Re: [PATCH v13 20/35] mtd: rawnand: tegra: Add runtime PM and OPP support

[Dmitry Osipenko <digetx@gmail.com>]

01.10.2021 18:01, Ulf Hansson пишет:
> On Fri, 1 Oct 2021 at 16:35, Dmitry Osipenko <digetx@gmail.com> wrote:
>>
>> 01.10.2021 17:24, Ulf Hansson пишет:
>>> On Mon, 27 Sept 2021 at 00:42, Dmitry Osipenko <digetx@gmail.com> wrote:
>>>>
>>>> The NAND on Tegra belongs to the core power domain and we're going to
>>>> enable GENPD support for the core domain. Now NAND must be resumed using
>>>> runtime PM API in order to initialize the NAND power state. Add runtime PM
>>>> and OPP support to the NAND driver.
>>>>
>>>> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
>>>> Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
>>>> ---
>>>>  drivers/mtd/nand/raw/tegra_nand.c | 55 ++++++++++++++++++++++++++-----
>>>>  1 file changed, 47 insertions(+), 8 deletions(-)
>>>>
>>>> diff --git a/drivers/mtd/nand/raw/tegra_nand.c b/drivers/mtd/nand/raw/tegra_nand.c
>>>> index 32431bbe69b8..098fcc9cb9df 100644
>>>> --- a/drivers/mtd/nand/raw/tegra_nand.c
>>>> +++ b/drivers/mtd/nand/raw/tegra_nand.c
>>>> @@ -17,8 +17,11 @@
>>>>  #include <linux/mtd/rawnand.h>
>>>>  #include <linux/of.h>
>>>>  #include <linux/platform_device.h>
>>>> +#include <linux/pm_runtime.h>
>>>>  #include <linux/reset.h>
>>>>
>>>> +#include <soc/tegra/common.h>
>>>> +
>>>>  #define COMMAND                                        0x00
>>>>  #define   COMMAND_GO                           BIT(31)
>>>>  #define   COMMAND_CLE                          BIT(30)
>>>> @@ -1151,6 +1154,7 @@ static int tegra_nand_probe(struct platform_device *pdev)
>>>>                 return -ENOMEM;
>>>>
>>>>         ctrl->dev = &pdev->dev;
>>>> +       platform_set_drvdata(pdev, ctrl);
>>>>         nand_controller_init(&ctrl->controller);
>>>>         ctrl->controller.ops = &tegra_nand_controller_ops;
>>>>
>>>> @@ -1166,14 +1170,22 @@ static int tegra_nand_probe(struct platform_device *pdev)
>>>>         if (IS_ERR(ctrl->clk))
>>>>                 return PTR_ERR(ctrl->clk);
>>>>
>>>> -       err = clk_prepare_enable(ctrl->clk);
>>>> +       err = devm_pm_runtime_enable(&pdev->dev);
>>>> +       if (err)
>>>> +               return err;
>>>> +
>>>> +       err = devm_tegra_core_dev_init_opp_table_common(&pdev->dev);
>>>> +       if (err)
>>>> +               return err;
>>>> +
>>>> +       err = pm_runtime_resume_and_get(&pdev->dev);
>>>>         if (err)
>>>>                 return err;
>>>>
>>>>         err = reset_control_reset(rst);
>>>>         if (err) {
>>>>                 dev_err(ctrl->dev, "Failed to reset HW: %d\n", err);
>>>> -               goto err_disable_clk;
>>>> +               goto err_put_pm;
>>>>         }
>>>>
>>>>         writel_relaxed(HWSTATUS_CMD_DEFAULT, ctrl->regs + HWSTATUS_CMD);
>>>> @@ -1188,21 +1200,19 @@ static int tegra_nand_probe(struct platform_device *pdev)
>>>>                                dev_name(&pdev->dev), ctrl);
>>>>         if (err) {
>>>>                 dev_err(ctrl->dev, "Failed to get IRQ: %d\n", err);
>>>> -               goto err_disable_clk;
>>>> +               goto err_put_pm;
>>>>         }
>>>>
>>>>         writel_relaxed(DMA_MST_CTRL_IS_DONE, ctrl->regs + DMA_MST_CTRL);
>>>>
>>>>         err = tegra_nand_chips_init(ctrl->dev, ctrl);
>>>>         if (err)
>>>> -               goto err_disable_clk;
>>>> -
>>>> -       platform_set_drvdata(pdev, ctrl);
>>>> +               goto err_put_pm;
>>>>
>>>
>>> There is no corresponding call pm_runtime_put() here. Is it
>>> intentional to always leave the device runtime resumed after ->probe()
>>> has succeeded?
>>>
>>> I noticed you included some comments about this for some other
>>> drivers, as those needed more tweaks. Is that also the case for this
>>> driver?
>>
>> Could you please clarify? There is pm_runtime_put() in both probe-error
>> and remove() code paths here.
> 
> I was not considering the error path of ->probe() (or ->remove()), but
> was rather thinking about when ->probe() completes successfully. Then
> you keep the device runtime resumed, because you have called
> pm_runtime_resume_and_get() for it.
> 
> Shouldn't you have a corresponding pm_runtime_put() in ->probe(),
> allowing it to be runtime suspended, until the device is really needed
> later on. No?

This driver doesn't support active power management. I don't have Tegra
hardware that uses NAND storage for testing, so it's up to somebody else
to implement dynamic power management. NAND doesn't require high
voltages, so it's fine to keep the old driver behaviour by keeping
hardware resumed since the probe time.