From: <Tudor.Ambarus@microchip.com>
To: <p.yadav@ti.com>, <miquel.raynal@bootlin.com>, <richard@nod.at>,
<vigneshr@ti.com>, <linux-mtd@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Cc: boris.brezillon@collabora.com, nsekhar@ti.com
Subject: Re: [PATCH v13 15/15] mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode
Date: Wed, 30 Sep 2020 09:12:17 +0000 [thread overview]
Message-ID: <62ad761a-3fcf-07c2-0b3d-0a27d877dcde@microchip.com> (raw)
In-Reply-To: <20200916124418.833-16-p.yadav@ti.com>
On 9/16/20 3:44 PM, Pratyush Yadav wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>
> Since this flash doesn't have a Profile 1.0 table, the Octal DTR
> capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
> fast read settings.
>
> Enable Octal DTR mode with 20 dummy cycles to allow running at the
> maximum supported frequency of 200Mhz.
>
> The flash supports the soft reset sequence. So, add the flag in the
> flash's info.
>
> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> ---
> drivers/mtd/spi-nor/micron-st.c | 102 +++++++++++++++++++++++++++++++-
> 1 file changed, 101 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/mtd/spi-nor/micron-st.c b/drivers/mtd/spi-nor/micron-st.c
> index ef3695080710..cc02c1418d1d 100644
> --- a/drivers/mtd/spi-nor/micron-st.c
> +++ b/drivers/mtd/spi-nor/micron-st.c
> @@ -8,10 +8,110 @@
similar comments to those in 14/15 apply here as well.
Looks good. I couldn't find datasheets for neither of flashes though.
Cheers,
ta
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2020-09-30 9:13 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-16 12:44 [PATCH v13 00/15] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 01/15] mtd: spi-nor: core: use EOPNOTSUPP instead of ENOTSUPP Pratyush Yadav
2020-09-29 11:30 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 02/15] mtd: spi-nor: core: add spi_nor_{read, write}_reg() helpers Pratyush Yadav
2020-09-29 11:38 ` [PATCH v13 02/15] mtd: spi-nor: core: add spi_nor_{read,write}_reg() helpers Tudor.Ambarus
2020-09-29 12:54 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 03/15] mtd: spi-nor: core: add spi_nor_controller_ops_erase helper Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 04/15] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 05/15] mtd: spi-nor: sfdp: get command opcode extension type from BFPT Pratyush Yadav
2020-09-30 6:17 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 06/15] mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table Pratyush Yadav
2020-09-30 6:44 ` Tudor.Ambarus
2020-09-30 6:53 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 07/15] mtd: spi-nor: core: use dummy cycle and address width info from SFDP Pratyush Yadav
2020-09-30 6:46 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 08/15] mtd: spi-nor: core: do 2 byte reads for SR and FSR in DTR mode Pratyush Yadav
2020-09-30 6:50 ` Tudor.Ambarus
2020-09-30 6:55 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 09/15] mtd: spi-nor: core: enable octal DTR mode when possible Pratyush Yadav
2020-09-29 11:26 ` Tudor.Ambarus
2020-09-29 12:51 ` Pratyush Yadav
2020-09-29 13:05 ` Tudor.Ambarus
2020-09-30 7:11 ` Tudor.Ambarus
2020-09-16 12:44 ` [PATCH v13 10/15] mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT Pratyush Yadav
2020-09-30 7:23 ` Tudor.Ambarus
2020-09-30 7:31 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 11/15] mtd: spi-nor: core: perform a Soft Reset on shutdown Pratyush Yadav
2020-09-29 13:08 ` Pratyush Yadav
2020-09-30 7:32 ` Tudor.Ambarus
2020-09-30 7:43 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 12/15] mtd: spi-nor: core: disable Octal DTR mode on suspend Pratyush Yadav
2020-09-30 7:40 ` Tudor.Ambarus
2020-09-30 7:44 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 13/15] mtd: spi-nor: core: expose spi_nor_default_setup() in core.h Pratyush Yadav
2020-09-30 7:51 ` Tudor.Ambarus
2020-09-30 8:03 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 14/15] mtd: spi-nor: spansion: add support for Cypress Semper flash Pratyush Yadav
2020-09-30 8:36 ` Tudor.Ambarus
2020-09-30 12:32 ` Pratyush Yadav
2020-09-16 12:44 ` [PATCH v13 15/15] mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode Pratyush Yadav
2020-09-30 9:12 ` Tudor.Ambarus [this message]
2020-09-29 9:59 ` [RFC PATCH 0/3] mtd: spi-nor: Tackle stateful modes Tudor Ambarus
2020-09-29 9:59 ` [RFC PATCH 1/3] mtd: spi-nor: Introduce SNOR_F_IO_MODE_EN_VOLATILE Tudor Ambarus
2020-09-29 16:45 ` Vignesh Raghavendra
2020-09-29 9:59 ` [RFC PATCH 2/3] mtd: spi-nor: Introduce MTD_SPI_NOR_ALLOW_STATEFUL_MODES Tudor Ambarus
2020-09-29 16:45 ` Vignesh Raghavendra
2020-09-29 9:59 ` [RFC PATCH 3/3] mtd: spi-nor: Parse SFDP SCCR Map Tudor Ambarus
2020-09-30 9:57 ` [PATCH v13 00/15] mtd: spi-nor: add xSPI Octal DTR support Tudor.Ambarus
2020-09-30 12:01 ` Pratyush Yadav
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=62ad761a-3fcf-07c2-0b3d-0a27d877dcde@microchip.com \
--to=tudor.ambarus@microchip.com \
--cc=boris.brezillon@collabora.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=nsekhar@ti.com \
--cc=p.yadav@ti.com \
--cc=richard@nod.at \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).