From: Jonathan Bakker <xc-racer2@live.ca>
To: kgene@kernel.org, krzk@kernel.org, robh+dt@kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Jonathan Bakker <xc-racer2@live.ca>
Subject: [PATCH v2 08/18] ARM: dts: s5pv210: Add touchkey support to aries boards
Date: Fri, 1 May 2020 16:50:09 -0700 [thread overview]
Message-ID: <BN6PR04MB066049CF813A339C7AFA8FB7A3AB0@BN6PR04MB0660.namprd04.prod.outlook.com> (raw)
In-Reply-To: <20200501235019.24022-1-xc-racer2@live.ca>
Aries boards have soft touchkeys, manufactured by Cypress,
attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
---
arch/arm/boot/dts/s5pv210-aries.dtsi | 58 ++++++++++++++++++++++++++++
1 file changed, 58 insertions(+)
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index 6233884713cb..6683ecec905a 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -16,6 +16,7 @@
i2c6 = &i2c_pmic;
i2c7 = &i2c_musb;
i2c9 = &i2c_fuel;
+ i2c10 = &i2c_touchkey;
};
memory@30000000 {
@@ -50,6 +51,18 @@
gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
};
+ touchkey_vdd: regulator-fixed-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "VTOUCH_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_vdd_ena>;
+ };
+
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
@@ -400,6 +413,32 @@
};
};
+ i2c_touchkey: i2c-gpio-5 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_i2c_pins>;
+
+ touchkey@20 {
+ compatible = "cypress,aries-touchkey";
+ reg = <0x20>;
+ vdd-supply = <&touchkey_vdd>;
+ vcc-supply = <&buck3_reg>;
+ linux,keycodes = <KEY_MENU KEY_BACK
+ KEY_HOMEPAGE KEY_SEARCH>;
+ interrupt-parent = <&gpj4>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_irq>;
+ };
+ };
+
vibrator: pwm-vibrator {
compatible = "pwm-vibrator";
pwms = <&pwm 1 44642 0>;
@@ -530,6 +569,18 @@
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
+ touchkey_i2c_pins: touchkey-i2c-pins {
+ samsung,pins = "gpj3-0", "gpj3-1";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ touchkey_vdd_ena: touchkey-vdd-ena {
+ samsung,pins = "gpj3-2";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
musb_i2c_pins: musb-i2c-pins {
samsung,pins = "gpj3-4", "gpj3-5";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
@@ -542,6 +593,13 @@
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
+ touchkey_irq: touchkey-irq {
+ samsung,pins = "gpj4-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
fg_i2c_pins: fg-i2c-pins {
samsung,pins = "mp05-0", "mp05-1";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
--
2.20.1
next prev parent reply other threads:[~2020-05-01 23:51 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200426183604.28494-1-xc-racer2@live.ca>
2020-04-26 18:35 ` [PATCH 01/13] arm: dts: s5pv210: Add helper define for sleep gpio config Jonathan Bakker
2020-04-26 18:35 ` [PATCH 02/13] arm: dts: s5pv210: fascinate4g: Add sleep GPIO configuration Jonathan Bakker
2020-04-28 10:02 ` Krzysztof Kozlowski
2020-04-28 23:49 ` Jonathan Bakker
2020-05-01 13:10 ` Krzysztof Kozlowski
2020-04-26 18:35 ` [PATCH 03/13] arm: dts: s5pv210: galaxys: " Jonathan Bakker
2020-04-26 18:35 ` [PATCH 04/13] arm: dts: s5pv210: aries: Set keep-power-in-suspend for SDHCI1 Jonathan Bakker
2020-04-26 18:35 ` [PATCH 05/13] arm: dts: s5pv210: aries: Disable pulls on GPIO i2c adapters Jonathan Bakker
2020-04-26 18:35 ` [PATCH 06/13] arm: dts: s5pv210: aries: Add support for more devices Jonathan Bakker
2020-04-28 10:20 ` Krzysztof Kozlowski
2020-04-28 23:32 ` Jonathan Bakker
2020-05-01 13:31 ` Krzysztof Kozlowski
2020-05-01 19:43 ` Jonathan Bakker
2020-04-26 18:35 ` [PATCH 07/13] arm: dts: s5pv210: galaxys: Add si470x fmradio Jonathan Bakker
2020-04-26 18:35 ` [PATCH 08/13] arm: dts: s5pv210: aries: Disable pull for vibrator ena GPIO Jonathan Bakker
2020-04-26 18:36 ` [PATCH 09/13] arm: dts: s5pv210: Add an ADC node Jonathan Bakker
2020-04-28 10:26 ` Krzysztof Kozlowski
2020-04-28 22:27 ` Jonathan Bakker
2020-04-26 18:36 ` [PATCH 10/13] arm: dts: s5pv210: aries: Enable " Jonathan Bakker
2020-04-28 10:29 ` Krzysztof Kozlowski
2020-04-28 22:26 ` Jonathan Bakker
2020-04-26 18:36 ` [PATCH 11/13] arm: dts: s5pv210: Assign clocks to MMC devices Jonathan Bakker
2020-04-26 18:36 ` [PATCH 12/13] arm: dts: s5pv210: Correct FIMC definitions Jonathan Bakker
2020-04-28 10:32 ` Krzysztof Kozlowski
2020-04-28 22:31 ` Jonathan Bakker
2020-04-26 18:36 ` [PATCH 13/13] arm: dts: s5pv210: aries: Set MAX8998 GPIO pulls Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 00/18] S5PV210 and Aries DTS improvements Jonathan Bakker
2020-05-04 15:15 ` Krzysztof Kozlowski
[not found] ` <20200501235019.24022-1-xc-racer2@live.ca>
2020-05-01 23:50 ` [PATCH v2 01/18] ARM: dts: s5pv210: Add helper define for sleep gpio config Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 02/18] ARM: dts: s5pv210: Add sleep GPIO configuration for fascinate4g Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 03/18] ARM: dts: s5pv210: Add sleep GPIO configuration for galaxys Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 04/18] ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 05/18] ARM: dts: s5pv210: Disable pulls on GPIO i2c adapters for aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 06/18] ARM: dts: s5pv210: Add WM8994 support to aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 07/18] ARM: dts: s5pv210: Add FSA9480 support to Aries boards Jonathan Bakker
2020-05-01 23:50 ` Jonathan Bakker [this message]
2020-05-01 23:50 ` [PATCH v2 09/18] ARM: dts: s5pv210: Add panel support to aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 10/18] ARM: dts: s5pv210: Add remaining i2c-gpio adapters to aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 11/18] ARM: dts: s5pv210: Add si470x fmradio to galaxys Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 12/18] ARM: dts: s5pv210: Disable pull for vibrator ena GPIO on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 13/18] ARM: dts: s5pv210: Add an ADC node Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 14/18] ARM: dts: s5pv210: Enable ADC on aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 15/18] ARM: dts: s5pv210: Assign clocks to MMC devices on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 16/18] ARM: dts: s5pv210: Correct FIMC definitions Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 17/18] ARM: dts: s5pv210: Set MAX8998 GPIO pulls on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 18/18] ARM: dts: s5pv210: Correct gpi gpio node name Jonathan Bakker
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=BN6PR04MB066049CF813A339C7AFA8FB7A3AB0@BN6PR04MB0660.namprd04.prod.outlook.com \
--to=xc-racer2@live.ca \
--cc=devicetree@vger.kernel.org \
--cc=kgene@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).