain several fragments transfer with proper fragment step. It can
>>> generate interrupts when one transaction transfer or block transfer or
>>> fragment transfer is completed if user set the interrupt type. So here
>>> we should set the length for transaction transfer, block transfer and
>>> fragment transfer.
>>
>> what are the max size these types support?
>
> These types max size definition:
>
> #define SPRD_DMA_FRG_LEN_MASK GENMASK(16, 0)
>
> #define SPRD_DMA_BLK_LEN_MASK GENMASK(16, 0)
>
> #define SPRD_DMA_TRSC_LEN_MASK GENMASK(27, 0)
>
>>>
>>> >
>>> >> +     phys_addr_t wrap_ptr;
>>> >> +     phys_addr_t wrap_to;
>>> >
>>> > this sound sg_list to me, why are we not using that here
>>>
>>> It is similar to sg list, but it is not one software action, we have
>>> hardware registers to help to jump one specified address.
>>>
>>> >
>>> >> +     enum sprd_dma_req_mode req_mode;
>>> >
>>> > Looking at definition of request mode we have frag, block, transaction list
>>> > etc.. That should depend upon dma request. If you have been asked to
>>> > transfer a list, you shall configure list mode. if it is a single
>>> > transaction then it should be transaction mode!
>>>
>>> If I understand your points correctly, you mean we can specify the
>>> request mode when requesting one slave channel by
>>> 'dma_request_slave_channel()'. But we need change the request mode
>>> dynamically following different transfer task for this channel, so I
>>> am afraid we can not specify the request mode of this channel at
>>> requesting time.
>>
>> Nope a channel has nothing to do with request type. You request and grab a
>> channel. Then you prepare a descriptor for a dma transaction. Based on
>> transaction requested you should intelligently break it down and create a
>> descriptor which uses transaction/block/fragment so that DMA throughput is
>> efficient. If prepare has sg list then you should use link list mode.
>> Further if you support max length, say 16KB and request is for 20KB you may
>> break it down for link list with two segments.
>
> OK. So I can add one more cell to specify the request mode for this channel.
>
> dmas = <&apdma 11 SPRD_DMA_BLK_REQ>
>
>>
>> Each prep call has flags associated, that can help you configure interrupt
>> behaviour.

After more thinking, I think this will be not useful for users, since
users need configure one DMA channel through different 3 places,
specify the request mode in dts, specify the interrupt type through
prep call flags, and other configuration need to be configured through
'struct sprd_dma_config'. That is not one good design for users. What
do you think? Thanks.