DriverDev-Devel Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v2 0/2] Add initial support for slimport anx7625
@ 2019-10-11  2:20 ` Xin Ji
  2019-10-11  2:21   ` [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding Xin Ji
                     ` (3 more replies)
  0 siblings, 4 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-11  2:20 UTC (permalink / raw)
  To: devel, Laurent Pinchart, Andrzej Hajda
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

Hi all,

The following series add initial support for the Slimport ANX7625 transmitter, a
ultra-low power Full-HD 4K MIPI to DP transmitter designed for portable device.

This is the initial version, any mistakes, please let me know, I will fix it in
the next series.

Thanks,
Xin


Xin Ji (2):
  dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver

 .../bindings/display/bridge/anx7625.yaml           |   96 +
 drivers/gpu/drm/bridge/Makefile                    |    2 +-
 drivers/gpu/drm/bridge/analogix/Kconfig            |    6 +
 drivers/gpu/drm/bridge/analogix/Makefile           |    1 +
 drivers/gpu/drm/bridge/analogix/anx7625.c          | 2153 ++++++++++++++++++++
 drivers/gpu/drm/bridge/analogix/anx7625.h          |  406 ++++
 6 files changed, 2663 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h

-- 
2.7.4

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-11  2:20 ` [PATCH v2 0/2] Add initial support for slimport anx7625 Xin Ji
@ 2019-10-11  2:21   ` Xin Ji
  2019-10-11 11:21     ` Andrzej Hajda
  2019-10-11  2:23   ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Xin Ji
                     ` (2 subsequent siblings)
  3 siblings, 1 reply; 17+ messages in thread
From: Xin Ji @ 2019-10-11  2:21 UTC (permalink / raw)
  To: devel, Laurent Pinchart, Andrzej Hajda
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
for portable device. It converts MIPI to DisplayPort 1.3 4K.

You can add support to your board with binding.

Example:
	anx7625_bridge: encoder@58 {
		compatible = "analogix,anx7625";
		reg = <0x58>;
		status = "okay";
		panel-flags = <1>;
		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		  reg = <0>;
		  anx_1_in: endpoint {
		    remote-endpoint = <&mipi_dsi>;
		  };
		};

		port@3 {
		  reg = <3>;
		  anx_1_out: endpoint {
		    remote-endpoint = <&panel_in>;
		  };
		};
	};

Signed-off-by: Xin Ji <xji@analogixsemi.com>
---
 .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml

diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
new file mode 100644
index 0000000..fc84683
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 Analogix Semiconductor, Inc.
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
+
+maintainers:
+  - Xin Ji <xji@analogixsemi.com>
+
+description: |
+  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
+  designed for portable devices.
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    items:
+      - const: analogix,anx7625
+
+  reg:
+    maxItems: 1
+
+  panel-flags:
+    description: indicate the panel is internal or external
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  enable-gpios:
+    description: used for power on chip control, POWER_EN pin D2.
+    maxItems: 1
+
+  reset-gpios:
+    description: used for reset chip control, RESET_N pin B7.
+    maxItems: 1
+
+  port@0:
+    type: object
+    description:
+      A port node pointing to MIPI DSI host port node.
+
+  port@1:
+    type: object
+    description:
+      A port node pointing to MIPI DPI host port node.
+
+  port@2:
+    type: object
+    description:
+      A port node pointing to external connector port node.
+
+  port@3:
+    type: object
+    description:
+      A port node pointing to eDP port node.
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+  - compatible
+  - reg
+  - port@0
+  - port@3
+
+example:
+  - |
+    anx7625_bridge: encoder@58 {
+        compatible = "analogix,anx7625";
+        reg = <0x58>;
+        status = "okay";
+        panel-flags = <1>;
+        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
+        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        port@0 {
+          reg = <0>;
+          anx_1_in: endpoint {
+            remote-endpoint = <&mipi_dsi>;
+          };
+        };
+
+        port@3 {
+          reg = <3>;
+          anx_1_out: endpoint {
+            remote-endpoint = <&panel_in>;
+          };
+        };
+    };
-- 
2.7.4

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver
  2019-10-11  2:20 ` [PATCH v2 0/2] Add initial support for slimport anx7625 Xin Ji
  2019-10-11  2:21   ` [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding Xin Ji
@ 2019-10-11  2:23   ` Xin Ji
  2019-10-14  8:20     ` kbuild test robot
                       ` (2 more replies)
  2019-10-11  6:12   ` [PATCH v2 0/2] Add initial support for slimport anx7625 Andrzej Hajda
  2019-10-11 10:27   ` Dan Carpenter
  3 siblings, 3 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-11  2:23 UTC (permalink / raw)
  To: devel, Laurent Pinchart, Andrzej Hajda
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
for portable device. It converts MIPI DSI/DPI to DisplayPort 1.3 4K.

The ANX7625 can support both USB Type-C PD feature and MIPI DSI/DPI
to DP feature. This driver only enabled MIPI DSI/DPI to DP feature.

Signed-off-by: Xin Ji <xji@analogixsemi.com>
---
 drivers/gpu/drm/bridge/Makefile           |    2 +-
 drivers/gpu/drm/bridge/analogix/Kconfig   |    6 +
 drivers/gpu/drm/bridge/analogix/Makefile  |    1 +
 drivers/gpu/drm/bridge/analogix/anx7625.c | 2153 +++++++++++++++++++++++++++++
 drivers/gpu/drm/bridge/analogix/anx7625.h |  406 ++++++
 5 files changed, 2567 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h

diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 4934fcf..bcd388a 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -12,8 +12,8 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o
 obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
 obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
 obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
-obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
 obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
 obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
 obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
+obj-y += analogix/
 obj-y += synopsys/
diff --git a/drivers/gpu/drm/bridge/analogix/Kconfig b/drivers/gpu/drm/bridge/analogix/Kconfig
index e930ff9..b2f127e 100644
--- a/drivers/gpu/drm/bridge/analogix/Kconfig
+++ b/drivers/gpu/drm/bridge/analogix/Kconfig
@@ -2,3 +2,9 @@
 config DRM_ANALOGIX_DP
 	tristate
 	depends on DRM
+
+config ANALOGIX_ANX7625
+	tristate "Analogix MIPI to DP interface support"
+	help
+		ANX7625 is an ultra-low power 4K mobile HD transmitter designed
+		for portable devices. It converts MIPI/DPI to DisplayPort1.3 4K.
diff --git a/drivers/gpu/drm/bridge/analogix/Makefile b/drivers/gpu/drm/bridge/analogix/Makefile
index fdbf3fd..8a52867 100644
--- a/drivers/gpu/drm/bridge/analogix/Makefile
+++ b/drivers/gpu/drm/bridge/analogix/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_ANALOGIX_ANX7625) += anx7625.o
 analogix_dp-objs := analogix_dp_core.o analogix_dp_reg.o
 obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix_dp.o
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
new file mode 100644
index 0000000..96adf3b
--- /dev/null
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -0,0 +1,2153 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright(c) 2016, Analogix Semiconductor. All rights reserved.
+ *
+ */
+#include <linux/extcon.h>
+#include <linux/gcd.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/of_platform.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_dp_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+#include <video/display_timing.h>
+
+#include "anx7625.h"
+
+/*
+ * there is a sync issue while access I2C register between AP(CPU) and
+ * internal firmware(OCM), to avoid the race condition, AP should access
+ * the reserved slave address before slave address occurs changes.
+ */
+static int i2c_access_workaround(struct anx7625_data *ctx,
+				 struct i2c_client *client)
+{
+	u8 offset;
+	struct device *dev = &client->dev;
+	int ret;
+
+	if (client == ctx->last_client)
+		return 0;
+
+	ctx->last_client = client;
+
+	if (client == ctx->i2c.tcpc_client)
+		offset = RSVD_00_ADDR;
+	else if (client == ctx->i2c.tx_p0_client)
+		offset = RSVD_D1_ADDR;
+	else if (client == ctx->i2c.tx_p1_client)
+		offset = RSVD_60_ADDR;
+	else if (client == ctx->i2c.rx_p0_client)
+		offset = RSVD_39_ADDR;
+	else if (client == ctx->i2c.rx_p1_client)
+		offset = RSVD_7F_ADDR;
+	else
+		offset = RSVD_00_ADDR;
+
+	ret = i2c_smbus_write_byte_data(client, offset, 0x00);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev,
+			      "failed to access i2c id=%x\n:%x",
+			      client->addr, offset);
+
+	return ret;
+}
+
+static int anx7625_reg_read(struct anx7625_data *ctx,
+			    struct i2c_client *client, u8 reg_addr)
+{
+	int ret;
+	struct device *dev = &client->dev;
+
+	i2c_access_workaround(ctx, client);
+
+	ret = i2c_smbus_read_byte_data(client, reg_addr);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "read i2c failed id=%x:%x\n",
+			      client->addr, reg_addr);
+
+	return ret;
+}
+
+static int anx7625_reg_block_read(struct anx7625_data *ctx,
+				  struct i2c_client *client,
+				  u8 reg_addr, u8 len, u8 *buf)
+{
+	int ret;
+	struct device *dev = &client->dev;
+
+	i2c_access_workaround(ctx, client);
+
+	ret = i2c_smbus_read_i2c_block_data(client, reg_addr, len, buf);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "read i2c block failed id=%x:%x\n",
+			      client->addr, reg_addr);
+
+	return ret;
+}
+
+static int anx7625_reg_write(struct anx7625_data *ctx,
+			     struct i2c_client *client,
+			     u8 reg_addr, u8 reg_val)
+{
+	int ret;
+	struct device *dev = &client->dev;
+
+	i2c_access_workaround(ctx, client);
+
+	ret = i2c_smbus_write_byte_data(client, reg_addr, reg_val);
+
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "failed to write i2c id=%x\n:%x",
+			      client->addr, reg_addr);
+
+	return ret;
+}
+
+static int anx7625_write_or(struct anx7625_data *ctx,
+			    struct i2c_client *client,
+			    u8 offset, u8 mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client, offset, (val | (mask)));
+}
+
+static int anx7625_write_and(struct anx7625_data *ctx,
+			     struct i2c_client *client,
+			     u8 offset, u8 mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client, offset, (val & (mask)));
+}
+
+static int anx7625_write_and_or(struct anx7625_data *ctx,
+				struct i2c_client *client,
+				u8 offset, u8 and_mask, u8 or_mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client,
+				 offset, (val & and_mask) | (or_mask));
+}
+
+static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
+{
+	int i, ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CONTROL_REGISTER, 0x80);
+	for (i = 0; i < 13; i++)
+		ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+					 VIDEO_BIT_MATRIX_12 + i,
+					 0x18 + i);
+
+	return ret;
+}
+
+static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)
+{
+	return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS);
+}
+
+static int wait_aux_op_finish(struct anx7625_data *ctx)
+{
+	int val;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	ret = readx_poll_timeout(anx7625_read_ctrl_status_p0,
+				 ctx, val,
+				 (!(val & AP_AUX_CTRL_OP_EN) || (val < 0)),
+				 2000,
+				 2000 * 150);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "aux operation failed!\n");
+		return -EIO;
+	}
+
+	val = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+			       AP_AUX_CTRL_STATUS);
+	if (val < 0 || (val & 0x0F)) {
+		DRM_DEV_ERROR(dev, "aux status %02x\n", val);
+		val = -EIO;
+	}
+
+	return val;
+}
+
+static int write_dpcd_addr(struct anx7625_data *ctx,
+			   u8 addrh, u8 addrm, u8 addrl)
+{
+	int ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_ADDR_7_0, (u8)addrl);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_15_8, (u8)addrm);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_19_16, (u8)addrh);
+
+	return ret;
+}
+
+static int sp_tx_aux_dpcdread_bytes(struct anx7625_data *ctx,
+				    u8 addrh, u8 addrm,
+				    u8 addrl, u8 count,
+				    u8 *buf)
+{
+	u8 c;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	if (WARN_ON(count > MAX_DPCD_BUFFER_SIZE))
+		return -E2BIG;
+
+	/* command and length */
+	c = ((count - 1) << 4) | 0x09;
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, AP_AUX_COMMAND, c);
+	/* address */
+	ret |= write_dpcd_addr(ctx, addrh, addrm, addrl);
+	/* aux en */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS,
+				AP_AUX_CTRL_OP_EN);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "aux enable failed.\n");
+		return ret;
+	}
+
+	usleep_range(2000, 2100);
+
+	ret = wait_aux_op_finish(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "aux read failed\n");
+		return ret;
+	}
+
+	return anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+			AP_AUX_BUFF_START, count, buf);
+}
+
+static int anx7625_video_mute_control(struct anx7625_data *ctx,
+				      u8 status)
+{
+	int ret;
+
+	if (status) { /* mute on */
+		/* set mute flag */
+		ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				       AP_AV_STATUS, AP_MIPI_MUTE);
+		/* clear mipi RX en */
+		ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+					 AP_AV_STATUS, (u8)~AP_MIPI_RX_EN);
+	} else { /* mute off */
+		/* clear mute flag */
+		ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+					AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+		/* set MIPI RX EN */
+		ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+					AP_AV_STATUS, AP_MIPI_RX_EN);
+	}
+
+	return ret;
+}
+
+static int anx7625_config_audio_input(struct anx7625_data *ctx)
+{
+	int ret;
+
+	/* channel num */
+	ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5);
+	/* layout */
+	/* as I2S channel is 2, no need to set layout */
+
+	/* FS */
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_4,
+				    0xf0, AUDIO_FS_48K);
+	/* word length */
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_5,
+				    0xf0, AUDIO_W_LEN_24_24MAX);
+	/* I2S */
+	ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE);
+	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
+				 AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE);
+	/* audio change flag */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AV_STATUS, AP_AUDIO_CHG);
+
+	if (ret < 0)
+		DRM_ERROR("failed to config audio.\n");
+
+	return ret;
+}
+
+/* reduction of fraction a/b */
+static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b)
+{
+	unsigned long gcd_num;
+	unsigned long tmp_a, tmp_b;
+	u32 i = 1;
+
+	gcd_num = gcd(*a, *b);
+	*a /= gcd_num;
+	*b /= gcd_num;
+
+	tmp_a = *a;
+	tmp_b = *b;
+
+	while ((*a > MAX_UNSIGNED_24BIT) || (*b > MAX_UNSIGNED_24BIT)) {
+		i++;
+		*a = tmp_a / i;
+		*b = tmp_b / i;
+	}
+
+	/*
+	 * in the end, make a, b larger to have higher ODFC PLL
+	 * output frequency accuracy
+	 */
+	while ((*a < MAX_UNSIGNED_24BIT) && (*b < MAX_UNSIGNED_24BIT)) {
+		*a <<= 1;
+		*b <<= 1;
+	}
+
+	*a >>= 1;
+	*b >>= 1;
+}
+
+static int anx7625_calculate_m_n(u32 pixelclock,
+				 unsigned long *m,
+				 unsigned long *n,
+				 u8 *post_divider)
+{
+	if (pixelclock > PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN) {
+		/* pixel clock frequency is too high */
+		DRM_ERROR("pixelclock too high, act(%d), maximum(%lu)\n",
+			  pixelclock,
+			  PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN);
+		return -EINVAL;
+	}
+
+	if (pixelclock < PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX) {
+		/* pixel clock frequency is too low */
+		DRM_ERROR("pixelclock too low, act(%d), maximum(%lu)\n",
+			  pixelclock,
+			  PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX);
+		return -EINVAL;
+	}
+
+	for (*post_divider = 1;
+		pixelclock < (PLL_OUT_FREQ_MIN / (*post_divider));)
+		*post_divider += 1;
+
+	if (*post_divider > POST_DIVIDER_MAX) {
+		for (*post_divider = 1;
+			(pixelclock <
+			 (PLL_OUT_FREQ_ABS_MIN / (*post_divider)));)
+			*post_divider += 1;
+
+		if (*post_divider > POST_DIVIDER_MAX) {
+			DRM_ERROR("cannot find property post_divider(%d)\n",
+				  *post_divider);
+			return -EDOM;
+		}
+	}
+
+	/* patch to improve the accuracy */
+	if (*post_divider == 7) {
+		/* 27,000,000 is not divisible by 7 */
+		*post_divider = 8;
+	} else if (*post_divider == 11) {
+		/* 27,000,000 is not divisible by 11 */
+		*post_divider = 12;
+	} else if ((*post_divider == 13) || (*post_divider == 14)) {
+		/*27,000,000 is not divisible by 13 or 14*/
+		*post_divider = 15;
+	}
+
+	if (pixelclock * (*post_divider) > PLL_OUT_FREQ_ABS_MAX) {
+		DRM_ERROR("act clock(%u) large than maximum(%lu)\n",
+			  pixelclock * (*post_divider),
+			  PLL_OUT_FREQ_ABS_MAX);
+		return -EDOM;
+	}
+
+	*m = pixelclock;
+	*n = XTAL_FRQ / (*post_divider);
+
+	anx7625_reduction_of_a_fraction(m, n);
+
+	return 0;
+}
+
+static int anx7625_odfc_config(struct anx7625_data *ctx,
+			       u8 post_divider)
+{
+	int ret;
+
+	/* config input reference clock frequency 27MHz/19.2MHz */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16,
+				~(REF_CLK_27000KHZ << MIPI_FREF_D_IND));
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16,
+				(REF_CLK_27000KHZ << MIPI_FREF_D_IND));
+	/* post divider */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_8, 0x0f);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_8,
+				post_divider << 4);
+
+	/* add patch for MIS2-125 (5pcs ANX7625 fail ATE MBIST test) */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+				 ~MIPI_PLL_VCO_TUNE_REG_VAL);
+
+	/* reset ODFC PLL */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+				 ~MIPI_PLL_RESET_N);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+				MIPI_PLL_RESET_N);
+
+	if (ret < 0)
+		DRM_ERROR("IO error.\n");
+
+	return ret;
+}
+
+static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	unsigned long m, n;
+	u16 htotal;
+	int ret;
+	u8 post_divider = 0;
+
+	ret = anx7625_calculate_m_n(ctx->dt.pixelclock.min * 1000,
+				    &m, &n, &post_divider);
+
+	if (ret) {
+		DRM_ERROR("cannot get property m n value.\n");
+		return ret;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "compute M(%lu), N(%lu), divider(%d).\n",
+			     m, n, post_divider);
+
+	/* configure pixel clock */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_L,
+				(ctx->dt.pixelclock.min / 1000) & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_H,
+				 (ctx->dt.pixelclock.min / 1000) >> 8);
+	/* lane count */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+			MIPI_LANE_CTRL_0, 0xfc);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client,
+				MIPI_LANE_CTRL_0, 3);
+
+	/* Htotal */
+	htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min +
+		ctx->dt.hback_porch.min + ctx->dt.hsync_len.min;
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_TOTAL_PIXELS_L, htotal & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_TOTAL_PIXELS_H, htotal >> 8);
+	/* Hactive */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_ACTIVE_PIXELS_L, ctx->dt.hactive.min & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_ACTIVE_PIXELS_H, ctx->dt.hactive.min >> 8);
+	/* HFP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_FRONT_PORCH_L, ctx->dt.hfront_porch.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_FRONT_PORCH_H,
+			ctx->dt.hfront_porch.min >> 8);
+	/* HWS */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_SYNC_WIDTH_L, ctx->dt.hsync_len.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_SYNC_WIDTH_H, ctx->dt.hsync_len.min >> 8);
+	/* HBP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_BACK_PORCH_L, ctx->dt.hback_porch.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_BACK_PORCH_H, ctx->dt.hback_porch.min >> 8);
+	/* Vactive */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_L,
+			ctx->dt.vactive.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_H,
+			ctx->dt.vactive.min >> 8);
+	/* VFP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			VERTICAL_FRONT_PORCH, ctx->dt.vfront_porch.min);
+	/* VWS */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			VERTICAL_SYNC_WIDTH, ctx->dt.vsync_len.min);
+	/* VBP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			VERTICAL_BACK_PORCH, ctx->dt.vback_porch.min);
+	/* M value */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_M_NUM_23_16, (m >> 16) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_M_NUM_15_8, (m >> 8) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_M_NUM_7_0, (m & 0xff));
+	/* N value */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_N_NUM_23_16, (n >> 16) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_N_NUM_15_8, (n >> 8) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_PLL_N_NUM_7_0,
+			(n & 0xff));
+	/* diff */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_DIGITAL_ADJ_1, 0x37);
+
+	ret |= anx7625_odfc_config(ctx, post_divider - 1);
+
+	if (ret < 0)
+		DRM_ERROR("mipi dsi setup IO error.\n");
+
+	return ret;
+}
+
+static int anx7625_swap_dsi_lane3(struct anx7625_data *ctx)
+{
+	int val;
+
+	/* swap MIPI-DSI data lane 3 P and N */
+	val = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP);
+	if (val < 0) {
+		DRM_ERROR("IO error : access MIPI_SWAP.\n");
+		return -EIO;
+	}
+
+	val |= (1 << MIPI_SWAP_CH3);
+	return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP, val);
+}
+
+static int anx7625_api_dsi_config(struct anx7625_data *ctx)
+
+{
+	int val, ret;
+
+	/* swap MIPI-DSI data lane 3 P and N */
+	ret = anx7625_swap_dsi_lane3(ctx);
+	if (ret < 0) {
+		DRM_ERROR("IO error : swap dsi lane 3 failed.\n");
+		return ret;
+	}
+
+	/* DSI clock settings */
+	val = (0 << MIPI_HS_PWD_CLK)		|
+		(0 << MIPI_HS_RT_CLK)		|
+		(0 << MIPI_PD_CLK)		|
+		(1 << MIPI_CLK_RT_MANUAL_PD_EN)	|
+		(1 << MIPI_CLK_HS_MANUAL_PD_EN)	|
+		(0 << MIPI_CLK_DET_DET_BYPASS)	|
+		(0 << MIPI_CLK_MISS_CTRL)	|
+		(0 << MIPI_PD_LPTX_CH_MANUAL_PD_EN);
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				MIPI_PHY_CONTROL_3, val);
+
+	/*
+	 * Decreased HS prepare timing delay from 160ns to 80ns work with
+	 *     a) Dragon board 810 series (Qualcomm AP)
+	 *     b) Moving Pixel DSI source (PG3A pattern generator +
+	 *	P332 D-PHY Probe) default D-PHY timing
+	 *	5ns/step
+	 */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_TIME_HS_PRPR, 0x10);
+
+	/* enable DSI mode*/
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_18,
+				SELECT_DSI << MIPI_DPI_SELECT);
+
+	ret |= anx7625_dsi_video_timing_config(ctx);
+	if (ret < 0) {
+		DRM_ERROR("dsi video timing config failed\n");
+		return ret;
+	}
+
+	/* toggle m, n ready */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6,
+				~(MIPI_M_NUM_READY | MIPI_N_NUM_READY));
+	usleep_range(1000, 1100);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6,
+				MIPI_M_NUM_READY | MIPI_N_NUM_READY);
+
+	/* configure integer stable register */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_VIDEO_STABLE_CNT, 0x02);
+	/* power on MIPI RX */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x00);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x80);
+
+	if (ret < 0)
+		DRM_ERROR("IO error : mipi dsi enable init failed.\n");
+
+	return ret;
+}
+
+static int anx7625_dsi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "config dsi.\n");
+
+	/* DSC disable */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				R_DSC_CTRL_0, ~DSC_EN);
+
+	ret |= anx7625_api_dsi_config(ctx);
+
+	if (ret < 0) {
+		DRM_ERROR("IO error : api dsi config error.\n");
+		return ret;
+	}
+
+	/* set MIPI RX EN */
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+			       AP_AV_STATUS, AP_MIPI_RX_EN);
+	/* clear mute flag */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+	if (ret < 0)
+		DRM_ERROR("IO error : enable mipi rx failed.\n");
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "success to config DSI\n");
+
+	return ret;
+}
+
+static int anx7625_api_dpi_config(struct anx7625_data *ctx)
+{
+	u16 freq = ctx->dt.pixelclock.min / 1000;
+	int ret;
+
+	/* configure pixel clock */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				PIXEL_CLOCK_L, freq & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 PIXEL_CLOCK_H, (freq >> 8));
+
+	/* set DPI mode */
+	/* set to DPI PLL module sel */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_9, 0x20);
+	/* power down MIPI */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x08);
+	/* enable DPI mode */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_18, 0x1C);
+	/* set first edge */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				 VIDEO_CONTROL_0, 0x05);
+	if (ret < 0)
+		DRM_ERROR("IO error : dpi phy set failed.\n");
+
+	return ret;
+}
+
+static int anx7625_dpi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
+
+	/* DSC disable */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				R_DSC_CTRL_0, ~DSC_EN);
+	if (ret < 0) {
+		DRM_ERROR("IO error : disable dsc failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_config_bit_matrix(ctx);
+	if (ret < 0) {
+		DRM_ERROR("config bit matrix failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_api_dpi_config(ctx);
+	if (ret < 0) {
+		DRM_ERROR("mipi phy(dpi) setup failed.\n");
+		return ret;
+	}
+
+	/* set MIPI RX EN */
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+			       AP_AV_STATUS, AP_MIPI_RX_EN);
+	/* clear mute flag */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+	if (ret < 0)
+		DRM_ERROR("IO error : enable mipi rx failed.\n");
+
+	return ret;
+}
+
+const u8 ANX_OUI[3] = { 0x00, 0x22, 0xB9 };
+static int is_anx_dongle(struct anx7625_data *ctx)
+{
+	u8 buf[3];
+
+	/* 0x0500~0x0502: BRANCH_IEEE_OUI */
+	sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x05, 0x00, sizeof(buf), buf);
+	if (memcmp(buf, ANX_OUI, sizeof(buf)) == 0)
+		return 0;
+
+	return -ENXIO;
+}
+
+static void sp_tx_get_rx_bw(struct anx7625_data *ctx, u8 *bw)
+{
+	u8 data_buf[4];
+	/*
+	 * When ANX dongle connected, if CHIP_ID = 0x7750, bandwidth is 6.75G,
+	 * because ANX7750 DPCD 0x052x was not available.
+	 */
+	if (!is_anx_dongle(ctx)) {
+		sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x05, 0x03, 0x04, data_buf);
+		if (data_buf[0] == 0x37 && data_buf[1] == 0x37 &&
+		    data_buf[2] == 0x35 && data_buf[3] == 0x30) {
+			/* 0x19 : 6.75G */
+			*bw = 0x19;
+		} else {
+			sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x05, 0x21, 1, bw);
+			/*
+			 * some ANX dongle read out value 0,
+			 * retry standard register.
+			 */
+			if (((*bw) == 0) || ((*bw) == 0xff))
+				sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x00,
+							 DPCD_MAX_LINK_RATE,
+							 1, bw);
+		}
+	} else {
+		sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x00,
+					 DPCD_MAX_LINK_RATE, 1, bw);
+	}
+}
+
+static void anx7625_dp_start(struct anx7625_data *ctx)
+{
+	int ret;
+
+	if (!ctx->display_timing_valid) {
+		DRM_ERROR("mipi drm haven't set display timing yet.\n");
+		return;
+	}
+
+	anx7625_config_audio_input(ctx);
+
+	if (ctx->pdata.dsi_supported)
+		ret = anx7625_dsi_config(ctx);
+	else
+		ret = anx7625_dpi_config(ctx);
+
+	if (ret < 0)
+		DRM_ERROR("MIPI phy setup error.\n");
+}
+
+static void anx7625_dp_stop(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n");
+
+	/*
+	 * video disable: 0x72:08 bit 7 = 0;
+	 * audio disable: 0x70:87 bit 0 = 0;
+	 */
+	ret = anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 0x87, 0xfe);
+	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f);
+
+	ret |= anx7625_video_mute_control(ctx, 1);
+	if (ret < 0)
+		DRM_ERROR("IO error : mute video failed\n");
+}
+
+static int sp_tx_rst_aux(struct anx7625_data *ctx)
+{
+	int ret;
+
+	ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, RST_CTRL2,
+			       AUX_RST);
+	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, RST_CTRL2,
+				 ~AUX_RST);
+	return ret;
+}
+
+static int sp_tx_aux_wr(struct anx7625_data *ctx, u8 offset)
+{
+	int ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_BUFF_START, offset);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_COMMAND, 0x04);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+	return (ret | wait_aux_op_finish(ctx));
+}
+
+static int sp_tx_aux_rd(struct anx7625_data *ctx, u8 len_cmd)
+{
+	int ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_COMMAND, len_cmd);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+	return (ret | wait_aux_op_finish(ctx));
+}
+
+static int sp_tx_get_edid_block(struct anx7625_data *ctx)
+{
+	int c = 0;
+	struct device *dev = &ctx->client->dev;
+
+	sp_tx_aux_wr(ctx, 0x7e);
+	sp_tx_aux_rd(ctx, 0x01);
+	c = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_BUFF_START);
+	if (c < 0) {
+		DRM_ERROR("IO error : access AUX BUFF.\n");
+		return -EIO;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, " EDID Block = %d\n", c + 1);
+
+	if (c > MAX_EDID_BLOCK)
+		c = 1;
+
+	return c;
+}
+
+static int edid_read(struct anx7625_data *ctx,
+		     u8 offset, u8 *pblock_buf)
+{
+	int ret, cnt;
+	struct device *dev = &ctx->client->dev;
+
+	for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) {
+		sp_tx_aux_wr(ctx, offset);
+		/* set I2C read com 0x01 mot = 0 and read 16 bytes */
+		ret = sp_tx_aux_rd(ctx, 0xf1);
+
+		if (ret) {
+			sp_tx_rst_aux(ctx);
+			DRM_DEV_DEBUG_DRIVER(dev, "edid read failed, reset!\n");
+		} else {
+			ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+						     AP_AUX_BUFF_START,
+						     MAX_DPCD_BUFFER_SIZE,
+						     pblock_buf);
+			if (!ret)
+				break;
+		}
+	}
+
+	if (cnt > EDID_TRY_CNT)
+		return -EIO;
+
+	return 0;
+}
+
+static int segments_edid_read(struct anx7625_data *ctx,
+			      u8 segment, u8 *buf, u8 offset)
+{
+	u8 cnt;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	/* write address only */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_ADDR_7_0, 0x30);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_COMMAND, 0x04);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_CTRL_STATUS,
+				 AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN);
+
+	ret |= wait_aux_op_finish(ctx);
+	/* write segment address */
+	ret |= sp_tx_aux_wr(ctx, segment);
+	/* data read */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_7_0, 0x50);
+	if (ret) {
+		DRM_ERROR("IO error : aux initial failed.\n");
+		return ret;
+	}
+
+	for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) {
+		sp_tx_aux_wr(ctx, offset);
+		/* set I2C read com 0x01 mot = 0 and read 16 bytes */
+		ret = sp_tx_aux_rd(ctx, 0xf1);
+
+		if (ret) {
+			ret = sp_tx_rst_aux(ctx);
+			DRM_DEV_ERROR(dev, "segment read failed, reset!\n");
+		} else {
+			ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+						     AP_AUX_BUFF_START,
+						     MAX_DPCD_BUFFER_SIZE, buf);
+			if (!ret)
+				break;
+		}
+	}
+
+	if (cnt > EDID_TRY_CNT)
+		return -EIO;
+
+	return 0;
+}
+
+static int sp_tx_edid_read(struct anx7625_data *ctx,
+			   u8 *pedid_blocks_buf)
+{
+	u8 offset, edid_pos;
+	int count, blocks_num;
+	u8 pblock_buf[MAX_DPCD_BUFFER_SIZE];
+	u8 i, j;
+	u8 g_edid_break = 0;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	/* address initial */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_ADDR_7_0, 0x50);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_15_8, 0);
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_19_16, 0xf0);
+	if (ret < 0) {
+		DRM_ERROR("access aux channel IO error.\n");
+		return -EIO;
+	}
+
+	blocks_num = sp_tx_get_edid_block(ctx);
+	if (blocks_num < 0)
+		return blocks_num;
+
+	count = 0;
+
+	do {
+		switch (count) {
+		case 0:
+		case 1:
+			for (i = 0; i < 8; i++) {
+				offset = (i + count * 8) * MAX_DPCD_BUFFER_SIZE;
+				g_edid_break = edid_read(ctx, offset,
+							 pblock_buf);
+
+				if (g_edid_break)
+					break;
+
+				memcpy(&pedid_blocks_buf[offset],
+				       pblock_buf,
+				       MAX_DPCD_BUFFER_SIZE);
+			}
+
+			break;
+		case 2:
+			offset = 0x00;
+
+			for (j = 0; j < 8; j++) {
+				edid_pos = (j + count * 8) *
+					MAX_DPCD_BUFFER_SIZE;
+
+				if (g_edid_break == 1)
+					break;
+
+				segments_edid_read(ctx, count / 2,
+						   pblock_buf, offset);
+				memcpy(&pedid_blocks_buf[edid_pos],
+				       pblock_buf,
+				       MAX_DPCD_BUFFER_SIZE);
+				offset = offset + 0x10;
+			}
+
+			break;
+		case 3:
+			offset = 0x80;
+
+			for (j = 0; j < 8; j++) {
+				edid_pos = (j + count * 8) *
+					MAX_DPCD_BUFFER_SIZE;
+				if (g_edid_break == 1)
+					break;
+
+				segments_edid_read(ctx, count / 2,
+						   pblock_buf, offset);
+				memcpy(&pedid_blocks_buf[edid_pos],
+				       pblock_buf,
+				       MAX_DPCD_BUFFER_SIZE);
+				offset = offset + 0x10;
+			}
+
+			break;
+		default:
+			break;
+		}
+
+		count++;
+
+	} while (blocks_num >= count);
+
+	/* check edid data */
+	if (!drm_edid_is_valid((struct edid *)pedid_blocks_buf)) {
+		DRM_DEV_ERROR(dev, "WARNING! edid check failed!\n");
+		return -EINVAL;
+	}
+
+	/* reset aux channel */
+	sp_tx_rst_aux(ctx);
+
+	return (blocks_num + 1);
+}
+
+static void anx7625_power_on(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+
+	if (!ctx->pdata.low_power_mode) {
+		DRM_DEV_DEBUG_DRIVER(dev, "Anx7625 not low power mode!\n");
+		return;
+	}
+
+	/* power on pin enable */
+	gpiod_set_value(ctx->pdata.gpio_p_on, 1);
+	usleep_range(10000, 11000);
+	/* power reset pin enable */
+	gpiod_set_value(ctx->pdata.gpio_reset, 1);
+	usleep_range(10000, 11000);
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Anx7625 power on !\n");
+}
+
+static void anx7625_power_standby(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+
+	if (!ctx->pdata.low_power_mode) {
+		DRM_DEV_DEBUG_DRIVER(dev, "anx7625 not low power mode!\n");
+		return;
+	}
+
+	gpiod_set_value(ctx->pdata.gpio_reset, 0);
+	usleep_range(1000, 1100);
+	gpiod_set_value(ctx->pdata.gpio_p_on, 0);
+	usleep_range(1000, 1100);
+	DRM_DEV_DEBUG_DRIVER(dev, "anx7625 power down\n");
+}
+
+/* basic configurations of ANX7625 */
+static void anx7625_config(struct anx7625_data *ctx)
+{
+	anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+			  XTAL_FRQ_SEL, XTAL_FRQ_27M);
+}
+
+static void anx7625_disable_pd_protocol(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	/* reset main ocm */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40);
+	/* Disable PD */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, AP_DISABLE_PD);
+	/* release main ocm */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x00);
+
+	if (ret < 0)
+		DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature failed.\n");
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n");
+}
+
+static void anx7625_power_on_init(struct anx7625_data *ctx)
+{
+	int retry_count, i;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	for (retry_count = 0; retry_count < 3; retry_count++) {
+		anx7625_power_on(ctx);
+		anx7625_config(ctx);
+
+		for (i = 0; i < OCM_LOADING_TIME; i++) {
+			/* check interface workable */
+			ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+					       FLASH_LOAD_STA);
+			if (ret < 0) {
+				DRM_ERROR("IO error : access flash load.\n");
+				return;
+			}
+			if ((ret & FLASH_LOAD_STA_CHK) == FLASH_LOAD_STA_CHK) {
+				anx7625_disable_pd_protocol(ctx);
+				DRM_DEV_DEBUG_DRIVER(dev,
+						     "Firmware ver %02x%02x,",
+					anx7625_reg_read(ctx,
+							 ctx->i2c.rx_p0_client,
+							 OCM_FW_VERSION),
+					anx7625_reg_read(ctx,
+							 ctx->i2c.rx_p0_client,
+							 OCM_FW_REVERSION));
+				DRM_DEV_DEBUG_DRIVER(dev, "Driver version %s\n",
+						     ANX7625_DRV_VERSION);
+
+				return;
+			}
+			usleep_range(1000, 1100);
+		}
+		anx7625_power_standby(ctx);
+	}
+}
+
+static int anx7625_extcon_notifier(struct notifier_block *nb,
+				   unsigned long event, void *ptr)
+{
+	struct anx7625_data *ctx =
+		container_of(nb, struct anx7625_data, event_nb);
+
+	schedule_work(&ctx->extcon_wq);
+	return NOTIFY_DONE;
+}
+
+static void anx7625_chip_control(struct anx7625_data *ctx, int state)
+{
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "before set, power_state(%d).\n",
+			     atomic_read(&ctx->power_status));
+
+	if (!ctx->pdata.low_power_mode)
+		return;
+
+	if (state) {
+		atomic_inc(&ctx->power_status);
+		if (atomic_read(&ctx->power_status) == 1)
+			anx7625_power_on_init(ctx);
+	} else {
+		if (atomic_read(&ctx->power_status)) {
+			atomic_dec(&ctx->power_status);
+
+			if (atomic_read(&ctx->power_status) == 0)
+				anx7625_power_standby(ctx);
+		}
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "after set, power_state(%d).\n",
+			     atomic_read(&ctx->power_status));
+}
+
+static void anx7625_extcon_work(struct work_struct *work)
+{
+	struct anx7625_data *ctx =
+		container_of(work, struct anx7625_data, extcon_wq);
+	int state = extcon_get_state(ctx->extcon, EXTCON_DISP_DP);
+
+	mutex_lock(&ctx->lock);
+	anx7625_chip_control(ctx, state);
+	mutex_unlock(&ctx->lock);
+}
+
+static int anx7625_extcon_notifier_init(struct anx7625_data *ctx)
+{
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	ctx->event_nb.notifier_call = anx7625_extcon_notifier;
+	INIT_WORK(&ctx->extcon_wq, anx7625_extcon_work);
+	ret = devm_extcon_register_notifier(&ctx->client->dev, ctx->extcon,
+					    EXTCON_DISP_DP, &ctx->event_nb);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to register notifier for DP");
+		return ret;
+	}
+	return 0;
+}
+
+static void anx7625_init_gpio(struct anx7625_data *platform)
+{
+	struct device *dev = &platform->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "anx7625 init gpio\n");
+
+	/* gpio for chip power enable */
+	platform->pdata.gpio_p_on =
+		devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW);
+	/* gpio for chip reset */
+	platform->pdata.gpio_reset =
+		devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+
+	if (platform->pdata.gpio_p_on && platform->pdata.gpio_reset) {
+		platform->pdata.low_power_mode = 1;
+		DRM_DEV_DEBUG_DRIVER(dev, "low power mode, pon %d, reset %d.\n",
+				     desc_to_gpio(platform->pdata.gpio_p_on),
+				     desc_to_gpio(platform->pdata.gpio_reset));
+	} else {
+		platform->pdata.low_power_mode = 0;
+		DRM_DEV_DEBUG_DRIVER(dev, "not low power mode.\n");
+	}
+}
+
+static void anx7625_stop_dp_work(struct anx7625_data *ctx)
+{
+	ctx->hpd_status = 0;
+	ctx->hpd_high_cnt = 0;
+	ctx->display_timing_valid = 0;
+
+	ctx->slimport_edid_p.edid_block_num = -1;
+
+	if (ctx->pdata.low_power_mode == 0)
+		anx7625_disable_pd_protocol(ctx);
+}
+
+static void anx7625_start_dp_work(struct anx7625_data *ctx)
+{
+	int ret;
+	u8 buf[MAX_DPCD_BUFFER_SIZE];
+	u8 hdcp_cap;
+	struct device *dev = &ctx->client->dev;
+	u8 sp_tx_bw; /* linktraining banwidth */
+	u8 sp_tx_lane_count; /* link training lane count */
+
+	if (ctx->hpd_high_cnt >= 2) {
+		DRM_DEV_DEBUG_DRIVER(dev, "anx7625 filter useless HPD\n");
+		return;
+	}
+
+	ctx->hpd_high_cnt++;
+
+	sp_tx_get_rx_bw(ctx, &sp_tx_bw);
+
+	sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x00, DPCD_MAX_LANE_COUNT,
+				 1, &sp_tx_lane_count);
+
+	sp_tx_lane_count = sp_tx_lane_count & 0x1f;
+	sp_tx_aux_dpcdread_bytes(ctx, 0x06, 0x80, 0x28, 1, buf);/* read Bcap */
+
+	hdcp_cap = buf[0] & 0x01;
+
+	/* not support HDCP */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f);
+
+	if (hdcp_cap == 0x01)
+		DRM_DEV_DEBUG_DRIVER(dev, "HDCP1.4\n");
+
+	/* try auth flag */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
+	/* interrupt for DRM */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
+	if (ret < 0)
+		return;
+	DRM_DEV_DEBUG_DRIVER(dev, "MAX BW=%02x, MAX Lane cnt=%02x, HDCP=%02x\n",
+			     (u32)sp_tx_bw,
+			     (u32)sp_tx_lane_count,
+			     (u32)hdcp_cap);
+
+	ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
+	if (ret < 0)
+		return;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Secure OCM version=%02x\n", ret);
+}
+
+static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
+{
+	return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
+}
+
+static void anx7625_hpd_polling(struct anx7625_data *ctx)
+{
+	int ret, val;
+	struct device *dev = &ctx->client->dev;
+
+	if (atomic_read(&ctx->power_status) != 1) {
+		DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
+		return;
+	}
+
+	ret = readx_poll_timeout(anx7625_read_hpd_status_p0,
+				 ctx, val,
+				 ((val & HPD_STATUS) || (val < 0)),
+				 5000,
+				 5000 * 100);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "HPD polling timeout!\n");
+	} else {
+		DRM_DEV_DEBUG_DRIVER(dev, "HPD raise up.\n");
+		anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+				  INTR_ALERT_1, 0xFF);
+		anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				  INTERFACE_CHANGE_INT, 0);
+	}
+
+	anx7625_start_dp_work(ctx);
+}
+
+static void anx7625_disconnect_check(struct anx7625_data *ctx)
+{
+	if (atomic_read(&ctx->power_status) == 0)
+		anx7625_stop_dp_work(ctx);
+}
+
+static void anx7625_low_power_mode_check(struct anx7625_data *ctx,
+					 int state)
+{
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "low power mode check, state(%d).\n", state);
+
+	if (ctx->pdata.low_power_mode) {
+		anx7625_chip_control(ctx, state);
+		if (state)
+			anx7625_hpd_polling(ctx);
+		else
+			anx7625_disconnect_check(ctx);
+	}
+}
+
+static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
+{
+	struct device *dev = &ctx->client->dev;
+
+	/* hpd changed */
+	DRM_DEV_DEBUG_DRIVER(dev, "dp_hpd_change_default_func: %d\n",
+			     (u32)on);
+
+	if (on == 0) {
+		DRM_DEV_DEBUG_DRIVER(dev, " HPD low\n");
+		anx7625_stop_dp_work(ctx);
+	} else {
+		DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
+		anx7625_start_dp_work(ctx);
+	}
+
+	ctx->hpd_status = 1;
+}
+
+static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
+{
+	int intr_vector, status;
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "power_status=%d\n",
+			     (u32)atomic_read(&ctx->power_status));
+
+	status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+				   INTR_ALERT_1, 0xFF);
+	if (status < 0) {
+		DRM_ERROR("IO error : clear alert register.\n");
+		return status;
+	}
+
+	intr_vector = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+				       INTERFACE_CHANGE_INT);
+	if (intr_vector < 0) {
+		DRM_ERROR("IO error : access interrupt change register.\n");
+		return intr_vector;
+	}
+	DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x44=%x\n", intr_vector);
+	status = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				   INTERFACE_CHANGE_INT,
+				   intr_vector & (~intr_vector));
+	if (status < 0) {
+		DRM_ERROR("IO error : clear interrupt change register.\n");
+		return status;
+	}
+
+	if (!(intr_vector & HPD_STATUS_CHANGE))
+		return -ENOENT;
+
+	status = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+				  SYSTEM_STSTUS);
+	if (status < 0) {
+		DRM_ERROR("IO error : clear interrupt status.\n");
+		return status;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x45=%x\n", status);
+	dp_hpd_change_handler(ctx, status & HPD_STATUS);
+
+	return 0;
+}
+
+static void anx7625_work_func(struct work_struct *work)
+{
+	int event;
+	struct anx7625_data *ctx = container_of(work,
+						struct anx7625_data, work);
+
+	mutex_lock(&ctx->lock);
+	event = anx7625_hpd_change_detect(ctx);
+	mutex_unlock(&ctx->lock);
+
+	if (event < 0)
+		return;
+
+	if (ctx->bridge_attached)
+		drm_helper_hpd_irq_event(ctx->connector.dev);
+}
+
+static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
+{
+	struct anx7625_data *ctx = (struct anx7625_data *)data;
+
+	if (atomic_read(&ctx->power_status) != 1)
+		return IRQ_NONE;
+
+	queue_work(ctx->workqueue, &ctx->work);
+
+	return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_OF
+static int anx7625_parse_dt(struct device *dev,
+			    struct anx7625_platform_data *pdata)
+{
+	struct device_node *np = dev->of_node;
+	struct device_node *panel_node, *out_ep;
+
+	of_property_read_u32(dev->of_node, "panel_flags",
+			     &pdata->internal_panel);
+
+	pdata->node.mipi_dsi_host_node = of_graph_get_remote_node(np, 0, 0);
+	if (pdata->node.mipi_dsi_host_node) {
+		of_node_put(pdata->node.mipi_dsi_host_node);
+		pdata->dsi_supported = 1;
+		DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
+	} else {
+		pdata->node.mipi_dpi_host_node =
+			of_graph_get_remote_node(np, 1, 0);
+
+		if (pdata->node.mipi_dpi_host_node) {
+			of_node_put(pdata->node.mipi_dpi_host_node);
+			DRM_DEV_DEBUG_DRIVER(dev, "found dpi host node.\n");
+		}
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "dsi_supported : %d\n", pdata->dsi_supported);
+
+	pdata->node.extcon_node = of_graph_get_port_by_id(np, 2);
+	pdata->node.panel_node = of_graph_get_port_by_id(np, 3);
+	if (pdata->node.extcon_node)
+		pdata->extcon_supported = 1;
+
+	if (pdata->node.panel_node) {
+		of_node_put(pdata->node.panel_node);
+		out_ep = of_get_child_by_name(pdata->node.panel_node,
+					      "endpoint");
+		if (!out_ep) {
+			DRM_DEV_DEBUG_DRIVER(dev, "cannot get endpoint.\n");
+			return -EPROBE_DEFER;
+		}
+
+		panel_node = of_graph_get_remote_port_parent(out_ep);
+		of_node_put(out_ep);
+
+		pdata->panel = of_drm_find_panel(panel_node);
+		DRM_DEV_DEBUG_DRIVER(dev, "get panel node.\n");
+		of_node_put(panel_node);
+		if (IS_ERR_OR_NULL(pdata->panel))
+			return -EPROBE_DEFER;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "%s support extcon, %s internal panel\n",
+			     pdata->extcon_supported ? "" : "not",
+			     pdata->internal_panel ? "has" : "no");
+
+	return 0;
+}
+#else
+static int anx7625_parse_dt(struct device *dev,
+			    struct anx7625_platform_data *pdata)
+{
+	return -ENODEV;
+}
+#endif
+
+static inline struct anx7625_data *connector_to_anx7625(struct drm_connector *c)
+{
+	return container_of(c, struct anx7625_data, connector);
+}
+
+static inline struct anx7625_data *bridge_to_anx7625(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct anx7625_data, bridge);
+}
+
+static void anx7625_post_disable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "post disable\n");
+
+	if (!ctx->pdata.panel)
+		return;
+
+	ret = drm_panel_unprepare(ctx->pdata.panel);
+	if (ret)
+		DRM_ERROR("failed to unprepare panel: %d\n", ret);
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "backlight unprepared.\n");
+
+	atomic_set(&ctx->panel_power, 0);
+}
+
+static void anx7625_pre_enable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "pre enable\n");
+
+	if (!ctx->pdata.panel)
+		return;
+
+	ret = drm_panel_prepare(ctx->pdata.panel);
+	if (ret < 0)
+		DRM_ERROR("failed to prepare panel: %d\n", ret);
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "backlight prepared.\n");
+	atomic_set(&ctx->panel_power, 1);
+}
+
+static int anx7625_get_modes(struct drm_connector *connector)
+{
+	struct anx7625_data *ctx = connector_to_anx7625(connector);
+	int err, num_modes = 0;
+	int turn_off_flag = 0;
+	struct s_edid_data *p_edid = &ctx->slimport_edid_p;
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm get modes\n");
+
+	if (ctx->slimport_edid_p.edid_block_num > 0)
+		goto out;
+
+	mutex_lock(&ctx->lock);
+
+	if (ctx->pdata.panel && atomic_read(&ctx->panel_power) == 0) {
+		turn_off_flag = 1;
+		anx7625_pre_enable(&ctx->bridge);
+	}
+
+	anx7625_low_power_mode_check(ctx, 1);
+
+	p_edid->edid_block_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data);
+
+	err = -EIO;
+	if (p_edid->edid_block_num < 0) {
+		DRM_ERROR("Failed to read EDID.\n");
+		goto fail;
+	}
+
+	err = drm_connector_update_edid_property(connector,
+						 (struct edid *)
+						 &p_edid->edid_raw_data);
+
+	if (err)
+		DRM_ERROR("Failed to update EDID property: %d\n", err);
+
+fail:
+	mutex_unlock(&ctx->lock);
+	anx7625_low_power_mode_check(ctx, 0);
+	if (ctx->pdata.panel && turn_off_flag == 1)
+		anx7625_post_disable(&ctx->bridge);
+
+	if (err)
+		return err;
+
+out:
+	num_modes = drm_add_edid_modes(connector,
+				       (struct edid *)&p_edid->edid_raw_data);
+	DRM_DEV_DEBUG_DRIVER(dev, "num_modes(%d)\n", num_modes);
+
+	return num_modes;
+}
+
+static enum drm_mode_status
+anx7625_connector_mode_valid(struct drm_connector *connector,
+			     struct drm_display_mode *mode)
+{
+	struct anx7625_data *ctx = connector_to_anx7625(connector);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm modes valid verify\n");
+
+	if (mode->clock > SUPPORT_PIXEL_CLOCK)
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
+}
+
+static struct drm_connector_helper_funcs anx7625_connector_helper_funcs = {
+	.get_modes = anx7625_get_modes,
+	.mode_valid = anx7625_connector_mode_valid,
+};
+
+static enum drm_connector_status anx7625_detect(struct drm_connector *connector,
+						bool force)
+{
+	struct anx7625_data *ctx = connector_to_anx7625(connector);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm detect\n");
+
+	if (ctx->pdata.internal_panel)
+		return connector_status_connected;
+
+	if (!ctx->hpd_status)
+		return connector_status_disconnected;
+
+	return connector_status_connected;
+}
+
+static const struct drm_connector_funcs anx7625_connector_funcs = {
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.detect = anx7625_detect,
+	.destroy = drm_connector_cleanup,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static int anx7625_attach_dsi(struct anx7625_data *ctx)
+{
+	struct mipi_dsi_host *host;
+	struct mipi_dsi_device *dsi;
+	struct device_node *mipi_host_node;
+	struct device *dev = &ctx->client->dev;
+	const struct mipi_dsi_device_info info = {
+		.type = "anx7625",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	DRM_DEV_DEBUG_DRIVER(dev, "attach dsi\n");
+
+	if (ctx->pdata.dsi_supported)
+		mipi_host_node = ctx->pdata.node.mipi_dsi_host_node;
+	else
+		mipi_host_node = ctx->pdata.node.mipi_dpi_host_node;
+
+	if (!mipi_host_node) {
+		DRM_ERROR("dsi host is not configured.\n");
+		return -EINVAL;
+	}
+
+	host = of_find_mipi_dsi_host_by_node(mipi_host_node);
+	if (!host) {
+		DRM_ERROR("failed to find dsi host.\n");
+		return -EINVAL;
+	}
+
+	dsi = mipi_dsi_device_register_full(host, &info);
+	if (IS_ERR(dsi)) {
+		DRM_ERROR("failed to create dsi device.\n");
+		return -EINVAL;
+	}
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO	|
+		MIPI_DSI_MODE_VIDEO_SYNC_PULSE	|
+		MIPI_DSI_MODE_EOT_PACKET	|
+		MIPI_DSI_MODE_VIDEO_HSE;
+
+	if (mipi_dsi_attach(dsi) < 0) {
+		DRM_ERROR("failed to attach dsi to host.\n");
+		mipi_dsi_device_unregister(dsi);
+		return -EINVAL;
+	}
+
+	ctx->dsi = dsi;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "attach dsi succeeded.\n");
+
+	return 0;
+}
+
+static void anx7625_bridge_detach(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+
+	if (ctx->dsi) {
+		mipi_dsi_detach(ctx->dsi);
+		mipi_dsi_device_unregister(ctx->dsi);
+	}
+
+	if (ctx->bridge_attached)
+		drm_connector_unregister(&ctx->connector);
+}
+
+static int anx7625_bridge_attach(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	int err;
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm attach\n");
+	if (!bridge->encoder) {
+		DRM_ERROR("Parent encoder object not found");
+		return -ENODEV;
+	}
+
+	err = drm_connector_init(bridge->dev, &ctx->connector,
+				 &anx7625_connector_funcs,
+				 DRM_MODE_CONNECTOR_DisplayPort);
+	if (err) {
+		DRM_ERROR("Failed to initialize connector: %d\n", err);
+		return err;
+	}
+
+	drm_connector_helper_add(&ctx->connector,
+				 &anx7625_connector_helper_funcs);
+
+	err = drm_connector_register(&ctx->connector);
+	if (err) {
+		DRM_ERROR("Failed to register connector: %d\n", err);
+		return err;
+	}
+
+	ctx->connector.polled = DRM_CONNECTOR_POLL_HPD;
+
+	err = drm_connector_attach_encoder(&ctx->connector, bridge->encoder);
+	if (err) {
+		DRM_ERROR("Failed to link up connector to encoder: %d\n", err);
+		drm_connector_unregister(&ctx->connector);
+		return err;
+	}
+
+	err = anx7625_attach_dsi(ctx);
+	if (err) {
+		DRM_ERROR("Failed to attach to dsi : %d\n", err);
+		drm_connector_unregister(&ctx->connector);
+		return err;
+	}
+
+	ctx->bridge_attached = 1;
+
+	return 0;
+}
+
+static enum drm_mode_status
+anx7625_bridge_mode_valid(struct drm_bridge *bridge,
+			  const struct drm_display_mode *mode)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm mode checking\n");
+
+	/* Max 1200p at 5.4 Ghz, one lane, pixel clock 300M */
+	if (mode->clock > SUPPORT_PIXEL_CLOCK) {
+		DRM_DEV_DEBUG_DRIVER(dev,
+				     "drm mode invalid, pixelclock too high.\n");
+		return MODE_CLOCK_HIGH;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm mode valid.\n");
+
+	return MODE_OK;
+}
+
+static void anx7625_bridge_mode_set(struct drm_bridge *bridge,
+				    const struct drm_display_mode *old_mode,
+				    const struct drm_display_mode *mode)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm mode set\n");
+
+	mutex_lock(&ctx->lock);
+
+	ctx->dt.pixelclock.min = mode->clock;
+	ctx->dt.hactive.min = mode->hdisplay;
+	ctx->dt.hsync_len.min = mode->hsync_end - mode->hsync_start;
+	ctx->dt.hfront_porch.min = mode->hsync_start - mode->hdisplay;
+	ctx->dt.hback_porch.min = mode->htotal - mode->hsync_end;
+	ctx->dt.vactive.min = mode->vdisplay;
+	ctx->dt.vsync_len.min = mode->vsync_end - mode->vsync_start;
+	ctx->dt.vfront_porch.min = mode->vsync_start - mode->vdisplay;
+	ctx->dt.vback_porch.min = mode->vtotal - mode->vsync_end;
+
+	ctx->display_timing_valid = 1;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "pixelclock(%d).\n", ctx->dt.pixelclock.min);
+	DRM_DEV_DEBUG_DRIVER(dev, "hactive(%d), hsync(%d), hfp(%d), hbp(%d)\n",
+			     ctx->dt.hactive.min,
+			     ctx->dt.hsync_len.min,
+			     ctx->dt.hfront_porch.min,
+			     ctx->dt.hback_porch.min);
+	DRM_DEV_DEBUG_DRIVER(dev, "vactive(%d), vsync(%d), vfp(%d), vbp(%d)\n",
+			     ctx->dt.vactive.min,
+			     ctx->dt.vsync_len.min,
+			     ctx->dt.vfront_porch.min,
+			     ctx->dt.vback_porch.min);
+	DRM_DEV_DEBUG_DRIVER(dev, "hdisplay(%d),hsync_start(%d).\n",
+			     mode->hdisplay,
+			     mode->hsync_start);
+	DRM_DEV_DEBUG_DRIVER(dev, "hsync_end(%d),htotal(%d).\n",
+			     mode->hsync_end,
+			     mode->htotal);
+	DRM_DEV_DEBUG_DRIVER(dev, "vdisplay(%d),vsync_start(%d).\n",
+			     mode->vdisplay,
+			     mode->vsync_start);
+	DRM_DEV_DEBUG_DRIVER(dev, "vsync_end(%d),vtotal(%d).\n",
+			     mode->vsync_end,
+			     mode->vtotal);
+
+	mutex_unlock(&ctx->lock);
+}
+
+static void anx7625_bridge_enable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm enable\n");
+
+	anx7625_low_power_mode_check(ctx, 1);
+
+	if (WARN_ON(!atomic_read(&ctx->power_status)))
+		return;
+
+	if (ctx->pdata.panel) {
+		ret = drm_panel_enable(ctx->pdata.panel);
+		if (ret < 0) {
+			DRM_ERROR("failed to enable panel: %d.\n", ret);
+			return;
+		}
+	}
+
+	mutex_lock(&ctx->lock);
+	anx7625_dp_start(ctx);
+	mutex_unlock(&ctx->lock);
+}
+
+static void anx7625_bridge_disable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	if (WARN_ON(!atomic_read(&ctx->power_status)))
+		return;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
+
+	if (ctx->pdata.panel) {
+		ret = drm_panel_disable(ctx->pdata.panel);
+		if (ret < 0)
+			DRM_ERROR("failed to disable panel: %d.\n", ret);
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
+	mutex_lock(&ctx->lock);
+
+	anx7625_dp_stop(ctx);
+
+	anx7625_low_power_mode_check(ctx, 0);
+
+	mutex_unlock(&ctx->lock);
+}
+
+static const struct drm_bridge_funcs anx7625_bridge_funcs = {
+	.attach = anx7625_bridge_attach,
+	.detach = anx7625_bridge_detach,
+	.disable = anx7625_bridge_disable,
+	.post_disable = anx7625_post_disable,
+	.pre_enable = anx7625_pre_enable,
+	.mode_valid = anx7625_bridge_mode_valid,
+	.mode_set = anx7625_bridge_mode_set,
+	.enable = anx7625_bridge_enable,
+};
+
+static int anx7625_register_i2c_dummy_clients(struct anx7625_data *ctx,
+					      struct i2c_client *client)
+{
+	ctx->i2c.tx_p0_client = i2c_new_dummy(client->adapter,
+					      TX_P0_ADDR >> 1);
+	if (!ctx->i2c.tx_p0_client)
+		return -ENOMEM;
+
+	ctx->i2c.tx_p1_client = i2c_new_dummy(client->adapter,
+					      TX_P1_ADDR >> 1);
+	if (!ctx->i2c.tx_p1_client)
+		goto free_tx_p0;
+
+	ctx->i2c.tx_p2_client = i2c_new_dummy(client->adapter,
+					      TX_P2_ADDR >> 1);
+	if (!ctx->i2c.tx_p2_client)
+		goto free_tx_p1;
+
+	ctx->i2c.rx_p0_client = i2c_new_dummy(client->adapter,
+					      RX_P0_ADDR >> 1);
+	if (!ctx->i2c.rx_p0_client)
+		goto free_tx_p2;
+
+	ctx->i2c.rx_p1_client = i2c_new_dummy(client->adapter,
+					      RX_P1_ADDR >> 1);
+	if (!ctx->i2c.rx_p1_client)
+		goto free_rx_p0;
+
+	ctx->i2c.rx_p2_client = i2c_new_dummy(client->adapter,
+					      RX_P2_ADDR >> 1);
+	if (!ctx->i2c.rx_p2_client)
+		goto free_rx_p1;
+
+	ctx->i2c.tcpc_client = i2c_new_dummy(client->adapter,
+					     TCPC_INTERFACE_ADDR >> 1);
+	if (!ctx->i2c.tcpc_client)
+		goto free_rx_p2;
+
+	return 0;
+
+free_rx_p2:
+	i2c_unregister_device(ctx->i2c.rx_p2_client);
+free_rx_p1:
+	i2c_unregister_device(ctx->i2c.rx_p1_client);
+free_rx_p0:
+	i2c_unregister_device(ctx->i2c.rx_p0_client);
+free_tx_p2:
+	i2c_unregister_device(ctx->i2c.tx_p2_client);
+free_tx_p1:
+	i2c_unregister_device(ctx->i2c.tx_p1_client);
+free_tx_p0:
+	i2c_unregister_device(ctx->i2c.tx_p0_client);
+
+	return -ENOMEM;
+}
+
+static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx)
+{
+	i2c_unregister_device(ctx->i2c.tx_p0_client);
+	i2c_unregister_device(ctx->i2c.tx_p1_client);
+	i2c_unregister_device(ctx->i2c.tx_p2_client);
+	i2c_unregister_device(ctx->i2c.rx_p0_client);
+	i2c_unregister_device(ctx->i2c.rx_p1_client);
+	i2c_unregister_device(ctx->i2c.rx_p2_client);
+	i2c_unregister_device(ctx->i2c.tcpc_client);
+}
+
+static int anx7625_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	struct anx7625_data *platform;
+	struct anx7625_platform_data *pdata;
+	int ret = 0;
+	struct device *dev = &client->dev;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_I2C_BLOCK)) {
+		DRM_DEV_ERROR(dev, "anx7625's i2c bus doesn't support\n");
+		return -ENODEV;
+	}
+
+	platform = kzalloc(sizeof(*platform), GFP_KERNEL);
+	if (!platform) {
+		DRM_DEV_ERROR(dev, "failed to allocate driver data\n");
+		return -ENOMEM;
+	}
+
+	pdata = &platform->pdata;
+
+	ret = anx7625_parse_dt(dev, pdata);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to parse devicetree.\n");
+		goto free_platform;
+	}
+
+	anx7625_init_gpio(platform);
+
+	/* to access global platform data */
+	platform->client = client;
+	i2c_set_clientdata(client, platform);
+
+	if (platform->pdata.extcon_supported) {
+		/* get extcon device from DTS */
+		ret = -EINVAL;
+		platform->extcon = extcon_get_edev_by_phandle(dev, 0);
+		if (PTR_ERR(platform->extcon) == -EPROBE_DEFER)
+			goto free_platform;
+
+		if (IS_ERR(platform->extcon)) {
+			DRM_DEV_ERROR(dev,
+				      "can not get extcon device!");
+			goto free_platform;
+		}
+
+		ret = anx7625_extcon_notifier_init(platform);
+		if (ret)
+			goto free_platform;
+	}
+
+	atomic_set(&platform->power_status, 0);
+
+	mutex_init(&platform->lock);
+
+	platform->pdata.intp_irq = client->irq;
+	if (platform->pdata.intp_irq) {
+		INIT_WORK(&platform->work, anx7625_work_func);
+		platform->workqueue = create_workqueue("anx7625_work");
+		if (!platform->workqueue) {
+			DRM_DEV_ERROR(dev, "failed to create work queue\n");
+			ret = -ENOMEM;
+			goto free_platform;
+		}
+
+		ret = devm_request_threaded_irq(dev, platform->pdata.intp_irq,
+						NULL, anx7625_intr_hpd_isr,
+						IRQF_TRIGGER_FALLING |
+						IRQF_ONESHOT,
+						"anx7625-intp", platform);
+		if (ret) {
+			DRM_DEV_ERROR(dev, "failed to request irq\n");
+			goto free_wq;
+		}
+	}
+
+	if (anx7625_register_i2c_dummy_clients(platform, client) != 0) {
+		ret = -ENOMEM;
+		DRM_ERROR("Failed to reserve I2C bus.\n");
+		goto free_wq;
+	}
+
+	if (platform->pdata.low_power_mode == 0) {
+		anx7625_disable_pd_protocol(platform);
+		atomic_set(&platform->power_status, 1);
+	}
+
+	/* add work function */
+	if (platform->pdata.intp_irq)
+		queue_work(platform->workqueue, &platform->work);
+
+	platform->bridge.funcs = &anx7625_bridge_funcs;
+	if (IS_ENABLED(CONFIG_OF))
+		platform->bridge.of_node = client->dev.of_node;
+	drm_bridge_add(&platform->bridge);
+
+	DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
+
+	return 0;
+
+free_wq:
+	if (platform->workqueue)
+		destroy_workqueue(platform->workqueue);
+
+free_platform:
+	kfree(platform);
+
+	return ret;
+}
+
+static int anx7625_i2c_remove(struct i2c_client *client)
+{
+	struct anx7625_data *platform = i2c_get_clientdata(client);
+
+	drm_bridge_remove(&platform->bridge);
+
+	if (platform->pdata.intp_irq)
+		destroy_workqueue(platform->workqueue);
+
+	if (platform->pdata.extcon_supported) {
+		devm_extcon_unregister_notifier(&platform->client->dev,
+						platform->extcon,
+						EXTCON_DISP_DP,
+						&platform->event_nb);
+		flush_work(&platform->extcon_wq);
+	}
+
+	anx7625_unregister_i2c_dummy_clients(platform);
+
+	kfree(platform);
+	return 0;
+}
+
+static const struct i2c_device_id anx7625_id[] = {
+	{"anx7625", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, anx7625_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id anx_match_table[] = {
+	{.compatible = "analogix,anx7625",},
+	{},
+};
+#endif
+
+static struct i2c_driver anx7625_driver = {
+	.driver = {
+		.name = "anx7625",
+#ifdef CONFIG_OF
+		.of_match_table = anx_match_table,
+#endif
+	},
+	.probe = anx7625_i2c_probe,
+	.remove = anx7625_i2c_remove,
+
+	.id_table = anx7625_id,
+};
+
+module_i2c_driver(anx7625_driver);
+
+MODULE_DESCRIPTION("MIPI2DP anx7625 driver");
+MODULE_AUTHOR("Xin Ji <xji@analogixsemi.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION(ANX7625_DRV_VERSION);
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
new file mode 100644
index 0000000..0ffa8d0
--- /dev/null
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -0,0 +1,406 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright(c) 2016, Analogix Semiconductor. All rights reserved.
+ *
+ */
+
+#ifndef __ANX7625_H__
+#define __ANX7625_H__
+
+#ifndef LOG_TAG
+#define LOG_TAG "anx7625dp"
+#endif
+
+#define ANX7625_DRV_VERSION "0.1.04"
+
+/* Loading OCM re-trying times */
+#define OCM_LOADING_TIME 10
+
+/*********  ANX7625 Register  **********/
+#define TX_P0_ADDR				0x70
+#define TX_P1_ADDR				0x7A
+#define TX_P2_ADDR				0x72
+
+#define RX_P0_ADDR				0x7e
+#define RX_P1_ADDR				0x84
+#define RX_P2_ADDR				0x54
+
+#define RSVD_00_ADDR				0x00
+#define RSVD_D1_ADDR				0xD1
+#define RSVD_60_ADDR				0x60
+#define RSVD_39_ADDR				0x39
+#define RSVD_7F_ADDR				0x7F
+
+#define TCPC_INTERFACE_ADDR			0x58
+
+/* anx7625 clock frequency in Hz */
+#define XTAL_FRQ        (27 * 1000000)
+
+#define  POST_DIVIDER_MIN	1
+#define  POST_DIVIDER_MAX	16
+#define  PLL_OUT_FREQ_MIN	520000000UL
+#define  PLL_OUT_FREQ_MAX	730000000UL
+#define  PLL_OUT_FREQ_ABS_MIN	300000000UL
+#define  PLL_OUT_FREQ_ABS_MAX	800000000UL
+#define  MAX_UNSIGNED_24BIT	16777215UL
+
+/***************************************************************/
+/* Register definition of device address 0x58 */
+
+#define PRODUCT_ID_L 0x02
+#define PRODUCT_ID_H 0x03
+
+#define INTR_ALERT_1  0xCC
+#define INTR_SOFTWARE_INT BIT(3)
+#define INTR_RECEIVED_MSG BIT(5)
+
+#define SYSTEM_STSTUS 0x45
+#define INTERFACE_CHANGE_INT 0x44
+#define HPD_STATUS_CHANGE 0x80
+#define HPD_STATUS 0x80
+
+/******** END of I2C Address 0x58 ********/
+
+/***************************************************************/
+/* Register definition of device address 0x70 */
+#define  I2C_ADDR_70_DPTX              0x70
+
+#define SP_TX_LINK_BW_SET_REG 0xA0
+#define SP_TX_LANE_COUNT_SET_REG 0xA1
+
+#define M_VID_0 0xC0
+#define M_VID_1 0xC1
+#define M_VID_2 0xC2
+#define N_VID_0 0xC3
+#define N_VID_1 0xC4
+#define N_VID_2 0xC5
+
+/***************************************************************/
+/* Register definition of device address 0x72 */
+#define AUX_RST	0x04
+#define RST_CTRL2 0x07
+
+#define SP_TX_TOTAL_LINE_STA_L 0x24
+#define SP_TX_TOTAL_LINE_STA_H 0x25
+#define SP_TX_ACT_LINE_STA_L 0x26
+#define SP_TX_ACT_LINE_STA_H 0x27
+#define SP_TX_V_F_PORCH_STA 0x28
+#define SP_TX_V_SYNC_STA 0x29
+#define SP_TX_V_B_PORCH_STA 0x2A
+#define SP_TX_TOTAL_PIXEL_STA_L 0x2B
+#define SP_TX_TOTAL_PIXEL_STA_H 0x2C
+#define SP_TX_ACT_PIXEL_STA_L 0x2D
+#define SP_TX_ACT_PIXEL_STA_H 0x2E
+#define SP_TX_H_F_PORCH_STA_L 0x2F
+#define SP_TX_H_F_PORCH_STA_H 0x30
+#define SP_TX_H_SYNC_STA_L 0x31
+#define SP_TX_H_SYNC_STA_H 0x32
+#define SP_TX_H_B_PORCH_STA_L 0x33
+#define SP_TX_H_B_PORCH_STA_H 0x34
+
+#define SP_TX_VID_CTRL 0x84
+#define SP_TX_BPC_MASK 0xE0
+#define SP_TX_BPC_6    0x00
+#define SP_TX_BPC_8    0x20
+#define SP_TX_BPC_10   0x40
+#define SP_TX_BPC_12   0x60
+
+#define VIDEO_BIT_MATRIX_12 0x4c
+
+#define AUDIO_CHANNEL_STATUS_1 0xd0
+#define AUDIO_CHANNEL_STATUS_2 0xd1
+#define AUDIO_CHANNEL_STATUS_3 0xd2
+#define AUDIO_CHANNEL_STATUS_4 0xd3
+#define AUDIO_CHANNEL_STATUS_5 0xd4
+#define AUDIO_CHANNEL_STATUS_6 0xd5
+#define TDM_SLAVE_MODE 0x10
+#define I2S_SLAVE_MODE 0x08
+
+#define AUDIO_CONTROL_REGISTER 0xe6
+#define TDM_TIMING_MODE 0x08
+
+#define  I2C_ADDR_72_DPTX              0x72
+
+#define  VIDEO_CONTROL_0  0x08
+
+#define  ACTIVE_LINES_L         0x14
+#define  ACTIVE_LINES_H         0x15  /* note: bit[7:6] are reserved */
+#define  VERTICAL_FRONT_PORCH   0x16
+#define  VERTICAL_SYNC_WIDTH    0x17
+#define  VERTICAL_BACK_PORCH    0x18
+
+#define  HORIZONTAL_TOTAL_PIXELS_L    0x19
+#define  HORIZONTAL_TOTAL_PIXELS_H    0x1A  /* note: bit[7:6] are reserved */
+#define  HORIZONTAL_ACTIVE_PIXELS_L   0x1B
+#define  HORIZONTAL_ACTIVE_PIXELS_H   0x1C  /* note: bit[7:6] are reserved */
+#define  HORIZONTAL_FRONT_PORCH_L     0x1D
+#define  HORIZONTAL_FRONT_PORCH_H     0x1E  /* note: bit[7:4] are reserved */
+#define  HORIZONTAL_SYNC_WIDTH_L      0x1F
+#define  HORIZONTAL_SYNC_WIDTH_H      0x20  /* note: bit[7:4] are reserved */
+#define  HORIZONTAL_BACK_PORCH_L      0x21
+#define  HORIZONTAL_BACK_PORCH_H      0x22  /* note: bit[7:4] are reserved */
+
+/******** END of I2C Address 0x72 *********/
+/***************************************************************/
+/* Register definition of device address 0x7e */
+
+#define  I2C_ADDR_7E_FLASH_CONTROLLER  0x7E
+
+#define FLASH_LOAD_STA 0x05
+#define FLASH_LOAD_STA_CHK	BIT(7)
+
+#define  XTAL_FRQ_SEL    0x3F
+/* bit field positions */
+#define  XTAL_FRQ_SEL_POS    5
+/* bit field values */
+#define  XTAL_FRQ_19M2   (0 << XTAL_FRQ_SEL_POS)
+#define  XTAL_FRQ_27M    (4 << XTAL_FRQ_SEL_POS)
+
+#define  R_DSC_CTRL_0    0x40
+#define  READ_STATUS_EN  7
+#define  CLK_1MEG_RB     6  /* 1MHz clock reset; 0=reset, 0=reset release */
+#define  DSC_BIST_DONE   1  /* bit[5:1]: 1=DSC MBIST pass */
+#define  DSC_EN          0x01  /* 1=DSC enabled, 0=DSC disabled */
+
+#define OCM_FW_VERSION   0x31
+#define OCM_FW_REVERSION 0x32
+
+#define AP_AUX_ADDR_7_0   0x11
+#define AP_AUX_ADDR_15_8  0x12
+#define AP_AUX_ADDR_19_16 0x13
+
+/* note: bit[0:3] AUX status, bit 4 op_en, bit 5 address only */
+#define AP_AUX_CTRL_STATUS 0x14
+#define AP_AUX_CTRL_OP_EN 0x10
+#define AP_AUX_CTRL_ADDRONLY 0x20
+
+#define AP_AUX_BUFF_START 0x15
+#define PIXEL_CLOCK_L 0x25
+#define PIXEL_CLOCK_H 0x26
+
+#define AP_AUX_COMMAND 0x27  /* com+len */
+/* bit 0&1: 3D video structure */
+/* 0x01: frame packing,  0x02:Line alternative, 0x03:Side-by-side(full) */
+#define AP_AV_STATUS 0x28
+#define AP_VIDEO_CHG  BIT(2)
+#define AP_AUDIO_CHG  BIT(3)
+#define AP_MIPI_MUTE  BIT(4) /* 1:MIPI input mute, 0: ummute */
+#define AP_MIPI_RX_EN BIT(5) /* 1: MIPI RX input in  0: no RX in */
+#define AP_DISABLE_PD BIT(6)
+#define AP_DISABLE_DISPLAY BIT(7)
+/***************************************************************/
+/* Register definition of device address 0x84 */
+#define  MIPI_PHY_CONTROL_3            0x03
+#define  MIPI_HS_PWD_CLK               7
+#define  MIPI_HS_RT_CLK                6
+#define  MIPI_PD_CLK                   5
+#define  MIPI_CLK_RT_MANUAL_PD_EN      4
+#define  MIPI_CLK_HS_MANUAL_PD_EN      3
+#define  MIPI_CLK_DET_DET_BYPASS       2
+#define  MIPI_CLK_MISS_CTRL            1
+#define  MIPI_PD_LPTX_CH_MANUAL_PD_EN  0
+
+#define  MIPI_LANE_CTRL_0		0x05
+#define  MIPI_TIME_HS_PRPR		0x08
+
+/* After MIPI RX protocol layer received this many video frames, */
+/* protocol layer starts to reconstruct video stream from PHY */
+#define  MIPI_VIDEO_STABLE_CNT           0x0A
+
+#define  MIPI_LANE_CTRL_10               0x0F
+#define  MIPI_DIGITAL_ADJ_1   0x1B
+
+#define  MIPI_PLL_M_NUM_23_16   0x1E
+#define  MIPI_PLL_M_NUM_15_8    0x1F
+#define  MIPI_PLL_M_NUM_7_0     0x20
+#define  MIPI_PLL_N_NUM_23_16   0x21
+#define  MIPI_PLL_N_NUM_15_8    0x22
+#define  MIPI_PLL_N_NUM_7_0     0x23
+
+#define  MIPI_DIGITAL_PLL_6     0x2A
+/* bit[7:6]: VCO band control, only effective */
+/* when MIPI_PLL_FORCE_BAND_EN (0x84:0x2B[6]) is 1 */
+#define  MIPI_M_NUM_READY        0x10
+#define  MIPI_N_NUM_READY        0x08
+#define  STABLE_INTEGER_CNT_EN   0x04
+#define  MIPI_PLL_TEST_BIT       0
+/* bit[1:0]: test point output select - */
+/* 00: VCO power, 01: dvdd_pdt, 10: dvdd, 11: vcox */
+
+#define  MIPI_DIGITAL_PLL_7      0x2B
+#define  MIPI_PLL_FORCE_N_EN     7
+#define  MIPI_PLL_FORCE_BAND_EN  6
+
+#define  MIPI_PLL_VCO_TUNE_REG   4
+/* bit[5:4]: VCO metal capacitance - */
+/* 00: +20% fast, 01: +10% fast (default), 10: typical, 11: -10% slow */
+#define  MIPI_PLL_VCO_TUNE_REG_VAL   0x30
+
+#define  MIPI_PLL_PLL_LDO_BIT    2
+/* bit[3:2]: vco_v2i power - */
+/* 00: 1.40V, 01: 1.45V (default), 10: 1.50V, 11: 1.55V */
+#define  MIPI_PLL_RESET_N        0x02
+#define  MIPI_FRQ_FORCE_NDET     0
+
+#define  MIPI_ALERT_CLR_0        0x2D
+#define  HS_link_error_clear     7
+/* This bit itself is S/C, and it clears 0x84:0x31[7] */
+
+#define  MIPI_ALERT_OUT_0        0x31
+#define  check_sum_err_hs_sync   7
+/* This bit is cleared by 0x84:0x2D[7] */
+
+#define  MIPI_DIGITAL_PLL_8    0x33
+#define  MIPI_POST_DIV_VAL     4
+/* n means divided by (n+1), n = 0~15 */
+#define  MIPI_EN_LOCK_FRZ      3
+#define  MIPI_FRQ_COUNTER_RST  2
+#define  MIPI_FRQ_SET_REG_8    1
+/* bit 0 is reserved */
+
+#define  MIPI_DIGITAL_PLL_9    0x34
+
+#define  MIPI_DIGITAL_PLL_16   0x3B
+#define  MIPI_FRQ_FREEZE_NDET          7
+#define  MIPI_FRQ_REG_SET_ENABLE       6
+#define  MIPI_REG_FORCE_SEL_EN         5
+#define  MIPI_REG_SEL_DIV_REG          4
+#define  MIPI_REG_FORCE_PRE_DIV_EN     3
+/* bit 2 is reserved */
+#define  MIPI_FREF_D_IND               1
+#define  REF_CLK_27000KHZ    1
+#define  REF_CLK_19200KHZ    0
+#define  MIPI_REG_PLL_PLL_TEST_ENABLE  0
+
+#define  MIPI_DIGITAL_PLL_18  0x3D
+#define  FRQ_COUNT_RB_SEL       7
+#define  REG_FORCE_POST_DIV_EN  6
+#define  MIPI_DPI_SELECT        5
+#define  SELECT_DSI  1
+#define  SELECT_DPI  0
+#define  REG_BAUD_DIV_RATIO     0
+
+#define  H_BLANK_L            0x3E
+/* for DSC only */
+#define  H_BLANK_H            0x3F
+/* for DSC only; note: bit[7:6] are reserved */
+#define  MIPI_SWAP  0x4A
+#define  MIPI_SWAP_CH0    7
+#define  MIPI_SWAP_CH1    6
+#define  MIPI_SWAP_CH2    5
+#define  MIPI_SWAP_CH3    4
+#define  MIPI_SWAP_CLK    3
+/* bit[2:0] are reserved */
+
+/******** END of I2C Address 0x84 *********/
+
+/* DPCD regs */
+#define DPCD_DPCD_REV                  0x00
+#define DPCD_MAX_LINK_RATE             0x01
+#define DPCD_MAX_LANE_COUNT            0x02
+
+/*********  ANX7625 Register End  **********/
+
+/*****************  Display *****************/
+enum audio_fs {
+	AUDIO_FS_441K  = 0x00,
+	AUDIO_FS_48K   = 0x02,
+	AUDIO_FS_32K   = 0x03,
+	AUDIO_FS_882K  = 0x08,
+	AUDIO_FS_96K   = 0x0a,
+	AUDIO_FS_1764K = 0x0c,
+	AUDIO_FS_192K  = 0x0e
+};
+
+enum audio_wd_len {
+	AUDIO_W_LEN_16_20MAX = 0x02,
+	AUDIO_W_LEN_18_20MAX = 0x04,
+	AUDIO_W_LEN_17_20MAX = 0x0c,
+	AUDIO_W_LEN_19_20MAX = 0x08,
+	AUDIO_W_LEN_20_20MAX = 0x0a,
+	AUDIO_W_LEN_20_24MAX = 0x03,
+	AUDIO_W_LEN_22_24MAX = 0x05,
+	AUDIO_W_LEN_21_24MAX = 0x0d,
+	AUDIO_W_LEN_23_24MAX = 0x09,
+	AUDIO_W_LEN_24_24MAX = 0x0b
+};
+
+#define I2S_CH_2	0x01
+#define TDM_CH_4	0x03
+#define TDM_CH_6	0x05
+#define TDM_CH_8	0x07
+
+#define MAX_DPCD_BUFFER_SIZE	16
+
+#define ONE_BLOCK_SIZE      128
+#define FOUR_BLOCK_SIZE     (128 * 4)
+
+#define MAX_EDID_BLOCK	3
+#define EDID_TRY_CNT	3
+#define SUPPORT_PIXEL_CLOCK	300000
+
+struct s_edid_data {
+	int edid_block_num;
+	u8 edid_raw_data[FOUR_BLOCK_SIZE];
+};
+
+/*****************  Display End *****************/
+
+struct anx7625_device_node {
+	struct device_node *mipi_dsi_host_node;
+	struct device_node *mipi_dpi_host_node;
+	struct device_node *extcon_node;
+	struct device_node *panel_node;
+};
+
+struct anx7625_platform_data {
+	struct gpio_desc *gpio_p_on;
+	struct gpio_desc *gpio_reset;
+	struct drm_panel *panel;
+	int intp_irq;
+	u32 low_power_mode;
+	u32 dsi_supported;
+	u32 internal_panel;
+	u32 extcon_supported;
+	struct anx7625_device_node node;
+};
+
+struct anx7625_i2c_client {
+	struct i2c_client *tx_p0_client;
+	struct i2c_client *tx_p1_client;
+	struct i2c_client *tx_p2_client;
+	struct i2c_client *rx_p0_client;
+	struct i2c_client *rx_p1_client;
+	struct i2c_client *rx_p2_client;
+	struct i2c_client *tcpc_client;
+};
+
+struct anx7625_data {
+	struct anx7625_platform_data pdata;
+	atomic_t power_status;
+	atomic_t panel_power;
+	int hpd_status;
+	int hpd_high_cnt;
+	struct i2c_client *client;
+	struct anx7625_i2c_client i2c;
+	struct i2c_client *last_client;
+	struct s_edid_data slimport_edid_p;
+	struct work_struct work;
+	struct workqueue_struct *workqueue;
+	/* drm bridge mutex lock */
+	struct mutex lock;
+	char edid_block;
+	struct display_timing dt;
+	u8 display_timing_valid;
+	struct drm_bridge bridge;
+	u8 bridge_attached;
+	struct drm_connector connector;
+	struct mipi_dsi_device *dsi;
+	struct drm_dp_link link;
+	struct drm_display_mode vid_info;
+	struct notifier_block event_nb;
+	struct extcon_dev *extcon;
+	struct work_struct extcon_wq;
+};
+
+#endif  /* __ANX7625_H__ */
-- 
2.7.4

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 0/2] Add initial support for slimport anx7625
  2019-10-11  2:20 ` [PATCH v2 0/2] Add initial support for slimport anx7625 Xin Ji
  2019-10-11  2:21   ` [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding Xin Ji
  2019-10-11  2:23   ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Xin Ji
@ 2019-10-11  6:12   ` Andrzej Hajda
  2019-10-11  7:52     ` Xin Ji
  2019-10-11 10:27   ` Dan Carpenter
  3 siblings, 1 reply; 17+ messages in thread
From: Andrzej Hajda @ 2019-10-11  6:12 UTC (permalink / raw)
  To: Xin Ji, devel, Laurent Pinchart
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

On 11.10.2019 04:20, Xin Ji wrote:
> Hi all,
>
> The following series add initial support for the Slimport ANX7625 transmitter, a
> ultra-low power Full-HD 4K MIPI to DP transmitter designed for portable device.
>
> This is the initial version, any mistakes, please let me know, I will fix it in
> the next series.
>
> Thanks,
> Xin


Next time please increment patchset version number - this is third
iteration of v2.


Regards

Andrzej


>
>
> Xin Ji (2):
>   dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
>   drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver
>
>  .../bindings/display/bridge/anx7625.yaml           |   96 +
>  drivers/gpu/drm/bridge/Makefile                    |    2 +-
>  drivers/gpu/drm/bridge/analogix/Kconfig            |    6 +
>  drivers/gpu/drm/bridge/analogix/Makefile           |    1 +
>  drivers/gpu/drm/bridge/analogix/anx7625.c          | 2153 ++++++++++++++++++++
>  drivers/gpu/drm/bridge/analogix/anx7625.h          |  406 ++++
>  6 files changed, 2663 insertions(+), 1 deletion(-)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
>  create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
>  create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h
>

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 0/2] Add initial support for slimport anx7625
  2019-10-11  6:12   ` [PATCH v2 0/2] Add initial support for slimport anx7625 Andrzej Hajda
@ 2019-10-11  7:52     ` Xin Ji
  0 siblings, 0 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-11  7:52 UTC (permalink / raw)
  To: Andrzej Hajda
  Cc: devel, Jernej Skrabec, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Andrzej Hajda,
	Laurent Pinchart, Daniel Vetter, Dan Carpenter, Sheng Pan

Hi Andrzej, OK, I'll increment patchset version number next time.

Thanks,
Xin

On Fri, Oct 11, 2019 at 08:12:53AM +0200, Andrzej Hajda wrote:
> On 11.10.2019 04:20, Xin Ji wrote:
> > Hi all,
> >
> > The following series add initial support for the Slimport ANX7625 transmitter, a
> > ultra-low power Full-HD 4K MIPI to DP transmitter designed for portable device.
> >
> > This is the initial version, any mistakes, please let me know, I will fix it in
> > the next series.
> >
> > Thanks,
> > Xin
> 
> 
> Next time please increment patchset version number - this is third
> iteration of v2.
> 
> 
> Regards
> 
> Andrzej
> 
> 
> >
> >
> > Xin Ji (2):
> >   dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
> >   drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver
> >
> >  .../bindings/display/bridge/anx7625.yaml           |   96 +
> >  drivers/gpu/drm/bridge/Makefile                    |    2 +-
> >  drivers/gpu/drm/bridge/analogix/Kconfig            |    6 +
> >  drivers/gpu/drm/bridge/analogix/Makefile           |    1 +
> >  drivers/gpu/drm/bridge/analogix/anx7625.c          | 2153 ++++++++++++++++++++
> >  drivers/gpu/drm/bridge/analogix/anx7625.h          |  406 ++++
> >  6 files changed, 2663 insertions(+), 1 deletion(-)
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> >  create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
> >  create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h
> >
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 0/2] Add initial support for slimport anx7625
  2019-10-11  2:20 ` [PATCH v2 0/2] Add initial support for slimport anx7625 Xin Ji
                     ` (2 preceding siblings ...)
  2019-10-11  6:12   ` [PATCH v2 0/2] Add initial support for slimport anx7625 Andrzej Hajda
@ 2019-10-11 10:27   ` Dan Carpenter
  3 siblings, 0 replies; 17+ messages in thread
From: Dan Carpenter @ 2019-10-11 10:27 UTC (permalink / raw)
  To: Xin Ji
  Cc: devel, Jernej Skrabec, Nicolas Boichat, Jonas Karlman,
	David Airlie, Neil Armstrong, linux-kernel, dri-devel,
	Andrzej Hajda, Laurent Pinchart, Daniel Vetter, Sheng Pan

On Fri, Oct 11, 2019 at 02:20:47AM +0000, Xin Ji wrote:
> Hi all,
> 
> The following series add initial support for the Slimport ANX7625 transmitter, a
> ultra-low power Full-HD 4K MIPI to DP transmitter designed for portable device.
> 
> This is the initial version, any mistakes, please let me know, I will fix it in
> the next series.
> 
> Thanks,
> Xin
> 

I'm not a domain expert but I like these patches now.

Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>

regards,
dan carpenter

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-11  2:21   ` [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding Xin Ji
@ 2019-10-11 11:21     ` Andrzej Hajda
  2019-10-11 12:54       ` Laurent Pinchart
  2019-10-14  2:53       ` Xin Ji
  0 siblings, 2 replies; 17+ messages in thread
From: Andrzej Hajda @ 2019-10-11 11:21 UTC (permalink / raw)
  To: Xin Ji, devel, Laurent Pinchart
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

On 11.10.2019 04:21, Xin Ji wrote:
> The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> for portable device. It converts MIPI to DisplayPort 1.3 4K.
>
> You can add support to your board with binding.
>
> Example:
> 	anx7625_bridge: encoder@58 {
> 		compatible = "analogix,anx7625";
> 		reg = <0x58>;
> 		status = "okay";
> 		panel-flags = <1>;
> 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> 		#address-cells = <1>;
> 		#size-cells = <0>;
>
> 		port@0 {
> 		  reg = <0>;
> 		  anx_1_in: endpoint {
> 		    remote-endpoint = <&mipi_dsi>;
> 		  };
> 		};
>
> 		port@3 {
> 		  reg = <3>;
> 		  anx_1_out: endpoint {
> 		    remote-endpoint = <&panel_in>;
> 		  };
> 		};
> 	};
>
> Signed-off-by: Xin Ji <xji@analogixsemi.com>
> ---
>  .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
>  1 file changed, 96 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> new file mode 100644
> index 0000000..fc84683
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> @@ -0,0 +1,96 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright 2019 Analogix Semiconductor, Inc.
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> +
> +maintainers:
> +  - Xin Ji <xji@analogixsemi.com>
> +
> +description: |
> +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> +  designed for portable devices.
> +
> +properties:
> +  "#address-cells": true
> +  "#size-cells": true
> +
> +  compatible:
> +    items:
> +      - const: analogix,anx7625
> +
> +  reg:
> +    maxItems: 1
> +
> +  panel-flags:
> +    description: indicate the panel is internal or external
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  enable-gpios:
> +    description: used for power on chip control, POWER_EN pin D2.
> +    maxItems: 1
> +
> +  reset-gpios:
> +    description: used for reset chip control, RESET_N pin B7.
> +    maxItems: 1
> +
> +  port@0:
> +    type: object
> +    description:
> +      A port node pointing to MIPI DSI host port node.
> +
> +  port@1:
> +    type: object
> +    description:
> +      A port node pointing to MIPI DPI host port node.
> +
> +  port@2:
> +    type: object
> +    description:
> +      A port node pointing to external connector port node.
> +
> +  port@3:
> +    type: object
> +    description:
> +      A port node pointing to eDP port node.


Decrypting available product brief[1], there are following physical lines:

Input:

- MIPI DSI/DPI - video data, are DSI and DPI lines shared?

- I2S - audio data,

- I2C - control line,

- ALERT/INTP - interrupt,

- USB 3.1 SSRc/Tx - for USB forwarding,

Output:

- SS1, SS2,

- SBU/AUX,

- CC1/2.


Having this information I try to understand ports defined by you:

- port@2 you have defined as pointing to external port, but here the
port should be rather subnode of ANX7625 - the chip has CC lines, see
beginning of [2].

- port@3 describes SS1, SS2 and SBU/AUX lines together, am I right? In
USB-C binding SBU and SS lines are represented by different ports,
different approach, but maybe better in this case.


Maybe it would be good to add 2nd example with USB-C port.


[1]:
https://www.analogix.com/system/files/AA-002291-PB-6-ANX7625_ProductBrief.pdf

[2]: Documentation/devicetree/bindings/connector/usb-connector.txt


Regards

Andrzej


> +
> +required:
> +  - "#address-cells"
> +  - "#size-cells"
> +  - compatible
> +  - reg
> +  - port@0
> +  - port@3
> +
> +example:
> +  - |
> +    anx7625_bridge: encoder@58 {
> +        compatible = "analogix,anx7625";
> +        reg = <0x58>;
> +        status = "okay";
> +        panel-flags = <1>;
> +        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> +        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        port@0 {
> +          reg = <0>;
> +          anx_1_in: endpoint {
> +            remote-endpoint = <&mipi_dsi>;
> +          };
> +        };
> +
> +        port@3 {
> +          reg = <3>;
> +          anx_1_out: endpoint {
> +            remote-endpoint = <&panel_in>;
> +          };
> +        };
> +    };


_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-11 11:21     ` Andrzej Hajda
@ 2019-10-11 12:54       ` Laurent Pinchart
  2019-10-14  3:02         ` Xin Ji
  2019-10-14  2:53       ` Xin Ji
  1 sibling, 1 reply; 17+ messages in thread
From: Laurent Pinchart @ 2019-10-11 12:54 UTC (permalink / raw)
  To: Andrzej Hajda
  Cc: devel, Jernej Skrabec, Nicolas Boichat, Jonas Karlman,
	David Airlie, Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Xin Ji, Dan Carpenter

Hi Andrzej,

On Fri, Oct 11, 2019 at 01:21:43PM +0200, Andrzej Hajda wrote:
> On 11.10.2019 04:21, Xin Ji wrote:
> > The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> > for portable device. It converts MIPI to DisplayPort 1.3 4K.
> >
> > You can add support to your board with binding.
> >
> > Example:
> > 	anx7625_bridge: encoder@58 {
> > 		compatible = "analogix,anx7625";
> > 		reg = <0x58>;
> > 		status = "okay";
> > 		panel-flags = <1>;
> > 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > 		#address-cells = <1>;
> > 		#size-cells = <0>;
> >
> > 		port@0 {
> > 		  reg = <0>;
> > 		  anx_1_in: endpoint {
> > 		    remote-endpoint = <&mipi_dsi>;
> > 		  };
> > 		};
> >
> > 		port@3 {
> > 		  reg = <3>;
> > 		  anx_1_out: endpoint {
> > 		    remote-endpoint = <&panel_in>;
> > 		  };
> > 		};
> > 	};
> >
> > Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > ---
> >  .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
> >  1 file changed, 96 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > new file mode 100644
> > index 0000000..fc84683
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > @@ -0,0 +1,96 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +# Copyright 2019 Analogix Semiconductor, Inc.
> > +%YAML 1.2
> > +---
> > +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> > +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> > +
> > +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> > +
> > +maintainers:
> > +  - Xin Ji <xji@analogixsemi.com>
> > +
> > +description: |
> > +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> > +  designed for portable devices.
> > +
> > +properties:
> > +  "#address-cells": true
> > +  "#size-cells": true
> > +
> > +  compatible:
> > +    items:
> > +      - const: analogix,anx7625
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  panel-flags:
> > +    description: indicate the panel is internal or external
> > +    maxItems: 1
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  enable-gpios:
> > +    description: used for power on chip control, POWER_EN pin D2.
> > +    maxItems: 1
> > +
> > +  reset-gpios:
> > +    description: used for reset chip control, RESET_N pin B7.
> > +    maxItems: 1
> > +
> > +  port@0:
> > +    type: object
> > +    description:
> > +      A port node pointing to MIPI DSI host port node.
> > +
> > +  port@1:
> > +    type: object
> > +    description:
> > +      A port node pointing to MIPI DPI host port node.
> > +
> > +  port@2:
> > +    type: object
> > +    description:
> > +      A port node pointing to external connector port node.
> > +
> > +  port@3:
> > +    type: object
> > +    description:
> > +      A port node pointing to eDP port node.
> 
> 
> Decrypting available product brief[1], there are following physical lines:
> 
> Input:
> 
> - MIPI DSI/DPI - video data, are DSI and DPI lines shared?

It would be much easier if we could have access to more complete
information. I believe the DSI and DPI pins could be muxed, but there
should be more DPI pins than DSI pins.

> 
> - I2S - audio data,
> 
> - I2C - control line,
> 
> - ALERT/INTP - interrupt,
> 
> - USB 3.1 SSRc/Tx - for USB forwarding,
> 
> Output:
> 
> - SS1, SS2,
> 
> - SBU/AUX,
> 
> - CC1/2.
> 
> 
> Having this information I try to understand ports defined by you:
> 
> - port@2 you have defined as pointing to external port, but here the
> port should be rather subnode of ANX7625 - the chip has CC lines, see
> beginning of [2].
> 
> - port@3 describes SS1, SS2 and SBU/AUX lines together, am I right? In
> USB-C binding SBU and SS lines are represented by different ports,
> different approach, but maybe better in this case.

I believe that, when connected to a DP display (either DP or eDP), the
DisplayPort signals are output on SS1 and/or SS2. I this really wonder
if we need two separate ports for this, it seems that port@2 and port@3
should be merged.

> Maybe it would be good to add 2nd example with USB-C port.

That would help with the discussion, yes.

> [1]:
> https://www.analogix.com/system/files/AA-002291-PB-6-ANX7625_ProductBrief.pdf
> 
> [2]: Documentation/devicetree/bindings/connector/usb-connector.txt
> 
> > +
> > +required:
> > +  - "#address-cells"
> > +  - "#size-cells"
> > +  - compatible
> > +  - reg
> > +  - port@0
> > +  - port@3
> > +
> > +example:
> > +  - |
> > +    anx7625_bridge: encoder@58 {
> > +        compatible = "analogix,anx7625";
> > +        reg = <0x58>;
> > +        status = "okay";
> > +        panel-flags = <1>;
> > +        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > +        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        port@0 {
> > +          reg = <0>;
> > +          anx_1_in: endpoint {
> > +            remote-endpoint = <&mipi_dsi>;
> > +          };
> > +        };
> > +
> > +        port@3 {
> > +          reg = <3>;
> > +          anx_1_out: endpoint {
> > +            remote-endpoint = <&panel_in>;
> > +          };
> > +        };
> > +    };

-- 
Regards,

Laurent Pinchart
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-11 11:21     ` Andrzej Hajda
  2019-10-11 12:54       ` Laurent Pinchart
@ 2019-10-14  2:53       ` Xin Ji
  1 sibling, 0 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-14  2:53 UTC (permalink / raw)
  To: Andrzej Hajda
  Cc: devel, Jernej Skrabec, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Laurent Pinchart,
	Daniel Vetter, Dan Carpenter, Sheng Pan

Hi Andrzej Hajda, please check my comment below.

Thanks,
Xin

On Fri, Oct 11, 2019 at 01:21:43PM +0200, Andrzej Hajda wrote:
> On 11.10.2019 04:21, Xin Ji wrote:
> > The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> > for portable device. It converts MIPI to DisplayPort 1.3 4K.
> >
> > You can add support to your board with binding.
> >
> > Example:
> > 	anx7625_bridge: encoder@58 {
> > 		compatible = "analogix,anx7625";
> > 		reg = <0x58>;
> > 		status = "okay";
> > 		panel-flags = <1>;
> > 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > 		#address-cells = <1>;
> > 		#size-cells = <0>;
> >
> > 		port@0 {
> > 		  reg = <0>;
> > 		  anx_1_in: endpoint {
> > 		    remote-endpoint = <&mipi_dsi>;
> > 		  };
> > 		};
> >
> > 		port@3 {
> > 		  reg = <3>;
> > 		  anx_1_out: endpoint {
> > 		    remote-endpoint = <&panel_in>;
> > 		  };
> > 		};
> > 	};
> >
> > Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > ---
> >  .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
> >  1 file changed, 96 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > new file mode 100644
> > index 0000000..fc84683
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > @@ -0,0 +1,96 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +# Copyright 2019 Analogix Semiconductor, Inc.
> > +%YAML 1.2
> > +---
> > +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> > +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> > +
> > +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> > +
> > +maintainers:
> > +  - Xin Ji <xji@analogixsemi.com>
> > +
> > +description: |
> > +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> > +  designed for portable devices.
> > +
> > +properties:
> > +  "#address-cells": true
> > +  "#size-cells": true
> > +
> > +  compatible:
> > +    items:
> > +      - const: analogix,anx7625
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  panel-flags:
> > +    description: indicate the panel is internal or external
> > +    maxItems: 1
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  enable-gpios:
> > +    description: used for power on chip control, POWER_EN pin D2.
> > +    maxItems: 1
> > +
> > +  reset-gpios:
> > +    description: used for reset chip control, RESET_N pin B7.
> > +    maxItems: 1
> > +
> > +  port@0:
> > +    type: object
> > +    description:
> > +      A port node pointing to MIPI DSI host port node.
> > +
> > +  port@1:
> > +    type: object
> > +    description:
> > +      A port node pointing to MIPI DPI host port node.
> > +
> > +  port@2:
> > +    type: object
> > +    description:
> > +      A port node pointing to external connector port node.
> > +
> > +  port@3:
> > +    type: object
> > +    description:
> > +      A port node pointing to eDP port node.
> 
> 
> Decrypting available product brief[1], there are following physical lines:
> 
> Input:
> 
> - MIPI DSI/DPI - video data, are DSI and DPI lines shared?
> 
> - I2S - audio data,
> 
> - I2C - control line,
> 
> - ALERT/INTP - interrupt,
> 
> - USB 3.1 SSRc/Tx - for USB forwarding,
> 
> Output:
> 
> - SS1, SS2,
> 
> - SBU/AUX,
> 
> - CC1/2.
At this application, we didn't use CC1/2 line, we only use the video
format convert(MIPI to DP) feature on anx7625.
> 
> 
> Having this information I try to understand ports defined by you:
> 
> - port@2 you have defined as pointing to external port, but here the
> port should be rather subnode of ANX7625 - the chip has CC lines, see
> beginning of [2].
The port@2 is for Chromium book external port low power mode control,
the driver according this port to register external connector
notify interface to receive "connect/disconnect" event to do low power
control.
> 
> - port@3 describes SS1, SS2 and SBU/AUX lines together, am I right? In
> USB-C binding SBU and SS lines are represented by different ports,
> different approach, but maybe better in this case.
> 
> 
> Maybe it would be good to add 2nd example with USB-C port.
No need to add 2nd example with USB-C port, as I said, we didn't use the
USB Type-C PD feature at anx7625.
> 
> 
> [1]:
> https://www.analogix.com/system/files/AA-002291-PB-6-ANX7625_ProductBrief.pdf
> 
> [2]: Documentation/devicetree/bindings/connector/usb-connector.txt
> 
> 
> Regards
> 
> Andrzej
> 
> 
> > +
> > +required:
> > +  - "#address-cells"
> > +  - "#size-cells"
> > +  - compatible
> > +  - reg
> > +  - port@0
> > +  - port@3
> > +
> > +example:
> > +  - |
> > +    anx7625_bridge: encoder@58 {
> > +        compatible = "analogix,anx7625";
> > +        reg = <0x58>;
> > +        status = "okay";
> > +        panel-flags = <1>;
> > +        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > +        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        port@0 {
> > +          reg = <0>;
> > +          anx_1_in: endpoint {
> > +            remote-endpoint = <&mipi_dsi>;
> > +          };
> > +        };
> > +
> > +        port@3 {
> > +          reg = <3>;
> > +          anx_1_out: endpoint {
> > +            remote-endpoint = <&panel_in>;
> > +          };
> > +        };
> > +    };
> 
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-11 12:54       ` Laurent Pinchart
@ 2019-10-14  3:02         ` Xin Ji
  2019-10-14 22:16           ` Laurent Pinchart
  0 siblings, 1 reply; 17+ messages in thread
From: Xin Ji @ 2019-10-14  3:02 UTC (permalink / raw)
  To: Laurent Pinchart
  Cc: devel, Jernej Skrabec, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Andrzej Hajda,
	Laurent Pinchart, Daniel Vetter, Dan Carpenter, Sheng Pan

Hi Laurent Pinchart, please check my comment below.

Thanks,
Xin

On Fri, Oct 11, 2019 at 03:54:18PM +0300, Laurent Pinchart wrote:
> Hi Andrzej,
> 
> On Fri, Oct 11, 2019 at 01:21:43PM +0200, Andrzej Hajda wrote:
> > On 11.10.2019 04:21, Xin Ji wrote:
> > > The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> > > for portable device. It converts MIPI to DisplayPort 1.3 4K.
> > >
> > > You can add support to your board with binding.
> > >
> > > Example:
> > > 	anx7625_bridge: encoder@58 {
> > > 		compatible = "analogix,anx7625";
> > > 		reg = <0x58>;
> > > 		status = "okay";
> > > 		panel-flags = <1>;
> > > 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > > 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > > 		#address-cells = <1>;
> > > 		#size-cells = <0>;
> > >
> > > 		port@0 {
> > > 		  reg = <0>;
> > > 		  anx_1_in: endpoint {
> > > 		    remote-endpoint = <&mipi_dsi>;
> > > 		  };
> > > 		};
> > >
> > > 		port@3 {
> > > 		  reg = <3>;
> > > 		  anx_1_out: endpoint {
> > > 		    remote-endpoint = <&panel_in>;
> > > 		  };
> > > 		};
> > > 	};
> > >
> > > Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > > ---
> > >  .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
> > >  1 file changed, 96 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > > new file mode 100644
> > > index 0000000..fc84683
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > > @@ -0,0 +1,96 @@
> > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > +# Copyright 2019 Analogix Semiconductor, Inc.
> > > +%YAML 1.2
> > > +---
> > > +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> > > +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> > > +
> > > +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> > > +
> > > +maintainers:
> > > +  - Xin Ji <xji@analogixsemi.com>
> > > +
> > > +description: |
> > > +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> > > +  designed for portable devices.
> > > +
> > > +properties:
> > > +  "#address-cells": true
> > > +  "#size-cells": true
> > > +
> > > +  compatible:
> > > +    items:
> > > +      - const: analogix,anx7625
> > > +
> > > +  reg:
> > > +    maxItems: 1
> > > +
> > > +  panel-flags:
> > > +    description: indicate the panel is internal or external
> > > +    maxItems: 1
> > > +
> > > +  interrupts:
> > > +    maxItems: 1
> > > +
> > > +  enable-gpios:
> > > +    description: used for power on chip control, POWER_EN pin D2.
> > > +    maxItems: 1
> > > +
> > > +  reset-gpios:
> > > +    description: used for reset chip control, RESET_N pin B7.
> > > +    maxItems: 1
> > > +
> > > +  port@0:
> > > +    type: object
> > > +    description:
> > > +      A port node pointing to MIPI DSI host port node.
> > > +
> > > +  port@1:
> > > +    type: object
> > > +    description:
> > > +      A port node pointing to MIPI DPI host port node.
> > > +
> > > +  port@2:
> > > +    type: object
> > > +    description:
> > > +      A port node pointing to external connector port node.
> > > +
> > > +  port@3:
> > > +    type: object
> > > +    description:
> > > +      A port node pointing to eDP port node.
> > 
> > 
> > Decrypting available product brief[1], there are following physical lines:
> > 
> > Input:
> > 
> > - MIPI DSI/DPI - video data, are DSI and DPI lines shared?
> 
> It would be much easier if we could have access to more complete
> information. I believe the DSI and DPI pins could be muxed, but there
> should be more DPI pins than DSI pins.
Yes DPI pins more than DSI pins.
> 
> > 
> > - I2S - audio data,
> > 
> > - I2C - control line,
> > 
> > - ALERT/INTP - interrupt,
> > 
> > - USB 3.1 SSRc/Tx - for USB forwarding,
> > 
> > Output:
> > 
> > - SS1, SS2,
> > 
> > - SBU/AUX,
> > 
> > - CC1/2.
> > 
> > 
> > Having this information I try to understand ports defined by you:
> > 
> > - port@2 you have defined as pointing to external port, but here the
> > port should be rather subnode of ANX7625 - the chip has CC lines, see
> > beginning of [2].
> > 
> > - port@3 describes SS1, SS2 and SBU/AUX lines together, am I right? In
> > USB-C binding SBU and SS lines are represented by different ports,
> > different approach, but maybe better in this case.
> 
> I believe that, when connected to a DP display (either DP or eDP), the
> DisplayPort signals are output on SS1 and/or SS2. I this really wonder
> if we need two separate ports for this, it seems that port@2 and port@3
> should be merged.
OK, I will merge the port@2 and port@3, and use a flag to indicate
whether the control is external connector control or not.
> 
> > Maybe it would be good to add 2nd example with USB-C port.
> 
> That would help with the discussion, yes.
As we disabled USB-C feature in anx7625, we cannot define a USB-C port.
> 
> > [1]:
> > https://www.analogix.com/system/files/AA-002291-PB-6-ANX7625_ProductBrief.pdf
> > 
> > [2]: Documentation/devicetree/bindings/connector/usb-connector.txt
> > 
> > > +
> > > +required:
> > > +  - "#address-cells"
> > > +  - "#size-cells"
> > > +  - compatible
> > > +  - reg
> > > +  - port@0
> > > +  - port@3
> > > +
> > > +example:
> > > +  - |
> > > +    anx7625_bridge: encoder@58 {
> > > +        compatible = "analogix,anx7625";
> > > +        reg = <0x58>;
> > > +        status = "okay";
> > > +        panel-flags = <1>;
> > > +        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > > +        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > > +        #address-cells = <1>;
> > > +        #size-cells = <0>;
> > > +
> > > +        port@0 {
> > > +          reg = <0>;
> > > +          anx_1_in: endpoint {
> > > +            remote-endpoint = <&mipi_dsi>;
> > > +          };
> > > +        };
> > > +
> > > +        port@3 {
> > > +          reg = <3>;
> > > +          anx_1_out: endpoint {
> > > +            remote-endpoint = <&panel_in>;
> > > +          };
> > > +        };
> > > +    };
> 
> -- 
> Regards,
> 
> Laurent Pinchart
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver
  2019-10-11  2:23   ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Xin Ji
@ 2019-10-14  8:20     ` kbuild test robot
  2019-10-14  8:20     ` [RFC PATCH] drm/bridge: anx7625: ANX_OUI[] can be static kbuild test robot
  2019-10-15  9:19     ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Dan Carpenter
  2 siblings, 0 replies; 17+ messages in thread
From: kbuild test robot @ 2019-10-14  8:20 UTC (permalink / raw)
  To: Xin Ji
  Cc: devel, Jernej Skrabec, Nicolas Boichat, kbuild-all,
	Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel,
	dri-devel, Andrzej Hajda, Laurent Pinchart, Daniel Vetter,
	Dan Carpenter, Sheng Pan

Hi Xin,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on linus/master]
[cannot apply to v5.4-rc3 next-20191011]
[if your patch is applied to the wrong git tree, please drop us a note to help
improve the system. BTW, we also suggest to use '--base' option to specify the
base tree in git format-patch, please see https://stackoverflow.com/a/37406982]

url:    https://github.com/0day-ci/linux/commits/Xin-Ji/dt-bindings-drm-bridge-anx7625-MIPI-to-DP-transmitter-binding/20191014-043019
reproduce:
        # apt-get install sparse
        # sparse version: v0.6.1-rc1-43-g0ccb3b4-dirty
        make ARCH=x86_64 allmodconfig
        make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'

If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>


sparse warnings: (new ones prefixed by >>)

>> drivers/gpu/drm/bridge/analogix/anx7625.c:731:10: sparse: sparse: symbol 'ANX_OUI' was not declared. Should it be static?

Please review and possibly fold the followup patch.

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* [RFC PATCH] drm/bridge: anx7625: ANX_OUI[] can be static
  2019-10-11  2:23   ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Xin Ji
  2019-10-14  8:20     ` kbuild test robot
@ 2019-10-14  8:20     ` kbuild test robot
  2019-10-15  9:19     ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Dan Carpenter
  2 siblings, 0 replies; 17+ messages in thread
From: kbuild test robot @ 2019-10-14  8:20 UTC (permalink / raw)
  To: Xin Ji
  Cc: devel, Jernej Skrabec, Nicolas Boichat, kbuild-all,
	Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel,
	dri-devel, Andrzej Hajda, Laurent Pinchart, Daniel Vetter,
	Dan Carpenter, Sheng Pan


Fixes: 152a82b6747f ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver")
Signed-off-by: kbuild test robot <lkp@intel.com>
---
 anx7625.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 96adf3b89d7f0..a261f4d31ea88 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -728,7 +728,7 @@ static int anx7625_dpi_config(struct anx7625_data *ctx)
 	return ret;
 }
 
-const u8 ANX_OUI[3] = { 0x00, 0x22, 0xB9 };
+static const u8 ANX_OUI[3] = { 0x00, 0x22, 0xB9 };
 static int is_anx_dongle(struct anx7625_data *ctx)
 {
 	u8 buf[3];
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-14  3:02         ` Xin Ji
@ 2019-10-14 22:16           ` Laurent Pinchart
  2019-10-15  3:02             ` Xin Ji
  0 siblings, 1 reply; 17+ messages in thread
From: Laurent Pinchart @ 2019-10-14 22:16 UTC (permalink / raw)
  To: Xin Ji
  Cc: devel, Jernej Skrabec, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Andrzej Hajda,
	Sheng Pan, Daniel Vetter, Dan Carpenter

Hi Xin Ji,

On Mon, Oct 14, 2019 at 03:02:48AM +0000, Xin Ji wrote:
> On Fri, Oct 11, 2019 at 03:54:18PM +0300, Laurent Pinchart wrote:
> > On Fri, Oct 11, 2019 at 01:21:43PM +0200, Andrzej Hajda wrote:
> >> On 11.10.2019 04:21, Xin Ji wrote:
> >>> The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> >>> for portable device. It converts MIPI to DisplayPort 1.3 4K.
> >>>
> >>> You can add support to your board with binding.
> >>>
> >>> Example:
> >>> 	anx7625_bridge: encoder@58 {
> >>> 		compatible = "analogix,anx7625";
> >>> 		reg = <0x58>;
> >>> 		status = "okay";
> >>> 		panel-flags = <1>;
> >>> 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> >>> 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> >>> 		#address-cells = <1>;
> >>> 		#size-cells = <0>;
> >>>
> >>> 		port@0 {
> >>> 		  reg = <0>;
> >>> 		  anx_1_in: endpoint {
> >>> 		    remote-endpoint = <&mipi_dsi>;
> >>> 		  };
> >>> 		};
> >>>
> >>> 		port@3 {
> >>> 		  reg = <3>;
> >>> 		  anx_1_out: endpoint {
> >>> 		    remote-endpoint = <&panel_in>;
> >>> 		  };
> >>> 		};
> >>> 	};
> >>>
> >>> Signed-off-by: Xin Ji <xji@analogixsemi.com>
> >>> ---
> >>>  .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
> >>>  1 file changed, 96 insertions(+)
> >>>  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> >>>
> >>> diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> >>> new file mode 100644
> >>> index 0000000..fc84683
> >>> --- /dev/null
> >>> +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> >>> @@ -0,0 +1,96 @@
> >>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> >>> +# Copyright 2019 Analogix Semiconductor, Inc.
> >>> +%YAML 1.2
> >>> +---
> >>> +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> >>> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> >>> +
> >>> +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> >>> +
> >>> +maintainers:
> >>> +  - Xin Ji <xji@analogixsemi.com>
> >>> +
> >>> +description: |
> >>> +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> >>> +  designed for portable devices.
> >>> +
> >>> +properties:
> >>> +  "#address-cells": true
> >>> +  "#size-cells": true
> >>> +
> >>> +  compatible:
> >>> +    items:
> >>> +      - const: analogix,anx7625
> >>> +
> >>> +  reg:
> >>> +    maxItems: 1
> >>> +
> >>> +  panel-flags:
> >>> +    description: indicate the panel is internal or external
> >>> +    maxItems: 1
> >>> +
> >>> +  interrupts:
> >>> +    maxItems: 1
> >>> +
> >>> +  enable-gpios:
> >>> +    description: used for power on chip control, POWER_EN pin D2.
> >>> +    maxItems: 1
> >>> +
> >>> +  reset-gpios:
> >>> +    description: used for reset chip control, RESET_N pin B7.
> >>> +    maxItems: 1
> >>> +
> >>> +  port@0:
> >>> +    type: object
> >>> +    description:
> >>> +      A port node pointing to MIPI DSI host port node.
> >>> +
> >>> +  port@1:
> >>> +    type: object
> >>> +    description:
> >>> +      A port node pointing to MIPI DPI host port node.
> >>> +
> >>> +  port@2:
> >>> +    type: object
> >>> +    description:
> >>> +      A port node pointing to external connector port node.
> >>> +
> >>> +  port@3:
> >>> +    type: object
> >>> +    description:
> >>> +      A port node pointing to eDP port node.
> >> 
> >> 
> >> Decrypting available product brief[1], there are following physical lines:
> >> 
> >> Input:
> >> 
> >> - MIPI DSI/DPI - video data, are DSI and DPI lines shared?
> > 
> > It would be much easier if we could have access to more complete
> > information. I believe the DSI and DPI pins could be muxed, but there
> > should be more DPI pins than DSI pins.
>
> Yes DPI pins more than DSI pins.
> 
> >> 
> >> - I2S - audio data,
> >> 
> >> - I2C - control line,
> >> 
> >> - ALERT/INTP - interrupt,
> >> 
> >> - USB 3.1 SSRc/Tx - for USB forwarding,
> >> 
> >> Output:
> >> 
> >> - SS1, SS2,
> >> 
> >> - SBU/AUX,
> >> 
> >> - CC1/2.
> >> 
> >> 
> >> Having this information I try to understand ports defined by you:
> >> 
> >> - port@2 you have defined as pointing to external port, but here the
> >> port should be rather subnode of ANX7625 - the chip has CC lines, see
> >> beginning of [2].
> >> 
> >> - port@3 describes SS1, SS2 and SBU/AUX lines together, am I right? In
> >> USB-C binding SBU and SS lines are represented by different ports,
> >> different approach, but maybe better in this case.
> > 
> > I believe that, when connected to a DP display (either DP or eDP), the
> > DisplayPort signals are output on SS1 and/or SS2. I this really wonder
> > if we need two separate ports for this, it seems that port@2 and port@3
> > should be merged.
>
> OK, I will merge the port@2 and port@3, and use a flag to indicate
> whether the control is external connector control or not.

Could this be inferred from the connected DT node ? If the node
connected to the endpoint is a display connector node, then we have an
external connector. Otherwise we have an eDP panel. Ideally this should
even be done at runtime, by communicating with the drm_bridge or
drm_panel corresponding to the connected node.

> >> Maybe it would be good to add 2nd example with USB-C port.
> > 
> > That would help with the discussion, yes.
>
> As we disabled USB-C feature in anx7625, we cannot define a USB-C port.

It's fine if the feature isn't implemented in the driver, but we should
still take it into account to design the DT bindings. Otherwise, when
someone will want to add support for USB-C to the ANX7625 bindings, they
may find it impossible to do so in a nice backward-compatible way.
That's why an example would already be useful.

> >> [1]:
> >> https://www.analogix.com/system/files/AA-002291-PB-6-ANX7625_ProductBrief.pdf
> >> 
> >> [2]: Documentation/devicetree/bindings/connector/usb-connector.txt
> >> 
> >>> +
> >>> +required:
> >>> +  - "#address-cells"
> >>> +  - "#size-cells"
> >>> +  - compatible
> >>> +  - reg
> >>> +  - port@0
> >>> +  - port@3
> >>> +
> >>> +example:
> >>> +  - |
> >>> +    anx7625_bridge: encoder@58 {
> >>> +        compatible = "analogix,anx7625";
> >>> +        reg = <0x58>;
> >>> +        status = "okay";
> >>> +        panel-flags = <1>;
> >>> +        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> >>> +        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> >>> +        #address-cells = <1>;
> >>> +        #size-cells = <0>;
> >>> +
> >>> +        port@0 {
> >>> +          reg = <0>;
> >>> +          anx_1_in: endpoint {
> >>> +            remote-endpoint = <&mipi_dsi>;
> >>> +          };
> >>> +        };
> >>> +
> >>> +        port@3 {
> >>> +          reg = <3>;
> >>> +          anx_1_out: endpoint {
> >>> +            remote-endpoint = <&panel_in>;
> >>> +          };
> >>> +        };
> >>> +    };

-- 
Regards,

Laurent Pinchart
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  2019-10-14 22:16           ` Laurent Pinchart
@ 2019-10-15  3:02             ` Xin Ji
  0 siblings, 0 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-15  3:02 UTC (permalink / raw)
  To: Laurent Pinchart
  Cc: devel, Jernej Skrabec, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Andrzej Hajda,
	Laurent Pinchart, Daniel Vetter, Dan Carpenter, Sheng Pan

Hi Laurent Pinchart,

On Tue, Oct 15, 2019 at 01:16:10AM +0300, Laurent Pinchart wrote:
> Hi Xin Ji,
> 
> On Mon, Oct 14, 2019 at 03:02:48AM +0000, Xin Ji wrote:
> > On Fri, Oct 11, 2019 at 03:54:18PM +0300, Laurent Pinchart wrote:
> > > On Fri, Oct 11, 2019 at 01:21:43PM +0200, Andrzej Hajda wrote:
> > >> On 11.10.2019 04:21, Xin Ji wrote:
> > >>> The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
> > >>> for portable device. It converts MIPI to DisplayPort 1.3 4K.
> > >>>
> > >>> You can add support to your board with binding.
> > >>>
> > >>> Example:
> > >>> 	anx7625_bridge: encoder@58 {
> > >>> 		compatible = "analogix,anx7625";
> > >>> 		reg = <0x58>;
> > >>> 		status = "okay";
> > >>> 		panel-flags = <1>;
> > >>> 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > >>> 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > >>> 		#address-cells = <1>;
> > >>> 		#size-cells = <0>;
> > >>>
> > >>> 		port@0 {
> > >>> 		  reg = <0>;
> > >>> 		  anx_1_in: endpoint {
> > >>> 		    remote-endpoint = <&mipi_dsi>;
> > >>> 		  };
> > >>> 		};
> > >>>
> > >>> 		port@3 {
> > >>> 		  reg = <3>;
> > >>> 		  anx_1_out: endpoint {
> > >>> 		    remote-endpoint = <&panel_in>;
> > >>> 		  };
> > >>> 		};
> > >>> 	};
> > >>>
> > >>> Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > >>> ---
> > >>>  .../bindings/display/bridge/anx7625.yaml           | 96 ++++++++++++++++++++++
> > >>>  1 file changed, 96 insertions(+)
> > >>>  create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > >>>
> > >>> diff --git a/Documentation/devicetree/bindings/display/bridge/anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > >>> new file mode 100644
> > >>> index 0000000..fc84683
> > >>> --- /dev/null
> > >>> +++ b/Documentation/devicetree/bindings/display/bridge/anx7625.yaml
> > >>> @@ -0,0 +1,96 @@
> > >>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > >>> +# Copyright 2019 Analogix Semiconductor, Inc.
> > >>> +%YAML 1.2
> > >>> +---
> > >>> +$id: "http://devicetree.org/schemas/display/bridge/anx7625.yaml#"
> > >>> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> > >>> +
> > >>> +title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
> > >>> +
> > >>> +maintainers:
> > >>> +  - Xin Ji <xji@analogixsemi.com>
> > >>> +
> > >>> +description: |
> > >>> +  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
> > >>> +  designed for portable devices.
> > >>> +
> > >>> +properties:
> > >>> +  "#address-cells": true
> > >>> +  "#size-cells": true
> > >>> +
> > >>> +  compatible:
> > >>> +    items:
> > >>> +      - const: analogix,anx7625
> > >>> +
> > >>> +  reg:
> > >>> +    maxItems: 1
> > >>> +
> > >>> +  panel-flags:
> > >>> +    description: indicate the panel is internal or external
> > >>> +    maxItems: 1
> > >>> +
> > >>> +  interrupts:
> > >>> +    maxItems: 1
> > >>> +
> > >>> +  enable-gpios:
> > >>> +    description: used for power on chip control, POWER_EN pin D2.
> > >>> +    maxItems: 1
> > >>> +
> > >>> +  reset-gpios:
> > >>> +    description: used for reset chip control, RESET_N pin B7.
> > >>> +    maxItems: 1
> > >>> +
> > >>> +  port@0:
> > >>> +    type: object
> > >>> +    description:
> > >>> +      A port node pointing to MIPI DSI host port node.
> > >>> +
> > >>> +  port@1:
> > >>> +    type: object
> > >>> +    description:
> > >>> +      A port node pointing to MIPI DPI host port node.
> > >>> +
> > >>> +  port@2:
> > >>> +    type: object
> > >>> +    description:
> > >>> +      A port node pointing to external connector port node.
> > >>> +
> > >>> +  port@3:
> > >>> +    type: object
> > >>> +    description:
> > >>> +      A port node pointing to eDP port node.
> > >> 
> > >> 
> > >> Decrypting available product brief[1], there are following physical lines:
> > >> 
> > >> Input:
> > >> 
> > >> - MIPI DSI/DPI - video data, are DSI and DPI lines shared?
> > > 
> > > It would be much easier if we could have access to more complete
> > > information. I believe the DSI and DPI pins could be muxed, but there
> > > should be more DPI pins than DSI pins.
> >
> > Yes DPI pins more than DSI pins.
> > 
> > >> 
> > >> - I2S - audio data,
> > >> 
> > >> - I2C - control line,
> > >> 
> > >> - ALERT/INTP - interrupt,
> > >> 
> > >> - USB 3.1 SSRc/Tx - for USB forwarding,
> > >> 
> > >> Output:
> > >> 
> > >> - SS1, SS2,
> > >> 
> > >> - SBU/AUX,
> > >> 
> > >> - CC1/2.
> > >> 
> > >> 
> > >> Having this information I try to understand ports defined by you:
> > >> 
> > >> - port@2 you have defined as pointing to external port, but here the
> > >> port should be rather subnode of ANX7625 - the chip has CC lines, see
> > >> beginning of [2].
> > >> 
> > >> - port@3 describes SS1, SS2 and SBU/AUX lines together, am I right? In
> > >> USB-C binding SBU and SS lines are represented by different ports,
> > >> different approach, but maybe better in this case.
> > > 
> > > I believe that, when connected to a DP display (either DP or eDP), the
> > > DisplayPort signals are output on SS1 and/or SS2. I this really wonder
> > > if we need two separate ports for this, it seems that port@2 and port@3
> > > should be merged.
> >
> > OK, I will merge the port@2 and port@3, and use a flag to indicate
> > whether the control is external connector control or not.
> 
> Could this be inferred from the connected DT node ? If the node
> connected to the endpoint is a display connector node, then we have an
> external connector. Otherwise we have an eDP panel. Ideally this should
> even be done at runtime, by communicating with the drm_bridge or
> drm_panel corresponding to the connected node.

I think the port@2 should be removed, it could not be inferred from the
connected DT node.

> 
> > >> Maybe it would be good to add 2nd example with USB-C port.
> > > 
> > > That would help with the discussion, yes.
> >
> > As we disabled USB-C feature in anx7625, we cannot define a USB-C port.
> 
> It's fine if the feature isn't implemented in the driver, but we should
> still take it into account to design the DT bindings. Otherwise, when
> someone will want to add support for USB-C to the ANX7625 bindings, they
> may find it impossible to do so in a nice backward-compatible way.
> That's why an example would already be useful.
OK.
> 
> > >> [1]:
> > >> https://www.analogix.com/system/files/AA-002291-PB-6-ANX7625_ProductBrief.pdf
> > >> 
> > >> [2]: Documentation/devicetree/bindings/connector/usb-connector.txt
> > >> 
> > >>> +
> > >>> +required:
> > >>> +  - "#address-cells"
> > >>> +  - "#size-cells"
> > >>> +  - compatible
> > >>> +  - reg
> > >>> +  - port@0
> > >>> +  - port@3
> > >>> +
> > >>> +example:
> > >>> +  - |
> > >>> +    anx7625_bridge: encoder@58 {
> > >>> +        compatible = "analogix,anx7625";
> > >>> +        reg = <0x58>;
> > >>> +        status = "okay";
> > >>> +        panel-flags = <1>;
> > >>> +        enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
> > >>> +        reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
> > >>> +        #address-cells = <1>;
> > >>> +        #size-cells = <0>;
> > >>> +
> > >>> +        port@0 {
> > >>> +          reg = <0>;
> > >>> +          anx_1_in: endpoint {
> > >>> +            remote-endpoint = <&mipi_dsi>;
> > >>> +          };
> > >>> +        };
> > >>> +
> > >>> +        port@3 {
> > >>> +          reg = <3>;
> > >>> +          anx_1_out: endpoint {
> > >>> +            remote-endpoint = <&panel_in>;
> > >>> +          };
> > >>> +        };
> > >>> +    };
> 
> -- 
> Regards,
> 
> Laurent Pinchart
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* Re: [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver
  2019-10-11  2:23   ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Xin Ji
  2019-10-14  8:20     ` kbuild test robot
  2019-10-14  8:20     ` [RFC PATCH] drm/bridge: anx7625: ANX_OUI[] can be static kbuild test robot
@ 2019-10-15  9:19     ` Dan Carpenter
  2 siblings, 0 replies; 17+ messages in thread
From: Dan Carpenter @ 2019-10-15  9:19 UTC (permalink / raw)
  To: kbuild, Xin Ji
  Cc: devel, Jernej Skrabec, Nicolas Boichat, kbuild-all,
	Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel,
	dri-devel, Andrzej Hajda, Laurent Pinchart, Daniel Vetter,
	Dan Carpenter, Sheng Pan

[  These are automated text from the 0-day bot -dan ]

Hi Xin,

Thank you for the patch! Perhaps something to improve:

url:    https://github.com/0day-ci/linux/commits/Xin-Ji/dt-bindings-drm-bridge-anx7625-MIPI-to-DP-transmitter-binding/20191014-043019

If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>

New smatch warnings:
drivers/gpu/drm/bridge/analogix/anx7625.c:1274 anx7625_start_dp_work() error: uninitialized symbol 'sp_tx_lane_count'.

# https://github.com/0day-ci/linux/commit/152a82b6747f10d6c13c7a422173947c2f2e1aa2
git remote add linux-review https://github.com/0day-ci/linux
git remote update linux-review
git checkout 152a82b6747f10d6c13c7a422173947c2f2e1aa2
vim +/sp_tx_lane_count +1274 drivers/gpu/drm/bridge/analogix/anx7625.c

152a82b6747f10 Xin Ji 2019-10-11  1253  static void anx7625_start_dp_work(struct anx7625_data *ctx)
152a82b6747f10 Xin Ji 2019-10-11  1254  {
152a82b6747f10 Xin Ji 2019-10-11  1255  	int ret;
152a82b6747f10 Xin Ji 2019-10-11  1256  	u8 buf[MAX_DPCD_BUFFER_SIZE];
152a82b6747f10 Xin Ji 2019-10-11  1257  	u8 hdcp_cap;
152a82b6747f10 Xin Ji 2019-10-11  1258  	struct device *dev = &ctx->client->dev;
152a82b6747f10 Xin Ji 2019-10-11  1259  	u8 sp_tx_bw; /* linktraining banwidth */
152a82b6747f10 Xin Ji 2019-10-11  1260  	u8 sp_tx_lane_count; /* link training lane count */
152a82b6747f10 Xin Ji 2019-10-11  1261  
152a82b6747f10 Xin Ji 2019-10-11  1262  	if (ctx->hpd_high_cnt >= 2) {
152a82b6747f10 Xin Ji 2019-10-11  1263  		DRM_DEV_DEBUG_DRIVER(dev, "anx7625 filter useless HPD\n");
152a82b6747f10 Xin Ji 2019-10-11  1264  		return;
152a82b6747f10 Xin Ji 2019-10-11  1265  	}
152a82b6747f10 Xin Ji 2019-10-11  1266  
152a82b6747f10 Xin Ji 2019-10-11  1267  	ctx->hpd_high_cnt++;
152a82b6747f10 Xin Ji 2019-10-11  1268  
152a82b6747f10 Xin Ji 2019-10-11  1269  	sp_tx_get_rx_bw(ctx, &sp_tx_bw);
152a82b6747f10 Xin Ji 2019-10-11  1270  
152a82b6747f10 Xin Ji 2019-10-11  1271  	sp_tx_aux_dpcdread_bytes(ctx, 0x00, 0x00, DPCD_MAX_LANE_COUNT,
152a82b6747f10 Xin Ji 2019-10-11  1272  				 1, &sp_tx_lane_count);
                                                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Smatch thinks sp_tx_aux_dpcdread_bytes() can fail and we don't check
for errors.

152a82b6747f10 Xin Ji 2019-10-11  1273  
152a82b6747f10 Xin Ji 2019-10-11 @1274  	sp_tx_lane_count = sp_tx_lane_count & 0x1f;
152a82b6747f10 Xin Ji 2019-10-11  1275  	sp_tx_aux_dpcdread_bytes(ctx, 0x06, 0x80, 0x28, 1, buf);/* read Bcap */
152a82b6747f10 Xin Ji 2019-10-11  1276  
152a82b6747f10 Xin Ji 2019-10-11  1277  	hdcp_cap = buf[0] & 0x01;
152a82b6747f10 Xin Ji 2019-10-11  1278  

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v2 0/2] Add initial support for slimport anx7625
@ 2019-10-10  9:31 Xin Ji
  0 siblings, 0 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-10  9:31 UTC (permalink / raw)
  To: devel, Laurent Pinchart, Andrzej Hajda
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

Hi all,

The following series add initial support for the Slimport ANX7625 transmitter, a
ultra-low power Full-HD 4K MIPI to DP transmitter designed for portable device.

This is the initial version, any mistakes, please let me know, I will fix it in
the next series.

Thanks,
Xin


Xin Ji (2):
  dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver

 .../bindings/display/bridge/anx7625.yaml           |   96 +
 drivers/gpu/drm/bridge/Makefile                    |    2 +-
 drivers/gpu/drm/bridge/analogix/Kconfig            |    6 +
 drivers/gpu/drm/bridge/analogix/Makefile           |    1 +
 drivers/gpu/drm/bridge/analogix/anx7625.c          | 2155 ++++++++++++++++++++
 drivers/gpu/drm/bridge/analogix/anx7625.h          |  406 ++++
 6 files changed, 2665 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h

-- 
2.7.4

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

* [PATCH v2 0/2] Add initial support for slimport anx7625
@ 2019-10-09  9:26 Xin Ji
  0 siblings, 0 replies; 17+ messages in thread
From: Xin Ji @ 2019-10-09  9:26 UTC (permalink / raw)
  To: devel, Laurent Pinchart, Andrzej Hajda
  Cc: Jernej Skrabec, Nicolas Boichat, Jonas Karlman, David Airlie,
	Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
	Daniel Vetter, Dan Carpenter

Hi all,

The following series add initial support for the Slimport ANX7625 transmitter, a
ultra-low power Full-HD 4K MIPI to DP transmitter designed for portable device.

This is the initial version, any mistakes, please let me know, I will fix it in
the next series.

Thanks,
Xin


Xin Ji (2):
  dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding
  drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver

 .../bindings/display/bridge/anx7625.yaml           |   79 +
 drivers/gpu/drm/bridge/Makefile                    |    2 +-
 drivers/gpu/drm/bridge/analogix/Kconfig            |    6 +
 drivers/gpu/drm/bridge/analogix/Makefile           |    1 +
 drivers/gpu/drm/bridge/analogix/anx7625.c          | 2132 ++++++++++++++++++++
 drivers/gpu/drm/bridge/analogix/anx7625.h          |  405 ++++
 6 files changed, 2624 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/anx7625.yaml
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h

-- 
2.7.4

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

^ permalink raw reply	[flat|nested] 17+ messages in thread

end of thread, back to index

Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <CGME20191011022055epcas5p37790ed31cbe63d0be0f6b5786ce1392a@epcas5p3.samsung.com>
2019-10-11  2:20 ` [PATCH v2 0/2] Add initial support for slimport anx7625 Xin Ji
2019-10-11  2:21   ` [PATCH v2 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding Xin Ji
2019-10-11 11:21     ` Andrzej Hajda
2019-10-11 12:54       ` Laurent Pinchart
2019-10-14  3:02         ` Xin Ji
2019-10-14 22:16           ` Laurent Pinchart
2019-10-15  3:02             ` Xin Ji
2019-10-14  2:53       ` Xin Ji
2019-10-11  2:23   ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Xin Ji
2019-10-14  8:20     ` kbuild test robot
2019-10-14  8:20     ` [RFC PATCH] drm/bridge: anx7625: ANX_OUI[] can be static kbuild test robot
2019-10-15  9:19     ` [PATCH v2 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver Dan Carpenter
2019-10-11  6:12   ` [PATCH v2 0/2] Add initial support for slimport anx7625 Andrzej Hajda
2019-10-11  7:52     ` Xin Ji
2019-10-11 10:27   ` Dan Carpenter
2019-10-10  9:31 Xin Ji
  -- strict thread matches above, loose matches on Subject: below --
2019-10-09  9:26 Xin Ji

DriverDev-Devel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/driverdev-devel/0 driverdev-devel/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 driverdev-devel driverdev-devel/ https://lore.kernel.org/driverdev-devel \
		driverdev-devel@linuxdriverproject.org devel@driverdev.osuosl.org
	public-inbox-index driverdev-devel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.linuxdriverproject.driverdev-devel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git