* [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe Hello This patch series add the driver for sun8i-emac which handle the Ethernet MAC present on Allwinner H3/A83T/A64 SoCs. It supports 10/100/1000 Mbit/s speed with half/full duplex. It can use an internal PHY (MII 10/100) or an external PHY via RGMII/RMII. This patch series enable the driver only for the H3 SoC since A83T and A64 doesn't have the necessary clocks present in mainline. This patch series enable the driver only for OrangePiPC and OrangePIOne boards since other board with H3 use external PHY which need optional regulators that will be supported later. The driver have been tested on the following boards: - H3 Orange PI PC, Orange PI Plus, BananaPI-M2+ - A64 Pine64 - A83T BananaPI-M3 I would like to thanks Chen-Yu Tsai for his help on developing this driver. Regards Changes since v2 - Added patch to support Orange PI One - Added a patch to enable SUN8I_EMAC in sunxi_defconfig - Added a patch to enable pm_runtime - The Emac clock is now used standard syscon/regmap - Added netdev_sent_queue/netdev_completed_queue - Added lots of documentation on working (locks, memory barrier, etc...) - Cleaned DT bindings documentation - Added ethernet0 aliases as suggested by Hans de Goede - Change prefix of all DEFINE to EMAC_ - The driver is now endian safe - Reworked the internal PHY mechanism - Removed dma_set_mask_and_coherent(32) since it is the default for of_platform_driver Changes since v1 - Implement NAPI - Sorted and reworded all define - Reworked ethtools stats strings - Removed all unneeded __packked and __aligned - Added tuning of RX/TX ring size via ethtool - Corrected use of sk/skb naming - Added some wmb when needed - Moved irq claim/free to emac_open/close - Lots of code refactoring Corentin Labbe (8): ethernet: sun8i-emac: add pm_runtime support ethernet: add sun8i-emac driver MAINTAINERS: Add myself as maintainer of sun8i-emac ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac ARM: dts: sun8i-h3: Add dt node for the syscon control module ARM: dts: sun8i-h3: add sun8i-emac ethernet driver ARM: dts: sun8i: Enable sun8i-emac on the Orange PI PC ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig Hans de Goede (1): ARM: dts: sun8i: Enable sun8i-emac on the Orange PI One .../bindings/net/allwinner,sun8i-emac.txt | 64 + MAINTAINERS | 6 + arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 10 + arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 10 + arch/arm/boot/dts/sun8i-h3.dtsi | 24 + arch/arm/configs/sunxi_defconfig | 1 + drivers/net/ethernet/allwinner/Kconfig | 13 + drivers/net/ethernet/allwinner/Makefile | 1 + drivers/net/ethernet/allwinner/sun8i-emac.c | 2313 ++++++++++++++++++++ 9 files changed, 2442 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt create mode 100644 drivers/net/ethernet/allwinner/sun8i-emac.c -- 2.7.3 ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel Hello This patch series add the driver for sun8i-emac which handle the Ethernet MAC present on Allwinner H3/A83T/A64 SoCs. It supports 10/100/1000 Mbit/s speed with half/full duplex. It can use an internal PHY (MII 10/100) or an external PHY via RGMII/RMII. This patch series enable the driver only for the H3 SoC since A83T and A64 doesn't have the necessary clocks present in mainline. This patch series enable the driver only for OrangePiPC and OrangePIOne boards since other board with H3 use external PHY which need optional regulators that will be supported later. The driver have been tested on the following boards: - H3 Orange PI PC, Orange PI Plus, BananaPI-M2+ - A64 Pine64 - A83T BananaPI-M3 I would like to thanks Chen-Yu Tsai for his help on developing this driver. Regards Changes since v2 - Added patch to support Orange PI One - Added a patch to enable SUN8I_EMAC in sunxi_defconfig - Added a patch to enable pm_runtime - The Emac clock is now used standard syscon/regmap - Added netdev_sent_queue/netdev_completed_queue - Added lots of documentation on working (locks, memory barrier, etc...) - Cleaned DT bindings documentation - Added ethernet0 aliases as suggested by Hans de Goede - Change prefix of all DEFINE to EMAC_ - The driver is now endian safe - Reworked the internal PHY mechanism - Removed dma_set_mask_and_coherent(32) since it is the default for of_platform_driver Changes since v1 - Implement NAPI - Sorted and reworded all define - Reworked ethtools stats strings - Removed all unneeded __packked and __aligned - Added tuning of RX/TX ring size via ethtool - Corrected use of sk/skb naming - Added some wmb when needed - Moved irq claim/free to emac_open/close - Lots of code refactoring Corentin Labbe (8): ethernet: sun8i-emac: add pm_runtime support ethernet: add sun8i-emac driver MAINTAINERS: Add myself as maintainer of sun8i-emac ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac ARM: dts: sun8i-h3: Add dt node for the syscon control module ARM: dts: sun8i-h3: add sun8i-emac ethernet driver ARM: dts: sun8i: Enable sun8i-emac on the Orange PI PC ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig Hans de Goede (1): ARM: dts: sun8i: Enable sun8i-emac on the Orange PI One .../bindings/net/allwinner,sun8i-emac.txt | 64 + MAINTAINERS | 6 + arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 10 + arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 10 + arch/arm/boot/dts/sun8i-h3.dtsi | 24 + arch/arm/configs/sunxi_defconfig | 1 + drivers/net/ethernet/allwinner/Kconfig | 13 + drivers/net/ethernet/allwinner/Makefile | 1 + drivers/net/ethernet/allwinner/sun8i-emac.c | 2313 ++++++++++++++++++++ 9 files changed, 2442 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt create mode 100644 drivers/net/ethernet/allwinner/sun8i-emac.c -- 2.7.3 ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 1/9] ethernet: add sun8i-emac driver 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe This patch add support for sun8i-emac ethernet MAC hardware. It could be found in Allwinner H3/A83T/A64 SoCs. It supports 10/100/1000 Mbit/s speed with half/full duplex. It can use an internal PHY (MII 10/100) or an external PHY via RGMII/RMII. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- drivers/net/ethernet/allwinner/Kconfig | 13 + drivers/net/ethernet/allwinner/Makefile | 1 + drivers/net/ethernet/allwinner/sun8i-emac.c | 2255 +++++++++++++++++++++++++++ 3 files changed, 2269 insertions(+) create mode 100644 drivers/net/ethernet/allwinner/sun8i-emac.c diff --git a/drivers/net/ethernet/allwinner/Kconfig b/drivers/net/ethernet/allwinner/Kconfig index 47da7e7..060569c 100644 --- a/drivers/net/ethernet/allwinner/Kconfig +++ b/drivers/net/ethernet/allwinner/Kconfig @@ -33,4 +33,17 @@ config SUN4I_EMAC To compile this driver as a module, choose M here. The module will be called sun4i-emac. +config SUN8I_EMAC + tristate "Allwinner sun8i EMAC support" + depends on ARCH_SUNXI || COMPILE_TEST + depends on OF + select MII + select PHYLIB + ---help--- + This driver support the sun8i EMAC ethernet driver present on + H3/A83T/A64 Allwinner SoCs. + + To compile this driver as a module, choose M here. The module + will be called sun8i-emac. + endif # NET_VENDOR_ALLWINNER diff --git a/drivers/net/ethernet/allwinner/Makefile b/drivers/net/ethernet/allwinner/Makefile index 03129f7..8bd1693c 100644 --- a/drivers/net/ethernet/allwinner/Makefile +++ b/drivers/net/ethernet/allwinner/Makefile @@ -3,3 +3,4 @@ # obj-$(CONFIG_SUN4I_EMAC) += sun4i-emac.o +obj-$(CONFIG_SUN8I_EMAC) += sun8i-emac.o diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c new file mode 100644 index 0000000..1c4bc80 --- /dev/null +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c @@ -0,0 +1,2255 @@ +/* + * sun8i-emac driver + * + * Copyright (C) 2015-2016 Corentin LABBE <clabbe.montjoie@gmail.com> + * + * This is the driver for Allwinner Ethernet MAC found in H3/A83T/A64 SoC + * + * TODO: + * - MAC filtering + * - Jumbo frame + * - features rx-all (NETIF_F_RXALL_BIT) + * - PM runtime + */ +#include <linux/bitops.h> +#include <linux/clk.h> +#include <linux/dma-mapping.h> +#include <linux/etherdevice.h> +#include <linux/interrupt.h> +#include <linux/iopoll.h> +#include <linux/mii.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/of_device.h> +#include <linux/of_mdio.h> +#include <linux/of_net.h> +#include <linux/phy.h> +#include <linux/pinctrl/consumer.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/scatterlist.h> +#include <linux/skbuff.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> + +#define EMAC_BASIC_CTL0 0x00 +#define EMAC_BASIC_CTL1 0x04 +#define EMAC_INT_STA 0x08 +#define EMAC_INT_EN 0x0C +#define EMAC_TX_CTL0 0x10 +#define EMAC_TX_CTL1 0x14 +#define EMAC_TX_FLOW_CTL 0x1C +#define EMAC_RX_CTL0 0x24 +#define EMAC_RX_CTL1 0x28 +#define EMAC_RX_FRM_FLT 0x38 +#define EMAC_MDIO_CMD 0x48 +#define EMAC_MDIO_DATA 0x4C +#define EMAC_TX_DMA_STA 0xB0 +#define EMAC_TX_CUR_DESC 0xB4 +#define EMAC_TX_CUR_BUF 0xB8 +#define EMAC_RX_DMA_STA 0xC0 + +#define MDIO_CMD_MII_BUSY BIT(0) +#define MDIO_CMD_MII_WRITE BIT(1) +#define MDIO_CMD_MII_PHY_REG_ADDR_MASK GENMASK(8, 4) +#define MDIO_CMD_MII_PHY_REG_ADDR_SHIFT 4 +#define MDIO_CMD_MII_PHY_ADDR_MASK GENMASK(16, 12) +#define MDIO_CMD_MII_PHY_ADDR_SHIFT 12 + +#define EMAC_MACADDR_HI 0x50 +#define EMAC_MACADDR_LO 0x54 + +#define EMAC_RX_DESC_LIST 0x34 +#define EMAC_TX_DESC_LIST 0x20 + +#define EMAC_RX_DO_CRC BIT(27) +#define EMAC_RX_STRIP_FCS BIT(28) + +#define LE32_BIT(x) (cpu_to_le32(BIT(x))) + +#define EMAC_COULD_BE_USED_BY_DMA LE32_BIT(31) + +/* Used in RX_CTL1*/ +#define EMAC_RX_DMA_EN BIT(30) +#define EMAC_RX_DMA_START BIT(31) +/* Used in TX_CTL1*/ +#define EMAC_TX_DMA_EN BIT(30) +#define EMAC_TX_DMA_START BIT(31) + +/* Used in RX_CTL0 */ +#define EMAC_RX_RECEIVER_EN BIT(31) +/* Used in TX_CTL0 */ +#define EMAC_TX_TRANSMITTER_EN BIT(31) + +/* Basic CTL0 */ +#define EMAC_BCTL0_FD BIT(0) +#define EMAC_BCTL0_SPEED_10 2 +#define EMAC_BCTL0_SPEED_100 3 +#define EMAC_BCTL0_SPEED_MASK GENMASK(3, 2) +#define EMAC_BCTL0_SPEED_SHIFT 2 + +#define EMAC_FLOW_RX 1 +#define EMAC_FLOW_TX 2 + +#define EMAC_TX_INT BIT(0) +#define EMAC_TX_DMA_STOP_INT BIT(1) +#define EMAC_TX_BUF_UA_INT BIT(2) +#define EMAC_TX_TIMEOUT_INT BIT(3) +#define EMAC_TX_UNDERFLOW_INT BIT(4) +#define EMAC_TX_EARLY_INT BIT(5) +#define EMAC_RX_INT BIT(8) +#define EMAC_RX_BUF_UA_INT BIT(9) +#define EMAC_RX_DMA_STOP_INT BIT(10) +#define EMAC_RX_TIMEOUT_INT BIT(11) +#define EMAC_RX_OVERFLOW_INT BIT(12) +#define EMAC_RX_EARLY_INT BIT(13) +#define EMAC_RGMII_STA_INT BIT(16) + +/* Bits used in frame RX status */ +#define EMAC_DSC_RX_FIRST BIT(9) +#define EMAC_DSC_RX_LAST BIT(8) + +/* Bits used in frame TX ctl */ +#define EMAC_MAGIC_TX_BIT LE32_BIT(24) +#define EMAC_TX_DO_CRC (LE32_BIT(27) | LE32_BIT(28)) +#define EMAC_DSC_TX_FIRST LE32_BIT(29) +#define EMAC_DSC_TX_LAST LE32_BIT(30) +#define EMAC_WANT_INT LE32_BIT(31) + +/* struct emac_variant - Describe an emac variant of sun8i-emac + * @default_syscon_value: Default value of the syscon EMAC register + * The default_syscon_value is also used for powering down the PHY + * @internal_phy: which PHY type is internal + * @support_mii: Does the SoC support MII + * @support_rmii: Does the SoC support RMII + * @support_rgmii: Does the SoC support RGMII + */ +struct emac_variant { + u32 default_syscon_value; + int internal_phy; + bool support_mii; + bool support_rmii; + bool support_rgmii; +}; + +static const struct emac_variant emac_variant_h3 = { + .default_syscon_value = 0x58000, + .internal_phy = PHY_INTERFACE_MODE_MII, + .support_mii = true, + .support_rmii = true, + .support_rgmii = true +}; + +static const struct emac_variant emac_variant_a83t = { + .default_syscon_value = 0, + .internal_phy = 0, + .support_mii = true, + .support_rgmii = true +}; + +static const struct emac_variant emac_variant_a64 = { + .default_syscon_value = 0, + .internal_phy = 0, + .support_mii = true, + .support_rmii = true, + .support_rgmii = true +}; + +static const char const estats_str[][ETH_GSTRING_LEN] = { + /* errors */ + "rx_payload_error", + "rx_CRC_error", + "rx_phy_error", + "rx_length_error", + "rx_col_error", + "rx_header_error", + "rx_overflow_error", + "rx_saf_error", + "rx_daf_error", + "rx_buf_error", + "rx_invalid_error", + "tx_timeout", + /* misc infos */ + "tx_stop_queue", + "rx_dma_ua", + "rx_dma_stop", + "tx_dma_ua", + "tx_dma_stop", + "rx_hw_csum", + "tx_hw_csum", + /* interrupts */ + "rx_int", + "tx_int", + "tx_early_int", + "tx_underflow_int", + "tx_timeout_int", + "rx_early_int", + "rx_overflow_int", + "rx_timeout_int", + "rgmii_state_int", + /* debug */ + "tx_used_desc", + "napi_schedule", + "napi_underflow", +}; + +struct sun8i_emac_stats { + u64 rx_payload_error; + u64 rx_crc_error; + u64 rx_phy_error; + u64 rx_length_error; + u64 rx_col_error; + u64 rx_header_error; + u64 rx_overflow_error; + u64 rx_saf_fail; + u64 rx_daf_fail; + u64 rx_buf_error; + u64 rx_invalid_error; + u64 tx_timeout; + + u64 tx_stop_queue; + u64 rx_dma_ua; + u64 rx_dma_stop; + u64 tx_dma_ua; + u64 tx_dma_stop; + u64 rx_hw_csum; + u64 tx_hw_csum; + + u64 rx_int; + u64 tx_int; + u64 tx_early_int; + u64 tx_underflow_int; + u64 tx_timeout_int; + u64 rx_early_int; + u64 rx_overflow_int; + u64 rx_timeout_int; + u64 rgmii_state_int; + + u64 tx_used_desc; + u64 napi_schedule; + u64 napi_underflow; +}; + +/* The datasheet said that each descriptor can transfers up to 4096bytes + * But latter, a register documentation reduce that value to 2048 + * Anyway using 2048 cause strange behaviours and even BSP driver use 2047 + */ +#define DESC_BUF_MAX 2044 + +/* MAGIC value for knowing if a descriptor is available or not */ +#define DCLEAN cpu_to_le32(BIT(16) | BIT(14) | BIT(12) | BIT(10) | BIT(9)) + +/* struct dma_desc - Structure of DMA descriptor used by the hardware + * @status: Status of the frame written by HW, so RO for the + * driver (except for BIT(31) which is R/W) + * @ctl: Information on the frame written by the driver (INT, len,...) + * @buf_addr: physical address of the frame data + * @next: physical address of next dma_desc + */ +struct dma_desc { + __le32 status; + __le32 ctl; + __le32 buf_addr; + __le32 next; +}; + +/* Describe how data from skb are DMA mapped (used in txinfo map member) */ +#define MAP_SINGLE 1 +#define MAP_PAGE 2 + +/* Structure for storing information about data in TX ring buffer */ +struct txinfo { + struct sk_buff *skb; + int map; +}; + +struct sun8i_emac_priv { + void __iomem *base; + struct regmap *regmap; + int irq; + struct device *dev; + struct net_device *ndev; + struct mii_bus *mdio; + struct napi_struct napi; + spinlock_t tx_lock;/* control the access of transmit descriptors */ + int duplex; + int speed; + int link; + int phy_interface; + const struct emac_variant *variant; + struct device_node *phy_node; + struct clk *ahb_clk; + struct clk *ephy_clk; + bool use_internal_phy; + + struct reset_control *rst_mac; + struct reset_control *rst_ephy; + + struct dma_desc *dd_rx; + dma_addr_t dd_rx_phy; + struct dma_desc *dd_tx; + dma_addr_t dd_tx_phy; + struct sk_buff **rx_skb; + struct txinfo *txl; + + int nbdesc_tx; + int nbdesc_rx; + int tx_slot; + int tx_dirty; + int rx_dirty; + struct sun8i_emac_stats estats; + u32 msg_enable; + int flow_ctrl; + int pause; +}; + +static irqreturn_t sun8i_emac_dma_interrupt(int irq, void *dev_id); + +static void rb_inc(int *p, const int max) +{ + (*p)++; + (*p) %= max; +} + +/* Locking strategy: + * RX queue does not need any lock since only sun8i_emac_poll() access it. + * (All other RX modifiers (ringparam/ndo_stop) disable NAPI and so + * sun8i_emac_poll()) + * TX queue is handled by sun8i_emac_xmit(), sun8i_emac_complete_xmit() and + * sun8i_emac_tx_timeout() + * (All other RX modifiers (ringparam/ndo_stop) disable NAPI and stop queue) + * + * sun8i_emac_xmit() could fire only once (netif_tx_lock) + * sun8i_emac_complete_xmit() could fire only once (called from NAPI) + * sun8i_emac_tx_timeout() could fire only once (netif_tx_lock) and could not + * race with sun8i_emac_xmit (due to netif_tx_lock) and with + * sun8i_emac_complete_xmit which disable NAPI. + * + * So only sun8i_emac_xmit and sun8i_emac_complete_xmit could fire at the same + * time. + * But they never could modify the same descriptors: + * - sun8i_emac_complete_xmit() will modify only descriptors with empty status + * - sun8i_emac_xmit() will modify only descriptors set to DCLEAN + * Proper memory barriers ensure that descriptor set to DCLEAN could not be + * modified latter by sun8i_emac_complete_xmit(). + */ + +/* Return the number of contiguous free descriptors + * starting from tx_slot + */ +static int rb_tx_numfreedesc(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + if (priv->tx_slot < priv->tx_dirty) + return priv->tx_dirty - priv->tx_slot; + + return (priv->nbdesc_tx - priv->tx_slot) + priv->tx_dirty; +} + +/* sun8i_emac_rx_skb - Allocate a skb in a DMA descriptor + * + * @ndev: The net_device for this interface + * @i: index of slot to fill + * + * Refill a DMA descriptor with a fresh skb and map it for DMA. +*/ +static int sun8i_emac_rx_skb(struct net_device *ndev, int i) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + struct sk_buff *skb; + + ddesc = priv->dd_rx + i; + + ddesc->ctl = 0; + + skb = netdev_alloc_skb_ip_align(ndev, DESC_BUF_MAX); + if (!skb) + return -ENOMEM; + + /* should not happen */ + if (unlikely(priv->rx_skb[i])) + dev_warn(priv->dev, "BUG: Leaking a skbuff\n"); + + priv->rx_skb[i] = skb; + + ddesc->buf_addr = dma_map_single(priv->dev, skb->data, + DESC_BUF_MAX, DMA_FROM_DEVICE); + if (dma_mapping_error(priv->dev, ddesc->buf_addr)) { + dev_err(priv->dev, "ERROR: Cannot map RX buffer for DMA\n"); + dev_kfree_skb(skb); + return -EFAULT; + } + /* We cannot direcly use cpu_to_le32() after dma_map_single + * since dma_mapping_error use it + */ + ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr); + ddesc->ctl |= cpu_to_le32(DESC_BUF_MAX); + /* EMAC_COULD_BE_USED_BY_DMA must be the last value written */ + wmb(); + ddesc->status = EMAC_COULD_BE_USED_BY_DMA; + + return 0; +} + +static void sun8i_emac_stop_tx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + netif_stop_queue(ndev); + + v = readl(priv->base + EMAC_TX_CTL0); + /* Disable transmitter after current reception */ + v &= ~EMAC_TX_TRANSMITTER_EN; + writel(v, priv->base + EMAC_TX_CTL0); + + v = readl(priv->base + EMAC_TX_CTL1); + /* Stop TX DMA */ + v &= ~EMAC_TX_DMA_EN; + writel(v, priv->base + EMAC_TX_CTL1); + + /* We must be sure that all is stopped before leaving this function */ + wmb(); +} + +static void sun8i_emac_stop_rx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_RX_CTL0); + /* Disable receiver after current reception */ + v &= ~EMAC_RX_RECEIVER_EN; + writel(v, priv->base + EMAC_RX_CTL0); + + v = readl(priv->base + EMAC_RX_CTL1); + /* Stop RX DMA */ + v &= ~EMAC_RX_DMA_EN; + writel(v, priv->base + EMAC_RX_CTL1); + + /* We must be sure that all is stopped before leaving this function */ + wmb(); +} + +static void sun8i_emac_start_rx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_RX_CTL0); + /* Enable receiver */ + v |= EMAC_RX_RECEIVER_EN; + writel(v, priv->base + EMAC_RX_CTL0); + + v = readl(priv->base + EMAC_RX_CTL1); + v |= EMAC_RX_DMA_START; + v |= EMAC_RX_DMA_EN; + writel(v, priv->base + EMAC_RX_CTL1); +} + +static void sun8i_emac_start_tx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_TX_CTL0); + v |= EMAC_TX_TRANSMITTER_EN; + writel(v, priv->base + EMAC_TX_CTL0); + + v = readl(priv->base + EMAC_TX_CTL1); + v |= EMAC_TX_DMA_START; + v |= EMAC_TX_DMA_EN; + writel(v, priv->base + EMAC_TX_CTL1); +} + +/* sun8i_emac_set_macaddr - Set MAC address for slot index + * + * @addr: the MAC address to set + * @index: The index of slot where to set address. + * + * The slot 0 is the main MAC address + */ +static void sun8i_emac_set_macaddr(struct sun8i_emac_priv *priv, + const u8 *addr, int index) +{ + u32 v; + + dev_info(priv->dev, "device MAC address slot %d %pM", index, addr); + + v = (addr[5] << 8) | addr[4]; + writel(v, priv->base + EMAC_MACADDR_HI + index * 8); + + v = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0]; + writel(v, priv->base + EMAC_MACADDR_LO + index * 8); +} + +static void sun8i_emac_set_link_mode(struct sun8i_emac_priv *priv) +{ + u32 v; + + v = readl(priv->base + EMAC_BASIC_CTL0); + + if (priv->duplex) + v |= EMAC_BCTL0_FD; + else + v &= ~EMAC_BCTL0_FD; + + v &= ~EMAC_BCTL0_SPEED_MASK; + + switch (priv->speed) { + case 1000: + break; + case 100: + v |= EMAC_BCTL0_SPEED_100 << EMAC_BCTL0_SPEED_SHIFT; + break; + case 10: + v |= EMAC_BCTL0_SPEED_10 << EMAC_BCTL0_SPEED_SHIFT; + break; + default: + dev_err(priv->dev, "Unsupported speed %d\n", priv->speed); + return; + } + + writel(v, priv->base + EMAC_BASIC_CTL0); +} + +static void sun8i_emac_flow_ctrl(struct sun8i_emac_priv *priv, int duplex, + int fc) +{ + u32 flow = 0; + + flow = readl(priv->base + EMAC_RX_CTL0); + if (fc & EMAC_FLOW_RX) + flow |= BIT(16); + else + flow &= ~BIT(16); + writel(flow, priv->base + EMAC_RX_CTL0); + + flow = readl(priv->base + EMAC_TX_FLOW_CTL); + if (fc & EMAC_FLOW_TX) + flow |= BIT(0); + else + flow &= ~BIT(0); + writel(flow, priv->base + EMAC_TX_FLOW_CTL); +} + +/* Grab a frame into a skb from descriptor number i */ +static int sun8i_emac_rx_from_ddesc(struct net_device *ndev, int i) +{ + struct sk_buff *skb; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc = priv->dd_rx + i; + int frame_len; + int rxcsum_done = 0; + u32 dstatus = le32_to_cpu(ddesc->status); + + if (ndev->features & NETIF_F_RXCSUM) + rxcsum_done = 1; + + /* bit0/bit7 work only on IPv4/IPv6 TCP traffic, + * (not on ARP for example) so we do not raise rx_errors/discard frame + */ + /* the checksum or length of received frame's payload is wrong*/ + if (dstatus & BIT(0)) { + priv->estats.rx_payload_error++; + rxcsum_done = 0; + } + + /* RX_CRC_ERR */ + if (dstatus & BIT(1)) { + priv->ndev->stats.rx_errors++; + priv->ndev->stats.rx_crc_errors++; + priv->estats.rx_crc_error++; + goto discard_frame; + } + + /* RX_PHY_ERR */ + if ((dstatus & BIT(3))) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_phy_error++; + goto discard_frame; + } + + /* RX_LENGTH_ERR */ + if ((dstatus & BIT(4))) { + priv->ndev->stats.rx_errors++; + priv->ndev->stats.rx_length_errors++; + priv->estats.rx_length_error++; + goto discard_frame; + } + + /* RX_COL_ERR */ + if ((dstatus & BIT(6))) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_col_error++; + goto discard_frame; + } + + /* RX_HEADER_ERR */ + if ((dstatus & BIT(7))) { + priv->estats.rx_header_error++; + rxcsum_done = 0; + } + + /* RX_OVERFLOW_ERR */ + if ((dstatus & BIT(11))) { + priv->ndev->stats.rx_over_errors++; + priv->estats.rx_overflow_error++; + goto discard_frame; + } + + /* RX_NO_ENOUGTH_BUF_ERR */ + if ((dstatus & BIT(14))) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_buf_error++; + goto discard_frame; + } + + /* BIT(9) is for the first frame, not having it is bad since we do not + * handle Jumbo frame + */ + if ((dstatus & EMAC_DSC_RX_FIRST) == 0) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_invalid_error++; + goto discard_frame; + } + + /* this frame is not the last */ + if ((dstatus & EMAC_DSC_RX_LAST) == 0) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_invalid_error++; + goto discard_frame; + } + + frame_len = (dstatus >> 16) & 0x3FFF; + if (!(ndev->features & NETIF_F_RXFCS)) + frame_len -= ETH_FCS_LEN; + + skb = priv->rx_skb[i]; + + netif_dbg(priv, rx_status, priv->ndev, + "%s from %02d %pad len=%d status=%x st=%x\n", + __func__, i, &ddesc, frame_len, dstatus, + cpu_to_le32(ddesc->ctl)); + + skb_put(skb, frame_len); + + dma_unmap_single(priv->dev, le32_to_cpu(ddesc->buf_addr), DESC_BUF_MAX, + DMA_FROM_DEVICE); + skb->protocol = eth_type_trans(skb, priv->ndev); + if (rxcsum_done) { + skb->ip_summed = CHECKSUM_UNNECESSARY; + priv->estats.rx_hw_csum++; + } else { + skb->ip_summed = CHECKSUM_PARTIAL; + } + + priv->ndev->stats.rx_packets++; + priv->ndev->stats.rx_bytes += frame_len; + priv->rx_skb[i] = NULL; + + sun8i_emac_rx_skb(ndev, i); + napi_gro_receive(&priv->napi, skb); + + return 0; + /* If the frame need to be dropped, we simply reuse the buffer */ +discard_frame: + ddesc->ctl = cpu_to_le32(DESC_BUF_MAX); + /* EMAC_COULD_BE_USED_BY_DMA must be the last value written */ + wmb(); + ddesc->status = EMAC_COULD_BE_USED_BY_DMA; + return 0; +} + +/* Iterate over dma_desc for finding completed xmit. + * + * The problem is: how to know that a descriptor is sent and not just in + * preparation. + * Need to have status=0 and st set but this is the state of first frame just + * before setting the own-by-DMA bit. + * The solution is to used the artificial value DCLEAN. + */ +static int sun8i_emac_complete_xmit(struct net_device *ndev, int budget) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + int frame_len; + int work = 0; + unsigned int bytes_compl = 0, pkts_compl = 0; + u32 dstatus; + + do { + ddesc = priv->dd_tx + priv->tx_dirty; + + if (ddesc->status & EMAC_COULD_BE_USED_BY_DMA) + goto xmit_end; + + if (ddesc->status == DCLEAN) + goto xmit_end; + + dstatus = cpu_to_le32(ddesc->status); + + if (ddesc->status == 0 && !ddesc->ctl) { + dev_err(priv->dev, "BUG: reached the void %d %d\n", + priv->tx_dirty, priv->tx_slot); + goto xmit_end; + } + + /* TX_UNDERFLOW_ERR */ + if (dstatus & BIT(1)) + priv->ndev->stats.tx_errors++; + /* TX_DEFER_ERR */ + if (dstatus & BIT(2)) + priv->ndev->stats.tx_errors++; + /* BIT 6:3 numbers of collisions */ + if (dstatus & 0x78) + priv->ndev->stats.collisions += + (dstatus & 0x78) >> 3; + /* TX_COL_ERR_1 */ + if (dstatus & BIT(8)) + priv->ndev->stats.tx_errors++; + /* TX_COL_ERR_0 */ + if (dstatus & BIT(9)) + priv->ndev->stats.tx_errors++; + /* TX_CRS_ERR */ + if (dstatus & BIT(10)) + priv->ndev->stats.tx_carrier_errors++; + /* TX_PAYLOAD_ERR */ + if (dstatus & BIT(12)) + priv->ndev->stats.tx_errors++; + /* TX_LENGTH_ERR */ + if (dstatus & BIT(14)) + priv->ndev->stats.tx_errors++; + /* TX_HEADER_ERR */ + if (dstatus & BIT(16)) + priv->ndev->stats.tx_errors++; + + frame_len = le32_to_cpu(ddesc->ctl) & 0x3FFF; + bytes_compl += frame_len; + + if (priv->txl[priv->tx_dirty].map == MAP_SINGLE) + dma_unmap_single(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + else + dma_unmap_page(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + /* we can free skb only on last frame */ + if (priv->txl[priv->tx_dirty].skb && + (ddesc->ctl & EMAC_DSC_TX_LAST)) { + dev_kfree_skb_irq(priv->txl[priv->tx_dirty].skb); + pkts_compl++; + } + + priv->txl[priv->tx_dirty].skb = NULL; + priv->txl[priv->tx_dirty].map = 0; + ddesc->ctl = 0; + /* setting status to DCLEAN is the last value to be set */ + wmb(); + ddesc->status = DCLEAN; + work++; + + rb_inc(&priv->tx_dirty, priv->nbdesc_tx); + ddesc = priv->dd_tx + priv->tx_dirty; + } while (ddesc->ctl && + !(ddesc->status & EMAC_COULD_BE_USED_BY_DMA) && + work < budget); + +xmit_end: + netdev_completed_queue(ndev, pkts_compl, bytes_compl); + + /* if we don't have handled all packets */ + if (work < budget) + work = 0; + + if (netif_queue_stopped(ndev) && + rb_tx_numfreedesc(ndev) > MAX_SKB_FRAGS + 1) + netif_wake_queue(ndev); + return work; +} + +static int sun8i_emac_poll(struct napi_struct *napi, int budget) +{ + struct sun8i_emac_priv *priv = + container_of(napi, struct sun8i_emac_priv, napi); + struct net_device *ndev = priv->ndev; + int worked; + struct dma_desc *ddesc; + + priv->estats.napi_schedule++; + worked = sun8i_emac_complete_xmit(ndev, budget); + + ddesc = priv->dd_rx + priv->rx_dirty; + while (!(ddesc->status & EMAC_COULD_BE_USED_BY_DMA) && + worked < budget) { + sun8i_emac_rx_from_ddesc(ndev, priv->rx_dirty); + worked++; + rb_inc(&priv->rx_dirty, priv->nbdesc_rx); + ddesc = priv->dd_rx + priv->rx_dirty; + }; + if (worked < budget) { + priv->estats.napi_underflow++; + napi_complete(&priv->napi); + writel(EMAC_RX_INT | EMAC_TX_INT, priv->base + EMAC_INT_EN); + } + return worked; +} + +static int sun8i_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg) +{ + struct net_device *ndev = bus->priv; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int err; + u32 reg; + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + reg &= ~MDIO_CMD_MII_WRITE; + reg &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; + reg |= (phy_reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_REG_ADDR_MASK; + + reg &= ~MDIO_CMD_MII_PHY_ADDR_MASK; + + reg |= (phy_addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_ADDR_MASK; + + reg |= MDIO_CMD_MII_BUSY; + + writel(reg, priv->base + EMAC_MDIO_CMD); + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + return readl(priv->base + EMAC_MDIO_DATA); +} + +static int sun8i_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, + u16 data) +{ + struct net_device *ndev = bus->priv; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 reg; + int err; + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + reg &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; + reg |= (phy_reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_REG_ADDR_MASK; + + reg &= ~MDIO_CMD_MII_PHY_ADDR_MASK; + reg |= (phy_addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_ADDR_MASK; + + reg |= MDIO_CMD_MII_WRITE; + reg |= MDIO_CMD_MII_BUSY; + + writel(reg, priv->base + EMAC_MDIO_CMD); + writel(data, priv->base + EMAC_MDIO_DATA); + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + return 0; +} + +static int sun8i_emac_mdio_register(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct mii_bus *bus; + int ret; + + bus = mdiobus_alloc(); + if (!bus) { + netdev_err(ndev, "Failed to allocate a new mdio bus\n"); + return -ENOMEM; + } + + bus->name = dev_name(priv->dev); + bus->read = &sun8i_mdio_read; + bus->write = &sun8i_mdio_write; + snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%x", bus->name, priv->dev->id); + + bus->parent = priv->dev; + bus->priv = ndev; + + ret = of_mdiobus_register(bus, priv->dev->of_node); + if (ret) { + netdev_err(ndev, "Could not register a MDIO bus: %d\n", ret); + mdiobus_free(bus); + return ret; + } + + priv->mdio = bus; + + return 0; +} + +static void sun8i_emac_mdio_unregister(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + mdiobus_unregister(priv->mdio); + mdiobus_free(priv->mdio); +} + +/* Run within phydev->lock */ +static void sun8i_emac_adjust_link(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct phy_device *phydev = ndev->phydev; + int new_state = 0; + + netif_dbg(priv, link, priv->ndev, + "%s link=%x duplex=%x speed=%x\n", __func__, + phydev->link, phydev->duplex, phydev->speed); + if (!phydev) + return; + + if (phydev->link) { + if (phydev->duplex != priv->duplex) { + new_state = 1; + priv->duplex = phydev->duplex; + } + if (phydev->pause) + sun8i_emac_flow_ctrl(priv, phydev->duplex, + priv->flow_ctrl); + + if (phydev->speed != priv->speed) { + new_state = 1; + priv->speed = phydev->speed; + } + + if (priv->link == 0) { + new_state = 1; + priv->link = phydev->link; + } + + netif_dbg(priv, link, priv->ndev, + "%s new=%d link=%d pause=%d\n", + __func__, new_state, priv->link, phydev->pause); + if (new_state) + sun8i_emac_set_link_mode(priv); + } else if (priv->link != phydev->link) { + new_state = 1; + priv->link = 0; + priv->speed = 0; + priv->duplex = -1; + } + + if (new_state) + phy_print_status(phydev); +} + +/* H3 specific bits for EPHY */ +#define H3_EPHY_ADDR_SHIFT 20 +#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ +#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ +#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ + +/* H3/A64 specific bits */ +#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */ + +/* Generic system control EMAC_CLK bits */ +#define SYSCON_ETXDC_MASK GENMASK(2, 0) +#define SYSCON_ETXDC_SHIFT 10 +#define SYSCON_ERXDC_MASK GENMASK(4, 0) +#define SYSCON_ERXDC_SHIFT 5 +/* EMAC PHY Interface Type */ +#define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */ +#define SYSCON_ETCS_MASK GENMASK(1, 0) +#define SYSCON_ETCS_MII 0x0 +#define SYSCON_ETCS_EXT_GMII 0x1 +#define SYSCON_ETCS_INT_GMII 0x2 +#define SYSCON_EMAC_REG 0x30 + +static int sun8i_emac_set_syscon(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct device_node *node = priv->dev->of_node; + int ret; + u32 reg, val; + + reg = priv->variant->default_syscon_value; + + if (priv->variant->internal_phy) { + if (!priv->use_internal_phy) { + /* switch to external PHY interface */ + reg &= ~H3_EPHY_SELECT; + } else { + reg |= H3_EPHY_SELECT; + reg &= ~H3_EPHY_SHUTDOWN; + + if (of_property_read_bool(priv->phy_node, + "allwinner,leds-active-low")) + reg |= H3_EPHY_LED_POL; + + ret = of_mdio_parse_addr(priv->dev, priv->phy_node); + if (ret < 0) { + netdev_err(ndev, "Could not parse MDIO addr\n"); + return ret; + } + /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY + * address. No need to mask it again. + */ + reg |= ret << H3_EPHY_ADDR_SHIFT; + } + } + + if (!of_property_read_u32(node, "allwinner,tx-delay", &val)) { + if (val <= SYSCON_ETXDC_MASK) { + reg &= ~(SYSCON_ETXDC_MASK << SYSCON_ETXDC_SHIFT); + reg |= (val << SYSCON_ETXDC_SHIFT); + } else { + netdev_warn(ndev, "Invalid TX clock delay: %d\n", val); + } + } + + if (!of_property_read_u32(node, "allwinner,rx-delay", &val)) { + if (val <= SYSCON_ERXDC_MASK) { + reg &= ~(SYSCON_ERXDC_MASK << SYSCON_ERXDC_SHIFT); + reg |= (val << SYSCON_ERXDC_SHIFT); + } else { + netdev_warn(ndev, "Invalid RX clock delay: %d\n", val); + } + } + + /* Clear interface mode bits */ + reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT); + if (priv->variant->support_rmii) + reg &= ~SYSCON_RMII_EN; + + switch (priv->phy_interface) { + case PHY_INTERFACE_MODE_MII: + /* default */ + break; + case PHY_INTERFACE_MODE_RGMII: + reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII; + break; + case PHY_INTERFACE_MODE_RMII: + reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII; + break; + default: + netdev_err(ndev, "Unsupported interface mode: %s", + phy_modes(priv->phy_interface)); + return -EINVAL; + } + + regmap_write(priv->regmap, SYSCON_EMAC_REG, reg); + + return 0; +} + +static void sun8i_emac_unset_syscon(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 reg = priv->variant->default_syscon_value; + + regmap_write(priv->regmap, SYSCON_EMAC_REG, reg); +} + +/* Set Management Data Clock, must be call after device reset */ +static void sun8i_emac_set_mdc(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + unsigned long rate; + u32 reg; + + rate = clk_get_rate(priv->ahb_clk); + if (rate > 160000000) + reg = 0x3 << 20; /* AHB / 128 */ + else if (rate > 80000000) + reg = 0x2 << 20; /* AHB / 64 */ + else if (rate > 40000000) + reg = 0x1 << 20; /* AHB / 32 */ + else + reg = 0x0 << 20; /* AHB / 16 */ + netif_dbg(priv, link, ndev, "MDC auto : %x\n", reg); + writel(reg, priv->base + EMAC_MDIO_CMD); +} + +/* "power" the device, by enabling clk/reset/regulators */ +static int sun8i_emac_power(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int ret; + + ret = clk_prepare_enable(priv->ahb_clk); + if (ret) { + netdev_err(ndev, "Could not enable AHB clock\n"); + return ret; + } + + if (priv->rst_mac) { + ret = reset_control_deassert(priv->rst_mac); + if (ret) { + netdev_err(ndev, "Could not deassert reset\n"); + goto err_reset; + } + } + + if (priv->ephy_clk) { + ret = clk_prepare_enable(priv->ephy_clk); + if (ret) { + netdev_err(ndev, "Could not enable EPHY clock\n"); + goto err_ephy_clk; + } + } + + if (priv->rst_ephy) { + ret = reset_control_deassert(priv->rst_ephy); + if (ret) { + netdev_err(ndev, "Could not deassert EPHY reset\n"); + goto err_ephy_reset; + } + } + + return 0; + +err_ephy_reset: + if (priv->ephy_clk) + clk_disable_unprepare(priv->ephy_clk); +err_ephy_clk: + if (priv->rst_mac) + reset_control_assert(priv->rst_mac); +err_reset: + clk_disable_unprepare(priv->ahb_clk); + return ret; +} + +/* "Unpower" the device, disabling clocks and regulators, asserting reset */ +static void sun8i_emac_unpower(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + if (priv->rst_ephy) + reset_control_assert(priv->rst_ephy); + + if (priv->ephy_clk) + clk_disable_unprepare(priv->ephy_clk); + + if (priv->rst_mac) + reset_control_assert(priv->rst_mac); + + clk_disable_unprepare(priv->ahb_clk); +} + +static int sun8i_emac_init(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct device_node *node = priv->dev->of_node; + const u8 *addr; + + /* Try to get MAC address from DT, or assign a random one */ + addr = of_get_mac_address(node); + if (addr) + ether_addr_copy(ndev->dev_addr, addr); + else + eth_hw_addr_random(ndev); + + return sun8i_emac_power(ndev); +} + +static void sun8i_emac_uninit(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + mdiobus_unregister(priv->mdio); + + sun8i_emac_unpower(ndev); +} + +static int sun8i_emac_mdio_probe(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct phy_device *phydev = NULL; + + phydev = of_phy_connect(ndev, priv->phy_node, &sun8i_emac_adjust_link, + 0, priv->phy_interface); + + if (!phydev) { + netdev_err(ndev, "Could not attach to PHY\n"); + return -ENODEV; + } + + phy_attached_info(phydev); + + /* mask with MAC supported features */ + phydev->supported &= PHY_GBIT_FEATURES; + phydev->advertising = phydev->supported; + + priv->link = 0; + priv->speed = 0; + priv->duplex = -1; + + return 0; +} + +/* Allocate both RX and TX ring buffer and init them + * This function also write the startbase of thoses ring in the device. + * All structures that help managing thoses rings are also handled + * by this functions (rx_skb/txl) + */ +static int sun8i_emac_alloc_rings(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + int err, i; + + priv->rx_skb = kcalloc(priv->nbdesc_rx, sizeof(struct sk_buff *), + GFP_KERNEL); + if (!priv->rx_skb) { + err = -ENOMEM; + goto rx_skb_error; + } + priv->txl = kcalloc(priv->nbdesc_tx, sizeof(struct txinfo), GFP_KERNEL); + if (!priv->txl) { + err = -ENOMEM; + goto tx_error; + } + + /* allocate/init RX ring */ + priv->dd_rx = dma_zalloc_coherent(priv->dev, + priv->nbdesc_rx * sizeof(struct dma_desc), + &priv->dd_rx_phy, GFP_KERNEL); + if (!priv->dd_rx) { + dev_err(priv->dev, "ERROR: cannot allocate DMA RX buffer"); + err = -ENOMEM; + goto dma_rx_error; + } + ddesc = priv->dd_rx; + for (i = 0; i < priv->nbdesc_rx; i++) { + sun8i_emac_rx_skb(ndev, i); + ddesc->next = cpu_to_le32(priv->dd_rx_phy + (i + 1) + * sizeof(struct dma_desc)); + ddesc++; + } + /* last descriptor point back to first one */ + ddesc--; + ddesc->next = cpu_to_le32(priv->dd_rx_phy); + + /* allocate/init TX ring */ + priv->dd_tx = dma_zalloc_coherent(priv->dev, + priv->nbdesc_tx * sizeof(struct dma_desc), + &priv->dd_tx_phy, GFP_KERNEL); + if (!priv->dd_tx) { + dev_err(priv->dev, "ERROR: cannot allocate DMA TX buffer"); + err = -ENOMEM; + goto dma_tx_error; + } + ddesc = priv->dd_tx; + for (i = 0; i < priv->nbdesc_tx; i++) { + ddesc->status = DCLEAN; + ddesc->ctl = 0; + ddesc->next = cpu_to_le32(priv->dd_tx_phy + (i + 1) + * sizeof(struct dma_desc)); + ddesc++; + } + /* last descriptor point back to first one */ + ddesc--; + ddesc->next = cpu_to_le32(priv->dd_tx_phy); + i--; + + priv->tx_slot = 0; + priv->tx_dirty = 0; + priv->rx_dirty = 0; + + /* write start of RX ring descriptor */ + writel(priv->dd_rx_phy, priv->base + EMAC_RX_DESC_LIST); + /* write start of TX ring descriptor */ + writel(priv->dd_tx_phy, priv->base + EMAC_TX_DESC_LIST); + + return 0; +dma_tx_error: + dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc), + priv->dd_rx, priv->dd_rx_phy); +dma_rx_error: + kfree(priv->txl); +tx_error: + kfree(priv->rx_skb); +rx_skb_error: + return err; +} + +static int sun8i_emac_open(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int err; + u32 v; + + err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, + dev_name(priv->dev), ndev); + if (err) { + dev_err(priv->dev, "Cannot request IRQ: %d\n", err); + return err; + } + + /* Set interface mode (and configure internal PHY on H3) */ + err = sun8i_emac_set_syscon(ndev); + if (err) + goto err_irq; + + /* Do SOFT RST */ + v = readl(priv->base + EMAC_BASIC_CTL1); + writel(v | 0x01, priv->base + EMAC_BASIC_CTL1); + + err = readl_poll_timeout(priv->base + EMAC_BASIC_CTL1, v, + !(v & 0x01), 100, 10000); + if (err) { + dev_err(priv->dev, "EMAC reset timeout\n"); + err = -EFAULT; + goto err_syscon; + } + + sun8i_emac_set_mdc(ndev); + + err = sun8i_emac_mdio_register(ndev); + if (err) + goto err_syscon; + + err = sun8i_emac_mdio_probe(ndev); + if (err) + goto err_syscon; + + /* DMA */ + v = (8 << 24);/* burst len */ + writel(v, priv->base + EMAC_BASIC_CTL1); + + writel(EMAC_RX_INT | EMAC_TX_INT, priv->base + EMAC_INT_EN); + + v = readl(priv->base + EMAC_RX_CTL0); + /* CHECK_CRC */ + if (ndev->features & NETIF_F_RXCSUM) + v |= EMAC_RX_DO_CRC; + else + v &= ~EMAC_RX_DO_CRC; + /* STRIP_FCS */ + if (ndev->features & NETIF_F_RXFCS) + v &= ~EMAC_RX_STRIP_FCS; + else + v |= EMAC_RX_STRIP_FCS; + writel(v, priv->base + EMAC_RX_CTL0); + + v = readl(priv->base + EMAC_TX_CTL1); + /* TX_MD Transmission starts after a full frame located in TX DMA FIFO*/ + v |= BIT(1); + /* Undocumented bit (called TX_NEXT_FRM in BSP), the original comment is + * "Operating on second frame increase the performance + * especially when transmit store-and-forward is used." + */ + v |= BIT(2); + writel(v, priv->base + EMAC_TX_CTL1); + + v = readl(priv->base + EMAC_RX_CTL1); + /* RX_MD RX DMA reads data from RX DMA FIFO to host memory after a + * complete frame has been written to RX DMA FIFO + */ + v |= BIT(1); + writel(v, priv->base + EMAC_RX_CTL1); + + sun8i_emac_set_macaddr(priv, ndev->dev_addr, 0); + + err = sun8i_emac_alloc_rings(ndev); + if (err) { + netdev_err(ndev, "Fail to allocate rings\n"); + goto err_mdio; + } + + phy_start(ndev->phydev); + + sun8i_emac_start_rx(ndev); + sun8i_emac_start_tx(ndev); + + netif_napi_add(ndev, &priv->napi, sun8i_emac_poll, 64); + napi_enable(&priv->napi); + netif_start_queue(ndev); + + return 0; +err_mdio: + phy_disconnect(ndev->phydev); +err_syscon: + sun8i_emac_unset_syscon(ndev); +err_irq: + free_irq(priv->irq, ndev); + return err; +} + +/* Clean the TX ring of any accepted skb for xmit */ +static void sun8i_emac_tx_clean(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int i; + struct dma_desc *ddesc; + int frame_len; + + for (i = 0; i < priv->nbdesc_tx; i++) { + if (priv->txl[i].skb) { + ddesc = priv->dd_tx + i; + frame_len = le32_to_cpu(ddesc->ctl) & 0x3FFF; + switch (priv->txl[i].map) { + case MAP_SINGLE: + dma_unmap_single(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + break; + case MAP_PAGE: + dma_unmap_page(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + break; + default: + dev_err(priv->dev, "Trying to free an empty slot\n"); + continue; + } + dev_kfree_skb_any(priv->txl[i].skb); + priv->txl[i].skb = NULL; + ddesc->ctl = 0; + ddesc->status = DCLEAN; + } + } + priv->tx_slot = 0; + priv->tx_dirty = 0; +} + +/* Clean the RX ring */ +static void sun8i_emac_rx_clean(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int i; + struct dma_desc *ddesc; + + /* clean RX ring */ + for (i = 0; i < priv->nbdesc_rx; i++) + if (priv->rx_skb[i]) { + ddesc = priv->dd_rx + i; + dma_unmap_single(priv->dev, + le32_to_cpu(ddesc->buf_addr), + DESC_BUF_MAX, DMA_FROM_DEVICE); + dev_kfree_skb_any(priv->rx_skb[i]); + priv->rx_skb[i] = NULL; + } +} + +static int sun8i_emac_stop(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + napi_disable(&priv->napi); + + sun8i_emac_stop_tx(ndev); + sun8i_emac_stop_rx(ndev); + + phy_stop(ndev->phydev); + phy_disconnect(ndev->phydev); + + sun8i_emac_mdio_unregister(ndev); + + sun8i_emac_unset_syscon(ndev); + + free_irq(priv->irq, ndev); + + sun8i_emac_rx_clean(ndev); + sun8i_emac_tx_clean(ndev); + + kfree(priv->rx_skb); + kfree(priv->txl); + + dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc), + priv->dd_rx, priv->dd_rx_phy); + dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), + priv->dd_tx, priv->dd_tx_phy); + + return 0; +} + +static netdev_tx_t sun8i_emac_xmit(struct sk_buff *skb, struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + struct dma_desc *first; + int i = 0, rbd_first; + unsigned int len, fraglen, tlen; + u32 v; + int n; + int nf; + const skb_frag_t *frag; + int do_csum = 0; + + if (skb_put_padto(skb, ETH_ZLEN)) + return NETDEV_TX_OK; + len = skb_headlen(skb); + + n = skb_shinfo(skb)->nr_frags; + + if (skb->ip_summed == CHECKSUM_PARTIAL) { + do_csum = 1; + priv->estats.tx_hw_csum++; + } + netif_dbg(priv, tx_queued, ndev, "%s len=%u skblen=%u %x\n", __func__, + len, skb->len, + (skb->ip_summed == CHECKSUM_PARTIAL)); + + /* check for contigous space + * We need at least 1(skb->data) + n(numfrags) + 1(one clean slot) + */ + if (rb_tx_numfreedesc(ndev) < n + 2) { + dev_err_ratelimited(priv->dev, "BUG!: TX is full %d %d\n", + priv->tx_dirty, priv->tx_slot); + netif_stop_queue(ndev); + return NETDEV_TX_BUSY; + } + i = priv->tx_slot; + + ddesc = priv->dd_tx + i; + first = priv->dd_tx + i; + rbd_first = i; + + ddesc->buf_addr = dma_map_single(priv->dev, skb->data, len, + DMA_TO_DEVICE); + if (dma_mapping_error(priv->dev, ddesc->buf_addr)) { + dev_err(priv->dev, "ERROR: Cannot map buffer for DMA\n"); + goto xmit_error; + } + /* We cannot direcly use cpu_to_le32() after dma_map_single + * since dma_mapping_error use it + */ + ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr); + priv->txl[i].map = MAP_SINGLE; + priv->txl[i].skb = skb; + + tlen = len; + ddesc->ctl = le32_to_cpu(len); + /* Undocumented bit that make it works + * Without it, packets never be sent on H3 SoC + */ + ddesc->ctl |= EMAC_MAGIC_TX_BIT; + if (do_csum) + ddesc->ctl |= EMAC_TX_DO_CRC; + + /* handle fragmented skb, one descriptor per fragment */ + for (nf = 0; nf < n; nf++) { + frag = &skb_shinfo(skb)->frags[nf]; + rb_inc(&i, priv->nbdesc_tx); + priv->txl[i].skb = skb; + ddesc = priv->dd_tx + i; + fraglen = skb_frag_size(frag); + ddesc->ctl = le32_to_cpu(fraglen); + tlen += fraglen, + ddesc->ctl |= EMAC_MAGIC_TX_BIT; + if (do_csum) + ddesc->ctl |= EMAC_TX_DO_CRC; + + ddesc->buf_addr = skb_frag_dma_map(priv->dev, frag, 0, + fraglen, DMA_TO_DEVICE); + if (dma_mapping_error(priv->dev, ddesc->buf_addr)) { + dev_err(priv->dev, "Cannot map buffer for DMA\n"); + goto xmit_error; + } + /* Cannot directly use cpu_to_le32() after skb_frag_dma_map + * since dma_mapping_error use it + */ + ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr); + priv->txl[i].map = MAP_PAGE; + ddesc->status = EMAC_COULD_BE_USED_BY_DMA; + } + + /* frame end */ + ddesc->ctl |= EMAC_DSC_TX_LAST; + /* We want an interrupt after transmission */ + ddesc->ctl |= EMAC_WANT_INT; + + rb_inc(&i, priv->nbdesc_tx); + + /* frame begin */ + first->ctl |= EMAC_DSC_TX_FIRST; + wmb();/* EMAC_COULD_BE_USED_BY_DMA must be the last value written */ + first->status = EMAC_COULD_BE_USED_BY_DMA; + priv->tx_slot = i; + + /* Trying to optimize this (recording DMA start/stop) seems + * to lead to errors. So we always start DMA. + */ + v = readl(priv->base + EMAC_TX_CTL1); + v |= EMAC_TX_DMA_START; + v |= EMAC_TX_DMA_EN; + writel_relaxed(v, priv->base + EMAC_TX_CTL1); + + netdev_sent_queue(ndev, skb->len); + + if (rb_tx_numfreedesc(ndev) < MAX_SKB_FRAGS + 1) { + netif_stop_queue(ndev); + priv->estats.tx_stop_queue++; + } + priv->estats.tx_used_desc = rb_tx_numfreedesc(ndev); + priv->ndev->stats.tx_packets++; + priv->ndev->stats.tx_bytes += tlen; + + return NETDEV_TX_OK; + +xmit_error: + /* destroy skb and return TX OK Documentation/DMA-API-HOWTO.txt */ + /* clean descritors from rbd_first to i */ + ddesc->ctl = 0; + /* setting status to DCLEAN is the last value to be set */ + wmb(); + ddesc->status = DCLEAN; + do { + ddesc = priv->dd_tx + rbd_first; + ddesc->ctl = 0; + /* setting status to DCLEAN is the last value to be set */ + wmb(); + ddesc->status = DCLEAN; + rb_inc(&rbd_first, priv->nbdesc_tx); + } while (rbd_first != i); + dev_kfree_skb_any(skb); + return NETDEV_TX_OK; +} + +static int sun8i_emac_change_mtu(struct net_device *ndev, int new_mtu) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int max_mtu; + + dev_info(priv->dev, "%s set MTU to %d\n", __func__, new_mtu); + + if (netif_running(ndev)) { + dev_err(priv->dev, "%s: must be stopped to change its MTU\n", + ndev->name); + return -EBUSY; + } + + max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN); + + if ((new_mtu < 68) || (new_mtu > max_mtu)) { + dev_err(priv->dev, "%s: invalid MTU, max MTU is: %d\n", + ndev->name, max_mtu); + return -EINVAL; + } + + ndev->mtu = new_mtu; + netdev_update_features(ndev); + return 0; +} + +static int sun8i_emac_set_features(struct net_device *ndev, + netdev_features_t features) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_BASIC_CTL0); + if (features & NETIF_F_LOOPBACK && netif_running(ndev)) { + netif_info(priv, hw, ndev, "Set loopback features"); + v |= BIT(1); + } else { + netif_info(priv, hw, ndev, "Unset loopback features"); + v &= ~BIT(1); + } + writel(v, priv->base + EMAC_BASIC_CTL0); + + v = readl(priv->base + EMAC_RX_CTL0); + if (features & NETIF_F_RXCSUM) { + v |= EMAC_RX_DO_CRC; + netif_info(priv, hw, ndev, "Doing RX CRC check by hardware"); + } else { + v &= ~EMAC_RX_DO_CRC; + netif_info(priv, hw, ndev, "No RX CRC check by hardware"); + } + if (features & NETIF_F_RXFCS) { + v &= ~EMAC_RX_STRIP_FCS; + netif_info(priv, hw, ndev, "Keep FCS"); + } else { + v |= EMAC_RX_STRIP_FCS; + netif_info(priv, hw, ndev, "Strip FCS"); + } + writel(v, priv->base + EMAC_RX_CTL0); + + netif_dbg(priv, drv, ndev, "%s %llx %x\n", __func__, features, v); + + return 0; +} + +static void sun8i_emac_set_rx_mode(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v = 0; + int i = 0; + struct netdev_hw_addr *ha; + + /* Receive all multicast frames */ + v |= BIT(16); + /* Receive all control frames */ + v |= BIT(13); + if (ndev->flags & IFF_PROMISC) + v |= BIT(1); + if (netdev_uc_count(ndev) > 7) { + v |= BIT(1); + } else { + netdev_for_each_uc_addr(ha, ndev) { + i++; + sun8i_emac_set_macaddr(priv, ha->addr, i); + } + } + writel(v, priv->base + EMAC_RX_FRM_FLT); +} + +static void sun8i_emac_tx_timeout(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + netdev_err(ndev, "%s\n", __func__); + + sun8i_emac_stop_tx(ndev); + + sun8i_emac_tx_clean(ndev); + + /* write start of the new TX ring descriptor */ + writel(priv->dd_tx_phy, priv->base + EMAC_TX_DESC_LIST); + + sun8i_emac_start_tx(ndev); + + netdev_reset_queue(ndev); + + priv->estats.tx_timeout++; + ndev->stats.tx_errors++; + netif_wake_queue(ndev); +} + +static int sun8i_emac_ioctl(struct net_device *ndev, struct ifreq *rq, int cmd) +{ + struct phy_device *phydev = ndev->phydev; + + if (!netif_running(ndev)) + return -EINVAL; + + if (!phydev) + return -ENODEV; + + return phy_mii_ioctl(phydev, rq, cmd); +} + +static int sun8i_emac_check_if_running(struct net_device *ndev) +{ + if (!netif_running(ndev)) + return -EINVAL; + return 0; +} + +static int sun8i_emac_get_sset_count(struct net_device *ndev, int sset) +{ + switch (sset) { + case ETH_SS_STATS: + return ARRAY_SIZE(estats_str); + } + return -EOPNOTSUPP; +} + +static int sun8i_emac_ethtool_get_settings(struct net_device *ndev, + struct ethtool_cmd *cmd) +{ + struct phy_device *phy = ndev->phydev; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + if (!phy) { + netdev_err(ndev, "%s: %s: PHY is not registered\n", + __func__, ndev->name); + return -ENODEV; + } + + if (!netif_running(ndev)) { + dev_err(priv->dev, "interface disabled: we cannot track link speed / duplex setting\n"); + return -EBUSY; + } + + return phy_ethtool_gset(phy, cmd); +} + +static int sun8i_emac_ethtool_set_settings(struct net_device *ndev, + struct ethtool_cmd *cmd) +{ + struct phy_device *phy = ndev->phydev; + + return phy_ethtool_sset(phy, cmd); +} + +static void sun8i_emac_ethtool_getdrvinfo(struct net_device *ndev, + struct ethtool_drvinfo *info) +{ + strlcpy(info->driver, "sun8i_emac", sizeof(info->driver)); + strcpy(info->version, "00"); + info->fw_version[0] = '\0'; +} + +static void sun8i_emac_ethtool_stats(struct net_device *ndev, + struct ethtool_stats *dummy, u64 *data) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + memcpy(data, &priv->estats, + sun8i_emac_get_sset_count(ndev, ETH_SS_STATS) * sizeof(u64)); +} + +static void sun8i_emac_ethtool_strings(struct net_device *dev, u32 stringset, + u8 *buffer) +{ + switch (stringset) { + case ETH_SS_STATS: + memcpy(buffer, &estats_str, sizeof(estats_str)); + break; + } +} + +static u32 sun8i_emac_ethtool_getmsglevel(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + return priv->msg_enable; +} + +static void sun8i_emac_ethtool_setmsglevel(struct net_device *ndev, u32 level) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + priv->msg_enable = level; +} + +static void sun8i_emac_get_pauseparam(struct net_device *ndev, + struct ethtool_pauseparam *pause) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + pause->rx_pause = 0; + pause->tx_pause = 0; + pause->autoneg = ndev->phydev->autoneg; + + if (priv->flow_ctrl & EMAC_FLOW_RX) + pause->rx_pause = 1; + if (priv->flow_ctrl & EMAC_FLOW_TX) + pause->tx_pause = 1; +} + +static int sun8i_emac_set_pauseparam(struct net_device *ndev, + struct ethtool_pauseparam *pause) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct phy_device *phy = ndev->phydev; + int new_pause = 0; + int ret = 0; + + if (pause->rx_pause) + new_pause |= EMAC_FLOW_RX; + if (pause->tx_pause) + new_pause |= EMAC_FLOW_TX; + + priv->flow_ctrl = new_pause; + phy->autoneg = pause->autoneg; + + if (phy->autoneg) { + if (netif_running(ndev)) + ret = phy_start_aneg(phy); + } else { + sun8i_emac_flow_ctrl(priv, phy->duplex, priv->flow_ctrl); + } + return ret; +} + +static void sun8i_emac_ethtool_get_ringparam(struct net_device *ndev, + struct ethtool_ringparam *ring) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + ring->rx_pending = priv->nbdesc_rx; + ring->tx_pending = priv->nbdesc_tx; +} + +static int sun8i_emac_ethtool_set_ringparam(struct net_device *ndev, + struct ethtool_ringparam *ring) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int err; + + if (ring->rx_max_pending || ring->rx_mini_max_pending || + ring->rx_jumbo_max_pending || ring->rx_mini_pending || + ring->rx_jumbo_pending || ring->tx_max_pending) + return -EINVAL; + + if (ring->tx_pending < MAX_SKB_FRAGS + 1) { + netdev_err(ndev, "The number of TX descriptors is too low"); + return -EINVAL; + } + + sun8i_emac_stop_tx(ndev); + sun8i_emac_stop_rx(ndev); + + sun8i_emac_rx_clean(ndev); + sun8i_emac_tx_clean(ndev); + + kfree(priv->rx_skb); + kfree(priv->txl); + + dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc), + priv->dd_rx, priv->dd_rx_phy); + dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), + priv->dd_tx, priv->dd_tx_phy); + + priv->nbdesc_rx = ring->rx_pending; + priv->nbdesc_tx = ring->tx_pending; + err = sun8i_emac_alloc_rings(ndev); + if (err) { + /* Fatal error, we cannot re start */ + netdev_err(ndev, "Fail to allocate rings\n"); + return -EFAULT; + } + + sun8i_emac_start_rx(ndev); + sun8i_emac_start_tx(ndev); + + netif_start_queue(ndev); + + netdev_info(ndev, "Ring Param settings: rx: %d, tx %d\n", + ring->rx_pending, ring->tx_pending); + return 0; +} + +static const struct ethtool_ops sun8i_emac_ethtool_ops = { + .begin = sun8i_emac_check_if_running, + .get_settings = sun8i_emac_ethtool_get_settings, + .set_settings = sun8i_emac_ethtool_set_settings, + .get_link = ethtool_op_get_link, + .get_pauseparam = sun8i_emac_get_pauseparam, + .set_pauseparam = sun8i_emac_set_pauseparam, + .get_ethtool_stats = sun8i_emac_ethtool_stats, + .get_strings = sun8i_emac_ethtool_strings, + .get_sset_count = sun8i_emac_get_sset_count, + .get_drvinfo = sun8i_emac_ethtool_getdrvinfo, + .get_msglevel = sun8i_emac_ethtool_getmsglevel, + .set_msglevel = sun8i_emac_ethtool_setmsglevel, + .get_ringparam = sun8i_emac_ethtool_get_ringparam, + .set_ringparam = sun8i_emac_ethtool_set_ringparam, +}; + +static const struct net_device_ops sun8i_emac_netdev_ops = { + .ndo_init = sun8i_emac_init, + .ndo_uninit = sun8i_emac_uninit, + .ndo_open = sun8i_emac_open, + .ndo_start_xmit = sun8i_emac_xmit, + .ndo_stop = sun8i_emac_stop, + .ndo_change_mtu = sun8i_emac_change_mtu, + .ndo_set_features = sun8i_emac_set_features, + .ndo_set_rx_mode = sun8i_emac_set_rx_mode, + .ndo_tx_timeout = sun8i_emac_tx_timeout, + .ndo_do_ioctl = sun8i_emac_ioctl, + .ndo_set_mac_address = eth_mac_addr, +}; + +/* No locking in this function since it is guaranteed to be run once and + * do actions only done here: + * - Scheduling NAPI + * - Stopping interrupts + * - Updating stats + * + * Even when not enabled via EMAC_INT_EN, some interrupt could fire, so we need + * to handle all of them. + * Interrupts know to fire when not enabled are: + * - EMAC_TX_DMA_STOP_INT + * - EMAC_TX_BUF_UA_INT + * - EMAC_TX_EARLY_INT + * - EMAC_RX_BUF_UA_INT + * - EMAC_RX_EARLY_INT + */ +static irqreturn_t sun8i_emac_dma_interrupt(int irq, void *dev_id) +{ + struct net_device *ndev = dev_id; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v, u; + + v = readl(priv->base + EMAC_INT_STA); + + /* When this bit is asserted, a frame transmission is completed. */ + if (v & EMAC_TX_INT) { + priv->estats.tx_int++; + writel(0, priv->base + EMAC_INT_EN); + napi_schedule(&priv->napi); + } + + /* When this bit is asserted, the TX DMA FSM is stopped. + * For the moment only a call to tx_timeout cause this interrupt + * to fire. + */ + if (v & EMAC_TX_DMA_STOP_INT) + priv->estats.tx_dma_stop++; + + /* When this asserted, the TX DMA can not acquire next TX descriptor + * and TX DMA FSM is suspended. + */ + if (v & EMAC_TX_BUF_UA_INT) { + priv->estats.tx_dma_ua++; + writel(0, priv->base + EMAC_INT_EN); + napi_schedule(&priv->napi); + } + + if (v & EMAC_TX_TIMEOUT_INT) + priv->estats.tx_timeout_int++; + + if (v & EMAC_TX_UNDERFLOW_INT) + priv->estats.tx_underflow_int++; + + /* When this bit asserted , the frame is transmitted to FIFO totally. */ + if (v & EMAC_TX_EARLY_INT) + priv->estats.tx_early_int++; + + /* When this bit is asserted, a frame reception is completed */ + if (v & EMAC_RX_INT) { + priv->estats.rx_int++; + writel(0, priv->base + EMAC_INT_EN); + napi_schedule(&priv->napi); + } + + /* When this asserted, the RX DMA can not acquire next RX descriptor + * and RX DMA FSM is suspended. + */ + if (v & EMAC_RX_BUF_UA_INT) { + u = readl(priv->base + EMAC_RX_CTL1); + writel(u | EMAC_RX_DMA_START, priv->base + EMAC_RX_CTL1); + priv->estats.rx_dma_ua++; + } + + /* Same as TX DMA STOP, but never hit it */ + if (v & EMAC_RX_DMA_STOP_INT) + priv->estats.rx_dma_stop++; + + if (v & EMAC_RX_TIMEOUT_INT) + priv->estats.rx_timeout_int++; + + if (v & EMAC_RX_OVERFLOW_INT) + priv->estats.rx_overflow_int++; + + if (v & EMAC_RX_EARLY_INT) + priv->estats.rx_early_int++; + + if (v & EMAC_RGMII_STA_INT) + priv->estats.rgmii_state_int++; + + /* the datasheet state those register as read-only + * but nothing work(freeze) without writing to it + */ + writel(v, priv->base + EMAC_INT_STA); + + return IRQ_HANDLED; +} + +static int sun8i_emac_probe(struct platform_device *pdev) +{ + struct device_node *node = pdev->dev.of_node; + struct sun8i_emac_priv *priv; + struct net_device *ndev; + struct resource *res; + int ret; + + ndev = alloc_etherdev(sizeof(*priv)); + if (!ndev) + return -ENOMEM; + + SET_NETDEV_DEV(ndev, &pdev->dev); + priv = netdev_priv(ndev); + platform_set_drvdata(pdev, ndev); + + priv->variant = of_device_get_match_data(&pdev->dev); + if (!priv->variant) { + dev_err(&pdev->dev, "Missing sun8i-emac variant\n"); + return -EINVAL; + } + + priv->phy_node = of_parse_phandle(node, "phy", 0); + if (!priv->phy_node) { + netdev_err(ndev, "No associated PHY\n"); + return -ENODEV; + } + + priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, + "syscon"); + if (IS_ERR(priv->regmap)) { + ret = PTR_ERR(priv->regmap); + dev_err(&pdev->dev, "unable to map SYSCON:%d\n", ret); + return ret; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) { + ret = PTR_ERR(priv->base); + dev_err(&pdev->dev, "Cannot request MMIO: %d\n", ret); + return ret; + } + + priv->ahb_clk = devm_clk_get(&pdev->dev, "ahb"); + if (IS_ERR(priv->ahb_clk)) { + ret = PTR_ERR(priv->ahb_clk); + dev_err(&pdev->dev, "Cannot get AHB clock err=%d\n", ret); + goto probe_err; + } + + priv->rst_mac = devm_reset_control_get_optional(&pdev->dev, "ahb"); + if (IS_ERR(priv->rst_mac)) { + ret = PTR_ERR(priv->rst_mac); + if (ret == -EPROBE_DEFER) + return -EPROBE_DEFER; + dev_info(&pdev->dev, "No MAC reset control found %d\n", ret); + priv->rst_mac = NULL; + } + + priv->phy_interface = of_get_phy_mode(node); + if (priv->phy_interface < 0) { + netdev_err(ndev, "PHY interface mode node unspecified\n"); + return priv->phy_interface; + } + + switch (priv->phy_interface) { + case PHY_INTERFACE_MODE_MII: + if (!priv->variant->support_mii) + return -EINVAL; + break; + case PHY_INTERFACE_MODE_RMII: + if (!priv->variant->support_rmii) + return -EINVAL; + break; + case PHY_INTERFACE_MODE_RGMII: + if (!priv->variant->support_rgmii) + return -EINVAL; + break; + default: + netdev_err(ndev, "Unsupported interface mode: %s", + phy_modes(priv->phy_interface)); + return -EINVAL; + } + + if (priv->phy_interface == priv->variant->internal_phy) + priv->use_internal_phy = true; + + if (priv->use_internal_phy) { + priv->ephy_clk = devm_clk_get(&pdev->dev, "ephy"); + if (IS_ERR(priv->ephy_clk)) { + ret = PTR_ERR(priv->ephy_clk); + dev_err(&pdev->dev, "Cannot get EPHY clock err=%d\n", + ret); + goto probe_err; + } + + priv->rst_ephy = devm_reset_control_get_optional(&pdev->dev, + "ephy"); + if (IS_ERR(priv->rst_ephy)) { + ret = PTR_ERR(priv->rst_ephy); + if (ret == -EPROBE_DEFER) + goto probe_err; + dev_info(&pdev->dev, + "No EPHY reset control found %d\n", ret); + priv->rst_ephy = NULL; + } + } + + priv->irq = platform_get_irq(pdev, 0); + if (priv->irq < 0) { + ret = priv->irq; + dev_err(&pdev->dev, "Cannot claim IRQ: %d\n", ret); + goto probe_err; + } + + spin_lock_init(&priv->tx_lock); + + ndev->netdev_ops = &sun8i_emac_netdev_ops; + ndev->ethtool_ops = &sun8i_emac_ethtool_ops; + + priv->ndev = ndev; + priv->dev = &pdev->dev; + + ndev->hw_features = NETIF_F_SG | NETIF_F_HIGHDMA; + ndev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM | + NETIF_F_RXCSUM; + ndev->features |= ndev->hw_features; + ndev->hw_features |= NETIF_F_RXFCS; + ndev->hw_features |= NETIF_F_RXALL; + ndev->hw_features |= NETIF_F_LOOPBACK; + ndev->priv_flags |= IFF_UNICAST_FLT; + + ndev->watchdog_timeo = msecs_to_jiffies(5000); + netif_carrier_off(ndev); + + /* Benched on OPIPC with 100M, setting more than 256 does not give any + * perf boost + */ + priv->nbdesc_rx = 128; + priv->nbdesc_tx = 256; + + ret = register_netdev(ndev); + if (ret) { + dev_err(&pdev->dev, "ERROR: Register %s failed\n", ndev->name); + goto probe_err; + } + + return 0; + +probe_err: + free_netdev(ndev); + return ret; +} + +static int sun8i_emac_remove(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + + unregister_netdev(ndev); + platform_set_drvdata(pdev, NULL); + free_netdev(ndev); + + return 0; +} + +static const struct of_device_id sun8i_emac_of_match_table[] = { + { .compatible = "allwinner,sun8i-a83t-emac", + .data = &emac_variant_a83t }, + { .compatible = "allwinner,sun8i-h3-emac", + .data = &emac_variant_h3 }, + { .compatible = "allwinner,sun50i-a64-emac", + .data = &emac_variant_a64 }, + {} +}; +MODULE_DEVICE_TABLE(of, sun8i_emac_of_match_table); + +static struct platform_driver sun8i_emac_driver = { + .probe = sun8i_emac_probe, + .remove = sun8i_emac_remove, + .driver = { + .name = "sun8i-emac", + .of_match_table = sun8i_emac_of_match_table, + }, +}; + +module_platform_driver(sun8i_emac_driver); + +MODULE_DESCRIPTION("sun8i Ethernet driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com"); -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel This patch add support for sun8i-emac ethernet MAC hardware. It could be found in Allwinner H3/A83T/A64 SoCs. It supports 10/100/1000 Mbit/s speed with half/full duplex. It can use an internal PHY (MII 10/100) or an external PHY via RGMII/RMII. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- drivers/net/ethernet/allwinner/Kconfig | 13 + drivers/net/ethernet/allwinner/Makefile | 1 + drivers/net/ethernet/allwinner/sun8i-emac.c | 2255 +++++++++++++++++++++++++++ 3 files changed, 2269 insertions(+) create mode 100644 drivers/net/ethernet/allwinner/sun8i-emac.c diff --git a/drivers/net/ethernet/allwinner/Kconfig b/drivers/net/ethernet/allwinner/Kconfig index 47da7e7..060569c 100644 --- a/drivers/net/ethernet/allwinner/Kconfig +++ b/drivers/net/ethernet/allwinner/Kconfig @@ -33,4 +33,17 @@ config SUN4I_EMAC To compile this driver as a module, choose M here. The module will be called sun4i-emac. +config SUN8I_EMAC + tristate "Allwinner sun8i EMAC support" + depends on ARCH_SUNXI || COMPILE_TEST + depends on OF + select MII + select PHYLIB + ---help--- + This driver support the sun8i EMAC ethernet driver present on + H3/A83T/A64 Allwinner SoCs. + + To compile this driver as a module, choose M here. The module + will be called sun8i-emac. + endif # NET_VENDOR_ALLWINNER diff --git a/drivers/net/ethernet/allwinner/Makefile b/drivers/net/ethernet/allwinner/Makefile index 03129f7..8bd1693c 100644 --- a/drivers/net/ethernet/allwinner/Makefile +++ b/drivers/net/ethernet/allwinner/Makefile @@ -3,3 +3,4 @@ # obj-$(CONFIG_SUN4I_EMAC) += sun4i-emac.o +obj-$(CONFIG_SUN8I_EMAC) += sun8i-emac.o diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c new file mode 100644 index 0000000..1c4bc80 --- /dev/null +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c @@ -0,0 +1,2255 @@ +/* + * sun8i-emac driver + * + * Copyright (C) 2015-2016 Corentin LABBE <clabbe.montjoie@gmail.com> + * + * This is the driver for Allwinner Ethernet MAC found in H3/A83T/A64 SoC + * + * TODO: + * - MAC filtering + * - Jumbo frame + * - features rx-all (NETIF_F_RXALL_BIT) + * - PM runtime + */ +#include <linux/bitops.h> +#include <linux/clk.h> +#include <linux/dma-mapping.h> +#include <linux/etherdevice.h> +#include <linux/interrupt.h> +#include <linux/iopoll.h> +#include <linux/mii.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/of_device.h> +#include <linux/of_mdio.h> +#include <linux/of_net.h> +#include <linux/phy.h> +#include <linux/pinctrl/consumer.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/scatterlist.h> +#include <linux/skbuff.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> + +#define EMAC_BASIC_CTL0 0x00 +#define EMAC_BASIC_CTL1 0x04 +#define EMAC_INT_STA 0x08 +#define EMAC_INT_EN 0x0C +#define EMAC_TX_CTL0 0x10 +#define EMAC_TX_CTL1 0x14 +#define EMAC_TX_FLOW_CTL 0x1C +#define EMAC_RX_CTL0 0x24 +#define EMAC_RX_CTL1 0x28 +#define EMAC_RX_FRM_FLT 0x38 +#define EMAC_MDIO_CMD 0x48 +#define EMAC_MDIO_DATA 0x4C +#define EMAC_TX_DMA_STA 0xB0 +#define EMAC_TX_CUR_DESC 0xB4 +#define EMAC_TX_CUR_BUF 0xB8 +#define EMAC_RX_DMA_STA 0xC0 + +#define MDIO_CMD_MII_BUSY BIT(0) +#define MDIO_CMD_MII_WRITE BIT(1) +#define MDIO_CMD_MII_PHY_REG_ADDR_MASK GENMASK(8, 4) +#define MDIO_CMD_MII_PHY_REG_ADDR_SHIFT 4 +#define MDIO_CMD_MII_PHY_ADDR_MASK GENMASK(16, 12) +#define MDIO_CMD_MII_PHY_ADDR_SHIFT 12 + +#define EMAC_MACADDR_HI 0x50 +#define EMAC_MACADDR_LO 0x54 + +#define EMAC_RX_DESC_LIST 0x34 +#define EMAC_TX_DESC_LIST 0x20 + +#define EMAC_RX_DO_CRC BIT(27) +#define EMAC_RX_STRIP_FCS BIT(28) + +#define LE32_BIT(x) (cpu_to_le32(BIT(x))) + +#define EMAC_COULD_BE_USED_BY_DMA LE32_BIT(31) + +/* Used in RX_CTL1*/ +#define EMAC_RX_DMA_EN BIT(30) +#define EMAC_RX_DMA_START BIT(31) +/* Used in TX_CTL1*/ +#define EMAC_TX_DMA_EN BIT(30) +#define EMAC_TX_DMA_START BIT(31) + +/* Used in RX_CTL0 */ +#define EMAC_RX_RECEIVER_EN BIT(31) +/* Used in TX_CTL0 */ +#define EMAC_TX_TRANSMITTER_EN BIT(31) + +/* Basic CTL0 */ +#define EMAC_BCTL0_FD BIT(0) +#define EMAC_BCTL0_SPEED_10 2 +#define EMAC_BCTL0_SPEED_100 3 +#define EMAC_BCTL0_SPEED_MASK GENMASK(3, 2) +#define EMAC_BCTL0_SPEED_SHIFT 2 + +#define EMAC_FLOW_RX 1 +#define EMAC_FLOW_TX 2 + +#define EMAC_TX_INT BIT(0) +#define EMAC_TX_DMA_STOP_INT BIT(1) +#define EMAC_TX_BUF_UA_INT BIT(2) +#define EMAC_TX_TIMEOUT_INT BIT(3) +#define EMAC_TX_UNDERFLOW_INT BIT(4) +#define EMAC_TX_EARLY_INT BIT(5) +#define EMAC_RX_INT BIT(8) +#define EMAC_RX_BUF_UA_INT BIT(9) +#define EMAC_RX_DMA_STOP_INT BIT(10) +#define EMAC_RX_TIMEOUT_INT BIT(11) +#define EMAC_RX_OVERFLOW_INT BIT(12) +#define EMAC_RX_EARLY_INT BIT(13) +#define EMAC_RGMII_STA_INT BIT(16) + +/* Bits used in frame RX status */ +#define EMAC_DSC_RX_FIRST BIT(9) +#define EMAC_DSC_RX_LAST BIT(8) + +/* Bits used in frame TX ctl */ +#define EMAC_MAGIC_TX_BIT LE32_BIT(24) +#define EMAC_TX_DO_CRC (LE32_BIT(27) | LE32_BIT(28)) +#define EMAC_DSC_TX_FIRST LE32_BIT(29) +#define EMAC_DSC_TX_LAST LE32_BIT(30) +#define EMAC_WANT_INT LE32_BIT(31) + +/* struct emac_variant - Describe an emac variant of sun8i-emac + * @default_syscon_value: Default value of the syscon EMAC register + * The default_syscon_value is also used for powering down the PHY + * @internal_phy: which PHY type is internal + * @support_mii: Does the SoC support MII + * @support_rmii: Does the SoC support RMII + * @support_rgmii: Does the SoC support RGMII + */ +struct emac_variant { + u32 default_syscon_value; + int internal_phy; + bool support_mii; + bool support_rmii; + bool support_rgmii; +}; + +static const struct emac_variant emac_variant_h3 = { + .default_syscon_value = 0x58000, + .internal_phy = PHY_INTERFACE_MODE_MII, + .support_mii = true, + .support_rmii = true, + .support_rgmii = true +}; + +static const struct emac_variant emac_variant_a83t = { + .default_syscon_value = 0, + .internal_phy = 0, + .support_mii = true, + .support_rgmii = true +}; + +static const struct emac_variant emac_variant_a64 = { + .default_syscon_value = 0, + .internal_phy = 0, + .support_mii = true, + .support_rmii = true, + .support_rgmii = true +}; + +static const char const estats_str[][ETH_GSTRING_LEN] = { + /* errors */ + "rx_payload_error", + "rx_CRC_error", + "rx_phy_error", + "rx_length_error", + "rx_col_error", + "rx_header_error", + "rx_overflow_error", + "rx_saf_error", + "rx_daf_error", + "rx_buf_error", + "rx_invalid_error", + "tx_timeout", + /* misc infos */ + "tx_stop_queue", + "rx_dma_ua", + "rx_dma_stop", + "tx_dma_ua", + "tx_dma_stop", + "rx_hw_csum", + "tx_hw_csum", + /* interrupts */ + "rx_int", + "tx_int", + "tx_early_int", + "tx_underflow_int", + "tx_timeout_int", + "rx_early_int", + "rx_overflow_int", + "rx_timeout_int", + "rgmii_state_int", + /* debug */ + "tx_used_desc", + "napi_schedule", + "napi_underflow", +}; + +struct sun8i_emac_stats { + u64 rx_payload_error; + u64 rx_crc_error; + u64 rx_phy_error; + u64 rx_length_error; + u64 rx_col_error; + u64 rx_header_error; + u64 rx_overflow_error; + u64 rx_saf_fail; + u64 rx_daf_fail; + u64 rx_buf_error; + u64 rx_invalid_error; + u64 tx_timeout; + + u64 tx_stop_queue; + u64 rx_dma_ua; + u64 rx_dma_stop; + u64 tx_dma_ua; + u64 tx_dma_stop; + u64 rx_hw_csum; + u64 tx_hw_csum; + + u64 rx_int; + u64 tx_int; + u64 tx_early_int; + u64 tx_underflow_int; + u64 tx_timeout_int; + u64 rx_early_int; + u64 rx_overflow_int; + u64 rx_timeout_int; + u64 rgmii_state_int; + + u64 tx_used_desc; + u64 napi_schedule; + u64 napi_underflow; +}; + +/* The datasheet said that each descriptor can transfers up to 4096bytes + * But latter, a register documentation reduce that value to 2048 + * Anyway using 2048 cause strange behaviours and even BSP driver use 2047 + */ +#define DESC_BUF_MAX 2044 + +/* MAGIC value for knowing if a descriptor is available or not */ +#define DCLEAN cpu_to_le32(BIT(16) | BIT(14) | BIT(12) | BIT(10) | BIT(9)) + +/* struct dma_desc - Structure of DMA descriptor used by the hardware + * @status: Status of the frame written by HW, so RO for the + * driver (except for BIT(31) which is R/W) + * @ctl: Information on the frame written by the driver (INT, len,...) + * @buf_addr: physical address of the frame data + * @next: physical address of next dma_desc + */ +struct dma_desc { + __le32 status; + __le32 ctl; + __le32 buf_addr; + __le32 next; +}; + +/* Describe how data from skb are DMA mapped (used in txinfo map member) */ +#define MAP_SINGLE 1 +#define MAP_PAGE 2 + +/* Structure for storing information about data in TX ring buffer */ +struct txinfo { + struct sk_buff *skb; + int map; +}; + +struct sun8i_emac_priv { + void __iomem *base; + struct regmap *regmap; + int irq; + struct device *dev; + struct net_device *ndev; + struct mii_bus *mdio; + struct napi_struct napi; + spinlock_t tx_lock;/* control the access of transmit descriptors */ + int duplex; + int speed; + int link; + int phy_interface; + const struct emac_variant *variant; + struct device_node *phy_node; + struct clk *ahb_clk; + struct clk *ephy_clk; + bool use_internal_phy; + + struct reset_control *rst_mac; + struct reset_control *rst_ephy; + + struct dma_desc *dd_rx; + dma_addr_t dd_rx_phy; + struct dma_desc *dd_tx; + dma_addr_t dd_tx_phy; + struct sk_buff **rx_skb; + struct txinfo *txl; + + int nbdesc_tx; + int nbdesc_rx; + int tx_slot; + int tx_dirty; + int rx_dirty; + struct sun8i_emac_stats estats; + u32 msg_enable; + int flow_ctrl; + int pause; +}; + +static irqreturn_t sun8i_emac_dma_interrupt(int irq, void *dev_id); + +static void rb_inc(int *p, const int max) +{ + (*p)++; + (*p) %= max; +} + +/* Locking strategy: + * RX queue does not need any lock since only sun8i_emac_poll() access it. + * (All other RX modifiers (ringparam/ndo_stop) disable NAPI and so + * sun8i_emac_poll()) + * TX queue is handled by sun8i_emac_xmit(), sun8i_emac_complete_xmit() and + * sun8i_emac_tx_timeout() + * (All other RX modifiers (ringparam/ndo_stop) disable NAPI and stop queue) + * + * sun8i_emac_xmit() could fire only once (netif_tx_lock) + * sun8i_emac_complete_xmit() could fire only once (called from NAPI) + * sun8i_emac_tx_timeout() could fire only once (netif_tx_lock) and could not + * race with sun8i_emac_xmit (due to netif_tx_lock) and with + * sun8i_emac_complete_xmit which disable NAPI. + * + * So only sun8i_emac_xmit and sun8i_emac_complete_xmit could fire at the same + * time. + * But they never could modify the same descriptors: + * - sun8i_emac_complete_xmit() will modify only descriptors with empty status + * - sun8i_emac_xmit() will modify only descriptors set to DCLEAN + * Proper memory barriers ensure that descriptor set to DCLEAN could not be + * modified latter by sun8i_emac_complete_xmit(). + */ + +/* Return the number of contiguous free descriptors + * starting from tx_slot + */ +static int rb_tx_numfreedesc(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + if (priv->tx_slot < priv->tx_dirty) + return priv->tx_dirty - priv->tx_slot; + + return (priv->nbdesc_tx - priv->tx_slot) + priv->tx_dirty; +} + +/* sun8i_emac_rx_skb - Allocate a skb in a DMA descriptor + * + * @ndev: The net_device for this interface + * @i: index of slot to fill + * + * Refill a DMA descriptor with a fresh skb and map it for DMA. +*/ +static int sun8i_emac_rx_skb(struct net_device *ndev, int i) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + struct sk_buff *skb; + + ddesc = priv->dd_rx + i; + + ddesc->ctl = 0; + + skb = netdev_alloc_skb_ip_align(ndev, DESC_BUF_MAX); + if (!skb) + return -ENOMEM; + + /* should not happen */ + if (unlikely(priv->rx_skb[i])) + dev_warn(priv->dev, "BUG: Leaking a skbuff\n"); + + priv->rx_skb[i] = skb; + + ddesc->buf_addr = dma_map_single(priv->dev, skb->data, + DESC_BUF_MAX, DMA_FROM_DEVICE); + if (dma_mapping_error(priv->dev, ddesc->buf_addr)) { + dev_err(priv->dev, "ERROR: Cannot map RX buffer for DMA\n"); + dev_kfree_skb(skb); + return -EFAULT; + } + /* We cannot direcly use cpu_to_le32() after dma_map_single + * since dma_mapping_error use it + */ + ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr); + ddesc->ctl |= cpu_to_le32(DESC_BUF_MAX); + /* EMAC_COULD_BE_USED_BY_DMA must be the last value written */ + wmb(); + ddesc->status = EMAC_COULD_BE_USED_BY_DMA; + + return 0; +} + +static void sun8i_emac_stop_tx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + netif_stop_queue(ndev); + + v = readl(priv->base + EMAC_TX_CTL0); + /* Disable transmitter after current reception */ + v &= ~EMAC_TX_TRANSMITTER_EN; + writel(v, priv->base + EMAC_TX_CTL0); + + v = readl(priv->base + EMAC_TX_CTL1); + /* Stop TX DMA */ + v &= ~EMAC_TX_DMA_EN; + writel(v, priv->base + EMAC_TX_CTL1); + + /* We must be sure that all is stopped before leaving this function */ + wmb(); +} + +static void sun8i_emac_stop_rx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_RX_CTL0); + /* Disable receiver after current reception */ + v &= ~EMAC_RX_RECEIVER_EN; + writel(v, priv->base + EMAC_RX_CTL0); + + v = readl(priv->base + EMAC_RX_CTL1); + /* Stop RX DMA */ + v &= ~EMAC_RX_DMA_EN; + writel(v, priv->base + EMAC_RX_CTL1); + + /* We must be sure that all is stopped before leaving this function */ + wmb(); +} + +static void sun8i_emac_start_rx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_RX_CTL0); + /* Enable receiver */ + v |= EMAC_RX_RECEIVER_EN; + writel(v, priv->base + EMAC_RX_CTL0); + + v = readl(priv->base + EMAC_RX_CTL1); + v |= EMAC_RX_DMA_START; + v |= EMAC_RX_DMA_EN; + writel(v, priv->base + EMAC_RX_CTL1); +} + +static void sun8i_emac_start_tx(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_TX_CTL0); + v |= EMAC_TX_TRANSMITTER_EN; + writel(v, priv->base + EMAC_TX_CTL0); + + v = readl(priv->base + EMAC_TX_CTL1); + v |= EMAC_TX_DMA_START; + v |= EMAC_TX_DMA_EN; + writel(v, priv->base + EMAC_TX_CTL1); +} + +/* sun8i_emac_set_macaddr - Set MAC address for slot index + * + * @addr: the MAC address to set + * @index: The index of slot where to set address. + * + * The slot 0 is the main MAC address + */ +static void sun8i_emac_set_macaddr(struct sun8i_emac_priv *priv, + const u8 *addr, int index) +{ + u32 v; + + dev_info(priv->dev, "device MAC address slot %d %pM", index, addr); + + v = (addr[5] << 8) | addr[4]; + writel(v, priv->base + EMAC_MACADDR_HI + index * 8); + + v = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0]; + writel(v, priv->base + EMAC_MACADDR_LO + index * 8); +} + +static void sun8i_emac_set_link_mode(struct sun8i_emac_priv *priv) +{ + u32 v; + + v = readl(priv->base + EMAC_BASIC_CTL0); + + if (priv->duplex) + v |= EMAC_BCTL0_FD; + else + v &= ~EMAC_BCTL0_FD; + + v &= ~EMAC_BCTL0_SPEED_MASK; + + switch (priv->speed) { + case 1000: + break; + case 100: + v |= EMAC_BCTL0_SPEED_100 << EMAC_BCTL0_SPEED_SHIFT; + break; + case 10: + v |= EMAC_BCTL0_SPEED_10 << EMAC_BCTL0_SPEED_SHIFT; + break; + default: + dev_err(priv->dev, "Unsupported speed %d\n", priv->speed); + return; + } + + writel(v, priv->base + EMAC_BASIC_CTL0); +} + +static void sun8i_emac_flow_ctrl(struct sun8i_emac_priv *priv, int duplex, + int fc) +{ + u32 flow = 0; + + flow = readl(priv->base + EMAC_RX_CTL0); + if (fc & EMAC_FLOW_RX) + flow |= BIT(16); + else + flow &= ~BIT(16); + writel(flow, priv->base + EMAC_RX_CTL0); + + flow = readl(priv->base + EMAC_TX_FLOW_CTL); + if (fc & EMAC_FLOW_TX) + flow |= BIT(0); + else + flow &= ~BIT(0); + writel(flow, priv->base + EMAC_TX_FLOW_CTL); +} + +/* Grab a frame into a skb from descriptor number i */ +static int sun8i_emac_rx_from_ddesc(struct net_device *ndev, int i) +{ + struct sk_buff *skb; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc = priv->dd_rx + i; + int frame_len; + int rxcsum_done = 0; + u32 dstatus = le32_to_cpu(ddesc->status); + + if (ndev->features & NETIF_F_RXCSUM) + rxcsum_done = 1; + + /* bit0/bit7 work only on IPv4/IPv6 TCP traffic, + * (not on ARP for example) so we do not raise rx_errors/discard frame + */ + /* the checksum or length of received frame's payload is wrong*/ + if (dstatus & BIT(0)) { + priv->estats.rx_payload_error++; + rxcsum_done = 0; + } + + /* RX_CRC_ERR */ + if (dstatus & BIT(1)) { + priv->ndev->stats.rx_errors++; + priv->ndev->stats.rx_crc_errors++; + priv->estats.rx_crc_error++; + goto discard_frame; + } + + /* RX_PHY_ERR */ + if ((dstatus & BIT(3))) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_phy_error++; + goto discard_frame; + } + + /* RX_LENGTH_ERR */ + if ((dstatus & BIT(4))) { + priv->ndev->stats.rx_errors++; + priv->ndev->stats.rx_length_errors++; + priv->estats.rx_length_error++; + goto discard_frame; + } + + /* RX_COL_ERR */ + if ((dstatus & BIT(6))) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_col_error++; + goto discard_frame; + } + + /* RX_HEADER_ERR */ + if ((dstatus & BIT(7))) { + priv->estats.rx_header_error++; + rxcsum_done = 0; + } + + /* RX_OVERFLOW_ERR */ + if ((dstatus & BIT(11))) { + priv->ndev->stats.rx_over_errors++; + priv->estats.rx_overflow_error++; + goto discard_frame; + } + + /* RX_NO_ENOUGTH_BUF_ERR */ + if ((dstatus & BIT(14))) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_buf_error++; + goto discard_frame; + } + + /* BIT(9) is for the first frame, not having it is bad since we do not + * handle Jumbo frame + */ + if ((dstatus & EMAC_DSC_RX_FIRST) == 0) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_invalid_error++; + goto discard_frame; + } + + /* this frame is not the last */ + if ((dstatus & EMAC_DSC_RX_LAST) == 0) { + priv->ndev->stats.rx_errors++; + priv->estats.rx_invalid_error++; + goto discard_frame; + } + + frame_len = (dstatus >> 16) & 0x3FFF; + if (!(ndev->features & NETIF_F_RXFCS)) + frame_len -= ETH_FCS_LEN; + + skb = priv->rx_skb[i]; + + netif_dbg(priv, rx_status, priv->ndev, + "%s from %02d %pad len=%d status=%x st=%x\n", + __func__, i, &ddesc, frame_len, dstatus, + cpu_to_le32(ddesc->ctl)); + + skb_put(skb, frame_len); + + dma_unmap_single(priv->dev, le32_to_cpu(ddesc->buf_addr), DESC_BUF_MAX, + DMA_FROM_DEVICE); + skb->protocol = eth_type_trans(skb, priv->ndev); + if (rxcsum_done) { + skb->ip_summed = CHECKSUM_UNNECESSARY; + priv->estats.rx_hw_csum++; + } else { + skb->ip_summed = CHECKSUM_PARTIAL; + } + + priv->ndev->stats.rx_packets++; + priv->ndev->stats.rx_bytes += frame_len; + priv->rx_skb[i] = NULL; + + sun8i_emac_rx_skb(ndev, i); + napi_gro_receive(&priv->napi, skb); + + return 0; + /* If the frame need to be dropped, we simply reuse the buffer */ +discard_frame: + ddesc->ctl = cpu_to_le32(DESC_BUF_MAX); + /* EMAC_COULD_BE_USED_BY_DMA must be the last value written */ + wmb(); + ddesc->status = EMAC_COULD_BE_USED_BY_DMA; + return 0; +} + +/* Iterate over dma_desc for finding completed xmit. + * + * The problem is: how to know that a descriptor is sent and not just in + * preparation. + * Need to have status=0 and st set but this is the state of first frame just + * before setting the own-by-DMA bit. + * The solution is to used the artificial value DCLEAN. + */ +static int sun8i_emac_complete_xmit(struct net_device *ndev, int budget) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + int frame_len; + int work = 0; + unsigned int bytes_compl = 0, pkts_compl = 0; + u32 dstatus; + + do { + ddesc = priv->dd_tx + priv->tx_dirty; + + if (ddesc->status & EMAC_COULD_BE_USED_BY_DMA) + goto xmit_end; + + if (ddesc->status == DCLEAN) + goto xmit_end; + + dstatus = cpu_to_le32(ddesc->status); + + if (ddesc->status == 0 && !ddesc->ctl) { + dev_err(priv->dev, "BUG: reached the void %d %d\n", + priv->tx_dirty, priv->tx_slot); + goto xmit_end; + } + + /* TX_UNDERFLOW_ERR */ + if (dstatus & BIT(1)) + priv->ndev->stats.tx_errors++; + /* TX_DEFER_ERR */ + if (dstatus & BIT(2)) + priv->ndev->stats.tx_errors++; + /* BIT 6:3 numbers of collisions */ + if (dstatus & 0x78) + priv->ndev->stats.collisions += + (dstatus & 0x78) >> 3; + /* TX_COL_ERR_1 */ + if (dstatus & BIT(8)) + priv->ndev->stats.tx_errors++; + /* TX_COL_ERR_0 */ + if (dstatus & BIT(9)) + priv->ndev->stats.tx_errors++; + /* TX_CRS_ERR */ + if (dstatus & BIT(10)) + priv->ndev->stats.tx_carrier_errors++; + /* TX_PAYLOAD_ERR */ + if (dstatus & BIT(12)) + priv->ndev->stats.tx_errors++; + /* TX_LENGTH_ERR */ + if (dstatus & BIT(14)) + priv->ndev->stats.tx_errors++; + /* TX_HEADER_ERR */ + if (dstatus & BIT(16)) + priv->ndev->stats.tx_errors++; + + frame_len = le32_to_cpu(ddesc->ctl) & 0x3FFF; + bytes_compl += frame_len; + + if (priv->txl[priv->tx_dirty].map == MAP_SINGLE) + dma_unmap_single(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + else + dma_unmap_page(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + /* we can free skb only on last frame */ + if (priv->txl[priv->tx_dirty].skb && + (ddesc->ctl & EMAC_DSC_TX_LAST)) { + dev_kfree_skb_irq(priv->txl[priv->tx_dirty].skb); + pkts_compl++; + } + + priv->txl[priv->tx_dirty].skb = NULL; + priv->txl[priv->tx_dirty].map = 0; + ddesc->ctl = 0; + /* setting status to DCLEAN is the last value to be set */ + wmb(); + ddesc->status = DCLEAN; + work++; + + rb_inc(&priv->tx_dirty, priv->nbdesc_tx); + ddesc = priv->dd_tx + priv->tx_dirty; + } while (ddesc->ctl && + !(ddesc->status & EMAC_COULD_BE_USED_BY_DMA) && + work < budget); + +xmit_end: + netdev_completed_queue(ndev, pkts_compl, bytes_compl); + + /* if we don't have handled all packets */ + if (work < budget) + work = 0; + + if (netif_queue_stopped(ndev) && + rb_tx_numfreedesc(ndev) > MAX_SKB_FRAGS + 1) + netif_wake_queue(ndev); + return work; +} + +static int sun8i_emac_poll(struct napi_struct *napi, int budget) +{ + struct sun8i_emac_priv *priv = + container_of(napi, struct sun8i_emac_priv, napi); + struct net_device *ndev = priv->ndev; + int worked; + struct dma_desc *ddesc; + + priv->estats.napi_schedule++; + worked = sun8i_emac_complete_xmit(ndev, budget); + + ddesc = priv->dd_rx + priv->rx_dirty; + while (!(ddesc->status & EMAC_COULD_BE_USED_BY_DMA) && + worked < budget) { + sun8i_emac_rx_from_ddesc(ndev, priv->rx_dirty); + worked++; + rb_inc(&priv->rx_dirty, priv->nbdesc_rx); + ddesc = priv->dd_rx + priv->rx_dirty; + }; + if (worked < budget) { + priv->estats.napi_underflow++; + napi_complete(&priv->napi); + writel(EMAC_RX_INT | EMAC_TX_INT, priv->base + EMAC_INT_EN); + } + return worked; +} + +static int sun8i_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg) +{ + struct net_device *ndev = bus->priv; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int err; + u32 reg; + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + reg &= ~MDIO_CMD_MII_WRITE; + reg &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; + reg |= (phy_reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_REG_ADDR_MASK; + + reg &= ~MDIO_CMD_MII_PHY_ADDR_MASK; + + reg |= (phy_addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_ADDR_MASK; + + reg |= MDIO_CMD_MII_BUSY; + + writel(reg, priv->base + EMAC_MDIO_CMD); + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + return readl(priv->base + EMAC_MDIO_DATA); +} + +static int sun8i_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, + u16 data) +{ + struct net_device *ndev = bus->priv; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 reg; + int err; + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + reg &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; + reg |= (phy_reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_REG_ADDR_MASK; + + reg &= ~MDIO_CMD_MII_PHY_ADDR_MASK; + reg |= (phy_addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_ADDR_MASK; + + reg |= MDIO_CMD_MII_WRITE; + reg |= MDIO_CMD_MII_BUSY; + + writel(reg, priv->base + EMAC_MDIO_CMD); + writel(data, priv->base + EMAC_MDIO_DATA); + + err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg, + !(reg & MDIO_CMD_MII_BUSY), 100, 10000); + if (err) { + dev_err(priv->dev, "%s timeout %x\n", __func__, reg); + return err; + } + + return 0; +} + +static int sun8i_emac_mdio_register(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct mii_bus *bus; + int ret; + + bus = mdiobus_alloc(); + if (!bus) { + netdev_err(ndev, "Failed to allocate a new mdio bus\n"); + return -ENOMEM; + } + + bus->name = dev_name(priv->dev); + bus->read = &sun8i_mdio_read; + bus->write = &sun8i_mdio_write; + snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%x", bus->name, priv->dev->id); + + bus->parent = priv->dev; + bus->priv = ndev; + + ret = of_mdiobus_register(bus, priv->dev->of_node); + if (ret) { + netdev_err(ndev, "Could not register a MDIO bus: %d\n", ret); + mdiobus_free(bus); + return ret; + } + + priv->mdio = bus; + + return 0; +} + +static void sun8i_emac_mdio_unregister(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + mdiobus_unregister(priv->mdio); + mdiobus_free(priv->mdio); +} + +/* Run within phydev->lock */ +static void sun8i_emac_adjust_link(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct phy_device *phydev = ndev->phydev; + int new_state = 0; + + netif_dbg(priv, link, priv->ndev, + "%s link=%x duplex=%x speed=%x\n", __func__, + phydev->link, phydev->duplex, phydev->speed); + if (!phydev) + return; + + if (phydev->link) { + if (phydev->duplex != priv->duplex) { + new_state = 1; + priv->duplex = phydev->duplex; + } + if (phydev->pause) + sun8i_emac_flow_ctrl(priv, phydev->duplex, + priv->flow_ctrl); + + if (phydev->speed != priv->speed) { + new_state = 1; + priv->speed = phydev->speed; + } + + if (priv->link == 0) { + new_state = 1; + priv->link = phydev->link; + } + + netif_dbg(priv, link, priv->ndev, + "%s new=%d link=%d pause=%d\n", + __func__, new_state, priv->link, phydev->pause); + if (new_state) + sun8i_emac_set_link_mode(priv); + } else if (priv->link != phydev->link) { + new_state = 1; + priv->link = 0; + priv->speed = 0; + priv->duplex = -1; + } + + if (new_state) + phy_print_status(phydev); +} + +/* H3 specific bits for EPHY */ +#define H3_EPHY_ADDR_SHIFT 20 +#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ +#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ +#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ + +/* H3/A64 specific bits */ +#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */ + +/* Generic system control EMAC_CLK bits */ +#define SYSCON_ETXDC_MASK GENMASK(2, 0) +#define SYSCON_ETXDC_SHIFT 10 +#define SYSCON_ERXDC_MASK GENMASK(4, 0) +#define SYSCON_ERXDC_SHIFT 5 +/* EMAC PHY Interface Type */ +#define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */ +#define SYSCON_ETCS_MASK GENMASK(1, 0) +#define SYSCON_ETCS_MII 0x0 +#define SYSCON_ETCS_EXT_GMII 0x1 +#define SYSCON_ETCS_INT_GMII 0x2 +#define SYSCON_EMAC_REG 0x30 + +static int sun8i_emac_set_syscon(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct device_node *node = priv->dev->of_node; + int ret; + u32 reg, val; + + reg = priv->variant->default_syscon_value; + + if (priv->variant->internal_phy) { + if (!priv->use_internal_phy) { + /* switch to external PHY interface */ + reg &= ~H3_EPHY_SELECT; + } else { + reg |= H3_EPHY_SELECT; + reg &= ~H3_EPHY_SHUTDOWN; + + if (of_property_read_bool(priv->phy_node, + "allwinner,leds-active-low")) + reg |= H3_EPHY_LED_POL; + + ret = of_mdio_parse_addr(priv->dev, priv->phy_node); + if (ret < 0) { + netdev_err(ndev, "Could not parse MDIO addr\n"); + return ret; + } + /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY + * address. No need to mask it again. + */ + reg |= ret << H3_EPHY_ADDR_SHIFT; + } + } + + if (!of_property_read_u32(node, "allwinner,tx-delay", &val)) { + if (val <= SYSCON_ETXDC_MASK) { + reg &= ~(SYSCON_ETXDC_MASK << SYSCON_ETXDC_SHIFT); + reg |= (val << SYSCON_ETXDC_SHIFT); + } else { + netdev_warn(ndev, "Invalid TX clock delay: %d\n", val); + } + } + + if (!of_property_read_u32(node, "allwinner,rx-delay", &val)) { + if (val <= SYSCON_ERXDC_MASK) { + reg &= ~(SYSCON_ERXDC_MASK << SYSCON_ERXDC_SHIFT); + reg |= (val << SYSCON_ERXDC_SHIFT); + } else { + netdev_warn(ndev, "Invalid RX clock delay: %d\n", val); + } + } + + /* Clear interface mode bits */ + reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT); + if (priv->variant->support_rmii) + reg &= ~SYSCON_RMII_EN; + + switch (priv->phy_interface) { + case PHY_INTERFACE_MODE_MII: + /* default */ + break; + case PHY_INTERFACE_MODE_RGMII: + reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII; + break; + case PHY_INTERFACE_MODE_RMII: + reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII; + break; + default: + netdev_err(ndev, "Unsupported interface mode: %s", + phy_modes(priv->phy_interface)); + return -EINVAL; + } + + regmap_write(priv->regmap, SYSCON_EMAC_REG, reg); + + return 0; +} + +static void sun8i_emac_unset_syscon(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 reg = priv->variant->default_syscon_value; + + regmap_write(priv->regmap, SYSCON_EMAC_REG, reg); +} + +/* Set Management Data Clock, must be call after device reset */ +static void sun8i_emac_set_mdc(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + unsigned long rate; + u32 reg; + + rate = clk_get_rate(priv->ahb_clk); + if (rate > 160000000) + reg = 0x3 << 20; /* AHB / 128 */ + else if (rate > 80000000) + reg = 0x2 << 20; /* AHB / 64 */ + else if (rate > 40000000) + reg = 0x1 << 20; /* AHB / 32 */ + else + reg = 0x0 << 20; /* AHB / 16 */ + netif_dbg(priv, link, ndev, "MDC auto : %x\n", reg); + writel(reg, priv->base + EMAC_MDIO_CMD); +} + +/* "power" the device, by enabling clk/reset/regulators */ +static int sun8i_emac_power(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int ret; + + ret = clk_prepare_enable(priv->ahb_clk); + if (ret) { + netdev_err(ndev, "Could not enable AHB clock\n"); + return ret; + } + + if (priv->rst_mac) { + ret = reset_control_deassert(priv->rst_mac); + if (ret) { + netdev_err(ndev, "Could not deassert reset\n"); + goto err_reset; + } + } + + if (priv->ephy_clk) { + ret = clk_prepare_enable(priv->ephy_clk); + if (ret) { + netdev_err(ndev, "Could not enable EPHY clock\n"); + goto err_ephy_clk; + } + } + + if (priv->rst_ephy) { + ret = reset_control_deassert(priv->rst_ephy); + if (ret) { + netdev_err(ndev, "Could not deassert EPHY reset\n"); + goto err_ephy_reset; + } + } + + return 0; + +err_ephy_reset: + if (priv->ephy_clk) + clk_disable_unprepare(priv->ephy_clk); +err_ephy_clk: + if (priv->rst_mac) + reset_control_assert(priv->rst_mac); +err_reset: + clk_disable_unprepare(priv->ahb_clk); + return ret; +} + +/* "Unpower" the device, disabling clocks and regulators, asserting reset */ +static void sun8i_emac_unpower(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + if (priv->rst_ephy) + reset_control_assert(priv->rst_ephy); + + if (priv->ephy_clk) + clk_disable_unprepare(priv->ephy_clk); + + if (priv->rst_mac) + reset_control_assert(priv->rst_mac); + + clk_disable_unprepare(priv->ahb_clk); +} + +static int sun8i_emac_init(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct device_node *node = priv->dev->of_node; + const u8 *addr; + + /* Try to get MAC address from DT, or assign a random one */ + addr = of_get_mac_address(node); + if (addr) + ether_addr_copy(ndev->dev_addr, addr); + else + eth_hw_addr_random(ndev); + + return sun8i_emac_power(ndev); +} + +static void sun8i_emac_uninit(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + mdiobus_unregister(priv->mdio); + + sun8i_emac_unpower(ndev); +} + +static int sun8i_emac_mdio_probe(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct phy_device *phydev = NULL; + + phydev = of_phy_connect(ndev, priv->phy_node, &sun8i_emac_adjust_link, + 0, priv->phy_interface); + + if (!phydev) { + netdev_err(ndev, "Could not attach to PHY\n"); + return -ENODEV; + } + + phy_attached_info(phydev); + + /* mask with MAC supported features */ + phydev->supported &= PHY_GBIT_FEATURES; + phydev->advertising = phydev->supported; + + priv->link = 0; + priv->speed = 0; + priv->duplex = -1; + + return 0; +} + +/* Allocate both RX and TX ring buffer and init them + * This function also write the startbase of thoses ring in the device. + * All structures that help managing thoses rings are also handled + * by this functions (rx_skb/txl) + */ +static int sun8i_emac_alloc_rings(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + int err, i; + + priv->rx_skb = kcalloc(priv->nbdesc_rx, sizeof(struct sk_buff *), + GFP_KERNEL); + if (!priv->rx_skb) { + err = -ENOMEM; + goto rx_skb_error; + } + priv->txl = kcalloc(priv->nbdesc_tx, sizeof(struct txinfo), GFP_KERNEL); + if (!priv->txl) { + err = -ENOMEM; + goto tx_error; + } + + /* allocate/init RX ring */ + priv->dd_rx = dma_zalloc_coherent(priv->dev, + priv->nbdesc_rx * sizeof(struct dma_desc), + &priv->dd_rx_phy, GFP_KERNEL); + if (!priv->dd_rx) { + dev_err(priv->dev, "ERROR: cannot allocate DMA RX buffer"); + err = -ENOMEM; + goto dma_rx_error; + } + ddesc = priv->dd_rx; + for (i = 0; i < priv->nbdesc_rx; i++) { + sun8i_emac_rx_skb(ndev, i); + ddesc->next = cpu_to_le32(priv->dd_rx_phy + (i + 1) + * sizeof(struct dma_desc)); + ddesc++; + } + /* last descriptor point back to first one */ + ddesc--; + ddesc->next = cpu_to_le32(priv->dd_rx_phy); + + /* allocate/init TX ring */ + priv->dd_tx = dma_zalloc_coherent(priv->dev, + priv->nbdesc_tx * sizeof(struct dma_desc), + &priv->dd_tx_phy, GFP_KERNEL); + if (!priv->dd_tx) { + dev_err(priv->dev, "ERROR: cannot allocate DMA TX buffer"); + err = -ENOMEM; + goto dma_tx_error; + } + ddesc = priv->dd_tx; + for (i = 0; i < priv->nbdesc_tx; i++) { + ddesc->status = DCLEAN; + ddesc->ctl = 0; + ddesc->next = cpu_to_le32(priv->dd_tx_phy + (i + 1) + * sizeof(struct dma_desc)); + ddesc++; + } + /* last descriptor point back to first one */ + ddesc--; + ddesc->next = cpu_to_le32(priv->dd_tx_phy); + i--; + + priv->tx_slot = 0; + priv->tx_dirty = 0; + priv->rx_dirty = 0; + + /* write start of RX ring descriptor */ + writel(priv->dd_rx_phy, priv->base + EMAC_RX_DESC_LIST); + /* write start of TX ring descriptor */ + writel(priv->dd_tx_phy, priv->base + EMAC_TX_DESC_LIST); + + return 0; +dma_tx_error: + dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc), + priv->dd_rx, priv->dd_rx_phy); +dma_rx_error: + kfree(priv->txl); +tx_error: + kfree(priv->rx_skb); +rx_skb_error: + return err; +} + +static int sun8i_emac_open(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int err; + u32 v; + + err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, + dev_name(priv->dev), ndev); + if (err) { + dev_err(priv->dev, "Cannot request IRQ: %d\n", err); + return err; + } + + /* Set interface mode (and configure internal PHY on H3) */ + err = sun8i_emac_set_syscon(ndev); + if (err) + goto err_irq; + + /* Do SOFT RST */ + v = readl(priv->base + EMAC_BASIC_CTL1); + writel(v | 0x01, priv->base + EMAC_BASIC_CTL1); + + err = readl_poll_timeout(priv->base + EMAC_BASIC_CTL1, v, + !(v & 0x01), 100, 10000); + if (err) { + dev_err(priv->dev, "EMAC reset timeout\n"); + err = -EFAULT; + goto err_syscon; + } + + sun8i_emac_set_mdc(ndev); + + err = sun8i_emac_mdio_register(ndev); + if (err) + goto err_syscon; + + err = sun8i_emac_mdio_probe(ndev); + if (err) + goto err_syscon; + + /* DMA */ + v = (8 << 24);/* burst len */ + writel(v, priv->base + EMAC_BASIC_CTL1); + + writel(EMAC_RX_INT | EMAC_TX_INT, priv->base + EMAC_INT_EN); + + v = readl(priv->base + EMAC_RX_CTL0); + /* CHECK_CRC */ + if (ndev->features & NETIF_F_RXCSUM) + v |= EMAC_RX_DO_CRC; + else + v &= ~EMAC_RX_DO_CRC; + /* STRIP_FCS */ + if (ndev->features & NETIF_F_RXFCS) + v &= ~EMAC_RX_STRIP_FCS; + else + v |= EMAC_RX_STRIP_FCS; + writel(v, priv->base + EMAC_RX_CTL0); + + v = readl(priv->base + EMAC_TX_CTL1); + /* TX_MD Transmission starts after a full frame located in TX DMA FIFO*/ + v |= BIT(1); + /* Undocumented bit (called TX_NEXT_FRM in BSP), the original comment is + * "Operating on second frame increase the performance + * especially when transmit store-and-forward is used." + */ + v |= BIT(2); + writel(v, priv->base + EMAC_TX_CTL1); + + v = readl(priv->base + EMAC_RX_CTL1); + /* RX_MD RX DMA reads data from RX DMA FIFO to host memory after a + * complete frame has been written to RX DMA FIFO + */ + v |= BIT(1); + writel(v, priv->base + EMAC_RX_CTL1); + + sun8i_emac_set_macaddr(priv, ndev->dev_addr, 0); + + err = sun8i_emac_alloc_rings(ndev); + if (err) { + netdev_err(ndev, "Fail to allocate rings\n"); + goto err_mdio; + } + + phy_start(ndev->phydev); + + sun8i_emac_start_rx(ndev); + sun8i_emac_start_tx(ndev); + + netif_napi_add(ndev, &priv->napi, sun8i_emac_poll, 64); + napi_enable(&priv->napi); + netif_start_queue(ndev); + + return 0; +err_mdio: + phy_disconnect(ndev->phydev); +err_syscon: + sun8i_emac_unset_syscon(ndev); +err_irq: + free_irq(priv->irq, ndev); + return err; +} + +/* Clean the TX ring of any accepted skb for xmit */ +static void sun8i_emac_tx_clean(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int i; + struct dma_desc *ddesc; + int frame_len; + + for (i = 0; i < priv->nbdesc_tx; i++) { + if (priv->txl[i].skb) { + ddesc = priv->dd_tx + i; + frame_len = le32_to_cpu(ddesc->ctl) & 0x3FFF; + switch (priv->txl[i].map) { + case MAP_SINGLE: + dma_unmap_single(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + break; + case MAP_PAGE: + dma_unmap_page(priv->dev, + le32_to_cpu(ddesc->buf_addr), + frame_len, DMA_TO_DEVICE); + break; + default: + dev_err(priv->dev, "Trying to free an empty slot\n"); + continue; + } + dev_kfree_skb_any(priv->txl[i].skb); + priv->txl[i].skb = NULL; + ddesc->ctl = 0; + ddesc->status = DCLEAN; + } + } + priv->tx_slot = 0; + priv->tx_dirty = 0; +} + +/* Clean the RX ring */ +static void sun8i_emac_rx_clean(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int i; + struct dma_desc *ddesc; + + /* clean RX ring */ + for (i = 0; i < priv->nbdesc_rx; i++) + if (priv->rx_skb[i]) { + ddesc = priv->dd_rx + i; + dma_unmap_single(priv->dev, + le32_to_cpu(ddesc->buf_addr), + DESC_BUF_MAX, DMA_FROM_DEVICE); + dev_kfree_skb_any(priv->rx_skb[i]); + priv->rx_skb[i] = NULL; + } +} + +static int sun8i_emac_stop(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + napi_disable(&priv->napi); + + sun8i_emac_stop_tx(ndev); + sun8i_emac_stop_rx(ndev); + + phy_stop(ndev->phydev); + phy_disconnect(ndev->phydev); + + sun8i_emac_mdio_unregister(ndev); + + sun8i_emac_unset_syscon(ndev); + + free_irq(priv->irq, ndev); + + sun8i_emac_rx_clean(ndev); + sun8i_emac_tx_clean(ndev); + + kfree(priv->rx_skb); + kfree(priv->txl); + + dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc), + priv->dd_rx, priv->dd_rx_phy); + dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), + priv->dd_tx, priv->dd_tx_phy); + + return 0; +} + +static netdev_tx_t sun8i_emac_xmit(struct sk_buff *skb, struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct dma_desc *ddesc; + struct dma_desc *first; + int i = 0, rbd_first; + unsigned int len, fraglen, tlen; + u32 v; + int n; + int nf; + const skb_frag_t *frag; + int do_csum = 0; + + if (skb_put_padto(skb, ETH_ZLEN)) + return NETDEV_TX_OK; + len = skb_headlen(skb); + + n = skb_shinfo(skb)->nr_frags; + + if (skb->ip_summed == CHECKSUM_PARTIAL) { + do_csum = 1; + priv->estats.tx_hw_csum++; + } + netif_dbg(priv, tx_queued, ndev, "%s len=%u skblen=%u %x\n", __func__, + len, skb->len, + (skb->ip_summed == CHECKSUM_PARTIAL)); + + /* check for contigous space + * We need at least 1(skb->data) + n(numfrags) + 1(one clean slot) + */ + if (rb_tx_numfreedesc(ndev) < n + 2) { + dev_err_ratelimited(priv->dev, "BUG!: TX is full %d %d\n", + priv->tx_dirty, priv->tx_slot); + netif_stop_queue(ndev); + return NETDEV_TX_BUSY; + } + i = priv->tx_slot; + + ddesc = priv->dd_tx + i; + first = priv->dd_tx + i; + rbd_first = i; + + ddesc->buf_addr = dma_map_single(priv->dev, skb->data, len, + DMA_TO_DEVICE); + if (dma_mapping_error(priv->dev, ddesc->buf_addr)) { + dev_err(priv->dev, "ERROR: Cannot map buffer for DMA\n"); + goto xmit_error; + } + /* We cannot direcly use cpu_to_le32() after dma_map_single + * since dma_mapping_error use it + */ + ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr); + priv->txl[i].map = MAP_SINGLE; + priv->txl[i].skb = skb; + + tlen = len; + ddesc->ctl = le32_to_cpu(len); + /* Undocumented bit that make it works + * Without it, packets never be sent on H3 SoC + */ + ddesc->ctl |= EMAC_MAGIC_TX_BIT; + if (do_csum) + ddesc->ctl |= EMAC_TX_DO_CRC; + + /* handle fragmented skb, one descriptor per fragment */ + for (nf = 0; nf < n; nf++) { + frag = &skb_shinfo(skb)->frags[nf]; + rb_inc(&i, priv->nbdesc_tx); + priv->txl[i].skb = skb; + ddesc = priv->dd_tx + i; + fraglen = skb_frag_size(frag); + ddesc->ctl = le32_to_cpu(fraglen); + tlen += fraglen, + ddesc->ctl |= EMAC_MAGIC_TX_BIT; + if (do_csum) + ddesc->ctl |= EMAC_TX_DO_CRC; + + ddesc->buf_addr = skb_frag_dma_map(priv->dev, frag, 0, + fraglen, DMA_TO_DEVICE); + if (dma_mapping_error(priv->dev, ddesc->buf_addr)) { + dev_err(priv->dev, "Cannot map buffer for DMA\n"); + goto xmit_error; + } + /* Cannot directly use cpu_to_le32() after skb_frag_dma_map + * since dma_mapping_error use it + */ + ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr); + priv->txl[i].map = MAP_PAGE; + ddesc->status = EMAC_COULD_BE_USED_BY_DMA; + } + + /* frame end */ + ddesc->ctl |= EMAC_DSC_TX_LAST; + /* We want an interrupt after transmission */ + ddesc->ctl |= EMAC_WANT_INT; + + rb_inc(&i, priv->nbdesc_tx); + + /* frame begin */ + first->ctl |= EMAC_DSC_TX_FIRST; + wmb();/* EMAC_COULD_BE_USED_BY_DMA must be the last value written */ + first->status = EMAC_COULD_BE_USED_BY_DMA; + priv->tx_slot = i; + + /* Trying to optimize this (recording DMA start/stop) seems + * to lead to errors. So we always start DMA. + */ + v = readl(priv->base + EMAC_TX_CTL1); + v |= EMAC_TX_DMA_START; + v |= EMAC_TX_DMA_EN; + writel_relaxed(v, priv->base + EMAC_TX_CTL1); + + netdev_sent_queue(ndev, skb->len); + + if (rb_tx_numfreedesc(ndev) < MAX_SKB_FRAGS + 1) { + netif_stop_queue(ndev); + priv->estats.tx_stop_queue++; + } + priv->estats.tx_used_desc = rb_tx_numfreedesc(ndev); + priv->ndev->stats.tx_packets++; + priv->ndev->stats.tx_bytes += tlen; + + return NETDEV_TX_OK; + +xmit_error: + /* destroy skb and return TX OK Documentation/DMA-API-HOWTO.txt */ + /* clean descritors from rbd_first to i */ + ddesc->ctl = 0; + /* setting status to DCLEAN is the last value to be set */ + wmb(); + ddesc->status = DCLEAN; + do { + ddesc = priv->dd_tx + rbd_first; + ddesc->ctl = 0; + /* setting status to DCLEAN is the last value to be set */ + wmb(); + ddesc->status = DCLEAN; + rb_inc(&rbd_first, priv->nbdesc_tx); + } while (rbd_first != i); + dev_kfree_skb_any(skb); + return NETDEV_TX_OK; +} + +static int sun8i_emac_change_mtu(struct net_device *ndev, int new_mtu) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int max_mtu; + + dev_info(priv->dev, "%s set MTU to %d\n", __func__, new_mtu); + + if (netif_running(ndev)) { + dev_err(priv->dev, "%s: must be stopped to change its MTU\n", + ndev->name); + return -EBUSY; + } + + max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN); + + if ((new_mtu < 68) || (new_mtu > max_mtu)) { + dev_err(priv->dev, "%s: invalid MTU, max MTU is: %d\n", + ndev->name, max_mtu); + return -EINVAL; + } + + ndev->mtu = new_mtu; + netdev_update_features(ndev); + return 0; +} + +static int sun8i_emac_set_features(struct net_device *ndev, + netdev_features_t features) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v; + + v = readl(priv->base + EMAC_BASIC_CTL0); + if (features & NETIF_F_LOOPBACK && netif_running(ndev)) { + netif_info(priv, hw, ndev, "Set loopback features"); + v |= BIT(1); + } else { + netif_info(priv, hw, ndev, "Unset loopback features"); + v &= ~BIT(1); + } + writel(v, priv->base + EMAC_BASIC_CTL0); + + v = readl(priv->base + EMAC_RX_CTL0); + if (features & NETIF_F_RXCSUM) { + v |= EMAC_RX_DO_CRC; + netif_info(priv, hw, ndev, "Doing RX CRC check by hardware"); + } else { + v &= ~EMAC_RX_DO_CRC; + netif_info(priv, hw, ndev, "No RX CRC check by hardware"); + } + if (features & NETIF_F_RXFCS) { + v &= ~EMAC_RX_STRIP_FCS; + netif_info(priv, hw, ndev, "Keep FCS"); + } else { + v |= EMAC_RX_STRIP_FCS; + netif_info(priv, hw, ndev, "Strip FCS"); + } + writel(v, priv->base + EMAC_RX_CTL0); + + netif_dbg(priv, drv, ndev, "%s %llx %x\n", __func__, features, v); + + return 0; +} + +static void sun8i_emac_set_rx_mode(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v = 0; + int i = 0; + struct netdev_hw_addr *ha; + + /* Receive all multicast frames */ + v |= BIT(16); + /* Receive all control frames */ + v |= BIT(13); + if (ndev->flags & IFF_PROMISC) + v |= BIT(1); + if (netdev_uc_count(ndev) > 7) { + v |= BIT(1); + } else { + netdev_for_each_uc_addr(ha, ndev) { + i++; + sun8i_emac_set_macaddr(priv, ha->addr, i); + } + } + writel(v, priv->base + EMAC_RX_FRM_FLT); +} + +static void sun8i_emac_tx_timeout(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + netdev_err(ndev, "%s\n", __func__); + + sun8i_emac_stop_tx(ndev); + + sun8i_emac_tx_clean(ndev); + + /* write start of the new TX ring descriptor */ + writel(priv->dd_tx_phy, priv->base + EMAC_TX_DESC_LIST); + + sun8i_emac_start_tx(ndev); + + netdev_reset_queue(ndev); + + priv->estats.tx_timeout++; + ndev->stats.tx_errors++; + netif_wake_queue(ndev); +} + +static int sun8i_emac_ioctl(struct net_device *ndev, struct ifreq *rq, int cmd) +{ + struct phy_device *phydev = ndev->phydev; + + if (!netif_running(ndev)) + return -EINVAL; + + if (!phydev) + return -ENODEV; + + return phy_mii_ioctl(phydev, rq, cmd); +} + +static int sun8i_emac_check_if_running(struct net_device *ndev) +{ + if (!netif_running(ndev)) + return -EINVAL; + return 0; +} + +static int sun8i_emac_get_sset_count(struct net_device *ndev, int sset) +{ + switch (sset) { + case ETH_SS_STATS: + return ARRAY_SIZE(estats_str); + } + return -EOPNOTSUPP; +} + +static int sun8i_emac_ethtool_get_settings(struct net_device *ndev, + struct ethtool_cmd *cmd) +{ + struct phy_device *phy = ndev->phydev; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + if (!phy) { + netdev_err(ndev, "%s: %s: PHY is not registered\n", + __func__, ndev->name); + return -ENODEV; + } + + if (!netif_running(ndev)) { + dev_err(priv->dev, "interface disabled: we cannot track link speed / duplex setting\n"); + return -EBUSY; + } + + return phy_ethtool_gset(phy, cmd); +} + +static int sun8i_emac_ethtool_set_settings(struct net_device *ndev, + struct ethtool_cmd *cmd) +{ + struct phy_device *phy = ndev->phydev; + + return phy_ethtool_sset(phy, cmd); +} + +static void sun8i_emac_ethtool_getdrvinfo(struct net_device *ndev, + struct ethtool_drvinfo *info) +{ + strlcpy(info->driver, "sun8i_emac", sizeof(info->driver)); + strcpy(info->version, "00"); + info->fw_version[0] = '\0'; +} + +static void sun8i_emac_ethtool_stats(struct net_device *ndev, + struct ethtool_stats *dummy, u64 *data) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + memcpy(data, &priv->estats, + sun8i_emac_get_sset_count(ndev, ETH_SS_STATS) * sizeof(u64)); +} + +static void sun8i_emac_ethtool_strings(struct net_device *dev, u32 stringset, + u8 *buffer) +{ + switch (stringset) { + case ETH_SS_STATS: + memcpy(buffer, &estats_str, sizeof(estats_str)); + break; + } +} + +static u32 sun8i_emac_ethtool_getmsglevel(struct net_device *ndev) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + return priv->msg_enable; +} + +static void sun8i_emac_ethtool_setmsglevel(struct net_device *ndev, u32 level) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + priv->msg_enable = level; +} + +static void sun8i_emac_get_pauseparam(struct net_device *ndev, + struct ethtool_pauseparam *pause) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + pause->rx_pause = 0; + pause->tx_pause = 0; + pause->autoneg = ndev->phydev->autoneg; + + if (priv->flow_ctrl & EMAC_FLOW_RX) + pause->rx_pause = 1; + if (priv->flow_ctrl & EMAC_FLOW_TX) + pause->tx_pause = 1; +} + +static int sun8i_emac_set_pauseparam(struct net_device *ndev, + struct ethtool_pauseparam *pause) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + struct phy_device *phy = ndev->phydev; + int new_pause = 0; + int ret = 0; + + if (pause->rx_pause) + new_pause |= EMAC_FLOW_RX; + if (pause->tx_pause) + new_pause |= EMAC_FLOW_TX; + + priv->flow_ctrl = new_pause; + phy->autoneg = pause->autoneg; + + if (phy->autoneg) { + if (netif_running(ndev)) + ret = phy_start_aneg(phy); + } else { + sun8i_emac_flow_ctrl(priv, phy->duplex, priv->flow_ctrl); + } + return ret; +} + +static void sun8i_emac_ethtool_get_ringparam(struct net_device *ndev, + struct ethtool_ringparam *ring) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + ring->rx_pending = priv->nbdesc_rx; + ring->tx_pending = priv->nbdesc_tx; +} + +static int sun8i_emac_ethtool_set_ringparam(struct net_device *ndev, + struct ethtool_ringparam *ring) +{ + struct sun8i_emac_priv *priv = netdev_priv(ndev); + int err; + + if (ring->rx_max_pending || ring->rx_mini_max_pending || + ring->rx_jumbo_max_pending || ring->rx_mini_pending || + ring->rx_jumbo_pending || ring->tx_max_pending) + return -EINVAL; + + if (ring->tx_pending < MAX_SKB_FRAGS + 1) { + netdev_err(ndev, "The number of TX descriptors is too low"); + return -EINVAL; + } + + sun8i_emac_stop_tx(ndev); + sun8i_emac_stop_rx(ndev); + + sun8i_emac_rx_clean(ndev); + sun8i_emac_tx_clean(ndev); + + kfree(priv->rx_skb); + kfree(priv->txl); + + dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc), + priv->dd_rx, priv->dd_rx_phy); + dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), + priv->dd_tx, priv->dd_tx_phy); + + priv->nbdesc_rx = ring->rx_pending; + priv->nbdesc_tx = ring->tx_pending; + err = sun8i_emac_alloc_rings(ndev); + if (err) { + /* Fatal error, we cannot re start */ + netdev_err(ndev, "Fail to allocate rings\n"); + return -EFAULT; + } + + sun8i_emac_start_rx(ndev); + sun8i_emac_start_tx(ndev); + + netif_start_queue(ndev); + + netdev_info(ndev, "Ring Param settings: rx: %d, tx %d\n", + ring->rx_pending, ring->tx_pending); + return 0; +} + +static const struct ethtool_ops sun8i_emac_ethtool_ops = { + .begin = sun8i_emac_check_if_running, + .get_settings = sun8i_emac_ethtool_get_settings, + .set_settings = sun8i_emac_ethtool_set_settings, + .get_link = ethtool_op_get_link, + .get_pauseparam = sun8i_emac_get_pauseparam, + .set_pauseparam = sun8i_emac_set_pauseparam, + .get_ethtool_stats = sun8i_emac_ethtool_stats, + .get_strings = sun8i_emac_ethtool_strings, + .get_sset_count = sun8i_emac_get_sset_count, + .get_drvinfo = sun8i_emac_ethtool_getdrvinfo, + .get_msglevel = sun8i_emac_ethtool_getmsglevel, + .set_msglevel = sun8i_emac_ethtool_setmsglevel, + .get_ringparam = sun8i_emac_ethtool_get_ringparam, + .set_ringparam = sun8i_emac_ethtool_set_ringparam, +}; + +static const struct net_device_ops sun8i_emac_netdev_ops = { + .ndo_init = sun8i_emac_init, + .ndo_uninit = sun8i_emac_uninit, + .ndo_open = sun8i_emac_open, + .ndo_start_xmit = sun8i_emac_xmit, + .ndo_stop = sun8i_emac_stop, + .ndo_change_mtu = sun8i_emac_change_mtu, + .ndo_set_features = sun8i_emac_set_features, + .ndo_set_rx_mode = sun8i_emac_set_rx_mode, + .ndo_tx_timeout = sun8i_emac_tx_timeout, + .ndo_do_ioctl = sun8i_emac_ioctl, + .ndo_set_mac_address = eth_mac_addr, +}; + +/* No locking in this function since it is guaranteed to be run once and + * do actions only done here: + * - Scheduling NAPI + * - Stopping interrupts + * - Updating stats + * + * Even when not enabled via EMAC_INT_EN, some interrupt could fire, so we need + * to handle all of them. + * Interrupts know to fire when not enabled are: + * - EMAC_TX_DMA_STOP_INT + * - EMAC_TX_BUF_UA_INT + * - EMAC_TX_EARLY_INT + * - EMAC_RX_BUF_UA_INT + * - EMAC_RX_EARLY_INT + */ +static irqreturn_t sun8i_emac_dma_interrupt(int irq, void *dev_id) +{ + struct net_device *ndev = dev_id; + struct sun8i_emac_priv *priv = netdev_priv(ndev); + u32 v, u; + + v = readl(priv->base + EMAC_INT_STA); + + /* When this bit is asserted, a frame transmission is completed. */ + if (v & EMAC_TX_INT) { + priv->estats.tx_int++; + writel(0, priv->base + EMAC_INT_EN); + napi_schedule(&priv->napi); + } + + /* When this bit is asserted, the TX DMA FSM is stopped. + * For the moment only a call to tx_timeout cause this interrupt + * to fire. + */ + if (v & EMAC_TX_DMA_STOP_INT) + priv->estats.tx_dma_stop++; + + /* When this asserted, the TX DMA can not acquire next TX descriptor + * and TX DMA FSM is suspended. + */ + if (v & EMAC_TX_BUF_UA_INT) { + priv->estats.tx_dma_ua++; + writel(0, priv->base + EMAC_INT_EN); + napi_schedule(&priv->napi); + } + + if (v & EMAC_TX_TIMEOUT_INT) + priv->estats.tx_timeout_int++; + + if (v & EMAC_TX_UNDERFLOW_INT) + priv->estats.tx_underflow_int++; + + /* When this bit asserted , the frame is transmitted to FIFO totally. */ + if (v & EMAC_TX_EARLY_INT) + priv->estats.tx_early_int++; + + /* When this bit is asserted, a frame reception is completed */ + if (v & EMAC_RX_INT) { + priv->estats.rx_int++; + writel(0, priv->base + EMAC_INT_EN); + napi_schedule(&priv->napi); + } + + /* When this asserted, the RX DMA can not acquire next RX descriptor + * and RX DMA FSM is suspended. + */ + if (v & EMAC_RX_BUF_UA_INT) { + u = readl(priv->base + EMAC_RX_CTL1); + writel(u | EMAC_RX_DMA_START, priv->base + EMAC_RX_CTL1); + priv->estats.rx_dma_ua++; + } + + /* Same as TX DMA STOP, but never hit it */ + if (v & EMAC_RX_DMA_STOP_INT) + priv->estats.rx_dma_stop++; + + if (v & EMAC_RX_TIMEOUT_INT) + priv->estats.rx_timeout_int++; + + if (v & EMAC_RX_OVERFLOW_INT) + priv->estats.rx_overflow_int++; + + if (v & EMAC_RX_EARLY_INT) + priv->estats.rx_early_int++; + + if (v & EMAC_RGMII_STA_INT) + priv->estats.rgmii_state_int++; + + /* the datasheet state those register as read-only + * but nothing work(freeze) without writing to it + */ + writel(v, priv->base + EMAC_INT_STA); + + return IRQ_HANDLED; +} + +static int sun8i_emac_probe(struct platform_device *pdev) +{ + struct device_node *node = pdev->dev.of_node; + struct sun8i_emac_priv *priv; + struct net_device *ndev; + struct resource *res; + int ret; + + ndev = alloc_etherdev(sizeof(*priv)); + if (!ndev) + return -ENOMEM; + + SET_NETDEV_DEV(ndev, &pdev->dev); + priv = netdev_priv(ndev); + platform_set_drvdata(pdev, ndev); + + priv->variant = of_device_get_match_data(&pdev->dev); + if (!priv->variant) { + dev_err(&pdev->dev, "Missing sun8i-emac variant\n"); + return -EINVAL; + } + + priv->phy_node = of_parse_phandle(node, "phy", 0); + if (!priv->phy_node) { + netdev_err(ndev, "No associated PHY\n"); + return -ENODEV; + } + + priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, + "syscon"); + if (IS_ERR(priv->regmap)) { + ret = PTR_ERR(priv->regmap); + dev_err(&pdev->dev, "unable to map SYSCON:%d\n", ret); + return ret; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) { + ret = PTR_ERR(priv->base); + dev_err(&pdev->dev, "Cannot request MMIO: %d\n", ret); + return ret; + } + + priv->ahb_clk = devm_clk_get(&pdev->dev, "ahb"); + if (IS_ERR(priv->ahb_clk)) { + ret = PTR_ERR(priv->ahb_clk); + dev_err(&pdev->dev, "Cannot get AHB clock err=%d\n", ret); + goto probe_err; + } + + priv->rst_mac = devm_reset_control_get_optional(&pdev->dev, "ahb"); + if (IS_ERR(priv->rst_mac)) { + ret = PTR_ERR(priv->rst_mac); + if (ret == -EPROBE_DEFER) + return -EPROBE_DEFER; + dev_info(&pdev->dev, "No MAC reset control found %d\n", ret); + priv->rst_mac = NULL; + } + + priv->phy_interface = of_get_phy_mode(node); + if (priv->phy_interface < 0) { + netdev_err(ndev, "PHY interface mode node unspecified\n"); + return priv->phy_interface; + } + + switch (priv->phy_interface) { + case PHY_INTERFACE_MODE_MII: + if (!priv->variant->support_mii) + return -EINVAL; + break; + case PHY_INTERFACE_MODE_RMII: + if (!priv->variant->support_rmii) + return -EINVAL; + break; + case PHY_INTERFACE_MODE_RGMII: + if (!priv->variant->support_rgmii) + return -EINVAL; + break; + default: + netdev_err(ndev, "Unsupported interface mode: %s", + phy_modes(priv->phy_interface)); + return -EINVAL; + } + + if (priv->phy_interface == priv->variant->internal_phy) + priv->use_internal_phy = true; + + if (priv->use_internal_phy) { + priv->ephy_clk = devm_clk_get(&pdev->dev, "ephy"); + if (IS_ERR(priv->ephy_clk)) { + ret = PTR_ERR(priv->ephy_clk); + dev_err(&pdev->dev, "Cannot get EPHY clock err=%d\n", + ret); + goto probe_err; + } + + priv->rst_ephy = devm_reset_control_get_optional(&pdev->dev, + "ephy"); + if (IS_ERR(priv->rst_ephy)) { + ret = PTR_ERR(priv->rst_ephy); + if (ret == -EPROBE_DEFER) + goto probe_err; + dev_info(&pdev->dev, + "No EPHY reset control found %d\n", ret); + priv->rst_ephy = NULL; + } + } + + priv->irq = platform_get_irq(pdev, 0); + if (priv->irq < 0) { + ret = priv->irq; + dev_err(&pdev->dev, "Cannot claim IRQ: %d\n", ret); + goto probe_err; + } + + spin_lock_init(&priv->tx_lock); + + ndev->netdev_ops = &sun8i_emac_netdev_ops; + ndev->ethtool_ops = &sun8i_emac_ethtool_ops; + + priv->ndev = ndev; + priv->dev = &pdev->dev; + + ndev->hw_features = NETIF_F_SG | NETIF_F_HIGHDMA; + ndev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM | + NETIF_F_RXCSUM; + ndev->features |= ndev->hw_features; + ndev->hw_features |= NETIF_F_RXFCS; + ndev->hw_features |= NETIF_F_RXALL; + ndev->hw_features |= NETIF_F_LOOPBACK; + ndev->priv_flags |= IFF_UNICAST_FLT; + + ndev->watchdog_timeo = msecs_to_jiffies(5000); + netif_carrier_off(ndev); + + /* Benched on OPIPC with 100M, setting more than 256 does not give any + * perf boost + */ + priv->nbdesc_rx = 128; + priv->nbdesc_tx = 256; + + ret = register_netdev(ndev); + if (ret) { + dev_err(&pdev->dev, "ERROR: Register %s failed\n", ndev->name); + goto probe_err; + } + + return 0; + +probe_err: + free_netdev(ndev); + return ret; +} + +static int sun8i_emac_remove(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + + unregister_netdev(ndev); + platform_set_drvdata(pdev, NULL); + free_netdev(ndev); + + return 0; +} + +static const struct of_device_id sun8i_emac_of_match_table[] = { + { .compatible = "allwinner,sun8i-a83t-emac", + .data = &emac_variant_a83t }, + { .compatible = "allwinner,sun8i-h3-emac", + .data = &emac_variant_h3 }, + { .compatible = "allwinner,sun50i-a64-emac", + .data = &emac_variant_a64 }, + {} +}; +MODULE_DEVICE_TABLE(of, sun8i_emac_of_match_table); + +static struct platform_driver sun8i_emac_driver = { + .probe = sun8i_emac_probe, + .remove = sun8i_emac_remove, + .driver = { + .name = "sun8i-emac", + .of_match_table = sun8i_emac_of_match_table, + }, +}; + +module_platform_driver(sun8i_emac_driver); + +MODULE_DESCRIPTION("sun8i Ethernet driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com"); -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* Re: [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-09 14:15 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:15 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree Hi Corentin > +static int sun8i_emac_mdio_register(struct net_device *ndev) > +{ > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + struct mii_bus *bus; > + int ret; > + > + bus = mdiobus_alloc(); You can use devm_mdiobus_alloc() which will simplify your error handling and unregister code. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-09 14:15 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:15 UTC (permalink / raw) To: linux-arm-kernel Hi Corentin > +static int sun8i_emac_mdio_register(struct net_device *ndev) > +{ > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + struct mii_bus *bus; > + int ret; > + > + bus = mdiobus_alloc(); You can use devm_mdiobus_alloc() which will simplify your error handling and unregister code. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-09 14:15 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:15 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree-u79uwXL29TY76Z2rM5mHXA Hi Corentin > +static int sun8i_emac_mdio_register(struct net_device *ndev) > +{ > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + struct mii_bus *bus; > + int ret; > + > + bus = mdiobus_alloc(); You can use devm_mdiobus_alloc() which will simplify your error handling and unregister code. Andrew -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-13 13:33 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:33 UTC (permalink / raw) To: Andrew Lunn Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree On Fri, Sep 09, 2016 at 04:15:27PM +0200, Andrew Lunn wrote: > Hi Corentin > > > +static int sun8i_emac_mdio_register(struct net_device *ndev) > > +{ > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + struct mii_bus *bus; > > + int ret; > > + > > + bus = mdiobus_alloc(); > > You can use devm_mdiobus_alloc() which will simplify your error > handling and unregister code. > > Andrew Hello Since the mdio bus is allocated on ndev/open, it need to be removed when ndev/stop is called. So devm_mdiobus_alloc cannot be used. Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-13 13:33 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:33 UTC (permalink / raw) To: linux-arm-kernel On Fri, Sep 09, 2016 at 04:15:27PM +0200, Andrew Lunn wrote: > Hi Corentin > > > +static int sun8i_emac_mdio_register(struct net_device *ndev) > > +{ > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + struct mii_bus *bus; > > + int ret; > > + > > + bus = mdiobus_alloc(); > > You can use devm_mdiobus_alloc() which will simplify your error > handling and unregister code. > > Andrew Hello Since the mdio bus is allocated on ndev/open, it need to be removed when ndev/stop is called. So devm_mdiobus_alloc cannot be used. Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 1/9] ethernet: add sun8i-emac driver @ 2016-09-13 13:33 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:33 UTC (permalink / raw) To: Andrew Lunn Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree-u79uwXL29TY76Z2rM5mHXA On Fri, Sep 09, 2016 at 04:15:27PM +0200, Andrew Lunn wrote: > Hi Corentin > > > +static int sun8i_emac_mdio_register(struct net_device *ndev) > > +{ > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + struct mii_bus *bus; > > + int ret; > > + > > + bus = mdiobus_alloc(); > > You can use devm_mdiobus_alloc() which will simplify your error > handling and unregister code. > > Andrew Hello Since the mdio bus is allocated on ndev/open, it need to be removed when ndev/stop is called. So devm_mdiobus_alloc cannot be used. Regards Corentin Labbe -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 2/9] MAINTAINERS: Add myself as maintainer of sun8i-emac 2016-09-09 12:45 ` Corentin Labbe (?) @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe This patch add myself as maintainer of the sun8i-emac driver. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- MAINTAINERS | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 6781a3f..43f5be3 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -582,6 +582,12 @@ S: Maintained F: Documentation/i2c/busses/i2c-ali1563 F: drivers/i2c/busses/i2c-ali1563.c +ALLWINNER SUN8I-EMAC ETHERNET DRIVER +M: Corentin Labbe <clabbe.montjoie@gmail.com> +L: netdev@vger.kernel.org +S: Maintained +F: drivers/net/ethernet/allwinner/sun8i-emac.c + ALLWINNER SECURITY SYSTEM M: Corentin Labbe <clabbe.montjoie@gmail.com> L: linux-crypto@vger.kernel.org -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 2/9] MAINTAINERS: Add myself as maintainer of sun8i-emac @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel This patch add myself as maintainer of the sun8i-emac driver. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- MAINTAINERS | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 6781a3f..43f5be3 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -582,6 +582,12 @@ S: Maintained F: Documentation/i2c/busses/i2c-ali1563 F: drivers/i2c/busses/i2c-ali1563.c +ALLWINNER SUN8I-EMAC ETHERNET DRIVER +M: Corentin Labbe <clabbe.montjoie@gmail.com> +L: netdev at vger.kernel.org +S: Maintained +F: drivers/net/ethernet/allwinner/sun8i-emac.c + ALLWINNER SECURITY SYSTEM M: Corentin Labbe <clabbe.montjoie@gmail.com> L: linux-crypto at vger.kernel.org -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 2/9] MAINTAINERS: Add myself as maintainer of sun8i-emac @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, Corentin Labbe, linux-kernel, linux-arm-kernel, devicetree This patch add myself as maintainer of the sun8i-emac driver. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- MAINTAINERS | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 6781a3f..43f5be3 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -582,6 +582,12 @@ S: Maintained F: Documentation/i2c/busses/i2c-ali1563 F: drivers/i2c/busses/i2c-ali1563.c +ALLWINNER SUN8I-EMAC ETHERNET DRIVER +M: Corentin Labbe <clabbe.montjoie@gmail.com> +L: netdev@vger.kernel.org +S: Maintained +F: drivers/net/ethernet/allwinner/sun8i-emac.c + ALLWINNER SECURITY SYSTEM M: Corentin Labbe <clabbe.montjoie@gmail.com> L: linux-crypto@vger.kernel.org -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe This patch adds documentation for Device-Tree bindings for the Allwinner sun8i-emac driver. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- .../bindings/net/allwinner,sun8i-emac.txt | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt new file mode 100644 index 0000000..4968ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt @@ -0,0 +1,64 @@ +* Allwinner sun8i EMAC ethernet controller + +Required properties: +- compatible: should be one of the following string: + "allwinner,sun8i-a83t-emac" + "allwinner,sun8i-h3-emac" + "allwinner,sun50i-a64-emac" +- reg: address and length of the register for the device. +- reg-names: should be "emac" +- syscon: A phandle to the syscon of the SoC +- interrupts: interrupt for the device +- clocks: A phandle to the reference clock for this device +- clock-names: should be "ahb" +- resets: A phandle to the reset control for this device +- reset-names: should be "ahb" +- phy-mode: See ethernet.txt +- phy or phy-handle: See ethernet.txt +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +"allwinner,sun8i-h3-emac" also requires: +- clocks: an extra phandle to the reference clock for the EPHY +- clock-names: an extra "ephy" entry matching the clocks property +- resets: an extra phandle to the reset control for the EPHY +- resets-names: an extra "ephy" entry matching the resets property + +See ethernet.txt in the same directory for generic bindings for ethernet +controllers. + +The device node referenced by "phy" or "phy-handle" should be a child node +of this node. See phy.txt for the generic PHY bindings. + +Optional properties: +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) + +The TX/RX clock delay chain settings are board specific. + +Optional properties for "allwinner,sun8i-h3-emac": +- allwinner,leds-active-low: EPHY LEDs are active low + +Example: + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + reg-names = "emac"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; + reset-names = "ahb", "ephy"; + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; + clock-names = "ahb", "ephy"; + #address-cells = <1>; + #size-cells = <0>; + + phy = <&phy1>; + phy-mode = "mii"; + allwinner,leds-active-low; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel This patch adds documentation for Device-Tree bindings for the Allwinner sun8i-emac driver. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- .../bindings/net/allwinner,sun8i-emac.txt | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt new file mode 100644 index 0000000..4968ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt @@ -0,0 +1,64 @@ +* Allwinner sun8i EMAC ethernet controller + +Required properties: +- compatible: should be one of the following string: + "allwinner,sun8i-a83t-emac" + "allwinner,sun8i-h3-emac" + "allwinner,sun50i-a64-emac" +- reg: address and length of the register for the device. +- reg-names: should be "emac" +- syscon: A phandle to the syscon of the SoC +- interrupts: interrupt for the device +- clocks: A phandle to the reference clock for this device +- clock-names: should be "ahb" +- resets: A phandle to the reset control for this device +- reset-names: should be "ahb" +- phy-mode: See ethernet.txt +- phy or phy-handle: See ethernet.txt +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +"allwinner,sun8i-h3-emac" also requires: +- clocks: an extra phandle to the reference clock for the EPHY +- clock-names: an extra "ephy" entry matching the clocks property +- resets: an extra phandle to the reset control for the EPHY +- resets-names: an extra "ephy" entry matching the resets property + +See ethernet.txt in the same directory for generic bindings for ethernet +controllers. + +The device node referenced by "phy" or "phy-handle" should be a child node +of this node. See phy.txt for the generic PHY bindings. + +Optional properties: +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) + +The TX/RX clock delay chain settings are board specific. + +Optional properties for "allwinner,sun8i-h3-emac": +- allwinner,leds-active-low: EPHY LEDs are active low + +Example: + +emac: ethernet at 01c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + reg-names = "emac"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; + reset-names = "ahb", "ephy"; + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; + clock-names = "ahb", "ephy"; + #address-cells = <1>; + #size-cells = <0>; + + phy = <&phy1>; + phy-mode = "mii"; + allwinner,leds-active-low; + + phy1: ethernet-phy at 1 { + reg = <1>; + }; +}; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-09 14:04 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:04 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree > +The device node referenced by "phy" or "phy-handle" should be a child node > +of this node. See phy.txt for the generic PHY bindings. I've not looked at the code yet, but is this really true? Generally there is not this limitation. You can point to any Ethernet phy anyway, so long as it is on am MDIO bus. > + > +Optional properties: > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > + > +The TX/RX clock delay chain settings are board specific. > + > +Optional properties for "allwinner,sun8i-h3-emac": > +- allwinner,leds-active-low: EPHY LEDs are active low > + > +Example: > + > +emac: ethernet@01c0b000 { > + compatible = "allwinner,sun8i-h3-emac"; > + syscon = <&syscon>; > + reg = <0x01c0b000 0x104>; > + reg-names = "emac"; > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; > + reset-names = "ahb", "ephy"; > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > + clock-names = "ahb", "ephy"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + phy = <&phy1>; ethernet.txt say: - phy: the same as "phy-handle" property, not recommended for new bindings. This is a new binding, please don't support it. > + phy-mode = "mii"; > + allwinner,leds-active-low; > + > + phy1: ethernet-phy@1 { > + reg = <1>; > + }; It is normal to place these phy nodes inside an container node called mdio. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-09 14:04 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:04 UTC (permalink / raw) To: linux-arm-kernel > +The device node referenced by "phy" or "phy-handle" should be a child node > +of this node. See phy.txt for the generic PHY bindings. I've not looked at the code yet, but is this really true? Generally there is not this limitation. You can point to any Ethernet phy anyway, so long as it is on am MDIO bus. > + > +Optional properties: > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > + > +The TX/RX clock delay chain settings are board specific. > + > +Optional properties for "allwinner,sun8i-h3-emac": > +- allwinner,leds-active-low: EPHY LEDs are active low > + > +Example: > + > +emac: ethernet at 01c0b000 { > + compatible = "allwinner,sun8i-h3-emac"; > + syscon = <&syscon>; > + reg = <0x01c0b000 0x104>; > + reg-names = "emac"; > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; > + reset-names = "ahb", "ephy"; > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > + clock-names = "ahb", "ephy"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + phy = <&phy1>; ethernet.txt say: - phy: the same as "phy-handle" property, not recommended for new bindings. This is a new binding, please don't support it. > + phy-mode = "mii"; > + allwinner,leds-active-low; > + > + phy1: ethernet-phy at 1 { > + reg = <1>; > + }; It is normal to place these phy nodes inside an container node called mdio. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-09 14:04 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:04 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree-u79uwXL29TY76Z2rM5mHXA > +The device node referenced by "phy" or "phy-handle" should be a child node > +of this node. See phy.txt for the generic PHY bindings. I've not looked at the code yet, but is this really true? Generally there is not this limitation. You can point to any Ethernet phy anyway, so long as it is on am MDIO bus. > + > +Optional properties: > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > + > +The TX/RX clock delay chain settings are board specific. > + > +Optional properties for "allwinner,sun8i-h3-emac": > +- allwinner,leds-active-low: EPHY LEDs are active low > + > +Example: > + > +emac: ethernet@01c0b000 { > + compatible = "allwinner,sun8i-h3-emac"; > + syscon = <&syscon>; > + reg = <0x01c0b000 0x104>; > + reg-names = "emac"; > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; > + reset-names = "ahb", "ephy"; > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > + clock-names = "ahb", "ephy"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + phy = <&phy1>; ethernet.txt say: - phy: the same as "phy-handle" property, not recommended for new bindings. This is a new binding, please don't support it. > + phy-mode = "mii"; > + allwinner,leds-active-low; > + > + phy1: ethernet-phy@1 { > + reg = <1>; > + }; It is normal to place these phy nodes inside an container node called mdio. Andrew -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac 2016-09-09 14:04 ` Andrew Lunn @ 2016-09-12 15:01 ` LABBE Corentin -1 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-12 15:01 UTC (permalink / raw) To: Andrew Lunn Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree On Fri, Sep 09, 2016 at 04:04:13PM +0200, Andrew Lunn wrote: > > +The device node referenced by "phy" or "phy-handle" should be a child node > > +of this node. See phy.txt for the generic PHY bindings. > > I've not looked at the code yet, but is this really true? Generally > there is not this limitation. You can point to any Ethernet phy > anyway, so long as it is on am MDIO bus. > > > + > > +Optional properties: > > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > > + > > +The TX/RX clock delay chain settings are board specific. > > + > > +Optional properties for "allwinner,sun8i-h3-emac": > > +- allwinner,leds-active-low: EPHY LEDs are active low > > + > > +Example: > > + > > +emac: ethernet@01c0b000 { > > + compatible = "allwinner,sun8i-h3-emac"; > > + syscon = <&syscon>; > > + reg = <0x01c0b000 0x104>; > > + reg-names = "emac"; > > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > > + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; > > + reset-names = "ahb", "ephy"; > > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > > + clock-names = "ahb", "ephy"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + phy = <&phy1>; > > ethernet.txt say: > > - phy: the same as "phy-handle" property, not recommended for new bindings. > > This is a new binding, please don't support it. > > > + phy-mode = "mii"; > > + allwinner,leds-active-low; > > + > > + phy1: ethernet-phy@1 { > > + reg = <1>; > > + }; > > It is normal to place these phy nodes inside an container node called > mdio. > Hello Since the MDIO bus is a part of the sun8i-emac, does I really need to create such a mdio node ? All example I found are mdio bus with separate driver. (others driver have the phy directly in [eg]mac node. Anyway I try the following patch to solve your comments, but it breaks the PHY finding(Could not attach to PHY). Regards -->8-- --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -166,14 +166,18 @@ status = "okay"; }; +&mdio { + reg = <1>; + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + &emac { - phy = <&phy1>; + phy-handle = <&phy1>; phy-mode = "mii"; allwinner,leds-active-low; status = "okay"; - phy1: ethernet-phy@1 { - reg = <1>; - }; };/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -474,6 +474,11 @@ #address-cells = <1>; #size-cells = <0>; status = "disabled"; + + mdio: mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + }; }; crypto: crypto@1c15000 { --- a/drivers/net/ethernet/allwinner/sun8i-emac.c +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c @@ -2122,7 +2122,7 @@ static int sun8i_emac_probe(struct platform_device *pdev) return -EINVAL; } - priv->phy_node = of_parse_phandle(node, "phy", 0); + priv->phy_node = of_parse_phandle(node, "phy-handle", 0); if (!priv->phy_node) { netdev_err(ndev, "No associated PHY\n"); return -ENODEV; &crypto { ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-12 15:01 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-12 15:01 UTC (permalink / raw) To: linux-arm-kernel On Fri, Sep 09, 2016 at 04:04:13PM +0200, Andrew Lunn wrote: > > +The device node referenced by "phy" or "phy-handle" should be a child node > > +of this node. See phy.txt for the generic PHY bindings. > > I've not looked at the code yet, but is this really true? Generally > there is not this limitation. You can point to any Ethernet phy > anyway, so long as it is on am MDIO bus. > > > + > > +Optional properties: > > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > > + > > +The TX/RX clock delay chain settings are board specific. > > + > > +Optional properties for "allwinner,sun8i-h3-emac": > > +- allwinner,leds-active-low: EPHY LEDs are active low > > + > > +Example: > > + > > +emac: ethernet at 01c0b000 { > > + compatible = "allwinner,sun8i-h3-emac"; > > + syscon = <&syscon>; > > + reg = <0x01c0b000 0x104>; > > + reg-names = "emac"; > > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > > + resets = <&ccu RST_BUS_EMAC>, <<&ccu RST_BUS_EPHY>; > > + reset-names = "ahb", "ephy"; > > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > > + clock-names = "ahb", "ephy"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + phy = <&phy1>; > > ethernet.txt say: > > - phy: the same as "phy-handle" property, not recommended for new bindings. > > This is a new binding, please don't support it. > > > + phy-mode = "mii"; > > + allwinner,leds-active-low; > > + > > + phy1: ethernet-phy at 1 { > > + reg = <1>; > > + }; > > It is normal to place these phy nodes inside an container node called > mdio. > Hello Since the MDIO bus is a part of the sun8i-emac, does I really need to create such a mdio node ? All example I found are mdio bus with separate driver. (others driver have the phy directly in [eg]mac node. Anyway I try the following patch to solve your comments, but it breaks the PHY finding(Could not attach to PHY). Regards -->8-- --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -166,14 +166,18 @@ status = "okay"; }; +&mdio { + reg = <1>; + phy1: ethernet-phy at 1 { + reg = <1>; + }; +}; + &emac { - phy = <&phy1>; + phy-handle = <&phy1>; phy-mode = "mii"; allwinner,leds-active-low; status = "okay"; - phy1: ethernet-phy at 1 { - reg = <1>; - }; };/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -474,6 +474,11 @@ #address-cells = <1>; #size-cells = <0>; status = "disabled"; + + mdio: mdio at 0 { + #address-cells = <1>; + #size-cells = <0>; + }; }; crypto: crypto at 1c15000 { --- a/drivers/net/ethernet/allwinner/sun8i-emac.c +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c @@ -2122,7 +2122,7 @@ static int sun8i_emac_probe(struct platform_device *pdev) return -EINVAL; } - priv->phy_node = of_parse_phandle(node, "phy", 0); + priv->phy_node = of_parse_phandle(node, "phy-handle", 0); if (!priv->phy_node) { netdev_err(ndev, "No associated PHY\n"); return -ENODEV; &crypto { ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac 2016-09-12 15:01 ` LABBE Corentin @ 2016-09-12 15:15 ` Andrew Lunn -1 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-12 15:15 UTC (permalink / raw) To: LABBE Corentin Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree > Hello > > Since the MDIO bus is a part of the sun8i-emac, does I really need > to create such a mdio node ? It is good practice. Part of the issue is that there are no written guidelines, so different drivers do different things. I'm trying to push all new drivers to have an MDIO node. > Anyway I try the following patch to solve your comments, but it > breaks the PHY finding(Could not attach to PHY). > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > @@ -2122,7 +2122,7 @@ static int sun8i_emac_probe(struct platform_device *pdev) > return -EINVAL; > } > > - priv->phy_node = of_parse_phandle(node, "phy", 0); > + priv->phy_node = of_parse_phandle(node, "phy-handle", 0); > if (!priv->phy_node) { > netdev_err(ndev, "No associated PHY\n"); > return -ENODEV; > > > &crypto { > I don't see a change here for of_mdiobus_register(). You need to pass the mdio node. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-12 15:15 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-12 15:15 UTC (permalink / raw) To: linux-arm-kernel > Hello > > Since the MDIO bus is a part of the sun8i-emac, does I really need > to create such a mdio node ? It is good practice. Part of the issue is that there are no written guidelines, so different drivers do different things. I'm trying to push all new drivers to have an MDIO node. > Anyway I try the following patch to solve your comments, but it > breaks the PHY finding(Could not attach to PHY). > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > @@ -2122,7 +2122,7 @@ static int sun8i_emac_probe(struct platform_device *pdev) > return -EINVAL; > } > > - priv->phy_node = of_parse_phandle(node, "phy", 0); > + priv->phy_node = of_parse_phandle(node, "phy-handle", 0); > if (!priv->phy_node) { > netdev_err(ndev, "No associated PHY\n"); > return -ENODEV; > > > &crypto { > I don't see a change here for of_mdiobus_register(). You need to pass the mdio node. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 14:17 ` Andrew Lunn -1 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:17 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree > +Optional properties: > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) What are the units? pS? nS? Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-09 14:17 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-09 14:17 UTC (permalink / raw) To: linux-arm-kernel > +Optional properties: > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) What are the units? pS? nS? Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac 2016-09-09 14:17 ` Andrew Lunn @ 2016-09-13 13:34 ` LABBE Corentin -1 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:34 UTC (permalink / raw) To: Andrew Lunn Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree On Fri, Sep 09, 2016 at 04:17:10PM +0200, Andrew Lunn wrote: > > +Optional properties: > > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > > What are the units? pS? nS? > > Andrew No units, only raw number. I will add a comment for this. Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-13 13:34 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:34 UTC (permalink / raw) To: linux-arm-kernel On Fri, Sep 09, 2016 at 04:17:10PM +0200, Andrew Lunn wrote: > > +Optional properties: > > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > > What are the units? pS? nS? > > Andrew No units, only raw number. I will add a comment for this. Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac 2016-09-13 13:34 ` LABBE Corentin @ 2016-09-13 14:12 ` Andrew Lunn -1 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-13 14:12 UTC (permalink / raw) To: LABBE Corentin Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem, netdev, linux-kernel, linux-arm-kernel, devicetree On Tue, Sep 13, 2016 at 03:34:17PM +0200, LABBE Corentin wrote: > On Fri, Sep 09, 2016 at 04:17:10PM +0200, Andrew Lunn wrote: > > > +Optional properties: > > > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > > > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > > > > What are the units? pS? nS? > > > > Andrew > > No units, only raw number. > I will add a comment for this. And it is likely it will get NACKed by the device tree maintainers. You should use real unit here. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac @ 2016-09-13 14:12 ` Andrew Lunn 0 siblings, 0 replies; 71+ messages in thread From: Andrew Lunn @ 2016-09-13 14:12 UTC (permalink / raw) To: linux-arm-kernel On Tue, Sep 13, 2016 at 03:34:17PM +0200, LABBE Corentin wrote: > On Fri, Sep 09, 2016 at 04:17:10PM +0200, Andrew Lunn wrote: > > > +Optional properties: > > > +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0) > > > +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0) > > > > What are the units? pS? nS? > > > > Andrew > > No units, only raw number. > I will add a comment for this. And it is likely it will get NACKed by the device tree maintainers. You should use real unit here. Andrew ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe This patch add the dt node for the syscon register present on the Allwinner H3. Only two register are present in this syscon and the only one useful is the one dedicated to EMAC clock. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index fdf9fdb..a39da6f 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -140,6 +140,11 @@ #size-cells = <1>; ranges; + syscon: syscon@01c00000 { + compatible = "syscon"; + reg = <0x01c00000 0x34>; + }; + dma: dma-controller@01c02000 { compatible = "allwinner,sun8i-h3-dma"; reg = <0x01c02000 0x1000>; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel This patch add the dt node for the syscon register present on the Allwinner H3. Only two register are present in this syscon and the only one useful is the one dedicated to EMAC clock. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index fdf9fdb..a39da6f 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -140,6 +140,11 @@ #size-cells = <1>; ranges; + syscon: syscon at 01c00000 { + compatible = "syscon"; + reg = <0x01c00000 0x34>; + }; + dma: dma-controller at 01c02000 { compatible = "allwinner,sun8i-h3-dma"; reg = <0x01c02000 0x1000>; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q Cc: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA, Corentin Labbe This patch add the dt node for the syscon register present on the Allwinner H3. Only two register are present in this syscon and the only one useful is the one dedicated to EMAC clock. Signed-off-by: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> --- arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index fdf9fdb..a39da6f 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -140,6 +140,11 @@ #size-cells = <1>; ranges; + syscon: syscon@01c00000 { + compatible = "syscon"; + reg = <0x01c00000 0x34>; + }; + dma: dma-controller@01c02000 { compatible = "allwinner,sun8i-h3-dma"; reg = <0x01c02000 0x1000>; -- 2.7.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 71+ messages in thread
* Re: [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-12 7:28 ` Maxime Ripard -1 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:28 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 1036 bytes --] On Fri, Sep 09, 2016 at 02:45:12PM +0200, Corentin Labbe wrote: > This patch add the dt node for the syscon register present on the > Allwinner H3. > > Only two register are present in this syscon and the only one useful is > the one dedicated to EMAC clock. > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > --- > arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > index fdf9fdb..a39da6f 100644 > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > @@ -140,6 +140,11 @@ > #size-cells = <1>; > ranges; > > + syscon: syscon@01c00000 { > + compatible = "syscon"; Having our compatible would be nice here. syscon doesn't mean anything by itself. > + reg = <0x01c00000 0x34>; And the size of our system controller is 0x1000 Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module @ 2016-09-12 7:28 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:28 UTC (permalink / raw) To: linux-arm-kernel On Fri, Sep 09, 2016 at 02:45:12PM +0200, Corentin Labbe wrote: > This patch add the dt node for the syscon register present on the > Allwinner H3. > > Only two register are present in this syscon and the only one useful is > the one dedicated to EMAC clock. > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > --- > arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > index fdf9fdb..a39da6f 100644 > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > @@ -140,6 +140,11 @@ > #size-cells = <1>; > ranges; > > + syscon: syscon at 01c00000 { > + compatible = "syscon"; Having our compatible would be nice here. syscon doesn't mean anything by itself. > + reg = <0x01c00000 0x34>; And the size of our system controller is 0x1000 Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160912/b888ced4/attachment.sig> ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module 2016-09-12 7:28 ` Maxime Ripard (?) @ 2016-09-13 13:38 ` LABBE Corentin -1 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:38 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel On Mon, Sep 12, 2016 at 09:28:12AM +0200, Maxime Ripard wrote: > On Fri, Sep 09, 2016 at 02:45:12PM +0200, Corentin Labbe wrote: > > This patch add the dt node for the syscon register present on the > > Allwinner H3. > > > > Only two register are present in this syscon and the only one useful is > > the one dedicated to EMAC clock. > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > --- > > arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ > > 1 file changed, 5 insertions(+) > > > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > > index fdf9fdb..a39da6f 100644 > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > > @@ -140,6 +140,11 @@ > > #size-cells = <1>; > > ranges; > > > > + syscon: syscon@01c00000 { > > + compatible = "syscon"; > > Having our compatible would be nice here. syscon doesn't mean anything > by itself. > Since no driver handle it, I follow what I saw in other DT. At your choice, I can add a sun8i-syscon, but it will be unused. > > + reg = <0x01c00000 0x34>; > > And the size of our system controller is 0x1000 > I put the real size used, but I can put what datasheet said. Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module @ 2016-09-13 13:38 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:38 UTC (permalink / raw) To: linux-arm-kernel On Mon, Sep 12, 2016 at 09:28:12AM +0200, Maxime Ripard wrote: > On Fri, Sep 09, 2016 at 02:45:12PM +0200, Corentin Labbe wrote: > > This patch add the dt node for the syscon register present on the > > Allwinner H3. > > > > Only two register are present in this syscon and the only one useful is > > the one dedicated to EMAC clock. > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > --- > > arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ > > 1 file changed, 5 insertions(+) > > > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > > index fdf9fdb..a39da6f 100644 > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > > @@ -140,6 +140,11 @@ > > #size-cells = <1>; > > ranges; > > > > + syscon: syscon at 01c00000 { > > + compatible = "syscon"; > > Having our compatible would be nice here. syscon doesn't mean anything > by itself. > Since no driver handle it, I follow what I saw in other DT. At your choice, I can add a sun8i-syscon, but it will be unused. > > + reg = <0x01c00000 0x34>; > > And the size of our system controller is 0x1000 > I put the real size used, but I can put what datasheet said. Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module @ 2016-09-13 13:38 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:38 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Mon, Sep 12, 2016 at 09:28:12AM +0200, Maxime Ripard wrote: > On Fri, Sep 09, 2016 at 02:45:12PM +0200, Corentin Labbe wrote: > > This patch add the dt node for the syscon register present on the > > Allwinner H3. > > > > Only two register are present in this syscon and the only one useful is > > the one dedicated to EMAC clock. > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > > --- > > arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++ > > 1 file changed, 5 insertions(+) > > > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > > index fdf9fdb..a39da6f 100644 > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > > @@ -140,6 +140,11 @@ > > #size-cells = <1>; > > ranges; > > > > + syscon: syscon@01c00000 { > > + compatible = "syscon"; > > Having our compatible would be nice here. syscon doesn't mean anything > by itself. > Since no driver handle it, I follow what I saw in other DT. At your choice, I can add a sun8i-syscon, but it will be unused. > > + reg = <0x01c00000 0x34>; > > And the size of our system controller is 0x1000 > I put the real size used, but I can put what datasheet said. Regards Corentin Labbe -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 speed. This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. The SoC H3 have an internal PHY, so optionals syscon and ephy are set. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index a39da6f..a3ac476 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -50,6 +50,10 @@ / { interrupt-parent = <&gic>; + aliases { + ethernet0 = &emac; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -446,6 +450,21 @@ status = "disabled"; }; + emac: ethernet@1c30000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c30000 0x104>; + reg-names = "emac"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; + reset-names = "ahb", "ephy"; + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; + clock-names = "ahb", "ephy"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@01c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 speed. This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. The SoC H3 have an internal PHY, so optionals syscon and ephy are set. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index a39da6f..a3ac476 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -50,6 +50,10 @@ / { interrupt-parent = <&gic>; + aliases { + ethernet0 = &emac; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -446,6 +450,21 @@ status = "disabled"; }; + emac: ethernet at 1c30000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c30000 0x104>; + reg-names = "emac"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; + reset-names = "ahb", "ephy"; + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; + clock-names = "ahb", "ephy"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller at 01c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* Re: [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver @ 2016-09-12 7:29 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:29 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 1611 bytes --] On Fri, Sep 09, 2016 at 02:45:13PM +0200, Corentin Labbe wrote: > The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 > speed. > > This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. > The SoC H3 have an internal PHY, so optionals syscon and ephy are set. > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > --- > arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ > 1 file changed, 19 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > index a39da6f..a3ac476 100644 > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > @@ -50,6 +50,10 @@ > / { > interrupt-parent = <&gic>; > > + aliases { > + ethernet0 = &emac; > + }; > + This needs to be done at the board level. > cpus { > #address-cells = <1>; > #size-cells = <0>; > @@ -446,6 +450,21 @@ > status = "disabled"; > }; > > + emac: ethernet@1c30000 { > + compatible = "allwinner,sun8i-h3-emac"; > + syscon = <&syscon>; > + reg = <0x01c30000 0x104>; > + reg-names = "emac"; You don't need reg-names anymore. > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; > + reset-names = "ahb", "ephy"; > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > + clock-names = "ahb", "ephy"; I still believe that having the same node for both the PHY and the MAC is wrong. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver @ 2016-09-12 7:29 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:29 UTC (permalink / raw) To: linux-arm-kernel On Fri, Sep 09, 2016 at 02:45:13PM +0200, Corentin Labbe wrote: > The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 > speed. > > This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. > The SoC H3 have an internal PHY, so optionals syscon and ephy are set. > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > --- > arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ > 1 file changed, 19 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > index a39da6f..a3ac476 100644 > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > @@ -50,6 +50,10 @@ > / { > interrupt-parent = <&gic>; > > + aliases { > + ethernet0 = &emac; > + }; > + This needs to be done at the board level. > cpus { > #address-cells = <1>; > #size-cells = <0>; > @@ -446,6 +450,21 @@ > status = "disabled"; > }; > > + emac: ethernet at 1c30000 { > + compatible = "allwinner,sun8i-h3-emac"; > + syscon = <&syscon>; > + reg = <0x01c30000 0x104>; > + reg-names = "emac"; You don't need reg-names anymore. > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; > + reset-names = "ahb", "ephy"; > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > + clock-names = "ahb", "ephy"; I still believe that having the same node for both the PHY and the MAC is wrong. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160912/011b2815/attachment.sig> ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver @ 2016-09-12 7:29 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:29 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA [-- Attachment #1: Type: text/plain, Size: 1641 bytes --] On Fri, Sep 09, 2016 at 02:45:13PM +0200, Corentin Labbe wrote: > The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 > speed. > > This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. > The SoC H3 have an internal PHY, so optionals syscon and ephy are set. > > Signed-off-by: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > --- > arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ > 1 file changed, 19 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > index a39da6f..a3ac476 100644 > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > @@ -50,6 +50,10 @@ > / { > interrupt-parent = <&gic>; > > + aliases { > + ethernet0 = &emac; > + }; > + This needs to be done at the board level. > cpus { > #address-cells = <1>; > #size-cells = <0>; > @@ -446,6 +450,21 @@ > status = "disabled"; > }; > > + emac: ethernet@1c30000 { > + compatible = "allwinner,sun8i-h3-emac"; > + syscon = <&syscon>; > + reg = <0x01c30000 0x104>; > + reg-names = "emac"; You don't need reg-names anymore. > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; > + reset-names = "ahb", "ephy"; > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > + clock-names = "ahb", "ephy"; I still believe that having the same node for both the PHY and the MAC is wrong. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver 2016-09-12 7:29 ` Maxime Ripard @ 2016-09-14 8:54 ` LABBE Corentin -1 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-14 8:54 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel On Mon, Sep 12, 2016 at 09:29:33AM +0200, Maxime Ripard wrote: > On Fri, Sep 09, 2016 at 02:45:13PM +0200, Corentin Labbe wrote: > > The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 > > speed. > > > > This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. > > The SoC H3 have an internal PHY, so optionals syscon and ephy are set. > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > --- > > arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ > > 1 file changed, 19 insertions(+) > > > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > > index a39da6f..a3ac476 100644 > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > > @@ -50,6 +50,10 @@ > > / { > > interrupt-parent = <&gic>; > > > > + aliases { > > + ethernet0 = &emac; > > + }; > > + > > This needs to be done at the board level. > ok > > cpus { > > #address-cells = <1>; > > #size-cells = <0>; > > @@ -446,6 +450,21 @@ > > status = "disabled"; > > }; > > > > + emac: ethernet@1c30000 { > > + compatible = "allwinner,sun8i-h3-emac"; > > + syscon = <&syscon>; > > + reg = <0x01c30000 0x104>; > > + reg-names = "emac"; > > You don't need reg-names anymore. > ok > > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > > + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; > > + reset-names = "ahb", "ephy"; > > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > > + clock-names = "ahb", "ephy"; > > I still believe that having the same node for both the PHY and the MAC > is wrong. > Ok I have moved clock/reset of ephy in its node. Thanks Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver @ 2016-09-14 8:54 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-14 8:54 UTC (permalink / raw) To: linux-arm-kernel On Mon, Sep 12, 2016 at 09:29:33AM +0200, Maxime Ripard wrote: > On Fri, Sep 09, 2016 at 02:45:13PM +0200, Corentin Labbe wrote: > > The sun8i-emac is an ethernet MAC hardware that support 10/100/1000 > > speed. > > > > This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree. > > The SoC H3 have an internal PHY, so optionals syscon and ephy are set. > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > --- > > arch/arm/boot/dts/sun8i-h3.dtsi | 19 +++++++++++++++++++ > > 1 file changed, 19 insertions(+) > > > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > > index a39da6f..a3ac476 100644 > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > > @@ -50,6 +50,10 @@ > > / { > > interrupt-parent = <&gic>; > > > > + aliases { > > + ethernet0 = &emac; > > + }; > > + > > This needs to be done at the board level. > ok > > cpus { > > #address-cells = <1>; > > #size-cells = <0>; > > @@ -446,6 +450,21 @@ > > status = "disabled"; > > }; > > > > + emac: ethernet at 1c30000 { > > + compatible = "allwinner,sun8i-h3-emac"; > > + syscon = <&syscon>; > > + reg = <0x01c30000 0x104>; > > + reg-names = "emac"; > > You don't need reg-names anymore. > ok > > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > > + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; > > + reset-names = "ahb", "ephy"; > > + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; > > + clock-names = "ahb", "ephy"; > > I still believe that having the same node for both the PHY and the MAC > is wrong. > Ok I have moved clock/reset of ephy in its node. Thanks Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 6/9] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI PC 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe The sun8i-emac hardware is present on the Orange PI PC. It uses the internal PHY. This patch create the needed emac and phy nodes. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index daf50b9a6..24f8e97 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -165,3 +165,13 @@ /* USB VBUS is always on */ status = "okay"; }; + +&emac { + phy = <&phy1>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 6/9] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI PC @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel The sun8i-emac hardware is present on the Orange PI PC. It uses the internal PHY. This patch create the needed emac and phy nodes. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index daf50b9a6..24f8e97 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -165,3 +165,13 @@ /* USB VBUS is always on */ status = "okay"; }; + +&emac { + phy = <&phy1>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; + phy1: ethernet-phy at 1 { + reg = <1>; + }; +}; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 7/9] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI One 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Hans de Goede, Corentin Labbe From: Hans de Goede <hdegoede@redhat.com> The sun8i-emac hardware is present on the Orange PI One. It uses the internal PHY. This patch create the needed emac and phy nodes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 0adf932..0bc3867 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -94,6 +94,16 @@ status = "okay"; }; +&emac { + phy = <&phy1>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 7/9] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI One @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel From: Hans de Goede <hdegoede@redhat.com> The sun8i-emac hardware is present on the Orange PI One. It uses the internal PHY. This patch create the needed emac and phy nodes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 0adf932..0bc3867 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -94,6 +94,16 @@ status = "okay"; }; +&emac { + phy = <&phy1>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; + phy1: ethernet-phy at 1 { + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe Enable the sun8i-emac driver in the sunxi default configuration Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/configs/sunxi_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig index 714da33..153707a 100644 --- a/arch/arm/configs/sunxi_defconfig +++ b/arch/arm/configs/sunxi_defconfig @@ -40,6 +40,7 @@ CONFIG_ATA=y CONFIG_AHCI_SUNXI=y CONFIG_NETDEVICES=y CONFIG_SUN4I_EMAC=y +CONFIG_SUN8I_EMAC=y # CONFIG_NET_VENDOR_ARC is not set # CONFIG_NET_CADENCE is not set # CONFIG_NET_VENDOR_BROADCOM is not set -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel Enable the sun8i-emac driver in the sunxi default configuration Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- arch/arm/configs/sunxi_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig index 714da33..153707a 100644 --- a/arch/arm/configs/sunxi_defconfig +++ b/arch/arm/configs/sunxi_defconfig @@ -40,6 +40,7 @@ CONFIG_ATA=y CONFIG_AHCI_SUNXI=y CONFIG_NETDEVICES=y CONFIG_SUN4I_EMAC=y +CONFIG_SUN8I_EMAC=y # CONFIG_NET_VENDOR_ARC is not set # CONFIG_NET_CADENCE is not set # CONFIG_NET_VENDOR_BROADCOM is not set -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* Re: [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig @ 2016-09-12 7:30 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:30 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 375 bytes --] Hi, On Fri, Sep 09, 2016 at 02:45:16PM +0200, Corentin Labbe wrote: > Enable the sun8i-emac driver in the sunxi default configuration > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Could you make the same patch for multi_v7 ? Thanks, Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig @ 2016-09-12 7:30 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:30 UTC (permalink / raw) To: linux-arm-kernel Hi, On Fri, Sep 09, 2016 at 02:45:16PM +0200, Corentin Labbe wrote: > Enable the sun8i-emac driver in the sunxi default configuration > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Could you make the same patch for multi_v7 ? Thanks, Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160912/d62daa8b/attachment-0001.sig> ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig @ 2016-09-12 7:30 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 7:30 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA [-- Attachment #1: Type: text/plain, Size: 405 bytes --] Hi, On Fri, Sep 09, 2016 at 02:45:16PM +0200, Corentin Labbe wrote: > Enable the sun8i-emac driver in the sunxi default configuration > > Signed-off-by: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> Could you make the same patch for multi_v7 ? Thanks, Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig 2016-09-12 7:30 ` Maxime Ripard (?) @ 2016-09-13 13:42 ` LABBE Corentin -1 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:42 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel On Mon, Sep 12, 2016 at 09:30:08AM +0200, Maxime Ripard wrote: > Hi, > > On Fri, Sep 09, 2016 at 02:45:16PM +0200, Corentin Labbe wrote: > > Enable the sun8i-emac driver in the sunxi default configuration > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > Could you make the same patch for multi_v7 ? > I will Thanks ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig @ 2016-09-13 13:42 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:42 UTC (permalink / raw) To: linux-arm-kernel On Mon, Sep 12, 2016 at 09:30:08AM +0200, Maxime Ripard wrote: > Hi, > > On Fri, Sep 09, 2016 at 02:45:16PM +0200, Corentin Labbe wrote: > > Enable the sun8i-emac driver in the sunxi default configuration > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > Could you make the same patch for multi_v7 ? > I will Thanks ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig @ 2016-09-13 13:42 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-13 13:42 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Mon, Sep 12, 2016 at 09:30:08AM +0200, Maxime Ripard wrote: > Hi, > > On Fri, Sep 09, 2016 at 02:45:16PM +0200, Corentin Labbe wrote: > > Enable the sun8i-emac driver in the sunxi default configuration > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > > Could you make the same patch for multi_v7 ? > I will Thanks -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-09 12:45 ` Corentin Labbe -1 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: robh+dt, mark.rutland, maxime.ripard, wens, linux, davem Cc: netdev, devicetree, linux-arm-kernel, linux-kernel, Corentin Labbe This patch add pm_runtime support to sun8i-emac. For the moment, only basic support is added, (the device is marked as used when net/open) Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- 1 file changed, 60 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c index 1c4bc80..cce886e 100644 --- a/drivers/net/ethernet/allwinner/sun8i-emac.c +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c @@ -9,7 +9,6 @@ * - MAC filtering * - Jumbo frame * - features rx-all (NETIF_F_RXALL_BIT) - * - PM runtime */ #include <linux/bitops.h> #include <linux/clk.h> @@ -27,6 +26,7 @@ #include <linux/pinctrl/consumer.h> #include <linux/pinctrl/pinctrl.h> #include <linux/platform_device.h> +#include <linux/pm_runtime.h> #include <linux/reset.h> #include <linux/scatterlist.h> #include <linux/skbuff.h> @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) int err; u32 v; + err = pm_runtime_get_sync(priv->dev); + if (err) { + pm_runtime_put_noidle(priv->dev); + dev_err(priv->dev, "pm_runtime error: %d\n", err); + return err; + } + err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, dev_name(priv->dev), ndev); if (err) { dev_err(priv->dev, "Cannot request IRQ: %d\n", err); - return err; + goto err_runtime; } /* Set interface mode (and configure internal PHY on H3) */ @@ -1395,6 +1402,8 @@ err_syscon: sun8i_emac_unset_syscon(ndev); err_irq: free_irq(priv->irq, ndev); +err_runtime: + pm_runtime_put(priv->dev); return err; } @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), priv->dd_tx, priv->dd_tx_phy); + pm_runtime_put(priv->dev); + return 0; } @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) goto probe_err; } + pm_runtime_enable(priv->dev); + return 0; probe_err: @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) { struct net_device *ndev = platform_get_drvdata(pdev); + pm_runtime_disable(&pdev->dev); + unregister_netdev(ndev); platform_set_drvdata(pdev, NULL); free_netdev(ndev); @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) return 0; } +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + napi_disable(&priv->napi); + + if (netif_running(ndev)) + netif_device_detach(ndev); + + sun8i_emac_stop_tx(ndev); + sun8i_emac_stop_rx(ndev); + + sun8i_emac_rx_clean(ndev); + sun8i_emac_tx_clean(ndev); + + phy_stop(ndev->phydev); + + return 0; +} + +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + phy_start(ndev->phydev); + + sun8i_emac_start_tx(ndev); + sun8i_emac_start_rx(ndev); + + if (netif_running(ndev)) + netif_device_attach(ndev); + + netif_start_queue(ndev); + + napi_enable(&priv->napi); + + return 0; +} + static const struct of_device_id sun8i_emac_of_match_table[] = { { .compatible = "allwinner,sun8i-a83t-emac", .data = &emac_variant_a83t }, @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { .name = "sun8i-emac", .of_match_table = sun8i_emac_of_match_table, }, + .suspend = sun8i_emac_suspend, + .resume = sun8i_emac_resume, }; module_platform_driver(sun8i_emac_driver); -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-09 12:45 ` Corentin Labbe 0 siblings, 0 replies; 71+ messages in thread From: Corentin Labbe @ 2016-09-09 12:45 UTC (permalink / raw) To: linux-arm-kernel This patch add pm_runtime support to sun8i-emac. For the moment, only basic support is added, (the device is marked as used when net/open) Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> --- drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- 1 file changed, 60 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c index 1c4bc80..cce886e 100644 --- a/drivers/net/ethernet/allwinner/sun8i-emac.c +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c @@ -9,7 +9,6 @@ * - MAC filtering * - Jumbo frame * - features rx-all (NETIF_F_RXALL_BIT) - * - PM runtime */ #include <linux/bitops.h> #include <linux/clk.h> @@ -27,6 +26,7 @@ #include <linux/pinctrl/consumer.h> #include <linux/pinctrl/pinctrl.h> #include <linux/platform_device.h> +#include <linux/pm_runtime.h> #include <linux/reset.h> #include <linux/scatterlist.h> #include <linux/skbuff.h> @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) int err; u32 v; + err = pm_runtime_get_sync(priv->dev); + if (err) { + pm_runtime_put_noidle(priv->dev); + dev_err(priv->dev, "pm_runtime error: %d\n", err); + return err; + } + err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, dev_name(priv->dev), ndev); if (err) { dev_err(priv->dev, "Cannot request IRQ: %d\n", err); - return err; + goto err_runtime; } /* Set interface mode (and configure internal PHY on H3) */ @@ -1395,6 +1402,8 @@ err_syscon: sun8i_emac_unset_syscon(ndev); err_irq: free_irq(priv->irq, ndev); +err_runtime: + pm_runtime_put(priv->dev); return err; } @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), priv->dd_tx, priv->dd_tx_phy); + pm_runtime_put(priv->dev); + return 0; } @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) goto probe_err; } + pm_runtime_enable(priv->dev); + return 0; probe_err: @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) { struct net_device *ndev = platform_get_drvdata(pdev); + pm_runtime_disable(&pdev->dev); + unregister_netdev(ndev); platform_set_drvdata(pdev, NULL); free_netdev(ndev); @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) return 0; } +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + napi_disable(&priv->napi); + + if (netif_running(ndev)) + netif_device_detach(ndev); + + sun8i_emac_stop_tx(ndev); + sun8i_emac_stop_rx(ndev); + + sun8i_emac_rx_clean(ndev); + sun8i_emac_tx_clean(ndev); + + phy_stop(ndev->phydev); + + return 0; +} + +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct sun8i_emac_priv *priv = netdev_priv(ndev); + + phy_start(ndev->phydev); + + sun8i_emac_start_tx(ndev); + sun8i_emac_start_rx(ndev); + + if (netif_running(ndev)) + netif_device_attach(ndev); + + netif_start_queue(ndev); + + napi_enable(&priv->napi); + + return 0; +} + static const struct of_device_id sun8i_emac_of_match_table[] = { { .compatible = "allwinner,sun8i-a83t-emac", .data = &emac_variant_a83t }, @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { .name = "sun8i-emac", .of_match_table = sun8i_emac_of_match_table, }, + .suspend = sun8i_emac_suspend, + .resume = sun8i_emac_resume, }; module_platform_driver(sun8i_emac_driver); -- 2.7.3 ^ permalink raw reply related [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support 2016-09-09 12:45 ` Corentin Labbe @ 2016-09-12 20:44 ` Maxime Ripard -1 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 20:44 UTC (permalink / raw) To: Corentin Labbe Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 4675 bytes --] Hi, On Fri, Sep 09, 2016 at 02:45:17PM +0200, Corentin Labbe wrote: > This patch add pm_runtime support to sun8i-emac. > For the moment, only basic support is added, (the device is marked as > used when net/open) > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > --- > drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- > 1 file changed, 60 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c > index 1c4bc80..cce886e 100644 > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > @@ -9,7 +9,6 @@ > * - MAC filtering > * - Jumbo frame > * - features rx-all (NETIF_F_RXALL_BIT) > - * - PM runtime > */ > #include <linux/bitops.h> > #include <linux/clk.h> > @@ -27,6 +26,7 @@ > #include <linux/pinctrl/consumer.h> > #include <linux/pinctrl/pinctrl.h> > #include <linux/platform_device.h> > +#include <linux/pm_runtime.h> > #include <linux/reset.h> > #include <linux/scatterlist.h> > #include <linux/skbuff.h> > @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) > int err; > u32 v; > > + err = pm_runtime_get_sync(priv->dev); > + if (err) { > + pm_runtime_put_noidle(priv->dev); > + dev_err(priv->dev, "pm_runtime error: %d\n", err); > + return err; > + } > + > err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, > dev_name(priv->dev), ndev); > if (err) { > dev_err(priv->dev, "Cannot request IRQ: %d\n", err); > - return err; > + goto err_runtime; > } > > /* Set interface mode (and configure internal PHY on H3) */ > @@ -1395,6 +1402,8 @@ err_syscon: > sun8i_emac_unset_syscon(ndev); > err_irq: > free_irq(priv->irq, ndev); > +err_runtime: > + pm_runtime_put(priv->dev); > return err; > } > > @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) > dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), > priv->dd_tx, priv->dd_tx_phy); > > + pm_runtime_put(priv->dev); > + > return 0; > } > > @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) > goto probe_err; > } > > + pm_runtime_enable(priv->dev); > + > return 0; > > probe_err: > @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) > { > struct net_device *ndev = platform_get_drvdata(pdev); > > + pm_runtime_disable(&pdev->dev); > + > unregister_netdev(ndev); > platform_set_drvdata(pdev, NULL); > free_netdev(ndev); > @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) > return 0; > } > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > +{ > + struct net_device *ndev = platform_get_drvdata(pdev); > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + > + napi_disable(&priv->napi); > + > + if (netif_running(ndev)) > + netif_device_detach(ndev); > + > + sun8i_emac_stop_tx(ndev); > + sun8i_emac_stop_rx(ndev); > + > + sun8i_emac_rx_clean(ndev); > + sun8i_emac_tx_clean(ndev); > + > + phy_stop(ndev->phydev); > + > + return 0; > +} > + > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > +{ > + struct net_device *ndev = platform_get_drvdata(pdev); > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + > + phy_start(ndev->phydev); > + > + sun8i_emac_start_tx(ndev); > + sun8i_emac_start_rx(ndev); > + > + if (netif_running(ndev)) > + netif_device_attach(ndev); > + > + netif_start_queue(ndev); > + > + napi_enable(&priv->napi); > + > + return 0; > +} The main idea behind the runtime PM hooks is that they bring the device to a working state and shuts it down when it's not needed anymore. However, they shouldn't be called when the device is still in used, so all the mangling with NAPI, the phy and so on is irrelevant here, but the clocks, resets, for example, are. > static const struct of_device_id sun8i_emac_of_match_table[] = { > { .compatible = "allwinner,sun8i-a83t-emac", > .data = &emac_variant_a83t }, > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > .name = "sun8i-emac", > .of_match_table = sun8i_emac_of_match_table, > }, > + .suspend = sun8i_emac_suspend, > + .resume = sun8i_emac_resume, These are not the runtime PM hooks. How did you test that? Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-12 20:44 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-12 20:44 UTC (permalink / raw) To: linux-arm-kernel Hi, On Fri, Sep 09, 2016 at 02:45:17PM +0200, Corentin Labbe wrote: > This patch add pm_runtime support to sun8i-emac. > For the moment, only basic support is added, (the device is marked as > used when net/open) > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > --- > drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- > 1 file changed, 60 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c > index 1c4bc80..cce886e 100644 > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > @@ -9,7 +9,6 @@ > * - MAC filtering > * - Jumbo frame > * - features rx-all (NETIF_F_RXALL_BIT) > - * - PM runtime > */ > #include <linux/bitops.h> > #include <linux/clk.h> > @@ -27,6 +26,7 @@ > #include <linux/pinctrl/consumer.h> > #include <linux/pinctrl/pinctrl.h> > #include <linux/platform_device.h> > +#include <linux/pm_runtime.h> > #include <linux/reset.h> > #include <linux/scatterlist.h> > #include <linux/skbuff.h> > @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) > int err; > u32 v; > > + err = pm_runtime_get_sync(priv->dev); > + if (err) { > + pm_runtime_put_noidle(priv->dev); > + dev_err(priv->dev, "pm_runtime error: %d\n", err); > + return err; > + } > + > err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, > dev_name(priv->dev), ndev); > if (err) { > dev_err(priv->dev, "Cannot request IRQ: %d\n", err); > - return err; > + goto err_runtime; > } > > /* Set interface mode (and configure internal PHY on H3) */ > @@ -1395,6 +1402,8 @@ err_syscon: > sun8i_emac_unset_syscon(ndev); > err_irq: > free_irq(priv->irq, ndev); > +err_runtime: > + pm_runtime_put(priv->dev); > return err; > } > > @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) > dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), > priv->dd_tx, priv->dd_tx_phy); > > + pm_runtime_put(priv->dev); > + > return 0; > } > > @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) > goto probe_err; > } > > + pm_runtime_enable(priv->dev); > + > return 0; > > probe_err: > @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) > { > struct net_device *ndev = platform_get_drvdata(pdev); > > + pm_runtime_disable(&pdev->dev); > + > unregister_netdev(ndev); > platform_set_drvdata(pdev, NULL); > free_netdev(ndev); > @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) > return 0; > } > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > +{ > + struct net_device *ndev = platform_get_drvdata(pdev); > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + > + napi_disable(&priv->napi); > + > + if (netif_running(ndev)) > + netif_device_detach(ndev); > + > + sun8i_emac_stop_tx(ndev); > + sun8i_emac_stop_rx(ndev); > + > + sun8i_emac_rx_clean(ndev); > + sun8i_emac_tx_clean(ndev); > + > + phy_stop(ndev->phydev); > + > + return 0; > +} > + > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > +{ > + struct net_device *ndev = platform_get_drvdata(pdev); > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > + > + phy_start(ndev->phydev); > + > + sun8i_emac_start_tx(ndev); > + sun8i_emac_start_rx(ndev); > + > + if (netif_running(ndev)) > + netif_device_attach(ndev); > + > + netif_start_queue(ndev); > + > + napi_enable(&priv->napi); > + > + return 0; > +} The main idea behind the runtime PM hooks is that they bring the device to a working state and shuts it down when it's not needed anymore. However, they shouldn't be called when the device is still in used, so all the mangling with NAPI, the phy and so on is irrelevant here, but the clocks, resets, for example, are. > static const struct of_device_id sun8i_emac_of_match_table[] = { > { .compatible = "allwinner,sun8i-a83t-emac", > .data = &emac_variant_a83t }, > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > .name = "sun8i-emac", > .of_match_table = sun8i_emac_of_match_table, > }, > + .suspend = sun8i_emac_suspend, > + .resume = sun8i_emac_resume, These are not the runtime PM hooks. How did you test that? Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160912/33d774be/attachment.sig> ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support 2016-09-12 20:44 ` Maxime Ripard (?) @ 2016-09-14 14:03 ` LABBE Corentin -1 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-14 14:03 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel On Mon, Sep 12, 2016 at 10:44:51PM +0200, Maxime Ripard wrote: > Hi, > > On Fri, Sep 09, 2016 at 02:45:17PM +0200, Corentin Labbe wrote: > > This patch add pm_runtime support to sun8i-emac. > > For the moment, only basic support is added, (the device is marked as > > used when net/open) > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > --- > > drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- > > 1 file changed, 60 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c > > index 1c4bc80..cce886e 100644 > > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > > @@ -9,7 +9,6 @@ > > * - MAC filtering > > * - Jumbo frame > > * - features rx-all (NETIF_F_RXALL_BIT) > > - * - PM runtime > > */ > > #include <linux/bitops.h> > > #include <linux/clk.h> > > @@ -27,6 +26,7 @@ > > #include <linux/pinctrl/consumer.h> > > #include <linux/pinctrl/pinctrl.h> > > #include <linux/platform_device.h> > > +#include <linux/pm_runtime.h> > > #include <linux/reset.h> > > #include <linux/scatterlist.h> > > #include <linux/skbuff.h> > > @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) > > int err; > > u32 v; > > > > + err = pm_runtime_get_sync(priv->dev); > > + if (err) { > > + pm_runtime_put_noidle(priv->dev); > > + dev_err(priv->dev, "pm_runtime error: %d\n", err); > > + return err; > > + } > > + > > err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, > > dev_name(priv->dev), ndev); > > if (err) { > > dev_err(priv->dev, "Cannot request IRQ: %d\n", err); > > - return err; > > + goto err_runtime; > > } > > > > /* Set interface mode (and configure internal PHY on H3) */ > > @@ -1395,6 +1402,8 @@ err_syscon: > > sun8i_emac_unset_syscon(ndev); > > err_irq: > > free_irq(priv->irq, ndev); > > +err_runtime: > > + pm_runtime_put(priv->dev); > > return err; > > } > > > > @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) > > dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), > > priv->dd_tx, priv->dd_tx_phy); > > > > + pm_runtime_put(priv->dev); > > + > > return 0; > > } > > > > @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) > > goto probe_err; > > } > > > > + pm_runtime_enable(priv->dev); > > + > > return 0; > > > > probe_err: > > @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) > > { > > struct net_device *ndev = platform_get_drvdata(pdev); > > > > + pm_runtime_disable(&pdev->dev); > > + > > unregister_netdev(ndev); > > platform_set_drvdata(pdev, NULL); > > free_netdev(ndev); > > @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) > > return 0; > > } > > > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > > +{ > > + struct net_device *ndev = platform_get_drvdata(pdev); > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + > > + napi_disable(&priv->napi); > > + > > + if (netif_running(ndev)) > > + netif_device_detach(ndev); > > + > > + sun8i_emac_stop_tx(ndev); > > + sun8i_emac_stop_rx(ndev); > > + > > + sun8i_emac_rx_clean(ndev); > > + sun8i_emac_tx_clean(ndev); > > + > > + phy_stop(ndev->phydev); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > > +{ > > + struct net_device *ndev = platform_get_drvdata(pdev); > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + > > + phy_start(ndev->phydev); > > + > > + sun8i_emac_start_tx(ndev); > > + sun8i_emac_start_rx(ndev); > > + > > + if (netif_running(ndev)) > > + netif_device_attach(ndev); > > + > > + netif_start_queue(ndev); > > + > > + napi_enable(&priv->napi); > > + > > + return 0; > > +} > > The main idea behind the runtime PM hooks is that they bring the > device to a working state and shuts it down when it's not needed > anymore. > I expect that the first part (all pm_runtime_xxx) of the patch bring that. When the interface is not opened: cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status suspended > However, they shouldn't be called when the device is still in used, so > all the mangling with NAPI, the phy and so on is irrelevant here, but > the clocks, resets, for example, are. > I do the same as other ethernet driver for suspend/resume. > > static const struct of_device_id sun8i_emac_of_match_table[] = { > > { .compatible = "allwinner,sun8i-a83t-emac", > > .data = &emac_variant_a83t }, > > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > > .name = "sun8i-emac", > > .of_match_table = sun8i_emac_of_match_table, > > }, > > + .suspend = sun8i_emac_suspend, > > + .resume = sun8i_emac_resume, > > These are not the runtime PM hooks. How did you test that? > Anyway I didnt test suspend/resume so I will remove it until I successfully found how to hibernate my board. Thanks Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-14 14:03 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-14 14:03 UTC (permalink / raw) To: linux-arm-kernel On Mon, Sep 12, 2016 at 10:44:51PM +0200, Maxime Ripard wrote: > Hi, > > On Fri, Sep 09, 2016 at 02:45:17PM +0200, Corentin Labbe wrote: > > This patch add pm_runtime support to sun8i-emac. > > For the moment, only basic support is added, (the device is marked as > > used when net/open) > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> > > --- > > drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- > > 1 file changed, 60 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c > > index 1c4bc80..cce886e 100644 > > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > > @@ -9,7 +9,6 @@ > > * - MAC filtering > > * - Jumbo frame > > * - features rx-all (NETIF_F_RXALL_BIT) > > - * - PM runtime > > */ > > #include <linux/bitops.h> > > #include <linux/clk.h> > > @@ -27,6 +26,7 @@ > > #include <linux/pinctrl/consumer.h> > > #include <linux/pinctrl/pinctrl.h> > > #include <linux/platform_device.h> > > +#include <linux/pm_runtime.h> > > #include <linux/reset.h> > > #include <linux/scatterlist.h> > > #include <linux/skbuff.h> > > @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) > > int err; > > u32 v; > > > > + err = pm_runtime_get_sync(priv->dev); > > + if (err) { > > + pm_runtime_put_noidle(priv->dev); > > + dev_err(priv->dev, "pm_runtime error: %d\n", err); > > + return err; > > + } > > + > > err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, > > dev_name(priv->dev), ndev); > > if (err) { > > dev_err(priv->dev, "Cannot request IRQ: %d\n", err); > > - return err; > > + goto err_runtime; > > } > > > > /* Set interface mode (and configure internal PHY on H3) */ > > @@ -1395,6 +1402,8 @@ err_syscon: > > sun8i_emac_unset_syscon(ndev); > > err_irq: > > free_irq(priv->irq, ndev); > > +err_runtime: > > + pm_runtime_put(priv->dev); > > return err; > > } > > > > @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) > > dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), > > priv->dd_tx, priv->dd_tx_phy); > > > > + pm_runtime_put(priv->dev); > > + > > return 0; > > } > > > > @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) > > goto probe_err; > > } > > > > + pm_runtime_enable(priv->dev); > > + > > return 0; > > > > probe_err: > > @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) > > { > > struct net_device *ndev = platform_get_drvdata(pdev); > > > > + pm_runtime_disable(&pdev->dev); > > + > > unregister_netdev(ndev); > > platform_set_drvdata(pdev, NULL); > > free_netdev(ndev); > > @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) > > return 0; > > } > > > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > > +{ > > + struct net_device *ndev = platform_get_drvdata(pdev); > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + > > + napi_disable(&priv->napi); > > + > > + if (netif_running(ndev)) > > + netif_device_detach(ndev); > > + > > + sun8i_emac_stop_tx(ndev); > > + sun8i_emac_stop_rx(ndev); > > + > > + sun8i_emac_rx_clean(ndev); > > + sun8i_emac_tx_clean(ndev); > > + > > + phy_stop(ndev->phydev); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > > +{ > > + struct net_device *ndev = platform_get_drvdata(pdev); > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + > > + phy_start(ndev->phydev); > > + > > + sun8i_emac_start_tx(ndev); > > + sun8i_emac_start_rx(ndev); > > + > > + if (netif_running(ndev)) > > + netif_device_attach(ndev); > > + > > + netif_start_queue(ndev); > > + > > + napi_enable(&priv->napi); > > + > > + return 0; > > +} > > The main idea behind the runtime PM hooks is that they bring the > device to a working state and shuts it down when it's not needed > anymore. > I expect that the first part (all pm_runtime_xxx) of the patch bring that. When the interface is not opened: cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status suspended > However, they shouldn't be called when the device is still in used, so > all the mangling with NAPI, the phy and so on is irrelevant here, but > the clocks, resets, for example, are. > I do the same as other ethernet driver for suspend/resume. > > static const struct of_device_id sun8i_emac_of_match_table[] = { > > { .compatible = "allwinner,sun8i-a83t-emac", > > .data = &emac_variant_a83t }, > > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > > .name = "sun8i-emac", > > .of_match_table = sun8i_emac_of_match_table, > > }, > > + .suspend = sun8i_emac_suspend, > > + .resume = sun8i_emac_resume, > > These are not the runtime PM hooks. How did you test that? > Anyway I didnt test suspend/resume so I will remove it until I successfully found how to hibernate my board. Thanks Regards Corentin Labbe ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-14 14:03 ` LABBE Corentin 0 siblings, 0 replies; 71+ messages in thread From: LABBE Corentin @ 2016-09-14 14:03 UTC (permalink / raw) To: Maxime Ripard Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Mon, Sep 12, 2016 at 10:44:51PM +0200, Maxime Ripard wrote: > Hi, > > On Fri, Sep 09, 2016 at 02:45:17PM +0200, Corentin Labbe wrote: > > This patch add pm_runtime support to sun8i-emac. > > For the moment, only basic support is added, (the device is marked as > > used when net/open) > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > > --- > > drivers/net/ethernet/allwinner/sun8i-emac.c | 62 ++++++++++++++++++++++++++++- > > 1 file changed, 60 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c > > index 1c4bc80..cce886e 100644 > > --- a/drivers/net/ethernet/allwinner/sun8i-emac.c > > +++ b/drivers/net/ethernet/allwinner/sun8i-emac.c > > @@ -9,7 +9,6 @@ > > * - MAC filtering > > * - Jumbo frame > > * - features rx-all (NETIF_F_RXALL_BIT) > > - * - PM runtime > > */ > > #include <linux/bitops.h> > > #include <linux/clk.h> > > @@ -27,6 +26,7 @@ > > #include <linux/pinctrl/consumer.h> > > #include <linux/pinctrl/pinctrl.h> > > #include <linux/platform_device.h> > > +#include <linux/pm_runtime.h> > > #include <linux/reset.h> > > #include <linux/scatterlist.h> > > #include <linux/skbuff.h> > > @@ -1301,11 +1301,18 @@ static int sun8i_emac_open(struct net_device *ndev) > > int err; > > u32 v; > > > > + err = pm_runtime_get_sync(priv->dev); > > + if (err) { > > + pm_runtime_put_noidle(priv->dev); > > + dev_err(priv->dev, "pm_runtime error: %d\n", err); > > + return err; > > + } > > + > > err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0, > > dev_name(priv->dev), ndev); > > if (err) { > > dev_err(priv->dev, "Cannot request IRQ: %d\n", err); > > - return err; > > + goto err_runtime; > > } > > > > /* Set interface mode (and configure internal PHY on H3) */ > > @@ -1395,6 +1402,8 @@ err_syscon: > > sun8i_emac_unset_syscon(ndev); > > err_irq: > > free_irq(priv->irq, ndev); > > +err_runtime: > > + pm_runtime_put(priv->dev); > > return err; > > } > > > > @@ -1483,6 +1492,8 @@ static int sun8i_emac_stop(struct net_device *ndev) > > dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc), > > priv->dd_tx, priv->dd_tx_phy); > > > > + pm_runtime_put(priv->dev); > > + > > return 0; > > } > > > > @@ -2210,6 +2221,8 @@ static int sun8i_emac_probe(struct platform_device *pdev) > > goto probe_err; > > } > > > > + pm_runtime_enable(priv->dev); > > + > > return 0; > > > > probe_err: > > @@ -2221,6 +2234,8 @@ static int sun8i_emac_remove(struct platform_device *pdev) > > { > > struct net_device *ndev = platform_get_drvdata(pdev); > > > > + pm_runtime_disable(&pdev->dev); > > + > > unregister_netdev(ndev); > > platform_set_drvdata(pdev, NULL); > > free_netdev(ndev); > > @@ -2228,6 +2243,47 @@ static int sun8i_emac_remove(struct platform_device *pdev) > > return 0; > > } > > > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > > +{ > > + struct net_device *ndev = platform_get_drvdata(pdev); > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + > > + napi_disable(&priv->napi); > > + > > + if (netif_running(ndev)) > > + netif_device_detach(ndev); > > + > > + sun8i_emac_stop_tx(ndev); > > + sun8i_emac_stop_rx(ndev); > > + > > + sun8i_emac_rx_clean(ndev); > > + sun8i_emac_tx_clean(ndev); > > + > > + phy_stop(ndev->phydev); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > > +{ > > + struct net_device *ndev = platform_get_drvdata(pdev); > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > + > > + phy_start(ndev->phydev); > > + > > + sun8i_emac_start_tx(ndev); > > + sun8i_emac_start_rx(ndev); > > + > > + if (netif_running(ndev)) > > + netif_device_attach(ndev); > > + > > + netif_start_queue(ndev); > > + > > + napi_enable(&priv->napi); > > + > > + return 0; > > +} > > The main idea behind the runtime PM hooks is that they bring the > device to a working state and shuts it down when it's not needed > anymore. > I expect that the first part (all pm_runtime_xxx) of the patch bring that. When the interface is not opened: cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status suspended > However, they shouldn't be called when the device is still in used, so > all the mangling with NAPI, the phy and so on is irrelevant here, but > the clocks, resets, for example, are. > I do the same as other ethernet driver for suspend/resume. > > static const struct of_device_id sun8i_emac_of_match_table[] = { > > { .compatible = "allwinner,sun8i-a83t-emac", > > .data = &emac_variant_a83t }, > > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > > .name = "sun8i-emac", > > .of_match_table = sun8i_emac_of_match_table, > > }, > > + .suspend = sun8i_emac_suspend, > > + .resume = sun8i_emac_resume, > > These are not the runtime PM hooks. How did you test that? > Anyway I didnt test suspend/resume so I will remove it until I successfully found how to hibernate my board. Thanks Regards Corentin Labbe -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support 2016-09-14 14:03 ` LABBE Corentin (?) @ 2016-09-17 13:40 ` Maxime Ripard -1 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-17 13:40 UTC (permalink / raw) To: LABBE Corentin Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 2980 bytes --] On Wed, Sep 14, 2016 at 04:03:04PM +0200, LABBE Corentin wrote: > > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > > > +{ > > > + struct net_device *ndev = platform_get_drvdata(pdev); > > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > > + > > > + napi_disable(&priv->napi); > > > + > > > + if (netif_running(ndev)) > > > + netif_device_detach(ndev); > > > + > > > + sun8i_emac_stop_tx(ndev); > > > + sun8i_emac_stop_rx(ndev); > > > + > > > + sun8i_emac_rx_clean(ndev); > > > + sun8i_emac_tx_clean(ndev); > > > + > > > + phy_stop(ndev->phydev); > > > + > > > + return 0; > > > +} > > > + > > > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > > > +{ > > > + struct net_device *ndev = platform_get_drvdata(pdev); > > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > > + > > > + phy_start(ndev->phydev); > > > + > > > + sun8i_emac_start_tx(ndev); > > > + sun8i_emac_start_rx(ndev); > > > + > > > + if (netif_running(ndev)) > > > + netif_device_attach(ndev); > > > + > > > + netif_start_queue(ndev); > > > + > > > + napi_enable(&priv->napi); > > > + > > > + return 0; > > > +} > > > > The main idea behind the runtime PM hooks is that they bring the > > device to a working state and shuts it down when it's not needed > > anymore. Indeed. > I expect that the first part (all pm_runtime_xxx) of the patch bring that. > When the interface is not opened: > cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status > suspended > > > However, they shouldn't be called when the device is still in used, so > > all the mangling with NAPI, the phy and so on is irrelevant here, but > > the clocks, resets, for example, are. > > > > I do the same as other ethernet driver for suspend/resume. suspend / resume are used when you put the whole system into suspend, and bring it back. runtime_pm is only when the device is not used anymore. It makes sense when you suspend to do whatever you're doing here. It doesn't make any when the system is not suspended, but the device is. > > > static const struct of_device_id sun8i_emac_of_match_table[] = { > > > { .compatible = "allwinner,sun8i-a83t-emac", > > > .data = &emac_variant_a83t }, > > > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > > > .name = "sun8i-emac", > > > .of_match_table = sun8i_emac_of_match_table, > > > }, > > > + .suspend = sun8i_emac_suspend, > > > + .resume = sun8i_emac_resume, > > > > These are not the runtime PM hooks. How did you test that? > > > > Anyway I didnt test suspend/resume so I will remove it until I > successfully found how to hibernate my board. So you submit code you never tested? That's usually a recipe for disaster. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-17 13:40 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-17 13:40 UTC (permalink / raw) To: linux-arm-kernel On Wed, Sep 14, 2016 at 04:03:04PM +0200, LABBE Corentin wrote: > > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > > > +{ > > > + struct net_device *ndev = platform_get_drvdata(pdev); > > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > > + > > > + napi_disable(&priv->napi); > > > + > > > + if (netif_running(ndev)) > > > + netif_device_detach(ndev); > > > + > > > + sun8i_emac_stop_tx(ndev); > > > + sun8i_emac_stop_rx(ndev); > > > + > > > + sun8i_emac_rx_clean(ndev); > > > + sun8i_emac_tx_clean(ndev); > > > + > > > + phy_stop(ndev->phydev); > > > + > > > + return 0; > > > +} > > > + > > > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > > > +{ > > > + struct net_device *ndev = platform_get_drvdata(pdev); > > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > > + > > > + phy_start(ndev->phydev); > > > + > > > + sun8i_emac_start_tx(ndev); > > > + sun8i_emac_start_rx(ndev); > > > + > > > + if (netif_running(ndev)) > > > + netif_device_attach(ndev); > > > + > > > + netif_start_queue(ndev); > > > + > > > + napi_enable(&priv->napi); > > > + > > > + return 0; > > > +} > > > > The main idea behind the runtime PM hooks is that they bring the > > device to a working state and shuts it down when it's not needed > > anymore. Indeed. > I expect that the first part (all pm_runtime_xxx) of the patch bring that. > When the interface is not opened: > cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status > suspended > > > However, they shouldn't be called when the device is still in used, so > > all the mangling with NAPI, the phy and so on is irrelevant here, but > > the clocks, resets, for example, are. > > > > I do the same as other ethernet driver for suspend/resume. suspend / resume are used when you put the whole system into suspend, and bring it back. runtime_pm is only when the device is not used anymore. It makes sense when you suspend to do whatever you're doing here. It doesn't make any when the system is not suspended, but the device is. > > > static const struct of_device_id sun8i_emac_of_match_table[] = { > > > { .compatible = "allwinner,sun8i-a83t-emac", > > > .data = &emac_variant_a83t }, > > > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > > > .name = "sun8i-emac", > > > .of_match_table = sun8i_emac_of_match_table, > > > }, > > > + .suspend = sun8i_emac_suspend, > > > + .resume = sun8i_emac_resume, > > > > These are not the runtime PM hooks. How did you test that? > > > > Anyway I didnt test suspend/resume so I will remove it until I > successfully found how to hibernate my board. So you submit code you never tested? That's usually a recipe for disaster. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160917/c2f7dacb/attachment.sig> ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-17 13:40 ` Maxime Ripard 0 siblings, 0 replies; 71+ messages in thread From: Maxime Ripard @ 2016-09-17 13:40 UTC (permalink / raw) To: LABBE Corentin Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA [-- Attachment #1: Type: text/plain, Size: 2980 bytes --] On Wed, Sep 14, 2016 at 04:03:04PM +0200, LABBE Corentin wrote: > > > +static int __maybe_unused sun8i_emac_suspend(struct platform_device *pdev, pm_message_t state) > > > +{ > > > + struct net_device *ndev = platform_get_drvdata(pdev); > > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > > + > > > + napi_disable(&priv->napi); > > > + > > > + if (netif_running(ndev)) > > > + netif_device_detach(ndev); > > > + > > > + sun8i_emac_stop_tx(ndev); > > > + sun8i_emac_stop_rx(ndev); > > > + > > > + sun8i_emac_rx_clean(ndev); > > > + sun8i_emac_tx_clean(ndev); > > > + > > > + phy_stop(ndev->phydev); > > > + > > > + return 0; > > > +} > > > + > > > +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) > > > +{ > > > + struct net_device *ndev = platform_get_drvdata(pdev); > > > + struct sun8i_emac_priv *priv = netdev_priv(ndev); > > > + > > > + phy_start(ndev->phydev); > > > + > > > + sun8i_emac_start_tx(ndev); > > > + sun8i_emac_start_rx(ndev); > > > + > > > + if (netif_running(ndev)) > > > + netif_device_attach(ndev); > > > + > > > + netif_start_queue(ndev); > > > + > > > + napi_enable(&priv->napi); > > > + > > > + return 0; > > > +} > > > > The main idea behind the runtime PM hooks is that they bring the > > device to a working state and shuts it down when it's not needed > > anymore. Indeed. > I expect that the first part (all pm_runtime_xxx) of the patch bring that. > When the interface is not opened: > cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status > suspended > > > However, they shouldn't be called when the device is still in used, so > > all the mangling with NAPI, the phy and so on is irrelevant here, but > > the clocks, resets, for example, are. > > > > I do the same as other ethernet driver for suspend/resume. suspend / resume are used when you put the whole system into suspend, and bring it back. runtime_pm is only when the device is not used anymore. It makes sense when you suspend to do whatever you're doing here. It doesn't make any when the system is not suspended, but the device is. > > > static const struct of_device_id sun8i_emac_of_match_table[] = { > > > { .compatible = "allwinner,sun8i-a83t-emac", > > > .data = &emac_variant_a83t }, > > > @@ -2246,6 +2302,8 @@ static struct platform_driver sun8i_emac_driver = { > > > .name = "sun8i-emac", > > > .of_match_table = sun8i_emac_of_match_table, > > > }, > > > + .suspend = sun8i_emac_suspend, > > > + .resume = sun8i_emac_resume, > > > > These are not the runtime PM hooks. How did you test that? > > > > Anyway I didnt test suspend/resume so I will remove it until I > successfully found how to hibernate my board. So you submit code you never tested? That's usually a recipe for disaster. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 819 bytes --] ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support 2016-09-14 14:03 ` LABBE Corentin (?) @ 2016-09-17 16:50 ` Florian Fainelli -1 siblings, 0 replies; 71+ messages in thread From: Florian Fainelli @ 2016-09-17 16:50 UTC (permalink / raw) To: LABBE Corentin, Maxime Ripard Cc: robh+dt, mark.rutland, wens, linux, davem, netdev, devicetree, linux-arm-kernel, linux-kernel On 09/14/2016 07:03 AM, LABBE Corentin wrote: > On Mon, Sep 12, 2016 at 10:44:51PM +0200, Maxime Ripard wrote: >>> +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) >>> +{ >>> + struct net_device *ndev = platform_get_drvdata(pdev); >>> + struct sun8i_emac_priv *priv = netdev_priv(ndev); >>> + >>> + phy_start(ndev->phydev); >>> + >>> + sun8i_emac_start_tx(ndev); >>> + sun8i_emac_start_rx(ndev); >>> + >>> + if (netif_running(ndev)) >>> + netif_device_attach(ndev); >>> + >>> + netif_start_queue(ndev); >>> + >>> + napi_enable(&priv->napi); >>> + >>> + return 0; >>> +} >> >> The main idea behind the runtime PM hooks is that they bring the >> device to a working state and shuts it down when it's not needed >> anymore. >> > > I expect that the first part (all pm_runtime_xxx) of the patch bring that. > When the interface is not opened: > cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status > suspended If your interface is not open, it should be in a low power state, only when it gets open (which means it is used) should you make it functional, that's pretty much the same thing as the runtime PM reference count usage here. I don't see a lot of value for using runtime_pm_* hooks here except calling into the existing suspend/resume functions that you have defined already, but then again, the code should be modular enough already in the driver. Runtime PM for network devices cannot be used as efficiently as you would with any kind of host-initiated bus/controller because your device needs to be able to receive packets without the host's ability to wake up the device to receive packets, so, with the exception of MDIO (which is host initiated), everything else besides except packet transmission (then again, I would not want to wait N ms to bring the interface in a state where it can now transmit packets, that's terrible for latency) is pretty much impossible to fully suspend due to its asynchronous nature. -- Florian ^ permalink raw reply [flat|nested] 71+ messages in thread
* [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-17 16:50 ` Florian Fainelli 0 siblings, 0 replies; 71+ messages in thread From: Florian Fainelli @ 2016-09-17 16:50 UTC (permalink / raw) To: linux-arm-kernel On 09/14/2016 07:03 AM, LABBE Corentin wrote: > On Mon, Sep 12, 2016 at 10:44:51PM +0200, Maxime Ripard wrote: >>> +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) >>> +{ >>> + struct net_device *ndev = platform_get_drvdata(pdev); >>> + struct sun8i_emac_priv *priv = netdev_priv(ndev); >>> + >>> + phy_start(ndev->phydev); >>> + >>> + sun8i_emac_start_tx(ndev); >>> + sun8i_emac_start_rx(ndev); >>> + >>> + if (netif_running(ndev)) >>> + netif_device_attach(ndev); >>> + >>> + netif_start_queue(ndev); >>> + >>> + napi_enable(&priv->napi); >>> + >>> + return 0; >>> +} >> >> The main idea behind the runtime PM hooks is that they bring the >> device to a working state and shuts it down when it's not needed >> anymore. >> > > I expect that the first part (all pm_runtime_xxx) of the patch bring that. > When the interface is not opened: > cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status > suspended If your interface is not open, it should be in a low power state, only when it gets open (which means it is used) should you make it functional, that's pretty much the same thing as the runtime PM reference count usage here. I don't see a lot of value for using runtime_pm_* hooks here except calling into the existing suspend/resume functions that you have defined already, but then again, the code should be modular enough already in the driver. Runtime PM for network devices cannot be used as efficiently as you would with any kind of host-initiated bus/controller because your device needs to be able to receive packets without the host's ability to wake up the device to receive packets, so, with the exception of MDIO (which is host initiated), everything else besides except packet transmission (then again, I would not want to wait N ms to bring the interface in a state where it can now transmit packets, that's terrible for latency) is pretty much impossible to fully suspend due to its asynchronous nature. -- Florian ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support @ 2016-09-17 16:50 ` Florian Fainelli 0 siblings, 0 replies; 71+ messages in thread From: Florian Fainelli @ 2016-09-17 16:50 UTC (permalink / raw) To: LABBE Corentin, Maxime Ripard Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, davem-fT/PcQaiUtIeIZ0/mPfg9Q, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On 09/14/2016 07:03 AM, LABBE Corentin wrote: > On Mon, Sep 12, 2016 at 10:44:51PM +0200, Maxime Ripard wrote: >>> +static int __maybe_unused sun8i_emac_resume(struct platform_device *pdev) >>> +{ >>> + struct net_device *ndev = platform_get_drvdata(pdev); >>> + struct sun8i_emac_priv *priv = netdev_priv(ndev); >>> + >>> + phy_start(ndev->phydev); >>> + >>> + sun8i_emac_start_tx(ndev); >>> + sun8i_emac_start_rx(ndev); >>> + >>> + if (netif_running(ndev)) >>> + netif_device_attach(ndev); >>> + >>> + netif_start_queue(ndev); >>> + >>> + napi_enable(&priv->napi); >>> + >>> + return 0; >>> +} >> >> The main idea behind the runtime PM hooks is that they bring the >> device to a working state and shuts it down when it's not needed >> anymore. >> > > I expect that the first part (all pm_runtime_xxx) of the patch bring that. > When the interface is not opened: > cat /sys/devices/platform/soc/1c30000.ethernet/power/runtime_status > suspended If your interface is not open, it should be in a low power state, only when it gets open (which means it is used) should you make it functional, that's pretty much the same thing as the runtime PM reference count usage here. I don't see a lot of value for using runtime_pm_* hooks here except calling into the existing suspend/resume functions that you have defined already, but then again, the code should be modular enough already in the driver. Runtime PM for network devices cannot be used as efficiently as you would with any kind of host-initiated bus/controller because your device needs to be able to receive packets without the host's ability to wake up the device to receive packets, so, with the exception of MDIO (which is host initiated), everything else besides except packet transmission (then again, I would not want to wait N ms to bring the interface in a state where it can now transmit packets, that's terrible for latency) is pretty much impossible to fully suspend due to its asynchronous nature. -- Florian -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver @ 2016-09-10 3:58 ` David Miller 0 siblings, 0 replies; 71+ messages in thread From: David Miller @ 2016-09-10 3:58 UTC (permalink / raw) To: clabbe.montjoie Cc: robh+dt, mark.rutland, maxime.ripard, wens, linux, netdev, devicetree, linux-arm-kernel, linux-kernel From: Corentin Labbe <clabbe.montjoie@gmail.com> Date: Fri, 9 Sep 2016 14:45:08 +0200 > This patch series add the driver for sun8i-emac which handle the > Ethernet MAC present on Allwinner H3/A83T/A64 SoCs. Please don't post a patch series with some subset of the series marked as "RFC". I will just simply toss the entire series when you do this. Thank you. ^ permalink raw reply [flat|nested] 71+ messages in thread
* [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver @ 2016-09-10 3:58 ` David Miller 0 siblings, 0 replies; 71+ messages in thread From: David Miller @ 2016-09-10 3:58 UTC (permalink / raw) To: linux-arm-kernel From: Corentin Labbe <clabbe.montjoie@gmail.com> Date: Fri, 9 Sep 2016 14:45:08 +0200 > This patch series add the driver for sun8i-emac which handle the > Ethernet MAC present on Allwinner H3/A83T/A64 SoCs. Please don't post a patch series with some subset of the series marked as "RFC". I will just simply toss the entire series when you do this. Thank you. ^ permalink raw reply [flat|nested] 71+ messages in thread
* Re: [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver @ 2016-09-10 3:58 ` David Miller 0 siblings, 0 replies; 71+ messages in thread From: David Miller @ 2016-09-10 3:58 UTC (permalink / raw) To: clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8, wens-jdAy2FN1RRM, linux-I+IVW8TIWO2tmTQ+vhA3Yw, netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA From: Corentin Labbe <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> Date: Fri, 9 Sep 2016 14:45:08 +0200 > This patch series add the driver for sun8i-emac which handle the > Ethernet MAC present on Allwinner H3/A83T/A64 SoCs. Please don't post a patch series with some subset of the series marked as "RFC". I will just simply toss the entire series when you do this. Thank you. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 71+ messages in thread
end of thread, other threads:[~2016-09-17 16:50 UTC | newest] Thread overview: 71+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2016-09-09 12:45 [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 12:45 ` [PATCH v3 1/9] " Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 14:15 ` Andrew Lunn 2016-09-09 14:15 ` Andrew Lunn 2016-09-09 14:15 ` Andrew Lunn 2016-09-13 13:33 ` LABBE Corentin 2016-09-13 13:33 ` LABBE Corentin 2016-09-13 13:33 ` LABBE Corentin 2016-09-09 12:45 ` [PATCH v3 2/9] MAINTAINERS: Add myself as maintainer of sun8i-emac Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 12:45 ` [PATCH v3 3/9] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 14:04 ` Andrew Lunn 2016-09-09 14:04 ` Andrew Lunn 2016-09-09 14:04 ` Andrew Lunn 2016-09-12 15:01 ` LABBE Corentin 2016-09-12 15:01 ` LABBE Corentin 2016-09-12 15:15 ` Andrew Lunn 2016-09-12 15:15 ` Andrew Lunn 2016-09-09 14:17 ` Andrew Lunn 2016-09-09 14:17 ` Andrew Lunn 2016-09-13 13:34 ` LABBE Corentin 2016-09-13 13:34 ` LABBE Corentin 2016-09-13 14:12 ` Andrew Lunn 2016-09-13 14:12 ` Andrew Lunn 2016-09-09 12:45 ` [PATCH v3 4/9] ARM: dts: sun8i-h3: Add dt node for the syscon control module Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-12 7:28 ` Maxime Ripard 2016-09-12 7:28 ` Maxime Ripard 2016-09-13 13:38 ` LABBE Corentin 2016-09-13 13:38 ` LABBE Corentin 2016-09-13 13:38 ` LABBE Corentin 2016-09-09 12:45 ` [PATCH v3 5/9] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-12 7:29 ` Maxime Ripard 2016-09-12 7:29 ` Maxime Ripard 2016-09-12 7:29 ` Maxime Ripard 2016-09-14 8:54 ` LABBE Corentin 2016-09-14 8:54 ` LABBE Corentin 2016-09-09 12:45 ` [PATCH v3 6/9] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI PC Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 12:45 ` [PATCH v3 7/9] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI One Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-09 12:45 ` [PATCH v3 8/9] ARM: sunxi: Enable sun8i-emac driver on sunxi_defconfig Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-12 7:30 ` Maxime Ripard 2016-09-12 7:30 ` Maxime Ripard 2016-09-12 7:30 ` Maxime Ripard 2016-09-13 13:42 ` LABBE Corentin 2016-09-13 13:42 ` LABBE Corentin 2016-09-13 13:42 ` LABBE Corentin 2016-09-09 12:45 ` [RFC PATCH 9/9] ethernet: sun8i-emac: add pm_runtime support Corentin Labbe 2016-09-09 12:45 ` Corentin Labbe 2016-09-12 20:44 ` Maxime Ripard 2016-09-12 20:44 ` Maxime Ripard 2016-09-14 14:03 ` LABBE Corentin 2016-09-14 14:03 ` LABBE Corentin 2016-09-14 14:03 ` LABBE Corentin 2016-09-17 13:40 ` Maxime Ripard 2016-09-17 13:40 ` Maxime Ripard 2016-09-17 13:40 ` Maxime Ripard 2016-09-17 16:50 ` Florian Fainelli 2016-09-17 16:50 ` Florian Fainelli 2016-09-17 16:50 ` Florian Fainelli 2016-09-10 3:58 ` [PATCH v3 0/9] net-next: ethernet: add sun8i-emac driver David Miller 2016-09-10 3:58 ` David Miller 2016-09-10 3:58 ` David Miller
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.