[PATCH 0/8] Devicetree fixes and additions for Kontron SL/BL i.MX8MM boards

[PATCH 0/8] Devicetree fixes and additions for Kontron SL/BL i.MX8MM boards

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This is a set of enhancements and fixes for the devicetrees of the Kontron
SL/BL i.MX8MM SoMs and boards.

Frieder Schrempf (8):
  arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on
    SD card
  arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are
    correct
  arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV
  arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators
  arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency
  arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY
  arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY
  arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

 .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 41 ++++++++++++++++---
 .../freescale/imx8mm-kontron-n801x-som.dtsi   | 13 ++++--
 2 files changed, 44 insertions(+), 10 deletions(-)

-- 
2.33.0

[PATCH 0/8] Devicetree fixes and additions for Kontron SL/BL i.MX8MM boards

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This is a set of enhancements and fixes for the devicetrees of the Kontron
SL/BL i.MX8MM SoMs and boards.

Frieder Schrempf (8):
  arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on
    SD card
  arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are
    correct
  arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV
  arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators
  arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency
  arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY
  arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY
  arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

 .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 41 ++++++++++++++++---
 .../freescale/imx8mm-kontron-n801x-som.dtsi   | 13 ++++--
 2 files changed, 44 insertions(+), 10 deletions(-)

-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/8] arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

In order to use ultra high speed modes (UHS) on the SD card slot, we
add matching pinctrls and fix the voltage switching for LDO5 of the
PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 28 ++++++++++++++++++-
 .../freescale/imx8mm-kontron-n801x-som.dtsi   |  2 ++
 2 files changed, 29 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index d17abb515835..62ba3bd08a0c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -189,8 +189,10 @@ usbnet: usbether@1 {
 };
 
 &usdhc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
 	vqmmc-supply = <&reg_nvcc_sd>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
@@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
 		>;
 	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index d0456daefda8..03b3516abd64 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -86,6 +86,7 @@ pca9450: pmic@25 {
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 
-- 
2.33.0

[PATCH 1/8] arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

In order to use ultra high speed modes (UHS) on the SD card slot, we
add matching pinctrls and fix the voltage switching for LDO5 of the
PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 28 ++++++++++++++++++-
 .../freescale/imx8mm-kontron-n801x-som.dtsi   |  2 ++
 2 files changed, 29 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index d17abb515835..62ba3bd08a0c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -189,8 +189,10 @@ usbnet: usbether@1 {
 };
 
 &usdhc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
 	vqmmc-supply = <&reg_nvcc_sd>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
@@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
 		>;
 	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index d0456daefda8..03b3516abd64 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -86,6 +86,7 @@ pca9450: pmic@25 {
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/8] arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:24PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> In order to use ultra high speed modes (UHS) on the SD card slot, we
> add matching pinctrls and fix the voltage switching for LDO5 of the
> PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 28 ++++++++++++++++++-
>  .../freescale/imx8mm-kontron-n801x-som.dtsi   |  2 ++
>  2 files changed, 29 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index d17abb515835..62ba3bd08a0c 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -189,8 +189,10 @@ usbnet: usbether@1 {
>  };
>  
>  &usdhc2 {
> -	pinctrl-names = "default";
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
>  	pinctrl-0 = <&pinctrl_usdhc2>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
>  	vmmc-supply = <&reg_vdd_3v3>;
>  	vqmmc-supply = <&reg_nvcc_sd>;
>  	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> @@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
>  			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>  		>;
>  	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {

Did you run dtbs_check on it?

Shawn

> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
> +		>;
> +	};
>  };
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index d0456daefda8..03b3516abd64 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -86,6 +86,7 @@ pca9450: pmic@25 {
>  		pinctrl-0 = <&pinctrl_pmic>;
>  		interrupt-parent = <&gpio1>;
>  		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
>  
>  		regulators {
>  			reg_vdd_soc: BUCK1 {
> @@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
>  	pinctrl_pmic: pmicgrp {
>  		fsl,pins = <
>  			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
> +			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
>  		>;
>  	};
>  
> -- 
> 2.33.0
> 

Re: [PATCH 1/8] arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:24PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> In order to use ultra high speed modes (UHS) on the SD card slot, we
> add matching pinctrls and fix the voltage switching for LDO5 of the
> PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 28 ++++++++++++++++++-
>  .../freescale/imx8mm-kontron-n801x-som.dtsi   |  2 ++
>  2 files changed, 29 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index d17abb515835..62ba3bd08a0c 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -189,8 +189,10 @@ usbnet: usbether@1 {
>  };
>  
>  &usdhc2 {
> -	pinctrl-names = "default";
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
>  	pinctrl-0 = <&pinctrl_usdhc2>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
>  	vmmc-supply = <&reg_vdd_3v3>;
>  	vqmmc-supply = <&reg_nvcc_sd>;
>  	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> @@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
>  			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>  		>;
>  	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {

Did you run dtbs_check on it?

Shawn

> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
> +		>;
> +	};
>  };
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index d0456daefda8..03b3516abd64 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -86,6 +86,7 @@ pca9450: pmic@25 {
>  		pinctrl-0 = <&pinctrl_pmic>;
>  		interrupt-parent = <&gpio1>;
>  		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
>  
>  		regulators {
>  			reg_vdd_soc: BUCK1 {
> @@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
>  	pinctrl_pmic: pmicgrp {
>  		fsl,pins = <
>  			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
> +			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
>  		>;
>  	};
>  
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/8] arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card

[Frieder Schrempf]

On 05.10.21 08:45, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:24PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> In order to use ultra high speed modes (UHS) on the SD card slot, we
>> add matching pinctrls and fix the voltage switching for LDO5 of the
>> PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 28 ++++++++++++++++++-
>>  .../freescale/imx8mm-kontron-n801x-som.dtsi   |  2 ++
>>  2 files changed, 29 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> index d17abb515835..62ba3bd08a0c 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> @@ -189,8 +189,10 @@ usbnet: usbether@1 {
>>  };
>>  
>>  &usdhc2 {
>> -	pinctrl-names = "default";
>> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
>>  	pinctrl-0 = <&pinctrl_usdhc2>;
>> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
>> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
>>  	vmmc-supply = <&reg_vdd_3v3>;
>>  	vqmmc-supply = <&reg_nvcc_sd>;
>>  	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
>> @@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
>>  			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>>  		>;
>>  	};
>> +
>> +	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> 
> Did you run dtbs_check on it?

Thanks for the reminder. I ran the check now and will fix up the node
names in v2.

> 
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
>> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
>> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>> +		>;
>> +	};
>> +
>> +	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
>> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
>> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>> +		>;
>> +	};
>>  };
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> index d0456daefda8..03b3516abd64 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> @@ -86,6 +86,7 @@ pca9450: pmic@25 {
>>  		pinctrl-0 = <&pinctrl_pmic>;
>>  		interrupt-parent = <&gpio1>;
>>  		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> +		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
>>  
>>  		regulators {
>>  			reg_vdd_soc: BUCK1 {
>> @@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
>>  	pinctrl_pmic: pmicgrp {
>>  		fsl,pins = <
>>  			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
>> +			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
>>  		>;
>>  	};
>>  
>> -- 
>> 2.33.0
>>

Re: [PATCH 1/8] arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card

[Frieder Schrempf]

On 05.10.21 08:45, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:24PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> In order to use ultra high speed modes (UHS) on the SD card slot, we
>> add matching pinctrls and fix the voltage switching for LDO5 of the
>> PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 28 ++++++++++++++++++-
>>  .../freescale/imx8mm-kontron-n801x-som.dtsi   |  2 ++
>>  2 files changed, 29 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> index d17abb515835..62ba3bd08a0c 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> @@ -189,8 +189,10 @@ usbnet: usbether@1 {
>>  };
>>  
>>  &usdhc2 {
>> -	pinctrl-names = "default";
>> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
>>  	pinctrl-0 = <&pinctrl_usdhc2>;
>> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
>> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
>>  	vmmc-supply = <&reg_vdd_3v3>;
>>  	vqmmc-supply = <&reg_nvcc_sd>;
>>  	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
>> @@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
>>  			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>>  		>;
>>  	};
>> +
>> +	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> 
> Did you run dtbs_check on it?

Thanks for the reminder. I ran the check now and will fix up the node
names in v2.

> 
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
>> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
>> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
>> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>> +		>;
>> +	};
>> +
>> +	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
>> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
>> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
>> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
>> +		>;
>> +	};
>>  };
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> index d0456daefda8..03b3516abd64 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> @@ -86,6 +86,7 @@ pca9450: pmic@25 {
>>  		pinctrl-0 = <&pinctrl_pmic>;
>>  		interrupt-parent = <&gpio1>;
>>  		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> +		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
>>  
>>  		regulators {
>>  			reg_vdd_soc: BUCK1 {
>> @@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
>>  	pinctrl_pmic: pmicgrp {
>>  		fsl,pins = <
>>  			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
>> +			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
>>  		>;
>>  	};
>>  
>> -- 
>> 2.33.0
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
should be 950 mV for DDR clock frequencies of 1.5 GHz.

This information is taken from the datasheet and the uboot-imx code.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 03b3516abd64..b12fb7ce6686 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -92,10 +92,12 @@ regulators {
 			reg_vdd_soc: BUCK1 {
 				regulator-name = "buck1";
 				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <900000>;
+				regulator-max-microvolt = <850000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
 			};
 
 			reg_vdd_arm: BUCK2 {
@@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
 			reg_vdd_dram: BUCK3 {
 				regulator-name = "buck3";
 				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <900000>;
+				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
-- 
2.33.0

[PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
should be 950 mV for DDR clock frequencies of 1.5 GHz.

This information is taken from the datasheet and the uboot-imx code.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 03b3516abd64..b12fb7ce6686 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -92,10 +92,12 @@ regulators {
 			reg_vdd_soc: BUCK1 {
 				regulator-name = "buck1";
 				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <900000>;
+				regulator-max-microvolt = <850000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
 			};
 
 			reg_vdd_arm: BUCK2 {
@@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
 			reg_vdd_dram: BUCK3 {
 				regulator-name = "buck3";
 				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <900000>;
+				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

On 30.09.21 17:56, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> should be 950 mV for DDR clock frequencies of 1.5 GHz.
> 
> This information is taken from the datasheet and the uboot-imx code.
> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

This should also have:

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and
baseboards")
Cc: stable@vger.kernel.org

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 03b3516abd64..b12fb7ce6686 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -92,10 +92,12 @@ regulators {
>  			reg_vdd_soc: BUCK1 {
>  				regulator-name = "buck1";
>  				regulator-min-microvolt = <800000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <850000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  				regulator-ramp-delay = <3125>;
> +				nxp,dvs-run-voltage = <850000>;
> +				nxp,dvs-standby-voltage = <800000>;
>  			};
>  
>  			reg_vdd_arm: BUCK2 {
> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
>  			reg_vdd_dram: BUCK3 {
>  				regulator-name = "buck3";
>  				regulator-min-microvolt = <850000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <950000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  			};
> 

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

On 30.09.21 17:56, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> should be 950 mV for DDR clock frequencies of 1.5 GHz.
> 
> This information is taken from the datasheet and the uboot-imx code.
> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

This should also have:

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and
baseboards")
Cc: stable@vger.kernel.org

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 03b3516abd64..b12fb7ce6686 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -92,10 +92,12 @@ regulators {
>  			reg_vdd_soc: BUCK1 {
>  				regulator-name = "buck1";
>  				regulator-min-microvolt = <800000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <850000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  				regulator-ramp-delay = <3125>;
> +				nxp,dvs-run-voltage = <850000>;
> +				nxp,dvs-standby-voltage = <800000>;
>  			};
>  
>  			reg_vdd_arm: BUCK2 {
> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
>  			reg_vdd_dram: BUCK3 {
>  				regulator-name = "buck3";
>  				regulator-min-microvolt = <850000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <950000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  			};
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Shawn Guo]

On Thu, Sep 30, 2021 at 06:02:01PM +0200, Frieder Schrempf wrote:
> On 30.09.21 17:56, Frieder Schrempf wrote:
> > From: Frieder Schrempf <frieder.schrempf@kontron.de>
> > 
> > VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> > should be 950 mV for DDR clock frequencies of 1.5 GHz.
> > 
> > This information is taken from the datasheet and the uboot-imx code.
> > 
> > Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> This should also have:
> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and
> baseboards")

$ git log 21c4f45b335f
fatal: ambiguous argument '21c4f45b335f': unknown revision or path not in the working tree.
Use '--' to separate paths from revisions, like this:
'git <command> [<revision>...] -- [<file>...]'

Shawn

> Cc: stable@vger.kernel.org
> 
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
> >  1 file changed, 4 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> > index 03b3516abd64..b12fb7ce6686 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> > @@ -92,10 +92,12 @@ regulators {
> >  			reg_vdd_soc: BUCK1 {
> >  				regulator-name = "buck1";
> >  				regulator-min-microvolt = <800000>;
> > -				regulator-max-microvolt = <900000>;
> > +				regulator-max-microvolt = <850000>;
> >  				regulator-boot-on;
> >  				regulator-always-on;
> >  				regulator-ramp-delay = <3125>;
> > +				nxp,dvs-run-voltage = <850000>;
> > +				nxp,dvs-standby-voltage = <800000>;
> >  			};
> >  
> >  			reg_vdd_arm: BUCK2 {
> > @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
> >  			reg_vdd_dram: BUCK3 {
> >  				regulator-name = "buck3";
> >  				regulator-min-microvolt = <850000>;
> > -				regulator-max-microvolt = <900000>;
> > +				regulator-max-microvolt = <950000>;
> >  				regulator-boot-on;
> >  				regulator-always-on;
> >  			};
> > 

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Shawn Guo]

On Thu, Sep 30, 2021 at 06:02:01PM +0200, Frieder Schrempf wrote:
> On 30.09.21 17:56, Frieder Schrempf wrote:
> > From: Frieder Schrempf <frieder.schrempf@kontron.de>
> > 
> > VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> > should be 950 mV for DDR clock frequencies of 1.5 GHz.
> > 
> > This information is taken from the datasheet and the uboot-imx code.
> > 
> > Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> This should also have:
> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and
> baseboards")

$ git log 21c4f45b335f
fatal: ambiguous argument '21c4f45b335f': unknown revision or path not in the working tree.
Use '--' to separate paths from revisions, like this:
'git <command> [<revision>...] -- [<file>...]'

Shawn

> Cc: stable@vger.kernel.org
> 
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
> >  1 file changed, 4 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> > index 03b3516abd64..b12fb7ce6686 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> > @@ -92,10 +92,12 @@ regulators {
> >  			reg_vdd_soc: BUCK1 {
> >  				regulator-name = "buck1";
> >  				regulator-min-microvolt = <800000>;
> > -				regulator-max-microvolt = <900000>;
> > +				regulator-max-microvolt = <850000>;
> >  				regulator-boot-on;
> >  				regulator-always-on;
> >  				regulator-ramp-delay = <3125>;
> > +				nxp,dvs-run-voltage = <850000>;
> > +				nxp,dvs-standby-voltage = <800000>;
> >  			};
> >  
> >  			reg_vdd_arm: BUCK2 {
> > @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
> >  			reg_vdd_dram: BUCK3 {
> >  				regulator-name = "buck3";
> >  				regulator-min-microvolt = <850000>;
> > -				regulator-max-microvolt = <900000>;
> > +				regulator-max-microvolt = <950000>;
> >  				regulator-boot-on;
> >  				regulator-always-on;
> >  			};
> > 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:25PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> should be 950 mV for DDR clock frequencies of 1.5 GHz.
> 
> This information is taken from the datasheet and the uboot-imx code.

I'm wondering where the existing settings were coming from?

Shawn

> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 03b3516abd64..b12fb7ce6686 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -92,10 +92,12 @@ regulators {
>  			reg_vdd_soc: BUCK1 {
>  				regulator-name = "buck1";
>  				regulator-min-microvolt = <800000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <850000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  				regulator-ramp-delay = <3125>;
> +				nxp,dvs-run-voltage = <850000>;
> +				nxp,dvs-standby-voltage = <800000>;
>  			};
>  
>  			reg_vdd_arm: BUCK2 {
> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
>  			reg_vdd_dram: BUCK3 {
>  				regulator-name = "buck3";
>  				regulator-min-microvolt = <850000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <950000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  			};
> -- 
> 2.33.0
> 

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:25PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> should be 950 mV for DDR clock frequencies of 1.5 GHz.
> 
> This information is taken from the datasheet and the uboot-imx code.

I'm wondering where the existing settings were coming from?

Shawn

> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 03b3516abd64..b12fb7ce6686 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -92,10 +92,12 @@ regulators {
>  			reg_vdd_soc: BUCK1 {
>  				regulator-name = "buck1";
>  				regulator-min-microvolt = <800000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <850000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  				regulator-ramp-delay = <3125>;
> +				nxp,dvs-run-voltage = <850000>;
> +				nxp,dvs-standby-voltage = <800000>;
>  			};
>  
>  			reg_vdd_arm: BUCK2 {
> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
>  			reg_vdd_dram: BUCK3 {
>  				regulator-name = "buck3";
>  				regulator-min-microvolt = <850000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-max-microvolt = <950000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  			};
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

On 05.10.21 08:53, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:25PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
>> should be 950 mV for DDR clock frequencies of 1.5 GHz.
>>
>> This information is taken from the datasheet and the uboot-imx code.
> 
> I'm wondering where the existing settings were coming from?

Good question, but I can't really retrace now how I actually determined
the values back then. Seems like I had failed to validate them properly.

> 
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
>>  1 file changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> index 03b3516abd64..b12fb7ce6686 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> @@ -92,10 +92,12 @@ regulators {
>>  			reg_vdd_soc: BUCK1 {
>>  				regulator-name = "buck1";
>>  				regulator-min-microvolt = <800000>;
>> -				regulator-max-microvolt = <900000>;
>> +				regulator-max-microvolt = <850000>;
>>  				regulator-boot-on;
>>  				regulator-always-on;
>>  				regulator-ramp-delay = <3125>;
>> +				nxp,dvs-run-voltage = <850000>;
>> +				nxp,dvs-standby-voltage = <800000>;
>>  			};
>>  
>>  			reg_vdd_arm: BUCK2 {
>> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
>>  			reg_vdd_dram: BUCK3 {
>>  				regulator-name = "buck3";
>>  				regulator-min-microvolt = <850000>;
>> -				regulator-max-microvolt = <900000>;
>> +				regulator-max-microvolt = <950000>;
>>  				regulator-boot-on;
>>  				regulator-always-on;
>>  			};
>> -- 
>> 2.33.0
>>

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

On 05.10.21 08:53, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:25PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
>> should be 950 mV for DDR clock frequencies of 1.5 GHz.
>>
>> This information is taken from the datasheet and the uboot-imx code.
> 
> I'm wondering where the existing settings were coming from?

Good question, but I can't really retrace now how I actually determined
the values back then. Seems like I had failed to validate them properly.

> 
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
>>  1 file changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> index 03b3516abd64..b12fb7ce6686 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> @@ -92,10 +92,12 @@ regulators {
>>  			reg_vdd_soc: BUCK1 {
>>  				regulator-name = "buck1";
>>  				regulator-min-microvolt = <800000>;
>> -				regulator-max-microvolt = <900000>;
>> +				regulator-max-microvolt = <850000>;
>>  				regulator-boot-on;
>>  				regulator-always-on;
>>  				regulator-ramp-delay = <3125>;
>> +				nxp,dvs-run-voltage = <850000>;
>> +				nxp,dvs-standby-voltage = <800000>;
>>  			};
>>  
>>  			reg_vdd_arm: BUCK2 {
>> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
>>  			reg_vdd_dram: BUCK3 {
>>  				regulator-name = "buck3";
>>  				regulator-min-microvolt = <850000>;
>> -				regulator-max-microvolt = <900000>;
>> +				regulator-max-microvolt = <950000>;
>>  				regulator-boot-on;
>>  				regulator-always-on;
>>  			};
>> -- 
>> 2.33.0
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Shawn Guo]

On Tue, Oct 05, 2021 at 03:10:14PM +0200, Frieder Schrempf wrote:
> On 05.10.21 08:53, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:25PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> >> should be 950 mV for DDR clock frequencies of 1.5 GHz.
> >>
> >> This information is taken from the datasheet and the uboot-imx code.
> > 
> > I'm wondering where the existing settings were coming from?
> 
> Good question, but I can't really retrace now how I actually determined
> the values back then. Seems like I had failed to validate them properly.

Please update commit log with these background info.

Shawn

> 
> > 
> >>
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
> >>  1 file changed, 4 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> index 03b3516abd64..b12fb7ce6686 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> @@ -92,10 +92,12 @@ regulators {
> >>  			reg_vdd_soc: BUCK1 {
> >>  				regulator-name = "buck1";
> >>  				regulator-min-microvolt = <800000>;
> >> -				regulator-max-microvolt = <900000>;
> >> +				regulator-max-microvolt = <850000>;
> >>  				regulator-boot-on;
> >>  				regulator-always-on;
> >>  				regulator-ramp-delay = <3125>;
> >> +				nxp,dvs-run-voltage = <850000>;
> >> +				nxp,dvs-standby-voltage = <800000>;
> >>  			};
> >>  
> >>  			reg_vdd_arm: BUCK2 {
> >> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
> >>  			reg_vdd_dram: BUCK3 {
> >>  				regulator-name = "buck3";
> >>  				regulator-min-microvolt = <850000>;
> >> -				regulator-max-microvolt = <900000>;
> >> +				regulator-max-microvolt = <950000>;
> >>  				regulator-boot-on;
> >>  				regulator-always-on;
> >>  			};
> >> -- 
> >> 2.33.0
> >>

Re: [PATCH 2/8] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Shawn Guo]

On Tue, Oct 05, 2021 at 03:10:14PM +0200, Frieder Schrempf wrote:
> On 05.10.21 08:53, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:25PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> VDD_SOC should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM
> >> should be 950 mV for DDR clock frequencies of 1.5 GHz.
> >>
> >> This information is taken from the datasheet and the uboot-imx code.
> > 
> > I'm wondering where the existing settings were coming from?
> 
> Good question, but I can't really retrace now how I actually determined
> the values back then. Seems like I had failed to validate them properly.

Please update commit log with these background info.

Shawn

> 
> > 
> >>
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
> >>  1 file changed, 4 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> index 03b3516abd64..b12fb7ce6686 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> @@ -92,10 +92,12 @@ regulators {
> >>  			reg_vdd_soc: BUCK1 {
> >>  				regulator-name = "buck1";
> >>  				regulator-min-microvolt = <800000>;
> >> -				regulator-max-microvolt = <900000>;
> >> +				regulator-max-microvolt = <850000>;
> >>  				regulator-boot-on;
> >>  				regulator-always-on;
> >>  				regulator-ramp-delay = <3125>;
> >> +				nxp,dvs-run-voltage = <850000>;
> >> +				nxp,dvs-standby-voltage = <800000>;
> >>  			};
> >>  
> >>  			reg_vdd_arm: BUCK2 {
> >> @@ -111,7 +113,7 @@ reg_vdd_arm: BUCK2 {
> >>  			reg_vdd_dram: BUCK3 {
> >>  				regulator-name = "buck3";
> >>  				regulator-min-microvolt = <850000>;
> >> -				regulator-max-microvolt = <900000>;
> >> +				regulator-max-microvolt = <950000>;
> >>  				regulator-boot-on;
> >>  				regulator-always-on;
> >>  			};
> >> -- 
> >> 2.33.0
> >>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

According to the datasheet VDD_SNVS should be 800 mV, so let's
make sure that the voltage won't be different.

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index b12fb7ce6686..213014f59b46 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
 
 			reg_vdd_snvs: LDO2 {
 				regulator-name = "ldo2";
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
-- 
2.33.0

[PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

According to the datasheet VDD_SNVS should be 800 mV, so let's
make sure that the voltage won't be different.

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index b12fb7ce6686..213014f59b46 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
 
 			reg_vdd_snvs: LDO2 {
 				regulator-name = "ldo2";
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:26PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> According to the datasheet VDD_SNVS should be 800 mV, so let's
> make sure that the voltage won't be different.

Could you share the datasheet?

Shawn

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index b12fb7ce6686..213014f59b46 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
>  
>  			reg_vdd_snvs: LDO2 {
>  				regulator-name = "ldo2";
> -				regulator-min-microvolt = <850000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  			};
> -- 
> 2.33.0
> 

Re: [PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:26PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> According to the datasheet VDD_SNVS should be 800 mV, so let's
> make sure that the voltage won't be different.

Could you share the datasheet?

Shawn

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index b12fb7ce6686..213014f59b46 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
>  
>  			reg_vdd_snvs: LDO2 {
>  				regulator-name = "ldo2";
> -				regulator-min-microvolt = <850000>;
> -				regulator-max-microvolt = <900000>;
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
>  				regulator-boot-on;
>  				regulator-always-on;
>  			};
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Frieder Schrempf]

On 05.10.21 08:56, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:26PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> According to the datasheet VDD_SNVS should be 800 mV, so let's
>> make sure that the voltage won't be different.
> 
> Could you share the datasheet?

Sure, it's here: https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf.
See table 10 for the operating voltages.

>>
>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
>>  1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> index b12fb7ce6686..213014f59b46 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> @@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
>>  
>>  			reg_vdd_snvs: LDO2 {
>>  				regulator-name = "ldo2";
>> -				regulator-min-microvolt = <850000>;
>> -				regulator-max-microvolt = <900000>;
>> +				regulator-min-microvolt = <800000>;
>> +				regulator-max-microvolt = <800000>;
>>  				regulator-boot-on;
>>  				regulator-always-on;
>>  			};
>> -- 
>> 2.33.0
>>

Re: [PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Frieder Schrempf]

On 05.10.21 08:56, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:26PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> According to the datasheet VDD_SNVS should be 800 mV, so let's
>> make sure that the voltage won't be different.
> 
> Could you share the datasheet?

Sure, it's here: https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf.
See table 10 for the operating voltages.

>>
>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
>>  1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> index b12fb7ce6686..213014f59b46 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>> @@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
>>  
>>  			reg_vdd_snvs: LDO2 {
>>  				regulator-name = "ldo2";
>> -				regulator-min-microvolt = <850000>;
>> -				regulator-max-microvolt = <900000>;
>> +				regulator-min-microvolt = <800000>;
>> +				regulator-max-microvolt = <800000>;
>>  				regulator-boot-on;
>>  				regulator-always-on;
>>  			};
>> -- 
>> 2.33.0
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Shawn Guo]

On Tue, Oct 05, 2021 at 03:14:40PM +0200, Frieder Schrempf wrote:
> On 05.10.21 08:56, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:26PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> According to the datasheet VDD_SNVS should be 800 mV, so let's
> >> make sure that the voltage won't be different.
> > 
> > Could you share the datasheet?
> 
> Sure, it's here: https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf.
> See table 10 for the operating voltages.

Thanks for the link!

But datasheet specifies a voltage range. 800 mV is just the typical one.
The only problem I see is that regulator-min-microvolt should be lowered
to 800 mV.  regulator-max-microvolt looks correct to me.

Shawn

> 
> >>
> >> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> >> Cc: stable@vger.kernel.org
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
> >>  1 file changed, 2 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> index b12fb7ce6686..213014f59b46 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> @@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
> >>  
> >>  			reg_vdd_snvs: LDO2 {
> >>  				regulator-name = "ldo2";
> >> -				regulator-min-microvolt = <850000>;
> >> -				regulator-max-microvolt = <900000>;
> >> +				regulator-min-microvolt = <800000>;
> >> +				regulator-max-microvolt = <800000>;
> >>  				regulator-boot-on;
> >>  				regulator-always-on;
> >>  			};
> >> -- 
> >> 2.33.0
> >>

Re: [PATCH 3/8] arm64: dts: imx8mm-kontron: Set VDD_SNVS to 800 mV

[Shawn Guo]

On Tue, Oct 05, 2021 at 03:14:40PM +0200, Frieder Schrempf wrote:
> On 05.10.21 08:56, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:26PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> According to the datasheet VDD_SNVS should be 800 mV, so let's
> >> make sure that the voltage won't be different.
> > 
> > Could you share the datasheet?
> 
> Sure, it's here: https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf.
> See table 10 for the operating voltages.

Thanks for the link!

But datasheet specifies a voltage range. 800 mV is just the typical one.
The only problem I see is that regulator-min-microvolt should be lowered
to 800 mV.  regulator-max-microvolt looks correct to me.

Shawn

> 
> >>
> >> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> >> Cc: stable@vger.kernel.org
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ++--
> >>  1 file changed, 2 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> index b12fb7ce6686..213014f59b46 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> >> @@ -152,8 +152,8 @@ reg_nvcc_snvs: LDO1 {
> >>  
> >>  			reg_vdd_snvs: LDO2 {
> >>  				regulator-name = "ldo2";
> >> -				regulator-min-microvolt = <850000>;
> >> -				regulator-max-microvolt = <900000>;
> >> +				regulator-min-microvolt = <800000>;
> >> +				regulator-max-microvolt = <800000>;
> >>  				regulator-boot-on;
> >>  				regulator-always-on;
> >>  			};
> >> -- 
> >> 2.33.0
> >>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The regulator reg_vdd_5v represents the fixed 5V supply on the board which
can't be switched off. Mark it as always-on.

The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deassertet anytime. Fix the polarity and mark it as always-on.

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 62ba3bd08a0c..f2c8ccefd1bf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
 		regulator-name = "rst-usb-eth2";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usb_eth2>;
-		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
 	};
 
 	reg_vdd_5v: regulator-5v {
@@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
 		regulator-name = "vdd-5v";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
 	};
 };
 
-- 
2.33.0

[PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The regulator reg_vdd_5v represents the fixed 5V supply on the board which
can't be switched off. Mark it as always-on.

The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deassertet anytime. Fix the polarity and mark it as always-on.

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 62ba3bd08a0c..f2c8ccefd1bf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
 		regulator-name = "rst-usb-eth2";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usb_eth2>;
-		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
 	};
 
 	reg_vdd_5v: regulator-5v {
@@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
 		regulator-name = "vdd-5v";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
 	};
 };
 
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
> can't be switched off. Mark it as always-on.
> 
> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
> adapter deassertet anytime. Fix the polarity and mark it as always-on.

It seems to be wrong from the beginning that the reset is modelled by a
regulator.

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
>  1 file changed, 4 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index 62ba3bd08a0c..f2c8ccefd1bf 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
>  		regulator-name = "rst-usb-eth2";
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_usb_eth2>;
> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
>  	};
>  
>  	reg_vdd_5v: regulator-5v {
> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
>  		regulator-name = "vdd-5v";
>  		regulator-min-microvolt = <5000000>;
>  		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;

You do not have any on/off control over the regulator.  So how does this
always-on property make any difference?

Shawn

>  	};
>  };
>  
> -- 
> 2.33.0
> 

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
> can't be switched off. Mark it as always-on.
> 
> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
> adapter deassertet anytime. Fix the polarity and mark it as always-on.

It seems to be wrong from the beginning that the reset is modelled by a
regulator.

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
>  1 file changed, 4 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index 62ba3bd08a0c..f2c8ccefd1bf 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
>  		regulator-name = "rst-usb-eth2";
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_usb_eth2>;
> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
>  	};
>  
>  	reg_vdd_5v: regulator-5v {
> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
>  		regulator-name = "vdd-5v";
>  		regulator-min-microvolt = <5000000>;
>  		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;

You do not have any on/off control over the regulator.  So how does this
always-on property make any difference?

Shawn

>  	};
>  };
>  
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Frieder Schrempf]

On 05.10.21 09:09, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
>> can't be switched off. Mark it as always-on.
>>
>> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
>> adapter deassertet anytime. Fix the polarity and mark it as always-on.
> 
> It seems to be wrong from the beginning that the reset is modelled by a
> regulator.

Right, but at least at the time when I upstreamed this, there was no way
to pass the reset GPIO to a USB device driver and using a regulator
seems to be an accepted workaround as far as I understand.

> 
>>
>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
>>  1 file changed, 4 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> index 62ba3bd08a0c..f2c8ccefd1bf 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
>>  		regulator-name = "rst-usb-eth2";
>>  		pinctrl-names = "default";
>>  		pinctrl-0 = <&pinctrl_usb_eth2>;
>> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
>> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +		regulator-always-on;
>>  	};
>>  
>>  	reg_vdd_5v: regulator-5v {
>> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
>>  		regulator-name = "vdd-5v";
>>  		regulator-min-microvolt = <5000000>;
>>  		regulator-max-microvolt = <5000000>;
>> +		regulator-always-on;
> 
> You do not have any on/off control over the regulator.  So how does this
> always-on property make any difference?

Right, this doesn't make a difference and is definitely not a fix, I
will drop it. Anyway, this regulator is just there for completeness of
the hardware description.

> 
>>  	};
>>  };
>>  
>> -- 
>> 2.33.0
>>

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Frieder Schrempf]

On 05.10.21 09:09, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
>> can't be switched off. Mark it as always-on.
>>
>> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
>> adapter deassertet anytime. Fix the polarity and mark it as always-on.
> 
> It seems to be wrong from the beginning that the reset is modelled by a
> regulator.

Right, but at least at the time when I upstreamed this, there was no way
to pass the reset GPIO to a USB device driver and using a regulator
seems to be an accepted workaround as far as I understand.

> 
>>
>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
>>  1 file changed, 4 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> index 62ba3bd08a0c..f2c8ccefd1bf 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
>>  		regulator-name = "rst-usb-eth2";
>>  		pinctrl-names = "default";
>>  		pinctrl-0 = <&pinctrl_usb_eth2>;
>> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
>> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +		regulator-always-on;
>>  	};
>>  
>>  	reg_vdd_5v: regulator-5v {
>> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
>>  		regulator-name = "vdd-5v";
>>  		regulator-min-microvolt = <5000000>;
>>  		regulator-max-microvolt = <5000000>;
>> +		regulator-always-on;
> 
> You do not have any on/off control over the regulator.  So how does this
> always-on property make any difference?

Right, this doesn't make a difference and is definitely not a fix, I
will drop it. Anyway, this regulator is just there for completeness of
the hardware description.

> 
>>  	};
>>  };
>>  
>> -- 
>> 2.33.0
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Shawn Guo]

On Tue, Oct 05, 2021 at 07:06:57PM +0200, Frieder Schrempf wrote:
> On 05.10.21 09:09, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
> >> can't be switched off. Mark it as always-on.
> >>
> >> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
> >> adapter deassertet anytime. Fix the polarity and mark it as always-on.
> > 
> > It seems to be wrong from the beginning that the reset is modelled by a
> > regulator.
> 
> Right, but at least at the time when I upstreamed this, there was no way
> to pass the reset GPIO to a USB device driver and using a regulator
> seems to be an accepted workaround as far as I understand.

Do we have the solution in usb driver now?  If so, we should probably
switch to that, instead of patching the workaround?

Shawn

> 
> > 
> >>
> >> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> >> Cc: stable@vger.kernel.org
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
> >>  1 file changed, 4 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> index 62ba3bd08a0c..f2c8ccefd1bf 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
> >>  		regulator-name = "rst-usb-eth2";
> >>  		pinctrl-names = "default";
> >>  		pinctrl-0 = <&pinctrl_usb_eth2>;
> >> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
> >> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
> >> +		enable-active-high;
> >> +		regulator-always-on;
> >>  	};
> >>  
> >>  	reg_vdd_5v: regulator-5v {
> >> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
> >>  		regulator-name = "vdd-5v";
> >>  		regulator-min-microvolt = <5000000>;
> >>  		regulator-max-microvolt = <5000000>;
> >> +		regulator-always-on;
> > 
> > You do not have any on/off control over the regulator.  So how does this
> > always-on property make any difference?
> 
> Right, this doesn't make a difference and is definitely not a fix, I
> will drop it. Anyway, this regulator is just there for completeness of
> the hardware description.
> 
> > 
> >>  	};
> >>  };
> >>  
> >> -- 
> >> 2.33.0
> >>

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Shawn Guo]

On Tue, Oct 05, 2021 at 07:06:57PM +0200, Frieder Schrempf wrote:
> On 05.10.21 09:09, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
> >> can't be switched off. Mark it as always-on.
> >>
> >> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
> >> adapter deassertet anytime. Fix the polarity and mark it as always-on.
> > 
> > It seems to be wrong from the beginning that the reset is modelled by a
> > regulator.
> 
> Right, but at least at the time when I upstreamed this, there was no way
> to pass the reset GPIO to a USB device driver and using a regulator
> seems to be an accepted workaround as far as I understand.

Do we have the solution in usb driver now?  If so, we should probably
switch to that, instead of patching the workaround?

Shawn

> 
> > 
> >>
> >> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> >> Cc: stable@vger.kernel.org
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
> >>  1 file changed, 4 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> index 62ba3bd08a0c..f2c8ccefd1bf 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
> >>  		regulator-name = "rst-usb-eth2";
> >>  		pinctrl-names = "default";
> >>  		pinctrl-0 = <&pinctrl_usb_eth2>;
> >> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
> >> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
> >> +		enable-active-high;
> >> +		regulator-always-on;
> >>  	};
> >>  
> >>  	reg_vdd_5v: regulator-5v {
> >> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
> >>  		regulator-name = "vdd-5v";
> >>  		regulator-min-microvolt = <5000000>;
> >>  		regulator-max-microvolt = <5000000>;
> >> +		regulator-always-on;
> > 
> > You do not have any on/off control over the regulator.  So how does this
> > always-on property make any difference?
> 
> Right, this doesn't make a difference and is definitely not a fix, I
> will drop it. Anyway, this regulator is just there for completeness of
> the hardware description.
> 
> > 
> >>  	};
> >>  };
> >>  
> >> -- 
> >> 2.33.0
> >>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Frieder Schrempf]

On 15.10.21 06:09, Shawn Guo wrote:
> On Tue, Oct 05, 2021 at 07:06:57PM +0200, Frieder Schrempf wrote:
>> On 05.10.21 09:09, Shawn Guo wrote:
>>> On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
>>>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>>>
>>>> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
>>>> can't be switched off. Mark it as always-on.
>>>>
>>>> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
>>>> adapter deassertet anytime. Fix the polarity and mark it as always-on.
>>>
>>> It seems to be wrong from the beginning that the reset is modelled by a
>>> regulator.
>>
>> Right, but at least at the time when I upstreamed this, there was no way
>> to pass the reset GPIO to a USB device driver and using a regulator
>> seems to be an accepted workaround as far as I understand.
> 
> Do we have the solution in usb driver now?  If so, we should probably
> switch to that, instead of patching the workaround?

I had a look, but couldn't find anything. I remember there have been
efforts in the past to provide a generic way for usb devices to manage
resources like reset GPIOs and clocks (e.g. [1]), but it seems like
nothing of this ever got merged.

So for the moment I'd like to fix the existing solution, but I totally
agree that this should be solved properly in the future.

[1] https://lkml.org/lkml/2017/6/21/90

> 
>>
>>>
>>>>
>>>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
>>>> Cc: stable@vger.kernel.org
>>>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>>>> ---
>>>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
>>>>  1 file changed, 4 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>>>> index 62ba3bd08a0c..f2c8ccefd1bf 100644
>>>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>>>> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
>>>>  		regulator-name = "rst-usb-eth2";
>>>>  		pinctrl-names = "default";
>>>>  		pinctrl-0 = <&pinctrl_usb_eth2>;
>>>> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
>>>> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
>>>> +		enable-active-high;
>>>> +		regulator-always-on;
>>>>  	};
>>>>  
>>>>  	reg_vdd_5v: regulator-5v {
>>>> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
>>>>  		regulator-name = "vdd-5v";
>>>>  		regulator-min-microvolt = <5000000>;
>>>>  		regulator-max-microvolt = <5000000>;
>>>> +		regulator-always-on;
>>>
>>> You do not have any on/off control over the regulator.  So how does this
>>> always-on property make any difference?
>>
>> Right, this doesn't make a difference and is definitely not a fix, I
>> will drop it. Anyway, this regulator is just there for completeness of
>> the hardware description.
>>
>>>
>>>>  	};
>>>>  };
>>>>  
>>>> -- 
>>>> 2.33.0
>>>>

Re: [PATCH 4/8] arm64: dts: imx8mm-kontron: Fix reg_rst_eth2 and reg_vdd_5v regulators

[Frieder Schrempf]

On 15.10.21 06:09, Shawn Guo wrote:
> On Tue, Oct 05, 2021 at 07:06:57PM +0200, Frieder Schrempf wrote:
>> On 05.10.21 09:09, Shawn Guo wrote:
>>> On Thu, Sep 30, 2021 at 05:56:27PM +0200, Frieder Schrempf wrote:
>>>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>>>
>>>> The regulator reg_vdd_5v represents the fixed 5V supply on the board which
>>>> can't be switched off. Mark it as always-on.
>>>>
>>>> The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
>>>> adapter deassertet anytime. Fix the polarity and mark it as always-on.
>>>
>>> It seems to be wrong from the beginning that the reset is modelled by a
>>> regulator.
>>
>> Right, but at least at the time when I upstreamed this, there was no way
>> to pass the reset GPIO to a USB device driver and using a regulator
>> seems to be an accepted workaround as far as I understand.
> 
> Do we have the solution in usb driver now?  If so, we should probably
> switch to that, instead of patching the workaround?

I had a look, but couldn't find anything. I remember there have been
efforts in the past to provide a generic way for usb devices to manage
resources like reset GPIOs and clocks (e.g. [1]), but it seems like
nothing of this ever got merged.

So for the moment I'd like to fix the existing solution, but I totally
agree that this should be solved properly in the future.

[1] https://lkml.org/lkml/2017/6/21/90

> 
>>
>>>
>>>>
>>>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
>>>> Cc: stable@vger.kernel.org
>>>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>>>> ---
>>>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 5 ++++-
>>>>  1 file changed, 4 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>>>> index 62ba3bd08a0c..f2c8ccefd1bf 100644
>>>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>>>> @@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
>>>>  		regulator-name = "rst-usb-eth2";
>>>>  		pinctrl-names = "default";
>>>>  		pinctrl-0 = <&pinctrl_usb_eth2>;
>>>> -		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
>>>> +		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
>>>> +		enable-active-high;
>>>> +		regulator-always-on;
>>>>  	};
>>>>  
>>>>  	reg_vdd_5v: regulator-5v {
>>>> @@ -78,6 +80,7 @@ reg_vdd_5v: regulator-5v {
>>>>  		regulator-name = "vdd-5v";
>>>>  		regulator-min-microvolt = <5000000>;
>>>>  		regulator-max-microvolt = <5000000>;
>>>> +		regulator-always-on;
>>>
>>> You do not have any on/off control over the regulator.  So how does this
>>> always-on property make any difference?
>>
>> Right, this doesn't make a difference and is definitely not a fix, I
>> will drop it. Anyway, this regulator is just there for completeness of
>> the hardware description.
>>
>>>
>>>>  	};
>>>>  };
>>>>  
>>>> -- 
>>>> 2.33.0
>>>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index f2c8ccefd1bf..dbf11e03ecce 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -98,7 +98,7 @@ can0: can@0 {
 		clocks = <&osc_can>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <100000>;
+		spi-max-frequency = <10000000>;
 		vdd-supply = <&reg_vdd_3v3>;
 		xceiver-supply = <&reg_vdd_5v>;
 	};
-- 
2.33.0

[PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index f2c8ccefd1bf..dbf11e03ecce 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -98,7 +98,7 @@ can0: can@0 {
 		clocks = <&osc_can>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <100000>;
+		spi-max-frequency = <10000000>;
 		vdd-supply = <&reg_vdd_3v3>;
 		xceiver-supply = <&reg_vdd_5v>;
 	};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:28PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
> limit accordingly to prevent any performance issues caused by the
> really low clock speed of 100 kHz.

Could you share some testing result of this change?

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")

It's really an optimization rather than fix, isn't it?

Shawn

> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index f2c8ccefd1bf..dbf11e03ecce 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -98,7 +98,7 @@ can0: can@0 {
>  		clocks = <&osc_can>;
>  		interrupt-parent = <&gpio4>;
>  		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> -		spi-max-frequency = <100000>;
> +		spi-max-frequency = <10000000>;
>  		vdd-supply = <&reg_vdd_3v3>;
>  		xceiver-supply = <&reg_vdd_5v>;
>  	};
> -- 
> 2.33.0
> 

Re: [PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:28PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
> limit accordingly to prevent any performance issues caused by the
> really low clock speed of 100 kHz.

Could you share some testing result of this change?

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")

It's really an optimization rather than fix, isn't it?

Shawn

> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index f2c8ccefd1bf..dbf11e03ecce 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -98,7 +98,7 @@ can0: can@0 {
>  		clocks = <&osc_can>;
>  		interrupt-parent = <&gpio4>;
>  		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> -		spi-max-frequency = <100000>;
> +		spi-max-frequency = <10000000>;
>  		vdd-supply = <&reg_vdd_3v3>;
>  		xceiver-supply = <&reg_vdd_5v>;
>  	};
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Frieder Schrempf]

On 05.10.21 09:12, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:28PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
>> limit accordingly to prevent any performance issues caused by the
>> really low clock speed of 100 kHz.
> 
> Could you share some testing result of this change?

Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').

With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.


> 
>>
>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> 
> It's really an optimization rather than fix, isn't it?

It removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts. As the usage of the CAN bus is
seriously affected by this I would consider it a fix. But if you think
otherwise, feel free to remove the Fixes tag.

> 
> Shawn
> 
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> index f2c8ccefd1bf..dbf11e03ecce 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> @@ -98,7 +98,7 @@ can0: can@0 {
>>  		clocks = <&osc_can>;
>>  		interrupt-parent = <&gpio4>;
>>  		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
>> -		spi-max-frequency = <100000>;
>> +		spi-max-frequency = <10000000>;
>>  		vdd-supply = <&reg_vdd_3v3>;
>>  		xceiver-supply = <&reg_vdd_5v>;
>>  	};
>> -- 
>> 2.33.0
>>

Re: [PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Frieder Schrempf]

On 05.10.21 09:12, Shawn Guo wrote:
> On Thu, Sep 30, 2021 at 05:56:28PM +0200, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
>> limit accordingly to prevent any performance issues caused by the
>> really low clock speed of 100 kHz.
> 
> Could you share some testing result of this change?

Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').

With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.


> 
>>
>> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> 
> It's really an optimization rather than fix, isn't it?

It removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts. As the usage of the CAN bus is
seriously affected by this I would consider it a fix. But if you think
otherwise, feel free to remove the Fixes tag.

> 
> Shawn
> 
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> index f2c8ccefd1bf..dbf11e03ecce 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
>> @@ -98,7 +98,7 @@ can0: can@0 {
>>  		clocks = <&osc_can>;
>>  		interrupt-parent = <&gpio4>;
>>  		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
>> -		spi-max-frequency = <100000>;
>> +		spi-max-frequency = <10000000>;
>>  		vdd-supply = <&reg_vdd_3v3>;
>>  		xceiver-supply = <&reg_vdd_5v>;
>>  	};
>> -- 
>> 2.33.0
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Shawn Guo]

On Tue, Oct 05, 2021 at 07:17:13PM +0200, Frieder Schrempf wrote:
> On 05.10.21 09:12, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:28PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
> >> limit accordingly to prevent any performance issues caused by the
> >> really low clock speed of 100 kHz.
> > 
> > Could you share some testing result of this change?
> 
> Without this change, receiving CAN messages on the board beyond a
> certain bitrate will cause overrun errors (see 'ip -det -stat link show
> can0').
> 
> With this fix, receiving messages on the bus works without any overrun
> errors for bitrates up to 1 MBit.
> 
> 
> > 
> >>
> >> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> > 
> > It's really an optimization rather than fix, isn't it?
> 
> It removes the arbitrarily low limit on the SPI frequency, that was
> caused by a typo in the original dts. As the usage of the CAN bus is
> seriously affected by this I would consider it a fix. But if you think
> otherwise, feel free to remove the Fixes tag.

Put all these good information into commit log, and I will be happy to
take it as a fix.

Shawn

> >> Cc: stable@vger.kernel.org
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
> >>  1 file changed, 1 insertion(+), 1 deletion(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> index f2c8ccefd1bf..dbf11e03ecce 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> @@ -98,7 +98,7 @@ can0: can@0 {
> >>  		clocks = <&osc_can>;
> >>  		interrupt-parent = <&gpio4>;
> >>  		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> >> -		spi-max-frequency = <100000>;
> >> +		spi-max-frequency = <10000000>;
> >>  		vdd-supply = <&reg_vdd_3v3>;
> >>  		xceiver-supply = <&reg_vdd_5v>;
> >>  	};
> >> -- 
> >> 2.33.0
> >>

Re: [PATCH 5/8] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Shawn Guo]

On Tue, Oct 05, 2021 at 07:17:13PM +0200, Frieder Schrempf wrote:
> On 05.10.21 09:12, Shawn Guo wrote:
> > On Thu, Sep 30, 2021 at 05:56:28PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
> >> limit accordingly to prevent any performance issues caused by the
> >> really low clock speed of 100 kHz.
> > 
> > Could you share some testing result of this change?
> 
> Without this change, receiving CAN messages on the board beyond a
> certain bitrate will cause overrun errors (see 'ip -det -stat link show
> can0').
> 
> With this fix, receiving messages on the bus works without any overrun
> errors for bitrates up to 1 MBit.
> 
> 
> > 
> >>
> >> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> > 
> > It's really an optimization rather than fix, isn't it?
> 
> It removes the arbitrarily low limit on the SPI frequency, that was
> caused by a typo in the original dts. As the usage of the CAN bus is
> seriously affected by this I would consider it a fix. But if you think
> otherwise, feel free to remove the Fixes tag.

Put all these good information into commit log, and I will be happy to
take it as a fix.

Shawn

> >> Cc: stable@vger.kernel.org
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
> >>  1 file changed, 1 insertion(+), 1 deletion(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> index f2c8ccefd1bf..dbf11e03ecce 100644
> >> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> >> @@ -98,7 +98,7 @@ can0: can@0 {
> >>  		clocks = <&osc_can>;
> >>  		interrupt-parent = <&gpio4>;
> >>  		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> >> -		spi-max-frequency = <100000>;
> >> +		spi-max-frequency = <10000000>;
> >>  		vdd-supply = <&reg_vdd_3v3>;
> >>  		xceiver-supply = <&reg_vdd_5v>;
> >>  	};
> >> -- 
> >> 2.33.0
> >>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/8] arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Previously we falsely relied on the PHY driver to unconditionally
enable the internal RX delay. Since the following fix for the PHY
driver this is not the case anymore:

commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
delays for RGMII")

In order to enable the delay we need to set the connection type to
"rgmii-rxid".

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index dbf11e03ecce..0e4509287a92 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -114,7 +114,7 @@ &ecspi3 {
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii";
+	phy-connection-type = "rgmii-rxid";
 	phy-handle = <&ethphy>;
 	status = "okay";
 
-- 
2.33.0

Re: [PATCH 6/8] arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY

[Heiko Thiery]

From: Frieder Schrempf <frieder@fris.de>

Hi Frieder,

> Previously we falsely relied on the PHY driver to unconditionally
> enable the internal RX delay. Since the following fix for the PHY
> driver this is not the case anymore:
>
> commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
> delays for RGMII")
>
> In order to enable the delay we need to set the connection type to
> "rgmii-rxid".
>
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

Tested-by: Heiko Thiery <heiko.thiery@gmail.com>

-- 
Heiko

---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index dbf11e03ecce..0e4509287a92 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -114,7 +114,7 @@ &ecspi3 {
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii";
+	phy-connection-type = "rgmii-rxid";
 	phy-handle = <&ethphy>;
 	status = "okay";
 
-- 
2.33.0



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/8] arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY

[Heiko Thiery]

From: Frieder Schrempf <frieder@fris.de>

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Previously we falsely relied on the PHY driver to unconditionally
enable the internal RX delay. Since the following fix for the PHY
driver this is not the case anymore:

commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
delays for RGMII")

In order to enable the delay we need to set the connection type to
"rgmii-rxid".

Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index dbf11e03ecce..0e4509287a92 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -114,7 +114,7 @@ &ecspi3 {
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii";
+	phy-connection-type = "rgmii-rxid";
 	phy-handle = <&ethphy>;
 	status = "okay";
 
-- 
2.33.0



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 6/8] arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:29PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> Previously we falsely relied on the PHY driver to unconditionally
> enable the internal RX delay. Since the following fix for the PHY
> driver this is not the case anymore:
> 
> commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
> delays for RGMII")
> 
> In order to enable the delay we need to set the connection type to
> "rgmii-rxid".

Could you share some details of the issue that the delay is not enabled,
e.g. how broken the Ethernet support is without this change?

Shawn

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index dbf11e03ecce..0e4509287a92 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -114,7 +114,7 @@ &ecspi3 {
>  &fec1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_enet>;
> -	phy-connection-type = "rgmii";
> +	phy-connection-type = "rgmii-rxid";
>  	phy-handle = <&ethphy>;
>  	status = "okay";
>  
> -- 
> 2.33.0
> 

Re: [PATCH 6/8] arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:29PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> Previously we falsely relied on the PHY driver to unconditionally
> enable the internal RX delay. Since the following fix for the PHY
> driver this is not the case anymore:
> 
> commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
> delays for RGMII")
> 
> In order to enable the delay we need to set the connection type to
> "rgmii-rxid".

Could you share some details of the issue that the delay is not enabled,
e.g. how broken the Ethernet support is without this change?

Shawn

> 
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> index dbf11e03ecce..0e4509287a92 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> @@ -114,7 +114,7 @@ &ecspi3 {
>  &fec1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_enet>;
> -	phy-connection-type = "rgmii";
> +	phy-connection-type = "rgmii-rxid";
>  	phy-handle = <&ethphy>;
>  	status = "okay";
>  
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 7/8] arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

According to the datasheet the VSC8531 PHY expects a reset pulse of 100 ns
and a delay of 15 ms after the reset has been deasserted. Set the matching
values in the devicetree.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 0e4509287a92..106e13945ae5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -124,8 +124,8 @@ mdio {
 
 		ethphy: ethernet-phy@0 {
 			reg = <0>;
-			reset-assert-us = <100>;
-			reset-deassert-us = <100>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
 			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 		};
 	};
-- 
2.33.0

[PATCH 7/8] arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

According to the datasheet the VSC8531 PHY expects a reset pulse of 100 ns
and a delay of 15 ms after the reset has been deasserted. Set the matching
values in the devicetree.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 0e4509287a92..106e13945ae5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -124,8 +124,8 @@ mdio {
 
 		ethphy: ethernet-phy@0 {
 			reg = <0>;
-			reset-assert-us = <100>;
-			reset-deassert-us = <100>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
 			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 		};
 	};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 8/8] arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

When the cpufreq driver is enabled, the buck2 regulator is kept powered on
by the dependency between the CPU nodes with 'cpu-supply' set. Without the
cpufreq driver the kernel will power off the regulator as it doesn't see
any users. This is obviously not what we want, therefore keep the regulator
powered on in any case.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 213014f59b46..c3418d263eb4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -105,6 +105,7 @@ reg_vdd_arm: BUCK2 {
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
+				regulator-always-on;
 				regulator-ramp-delay = <3125>;
 				nxp,dvs-run-voltage = <950000>;
 				nxp,dvs-standby-voltage = <850000>;
-- 
2.33.0

[PATCH 8/8] arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

When the cpufreq driver is enabled, the buck2 regulator is kept powered on
by the dependency between the CPU nodes with 'cpu-supply' set. Without the
cpufreq driver the kernel will power off the regulator as it doesn't see
any users. This is obviously not what we want, therefore keep the regulator
powered on in any case.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 213014f59b46..c3418d263eb4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -105,6 +105,7 @@ reg_vdd_arm: BUCK2 {
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
+				regulator-always-on;
 				regulator-ramp-delay = <3125>;
 				nxp,dvs-run-voltage = <950000>;
 				nxp,dvs-standby-voltage = <850000>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 8/8] arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

[Heiko Thiery]

Hi Frieder,

Am Do., 30. Sept. 2021 um 17:57 Uhr schrieb Frieder Schrempf <frieder@fris.de>:
>
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>
> When the cpufreq driver is enabled, the buck2 regulator is kept powered on
> by the dependency between the CPU nodes with 'cpu-supply' set. Without the
> cpufreq driver the kernel will power off the regulator as it doesn't see
> any users. This is obviously not what we want, therefore keep the regulator
> powered on in any case.
>
> Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

Tested-by: Heiko Thiery <heiko.thiery@gmail.com>

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 213014f59b46..c3418d263eb4 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -105,6 +105,7 @@ reg_vdd_arm: BUCK2 {
>                                 regulator-min-microvolt = <850000>;
>                                 regulator-max-microvolt = <950000>;
>                                 regulator-boot-on;
> +                               regulator-always-on;
>                                 regulator-ramp-delay = <3125>;
>                                 nxp,dvs-run-voltage = <950000>;
>                                 nxp,dvs-standby-voltage = <850000>;
> --
> 2.33.0
>

Re: [PATCH 8/8] arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

[Heiko Thiery]

Hi Frieder,

Am Do., 30. Sept. 2021 um 17:57 Uhr schrieb Frieder Schrempf <frieder@fris.de>:
>
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>
> When the cpufreq driver is enabled, the buck2 regulator is kept powered on
> by the dependency between the CPU nodes with 'cpu-supply' set. Without the
> cpufreq driver the kernel will power off the regulator as it doesn't see
> any users. This is obviously not what we want, therefore keep the regulator
> powered on in any case.
>
> Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

Tested-by: Heiko Thiery <heiko.thiery@gmail.com>

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 213014f59b46..c3418d263eb4 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -105,6 +105,7 @@ reg_vdd_arm: BUCK2 {
>                                 regulator-min-microvolt = <850000>;
>                                 regulator-max-microvolt = <950000>;
>                                 regulator-boot-on;
> +                               regulator-always-on;
>                                 regulator-ramp-delay = <3125>;
>                                 nxp,dvs-run-voltage = <950000>;
>                                 nxp,dvs-standby-voltage = <850000>;
> --
> 2.33.0
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 8/8] arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:31PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> When the cpufreq driver is enabled, the buck2 regulator is kept powered on
> by the dependency between the CPU nodes with 'cpu-supply' set. Without the
> cpufreq driver the kernel will power off the regulator as it doesn't see
> any users. This is obviously not what we want, therefore keep the regulator
> powered on in any case.
> 
> Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

Already picked up the one from Heiko.

https://lore.kernel.org/all/20210915120325.20248-1-heiko.thiery@gmail.com/

Shawn

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 213014f59b46..c3418d263eb4 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -105,6 +105,7 @@ reg_vdd_arm: BUCK2 {
>  				regulator-min-microvolt = <850000>;
>  				regulator-max-microvolt = <950000>;
>  				regulator-boot-on;
> +				regulator-always-on;
>  				regulator-ramp-delay = <3125>;
>  				nxp,dvs-run-voltage = <950000>;
>  				nxp,dvs-standby-voltage = <850000>;
> -- 
> 2.33.0
> 

Re: [PATCH 8/8] arm64: dts: imx8mm-kontron: Leave reg_vdd_arm always powered on

[Shawn Guo]

On Thu, Sep 30, 2021 at 05:56:31PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> When the cpufreq driver is enabled, the buck2 regulator is kept powered on
> by the dependency between the CPU nodes with 'cpu-supply' set. Without the
> cpufreq driver the kernel will power off the regulator as it doesn't see
> any users. This is obviously not what we want, therefore keep the regulator
> powered on in any case.
> 
> Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
> Fixes: 21c4f45b335f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
> Cc: stable@vger.kernel.org
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>

Already picked up the one from Heiko.

https://lore.kernel.org/all/20210915120325.20248-1-heiko.thiery@gmail.com/

Shawn

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> index 213014f59b46..c3418d263eb4 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
> @@ -105,6 +105,7 @@ reg_vdd_arm: BUCK2 {
>  				regulator-min-microvolt = <850000>;
>  				regulator-max-microvolt = <950000>;
>  				regulator-boot-on;
> +				regulator-always-on;
>  				regulator-ramp-delay = <3125>;
>  				nxp,dvs-run-voltage = <950000>;
>  				nxp,dvs-standby-voltage = <850000>;
> -- 
> 2.33.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel