Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
From: Serge Semin <Sergey.Semin@baikalelectronics.ru>
To: Mark Brown <broonie@kernel.org>, Serge Semin <fancer.lancer@gmail.com>
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>,
	Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>,
	Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>,
	Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>,
	Andy Shevchenko <andy.shevchenko@gmail.com>,
	Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
	Lars Povlsen <lars.povlsen@microchip.com>,
	"wuxu . wu" <wuxu.wu@huawei.com>, Feng Tang <feng.tang@intel.com>,
	Rob Herring <robh+dt@kernel.org>, <linux-spi@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v4 11/21] spi: dw: Unmask IRQs after enabling the chip
Date: Thu, 8 Oct 2020 02:55:00 +0300
Message-ID: <20201007235511.4935-12-Sergey.Semin@baikalelectronics.ru> (raw)
In-Reply-To: <20201007235511.4935-1-Sergey.Semin@baikalelectronics.ru>

It's theoretically erroneous to enable IRQ before the chip is turned on.
If IRQ handler gets executed before the chip is enabled, then any data
written to the Tx FIFO will be just ignored.

I say "theoretically" because we haven't noticed any problem with that,
but let's fix it anyway just in case...

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
---
 drivers/spi/spi-dw-core.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-dw-core.c b/drivers/spi/spi-dw-core.c
index e7ffcfff6594..89e5428c8de6 100644
--- a/drivers/spi/spi-dw-core.c
+++ b/drivers/spi/spi-dw-core.c
@@ -376,8 +376,6 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 			spi_enable_chip(dws, 1);
 			return ret;
 		}
-	} else {
-		dw_spi_irq_setup(dws);
 	}
 
 	spi_enable_chip(dws, 1);
@@ -385,6 +383,8 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 	if (dws->dma_mapped)
 		return dws->dma_ops->dma_transfer(dws, transfer);
 
+	dw_spi_irq_setup(dws);
+
 	return 1;
 }
 
-- 
2.27.0


  parent reply index

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-10-07 23:54 [PATCH v4 00/21] spi: dw: Add full Baikal-T1 SPI Controllers support Serge Semin
2020-10-07 23:54 ` [PATCH v4 01/21] spi: dw: Use an explicit set_cs assignment Serge Semin
2020-10-07 23:54 ` [PATCH v4 02/21] spi: dw: Add DWC SSI capability Serge Semin
2020-10-07 23:54 ` [PATCH v4 03/21] spi: dw: Detach SPI device specific CR0 config method Serge Semin
2020-10-07 23:54 ` [PATCH v4 04/21] spi: dw: Update SPI bus speed in a config function Serge Semin
2020-10-07 23:54 ` [PATCH v4 05/21] spi: dw: Simplify the SPI bus speed config procedure Serge Semin
2020-10-07 23:54 ` [PATCH v4 06/21] spi: dw: Update Rx sample delay in the config function Serge Semin
2020-10-07 23:54 ` [PATCH v4 07/21] spi: dw: Add DW SPI controller config structure Serge Semin
2020-10-07 23:54 ` [PATCH v4 08/21] spi: dw: Refactor data IO procedure Serge Semin
2020-10-07 23:54 ` [PATCH v4 09/21] spi: dw: Refactor IRQ-based SPI transfer procedure Serge Semin
2020-10-07 23:54 ` [PATCH v4 10/21] spi: dw: Perform IRQ setup in a dedicated function Serge Semin
2020-10-07 23:55 ` Serge Semin [this message]
2020-10-07 23:55 ` [PATCH v4 12/21] spi: dw: Discard chip enabling on DMA setup error Serge Semin
2020-10-07 23:55 ` [PATCH v4 13/21] spi: dw: De-assert chip-select on reset Serge Semin
2020-10-07 23:55 ` [PATCH v4 14/21] spi: dw: Explicitly de-assert CS on SPI transfer completion Serge Semin
2020-10-07 23:55 ` [PATCH v4 15/21] spi: dw: Move num-of retries parameter to the header file Serge Semin
2020-10-07 23:55 ` [PATCH v4 16/21] spi: dw: Add generic DW SSI status-check method Serge Semin
2020-10-07 23:55 ` [PATCH v4 17/21] spi: dw: Add memory operations support Serge Semin
2020-10-07 23:55 ` [PATCH v4 18/21] spi: dw: Introduce max mem-ops SPI bus frequency setting Serge Semin
2020-10-07 23:55 ` [PATCH v4 19/21] spi: dw: Add poll-based SPI transfers support Serge Semin
2020-10-07 23:55 ` [PATCH v4 20/21] dt-bindings: spi: dw: Add Baikal-T1 SPI Controllers Serge Semin
2020-10-07 23:55 ` [PATCH v4 21/21] spi: dw: Add Baikal-T1 SPI Controller glue driver Serge Semin
2020-10-08 22:02 ` [PATCH v4 00/21] spi: dw: Add full Baikal-T1 SPI Controllers support Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201007235511.4935-12-Sergey.Semin@baikalelectronics.ru \
    --to=sergey.semin@baikalelectronics.ru \
    --cc=Alexey.Malahov@baikalelectronics.ru \
    --cc=Pavel.Parkhomenko@baikalelectronics.ru \
    --cc=Ramil.Zaripov@baikalelectronics.ru \
    --cc=andriy.shevchenko@linux.intel.com \
    --cc=andy.shevchenko@gmail.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=fancer.lancer@gmail.com \
    --cc=feng.tang@intel.com \
    --cc=lars.povlsen@microchip.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=wuxu.wu@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git