[PATCH v3 1/8] dt-bindings: mfd: document stpmic1

[Pascal PAILLET-LME <p.paillet@st.com>]

From: pascal paillet <p.paillet@st.com>

stpmic1 is a pmic from STMicroelectronics. The STPMIC1 integrates 10
regulators ,3 switches, a watchdog and an input for a power on key.

Signed-off-by: pascal paillet <p.paillet@st.com>
---
changes in v3:
* Replace st,onkey-long-press-seconds by power-off-time-sec.
* Replace interrupts-extended by  interrupts.
* Remove wakeup interrupt.
* Cosmetics.

 .../devicetree/bindings/mfd/st,stpmic1.txt         | 133 +++++++++++++++++++++
 include/dt-bindings/mfd/st,stpmic1.h               |  46 +++++++
 2 files changed, 179 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmic1.txt
 create mode 100644 include/dt-bindings/mfd/st,stpmic1.h

diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
new file mode 100644
index 0000000..989bd58
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
@@ -0,0 +1,133 @@
+* STMicroelectronics STPMIC1 Power Management IC
+
+Required parent device properties:
+- compatible: 		"st,stpmic1"
+- reg: 			The I2C slave address for the STPMIC1 chip.
+- interrupt-parent	Phandle to the parent interrupt controller.
+- interrupts: 		The interrupt line the device is connected to.
+- #interrupt-cells: 	Should be 1.
+- interrupt-controller: Describes the STPMIC1 as an interrupt
+  controller (has its own domain). Interrupt number are the following:
+	/* Interrupt Register 1 (0x50 for latch) */
+	IT_SWOUT_R=0
+	IT_SWOUT_F=1
+	IT_VBUS_OTG_R=2
+	IT_VBUS_OTG_F=3
+	IT_WAKEUP_R=4
+	IT_WAKEUP_F=5
+	IT_PONKEY_R=6
+	IT_PONKEY_F=7
+	/* Interrupt Register 2 (0x51 for latch) */
+	IT_OVP_BOOST=8
+	IT_OCP_BOOST=9
+	IT_OCP_SWOUT=10
+	IT_OCP_OTG=11
+	IT_CURLIM_BUCK4=12
+	IT_CURLIM_BUCK3=13
+	IT_CURLIM_BUCK2=14
+	IT_CURLIM_BUCK1=15
+	/* Interrupt Register 3 (0x52 for latch) */
+	IT_SHORT_SWOUT=16
+	IT_SHORT_SWOTG=17
+	IT_CURLIM_LDO6=18
+	IT_CURLIM_LDO5=19
+	IT_CURLIM_LDO4=20
+	IT_CURLIM_LDO3=21
+	IT_CURLIM_LDO2=22
+	IT_CURLIM_LDO1=23
+	/* Interrupt Register 3 (0x52 for latch) */
+	IT_SWIN_R=24
+	IT_SWIN_F=25
+	IT_RESERVED_1=26
+	IT_RESERVED_2=27
+	IT_VINLOW_R=28
+	IT_VINLOW_F=29
+	IT_TWARN_R=30
+	IT_TWARN_F=31
+
+Optional parent device properties:
+- st,main-control-register:
+	-bit 1: Power cycling will be performed on turn OFF condition
+	-bit 2: PWRCTRL is functional
+	-bit 3: PWRCTRL active high
+- st,pads-pull-register:
+	-bit 1: WAKEUP pull down is not active
+	-bit 2: PWRCTRL pull up is active
+	-bit 3: PWRCTRL pull down is active
+	-bit 4: WAKEUP detector is disabled
+- st,vin-control-register:
+	-bit 0: VINLOW monitoring is enabled
+	-bit [1...3]: VINLOW rising threshold
+		000 VINOK_f + 50mV
+		001 VINOK_f + 100mV
+		010 VINOK_f + 150mV
+		011 VINOK_f + 200mV
+		100 VINOK_f + 250mV
+		101 VINOK_f + 300mV
+		110 VINOK_f + 350mV
+		111 VINOK_f + 400mV
+	-bit [4...5]: VINLOW hyst
+		00 100mV
+		01 200mV
+		10 300mV
+		11 400mV
+	-bit 6: SW_OUT detector is disabled
+	-bit 7: SW_IN detector is enabled.
+- st,usb-control-register:
+	-bit 3: SW_OUT current limit
+		0: 600mA
+		1: 1.1A
+	-bit 4: VBUS_OTG discharge is enabled
+	-bit 5: SW_OUT discharge is enabled
+	-bit 6: VBUS_OTG detection is enabled
+	-bit 7: BOOST_OVP is disabled
+
+STPMIC1 consists in a varied group of sub-devices.
+Each sub-device binding is be described in own documentation file.
+
+Device			 Description
+------			------------
+st,stpmic1-onkey	: Power on key, see ../input/st,stpmic1-onkey.txt
+st,stpmic1-regulators	: Regulators, see ../regulator/st,stpmic1-regulator.txt
+st,stpmic1-wdt		: Watchdog, see ../watchdog/st,stpmic1-wdt.txt
+
+Example:
+
+pmic: pmic1@33 {
+	compatible = "st,stpmic1";
+	reg = <0x33>;
+	interrupt-parent = <&gpioa>;
+	interrupts = <0 2>;
+	st,main-control-register=<0x0c>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	onkey {
+		compatible = "st,stpmic1-onkey";
+		interrupt-parent = <&pmic>;
+		interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
+		interrupt-names = "onkey-falling", "onkey-rising";
+		power-off-time-sec = <10>;
+	};
+
+	watchdog {
+		compatible = "st,stpmic1-wdt";
+	};
+
+	regulators {
+		compatible = "st,stpmic1-regulators";
+
+		vdd_core: buck1 {
+			regulator-name = "vdd_core";
+			regulator-boot-on;
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		vdd: buck3 {
+			regulator-name = "vdd";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-pull-down;
+		};
+	};
diff --git a/include/dt-bindings/mfd/st,stpmic1.h b/include/dt-bindings/mfd/st,stpmic1.h
new file mode 100644
index 0000000..b2d6c83
--- /dev/null
+++ b/include/dt-bindings/mfd/st,stpmic1.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
+ * Author: Philippe Peurichard <philippe.peurichard@st.com>,
+ * Pascal Paillet <p.paillet@st.com> for STMicroelectronics.
+ */
+
+#ifndef __DT_BINDINGS_STPMIC1_H__
+#define __DT_BINDINGS_STPMIC1_H__
+
+/* IRQ definitions */
+#define IT_PONKEY_F	0
+#define IT_PONKEY_R	1
+#define IT_WAKEUP_F	2
+#define IT_WAKEUP_R	3
+#define IT_VBUS_OTG_F	4
+#define IT_VBUS_OTG_R	5
+#define IT_SWOUT_F	6
+#define IT_SWOUT_R	7
+
+#define IT_CURLIM_BUCK1	8
+#define IT_CURLIM_BUCK2	9
+#define IT_CURLIM_BUCK3	10
+#define IT_CURLIM_BUCK4	11
+#define IT_OCP_OTG	12
+#define IT_OCP_SWOUT	13
+#define IT_OCP_BOOST	14
+#define IT_OVP_BOOST	15
+
+#define IT_CURLIM_LDO1	16
+#define IT_CURLIM_LDO2	17
+#define IT_CURLIM_LDO3	18
+#define IT_CURLIM_LDO4	19
+#define IT_CURLIM_LDO5	20
+#define IT_CURLIM_LDO6	21
+#define IT_SHORT_SWOTG	22
+#define IT_SHORT_SWOUT	23
+
+#define IT_TWARN_F	24
+#define IT_TWARN_R	25
+#define IT_VINLOW_F	26
+#define IT_VINLOW_R	27
+#define IT_SWIN_F	30
+#define IT_SWIN_R	31
+
+#endif /* __DT_BINDINGS_STPMIC1_H__ */
-- 
1.9.1