From: Russell King - ARM Linux admin <linux@armlinux.org.uk> To: stefanc@marvell.com Cc: netdev@vger.kernel.org, thomas.petazzoni@bootlin.com, davem@davemloft.net, nadavh@marvell.com, ymarkman@marvell.com, linux-kernel@vger.kernel.org, kuba@kernel.org, mw@semihalf.com, andrew@lunn.ch, atenart@kernel.org, devicetree@vger.kernel.org, robh+dt@kernel.org, sebastian.hesselbarth@gmail.com, gregory.clement@bootlin.com, linux-arm-kernel@lists.infradead.org Subject: Re: [PATCH v13 net-next 07/15] net: mvpp2: add FCA periodic timer configurations Date: Thu, 11 Feb 2021 12:47:19 +0000 [thread overview] Message-ID: <20210211124719.GE1463@shell.armlinux.org.uk> (raw) In-Reply-To: <1613040542-16500-8-git-send-email-stefanc@marvell.com> On Thu, Feb 11, 2021 at 12:48:54PM +0200, stefanc@marvell.com wrote: > @@ -751,6 +760,10 @@ > #define MVPP2_TX_FIFO_THRESHOLD(kb) \ > ((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN) > > +/* MSS Flow control */ > +#define FC_QUANTA 0xFFFF > +#define FC_CLK_DIVIDER 100 You later change the number of tabs for these definitions in a later patch. Would it be better to start having the correct number of tabs? > + > /* RX buffer constants */ > #define MVPP2_SKB_SHINFO_SIZE \ > SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) > diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c > index 5730900..761f745 100644 > --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c > +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c > @@ -1280,6 +1280,49 @@ static void mvpp22_gop_init_10gkr(struct mvpp2_port *port) > writel(val, mpcs + MVPP22_MPCS_CLK_RESET); > } > > +static void mvpp22_gop_fca_enable_periodic(struct mvpp2_port *port, bool en) > +{ > + struct mvpp2 *priv = port->priv; > + void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id); > + u32 val; net likes to have reverse christmas tree variables. I think you should clean this up. However... > + > + val = readl(fca + MVPP22_FCA_CONTROL_REG); > + val &= ~MVPP22_FCA_ENABLE_PERIODIC; > + if (en) > + val |= MVPP22_FCA_ENABLE_PERIODIC; > + writel(val, fca + MVPP22_FCA_CONTROL_REG); if (en) val = MVPP22_FCA_ENABLE_PERIODIC; else val = 0; mvpp2_modify(priv->iface_base + MVPP22_FCA_BASE(port->gop_id) + MVPP22_FCA_CONTROL_REG, MVPP22_FCA_ENABLE_PERIODIC, val); avoids the need for "fca". > +} > + > +static void mvpp22_gop_fca_set_timer(struct mvpp2_port *port, u32 timer) > +{ > + struct mvpp2 *priv = port->priv; > + void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id); > + u32 lsb, msb; Same reverse christmas tree issue here. -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
WARNING: multiple messages have this Message-ID (diff)
From: Russell King - ARM Linux admin <linux@armlinux.org.uk> To: stefanc@marvell.com Cc: andrew@lunn.ch, ymarkman@marvell.com, devicetree@vger.kernel.org, netdev@vger.kernel.org, atenart@kernel.org, linux-kernel@vger.kernel.org, nadavh@marvell.com, robh+dt@kernel.org, linux-arm-kernel@lists.infradead.org, thomas.petazzoni@bootlin.com, kuba@kernel.org, mw@semihalf.com, davem@davemloft.net, gregory.clement@bootlin.com, sebastian.hesselbarth@gmail.com Subject: Re: [PATCH v13 net-next 07/15] net: mvpp2: add FCA periodic timer configurations Date: Thu, 11 Feb 2021 12:47:19 +0000 [thread overview] Message-ID: <20210211124719.GE1463@shell.armlinux.org.uk> (raw) In-Reply-To: <1613040542-16500-8-git-send-email-stefanc@marvell.com> On Thu, Feb 11, 2021 at 12:48:54PM +0200, stefanc@marvell.com wrote: > @@ -751,6 +760,10 @@ > #define MVPP2_TX_FIFO_THRESHOLD(kb) \ > ((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN) > > +/* MSS Flow control */ > +#define FC_QUANTA 0xFFFF > +#define FC_CLK_DIVIDER 100 You later change the number of tabs for these definitions in a later patch. Would it be better to start having the correct number of tabs? > + > /* RX buffer constants */ > #define MVPP2_SKB_SHINFO_SIZE \ > SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) > diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c > index 5730900..761f745 100644 > --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c > +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c > @@ -1280,6 +1280,49 @@ static void mvpp22_gop_init_10gkr(struct mvpp2_port *port) > writel(val, mpcs + MVPP22_MPCS_CLK_RESET); > } > > +static void mvpp22_gop_fca_enable_periodic(struct mvpp2_port *port, bool en) > +{ > + struct mvpp2 *priv = port->priv; > + void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id); > + u32 val; net likes to have reverse christmas tree variables. I think you should clean this up. However... > + > + val = readl(fca + MVPP22_FCA_CONTROL_REG); > + val &= ~MVPP22_FCA_ENABLE_PERIODIC; > + if (en) > + val |= MVPP22_FCA_ENABLE_PERIODIC; > + writel(val, fca + MVPP22_FCA_CONTROL_REG); if (en) val = MVPP22_FCA_ENABLE_PERIODIC; else val = 0; mvpp2_modify(priv->iface_base + MVPP22_FCA_BASE(port->gop_id) + MVPP22_FCA_CONTROL_REG, MVPP22_FCA_ENABLE_PERIODIC, val); avoids the need for "fca". > +} > + > +static void mvpp22_gop_fca_set_timer(struct mvpp2_port *port, u32 timer) > +{ > + struct mvpp2 *priv = port->priv; > + void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id); > + u32 lsb, msb; Same reverse christmas tree issue here. -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last! _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-02-11 13:10 UTC|newest] Thread overview: 72+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-02-11 10:48 [PATCH v13 net-next 00/15] net: mvpp2: Add TX Flow Control support stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 10:48 ` [PATCH v13 net-next 01/15] doc: marvell: add CM3 address space and PPv2.3 description stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 11:02 ` Russell King - ARM Linux admin 2021-02-11 11:02 ` Russell King - ARM Linux admin 2021-02-11 10:48 ` [PATCH v13 net-next 02/15] dts: marvell: add CM3 SRAM memory to cp11x ethernet device tree stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 10:48 ` [PATCH v13 net-next 03/15] net: mvpp2: add CM3 SRAM memory map stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 11:05 ` Russell King - ARM Linux admin 2021-02-11 11:05 ` Russell King - ARM Linux admin 2021-02-11 10:48 ` [PATCH v13 net-next 04/15] net: mvpp2: always compare hw-version vs MVPP21 stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 11:08 ` Russell King - ARM Linux admin 2021-02-11 11:08 ` Russell King - ARM Linux admin 2021-02-11 11:10 ` [EXT] " Stefan Chulski 2021-02-11 11:10 ` Stefan Chulski 2021-02-11 10:48 ` [PATCH v13 net-next 05/15] net: mvpp2: add PPv23 version definition stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 11:42 ` Russell King - ARM Linux admin 2021-02-11 11:42 ` Russell King - ARM Linux admin 2021-02-11 11:49 ` [EXT] " Stefan Chulski 2021-02-11 11:49 ` Stefan Chulski 2021-02-11 19:26 ` Marcin Wojtas 2021-02-11 19:26 ` Marcin Wojtas 2021-02-11 10:48 ` [PATCH v13 net-next 06/15] net: mvpp2: increase BM pool and RXQ size stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 11:09 ` Russell King - ARM Linux admin 2021-02-11 11:09 ` Russell King - ARM Linux admin 2021-02-11 10:48 ` [PATCH v13 net-next 07/15] net: mvpp2: add FCA periodic timer configurations stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 12:47 ` Russell King - ARM Linux admin [this message] 2021-02-11 12:47 ` Russell King - ARM Linux admin 2021-02-11 10:48 ` [PATCH v13 net-next 08/15] net: mvpp2: add FCA RXQ non occupied descriptor threshold stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 12:50 ` Russell King - ARM Linux admin 2021-02-11 12:50 ` Russell King - ARM Linux admin 2021-02-11 13:02 ` [EXT] " Stefan Chulski 2021-02-11 13:02 ` Stefan Chulski 2021-02-11 13:29 ` Russell King - ARM Linux admin 2021-02-11 13:29 ` Russell King - ARM Linux admin 2021-02-11 13:22 ` Stefan Chulski 2021-02-11 13:22 ` Stefan Chulski 2021-02-11 13:31 ` Russell King - ARM Linux admin 2021-02-11 13:31 ` Russell King - ARM Linux admin 2021-02-11 10:48 ` [PATCH v13 net-next 09/15] net: mvpp2: enable global flow control stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 12:52 ` Russell King - ARM Linux admin 2021-02-11 12:52 ` Russell King - ARM Linux admin 2021-02-11 10:48 ` [PATCH v13 net-next 10/15] net: mvpp2: add RXQ flow control configurations stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 10:48 ` [PATCH v13 net-next 11/15] net: mvpp2: add ethtool flow control configuration support stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 10:48 ` [PATCH v13 net-next 12/15] net: mvpp2: add BM protection underrun feature support stefanc 2021-02-11 10:48 ` stefanc 2021-02-11 10:49 ` [PATCH v13 net-next 13/15] net: mvpp2: add PPv23 RX FIFO flow control stefanc 2021-02-11 10:49 ` stefanc 2021-02-11 12:56 ` Russell King - ARM Linux admin 2021-02-11 12:56 ` Russell King - ARM Linux admin 2021-02-11 13:06 ` [EXT] " Stefan Chulski 2021-02-11 13:06 ` Stefan Chulski 2021-02-11 10:49 ` [PATCH v13 net-next 14/15] net: mvpp2: set 802.3x GoP Flow Control mode stefanc 2021-02-11 10:49 ` stefanc 2021-02-11 12:57 ` Russell King - ARM Linux admin 2021-02-11 12:57 ` Russell King - ARM Linux admin 2021-02-11 10:49 ` [PATCH v13 net-next 15/15] net: mvpp2: add TX FC firmware check stefanc 2021-02-11 10:49 ` stefanc 2021-02-11 23:00 ` [PATCH v13 net-next 00/15] net: mvpp2: Add TX Flow Control support patchwork-bot+netdevbpf 2021-02-11 23:00 ` patchwork-bot+netdevbpf 2021-02-12 8:54 ` [EXT] " Stefan Chulski 2021-02-12 8:54 ` Stefan Chulski
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210211124719.GE1463@shell.armlinux.org.uk \ --to=linux@armlinux.org.uk \ --cc=andrew@lunn.ch \ --cc=atenart@kernel.org \ --cc=davem@davemloft.net \ --cc=devicetree@vger.kernel.org \ --cc=gregory.clement@bootlin.com \ --cc=kuba@kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=mw@semihalf.com \ --cc=nadavh@marvell.com \ --cc=netdev@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=sebastian.hesselbarth@gmail.com \ --cc=stefanc@marvell.com \ --cc=thomas.petazzoni@bootlin.com \ --cc=ymarkman@marvell.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.