All of lore.kernel.org
 help / color / mirror / Atom feed
From: Manasi Navare <manasi.d.navare@intel.com>
To: intel-gfx@lists.freedesktop.org
Subject: [CI v13 05/17] drm/i915/dsc: Compute Rate Control parameters for DSC
Date: Wed, 28 Nov 2018 12:26:16 -0800	[thread overview]
Message-ID: <20181128202628.20238-5-manasi.d.navare@intel.com> (raw)
In-Reply-To: <20181128202628.20238-1-manasi.d.navare@intel.com>

From: Gaurav K Singh <gaurav.k.singh@intel.com>

This computation of RC params happens in the atomic commit phase
during compute_config() to validate if display stream compression
can be enabled for the requested mode.

v7 (From Manasi):
* Use DRM_DEBUG instead of DRM_ERROR (Ville)
* Use Error numberinstead of -1 (Ville)
v6 (From Manasi):
* Use 9 instead of 0x9 for consistency (Anusha)

v5 (From Manasi):
* Fix dim checkpatch warnings/checks
v4(From Gaurav):
* No change.Rebase on drm-tip

v3 (From Gaurav):
* Rebase on top of Manasi's latest series
* Return -ve value in case of failure scenarios (Manasi)

Fix review comments from Ville:
* Remove unnecessary comments
* Remove unnecessary paranthesis
* Add comments for few RC params calculations

v2 (From Manasi):
* Rebase Gaurav's patch from intel-gfx to gfx-internal
* Use struct drm_dsc_cfg instead of struct intel_dp
as a parameter

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/intel_vdsc.c | 125 +++++++++++++++++++++++++++++-
 1 file changed, 124 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index 4ce6f0c453bb..39baff618ed8 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -318,6 +318,129 @@ static int get_column_index_for_rc_params(u8 bits_per_component)
 	}
 }
 
+static int intel_compute_rc_parameters(struct drm_dsc_config *vdsc_cfg)
+{
+	unsigned long groups_per_line = 0;
+	unsigned long groups_total = 0;
+	unsigned long num_extra_mux_bits = 0;
+	unsigned long slice_bits = 0;
+	unsigned long hrd_delay = 0;
+	unsigned long final_scale = 0;
+	unsigned long rbs_min = 0;
+
+	/* Number of groups used to code each line of a slice */
+	groups_per_line = DIV_ROUND_UP(vdsc_cfg->slice_width,
+				       DSC_RC_PIXELS_PER_GROUP);
+
+	/* chunksize in Bytes */
+	vdsc_cfg->slice_chunk_size = DIV_ROUND_UP(vdsc_cfg->slice_width *
+						  vdsc_cfg->bits_per_pixel,
+						  (8 * 16));
+
+	if (vdsc_cfg->convert_rgb)
+		num_extra_mux_bits = 3 * (vdsc_cfg->mux_word_size +
+					  (4 * vdsc_cfg->bits_per_component + 4)
+					  - 2);
+	else
+		num_extra_mux_bits = 3 * vdsc_cfg->mux_word_size +
+			(4 * vdsc_cfg->bits_per_component + 4) +
+			2 * (4 * vdsc_cfg->bits_per_component) - 2;
+	/* Number of bits in one Slice */
+	slice_bits = 8 * vdsc_cfg->slice_chunk_size * vdsc_cfg->slice_height;
+
+	while ((num_extra_mux_bits > 0) &&
+	       ((slice_bits - num_extra_mux_bits) % vdsc_cfg->mux_word_size))
+		num_extra_mux_bits--;
+
+	if (groups_per_line < vdsc_cfg->initial_scale_value - 8)
+		vdsc_cfg->initial_scale_value = groups_per_line + 8;
+
+	/* scale_decrement_interval calculation according to DSC spec 1.11 */
+	if (vdsc_cfg->initial_scale_value > 8)
+		vdsc_cfg->scale_decrement_interval = groups_per_line /
+			(vdsc_cfg->initial_scale_value - 8);
+	else
+		vdsc_cfg->scale_decrement_interval = DSC_SCALE_DECREMENT_INTERVAL_MAX;
+
+	vdsc_cfg->final_offset = vdsc_cfg->rc_model_size -
+		(vdsc_cfg->initial_xmit_delay *
+		 vdsc_cfg->bits_per_pixel + 8) / 16 + num_extra_mux_bits;
+
+	if (vdsc_cfg->final_offset >= vdsc_cfg->rc_model_size) {
+		DRM_DEBUG_KMS("FinalOfs < RcModelSze for this InitialXmitDelay\n");
+		return -ERANGE;
+	}
+
+	final_scale = (vdsc_cfg->rc_model_size * 8) /
+		(vdsc_cfg->rc_model_size - vdsc_cfg->final_offset);
+	if (vdsc_cfg->slice_height > 1)
+		/*
+		 * NflBpgOffset is 16 bit value with 11 fractional bits
+		 * hence we multiply by 2^11 for preserving the
+		 * fractional part
+		 */
+		vdsc_cfg->nfl_bpg_offset = DIV_ROUND_UP((vdsc_cfg->first_line_bpg_offset << 11),
+							(vdsc_cfg->slice_height - 1));
+	else
+		vdsc_cfg->nfl_bpg_offset = 0;
+
+	/* 2^16 - 1 */
+	if (vdsc_cfg->nfl_bpg_offset > 65535) {
+		DRM_DEBUG_KMS("NflBpgOffset is too large for this slice height\n");
+		return -ERANGE;
+	}
+
+	/* Number of groups used to code the entire slice */
+	groups_total = groups_per_line * vdsc_cfg->slice_height;
+
+	/* slice_bpg_offset is 16 bit value with 11 fractional bits */
+	vdsc_cfg->slice_bpg_offset = DIV_ROUND_UP(((vdsc_cfg->rc_model_size -
+						    vdsc_cfg->initial_offset +
+						    num_extra_mux_bits) << 11),
+						  groups_total);
+
+	if (final_scale > 9) {
+		/*
+		 * ScaleIncrementInterval =
+		 * finaloffset/((NflBpgOffset + SliceBpgOffset)*8(finalscale - 1.125))
+		 * as (NflBpgOffset + SliceBpgOffset) has 11 bit fractional value,
+		 * we need divide by 2^11 from pstDscCfg values
+		 */
+		vdsc_cfg->scale_increment_interval =
+				(vdsc_cfg->final_offset * (1 << 11)) /
+				((vdsc_cfg->nfl_bpg_offset +
+				vdsc_cfg->slice_bpg_offset) *
+				(final_scale - 9));
+	} else {
+		/*
+		 * If finalScaleValue is less than or equal to 9, a value of 0 should
+		 * be used to disable the scale increment at the end of the slice
+		 */
+		vdsc_cfg->scale_increment_interval = 0;
+	}
+
+	if (vdsc_cfg->scale_increment_interval > 65535) {
+		DRM_DEBUG_KMS("ScaleIncrementInterval is large for slice height\n");
+		return -ERANGE;
+	}
+
+	/*
+	 * DSC spec mentions that bits_per_pixel specifies the target
+	 * bits/pixel (bpp) rate that is used by the encoder,
+	 * in steps of 1/16 of a bit per pixel
+	 */
+	rbs_min = vdsc_cfg->rc_model_size - vdsc_cfg->initial_offset +
+		DIV_ROUND_UP(vdsc_cfg->initial_xmit_delay *
+			     vdsc_cfg->bits_per_pixel, 16) +
+		groups_per_line * vdsc_cfg->first_line_bpg_offset;
+
+	hrd_delay = DIV_ROUND_UP((rbs_min * 16), vdsc_cfg->bits_per_pixel);
+	vdsc_cfg->rc_bits = (hrd_delay * vdsc_cfg->bits_per_pixel) / 16;
+	vdsc_cfg->initial_dec_delay = hrd_delay - vdsc_cfg->initial_xmit_delay;
+
+	return 0;
+}
+
 int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 				struct intel_crtc_state *pipe_config)
 {
@@ -452,5 +575,5 @@ int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 	vdsc_cfg->initial_scale_value = (vdsc_cfg->rc_model_size << 3) /
 		(vdsc_cfg->rc_model_size - vdsc_cfg->initial_offset);
 
-	return 0;
+	return intel_compute_rc_parameters(vdsc_cfg);
 }
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

  parent reply	other threads:[~2018-11-28 20:23 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-28 20:26 [CI v13 01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state Manasi Navare
2018-11-28 20:26 ` [CI v13 02/17] drm/i915/dp: Compute DSC pipe config in atomic check Manasi Navare
2018-11-28 21:36   ` [PATCH v14 " Manasi Navare
2018-11-28 20:26 ` [CI v13 03/17] drm/i915/dp: Do not enable PSR2 if DSC is enabled Manasi Navare
2018-11-28 20:26 ` [CI v13 04/17] drm/i915/dsc: Define & Compute VESA DSC params Manasi Navare
2018-11-29 19:38   ` [CI v15 " Manasi Navare
2018-11-28 20:26 ` Manasi Navare [this message]
2018-11-28 20:26 ` [CI v13 06/17] drm/i915/dp: Enable/Disable DSC in DP Sink Manasi Navare
2018-11-28 20:26 ` [CI v13 07/17] drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI Manasi Navare
2018-11-28 20:26 ` [CI v13 08/17] drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling Manasi Navare
2018-11-28 20:26 ` [CI v13 09/17] drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs Manasi Navare
2018-11-28 20:26 ` [CI v13 10/17] drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes Manasi Navare
2018-11-28 20:26 ` [CI v13 11/17] drm/i915/dp: Configure Display stream splitter registers during DSC enable Manasi Navare
2018-11-28 20:26 ` [CI v13 12/17] drm/i915/dp: Disable DSC in source by disabling DSS CTL bits Manasi Navare
2018-11-28 20:26 ` [CI v13 13/17] drm/i915/dsc: Enable and disable appropriate power wells for VDSC Manasi Navare
2018-11-28 20:26 ` [CI v13 14/17] i915/dp/fec: Add fec_enable to the crtc state Manasi Navare
2018-11-28 20:26 ` [CI v13 15/17] drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION Manasi Navare
2018-11-28 20:26 ` [CI v13 16/17] i915/dp/fec: Configure the Forward Error Correction bits Manasi Navare
2018-11-28 20:26 ` [CI v13 17/17] drm/i915/fec: Disable FEC state Manasi Navare
2018-11-28 21:01 ` ✗ Fi.CI.BAT: failure for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state Patchwork
2018-11-28 22:59 ` ✗ Fi.CI.CHECKPATCH: warning for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2) Patchwork
2018-11-28 23:06 ` ✗ Fi.CI.SPARSE: " Patchwork
2018-11-28 23:15 ` ✓ Fi.CI.BAT: success " Patchwork
2018-11-29 10:29 ` ✓ Fi.CI.IGT: " Patchwork
2018-11-29 19:50 ` ✗ Fi.CI.CHECKPATCH: warning for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3) Patchwork
2018-11-29 19:56 ` ✗ Fi.CI.SPARSE: " Patchwork
2018-11-29 20:08 ` ✓ Fi.CI.BAT: success " Patchwork
2018-11-29 20:52 ` [CI v13 01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state Manasi Navare
2018-11-30 12:52 ` ✗ Fi.CI.IGT: failure for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3) Patchwork

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181128202628.20238-5-manasi.d.navare@intel.com \
    --to=manasi.d.navare@intel.com \
    --cc=intel-gfx@lists.freedesktop.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.