* Re: [linux-sunxi] [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
2019-04-05 20:57 ` [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC Icenowy Zheng
@ 2019-04-06 17:21 ` Ondřej Jirman
2019-04-06 17:24 ` Icenowy Zheng
2019-04-09 16:34 ` Clément Péron
` (2 subsequent siblings)
3 siblings, 1 reply; 16+ messages in thread
From: Ondřej Jirman @ 2019-04-06 17:21 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Maxime Ripard, linux-sunxi, linux-kernel,
Kishon Vijay Abraham I, Chen-Yu Tsai, Rob Herring,
linux-arm-kernel
Hello Icenowy,
On Sat, Apr 06, 2019 at 04:57:34AM +0800, Icenowy Zheng wrote:
> Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
> controlled).
>
> Add a driver for it.
>
> The register operations in this driver is mainly extracted from the BSP
> USB3 driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes in v5:
> - Dropped support for vbus-supply property in the device node itself and
> added support for vbus-supply property in the connector subnode.
>
> Changes in v4:
> - Added support for vbus-supply property.
>
> Changes in v3:
> - Dropped USB_SUPPORT dependency.
> - Added Chen-Yu's Review tag.
>
> No changes in v2, v1. drivers/phy/allwinner/Kconfig | 12 ++
> drivers/phy/allwinner/Makefile | 1 +
> drivers/phy/allwinner/phy-sun50i-usb3.c | 260 ++++++++++++++++++++++++
> 3 files changed, 273 insertions(+)
> create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
>
> diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
> index fb1204bcc454..2c363db177f2 100644
> --- a/drivers/phy/allwinner/Kconfig
> +++ b/drivers/phy/allwinner/Kconfig
> @@ -41,3 +41,15 @@ config PHY_SUN9I_USB
> sun9i SoCs.
>
> This driver controls each individual USB 2 host PHY.
> +
> +config PHY_SUN50I_USB3
> + tristate "Allwinner sun50i SoC USB3 PHY driver"
> + depends on ARCH_SUNXI && HAS_IOMEM && OF
> + depends on RESET_CONTROLLER
> + select USB_COMMON
> + select GENERIC_PHY
> + help
> + Enable this to support the USB3.0-capable transceiver that is
> + part of some Allwinner sun50i SoCs.
> +
> + This driver controls each individual USB 2+3 host PHY combo.
> diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
> index 7d0053efbfaa..59575a895779 100644
> --- a/drivers/phy/allwinner/Makefile
> +++ b/drivers/phy/allwinner/Makefile
> @@ -1,3 +1,4 @@
> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY) += phy-sun6i-mipi-dphy.o
> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
> +obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o
> diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
> new file mode 100644
> index 000000000000..5299aef98668
> --- /dev/null
> +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Allwinner sun50i(H6) USB 3.0 phy driver
> + *
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on phy-sun9i-usb.c, which is:
> + *
> + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
> + *
> + * Based on code from Allwinner BSP, which is:
> + *
> + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/of_platform.h>
> +#include <linux/usb/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +
> +/* Interface Status and Control Registers */
> +#define SUNXI_ISCR 0x00
> +#define SUNXI_PIPE_CLOCK_CONTROL 0x14
> +#define SUNXI_PHY_TUNE_LOW 0x18
> +#define SUNXI_PHY_TUNE_HIGH 0x1c
> +#define SUNXI_PHY_EXTERNAL_CONTROL 0x20
> +
> +/* USB2.0 Interface Status and Control Register */
> +#define SUNXI_ISCR_FORCE_VBUS (3 << 12)
> +
> +/* PIPE Clock Control Register */
> +#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6)
> +
> +/* PHY External Control Register */
> +#define SUNXI_PEC_EXTERN_VBUS (3 << 1)
> +#define SUNXI_PEC_SSC_EN (1 << 24)
> +#define SUNXI_PEC_REF_SSP_EN (1 << 26)
> +
> +/* PHY Tune High Register */
> +#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19)
> +#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19)
> +#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13)
> +#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13)
> +#define SUNXI_TX_SWING_FULL(n) ((n) << 6)
> +#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6)
> +#define SUNXI_LOS_BIAS(n) ((n) << 3)
> +#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3)
> +#define SUNXI_TXVBOOSTLVL(n) ((n) << 0)
> +#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2)
> +
> +struct sun50i_usb3_phy {
> + struct phy *phy;
> + void __iomem *regs;
> + struct reset_control *reset;
> + struct clk *clk;
> + struct platform_device *connector_dev;
> + struct regulator *vbus;
> +};
> +
> +static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
> +{
> + u32 val;
> +
> + val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> + val |= SUNXI_PEC_EXTERN_VBUS;
> + val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
> + writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> + val |= SUNXI_PCC_PIPE_CLK_OPEN;
> + writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_ISCR);
> + val |= SUNXI_ISCR_FORCE_VBUS;
> + writel(val, phy->regs + SUNXI_ISCR);
> +
> + /*
> + * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
> + * registers are directly taken from the BSP USB3 driver from
> + * Allwiner.
> + */
> + writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
> +
> + val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
> + val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
> + SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
> + SUNXI_TX_DEEMPH_3P5DB_MASK);
> + val |= SUNXI_TXVBOOSTLVL(0x7);
> + val |= SUNXI_LOS_BIAS(0x7);
> + val |= SUNXI_TX_SWING_FULL(0x55);
> + val |= SUNXI_TX_DEEMPH_6DB(0x20);
> + val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
> + writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
> +}
> +
> +static int sun50i_usb3_phy_init(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> + int ret;
> +
> + ret = clk_prepare_enable(phy->clk);
> + if (ret)
> + goto err_clk;
> +
> + ret = reset_control_deassert(phy->reset);
> + if (ret)
> + goto err_reset;
> +
> + sun50i_usb3_phy_open(phy);
> + return 0;
> +
> +err_reset:
> + clk_disable_unprepare(phy->clk);
> +
> +err_clk:
> + return ret;
> +}
> +
> +static int sun50i_usb3_phy_exit(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + reset_control_assert(phy->reset);
> + clk_disable_unprepare(phy->clk);
> +
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_on(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_enable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_off(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_disable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static const struct phy_ops sun50i_usb3_phy_ops = {
> + .init = sun50i_usb3_phy_init,
> + .exit = sun50i_usb3_phy_exit,
> + .power_on = sun50i_usb3_phy_power_on,
> + .power_off = sun50i_usb3_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int sun50i_usb3_phy_probe(struct platform_device *pdev)
> +{
> + struct sun50i_usb3_phy *phy;
> + struct device *dev = &pdev->dev;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct device_node *connector_node;
> + int ret;
> +
> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> + if (!phy)
> + return -ENOMEM;
> +
> + dev_set_drvdata(dev, phy);
> +
> + phy->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(phy->clk)) {
> + dev_err(dev, "failed to get phy clock\n");
> + return PTR_ERR(phy->clk);
> + }
> +
> + phy->reset = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(phy->reset)) {
> + dev_err(dev, "failed to get reset control\n");
> + return PTR_ERR(phy->reset);
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + phy->regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(phy->regs))
> + return PTR_ERR(phy->regs);
> +
> + /* Populate the connector as platform device */
> + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
> + if (ret)
> + return ret;
> +
> + /*
> + * Currently the Allwinner USB3 PHY contains only one port, so we
> + * only process one connector now.
> + */
> + connector_node = of_get_next_child(pdev->dev.of_node, NULL);
> +
> + if (connector_node) {
> + /* Get the platform device */
> + phy->connector_dev = of_find_device_by_node(connector_node);
> + if (!phy->connector_dev) {
> + dev_err(dev, "no device for connector\n");
> + return -ENODEV;
> + }
> +
> + phy->vbus = regulator_get(&phy->connector_dev->dev, "vbus");
> + if (IS_ERR(phy->vbus))
> + return PTR_ERR(phy->vbus);
> + }
> +
> + phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
> + if (IS_ERR(phy->phy)) {
You're possibly leaking phy->vbus here.
> + dev_err(dev, "failed to create PHY\n");
> + return PTR_ERR(phy->phy);
> + }
> +
> + phy_set_drvdata(phy->phy, phy);
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
... and also here:
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int sun50i_usb3_phy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct sun50i_usb3_phy *phy = dev_get_drvdata(dev);
> +
> + if (phy->vbus)
> + regulator_put(phy->vbus);
Perhaps just use devm_regulator_get, and drop he sun50i_usb3_phy_remove
entirely?
thank you and regards,
Ondrej
> + return 0;
> +}
> +
> +static const struct of_device_id sun50i_usb3_phy_of_match[] = {
> + { .compatible = "allwinner,sun50i-h6-usb3-phy" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
> +
> +static struct platform_driver sun50i_usb3_phy_driver = {
> + .probe = sun50i_usb3_phy_probe,
> + .remove = sun50i_usb3_phy_remove,
> + .driver = {
> + .of_match_table = sun50i_usb3_phy_of_match,
> + .name = "sun50i-usb3-phy",
> + }
> +};
> +module_platform_driver(sun50i_usb3_phy_driver);
> +
> +MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [linux-sunxi] [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
2019-04-06 17:21 ` [linux-sunxi] " Ondřej Jirman
@ 2019-04-06 17:24 ` Icenowy Zheng
0 siblings, 0 replies; 16+ messages in thread
From: Icenowy Zheng @ 2019-04-06 17:24 UTC (permalink / raw)
To: Ondřej Jirman
Cc: devicetree, Maxime Ripard, linux-sunxi, linux-kernel,
Kishon Vijay Abraham I, Chen-Yu Tsai, Rob Herring,
linux-arm-kernel
于 2019年4月7日 GMT+08:00 上午1:21:13, "Ondřej Jirman" <megous@megous.com> 写到:
>Hello Icenowy,
>
>On Sat, Apr 06, 2019 at 04:57:34AM +0800, Icenowy Zheng wrote:
>> Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
>> controlled).
>>
>> Add a driver for it.
>>
>> The register operations in this driver is mainly extracted from the
>BSP
>> USB3 driver.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
>> ---
>> Changes in v5:
>> - Dropped support for vbus-supply property in the device node itself
>and
>> added support for vbus-supply property in the connector subnode.
>>
>> Changes in v4:
>> - Added support for vbus-supply property.
>>
>> Changes in v3:
>> - Dropped USB_SUPPORT dependency.
>> - Added Chen-Yu's Review tag.
>>
>> No changes in v2, v1. drivers/phy/allwinner/Kconfig | 12
>++
>> drivers/phy/allwinner/Makefile | 1 +
>> drivers/phy/allwinner/phy-sun50i-usb3.c | 260
>++++++++++++++++++++++++
>> 3 files changed, 273 insertions(+)
>> create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
>>
>> diff --git a/drivers/phy/allwinner/Kconfig
>b/drivers/phy/allwinner/Kconfig
>> index fb1204bcc454..2c363db177f2 100644
>> --- a/drivers/phy/allwinner/Kconfig
>> +++ b/drivers/phy/allwinner/Kconfig
>> @@ -41,3 +41,15 @@ config PHY_SUN9I_USB
>> sun9i SoCs.
>>
>> This driver controls each individual USB 2 host PHY.
>> +
>> +config PHY_SUN50I_USB3
>> + tristate "Allwinner sun50i SoC USB3 PHY driver"
>> + depends on ARCH_SUNXI && HAS_IOMEM && OF
>> + depends on RESET_CONTROLLER
>> + select USB_COMMON
>> + select GENERIC_PHY
>> + help
>> + Enable this to support the USB3.0-capable transceiver that is
>> + part of some Allwinner sun50i SoCs.
>> +
>> + This driver controls each individual USB 2+3 host PHY combo.
>> diff --git a/drivers/phy/allwinner/Makefile
>b/drivers/phy/allwinner/Makefile
>> index 7d0053efbfaa..59575a895779 100644
>> --- a/drivers/phy/allwinner/Makefile
>> +++ b/drivers/phy/allwinner/Makefile
>> @@ -1,3 +1,4 @@
>> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
>> obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY) += phy-sun6i-mipi-dphy.o
>> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
>> +obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o
>> diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c
>b/drivers/phy/allwinner/phy-sun50i-usb3.c
>> new file mode 100644
>> index 000000000000..5299aef98668
>> --- /dev/null
>> +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
>> @@ -0,0 +1,260 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Allwinner sun50i(H6) USB 3.0 phy driver
>> + *
>> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> + *
>> + * Based on phy-sun9i-usb.c, which is:
>> + *
>> + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
>> + *
>> + * Based on code from Allwinner BSP, which is:
>> + *
>> + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/err.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/usb/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <linux/reset.h>
>> +
>> +/* Interface Status and Control Registers */
>> +#define SUNXI_ISCR 0x00
>> +#define SUNXI_PIPE_CLOCK_CONTROL 0x14
>> +#define SUNXI_PHY_TUNE_LOW 0x18
>> +#define SUNXI_PHY_TUNE_HIGH 0x1c
>> +#define SUNXI_PHY_EXTERNAL_CONTROL 0x20
>> +
>> +/* USB2.0 Interface Status and Control Register */
>> +#define SUNXI_ISCR_FORCE_VBUS (3 << 12)
>> +
>> +/* PIPE Clock Control Register */
>> +#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6)
>> +
>> +/* PHY External Control Register */
>> +#define SUNXI_PEC_EXTERN_VBUS (3 << 1)
>> +#define SUNXI_PEC_SSC_EN (1 << 24)
>> +#define SUNXI_PEC_REF_SSP_EN (1 << 26)
>> +
>> +/* PHY Tune High Register */
>> +#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19)
>> +#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19)
>> +#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13)
>> +#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13)
>> +#define SUNXI_TX_SWING_FULL(n) ((n) << 6)
>> +#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6)
>> +#define SUNXI_LOS_BIAS(n) ((n) << 3)
>> +#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3)
>> +#define SUNXI_TXVBOOSTLVL(n) ((n) << 0)
>> +#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2)
>> +
>> +struct sun50i_usb3_phy {
>> + struct phy *phy;
>> + void __iomem *regs;
>> + struct reset_control *reset;
>> + struct clk *clk;
>> + struct platform_device *connector_dev;
>> + struct regulator *vbus;
>> +};
>> +
>> +static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
>> +{
>> + u32 val;
>> +
>> + val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
>> + val |= SUNXI_PEC_EXTERN_VBUS;
>> + val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
>> + writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
>> +
>> + val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
>> + val |= SUNXI_PCC_PIPE_CLK_OPEN;
>> + writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
>> +
>> + val = readl(phy->regs + SUNXI_ISCR);
>> + val |= SUNXI_ISCR_FORCE_VBUS;
>> + writel(val, phy->regs + SUNXI_ISCR);
>> +
>> + /*
>> + * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
>> + * registers are directly taken from the BSP USB3 driver from
>> + * Allwiner.
>> + */
>> + writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
>> +
>> + val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
>> + val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
>> + SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
>> + SUNXI_TX_DEEMPH_3P5DB_MASK);
>> + val |= SUNXI_TXVBOOSTLVL(0x7);
>> + val |= SUNXI_LOS_BIAS(0x7);
>> + val |= SUNXI_TX_SWING_FULL(0x55);
>> + val |= SUNXI_TX_DEEMPH_6DB(0x20);
>> + val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
>> + writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
>> +}
>> +
>> +static int sun50i_usb3_phy_init(struct phy *_phy)
>> +{
>> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
>> + int ret;
>> +
>> + ret = clk_prepare_enable(phy->clk);
>> + if (ret)
>> + goto err_clk;
>> +
>> + ret = reset_control_deassert(phy->reset);
>> + if (ret)
>> + goto err_reset;
>> +
>> + sun50i_usb3_phy_open(phy);
>> + return 0;
>> +
>> +err_reset:
>> + clk_disable_unprepare(phy->clk);
>> +
>> +err_clk:
>> + return ret;
>> +}
>> +
>> +static int sun50i_usb3_phy_exit(struct phy *_phy)
>> +{
>> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
>> +
>> + reset_control_assert(phy->reset);
>> + clk_disable_unprepare(phy->clk);
>> +
>> + return 0;
>> +}
>> +
>> +static int sun50i_usb3_phy_power_on(struct phy *_phy)
>> +{
>> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
>> +
>> + if (phy->vbus)
>> + return regulator_enable(phy->vbus);
>> + else
>> + return 0;
>> +}
>> +
>> +static int sun50i_usb3_phy_power_off(struct phy *_phy)
>> +{
>> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
>> +
>> + if (phy->vbus)
>> + return regulator_disable(phy->vbus);
>> + else
>> + return 0;
>> +}
>> +
>> +static const struct phy_ops sun50i_usb3_phy_ops = {
>> + .init = sun50i_usb3_phy_init,
>> + .exit = sun50i_usb3_phy_exit,
>> + .power_on = sun50i_usb3_phy_power_on,
>> + .power_off = sun50i_usb3_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int sun50i_usb3_phy_probe(struct platform_device *pdev)
>> +{
>> + struct sun50i_usb3_phy *phy;
>> + struct device *dev = &pdev->dev;
>> + struct phy_provider *phy_provider;
>> + struct resource *res;
>> + struct device_node *connector_node;
>> + int ret;
>> +
>> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
>> + if (!phy)
>> + return -ENOMEM;
>> +
>> + dev_set_drvdata(dev, phy);
>> +
>> + phy->clk = devm_clk_get(dev, NULL);
>> + if (IS_ERR(phy->clk)) {
>> + dev_err(dev, "failed to get phy clock\n");
>> + return PTR_ERR(phy->clk);
>> + }
>> +
>> + phy->reset = devm_reset_control_get(dev, NULL);
>> + if (IS_ERR(phy->reset)) {
>> + dev_err(dev, "failed to get reset control\n");
>> + return PTR_ERR(phy->reset);
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + phy->regs = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(phy->regs))
>> + return PTR_ERR(phy->regs);
>> +
>> + /* Populate the connector as platform device */
>> + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL,
>&pdev->dev);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * Currently the Allwinner USB3 PHY contains only one port, so we
>> + * only process one connector now.
>> + */
>> + connector_node = of_get_next_child(pdev->dev.of_node, NULL);
>> +
>> + if (connector_node) {
>> + /* Get the platform device */
>> + phy->connector_dev = of_find_device_by_node(connector_node);
>> + if (!phy->connector_dev) {
>> + dev_err(dev, "no device for connector\n");
>> + return -ENODEV;
>> + }
>> +
>> + phy->vbus = regulator_get(&phy->connector_dev->dev, "vbus");
>> + if (IS_ERR(phy->vbus))
>> + return PTR_ERR(phy->vbus);
>> + }
>> +
>> + phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
>> + if (IS_ERR(phy->phy)) {
>
>You're possibly leaking phy->vbus here.
Thanks.
>
>> + dev_err(dev, "failed to create PHY\n");
>> + return PTR_ERR(phy->phy);
>> + }
>> +
>> + phy_set_drvdata(phy->phy, phy);
>> + phy_provider = devm_of_phy_provider_register(dev,
>of_phy_simple_xlate);
>> +
>
>... and also here:
>
>> + return PTR_ERR_OR_ZERO(phy_provider);
>> +}
>> +
>> +static int sun50i_usb3_phy_remove(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct sun50i_usb3_phy *phy = dev_get_drvdata(dev);
>> +
>> + if (phy->vbus)
>> + regulator_put(phy->vbus);
>
>Perhaps just use devm_regulator_get, and drop he sun50i_usb3_phy_remove
>entirely?
No. We're borrowing another device's regulator, so devm function won't
work here -- it will clean up when the connector gets removed, not the phy,
but the connector has no driver.
>
>thank you and regards,
> Ondrej
>
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id sun50i_usb3_phy_of_match[] = {
>> + { .compatible = "allwinner,sun50i-h6-usb3-phy" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
>> +
>> +static struct platform_driver sun50i_usb3_phy_driver = {
>> + .probe = sun50i_usb3_phy_probe,
>> + .remove = sun50i_usb3_phy_remove,
>> + .driver = {
>> + .of_match_table = sun50i_usb3_phy_of_match,
>> + .name = "sun50i-usb3-phy",
>> + }
>> +};
>> +module_platform_driver(sun50i_usb3_phy_driver);
>> +
>> +MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
>> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
>> +MODULE_LICENSE("GPL");
>> --
>> 2.18.1
>>
>> --
>> You received this message because you are subscribed to the Google
>Groups "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it,
>send an email to linux-sunxi+unsubscribe@googlegroups.com.
>> For more options, visit https://groups.google.com/d/optout.
--
使用 K-9 Mail 发送自我的Android设备。
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [linux-sunxi] [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
2019-04-05 20:57 ` [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC Icenowy Zheng
2019-04-06 17:21 ` [linux-sunxi] " Ondřej Jirman
@ 2019-04-09 16:34 ` Clément Péron
2019-04-11 0:15 ` Ondřej Jirman
2019-04-11 0:20 ` Ondřej Jirman
3 siblings, 0 replies; 16+ messages in thread
From: Clément Péron @ 2019-04-09 16:34 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Maxime Ripard, linux-sunxi, linux-kernel,
Kishon Vijay Abraham I, Chen-Yu Tsai, Rob Herring,
linux-arm-kernel
Hi,
On Fri, 5 Apr 2019 at 22:58, Icenowy Zheng <icenowy@aosc.io> wrote:
>
> Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
> controlled).
>
> Add a driver for it.
Tested the serie on top of sunxi/for-next with USB3 storage and
HID-generic keyboard on my Beelink GS1.
Tested-by: Clément Péron <peron.clem@gmail.com>
Just a suggestion could you add a patch to enable this PHY in the
arm64/defconfig by default ?
Thanks,
Clément
>
> The register operations in this driver is mainly extracted from the BSP
> USB3 driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes in v5:
> - Dropped support for vbus-supply property in the device node itself and
> added support for vbus-supply property in the connector subnode.
>
> Changes in v4:
> - Added support for vbus-supply property.
>
> Changes in v3:
> - Dropped USB_SUPPORT dependency.
> - Added Chen-Yu's Review tag.
>
> No changes in v2, v1. drivers/phy/allwinner/Kconfig | 12 ++
> drivers/phy/allwinner/Makefile | 1 +
> drivers/phy/allwinner/phy-sun50i-usb3.c | 260 ++++++++++++++++++++++++
> 3 files changed, 273 insertions(+)
> create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
>
> diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
> index fb1204bcc454..2c363db177f2 100644
> --- a/drivers/phy/allwinner/Kconfig
> +++ b/drivers/phy/allwinner/Kconfig
> @@ -41,3 +41,15 @@ config PHY_SUN9I_USB
> sun9i SoCs.
>
> This driver controls each individual USB 2 host PHY.
> +
> +config PHY_SUN50I_USB3
> + tristate "Allwinner sun50i SoC USB3 PHY driver"
> + depends on ARCH_SUNXI && HAS_IOMEM && OF
> + depends on RESET_CONTROLLER
> + select USB_COMMON
> + select GENERIC_PHY
> + help
> + Enable this to support the USB3.0-capable transceiver that is
> + part of some Allwinner sun50i SoCs.
> +
> + This driver controls each individual USB 2+3 host PHY combo.
> diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
> index 7d0053efbfaa..59575a895779 100644
> --- a/drivers/phy/allwinner/Makefile
> +++ b/drivers/phy/allwinner/Makefile
> @@ -1,3 +1,4 @@
> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY) += phy-sun6i-mipi-dphy.o
> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
> +obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o
> diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
> new file mode 100644
> index 000000000000..5299aef98668
> --- /dev/null
> +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Allwinner sun50i(H6) USB 3.0 phy driver
> + *
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on phy-sun9i-usb.c, which is:
> + *
> + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
> + *
> + * Based on code from Allwinner BSP, which is:
> + *
> + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/of_platform.h>
> +#include <linux/usb/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +
> +/* Interface Status and Control Registers */
> +#define SUNXI_ISCR 0x00
> +#define SUNXI_PIPE_CLOCK_CONTROL 0x14
> +#define SUNXI_PHY_TUNE_LOW 0x18
> +#define SUNXI_PHY_TUNE_HIGH 0x1c
> +#define SUNXI_PHY_EXTERNAL_CONTROL 0x20
> +
> +/* USB2.0 Interface Status and Control Register */
> +#define SUNXI_ISCR_FORCE_VBUS (3 << 12)
> +
> +/* PIPE Clock Control Register */
> +#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6)
> +
> +/* PHY External Control Register */
> +#define SUNXI_PEC_EXTERN_VBUS (3 << 1)
> +#define SUNXI_PEC_SSC_EN (1 << 24)
> +#define SUNXI_PEC_REF_SSP_EN (1 << 26)
> +
> +/* PHY Tune High Register */
> +#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19)
> +#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19)
> +#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13)
> +#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13)
> +#define SUNXI_TX_SWING_FULL(n) ((n) << 6)
> +#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6)
> +#define SUNXI_LOS_BIAS(n) ((n) << 3)
> +#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3)
> +#define SUNXI_TXVBOOSTLVL(n) ((n) << 0)
> +#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2)
> +
> +struct sun50i_usb3_phy {
> + struct phy *phy;
> + void __iomem *regs;
> + struct reset_control *reset;
> + struct clk *clk;
> + struct platform_device *connector_dev;
> + struct regulator *vbus;
> +};
> +
> +static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
> +{
> + u32 val;
> +
> + val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> + val |= SUNXI_PEC_EXTERN_VBUS;
> + val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
> + writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> + val |= SUNXI_PCC_PIPE_CLK_OPEN;
> + writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_ISCR);
> + val |= SUNXI_ISCR_FORCE_VBUS;
> + writel(val, phy->regs + SUNXI_ISCR);
> +
> + /*
> + * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
> + * registers are directly taken from the BSP USB3 driver from
> + * Allwiner.
> + */
> + writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
> +
> + val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
> + val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
> + SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
> + SUNXI_TX_DEEMPH_3P5DB_MASK);
> + val |= SUNXI_TXVBOOSTLVL(0x7);
> + val |= SUNXI_LOS_BIAS(0x7);
> + val |= SUNXI_TX_SWING_FULL(0x55);
> + val |= SUNXI_TX_DEEMPH_6DB(0x20);
> + val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
> + writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
> +}
> +
> +static int sun50i_usb3_phy_init(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> + int ret;
> +
> + ret = clk_prepare_enable(phy->clk);
> + if (ret)
> + goto err_clk;
> +
> + ret = reset_control_deassert(phy->reset);
> + if (ret)
> + goto err_reset;
> +
> + sun50i_usb3_phy_open(phy);
> + return 0;
> +
> +err_reset:
> + clk_disable_unprepare(phy->clk);
> +
> +err_clk:
> + return ret;
> +}
> +
> +static int sun50i_usb3_phy_exit(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + reset_control_assert(phy->reset);
> + clk_disable_unprepare(phy->clk);
> +
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_on(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_enable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_off(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_disable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static const struct phy_ops sun50i_usb3_phy_ops = {
> + .init = sun50i_usb3_phy_init,
> + .exit = sun50i_usb3_phy_exit,
> + .power_on = sun50i_usb3_phy_power_on,
> + .power_off = sun50i_usb3_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int sun50i_usb3_phy_probe(struct platform_device *pdev)
> +{
> + struct sun50i_usb3_phy *phy;
> + struct device *dev = &pdev->dev;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct device_node *connector_node;
> + int ret;
> +
> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> + if (!phy)
> + return -ENOMEM;
> +
> + dev_set_drvdata(dev, phy);
> +
> + phy->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(phy->clk)) {
> + dev_err(dev, "failed to get phy clock\n");
> + return PTR_ERR(phy->clk);
> + }
> +
> + phy->reset = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(phy->reset)) {
> + dev_err(dev, "failed to get reset control\n");
> + return PTR_ERR(phy->reset);
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + phy->regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(phy->regs))
> + return PTR_ERR(phy->regs);
> +
> + /* Populate the connector as platform device */
> + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
> + if (ret)
> + return ret;
> +
> + /*
> + * Currently the Allwinner USB3 PHY contains only one port, so we
> + * only process one connector now.
> + */
> + connector_node = of_get_next_child(pdev->dev.of_node, NULL);
> +
> + if (connector_node) {
> + /* Get the platform device */
> + phy->connector_dev = of_find_device_by_node(connector_node);
> + if (!phy->connector_dev) {
> + dev_err(dev, "no device for connector\n");
> + return -ENODEV;
> + }
> +
> + phy->vbus = regulator_get(&phy->connector_dev->dev, "vbus");
> + if (IS_ERR(phy->vbus))
> + return PTR_ERR(phy->vbus);
> + }
> +
> + phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
> + if (IS_ERR(phy->phy)) {
> + dev_err(dev, "failed to create PHY\n");
> + return PTR_ERR(phy->phy);
> + }
> +
> + phy_set_drvdata(phy->phy, phy);
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int sun50i_usb3_phy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct sun50i_usb3_phy *phy = dev_get_drvdata(dev);
> +
> + if (phy->vbus)
> + regulator_put(phy->vbus);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id sun50i_usb3_phy_of_match[] = {
> + { .compatible = "allwinner,sun50i-h6-usb3-phy" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
> +
> +static struct platform_driver sun50i_usb3_phy_driver = {
> + .probe = sun50i_usb3_phy_probe,
> + .remove = sun50i_usb3_phy_remove,
> + .driver = {
> + .of_match_table = sun50i_usb3_phy_of_match,
> + .name = "sun50i-usb3-phy",
> + }
> +};
> +module_platform_driver(sun50i_usb3_phy_driver);
> +
> +MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [linux-sunxi] [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
2019-04-05 20:57 ` [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC Icenowy Zheng
2019-04-06 17:21 ` [linux-sunxi] " Ondřej Jirman
2019-04-09 16:34 ` Clément Péron
@ 2019-04-11 0:15 ` Ondřej Jirman
2019-04-11 0:20 ` Ondřej Jirman
3 siblings, 0 replies; 16+ messages in thread
From: Ondřej Jirman @ 2019-04-11 0:15 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Maxime Ripard, linux-sunxi, linux-kernel,
Kishon Vijay Abraham I, Chen-Yu Tsai, Rob Herring,
linux-arm-kernel
Hello Icenowy,
On Sat, Apr 06, 2019 at 04:57:34AM +0800, Icenowy Zheng wrote:
> Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
> controlled).
>
> Add a driver for it.
>
> The register operations in this driver is mainly extracted from the BSP
> USB3 driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes in v5:
> - Dropped support for vbus-supply property in the device node itself and
> added support for vbus-supply property in the connector subnode.
>
> Changes in v4:
> - Added support for vbus-supply property.
>
> Changes in v3:
> - Dropped USB_SUPPORT dependency.
> - Added Chen-Yu's Review tag.
>
> No changes in v2, v1. drivers/phy/allwinner/Kconfig | 12 ++
> drivers/phy/allwinner/Makefile | 1 +
> drivers/phy/allwinner/phy-sun50i-usb3.c | 260 ++++++++++++++++++++++++
> 3 files changed, 273 insertions(+)
> create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
>
> diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
> index fb1204bcc454..2c363db177f2 100644
> --- a/drivers/phy/allwinner/Kconfig
> +++ b/drivers/phy/allwinner/Kconfig
> @@ -41,3 +41,15 @@ config PHY_SUN9I_USB
> sun9i SoCs.
>
> This driver controls each individual USB 2 host PHY.
> +
> +config PHY_SUN50I_USB3
> + tristate "Allwinner sun50i SoC USB3 PHY driver"
> + depends on ARCH_SUNXI && HAS_IOMEM && OF
> + depends on RESET_CONTROLLER
> + select USB_COMMON
> + select GENERIC_PHY
> + help
> + Enable this to support the USB3.0-capable transceiver that is
> + part of some Allwinner sun50i SoCs.
> +
> + This driver controls each individual USB 2+3 host PHY combo.
> diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
> index 7d0053efbfaa..59575a895779 100644
> --- a/drivers/phy/allwinner/Makefile
> +++ b/drivers/phy/allwinner/Makefile
> @@ -1,3 +1,4 @@
> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY) += phy-sun6i-mipi-dphy.o
> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
> +obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o
> diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
> new file mode 100644
> index 000000000000..5299aef98668
> --- /dev/null
> +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Allwinner sun50i(H6) USB 3.0 phy driver
> + *
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on phy-sun9i-usb.c, which is:
> + *
> + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
> + *
> + * Based on code from Allwinner BSP, which is:
> + *
> + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/of_platform.h>
> +#include <linux/usb/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +
> +/* Interface Status and Control Registers */
> +#define SUNXI_ISCR 0x00
> +#define SUNXI_PIPE_CLOCK_CONTROL 0x14
> +#define SUNXI_PHY_TUNE_LOW 0x18
> +#define SUNXI_PHY_TUNE_HIGH 0x1c
> +#define SUNXI_PHY_EXTERNAL_CONTROL 0x20
> +
> +/* USB2.0 Interface Status and Control Register */
> +#define SUNXI_ISCR_FORCE_VBUS (3 << 12)
> +
> +/* PIPE Clock Control Register */
> +#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6)
> +
> +/* PHY External Control Register */
> +#define SUNXI_PEC_EXTERN_VBUS (3 << 1)
> +#define SUNXI_PEC_SSC_EN (1 << 24)
> +#define SUNXI_PEC_REF_SSP_EN (1 << 26)
> +
> +/* PHY Tune High Register */
> +#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19)
> +#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19)
> +#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13)
> +#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13)
> +#define SUNXI_TX_SWING_FULL(n) ((n) << 6)
> +#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6)
> +#define SUNXI_LOS_BIAS(n) ((n) << 3)
> +#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3)
> +#define SUNXI_TXVBOOSTLVL(n) ((n) << 0)
> +#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2)
> +
> +struct sun50i_usb3_phy {
> + struct phy *phy;
> + void __iomem *regs;
> + struct reset_control *reset;
> + struct clk *clk;
> + struct platform_device *connector_dev;
> + struct regulator *vbus;
> +};
> +
> +static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
> +{
> + u32 val;
> +
> + val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> + val |= SUNXI_PEC_EXTERN_VBUS;
> + val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
> + writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> + val |= SUNXI_PCC_PIPE_CLK_OPEN;
> + writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_ISCR);
> + val |= SUNXI_ISCR_FORCE_VBUS;
> + writel(val, phy->regs + SUNXI_ISCR);
> +
> + /*
> + * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
> + * registers are directly taken from the BSP USB3 driver from
> + * Allwiner.
> + */
> + writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
> +
> + val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
> + val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
> + SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
> + SUNXI_TX_DEEMPH_3P5DB_MASK);
> + val |= SUNXI_TXVBOOSTLVL(0x7);
> + val |= SUNXI_LOS_BIAS(0x7);
> + val |= SUNXI_TX_SWING_FULL(0x55);
> + val |= SUNXI_TX_DEEMPH_6DB(0x20);
> + val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
> + writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
> +}
> +
> +static int sun50i_usb3_phy_init(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> + int ret;
> +
> + ret = clk_prepare_enable(phy->clk);
> + if (ret)
> + goto err_clk;
> +
> + ret = reset_control_deassert(phy->reset);
> + if (ret)
> + goto err_reset;
> +
> + sun50i_usb3_phy_open(phy);
> + return 0;
> +
> +err_reset:
> + clk_disable_unprepare(phy->clk);
> +
> +err_clk:
> + return ret;
> +}
> +
> +static int sun50i_usb3_phy_exit(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + reset_control_assert(phy->reset);
> + clk_disable_unprepare(phy->clk);
> +
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_on(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_enable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_off(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_disable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static const struct phy_ops sun50i_usb3_phy_ops = {
> + .init = sun50i_usb3_phy_init,
> + .exit = sun50i_usb3_phy_exit,
> + .power_on = sun50i_usb3_phy_power_on,
> + .power_off = sun50i_usb3_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int sun50i_usb3_phy_probe(struct platform_device *pdev)
> +{
> + struct sun50i_usb3_phy *phy;
> + struct device *dev = &pdev->dev;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct device_node *connector_node;
> + int ret;
> +
> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> + if (!phy)
> + return -ENOMEM;
> +
> + dev_set_drvdata(dev, phy);
> +
> + phy->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(phy->clk)) {
> + dev_err(dev, "failed to get phy clock\n");
> + return PTR_ERR(phy->clk);
> + }
> +
> + phy->reset = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(phy->reset)) {
> + dev_err(dev, "failed to get reset control\n");
> + return PTR_ERR(phy->reset);
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + phy->regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(phy->regs))
> + return PTR_ERR(phy->regs);
> +
> + /* Populate the connector as platform device */
> + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
> + if (ret)
> + return ret;
> +
> + /*
> + * Currently the Allwinner USB3 PHY contains only one port, so we
> + * only process one connector now.
> + */
> + connector_node = of_get_next_child(pdev->dev.of_node, NULL);
I also noticed, that you're leaking connector_node, but I guess next patch will
not have this code, so anyway... You should call of_node_put(). So just
something to keep in mind in the future.
regards,
o.
> + if (connector_node) {
> + /* Get the platform device */
> + phy->connector_dev = of_find_device_by_node(connector_node);
> + if (!phy->connector_dev) {
> + dev_err(dev, "no device for connector\n");
> + return -ENODEV;
> + }
> +
> + phy->vbus = regulator_get(&phy->connector_dev->dev, "vbus");
> + if (IS_ERR(phy->vbus))
> + return PTR_ERR(phy->vbus);
> + }
> +
> + phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
> + if (IS_ERR(phy->phy)) {
> + dev_err(dev, "failed to create PHY\n");
> + return PTR_ERR(phy->phy);
> + }
> +
> + phy_set_drvdata(phy->phy, phy);
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int sun50i_usb3_phy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct sun50i_usb3_phy *phy = dev_get_drvdata(dev);
> +
> + if (phy->vbus)
> + regulator_put(phy->vbus);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id sun50i_usb3_phy_of_match[] = {
> + { .compatible = "allwinner,sun50i-h6-usb3-phy" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
> +
> +static struct platform_driver sun50i_usb3_phy_driver = {
> + .probe = sun50i_usb3_phy_probe,
> + .remove = sun50i_usb3_phy_remove,
> + .driver = {
> + .of_match_table = sun50i_usb3_phy_of_match,
> + .name = "sun50i-usb3-phy",
> + }
> +};
> +module_platform_driver(sun50i_usb3_phy_driver);
> +
> +MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [linux-sunxi] [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
2019-04-05 20:57 ` [PATCH v5 3/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC Icenowy Zheng
` (2 preceding siblings ...)
2019-04-11 0:15 ` Ondřej Jirman
@ 2019-04-11 0:20 ` Ondřej Jirman
3 siblings, 0 replies; 16+ messages in thread
From: Ondřej Jirman @ 2019-04-11 0:20 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Maxime Ripard, linux-sunxi, linux-kernel,
Kishon Vijay Abraham I, Chen-Yu Tsai, Rob Herring,
linux-arm-kernel
On Sat, Apr 06, 2019 at 04:57:34AM +0800, Icenowy Zheng wrote:
> Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
> controlled).
>
> Add a driver for it.
>
> The register operations in this driver is mainly extracted from the BSP
> USB3 driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes in v5:
> - Dropped support for vbus-supply property in the device node itself and
> added support for vbus-supply property in the connector subnode.
>
> Changes in v4:
> - Added support for vbus-supply property.
>
> Changes in v3:
> - Dropped USB_SUPPORT dependency.
> - Added Chen-Yu's Review tag.
>
> No changes in v2, v1. drivers/phy/allwinner/Kconfig | 12 ++
> drivers/phy/allwinner/Makefile | 1 +
> drivers/phy/allwinner/phy-sun50i-usb3.c | 260 ++++++++++++++++++++++++
> 3 files changed, 273 insertions(+)
> create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
>
> diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
> index fb1204bcc454..2c363db177f2 100644
> --- a/drivers/phy/allwinner/Kconfig
> +++ b/drivers/phy/allwinner/Kconfig
> @@ -41,3 +41,15 @@ config PHY_SUN9I_USB
> sun9i SoCs.
>
> This driver controls each individual USB 2 host PHY.
> +
> +config PHY_SUN50I_USB3
> + tristate "Allwinner sun50i SoC USB3 PHY driver"
> + depends on ARCH_SUNXI && HAS_IOMEM && OF
> + depends on RESET_CONTROLLER
> + select USB_COMMON
> + select GENERIC_PHY
> + help
> + Enable this to support the USB3.0-capable transceiver that is
> + part of some Allwinner sun50i SoCs.
> +
> + This driver controls each individual USB 2+3 host PHY combo.
> diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
> index 7d0053efbfaa..59575a895779 100644
> --- a/drivers/phy/allwinner/Makefile
> +++ b/drivers/phy/allwinner/Makefile
> @@ -1,3 +1,4 @@
> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY) += phy-sun6i-mipi-dphy.o
> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
> +obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o
> diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
> new file mode 100644
> index 000000000000..5299aef98668
> --- /dev/null
> +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
> @@ -0,0 +1,260 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Allwinner sun50i(H6) USB 3.0 phy driver
> + *
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on phy-sun9i-usb.c, which is:
> + *
> + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
> + *
> + * Based on code from Allwinner BSP, which is:
> + *
> + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/of_platform.h>
> +#include <linux/usb/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +
> +/* Interface Status and Control Registers */
> +#define SUNXI_ISCR 0x00
> +#define SUNXI_PIPE_CLOCK_CONTROL 0x14
> +#define SUNXI_PHY_TUNE_LOW 0x18
> +#define SUNXI_PHY_TUNE_HIGH 0x1c
> +#define SUNXI_PHY_EXTERNAL_CONTROL 0x20
> +
> +/* USB2.0 Interface Status and Control Register */
> +#define SUNXI_ISCR_FORCE_VBUS (3 << 12)
> +
> +/* PIPE Clock Control Register */
> +#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6)
> +
> +/* PHY External Control Register */
> +#define SUNXI_PEC_EXTERN_VBUS (3 << 1)
> +#define SUNXI_PEC_SSC_EN (1 << 24)
> +#define SUNXI_PEC_REF_SSP_EN (1 << 26)
> +
> +/* PHY Tune High Register */
> +#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19)
> +#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19)
> +#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13)
> +#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13)
> +#define SUNXI_TX_SWING_FULL(n) ((n) << 6)
> +#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6)
> +#define SUNXI_LOS_BIAS(n) ((n) << 3)
> +#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3)
> +#define SUNXI_TXVBOOSTLVL(n) ((n) << 0)
> +#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2)
> +
> +struct sun50i_usb3_phy {
> + struct phy *phy;
> + void __iomem *regs;
> + struct reset_control *reset;
> + struct clk *clk;
> + struct platform_device *connector_dev;
> + struct regulator *vbus;
> +};
> +
> +static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
> +{
> + u32 val;
> +
> + val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> + val |= SUNXI_PEC_EXTERN_VBUS;
> + val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
> + writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> + val |= SUNXI_PCC_PIPE_CLK_OPEN;
> + writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
> +
> + val = readl(phy->regs + SUNXI_ISCR);
> + val |= SUNXI_ISCR_FORCE_VBUS;
> + writel(val, phy->regs + SUNXI_ISCR);
> +
> + /*
> + * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
> + * registers are directly taken from the BSP USB3 driver from
> + * Allwiner.
> + */
> + writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
> +
> + val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
> + val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
> + SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
> + SUNXI_TX_DEEMPH_3P5DB_MASK);
> + val |= SUNXI_TXVBOOSTLVL(0x7);
> + val |= SUNXI_LOS_BIAS(0x7);
> + val |= SUNXI_TX_SWING_FULL(0x55);
> + val |= SUNXI_TX_DEEMPH_6DB(0x20);
> + val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
> + writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
> +}
> +
> +static int sun50i_usb3_phy_init(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> + int ret;
> +
> + ret = clk_prepare_enable(phy->clk);
> + if (ret)
> + goto err_clk;
> +
> + ret = reset_control_deassert(phy->reset);
> + if (ret)
> + goto err_reset;
> +
> + sun50i_usb3_phy_open(phy);
> + return 0;
> +
> +err_reset:
> + clk_disable_unprepare(phy->clk);
> +
> +err_clk:
> + return ret;
> +}
> +
> +static int sun50i_usb3_phy_exit(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + reset_control_assert(phy->reset);
> + clk_disable_unprepare(phy->clk);
> +
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_on(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_enable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static int sun50i_usb3_phy_power_off(struct phy *_phy)
> +{
> + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
> +
> + if (phy->vbus)
> + return regulator_disable(phy->vbus);
> + else
> + return 0;
> +}
> +
> +static const struct phy_ops sun50i_usb3_phy_ops = {
> + .init = sun50i_usb3_phy_init,
> + .exit = sun50i_usb3_phy_exit,
> + .power_on = sun50i_usb3_phy_power_on,
> + .power_off = sun50i_usb3_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int sun50i_usb3_phy_probe(struct platform_device *pdev)
> +{
> + struct sun50i_usb3_phy *phy;
> + struct device *dev = &pdev->dev;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct device_node *connector_node;
> + int ret;
> +
> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> + if (!phy)
> + return -ENOMEM;
> +
> + dev_set_drvdata(dev, phy);
> +
> + phy->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(phy->clk)) {
> + dev_err(dev, "failed to get phy clock\n");
> + return PTR_ERR(phy->clk);
> + }
> +
> + phy->reset = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(phy->reset)) {
> + dev_err(dev, "failed to get reset control\n");
> + return PTR_ERR(phy->reset);
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + phy->regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(phy->regs))
> + return PTR_ERR(phy->regs);
> +
> + /* Populate the connector as platform device */
> + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
> + if (ret)
> + return ret;
> +
> + /*
> + * Currently the Allwinner USB3 PHY contains only one port, so we
> + * only process one connector now.
> + */
> + connector_node = of_get_next_child(pdev->dev.of_node, NULL);
> +
> + if (connector_node) {
> + /* Get the platform device */
> + phy->connector_dev = of_find_device_by_node(connector_node);
Also of_find_device_by_node takes a reference that needs to be put back in
sun50i_usb3_phy_remove() and error paths. So many refs to take care of,
everywhere. Hmm. :)
I'm just noticing all this now, because I'm writing similar code for
HDMI/connector regualtor borrowing from HDMI controller via of_graph.
regards,
o.
> + if (!phy->connector_dev) {
> + dev_err(dev, "no device for connector\n");
> + return -ENODEV;
> + }
> +
> + phy->vbus = regulator_get(&phy->connector_dev->dev, "vbus");
> + if (IS_ERR(phy->vbus))
> + return PTR_ERR(phy->vbus);
> + }
> +
> + phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
> + if (IS_ERR(phy->phy)) {
> + dev_err(dev, "failed to create PHY\n");
> + return PTR_ERR(phy->phy);
> + }
> +
> + phy_set_drvdata(phy->phy, phy);
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int sun50i_usb3_phy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct sun50i_usb3_phy *phy = dev_get_drvdata(dev);
> +
> + if (phy->vbus)
> + regulator_put(phy->vbus);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id sun50i_usb3_phy_of_match[] = {
> + { .compatible = "allwinner,sun50i-h6-usb3-phy" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
> +
> +static struct platform_driver sun50i_usb3_phy_driver = {
> + .probe = sun50i_usb3_phy_probe,
> + .remove = sun50i_usb3_phy_remove,
> + .driver = {
> + .of_match_table = sun50i_usb3_phy_of_match,
> + .name = "sun50i-usb3-phy",
> + }
> +};
> +module_platform_driver(sun50i_usb3_phy_driver);
> +
> +MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread