From: Baruch Siach <baruch@tkos.co.il>
To: Dave Stevenson <dave.stevenson@raspberrypi.org>,
Eric Anholt <eric@anholt.net>,
Stefan Wahren <stefan.wahren@i2se.com>,
Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-rpi-kernel@lists.infradead.org, devicetree@vger.kernel.org,
Baruch Siach <baruch@tkos.co.il>
Subject: [PATCH 1/4] ARM: bcm2835: sync firmware properties with downstream
Date: Tue, 2 Jan 2018 15:19:18 +0200 [thread overview]
Message-ID: <f791c01097606f29d9572bcdfe3e4aa16d2022e8.1514898134.git.baruch@tkos.co.il> (raw)
In-Reply-To: <cover.1514898134.git.baruch@tkos.co.il>
Add latest firmware property tags from the latest Raspberry Pi downstream
kernel. This is needed for the GPIO tags, so we can control the GPIO
multiplexor lines.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
---
include/soc/bcm2835/raspberrypi-firmware.h | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
index cb979ad90401..50df5b28d2c9 100644
--- a/include/soc/bcm2835/raspberrypi-firmware.h
+++ b/include/soc/bcm2835/raspberrypi-firmware.h
@@ -63,6 +63,7 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_GET_MIN_VOLTAGE = 0x00030008,
RPI_FIRMWARE_GET_TURBO = 0x00030009,
RPI_FIRMWARE_GET_MAX_TEMPERATURE = 0x0003000a,
+ RPI_FIRMWARE_GET_STC = 0x0003000b,
RPI_FIRMWARE_ALLOCATE_MEMORY = 0x0003000c,
RPI_FIRMWARE_LOCK_MEMORY = 0x0003000d,
RPI_FIRMWARE_UNLOCK_MEMORY = 0x0003000e,
@@ -72,12 +73,22 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_SET_ENABLE_QPU = 0x00030012,
RPI_FIRMWARE_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014,
RPI_FIRMWARE_GET_EDID_BLOCK = 0x00030020,
+ RPI_FIRMWARE_GET_CUSTOMER_OTP = 0x00030021,
RPI_FIRMWARE_GET_DOMAIN_STATE = 0x00030030,
RPI_FIRMWARE_SET_CLOCK_STATE = 0x00038001,
RPI_FIRMWARE_SET_CLOCK_RATE = 0x00038002,
RPI_FIRMWARE_SET_VOLTAGE = 0x00038003,
RPI_FIRMWARE_SET_TURBO = 0x00038009,
+ RPI_FIRMWARE_SET_CUSTOMER_OTP = 0x00038021,
RPI_FIRMWARE_SET_DOMAIN_STATE = 0x00038030,
+ RPI_FIRMWARE_GET_GPIO_STATE = 0x00030041,
+ RPI_FIRMWARE_SET_GPIO_STATE = 0x00038041,
+ RPI_FIRMWARE_SET_SDHOST_CLOCK = 0x00038042,
+ RPI_FIRMWARE_GET_GPIO_CONFIG = 0x00030043,
+ RPI_FIRMWARE_SET_GPIO_CONFIG = 0x00038043,
+ RPI_FIRMWARE_GET_PERIPH_REG = 0x00030045,
+ RPI_FIRMWARE_SET_PERIPH_REG = 0x00038045,
+
/* Dispmanx TAGS */
RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE = 0x00040001,
@@ -91,6 +102,8 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_FRAMEBUFFER_GET_VIRTUAL_OFFSET = 0x00040009,
RPI_FIRMWARE_FRAMEBUFFER_GET_OVERSCAN = 0x0004000a,
RPI_FIRMWARE_FRAMEBUFFER_GET_PALETTE = 0x0004000b,
+ RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f,
+ RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF = 0x00040010,
RPI_FIRMWARE_FRAMEBUFFER_RELEASE = 0x00048001,
RPI_FIRMWARE_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT = 0x00044003,
RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT = 0x00044004,
@@ -100,6 +113,7 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_OFFSET = 0x00044009,
RPI_FIRMWARE_FRAMEBUFFER_TEST_OVERSCAN = 0x0004400a,
RPI_FIRMWARE_FRAMEBUFFER_TEST_PALETTE = 0x0004400b,
+ RPI_FIRMWARE_FRAMEBUFFER_TEST_VSYNC = 0x0004400e,
RPI_FIRMWARE_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT = 0x00048003,
RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT = 0x00048004,
RPI_FIRMWARE_FRAMEBUFFER_SET_DEPTH = 0x00048005,
@@ -108,6 +122,10 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009,
RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF = 0x0004801f,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_GPIOVIRTBUF = 0x00048020,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f,
RPI_FIRMWARE_VCHIQ_INIT = 0x00048010,
--
2.15.1
WARNING: multiple messages have this Message-ID (diff)
From: baruch@tkos.co.il (Baruch Siach)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/4] ARM: bcm2835: sync firmware properties with downstream
Date: Tue, 2 Jan 2018 15:19:18 +0200 [thread overview]
Message-ID: <f791c01097606f29d9572bcdfe3e4aa16d2022e8.1514898134.git.baruch@tkos.co.il> (raw)
In-Reply-To: <cover.1514898134.git.baruch@tkos.co.il>
Add latest firmware property tags from the latest Raspberry Pi downstream
kernel. This is needed for the GPIO tags, so we can control the GPIO
multiplexor lines.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
---
include/soc/bcm2835/raspberrypi-firmware.h | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
index cb979ad90401..50df5b28d2c9 100644
--- a/include/soc/bcm2835/raspberrypi-firmware.h
+++ b/include/soc/bcm2835/raspberrypi-firmware.h
@@ -63,6 +63,7 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_GET_MIN_VOLTAGE = 0x00030008,
RPI_FIRMWARE_GET_TURBO = 0x00030009,
RPI_FIRMWARE_GET_MAX_TEMPERATURE = 0x0003000a,
+ RPI_FIRMWARE_GET_STC = 0x0003000b,
RPI_FIRMWARE_ALLOCATE_MEMORY = 0x0003000c,
RPI_FIRMWARE_LOCK_MEMORY = 0x0003000d,
RPI_FIRMWARE_UNLOCK_MEMORY = 0x0003000e,
@@ -72,12 +73,22 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_SET_ENABLE_QPU = 0x00030012,
RPI_FIRMWARE_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014,
RPI_FIRMWARE_GET_EDID_BLOCK = 0x00030020,
+ RPI_FIRMWARE_GET_CUSTOMER_OTP = 0x00030021,
RPI_FIRMWARE_GET_DOMAIN_STATE = 0x00030030,
RPI_FIRMWARE_SET_CLOCK_STATE = 0x00038001,
RPI_FIRMWARE_SET_CLOCK_RATE = 0x00038002,
RPI_FIRMWARE_SET_VOLTAGE = 0x00038003,
RPI_FIRMWARE_SET_TURBO = 0x00038009,
+ RPI_FIRMWARE_SET_CUSTOMER_OTP = 0x00038021,
RPI_FIRMWARE_SET_DOMAIN_STATE = 0x00038030,
+ RPI_FIRMWARE_GET_GPIO_STATE = 0x00030041,
+ RPI_FIRMWARE_SET_GPIO_STATE = 0x00038041,
+ RPI_FIRMWARE_SET_SDHOST_CLOCK = 0x00038042,
+ RPI_FIRMWARE_GET_GPIO_CONFIG = 0x00030043,
+ RPI_FIRMWARE_SET_GPIO_CONFIG = 0x00038043,
+ RPI_FIRMWARE_GET_PERIPH_REG = 0x00030045,
+ RPI_FIRMWARE_SET_PERIPH_REG = 0x00038045,
+
/* Dispmanx TAGS */
RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE = 0x00040001,
@@ -91,6 +102,8 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_FRAMEBUFFER_GET_VIRTUAL_OFFSET = 0x00040009,
RPI_FIRMWARE_FRAMEBUFFER_GET_OVERSCAN = 0x0004000a,
RPI_FIRMWARE_FRAMEBUFFER_GET_PALETTE = 0x0004000b,
+ RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f,
+ RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF = 0x00040010,
RPI_FIRMWARE_FRAMEBUFFER_RELEASE = 0x00048001,
RPI_FIRMWARE_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT = 0x00044003,
RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT = 0x00044004,
@@ -100,6 +113,7 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_OFFSET = 0x00044009,
RPI_FIRMWARE_FRAMEBUFFER_TEST_OVERSCAN = 0x0004400a,
RPI_FIRMWARE_FRAMEBUFFER_TEST_PALETTE = 0x0004400b,
+ RPI_FIRMWARE_FRAMEBUFFER_TEST_VSYNC = 0x0004400e,
RPI_FIRMWARE_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT = 0x00048003,
RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT = 0x00048004,
RPI_FIRMWARE_FRAMEBUFFER_SET_DEPTH = 0x00048005,
@@ -108,6 +122,10 @@ enum rpi_firmware_property_tag {
RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009,
RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF = 0x0004801f,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_GPIOVIRTBUF = 0x00048020,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
+ RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f,
RPI_FIRMWARE_VCHIQ_INIT = 0x00048010,
--
2.15.1
next prev parent reply other threads:[~2018-01-02 13:21 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-02 13:19 [PATCH 0/4] gpio: driver for the RPi3 GPIO expander Baruch Siach
2018-01-02 13:19 ` Baruch Siach
2018-01-02 13:19 ` Baruch Siach [this message]
2018-01-02 13:19 ` [PATCH 1/4] ARM: bcm2835: sync firmware properties with downstream Baruch Siach
2018-01-02 13:19 ` [PATCH 2/4] dt-bindings: gpio: add raspberry pi GPIO expander binding Baruch Siach
2018-01-02 13:19 ` Baruch Siach
2018-01-02 18:26 ` Stefan Wahren
2018-01-02 18:26 ` Stefan Wahren
[not found] ` <860502005.181510.1514917560724-7tX72C7vayboQLBSYMtkGA@public.gmane.org>
2018-01-04 19:35 ` Baruch Siach
2018-01-04 19:35 ` Baruch Siach
2018-01-02 13:19 ` [PATCH 3/4] bcm2835-gpio-exp: Driver for GPIO expander via mailbox service Baruch Siach
2018-01-02 13:19 ` Baruch Siach
2018-01-02 18:49 ` Stefan Wahren
2018-01-02 18:49 ` Stefan Wahren
[not found] ` <2013811470.181895.1514918984637-7tX72C7vayboQLBSYMtkGA@public.gmane.org>
2018-01-09 13:41 ` Baruch Siach
2018-01-09 13:41 ` Baruch Siach
2018-01-09 20:15 ` Stefan Wahren
2018-01-09 20:15 ` Stefan Wahren
2018-01-03 10:08 ` Linus Walleij
2018-01-03 10:08 ` Linus Walleij
2018-01-10 3:45 ` Baruch Siach
2018-01-10 3:45 ` Baruch Siach
2018-01-11 9:39 ` Linus Walleij
2018-01-11 9:39 ` Linus Walleij
[not found] ` <cover.1514898134.git.baruch-NswTu9S1W3P6gbPvEgmw2w@public.gmane.org>
2018-01-02 13:19 ` [PATCH 4/4] ARM: dts: bcm2837-rpi-3-b: add GPIO expander Baruch Siach
2018-01-02 13:19 ` Baruch Siach
[not found] ` <a29df633ee568e150c150debde66c0783a57c70a.1514898134.git.baruch-NswTu9S1W3P6gbPvEgmw2w@public.gmane.org>
2018-01-02 19:03 ` Stefan Wahren
2018-01-02 19:03 ` Stefan Wahren
[not found] ` <1524381852.182115.1514919793281-7tX72C7vayboQLBSYMtkGA@public.gmane.org>
2018-01-03 20:17 ` Stefan Wahren
2018-01-03 20:17 ` Stefan Wahren
2018-01-03 20:29 ` Phil Elwell
2018-01-03 20:29 ` Phil Elwell
[not found] ` <3993684b-5b99-6c38-6247-999f7564762b-FnsA7b+Nu9XbIbC87yuRow@public.gmane.org>
2018-01-04 3:06 ` Peter Robinson
2018-01-04 3:06 ` Peter Robinson
2018-01-02 18:05 ` [PATCH 0/4] gpio: driver for the RPi3 " Stefan Wahren
2018-01-02 18:05 ` Stefan Wahren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f791c01097606f29d9572bcdfe3e4aa16d2022e8.1514898134.git.baruch@tkos.co.il \
--to=baruch@tkos.co.il \
--cc=dave.stevenson@raspberrypi.org \
--cc=devicetree@vger.kernel.org \
--cc=eric@anholt.net \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=stefan.wahren@i2se.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.