From: Boris Brezillon <boris.brezillon@bootlin.com>
To: Naga Sureshkumar Relli <nagasure@xilinx.com>
Cc: "miquel.raynal@bootlin.com" <miquel.raynal@bootlin.com>,
"richard@nod.at" <richard@nod.at>,
"dwmw2@infradead.org" <dwmw2@infradead.org>,
"computersforpeace@gmail.com" <computersforpeace@gmail.com>,
"marek.vasut@gmail.com" <marek.vasut@gmail.com>,
"linux-mtd@lists.infradead.org" <linux-mtd@lists.infradead.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"nagasuresh12@gmail.com" <nagasuresh12@gmail.com>,
"robh@kernel.org" <robh@kernel.org>,
Michal Simek <michals@xilinx.com>
Subject: Re: [LINUX PATCH v12 3/3] mtd: rawnand: arasan: Add support for Arasan NAND Flash Controller
Date: Tue, 20 Nov 2018 12:02:44 +0100 [thread overview]
Message-ID: <20181120120244.7d2442b5@bbrezillon> (raw)
In-Reply-To: <BN6PR02MB2610C7D048E4A192E041BE14AFD90@BN6PR02MB2610.namprd02.prod.outlook.com>
On Tue, 20 Nov 2018 07:02:08 +0000
Naga Sureshkumar Relli <nagasure@xilinx.com> wrote:
> >
> > Can you please run nandbiterrs (availaible in mtd-utils). I fear your
> > device won't pass the test.
> Yes, nandbiterror test is passing till 24bit, after that it is failing.
Can you paste the output of nandbiterrs please?
> >
> > > But we are hitting this because of erased page reading(needed in case of ubifs).
> > >
> > > >
> > > > Don't you have a bit (or several bits) reporting when the ECC engine was not able to
> > correct
> > > > data? I you do, you should base the "detect bitflips in erase pages" logic on this information.
> > > Bit reporting for several bit errors is there only for Hamming(1bit correction and 2bit
> > detection) but not in BCH.
> > >
> >
> > Then I tend to agree with Miquel: your ECC engine is broken, and I'm
> > not even sure how to deal with that yet.
> So as per the Miquel's suggestion, can I proceed to add the below one?
> "you should re-read the page in raw mode and check for the number of bitflips manually (thanks to the helpers in the core). Again, if the number of BF is above 16, we can assume the page is bad and increment ->ecc.failed accordingly."
But that's just partially fixing the problem. And you didn't answer my
previous question: what happens when you configure the ECC engine in,
say 12bit/1024 and you end up with uncorrectable errors (more than 12
bitflips in a 1k block). What's the number reported ECC_ERR_CNT? Is it
set to 13?
next prev parent reply other threads:[~2018-11-20 11:03 UTC|newest]
Thread overview: 48+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-09 5:00 [LINUX PATCH v12 0/3] Add support for Arasan NAND Flash controller Naga Sureshkumar Relli
2018-11-09 5:00 ` [LINUX PATCH v12 1/3] dt-bindings: mtd: arasan: Add device tree binding documentation Naga Sureshkumar Relli
2018-11-09 6:28 ` Boris Brezillon
2018-11-09 12:33 ` Naga Sureshkumar Relli
2018-11-09 12:54 ` Miquel Raynal
2018-11-09 13:19 ` Naga Sureshkumar Relli
2018-11-16 11:50 ` Martin Lund
2018-11-16 12:10 ` Martin Lund
2018-11-16 12:33 ` Michal Simek
2018-11-16 13:50 ` Naga Sureshkumar Relli
2018-11-16 14:22 ` Martin Lund
2018-11-09 5:00 ` [LINUX PATCH v12 2/3] mtd: rawnand: Add an option to get sdr timing mode number Naga Sureshkumar Relli
2018-11-09 5:00 ` [LINUX PATCH v12 3/3] mtd: rawnand: arasan: Add support for Arasan NAND Flash Controller Naga Sureshkumar Relli
2018-11-09 8:07 ` Boris Brezillon
2018-11-09 13:18 ` Naga Sureshkumar Relli
2018-11-09 23:03 ` kbuild test robot
2018-11-12 10:55 ` Martin Lund
2018-11-12 10:58 ` Boris Brezillon
2018-11-12 12:43 ` Naga Sureshkumar Relli
2018-11-15 9:34 ` Naga Sureshkumar Relli
2018-11-18 18:52 ` Miquel Raynal
2018-11-18 19:43 ` Boris Brezillon
2018-11-19 6:20 ` Naga Sureshkumar Relli
2018-11-19 8:02 ` Boris Brezillon
2018-11-20 7:02 ` Naga Sureshkumar Relli
2018-11-20 11:02 ` Boris Brezillon [this message]
2018-11-20 12:36 ` Miquel Raynal
2018-11-23 13:53 ` Naga Sureshkumar Relli
2018-12-12 5:27 ` Naga Sureshkumar Relli
2018-12-12 8:11 ` Miquel Raynal
2018-12-12 9:04 ` Naga Sureshkumar Relli
2018-12-12 9:09 ` Miquel Raynal
2018-12-12 13:07 ` Naga Sureshkumar Relli
2018-12-12 13:18 ` Miquel Raynal
2018-12-17 13:21 ` Naga Sureshkumar Relli
2018-12-17 16:41 ` Miquel Raynal
2018-12-18 5:33 ` Naga Sureshkumar Relli
2018-12-19 14:26 ` Miquel Raynal
2018-12-21 7:36 ` Naga Sureshkumar Relli
2019-01-28 6:04 ` Naga Sureshkumar Relli
2019-01-28 9:27 ` Miquel Raynal
2019-01-28 9:35 ` Naga Sureshkumar Relli
2019-06-19 4:44 ` Naga Sureshkumar Relli
2019-06-27 16:27 ` Miquel Raynal
2019-06-28 4:20 ` Naga Sureshkumar Relli
2018-11-15 16:45 ` Dan Carpenter
2018-11-20 16:24 ` Boris Brezillon
2018-12-04 9:18 ` Naga Sureshkumar Relli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181120120244.7d2442b5@bbrezillon \
--to=boris.brezillon@bootlin.com \
--cc=computersforpeace@gmail.com \
--cc=dwmw2@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=marek.vasut@gmail.com \
--cc=michals@xilinx.com \
--cc=miquel.raynal@bootlin.com \
--cc=nagasure@xilinx.com \
--cc=nagasuresh12@gmail.com \
--cc=richard@nod.at \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).