From: Tony Lindgren <tony@atomide.com> To: Paul Walmsley <paul@pwsan.com> Cc: linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org, "Péter Ujfalusi" <peter.ujfalusi@ti.com>, "Benoît Cousson" <b-cousson@ti.com> Subject: Re: [PATCHv2 07/12] ARM: OMAP4+: AESS: enable internal auto-gating during initial setup Date: Sun, 10 Jun 2012 23:29:06 -0700 [thread overview] Message-ID: <20120611062905.GS12766@atomide.com> (raw) In-Reply-To: <20120611004611.20034.60143.stgit@dusk> Hi, Few comments below on making the platform_data work better along with other archs. * Paul Walmsley <paul@pwsan.com> [120610 17:56]: > Enable the AESS auto-gating control bit during AESS hwmod setup. This > fixes the following boot warning on OMAP4: ... > --- /dev/null > +++ b/include/linux/platform_data/aess.h This should be include/linux/platform_data/omap-aess.h or similar as there are other aess controllers too. > +/* > + * AESS_AUTO_GATING_ENABLE_OFFSET: offset in bytes of the AESS IP > + * block's AESS_AUTO_GATING_ENABLE__1 register from the IP block's > + * base address > + */ > +#define AESS_AUTO_GATING_ENABLE_OFFSET 0x07c > + > +/* Register bitfields in the AESS_AUTO_GATING_ENABLE__1 register */ > +#define AESS_AUTO_GATING_ENABLE_SHIFT 0 Also these should be OMAP_AESS_AUTOGATING etc, or even better, XYZ_AESS_AUTOGATING where XYZ is the type of the AESS controller. > +/** > + * aess_enable_autogating - enable AESS internal autogating > + * @oh: struct omap_hwmod * > + * > + * Enable internal autogating on the AESS. This allows the AESS to > + * indicate that it is idle to the OMAP PRCM. Returns 0. > + */ > +static void aess_enable_autogating(void __iomem *base) > +{ > + u32 v; > + > + /* Set AESS_AUTO_GATING_ENABLE__1.ENABLE to allow idle entry */ > + v = 1 << AESS_AUTO_GATING_ENABLE_SHIFT; > + writel(v, base + AESS_AUTO_GATING_ENABLE_OFFSET); > +} This should be static inline function as it's in the header, and again something like omap_aess_enable_autogating. > +/** > + * hwmod_aess_preprogram - enable AESS internal autogating (called by hwmod) > + * @oh: struct omap_hwmod * > + * > + * The AESS will not IdleAck to the PRCM until its internal autogating > + * is enabled. Since internal autogating is disabled by default after > + * AESS reset, we must enable autogating after the hwmod code resets > + * the AESS. Returns 0. > + */ > +static int __maybe_unused hwmod_aess_preprogram(struct omap_hwmod *oh) > +{ > + void __iomem *va; > + > + va = omap_hwmod_get_mpu_rt_va(oh); > + if (!va) > + return -EINVAL; > + > + aess_enable_autogating(va); > + > + return 0; > +} Then this function should not be in this header, instead it should be a static function somewhere in the omap hwmod code in some .c file. That's because this header should only have omap aess specific driver code, no hwmod code should be needed here. Regards, Tony
WARNING: multiple messages have this Message-ID (diff)
From: tony@atomide.com (Tony Lindgren) To: linux-arm-kernel@lists.infradead.org Subject: [PATCHv2 07/12] ARM: OMAP4+: AESS: enable internal auto-gating during initial setup Date: Sun, 10 Jun 2012 23:29:06 -0700 [thread overview] Message-ID: <20120611062905.GS12766@atomide.com> (raw) In-Reply-To: <20120611004611.20034.60143.stgit@dusk> Hi, Few comments below on making the platform_data work better along with other archs. * Paul Walmsley <paul@pwsan.com> [120610 17:56]: > Enable the AESS auto-gating control bit during AESS hwmod setup. This > fixes the following boot warning on OMAP4: ... > --- /dev/null > +++ b/include/linux/platform_data/aess.h This should be include/linux/platform_data/omap-aess.h or similar as there are other aess controllers too. > +/* > + * AESS_AUTO_GATING_ENABLE_OFFSET: offset in bytes of the AESS IP > + * block's AESS_AUTO_GATING_ENABLE__1 register from the IP block's > + * base address > + */ > +#define AESS_AUTO_GATING_ENABLE_OFFSET 0x07c > + > +/* Register bitfields in the AESS_AUTO_GATING_ENABLE__1 register */ > +#define AESS_AUTO_GATING_ENABLE_SHIFT 0 Also these should be OMAP_AESS_AUTOGATING etc, or even better, XYZ_AESS_AUTOGATING where XYZ is the type of the AESS controller. > +/** > + * aess_enable_autogating - enable AESS internal autogating > + * @oh: struct omap_hwmod * > + * > + * Enable internal autogating on the AESS. This allows the AESS to > + * indicate that it is idle to the OMAP PRCM. Returns 0. > + */ > +static void aess_enable_autogating(void __iomem *base) > +{ > + u32 v; > + > + /* Set AESS_AUTO_GATING_ENABLE__1.ENABLE to allow idle entry */ > + v = 1 << AESS_AUTO_GATING_ENABLE_SHIFT; > + writel(v, base + AESS_AUTO_GATING_ENABLE_OFFSET); > +} This should be static inline function as it's in the header, and again something like omap_aess_enable_autogating. > +/** > + * hwmod_aess_preprogram - enable AESS internal autogating (called by hwmod) > + * @oh: struct omap_hwmod * > + * > + * The AESS will not IdleAck to the PRCM until its internal autogating > + * is enabled. Since internal autogating is disabled by default after > + * AESS reset, we must enable autogating after the hwmod code resets > + * the AESS. Returns 0. > + */ > +static int __maybe_unused hwmod_aess_preprogram(struct omap_hwmod *oh) > +{ > + void __iomem *va; > + > + va = omap_hwmod_get_mpu_rt_va(oh); > + if (!va) > + return -EINVAL; > + > + aess_enable_autogating(va); > + > + return 0; > +} Then this function should not be in this header, instead it should be a static function somewhere in the omap hwmod code in some .c file. That's because this header should only have omap aess specific driver code, no hwmod code should be needed here. Regards, Tony
next prev parent reply other threads:[~2012-06-11 6:29 UTC|newest] Thread overview: 106+ messages / expand[flat|nested] mbox.gz Atom feed top 2012-06-11 0:45 [PATCHv2 00/12] ARM: OMAP: core/hwmod: first set of fixes for 3.5-rc Paul Walmsley 2012-06-11 0:45 ` Paul Walmsley 2012-06-11 0:45 ` [PATCHv2 01/12] ARM: OMAP: PM: Lock clocks list while generating summary Paul Walmsley 2012-06-11 0:45 ` Paul Walmsley 2012-06-11 0:45 ` [PATCHv2 02/12] ARM: OMAP2+: hwmod code/data: fix 32K sync timer Paul Walmsley 2012-06-11 0:45 ` Paul Walmsley 2012-06-14 16:47 ` Cousson, Benoit 2012-06-14 16:47 ` Cousson, Benoit 2012-06-14 18:04 ` Paul Walmsley 2012-06-14 18:04 ` Paul Walmsley 2012-06-14 20:13 ` Cousson, Benoit 2012-06-14 20:13 ` Cousson, Benoit 2012-06-15 0:18 ` Paul Walmsley 2012-06-15 0:18 ` Paul Walmsley 2012-06-15 13:28 ` Cousson, Benoit 2012-06-15 13:28 ` Cousson, Benoit 2012-07-04 12:48 ` Paul Walmsley 2012-07-04 12:48 ` Paul Walmsley 2012-07-04 12:53 ` Paul Walmsley 2012-07-04 12:53 ` Paul Walmsley 2012-07-04 14:27 ` Kevin Hilman 2012-07-04 14:27 ` Kevin Hilman 2012-07-04 14:53 ` Paul Walmsley 2012-07-04 14:53 ` Paul Walmsley 2012-07-04 16:14 ` Benoit Cousson 2012-07-04 16:14 ` Benoit Cousson 2012-07-04 16:41 ` Tero Kristo 2012-07-04 16:41 ` Tero Kristo 2012-07-04 16:43 ` Benoit Cousson 2012-07-04 16:43 ` Benoit Cousson 2012-07-04 19:02 ` Paul Walmsley 2012-07-04 19:02 ` Paul Walmsley 2012-07-04 16:57 ` Benoit Cousson 2012-07-04 16:57 ` Benoit Cousson 2012-07-04 18:59 ` Paul Walmsley 2012-07-04 18:59 ` Paul Walmsley 2012-07-05 22:06 ` Kevin Hilman 2012-07-05 22:06 ` Kevin Hilman 2012-07-04 16:01 ` Benoit Cousson 2012-07-04 16:01 ` Benoit Cousson 2012-07-04 19:05 ` Paul Walmsley 2012-07-04 19:05 ` Paul Walmsley 2012-06-11 0:46 ` [PATCHv2 03/12] ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 0:46 ` [PATCHv2 04/12] ARM: OMAP4: hwmod data: fix 32k sync timer idle modes Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 9:31 ` Cousson, Benoit 2012-06-11 9:31 ` Cousson, Benoit 2012-06-13 17:22 ` Paul Walmsley 2012-06-13 17:22 ` Paul Walmsley 2012-06-11 0:46 ` [PATCHv2 05/12] ARM: OMAP2+: hwmod: add setup_preprogram hook Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 0:46 ` [PATCHv2 06/12] ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 0:46 ` [PATCHv2 07/12] ARM: OMAP4+: AESS: enable internal auto-gating during initial setup Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 6:29 ` Tony Lindgren [this message] 2012-06-11 6:29 ` Tony Lindgren 2012-06-14 9:49 ` Paul Walmsley 2012-06-14 9:49 ` Paul Walmsley 2012-06-14 9:59 ` Tony Lindgren 2012-06-14 9:59 ` Tony Lindgren 2012-06-11 0:46 ` [PATCHv2 08/12] ARM: OMAP4: hwmod data: add SL2IF hardreset line Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-14 12:55 ` Cousson, Benoit 2012-06-14 12:55 ` Cousson, Benoit 2012-06-14 17:09 ` Paul Walmsley 2012-06-14 17:09 ` Paul Walmsley 2012-06-14 21:07 ` Cousson, Benoit 2012-06-14 21:07 ` Cousson, Benoit 2012-06-14 23:02 ` Paul Walmsley 2012-06-14 23:02 ` Paul Walmsley 2012-06-15 9:11 ` Cousson, Benoit 2012-06-15 9:11 ` Cousson, Benoit 2012-06-11 0:46 ` [PATCHv2 09/12] ARM: OMAP2+: usb_host_fs: add custom setup_preprogram for usb_host_fs (fsusb) Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 6:34 ` Tony Lindgren 2012-06-11 6:34 ` Tony Lindgren 2012-06-11 7:13 ` Felipe Balbi 2012-06-11 7:13 ` Felipe Balbi 2012-06-11 7:41 ` Tony Lindgren 2012-06-11 7:41 ` Tony Lindgren 2012-06-11 7:48 ` Felipe Balbi 2012-06-11 7:48 ` Felipe Balbi 2012-06-11 8:03 ` Tony Lindgren 2012-06-11 8:03 ` Tony Lindgren 2012-06-11 9:12 ` Felipe Balbi 2012-06-11 9:12 ` Felipe Balbi 2012-06-11 0:46 ` [PATCHv2 10/12] ARM: OMAP2+: CM: increase the module disable timeout Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 0:46 ` [PATCHv2 11/12] ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 16:28 ` Cousson, Benoit 2012-06-11 16:28 ` Cousson, Benoit 2012-06-11 16:59 ` Paul Walmsley 2012-06-11 16:59 ` Paul Walmsley 2012-06-11 20:15 ` Cousson, Benoit 2012-06-11 20:15 ` Cousson, Benoit 2012-06-11 0:46 ` [PATCHv2 12/12] ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init Paul Walmsley 2012-06-11 0:46 ` Paul Walmsley 2012-06-11 9:54 ` Cousson, Benoit 2012-06-11 9:54 ` Cousson, Benoit 2012-10-30 4:05 ` Paul Walmsley 2012-10-30 4:05 ` Paul Walmsley 2012-10-30 7:41 ` Péter Ujfalusi 2012-10-30 7:41 ` Péter Ujfalusi
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20120611062905.GS12766@atomide.com \ --to=tony@atomide.com \ --cc=b-cousson@ti.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-omap@vger.kernel.org \ --cc=paul@pwsan.com \ --cc=peter.ujfalusi@ti.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.