* [PATCH 0/3] PCIE support for i.MX8MQ @ 2018-11-17 18:12 Andrey Smirnov 2018-11-17 18:12 ` [PATCH 1/3] PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D Andrey Smirnov ` (4 more replies) 0 siblings, 5 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-17 18:12 UTC (permalink / raw) To: linux-arm-kernel Everyone: This series contains changes I made in order to enable support of PCIE IP block on i.MX8MQ SoCs (full tree can be found at [github-v0]). This series is _very_ preliminary and by no means is ready for inclusion (it also has some unmet dependencies). However is should be in OK enough shape to get some early feedback on, which is the intent of this submission. Specifically, I'd like to get some feedback on whether newly introduced "fsl,iomux-gpr1x" and "fsl,gpr12-device-type" DT properties, added to handle differences between PCIE0 and PCIE1, is a good (acceptable) solution for the problem. All other feedback is appreciated as well! Thank you, Andrey Smirnov [github-v0] https://github.com/ndreys/linux/commits/imx8mq-pcie-v0 Andrey Smirnov (3): PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D PCI: imx: No-op imx6_pcie_reset_phy() on i.MX7D PCI: imx: Add support for i.MX8MQ drivers/pci/controller/dwc/Kconfig | 2 +- drivers/pci/controller/dwc/pci-imx6.c | 119 +++++++++++++++++++++++++- 2 files changed, 117 insertions(+), 4 deletions(-) -- 2.19.1 ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 1/3] PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D 2018-11-17 18:12 [PATCH 0/3] PCIE support for i.MX8MQ Andrey Smirnov @ 2018-11-17 18:12 ` Andrey Smirnov 2018-11-17 18:12 ` [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() " Andrey Smirnov ` (3 subsequent siblings) 4 siblings, 0 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-17 18:12 UTC (permalink / raw) To: linux-arm-kernel PCIE PHY IP block on i.MX7D differs from the one used on i.MX6 family, so none of the code in current implementation of imx6_setup_phy_mpll() is applicable. Cc: bhelgaas at google.com Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: cphealy at gmail.com Cc: l.stach at pengutronix.de Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: "A.s. Dong" <aisheng.dong@nxp.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: linux-imx at nxp.com Cc: linux-arm-kernel at lists.infradead.org Cc: linux-kernel at vger.kernel.org Cc: linux-pci at vger.kernel.org Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> --- drivers/pci/controller/dwc/pci-imx6.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c index 2cbef2d7c207..c140f7987598 100644 --- a/drivers/pci/controller/dwc/pci-imx6.c +++ b/drivers/pci/controller/dwc/pci-imx6.c @@ -525,6 +525,9 @@ static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) int mult, div; u32 val; + if (imx6_pcie->variant == IMX7D) + return 0; + switch (phy_rate) { case 125000000: /* -- 2.19.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() on i.MX7D 2018-11-17 18:12 [PATCH 0/3] PCIE support for i.MX8MQ Andrey Smirnov 2018-11-17 18:12 ` [PATCH 1/3] PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D Andrey Smirnov @ 2018-11-17 18:12 ` Andrey Smirnov 2018-11-20 1:22 ` Trent Piepho 2018-11-17 18:12 ` [PATCH 3/3] PCI: imx: Add support for i.MX8MQ Andrey Smirnov ` (2 subsequent siblings) 4 siblings, 1 reply; 21+ messages in thread From: Andrey Smirnov @ 2018-11-17 18:12 UTC (permalink / raw) To: linux-arm-kernel PCIE PHY IP block on i.MX7D differs from the one used on i.MX6 family, so none of the code in current implementation of imx6_pcie_reset_phy() is applicable. Cc: bhelgaas at google.com Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: cphealy at gmail.com Cc: l.stach at pengutronix.de Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: "A.s. Dong" <aisheng.dong@nxp.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: linux-imx at nxp.com Cc: linux-arm-kernel at lists.infradead.org Cc: linux-kernel at vger.kernel.org Cc: linux-pci at vger.kernel.org Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> --- drivers/pci/controller/dwc/pci-imx6.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c index c140f7987598..3c3002861d25 100644 --- a/drivers/pci/controller/dwc/pci-imx6.c +++ b/drivers/pci/controller/dwc/pci-imx6.c @@ -245,6 +245,9 @@ static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie) { u32 tmp; + if (imx6_pcie->variant == IMX7D) + return; + pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp); tmp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN | PHY_RX_OVRD_IN_LO_RX_PLL_EN); -- 2.19.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() on i.MX7D 2018-11-17 18:12 ` [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() " Andrey Smirnov @ 2018-11-20 1:22 ` Trent Piepho 2018-11-26 18:32 ` Andrey Smirnov 0 siblings, 1 reply; 21+ messages in thread From: Trent Piepho @ 2018-11-20 1:22 UTC (permalink / raw) To: linux-arm-kernel On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > PCIE PHY IP block on i.MX7D differs from the one used on i.MX6 family, > so none of the code in current implementation of imx6_pcie_reset_phy() > is applicable. Tested on IMX7d, still appears to work. Note that your patches will collide with Stefan Agner's patch, "PCI: imx6: limit DBI register length", which was recently posted. He changed the way the variants are handled. That method would allow some of the IMX7D || IMX8MQ checks to be re-written as imx6_pcie->drvdata->boolean_attribute Where the attribute can be set in a table and be re-used in every place it comes into play and updated for new devices in one spot, instead of keeping piles of this version or that version or this other version checks up to date. ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() on i.MX7D 2018-11-20 1:22 ` Trent Piepho @ 2018-11-26 18:32 ` Andrey Smirnov 0 siblings, 0 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-26 18:32 UTC (permalink / raw) To: linux-arm-kernel On Mon, Nov 19, 2018 at 5:22 PM Trent Piepho <tpiepho@impinj.com> wrote: > > On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > > PCIE PHY IP block on i.MX7D differs from the one used on i.MX6 family, > > so none of the code in current implementation of imx6_pcie_reset_phy() > > is applicable. > > Tested on IMX7d, still appears to work. > Thanks for testing! Unless you object, I'll add your Tested-by tag to this patch. > Note that your patches will collide with Stefan Agner's patch, "PCI: > imx6: limit DBI register length", which was recently posted. > > He changed the way the variants are handled. That method would allow > some of the IMX7D || IMX8MQ checks to be re-written as > > imx6_pcie->drvdata->boolean_attribute > > Where the attribute can be set in a table and be re-used in every place > it comes into play and updated for new devices in one spot, instead of > keeping piles of this version or that version or this other version > checks up to date. Thanks for the heads up! I am expecting that I'd have to re-base this series on "next" in PCI tree before it can be applied. This should provide for a good opportunity to discover and resolve all of the conflicts, I think. Thanks, Andrey Smirnov ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-17 18:12 [PATCH 0/3] PCIE support for i.MX8MQ Andrey Smirnov 2018-11-17 18:12 ` [PATCH 1/3] PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D Andrey Smirnov 2018-11-17 18:12 ` [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() " Andrey Smirnov @ 2018-11-17 18:12 ` Andrey Smirnov 2018-11-19 7:07 ` Richard Zhu 2018-11-20 10:48 ` Leonard Crestez 2018-12-03 12:20 ` [PATCH 0/3] PCIE " Lorenzo Pieralisi 2018-12-07 11:37 ` Lorenzo Pieralisi 4 siblings, 2 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-17 18:12 UTC (permalink / raw) To: linux-arm-kernel Cc: bhelgaas at google.com Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: cphealy at gmail.com Cc: l.stach at pengutronix.de Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: "A.s. Dong" <aisheng.dong@nxp.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: linux-imx at nxp.com Cc: linux-arm-kernel at lists.infradead.org Cc: linux-kernel at vger.kernel.org Cc: linux-pci at vger.kernel.org Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> --- drivers/pci/controller/dwc/Kconfig | 2 +- drivers/pci/controller/dwc/pci-imx6.c | 117 ++++++++++++++++++++++++-- 2 files changed, 113 insertions(+), 6 deletions(-) diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig index 91b0194240a5..2b139acccf32 100644 --- a/drivers/pci/controller/dwc/Kconfig +++ b/drivers/pci/controller/dwc/Kconfig @@ -90,7 +90,7 @@ config PCI_EXYNOS config PCI_IMX6 bool "Freescale i.MX6 PCIe controller" - depends on SOC_IMX6Q || (ARM && COMPILE_TEST) + depends on SOC_IMX8MQ || SOC_IMX6Q || (ARM && COMPILE_TEST) depends on PCI_MSI_IRQ_DOMAIN select PCIE_DW_HOST diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c index 3c3002861d25..8d1f310e41a6 100644 --- a/drivers/pci/controller/dwc/pci-imx6.c +++ b/drivers/pci/controller/dwc/pci-imx6.c @@ -8,6 +8,7 @@ * Author: Sean Cross <xobs@kosagi.com> */ +#include <linux/bitfield.h> #include <linux/clk.h> #include <linux/delay.h> #include <linux/gpio.h> @@ -30,6 +31,14 @@ #include "pcie-designware.h" +#define IMX8MQ_PCIE_LINK_CAP_REG_OFFSET 0x7C +#define IMX8MQ_PCIE_LINK_CAP_L1EL_64US (0x6 << 15) + +#define IMX8MQ_GPR_PCIE_REF_USE_PAD BIT(9) +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN BIT(10) +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE BIT(11) + + #define to_imx6_pcie(x) dev_get_drvdata((x)->dev) enum imx6_pcie_variants { @@ -37,6 +46,7 @@ enum imx6_pcie_variants { IMX6SX, IMX6QP, IMX7D, + IMX8MQ, }; struct imx6_pcie { @@ -48,8 +58,10 @@ struct imx6_pcie { struct clk *pcie_inbound_axi; struct clk *pcie; struct regmap *iomuxc_gpr; + u32 gpr1x; struct reset_control *pciephy_reset; struct reset_control *apps_reset; + struct reset_control *apps_clk_req; struct reset_control *turnoff_reset; enum imx6_pcie_variants variant; u32 tx_deemph_gen1; @@ -59,6 +71,7 @@ struct imx6_pcie { u32 tx_swing_low; int link_gen; struct regulator *vpcie; + u32 device_type[2]; }; /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */ @@ -245,7 +258,8 @@ static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie) { u32 tmp; - if (imx6_pcie->variant == IMX7D) + if (imx6_pcie->variant == IMX7D || + imx6_pcie->variant == IMX8MQ) return; pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp); @@ -261,6 +275,7 @@ static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie) pcie_phy_write(imx6_pcie, PHY_RX_OVRD_IN_LO, tmp); } +#ifdef CONFIG_ARM /* Added for PCI abort handling */ static int imx6q_pcie_abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs) @@ -294,6 +309,7 @@ static int imx6q_pcie_abort_handler(unsigned long addr, return 1; } +#endif static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie) { @@ -301,6 +317,7 @@ static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie) switch (imx6_pcie->variant) { case IMX7D: + case IMX8MQ: /* FALLTHROUGH */ reset_control_assert(imx6_pcie->pciephy_reset); reset_control_assert(imx6_pcie->apps_reset); break; @@ -369,6 +386,18 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie) break; case IMX7D: break; + case IMX8MQ: + /* + * Set the over ride low and enabled + * make sure that REF_CLK is turned on. + */ + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE, + 0); + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN); + break; } return ret; @@ -397,6 +426,7 @@ static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie) { struct dw_pcie *pci = imx6_pcie->pci; struct device *dev = pci->dev; + unsigned int val; int ret; if (imx6_pcie->vpcie && !regulator_is_enabled(imx6_pcie->vpcie)) { @@ -445,6 +475,29 @@ static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie) } switch (imx6_pcie->variant) { + case IMX8MQ: + reset_control_deassert(imx6_pcie->pciephy_reset); + udelay(100); + /* + * Configure the CLK_REQ# high, let the L1SS + * automatically controlled by HW. + */ + reset_control_assert(imx6_pcie->apps_clk_req); + + /* + * Configure the L1 latency of rc to less than 64us + * Otherwise, the L1/L1SUB wouldn't be enable by ASPM. + */ + val = dw_pcie_readl_dbi(imx6_pcie->pci, + SZ_1M + + IMX8MQ_PCIE_LINK_CAP_REG_OFFSET); + val &= ~PCI_EXP_LNKCAP_L1EL; + val |= IMX8MQ_PCIE_LINK_CAP_L1EL_64US; + dw_pcie_writel_dbi(imx6_pcie->pci, + SZ_1M + + IMX8MQ_PCIE_LINK_CAP_REG_OFFSET, + val); + break; case IMX7D: reset_control_deassert(imx6_pcie->pciephy_reset); imx7d_pcie_wait_for_phy_pll_lock(imx6_pcie); @@ -483,6 +536,15 @@ static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie) static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie) { switch (imx6_pcie->variant) { + case IMX8MQ: + /* + * TODO: Currently this code assumes external + * oscillator is being used + */ + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, + IMX8MQ_GPR_PCIE_REF_USE_PAD, + IMX8MQ_GPR_PCIE_REF_USE_PAD); + break; case IMX7D: regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0); @@ -519,7 +581,8 @@ static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie) } regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, - IMX6Q_GPR12_DEVICE_TYPE, PCI_EXP_TYPE_ROOT_PORT << 12); + imx6_pcie->device_type[0], + imx6_pcie->device_type[1]); } static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) @@ -528,7 +591,8 @@ static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) int mult, div; u32 val; - if (imx6_pcie->variant == IMX7D) + if (imx6_pcie->variant == IMX7D || + imx6_pcie->variant == IMX8MQ) return 0; switch (phy_rate) { @@ -616,6 +680,7 @@ static void imx6_pcie_ltssm_enable(struct device *dev) IMX6Q_GPR12_PCIE_CTL_2); break; case IMX7D: + case IMX8MQ: /* FALLTHROUGH */ reset_control_deassert(imx6_pcie->apps_reset); break; } @@ -798,10 +863,24 @@ static void imx6_pcie_clk_disable(struct imx6_pcie *imx6_pcie) clk_disable_unprepare(imx6_pcie->pcie_phy); clk_disable_unprepare(imx6_pcie->pcie_bus); - if (imx6_pcie->variant == IMX7D) { + switch (imx6_pcie->variant) { + case IMX7D: regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, IMX7D_GPR12_PCIE_PHY_REFCLK_SEL); + break; + /* + * Disable the override. Configure the CLK_REQ# high, let the + * L1SS automatically controlled by HW when link is up. + * Otherwise, turn off the REF_CLK to save power consumption. + */ + case IMX8MQ: + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, + 0); + break; + default: + break; } } @@ -870,6 +949,10 @@ static int imx6_pcie_probe(struct platform_device *pdev) imx6_pcie->variant = (enum imx6_pcie_variants)of_device_get_match_data(dev); + imx6_pcie->device_type[0] = IMX6Q_GPR12_DEVICE_TYPE; + imx6_pcie->device_type[1] = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, + PCI_EXP_TYPE_ROOT_PORT); + dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); pci->dbi_base = devm_ioremap_resource(dev, dbi_base); if (IS_ERR(pci->dbi_base)) @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) return PTR_ERR(imx6_pcie->pcie_inbound_axi); } break; - case IMX7D: + case IMX8MQ: + if (of_property_read_u32(node, "fsl,iomux-gpr1x", + &imx6_pcie->gpr1x)) { + dev_err(dev, "Failed to get GPR1x address\n"); + return -EINVAL; + } + + if (of_property_read_u32_array( + node, "fsl,gpr12-device-type", + imx6_pcie->device_type, + ARRAY_SIZE(imx6_pcie->device_type))) { + dev_err(dev, "Failed to get device type mask/value\n"); + return -EINVAL; + } + + imx6_pcie->apps_clk_req = + devm_reset_control_get_exclusive(dev, "clkreq"); + if (IS_ERR(imx6_pcie->apps_clk_req)) { + dev_err(dev, "Failed to get PCIE APPS CLK_REQ# reset control\n"); + return PTR_ERR(imx6_pcie->apps_clk_req); + } + case IMX7D: /* FALLTHROUGH */ imx6_pcie->pciephy_reset = devm_reset_control_get_exclusive(dev, "pciephy"); if (IS_ERR(imx6_pcie->pciephy_reset)) { @@ -1011,6 +1115,7 @@ static const struct of_device_id imx6_pcie_of_match[] = { { .compatible = "fsl,imx6sx-pcie", .data = (void *)IMX6SX, }, { .compatible = "fsl,imx6qp-pcie", .data = (void *)IMX6QP, }, { .compatible = "fsl,imx7d-pcie", .data = (void *)IMX7D, }, + { .compatible = "fsl,imx8mq-pcie", .data = (void *)IMX8MQ, } , {}, }; @@ -1027,6 +1132,7 @@ static struct platform_driver imx6_pcie_driver = { static int __init imx6_pcie_init(void) { +#ifdef CONFIG_ARM /* * Since probe() can be deferred we need to make sure that * hook_fault_code is not called after __init memory is freed @@ -1036,6 +1142,7 @@ static int __init imx6_pcie_init(void) */ hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, "external abort on non-linefetch"); +#endif return platform_driver_register(&imx6_pcie_driver); } -- 2.19.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-17 18:12 ` [PATCH 3/3] PCI: imx: Add support for i.MX8MQ Andrey Smirnov @ 2018-11-19 7:07 ` Richard Zhu 2018-11-26 18:09 ` Andrey Smirnov 2018-11-20 10:48 ` Leonard Crestez 1 sibling, 1 reply; 21+ messages in thread From: Richard Zhu @ 2018-11-19 7:07 UTC (permalink / raw) To: linux-arm-kernel Hi Andrey: Thanks for your patch-set. I have comment about the L1SS implementation below. It's better to figure out one method to fix it. BR Richard > -----Original Message----- > From: Andrey Smirnov [mailto:andrew.smirnov at gmail.com] > Sent: 2018?11?18? 2:12 > To: linux-kernel at vger.kernel.org > Cc: Andrey Smirnov <andrew.smirnov@gmail.com>; bhelgaas at google.com; > Fabio Estevam <fabio.estevam@nxp.com>; cphealy at gmail.com; > l.stach at pengutronix.de; Leonard Crestez <leonard.crestez@nxp.com>; > Aisheng DONG <aisheng.dong@nxp.com>; Richard Zhu > <hongxing.zhu@nxp.com>; dl-linux-imx <linux-imx@nxp.com>; > linux-arm-kernel at lists.infradead.org; linux-pci at vger.kernel.org > Subject: [PATCH 3/3] PCI: imx: Add support for i.MX8MQ > > Cc: bhelgaas at google.com > Cc: Fabio Estevam <fabio.estevam@nxp.com> > Cc: cphealy at gmail.com > Cc: l.stach at pengutronix.de > Cc: Leonard Crestez <leonard.crestez@nxp.com> > Cc: "A.s. Dong" <aisheng.dong@nxp.com> > Cc: Richard Zhu <hongxing.zhu@nxp.com> > Cc: linux-imx at nxp.com > Cc: linux-arm-kernel at lists.infradead.org > Cc: linux-kernel at vger.kernel.org > Cc: linux-pci at vger.kernel.org > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> > --- > drivers/pci/controller/dwc/Kconfig | 2 +- > drivers/pci/controller/dwc/pci-imx6.c | 117 ++++++++++++++++++++++++-- > 2 files changed, 113 insertions(+), 6 deletions(-) > > diff --git a/drivers/pci/controller/dwc/Kconfig > b/drivers/pci/controller/dwc/Kconfig > index 91b0194240a5..2b139acccf32 100644 > --- a/drivers/pci/controller/dwc/Kconfig > +++ b/drivers/pci/controller/dwc/Kconfig > @@ -90,7 +90,7 @@ config PCI_EXYNOS > > config PCI_IMX6 > bool "Freescale i.MX6 PCIe controller" > - depends on SOC_IMX6Q || (ARM && COMPILE_TEST) > + depends on SOC_IMX8MQ || SOC_IMX6Q || (ARM && COMPILE_TEST) > depends on PCI_MSI_IRQ_DOMAIN > select PCIE_DW_HOST > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c > b/drivers/pci/controller/dwc/pci-imx6.c > index 3c3002861d25..8d1f310e41a6 100644 > --- a/drivers/pci/controller/dwc/pci-imx6.c > +++ b/drivers/pci/controller/dwc/pci-imx6.c > @@ -8,6 +8,7 @@ > * Author: Sean Cross <xobs@kosagi.com> > */ > > +#include <linux/bitfield.h> > #include <linux/clk.h> > #include <linux/delay.h> > #include <linux/gpio.h> > @@ -30,6 +31,14 @@ > > #include "pcie-designware.h" > > +#define IMX8MQ_PCIE_LINK_CAP_REG_OFFSET 0x7C > +#define IMX8MQ_PCIE_LINK_CAP_L1EL_64US (0x6 << 15) > + > +#define IMX8MQ_GPR_PCIE_REF_USE_PAD BIT(9) > +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN BIT(10) > +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE BIT(11) > + > + > #define to_imx6_pcie(x) dev_get_drvdata((x)->dev) > > enum imx6_pcie_variants { > @@ -37,6 +46,7 @@ enum imx6_pcie_variants { > IMX6SX, > IMX6QP, > IMX7D, > + IMX8MQ, > }; > > struct imx6_pcie { > @@ -48,8 +58,10 @@ struct imx6_pcie { > struct clk *pcie_inbound_axi; > struct clk *pcie; > struct regmap *iomuxc_gpr; > + u32 gpr1x; > struct reset_control *pciephy_reset; > struct reset_control *apps_reset; > + struct reset_control *apps_clk_req; > struct reset_control *turnoff_reset; > enum imx6_pcie_variants variant; > u32 tx_deemph_gen1; > @@ -59,6 +71,7 @@ struct imx6_pcie { > u32 tx_swing_low; > int link_gen; > struct regulator *vpcie; > + u32 device_type[2]; > }; > > /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */ @@ > -245,7 +258,8 @@ static void imx6_pcie_reset_phy(struct imx6_pcie > *imx6_pcie) { > u32 tmp; > > - if (imx6_pcie->variant == IMX7D) > + if (imx6_pcie->variant == IMX7D || > + imx6_pcie->variant == IMX8MQ) > return; > > pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp); @@ -261,6 > +275,7 @@ static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie) > pcie_phy_write(imx6_pcie, PHY_RX_OVRD_IN_LO, tmp); } > > +#ifdef CONFIG_ARM > /* Added for PCI abort handling */ > static int imx6q_pcie_abort_handler(unsigned long addr, > unsigned int fsr, struct pt_regs *regs) @@ -294,6 +309,7 @@ static > int imx6q_pcie_abort_handler(unsigned long addr, > > return 1; > } > +#endif > > static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie) > { @@ -301,6 +317,7 @@ static void imx6_pcie_assert_core_reset(struct > imx6_pcie *imx6_pcie) > > switch (imx6_pcie->variant) { > case IMX7D: > + case IMX8MQ: /* FALLTHROUGH */ > reset_control_assert(imx6_pcie->pciephy_reset); > reset_control_assert(imx6_pcie->apps_reset); > break; > @@ -369,6 +386,18 @@ static int imx6_pcie_enable_ref_clk(struct > imx6_pcie *imx6_pcie) > break; > case IMX7D: > break; > + case IMX8MQ: > + /* > + * Set the over ride low and enabled > + * make sure that REF_CLK is turned on. > + */ > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE, > + 0); > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN); > + break; > } > > return ret; > @@ -397,6 +426,7 @@ static void imx6_pcie_deassert_core_reset(struct > imx6_pcie *imx6_pcie) { > struct dw_pcie *pci = imx6_pcie->pci; > struct device *dev = pci->dev; > + unsigned int val; > int ret; > > if (imx6_pcie->vpcie && !regulator_is_enabled(imx6_pcie->vpcie)) { @@ > -445,6 +475,29 @@ static void imx6_pcie_deassert_core_reset(struct > imx6_pcie *imx6_pcie) > } > > switch (imx6_pcie->variant) { > + case IMX8MQ: > + reset_control_deassert(imx6_pcie->pciephy_reset); > + udelay(100); > + /* > + * Configure the CLK_REQ# high, let the L1SS > + * automatically controlled by HW. > + */ > + reset_control_assert(imx6_pcie->apps_clk_req); > + > + /* > + * Configure the L1 latency of rc to less than 64us > + * Otherwise, the L1/L1SUB wouldn't be enable by ASPM. > + */ > + val = dw_pcie_readl_dbi(imx6_pcie->pci, > + SZ_1M + > + IMX8MQ_PCIE_LINK_CAP_REG_OFFSET); > + val &= ~PCI_EXP_LNKCAP_L1EL; > + val |= IMX8MQ_PCIE_LINK_CAP_L1EL_64US; > + dw_pcie_writel_dbi(imx6_pcie->pci, > + SZ_1M + > + IMX8MQ_PCIE_LINK_CAP_REG_OFFSET, > + val); > + break; > case IMX7D: > reset_control_deassert(imx6_pcie->pciephy_reset); > imx7d_pcie_wait_for_phy_pll_lock(imx6_pcie); > @@ -483,6 +536,15 @@ static void imx6_pcie_deassert_core_reset(struct > imx6_pcie *imx6_pcie) static void imx6_pcie_init_phy(struct imx6_pcie > *imx6_pcie) { > switch (imx6_pcie->variant) { > + case IMX8MQ: > + /* > + * TODO: Currently this code assumes external > + * oscillator is being used > + */ > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > + IMX8MQ_GPR_PCIE_REF_USE_PAD, > + IMX8MQ_GPR_PCIE_REF_USE_PAD); > + break; > case IMX7D: > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0); @@ > -519,7 +581,8 @@ static void imx6_pcie_init_phy(struct imx6_pcie > *imx6_pcie) > } > > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > - IMX6Q_GPR12_DEVICE_TYPE, PCI_EXP_TYPE_ROOT_PORT << > 12); > + imx6_pcie->device_type[0], > + imx6_pcie->device_type[1]); > } > > static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) @@ -528,7 > +591,8 @@ static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) > int mult, div; > u32 val; > > - if (imx6_pcie->variant == IMX7D) > + if (imx6_pcie->variant == IMX7D || > + imx6_pcie->variant == IMX8MQ) > return 0; > > switch (phy_rate) { > @@ -616,6 +680,7 @@ static void imx6_pcie_ltssm_enable(struct device > *dev) > IMX6Q_GPR12_PCIE_CTL_2); > break; > case IMX7D: > + case IMX8MQ: /* FALLTHROUGH */ > reset_control_deassert(imx6_pcie->apps_reset); > break; > } > @@ -798,10 +863,24 @@ static void imx6_pcie_clk_disable(struct imx6_pcie > *imx6_pcie) > clk_disable_unprepare(imx6_pcie->pcie_phy); > clk_disable_unprepare(imx6_pcie->pcie_bus); > > - if (imx6_pcie->variant == IMX7D) { > + switch (imx6_pcie->variant) { > + case IMX7D: > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL); > + break; > + /* > + * Disable the override. Configure the CLK_REQ# high, let the > + * L1SS automatically controlled by HW when link is up. > + * Otherwise, turn off the REF_CLK to save power consumption. > + */ [Richard Zhu] About the L1SS support, there is a back-compatible issue. When one none-L1SS capability EP device is used in one HW design solution. In this case, EP device wouldn't manipulated its own CLK_REQ#. The CLK_REQ# would be high when the override_en is disabled here. That means the REFCLK would be turned off abnormally. System would have problem when the REFCLK of PCIe is turned off abnormally after link is up. > + case IMX8MQ: > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, > + 0); > + break; > + default: > + break; > } > } > > @@ -870,6 +949,10 @@ static int imx6_pcie_probe(struct platform_device > *pdev) > imx6_pcie->variant = > (enum imx6_pcie_variants)of_device_get_match_data(dev); > > + imx6_pcie->device_type[0] = IMX6Q_GPR12_DEVICE_TYPE; > + imx6_pcie->device_type[1] = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, > + PCI_EXP_TYPE_ROOT_PORT); > + > dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); > pci->dbi_base = devm_ioremap_resource(dev, dbi_base); > if (IS_ERR(pci->dbi_base)) > @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device > *pdev) > return PTR_ERR(imx6_pcie->pcie_inbound_axi); > } > break; > - case IMX7D: > + case IMX8MQ: > + if (of_property_read_u32(node, "fsl,iomux-gpr1x", > + &imx6_pcie->gpr1x)) { > + dev_err(dev, "Failed to get GPR1x address\n"); > + return -EINVAL; > + } > + > + if (of_property_read_u32_array( > + node, "fsl,gpr12-device-type", > + imx6_pcie->device_type, > + ARRAY_SIZE(imx6_pcie->device_type))) { > + dev_err(dev, "Failed to get device type mask/value\n"); > + return -EINVAL; > + } > + > + imx6_pcie->apps_clk_req = > + devm_reset_control_get_exclusive(dev, "clkreq"); > + if (IS_ERR(imx6_pcie->apps_clk_req)) { > + dev_err(dev, "Failed to get PCIE APPS CLK_REQ# reset > control\n"); > + return PTR_ERR(imx6_pcie->apps_clk_req); > + } > + case IMX7D: /* FALLTHROUGH */ > imx6_pcie->pciephy_reset = > devm_reset_control_get_exclusive(dev, > "pciephy"); > if (IS_ERR(imx6_pcie->pciephy_reset)) { @@ -1011,6 +1115,7 @@ > static const struct of_device_id imx6_pcie_of_match[] = { > { .compatible = "fsl,imx6sx-pcie", .data = (void *)IMX6SX, }, > { .compatible = "fsl,imx6qp-pcie", .data = (void *)IMX6QP, }, > { .compatible = "fsl,imx7d-pcie", .data = (void *)IMX7D, }, > + { .compatible = "fsl,imx8mq-pcie", .data = (void *)IMX8MQ, } , > {}, > }; > > @@ -1027,6 +1132,7 @@ static struct platform_driver imx6_pcie_driver = { > > static int __init imx6_pcie_init(void) > { > +#ifdef CONFIG_ARM > /* > * Since probe() can be deferred we need to make sure that > * hook_fault_code is not called after __init memory is freed @@ > -1036,6 +1142,7 @@ static int __init imx6_pcie_init(void) > */ > hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, > "external abort on non-linefetch"); > +#endif > > return platform_driver_register(&imx6_pcie_driver); > } > -- > 2.19.1 ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-19 7:07 ` Richard Zhu @ 2018-11-26 18:09 ` Andrey Smirnov 2018-11-29 10:52 ` Richard Zhu 0 siblings, 1 reply; 21+ messages in thread From: Andrey Smirnov @ 2018-11-26 18:09 UTC (permalink / raw) To: linux-arm-kernel On Sun, Nov 18, 2018 at 11:07 PM Richard Zhu <hongxing.zhu@nxp.com> wrote: > > Hi Andrey: > Thanks for your patch-set. > I have comment about the L1SS implementation below. > It's better to figure out one method to fix it. > > BR > Richard > > > -----Original Message----- > > From: Andrey Smirnov [mailto:andrew.smirnov at gmail.com] > > Sent: 2018?11?18? 2:12 > > To: linux-kernel at vger.kernel.org > > Cc: Andrey Smirnov <andrew.smirnov@gmail.com>; bhelgaas at google.com; > > Fabio Estevam <fabio.estevam@nxp.com>; cphealy at gmail.com; > > l.stach at pengutronix.de; Leonard Crestez <leonard.crestez@nxp.com>; > > Aisheng DONG <aisheng.dong@nxp.com>; Richard Zhu > > <hongxing.zhu@nxp.com>; dl-linux-imx <linux-imx@nxp.com>; > > linux-arm-kernel at lists.infradead.org; linux-pci at vger.kernel.org > > Subject: [PATCH 3/3] PCI: imx: Add support for i.MX8MQ > > > > Cc: bhelgaas at google.com > > Cc: Fabio Estevam <fabio.estevam@nxp.com> > > Cc: cphealy at gmail.com > > Cc: l.stach at pengutronix.de > > Cc: Leonard Crestez <leonard.crestez@nxp.com> > > Cc: "A.s. Dong" <aisheng.dong@nxp.com> > > Cc: Richard Zhu <hongxing.zhu@nxp.com> > > Cc: linux-imx at nxp.com > > Cc: linux-arm-kernel at lists.infradead.org > > Cc: linux-kernel at vger.kernel.org > > Cc: linux-pci at vger.kernel.org > > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> > > --- > > drivers/pci/controller/dwc/Kconfig | 2 +- > > drivers/pci/controller/dwc/pci-imx6.c | 117 ++++++++++++++++++++++++-- > > 2 files changed, 113 insertions(+), 6 deletions(-) > > > > diff --git a/drivers/pci/controller/dwc/Kconfig > > b/drivers/pci/controller/dwc/Kconfig > > index 91b0194240a5..2b139acccf32 100644 > > --- a/drivers/pci/controller/dwc/Kconfig > > +++ b/drivers/pci/controller/dwc/Kconfig > > @@ -90,7 +90,7 @@ config PCI_EXYNOS > > > > config PCI_IMX6 > > bool "Freescale i.MX6 PCIe controller" > > - depends on SOC_IMX6Q || (ARM && COMPILE_TEST) > > + depends on SOC_IMX8MQ || SOC_IMX6Q || (ARM && COMPILE_TEST) > > depends on PCI_MSI_IRQ_DOMAIN > > select PCIE_DW_HOST > > > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c > > b/drivers/pci/controller/dwc/pci-imx6.c > > index 3c3002861d25..8d1f310e41a6 100644 > > --- a/drivers/pci/controller/dwc/pci-imx6.c > > +++ b/drivers/pci/controller/dwc/pci-imx6.c > > @@ -8,6 +8,7 @@ > > * Author: Sean Cross <xobs@kosagi.com> > > */ > > > > +#include <linux/bitfield.h> > > #include <linux/clk.h> > > #include <linux/delay.h> > > #include <linux/gpio.h> > > @@ -30,6 +31,14 @@ > > > > #include "pcie-designware.h" > > > > +#define IMX8MQ_PCIE_LINK_CAP_REG_OFFSET 0x7C > > +#define IMX8MQ_PCIE_LINK_CAP_L1EL_64US (0x6 << 15) > > + > > +#define IMX8MQ_GPR_PCIE_REF_USE_PAD BIT(9) > > +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN BIT(10) > > +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE BIT(11) > > + > > + > > #define to_imx6_pcie(x) dev_get_drvdata((x)->dev) > > > > enum imx6_pcie_variants { > > @@ -37,6 +46,7 @@ enum imx6_pcie_variants { > > IMX6SX, > > IMX6QP, > > IMX7D, > > + IMX8MQ, > > }; > > > > struct imx6_pcie { > > @@ -48,8 +58,10 @@ struct imx6_pcie { > > struct clk *pcie_inbound_axi; > > struct clk *pcie; > > struct regmap *iomuxc_gpr; > > + u32 gpr1x; > > struct reset_control *pciephy_reset; > > struct reset_control *apps_reset; > > + struct reset_control *apps_clk_req; > > struct reset_control *turnoff_reset; > > enum imx6_pcie_variants variant; > > u32 tx_deemph_gen1; > > @@ -59,6 +71,7 @@ struct imx6_pcie { > > u32 tx_swing_low; > > int link_gen; > > struct regulator *vpcie; > > + u32 device_type[2]; > > }; > > > > /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */ @@ > > -245,7 +258,8 @@ static void imx6_pcie_reset_phy(struct imx6_pcie > > *imx6_pcie) { > > u32 tmp; > > > > - if (imx6_pcie->variant == IMX7D) > > + if (imx6_pcie->variant == IMX7D || > > + imx6_pcie->variant == IMX8MQ) > > return; > > > > pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp); @@ -261,6 > > +275,7 @@ static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie) > > pcie_phy_write(imx6_pcie, PHY_RX_OVRD_IN_LO, tmp); } > > > > +#ifdef CONFIG_ARM > > /* Added for PCI abort handling */ > > static int imx6q_pcie_abort_handler(unsigned long addr, > > unsigned int fsr, struct pt_regs *regs) @@ -294,6 +309,7 @@ static > > int imx6q_pcie_abort_handler(unsigned long addr, > > > > return 1; > > } > > +#endif > > > > static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie) > > { @@ -301,6 +317,7 @@ static void imx6_pcie_assert_core_reset(struct > > imx6_pcie *imx6_pcie) > > > > switch (imx6_pcie->variant) { > > case IMX7D: > > + case IMX8MQ: /* FALLTHROUGH */ > > reset_control_assert(imx6_pcie->pciephy_reset); > > reset_control_assert(imx6_pcie->apps_reset); > > break; > > @@ -369,6 +386,18 @@ static int imx6_pcie_enable_ref_clk(struct > > imx6_pcie *imx6_pcie) > > break; > > case IMX7D: > > break; > > + case IMX8MQ: > > + /* > > + * Set the over ride low and enabled > > + * make sure that REF_CLK is turned on. > > + */ > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE, > > + 0); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, > > + IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN); > > + break; > > } > > > > return ret; > > @@ -397,6 +426,7 @@ static void imx6_pcie_deassert_core_reset(struct > > imx6_pcie *imx6_pcie) { > > struct dw_pcie *pci = imx6_pcie->pci; > > struct device *dev = pci->dev; > > + unsigned int val; > > int ret; > > > > if (imx6_pcie->vpcie && !regulator_is_enabled(imx6_pcie->vpcie)) { @@ > > -445,6 +475,29 @@ static void imx6_pcie_deassert_core_reset(struct > > imx6_pcie *imx6_pcie) > > } > > > > switch (imx6_pcie->variant) { > > + case IMX8MQ: > > + reset_control_deassert(imx6_pcie->pciephy_reset); > > + udelay(100); > > + /* > > + * Configure the CLK_REQ# high, let the L1SS > > + * automatically controlled by HW. > > + */ > > + reset_control_assert(imx6_pcie->apps_clk_req); > > + > > + /* > > + * Configure the L1 latency of rc to less than 64us > > + * Otherwise, the L1/L1SUB wouldn't be enable by ASPM. > > + */ > > + val = dw_pcie_readl_dbi(imx6_pcie->pci, > > + SZ_1M + > > + IMX8MQ_PCIE_LINK_CAP_REG_OFFSET); > > + val &= ~PCI_EXP_LNKCAP_L1EL; > > + val |= IMX8MQ_PCIE_LINK_CAP_L1EL_64US; > > + dw_pcie_writel_dbi(imx6_pcie->pci, > > + SZ_1M + > > + IMX8MQ_PCIE_LINK_CAP_REG_OFFSET, > > + val); > > + break; > > case IMX7D: > > reset_control_deassert(imx6_pcie->pciephy_reset); > > imx7d_pcie_wait_for_phy_pll_lock(imx6_pcie); > > @@ -483,6 +536,15 @@ static void imx6_pcie_deassert_core_reset(struct > > imx6_pcie *imx6_pcie) static void imx6_pcie_init_phy(struct imx6_pcie > > *imx6_pcie) { > > switch (imx6_pcie->variant) { > > + case IMX8MQ: > > + /* > > + * TODO: Currently this code assumes external > > + * oscillator is being used > > + */ > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, imx6_pcie->gpr1x, > > + IMX8MQ_GPR_PCIE_REF_USE_PAD, > > + IMX8MQ_GPR_PCIE_REF_USE_PAD); > > + break; > > case IMX7D: > > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0); @@ > > -519,7 +581,8 @@ static void imx6_pcie_init_phy(struct imx6_pcie > > *imx6_pcie) > > } > > > > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > > - IMX6Q_GPR12_DEVICE_TYPE, PCI_EXP_TYPE_ROOT_PORT << > > 12); > > + imx6_pcie->device_type[0], > > + imx6_pcie->device_type[1]); > > } > > > > static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) @@ -528,7 > > +591,8 @@ static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) > > int mult, div; > > u32 val; > > > > - if (imx6_pcie->variant == IMX7D) > > + if (imx6_pcie->variant == IMX7D || > > + imx6_pcie->variant == IMX8MQ) > > return 0; > > > > switch (phy_rate) { > > @@ -616,6 +680,7 @@ static void imx6_pcie_ltssm_enable(struct device > > *dev) > > IMX6Q_GPR12_PCIE_CTL_2); > > break; > > case IMX7D: > > + case IMX8MQ: /* FALLTHROUGH */ > > reset_control_deassert(imx6_pcie->apps_reset); > > break; > > } > > @@ -798,10 +863,24 @@ static void imx6_pcie_clk_disable(struct imx6_pcie > > *imx6_pcie) > > clk_disable_unprepare(imx6_pcie->pcie_phy); > > clk_disable_unprepare(imx6_pcie->pcie_bus); > > > > - if (imx6_pcie->variant == IMX7D) { > > + switch (imx6_pcie->variant) { > > + case IMX7D: > > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, > > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL); > > + break; > > + /* > > + * Disable the override. Configure the CLK_REQ# high, let the > > + * L1SS automatically controlled by HW when link is up. > > + * Otherwise, turn off the REF_CLK to save power consumption. > > + */ > [Richard Zhu] About the L1SS support, there is a back-compatible issue. > When one none-L1SS capability EP device is used in one HW design solution. > In this case, EP device wouldn't manipulated its own CLK_REQ#. > The CLK_REQ# would be high when the override_en is disabled here. > That means the REFCLK would be turned off abnormally. > System would have problem when the REFCLK of PCIe is turned off abnormally after link is up. > I don't have a lot of expertise in this area, so please take my comment with a grain of salt. The way I understand it, is in legacy systems that do not support L1SS with CLKREQ that feature shouldn't be enabled/used. Unless I've missed something, I think it should be possible to do so and disable the feature by configuring corresponding CLKREQ_B pad as GPIO and adding a GPIO hog node to pull CLKREQ low. Do you see any problems with this approach? Regardless though, I wasn't really planning on including PM support in this series. The code in question shouldn't even be in the patch since it'll never be executed because imx6_pcie_clk_disable() is only called by imx6_pcie_suspend_noirq() which is a no-op on all variants except i.MX7D. I'll drop all of the unused PM-related bits I missed from the series and we can add them later in a separate submission. Thanks, Andrey Smirnov ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-26 18:09 ` Andrey Smirnov @ 2018-11-29 10:52 ` Richard Zhu 0 siblings, 0 replies; 21+ messages in thread From: Richard Zhu @ 2018-11-29 10:52 UTC (permalink / raw) To: linux-arm-kernel > -----Original Message----- > From: Andrey Smirnov [mailto:andrew.smirnov at gmail.com] > Sent: 2018?11?27? 2:10 > To: Richard Zhu <hongxing.zhu@nxp.com> > Cc: linux-kernel <linux-kernel@vger.kernel.org>; Bjorn Helgaas > <bhelgaas@google.com>; Fabio Estevam <fabio.estevam@nxp.com>; Chris > Healy <cphealy@gmail.com>; Lucas Stach <l.stach@pengutronix.de>; > Leonard Crestez <leonard.crestez@nxp.com>; Aisheng DONG > <aisheng.dong@nxp.com>; dl-linux-imx <linux-imx@nxp.com>; > linux-arm-kernel <linux-arm-kernel@lists.infradead.org>; > linux-pci at vger.kernel.org > Subject: Re: [PATCH 3/3] PCI: imx: Add support for i.MX8MQ > > On Sun, Nov 18, 2018 at 11:07 PM Richard Zhu <hongxing.zhu@nxp.com> > wrote: > > > > Hi Andrey: > > Thanks for your patch-set. > > I have comment about the L1SS implementation below. > > It's better to figure out one method to fix it. > > > > BR > > Richard > > > > > -----Original Message----- > > > From: Andrey Smirnov [mailto:andrew.smirnov at gmail.com] > > > Sent: 2018?11?18? 2:12 > > > To: linux-kernel at vger.kernel.org > > > Cc: Andrey Smirnov <andrew.smirnov@gmail.com>; > bhelgaas at google.com; > > > Fabio Estevam <fabio.estevam@nxp.com>; cphealy at gmail.com; > > > l.stach at pengutronix.de; Leonard Crestez <leonard.crestez@nxp.com>; > > > Aisheng DONG <aisheng.dong@nxp.com>; Richard Zhu > > > <hongxing.zhu@nxp.com>; dl-linux-imx <linux-imx@nxp.com>; > > > linux-arm-kernel at lists.infradead.org; linux-pci at vger.kernel.org > > > Subject: [PATCH 3/3] PCI: imx: Add support for i.MX8MQ > > > > > > Cc: bhelgaas at google.com > > > Cc: Fabio Estevam <fabio.estevam@nxp.com> > > > Cc: cphealy at gmail.com > > > Cc: l.stach at pengutronix.de > > > Cc: Leonard Crestez <leonard.crestez@nxp.com> > > > Cc: "A.s. Dong" <aisheng.dong@nxp.com> > > > Cc: Richard Zhu <hongxing.zhu@nxp.com> > > > Cc: linux-imx at nxp.com > > > Cc: linux-arm-kernel at lists.infradead.org > > > Cc: linux-kernel at vger.kernel.org > > > Cc: linux-pci at vger.kernel.org > > > Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> > > > --- > > > drivers/pci/controller/dwc/Kconfig | 2 +- > > > drivers/pci/controller/dwc/pci-imx6.c | 117 > > > ++++++++++++++++++++++++-- > > > 2 files changed, 113 insertions(+), 6 deletions(-) > > > > > > diff --git a/drivers/pci/controller/dwc/Kconfig > > > b/drivers/pci/controller/dwc/Kconfig > > > index 91b0194240a5..2b139acccf32 100644 > > > --- a/drivers/pci/controller/dwc/Kconfig > > > +++ b/drivers/pci/controller/dwc/Kconfig > > > @@ -90,7 +90,7 @@ config PCI_EXYNOS > > > > > > config PCI_IMX6 > > > bool "Freescale i.MX6 PCIe controller" > > > - depends on SOC_IMX6Q || (ARM && COMPILE_TEST) > > > + depends on SOC_IMX8MQ || SOC_IMX6Q || (ARM && > COMPILE_TEST) > > > depends on PCI_MSI_IRQ_DOMAIN > > > select PCIE_DW_HOST > > > > > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c > > > b/drivers/pci/controller/dwc/pci-imx6.c > > > index 3c3002861d25..8d1f310e41a6 100644 > > > --- a/drivers/pci/controller/dwc/pci-imx6.c > > > +++ b/drivers/pci/controller/dwc/pci-imx6.c > > > @@ -8,6 +8,7 @@ > > > * Author: Sean Cross <xobs@kosagi.com> > > > */ > > > > > > +#include <linux/bitfield.h> > > > #include <linux/clk.h> > > > #include <linux/delay.h> > > > #include <linux/gpio.h> > > > @@ -30,6 +31,14 @@ > > > > > > #include "pcie-designware.h" > > > > > > +#define IMX8MQ_PCIE_LINK_CAP_REG_OFFSET 0x7C > > > +#define IMX8MQ_PCIE_LINK_CAP_L1EL_64US (0x6 << > 15) > > > + > > > +#define IMX8MQ_GPR_PCIE_REF_USE_PAD BIT(9) > > > +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN BIT(10) > > > +#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE BIT(11) > > > + > > > + > > > #define to_imx6_pcie(x) dev_get_drvdata((x)->dev) > > > > > > enum imx6_pcie_variants { > > > @@ -37,6 +46,7 @@ enum imx6_pcie_variants { > > > IMX6SX, > > > IMX6QP, > > > IMX7D, > > > + IMX8MQ, > > > }; > > > > > > struct imx6_pcie { > > > @@ -48,8 +58,10 @@ struct imx6_pcie { > > > struct clk *pcie_inbound_axi; > > > struct clk *pcie; > > > struct regmap *iomuxc_gpr; > > > + u32 gpr1x; > > > struct reset_control *pciephy_reset; > > > struct reset_control *apps_reset; > > > + struct reset_control *apps_clk_req; > > > struct reset_control *turnoff_reset; > > > enum imx6_pcie_variants variant; > > > u32 tx_deemph_gen1; > > > @@ -59,6 +71,7 @@ struct imx6_pcie { > > > u32 tx_swing_low; > > > int link_gen; > > > struct regulator *vpcie; > > > + u32 device_type[2]; > > > }; > > > > > > /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */ > > > @@ > > > -245,7 +258,8 @@ static void imx6_pcie_reset_phy(struct imx6_pcie > > > *imx6_pcie) { > > > u32 tmp; > > > > > > - if (imx6_pcie->variant == IMX7D) > > > + if (imx6_pcie->variant == IMX7D || > > > + imx6_pcie->variant == IMX8MQ) > > > return; > > > > > > pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp); @@ > -261,6 > > > +275,7 @@ static void imx6_pcie_reset_phy(struct imx6_pcie > > > +*imx6_pcie) > > > pcie_phy_write(imx6_pcie, PHY_RX_OVRD_IN_LO, tmp); } > > > > > > +#ifdef CONFIG_ARM > > > /* Added for PCI abort handling */ static int > > > imx6q_pcie_abort_handler(unsigned long addr, > > > unsigned int fsr, struct pt_regs *regs) @@ -294,6 > > > +309,7 @@ static int imx6q_pcie_abort_handler(unsigned long addr, > > > > > > return 1; > > > } > > > +#endif > > > > > > static void imx6_pcie_assert_core_reset(struct imx6_pcie > > > *imx6_pcie) { @@ -301,6 +317,7 @@ static void > > > imx6_pcie_assert_core_reset(struct > > > imx6_pcie *imx6_pcie) > > > > > > switch (imx6_pcie->variant) { > > > case IMX7D: > > > + case IMX8MQ: /* FALLTHROUGH */ > > > reset_control_assert(imx6_pcie->pciephy_reset); > > > reset_control_assert(imx6_pcie->apps_reset); > > > break; > > > @@ -369,6 +386,18 @@ static int imx6_pcie_enable_ref_clk(struct > > > imx6_pcie *imx6_pcie) > > > break; > > > case IMX7D: > > > break; > > > + case IMX8MQ: > > > + /* > > > + * Set the over ride low and enabled > > > + * make sure that REF_CLK is turned on. > > > + */ > > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > imx6_pcie->gpr1x, > > > + > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE, > > > + 0); > > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > imx6_pcie->gpr1x, > > > + > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, > > > + > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN); > > > + break; > > > } > > > > > > return ret; > > > @@ -397,6 +426,7 @@ static void imx6_pcie_deassert_core_reset(struct > > > imx6_pcie *imx6_pcie) { > > > struct dw_pcie *pci = imx6_pcie->pci; > > > struct device *dev = pci->dev; > > > + unsigned int val; > > > int ret; > > > > > > if (imx6_pcie->vpcie && > > > !regulator_is_enabled(imx6_pcie->vpcie)) { @@ > > > -445,6 +475,29 @@ static void imx6_pcie_deassert_core_reset(struct > > > imx6_pcie *imx6_pcie) > > > } > > > > > > switch (imx6_pcie->variant) { > > > + case IMX8MQ: > > > + reset_control_deassert(imx6_pcie->pciephy_reset); > > > + udelay(100); > > > + /* > > > + * Configure the CLK_REQ# high, let the L1SS > > > + * automatically controlled by HW. > > > + */ > > > + reset_control_assert(imx6_pcie->apps_clk_req); > > > + > > > + /* > > > + * Configure the L1 latency of rc to less than 64us > > > + * Otherwise, the L1/L1SUB wouldn't be enable by > ASPM. > > > + */ > > > + val = dw_pcie_readl_dbi(imx6_pcie->pci, > > > + SZ_1M + > > > + > IMX8MQ_PCIE_LINK_CAP_REG_OFFSET); > > > + val &= ~PCI_EXP_LNKCAP_L1EL; > > > + val |= IMX8MQ_PCIE_LINK_CAP_L1EL_64US; > > > + dw_pcie_writel_dbi(imx6_pcie->pci, > > > + SZ_1M + > > > + > IMX8MQ_PCIE_LINK_CAP_REG_OFFSET, > > > + val); > > > + break; > > > case IMX7D: > > > reset_control_deassert(imx6_pcie->pciephy_reset); > > > imx7d_pcie_wait_for_phy_pll_lock(imx6_pcie); > > > @@ -483,6 +536,15 @@ static void > > > imx6_pcie_deassert_core_reset(struct > > > imx6_pcie *imx6_pcie) static void imx6_pcie_init_phy(struct > > > imx6_pcie > > > *imx6_pcie) { > > > switch (imx6_pcie->variant) { > > > + case IMX8MQ: > > > + /* > > > + * TODO: Currently this code assumes external > > > + * oscillator is being used > > > + */ > > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > imx6_pcie->gpr1x, > > > + > IMX8MQ_GPR_PCIE_REF_USE_PAD, > > > + > IMX8MQ_GPR_PCIE_REF_USE_PAD); > > > + break; > > > case IMX7D: > > > regmap_update_bits(imx6_pcie->iomuxc_gpr, > IOMUXC_GPR12, > > > > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, > > > 0); @@ > > > -519,7 +581,8 @@ static void imx6_pcie_init_phy(struct imx6_pcie > > > *imx6_pcie) > > > } > > > > > > regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > > > - IMX6Q_GPR12_DEVICE_TYPE, > PCI_EXP_TYPE_ROOT_PORT << > > > 12); > > > + imx6_pcie->device_type[0], > > > + imx6_pcie->device_type[1]); > > > } > > > > > > static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie) @@ > > > -528,7 > > > +591,8 @@ static int imx6_setup_phy_mpll(struct imx6_pcie > > > +*imx6_pcie) > > > int mult, div; > > > u32 val; > > > > > > - if (imx6_pcie->variant == IMX7D) > > > + if (imx6_pcie->variant == IMX7D || > > > + imx6_pcie->variant == IMX8MQ) > > > return 0; > > > > > > switch (phy_rate) { > > > @@ -616,6 +680,7 @@ static void imx6_pcie_ltssm_enable(struct device > > > *dev) > > > IMX6Q_GPR12_PCIE_CTL_2); > > > break; > > > case IMX7D: > > > + case IMX8MQ: /* FALLTHROUGH */ > > > reset_control_deassert(imx6_pcie->apps_reset); > > > break; > > > } > > > @@ -798,10 +863,24 @@ static void imx6_pcie_clk_disable(struct > > > imx6_pcie > > > *imx6_pcie) > > > clk_disable_unprepare(imx6_pcie->pcie_phy); > > > clk_disable_unprepare(imx6_pcie->pcie_bus); > > > > > > - if (imx6_pcie->variant == IMX7D) { > > > + switch (imx6_pcie->variant) { > > > + case IMX7D: > > > regmap_update_bits(imx6_pcie->iomuxc_gpr, > IOMUXC_GPR12, > > > > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, > > > > IMX7D_GPR12_PCIE_PHY_REFCLK_SEL); > > > + break; > > > + /* > > > + * Disable the override. Configure the CLK_REQ# high, let the > > > + * L1SS automatically controlled by HW when link is up. > > > + * Otherwise, turn off the REF_CLK to save power consumption. > > > + */ > > [Richard Zhu] About the L1SS support, there is a back-compatible issue. > > When one none-L1SS capability EP device is used in one HW design solution. > > In this case, EP device wouldn't manipulated its own CLK_REQ#. > > The CLK_REQ# would be high when the override_en is disabled here. > > That means the REFCLK would be turned off abnormally. > > System would have problem when the REFCLK of PCIe is turned off > abnormally after link is up. > > > > I don't have a lot of expertise in this area, so please take my comment with a > grain of salt. The way I understand it, is in legacy systems that do not support > L1SS with CLKREQ that feature shouldn't be enabled/used. Unless I've missed > something, I think it should be possible to do so and disable the feature by > configuring corresponding CLKREQ_B pad as GPIO and adding a GPIO hog > node to pull CLKREQ low. Do you see any problems with this approach? [Richard Zhu]Sorry to reply late. You're right. The L1SS shouldn't be enabled when L1SS none-supported EP device is inserted. The CLKREQ# can be configured as INPUT and OD, I think. But the L1SS capability should be figured out by SW in a proper mechanism. And SW should enable the L1SS automatically refer to the capability. I found the below notice in the L1SS ECN. " 5. Analysis of the Software Implications Capability discovery and enabling are required. " > > Regardless though, I wasn't really planning on including PM support in this > series. The code in question shouldn't even be in the patch since it'll never be > executed because imx6_pcie_clk_disable() is only called by > imx6_pcie_suspend_noirq() which is a no-op on all variants except i.MX7D. > > I'll drop all of the unused PM-related bits I missed from the series and we can > add them later in a separate submission. > [Richard Zhu] Agree with that. The PM feature can be added later in a standalone patch-set. Thanks Richard > Thanks, > Andrey Smirnov ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-17 18:12 ` [PATCH 3/3] PCI: imx: Add support for i.MX8MQ Andrey Smirnov 2018-11-19 7:07 ` Richard Zhu @ 2018-11-20 10:48 ` Leonard Crestez 2018-11-26 18:24 ` Andrey Smirnov 1 sibling, 1 reply; 21+ messages in thread From: Leonard Crestez @ 2018-11-20 10:48 UTC (permalink / raw) To: linux-arm-kernel On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) > - case IMX7D: > + case IMX8MQ: > + if (of_property_read_u32(node, "fsl,iomux-gpr1x", > + &imx6_pcie->gpr1x)) { > + dev_err(dev, "Failed to get GPR1x address\n"); > + return -EINVAL; > + } This is for distinguishing multiple controllers on the SOC but other registers and bits might differ. Isn't it preferable to have a property for controller id instead of adding many registers to DT? > + > + if (of_property_read_u32_array( > + node, "fsl,gpr12-device-type", > + imx6_pcie->device_type, > + ARRAY_SIZE(imx6_pcie->device_type))) { > + dev_err(dev, "Failed to get device type > mask/value\n"); > + return -EINVAL; > + } The device type can be set on multiple SOCs, why are you adding a mandatory property only for 8m? There should probably be a separate patch with documented DT bindings. -- Regards, Leonard ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-20 10:48 ` Leonard Crestez @ 2018-11-26 18:24 ` Andrey Smirnov 2018-11-27 10:06 ` Lucas Stach 2018-11-27 10:16 ` Leonard Crestez 0 siblings, 2 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-26 18:24 UTC (permalink / raw) To: linux-arm-kernel On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > > @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) > > - case IMX7D: > > + case IMX8MQ: > > + if (of_property_read_u32(node, "fsl,iomux-gpr1x", > > + &imx6_pcie->gpr1x)) { > > + dev_err(dev, "Failed to get GPR1x address\n"); > > + return -EINVAL; > > + } > > This is for distinguishing multiple controllers on the SOC but other > registers and bits might differ. Isn't it preferable to have a property > for controller id instead of adding many registers to DT? > I liked encoding necessary info in DT directly slightly better than encoding abstract ID and then decoding it further in the driver code. OTOH, I am not really attached to that path. Lucas, can you comment on this please? > > + > > + if (of_property_read_u32_array( > > + node, "fsl,gpr12-device-type", > > + imx6_pcie->device_type, > > + ARRAY_SIZE(imx6_pcie->device_type))) { > > + dev_err(dev, "Failed to get device type > > mask/value\n"); > > + return -EINVAL; > > + } > > The device type can be set on multiple SOCs, why are you adding a > mandatory property only for 8m? My thinking was that other SoCs don't really have two controllers, so they don't really need to have that property, but, more importantly, not forcing them to have this property should preserve backwards compatibility with old DTBs. > > There should probably be a separate patch with documented DT bindings. > Yes, definitely, I just wanted to come up with a set of bindings agreed on by the driver maintainers first. Thanks, Andrey Smirnov ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-26 18:24 ` Andrey Smirnov @ 2018-11-27 10:06 ` Lucas Stach 2018-11-27 10:46 ` Leonard Crestez 2018-11-27 10:16 ` Leonard Crestez 1 sibling, 1 reply; 21+ messages in thread From: Lucas Stach @ 2018-11-27 10:06 UTC (permalink / raw) To: linux-arm-kernel Hi Andrey, Am Montag, den 26.11.2018, 10:24 -0800 schrieb Andrey Smirnov: > On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > > > On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > > > @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) > > > -?????case IMX7D: > > > +?????case IMX8MQ: > > > +?????????????if (of_property_read_u32(node, "fsl,iomux-gpr1x", > > > +??????????????????????????????????????&imx6_pcie->gpr1x)) { > > > +?????????????????????dev_err(dev, "Failed to get GPR1x address\n"); > > > +?????????????????????return -EINVAL; > > > +?????????????} > > > > This is for distinguishing multiple controllers on the SOC but other > > registers and bits might differ. Isn't it preferable to have a property > > for controller id instead of adding many registers to DT? > > > > I liked encoding necessary info in DT directly slightly better than > encoding abstract ID and then decoding it further in the driver code. > OTOH, I am not really attached to that path. Lucas, can you comment on > this please? Yes, after rereading the patch with this in mind I agree that having the GPR offset on DT directly is IMO the better approach than an abstract ID. One other thing I noticed is that we probably need some property to encode if the clock is supplied by an external clkgen, or if the clock is provided by the i.MX. Hardcoding this in the driver will lead to DT backward compatibility headaches later on if someone decides to build a board with the clock provided from the i.MX. Regards, Lucas ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-27 10:06 ` Lucas Stach @ 2018-11-27 10:46 ` Leonard Crestez 2018-11-27 21:14 ` Andrey Smirnov 0 siblings, 1 reply; 21+ messages in thread From: Leonard Crestez @ 2018-11-27 10:46 UTC (permalink / raw) To: linux-arm-kernel On 11/27/18 12:06 PM, Lucas Stach wrote: > Hi Andrey, > > Am Montag, den 26.11.2018, 10:24 -0800 schrieb Andrey Smirnov: >> On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: >>> >>> On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: >>>> @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) >>>> -?????case IMX7D: >>>> +?????case IMX8MQ: >>>> +?????????????if (of_property_read_u32(node, "fsl,iomux-gpr1x", >>>> +??????????????????????????????????????&imx6_pcie->gpr1x)) { >>>> +?????????????????????dev_err(dev, "Failed to get GPR1x address\n"); >>>> +?????????????????????return -EINVAL; >>>> +?????????????} >>> >>> This is for distinguishing multiple controllers on the SOC but other >>> registers and bits might differ. Isn't it preferable to have a property >>> for controller id instead of adding many registers to DT? >> >> I liked encoding necessary info in DT directly slightly better than >> encoding abstract ID and then decoding it further in the driver code. >> OTOH, I am not really attached to that path. Lucas, can you comment on >> this please? > > Yes, after rereading the patch with this in mind I agree that having > the GPR offset on DT directly is IMO the better approach than an > abstract ID. But it's not a single offset, for example the device_type (EP/RC) has bits for the two controllers side-by-side in GPR12. Adding a "ctrl-id" property would fully describe the hardware from the start. If we add per-register information instead then when other registers are used we'll get DT compatibility headaches. It's worth noting that 8qm/8qxp also have multiple controllers with a different set of bits placed differently in iomuxc. ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-27 10:46 ` Leonard Crestez @ 2018-11-27 21:14 ` Andrey Smirnov 2018-11-28 10:55 ` Leonard Crestez 2018-11-29 11:12 ` Lucas Stach 0 siblings, 2 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-27 21:14 UTC (permalink / raw) To: linux-arm-kernel On Tue, Nov 27, 2018 at 2:46 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > On 11/27/18 12:06 PM, Lucas Stach wrote: > > Hi Andrey, > > > > Am Montag, den 26.11.2018, 10:24 -0800 schrieb Andrey Smirnov: > >> On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > >>> > >>> On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > >>>> @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) > >>>> - case IMX7D: > >>>> + case IMX8MQ: > >>>> + if (of_property_read_u32(node, "fsl,iomux-gpr1x", > >>>> + &imx6_pcie->gpr1x)) { > >>>> + dev_err(dev, "Failed to get GPR1x address\n"); > >>>> + return -EINVAL; > >>>> + } > >>> > >>> This is for distinguishing multiple controllers on the SOC but other > >>> registers and bits might differ. Isn't it preferable to have a property > >>> for controller id instead of adding many registers to DT? > >> > >> I liked encoding necessary info in DT directly slightly better than > >> encoding abstract ID and then decoding it further in the driver code. > >> OTOH, I am not really attached to that path. Lucas, can you comment on > >> this please? > > > > Yes, after rereading the patch with this in mind I agree that having > > the GPR offset on DT directly is IMO the better approach than an > > abstract ID. > > But it's not a single offset, for example the device_type (EP/RC) has > bits for the two controllers side-by-side in GPR12. > Playing devil's advocate for a bit: More specifically, currently the following per-controller bits need to be configured: - Location of the "device type" field within GPR12 - GPR register to use to control PCIn_CLKREQ_B_OVERRIDE_EN and PCIn_CLKREQ_B_OVERRIDE_EN (GPR14 vs GPR16) - Now that Philip spoke against PCIE_CTRL_APPS_CLK_REQ being exposed via reset controller driver, we need to know which SRC register to use to control that bit (SRC_PCIEPHY_RCR vs. SRC_PCIE2_RCR) Thanks, Andrey Smirnov ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-27 21:14 ` Andrey Smirnov @ 2018-11-28 10:55 ` Leonard Crestez 2018-11-29 11:15 ` Lucas Stach 2018-11-29 11:12 ` Lucas Stach 1 sibling, 1 reply; 21+ messages in thread From: Leonard Crestez @ 2018-11-28 10:55 UTC (permalink / raw) To: linux-arm-kernel On 11/27/18 11:15 PM, Andrey Smirnov wrote: > On Tue, Nov 27, 2018 at 2:46 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: >> On 11/27/18 12:06 PM, Lucas Stach wrote: >>> Am Montag, den 26.11.2018, 10:24 -0800 schrieb Andrey Smirnov: >>>> On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: >>>>> On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: >>>>>> @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) >>>>>> - case IMX7D: >>>>>> + case IMX8MQ: >>>>>> + if (of_property_read_u32(node, "fsl,iomux-gpr1x", >>>>>> + &imx6_pcie->gpr1x)) { >>>>>> + dev_err(dev, "Failed to get GPR1x address\n"); >>>>>> + return -EINVAL; >>>>>> + } >>>>> >>>>> This is for distinguishing multiple controllers on the SOC but other >>>>> registers and bits might differ. Isn't it preferable to have a property >>>>> for controller id instead of adding many registers to DT? >>>> >>>> I liked encoding necessary info in DT directly slightly better than >>>> encoding abstract ID and then decoding it further in the driver code. >>>> OTOH, I am not really attached to that path. Lucas, can you comment on >>>> this please? >>> Yes, after rereading the patch with this in mind I agree that having >>> the GPR offset on DT directly is IMO the better approach than an >>> abstract ID. >> >> But it's not a single offset, for example the device_type (EP/RC) has >> bits for the two controllers side-by-side in GPR12. >> > > Playing devil's advocate for a bit: > > More specifically, currently the following per-controller bits need to > be configured: > > - Location of the "device type" field within GPR12 > - GPR register to use to control PCIn_CLKREQ_B_OVERRIDE_EN and > PCIn_CLKREQ_B_OVERRIDE_EN (GPR14 vs GPR16) > - Now that Philip spoke against PCIE_CTRL_APPS_CLK_REQ being exposed > via reset controller driver, we need to know which SRC register to use > to control that bit (SRC_PCIEPHY_RCR vs. SRC_PCIE2_RCR) I looked a bit through bindings and there some instances of syscon-$BLH properties which include detailed offsets or bitmasks for $BLAH relative to the target syscon node. If you're going the route of adding properties points to IOMUXC/SRC bits it would sense to ensure that they're also usable on other SOCs, otherwise you're just making 8mq more complicated. But that's hard. But I think it's easier to deal with such SOC-specific details behind a compat string. Maybe the DT list has some opinion on this? I wonder if of_alias_get_id would be a reasonable way to distinguish between pcie0 and pcie1 instead of adding an ctrl-id property? -- Regards, Leonard ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-28 10:55 ` Leonard Crestez @ 2018-11-29 11:15 ` Lucas Stach 0 siblings, 0 replies; 21+ messages in thread From: Lucas Stach @ 2018-11-29 11:15 UTC (permalink / raw) To: linux-arm-kernel Am Mittwoch, den 28.11.2018, 10:55 +0000 schrieb Leonard Crestez: > On 11/27/18 11:15 PM, Andrey Smirnov wrote: > > On Tue, Nov 27, 2018 at 2:46 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > > On 11/27/18 12:06 PM, Lucas Stach wrote: > > > > Am Montag, den 26.11.2018, 10:24 -0800 schrieb Andrey Smirnov: > > > > > On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > > > > > On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > > > > > > > @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) > > > > > > > -?????case IMX7D: > > > > > > > +?????case IMX8MQ: > > > > > > > +?????????????if (of_property_read_u32(node, "fsl,iomux-gpr1x", > > > > > > > +??????????????????????????????????????&imx6_pcie->gpr1x)) { > > > > > > > +?????????????????????dev_err(dev, "Failed to get GPR1x address\n"); > > > > > > > +?????????????????????return -EINVAL; > > > > > > > +?????????????} > > > > > > > > > > > > This is for distinguishing multiple controllers on the SOC but other > > > > > > registers and bits might differ. Isn't it preferable to have a property > > > > > > for controller id instead of adding many registers to DT? > > > > > > > > > > I liked encoding necessary info in DT directly slightly better than > > > > > encoding abstract ID and then decoding it further in the driver code. > > > > > OTOH, I am not really attached to that path. Lucas, can you comment on > > > > > this please? > > > > Yes, after rereading the patch with this in mind I agree that having > > > > the GPR offset on DT directly is IMO the better approach than an > > > > abstract ID. > > > > > > But it's not a single offset, for example the device_type (EP/RC) has > > > bits for the two controllers side-by-side in GPR12. > > > > > > > Playing devil's advocate for a bit: > > > > More specifically, currently the following per-controller bits need to > > be configured: > > > > - Location of the "device type" field within GPR12 > > - GPR register to use to control PCIn_CLKREQ_B_OVERRIDE_EN and > > PCIn_CLKREQ_B_OVERRIDE_EN (GPR14 vs GPR16) > > - Now that Philip spoke against PCIE_CTRL_APPS_CLK_REQ being exposed > > via reset controller driver, we need to know which SRC register to use > > to control that bit (SRC_PCIEPHY_RCR vs. SRC_PCIE2_RCR) > > I looked a bit through bindings and there some instances of syscon-$BLH? > properties which include detailed offsets or bitmasks for $BLAH relative? > to the target syscon node. > > If you're going the route of adding properties points to IOMUXC/SRC bits? > it would sense to ensure that they're also usable on other SOCs,? > otherwise you're just making 8mq more complicated. But that's hard. > > But I think it's easier to deal with such SOC-specific details behind a? > compat string. Maybe the DT list has some opinion on this? I agree with this. The number of bits and offsets is too large to keep it in DT properties, without running into backwards compat issues later on. > I wonder if of_alias_get_id would be a reasonable way to distinguish? > between pcie0 and pcie1 instead of adding an ctrl-id property? No, the alias is a arbitrary number that can change from board to board. It can, but doesn't need to, correspond to any real hardware ID. If we need a hardware controller ID, then there is no way around adding a property to the PCIe controller node for this. Regards, Lucas ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-27 21:14 ` Andrey Smirnov 2018-11-28 10:55 ` Leonard Crestez @ 2018-11-29 11:12 ` Lucas Stach 1 sibling, 0 replies; 21+ messages in thread From: Lucas Stach @ 2018-11-29 11:12 UTC (permalink / raw) To: linux-arm-kernel Am Dienstag, den 27.11.2018, 13:14 -0800 schrieb Andrey Smirnov: > On Tue, Nov 27, 2018 at 2:46 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > > > On 11/27/18 12:06 PM, Lucas Stach wrote: > > > Hi Andrey, > > > > > > Am Montag, den 26.11.2018, 10:24 -0800 schrieb Andrey Smirnov: > > > > On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > > > > > > > > > On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > > > > > > @@ -921,7 +1004,28 @@ static int imx6_pcie_probe(struct platform_device *pdev) > > > > > > -?????case IMX7D: > > > > > > +?????case IMX8MQ: > > > > > > +?????????????if (of_property_read_u32(node, "fsl,iomux-gpr1x", > > > > > > +??????????????????????????????????????&imx6_pcie->gpr1x)) { > > > > > > +?????????????????????dev_err(dev, "Failed to get GPR1x address\n"); > > > > > > +?????????????????????return -EINVAL; > > > > > > +?????????????} > > > > > > > > > > This is for distinguishing multiple controllers on the SOC but other > > > > > registers and bits might differ. Isn't it preferable to have a property > > > > > for controller id instead of adding many registers to DT? > > > > > > > > I liked encoding necessary info in DT directly slightly better than > > > > encoding abstract ID and then decoding it further in the driver code. > > > > OTOH, I am not really attached to that path. Lucas, can you comment on > > > > this please? > > > > > > Yes, after rereading the patch with this in mind I agree that having > > > the GPR offset on DT directly is IMO the better approach than an > > > abstract ID. > > > > But it's not a single offset, for example the device_type (EP/RC) has > > bits for the two controllers side-by-side in GPR12. > > > > Playing devil's advocate for a bit: > > More specifically, currently the following per-controller bits need to > be configured: > > - Location of the "device type" field within GPR12 > - GPR register to use to control PCIn_CLKREQ_B_OVERRIDE_EN and > PCIn_CLKREQ_B_OVERRIDE_EN (GPR14 vs GPR16) > - Now that Philip spoke against PCIE_CTRL_APPS_CLK_REQ being exposed > via reset controller driver, we need to know which SRC register to use > to control that bit (SRC_PCIEPHY_RCR vs. SRC_PCIE2_RCR) If if we need a lot of different GPR offsets, I revise my earlier opinion. We certainly don't want lots of bit offsets and masks in the DT. The whole GPR thing is ugly, but I would rather hide this in the driver code, keyed by compatible and a controller id property, where we can change things without any worries about DT backward compatibility. Regards, Lucas ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-26 18:24 ` Andrey Smirnov 2018-11-27 10:06 ` Lucas Stach @ 2018-11-27 10:16 ` Leonard Crestez 2018-11-27 21:03 ` Andrey Smirnov 1 sibling, 1 reply; 21+ messages in thread From: Leonard Crestez @ 2018-11-27 10:16 UTC (permalink / raw) To: linux-arm-kernel On 11/26/18 8:24 PM, Andrey Smirnov wrote: > On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: >> On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: >>> + if (of_property_read_u32_array( >>> + node, "fsl,gpr12-device-type", >>> + imx6_pcie->device_type, >>> + ARRAY_SIZE(imx6_pcie->device_type))) { >>> + dev_err(dev, "Failed to get device type >>> mask/value\n"); >>> + return -EINVAL; >>> + } >> >> The device type can be set on multiple SOCs, why are you adding a >> mandatory property only for 8m? > > My thinking was that other SoCs don't really have two controllers, so > they don't really need to have that property, but, more importantly, > not forcing them to have this property should preserve backwards > compatibility with old DTBs. The "device_type" registers determine Root Complex versus End Point mode. This is not yet supported on imx in upstream but it can be done on many soc versions. Looking at other pcie controllers (and dwc core) this is normally done with a different compatible string with an "-ep" suffix. It feels wrong to expose bitmasks and values directly in DT instead. For this patch you should probably just hardcode RC mode. ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 3/3] PCI: imx: Add support for i.MX8MQ 2018-11-27 10:16 ` Leonard Crestez @ 2018-11-27 21:03 ` Andrey Smirnov 0 siblings, 0 replies; 21+ messages in thread From: Andrey Smirnov @ 2018-11-27 21:03 UTC (permalink / raw) To: linux-arm-kernel On Tue, Nov 27, 2018 at 2:16 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > > On 11/26/18 8:24 PM, Andrey Smirnov wrote: > > On Tue, Nov 20, 2018 at 2:49 AM Leonard Crestez <leonard.crestez@nxp.com> wrote: > >> On Sat, 2018-11-17 at 10:12 -0800, Andrey Smirnov wrote: > > >>> + if (of_property_read_u32_array( > >>> + node, "fsl,gpr12-device-type", > >>> + imx6_pcie->device_type, > >>> + ARRAY_SIZE(imx6_pcie->device_type))) { > >>> + dev_err(dev, "Failed to get device type > >>> mask/value\n"); > >>> + return -EINVAL; > >>> + } > >> > >> The device type can be set on multiple SOCs, why are you adding a > >> mandatory property only for 8m? > > > > My thinking was that other SoCs don't really have two controllers, so > > they don't really need to have that property, but, more importantly, > > not forcing them to have this property should preserve backwards > > compatibility with old DTBs. > > The "device_type" registers determine Root Complex versus End Point > mode. This is not yet supported on imx in upstream but it can be done on > many soc versions. > Yeah, I am aware, I wasn't really trying to make it possible to configure IP block to be a EP, that is just an unavoidable consequence of the approach taken. > Looking at other pcie controllers (and dwc core) this is normally done > with a different compatible string with an "-ep" suffix. It feels wrong > to expose bitmasks and values directly in DT instead. > > For this patch you should probably just hardcode RC mode. Hmm, given how the mask/value have to be different for each controller, the only way to hardcode it that I can think of would be to change the property pass a bit offset instead of mask/value pair. Is that what you are suggesting? Thanks, Andrey Smirnov ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 0/3] PCIE support for i.MX8MQ 2018-11-17 18:12 [PATCH 0/3] PCIE support for i.MX8MQ Andrey Smirnov ` (2 preceding siblings ...) 2018-11-17 18:12 ` [PATCH 3/3] PCI: imx: Add support for i.MX8MQ Andrey Smirnov @ 2018-12-03 12:20 ` Lorenzo Pieralisi 2018-12-07 11:37 ` Lorenzo Pieralisi 4 siblings, 0 replies; 21+ messages in thread From: Lorenzo Pieralisi @ 2018-12-03 12:20 UTC (permalink / raw) To: Andrey Smirnov Cc: A.s. Dong, Richard Zhu, linux-arm-kernel, linux-pci, linux-kernel, Fabio Estevam, linux-imx, bhelgaas, Leonard Crestez, cphealy, l.stach On Sat, Nov 17, 2018 at 10:12:22AM -0800, Andrey Smirnov wrote: > > Everyone: > > This series contains changes I made in order to enable support of PCIE > IP block on i.MX8MQ SoCs (full tree can be found at [github-v0]). This series > is _very_ preliminary and by no means is ready for inclusion (it also > has some unmet dependencies). However is should be in OK enough shape > to get some early feedback on, which is the intent of this submission. > > Specifically, I'd like to get some feedback on whether newly > introduced "fsl,iomux-gpr1x" and "fsl,gpr12-device-type" DT > properties, added to handle differences between PCIE0 and PCIE1, is a > good (acceptable) solution for the problem. > > All other feedback is appreciated as well! > > Thank you, > Andrey Smirnov > > [github-v0] https://github.com/ndreys/linux/commits/imx8mq-pcie-v0 > > Andrey Smirnov (3): > PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D > PCI: imx: No-op imx6_pcie_reset_phy() on i.MX7D > PCI: imx: Add support for i.MX8MQ > > drivers/pci/controller/dwc/Kconfig | 2 +- > drivers/pci/controller/dwc/pci-imx6.c | 119 +++++++++++++++++++++++++- > 2 files changed, 117 insertions(+), 4 deletions(-) I am expecting you to post of v2 of this series, addressing review comments so I will mark these patches with "Changes Requested", please let me know if you have any objections. Lorenzo _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 0/3] PCIE support for i.MX8MQ 2018-11-17 18:12 [PATCH 0/3] PCIE support for i.MX8MQ Andrey Smirnov ` (3 preceding siblings ...) 2018-12-03 12:20 ` [PATCH 0/3] PCIE " Lorenzo Pieralisi @ 2018-12-07 11:37 ` Lorenzo Pieralisi 4 siblings, 0 replies; 21+ messages in thread From: Lorenzo Pieralisi @ 2018-12-07 11:37 UTC (permalink / raw) To: Andrey Smirnov Cc: A.s. Dong, Richard Zhu, linux-arm-kernel, linux-pci, linux-kernel, Fabio Estevam, linux-imx, bhelgaas, Leonard Crestez, cphealy, l.stach On Sat, Nov 17, 2018 at 10:12:22AM -0800, Andrey Smirnov wrote: > > Everyone: > > This series contains changes I made in order to enable support of PCIE > IP block on i.MX8MQ SoCs (full tree can be found at [github-v0]). This series > is _very_ preliminary and by no means is ready for inclusion (it also > has some unmet dependencies). However is should be in OK enough shape > to get some early feedback on, which is the intent of this submission. > > Specifically, I'd like to get some feedback on whether newly > introduced "fsl,iomux-gpr1x" and "fsl,gpr12-device-type" DT > properties, added to handle differences between PCIE0 and PCIE1, is a > good (acceptable) solution for the problem. > > All other feedback is appreciated as well! > > Thank you, > Andrey Smirnov > > [github-v0] https://github.com/ndreys/linux/commits/imx8mq-pcie-v0 > > Andrey Smirnov (3): > PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D > PCI: imx: No-op imx6_pcie_reset_phy() on i.MX7D > PCI: imx: Add support for i.MX8MQ > > drivers/pci/controller/dwc/Kconfig | 2 +- > drivers/pci/controller/dwc/pci-imx6.c | 119 +++++++++++++++++++++++++- > 2 files changed, 117 insertions(+), 4 deletions(-) Applied to pci/dwc for v4.21, thanks. Lorenzo _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
end of thread, other threads:[~2018-12-07 11:37 UTC | newest] Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2018-11-17 18:12 [PATCH 0/3] PCIE support for i.MX8MQ Andrey Smirnov 2018-11-17 18:12 ` [PATCH 1/3] PCI: imx: No-op imx6_setup_phy_mpll() on i.MX7D Andrey Smirnov 2018-11-17 18:12 ` [PATCH 2/3] PCI: imx: No-op imx6_pcie_reset_phy() " Andrey Smirnov 2018-11-20 1:22 ` Trent Piepho 2018-11-26 18:32 ` Andrey Smirnov 2018-11-17 18:12 ` [PATCH 3/3] PCI: imx: Add support for i.MX8MQ Andrey Smirnov 2018-11-19 7:07 ` Richard Zhu 2018-11-26 18:09 ` Andrey Smirnov 2018-11-29 10:52 ` Richard Zhu 2018-11-20 10:48 ` Leonard Crestez 2018-11-26 18:24 ` Andrey Smirnov 2018-11-27 10:06 ` Lucas Stach 2018-11-27 10:46 ` Leonard Crestez 2018-11-27 21:14 ` Andrey Smirnov 2018-11-28 10:55 ` Leonard Crestez 2018-11-29 11:15 ` Lucas Stach 2018-11-29 11:12 ` Lucas Stach 2018-11-27 10:16 ` Leonard Crestez 2018-11-27 21:03 ` Andrey Smirnov 2018-12-03 12:20 ` [PATCH 0/3] PCIE " Lorenzo Pieralisi 2018-12-07 11:37 ` Lorenzo Pieralisi
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).