From: Pratyush Yadav <p.yadav@ti.com>
To: Tudor Ambarus <tudor.ambarus@microchip.com>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
<linux-mtd@lists.infradead.org>, <linux-kernel@vger.kernel.org>
Cc: Boris Brezillon <boris.brezillon@collabora.com>,
Sekhar Nori <nsekhar@ti.com>, Pratyush Yadav <p.yadav@ti.com>
Subject: [PATCH v13 10/15] mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT
Date: Wed, 16 Sep 2020 18:14:13 +0530 [thread overview]
Message-ID: <20200916124418.833-11-p.yadav@ti.com> (raw)
In-Reply-To: <20200916124418.833-1-p.yadav@ti.com>
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
drivers/mtd/spi-nor/core.h | 1 +
drivers/mtd/spi-nor/sfdp.c | 4 ++++
drivers/mtd/spi-nor/sfdp.h | 2 ++
3 files changed, 7 insertions(+)
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index fcb5f071ebed..e2c7324d997e 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -26,6 +26,7 @@ enum spi_nor_option_flags {
SNOR_F_HAS_SR_TB_BIT6 = BIT(11),
SNOR_F_HAS_4BIT_BP = BIT(12),
SNOR_F_HAS_SR_BP3_BIT6 = BIT(13),
+ SNOR_F_SOFT_RESET = BIT(14),
};
struct spi_nor_read_command {
diff --git a/drivers/mtd/spi-nor/sfdp.c b/drivers/mtd/spi-nor/sfdp.c
index cadb1ed27ffe..f192710aca31 100644
--- a/drivers/mtd/spi-nor/sfdp.c
+++ b/drivers/mtd/spi-nor/sfdp.c
@@ -604,6 +604,10 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
break;
}
+ /* Soft Reset support. */
+ if (bfpt.dwords[BFPT_DWORD(16)] & BFPT_DWORD16_SOFT_RST)
+ nor->flags |= SNOR_F_SOFT_RESET;
+
/* Stop here if not JESD216 rev C or later. */
if (bfpt_header->length == BFPT_DWORD_MAX_JESD216B)
return spi_nor_post_bfpt_fixups(nor, bfpt_header, &bfpt,
diff --git a/drivers/mtd/spi-nor/sfdp.h b/drivers/mtd/spi-nor/sfdp.h
index 6d7243067252..8ae55e98084e 100644
--- a/drivers/mtd/spi-nor/sfdp.h
+++ b/drivers/mtd/spi-nor/sfdp.h
@@ -90,6 +90,8 @@ struct sfdp_bfpt {
#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD (0x4UL << 20)
#define BFPT_DWORD15_QER_SR2_BIT1 (0x5UL << 20) /* Spansion */
+#define BFPT_DWORD16_SOFT_RST BIT(12)
+
#define BFPT_DWORD18_CMD_EXT_MASK GENMASK(30, 29)
#define BFPT_DWORD18_CMD_EXT_REP (0x0UL << 29) /* Repeat */
#define BFPT_DWORD18_CMD_EXT_INV (0x1UL << 29) /* Invert */
--
2.28.0
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2020-09-16 12:46 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-16 12:44 [PATCH v13 00/15] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 01/15] mtd: spi-nor: core: use EOPNOTSUPP instead of ENOTSUPP Pratyush Yadav
2020-09-29 11:30 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 02/15] mtd: spi-nor: core: add spi_nor_{read, write}_reg() helpers Pratyush Yadav
2020-09-29 11:38 ` [PATCH v13 02/15] mtd: spi-nor: core: add spi_nor_{read,write}_reg() helpers Tudor.Ambarus
2020-09-29 12:54 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 03/15] mtd: spi-nor: core: add spi_nor_controller_ops_erase helper Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 04/15] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 05/15] mtd: spi-nor: sfdp: get command opcode extension type from BFPT Pratyush Yadav
2020-09-30 6:17 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 06/15] mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table Pratyush Yadav
2020-09-30 6:44 ` Tudor.Ambarus
2020-09-30 6:53 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 07/15] mtd: spi-nor: core: use dummy cycle and address width info from SFDP Pratyush Yadav
2020-09-30 6:46 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 08/15] mtd: spi-nor: core: do 2 byte reads for SR and FSR in DTR mode Pratyush Yadav
2020-09-30 6:50 ` Tudor.Ambarus
2020-09-30 6:55 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 09/15] mtd: spi-nor: core: enable octal DTR mode when possible Pratyush Yadav
2020-09-29 11:26 ` Tudor.Ambarus
2020-09-29 12:51 ` Pratyush Yadav
2020-09-29 13:05 ` Tudor.Ambarus
2020-09-30 7:11 ` Tudor.Ambarus
2020-09-16 12:44 ` Pratyush Yadav [this message]
2020-09-30 7:23 ` [PATCH v13 10/15] mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT Tudor.Ambarus
2020-09-30 7:31 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 11/15] mtd: spi-nor: core: perform a Soft Reset on shutdown Pratyush Yadav
2020-09-29 13:08 ` Pratyush Yadav
2020-09-30 7:32 ` Tudor.Ambarus
2020-09-30 7:43 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 12/15] mtd: spi-nor: core: disable Octal DTR mode on suspend Pratyush Yadav
2020-09-30 7:40 ` Tudor.Ambarus
2020-09-30 7:44 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 13/15] mtd: spi-nor: core: expose spi_nor_default_setup() in core.h Pratyush Yadav
2020-09-30 7:51 ` Tudor.Ambarus
2020-09-30 8:03 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 14/15] mtd: spi-nor: spansion: add support for Cypress Semper flash Pratyush Yadav
2020-09-30 8:36 ` Tudor.Ambarus
2020-09-30 12:32 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 15/15] mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode Pratyush Yadav
2020-09-30 9:12 ` Tudor.Ambarus
2020-09-29 9:59 ` [RFC PATCH 0/3] mtd: spi-nor: Tackle stateful modes Tudor Ambarus
2020-09-29 9:59 ` [RFC PATCH 1/3] mtd: spi-nor: Introduce SNOR_F_IO_MODE_EN_VOLATILE Tudor Ambarus
2020-09-29 16:45 ` Vignesh Raghavendra
2020-09-29 9:59 ` [RFC PATCH 2/3] mtd: spi-nor: Introduce MTD_SPI_NOR_ALLOW_STATEFUL_MODES Tudor Ambarus
2020-09-29 16:45 ` Vignesh Raghavendra
2020-09-29 9:59 ` [RFC PATCH 3/3] mtd: spi-nor: Parse SFDP SCCR Map Tudor Ambarus
2020-09-30 9:57 ` [PATCH v13 00/15] mtd: spi-nor: add xSPI Octal DTR support Tudor.Ambarus
2020-09-30 12:01 ` Pratyush Yadav
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200916124418.833-11-p.yadav@ti.com \
--to=p.yadav@ti.com \
--cc=boris.brezillon@collabora.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=nsekhar@ti.com \
--cc=richard@nod.at \
--cc=tudor.ambarus@microchip.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).