All of lore.kernel.org
 help / color / mirror / Atom feed
From: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
To: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org,
	spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
	sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org,
	lrg-kDsPt+C1G03kYMGBc/C6ZA@public.gmane.org,
	broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org,
	rpurdie@rpsys
Cc: dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
	khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org,
	Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>,
	akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org,
	alan-qBU/x9rampVanCEyBjwyrvXRex20P6io@public.gmane.org
Subject: [PATCH v5 06/12] regulator: add driver for tps6524x regulator
Date: Mon, 15 Nov 2010 14:12:08 -0500	[thread overview]
Message-ID: <1289848334-8695-7-git-send-email-cyril@ti.com> (raw)
In-Reply-To: <1289848334-8695-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>

TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators.  This device is interfaced using SPI.

Acked-by: Mark Brown <broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
Signed-off-by: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
---
 drivers/regulator/Kconfig              |   10 +
 drivers/regulator/Makefile             |    1 +
 drivers/regulator/tps6524x-regulator.c |  692 ++++++++++++++++++++++++++++++++
 3 files changed, 703 insertions(+), 0 deletions(-)
 create mode 100644 drivers/regulator/tps6524x-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 172951b..a6f8536 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -235,5 +235,15 @@ config REGULATOR_TPS6586X
 	help
 	  This driver supports TPS6586X voltage regulator chips.
 
+config REGULATOR_TPS6524X
+	tristate "TI TPS6524X Power regulators"
+	depends on SPI
+	help
+	  This driver supports TPS6524X voltage regulator chips. TPS6524X
+	  provides three step-down converters and two general-purpose LDO
+	  voltage regulators.  This device is interfaced using a customized
+	  serial interface currently supported on the sequencer serial
+	  port controller.
+
 endif
 
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 8285fd8..a8e5bc0 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -33,6 +33,7 @@ obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
 
 obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
+obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o
 obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o
 obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o
 obj-$(CONFIG_REGULATOR_AB8500)	+= ab8500.o
diff --git a/drivers/regulator/tps6524x-regulator.c b/drivers/regulator/tps6524x-regulator.c
new file mode 100644
index 0000000..6d6cc5e
--- /dev/null
+++ b/drivers/regulator/tps6524x-regulator.c
@@ -0,0 +1,692 @@
+/*
+ * Regulator driver for TPS6524x PMIC
+ *
+ * Copyright (C) 2010 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+#define REG_LDO_SET		0x0
+#define LDO_ILIM_MASK		1	/* 0 = 400-800, 1 = 900-1500 */
+#define LDO_VSEL_MASK		0x0f
+#define LDO2_ILIM_SHIFT		12
+#define LDO2_VSEL_SHIFT		4
+#define LDO1_ILIM_SHIFT		8
+#define LDO1_VSEL_SHIFT		0
+
+#define REG_BLOCK_EN		0x1
+#define BLOCK_MASK		1
+#define BLOCK_LDO1_SHIFT	0
+#define BLOCK_LDO2_SHIFT	1
+#define BLOCK_LCD_SHIFT		2
+#define BLOCK_USB_SHIFT		3
+
+#define REG_DCDC_SET		0x2
+#define DCDC_VDCDC_MASK		0x1f
+#define DCDC_VDCDC1_SHIFT	0
+#define DCDC_VDCDC2_SHIFT	5
+#define DCDC_VDCDC3_SHIFT	10
+
+#define REG_DCDC_EN		0x3
+#define DCDCDCDC_EN_MASK	0x1
+#define DCDCDCDC1_EN_SHIFT	0
+#define DCDCDCDC1_PG_MSK	BIT(1)
+#define DCDCDCDC2_EN_SHIFT	2
+#define DCDCDCDC2_PG_MSK	BIT(3)
+#define DCDCDCDC3_EN_SHIFT	4
+#define DCDCDCDC3_PG_MSK	BIT(5)
+
+#define REG_USB			0x4
+#define USB_ILIM_SHIFT		0
+#define USB_ILIM_MASK		0x3
+#define USB_TSD_SHIFT		2
+#define USB_TSD_MASK		0x3
+#define USB_TWARN_SHIFT		4
+#define USB_TWARN_MASK		0x3
+#define USB_IWARN_SD		BIT(6)
+#define USB_FAST_LOOP		BIT(7)
+
+#define REG_ALARM		0x5
+#define ALARM_LDO1		BIT(0)
+#define ALARM_DCDC1		BIT(1)
+#define ALARM_DCDC2		BIT(2)
+#define ALARM_DCDC3		BIT(3)
+#define ALARM_LDO2		BIT(4)
+#define ALARM_USB_WARN		BIT(5)
+#define ALARM_USB_ALARM		BIT(6)
+#define ALARM_LCD		BIT(9)
+#define ALARM_TEMP_WARM		BIT(10)
+#define ALARM_TEMP_HOT		BIT(11)
+#define ALARM_NRST		BIT(14)
+#define ALARM_POWERUP		BIT(15)
+
+#define REG_INT_ENABLE		0x6
+#define INT_LDO1		BIT(0)
+#define INT_DCDC1		BIT(1)
+#define INT_DCDC2		BIT(2)
+#define INT_DCDC3		BIT(3)
+#define INT_LDO2		BIT(4)
+#define INT_USB_WARN		BIT(5)
+#define INT_USB_ALARM		BIT(6)
+#define INT_LCD			BIT(9)
+#define INT_TEMP_WARM		BIT(10)
+#define INT_TEMP_HOT		BIT(11)
+#define INT_GLOBAL_EN		BIT(15)
+
+#define REG_INT_STATUS		0x7
+#define STATUS_LDO1		BIT(0)
+#define STATUS_DCDC1		BIT(1)
+#define STATUS_DCDC2		BIT(2)
+#define STATUS_DCDC3		BIT(3)
+#define STATUS_LDO2		BIT(4)
+#define STATUS_USB_WARN		BIT(5)
+#define STATUS_USB_ALARM	BIT(6)
+#define STATUS_LCD		BIT(9)
+#define STATUS_TEMP_WARM	BIT(10)
+#define STATUS_TEMP_HOT		BIT(11)
+
+#define REG_SOFTWARE_RESET	0xb
+#define REG_WRITE_ENABLE	0xd
+#define REG_REV_ID		0xf
+
+#define N_DCDC			3
+#define N_LDO			2
+#define N_SWITCH		2
+#define N_REGULATORS		(3 /* DCDC */ + \
+				 2 /* LDO */  + \
+				 2 /* switch */)
+
+#define FIXED_ILIMSEL		BIT(0)
+#define FIXED_VOLTAGE		BIT(1)
+
+#define CMD_READ(reg)		((reg) << 6)
+#define CMD_WRITE(reg)		(BIT(5) | (reg) << 6)
+#define STAT_CLK		BIT(3)
+#define STAT_WRITE		BIT(2)
+#define STAT_INVALID		BIT(1)
+#define STAT_WP			BIT(0)
+
+struct field {
+	int		reg;
+	int		shift;
+	int		mask;
+};
+
+struct supply_info {
+	const char	*name;
+	int		n_voltages;
+	const int	*voltages;
+	int		fixed_voltage;
+	int		n_ilimsels;
+	const int	*ilimsels;
+	int		fixed_ilimsel;
+	int		flags;
+	struct field	enable, voltage, ilimsel;
+};
+
+struct tps6524x {
+	struct device		*dev;
+	struct spi_device	*spi;
+	struct mutex		lock;
+	struct regulator_desc	desc[N_REGULATORS];
+	struct regulator_dev	*rdev[N_REGULATORS];
+};
+
+static int __read_reg(struct tps6524x *hw, int reg)
+{
+	int error = 0;
+	u16 cmd = CMD_READ(reg), in;
+	u8 status;
+	struct spi_message m;
+	struct spi_transfer t[3];
+
+	spi_message_init(&m);
+	memset(t, 0, sizeof(t));
+
+	t[0].tx_buf = &cmd;
+	t[0].len = 2;
+	t[0].bits_per_word = 12;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].rx_buf = &in;
+	t[1].len = 2;
+	t[1].bits_per_word = 16;
+	spi_message_add_tail(&t[1], &m);
+
+	t[2].rx_buf = &status;
+	t[2].len = 1;
+	t[2].bits_per_word = 4;
+	spi_message_add_tail(&t[2], &m);
+
+	error = spi_sync(hw->spi, &m);
+	if (error < 0)
+		return error;
+
+	dev_dbg(hw->dev, "read reg %d, data %x, status %x\n",
+		reg, in, status);
+
+	if (!(status & STAT_CLK) || (status & STAT_WRITE))
+		return -EIO;
+
+	if (status & STAT_INVALID)
+		return -EINVAL;
+
+	return in;
+}
+
+static int read_reg(struct tps6524x *hw, int reg)
+{
+	int ret;
+
+	mutex_lock(&hw->lock);
+	ret = __read_reg(hw, reg);
+	mutex_unlock(&hw->lock);
+
+	return ret;
+}
+
+static int __write_reg(struct tps6524x *hw, int reg, int val)
+{
+	int error = 0;
+	u16 cmd = CMD_WRITE(reg), out = val;
+	u8 status;
+	struct spi_message m;
+	struct spi_transfer t[3];
+
+	spi_message_init(&m);
+	memset(t, 0, sizeof(t));
+
+	t[0].tx_buf = &cmd;
+	t[0].len = 2;
+	t[0].bits_per_word = 12;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].tx_buf = &out;
+	t[1].len = 2;
+	t[1].bits_per_word = 16;
+	spi_message_add_tail(&t[1], &m);
+
+	t[2].rx_buf = &status;
+	t[2].len = 1;
+	t[2].bits_per_word = 4;
+	spi_message_add_tail(&t[2], &m);
+
+	error = spi_sync(hw->spi, &m);
+	if (error < 0)
+		return error;
+
+	dev_dbg(hw->dev, "wrote reg %d, data %x, status %x\n",
+		reg, out, status);
+
+	if (!(status & STAT_CLK) || !(status & STAT_WRITE))
+		return -EIO;
+
+	if (status & (STAT_INVALID | STAT_WP))
+		return -EINVAL;
+
+	return error;
+}
+
+static int __rmw_reg(struct tps6524x *hw, int reg, int mask, int val)
+{
+	int ret;
+
+	ret = __read_reg(hw, reg);
+	if (ret < 0)
+		return ret;
+
+	ret &= ~mask;
+	ret |= val;
+
+	ret = __write_reg(hw, reg, ret);
+
+	return (ret < 0) ? ret : 0;
+}
+
+static int rmw_protect(struct tps6524x *hw, int reg, int mask, int val)
+{
+	int ret;
+
+	mutex_lock(&hw->lock);
+
+	ret = __write_reg(hw, REG_WRITE_ENABLE, 1);
+	if (ret) {
+		dev_err(hw->dev, "failed to set write enable\n");
+		goto error;
+	}
+
+	ret = __rmw_reg(hw, reg, mask, val);
+	if (ret)
+		dev_err(hw->dev, "failed to rmw register %d\n", reg);
+
+	ret = __write_reg(hw, REG_WRITE_ENABLE, 0);
+	if (ret) {
+		dev_err(hw->dev, "failed to clear write enable\n");
+		goto error;
+	}
+
+error:
+	mutex_unlock(&hw->lock);
+
+	return ret;
+}
+
+static int read_field(struct tps6524x *hw, const struct field *field)
+{
+	int tmp;
+
+	tmp = read_reg(hw, field->reg);
+	if (tmp < 0)
+		return tmp;
+
+	return (tmp >> field->shift) & field->mask;
+}
+
+static int write_field(struct tps6524x *hw, const struct field *field,
+		       int val)
+{
+	if (val & ~field->mask)
+		return -EOVERFLOW;
+
+	return rmw_protect(hw, field->reg,
+				    field->mask << field->shift,
+				    val << field->shift);
+}
+
+static const int dcdc1_voltages[] = {
+	 800000,  825000,  850000,  875000,
+	 900000,  925000,  950000,  975000,
+	1000000, 1025000, 1050000, 1075000,
+	1100000, 1125000, 1150000, 1175000,
+	1200000, 1225000, 1250000, 1275000,
+	1300000, 1325000, 1350000, 1375000,
+	1400000, 1425000, 1450000, 1475000,
+	1500000, 1525000, 1550000, 1575000,
+};
+
+static const int dcdc2_voltages[] = {
+	1400000, 1450000, 1500000, 1550000,
+	1600000, 1650000, 1700000, 1750000,
+	1800000, 1850000, 1900000, 1950000,
+	2000000, 2050000, 2100000, 2150000,
+	2200000, 2250000, 2300000, 2350000,
+	2400000, 2450000, 2500000, 2550000,
+	2600000, 2650000, 2700000, 2750000,
+	2800000, 2850000, 2900000, 2950000,
+};
+
+static const int dcdc3_voltages[] = {
+	2400000, 2450000, 2500000, 2550000, 2600000,
+	2650000, 2700000, 2750000, 2800000, 2850000,
+	2900000, 2950000, 3000000, 3050000, 3100000,
+	3150000, 3200000, 3250000, 3300000, 3350000,
+	3400000, 3450000, 3500000, 3550000, 3600000,
+};
+
+static const int ldo1_voltages[] = {
+	4300000, 4350000, 4400000, 4450000,
+	4500000, 4550000, 4600000, 4650000,
+	4700000, 4750000, 4800000, 4850000,
+	4900000, 4950000, 5000000, 5050000,
+};
+
+static const int ldo2_voltages[] = {
+	1100000, 1150000, 1200000, 1250000,
+	1300000, 1700000, 1750000, 1800000,
+	1850000, 1900000, 3150000, 3200000,
+	3250000, 3300000, 3350000, 3400000,
+};
+
+static const int ldo_ilimsel[] = {
+	400000, 1500000
+};
+
+static const int usb_ilimsel[] = {
+	200000, 400000, 800000, 1000000
+};
+
+#define __MK_FIELD(_reg, _mask, _shift) \
+	{ .reg = (_reg), .mask = (_mask), .shift = (_shift), }
+
+static const struct supply_info supply_info[N_REGULATORS] = {
+	{
+		.name		= "DCDC1",
+		.flags		= FIXED_ILIMSEL,
+		.n_voltages	= ARRAY_SIZE(dcdc1_voltages),
+		.voltages	= dcdc1_voltages,
+		.fixed_ilimsel	= 2400000,
+		.enable		= __MK_FIELD(REG_DCDC_EN, DCDCDCDC_EN_MASK,
+					     DCDCDCDC1_EN_SHIFT),
+		.voltage	= __MK_FIELD(REG_DCDC_SET, DCDC_VDCDC_MASK,
+					     DCDC_VDCDC1_SHIFT),
+	},
+	{
+		.name		= "DCDC2",
+		.flags		= FIXED_ILIMSEL,
+		.n_voltages	= ARRAY_SIZE(dcdc2_voltages),
+		.voltages	= dcdc2_voltages,
+		.fixed_ilimsel	= 1200000,
+		.enable		= __MK_FIELD(REG_DCDC_EN, DCDCDCDC_EN_MASK,
+					     DCDCDCDC2_EN_SHIFT),
+		.voltage	= __MK_FIELD(REG_DCDC_SET, DCDC_VDCDC_MASK,
+					     DCDC_VDCDC2_SHIFT),
+	},
+	{
+		.name		= "DCDC3",
+		.flags		= FIXED_ILIMSEL,
+		.n_voltages	= ARRAY_SIZE(dcdc3_voltages),
+		.voltages	= dcdc3_voltages,
+		.fixed_ilimsel	= 1200000,
+		.enable		= __MK_FIELD(REG_DCDC_EN, DCDCDCDC_EN_MASK,
+					DCDCDCDC3_EN_SHIFT),
+		.voltage	= __MK_FIELD(REG_DCDC_SET, DCDC_VDCDC_MASK,
+					     DCDC_VDCDC3_SHIFT),
+	},
+	{
+		.name		= "LDO1",
+		.n_voltages	= ARRAY_SIZE(ldo1_voltages),
+		.voltages	= ldo1_voltages,
+		.n_ilimsels	= ARRAY_SIZE(ldo_ilimsel),
+		.ilimsels	= ldo_ilimsel,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_LDO1_SHIFT),
+		.voltage	= __MK_FIELD(REG_LDO_SET, LDO_VSEL_MASK,
+					     LDO1_VSEL_SHIFT),
+		.ilimsel	= __MK_FIELD(REG_LDO_SET, LDO_ILIM_MASK,
+					     LDO1_ILIM_SHIFT),
+	},
+	{
+		.name		= "LDO2",
+		.n_voltages	= ARRAY_SIZE(ldo2_voltages),
+		.voltages	= ldo2_voltages,
+		.n_ilimsels	= ARRAY_SIZE(ldo_ilimsel),
+		.ilimsels	= ldo_ilimsel,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_LDO2_SHIFT),
+		.voltage	= __MK_FIELD(REG_LDO_SET, LDO_VSEL_MASK,
+					     LDO2_VSEL_SHIFT),
+		.ilimsel	= __MK_FIELD(REG_LDO_SET, LDO_ILIM_MASK,
+					     LDO2_ILIM_SHIFT),
+	},
+	{
+		.name		= "USB",
+		.flags		= FIXED_VOLTAGE,
+		.fixed_voltage	= 5000000,
+		.n_ilimsels	= ARRAY_SIZE(usb_ilimsel),
+		.ilimsels	= usb_ilimsel,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_USB_SHIFT),
+		.ilimsel	= __MK_FIELD(REG_USB, USB_ILIM_MASK,
+					     USB_ILIM_SHIFT),
+	},
+	{
+		.name		= "LCD",
+		.flags		= FIXED_VOLTAGE | FIXED_ILIMSEL,
+		.fixed_voltage	= 5000000,
+		.fixed_ilimsel	=  400000,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_LCD_SHIFT),
+	},
+};
+
+static int list_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_VOLTAGE)
+		return selector ? -EINVAL : info->fixed_voltage;
+
+	if (selector < 0 || selector >= info->n_voltages)
+		return -EINVAL;
+
+	return info->voltages[selector];
+}
+
+static int set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int i;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_VOLTAGE)
+		return -EINVAL;
+
+	for (i = 0; i < info->n_voltages; i++)
+		if (min_uV <= info->voltages[i] &&
+		    max_uV >= info->voltages[i])
+			break;
+
+	if (i >= info->n_voltages)
+		return -EINVAL;
+
+	return write_field(hw, &info->voltage, i);
+}
+
+static int get_voltage(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int ret;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_VOLTAGE)
+		return info->fixed_voltage;
+
+	ret = read_field(hw, &info->voltage);
+	if (ret < 0)
+		return ret;
+	if (WARN_ON(ret >= info->n_voltages))
+		return -EIO;
+
+	return info->voltages[ret];
+}
+
+static int set_current_limit(struct regulator_dev *rdev, int min_uA,
+			     int max_uA)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int i;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_ILIMSEL)
+		return -EINVAL;
+
+	for (i = 0; i < info->n_ilimsels; i++)
+		if (min_uA <= info->ilimsels[i] &&
+		    max_uA >= info->ilimsels[i])
+			break;
+
+	if (i >= info->n_ilimsels)
+		return -EINVAL;
+
+	return write_field(hw, &info->ilimsel, i);
+}
+
+static int get_current_limit(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int ret;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_ILIMSEL)
+		return info->fixed_ilimsel;
+
+	ret = read_field(hw, &info->ilimsel);
+	if (ret < 0)
+		return ret;
+	if (WARN_ON(ret >= info->n_ilimsels))
+		return -EIO;
+
+	return info->ilimsels[ret];
+}
+
+static int enable_supply(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	return write_field(hw, &info->enable, 1);
+}
+
+static int disable_supply(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	return write_field(hw, &info->enable, 0);
+}
+
+static int is_supply_enabled(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	return read_field(hw, &info->enable);
+}
+
+static struct regulator_ops regulator_ops = {
+	.is_enabled		= is_supply_enabled,
+	.enable			= enable_supply,
+	.disable		= disable_supply,
+	.get_voltage		= get_voltage,
+	.set_voltage		= set_voltage,
+	.list_voltage		= list_voltage,
+	.set_current_limit	= set_current_limit,
+	.get_current_limit	= get_current_limit,
+};
+
+static int __devexit pmic_remove(struct spi_device *spi)
+{
+	struct tps6524x *hw = spi_get_drvdata(spi);
+	int i;
+
+	if (!hw)
+		return 0;
+	for (i = 0; i < N_REGULATORS; i++) {
+		if (hw->rdev[i])
+			regulator_unregister(hw->rdev[i]);
+		hw->rdev[i] = NULL;
+	}
+	spi_set_drvdata(spi, NULL);
+	kfree(hw);
+	return 0;
+}
+
+static int __devinit pmic_probe(struct spi_device *spi)
+{
+	struct tps6524x *hw;
+	struct device *dev = &spi->dev;
+	const struct supply_info *info = supply_info;
+	struct regulator_init_data *init_data;
+	int ret = 0, i;
+
+	init_data = dev->platform_data;
+	if (!init_data) {
+		dev_err(dev, "could not find regulator platform data\n");
+		return -EINVAL;
+	}
+
+	hw = kzalloc(sizeof(struct tps6524x), GFP_KERNEL);
+	if (!hw) {
+		dev_err(dev, "cannot allocate regulator private data\n");
+		return -ENOMEM;
+	}
+	spi_set_drvdata(spi, hw);
+
+	memset(hw, 0, sizeof(struct tps6524x));
+	hw->dev = dev;
+	hw->spi = spi_dev_get(spi);
+	mutex_init(&hw->lock);
+
+	for (i = 0; i < N_REGULATORS; i++, info++, init_data++) {
+		hw->desc[i].name	= info->name;
+		hw->desc[i].id		= i;
+		hw->desc[i].n_voltages	= info->n_voltages;
+		hw->desc[i].ops		= &regulator_ops;
+		hw->desc[i].type	= REGULATOR_VOLTAGE;
+		hw->desc[i].owner	= THIS_MODULE;
+
+		if (info->flags & FIXED_VOLTAGE)
+			hw->desc[i].n_voltages = 1;
+
+		hw->rdev[i] = regulator_register(&hw->desc[i], dev,
+						 init_data, hw);
+		if (IS_ERR(hw->rdev[i])) {
+			ret = PTR_ERR(hw->rdev[i]);
+			hw->rdev[i] = NULL;
+			goto fail;
+		}
+	}
+
+	return 0;
+
+fail:
+	pmic_remove(spi);
+	return ret;
+}
+
+static struct spi_driver pmic_driver = {
+	.probe		= pmic_probe,
+	.remove		= __devexit_p(pmic_remove),
+	.driver		= {
+		.name	= "tps6524x",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init pmic_driver_init(void)
+{
+	return spi_register_driver(&pmic_driver);
+}
+subsys_initcall_sync(pmic_driver_init);
+
+static void __exit pmic_driver_exit(void)
+{
+	spi_unregister_driver(&pmic_driver);
+}
+module_exit(pmic_driver_exit);
+
+MODULE_DESCRIPTION("TPS6524X PMIC Driver");
+MODULE_AUTHOR("Cyril Chemparathy");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("spi:tps6524x");
-- 
1.7.1


------------------------------------------------------------------------------
Centralized Desktop Delivery: Dell and VMware Reference Architecture
Simplifying enterprise desktop deployment and management using
Dell EqualLogic storage and VMware View: A highly scalable, end-to-end
client virtualization framework. Read more!
http://p.sf.net/sfu/dell-eql-dev2dev

WARNING: multiple messages have this Message-ID (diff)
From: cyril@ti.com (Cyril Chemparathy)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v5 06/12] regulator: add driver for tps6524x regulator
Date: Mon, 15 Nov 2010 14:12:08 -0500	[thread overview]
Message-ID: <1289848334-8695-7-git-send-email-cyril@ti.com> (raw)
In-Reply-To: <1289848334-8695-1-git-send-email-cyril@ti.com>

TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators.  This device is interfaced using SPI.

Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
---
 drivers/regulator/Kconfig              |   10 +
 drivers/regulator/Makefile             |    1 +
 drivers/regulator/tps6524x-regulator.c |  692 ++++++++++++++++++++++++++++++++
 3 files changed, 703 insertions(+), 0 deletions(-)
 create mode 100644 drivers/regulator/tps6524x-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 172951b..a6f8536 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -235,5 +235,15 @@ config REGULATOR_TPS6586X
 	help
 	  This driver supports TPS6586X voltage regulator chips.
 
+config REGULATOR_TPS6524X
+	tristate "TI TPS6524X Power regulators"
+	depends on SPI
+	help
+	  This driver supports TPS6524X voltage regulator chips. TPS6524X
+	  provides three step-down converters and two general-purpose LDO
+	  voltage regulators.  This device is interfaced using a customized
+	  serial interface currently supported on the sequencer serial
+	  port controller.
+
 endif
 
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 8285fd8..a8e5bc0 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -33,6 +33,7 @@ obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
 
 obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
+obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o
 obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o
 obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o
 obj-$(CONFIG_REGULATOR_AB8500)	+= ab8500.o
diff --git a/drivers/regulator/tps6524x-regulator.c b/drivers/regulator/tps6524x-regulator.c
new file mode 100644
index 0000000..6d6cc5e
--- /dev/null
+++ b/drivers/regulator/tps6524x-regulator.c
@@ -0,0 +1,692 @@
+/*
+ * Regulator driver for TPS6524x PMIC
+ *
+ * Copyright (C) 2010 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+#define REG_LDO_SET		0x0
+#define LDO_ILIM_MASK		1	/* 0 = 400-800, 1 = 900-1500 */
+#define LDO_VSEL_MASK		0x0f
+#define LDO2_ILIM_SHIFT		12
+#define LDO2_VSEL_SHIFT		4
+#define LDO1_ILIM_SHIFT		8
+#define LDO1_VSEL_SHIFT		0
+
+#define REG_BLOCK_EN		0x1
+#define BLOCK_MASK		1
+#define BLOCK_LDO1_SHIFT	0
+#define BLOCK_LDO2_SHIFT	1
+#define BLOCK_LCD_SHIFT		2
+#define BLOCK_USB_SHIFT		3
+
+#define REG_DCDC_SET		0x2
+#define DCDC_VDCDC_MASK		0x1f
+#define DCDC_VDCDC1_SHIFT	0
+#define DCDC_VDCDC2_SHIFT	5
+#define DCDC_VDCDC3_SHIFT	10
+
+#define REG_DCDC_EN		0x3
+#define DCDCDCDC_EN_MASK	0x1
+#define DCDCDCDC1_EN_SHIFT	0
+#define DCDCDCDC1_PG_MSK	BIT(1)
+#define DCDCDCDC2_EN_SHIFT	2
+#define DCDCDCDC2_PG_MSK	BIT(3)
+#define DCDCDCDC3_EN_SHIFT	4
+#define DCDCDCDC3_PG_MSK	BIT(5)
+
+#define REG_USB			0x4
+#define USB_ILIM_SHIFT		0
+#define USB_ILIM_MASK		0x3
+#define USB_TSD_SHIFT		2
+#define USB_TSD_MASK		0x3
+#define USB_TWARN_SHIFT		4
+#define USB_TWARN_MASK		0x3
+#define USB_IWARN_SD		BIT(6)
+#define USB_FAST_LOOP		BIT(7)
+
+#define REG_ALARM		0x5
+#define ALARM_LDO1		BIT(0)
+#define ALARM_DCDC1		BIT(1)
+#define ALARM_DCDC2		BIT(2)
+#define ALARM_DCDC3		BIT(3)
+#define ALARM_LDO2		BIT(4)
+#define ALARM_USB_WARN		BIT(5)
+#define ALARM_USB_ALARM		BIT(6)
+#define ALARM_LCD		BIT(9)
+#define ALARM_TEMP_WARM		BIT(10)
+#define ALARM_TEMP_HOT		BIT(11)
+#define ALARM_NRST		BIT(14)
+#define ALARM_POWERUP		BIT(15)
+
+#define REG_INT_ENABLE		0x6
+#define INT_LDO1		BIT(0)
+#define INT_DCDC1		BIT(1)
+#define INT_DCDC2		BIT(2)
+#define INT_DCDC3		BIT(3)
+#define INT_LDO2		BIT(4)
+#define INT_USB_WARN		BIT(5)
+#define INT_USB_ALARM		BIT(6)
+#define INT_LCD			BIT(9)
+#define INT_TEMP_WARM		BIT(10)
+#define INT_TEMP_HOT		BIT(11)
+#define INT_GLOBAL_EN		BIT(15)
+
+#define REG_INT_STATUS		0x7
+#define STATUS_LDO1		BIT(0)
+#define STATUS_DCDC1		BIT(1)
+#define STATUS_DCDC2		BIT(2)
+#define STATUS_DCDC3		BIT(3)
+#define STATUS_LDO2		BIT(4)
+#define STATUS_USB_WARN		BIT(5)
+#define STATUS_USB_ALARM	BIT(6)
+#define STATUS_LCD		BIT(9)
+#define STATUS_TEMP_WARM	BIT(10)
+#define STATUS_TEMP_HOT		BIT(11)
+
+#define REG_SOFTWARE_RESET	0xb
+#define REG_WRITE_ENABLE	0xd
+#define REG_REV_ID		0xf
+
+#define N_DCDC			3
+#define N_LDO			2
+#define N_SWITCH		2
+#define N_REGULATORS		(3 /* DCDC */ + \
+				 2 /* LDO */  + \
+				 2 /* switch */)
+
+#define FIXED_ILIMSEL		BIT(0)
+#define FIXED_VOLTAGE		BIT(1)
+
+#define CMD_READ(reg)		((reg) << 6)
+#define CMD_WRITE(reg)		(BIT(5) | (reg) << 6)
+#define STAT_CLK		BIT(3)
+#define STAT_WRITE		BIT(2)
+#define STAT_INVALID		BIT(1)
+#define STAT_WP			BIT(0)
+
+struct field {
+	int		reg;
+	int		shift;
+	int		mask;
+};
+
+struct supply_info {
+	const char	*name;
+	int		n_voltages;
+	const int	*voltages;
+	int		fixed_voltage;
+	int		n_ilimsels;
+	const int	*ilimsels;
+	int		fixed_ilimsel;
+	int		flags;
+	struct field	enable, voltage, ilimsel;
+};
+
+struct tps6524x {
+	struct device		*dev;
+	struct spi_device	*spi;
+	struct mutex		lock;
+	struct regulator_desc	desc[N_REGULATORS];
+	struct regulator_dev	*rdev[N_REGULATORS];
+};
+
+static int __read_reg(struct tps6524x *hw, int reg)
+{
+	int error = 0;
+	u16 cmd = CMD_READ(reg), in;
+	u8 status;
+	struct spi_message m;
+	struct spi_transfer t[3];
+
+	spi_message_init(&m);
+	memset(t, 0, sizeof(t));
+
+	t[0].tx_buf = &cmd;
+	t[0].len = 2;
+	t[0].bits_per_word = 12;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].rx_buf = &in;
+	t[1].len = 2;
+	t[1].bits_per_word = 16;
+	spi_message_add_tail(&t[1], &m);
+
+	t[2].rx_buf = &status;
+	t[2].len = 1;
+	t[2].bits_per_word = 4;
+	spi_message_add_tail(&t[2], &m);
+
+	error = spi_sync(hw->spi, &m);
+	if (error < 0)
+		return error;
+
+	dev_dbg(hw->dev, "read reg %d, data %x, status %x\n",
+		reg, in, status);
+
+	if (!(status & STAT_CLK) || (status & STAT_WRITE))
+		return -EIO;
+
+	if (status & STAT_INVALID)
+		return -EINVAL;
+
+	return in;
+}
+
+static int read_reg(struct tps6524x *hw, int reg)
+{
+	int ret;
+
+	mutex_lock(&hw->lock);
+	ret = __read_reg(hw, reg);
+	mutex_unlock(&hw->lock);
+
+	return ret;
+}
+
+static int __write_reg(struct tps6524x *hw, int reg, int val)
+{
+	int error = 0;
+	u16 cmd = CMD_WRITE(reg), out = val;
+	u8 status;
+	struct spi_message m;
+	struct spi_transfer t[3];
+
+	spi_message_init(&m);
+	memset(t, 0, sizeof(t));
+
+	t[0].tx_buf = &cmd;
+	t[0].len = 2;
+	t[0].bits_per_word = 12;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].tx_buf = &out;
+	t[1].len = 2;
+	t[1].bits_per_word = 16;
+	spi_message_add_tail(&t[1], &m);
+
+	t[2].rx_buf = &status;
+	t[2].len = 1;
+	t[2].bits_per_word = 4;
+	spi_message_add_tail(&t[2], &m);
+
+	error = spi_sync(hw->spi, &m);
+	if (error < 0)
+		return error;
+
+	dev_dbg(hw->dev, "wrote reg %d, data %x, status %x\n",
+		reg, out, status);
+
+	if (!(status & STAT_CLK) || !(status & STAT_WRITE))
+		return -EIO;
+
+	if (status & (STAT_INVALID | STAT_WP))
+		return -EINVAL;
+
+	return error;
+}
+
+static int __rmw_reg(struct tps6524x *hw, int reg, int mask, int val)
+{
+	int ret;
+
+	ret = __read_reg(hw, reg);
+	if (ret < 0)
+		return ret;
+
+	ret &= ~mask;
+	ret |= val;
+
+	ret = __write_reg(hw, reg, ret);
+
+	return (ret < 0) ? ret : 0;
+}
+
+static int rmw_protect(struct tps6524x *hw, int reg, int mask, int val)
+{
+	int ret;
+
+	mutex_lock(&hw->lock);
+
+	ret = __write_reg(hw, REG_WRITE_ENABLE, 1);
+	if (ret) {
+		dev_err(hw->dev, "failed to set write enable\n");
+		goto error;
+	}
+
+	ret = __rmw_reg(hw, reg, mask, val);
+	if (ret)
+		dev_err(hw->dev, "failed to rmw register %d\n", reg);
+
+	ret = __write_reg(hw, REG_WRITE_ENABLE, 0);
+	if (ret) {
+		dev_err(hw->dev, "failed to clear write enable\n");
+		goto error;
+	}
+
+error:
+	mutex_unlock(&hw->lock);
+
+	return ret;
+}
+
+static int read_field(struct tps6524x *hw, const struct field *field)
+{
+	int tmp;
+
+	tmp = read_reg(hw, field->reg);
+	if (tmp < 0)
+		return tmp;
+
+	return (tmp >> field->shift) & field->mask;
+}
+
+static int write_field(struct tps6524x *hw, const struct field *field,
+		       int val)
+{
+	if (val & ~field->mask)
+		return -EOVERFLOW;
+
+	return rmw_protect(hw, field->reg,
+				    field->mask << field->shift,
+				    val << field->shift);
+}
+
+static const int dcdc1_voltages[] = {
+	 800000,  825000,  850000,  875000,
+	 900000,  925000,  950000,  975000,
+	1000000, 1025000, 1050000, 1075000,
+	1100000, 1125000, 1150000, 1175000,
+	1200000, 1225000, 1250000, 1275000,
+	1300000, 1325000, 1350000, 1375000,
+	1400000, 1425000, 1450000, 1475000,
+	1500000, 1525000, 1550000, 1575000,
+};
+
+static const int dcdc2_voltages[] = {
+	1400000, 1450000, 1500000, 1550000,
+	1600000, 1650000, 1700000, 1750000,
+	1800000, 1850000, 1900000, 1950000,
+	2000000, 2050000, 2100000, 2150000,
+	2200000, 2250000, 2300000, 2350000,
+	2400000, 2450000, 2500000, 2550000,
+	2600000, 2650000, 2700000, 2750000,
+	2800000, 2850000, 2900000, 2950000,
+};
+
+static const int dcdc3_voltages[] = {
+	2400000, 2450000, 2500000, 2550000, 2600000,
+	2650000, 2700000, 2750000, 2800000, 2850000,
+	2900000, 2950000, 3000000, 3050000, 3100000,
+	3150000, 3200000, 3250000, 3300000, 3350000,
+	3400000, 3450000, 3500000, 3550000, 3600000,
+};
+
+static const int ldo1_voltages[] = {
+	4300000, 4350000, 4400000, 4450000,
+	4500000, 4550000, 4600000, 4650000,
+	4700000, 4750000, 4800000, 4850000,
+	4900000, 4950000, 5000000, 5050000,
+};
+
+static const int ldo2_voltages[] = {
+	1100000, 1150000, 1200000, 1250000,
+	1300000, 1700000, 1750000, 1800000,
+	1850000, 1900000, 3150000, 3200000,
+	3250000, 3300000, 3350000, 3400000,
+};
+
+static const int ldo_ilimsel[] = {
+	400000, 1500000
+};
+
+static const int usb_ilimsel[] = {
+	200000, 400000, 800000, 1000000
+};
+
+#define __MK_FIELD(_reg, _mask, _shift) \
+	{ .reg = (_reg), .mask = (_mask), .shift = (_shift), }
+
+static const struct supply_info supply_info[N_REGULATORS] = {
+	{
+		.name		= "DCDC1",
+		.flags		= FIXED_ILIMSEL,
+		.n_voltages	= ARRAY_SIZE(dcdc1_voltages),
+		.voltages	= dcdc1_voltages,
+		.fixed_ilimsel	= 2400000,
+		.enable		= __MK_FIELD(REG_DCDC_EN, DCDCDCDC_EN_MASK,
+					     DCDCDCDC1_EN_SHIFT),
+		.voltage	= __MK_FIELD(REG_DCDC_SET, DCDC_VDCDC_MASK,
+					     DCDC_VDCDC1_SHIFT),
+	},
+	{
+		.name		= "DCDC2",
+		.flags		= FIXED_ILIMSEL,
+		.n_voltages	= ARRAY_SIZE(dcdc2_voltages),
+		.voltages	= dcdc2_voltages,
+		.fixed_ilimsel	= 1200000,
+		.enable		= __MK_FIELD(REG_DCDC_EN, DCDCDCDC_EN_MASK,
+					     DCDCDCDC2_EN_SHIFT),
+		.voltage	= __MK_FIELD(REG_DCDC_SET, DCDC_VDCDC_MASK,
+					     DCDC_VDCDC2_SHIFT),
+	},
+	{
+		.name		= "DCDC3",
+		.flags		= FIXED_ILIMSEL,
+		.n_voltages	= ARRAY_SIZE(dcdc3_voltages),
+		.voltages	= dcdc3_voltages,
+		.fixed_ilimsel	= 1200000,
+		.enable		= __MK_FIELD(REG_DCDC_EN, DCDCDCDC_EN_MASK,
+					DCDCDCDC3_EN_SHIFT),
+		.voltage	= __MK_FIELD(REG_DCDC_SET, DCDC_VDCDC_MASK,
+					     DCDC_VDCDC3_SHIFT),
+	},
+	{
+		.name		= "LDO1",
+		.n_voltages	= ARRAY_SIZE(ldo1_voltages),
+		.voltages	= ldo1_voltages,
+		.n_ilimsels	= ARRAY_SIZE(ldo_ilimsel),
+		.ilimsels	= ldo_ilimsel,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_LDO1_SHIFT),
+		.voltage	= __MK_FIELD(REG_LDO_SET, LDO_VSEL_MASK,
+					     LDO1_VSEL_SHIFT),
+		.ilimsel	= __MK_FIELD(REG_LDO_SET, LDO_ILIM_MASK,
+					     LDO1_ILIM_SHIFT),
+	},
+	{
+		.name		= "LDO2",
+		.n_voltages	= ARRAY_SIZE(ldo2_voltages),
+		.voltages	= ldo2_voltages,
+		.n_ilimsels	= ARRAY_SIZE(ldo_ilimsel),
+		.ilimsels	= ldo_ilimsel,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_LDO2_SHIFT),
+		.voltage	= __MK_FIELD(REG_LDO_SET, LDO_VSEL_MASK,
+					     LDO2_VSEL_SHIFT),
+		.ilimsel	= __MK_FIELD(REG_LDO_SET, LDO_ILIM_MASK,
+					     LDO2_ILIM_SHIFT),
+	},
+	{
+		.name		= "USB",
+		.flags		= FIXED_VOLTAGE,
+		.fixed_voltage	= 5000000,
+		.n_ilimsels	= ARRAY_SIZE(usb_ilimsel),
+		.ilimsels	= usb_ilimsel,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_USB_SHIFT),
+		.ilimsel	= __MK_FIELD(REG_USB, USB_ILIM_MASK,
+					     USB_ILIM_SHIFT),
+	},
+	{
+		.name		= "LCD",
+		.flags		= FIXED_VOLTAGE | FIXED_ILIMSEL,
+		.fixed_voltage	= 5000000,
+		.fixed_ilimsel	=  400000,
+		.enable		= __MK_FIELD(REG_BLOCK_EN, BLOCK_MASK,
+					     BLOCK_LCD_SHIFT),
+	},
+};
+
+static int list_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_VOLTAGE)
+		return selector ? -EINVAL : info->fixed_voltage;
+
+	if (selector < 0 || selector >= info->n_voltages)
+		return -EINVAL;
+
+	return info->voltages[selector];
+}
+
+static int set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int i;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_VOLTAGE)
+		return -EINVAL;
+
+	for (i = 0; i < info->n_voltages; i++)
+		if (min_uV <= info->voltages[i] &&
+		    max_uV >= info->voltages[i])
+			break;
+
+	if (i >= info->n_voltages)
+		return -EINVAL;
+
+	return write_field(hw, &info->voltage, i);
+}
+
+static int get_voltage(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int ret;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_VOLTAGE)
+		return info->fixed_voltage;
+
+	ret = read_field(hw, &info->voltage);
+	if (ret < 0)
+		return ret;
+	if (WARN_ON(ret >= info->n_voltages))
+		return -EIO;
+
+	return info->voltages[ret];
+}
+
+static int set_current_limit(struct regulator_dev *rdev, int min_uA,
+			     int max_uA)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int i;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_ILIMSEL)
+		return -EINVAL;
+
+	for (i = 0; i < info->n_ilimsels; i++)
+		if (min_uA <= info->ilimsels[i] &&
+		    max_uA >= info->ilimsels[i])
+			break;
+
+	if (i >= info->n_ilimsels)
+		return -EINVAL;
+
+	return write_field(hw, &info->ilimsel, i);
+}
+
+static int get_current_limit(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+	int ret;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	if (info->flags & FIXED_ILIMSEL)
+		return info->fixed_ilimsel;
+
+	ret = read_field(hw, &info->ilimsel);
+	if (ret < 0)
+		return ret;
+	if (WARN_ON(ret >= info->n_ilimsels))
+		return -EIO;
+
+	return info->ilimsels[ret];
+}
+
+static int enable_supply(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	return write_field(hw, &info->enable, 1);
+}
+
+static int disable_supply(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	return write_field(hw, &info->enable, 0);
+}
+
+static int is_supply_enabled(struct regulator_dev *rdev)
+{
+	const struct supply_info *info;
+	struct tps6524x *hw;
+
+	hw	= rdev_get_drvdata(rdev);
+	info	= &supply_info[rdev_get_id(rdev)];
+
+	return read_field(hw, &info->enable);
+}
+
+static struct regulator_ops regulator_ops = {
+	.is_enabled		= is_supply_enabled,
+	.enable			= enable_supply,
+	.disable		= disable_supply,
+	.get_voltage		= get_voltage,
+	.set_voltage		= set_voltage,
+	.list_voltage		= list_voltage,
+	.set_current_limit	= set_current_limit,
+	.get_current_limit	= get_current_limit,
+};
+
+static int __devexit pmic_remove(struct spi_device *spi)
+{
+	struct tps6524x *hw = spi_get_drvdata(spi);
+	int i;
+
+	if (!hw)
+		return 0;
+	for (i = 0; i < N_REGULATORS; i++) {
+		if (hw->rdev[i])
+			regulator_unregister(hw->rdev[i]);
+		hw->rdev[i] = NULL;
+	}
+	spi_set_drvdata(spi, NULL);
+	kfree(hw);
+	return 0;
+}
+
+static int __devinit pmic_probe(struct spi_device *spi)
+{
+	struct tps6524x *hw;
+	struct device *dev = &spi->dev;
+	const struct supply_info *info = supply_info;
+	struct regulator_init_data *init_data;
+	int ret = 0, i;
+
+	init_data = dev->platform_data;
+	if (!init_data) {
+		dev_err(dev, "could not find regulator platform data\n");
+		return -EINVAL;
+	}
+
+	hw = kzalloc(sizeof(struct tps6524x), GFP_KERNEL);
+	if (!hw) {
+		dev_err(dev, "cannot allocate regulator private data\n");
+		return -ENOMEM;
+	}
+	spi_set_drvdata(spi, hw);
+
+	memset(hw, 0, sizeof(struct tps6524x));
+	hw->dev = dev;
+	hw->spi = spi_dev_get(spi);
+	mutex_init(&hw->lock);
+
+	for (i = 0; i < N_REGULATORS; i++, info++, init_data++) {
+		hw->desc[i].name	= info->name;
+		hw->desc[i].id		= i;
+		hw->desc[i].n_voltages	= info->n_voltages;
+		hw->desc[i].ops		= &regulator_ops;
+		hw->desc[i].type	= REGULATOR_VOLTAGE;
+		hw->desc[i].owner	= THIS_MODULE;
+
+		if (info->flags & FIXED_VOLTAGE)
+			hw->desc[i].n_voltages = 1;
+
+		hw->rdev[i] = regulator_register(&hw->desc[i], dev,
+						 init_data, hw);
+		if (IS_ERR(hw->rdev[i])) {
+			ret = PTR_ERR(hw->rdev[i]);
+			hw->rdev[i] = NULL;
+			goto fail;
+		}
+	}
+
+	return 0;
+
+fail:
+	pmic_remove(spi);
+	return ret;
+}
+
+static struct spi_driver pmic_driver = {
+	.probe		= pmic_probe,
+	.remove		= __devexit_p(pmic_remove),
+	.driver		= {
+		.name	= "tps6524x",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init pmic_driver_init(void)
+{
+	return spi_register_driver(&pmic_driver);
+}
+subsys_initcall_sync(pmic_driver_init);
+
+static void __exit pmic_driver_exit(void)
+{
+	spi_unregister_driver(&pmic_driver);
+}
+module_exit(pmic_driver_exit);
+
+MODULE_DESCRIPTION("TPS6524X PMIC Driver");
+MODULE_AUTHOR("Cyril Chemparathy");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("spi:tps6524x");
-- 
1.7.1

  parent reply	other threads:[~2010-11-15 19:12 UTC|newest]

Thread overview: 74+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-11-15 19:12 [PATCH v5 00/12] tnetv107x ssp drivers Cyril Chemparathy
2010-11-15 19:12 ` Cyril Chemparathy
     [not found] ` <1289848334-8695-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-11-15 19:12   ` [PATCH v5 01/12] misc: add driver for sequencer serial port Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
     [not found]     ` <1289848334-8695-2-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-11-16  7:10       ` Grant Likely
2010-11-16  7:10         ` Grant Likely
     [not found]         ` <20101116071047.GE4074-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2010-11-16 16:15           ` Cyril Chemparathy
2010-11-16 16:15             ` Cyril Chemparathy
     [not found]             ` <4CE2AE3C.4040805-l0cyMroinI0@public.gmane.org>
2010-11-16 20:35               ` Grant Likely
2010-11-16 20:35                 ` Grant Likely
     [not found]                 ` <AANLkTik76EY8Xh01YP2Tep6k1ETPO+3idmNuk3pVikJG-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-11-16 21:19                   ` Cyril Chemparathy
2010-11-16 21:19                     ` Cyril Chemparathy
2010-11-16 22:23                   ` Russell King - ARM Linux
2010-11-16 22:23                     ` Russell King - ARM Linux
     [not found]                     ` <20101116222340.GF21926-l+eeeJia6m9vn6HldHNs0ANdhmdF6hFW@public.gmane.org>
2010-11-16 23:57                       ` Grant Likely
2010-11-16 23:57                         ` Grant Likely
2010-11-15 19:12   ` [PATCH v5 02/12] davinci: add tnetv107x ssp platform device Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 03/12] davinci: add ssp config for tnetv107x evm board Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 04/12] spi: add ti-ssp spi master driver Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 21:59     ` Ryan Mallon
2010-11-15 21:59       ` Ryan Mallon
     [not found]     ` <1289848334-8695-5-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-11-16  7:22       ` Grant Likely
2010-11-16  7:22         ` Grant Likely
     [not found]         ` <20101116072225.GF4074-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2010-11-16  7:47           ` Grant Likely
2010-11-16  7:47             ` Grant Likely
2010-11-16 11:34             ` Mark Brown
2010-11-16 11:34               ` Mark Brown
     [not found]               ` <20101116113409.GH3338-GFdadSzt00ze9xe1eoZjHA@public.gmane.org>
2010-11-16 20:45                 ` Grant Likely
2010-11-16 20:45                   ` Grant Likely
     [not found]                   ` <20101116204554.GB5016-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2010-11-16 22:48                     ` Mark Brown
2010-11-16 22:48                       ` Mark Brown
     [not found]             ` <AANLkTi=utWumLKo9QVWXpkC8WxpgaNJJs+dj=pa2eq-q-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-11-17  0:17               ` Cyril Chemparathy
2010-11-17  0:17                 ` Cyril Chemparathy
2010-11-17 13:31                 ` Mark Brown
2010-11-17 13:31                   ` Mark Brown
     [not found]                   ` <20101117133136.GA19488-HF5t3jzXg/6ND3a5+9QAFujbO/Zr0HzV@public.gmane.org>
2010-11-17 15:25                     ` David Brownell
2010-11-17 15:25                       ` David Brownell
     [not found]                       ` <781931.83221.qm-g47maUHHHF+ORdMXk8NaZPu2YVrzzGjVVpNB7YpNyf8@public.gmane.org>
2010-11-17 17:54                         ` Cyril Chemparathy
2010-11-17 17:54                           ` Cyril Chemparathy
     [not found]                 ` <4CE31F0E.7050103-l0cyMroinI0@public.gmane.org>
2010-11-17 16:11                   ` Grant Likely
2010-11-17 16:11                     ` Grant Likely
     [not found]                     ` <20101117161130.GC5757-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2010-11-17 17:23                       ` Mark Brown
2010-11-17 17:23                         ` Mark Brown
2010-11-17 17:35                       ` Cyril Chemparathy
2010-11-17 17:35                         ` Cyril Chemparathy
2010-11-18  5:46                       ` Greg KH
2010-11-18  5:46                         ` Greg KH
2010-11-25 23:32                         ` Rafael J. Wysocki
2010-11-25 23:32                           ` Rafael J. Wysocki
2010-11-16 14:19           ` David Brownell
2010-11-16 14:19             ` David Brownell
2010-11-15 19:12   ` [PATCH v5 05/12] davinci: add spi devices on tnetv107x evm Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` Cyril Chemparathy [this message]
2010-11-15 19:12     ` [PATCH v5 06/12] regulator: add driver for tps6524x regulator Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 07/12] davinci: add tnetv107x evm regulators Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 08/12] gpio: add ti-ssp gpio driver Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
     [not found]     ` <1289848334-8695-9-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-11-15 22:38       ` Ryan Mallon
2010-11-15 22:38         ` Ryan Mallon
     [not found]         ` <4CE1B651.1060006-7Wk5F4Od5/oYd5yxfr4S2w@public.gmane.org>
2010-11-16 19:38           ` Cyril Chemparathy
2010-11-16 19:38             ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 09/12] davinci: add tnetv107x evm ti-ssp gpio device Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 10/12] backlight: add support for tps6116x controller Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 11/12] davinci: add tnetv107x evm backlight device Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy
2010-11-15 19:12   ` [PATCH v5 12/12] davinci: add tnetv107x evm i2c eeprom device Cyril Chemparathy
2010-11-15 19:12     ` Cyril Chemparathy

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1289848334-8695-7-git-send-email-cyril@ti.com \
    --to=cyril-l0cymroini0@public.gmane.org \
    --cc=akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org \
    --cc=alan-qBU/x9rampVanCEyBjwyrvXRex20P6io@public.gmane.org \
    --cc=broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
    --cc=davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org \
    --cc=dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
    --cc=khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org \
    --cc=lrg-kDsPt+C1G03kYMGBc/C6ZA@public.gmane.org \
    --cc=rpurdie@rpsys \
    --cc=sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org \
    --cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.